Paul Mundt [Tue, 25 Nov 2008 18:44:07 +0000 (03:44 +0900)] 
sh: More movmem alias symbol exports for older compilers.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Paul Mundt [Tue, 25 Nov 2008 15:29:58 +0000 (00:29 +0900)]
sh: Provide optimized unaligned loads on SH-4A.
This adds support for unaligned loads on SH-4A, using the SH-4A's
neutered movua.l instruction. As movua.l is r0-inspired, stores are
still handled through the packed struct.
Based on asm-generic/unaligned.h by Harvey Harrison.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Magnus Damm [Tue, 25 Nov 2008 12:57:29 +0000 (21:57 +0900)] 
sh: P4 ioremap pass-through
This patch adds a pass-through case when ioremapping P4 addresses.
Addresses passed to ioremap() should be physical addresses, so the
best option is usually to convert the virtual address to a physical
address before calling ioremap. This will give you a virtual address
in P2 which matches the physical address and this works well for
most internal hardware blocks on the SuperH architecture.
However, some hardware blocks must be accessed through P4. Converting
the P4 address to a physical and then back to a P2 does not work. One
example of this is the sh7722 TMU block, it must be accessed through P4.
Without this patch P4 addresses will be mapped using PTEs which
requires the page allocator to be up and running.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Michael Trimarchi [Tue, 25 Nov 2008 12:37:14 +0000 (21:37 +0900)] 
sh: Add SH-4A optimized fastpath mutex implementation.
Add fast mutex path implementation for the SH4A architecture
Signed-off-by: Michael Trimarchi <trimarchimichael@yahoo.it>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Nobuhiro Iwamatsu [Fri, 21 Nov 2008 05:35:29 +0000 (14:35 +0900)] 
sh: sh7760fb: Add support SH7720/SH7721 of Renesas
SH7720 and 7721 has IP of Frame Buffer same as SH7760.
This driver can support these.
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Nobuhiro Iwamatsu [Fri, 21 Nov 2008 05:34:25 +0000 (14:34 +0900)]
sh: sh7760fb: Fix color pallette setting
The setting of the color palette was wrong, fixed it.
And removed fb_setcmap, and added fb_setcolreg function.
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Steve Glendinning [Sun, 23 Nov 2008 15:00:31 +0000 (15:00 +0000)] 
sh: add SH DMAC burst mode constant
The SH7709 datasheet defines bit 5 as set for burst mode, clear for
cycle-steal mode.
Signed-off-by: Steve Glendinning <steve.glendinning@smsc.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Steve Glendinning [Sun, 23 Nov 2008 14:27:22 +0000 (14:27 +0000)]
sh: fix DMAOR register access on SH7709
sh7709 hardware manual says DMAOR is 16 bits long on this platform.
Tested and working with a modified smsc911x ethernet driver (sh-dma
support patch for this driver is coming soon).
Signed-off-by: Steve Glendinning <steve.glendinning@smsc.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Steve Glendinning [Sun, 23 Nov 2008 14:27:21 +0000 (14:27 +0000)]
sh: Add platform-specific constants for SH7709
I'm using these constants in support of an in-house development board,
and thought they may be useful to other users of SH7709.
Signed-off-by: Steve Glendinning <steve.glendinning@smsc.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Paul Mundt [Tue, 25 Nov 2008 12:22:02 +0000 (21:22 +0900)]
sh: Provide optimized non-atomic bitops for SH-2A.
This ties in the new SH-2A 32-bit non-atomic bitops.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Paul Mundt [Thu, 20 Nov 2008 06:28:47 +0000 (15:28 +0900)]
sh: Add -m4al tuning for SH4AL-DSP.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Paul Mundt [Thu, 20 Nov 2008 06:26:35 +0000 (15:26 +0900)]
sh: Add exports for __udivsi3/__sdivsi3 and the _i4 versions.
Needed by older compilers.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Paul Mundt [Thu, 20 Nov 2008 06:25:22 +0000 (15:25 +0900)]
sh: Convert to generic bitops for IRQ-toggling implementation.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Paul Mundt [Tue, 18 Nov 2008 08:35:45 +0000 (17:35 +0900)]
sh: Specify sane default image targets for the SH-2 platforms.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Paul Mundt [Tue, 18 Nov 2008 08:33:48 +0000 (17:33 +0900)]
sh: Migrate necessary libgcc bits in to arch/sh/lib for SUPERH32.
This moves in the necessary libgcc bits for SUPERH32 and drops the
libgcc linking for the regular targets. This in turn allows us to rip
out quite a few hacks both in sh_ksyms_32 and arch/sh/Makefile.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Paul Mundt [Tue, 18 Nov 2008 05:22:39 +0000 (14:22 +0900)]
sh: __udivdi3 -> do_div() in softfloat lib.
Inhibit the generation of __udivdi3 for the softfloat lib, use do_div()
outright.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Paul Mundt [Tue, 18 Nov 2008 05:21:34 +0000 (14:21 +0900)]
sh: Fix clock framework compiler warnings.
CC arch/sh/kernel/cpu/clock.o
arch/sh/kernel/cpu/clock.c: In function 'clk_disable':
arch/sh/kernel/cpu/clock.c:156: warning: 'return' with a value, in function returning void
Introduced by ("sh: enable and disable clocks recursively").
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Paul Mundt [Tue, 18 Nov 2008 03:40:39 +0000 (12:40 +0900)]
usb: Fix up sh_mobile usbf clock framework warnings.
drivers/usb/gadget/m66592-udc.c: In function 'm66592_probe':
drivers/usb/gadget/m66592-udc.c:1672: warning: label 'clean_up2' defined but not used
drivers/usb/host/r8a66597-hcd.c: In function 'r8a66597_probe':
drivers/usb/host/r8a66597-hcd.c:2401: warning: label 'clean_up2' defined but not used
Added by commit
985fc7c81c7852f2e104c71cbe913ace683c9e6a ("sh: sh_mobile
usbf clock framework support").
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Michael Trimarchi [Thu, 13 Nov 2008 09:18:35 +0000 (18:18 +0900)]
serial: sh-sci: Codestyle cleanup patch.
Trivial coding style cleanups.
Signed-off-by: Michael Trimarchi <trimarchimichael@yahoo.it>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Paul Mundt [Thu, 13 Nov 2008 03:20:26 +0000 (12:20 +0900)]
media: sh_mobile_ceu_camera: Add HAVE_CLK dependency.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Matt Fleming [Wed, 12 Nov 2008 11:11:47 +0000 (20:11 +0900)] 
sh: dynamic ftrace support.
First cut at dynamic ftrace support.
Signed-off-by: Matt Fleming <mjf@gentoo.org>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Magnus Damm [Fri, 31 Oct 2008 11:24:01 +0000 (20:24 +0900)]
sh: remove old sh_mobile mstpc clocks
Remove the old sh_mobile mstpcr clocks.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Magnus Damm [Fri, 31 Oct 2008 11:23:26 +0000 (20:23 +0900)]
sh: sh_mobile lcdc clock framework support
Add clock framework support to the lcdc driver and
adjust the board specific code accordingly.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Magnus Damm [Fri, 31 Oct 2008 11:22:38 +0000 (20:22 +0900)]
sh: sh_mobile usb clock framework support
Add clock framework support to the usb/r8a66597 driver and
adjust the cpu specific code accordingly.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Magnus Damm [Fri, 31 Oct 2008 11:22:13 +0000 (20:22 +0900)]
sh: sh_mobile usbf clock framework support
Add clock framework support to the usbf/m66592 driver and
adjust the cpu specific code accordingly.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Magnus Damm [Fri, 31 Oct 2008 11:21:44 +0000 (20:21 +0900)]
sh: sh_mobile ceu clock framework support
Add clock framework support to the sh_mobile ceu and
adjust the board specific code accordingly.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Magnus Damm [Fri, 31 Oct 2008 11:21:23 +0000 (20:21 +0900)]
sh: sh_mobile keysc clock framework support
Add clock framework support to the sh_mobile keysc driver and
adjust the board specific code accordingly.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Magnus Damm [Fri, 31 Oct 2008 11:20:55 +0000 (20:20 +0900)]
sh: sh_mobile i2c clock framework support
Add clock framework support to the sh_mobile i2c driver and
adjust the processor specific code accordingly.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Magnus Damm [Fri, 31 Oct 2008 11:20:23 +0000 (20:20 +0900)]
sh: sh_mobile mstpcr clocks for sh7366
Add sh7366 mstpcr bits and information about their parent clocks.
The datasheet is pretty clear about the clocks on this device.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Magnus Damm [Fri, 31 Oct 2008 11:19:38 +0000 (20:19 +0900)]
sh: sh_mobile mstpcr clocks for sh7343
Add sh7343 mstpcr bits and information about their parent clocks.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Magnus Damm [Fri, 31 Oct 2008 11:16:08 +0000 (20:16 +0900)]
sh: sh_mobile mstpcr clocks for sh7723
Add sh7723 mstpcr bits and information about their parent clocks.
The datasheet is pretty clear about the clocks on this device.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Magnus Damm [Fri, 31 Oct 2008 11:15:48 +0000 (20:15 +0900)]
sh: sh_mobile mstpcr clocks for sh7722
Add sh7722 mstpcr bits and information about their parent clocks.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Magnus Damm [Fri, 31 Oct 2008 11:15:07 +0000 (20:15 +0900)]
sh: new sh_mobile mstpcr clocks base code
Add base code to handle new mstpcr clocks. Make sure clock rates propagate.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Magnus Damm [Fri, 31 Oct 2008 11:14:28 +0000 (20:14 +0900)]
sh: use arch_flags for sh_mobile mstpcr clock bits
Use arch_flags to keep track of register and flag number.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Magnus Damm [Fri, 31 Oct 2008 11:14:03 +0000 (20:14 +0900)]
sh: sh_mobile clock divider index fix
Use divider index value instead of divider value.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Magnus Damm [Fri, 31 Oct 2008 11:13:32 +0000 (20:13 +0900)]
sh: enable and disable clocks recursively
Recurse and make sure parent clocks get enabled/disabled.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Paul Mundt [Wed, 12 Nov 2008 04:17:38 +0000 (13:17 +0900)]
sh: Move arch_get_unmapped_area() in to arch/sh/mm/mmap.c.
Now that arch/sh/mm/mmap.c exists, move arch_get_unmapped_area() there.
Follows the ARM change.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Thomas Gleixner [Sat, 20 Dec 2008 20:27:34 +0000 (21:27 +0100)] 
Null pointer deref with hrtimer_try_to_cancel()
Impact: Prevent kernel crash with posix timer clockid CLOCK_MONOTONIC_RAW
commit
2d42244ae71d6c7b0884b5664cf2eda30fb2ae68 (clocksource:
introduce CLOCK_MONOTONIC_RAW) introduced a new clockid, which is only
available to read out the raw not NTP adjusted system time.
The above commit did not prevent that a posix timer can be created
with that clockid. The timer_create() syscall succeeds and initializes
the timer to a non existing hrtimer base. When the timer is deleted
either by timer_delete() or by the exit() cleanup the kernel crashes.
Prevent the creation of timers for CLOCK_MONOTONIC_RAW by setting the
posix clock function to no_timer_create which returns an error code.
Reported-and-tested-by: Eric Sesterhenn <snakebyte@gmx.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Oleg Nesterov <oleg@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Sat, 20 Dec 2008 19:07:31 +0000 (11:07 -0800)] 
Merge branch 'for-linus' of git://git./linux/kernel/git/ericvh/v9fs
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ericvh/v9fs:
fs/9p: change simple_strtol to simple_strtoul
9p: convert d_iname references to d_name.name
9p: Remove potentially bad parameter from function entry debug print.
Linus Torvalds [Sat, 20 Dec 2008 19:07:18 +0000 (11:07 -0800)]
Merge branch 'x86-fixes-for-linus' of git://git./linux/kernel/git/tip/linux-2.6-tip
* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86: fix resume (S2R) broken by Intel microcode module, on A110L
x86 gart: don't complain if no AMD GART found
AMD IOMMU: panic if completion wait loop fails
AMD IOMMU: set cmd buffer pointers to zero manually
x86: re-enable MCE on secondary CPUS after suspend/resume
AMD IOMMU: allocate rlookup_table with __GFP_ZERO
Dmitry Adamushko [Fri, 19 Dec 2008 23:15:24 +0000 (00:15 +0100)] 
x86: fix resume (S2R) broken by Intel microcode module, on A110L
Impact: fix deadlock
This is in response to the following bug report:
Bug-Entry : http://bugzilla.kernel.org/show_bug.cgi?id=12100
Subject : resume (S2R) broken by Intel microcode module, on A110L
Submitter : Andreas Mohr <andi@lisas.de>
Date : 2008-11-25 08:48 (19 days old)
Handled-By : Dmitry Adamushko <dmitry.adamushko@gmail.com>
[ The deadlock scenario has been discovered by Andreas Mohr ]
I think I might have a logical explanation why the system:
(http://bugzilla.kernel.org/show_bug.cgi?id=12100)
might hang upon resuming, OTOH it should have likely hanged each and every time.
(1) possible deadlock in microcode_resume_cpu() if either 'if' section is
taken;
(2) now, I don't see it in spec. and can't experimentally verify it (newer
ucodes don't seem to be available for my Core2duo)... but logically-wise, I'd
think that when read upon resuming, the 'microcode revision' (MSR 0x8B) should
be back to its original one (we need to reload ucode anyway so it doesn't seem
logical if a cpu doesn't drop the version)... if so, the comparison with
memcmp() for the full 'struct cpu_signature' is wrong... and that's how one of
the aforementioned 'if' sections might have been triggered - leading to a
deadlock.
Obviously, in my tests I simulated loading/resuming with the ucode of the same
version (just to see that the file is loaded/re-loaded upon resuming) so this
issue has never popped up.
I'd appreciate if someone with an appropriate system might give a try to the
2nd patch (titled "fix a comparison && deadlock...").
In any case, the deadlock situation is a must-have fix.
Reported-by: Andreas Mohr <andi@lisas.de>
Signed-off-by: Dmitry Adamushko <dmitry.adamushko@gmail.com>
Tested-by: Andreas Mohr <andi@lisas.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Cc: <stable@kernel.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Julia Lawall [Fri, 19 Dec 2008 22:50:22 +0000 (16:50 -0600)] 
fs/9p: change simple_strtol to simple_strtoul
Since v9ses->uid is unsigned, it would seem better to use simple_strtoul that
simple_strtol.
A simplified version of the semantic patch that makes this change is as
follows: (http://www.emn.fr/x-info/coccinelle/)
// <smpl>
@r2@
long e;
position p;
@@
e = simple_strtol@p(...)
@@
position p != r2.p;
type T;
T e;
@@
e =
- simple_strtol@p
+ simple_strtoul
(...)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Acked-by: Eric Van Hensbergen <ericvh@gmail.com>
Wu Fengguang [Fri, 19 Dec 2008 22:47:40 +0000 (16:47 -0600)] 
9p: convert d_iname references to d_name.name
d_iname is rubbish for long file names.
Use d_name.name in printks instead.
Signed-off-by: Wu Fengguang <wfg@linux.intel.com>
Acked-by: Eric Van Hensbergen <ericvh@gmail.com>
Duane Griffin [Fri, 19 Dec 2008 22:45:21 +0000 (16:45 -0600)] 
9p: Remove potentially bad parameter from function entry debug print.
Signed-off-by: Duane Griffin <duaneg@dghda.com>
Signed-off-by: Eric Van Hensbergen <ericvh@gmail.com>
Linus Torvalds [Fri, 19 Dec 2008 19:37:23 +0000 (11:37 -0800)]
Merge git://git./linux/kernel/git/jejb/scsi-rc-fixes-2.6
* git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-rc-fixes-2.6:
[SCSI] mpt fusion: clear list of outstanding commands on host reset
[SCSI] scsi_lib: only call scsi_unprep_request() under queue lock
[SCSI] ibmvstgt: move crq_queue_create to the end of initialization
[SCSI] libiscsi REGRESSION: fix passthrough support with older iscsi tools
[SCSI] aacraid: disable Dell Percraid quirk on Adaptec 2200S and 2120S
Linus Torvalds [Fri, 19 Dec 2008 19:37:07 +0000 (11:37 -0800)]
Merge branch 'for-linus' of git://git./linux/kernel/git/tiwai/sound-2.6
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6:
ALSA: Fix a Oops bug in omap soc driver.
ALSA: hda - Remove non-working headphone control for Dell laptops
ALSA: hda - Add no-jd model for IDT 92HD73xx
ALSA: Revert "ALSA: hda: removed unneeded hp_nid references"
ALSA: hda - Add quirk for Dell Studio 17
ALSA: hda - Fix silent HP output on D975
Linus Torvalds [Fri, 19 Dec 2008 19:36:49 +0000 (11:36 -0800)]
Merge branch 'for-linus' of git://git.kernel.dk/linux-2.6-block
* 'for-linus' of git://git.kernel.dk/linux-2.6-block:
cciss: fix problem that deleting multiple logical drives could cause a panic
Linus Torvalds [Fri, 19 Dec 2008 19:36:04 +0000 (11:36 -0800)]
Merge branch 'drm-fixes' of git://git./linux/kernel/git/airlied/drm-2.6
* 'drm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6:
drm/i915: GEM on PAE has problems - disable it for now.
drm/i915: Don't return busy for buffers left on the flushing list.
Linus Torvalds [Fri, 19 Dec 2008 19:34:36 +0000 (11:34 -0800)]
Merge branch 'for-linus' of git://neil.brown.name/md
* 'for-linus' of git://neil.brown.name/md:
md: Don't read past end of bitmap when reading bitmap.
Linus Torvalds [Fri, 19 Dec 2008 19:33:10 +0000 (11:33 -0800)]
Merge branch 'for-linus' of git://git./linux/kernel/git/jbarnes/pci-2.6
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6:
PCI hotplug: ibmphp: Fix module ref count underflow
PCI hotplug: acpiphp wants a 64-bit _SUN
PCI: pciehp: fix unexpected power off with pciehp_force
PCI: fix aer resume sanity check
Takashi Iwai [Fri, 19 Dec 2008 14:37:12 +0000 (15:37 +0100)] 
Merge branch 'fix/asoc' into for-linus
Stanley Miao [Fri, 19 Dec 2008 14:08:22 +0000 (22:08 +0800)] 
ALSA: Fix a Oops bug in omap soc driver.
There will be a Oops or frequent underrun messages when playing music with
omap soc driver, this is because a data region is incorretly sized, other data
region will be overwriten when writing to this data region.
Signed-off-by: Stanley Miao <stanley.miao@windriver.com>
Acked-by: Jarkko Nikula <jarkko.nikula@nokia.com>
Cc: stable@kernel.org
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Takashi Iwai [Fri, 19 Dec 2008 13:02:32 +0000 (14:02 +0100)]
ALSA: hda - Remove non-working headphone control for Dell laptops
The previous commit re-enabled hp_nid setup for IDT92HD73*, but
it's unneeded indeed for Dell laptops that have multiple headphones.
Setting the extra hp_nid results in a non-working "Headpohne" mixer
control. Thus hp_nid should be 0 for these dell models.
Also, the automatic addition of hp_nid should check whether it's
a dual-HP model or not. For dual-HPs, the pins are already checked
by the early workaround.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Takashi Iwai [Wed, 17 Dec 2008 13:51:01 +0000 (14:51 +0100)]
ALSA: hda - Add no-jd model for IDT 92HD73xx
Added the model without the jack-detection for some desktops that
have really no jack-detection. The recent driver caused regressions
regarding the sound output on such machines.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Takashi Iwai [Fri, 19 Dec 2008 07:20:38 +0000 (08:20 +0100)]
ALSA: Revert "ALSA: hda: removed unneeded hp_nid references"
This reverts commit
07f455f779acfb3eba4921fd1399761559b10fa9.
ALSA: hda: removed unneeded hp_nid references
Removed unneeded hp_nid references for 92hd73xx codec family.
This caused the silent output on some Intel desktops due to missing
routing of widget 0x0a and 0x0d.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Stephen M. Cameron [Thu, 18 Dec 2008 13:55:11 +0000 (14:55 +0100)] 
cciss: fix problem that deleting multiple logical drives could cause a panic
Fix problem that deleting multiple logical drives could cause a panic.
It fixes a panic which can be easily reproduced in the following way: Just
create several "arrays," each with multiple logical drives via hpacucli,
then delete the first array, and it will blow up in deregister_disk(), in
the call to get_host() when it tries to dig the hba pointer out of a NULL
queue pointer.
The problem has been present since my code to make rebuild_lun_table
behave better went in.
Signed-off-by: Stephen M. Cameron <scameron@beardog.cca.cpqcorp.net>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Joerg Schirottke [Fri, 19 Dec 2008 07:13:49 +0000 (08:13 +0100)] 
ALSA: hda - Add quirk for Dell Studio 17
Added the matching model=dell-m6 for Dell Studio 17 laptop.
Signed-off-by: Joerg Schirottke <master@kanotix.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Dave Airlie [Fri, 19 Dec 2008 05:38:34 +0000 (15:38 +1000)] 
drm/i915: GEM on PAE has problems - disable it for now.
On PAE systems, GEM allocates pages using shmem, and passes these
pages to be bound into AGP, however the AGP interfaces + the x86
set_memory interfaces all take unsigned long not dma_addr_t.
The initial fix for this was a mess, so we need to do this correctly
for 2.6.29.
Signed-off-by: Dave Airlie <airlied@redhat.com>
Eric Anholt [Mon, 15 Dec 2008 03:05:04 +0000 (19:05 -0800)] 
drm/i915: Don't return busy for buffers left on the flushing list.
These buffers don't have active rendering still occurring to them, they just
need either a flush to be emitted or a retire_requests to occur so that we
notice they're done. Return unbusy so that one of the two occurs. The two
expected consumers of this interface (OpenGL and libdrm_intel BO cache) both
want this behavior.
Signed-off-by: Eric Anholt <eric@anholt.net>
Acked-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
NeilBrown [Fri, 19 Dec 2008 05:25:01 +0000 (16:25 +1100)] 
md: Don't read past end of bitmap when reading bitmap.
When we read the write-intent-bitmap off the device, we currently
read a whole number of pages.
When PAGE_SIZE is 4K, this works due to the alignment we enforce
on the superblock and bitmap.
When PAGE_SIZE is 64K, this case read past the end-of-device
which causes an error.
When we write the superblock, we ensure to clip the last page
to just be the required size. Copy that code into the read path
to just read the required number of sectors.
Signed-off-by: Neil Brown <neilb@suse.de>
Cc: stable@kernel.org
Linus Torvalds [Fri, 19 Dec 2008 01:20:13 +0000 (17:20 -0800)]
Linux 2.6.28-rc9
Linus Torvalds [Thu, 18 Dec 2008 20:05:53 +0000 (12:05 -0800)]
Merge branch 'fixes' of git://git./linux/kernel/git/djbw/async_tx
* 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/djbw/async_tx:
async_xor: dma_map destination DMA_BIDIRECTIONAL
dmaengine: protect 'id' from concurrent registrations
ioat: wait for self-test completion
Linus Torvalds [Thu, 18 Dec 2008 20:01:02 +0000 (12:01 -0800)]
Merge branch 'fixes' of git://git./linux/kernel/git/hskinnemoen/avr32-2.6
* 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/hskinnemoen/avr32-2.6:
avr32: favr-32 build fix
ATSTK1006: Fix boot from NAND flash
avr32: remove .note.gnu.build-id section when making vmlinux.bin
avr32: Enable pullup on USART TX lines
Linus Torvalds [Thu, 18 Dec 2008 20:00:46 +0000 (12:00 -0800)]
Merge git://git./linux/kernel/git/davem/net-2.6
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6:
bnx2: Fix bug in bnx2_free_rx_mem().
irda: Add irda_skb_cb qdisc related padding
jme: Fixed a typo
net: kernel BUG at drivers/net/phy/mdio_bus.c:165!
drivers/net: starfire: Fix napi ->poll() weight handling
tlan: Fix pci memory unmapping
enc28j60: use netif_rx_ni() to deliver RX packets
tlan: Fix small (< 64 bytes) datagram transmissions
netfilter: ctnetlink: fix missing CTA_NAT_SEQ_UNSPEC
Linus Torvalds [Thu, 18 Dec 2008 20:00:01 +0000 (12:00 -0800)]
Merge git://git./linux/kernel/git/davem/sparc-2.6
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc-2.6:
sparc: We need to implement arch_ptrace_stop().
John McCutchan [Thu, 18 Dec 2008 01:43:02 +0000 (17:43 -0800)] 
Maintainer email fixes for inotify
Update John McCutchan and Robert Love's email addresses for
maintenance of inotify
Signed-off-by: John McCutchan <john@johnmccutchan.com>
Acked-by: Robert Love <rlove@rlove.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Haavard Skinnemoen [Thu, 18 Dec 2008 15:20:47 +0000 (16:20 +0100)] 
avr32: favr-32 build fix
The favr-32 board code still refers to the old asm/arch header files
which were moved to mach/ some time ago.
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
Haavard Skinnemoen [Thu, 18 Dec 2008 15:13:24 +0000 (16:13 +0100)]
ATSTK1006: Fix boot from NAND flash
Enable JFFS2 write buffer support so that the kernel can access a root
filesystem in NAND flash.
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
Ingo Molnar [Thu, 18 Dec 2008 12:28:11 +0000 (13:28 +0100)] 
Merge branch 'iommu-fixes-2.6.28' of git://git./linux/kernel/git/joro/linux-2.6-iommu into x86/urgent
Bjorn Helgaas [Wed, 17 Dec 2008 19:52:34 +0000 (12:52 -0700)] 
x86 gart: don't complain if no AMD GART found
Impact: remove annoying bootup printk
It's perfectly normal for no AMD GART to be present, e.g., if you have
Intel CPUs. None of the other iommu_init() functions makes noise when
it finds nothing.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Acked-by: Joerg Roedel <joerg.roedel@amd.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Takashi Iwai [Wed, 17 Dec 2008 12:48:29 +0000 (13:48 +0100)]
ALSA: hda - Fix silent HP output on D975
Some desktops seems to have no HP/mic jack detection on the front panel,
which results in the silent output in the recent driver, because the
driver mutes the output (to save power) when no plug is detected.
This patch adds a new model that disables the jack-detection.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Michael Chan [Thu, 18 Dec 2008 03:06:08 +0000 (19:06 -0800)] 
bnx2: Fix bug in bnx2_free_rx_mem().
DMA memory for the jumbo rx page rings was freed incorrectly using the
wrong local variable as the array index.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Neil Horman [Thu, 18 Dec 2008 00:07:47 +0000 (16:07 -0800)] 
PCI hotplug: ibmphp: Fix module ref count underflow
I happened to notice that the ibmphp hotplug driver does something
rather silly in its init routine. It purposely calls module_put so as
to underflow its module ref count to avoid being removed from the
kernel. This is bad practice, and wrong, since it provides a window for
subsequent module_gets to reset the refcount to zero, allowing an unload
to race in and cause all sorts of mysterious panics. If the module is
unsafe to load, simply omitting the module_exit parameter is sufficient
to prevent the kernel from allowing the unload.
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Samuel Ortiz [Wed, 17 Dec 2008 23:44:58 +0000 (15:44 -0800)] 
irda: Add irda_skb_cb qdisc related padding
We need to pad irda_skb_cb in order to keep it safe accross dev_queue_xmit()
calls. This is some ugly and temporary hack triggered by recent qisc code
changes.
Even though it fixes bugzilla.kernel.org bug #11795, it will be replaced by a
proper fix before 2.6.29 is released.
Signed-off-by: Samuel Ortiz <samuel@sortiz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Wed, 17 Dec 2008 23:05:26 +0000 (15:05 -0800)]
Merge branch 'i2c-fixes' of git://aeryn.fluff.org.uk/bjdooks/linux
* 'i2c-fixes' of git://aeryn.fluff.org.uk/bjdooks/linux:
i2c-s3c2410: fix check for being in suspend.
i2c-cpm: Detect and report NAK right away instead of timing out
Linus Torvalds [Wed, 17 Dec 2008 23:01:23 +0000 (15:01 -0800)]
Merge branch 'upstream-linus' of git://git./linux/kernel/git/mfasheh/ocfs2
* 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mfasheh/ocfs2:
ocfs2: Add JBD2 compat feature bit.
ocfs2: Always update xattr search when creating bucket.
Linus Torvalds [Wed, 17 Dec 2008 23:01:06 +0000 (15:01 -0800)]
Merge git://git./linux/kernel/git/gregkh/usb-2.6
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb-2.6:
USB: pl2303: add id for Hewlett-Packard LD220-HP POS pole display
USB: set correct configuration in probe of ti_usb_3410_5052
USB: add 5372:2303 to pl2303
USB: skip Set-Interface(0) if already in altsetting 0
USB: fix comment about endianness of descriptors
USB: Documentation/usb/gadget_serial.txt: update to match driver use_acm behaviour
usbmon: drop bogus 0t from usbmon.txt
USB: gadget: fix rndis working at high speed
USB: ftdi_sio: Adding Ewert Energy System's CANdapter PID
USB: tty: SprogII DCC controller identifiers
usb-storage: update unusual_devs entry for Nokia 5310
USB: Unusual devs patch for Nokia 3500c
USB: storage: unusual_devs.h: Nokia 3109c addition
USB: fix problem with usbtmc driver not loading properly
Linus Torvalds [Wed, 17 Dec 2008 23:00:54 +0000 (15:00 -0800)]
Merge git://git./linux/kernel/git/gregkh/driver-core-2.6
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core-2.6:
STAGING: Move staging drivers back to staging-specific menu
driver core: add newlines to debugging enabled/disabled messages
xilinx_hwicap: remove improper wording in license statement
driver core: fix using 'ret' variable in unregister_dynamic_debug_module
Jeff Layton [Wed, 17 Dec 2008 11:31:53 +0000 (06:31 -0500)] 
cifs: fix buffer overrun in parse_DFS_referrals
While testing a kernel with memory poisoning enabled, I saw some warnings
about the redzone getting clobbered when chasing DFS referrals. The
buffer allocation for the unicode converted version of the searchName is
too small and needs to take null termination into account.
Signed-off-by: Jeff Layton <jlayton@redhat.com>
Acked-by: Steve French <sfrench@us.ibm.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Wed, 17 Dec 2008 22:58:56 +0000 (14:58 -0800)]
Merge branch 'merge' of git://git./linux/kernel/git/galak/powerpc
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/galak/powerpc:
powerpc: Fix corruption error in rh_alloc_fixed()
powerpc/fsl-booke: Fix the miss interrupt restore
Dmitry Baryshkov [Thu, 27 Nov 2008 21:01:28 +0000 (00:01 +0300)] 
STAGING: Move staging drivers back to staging-specific menu
Signed-off-by: Dmitry Baryshkov <dbaryshkov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Marcel Holtmann [Sun, 30 Nov 2008 13:01:26 +0000 (14:01 +0100)] 
driver core: add newlines to debugging enabled/disabled messages
Both messages are missing the newline and thus dmesg output gets
scrambled.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Greg Kroah-Hartman [Sun, 7 Dec 2008 05:10:51 +0000 (21:10 -0800)] 
xilinx_hwicap: remove improper wording in license statement
GPLv2 doesn't allow additional restrictions to be imposed on any
code, so this wording needs to be removed from these files.
Signed-off-by: Stephen Neuendorffer <stephen.neuendorffer@xilinx.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Johann Felix Soden [Thu, 30 Oct 2008 21:44:39 +0000 (22:44 +0100)] 
driver core: fix using 'ret' variable in unregister_dynamic_debug_module
The 'ret' variable is assigned, but not used in the return statement. Fix this.
Signed-off-by: Johann Felix Soden <johfel@users.sourceforge.net>
Acked-by: Jason Baron <jbaron@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Mike Provencher [Tue, 16 Dec 2008 20:30:14 +0000 (14:30 -0600)] 
USB: pl2303: add id for Hewlett-Packard LD220-HP POS pole display
Add id for the Hewlett-Packard LD220-HP POS pole display.
Bus 002 Device 002: ID 03f0:3524 Hewlett-Packard
Signed-off-by: Mike Provencher <mike.provencher@hp.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Oliver Neukum [Tue, 16 Dec 2008 11:25:55 +0000 (12:25 +0100)] 
USB: set correct configuration in probe of ti_usb_3410_5052
This driver transfers firmware. It may just as well set the correct
configuration.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Matthew Arnold [Sat, 13 Dec 2008 11:42:53 +0000 (22:42 +1100)] 
USB: add 5372:2303 to pl2303
This patch adds the "Superial" USB-Serial converter to pl2303 so that it
is detected, by the correct driver. Adds the relevant vendor:product
(5372:2303) to the device tables in pl2303.c & pl2303.h. The patch has
been tested against 2.6.24-22-generic.
Signed-off-by: Matthew D Arnold <matthew.arnold-1@uts.edu.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Alan Stern [Mon, 1 Dec 2008 15:24:41 +0000 (10:24 -0500)] 
USB: skip Set-Interface(0) if already in altsetting 0
When a driver unbinds from an interface, usbcore always sends a
Set-Interface request to reinstall altsetting 0. Unforunately, quite
a few devices have buggy firmware that crashes when it receives this
request.
To avoid such problems, this patch (as1180) arranges to send the
Set-Interface request only when the interface is not already in
altsetting 0.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Phil Endecott [Mon, 1 Dec 2008 15:22:33 +0000 (10:22 -0500)] 
USB: fix comment about endianness of descriptors
This patch fixes a comment and clarifies the documentation about the
endianness of descriptors. The current policy is that descriptors will
be little-endian at the API even on big-endian systems; however the
/proc/bus/usb API predates this policy and presents descriptors with
some multibyte fields byte-swapped.
Signed-off-by: Phil Endecott <usb_endian_patch@chezphil.org>
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Peter Korsgaard [Thu, 4 Dec 2008 15:30:53 +0000 (16:30 +0100)] 
USB: Documentation/usb/gadget_serial.txt: update to match driver use_acm behaviour
Commit
7bb5ea54 (usb gadget serial: use composite gadget framework)
changed the default for the use_acm parameter from 0 to 1.
Update the documentation to match.
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Pete Zaitcev [Thu, 4 Dec 2008 23:17:00 +0000 (16:17 -0700)] 
usbmon: drop bogus 0t from usbmon.txt
The example is incorrect: there is no 0t socket (the '1t' format has no
bus number in it). Also, correct the broken sentence for USB Tag.
Signed-off-by: Pete Zaitcev <zaitcev@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
David Brownell [Tue, 25 Nov 2008 07:11:03 +0000 (23:11 -0800)] 
USB: gadget: fix rndis working at high speed
Fix a bug specific to highspeed mode in the recently updated RNDIS
support: it wasn't setting up the high speed notification endpoint,
which prevented high speed RNDIS links from working.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Tested-by: Anand Gadiyar <gadiyar@ti.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Andrew Ewert [Thu, 4 Dec 2008 15:09:59 +0000 (09:09 -0600)] 
USB: ftdi_sio: Adding Ewert Energy System's CANdapter PID
The following patch adds in the USB PID for Ewert Energy System's CANdapter
device (CANBUS to USB-Serial which uses the FTDI 245R chipset) to the ftdi_sio
device driver.
The patch was tested successfully on Linux kernel 2.6.27 under Ubuntu.
Relevant output from /proc/bus/usb/devices (With patch installed):
T: Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 2 Spd=12 MxCh= 0
D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS= 8 #Cfgs= 1
P: Vendor=0403 ProdID=9f80 Rev= 6.00
S: Manufacturer=Ewert Energy Systems
S: Product=CANdapter
S: SerialNumber=A6RGB3Z3
C:* #Ifs= 1 Cfg#= 1 Atr=a0 MxPwr= 90mA
I:* If#= 0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=ftdi_sio
E: Ad=81(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms
E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms
Signed-off-by: Andrew Ewert <andrew@ewertenergy.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Alan Cox [Sun, 7 Dec 2008 07:46:04 +0000 (23:46 -0800)] 
USB: tty: SprogII DCC controller identifiers
Someone on rmweb reminded me this had been overlooked from ages ago..
Add the identifiers for the Sprog II USB. This is a DCC control interface
using the FTDI-SIO hardware: http://www.sprog-dcc.co.uk/. People have been
using it with insmod options for ages, this just puts it into the driver
data.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Alan Stern [Mon, 1 Dec 2008 15:23:43 +0000 (10:23 -0500)]
usb-storage: update unusual_devs entry for Nokia 5310
This patch (as1179) updates the unusual_devs entry for Nokia's 5310
phone to include a more recent firmware revision.
This fixes Bugzilla #12099.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Tested-by: Robson Roberto Souza Peixoto <robsonpeixoto@gmail.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Ozan Sener [Mon, 8 Dec 2008 17:15:45 +0000 (19:15 +0200)] 
USB: Unusual devs patch for Nokia 3500c
T: Bus=02 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 3 Spd=12 MxCh= 0
D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1
P: Vendor=0421 ProdID=0060 Rev= 5.51
S: Manufacturer=Nokia
S: Product=Nokia 3500c
S: SerialNumber=
357687010280751
C:* #Ifs= 1 Cfg#= 1 Atr=c0 MxPwr=100mA
I:* If#= 0 Alt= 0 #EPs= 2 Cls=08(stor.) Sub=06 Prot=50 Driver=usb-storage
E: Ad=81(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms
E: Ad=01(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms
From: Ozan Sener <themgzzy@gmail.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
CSÉCSY László [Tue, 9 Dec 2008 22:39:14 +0000 (23:39 +0100)] 
USB: storage: unusual_devs.h: Nokia 3109c addition
2.6.26(.x, cannot remember) could handle the microSD card in my Nokia
3109c attached via USB as mass storage, 2.6.27(.x, up to and included
2.6.27.8) cannot. Please find the attached patch which fixes this
regression, and a copy of /proc/bus/usb/devices with my phone plugged in
running with this patch on Frugalware.
T: Bus=02 Lev=01 Prnt=01 Port=01 Cnt=02 Dev#= 4 Spd=12 MxCh= 0
D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1
P: Vendor=0421 ProdID=0063 Rev= 6.01
S: Manufacturer=Nokia
S: Product=Nokia 3109c
S: SerialNumber=
359561013742570
C:* #Ifs= 1 Cfg#= 1 Atr=c0 MxPwr=100mA
I:* If#= 0 Alt= 0 #EPs= 2 Cls=08(stor.) Sub=06 Prot=50 Driver=usb-storage
E: Ad=81(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms
E: Ad=01(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms
From: CSÉCSY László <boobaa@frugalware.org>
Cc: Phil Dibowitz <phil@ipom.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Greg Kroah-Hartman [Thu, 4 Dec 2008 00:33:09 +0000 (16:33 -0800)]
USB: fix problem with usbtmc driver not loading properly
The usbtmc driver forgot to export its device table to userspace.
Without this, it is never loaded properly when such a device is seen by
the system.
Cc: Marcel Janssen <marcel.janssen@admesy.nl>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Guillaume Knispel [Tue, 9 Dec 2008 14:28:34 +0000 (15:28 +0100)] 
powerpc: Fix corruption error in rh_alloc_fixed()
There is an error in rh_alloc_fixed() of the Remote Heap code:
If there is at least one free block blk won't be NULL at the end of the
search loop, so -ENOMEM won't be returned and the else branch of
"if (bs == s || be == e)" will be taken, corrupting the management
structures.
Signed-off-by: Guillaume Knispel <gknispel@proformatique.com>
Acked-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Dave Liu [Wed, 17 Dec 2008 10:24:15 +0000 (18:24 +0800)] 
powerpc/fsl-booke: Fix the miss interrupt restore
The commit
e5e774d8833de1a0037be2384efccadf16935675
powerpc/fsl-booke: Fix problem with _tlbil_va being interrupted
introduce one issue. that casue the problem like this:
Kernel BUG at
c00b19fc [verbose debug info unavailable]
Oops: Exception in kernel mode, sig: 5 [#1]
MPC8572 DS
Modules linked in:
NIP:
c00b19fc LR:
c00b1c34 CTR:
c0064e88
REGS:
ef02b7b0 TRAP: 0700 Not tainted (
2.6.28-rc8-00057-g1bda712)
MSR:
00021000 <ME> CR:
44048028 XER:
20000000
TASK =
ef02c000[1] 'init' THREAD:
ef02a000
GPR00:
00000001 ef02b860 ef02c000 eec201a0 c0dec2c0 00000000 000078a1 00000400
GPR08:
c00b4e40 000078a1 c048ec00 a1780000 44048028 ecd26917 00000001 ef02b948
GPR16:
ffffffea 0000020c 00000000 00000000 00000003 0000000a 00000000 000078a1
GPR24:
eec201a0 00000000 ed849000 00000400 ef02b95c 00000001 ef02b978 ef02b984
NIP [
c00b19fc] __find_get_block+0x24/0x238
LR [
c00b1c34] __getblk+0x24/0x2a0
Call Trace:
[
ef02b860] [
c017b768] generic_make_request+0x290/0x328 (unreliable)
[
ef02b8b0] [
c00b1c34] __getblk+0x24/0x2a0
[
ef02b910] [
c00b4ae4] __bread+0x14/0xf8
[
ef02b920] [
c00fc228] ext2_get_branch+0xf0/0x138
[
ef02b940] [
c00fcc88] ext2_get_block+0xb8/0x828
[
ef02ba00] [
c00bbdc8] do_mpage_readpage+0x188/0x808
[
ef02bac0] [
c00bc5b4] mpage_readpages+0xec/0x144
[
ef02bb50] [
c00fba38] ext2_readpages+0x24/0x34
[
ef02bb60] [
c006ade0] __do_page_cache_readahead+0x150/0x230
[
ef02bbb0] [
c0064bdc] filemap_fault+0x31c/0x3e0
[
ef02bbf0] [
c00728b8] __do_fault+0x60/0x5b0
[
ef02bc50] [
c0011e0c] do_page_fault+0x2d8/0x4c4
[
ef02bd10] [
c000ed90] handle_page_fault+0xc/0x80
[
ef02bdd0] [
c00c7adc] set_brk+0x74/0x9c
[
ef02bdf0] [
c00c9274] load_elf_binary+0x70c/0x1180
[
ef02be70] [
c00945f0] search_binary_handler+0xa8/0x274
[
ef02bea0] [
c0095818] do_execve+0x19c/0x1d4
[
ef02bed0] [
c000766c] sys_execve+0x58/0x84
[
ef02bef0] [
c000e950] ret_from_syscall+0x0/0x3c
[
ef02bfb0] [
c009c6fc] sys_dup+0x24/0x6c
[
ef02bfc0] [
c0001e04] init_post+0xb0/0xf0
[
ef02bfd0] [
c046c1ac] kernel_init+0xcc/0xf4
[
ef02bff0] [
c000e6d0] kernel_thread+0x4c/0x68
Instruction dump:
4bffffa4 813f000c 4bffffac 9421ffb0 7c0802a6 7d800026 90010054 bf210034
91810030 7c0000a6 68008000 54008ffe <
0f000000>
3d20c04e 3b29ffb8 38000008
The issue was the beqlr returns early but we haven't reenabled interrupts.
Signed-off-by: Dave Liu <daveliu@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
projects / linux-2.6 / log
