V4L/DVB (6963): tda18271: store IF frequency in a u16 instead of u32

Store IF Frequency in a u16 instead of a u32.  Multiply by 1000 before use.

Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>

V4L/DVB (6962): tda18271: allow device-specific configuration of IF frequency and std bits

Allow drivers to pass device-specific configuration parameters during attach.

If these parameters are omitted, default values will be used.

Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>

V4L/DVB (6961): tda18271: move common code to tda18271-common.c

Move some common code to a new file to make this easier to look at.

Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>

V4L/DVB (6960): tda18271: add support for NXP TDA18271HD/C2

Tested successfully with QAM256 digital cable.
Analog television is limping, needs more work.

Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>

V4L/DVB (6959): tda18271: add MODULE_VERSION

version 0.1

Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>

V4L/DVB (6958): tda18271: clean up function tda18271_set_analog_params

make set_analog_params function look consistent with set_params function

Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>

V4L/DVB (6957): tda18271: fail table lookups if frequency is out of range

Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>

V4L/DVB (6956): Add Radio support for em28xx

Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>

V4L/DVB (6955): Properly implement 12MHz I2S support

Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>

V4L/DVB (6954): There isn't a MTS radio firmware

Try to load non-MTS firmware instead.

Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>

V4L/DVB (6953): Fix radio set frequency logic

Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>

V4L/DVB (6952): Add code for autoloading em28xx-alsa, if needed

Older em28xx devices does implement standard Audio Class.

However, on newer devices, this were replaced by a Vendor Class. This
patch autodetects that an em28xx lacks Audio Class and auto-loads
em28xx-alsa, for the devices that implements only a Vendor Class.

For devices with Audio Class, snd-usb-audio module will provide an ALSA
interface.

This patch uses the request_module_async function as defined on cx88-mpeg.c,
originally wrote by Markus Rechberger.

Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>

V4L/DVB (6951): Integrates em28xx-audio.c into em28xx kernel module

Also fixes the remaining CodingStyle issues that Lindent didn't fix.

Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>

V4L/DVB (6950): Lindent em28xx-audio.c

Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>

V4L/DVB (6949): Adds em28xx-audio module

em28xx-audio module exports em28xx Vendor Class audio as an -alsa
driver. This module were written based on usbaudio driver by Markus
Rechberger. Recently, he acked to allow us to merge it on kernel:

http://lists-archives.org/video4linux/20408-supporting-prolink-pixelview-405-dvd-maker.html

Thanks to Markus Rechberger <mrechberger@gmail.com>

Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>

V4L/DVB (6948): HVR950 requires additional settings for audio to properly work

Thanks to Markus Rechberger <mrechberger@gmail.com> for retriving those
commands.

Also, MTS firmware is required for audio to work on HVR950.

Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>

V4L/DVB (6947): Improve audio setup handling

It is possible to select audio inputs via em28xx or via ac97 functions.
This patch allows configuring a board to use either one way.

It also do some cleanups at audio setup configurations.

Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>

V4L/DVB (6944): Fix in-kernel ivtv compilation

Due to tuner-xc2028.h, some extra directories should be added at .h search.

Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>

V4L/DVB (6938): Add a tool for extracting xc3028 version 2.7 firmware

This tool allows the extraction of xc3028 v2.7 firmware from HVR 12x0 file.

Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>

V4L/DVB (6936): cx23885: update model matrix for Hauppauge HVR1500

Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>

V4L/DVB (6935): cx23885: add missing subsystem IDs for Hauppauge HVR1500 Retail

Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>

V4L/DVB (6934): cx23885: update model matrix for Hauppauge HVR1250

Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>

V4L/DVB (6933): cx23885: update model matrix for Hauppauge HVR1800

Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>

V4L/DVB (6932): cx23885: add missing subsystem ID for Hauppauge HVR1800 Retail

Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>

V4L/DVB (6930): xc5000: Removed erroneous defines

Basic cleanup.

Signed-off-by: Steven Toth <stoth@hauppauge.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>

V4L/DVB (6928): tda18271: break calculation functions out of tda18271_tune

Break out the following new functions from tda18271_tune:

tda18271_calc_bp_filter
tda18271_calc_km
tda18271_calc_rf_band
tda18271_calc_gain_taper
tda18271_calc_ir_measure
tda18271_calc_rf_cal

Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>

V4L/DVB (6927): tda18271: improve printk macros

Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>

V4L/DVB (6926): tda18271: consolidate table lookup functions

Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>

V4L/DVB (6925): tda18271: move state structures to tda18271-priv.h

Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>

V4L/DVB (6924): tda18271: fix whitespace in tda18271_ir_measure

Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>

V4L/DVB (6923): tda18271: remove extraneous debug

We don't need to do a dbg_info during tda18271_attach anymore, since
the tda18271_get_id function will call dbg_info with the same information
and more.

Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>

V4L/DVB (6921): include/media/v4l2-i2c-drv.h must #include <media/v4l2-common.h>

Fix the following compiler error:

v4l2-i2c-drv.h:72: error: implicit declaration of function 'v4l2_i2c_attach'

Also, prevent multiple inclusions of v4l2-i2c-drv.h

Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>

V4L/DVB (6920): tuner: fix backwards logic in check for set_config

tuner-core was checking if analog_ops->set_config is set.  If set, it would
complain that it isn't.  Fix this backwards logic to the proper behavior.

Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>

V4L/DVB (6919): Kconfig: VIDEO_CX23885 must select DVB_TUNER_XC5000 if !DVB_FE_CUSTOMIZE

Everybody forgets to add the Kconfig stuff after they add new card support :-/

Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>

V4L/DVB (6917): ivtv: small textual update

Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>

V4L/DVB (6915): ivtv: drop an incorrect comment

Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>

V4L/DVB (6914): Fix a few issues at the bttv conversion

bttv driver is working as previously. An additional gain of about 1,5Kb were
obtained with the driver conversion to vidioc_ioctl2:

   text    data     bss     dec     hex filename
  89208   40244   57556  187008   2da80 old/bttv.ko
  88960   38740   57556  185256   2d3a8 new/bttv.ko

(measured on a x86_64)

Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>

V4L/DVB (6913): Preserve the previous order to make easier to check the conversion

Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>

V4L/DVB (6912): Replace vidioc_ to bttv_

Since there are a few vidioc_ functions that were exported, rename those
functions to bttv_ in order to avoid poluting namespace.

The other functions were also renamed, to standardize inside the driver.

Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>

V4L/DVB (6911): Converted bttv to use video_ioctl2

Signed-off-by: Douglas Schilling Landgraf <dougsland@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>

V4L/DVB (6909): cx23885: fix bad use count caused by tda18271 being probed by tda8290

Don't allow the tda8290 module to probe and attach the tuner module,
causing incorrect use counts when using dvb_attach.

Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>

V4L/DVB (6908): tda8290: add the option not to probe for tuners passed into tda829x_config

Prevent the tda8290 module from probing for tuners during tda829x_attach,
by passing:

.probe_tuner = TDA829X_DONT_PROBE,

...in struct tda829x_config

Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>

V4L/DVB (6907): tda18271: create separate calc_pll functions

Consolidate duplicated code by creating functions:

tda18271_calc_main_pll
tda18271_calc_cal_pll

Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>

V4L/DVB (6906): tda18271: rename tda18271_calc_* functions to tda18271_lookup_*

Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>

V4L/DVB (6905): tda18271: check ID register during attach

Identify the silicon during attach, return NULL if unsupported device.

Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>

V4L/DVB (6904): tda18271: divider byte 1, bit 7 is always 0

Bit 7 of both Main Divider byte 1 and Cal Divider byte 1 is always zero.

Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>

V4L/DVB (6903): mt312: CodingStyle fix

Fixes all occurences of assignment in if

checkpatch marks them as ERROR.

Signed-off-by: Matthias Schwarzott <zzam@gentoo.org>
Reviewed-by: Andreas Oberritter <obi@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>

V4L/DVB (6901): Kconfig: VIDEO_CX23885 selects TUNER_TDA8290 and DVB_TDA18271

Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>

V4L/DVB (6900): cx23885: enable EZ-QAM mode for Hauppauge WinTV HVR-1800

Add module option 'alt_tuner' disabled by default.

When set to one, the dvb_frontend of HVR1800 will consist of:
s5h1409 demod + tda18271 tuner

When set zero (default), the dvb_frontend of HVR1800 will consist of:
s5h1409 demod + mt2131 tuner

If the tda18271 is used in digital mode, you will not be able to
tune an analog channel at the same time.

Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>

V4L/DVB (6899): Kconfig: VIDEO_CX23885 must select TUNER_XC2028 if !DVB_FE_CUSTOMIZE

Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>

V4L/DVB (6898): cx23885: add support for Hauppauge WinTV HVR-1500

Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>

V4L/DVB (6897): xc2028: ignore HAS_IF during specific S-Code type searches

If we are selecting the S-Code firmware to load by name, then we must mask
off the HAS_IF bit during the search.

Signed-off-by: Chris Pascoe <c.pascoe@itee.uq.edu.au>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>

V4L/DVB (6896): ivtv: add XC2028 support for Club3D cards

Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>

V4L/DVB (6894): xc5000: fix build warning

Fix the following build warning:

xc5000.c:560: warning: format '%d' expects type 'int',
      but argument 2 has type 'size_t'

On many architectrues size_t is unsigned long, and may not be printed with %d.
Use %Zu instead.

Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>

V4L/DVB (6893): tuner-xc2028: fix xc2028_attach function

xc2028_attach was returning an integer when disabled from the build, where it
should instead be returning NULL.  Declare xc2028_attach as type dvb_frontend *
instead of void *.

The prototype declaration must be marked as extern in the header.

Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>

V4L/DVB (6892): xc5000: fix build when DVB_TUNER_XC5000 is disabled

Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>

V4L/DVB (6890): tda18271: fix typo in RF tracking filter calibration

We want to set bits 1 & 2 on easy programming byte 4, not extended byte 4.

Thanks to David Wong for pointing this out.

Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Cc: David Wong <davidtlwong@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>

V4L/DVB (6888): Add Hauppauge tuner type 150 defintion

Add Hauppauge tuner type 150 defintion.

Signed-off-by: Steven Toth <stoth@hauppauge.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>

V4L/DVB (6887): Avoid 'unknown model' message for the HVR1500-Q

Avoid 'unknown model' message for the HVR1500-Q

Signed-off-by: Steven Toth <stoth@hauppauge.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>

V4L/DVB (6886): xc5000: Cleanups of types, result codes etc

This translates much of the xceive coding style, adds
some result codes and generally cleans up whitespace
and function arguments.

Signed-off-by: Steven Toth <stoth@hauppauge.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>

V4L/DVB (6885): Add support for the Hauppauge HVR1500Q

The express card ATSC/QAM tuner.

Signed-off-by: Steven Toth <stoth@hauppauge.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>

V4L/DVB (6884): Add support for the Xceive xc5000 silicon tuner

This is an all formats tuner, QAM, ATSC, DVB-T and others.
Only ATSC and QAM have been tested.

Signed-off-by: Steven Toth <stoth@hauppauge.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>

V4L/DVB (6882): dvb_frontend: release analog demod in dvb_frontend_detach

Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>

V4L/DVB (6881): include struct analog_demod_ops directly inside struct dvb_frontend

Rather than using a pointer, include struct analog_demod_ops directly
inside struct dvb_frontend.  This will allow us to use dvb_attach in
the future, along with removing the need to check the ops structure
before having to check the pointer to the method being called.

Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>

V4L/DVB (6880): kill tuner-driver.h

Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>

V4L/DVB (6879): move struct analog_tuner_ops into dvb_frontend.h

struct analog_tuner_ops no longer has any dependencies specific
to v4l2, so we can move this into dvb_frontend.h with the rest
of the tuning structures.

Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>

V4L/DVB (6878): tuner: remove extraneous variable declaration

tuner_count is already declared as "extern unsigned const int"
in <media/tuner-types.h>  -- Remove it from tuner-driver.h

Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>

V4L/DVB (6875): tuner-xc2028: ATSC requires 1.75 MHz tuning offset

In my testing yesterday, I was using a scan file tailored specifically
for a unique test situation -- As it turns out, this scan file was bad,
and I will use the one included inside dvb-apps for testing for now on.

I've tested with other ATSC tuners just to confirm, using:

us-ATSC-center-frequencies-8VSB

Anyhow, as it turns out, the tuner-xc2028 *does* require a tuning offset
for ATSC.  Even though the linux-dvb api passes in center frequencies
from userspace, apparantly the xceive firmware is already factoring in
the tuning offset to center.

In order to make the device function using the same scan files /
channels.conf configurations as other atsc devices, we must offset by
1.75 MHz.

Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>

V4L/DVB (6874): removes duplicated KERN_DEBUG flags from dprintk calls in mt312.c

        do { \
                if (debug) printk(KERN_DEBUG "mt312: " args); \
        } while (0)

So no caller need to specify KERN_DEBUG.

Signed-off-by: Matthias Schwarzott <zzam@gentoo.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>

V4L/DVB (6873): Fixes issues listed by checkpatch

Signed-off-by: Matthias Schwarzott <zzam@gentoo.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>

V4L/DVB (6869): cs5345: new i2c driver

Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>

V4L/DVB (6868): i2c-id.h: add I2C_DRIVERID_CS5345

Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>

V4L/DVB (6867): saa7127: CodingStyle cleanups

Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>

V4L/DVB (6866): msp3400: CodingStyle cleanups

Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>

V4L/DVB (6865): vp27smpx: CodingStyle cleanup

Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>

V4L/DVB (6864): upd64031a: CodingStyle cleanup

Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>

V4L/DVB (6863): upd64083: CodingStyle cleanups

Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>

V4L/DVB (6862): ivtv: really remove i2c legacy support from drivers that no longer need it

For some reason the include header wasn't changed from v4l2-i2c-drv-legacy.h
to v4l2-i2c-drv.h in the previous patch. This is now corrected.

Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>

V4L/DVB (6861): cx2341x: command argument should be u32 instead of int

Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>

V4L/DVB (6860): tveeprom: CodingStyle cleanup

Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>

V4L/DVB (6859): tveeprom: add support for Hauppauge models 74xxx

Thanks to Steve Toth from Hauppauge with providing me with the information
needed to add support for these models.

Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>

V4L/DVB (6858): Fix offset for ATSC

ATSC works with offset=0

Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>

V4L/DVB (6857): cx23885: correctly join I2C writes and reads from same address

When an I2C message specifies a write then a read from the same I2C address,
we need to tell the chip to not release the bus between the message parts.

Signed-off-by: Chris Pascoe <c.pascoe@itee.uq.edu.au>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>

V4L/DVB (6856): zl10353: improve tuning parameters and update register map

Some more I2C traces and a experimentation with register values on
both the ZL10353 and MT352 mean that I can now guess at what more
of the ZL10353 registers do.

Guess at the registers' names (based on the equivalent names in MT352)
and update set_parameters/get_parameters with the new knowledge.

Signed-off-by: Chris Pascoe <c.pascoe@itee.uq.edu.au>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>

V4L/DVB (6855): xc2028: select DTV78 firmware if tuning 7MHz VHF / 8MHz UHF

It seems that the DTV78 firmware is intended for use in locations where
VHF channels have 7MHz bandwidth and UHF channels have 8MHz bandwidth.
If we switch to DTV78 firmware when we detect this condition, we can
avoid firmware reloads when switching between VHF and UHF transponders.

Place the state for this in the control structure so that card drivers
can hint to us to use DTV78 firmware from the first tuning attempt.

Signed-off-by: Chris Pascoe <c.pascoe@itee.uq.edu.au>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>

V4L/DVB (6854): xc2028: be more specific about when applying offset for 7MHz channels

We have been inserting a mystery 500kHz offset for tuning 7MHz channels,
however some experimentation reveals it is only needed under certain
conditions with specific firmware combinations.  Document these and only
apply the offset when we know it is required.

Signed-off-by: Chris Pascoe <c.pascoe@itee.uq.edu.au>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>

V4L/DVB (6853): xc2028: check HAS_IF flag against table

When searching for the right S-Code table to load, check the HAS_IF flag
against the firmware we are checking instead of against the the "type"
requested.  We already ignore the scode type requested if the caller passed
an int_freq; this makes the search by frequency consistent with that behaviour.

Signed-off-by: Chris Pascoe <c.pascoe@itee.uq.edu.au>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>

V4L/DVB (6852): xc2028: s-code offset should not modify internal control structure

Don't modify the control structure that was provided at attach when applying
an offset to the S-Code, otherwise it will be incorrect on subsequent tunes.

Signed-off-by: Chris Pascoe <c.pascoe@itee.uq.edu.au>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>

V4L/DVB (6851): xc2028: include int_freq in firmware version display

Add "int_freq" to the debugging output when selecting firmware and the
HAS_IF flag when dumping firmware during load.

Signed-off-by: Chris Pascoe <c.pascoe@itee.uq.edu.au>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>

V4L/DVB (em28xx): Add support for Pinnacle Dazzle DVC 100

The patch below adds the "Pinnacle Dazzle DVC 100" to the list of
cards supported by the em28xx driver. As the configuration is the same
as the DVC 90 one, it simply adds a new USB ID to the list of devices
supported by the DVC 90 configuration.

Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>

V4L/DVB (6848): bttv: check pci_register_driver() error

Check pci_register_driver() error in module_init.

Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>

V4L/DVB (6846): tda9887: initialize mode to T_STANDBY at startup

Ensure that the audio is muted at attach-time

Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>

V4L/DVB (6845): tuner: remove unneeded #includes from tuner-driver.h

Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>

V4L/DVB (6844): tuner: remove struct tuner from tuner-driver.h

struct tuner holds state for tuner-core, only -- move it into tuner-core.c

Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>

V4L/DVB (6843): tda9887: use printk macros from tuner-i2c.h

replace tda9887_info and tda9887_dbg printk macros with
tuner_info and tuner_dbg, defined in tuner-i2c.h

Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>

V4L/DVB (6842): tda9887: remove dependency on struct tuner

Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>

V4L/DVB (6841): tda9887: maintain private state independent of struct tuner

Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>

V4L/DVB (6840): tuner: convert tda9887 to use TUNER_SET_CONFIG

Use TUNER_SET_CONFIG to set configuration in tda9887's private state
structure, rather than storing tda9887-specific configuration within
struct tuner.

Update handling of TUNER_SET_CONFIG by tuner-core, to call
&t->fe.ops.analog_demod_ops rather than &t->fe.ops.tuner_ops

analog_demod_ops.set_config passes the request to tuner_ops.set_config,
so this does not break other drivers.

Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>

V4L/DVB (6839): tuner: add set_config to struct analog_tuner_ops

Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>

V4L/DVB (6838): tda9887: remove references to struct tuner from printk macros

Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>