Chris Pascoe [Sun, 2 Dec 2007 13:07:06 +0000 (10:07 -0300)] 
V4L/DVB (6855): xc2028: select DTV78 firmware if tuning 7MHz VHF / 8MHz UHF
It seems that the DTV78 firmware is intended for use in locations where
VHF channels have 7MHz bandwidth and UHF channels have 8MHz bandwidth.
If we switch to DTV78 firmware when we detect this condition, we can
avoid firmware reloads when switching between VHF and UHF transponders.
Place the state for this in the control structure so that card drivers
can hint to us to use DTV78 firmware from the first tuning attempt.
Signed-off-by: Chris Pascoe <c.pascoe@itee.uq.edu.au>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Chris Pascoe [Sun, 2 Dec 2007 12:39:18 +0000 (09:39 -0300)]
V4L/DVB (6854): xc2028: be more specific about when applying offset for 7MHz channels
We have been inserting a mystery 500kHz offset for tuning 7MHz channels,
however some experimentation reveals it is only needed under certain
conditions with specific firmware combinations. Document these and only
apply the offset when we know it is required.
Signed-off-by: Chris Pascoe <c.pascoe@itee.uq.edu.au>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Chris Pascoe [Sun, 2 Dec 2007 09:54:17 +0000 (06:54 -0300)]
V4L/DVB (6853): xc2028: check HAS_IF flag against table
When searching for the right S-Code table to load, check the HAS_IF flag
against the firmware we are checking instead of against the the "type"
requested. We already ignore the scode type requested if the caller passed
an int_freq; this makes the search by frequency consistent with that behaviour.
Signed-off-by: Chris Pascoe <c.pascoe@itee.uq.edu.au>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Chris Pascoe [Sun, 2 Dec 2007 09:36:42 +0000 (06:36 -0300)]
V4L/DVB (6852): xc2028: s-code offset should not modify internal control structure
Don't modify the control structure that was provided at attach when applying
an offset to the S-Code, otherwise it will be incorrect on subsequent tunes.
Signed-off-by: Chris Pascoe <c.pascoe@itee.uq.edu.au>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Chris Pascoe [Sun, 2 Dec 2007 09:30:50 +0000 (06:30 -0300)]
V4L/DVB (6851): xc2028: include int_freq in firmware version display
Add "int_freq" to the debugging output when selecting firmware and the
HAS_IF flag when dumping firmware during load.
Signed-off-by: Chris Pascoe <c.pascoe@itee.uq.edu.au>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Aurelien Jarno [Mon, 17 Dec 2007 16:49:17 +0000 (13:49 -0300)] 
V4L/DVB (em28xx): Add support for Pinnacle Dazzle DVC 100
The patch below adds the "Pinnacle Dazzle DVC 100" to the list of
cards supported by the em28xx driver. As the configuration is the same
as the DVC 90 one, it simply adds a new USB ID to the list of devices
supported by the DVC 90 configuration.
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Akinobu Mita [Mon, 17 Dec 2007 17:26:29 +0000 (14:26 -0300)] 
V4L/DVB (6848): bttv: check pci_register_driver() error
Check pci_register_driver() error in module_init.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Michael Krufky [Mon, 17 Dec 2007 12:49:33 +0000 (09:49 -0300)] 
V4L/DVB (6846): tda9887: initialize mode to T_STANDBY at startup
Ensure that the audio is muted at attach-time
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Michael Krufky [Mon, 17 Dec 2007 04:21:08 +0000 (01:21 -0300)]
V4L/DVB (6845): tuner: remove unneeded #includes from tuner-driver.h
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Michael Krufky [Mon, 17 Dec 2007 01:02:26 +0000 (22:02 -0300)]
V4L/DVB (6844): tuner: remove struct tuner from tuner-driver.h
struct tuner holds state for tuner-core, only -- move it into tuner-core.c
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Michael Krufky [Mon, 17 Dec 2007 00:20:21 +0000 (21:20 -0300)]
V4L/DVB (6843): tda9887: use printk macros from tuner-i2c.h
replace tda9887_info and tda9887_dbg printk macros with
tuner_info and tuner_dbg, defined in tuner-i2c.h
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Michael Krufky [Sun, 16 Dec 2007 23:11:46 +0000 (20:11 -0300)]
V4L/DVB (6842): tda9887: remove dependency on struct tuner
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Michael Krufky [Sun, 16 Dec 2007 23:05:00 +0000 (20:05 -0300)]
V4L/DVB (6841): tda9887: maintain private state independent of struct tuner
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Michael Krufky [Sun, 16 Dec 2007 22:53:32 +0000 (19:53 -0300)]
V4L/DVB (6840): tuner: convert tda9887 to use TUNER_SET_CONFIG
Use TUNER_SET_CONFIG to set configuration in tda9887's private state
structure, rather than storing tda9887-specific configuration within
struct tuner.
Update handling of TUNER_SET_CONFIG by tuner-core, to call
&t->fe.ops.analog_demod_ops rather than &t->fe.ops.tuner_ops
analog_demod_ops.set_config passes the request to tuner_ops.set_config,
so this does not break other drivers.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Michael Krufky [Sun, 16 Dec 2007 22:27:23 +0000 (19:27 -0300)]
V4L/DVB (6839): tuner: add set_config to struct analog_tuner_ops
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Michael Krufky [Sun, 16 Dec 2007 22:14:31 +0000 (19:14 -0300)]
V4L/DVB (6838): tda9887: remove references to struct tuner from printk macros
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Michael Krufky [Mon, 17 Dec 2007 13:54:06 +0000 (10:54 -0300)]
V4L/DVB (6837): Convert cx88_input.audioroute to a bitfield
Prevent us from wasting some extra bytes of memory
Thanks to Trent Piepho, for pointing this out.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Mauro Carvalho Chehab [Mon, 17 Dec 2007 13:35:59 +0000 (10:35 -0300)] 
V4L/DVB (6836): Fix CodingStyle troubles caused by the previous cx88 commits
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Frej Drejhammar [Mon, 5 Nov 2007 20:57:11 +0000 (17:57 -0300)] 
V4L/DVB (6834): cx88-video: Enable selection of the WM8775 for cx88 cards
The auto selection of pertinent helper chips (VIDEO_HELPER_CHIPS_AUTO)
should select the wm8775 driver, which is used by at least one
Conexant 2388x based card (Hauppauge HVR-1300), if VIDEO_CX88 is
selected.
Signed-off-by: Frej Drejhammar <frej.drejhammar@gmail.com>
Signed-off-by: Ricardo Cerqueira <v4l@cerqueira.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Ricardo Cerqueira [Tue, 16 Oct 2007 23:52:08 +0000 (20:52 -0300)] 
V4L/DVB (6833): Don't limit cx88 audio routing to blackbird boards
All cx2388 boards need the line-in audio to be routed from an external ADC
(refered to as "ADC mode" in the spec sheet), since the chip is uncapable
of dealing with baseband audio directly.
So... this patch enables normal mode when using the tuner (TV or Radio), and
enables ADC mode with any other source. It'll probably only work with boards
that have supported ADCs (such as the Wolfson wm9775)
Signed-off-by: Ricardo Cerqueira <v4l@cerqueira.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Michael Krufky [Sat, 13 Oct 2007 23:42:45 +0000 (20:42 -0300)]
V4L/DVB (6832): cx88-blackbird: don't mute audio when stopping the codec
We should not mute the audio input when we stop the codec,
because it will interfere with the live uncompressed stream.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Reviewed-by: Jelle Foks <jelle@foks.8m.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Ricardo Cerqueira [Sun, 30 Sep 2007 16:02:49 +0000 (13:02 -0300)]
V4L/DVB (6831): Audio routes fix for blackbird boards with the wm8775 ADC
Fix lack of audio on the MPEG-2 stream of wm8775 based blackbirds.
The wm8775 module initializes the audio input at "route 2", which doesn't
hold true for all boards. The HVR-1300, for example, uses route 1 for
tuner audio, and route 2 for baseband. So we must route the audio to the
proper input depending on what video input is being used.
Signed-off-by: Ricardo Cerqueira <v4l@cerqueira.org>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Jelle Foks [Mon, 21 May 2007 17:48:58 +0000 (14:48 -0300)] 
V4L/DVB (6830): cx88-blackbird: remove unnecessary encoder unmute
Remove the unnecessary BLACKBIRD_UNMUTE calls to the mpeg encoder in
cx88-blackbird.c
The encoder is never muted, hence unmuting should then only be necessary
once after hardware initialization.
I tested this from warm boots and cold boots (with long power down time
to ensure the sram in the chip is emptied), and found that after the
firmware upload the encoder is apparently not muted, making the unmutes
unnecessary.
Signed-off-by: Jelle Foks <jelle@foks.8m.com>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Jelle Foks [Mon, 21 May 2007 17:46:06 +0000 (14:46 -0300)]
V4L/DVB (6829): cx88-blackbird: remove unnecessary msleep()'s
Remove the unnecessary msleep()'s in cx88-blackbird.c
Signed-off-by: Jelle Foks <jelle@foks.8m.com>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Jelle Foks [Mon, 21 May 2007 17:36:01 +0000 (14:36 -0300)]
V4L/DVB (6828): cx88-blackbird: audio improvements
This patch should fix the 'muted audio' and 'raspy audio' problem for
mpeg2 streams out of cx88-blackbird devices.
Especially mythtv users would find that the audio would often sound bad
(aliased, or 'raspy'), mainly related to channel changes, many (all?)
other users would find that there was no audio at all in the mpeg data
from the encoder chip, unless the audio was manually unmuted.
The patch includes the following modifications:
Don't actually start the mpeg2 encoder until the device is read from
by the application.
Wait until the audio is stable for at least 400ms before starting the
mpeg encoder.
Mute/Unmute the audio when starting/stopping the mpeg encoder.
Stop the mpeg encoder when changing parameters and when changing tuner
frequency.
Add a variable 'mpeg_active' to struct cx8802_dev to allow tracking of
whether or not the mpeg2 encoder is active.
Load the firmware on cx88-blackbird driver load.
Signed-off-by: Jelle Foks <jelle@foks.8m.com>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Mauro Carvalho Chehab [Sun, 16 Dec 2007 12:24:30 +0000 (09:24 -0300)]
V4L/DVB (6827): Auto-selects D2633 for ATSC
ATSC standard-specific firmware is D2633 on both v2.5 and v2.7. Better to
auto-select this firmware, overriding ctrl.d2633.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Michael Krufky [Thu, 13 Dec 2007 13:11:49 +0000 (10:11 -0300)]
V4L/DVB (6822): s5h1409: use VSB IF frequency ( 44 / 5.38 MHz ) unless otherwise specified
use VSB IF frequency ( 44 / 5.38 MHz ) if qam_if is invalid or unspecified
Acked-by: Steven Toth <stoth@hauppauge.com>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Michael Krufky [Thu, 13 Dec 2007 13:04:10 +0000 (10:04 -0300)]
V4L/DVB (6821): s5h1409: fix IF frequency configuration
On the s5h1409 demod, the IF frequency for VSB is limited to 44 / 5.38 MHz.
Hardcode VSB IF frequency within the driver to 44 / 5.38 MHz.
QAM IF frequency remains configurable via attach-time configuration.
Acked-by: Steven Toth <stoth@hauppauge.com>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Andrew Morton [Thu, 13 Dec 2007 00:43:57 +0000 (21:43 -0300)] 
V4L/DVB (6818): git-dvb: drivers/media/dvb/frontends/zl10353.c: avoid 64-bit divide
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Acked-by: Chris Pascoe <c.pascoe@itee.uq.edu.au>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Mauro Carvalho Chehab [Thu, 13 Dec 2007 19:15:41 +0000 (16:15 -0300)]
V4L/DVB (6817): Cleanup kernel thread and provide overrun detection
The previous code were a little bit messy. Cleans it up.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Mauro Carvalho Chehab [Thu, 13 Dec 2007 19:13:37 +0000 (16:13 -0300)]
V4L/DVB (6816): Add proper locking for buffer filling
Avoids de-alocating buffers before finishing to fill a buffer
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Mauro Carvalho Chehab [Thu, 13 Dec 2007 16:30:14 +0000 (13:30 -0300)]
V4L/DVB (6815): Fix vivi internal debug messages
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Daniel Walker [Wed, 12 Dec 2007 21:37:54 +0000 (18:37 -0300)] 
V4L/DVB (6812): media: video: usbvision: remove ctrlUrbLock
The ctrlUrbLock has all it's users commented out, and so it's unused. This
patch removes it.
Signed-off-by: Daniel Walker <dwalker@mvista.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Thierry MERLE <thierry.merle@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Andrew Morton [Wed, 12 Dec 2007 21:25:23 +0000 (18:25 -0300)]
V4L/DVB (6811): media-video-usbvision-add-mutex_unlock-to-error-paths-fix
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Thierry MERLE <thierry.merle@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Daniel Walker [Wed, 12 Dec 2007 21:22:48 +0000 (18:22 -0300)]
V4L/DVB (6810): media: video: usbvision: add mutex_unlock() to error paths
There are a few error paths which don't unlock the usbvision->lock.
So I've added mutex_unlock() calls to fix those paths.
Signed-off-by: Daniel Walker <dwalker@mvista.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Thierry MERLE <thierry.merle@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Andrew Morton [Wed, 12 Dec 2007 22:55:49 +0000 (19:55 -0300)]
V4L/DVB (6809): git-dvb: drivers/media/video/et61x251/et61x251_core.c: fix warnings
drivers/media/video/et61x251/et61x251_core.c:390: warning: 'et61x251_i2c_read' defined but not used
drivers/media/video/et61x251/et61x251_core.c:397: warning: 'et61x251_i2c_write' defined but not used
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Andrew Morton [Wed, 12 Dec 2007 22:27:57 +0000 (19:27 -0300)]
V4L/DVB (6808): git-dvb: fix build in drivers/media/dvb/frontends/tda18271.h
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Mauro Carvalho Chehab [Thu, 13 Dec 2007 09:36:22 +0000 (06:36 -0300)]
V4L/DVB (6807): fix debug enable
The changes at vivi_template make debug option to not work properly.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Mauro Carvalho Chehab [Thu, 13 Dec 2007 09:35:26 +0000 (06:35 -0300)]
V4L/DVB (6806): Allow emulating changes of video std by vivi
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Mauro Carvalho Chehab [Thu, 13 Dec 2007 09:34:12 +0000 (06:34 -0300)]
V4L/DVB (6805): video std is a bitmask. Better to print in hexa
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Mauro Carvalho Chehab [Thu, 13 Dec 2007 00:46:26 +0000 (21:46 -0300)]
V4L/DVB (6804): __videobuf_read_start is static
Thanks to Jean Delvare <khali@linux-fr.org> for pointing this.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Michael Krufky [Mon, 10 Dec 2007 01:23:30 +0000 (22:23 -0300)]
V4L/DVB (6801): tda18271: pass i2c gate configuration into tda18271_attach()
If we pass TDA18271_GATE_DIGITAL into tda18271_attach(), it will always try to
use the digital demodulator's i2c gate.
If we pass TDA18271_GATE_ANALOG into tda18271_attach(), it will always try to
use the analog demodulator's i2c gate.
If we pass TDA18271_GATE_AUTO into tda18271_attach(), it will try to use the
analog demodulator's i2c gate when tuning in analog mode, and it will try to
use the digital demodulator's i2c gate when tuning in digital mode.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Michael Krufky [Mon, 10 Dec 2007 01:13:01 +0000 (22:13 -0300)]
V4L/DVB (6800): tda18271: use an enum rather than an integer to store analog / digital state
Use an enum rather than an integer #define to store analog / digital state.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Mauro Carvalho Chehab [Tue, 11 Dec 2007 18:01:57 +0000 (15:01 -0300)]
V4L/DVB (6795): Add EXPORT_SYMBOL_GPL to the saa7134 video control routines
Those newer functions are used by saa7134-empress. Adds export for them:
+EXPORT_SYMBOL_GPL(saa7134_g_ctrl);
+EXPORT_SYMBOL_GPL(saa7134_s_ctrl);
+EXPORT_SYMBOL_GPL(saa7134_queryctrl);
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Mauro Carvalho Chehab [Tue, 11 Dec 2007 15:56:23 +0000 (12:56 -0300)]
V4L/DVB (6793): Convert saa7134-empress to video_ioctl2
saa7134 were converted to video_ioctl2, but saa7134_empress weren't. This broke
saa7134-empress, since it were dependent of saa7134_common_ioctl.
With the conversion, the module had a size decrease of 436 bytes on x86_64:
text data bss dec hex filename
5196 4912 4 10112 2780 old/saa7134-empress.ko
4760 4912 4 9676 25cc new/saa7134-empress.ko
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Mauro Carvalho Chehab [Tue, 11 Dec 2007 15:05:06 +0000 (12:05 -0300)]
V4L/DVB (6792): Fix VBI support
VBI were broken, since there weren't any function handlers for it. This patch
fixes it, by removing the vbi_template, using, instead video_template.
This also saves some space at the data segment.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Mauro Carvalho Chehab [Tue, 11 Dec 2007 14:51:53 +0000 (11:51 -0300)]
V4L/DVB (6791): Rename all vidioc_ to saa7134_
Some functions are used also by saa7134-empress, and need to be exported. To
avoid namespace confusion, rename all of them to saa7134_
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Michael Krufky [Mon, 10 Dec 2007 19:08:25 +0000 (16:08 -0300)]
V4L/DVB (6789): tuner: use char *name instead of 128 byte fixed array for demod info
Don't waste 128 bytes of memory for a name that might not actually need it.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Michael Krufky [Mon, 10 Dec 2007 14:12:59 +0000 (11:12 -0300)]
V4L/DVB (6788): tda8290: fix codingstyle, open brace following struct on the same line
Fix codingstyle issue discovered after using new checkpatch.pl
ERROR: open brace '{' following struct go on the same line
396: FILE: linux/drivers/media/video/tda8290.h:24:
+struct tda829x_config
+{
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Michael Krufky [Sun, 9 Dec 2007 20:21:54 +0000 (17:21 -0300)]
V4L/DVB (6787): tuner: bug-fix: default mode was set to bogus value
Fix type inconsistency in t->mode value, causing the following:
tuner' 1-0043: freq set: unknown mode: 0x0004!
(only visible with tuner debug enabled)
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Michael Krufky [Sun, 9 Dec 2007 16:52:51 +0000 (13:52 -0300)]
V4L/DVB (6786): tuner: add struct analog_demod_info to struct analog_tuner_ops
Store the analog demodulator name in fe.ops.analog_demod_ops.info.name
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Michael Krufky [Sun, 9 Dec 2007 05:26:48 +0000 (02:26 -0300)]
V4L/DVB (6785): tda8290: remove dependency on struct tuner
- remove dependency of tda8290 module on struct tuner
- move tuner_foo printk macros from tuner-driver.h into tuner-core.c
- clean up #includes of tuner-i2c.h / tuner-driver.h
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Michael Krufky [Sun, 9 Dec 2007 08:16:10 +0000 (05:16 -0300)]
V4L/DVB (6784): tda8290: prevent possible memory leak
Always call tda829x_release if tda829x_attach fails for a reason
other than failure to allocate memory for private structure.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Michael Krufky [Sat, 8 Dec 2007 20:06:30 +0000 (17:06 -0300)]
V4L/DVB (6783): tuner: combine set_tv_freq and set_radio_freq into a single set_params method
We can tell whether we are tuning television or radio by testing for
struct analog_parameters *params->mode == V4L2_TUNER_RADIO
There is no longer any need for separate set_tv_freq and
set_radio_freq functions in the analog tuner demodulator modules.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Michael Krufky [Sat, 8 Dec 2007 19:25:41 +0000 (16:25 -0300)]
V4L/DVB (6782): tda8290: access frontend structure directly, where possible
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Richard Knutsson [Sat, 8 Dec 2007 13:35:06 +0000 (10:35 -0300)] 
V4L/DVB (6776): ivtv: Some general fixes
Fix "warning: Using plain integer as NULL pointer".
Convert 'x < y ? x : y' to use min() instead.
Signed-off-by: Richard Knutsson <ricknu-0@student.ltu.se>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Mike Isely [Sat, 8 Dec 2007 20:20:06 +0000 (17:20 -0300)] 
V4L/DVB (6773): pvrusb2: rework device descriptor layout
The pvrusb2 driver tries to keep all device specific attributes in a
single data structure in one source file. This change further cleans
up how that table is set up. We now try to group everything together
for each specific device, and the number of symbols exported from this
module has now been reduced to a single global.
Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Mike Isely [Sat, 8 Dec 2007 20:17:44 +0000 (17:17 -0300)]
V4L/DVB (6772): pvrusb2: Remove obsolete (and misleading) comment
Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Mike Isely [Sat, 8 Dec 2007 20:17:09 +0000 (17:17 -0300)]
V4L/DVB (6771): pvrusb2: Remove old obsolete CONFIG flags for pvrusb2 driver
Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Mike Isely [Sat, 8 Dec 2007 20:15:55 +0000 (17:15 -0300)]
V4L/DVB (6770): pvrusb2: Device CONFIG flags for OnAir device support
Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Mike Isely [Sat, 8 Dec 2007 20:11:13 +0000 (17:11 -0300)]
V4L/DVB (6769): pvrusb2: Implement experimental support for OnAir Creator and USB2 devices
Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Mike Isely [Sat, 8 Dec 2007 20:08:32 +0000 (17:08 -0300)]
V4L/DVB (6768): pvrusb2: Mark Gotview hardware as having a cx2584x part
Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Hans Verkuil [Sat, 8 Dec 2007 10:43:14 +0000 (07:43 -0300)] 
V4L/DVB (6766): ivtv: remove i2c legacy support from drivers that no longer need it
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Hans Verkuil [Sat, 8 Dec 2007 00:01:15 +0000 (21:01 -0300)]
V4L/DVB (6765): ivtv: convert to bus-based i2c API
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Hans Verkuil [Fri, 7 Dec 2007 23:48:29 +0000 (20:48 -0300)]
V4L/DVB (6764): ivtv: select VIDEO_IR in Kconfig
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Hans Verkuil [Fri, 7 Dec 2007 23:40:16 +0000 (20:40 -0300)]
V4L/DVB (6763): ivtv: add AVerMedia EZMaker PCI Deluxe support
Add support for the AVerMedia EZMaker PCI Deluxe and update the ivtv cardlist.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Hans Verkuil [Fri, 7 Dec 2007 23:31:17 +0000 (20:31 -0300)]
V4L/DVB (6762): ivtv: update version number to 1.2
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Mauro Carvalho Chehab [Mon, 10 Dec 2007 13:53:20 +0000 (10:53 -0300)]
V4L/DVB (6759): CodingStyle fixes
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Mauro Carvalho Chehab [Mon, 10 Dec 2007 12:33:52 +0000 (09:33 -0300)]
V4L/DVB (6758): Miscelaneous cleanups
Manually fixed all pertinent checkpatch.pl errors inside the source code.
Also removed some unused code at the driver and a few minor cleanups.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Mauro Carvalho Chehab [Mon, 10 Dec 2007 07:43:38 +0000 (04:43 -0300)]
V4L/DVB (6755): Avoid troubles when using multiple devices
mv_count is a counter used to move the vertical bars. Before this patch, it
where a static var. This works fine for just one device. However, when using
multiple devices, every device would increment it.
This patch moves it to its correct place: struct vivi_dev. So, now, each device
has its own data.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Mauro Carvalho Chehab [Mon, 10 Dec 2007 07:38:11 +0000 (04:38 -0300)]
V4L/DVB (6754): Allow vivi to open multiple video devices
Now, it is possible to open multiple vivi devices, by using n_devs parameter.
This makes vivi driver closer to a real one.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Mauro Carvalho Chehab [Mon, 10 Dec 2007 07:07:03 +0000 (04:07 -0300)]
V4L/DVB (6753): Fix vivi to support non-zero minor node
There were a trouble at vivi driver when using non-zero inodes. This where due
to not properly preserving the minor inode after calling video_register. Since
this driver is a reference for newer drivers, and it is possible to have more
than one video device inside the machine, this patch makes vivi to dynamically
allocate video_device struct.
Thanks to Gregor Jasny <jasny@vidsoft.de> for pointing the issue.
Also, this patch removes a very anoying (but useless) message of not having a
proper release call.
CC: Gregor Jasny <jasny@vidsoft.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Albert Graham [Sun, 9 Dec 2007 12:44:38 +0000 (09:44 -0300)] 
V4L/DVB (6752): saa7134: Enable remote control support for Avermedia M102
This patch enabled the IR remote control for the Avermedia M102 (card=110),
which appears to be the same IR as the already supported device on the
Avermedia AVerTV GO 007 FM (card=57) model, the code is two one liners which
enable the IR for this device (subsystem: 1461:f31e)
Signed-off-by: Albert Graham <agraham@g-b.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Andrew Morton [Sat, 8 Dec 2007 00:14:43 +0000 (21:14 -0300)]
V4L/DVB (6749): v4l-nopage-fix
dont just copy-and-paste stuff.
(compile-tested this time)
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Cc: Nick Piggin <nickpiggin@yahoo.com.au>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Nick Piggin [Fri, 7 Dec 2007 20:57:38 +0000 (17:57 -0300)] 
V4L/DVB (6748): Subject: v4l: nopage
Convert v4l from nopage to fault.
Remove redundant vma range checks.
Signed-off-by: Nick Piggin <npiggin@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Michael Krufky [Fri, 7 Dec 2007 03:33:08 +0000 (00:33 -0300)]
V4L/DVB (6745): tda18271: remove tuning offset for atsc/qam
The tuning request coming in from userspace is already center adjusted,
so we should not adjust to center (+1.75mhz) within the driver.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Hans Verkuil [Sun, 2 Dec 2007 10:03:45 +0000 (07:03 -0300)]
V4L/DVB (6743): cx25840: fix endianness inconsistency
cx25840_read4 reads a little-endian 32-bit value whereas cx25840_write4 writes
the 32-bit value as big-endian. Convert write4 to use little-endian as well
(that's the correct endianness).
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Hans Verkuil [Sun, 2 Dec 2007 09:56:00 +0000 (06:56 -0300)]
V4L/DVB (6742): ivtv: fix incorrect debug message
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Hans Verkuil [Thu, 1 Nov 2007 16:38:12 +0000 (13:38 -0300)]
V4L/DVB (6741): cx2341x: codingstyle cleanups
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Hans Verkuil [Thu, 1 Nov 2007 10:58:17 +0000 (07:58 -0300)]
V4L/DVB (6740): tlv320aic23b: codingstyle cleanups
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Hans Verkuil [Thu, 1 Nov 2007 10:54:57 +0000 (07:54 -0300)]
V4L/DVB (6739): cs53l32a: codingstyle cleanups
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Hans Verkuil [Thu, 1 Nov 2007 10:45:54 +0000 (07:45 -0300)]
V4L/DVB (6738): wm8739: codingstyle cleanups
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Hans Verkuil [Thu, 1 Nov 2007 10:35:41 +0000 (07:35 -0300)]
V4L/DVB (6737): wm8775: codingstyle cleanup
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Mauro Carvalho Chehab [Fri, 7 Dec 2007 20:34:48 +0000 (17:34 -0300)]
V4L/DVB (6736): Fix some errors at the video_ioctl2 conversion
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Mauro Carvalho Chehab [Fri, 7 Dec 2007 20:23:38 +0000 (17:23 -0300)]
V4L/DVB (6735): Reorder functions to make easier to compare with the previous code
After this patch, the order of the functions will be the same as before the
patch converting the driver to user video_ioctl2. This makes easier to diff
between the previous version and the newer one.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Douglas Schilling Landgraf [Fri, 7 Dec 2007 20:09:53 +0000 (17:09 -0300)] 
V4L/DVB (6734): Converted saa7134-video to use video_ioctl2
Signed-off-by: Douglas Schilling Landgraf <dougsland@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Oliver Neukum [Mon, 3 Dec 2007 09:48:43 +0000 (06:48 -0300)] 
V4L/DVB (6732): dsbr100 violates DMA coherency rules
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Richard Knutsson [Sun, 2 Dec 2007 17:47:01 +0000 (14:47 -0300)]
V4L/DVB (6731): ivtv: Remove a invalid shadow-variable
Remove the shadowing 'struct v4l2_chip_ident *chip', since it already exists
and makes the if-statement useless.
Signed-off-by: Richard Knutsson <ricknu-0@student.ltu.se>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Michael Krufky [Sun, 2 Dec 2007 20:37:38 +0000 (17:37 -0300)]
V4L/DVB (6728): tda18271: fix register dump format
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Michael Krufky [Sun, 2 Dec 2007 19:36:05 +0000 (16:36 -0300)]
V4L/DVB (6727): tda18271: convert table lookup loops to functions
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Michael Krufky [Sun, 2 Dec 2007 14:03:57 +0000 (11:03 -0300)]
V4L/DVB (6726): tda18271: set image rejection validity
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Michael Krufky [Sun, 2 Dec 2007 05:45:04 +0000 (02:45 -0300)]
V4L/DVB (6725): tda18271: improve debug flexibility
converted debug module option to an or-able setting.
1 = info
2 = table map values
4 = register dumps
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Michael Krufky [Sun, 2 Dec 2007 05:32:49 +0000 (02:32 -0300)]
V4L/DVB (6724): tda18271: remove duplicated code
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Michael Krufky [Sat, 1 Dec 2007 20:40:16 +0000 (17:40 -0300)]
V4L/DVB (6723): tda18271: only force init once during attach
Once the image rejection calibration procedure has been successful,
we should not initialize the tuner registers again.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Ian Armstrong [Tue, 13 Nov 2007 22:15:25 +0000 (19:15 -0300)] 
V4L/DVB (6719): ivtv: ivtv-yuv clean-up + source cropping bug-fix
ivtv-yuv code clean up & reformat. Includes minor changes to some debug lines.
Also fixes a bug found during the reformatting, which would cause the
incorrect amount of yuv data to be sent to the card if source cropping
coordinates were used.
Apart from the bug-fix, there should be no functional difference to the
previous version.
Signed-off-by: Ian Armstrong <ian@iarmst.demon.co.uk>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Ian Armstrong [Mon, 5 Nov 2007 17:30:03 +0000 (14:30 -0300)]
V4L/DVB (6718): ivtv: ivtv yuv format description correction
The driver was incorrectly reporting that it supported YUV 4:2:2 output, when
it is actually YUV 4:2:0. Though I believe the hardware can be pushed to
4:2:2, we don't currently support that.
Signed-off-by: Ian Armstrong <ian@iarmst.demon.co.uk>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Ian Armstrong [Mon, 5 Nov 2007 17:27:09 +0000 (14:27 -0300)]
V4L/DVB (6717): ivtv: Initial merge of video48 yuv handling into the IVTV_IOC_DMA_FRAME framework
Previously, all yuv data written to /dev/video48 had only basic support with
no double buffering to avoid display tearing.
With this patch, yuv frames written to video48 are now handled by the existing
IVTV_IOC_DMA_FRAME framework. As such, the frames are hardware buffered to
avoid tearing, and honour scaling mode & field order options. Unlike the
proprietary IVTV_IOC_DMA_FRAME ioctl, all parameters are controlled by the
V4L2 API.
Due to mpeg & yuv output restrictions being different, their V4L2 output
controls have been separated. To control the yuv output, the V4L2 calls must
be done via video48.
If the ivtvfb module is loaded, there will be one side effect to this merge.
The yuv output window will be constrained to the visible framebuffer area. In
the event that a virtual framebuffer size is being used, the limit to the
output size will be the virtual dimensions, but only the portion that falls
within the currently visible area of the framebuffer will be shown.
Like the IVTV_IOC_DMA_FRAME ioctl, the supplied frames must be padded to 720
pixels wide. However the height must only be padded up the nearest multiple
of 32. This would mean an image of 102 lines must be padded to 128. As long
as the true source image size is given, the padding will not be visible in
the final output.
Signed-off-by: Ian Armstrong <ian@iarmst.demon.co.uk>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Ian Armstrong [Mon, 22 Oct 2007 17:24:26 +0000 (14:24 -0300)]
V4L/DVB (6716): ivtv: yuv interlace mode change
Interlace mode selection code moved into the frame setup phase, so it's now
run before the frame is loaded into a hardware buffer. Given that it can
affect how a new frame is displayed, it was a bit stupid running it after the
frame was already visible.
A few stray interlace related variables which were linked to individual frames
have now been moved into the yuv_frame_info struct. This means that all
variables linked to a specific frame are in the same place & not scattered.
Minor code reformatting in areas touched by the above changes.
Signed-off-by: Ian Armstrong <ian@iarmst.demon.co.uk>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Ian Armstrong [Sun, 21 Oct 2007 11:33:59 +0000 (08:33 -0300)]
V4L/DVB (6715): ivtv: Remove unnecessary register update
To reduce the number of display register accesses, the yuv code keeps track of
the current video settings. Should there be a change in any single parameter,
it will update the associated display registers to ensure everything is
displayed correctly.
The existing check also looks at the field order for the video. This is not
required, since field reversal does not require any display register changes.
This patch removes the field order from the check.
Signed-off-by: Ian Armstrong <ian@iarmst.demon.co.uk>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Ian Armstrong [Sun, 21 Oct 2007 11:09:10 +0000 (08:09 -0300)]
V4L/DVB (6714): ivtv: yuv frame parameter fix
Inadvertently missed a line when converting code to new hardware buffering
method. In some circumstances, this would lead to a frame being displayed
using parameters belonging to another frame.
Signed-off-by: Ian Armstrong <ian@iarmst.demon.co.uk>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
projects / linux-2.6 / log
