config MAC80211 tristate "Generic IEEE 802.11 Networking Stack (mac80211)" select CRYPTO select CRYPTO_ECB select CRYPTO_ARC4 select CRYPTO_AES select CRC32 select WIRELESS_EXT select CFG80211 ---help--- This option enables the hardware independent IEEE 802.11 networking stack. config MAC80211_QOS def_bool y depends on MAC80211 depends on NET_SCHED depends on NETDEVICES_MULTIQUEUE comment "QoS/HT support disabled" depends on MAC80211 && !MAC80211_QOS comment "QoS/HT support needs CONFIG_NET_SCHED" depends on MAC80211 && !NET_SCHED comment "QoS/HT support needs CONFIG_NETDEVICES_MULTIQUEUE" depends on MAC80211 && !NETDEVICES_MULTIQUEUE menu "Rate control algorithm selection" depends on MAC80211 != n choice prompt "Default rate control algorithm" default MAC80211_RC_DEFAULT_PID ---help--- This option selects the default rate control algorithm mac80211 will use. Note that this default can still be overriden through the ieee80211_default_rc_algo module parameter if different algorithms are available. config MAC80211_RC_DEFAULT_PID bool "PID controller based rate control algorithm" select MAC80211_RC_PID ---help--- Select the PID controller based rate control as the default rate control algorithm. You should choose this unless you know what you are doing. config MAC80211_RC_DEFAULT_NONE bool "No default algorithm" depends on EMBEDDED help Selecting this option will select no default algorithm and allow you to not build any. Do not choose this option unless you know your driver comes with another suitable algorithm. endchoice comment "Selecting 'y' for an algorithm will" comment "build the algorithm into mac80211." config MAC80211_RC_DEFAULT string default "pid" if MAC80211_RC_DEFAULT_PID default "" config MAC80211_RC_PID tristate "PID controller based rate control algorithm" ---help--- This option enables a TX rate control algorithm for mac80211 that uses a PID controller to select the TX rate. Say Y or M unless you're sure you want to use a different rate control algorithm. endmenu config MAC80211_MESH bool "Enable mac80211 mesh networking (pre-802.11s) support" depends on MAC80211 && EXPERIMENTAL ---help--- This options enables support of Draft 802.11s mesh networking. The implementation is based on Draft 1.08 of the Mesh Networking amendment. For more information visit http://o11s.org/. config MAC80211_LEDS bool "Enable LED triggers" depends on MAC80211 select NEW_LEDS select LEDS_TRIGGERS ---help--- This option enables a few LED triggers for different packet receive/transmit events. config MAC80211_DEBUGFS bool "Export mac80211 internals in DebugFS" depends on MAC80211 && DEBUG_FS ---help--- Select this to see extensive information about the internal state of mac80211 in debugfs. Say N unless you know you need this. config MAC80211_DEBUG_PACKET_ALIGNMENT bool "Enable packet alignment debugging" depends on MAC80211 help This option is recommended for driver authors and strongly discouraged for everybody else, it will trigger a warning when a driver hands mac80211 a buffer that is aligned in a way that will cause problems with the IP stack on some architectures. Say N unless you're writing a mac80211 based driver. config MAC80211_DEBUG bool "Enable debugging output" depends on MAC80211 ---help--- This option will enable debug tracing output for the ieee80211 network stack. If you are not trying to debug or develop the ieee80211 subsystem, you most likely want to say N here. config MAC80211_HT_DEBUG bool "Enable HT debugging output" depends on MAC80211_DEBUG ---help--- This option enables 802.11n High Throughput features debug tracing output. If you are not trying to debug of develop the ieee80211 subsystem, you most likely want to say N here. config MAC80211_VERBOSE_DEBUG bool "Verbose debugging output" depends on MAC80211_DEBUG config MAC80211_LOWTX_FRAME_DUMP bool "Debug frame dumping" depends on MAC80211_DEBUG ---help--- Selecting this option will cause the stack to print a message for each frame that is handed to the lowlevel driver for transmission. This message includes all MAC addresses and the frame control field. If unsure, say N and insert the debugging code you require into the driver you are debugging. config TKIP_DEBUG bool "TKIP debugging" depends on MAC80211_DEBUG config MAC80211_DEBUG_COUNTERS bool "Extra statistics for TX/RX debugging" depends on MAC80211_DEBUG config MAC80211_IBSS_DEBUG bool "Support for IBSS testing" depends on MAC80211_DEBUG ---help--- Say Y here if you intend to debug the IBSS code. config MAC80211_VERBOSE_PS_DEBUG bool "Verbose powersave mode debugging" depends on MAC80211_DEBUG ---help--- Say Y here to print out verbose powersave mode debug messages. config MAC80211_VERBOSE_MPL_DEBUG bool "Verbose mesh peer link debugging" depends on MAC80211_DEBUG && MAC80211_MESH ---help--- Say Y here to print out verbose mesh peer link debug messages.