---help---
There are two drivers for Serial ATA controllers.
- The main driver, "libata", exists inside the SCSI subsystem
- and supports most modern SATA controllers.
+ The main driver, "libata", uses the SCSI subsystem
+ and supports most modern SATA controllers. In order to use it
+ you may take a look at "Serial ATA (prod) and Parallel ATA
+ (experimental) drivers".
The IDE driver (which you are currently configuring) supports
a few first-generation SATA controllers.
config BLK_DEV_GENERIC
tristate "Generic PCI IDE Chipset Support"
depends on BLK_DEV_IDEPCI
+ help
+ This option provides generic support for various PCI IDE Chipsets
+ which otherwise might not be supported.
config BLK_DEV_OPTI621
tristate "OPTi 82C621 chipset enhanced support (EXPERIMENTAL)"
Generally say N here.
-config IDEDMA_PCI_AUTO
- bool "Use PCI DMA by default when available"
- ---help---
- Prior to kernel version 2.1.112, Linux used to automatically use
- DMA for IDE drives and chipsets which support it. Due to concerns
- about a couple of cases where buggy hardware may have caused damage,
- the default is now to NOT use DMA automatically. To revert to the
- previous behaviour, say Y to this question.
-
- If you suspect your hardware is at all flakey, say N here.
- Do NOT email the IDE kernel people regarding this issue!
-
- It is normally safe to answer Y to this question unless your
- motherboard uses a VIA VP2 chipset, in which case you should say N.
-
config IDEDMA_ONLYDISK
bool "Enable DMA only for disks "
- depends on IDEDMA_PCI_AUTO
help
This is used if you know your ATAPI Devices are going to fail DMA
Transfers.
help
This driver adds support for Toshiba TC86C001 GOKU-S chip.
+config BLK_DEV_CELLEB
+ tristate "Toshiba's Cell Reference Set IDE support"
+ depends on PPC_CELLEB
+ help
+ This driver provides support for the built-in IDE controller on
+ Toshiba Cell Reference Board.
+ If unsure, say Y.
+
endif
config BLK_DEV_IDE_PMAC
to transfer data to and from memory. Saying Y is safe and improves
performance.
-config BLK_DEV_IDE_CELLEB
- bool "Toshiba's Cell Reference Set IDE support"
- depends on PPC_CELLEB
- help
- This driver provides support for the built-in IDE controller on
- Toshiba Cell Reference Board.
- If unsure, say Y.
-
config BLK_DEV_IDE_SWARM
tristate "IDE for Sibyte evaluation boards"
depends on SIBYTE_SB1xxx_SOC
Say Y here if you want to add DMA (Direct Memory Access) support to
the ICS IDE driver.
-config IDEDMA_ICS_AUTO
- bool "Use ICS DMA by default"
- depends on BLK_DEV_IDEDMA_ICS
- help
- Prior to kernel version 2.1.112, Linux used to automatically use
- DMA for IDE drives and chipsets which support it. Due to concerns
- about a couple of cases where buggy hardware may have caused damage,
- the default is now to NOT use DMA automatically. To revert to the
- previous behaviour, say Y to this question.
-
- If you suspect your hardware is at all flakey, say N here.
- Do NOT email the IDE kernel people regarding this issue!
-
config BLK_DEV_IDE_RAPIDE
tristate "RapIDE interface support"
depends on ARM && ARCH_ACORN
config BLK_DEV_ALI14XX
tristate "ALI M14xx support"
help
- This driver is enabled at runtime using the "ide0=ali14xx" kernel
+ This driver is enabled at runtime using the "ali14xx.probe" kernel
boot parameter. It enables support for the secondary IDE interface
of the ALI M1439/1443/1445/1487/1489 chipsets, and permits faster
I/O speeds to be set as well. See the files
config BLK_DEV_DTC2278
tristate "DTC-2278 support"
help
- This driver is enabled at runtime using the "ide0=dtc2278" kernel
+ This driver is enabled at runtime using the "dtc2278.probe" kernel
boot parameter. It enables support for the secondary IDE interface
of the DTC-2278 card, and permits faster I/O speeds to be set as
well. See the <file:Documentation/ide.txt> and
config BLK_DEV_HT6560B
tristate "Holtek HT6560B support"
help
- This driver is enabled at runtime using the "ide0=ht6560b" kernel
+ This driver is enabled at runtime using the "ht6560b.probe" kernel
boot parameter. It enables support for the secondary IDE interface
of the Holtek card, and permits faster I/O speeds to be set as well.
See the <file:Documentation/ide.txt> and
config BLK_DEV_QD65XX
tristate "QDI QD65xx support"
help
- This driver is enabled at runtime using the "ide0=qd65xx" kernel
+ This driver is enabled at runtime using the "qd65xx.probe" kernel
boot parameter. It permits faster I/O speeds to be set. See the
<file:Documentation/ide.txt> and <file:drivers/ide/legacy/qd65xx.c> for
more info.
config BLK_DEV_UMC8672
tristate "UMC-8672 support"
help
- This driver is enabled at runtime using the "ide0=umc8672" kernel
+ This driver is enabled at runtime using the "umc8672.probe" kernel
boot parameter. It enables support for the secondary IDE interface
of the UMC-8672, and permits faster I/O speeds to be set as well.
See the files <file:Documentation/ide.txt> and
It is normally safe to answer Y; however, the default is N.
-config IDEDMA_AUTO
- def_bool IDEDMA_PCI_AUTO || IDEDMA_ICS_AUTO
-
endif
config BLK_DEV_HD_ONLY