Michael Hennerich [Wed, 10 Oct 2007 09:42:55 +0000 (17:42 +0800)] 
Blackfin arch: flush/inv the correct range when using write back cache and fix bugs find by dmacopy
- flush/inv the correct range
- dmacopy test failed when policy is write_back - invalidate before dma
http://blackfin.uclinux.org/gf/project/uclinux-dist/tracker/?action=TrackerItemEdit&tracker_item_id=3367
It's the cache invalidate what is causing the issue.
There is no invalidate only instruction it's always: FLUSHINV
So when we "invalidate" after the DMA we might (do) overwrite freshly
dma'ed data by dirty Cache WB content.
Fixed by moving the "invalidate" at the beginning of dma_memcpy.
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Bryan Wu <bryan.wu@analog.com>
Sonic Zhang [Wed, 10 Oct 2007 08:47:58 +0000 (16:47 +0800)] 
Blackfin arch: update kgdb patch
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Bryan Wu <bryan.wu@analog.com>
Michael Hennerich [Wed, 10 Oct 2007 08:58:49 +0000 (16:58 +0800)]
Blackfin arch: Comply with revised Anomaly Workarounds for BF533
05000311 and BF561
05000323
Comply with revised Anomaly Workarounds for BF533
05000311 and BF561
05000323
accoring to BF533 anomaly sheet Rev. A 09/04/07
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Bryan Wu <bryan.wu@analog.com>
Robin Getz [Tue, 9 Oct 2007 09:31:46 +0000 (17:31 +0800)] 
Blackfin arch: Print out debug info, as early as possible
Print out debug info, as early as possible - even before the
kernel initializes the interrupt vectors. Now we can print out debug
messages almost anytime during the boot process.
Signed-off-by: Robin Getz <robin.getz@analog.com>
Signed-off-by: Bryan Wu <bryan.wu@analog.com>
Robin Getz [Tue, 9 Oct 2007 09:28:36 +0000 (17:28 +0800)]
Blackfin arch: Enable earlyprintk earlier - so any error after our interrupt tables are set up will print out
Also ensure that the traps_c code doesn't cause a double fault, by
sending a signal to a faulting kernel before the memory subsystem
is fully initialized, by printing out the error message before sending
the signal.
Signed-off-by: Robin Getz <robin.getz@analog.com>
Signed-off-by: Bryan Wu <bryan.wu@analog.com>
Robin Getz [Tue, 9 Oct 2007 09:24:30 +0000 (17:24 +0800)]
Blackfin arch: fix endless loop bug when a double fault happens
Today when a double fault happens (exception during an exception
handling event), we go into an endless loop, with nothing comming out
the UART. With this patch, we actually see that we have commited a
double fault event
Signed-off-by: Robin Getz <robin.getz@analog.com>
Signed-off-by: Bryan Wu <bryan.wu@analog.com>
Robin Getz [Tue, 9 Oct 2007 09:24:49 +0000 (17:24 +0800)]
Blackfin arch: Initial patch to add earlyprintk support
This allows debugging of problems which happen eary in the kernel
boot process (after bootargs are parsed, but before serial subsystem
is fully initialized)
Signed-off-by: Robin Getz <robin.getz@analog.com>
Signed-off-by: Bryan Wu <bryan.wu@analog.com>
Bryan Wu [Wed, 10 Oct 2007 16:30:56 +0000 (00:30 +0800)] 
Blackfin arch: add TWIx_REGBASE and SPIx_REGBASE to specific CPU header files, use the new REGBASE for board platform resources
Signed-off-by: Bryan Wu <bryan.wu@analog.com>
Bryan Wu [Tue, 9 Oct 2007 07:09:49 +0000 (15:09 +0800)]
Blackfin arch: modify the insX/outsX and dma_insX/dma_outsX to be compatible with other archs
Signed-off-by: Bryan Wu <bryan.wu@analog.com>
Mike Frysinger [Wed, 10 Oct 2007 16:12:41 +0000 (00:12 +0800)] 
Blackfin arch: add more common defines for output sections
Signed-off-by: Mike Frysinger <michael.frysinger@analog.com>
Signed-off-by: Bryan Wu <bryan.wu@analog.com>
Bryan Wu [Wed, 12 Sep 2007 09:48:25 +0000 (17:48 +0800)]
Blackfin arch: cleanup IO and DMA_IO API function definitions according to other arches
Signed-off-by: Bryan Wu <bryan.wu@analog.com>
Mike Frysinger [Wed, 12 Sep 2007 09:31:59 +0000 (17:31 +0800)]
Blackfin arch: fix typo pointed out by David Rowe (Mhz -> MHz)
Signed-off-by: Mike Frysinger <michael.frysinger@analog.com>
Signed-off-by: Bryan Wu <bryan.wu@analog.com>
Michael Hennerich [Wed, 10 Oct 2007 16:29:49 +0000 (00:29 +0800)]
Blackfin arch: Workaround reboot bug, issue SSYNC at the start of bfin_reset
reboot failes on BF533
http://blackfin.uclinux.org/gf/project/uclinux-dist/tracker/?action=TrackerItemEdit&tracker_item_id=3500
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Bryan Wu <bryan.wu@analog.com>
Michael Hennerich [Wed, 12 Sep 2007 06:50:28 +0000 (14:50 +0800)]
Blackfin arch: Add ANOMALY_05000311 Workaround - for those who doesnt use the generic GPIO driver
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Bryan Wu <bryan.wu@analog.com>
Michael Hennerich [Tue, 28 Aug 2007 06:57:05 +0000 (14:57 +0800)]
Blackfin arch: Remove legacy support
Now that there is a generic GPIO driver framework
remove GPIO register unified name space legacy support.
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Bryan Wu <bryan.wu@analog.com>
Michael Hennerich [Wed, 10 Oct 2007 16:24:40 +0000 (00:24 +0800)]
Blackfin arch: a few things still use bfin_read_PORT_FER()
- Update gpio_request to allow multiple request with the same signature (label)
- Use generic GPIO API where applicable
- Update generic board support form stamp board
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Bryan Wu <bryan.wu@analog.com>
Michael Hennerich [Wed, 10 Oct 2007 16:06:31 +0000 (00:06 +0800)]
Blackfin arch: For compatibility reasons change IRQ_XXX_ERR into IRQ_XXX_ERROR like on any other supported Blackfin derivative
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Bryan Wu <bryan.wu@analog.com>
Robin Getz [Mon, 27 Aug 2007 09:38:40 +0000 (17:38 +0800)]
Blackfin arch: Remove cruft - CONFIG_DEBUG_SERIAL_EARLY_INIT didn't work that well with DEBUG_KERNEL_START
Signed-off-by: Robin Getz <robin.getz@analog.com>
Signed-off-by: Bryan Wu <bryan.wu@analog.com>
Michael Hennerich [Tue, 28 Aug 2007 08:47:46 +0000 (16:47 +0800)]
Blackfin arch: Merge GPIO/Peripheral Resource Allocation back into a single file
Signed-off-by: Michael Hennerich <michale.hennerich@analog.com>
Signed-off-by: Bryan Wu <bryan.wu@analog.com>
Robin Getz [Thu, 13 Sep 2007 03:49:33 +0000 (11:49 +0800)]
Blackfin arch: Fix bug missing L2_MEMORY definition for EZKIT-BF561 compiling error
Signed-off-by: Robin Getz <robin.getz@analog.com>
Signed-off-by: Bryan Wu <bryan.wu@analog.com>
Michael Hennerich [Mon, 27 Aug 2007 08:46:17 +0000 (16:46 +0800)]
Blackfin arch: extract gpio number from PIN function
Singed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Bryan Wu <bryan.wu@analog.com>
Mike Frysinger [Wed, 10 Oct 2007 16:22:35 +0000 (00:22 +0800)]
Blackfin arch: rewrite our reboot code in C
rewrite our reboot code in C rather than assembly to be like
other architectures and to allow board maintainers to define
custom behavior
Signed-off-by: Mike Frysinger <michael.frysinger@analog.com>
Signed-off-by: Bryan Wu <bryan.wu@analog.com>
Mike Frysinger [Mon, 27 Aug 2007 08:08:53 +0000 (16:08 +0800)]
Blackfin arch: vmlinux.lds.S, break up our .init into separate sections
Break up our .init into separate section like all other ports do and
so that we dont mix text and data (causes disassembly headaches as
pointed out by Robin)
Cc: Robin Getz <robin.getz@analog.com>
Signed-off-by: Mike Frysinger <michael.frysinger@analog.com>
Signed-off-by: Bryan Wu <bryan.wu@analog.com>
Bryan Wu [Wed, 10 Oct 2007 16:03:39 +0000 (00:03 +0800)]
Blackfin arch: Board defconfig updating
Signed-off-by: Bryan Wu <bryan.wu@analog.com>
Mike Frysinger [Mon, 27 Aug 2007 07:02:20 +0000 (15:02 +0800)]
Blackfin arch: parse input sections properly when using -ffunction-sections/-fdata-sections
Signed-off-by: Mike Frysinger <michael.frysinger@analog.com>
Signed-off-by: Bryan Wu <bryan.wu@analog.com>
Mike Frysinger [Sun, 5 Aug 2007 09:14:04 +0000 (17:14 +0800)]
Blackfin arch: add an exception request/free api
add an exception request/free api similar to the interrupt request/fre
api so people can utilize the free software based exceptions for their
own purposes
Signed-off-by: Mike Frysinger <michael.frysinger@analog.com>
Signed-off-by: Bryan Wu <bryan.wu@analog.com>
Mike Frysinger [Sun, 5 Aug 2007 09:06:48 +0000 (17:06 +0800)]
Blackfin arch: all our other ports call this SIZE rather than SPI_LEN
Signed-off-by: Mike Frysinger <michael.frysinger@analog.com>
Signed-off-by: Bryan Wu <bryan.wu@analog.com>
Mike Frysinger [Sun, 5 Aug 2007 09:03:59 +0000 (17:03 +0800)]
Blackfin arch: allow people to select the feature that is unavailable to the kernel
- allow people to select the feature that is unavailable to the kernel: NMI, JTAG, or CYCLES.
- change default NMI handler to simply dump hardware trace buffer.
- remove default NMI handler completely as calling into kernel code is not safe
move example handler to wiki so people dont haphazardly copy and paste this stuff thinking its safe
Signed-off-by: Mike Frysinger <michael.frysinger@analog.com>
Signed-off-by: Bryan Wu <bryan.wu@analog.com>
Mike Frysinger [Sun, 5 Aug 2007 08:53:10 +0000 (16:53 +0800)]
Blackfin arch: make sure to stub out ANOMALY_05000230 were appropriate
Signed-off-by: Mike Frysinger <michael.frysinger@analog.com>
Signed-off-by: Bryan Wu <bryan.wu@analog.com>
Jie Zhang [Sun, 5 Aug 2007 08:25:23 +0000 (16:25 +0800)] 
Blackfin arch: Allow ptrace access the fixed code.
Signed-off-by: Jie Zhang <jie.zhang@analog.com>
Signed-off-by: Bryan Wu <bryan.wu@analog.com>
Sonic Zhang [Sun, 5 Aug 2007 08:14:58 +0000 (16:14 +0800)]
Blackfin arch: Add DMA API to set curr descriptor address
This API is necessary for DMA descriptor array mode.
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Bryan Wu <bryan.wu@analog.com>
Bryan Wu [Sun, 5 Aug 2007 07:31:16 +0000 (15:31 +0800)]
Blackfin arch: kill ezkit548 compiling warning
kill ezkit548 compiling warning:
- include/asm/cplb.h:42:5: warning: "ANOMALY_05000158" is not defined
Signed-off-by: Bryan Wu <bryan.wu@analog.com>
Mike Frysinger [Sun, 5 Aug 2007 06:06:16 +0000 (14:06 +0800)]
Blackfin arch: update BOOT_LOAD
update BOOT_LOAD help to reflect current state of the first 4k of
our address space as well as add a memory range option to prevent
invalid values
Signed-off-by: Mike Frysinger <michael.frysinger@analog.com>
Signed-off-by: Bryan Wu <bryan.wu@analog.com>
Robin Getz [Sun, 5 Aug 2007 06:14:42 +0000 (14:14 +0800)]
Blackfin arch: fix up header for BF533
Signed-off-by: Robin Getz <robin.getz@analog.com>
Signed-off-by: Bryan Wu <bryan.wu@analog.com>
Mike Frysinger [Sun, 5 Aug 2007 06:00:11 +0000 (14:00 +0800)]
Blackfin arch: remove spurious KERN_EMERG log level in output
Signed-off-by: Mike Frysinger <michael.frysinger@analog.com>
Signed-off-by: Bryan Wu <bryan.wu@analog.com>
Michael Hennerich [Mon, 27 Aug 2007 07:29:35 +0000 (15:29 +0800)]
Blackfin arch: bug fixing restore mach dependent ASYNC memory size
Bug: When SMC921X driver is enabled, kernel boot crash on EZKIT548
http://blackfin.uclinux.org/gf/project/uclinux-dist/tracker/?action=TrackerItemEdit&tracker_item_id=3460
Fixed by restoring mach dependent ASYNC memory size CPLB coverage.
Once we have a more dynamic memory layout we should come up with a better
solution for these hard-coded values.
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Bryan Wu <bryan.wu@analog.com>
Robin Getz [Wed, 10 Oct 2007 15:55:26 +0000 (23:55 +0800)]
Blackfin arch: to do some consolidation of common code and common name spaces
now all BLKFIN should be BFIN, should be no functional changes.
Signed-off-by: Robin Getz <robin.getz@analog.com>
Signed-off-by: Bryan Wu <bryan.wu@analog.com>
Mike Frysinger [Fri, 3 Aug 2007 10:29:15 +0000 (18:29 +0800)]
Blackfin arch: remove unused code -- EVT0 is not controllable by software
Signed-off-by: Mike Frysinger <michael.frysinger@analog.com>
Signed-off-by: Bryan Wu <bryan.wu@analog.com>
Michael Hennerich [Fri, 3 Aug 2007 09:43:29 +0000 (17:43 +0800)]
Blackfin arch: Add option to priorize DMA over Core
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Bryan Wu <bryan.wu@analog.com>
Michael Hennerich [Sun, 5 Aug 2007 10:55:30 +0000 (18:55 +0800)]
Blackfin arch: Add support for the M25P16 SPI FLash
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Bryan Wu <bryan.wu@analog.com>
Roy Huang [Wed, 10 Oct 2007 15:31:19 +0000 (23:31 +0800)] 
Blackfin arch: add set_dma_curr_addr DMA API to support sound driver recording function
Signed-off-by: Roy Huang <roy.huang@analog.com>
Signed-off-by: Bryan Wu <bryan.wu@analog.com>
Robin Getz [Wed, 25 Jul 2007 03:03:28 +0000 (11:03 +0800)]
Blackfin arch: Add ability to expend the hardware trace buffer
Add ability to expend the hardware trace buffer via a configurable
software buffer - so you can have lots of history when a crash occurs.
The interesting way we do printk in the traps.c confusese the checking
script
Signed-off-by: Robin Getz <robin.getz@analog.com>
Signed-off-by: Bryan Wu <bryan.wu@analog.com>
Robin Getz [Fri, 3 Aug 2007 10:07:17 +0000 (18:07 +0800)]
Blackfin arch: Fix CCLK and SCLK checks
Fix CCLK and SCLK checks, combine all arch checks into one file
for maintance. Checkins that remove more lines than they add are always
good.
Signed-off-by: Robin Getz <robin.getz@analog.com>
Signed-off-by: Bryan Wu <bryan.wu@analog.com>
Michael Hennerich [Thu, 11 Oct 2007 02:57:54 +0000 (10:57 +0800)]
Blackfin serial driver: use new GPIO API
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Bryan Wu <bryan.wu@analog.com>
Michael Hennerich [Fri, 3 Aug 2007 09:48:09 +0000 (17:48 +0800)]
Blackfin arch: Some cosmetics based on LKML feedback from Joe Perches
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Cc: Joe Perches <joe@perches.com>
Signed-off-by: Bryan Wu <bryan.wu@analog.com>
Mike Frysinger [Wed, 25 Jul 2007 03:50:42 +0000 (11:50 +0800)]
Blackfin arch: scrub remaining ASSEMBLY usage since the switch to __ASSEMBLY__
Signed-off-by: Mike Frysinger <michael.frysinger@analog.com>
Signed-off-by: Bryan Wu <bryan.wu@analog.com>
Michael Hennerich [Tue, 24 Jul 2007 10:03:45 +0000 (18:03 +0800)]
Blackfin arch: add missing gpio error handling to make sure we roll back requests in case one fails
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Bryan Wu <bryan.wu@analog.com>
Michael Hennerich [Mon, 27 Aug 2007 08:57:55 +0000 (16:57 +0800)]
Blackfin arch: Fix define - SPORT0_DTPRI is first function
Sigend-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Bryan Wu <bryan.wu@analog.com>
Bryan Wu [Sun, 5 Aug 2007 07:43:03 +0000 (15:43 +0800)]
Blackfin arch: fix bugs report by Andy Liu <yjhsou@gmail.com>, AD1836 can't be probed in BF561-EZ
Cc: Andy Liu <yjhsou@gmail.com>
Signed-off-by: Bryan Wu <bryan.wu@analog.com>
Bryan Wu [Wed, 25 Jul 2007 06:42:03 +0000 (14:42 +0800)]
Blackfin arch: bug fixing, add missing BF533_FAMILY GPIO_PFx definition
Signed-off-by: Bryan Wu <bryan.wu@analog.com>
Michael Hennerich [Tue, 24 Jul 2007 08:27:25 +0000 (16:27 +0800)]
Blackfin arch: Add PORT_J.High (needed for BF548-EZkit Touchscreen interrupts) - remove PORT_C.H
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Bryan Wu <bryan.wu@analog.com>
Michael Hennerich [Tue, 24 Jul 2007 07:16:59 +0000 (15:16 +0800)]
Blackfin arch: Add label to call new GPIO API
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Bryan Wu <bryan.wu@analog.com>
Michael Hennerich [Wed, 10 Oct 2007 14:55:30 +0000 (22:55 +0800)]
Blackfin arch: store labels so we later know who allocated GPIO/Peripheral resources
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Bryan Wu <bryan.wu@analog.com>
Michael Hennerich [Tue, 24 Jul 2007 07:46:36 +0000 (15:46 +0800)]
Blackfin arch: Advertise GENERIC_GPIO and remove duplicated GENERIC_CALIBRATE_DELAY
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Bryan Wu <bryan.wu@analog.com>
Michael Hennerich [Tue, 24 Jul 2007 07:35:53 +0000 (15:35 +0800)]
Blackfin arch: Finalize the generic gpio support - add gpio_to_irq and irq_to_gpio
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Bryan Wu <bryan.wu@analog.com>
Mike Frysinger [Sun, 5 Aug 2007 09:32:25 +0000 (17:32 +0800)]
Blackfin arch: update to latest anomaly sheets
Signed-off-by: Mike Frysinger <michael.frysinger@analog.com>
Signed-off-by: Bryan Wu <bryan.wu@analog.com>
Robin Getz [Fri, 3 Aug 2007 09:56:29 +0000 (17:56 +0800)]
Blackfin arch: Fix Anomaly hanlding, as pointed out by Mike
Signed-off-by: Robin Getz <robin.getz@analog.com>
Cc: Mike Frysinger <michael.frysinger@analog.com>
Signed-off-by: Bryan Wu <bryan.wu@analog.com>
Mike Frysinger [Fri, 3 Aug 2007 08:48:13 +0000 (16:48 +0800)]
Blackfin arch: fix typo... we want csync in CSYNC(), not ssync
Signed-off-by: Mike Frysinger <michael.frysinger@analog.com>
Signed-off-by: Bryan Wu <bryan.wu@analog.com>
Mike Frysinger [Wed, 25 Jul 2007 02:11:42 +0000 (10:11 +0800)]
Blackfin arch: use HI/LO macros rather than masking the bit ranges ourselves
Signed-off-by: Mike Frysinger <michael.frysinger@analog.com>
Signed-off-by: Bryan Wu <bryan.wu@analog.com>
Mike Frysinger [Wed, 25 Jul 2007 04:01:19 +0000 (12:01 +0800)]
Blackfin arch: reorganize headers slightly so we can be sure things are defined early enough
Signed-off-by: Mike Frysinger <michael.frysinger@analog.com>
Signed-off-by: Bryan Wu <bryan.wu@analog.com>
Mike Frysinger [Wed, 25 Jul 2007 03:57:42 +0000 (11:57 +0800)]
Blackfin arch: use the [CS]SYNC() macros which include anomaly workarounds rather than __builtin_bfin_[cs]sync()
Signed-off-by: Mike Frysinger <michael.frysinger@analog.com>
Signed-off-by: Bryan Wu <bryan.wu@analog.com>
Mike Frysinger [Wed, 25 Jul 2007 03:56:01 +0000 (11:56 +0800)]
Blackfin arch: update BF54x anomaly list
Signed-off-by: Mike Frysinger <michael.frysinger@analog.com>
Signed-off-by: Roy Huang <roy.huang@analog.com>
Signed-off-by: Bryan Wu <bryan.wu@analog.com>
Mike Frysinger [Wed, 25 Jul 2007 03:19:14 +0000 (11:19 +0800)]
Blackfin arch: revise anomaly handling by basing things on the compiler not the kconfig defines
revise anomaly handling by basing things on the compiler not the kconfig defines,
so the header is stable and usable outside of the kernel. This also allows us to
move some code from preprocessing to compiling (gcc culls dead code)
which should help with code quality (readability, catch minor bugs, etc...).
Signed-off-by: Mike Frysinger <michael.frysinger@analog.com>
Signed-off-by: Bryan Wu <bryan.wu@analog.com>
Mike Frysinger [Tue, 24 Jul 2007 07:23:20 +0000 (15:23 +0800)]
Blackfin arch: cleanup and standardize anomaly.h file format -- no functional changes
Signed-off-by: Mike Frysinger <michael.frysinger@analog.com>
Signed-off-by: Bryan Wu <bryan.wu@analog.com>
Bryan Wu [Wed, 10 Oct 2007 17:20:06 +0000 (01:20 +0800)]
Blackfin arch: update platform driver resource information to all board files
Signed-off-by: Bryan Wu <bryan.wu@analog.com>
Linus Torvalds [Tue, 9 Oct 2007 20:31:38 +0000 (13:31 -0700)] 
Linux 2.6.23
Linus Torvalds [Tue, 9 Oct 2007 19:38:44 +0000 (12:38 -0700)]
Merge branch 'upstream' of git://ftp.linux-mips.org/upstream-linus
* 'upstream' of git://ftp.linux-mips.org/pub/scm/upstream-linus:
[MIPS] Au1000: set the PCI controller IO base
[MIPS] Alchemy: Fix USB initialization.
[MIPS] IP32: Fix fatal typo in address computation.
Trond Myklebust [Tue, 9 Oct 2007 15:04:57 +0000 (11:04 -0400)] 
NLM: Fix a memory leak in nlmsvc_testlock
The recent fix for a circular lock dependency unfortunately introduced a
potential memory leak in the event where the call to nlmsvc_lookup_host
fails for some reason.
Thanks to Roel Kluin for spotting this.
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Jeff Garzik [Tue, 9 Oct 2007 17:51:57 +0000 (13:51 -0400)] 
sata_mv: correct S/G table limits
The recent mv_fill_sg() rewrite, to fix a data corruption problem
related to IOMMU virtual merging, forgot to account for the
potentially-increased size of the scatter/gather table after its run.
Additionally, the DMA boundary is reduced from 0xffffffff to 0xffff
to more closely match the needs of mv_fill_sg().
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Florian Fainelli [Tue, 25 Sep 2007 15:07:30 +0000 (17:07 +0200)] 
[MIPS] Au1000: set the PCI controller IO base
The PCI controller IO base was not set in the au1000 pci code.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John Crispin <blogic@openwrt.org>
Signed-off-by: Florian Fainelli <florian.fainelli@telecomint.eu>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Florian Fainelli [Tue, 25 Sep 2007 15:07:24 +0000 (17:07 +0200)]
[MIPS] Alchemy: Fix USB initialization.
This patch fixes a wrong ifdef in the board setup code, leading to the GPIO
pin not being pulled high, and thus the USB switch not being powered at all.
This finishes the rename of CONFIG_USB_OHCI to CONFIG_USB_OHCI_HCD, which
started in 2005 (before 2.6.12-rc2), then probably because things were
working anyway for most people got forgotten.
[Ralf: Paolo's original patch didn't fix the module case, Florian's patch
only fixed MTX1 etc. so this is a combined patch plus some cleanups.]
Cc: Giuseppe Patanè <giuseppe.patane@tvblob.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John Crispin <blogic@openwrt.org>
Signed-off-by: Florian Fainelli <florian.fainelli@telecomint.eu>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Giuseppe Sacco [Sat, 6 Oct 2007 17:55:03 +0000 (19:55 +0200)] 
[MIPS] IP32: Fix fatal typo in address computation.
Signed-off-by: Giuseppe Sacco <eppesuig@debian.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Maarten Bressers [Mon, 8 Oct 2007 22:59:13 +0000 (15:59 -0700)] 
Correct Makefile rule for generating custom keymap
When building a custom keymap, after setting GENERATE_KEYMAP := 1 in
drivers/char/Makefile, the kernel build fails like this:
CC drivers/char/vt.o
make[2]: *** No rule to make target `drivers/char/%.map', needed by `drivers/char/defkeymap.c'. Stop.
make[1]: *** [drivers/char] Error 2
make: *** [drivers] Error 2
This was caused by commit
af8b128719f5248e542036ea994610a29d0642a6, which
deleted a necessary colon from the Makefile rule that generates the keymap,
since that rule contains both a target and a target-pattern. The following
patch puts the colon back:
Signed-off-by: Maarten Bressers <mbres@gentoo.org>
Cc: Yoichi Yuasa <yoichi_yuasa@tripeaks.co.jp>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Karsten Keil [Mon, 8 Oct 2007 10:52:09 +0000 (12:52 +0200)] 
ISDN: Fix data access out of array bounds
Fix against access random data bytes outside the dev->chanmap array.
Thanks to Oliver Neukum for pointing me to this issue.
Signed-off-by: Karsten Keil <kkeil@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Mon, 8 Oct 2007 19:59:10 +0000 (12:59 -0700)]
Merge branch 'master' of /linux/kernel/git/davem/net-2.6
* 'master' of master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6:
[IPv6]: Fix ICMPv6 redirect handling with target multicast address
[PKT_SCHED] cls_u32: error code isn't been propogated properly
[ROSE]: Fix rose.ko oops on unload
[TCP]: Fix fastpath_cnt_hint when GSO skb is partially ACKed
Yan Zheng [Mon, 8 Oct 2007 19:16:20 +0000 (12:16 -0700)] 
AIO: fix cleanup in io_submit_one(...)
When IOCB_FLAG_RESFD flag is set and iocb->aio_resfd is incorrect,
statement 'goto out_put_req' is executed. At label 'out_put_req',
aio_put_req(..) is called, which requires 'req->ki_filp' set.
Signed-off-by: Yan Zheng<yanzheng@21cn.com>
Cc: Zach Brown <zach.brown@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Yan Zheng [Mon, 8 Oct 2007 17:08:37 +0000 (10:08 -0700)]
fix page release issue in filemap_fault
find_lock_page increases page's usage count, we should decrease it
before return VM_FAULT_SIGBUS
Signed-off-by: Yan Zheng<yanzheng@21cn.com>
Cc: Nick Piggin <nickpiggin@yahoo.com.au>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Yan Zheng [Mon, 8 Oct 2007 17:05:48 +0000 (10:05 -0700)]
fix VM_CAN_NONLINEAR check in sys_remap_file_pages
The test for VM_CAN_NONLINEAR always fails
Signed-off-by: Yan Zheng<yanzheng@21cn.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Peter Zijlstra [Mon, 8 Oct 2007 16:54:37 +0000 (18:54 +0200)] 
mm: set_page_dirty_balance() vs ->page_mkwrite()
All the current page_mkwrite() implementations also set the page dirty. Which
results in the set_page_dirty_balance() call to _not_ call balance, because the
page is already found dirty.
This allows us to dirty a _lot_ of pages without ever hitting
balance_dirty_pages(). Not good (tm).
Force a balance call if ->page_mkwrite() was successful.
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Brian Haley [Mon, 8 Oct 2007 07:12:05 +0000 (00:12 -0700)] 
[IPv6]: Fix ICMPv6 redirect handling with target multicast address
When the ICMPv6 Target address is multicast, Linux processes the
redirect instead of dropping it. The problem is in this code in
ndisc_redirect_rcv():
if (ipv6_addr_equal(dest, target)) {
on_link = 1;
} else if (!(ipv6_addr_type(target) & IPV6_ADDR_LINKLOCAL)) {
ND_PRINTK2(KERN_WARNING
"ICMPv6 Redirect: target address is not
link-local.\n");
return;
}
This second check will succeed if the Target address is, for example,
FF02::1 because it has link-local scope. Instead, it should be checking
if it's a unicast link-local address, as stated in RFC 2461/4861 Section
8.1:
- The ICMP Target Address is either a link-local address (when
redirected to a router) or the same as the ICMP Destination
Address (when redirected to the on-link destination).
I know this doesn't explicitly say unicast link-local address, but it's
implied.
This bug is preventing Linux kernels from achieving IPv6 Logo Phase II
certification because of a recent error that was found in the TAHI test
suite - Neighbor Disovery suite test 206 (v6LC.2.3.6_G) had the
multicast address in the Destination field instead of Target field, so
we were passing the test. This won't be the case anymore.
The patch below fixes this problem, and also fixes ndisc_send_redirect()
to not send an invalid redirect with a multicast address in the Target
field. I re-ran the TAHI Neighbor Discovery section to make sure Linux
passes all 245 tests now.
Signed-off-by: Brian Haley <brian.haley@hp.com>
Acked-by: David L Stevens <dlstevens@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Stephen Hemminger [Mon, 8 Oct 2007 06:57:45 +0000 (23:57 -0700)] 
[PKT_SCHED] cls_u32: error code isn't been propogated properly
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Alexey Dobriyan [Mon, 8 Oct 2007 06:44:17 +0000 (23:44 -0700)] 
[ROSE]: Fix rose.ko oops on unload
Commit
a3d384029aa304f8f3f5355d35f0ae274454f7cd aka
"[AX.25]: Fix unchecked rose_add_loopback_neigh uses"
transformed rose_loopback_neigh var into statically allocated one.
However, on unload it will be kfree's which can't work.
Steps to reproduce:
modprobe rose
rmmod rose
BUG: unable to handle kernel NULL pointer dereference at virtual address
00000008
printing eip:
c014c664
*pde =
00000000
Oops: 0000 [#1]
PREEMPT DEBUG_PAGEALLOC
Modules linked in: rose ax25 fan ufs loop usbhid rtc snd_intel8x0 snd_ac97_codec ehci_hcd ac97_bus uhci_hcd thermal usbcore button processor evdev sr_mod cdrom
CPU: 0
EIP: 0060:[<
c014c664>] Not tainted VLI
EFLAGS:
00210086 (2.6.23-rc9 #3)
EIP is at kfree+0x48/0xa1
eax:
00000556 ebx:
c1734aa0 ecx:
f6a5e000 edx:
f7082000
esi:
00000000 edi:
f9a55d20 ebp:
00200287 esp:
f6a5ef28
ds: 007b es: 007b fs: 0000 gs: 0033 ss: 0068
Process rmmod (pid: 1823, ti=
f6a5e000 task=
f7082000 task.ti=
f6a5e000)
Stack:
f9a55d20 f9a5200c 00000000 00000000 00000000 f6a5e000 f9a5200c f9a55a00
00000000 bf818cf0 f9a51f3f f9a55a00 00000000 c0132c60 65736f72 00000000
f69f9630 f69f9528 c014244a f6a4e900 00200246 f7082000 c01025e6 00000000
Call Trace:
[<
f9a5200c>] rose_rt_free+0x1d/0x49 [rose]
[<
f9a5200c>] rose_rt_free+0x1d/0x49 [rose]
[<
f9a51f3f>] rose_exit+0x4c/0xd5 [rose]
[<
c0132c60>] sys_delete_module+0x15e/0x186
[<
c014244a>] remove_vma+0x40/0x45
[<
c01025e6>] sysenter_past_esp+0x8f/0x99
[<
c012bacf>] trace_hardirqs_on+0x118/0x13b
[<
c01025b6>] sysenter_past_esp+0x5f/0x99
=======================
Code: 05 03 1d 80 db 5b c0 8b 03 25 00 40 02 00 3d 00 40 02 00 75 03 8b 5b 0c 8b 73 10 8b 44 24 18 89 44 24 04 9c 5d fa e8 77 df fd ff <8b> 56 08 89 f8 e8 84 f4 fd ff e8 bd 32 06 00 3b 5c 86 60 75 0f
EIP: [<
c014c664>] kfree+0x48/0xa1 SS:ESP 0068:
f6a5ef28
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ilpo Järvinen [Mon, 8 Oct 2007 06:43:10 +0000 (23:43 -0700)] 
[TCP]: Fix fastpath_cnt_hint when GSO skb is partially ACKed
When only GSO skb was partially ACKed, no hints are reset,
therefore fastpath_cnt_hint must be tweaked too or else it can
corrupt fackets_out. The corruption to occur, one must have
non-trivial ACK/SACK sequence, so this bug is not very often
that harmful. There's a fackets_out state reset in TCP because
fackets_out is known to be inaccurate and that fixes the issue
eventually anyway.
In case there was also at least one skb that got fully ACKed,
the fastpath_skb_hint is set to NULL which causes a recount for
fastpath_cnt_hint (the old value won't be accessed anymore),
thus it can safely be decremented without additional checking.
Reported by Cedric Le Goater <clg@fr.ibm.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
Dmitry Torokhov [Sun, 7 Oct 2007 16:22:21 +0000 (12:22 -0400)] 
Driver core: fix SYSF_DEPRECATED breakage for nested classdevs
We should only reparent to a class former class devices that
form the base of class hierarchy. Nested devices should still
grow from their real parents.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Tested-by: Andrey Borzenkov <arvidjaar@mail.ru>
Tested-by: Anssi Hannula <anssi.hannula@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Sun, 7 Oct 2007 23:41:09 +0000 (16:41 -0700)]
Merge branch 'for-linus' of git://git./linux/kernel/git/ieee1394/linux1394-2.6
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ieee1394/linux1394-2.6:
firewire: point to migration document
Attila Kinali [Sun, 7 Oct 2007 07:24:38 +0000 (00:24 -0700)] 
Add manufacturer and card id of teltonica pcmcia modems
Add the manufacturer and card id of teltonica pcmcia modems to serial_cs.c
Signed-off-by: Attila Kinali <attila@kinali.ch>
Acked-by: Alan Cox <alan@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pavel Machek [Sun, 7 Oct 2007 07:24:37 +0000 (00:24 -0700)] 
sysrq docs: document sequence that actually works
Document sequence of keypresses that actually works. Yes, this changed
year-or-so ago.
Signed-off-by: Pavel Machek <pavel@suse.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Al Viro [Sun, 7 Oct 2007 07:24:36 +0000 (00:24 -0700)] 
fix bogus reporting of signals by audit
Async signals should not be reported as sent by current in audit log. As
it is, we call audit_signal_info() too early in check_kill_permission().
Note that check_kill_permission() has that test already - it needs to know
if it should apply current-based permission checks. So the solution is to
move the call of audit_signal_info() between those.
Bogosity in question is easily reproduced - add a rule watching for e.g.
kill(2) from specific process (so that audit_signal_info() would not
short-circuit to nothing), say load_policy, watch the bogus OBJ_PID entry
in audit logs claiming that write(2) on selinuxfs file issued by
load_policy(8) had somehow managed to send a signal to syslogd...
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Acked-by: Steve Grubb <sgrubb@redhat.com>
Acked-by: Eric Paris <eparis@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Alexey Dobriyan [Sun, 7 Oct 2007 07:24:34 +0000 (00:24 -0700)] 
Move kasprintf.o to obj-y
Modulat lguest started giving linking errors
MODPOST 1 modules
ERROR: "kasprintf" [drivers/lguest/lg.ko] undefined!
Signed-off-by: Alexey Dobriyan <adobriyan@sw.ru>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Peter Zijlstra [Sun, 7 Oct 2007 07:24:33 +0000 (00:24 -0700)] 
lockstat: documentation
Provide some documentation for CONFIG_LOCK_STAT.
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Acked-by: Ingo Molnar <mingo@elte.hu>
Cc: "Randy.Dunlap" <rdunlap@xenotime.net>
Cc: Rob Landley <rob@landley.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Rafal Bilski [Sun, 7 Oct 2007 07:24:32 +0000 (00:24 -0700)] 
Longhaul: add auto enabled "revid_errata" option
VIA C3 Ezra-T has RevisionID equal to 1, but it needs RevisionKey to be 0
or CPU will ignore new frequency and will continue to work at old
frequency. New "revid_errata" option will force RevisionKey to be set to
0, whatever RevisionID is.
Additionaly "Longhaul" will not silently ignore unsuccessful transition.
It will try to check if "revid_errata" or "disable_acpi_c3" options need to
be enabled for this processor/system.
Same for Longhaul ver. 2 support. It will be disabled if none of above
options will work.
Best case scenario (with patch apllied and v2 enabled):
longhaul: VIA C3 'Ezra' [C5C] CPU detected. Longhaul v2 supported.
longhaul: Using northbridge support.
longhaul: VRM 8.5
longhaul: Max VID=1.350 Min VID=1.050, 13 possible voltage scales
longhaul: f: 300000 kHz, index: 0, vid: 1050 mV
[...]
longhaul: Voltage scaling enabled.
Worst case scenario:
longhaul: VIA C3 'Ezra-T' [C5M] CPU detected. Powersaver supported.
longhaul: Using northbridge support.
longhaul: Using ACPI support.
longhaul: VRM 8.5
longhaul: Claims to support voltage scaling but min & max are both 1.250. Voltage scaling disabled
longhaul: Failed to set requested frequency!
longhaul: Enabling "Ignore Revision ID" option.
longhaul: Failed to set requested frequency!
longhaul: Disabling ACPI C3 support.
longhaul: Disabling "Ignore Revision ID" option.
longhaul: Failed to set requested frequency!
longhaul: Enabling "Ignore Revision ID" option.
[akpm@linux-foundation.org: coding-style cleanups]
Signed-off-by: Rafal Bilski <rafalbilski@interia.pl>
Signed-off-by: Dave Jones <davej@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Anton Blanchard [Sun, 7 Oct 2007 07:24:31 +0000 (00:24 -0700)] 
Fix timer_stats printout of events/sec
When using /proc/timer_stats on ppc64 I noticed the events/sec field wasnt
accurate. Sometimes the integer part was incorrect due to rounding (we
werent taking the fractional seconds into consideration).
The fraction part is also wrong, we need to pad the printf statement and
take the bottom three digits of 1000 times the value.
Signed-off-by: Anton Blanchard <anton@samba.org>
Acked-by: Ingo Molnar <mingo@elte.hu>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Sun, 7 Oct 2007 23:17:38 +0000 (16:17 -0700)]
Don't do load-average calculations at even 5-second intervals
It turns out that there are a few other five-second timers in the
kernel, and if the timers get in sync, the load-average can get
artificially inflated by events that just happen to coincide.
So just offset the load average calculation it by a timer tick.
Noticed by Anders Boström, for whom the coincidence started triggering
on one of his machines with the JBD jiffies rounding code (JBD is one of
the subsystems that also end up using a 5-second timer by default).
Tested-by: Anders Boström <anders@bostrom.dyndns.org>
Cc: Chuck Ebbert <cebbert@redhat.com>
Cc: Arjan van de Ven <arjan@linux.intel.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Sun, 7 Oct 2007 23:02:55 +0000 (16:02 -0700)]
VT_WAITACTIVE: Avoid returning EINTR when not necessary
We should generally prefer to return ERESTARTNOHAND rather than EINTR,
so that processes with unhandled signals that get ignored don't return
EINTR.
This can help with X startup issues:
Fatal server error:
xf86OpenConsole: VT_WAITACTIVE failed: Interrupted system call
although the real fix is having the X server always retry EINTR
regardless (since EINTR does happen for signals that have handlers
installed). Keithp has a patch for that.
Regardless, ERESTARTNOHAND is the correct thing to use.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Stefan Richter [Sun, 7 Oct 2007 10:31:22 +0000 (12:31 +0200)] 
firewire: point to migration document
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Linus Torvalds [Sat, 6 Oct 2007 22:47:16 +0000 (15:47 -0700)]
Merge branch 'upstream' of git://ftp.linux-mips.org/upstream-linus
* 'upstream' of git://ftp.linux-mips.org/pub/scm/upstream-linus:
[MIPS] IP32: Enable PCI bridges
Kyle McMartin [Sat, 6 Oct 2007 05:42:34 +0000 (01:42 -0400)] 
Revert "intel_agp: fix stolen mem range on G33"
This reverts commit
f443675affe3f16dd428e46f0f7fd3f4d703eeab, which
breaks horribly if you aren't running an unreleased xf86-video-intel
driver out of git.
Signed-off-by: Kyle McMartin <kyle@mcmartin.ca>
Cc: Dave Airlie <airlied@linux.ie>
Cc: Zhenyu Wang <zhenyu.z.wang@intel.com>
Acked-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Benjamin Herrenschmidt [Sat, 6 Oct 2007 08:52:27 +0000 (18:52 +1000)] 
Fix non-terminated PCI match table in PowerMac IDE
The PCI device table in the powermac IDE driver isn't properly
terminated. Depending on how your kernel is linked and other random
factors, you can end up with this driver matched against any other PCI
device in your system, possibly crashing at boot.
Thanks to Heikki for tracking this down with me, the bug have been there
for some time, though it rarely hurts due to luck. In this case, the
switch from .22 to .23-rc9 is causing it to show up due to differences
in the resulting layout of .data I suppose.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <pmac@au1.ibm.com>
Cc: Bartlomiej Zolnierkiewicz <B.Zolnierkiewicz@elka.pw.edu.pl>
Cc: Heikki Lindholm <holindho@cs.helsinki.fi>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Jeremy Fitzhardinge [Sat, 6 Oct 2007 00:19:35 +0000 (17:19 -0700)] 
xen: disable split pte locks for now
When pinning and unpinning pagetables, we must protect them against
being used by other CPUs, lest they see the pagetable in an
intermediate read-only-but-not-pinned state.
When using split pte locks, doing this properly would require taking
all the pte locks for the pagetable while pinning, but this may overflow
the PREEMPT_BITS part of the preempt counter if the process has mapped
more than about 512M of memory.
However, failing to take the pte locks causes write-protect faults when
the pageout code is trying to clear the Access bit on a pte which is part
of a freshy created and still being pinned process after fork.
This is a short-term fix until the problem is solved properly.
Signed-off-by: Jeremy Fitzhardinge <jeremy@xensource.com>
Acked-by: Rik van Riel <riel@redhat.com>
Acked-by: Hugh Dickins <hugh@veritas.com>
Cc: David Rientjes <rientjes@google.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Andi Kleen <ak@suse.de>
Cc: Keir Fraser <keir@xensource.com>
Cc: Jan Beulich <jbeulich@novell.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Fri, 5 Oct 2007 21:09:10 +0000 (14:09 -0700)]
Merge master.kernel.org:/home/rmk/linux-2.6-arm
* master.kernel.org:/home/rmk/linux-2.6-arm:
[ARM] 4598/2: OSIRIS: Ensure we do not get nRSTOUT during suspend
[ARM] 4597/2: OSIRIS: ensure CPLD0 is preserved after suspend
projects / linux-2.6 / log
