Guide to using M-Audio Audiophile USB with ALSA and Jack v1.3 ======================================================== Thibault Le Meur This document is a guide to using the M-Audio Audiophile USB (tm) device with ALSA and JACK. 1 - Audiophile USB Specs and correct usage ========================================== This part is a reminder of important facts about the functions and limitations of the device. The device has 4 audio interfaces, and 2 MIDI ports: * Analog Stereo Input (Ai) - This port supports 2 pairs of line-level audio inputs (1/4" TS and RCA) - When the 1/4" TS (jack) connectors are connected, the RCA connectors are disabled * Analog Stereo Output (Ao) * Digital Stereo Input (Di) * Digital Stereo Output (Do) * Midi In (Mi) * Midi Out (Mo) The internal DAC/ADC has the following characteristics: * sample depth of 16 or 24 bits * sample rate from 8kHz to 96kHz * Two ports can't use different sample depths at the same time. Moreover, the Audiophile USB documentation gives the following Warning: "Please exit any audio application running before switching between bit depths" Due to the USB 1.1 bandwidth limitation, a limited number of interfaces can be activated at the same time depending on the audio mode selected: * 16-bit/48kHz ==> 4 channels in/4 channels out - Ai+Ao+Di+Do * 24-bit/48kHz ==> 4 channels in/2 channels out, or 2 channels in/4 channels out - Ai+Ao+Do or Ai+Di+Ao or Ai+Di+Do or Di+Ao+Do * 24-bit/96kHz ==> 2 channels in, or 2 channels out (half duplex only) - Ai or Ao or Di or Do Important facts about the Digital interface: -------------------------------------------- * The Do port additionally supports surround-encoded AC-3 and DTS passthrough, though I haven't tested it under Linux - Note that in this setup only the Do interface can be enabled * Apart from recording an audio digital stream, enabling the Di port is a way to synchronize the device to an external sample clock - As a consequence, the Di port must be enable only if an active Digital source is connected - Enabling Di when no digital source is connected can result in a synchronization error (for instance sound played at an odd sample rate) 2 - Audiophile USB support in ALSA ================================== 2.1 - MIDI ports ---------------- The Audiophile USB MIDI ports will be automatically supported once the following modules have been loaded: * snd-usb-audio * snd-seq-midi No additional setting is required. 2.2 - Audio ports ----------------- Audio functions of the Audiophile USB device are handled by the snd-usb-audio module. This module can work in a default mode (without any device-specific parameter), or in an "advanced" mode with the device-specific parameter called "device_setup". 2.2.1 - Default Alsa driver mode The default behavior of the snd-usb-audio driver is to parse the device capabilities at startup and enable all functions inside the device (including all ports at any supported sample rates and sample depths). This approach has the advantage to let the driver easily switch from sample rates/depths automatically according to the need of the application claiming the device. In this case the Audiophile ports are mapped to alsa pcm devices in the following way (I suppose the device's index is 1): * hw:1,0 is Ao in playback and Di in capture * hw:1,1 is Do in playback and Ai in capture * hw:1,2 is Do in AC3/DTS passthrough mode You must note as well that the device uses Big Endian byte encoding so that supported audio format are S16_BE for 16-bit depth modes and S24_3BE for 24-bits depth mode. One exception is the hw:1,2 port which is Little Endian compliant and thus uses S16_LE. Examples: * playing a S24_3BE encoded raw file to the Ao port % aplay -D hw:1,0 -c2 -t raw -r48000 -fS24_3BE test.raw * recording a S24_3BE encoded raw file from the Ai port % arecord -D hw:1,1 -c2 -t raw -r48000 -fS24_3BE test.raw * playing a S16_BE encoded raw file to the Do port % aplay -D hw:1,1 -c2 -t raw -r48000 -fS16_BE test.raw If you're happy with the default Alsa driver setup and don't experience any issue with this mode, then you can skip the following chapter. 2.2.2 - Advanced module setup Due to the hardware constraints described above, the device initialization made by the Alsa driver in default mode may result in a corrupted state of the device. For instance, a particularly annoying issue is that the sound captured from the Ai port sounds distorted (as if boosted with an excessive high volume gain). For people having this problem, the snd-usb-audio module has a new module parameter called "device_setup". 2.2.2.1 - Initializing the working mode of the Audiophile USB As far as the Audiophile USB device is concerned, this value let the user specify: * the sample depth * the sample rate * whether the Di port is used or not Here is a list of supported device_setup values for this device: * device_setup=0x00 (or omitted) - Alsa driver default mode - maintains backward compatibility with setups that do not use this parameter by not introducing any change - results sometimes in corrupted sound as decribed earlier * device_setup=0x01 - 16bits 48kHz mode with Di disabled - Ai,Ao,Do can be used at the same time - hw:1,0 is not available in capture mode - hw:1,2 is not available * device_setup=0x11 - 16bits 48kHz mode with Di enabled - Ai,Ao,Di,Do can be used at the same time - hw:1,0 is available in capture mode - hw:1,2 is not available * device_setup=0x09 - 24bits 48kHz mode with Di disabled - Ai,Ao,Do can be used at the same time - hw:1,0 is not available in capture mode - hw:1,2 is not available * device_setup=0x19 - 24bits 48kHz mode with Di enabled - 3 ports from {Ai,Ao,Di,Do} can be used at the same time - hw:1,0 is available in capture mode and an active digital source must be connected to Di - hw:1,2 is not available * device_setup=0x0D or 0x10 - 24bits 96kHz mode - Di is enabled by default for this mode but does not need to be connected to an active source - Only 1 port from {Ai,Ao,Di,Do} can be used at the same time - hw:1,0 is available in captured mode - hw:1,2 is not available * device_setup=0x03 - 16bits 48kHz mode with only the Do port enabled - AC3 with DTS passthru (not tested) - Caution with this setup the Do port is mapped to the pcm device hw:1,0 2.2.2.2 - Setting and switching configurations with the device_setup parameter The parameter can be given: * By manually probing the device (as root): # modprobe -r snd-usb-audio # modprobe snd-usb-audio index=1 device_setup=0x09 * Or while configuring the modules options in your modules configuration file - For Fedora distributions, edit the /etc/modprobe.conf file: alias snd-card-1 snd-usb-audio options snd-usb-audio index=1 device_setup=0x09 IMPORTANT NOTE WHEN SWITCHING CONFIGURATION: ------------------------------------------- * You may need to _first_ initialize the module with the correct device_setup parameter and _only_after_ turn on the Audiophile USB device * This is especially true when switching the sample depth: - first turn off the device - de-register the snd-usb-audio module (modprobe -r) - change the device_setup parameter by changing the device_setup option in /etc/modprobe.conf - turn on the device 2.2.2.3 - Audiophile USB's device_setup structure If you want to understand the device_setup magic numbers for the Audiophile USB, you need some very basic understanding of binary computation. However, this is not required to use the parameter and you may skip this section. The device_setup is one byte long and its structure is the following: +---+---+---+---+---+---+---+---+ | b7| b6| b5| b4| b3| b2| b1| b0| +---+---+---+---+---+---+---+---+ | 0 | 0 | 0 | Di|24B|96K|DTS|SET| +---+---+---+---+---+---+---+---+ Where: * b0 is the "SET" bit - it MUST be set if device_setup is initialized * b1 is the "DTS" bit - it is set only for Digital output with DTS/AC3 - this setup is not tested * b2 is the Rate selection flag - When set to "1" the rate range is 48.1-96kHz - Otherwise the sample rate range is 8-48kHz * b3 is the bit depth selection flag - When set to "1" samples are 24bits long - Otherwise they are 16bits long - Note that b2 implies b3 as the 96kHz mode is only supported for 24 bits samples * b4 is the Digital input flag - When set to "1" the device assumes that an active digital source is connected - You shouldn't enable Di if no source is seen on the port (this leads to synchronization issues) - b4 is implied by b2 (since only one port is enabled at a time no synch error can occur) * b5 to b7 are reserved for future uses, and must be set to "0" - might become Ao, Do, Ai, for b7, b6, b4 respectively Caution: * there is no check on the value you will give to device_setup - for instance choosing 0x05 (16bits 96kHz) will fail back to 0x09 since b2 implies b3. But _there_will_be_no_warning_ in /var/log/messages * Hardware constraints due to the USB bus limitation aren't checked - choosing b2 will prepare all interfaces for 24bits/96kHz but you'll only be able to use one at the same time 2.2.3 - USB implementation details for this device You may safely skip this section if you're not interested in driver development. This section describes some internal aspects of the device and summarize the data I got by usb-snooping the windows and Linux drivers. The M-Audio Audiophile USB has 7 USB Interfaces: a "USB interface": * USB Interface nb.0 * USB Interface nb.1 - Audio Control function * USB Interface nb.2 - Analog Output * USB Interface nb.3 - Digital Output * USB Interface nb.4 - Analog Input * USB Interface nb.5 - Digital Input * USB Interface nb.6 - MIDI interface compliant with the MIDIMAN quirk Each interface has 5 altsettings (AltSet 1,2,3,4,5) except: * Interface 3 (Digital Out) has an extra Alset nb.6 * Interface 5 (Digital In) does not have Alset nb.3 and 5 Here is a short description of the AltSettings capabilities: * AltSettings 1 corresponds to - 24-bit depth, 48.1-96kHz sample mode - Adaptive playback (Ao and Do), Synch capture (Ai), or Asynch capture (Di) * AltSettings 2 corresponds to - 24-bit depth, 8-48kHz sample mode - Asynch capture and playback (Ao,Ai,Do,Di) * AltSettings 3 corresponds to - 24-bit depth, 8-48kHz sample mode - Synch capture (Ai) and Adaptive playback (Ao,Do) * AltSettings 4 corresponds to - 16-bit depth, 8-48kHz sample mode - Asynch capture and playback (Ao,Ai,Do,Di) * AltSettings 5 corresponds to - 16-bit depth, 8-48kHz sample mode - Synch capture (Ai) and Adaptive playback (Ao,Do) * AltSettings 6 corresponds to - 16-bit depth, 8-48kHz sample mode - Synch playback (Do), audio format type III IEC1937_AC-3 In order to ensure a correct initialization of the device, the driver _must_know_ how the device will be used: * if DTS is chosen, only Interface 2 with AltSet nb.6 must be registered * if 96KHz only AltSets nb.1 of each interface must be selected * if samples are using 24bits/48KHz then AltSet 2 must me used if Digital input is connected, and only AltSet nb.3 if Digital input is not connected * if samples are using 16bits/48KHz then AltSet 4 must me used if Digital input is connected, and only AltSet nb.5 if Digital input is not connected When device_setup is given as a parameter to the snd-usb-audio module, the parse_audio_endpoints function uses a quirk called "audiophile_skip_setting_quirk" in order to prevent AltSettings not corresponding to device_setup from being registered in the driver. 3 - Audiophile USB and Jack support =================================== This section deals with support of the Audiophile USB device in Jack. The main issue regarding this support is that the device is Big Endian compliant. 3.1 - Using the plug alsa plugin -------------------------------- Jack doesn't directly support big endian devices. Thus, one way to have support for this device with Alsa is to use the Alsa "plug" converter. For instance here is one way to run Jack with 2 playback channels on Ao and 2 capture channels from Ai: % jackd -R -dalsa -dplughw:1 -r48000 -p256 -n2 -D -Cplughw:1,1 However you may see the following warning message: "You appear to be using the ALSA software "plug" layer, probably a result of using the "default" ALSA device. This is less efficient than it could be. Consider using a hardware device instead rather than using the plug layer." 3.2 - Patching alsa to use direct pcm device -------------------------------------------- A patch for Jack by Andreas Steinmetz adds support for Big Endian devices. However it has not been included in the CVS tree. You can find it at the following URL: http://sourceforge.net/tracker/index.php?func=detail&aid=1289682&group_id=39687& atid=425939 After having applied the patch you can run jackd with the following command line: % jackd -R -dalsa -Phw:1,0 -r48000 -p128 -n2 -D -Chw:1,1 3.2 - Getting 2 input and/or output interfaces in Jack ------------------------------------------------------ As you can see, starting the Jack server this way will only enable 1 stereo input (Di or Ai) and 1 stereo output (Ao or Do). This is due to the following restrictions: * Jack can only open one capture device and one playback device at a time * The Audiophile USB is seen as 2 (or three) Alsa devices: hw:1,0, hw:1,1 (and optionally hw:1,2) If you want to get Ai+Di and/or Ao+Do support with Jack, you would need to combine the Alsa devices into one logical "complex" device. If you want to give it a try, I recommend reading the information from this page: http://www.sound-man.co.uk/linuxaudio/ice1712multi.html It is related to another device (ice1712) but can be adapted to suit the Audiophile USB. Enabling multiple Audiophile USB interfaces for Jackd will certainly require: * patching Jack with the previously mentioned "Big Endian" patch * patching Jackd with the MMAP_COMPLEX patch (see the ice1712 page) * patching the alsa-lib/src/pcm/pcm_multi.c file (see the ice1712 page) * define a multi device (combination of hw:1,0 and hw:1,1) in your .asoundrc file * start jackd with this device I had no success in testing this for now, but this may be due to my OS configuration. If you have any success with this kind of setup, please drop me an email.