Commit | Line | Data |
---|---|---|
1da177e4 LT |
1 | /* |
2 | * mace.h - definitions for the registers in the Am79C940 MACE | |
3 | * (Medium Access Control for Ethernet) controller. | |
4 | * | |
5 | * Copyright (C) 1996 Paul Mackerras. | |
6 | * | |
7 | * This program is free software; you can redistribute it and/or | |
8 | * modify it under the terms of the GNU General Public License | |
9 | * as published by the Free Software Foundation; either version | |
10 | * 2 of the License, or (at your option) any later version. | |
11 | */ | |
12 | ||
13 | #define REG(x) volatile unsigned char x; char x ## _pad[15] | |
14 | ||
15 | struct mace { | |
16 | REG(rcvfifo); /* receive FIFO */ | |
17 | REG(xmtfifo); /* transmit FIFO */ | |
18 | REG(xmtfc); /* transmit frame control */ | |
19 | REG(xmtfs); /* transmit frame status */ | |
20 | REG(xmtrc); /* transmit retry count */ | |
21 | REG(rcvfc); /* receive frame control */ | |
22 | REG(rcvfs); /* receive frame status (4 bytes) */ | |
23 | REG(fifofc); /* FIFO frame count */ | |
24 | REG(ir); /* interrupt register */ | |
25 | REG(imr); /* interrupt mask register */ | |
26 | REG(pr); /* poll register */ | |
27 | REG(biucc); /* bus interface unit config control */ | |
28 | REG(fifocc); /* FIFO configuration control */ | |
29 | REG(maccc); /* medium access control config control */ | |
30 | REG(plscc); /* phys layer signalling config control */ | |
31 | REG(phycc); /* physical configuration control */ | |
32 | REG(chipid_lo); /* chip ID, lsb */ | |
33 | REG(chipid_hi); /* chip ID, msb */ | |
34 | REG(iac); /* internal address config */ | |
35 | REG(reg19); | |
36 | REG(ladrf); /* logical address filter (8 bytes) */ | |
37 | REG(padr); /* physical address (6 bytes) */ | |
38 | REG(reg22); | |
39 | REG(reg23); | |
40 | REG(mpc); /* missed packet count (clears when read) */ | |
41 | REG(reg25); | |
42 | REG(rntpc); /* runt packet count (clears when read) */ | |
43 | REG(rcvcc); /* recv collision count (clears when read) */ | |
44 | REG(reg28); | |
45 | REG(utr); /* user test reg */ | |
46 | REG(reg30); | |
47 | REG(reg31); | |
48 | }; | |
49 | ||
50 | /* Bits in XMTFC */ | |
51 | #define DRTRY 0x80 /* don't retry transmission after collision */ | |
52 | #define DXMTFCS 0x08 /* don't append FCS to transmitted frame */ | |
53 | #define AUTO_PAD_XMIT 0x01 /* auto-pad short packets on transmission */ | |
54 | ||
55 | /* Bits in XMTFS: only valid when XMTSV is set in PR and XMTFS */ | |
56 | #define XMTSV 0x80 /* transmit status (i.e. XMTFS) valid */ | |
57 | #define UFLO 0x40 /* underflow - xmit fifo ran dry */ | |
58 | #define LCOL 0x20 /* late collision (transmission aborted) */ | |
59 | #define MORE 0x10 /* 2 or more retries needed to xmit frame */ | |
60 | #define ONE 0x08 /* 1 retry needed to xmit frame */ | |
61 | #define DEFER 0x04 /* MACE had to defer xmission (enet busy) */ | |
62 | #define LCAR 0x02 /* loss of carrier (transmission aborted) */ | |
63 | #define RTRY 0x01 /* too many retries (transmission aborted) */ | |
64 | ||
65 | /* Bits in XMTRC: only valid when XMTSV is set in PR (and XMTFS) */ | |
66 | #define EXDEF 0x80 /* had to defer for excessive time */ | |
67 | #define RETRY_MASK 0x0f /* number of retries (0 - 15) */ | |
68 | ||
69 | /* Bits in RCVFC */ | |
70 | #define LLRCV 0x08 /* low latency receive: early DMA request */ | |
71 | #define M_RBAR 0x04 /* sets function of EAM/R pin */ | |
72 | #define AUTO_STRIP_RCV 0x01 /* auto-strip short LLC frames on recv */ | |
73 | ||
74 | /* | |
75 | * Bits in RCVFS. After a frame is received, four bytes of status | |
76 | * are automatically read from this register and appended to the frame | |
77 | * data in memory. These are: | |
78 | * Byte 0 and 1: message byte count and frame status | |
79 | * Byte 2: runt packet count | |
80 | * Byte 3: receive collision count | |
81 | */ | |
82 | #define RS_OFLO 0x8000 /* receive FIFO overflowed */ | |
83 | #define RS_CLSN 0x4000 /* received frame suffered (late) collision */ | |
84 | #define RS_FRAMERR 0x2000 /* framing error flag */ | |
85 | #define RS_FCSERR 0x1000 /* frame had FCS error */ | |
86 | #define RS_COUNT 0x0fff /* mask for byte count field */ | |
87 | ||
88 | /* Bits (fields) in FIFOFC */ | |
89 | #define RCVFC_SH 4 /* receive frame count in FIFO */ | |
90 | #define RCVFC_MASK 0x0f | |
91 | #define XMTFC_SH 0 /* transmit frame count in FIFO */ | |
92 | #define XMTFC_MASK 0x0f | |
93 | ||
94 | /* | |
95 | * Bits in IR and IMR. The IR clears itself when read. | |
96 | * Setting a bit in the IMR will disable the corresponding interrupt. | |
97 | */ | |
98 | #define JABBER 0x80 /* jabber error - 10baseT xmission too long */ | |
99 | #define BABBLE 0x40 /* babble - xmitter xmitting for too long */ | |
100 | #define CERR 0x20 /* collision err - no SQE test (heartbeat) */ | |
101 | #define RCVCCO 0x10 /* RCVCC overflow */ | |
102 | #define RNTPCO 0x08 /* RNTPC overflow */ | |
103 | #define MPCO 0x04 /* MPC overflow */ | |
104 | #define RCVINT 0x02 /* receive interrupt */ | |
105 | #define XMTINT 0x01 /* transmitter interrupt */ | |
106 | ||
107 | /* Bits in PR */ | |
108 | #define XMTSV 0x80 /* XMTFS valid (same as in XMTFS) */ | |
109 | #define TDTREQ 0x40 /* set when xmit fifo is requesting data */ | |
110 | #define RDTREQ 0x20 /* set when recv fifo requests data xfer */ | |
111 | ||
112 | /* Bits in BIUCC */ | |
113 | #define BSWP 0x40 /* byte swap, i.e. big-endian bus */ | |
114 | #define XMTSP_4 0x00 /* start xmitting when 4 bytes in FIFO */ | |
115 | #define XMTSP_16 0x10 /* start xmitting when 16 bytes in FIFO */ | |
116 | #define XMTSP_64 0x20 /* start xmitting when 64 bytes in FIFO */ | |
117 | #define XMTSP_112 0x30 /* start xmitting when 112 bytes in FIFO */ | |
118 | #define SWRST 0x01 /* software reset */ | |
119 | ||
120 | /* Bits in FIFOCC */ | |
121 | #define XMTFW_8 0x00 /* xmit fifo watermark = 8 words free */ | |
122 | #define XMTFW_16 0x40 /* 16 words free */ | |
123 | #define XMTFW_32 0x80 /* 32 words free */ | |
124 | #define RCVFW_16 0x00 /* recv fifo watermark = 16 bytes avail */ | |
125 | #define RCVFW_32 0x10 /* 32 bytes avail */ | |
126 | #define RCVFW_64 0x20 /* 64 bytes avail */ | |
127 | #define XMTFWU 0x08 /* xmit fifo watermark update enable */ | |
128 | #define RCVFWU 0x04 /* recv fifo watermark update enable */ | |
129 | #define XMTBRST 0x02 /* enable transmit burst mode */ | |
130 | #define RCVBRST 0x01 /* enable receive burst mode */ | |
131 | ||
132 | /* Bits in MACCC */ | |
133 | #define PROM 0x80 /* promiscuous mode */ | |
134 | #define DXMT2PD 0x40 /* disable xmit two-part deferral algorithm */ | |
135 | #define EMBA 0x20 /* enable modified backoff algorithm */ | |
136 | #define DRCVPA 0x08 /* disable receiving physical address */ | |
137 | #define DRCVBC 0x04 /* disable receiving broadcasts */ | |
138 | #define ENXMT 0x02 /* enable transmitter */ | |
139 | #define ENRCV 0x01 /* enable receiver */ | |
140 | ||
141 | /* Bits in PLSCC */ | |
142 | #define XMTSEL 0x08 /* select DO+/DO- state when idle */ | |
143 | #define PORTSEL_AUI 0x00 /* select AUI port */ | |
144 | #define PORTSEL_10T 0x02 /* select 10Base-T port */ | |
145 | #define PORTSEL_DAI 0x04 /* select DAI port */ | |
146 | #define PORTSEL_GPSI 0x06 /* select GPSI port */ | |
147 | #define ENPLSIO 0x01 /* enable optional PLS I/O pins */ | |
148 | ||
149 | /* Bits in PHYCC */ | |
150 | #define LNKFL 0x80 /* reports 10Base-T link failure */ | |
151 | #define DLNKTST 0x40 /* disable 10Base-T link test */ | |
152 | #define REVPOL 0x20 /* 10Base-T receiver polarity reversed */ | |
153 | #define DAPC 0x10 /* disable auto receiver polarity correction */ | |
154 | #define LRT 0x08 /* low receive threshold for long links */ | |
155 | #define ASEL 0x04 /* auto-select AUI or 10Base-T port */ | |
156 | #define RWAKE 0x02 /* remote wake function */ | |
157 | #define AWAKE 0x01 /* auto wake function */ | |
158 | ||
159 | /* Bits in IAC */ | |
160 | #define ADDRCHG 0x80 /* request address change */ | |
161 | #define PHYADDR 0x04 /* access physical address */ | |
162 | #define LOGADDR 0x02 /* access multicast filter */ | |
163 | ||
164 | /* Bits in UTR */ | |
165 | #define RTRE 0x80 /* reserved test register enable. DON'T SET. */ | |
166 | #define RTRD 0x40 /* reserved test register disable. Sticky */ | |
167 | #define RPAC 0x20 /* accept runt packets */ | |
168 | #define FCOLL 0x10 /* force collision */ | |
169 | #define RCVFCSE 0x08 /* receive FCS enable */ | |
170 | #define LOOP_NONE 0x00 /* no loopback */ | |
171 | #define LOOP_EXT 0x02 /* external loopback */ | |
172 | #define LOOP_INT 0x04 /* internal loopback, excludes MENDEC */ | |
173 | #define LOOP_MENDEC 0x06 /* internal loopback, includes MENDEC */ |