Supported chips:
* Winbond W83781D
Prefix: 'w83781d'
- Addresses scanned: I2C 0x20 - 0x2f, ISA 0x290 (8 I/O ports)
+ Addresses scanned: I2C 0x28 - 0x2f, ISA 0x290 (8 I/O ports)
Datasheet: http://www.winbond-usa.com/products/winbond_products/pdfs/PCIC/w83781d.pdf
* Winbond W83782D
Prefix: 'w83782d'
- Addresses scanned: I2C 0x20 - 0x2f, ISA 0x290 (8 I/O ports)
+ Addresses scanned: I2C 0x28 - 0x2f, ISA 0x290 (8 I/O ports)
Datasheet: http://www.winbond.com/PDF/sheet/w83782d.pdf
* Winbond W83783S
Prefix: 'w83783s'
Addresses scanned: I2C 0x2d
Datasheet: http://www.winbond-usa.com/products/winbond_products/pdfs/PCIC/w83783s.pdf
- * Winbond W83627HF
- Prefix: 'w83627hf'
- Addresses scanned: I2C 0x20 - 0x2f, ISA 0x290 (8 I/O ports)
- Datasheet: http://www.winbond.com/PDF/sheet/w83627hf.pdf
* Asus AS99127F
Prefix: 'as99127f'
Addresses scanned: I2C 0x28 - 0x2f
Use 'init=0' to bypass initializing the chip.
Try this if your computer crashes when you load the module.
+* reset int
+ (default 0)
+ The driver used to reset the chip on load, but does no more. Use
+ 'reset=1' to restore the old behavior. Report if you need to do this.
+
force_subclients=bus,caddr,saddr,saddr
This is used to force the i2c addresses for subclients of
a certain chip. Typical usage is `force_subclients=0,0x2d,0x4a,0x4b'
Description
-----------
-This driver implements support for the Winbond W83781D, W83782D, W83783S,
-W83627HF chips, and the Asus AS99127F chips. We will refer to them
-collectively as W8378* chips.
+This driver implements support for the Winbond W83781D, W83782D, W83783S
+chips, and the Asus AS99127F chips. We will refer to them collectively as
+W8378* chips.
There is quite some difference between these chips, but they are similar
enough that it was sensible to put them together in one driver.
-The W83627HF chip is assumed to be identical to the ISA W83782D.
The Asus chips are similar to an I2C-only W83782D.
Chip #vin #fanin #pwm #temp wchipid vendid i2c ISA
as99127f 7 3 0 3 0x31 0x12c3 yes no
as99127f rev.2 (type_name = as99127f) 0x31 0x5ca3 yes no
w83781d 7 3 0 3 0x10-1 0x5ca3 yes yes
-w83627hf 9 3 2 3 0x21 0x5ca3 yes yes(LPC)
w83782d 9 3 2-4 3 0x30 0x5ca3 yes yes
w83783s 5-6 3 2 1-2 0x40 0x5ca3 yes no
your computer speaker. It is possible to enable all beeping globally,
or only the beeping for some alarms.
+Individual alarm and beep bits:
+
+0x000001: in0
+0x000002: in1
+0x000004: in2
+0x000008: in3
+0x000010: temp1
+0x000020: temp2 (+temp3 on W83781D)
+0x000040: fan1
+0x000080: fan2
+0x000100: in4
+0x000200: in5
+0x000400: in6
+0x000800: fan3
+0x001000: chassis
+0x002000: temp3 (W83782D only)
+0x010000: in7 (W83782D only)
+0x020000: in8 (W83782D only)
+
If an alarm triggers, it will remain triggered until the hardware register
is read at least once. This means that the cause for the alarm may
already have disappeared! Note that in the current implementation, all