[PATCH] ehea: IBM eHEA Ethernet Device Driver
[linux-2.6] / drivers / net / Kconfig
index 0c6b45a..d30ab6b 100644 (file)
@@ -854,6 +854,17 @@ config SMC9194
          <file:Documentation/networking/net-modules.txt>. The module
          will be called smc9194.
 
+config NET_NETX
+       tristate "NetX Ethernet support"
+       select MII
+       depends on NET_ETHERNET && ARCH_NETX
+       help
+         This is support for the Hilscher netX builtin Ethernet ports
+
+         To compile this driver as a module, choose M here and read
+         <file:Documentation/networking/net-modules.txt>. The module
+         will be called netx-eth.
+
 config DM9000
        tristate "DM9000 support"
        depends on (ARM || MIPS) && NET_ETHERNET
@@ -1289,6 +1300,23 @@ config PCNET32
          <file:Documentation/networking/net-modules.txt>. The module
          will be called pcnet32.
 
+config PCNET32_NAPI
+       bool "Use RX polling (NAPI) (EXPERIMENTAL)"
+       depends on PCNET32 && EXPERIMENTAL
+       help
+         NAPI is a new driver API designed to reduce CPU and interrupt load
+         when the driver is receiving lots of packets from the card. It is
+         still somewhat experimental and thus not yet enabled by default.
+
+         If your estimated Rx load is 10kpps or more, or if the card will be
+         deployed on potentially unfriendly networks (e.g. in a firewall),
+         then say Y here.
+
+         See <file:Documentation/networking/NAPI_HOWTO.txt> for more
+         information.
+
+         If in doubt, say N.
+
 config AMD8111_ETH
        tristate "AMD 8111 (new PCI lance) support"
        depends on NET_PCI && PCI
@@ -1376,8 +1404,8 @@ config APRICOT
          called apricot.
 
 config B44
-       tristate "Broadcom 4400 ethernet support (EXPERIMENTAL)"
-       depends on NET_PCI && PCI && EXPERIMENTAL
+       tristate "Broadcom 4400 ethernet support"
+       depends on NET_PCI && PCI
        select MII
        help
          If you have a network (Ethernet) controller of this type, say Y and
@@ -1400,6 +1428,22 @@ config FORCEDETH
          <file:Documentation/networking/net-modules.txt>.  The module will be
          called forcedeth.
 
+config FORCEDETH_NAPI
+       bool "Use Rx and Tx Polling (NAPI) (EXPERIMENTAL)"
+       depends on FORCEDETH && EXPERIMENTAL
+       help
+         NAPI is a new driver API designed to reduce CPU and interrupt load
+         when the driver is receiving lots of packets from the card. It is
+         still somewhat experimental and thus not yet enabled by default.
+
+         If your estimated Rx load is 10kpps or more, or if the card will be
+         deployed on potentially unfriendly networks (e.g. in a firewall),
+         then say Y here.
+
+         See <file:Documentation/networking/NAPI_HOWTO.txt> for more
+         information.
+
+         If in doubt, say N.
 
 config CS89x0
        tristate "CS89x0 support"
@@ -1713,6 +1757,20 @@ config VIA_RHINE_MMIO
 
          If unsure, say Y.
 
+config VIA_RHINE_NAPI
+       bool "Use Rx Polling (NAPI)"
+       depends on VIA_RHINE
+       help
+         NAPI is a new driver API designed to reduce CPU and interrupt load
+         when the driver is receiving lots of packets from the card.
+
+         If your estimated Rx load is 10kpps or more, or if the card will be
+         deployed on potentially unfriendly networks (e.g. in a firewall),
+         then say Y here.
+
+         See <file:Documentation/networking/NAPI_HOWTO.txt> for more
+         information.
+
 config LAN_SAA9730
        bool "Philips SAA9730 Ethernet support (EXPERIMENTAL)"
        depends on NET_PCI && EXPERIMENTAL && MIPS
@@ -2190,7 +2248,7 @@ config BNX2
 
 config SPIDER_NET
        tristate "Spider Gigabit Ethernet driver"
-       depends on PCI && PPC_CELL
+       depends on PCI && PPC_IBM_CELL_BLADE
        select FW_LOADER
        help
          This driver supports the Gigabit Ethernet chips present on the
@@ -2198,16 +2256,43 @@ config SPIDER_NET
 
 config GIANFAR
        tristate "Gianfar Ethernet"
-       depends on 85xx || 83xx
+       depends on 85xx || 83xx || PPC_86xx
        select PHYLIB
        help
-         This driver supports the Gigabit TSEC on the MPC85xx 
-         family of chips, and the FEC on the 8540
+         This driver supports the Gigabit TSEC on the MPC83xx, MPC85xx,
+         and MPC86xx family of chips, and the FEC on the 8540.
 
 config GFAR_NAPI
        bool "NAPI Support"
        depends on GIANFAR
 
+config UCC_GETH
+       tristate "Freescale QE UCC GETH"
+       depends on QUICC_ENGINE && UCC_FAST
+       help
+         This driver supports the Gigabit Ethernet mode of QE UCC.
+         QE can be found on MPC836x CPUs.
+
+config UGETH_NAPI
+       bool "NAPI Support"
+       depends on UCC_GETH
+
+config UGETH_MAGIC_PACKET
+       bool "Magic Packet detection support"
+       depends on UCC_GETH
+
+config UGETH_FILTERING
+       bool "Mac address filtering support"
+       depends on UCC_GETH
+
+config UGETH_TX_ON_DEMOND
+       bool "Transmit on Demond support"
+       depends on UCC_GETH
+
+config UGETH_HAS_GIGA
+       bool
+       depends on UCC_GETH && MPC836x
+
 config MV643XX_ETH
        tristate "MV-643XX Ethernet support"
        depends on MOMENCO_OCELOT_C || MOMENCO_JAGUAR_ATX || MV64360 || MOMENCO_OCELOT_3 || PPC_MULTIPLATFORM
@@ -2238,6 +2323,15 @@ config MV643XX_ETH_2
          This enables support for Port 2 of the Marvell MV643XX Gigabit
          Ethernet.
 
+config QLA3XXX
+       tristate "QLogic QLA3XXX Network Driver Support"
+       depends on PCI
+       help
+         This driver supports QLogic ISP3XXX gigabit Ethernet cards.
+
+         To compile this driver as a module, choose M here: the module
+         will be called qla3xxx.
+
 endmenu
 
 #
@@ -2266,6 +2360,15 @@ config CHELSIO_T1
           To compile this driver as a module, choose M here: the module
           will be called cxgb.
 
+config EHEA
+       tristate "eHEA Ethernet support"
+       depends on IBMEBUS
+       ---help---
+         This driver supports the IBM pSeries eHEA ethernet adapter.
+
+         To compile the driver as a module, choose M here. The module
+         will be called ehea.
+
 config IXGB
        tristate "Intel(R) PRO/10GbE support"
        depends on PCI
@@ -2341,7 +2444,7 @@ config MYRI10GE
          you will need a newer firmware image.
          You may get this image or more information, at:
 
-         <http://www.myri.com/Myri-10G/>
+         <http://www.myri.com/scs/download-Myri10GE.html>
 
          To compile this driver as a module, choose M here and read
          <file:Documentation/networking/net-modules.txt>.  The module
@@ -2498,6 +2601,7 @@ config PLIP
 
 config PPP
        tristate "PPP (point-to-point protocol) support"
+       select SLHC
        ---help---
          PPP (Point to Point Protocol) is a newer and better SLIP.  It serves
          the same purpose: sending Internet traffic over telephone (and other
@@ -2678,6 +2782,7 @@ config SLIP
 config SLIP_COMPRESSED
        bool "CSLIP compressed headers"
        depends on SLIP
+       select SLHC
        ---help---
          This protocol is faster than SLIP because it uses compression on the
          TCP/IP headers (not on the data itself), but it has to be supported
@@ -2690,6 +2795,12 @@ config SLIP_COMPRESSED
          <http://www.tldp.org/docs.html#howto>, explains how to configure
          CSLIP. This won't enlarge your kernel.
 
+config SLHC
+       tristate
+       help
+         This option enables Van Jacobsen serial line header compression
+         routines.
+
 config SLIP_SMART
        bool "Keepalive and linefill"
        depends on SLIP