herton [Fri, 28 Nov 2008 00:53:24 +0000 (22:53 -0200)]
rtl8187: fix retry count passed in rtl8187_tx
I mistakenly changed retry count passed in rtl8187_tx in previous change
"rtl8187: feedback transmitted packets using tx close descriptor for
8187B". For 8187 it should represent the number of retries (retry count
limit). As explained by Johannes Berg, .count represents the number of
tries (not retries), and retries = tries - 1.
Signed-off-by: Herton Ronaldo Krzesinski <herton@mandriva.com.br>
Tested-by: Hin-Tak Leung <htl10@users.sourceforge.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg [Thu, 27 Nov 2008 22:13:38 +0000 (23:13 +0100)]
wireless: clean up radiotap a bit
No need to pad the header so no constant needed for that,
no need to carry any version number from netbsd nor CVS
IDs from them.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Sujith [Thu, 27 Nov 2008 04:16:27 +0000 (09:46 +0530)]
ath9k: Handle channel initialization for AP mode
Hostapd now passes the HT parameters through the config()
callback, use these to set the appropriate channel in AP mode.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fabio Rossi [Wed, 26 Nov 2008 21:44:23 +0000 (22:44 +0100)]
mac80211: accept empty strings for hidden SSIDs
Some access points (e.g. Sitecom WL-174) use an empty string as hidden SSID.
Signed-off-by: Fabio Rossi <rossi.f@inwind.it>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg [Wed, 26 Nov 2008 22:31:40 +0000 (23:31 +0100)]
cfg80211: handle SIOCGIWMODE/SIOCSIWMODE
further reducing wext code in mac80211.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg [Wed, 26 Nov 2008 21:36:31 +0000 (22:36 +0100)]
cfg80211: handle SIOCGIWNAME
This patch moves the SIOCGIWNAME handling from mac80211 to cfg80211.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Bob Copeland [Wed, 26 Nov 2008 21:17:25 +0000 (16:17 -0500)]
ath5k: enable combined michael mic in key cache
For mac revisions >= "Griffin," the hardware allows the mic tx and rx
authenticator keys to share the same cache line, whereas earlier
hardware can only store the rx. Enable the combined mic on hardware
that supports it.
Changes to ath5k.h
Changes-licensed-under: 3-Clause-BSD
Changes to attach.c, pcu.c, reg.h
Changes-licensed-under: ISC
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Bob Copeland [Wed, 26 Nov 2008 01:55:21 +0000 (20:55 -0500)]
ath5k: clean up ath5k_hw_set_key
Status: O
With the addition of TKIP (and soon CCMP), key->alg is a more useful
guide to key type than the key length.
This patch cleans up key type assignment in ath5k_hw_set_key by
extracting it into its own function. It also replaces the separate
memcpy() calls for extracting key material into the hardware format
with a loop that works regardless of key size.
Finally, the patch removes support for WEP-128 since it is a
non-standard key length that mac80211 also doesn't use.
Changes-licensed-under: ISC
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Bob Copeland [Wed, 26 Nov 2008 21:17:11 +0000 (16:17 -0500)]
ath5k: preserve higher order bits when setting mac address
In some cases we would like to set the mac address without changing
the operating mode. However, Atheros cards store PCU data in the high
16 bits of the mac address register. Change ath5k_hw_set_lladdr() to
not clobber the PCU settings.
Changes-licensed-under: ISC
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Harvey Harrison [Wed, 26 Nov 2008 21:12:52 +0000 (13:12 -0800)]
iwlwifi: remove uses of __constant_{endian} helpers
The base versions handle constant folding just fine.
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Luis R. Rodriguez [Wed, 26 Nov 2008 21:03:08 +0000 (13:03 -0800)]
nl80211: relicense nl80211.h under the ISC
We have a few BSD/ISC licensed userspace applications which
include nl80211.h from the kernel. To avoid legal ambiguity
for usage of the header file in these projects we rather simply
relicense the header file under the ISC. We've received consent
from all contributors to it.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Acked-by: Michael Wu <flamingice@sourmilk.net>
Acked-by: Luis Carlos Cobo <luisca@cozybit.com>
Acked-by: Michael Buesch <mb@bu3sch.de>
Acked-by: Jouni Malinen <jouni.malinen@atheros.com>
Acked-by: Colin McCabe <colin@cozybit.com>
Acked-by: Javier Cardona <javier@cozybit.com>
Cc: johannes@sipsolutions.net
Cc: altape@eden.rutgers.edu
Cc: luisca@cozybit.com
Cc: mb@bu3sch.de
Cc: jouni.malinen@atheros.com
Cc: colin@cozybit.com
Cc: javier@cozybit.com
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Jouni Malinen [Wed, 26 Nov 2008 14:15:24 +0000 (16:15 +0200)]
nl80211: Add frequency configuration (including HT40)
This patch adds new NL80211_CMD_SET_WIPHY attributes
NL80211_ATTR_WIPHY_FREQ and NL80211_ATTR_WIPHY_SEC_CHAN_OFFSET to allow
userspace to set the operating channel (e.g., hostapd for AP mode).
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg [Wed, 26 Nov 2008 14:02:58 +0000 (15:02 +0100)]
mac80211: only transition STAs ps->wake on data frames
When a station goes to PS mode to scan, it will then send
probe requests without the PS bit set. mac80211 will take
that as indication that the station woke up, but it didn't.
This patch changes mac80211 to only consider doze->wake
transitions on data frames to to fix that issue.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Cc: Jouni Malinen <j@w1.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Tomas Winkler [Tue, 25 Nov 2008 21:36:01 +0000 (13:36 -0800)]
iwlwifi: properly initialize calibration command header
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Tomas Winkler [Tue, 25 Nov 2008 11:05:44 +0000 (13:05 +0200)]
mac80211: disassociate prior to unlinking AP/station
This patch reorders calls during disassociation in
ieee80211_set_disassoc function.
Since sta_info_unlink calls sta_notify(REMOVE) it will
remove the station representing AP from the driver before
it has disassociated from it using bss_info_changed callback.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
John W. Linville [Mon, 1 Dec 2008 19:56:41 +0000 (14:56 -0500)]
mac80211: deauth when interface is marked down
It seems like proper etiquette to let other stations know when we are
going down in either STA or IBSS mode. This also notifies userland, so
wpa_supplicant doesn't get confused.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
John W. Linville [Wed, 3 Dec 2008 18:55:38 +0000 (13:55 -0500)]
hostap: select required crypto bits in Kconfig
This is fallout from moving the crypto stuff to the new lib80211
component.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Shaddy Baddah [Fri, 28 Nov 2008 06:10:45 +0000 (17:10 +1100)]
zd1211rw: use unaligned safe memcmp() in-place of compare_ether_addr()
Under my 2.6.28-rc6 sparc64, when associating to an AP through my
zd1211rw device, I was seeing kernel log messages like (not exact output):
Kernel unaligned access at TPC[
10129b68] zd_mac_rx+0x144/0x32c [zd1211rw]
For the zd1211rw module, on RX, the 80211 packet will be located after
the PLCP header in the skb data buffer. The PLCP header being 5 bytes
long, the 80211 header will start unaligned from an aligned skb
buffer.
As per Documentation/unaligned-memory-access.txt, we must replace the
not unaligned() safe compare_ether_addr() with memcmp() to protect
architectures that require alignment.
Signed-off-by: Shaddy Baddah <shaddy_baddah@hotmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Shaddy Baddah [Fri, 28 Nov 2008 06:08:10 +0000 (17:08 +1100)]
mac80211: use unaligned safe memcmp() in-place of compare_ether_addr()
After fixing zd1211rw: use unaligned safe memcmp() in-place of
compare_ether_addr(), I started to see kernel log messages detailing
unaligned access:
Kernel unaligned access at TPC[
100f7f44] sta_info_get+0x24/0x68 [mac80211]
As with the aforementioned patch, the unaligned access was eminating
from a compare_ether_addr() call. Concerned that whilst it was safe to
assume that unalignment was the norm for the zd1211rw, and take
preventative measures, it may not be the case or acceptable to use the
easy fix of changing the call to memcmp().
My research however indicated that it was OK to do this, as there are
a few instances where memcmp() is the preferred mechanism for doing
mac address comparisons throughout the module.
Signed-off-by: Shaddy Baddah <shaddy_baddah@hotmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Zhu Yi [Thu, 27 Nov 2008 05:42:20 +0000 (13:42 +0800)]
ipw2200: fix netif_*_queue() removal regression
In "ipw2200: Call netif_*_queue() interfaces properly", netif_stop_queue()
and netif_wake_queue() were removed with the reason
"netif_carrier_{on,off}() handles starting and stopping packet flow into
the driver". The patch also removes a valid condition check that
ipw_tx_skb() cannot be called if device is not in STATUS_ASSOCIATED state.
But netif_carrier_off() doesn't guarantee netdev->hard_start_xmit won't
be called because linkwatch event is handled in a delayed workqueue. This
caused a kernel oops reported by Frank Seidel:
https://bugzilla.novell.com/show_bug.cgi?id=397390
This patch fixes the problem by moving the STATUS_ASSOCIATED check back
to ipw_tx_skb(). It also adds a missing netif_carrier_off() call to
ipw_disassociate().
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: Chatre, Reinette <reinette.chatre@intel.com>
Tested-by: Frank Seidel <fseidel@suse.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Tomas Winkler [Tue, 25 Nov 2008 21:29:03 +0000 (23:29 +0200)]
iwlwifi: clean key table in iwl_clear_stations_table function
This patch cleans uCode key table bit map iwl_clear_stations_table
since all stations are cleared also the key table must be.
Since the keys are not removed properly on suspend by mac80211
this may result in exhausting key table on resume leading
to memory corruption during removal
This patch also fixes a memory corruption problem reported in
http://marc.info/?l=linux-wireless&m=
122641417231586&w=2 and tracked in
http://bugzilla.kernel.org/show_bug.cgi?id=12040.
When the key is removed a second time the offset is set to 255 - this
index is not valid for the ucode_key_table and corrupts the eeprom pointer
(which is 255 bits from ucode_key_table).
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Reported-by: Carlos R. Mafra <crmafra2@gmail.com>
Reported-by: Lukas Hejtmanek <xhejtman@ics.muni.cz>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Doug Leith [Fri, 5 Dec 2008 01:17:18 +0000 (17:17 -0800)]
tcp: tcp_vegas ssthresh bug fix
This patch fixes a bug in tcp_vegas.c. At the moment this code leaves
ssthresh untouched. However, this means that the vegas congestion
control algorithm is effectively unable to reduce cwnd below the
ssthresh value (if the vegas update lowers the cwnd below ssthresh,
then slow start is activated to raise it back up). One example where
this matters is when during slow start cwnd overshoots the link
capacity and a flow then exits slow start with ssthresh set to a value
above where congestion avoidance would like to adjust it.
Signed-off-by: Doug Leith <doug.leith@nuim.ie>
Signed-off-by: David S. Miller <davem@davemloft.net>
Martin Willi [Thu, 4 Dec 2008 23:40:17 +0000 (15:40 -0800)]
xfrm: Accept ESP packets regardless of UDP encapsulation mode
From: Martin Willi <martin@strongswan.org>
An IPsec node speaking IKEv2 MUST accept incoming UDP encapsulated
ESP packets, even if no NAT situation is detected. This is important
if MOBIKE is in use. Some implementation keep the encapsulation
mode if they move out of a NAT situation.
Signed-off-by: David S. Miller <davem@davemloft.net>
Wang Chen [Thu, 4 Dec 2008 23:12:20 +0000 (15:12 -0800)]
sgi-xp: Kill directly reference of netdev->priv
Simply replace netdev->priv with netdev_priv().
[ Kill unnecessary casts, noticed by Ilpo -DaveM ]
Signed-off-by: Wang Chen <wangchen@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Wang Chen [Thu, 4 Dec 2008 23:07:33 +0000 (15:07 -0800)]
um: Kill directly reference of netdev->priv
Simply replace netdev->priv with netdev_priv().
Signed-off-by: Wang Chen <wangchen@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Wang Chen [Thu, 4 Dec 2008 23:06:56 +0000 (15:06 -0800)]
xtensa: Kill directly reference of netdev->priv
Simply replace netdev->priv with netdev_priv().
Signed-off-by: Wang Chen <wangchen@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Wang Chen [Thu, 4 Dec 2008 23:06:27 +0000 (15:06 -0800)]
simeth: Kill directly reference of netdev->priv
Simply replace netdev->priv with netdev_priv().
Signed-off-by: Wang Chen <wangchen@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Oliver Hartkopp [Thu, 4 Dec 2008 23:01:08 +0000 (15:01 -0800)]
can: omit received RTR frames for single ID filter lists
Since commit
d253eee20195b25e298bf162a6e72f14bf4803e5 the single CAN
identifier filter lists handle only non-RTR CAN frames.
So we need to omit the check of these filter lists when receiving RTR
CAN frames.
Signed-off-by: Oliver Hartkopp <oliver@hartkopp.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Chas Williams [Thu, 4 Dec 2008 22:58:13 +0000 (14:58 -0800)]
ATM: CVE-2008-5079: duplicate listen() on socket corrupts the vcc table
As reported by Hugo Dias that it is possible to cause a local denial
of service attack by calling the svc_listen function twice on the same
socket and reading /proc/net/atm/*vc
Signed-off-by: Chas Williams <chas@cmf.nrl.navy.mil>
Signed-off-by: David S. Miller <davem@davemloft.net>
Joe Perches [Thu, 4 Dec 2008 06:27:25 +0000 (22:27 -0800)]
net/ipv6/ip6mr.c: Use kmem_cache_zalloc, remove memset
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Wang Chen [Thu, 4 Dec 2008 06:24:05 +0000 (22:24 -0800)]
if_usb: Kill directly reference of netdev->priv
Simply replace netdev->priv with netdev_priv().
Signed-off-by: Wang Chen <wangchen@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Luotao Fu [Thu, 4 Dec 2008 06:23:18 +0000 (22:23 -0800)]
smc91x: remove isa stuff from smc91x driver
ISA support in smc91x is incomplete. I doubt there're any smc91x isa card.
This driver is greatly used on arm pxa platforms. Hence we remove the
isa stuff from smc91x driver.
Signed-off-by: Luotao Fu <lfu@pengutronix.de>
Acked-by: Steve Glendinning <steve.glendinning@smsc.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Benjamin Thery [Thu, 4 Dec 2008 06:22:16 +0000 (22:22 -0800)]
net: /proc/net/ip_mr_cache, display Iif as a signed short
Today, iproute2 fails to show multicast forwarding unresolved cache
entries while scanning /proc/net/ip_mr_cache.
Indeed, it expects to see -1 in 'Iif' column to identify unresolved
entries but the kernel outputs 65535. It's a signed/unsigned issue:
'Iif', the source interface, is retrieved from member mfc_parent in
struct mfc_cache. mfc_parent is a vifi_t: unsigned short, but is
displayed in ipmr_mfc_seq_show() as "%-3d", signed integer.
In unresolevd entries, the 65535 value (0xFFFF) comes from this define:
#define ALL_VIFS ((vifi_t)(-1))
That may explains why the guy who added support for this in iproute2
thought a -1 should be expected.
I don't know if this must be fixed in kernel or in iproute2. Who is
right? What is the correct API? How was it designed originally?
I let you decide if it should goes in the kernel or be fixed in iproute2.
Signed-off-by: Benjamin Thery <benjamin.thery@bull.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Benjamin Thery [Thu, 4 Dec 2008 06:21:47 +0000 (22:21 -0800)]
net: fix /proc/net/ip_mr_cache display - V2
/proc/net/ip_mr_cache and /proc/net/ip6_mr_cache displays garbage when
showing unresolved mfc_cache entries.
[root@qemu tests]# cat /proc/net/ip_mr_cache
Group Origin Iif Pkts Bytes Wrong Oifs
014C00EF 010014AC 1 10 10050 0 2:1 3:1
024C00EF 010014AC 65535 514 2 -
559067475
The first line is correct. It is a resolved cache entry, 10 packets used it...
The second line represents an unresolved entry, and the columns Pkts(4th),
Bytes(5th) and Wrong(6th) just show garbage.
In struct mfc_cache, there's an union to store data for resolved and
unresolved cases. And what ipmr_mfc_seq_show() is printing in these
columns for the unresolved entries is some bytes from mfc_cache.mfc_un.res.
Bad.
(eg. In our case -
559067475 is in fact 0xdead4ead which is the spinlock
magic from mfc_cache.mfc_un.unres.unresolved.lock.magic).
This patch replaces the garbage data written in these columns for the
unresolved entries by '0' (zeros) which is more correct.
This change doesn't break the ABI.
Also, mfc->mfc_un.res.pkt, mfc->mfc_un.res.bytes, mfc->mfc_un.res.wrong_if
are unsigned long.
It applies on top of net-next-2.6.
The patch for net-2.6 is slightly different because of the NIP6_FMT to
%pI6 conversion that was made in the seq_printf.
Changelog:
==========
V2:
* Instead of breaking the ABI by suppressing the columns that have no
meaning for unresolved entries, fill them with 0 values.
Signed-off-by: Benjamin Thery <benjamin.thery@bull.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Alexey Dobriyan [Thu, 4 Dec 2008 06:19:52 +0000 (22:19 -0800)]
netdev: remove pathetic compile-command lines
-m486, -O6 are partircularly amusing.
Remove some other useless lines near as well.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Uwe Kleine-König [Thu, 4 Dec 2008 06:18:59 +0000 (22:18 -0800)]
netx-eth: initialize per device spinlock
The spinlock used in the netx-eth driver was never properly initialized.
This was noticed using CONFIG_DEBUG_SPINLOCK=y
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
David Woodhouse [Thu, 4 Dec 2008 06:12:38 +0000 (22:12 -0800)]
atm: 32-bit ioctl compatibility
We lack compat ioctl support through most of the ATM code. This patch
deals with most of it, and I can now at least use BR2684 and PPPoATM
with 32-bit userspace.
I haven't added a .compat_ioctl method to struct atm_ioctl, because
AFAICT none of the current users need any conversion -- so we can just
call the ->ioctl() method in every case. I looked at br2684, clip, lec,
mpc, pppoatm and atmtcp.
In svc_compat_ioctl() the only mangling which is needed is to change
COMPAT_ATM_ADDPARTY to ATM_ADDPARTY. Although it's defined as
_IOW('a', ATMIOC_SPECIAL+4,struct atm_iobuf)
it doesn't actually _take_ a struct atm_iobuf as an argument -- it takes
a struct sockaddr_atmsvc, which _is_ the same between 32-bit and 64-bit
code, so doesn't need conversion.
Almost all of vcc_ioctl() would have been identical, so I converted that
into a core do_vcc_ioctl() function with an 'int compat' argument.
I've done the same with atm_dev_ioctl(), where there _are_ a few
differences, but still it's relatively contained and there would
otherwise have been a lot of duplication.
I haven't done any of the actual device-specific ioctls, although I've
added a compat_ioctl method to struct atmdev_ops.
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Stephen Hemminger [Thu, 4 Dec 2008 06:10:38 +0000 (22:10 -0800)]
ne-h8300: convert to net_device_ops
Another device using 8390 library that needs converting.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Stephen Hemminger [Thu, 4 Dec 2008 06:10:10 +0000 (22:10 -0800)]
hydra: convert to net_device_ops
Another device using 8390 library that needs converting.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Stephen Hemminger [Thu, 4 Dec 2008 06:09:30 +0000 (22:09 -0800)]
zorro8390: convert to net_device_ops
Another device using 8390 library that needs converting.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Wang Chen [Thu, 4 Dec 2008 06:07:10 +0000 (22:07 -0800)]
e1000: e1000_adapter->polling_netdev is useless
Commit
bea3348eef27e6044b6161fd04c3152215f96411
"[NET]: Make NAPI polling independent of struct net_device objects."
made NAPI polling to be independent of net_device.
So e1000_adapter->polling_netdev is no longer used.
Kill it.
Signed-off-by: Wang Chen <wangchen@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Wang Chen [Thu, 4 Dec 2008 06:05:58 +0000 (22:05 -0800)]
ixgbe: function comment typo
Seems the ixgbe's code was copied from e1000.
The comment talks about something not exist.
Signed-off-by: Wang Chen <wangchen@cn.fujitsu.com>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ilpo Järvinen [Thu, 4 Dec 2008 05:24:48 +0000 (21:24 -0800)]
tcp: make urg+gso work for real this time
I should have noticed this earlier... :-) The previous solution
to URG+GSO/TSO will cause SACK block tcp_fragment to do zig-zig
patterns, or even worse, a steep downward slope into packet
counting because each skb pcount would be truncated to pcount
of 2 and then the following fragments of the later portion would
restore the window again.
Basically this reverts "tcp: Do not use TSO/GSO when there is
urgent data" (
33cf71cee1). It also removes some unnecessary code
from tcp_current_mss that didn't work as intented either (could
be that something was changed down the road, or it might have
been broken since the dawn of time) because it only works once
urg is already written while this bug shows up starting from
~64k before the urg point.
The retransmissions already are split to mss sized chunks, so
only new data sending paths need splitting in case they have
a segment otherwise suitable for gso/tso. The actually check
can be improved to be more narrow but since this is late -rc
already, I'll postpone thinking the more fine-grained things.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
Guo-Fu Tseng [Thu, 4 Dec 2008 05:20:04 +0000 (21:20 -0800)]
jme: Remove 64 and 40 bit dma_mask
Although the hardware supports the 64bit DMA address in design,
but later found that it actually not working.
This patch reduced the rang to 32bit.
Found-by: "Ethan" <ethanhsiao@jmicron.com>
Signed-off-by: "Guo-Fu Tseng" <cooldavid@cooldavid.org>
Acked-by: Jeff Garzik <jgarzik@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
akeemting [Thu, 4 Dec 2008 05:19:16 +0000 (21:19 -0800)]
jme: GHC register control fix for new hardware
Due to the hardware design, except the first chip on the market,
other chips needs to setup the clock source for MAC processor
implicitly through Global Host Control Register(GHC).
(Strange design huh?)
10/100M uses the PCI-E as clock source, and 1G uses GPHY.
And I reordered the code a little, to make it easier to read.
Found-by: "Ethan" <ethanhsiao@jmicron.com>
Fixed-by: "akeemting" <akeem@jmicron.com>
Signed-off-by: "Guo-Fu Tseng" <cooldavid@cooldavid.org>
Acked-by: Jeff Garzik <jgarzik@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jarek Poplawski [Thu, 4 Dec 2008 05:17:27 +0000 (21:17 -0800)]
pkt_sched: sch_htb: Replace HTB_ACCNT() macro with inlines
Replace HTB_ACCNT() macro with inlines to make it more readable.
Signed-off-by: Jarek Poplawski <jarkao2@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jarek Poplawski [Thu, 4 Dec 2008 05:16:58 +0000 (21:16 -0800)]
pkt_sched: sch_htb: Remove L2T()
L2T() is currently used only in one place (and has one spurious
parameter, btw), so let's: 'get rid of L2T completely, and just
use "qdisc_l2t(rate, size)" directly.' - quote & feedback from
David S. Miller.
Signed-off-by: Jarek Poplawski <jarkao2@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Baruch Siach [Tue, 2 Dec 2008 05:07:01 +0000 (05:07 +0000)]
enc28j60: Fix sporadic packet loss (corrected again)
Packet data read from the RX buffer the when the RSV is at the end of the RX
buffer does not warp around. This causes packet loss, as the actual data is
never read. Fix this by calculating the right packet data location.
Thanks to Shachar Shemesh for suggesting the fix.
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Acked-by: Claudio Lanconelli <lanconelli.claudio@eptar.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Wang Chen [Thu, 4 Dec 2008 05:14:04 +0000 (21:14 -0800)]
bond: Kill directly reference of netdev->priv
Simply replace netdev->priv with netdev_priv().
Signed-off-by: Wang Chen <wangchen@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Wang Chen [Thu, 4 Dec 2008 05:13:37 +0000 (21:13 -0800)]
mptlan: Kill directly reference of netdev->priv
Simply replace netdev->priv with netdev_priv().
Signed-off-by: Wang Chen <wangchen@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Wang Chen [Thu, 4 Dec 2008 05:13:13 +0000 (21:13 -0800)]
dvb: Kill directly reference of netdev->priv
Simply replace netdev->priv with netdev_priv().
Signed-off-by: Wang Chen <wangchen@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jarek Poplawski [Thu, 4 Dec 2008 05:09:45 +0000 (21:09 -0800)]
pkt_sched: sch_htb: Clean htb_class prio and quantum fields
While implementing htb_parent_to_leaf() there where added backup prio
and quantum struct htb_class fields to preserve these values for inner
classes in case of their return to leaf. This patch cleans this a bit
by removing union leaf duplicates.
Signed-off-by: Jarek Poplawski <jarkao2@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jarek Poplawski [Thu, 4 Dec 2008 05:09:10 +0000 (21:09 -0800)]
pkt_sched: sch_htb: Remove htb_sched nwc_hit field
Remove practically unused struct htb_sched nwc_hit field.
Signed-off-by: Jarek Poplawski <jarkao2@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jarek Poplawski [Thu, 4 Dec 2008 05:08:44 +0000 (21:08 -0800)]
pkt_sched: sch_htb: Remove htb_class aprio field
Remove practically unused struct htb_class aprio field.
Signed-off-by: Jarek Poplawski <jarkao2@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ed Swierk [Mon, 1 Dec 2008 12:24:43 +0000 (12:24 +0000)]
forcedeth: power down phy when interface is down
Bring the physical link down when the interface is down by placing the PHY
in power-down state, unless WOL is enabled. This mirrors the behavior of
other drivers including e1000 and tg3.
Without the patch, ifconfig down leaves the physical link up, which confuses
datacenter users who expect the link lights both on the NIC and the switch to
go out when they bring an interface down.
Furthermore, even though the phy is powered on, autonegotiation stops working,
so a normally gigabit link might suddenly become 100 Mbit half-duplex when the
interface goes down, and become gigabit when it comes up again.
Ayaz said:
I would not include this patch until further testing is performed. NVIDIA
MCP chips use 3rd party PHY vendors. By powering down the phy, it could
have adverse affects on certain phys.
Arthur Jones said:
I just ran across this patch. Tested on a Marvell 88E1121R (GigE PHY)
and works great. This is a very important feature for me.
Signed-off-by: Ed Swierk <eswierk@arastra.com>
Tested-by: Arthur Jones <ajones@riverbed.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Andrew Morton [Mon, 1 Dec 2008 12:24:46 +0000 (12:24 +0000)]
drivers/net/smc911x.c: smc911x_drv_probe() cleanup
Save an ugly ifdef.
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pascal Terjan [Mon, 1 Dec 2008 12:24:25 +0000 (12:24 +0000)]
hysdn: fix writing outside the field on 64 bits
ifa_local is assumed to be unsigned long which lead to writing the address
at dev->dev_addr-2 instead of +2
noticed thanks to gcc:
drivers/isdn/hysdn/hysdn_net.c: In function `net_open':
drivers/isdn/hysdn/hysdn_net.c:91: warning: array subscript is below array bounds
Signed-off-by: Pascal Terjan <pterjan@mandriva.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Julia Lawall [Mon, 1 Dec 2008 12:24:24 +0000 (12:24 +0000)]
drivers/isdn/mISDN: use ARRAY_SIZE
ARRAY_SIZE is more concise to use when the size of an array is divided by
the size of its type or the size of its first element.
The semantic patch that makes this change is as follows:
(http://www.emn.fr/x-info/coccinelle/)
// <smpl>
@i@
@@
#include <linux/kernel.h>
@depends on i using "paren.iso"@
type T;
T[] E;
@@
- (sizeof(E)/sizeof(T))
+ ARRAY_SIZE(E)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Wilfried Klaebe [Thu, 4 Dec 2008 04:57:19 +0000 (20:57 -0800)]
b1isa: fix b1isa_exit() to really remove registered capi controllers
On "/etc/init.d/capiutils stop", this oops happened.
The oops happens on reading /proc/capi/controllers because
capi_ctrl->procinfo is called for the wrongly not unregistered
controller, which points to b1isa_procinfo(), which was removed on
module unload.
b1isa_exit() did not call b1isa_remove() for its controllers because
io[0] == 0 on module unload despite having been 0x340 on module load.
Besides, just removing the controllers that where added on module
load time and not those that were added later via b1isa_add_card() is
wrong too - the place where all added cards are found is isa_dev[].
relevant dmesg lines:
[ 0.000000] Linux version 2.6.27.4 (w@shubashi) (gcc version 4.3.2 (Debian 4.3.2-1) ) #3 Thu Oct 30 16:49:03 CET 2008
[ 67.403555] CAPI Subsystem Rev 1.1.2.8
[ 68.529154] capifs: Rev 1.1.2.3
[ 68.563292] capi20: Rev 1.1.2.7: started up with major 68 (middleware+capifs)
[ 77.026936] b1: revision 1.1.2.2
[ 77.049992] b1isa: revision 1.1.2.3
[ 77.722655] kcapi: Controller [001]: b1isa-340 attached
[ 77.722671] b1isa: AVM B1 ISA at i/o 0x340, irq 5, revision 255
[ 81.272669] b1isa-340: card 1 "B1" ready.
[ 81.272683] b1isa-340: card 1 Protocol: DSS1
[ 81.272689] b1isa-340: card 1 Linetype: point to multipoint
[ 81.272695] b1isa-340: B1-card (3.11-03) now active
[ 81.272702] kcapi: card [001] "b1isa-340" ready.
[ 153.721281] kcapi: card [001] down.
[ 154.151889] BUG: unable to handle kernel paging request at
e87af000
[ 154.152081] IP: [<
e87af000>]
[ 154.153292] *pde =
2655b067 *pte =
00000000
[ 154.153307] Oops: 0000 [#1]
[ 154.153360] Modules linked in: rfcomm l2cap ppdev lp ipt_MASQUERADE tun capi capifs kernelcapi ac battery nfsd exportfs nfs lockd nfs_acl sunrpc sit tunnel4 bridge stp llc ipt_REJECT ipt_LOG xt_tcpudp xt_state iptable_filter iptable_mangle iptable_nat nf_nat nf_conntrack_ipv4 nf_conntrack ip_tables x_tables nls_utf8 isofs nls_base zlib_inflate loop ipv6 netconsole snd_via82xx dvb_usb_dib0700 gameport dib7000p dib7000m dvb_usb snd_ac97_codec ac97_bus dvb_core mt2266 snd_pcm tuner_xc2028 dib3000mc dibx000_common mt2060 dib0070 snd_page_alloc snd_mpu401_uart snd_seq_midi snd_seq_midi_event btusb snd_rawmidi bluetooth snd_seq snd_timer snd_seq_device snd via686a i2c_viapro soundcore i2c_core parport_pc parport button dm_mirror dm_log dm_snapshot floppy sg ohci1394 uhci_hcd ehci_hcd 8139too mii ieee1394 usbcore sr_mod cdrom sd_mod thermal processor fan [last unloaded: b1]
[ 154.153360]
[ 154.153360] Pid: 4132, comm: capiinit Not tainted (2.6.27.4 #3)
[ 154.153360] EIP: 0060:[<
e87af000>] EFLAGS:
00010286 CPU: 0
[ 154.153360] EIP is at 0xe87af000
[ 154.153360] EAX:
e6b9ccc8 EBX:
e6b9ccc8 ECX:
e87a0c67 EDX:
e87af000
[ 154.153360] ESI:
e142bbc0 EDI:
e87a56e0 EBP:
e0505f0c ESP:
e0505ee4
[ 154.153360] DS: 007b ES: 007b FS: 0000 GS: 0033 SS: 0068
[ 154.153360] Process capiinit (pid: 4132, ti=
e0504000 task=
d1196cf0 task.ti=
e0504000)
[ 154.153360] Stack:
e879f650 00000246 e0505ef4 c01472eb e0505f0c 00000246 e7001780 fffffff4
[ 154.153360]
fffffff4 e142bbc0 e0505f48 c01a56c6 00000400 b805e000 d102dc80 e142bbe0
[ 154.153360]
00000000 e87a56e0 00000246 e12617ac 00000000 00000000 e1261760 fffffffb
[ 154.153360] Call Trace:
[ 154.153360] [<
e879f650>] ? controller_show+0x20/0x90 [kernelcapi]
[ 154.153360] [<
c01472eb>] ? trace_hardirqs_on+0xb/0x10
[ 154.153360] [<
c01a56c6>] ? seq_read+0x126/0x2f0
[ 154.153360] [<
c01a55a0>] ? seq_read+0x0/0x2f0
[ 154.153360] [<
c01c033c>] ? proc_reg_read+0x5c/0x90
[ 154.153360] [<
c0189919>] ? vfs_read+0x99/0x140
[ 154.153360] [<
c01c02e0>] ? proc_reg_read+0x0/0x90
[ 154.153360] [<
c0189a7d>] ? sys_read+0x3d/0x70
[ 154.153360] [<
c0103c3d>] ? sysenter_do_call+0x12/0x35
[ 154.153360] =======================
[ 154.153360] Code: Bad EIP value.
[ 154.153360] EIP: [<
e87af000>] 0xe87af000 SS:ESP 0068:
e0505ee4
[ 154.153360] ---[ end trace
23750b6c2862de94 ]---
Signed-off-by: Wilfried Klaebe <linux-kernel@lebenslange-mailadresse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Acked-by: Karsten Keil <kkeil@suse.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Oliver Hartkopp [Wed, 3 Dec 2008 23:52:35 +0000 (15:52 -0800)]
can: Fix CAN_(EFF|RTR)_FLAG handling in can_filter
Due to a wrong safety check in af_can.c it was not possible to filter
for SFF frames with a specific CAN identifier without getting the
same selected CAN identifier from a received EFF frame also.
This fix has a minimum (but user visible) impact on the CAN filter
API and therefore the CAN version is set to a new date.
Indeed the 'old' API is still working as-is. But when now setting
CAN_(EFF|RTR)_FLAG in can_filter.can_mask you might get less traffic
than before - but still the stuff that you expected to get for your
defined filter ...
Thanks to Kurt Van Dijck for pointing at this issue and for the review.
Signed-off-by: Oliver Hartkopp <oliver@hartkopp.net>
Acked-by: Kurt Van Dijck <kurt.van.dijck@eia.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
Wang Chen [Wed, 3 Dec 2008 23:49:46 +0000 (15:49 -0800)]
isdn: Kill directly reference of netdev->priv
Simply use netdev_priv() to replace netdev->priv.
Signed-off-by: Wang Chen <wangchen@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Wang Chen [Wed, 3 Dec 2008 23:49:07 +0000 (15:49 -0800)]
hysdn: Kill directly reference of netdev->priv
Usually, netdev->priv should point to the memory of private
data which is allocated in alloc_netdev().
netdev_priv() is used to get the address of the private data.
Change the netdev->priv pointer to another memory is wrong.
Use netdev->ml_priv for this case.
Signed-off-by: Wang Chen <wangchen@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
RĂ©mi Denis-Courmont [Wed, 3 Dec 2008 23:42:56 +0000 (15:42 -0800)]
Phonet: basic net namespace support
Signed-off-by: RĂ©mi Denis-Courmont <remi.denis-courmont@nokia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
remi.denis-courmont@nokia [Mon, 1 Dec 2008 02:37:20 +0000 (02:37 +0000)]
Phonet: do not dump addresses from other namespaces
Signed-off-by: RĂ©mi Denis-Courmont <remi.denis-courmont@nokia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Martin Willi [Wed, 3 Dec 2008 23:38:07 +0000 (15:38 -0800)]
xfrm: Accept XFRM_STATE_AF_UNSPEC SAs on IPv4/IPv6 only hosts
Installing SAs using the XFRM_STATE_AF_UNSPEC fails on hosts with
support for one address family only. This patch accepts such SAs, even
if the processing of not supported packets will fail.
Signed-off-by: Martin Willi <martin@strongswan.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Paul Moore [Wed, 3 Dec 2008 08:37:04 +0000 (00:37 -0800)]
netlabel: Fix a potential NULL pointer dereference
Fix a potential NULL pointer dereference seen when trying to remove a
static label configuration with an invalid address/mask combination.
Signed-off-by: Paul Moore <paul.moore@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Michael Chan [Wed, 3 Dec 2008 08:36:15 +0000 (00:36 -0800)]
bnx2: Add workaround to handle missed MSI.
The bnx2 chips do not support per MSI vector masking. On 5706/5708, new MSI
address/data are stored only when the MSI enable bit is toggled. As a result,
SMP affinity no longer works in the latest kernel. A more serious problem is
that the driver will no longer receive interrupts when the MSI receiving CPU
goes offline.
The workaround in this patch only addresses the problem of CPU going offline.
When that happens, the driver's timer function will detect that it is making
no forward progress on pending interrupt events and will recover from it.
Eric Dumazet reported the problem.
We also found that if an interrupt is internally asserted while MSI and INTA
are disabled, the chip will end up in the same state after MSI is re-enabled.
The same workaround is needed for this problem.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Tested-by: Eric Dumazet <dada1@cosmosbay.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Wei Yongjun [Wed, 3 Dec 2008 08:33:09 +0000 (00:33 -0800)]
xfrm: Cleanup for unlink SPD entry
Used __xfrm_policy_unlink() to instead of the dup codes when unlink
SPD entry.
Signed-off-by: Wei Yongjun <yjwei@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Wed, 3 Dec 2008 08:29:24 +0000 (00:29 -0800)]
Merge branch 'master' of /linux/kernel/git/davem/net-2.6
Wei Yongjun [Wed, 3 Dec 2008 08:27:18 +0000 (00:27 -0800)]
xfrm: Fix kernel panic when flush and dump SPD entries
After flush the SPD entries, dump the SPD entries will cause kernel painc.
Used the following commands to reproduct:
- echo 'spdflush;' | setkey -c
- echo 'spdadd 3ffe:501:ffff:ff01::/64 3ffe:501:ffff:ff04::/64 any -P out ipsec \
ah/tunnel/3ffe:501:ffff:ff00:200:ff:fe00:b0b0-3ffe:501:ffff:ff02:200:ff:fe00:a1a1/require;\
spddump;' | setkey -c
- echo 'spdflush; spddump;' | setkey -c
- echo 'spdadd 3ffe:501:ffff:ff01::/64 3ffe:501:ffff:ff04::/64 any -P out ipsec \
ah/tunnel/3ffe:501:ffff:ff00:200:ff:fe00:b0b0-3ffe:501:ffff:ff02:200:ff:fe00:a1a1/require;\
spddump;' | setkey -c
This is because when flush the SPD entries, the SPD entry is not remove
from the list.
This patch fix the problem by remove the SPD entry from the list.
Signed-off-by: Wei Yongjun <yjwei@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Wed, 3 Dec 2008 06:38:02 +0000 (22:38 -0800)]
Merge branch 'master' of git://git./linux/kernel/git/holtmann/bluetooth-next-2.6
David S. Miller [Wed, 3 Dec 2008 03:50:27 +0000 (19:50 -0800)]
Merge branch 'master' of /linux/kernel/git/davem/net-2.6
Conflicts:
drivers/net/ixgbe/ixgbe_main.c
drivers/net/smc91x.c
Linus Torvalds [Tue, 2 Dec 2008 23:58:20 +0000 (15:58 -0800)]
Merge git://git./linux/kernel/git/wim/linux-2.6-watchdog
* git://git.kernel.org/pub/scm/linux/kernel/git/wim/linux-2.6-watchdog:
[WATCHDOG] hpwdt: Fix kdump when using hpwdt
[WATCHDOG] hpwdt: set the mapped BIOS address space as executable
[WATCHDOG] iTCO_wdt: add PCI ID's for ICH9 & ICH10 chipsets
[WATCHDOG] iTCO_wdt : correct status clearing
[WATCHDOG] iTCO_wdt : problem with rebooting on new ICH9 based motherboards
[WATCHDOG] fix mtx1_wdt compilation failure
Linus Torvalds [Tue, 2 Dec 2008 23:56:55 +0000 (15:56 -0800)]
Merge branch 'linux-next' of git://git.infradead.org/ubifs-2.6
* 'linux-next' of git://git.infradead.org/ubifs-2.6:
UBIFS: pre-allocate bulk-read buffer
UBIFS: do not allocate too much
UBIFS: do not print scary memory allocation warnings
UBIFS: allow for gaps when dirtying the LPT
UBIFS: fix compilation warnings
MAINTAINERS: change UBI/UBIFS git tree URLs
UBIFS: endian handling fixes and annotations
UBIFS: remove printk
Linus Torvalds [Tue, 2 Dec 2008 23:56:17 +0000 (15:56 -0800)]
Merge branch 'kvm-updates/2.6.28' of git://git./linux/kernel/git/avi/kvm
* 'kvm-updates/2.6.28' of git://git.kernel.org/pub/scm/linux/kernel/git/avi/kvm:
KVM: MMU: avoid creation of unreachable pages in the shadow
KVM: ppc: stop leaking host memory on VM exit
KVM: MMU: fix sync of ptes addressed at owner pagetable
KVM: ia64: Fix: Use correct calling convention for PAL_VPS_RESUME_HANDLER
KVM: ia64: Fix incorrect kbuild CFLAGS override
KVM: VMX: Fix interrupt loss during race with NMI
KVM: s390: Fix problem state handling in guest sigp handler
Linus Torvalds [Tue, 2 Dec 2008 23:55:43 +0000 (15:55 -0800)]
Merge git://git./linux/kernel/git/davem/sparc-2.6
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc-2.6:
sparc64: Fix offset calculation in compute_size()
rtc: rtc-starfire fixes
Linus Torvalds [Tue, 2 Dec 2008 23:55:05 +0000 (15:55 -0800)]
Merge git://git./linux/kernel/git/davem/net-2.6
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (30 commits)
MAINTAINERS: add netdev to ATM
ATM: horizon, fix hrz_probe fail path
pppol2tp: Add missing sock_put() in pppol2tp_release()
net: Fix soft lockups/OOM issues w/ unix garbage collector
macvlan: don't broadcast PAUSE frames to macvlan devices
Phonet: fix oops in phonet_address_del() on non-Phonet device
netfilter: ctnetlink: fix GFP_KERNEL allocation under spinlock
sungem: Fix PCS_MIICTRL register write in gem_init_phy().
net: make skb_truesize_bug() call WARN()
net: hp-plus uses eip_poll
net/wireless/reg.c: fix bad WARN_ON in if statement
ath5k: disable beacon filter when station is not associated
ath5k: fix Security issue in DebugFS part of ath5k
ath9k: correct expected max RX buffer size
ath9k: Fix SW-IOMMU bounce buffer starvation
mac80211 : Fix setting ad-hoc mode and non-ibss channel
iwlagn: fix DMA sync
phylib: Add Vitesse VSC8221 SGMII PHY
rose: zero length frame filtering in af_rose.c
bridge: netfilter: fix update_pmtu crash with GRE
...
Linus Torvalds [Tue, 2 Dec 2008 23:53:41 +0000 (15:53 -0800)]
Merge branch 'for-linus' of git://git./linux/kernel/git/geert/linux-m68k
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/linux-m68k:
m68k: Update defconfigs for 2.6.28-rc7
macfb: Do not overflow fb_fix_screeninfo.id
Linus Torvalds [Tue, 2 Dec 2008 23:53:10 +0000 (15:53 -0800)]
Merge git://git./linux/kernel/git/bart/ide-2.6
* git://git.kernel.org/pub/scm/linux/kernel/git/bart/ide-2.6:
alim15x3: fix sparse warning
ide: remove dead code from drive_is_ready()
ide: fix build for DEBUG_PM
ide: respect current DMA setting during resume
ide: add SAMSUNG SP0822N with firmware WA100-10 to ivb_list[]
amd74xx: workaround unreliable AltStatus register for nVidia controllers
ide: fix the ide_release_lock imbalance
Linus Torvalds [Tue, 2 Dec 2008 23:52:28 +0000 (15:52 -0800)]
Merge git://git./linux/kernel/git/jejb/scsi-rc-fixes-2.6
* git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-rc-fixes-2.6:
[SCSI] stex: switch to block timeout
[SCSI] make scsi_eh_try_stu use block timeout
[SCSI] megaraid_sas: switch to block timeout
[SCSI] ibmvscsi: switch to block timeout
[SCSI] aacraid: switch to block timeout
[SCSI] zfcp: prevent double decrement on host_busy while being busy
[SCSI] zfcp: fix deadlock between wq triggered port scan and ERP
[SCSI] zfcp: eliminate race between validation and locking
[SCSI] zfcp: verify for correct rport state before scanning for SCSI devs
[SCSI] zfcp: returning an ERR_PTR where a NULL value is expected
[SCSI] zfcp: Fix opening of wka ports
[SCSI] zfcp: fix remote port status check
[SCSI] fc_transport: fix old bug on bitflag definitions
[SCSI] Fix hang in starved list processing
Mark Salter [Tue, 2 Dec 2008 14:38:09 +0000 (14:38 +0000)]
MN10300: Fix application of kernel module relocations
This fixes the MN10300 kernel module linking to match the toolchain. RELA
relocs don't use the value at the location being relocated. This has been
working because the tools always leave the value at the target location
cleared.
Signed-off-by: Mark Salter <msalter@redhat.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Dean Nelson [Tue, 2 Dec 2008 14:06:01 +0000 (08:06 -0600)]
sgi-gru: call fs_initcall() if statically linked
If xpc.ko and gru.ko are both statically linked into the kernel, then
xpc_init() can get called before gru_init() and make a call to one of the
gru's exported functions before the gru has initialized itself. The end
result is a NULL dereference.
Signed-off-by: Dean Nelson <dcn@sgi.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Kumar Gala [Tue, 2 Dec 2008 19:37:01 +0000 (13:37 -0600)]
powerpc: Use physical cpu id when setting the processor affinity
In the CONFIG_SMP case the irq_choose_cpu() code was returning back
a logical cpu id not the physical id. We were writing that directly
into the HW register.
We need to be calling get_hard_smp_processor_id() so irq_choose_cpu()
always returns a physical cpu id.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Rik van Riel [Tue, 2 Dec 2008 18:31:52 +0000 (10:31 -0800)]
vmscan: evict streaming IO first
Count the insertion of new pages in the statistics used to drive the
pageout scanning code. This should help the kernel quickly evict
streaming file IO.
We count on the fact that new file pages start on the inactive file LRU
and new anonymous pages start on the active anon list. This means
streaming file IO will increment the recent scanned file statistic, while
leaving the recent rotated file statistic alone, driving pageout scanning
to the file LRUs.
Pageout activity does its own list manipulation.
Signed-off-by: Rik van Riel <riel@redhat.com>
Cc: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Tested-by: Gene Heskett <gene.heskett@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Kay Sievers [Tue, 2 Dec 2008 18:31:50 +0000 (10:31 -0800)]
bdi: register sysfs bdi device only once per queue
Devices which share the same queue, like floppies and mtd devices, get
registered multiple times in the bdi interface, but bdi accounts only the
last registered device of the devices sharing one queue.
On remove, all earlier registered devices leak, stay around in sysfs, and
cause "duplicate filename" errors if the devices are re-created.
This prevents the creation of multiple bdi interfaces per queue, and the
bdi device will carry the dev_t name of the block device which is the
first one registered, of the pool of devices using the same queue.
[akpm@linux-foundation.org: add a WARN_ON so we know which drivers are misbehaving]
Tested-by: Peter Korsgaard <jacmet@sunsite.dk>
Acked-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
Cc: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Junjiro R. Okajima [Tue, 2 Dec 2008 18:31:46 +0000 (10:31 -0800)]
nfsd: fix vm overcommit crash fix #2
The previous patch from Alan Cox ("nfsd: fix vm overcommit crash",
commit
731572d39fcd3498702eda4600db4c43d51e0b26) fixed the problem where
knfsd crashes on exported shmemfs objects and strict overcommit is set.
But the patch forgot supporting the case when CONFIG_SECURITY is
disabled.
This patch copies a part of his fix which is mainly for detecting a bug
earlier.
Acked-by: James Morris <jmorris@namei.org>
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Junjiro R. Okajima <hooanon05@yahoo.co.jp>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
David S. Miller [Tue, 2 Dec 2008 23:05:06 +0000 (15:05 -0800)]
Merge branch 'master' of ssh:///linux/kernel/git/rusty/linux-2.6-for-linus
Stephen Hemminger [Tue, 2 Dec 2008 23:00:28 +0000 (15:00 -0800)]
mac8390: update to net_device_ops
Another related 8390 driver. Since this is for nubus, not sure if
anyone still has the hardware?
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Stephen Hemminger [Tue, 2 Dec 2008 22:52:25 +0000 (14:52 -0800)]
etherh: build fix for net-next
Fix build of ARM etherh driver with new net_device_ops.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Geert Uytterhoeven [Tue, 2 Dec 2008 19:58:26 +0000 (20:58 +0100)]
m68k: Update defconfigs for 2.6.28-rc7
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Hannes Eder [Tue, 2 Dec 2008 19:40:04 +0000 (20:40 +0100)]
alim15x3: fix sparse warning
Fix this sparse warning:
drivers/ide/alim15x3.c:594:2: warning: returning void-valued expression
Signed-off-by: Hannes Eder <hannes@hanneseder.net>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Bartlomiej Zolnierkiewicz [Tue, 2 Dec 2008 19:40:04 +0000 (20:40 +0100)]
ide: remove dead code from drive_is_ready()
We guarantee 400ns delay at the time of issuing the command.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Bartlomiej Zolnierkiewicz [Tue, 2 Dec 2008 19:40:03 +0000 (20:40 +0100)]
ide: fix build for DEBUG_PM
Also while at it:
* Drop unused arguments from ide_complete_power_step().
* Move DEBUG_PM printk() from ide_end_drive_cmd() to
ide_complete_power_step().
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Bartlomiej Zolnierkiewicz [Tue, 2 Dec 2008 19:40:03 +0000 (20:40 +0100)]
ide: respect current DMA setting during resume
Respect current DMA setting during resume, otherwise PIO timings
may get destroyed if host uses shared PIO/MWDMA timings.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Bartlomiej Zolnierkiewicz [Tue, 2 Dec 2008 19:40:03 +0000 (20:40 +0100)]
ide: add SAMSUNG SP0822N with firmware WA100-10 to ivb_list[]
Should fix kernel.org bug #10225:
http://bugzilla.kernel.org/show_bug.cgi?id=10225
Reported-by: Matthias B. <haferfrost@web.de>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Acked-by: Sergei Shtyltov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Bartlomiej Zolnierkiewicz [Tue, 2 Dec 2008 19:40:03 +0000 (20:40 +0100)]
amd74xx: workaround unreliable AltStatus register for nVidia controllers
It seems that on some nVidia controllers using AltStatus register
can be unreliable so default to Status register if the PCI device
is in Compatibility Mode. In order to achieve this:
* Add ide_pci_is_in_compatibility_mode() inline helper to <linux/ide.h>.
* Add IDE_HFLAG_BROKEN_ALTSTATUS host flag and set it in amd74xx host
driver for nVidia controllers in Compatibility Mode.
* Teach actual_try_to_identify() and drive_is_ready() about the new flag.
This fixes the regression caused by removal of CONFIG_IDEPCI_SHARE_IRQ
config option in 2.6.25 and using AltStatus register unconditionally when
available (kernel.org bugs #11659 and #10216).
[ Moreover for CONFIG_IDEPCI_SHARE_IRQ=y (which is what most people
and distributions use) it never worked correctly. ]
Thanks to Remy LABENE and Lars Winterfeld for help with debugging the problem.
More info at:
http://bugzilla.kernel.org/show_bug.cgi?id=11659
http://bugzilla.kernel.org/show_bug.cgi?id=10216
Reported-by: Remy LABENE <remy.labene@free.fr>
Tested-by: Remy LABENE <remy.labene@free.fr>
Tested-by: Lars Winterfeld <lars.winterfeld@tu-ilmenau.de>
Acked-by: Borislav Petkov <petkovbb@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Michael Schmitz [Tue, 2 Dec 2008 19:40:02 +0000 (20:40 +0100)]
ide: fix the ide_release_lock imbalance
ide_release_lock() spits out lots of:
ide_release_lock: bug
warnings on Atari Falcon.
Fix the ide_release_lock imbalance.
Signed-off-by: Michael Schmitz <schmitz@biophys.uni-duesseldorf.de>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Finn Thain [Tue, 18 Nov 2008 19:40:40 +0000 (20:40 +0100)]
macfb: Do not overflow fb_fix_screeninfo.id
Don't overflow the 16-character fb_fix_screeninfo id string (fixes some
console erasing and blanking artifacts). Have the ID default to "Unknown"
on machines with no built-in video and no nubus devices. Check for
fb_alloc_cmap failure.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Mark McLoughlin [Wed, 26 Nov 2008 13:58:11 +0000 (13:58 +0000)]
virtio_net: large tx MTU support
We don't really have a max tx packet size limit, so allow configuring
the device with up to 64k tx MTU.
Signed-off-by: Mark McLoughlin <markmc@redhat.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Eric Dumazet [Tue, 2 Dec 2008 07:37:17 +0000 (23:37 -0800)]
net: percpu_counter_inc() should not be called in BH-disabled section
Based upon a lockdep report by Alexey Dobriyan.
I checked all per_cpu_counter_xxx() usages in network tree, and I
think all call sites are BH enabled except one in
inet_csk_listen_stop().
commit
dd24c00191d5e4a1ae896aafe33c6b8095ab4bd1
(net: Use a percpu_counter for orphan_count)
replaced atomic_t orphan_count to a percpu_counter.
atomic_inc()/atomic_dec() can be called from any context, while
percpu_counter_xxx() should be called from a consistent state.
For orphan_count, this context can be the BH-enabled one.
Signed-off-by: Eric Dumazet <dada1@cosmosbay.com>
Signed-off-by: David S. Miller <davem@davemloft.net>