ixgbe: ethtool support to change advertised link modes of 82599 adapters

Add ethtool support to change advertised link modes/autoneg settings of
82599 multispeed fiber adapters.

Signed-off-by: Mallikarjuna R Chilakala <mallikarjuna.chilakala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

ixgbe: Fix 82599 adapter link flickering issues

Fix autoneg restart issues in flow control path which might create
endless link flickering due to known timing issues with 82599
adapters.

Signed-off-by: Mallikarjuna R Chilakala <mallikarjuna.chilakakla@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

ixgbe: Harden the 82599 multispeed fiber autotry mechanism

82599 supports multispeed fiber optical modules (10Gbps/1Gbps).  Some
scenarios can cause the autotry mechanism to not negotiate link properly.
What needs to happen is the driver must flap the Tx laser to induce an Rx
Loss of Signal on the link partner.  This will restart the autotry
mechanism to get link into a known state.  The software definable pin (SDP)
3 on the 0x10fb NIC is wired to cause a Tx LOS event, which triggers the
Rx LOS we require.

Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Acked-by: Mallikarjuna R Chilakala <mallikarjuna.chilakala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

ixgbe: Add ethtool offline test support

This patch adds support for the ethtool internal test engine.

Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

ixgbe: Change the 82599 PHY DSP restart logic

When reprogramming the 82599 analog PHY to either SFI optical or Direct
Attach Twinax, we need to restart the DSP in the PHY.  The current method
can cause contention with our FW which is managing PHY state, and will
cause unexpected link flaps.  This patch fixes the DSP restart by issuing
an AN_RESTART in the MAC, which will properly propagate the DSP restart to
the PHY.  This ensures we don't collide with the FW.

Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

ixgbe: Enable ACPI WoL capabilities for 82599

The 82599 KX4 device defaults to legacy power management, or APME.  This
puts the device into ACPI mode, which allows more robust WoL setups to
work properly.

Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

cfg80211: errno.h: define ERFKILL

Commit 1f87f7d3 (cfg80211: add rfkill support) added ERFKILL
to asm-generic/errno.h, but alpha, mips, parisc and sparc use
their own numbering scheme and do not include asm-generic/errno.h.
We need to add definition of ERFKILL for them.

Signed-off-by: Alexander Beregalov <a.beregalov@gmail.com>
Acked-by: Ralf Baechle <ralf@linux-mips.org>
Acked-by: Kyle McMartin <kyle@mcmartin.ca>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge branch 'master' of git://git./linux/kernel/git/linville/wireless-next-2.6

removal of forcedeth device ids

This patch removes the forcedeth device ids from pci_ids.h

The forcedeth driver uses the device id constants directly in its source
file.

[ Need to keep PCI_DEVICE_ID_NVIDIA_NVENET_15 in order to keep
  drivers/pci/quirks.c building -DaveM ]

Signed-off-by: Ayaz Abdulla <aabdulla@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

forcedeth: addition of new mcp89 device id

This patch adds a new device id for mcp89 chipset.

Signed-off-by: Ayaz Abdulla <aabdulla@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

forcedeth: remove device id macros

This patch removes the device id macros and instead uses the constants
directly.

The areas in which logic expressions where using the macros now instead
use feature/workaround flags.

No new functionality has been introduced in this patch, only clean up of
flags and macros.

Signed-off-by: Ayaz Abdulla <aabdulla@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

wimax: depend on rfkill properly

My mistake, I should have added that when cleaning up
rfkill and changing wimax.

Reported-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Acked-by: Inaky Perez-Gonzalez <inaky@linux.intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ar9170: remove deprecated code

This patch removes code (deprecated by "cfg80211: add rfkill support" )

main.c: In function 'ar9170_op_config':
main.c:1306: warning: '__IEEE80211_CONF_CHANGE_RADIO_ENABLED'
is deprecated (declared at include/net/mac80211.h:551)

and a useless device state.

Signed-off-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

iwlwifi: fix comment describing disable_11n

Fixing a comment in the code describing this module parameter.
The description printed when user runs "modinfo" is correct.

Reported-by: Jiajia Zheng <jiajia.zheng@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

iwlwifi: add value and range define for link quality command

Instead of hardcoding the link quality parameters inside the functions,
adding #define in iwl-commands.h to shared by different functions.
Also include the valid range for number of link quality parameters.

Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

iwlagn: delay ict interrupt.

Wait until ucode is loaded and driver receive ALIVE_REPLY then switch
 to ICT interrupt. This ensures we receive all interrupts indicating
 successful ucode load.

Signed-off-by: Mohamed Abbas <mohamed.abbas@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

iwl3945/iwlwifi: fix led bug when SW rfkill

Patch fixes the bug at
http://www.intellinuxwireless.org/bugzilla/show_bug.cgi?id=1903

when SW rfkill is invoked by 'iwconfig txpower off',
the existing connection disassociates and led off command is sent
to the device which returns error as rfkill is 'true'.

Patch fixes this by just avoiding sending the led off/on command when
disassociated. The main purpose of the led_disassociate callback
is to start or stop the blinking.
There are three states in led
1) Always on when radio is on
2) Always off when radio is off
3) blink when associated and if there is some traffic.

In this callback 'allow_blinking' needs to be set false
when associated, as LED will be always on.

Signed-off-by: Abhijeet Kolekar <abhijeet.kolekar@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

iwl3945: port allow skb allocation in tasklet patch

Port "iwlcore: Allow skb allocation from tasklet." to 3945

If RX queue becomes empty then we need to restock the queue from
tasklet to prevent ucode from starving. A caller to iwl_rx_allocate
will decide if allocated buffer should come from GFP_ATOMIC or
GFP_KERNEL.

Signed-off-by: Abhijeet Kolekar <abhijeet.kolekar@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

iwlwifi: unify station management

This patch unifies 3945 and AGN station management
It also removes useless struct iwl_station_mgmt ops
and cleanups a bit the interface

Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Tested-by: Abhijeet Kolekar <abhijeet.kolekar@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

TI DaVinci EMAC: Remove print_mac, DECLARE_MAC_BUF

Use printk format specifier for MAC address.
Remove DECALRE_MAC_BUF and print_mac() usage in the driver.

Signed-off-by: Chaithrika U S <chaithrika@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

tun: Only wake up writers

When I added socket accounting to tun I inadvertently introduced
spurious wake-up events that kills qemu performance.  The problem
occurs when qemu polls on the tun fd for read, and then transmits
packets.  For each packet transmitted, we will wake up qemu even
if it only cares about read events.

Now this affects all sockets, but it is only a new problem for
tun.  So this patch tries to fix it for tun first and we can then
look at the problem in general.

Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge branch 'net-next' of git://git./linux/kernel/git/vxy/lksctp-dev

ipv4: remove ip_mc_drop_socket() declaration from af_inet.c.

ip_mc_drop_socket() method is declared in linux/igmp.h, which
is included anyhow in af_inet.c. So there is no need for this declaration.
This patch removes it from af_inet.c.

Signed-off-by: Rami Rosen <ramirose@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

gso: Stop fraglists from escaping

As it stands skb fraglists can get past the check in dev_queue_xmit
if the skb is marked as GSO.  In particular, if the packet doesn't
have the proper checksums for GSO, but can otherwise be handled by
the underlying device, we will not perform the fraglist check on it
at all.

If the underlying device cannot handle fraglists, then this will
break.

The fix is as simple as moving the fraglist check from the device
check into skb_gso_ok.

This has caused crashes with Xen when used together with GRO which
can generate GSO packets with fraglists.

Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>

cxgb3: minor aq100x phy fixes

Use generic MDIO generic values.
Based on Ben Hutchings'review comments.

Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

cxgb3: Update FW to 7.4.0

Update FW to 7.4.
Bump up driver revision.

Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

cfg80211: fix Kconfig for users of cfg80211

 * iwm doesn't depend on cfg80211 or wireless extensions
 * rndis wlan selects cfg80211 - needs to depend
 * mac80211 selects cfg80211 - needs to depend

Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Acked-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rfkill: document /dev/rfkill

Add some blurb about /dev/rfkill to the documentation and
fix the "transmiter" spelling error.

Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rfkill: always init poll delayed work

The rfkill core didn't initialise the poll delayed work
because it assumed that polling was always done by specifying
the poll function. cfg80211, however, would like to start
polling only later, which is a valid use case and easy to
support, so change rfkill to always initialise the poll
delayed work and thus allow starting polling by calling the
rfkill_resume_polling() function after registration.

Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath5k: disable beacon interrupt when interface is down

When we remove the active interface, there's no need to continue
sending beacons; doing so would cause a null pointer deref in
ieee80211_beacon_get().  Disable the interrupt in remove_interface
and add a WARN_ON(!vif) in case there are other instances lurking.

Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mac80211: removed unused variable in ieee80211_tx()

Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mac80211: extend sta kdoc - explain when they are added

Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

cfg80211: make ieee80211_get_mesh_hdrlen() static

Fixes spares warning:
net/wireless/util.c:261:5: warning:
symbol 'ieee80211_get_mesh_hdrlen' was not declared. Should it be static?

Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath: make regulatory parsing more verbose on debug

This should help when reviewing issues regarding regulatory
domain on ath5k/ath9k/ar9170.

Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: Fix write callback of 'debug' which configures debug mask

Handle error condition on copy_from_user() properly and
make sure a NUL terminated char[] is sent to strict_strtoul()
for proper conversion.

Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

iwm: port to new cfg80211 rfkill

Which means removing all rfkill code since it only does
soft-kill which cfg80211 will now handle in exactly the
same way the driver did.

Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

cfg80211: add rfkill support

To be easier on drivers and users, have cfg80211 register an
rfkill structure that drivers can access. When soft-killed,
simply take down all interfaces; when hard-killed the driver
needs to notify us and we will take down the interfaces
after the fact. While rfkilled, interfaces cannot be set UP.

Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rfkill: add function to query state

Sometimes it is necessary to know how the state is,
and it is easier to query rfkill than keep track of
it somewhere else, so add a function for that. This
could later be expanded to return hard/soft block,
but so far that isn't necessary.

Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

cfg80211: move txpower wext from mac80211

This patch introduces new cfg80211 API to set the TX power
via cfg80211, puts the wext code into cfg80211 and updates
mac80211 to use all that. The -ENETDOWN bits are a hack but
will go away soon.

Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rfkill: create useful userspace interface

The new code added by this patch will make rfkill create
a misc character device /dev/rfkill that userspace can use
to control rfkill soft blocks and get status of devices as
well as events when the status changes.

Using it is very simple -- when you open it you can read
a number of times to get the initial state, and every
further read blocks (you can poll) on getting the next
event from the kernel. The same structure you read is
also used when writing to it to change the soft block of
a given device, all devices of a given type, or all
devices.

This also makes CONFIG_RFKILL_INPUT selectable again in
order to be able to test without it present since its
functionality can now be replaced by userspace entirely
and distros and users may not want the input part of
rfkill interfering with their userspace code. We will
also write a userspace daemon to handle all that and
consequently add the input code to the feature removal
schedule.

In order to have rfkilld support both kernels with and
without CONFIG_RFKILL_INPUT (or new kernels after its
eventual removal) we also add an ioctl (that only exists
if rfkill-input is present) to disable rfkill-input.
It is not very efficient, but at least gives the correct
behaviour in all cases.

Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rfkill: rewrite

This patch completely rewrites the rfkill core to address
the following deficiencies:

 * all rfkill drivers need to implement polling where necessary
   rather than having one central implementation

 * updating the rfkill state cannot be done from arbitrary
   contexts, forcing drivers to use schedule_work and requiring
   lots of code

 * rfkill drivers need to keep track of soft/hard blocked
   internally -- the core should do this

 * the rfkill API has many unexpected quirks, for example being
   asymmetric wrt. alloc/free and register/unregister

 * rfkill can call back into a driver from within a function the
   driver called -- this is prone to deadlocks and generally
   should be avoided

 * rfkill-input pointlessly is a separate module

 * drivers need to #ifdef rfkill functions (unless they want to
   depend on or select RFKILL) -- rfkill should provide inlines
   that do nothing if it isn't compiled in

 * the rfkill structure is not opaque -- drivers need to initialise
   it correctly (lots of sanity checking code required) -- instead
   force drivers to pass the right variables to rfkill_alloc()

 * the documentation is hard to read because it always assumes the
   reader is completely clueless and contains way TOO MANY CAPS

 * the rfkill code needlessly uses a lot of locks and atomic
   operations in locked sections

 * fix LED trigger to actually change the LED when the radio state
   changes -- this wasn't done before

Tested-by: Alan Jenkins <alan-jenkins@tuffmail.co.uk>
Signed-off-by: Henrique de Moraes Holschuh <hmh@hmh.eng.br> [thinkpad]
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

nl80211: use GFP_ATOMIC for michael mic failure message

nl80211_michael_mic_failure can be called in atomic context but
does a GFP_KERNEL allocation.  Fixes the error below:

[  126.793225] BUG: sleeping function called from invalid context at mm/slab.c:3055
[  126.793234] in_atomic(): 1, irqs_disabled(): 0, pid: 0, name: swapper
[  126.793241] 2 locks held by swapper/0:
[  126.793246]  #0:  (&sc->rxbuflock){+.-.+.}, at: [<f94e1b46>] ath5k_tasklet_rx+0x34/0x55e [ath5k]
[  126.793294]  #1:  (rcu_read_lock){.+.+.+}, at: [<f92872f3>] __ieee80211_rx+0x7e/0x563 [mac80211]
[  126.793342] Pid: 0, comm: swapper Not tainted 2.6.30-rc7-wl #124
[  126.793347] Call Trace:
[  126.793361]  [<c014499d>] ? __debug_show_held_locks+0x1e/0x20
[  126.793380]  [<c011e9a3>] __might_sleep+0x100/0x107
[  126.793386]  [<c018ea99>] kmem_cache_alloc+0x35/0x170
[  126.793393]  [<c02e8bb1>] ? __alloc_skb+0x2e/0x117
[  126.793397]  [<c014517d>] ? mark_held_locks+0x43/0x5b
[  126.793402]  [<c02e8bb1>] __alloc_skb+0x2e/0x117
[  126.793419]  [<f851a836>] nl80211_michael_mic_failure+0x2a/0x1fa [cfg80211]
[  126.793425]  [<c01453b8>] ? trace_hardirqs_on_caller+0xf6/0x130
[  126.793430]  [<c01453fd>] ? trace_hardirqs_on+0xb/0xd
[  126.793444]  [<f851b2b8>] cfg80211_michael_mic_failure+0x30/0x38 [cfg80211]
[  126.793463]  [<f928bf69>] mac80211_ev_michael_mic_failure+0xfd/0x108 [mac80211]
[  126.793480]  [<f9279fbd>] ieee80211_rx_h_michael_mic_verify+0xd4/0x117 [mac80211]
[  126.793499]  [<f9285ef3>] ieee80211_invoke_rx_handlers+0xdde/0x1963 [mac80211]
[  126.793505]  [<c0107152>] ? sched_clock+0x3f/0x64
[  126.793511]  [<c0107152>] ? sched_clock+0x3f/0x64
[  126.793516]  [<c01445d7>] ? trace_hardirqs_off+0xb/0xd
[  126.793521]  [<c0107152>] ? sched_clock+0x3f/0x64
[  126.793526]  [<c0146454>] ? __lock_acquire+0x62c/0x1271
[  126.793545]  [<f9286fbb>] __ieee80211_rx_handle_packet+0x543/0x564 [mac80211]
[  126.793564]  [<f9287757>] __ieee80211_rx+0x4e2/0x563 [mac80211]
[  126.793577]  [<f94e1ff6>] ath5k_tasklet_rx+0x4e4/0x55e [ath5k]
[  126.793583]  [<c0102b54>] ? restore_nocheck_notrace+0x0/0xe
[  126.793589]  [<c0129aa2>] tasklet_action+0x92/0xe5
[  126.793594]  [<c0129f22>] __do_softirq+0xb1/0x182
[  126.793599]  [<c012a023>] do_softirq+0x30/0x48
[  126.793603]  [<c012a19b>] irq_exit+0x3d/0x74
[  126.793609]  [<c0358016>] do_IRQ+0x76/0x8c
[  126.793613]  [<c010312e>] common_interrupt+0x2e/0x34
[  126.793618]  [<c014007b>] ? timer_list_show+0x277/0x939
[  126.793630]  [<f88eb321>] ? acpi_idle_enter_bm+0x266/0x291 [processor]
[  126.793636]  [<c02d00f6>] cpuidle_idle_call+0x6a/0x9c
[  126.793640]  [<c0101cc8>] cpu_idle+0x53/0x87
[  126.793645]  [<c0344510>] rest_init+0x6c/0x6e
[  126.793651]  [<c04dd74d>] start_kernel+0x286/0x28b
[  126.793656]  [<c04dd037>] __init_begin+0x37/0x3c

Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

libertas: improve function init/shutdown handling for SD8688

This patch is to incorporate Dan Williams' comments for commit:
"libertas: implement function init/shutdown commands for SD8688"

1. remove fn_init_required and fn_shutdown_required variables from
lbs_private structure. If required, __lbs_cmd() will be called
directly to send function init/shutdown command for SD8688 in
if_sdio_probe() or if_sdio_remove() callback.

2. add global variable "user_rmmod" to distinguish between the module
removal case and the card removal case. This flag will be checked in
if_sdio_remove() against SD8688 card to determine whether or not the
function shutdown command needs to be sent.

3. remove "card" from if_sdio_model structure as it cannot store
card pointers for multiple cards. Besides, it's no longer needed
to store the "card" pointer with changes #1 & #2 above.

Signed-off-by: Bing Zhao <bzhao@marvell.com>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

wireless/p54: prepare for FIRMWARE_NAME_MAX removal

We're going to remove the FIRMWARE_NAME_MAX definition in order to avoid any
firmware name length restriction.
This patch gets rid of the statically allocated p54usb firmware string, and
replaces them with const char pointers.

Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

iwmc3200wifi: shrink calibration lmac name

iwmc3200wifi: trim down calibration firmware name

The patch trims down iwmc3200wifi calibration firmware name from
iwmc3200wifi-lmac-calib-sdio.bin to iwmc3200wifi-calib-sdio.bin. We can
shorten the firmware name because all calibration is done by LMAC.

Signed-off-by: Samuel Ortiz <samuel.ortiz@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ar9170: cancel led worker properly on exit

"[PATCH 3/4 v2] ar9170: fix LED power state handling" revealed
a bug which can cause a ugly crash.

The delayed worker is canceled before the LED class functions are
unregistered... So, if something manages to update the LEDs
while unregister routine is running the timer could fire _after_ the
module has been unloaded.

Signed-off-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ar9170usb: more minor fixes

This patch contains a few more mostly random fixes for the USB front-end.

1. handle irq command response, instead of printing it to the console.

2. remove fixed FIXME.
    (real fix: "ar9170usb: reset device on resume". )

3. some more one-liner.
- get rid of a useless "return;"
- add a few branch prediction hints in hot-paths
etc.

Signed-off-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ar9170: fix lockdep warning on hibernate

This patch takes care of Johannes' deadlock report by moving the
mutex_lock right after cancel_work_sync in ar9170_op_stop.

Besides, the janitor does not need to hold the mutex anymore,
so this extra lines can be removed as well.

Signed-off-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ar9170: fix LED power state handling

This patch fixes a minor visual bug in the led code, which
left the LED in the wrong power state when it was toggled
in a _unexpected_ way (e.g: enabling the LED twice).

Signed-off-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ar9170: kill duplicated HT feature flag

This patch removes a redundant flag.

.cap = IEEE80211_HT_CAP_MAX_AMSDU | \
> IEEE80211_HT_CAP_SM_PS | \ <
[...] \
> IEEE80211_HT_CAP_SM_PS, \ <
.ampdu_factor   = 3, \

Signed-off-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ar9170: use bitop macros for tx filter flags

This patch fixes a bug in configure_filter's (sub-)routines.
We never really cleared the flags once we updated the hardware state,
so we wasted our resources by applying already active settings.

Signed-off-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ar9170: introduce functions for MAC programming

This patch introduces 3 new function which are used to update
the MAC state, whenever needed... e.g: after a band switch.

Signed-off-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ar9170: 40mhz fixes

This patch replace a few constant magics which may affected
the device when operating in a 40MHz channel.

Signed-off-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ar9170: update hardware definitions

This patch only contains a few uncritical updates for the
hardware definition header.

Signed-off-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ar9170: fix beacon plcp settings

This patch fixes a simple copy & paste error that affected beacon
transmission in 802.11a mode.

Signed-off-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mac80211_hwsim: remove deprecated radio_enabled

This removes the use of the deprecated radio_enabled setting
and code associated with that.

Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

cfg80211: fix for duplicate userspace replies

This fixes an incorrect assumption (BUG_ON) made in
cfg80211 when handling country IE regulatory requests.
The assumption was that we won't try to call_crda()
twice for the same event and therefore we will not
recieve two replies through nl80211 for the regulatory
request. As it turns out it is true we don't call_crda()
twice for the same event, however, kobject_uevent_env()
*might* send the udev event twice and/or userspace can
simply process the udev event twice. We remove the BUG_ON()
and simply ignore the duplicate request.

For details refer to this thread:

http://marc.info/?l=linux-wireless&m=124149987921337&w=2

Cc: stable@kernel.org
Reported-by: Maxim Levitsky <maximlevitsky@gmail.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

net: introduce pre-up netdev notifier

NETDEV_UP is called after the device is set UP, but sometimes
it is useful to be able to veto the device UP. Introduce a
new NETDEV_PRE_UP notifier that can be used for exactly this.
The first use case will be cfg80211 denying interfaces to be
set UP if the device is known to be rfkill'ed.

Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ar9170: add AVM FRITZ devices

This adds:

USB 0x057C:0x8401       AVM FRITZ!WLAN USB Stick N
USB 0x057C:0x8402       AVM FRITZ!WLAN USB Stick N 2.4

These devices require the 1-stage firmware, if not present we
don't continue.

Cc: Peter Grabienski <Peter.Grabienski@Atheros.com>
Cc: Stephen Chen <Stephen.Chen@Atheros.com>
Cc: Michael Fortin <Michael.Fortin@Atheros.com>
Cc: Johnny Cheng <Johnny.Cheng@Atheros.com>
Cc: Yuan-Gu Wei <Yuan-Gu.Wei@atheros.com>
Cc: Joerg Albert <jal2@gmx.de>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ar9170: add support for 1-stage firmware

You can get the stage 1 firmware from here:

http://www.kernel.org/pub/linux/kernel/people/mcgrof/firmware/ar9170/ar9170.fw

md5sum: 34feec4ec0eae3bb92c7c1ea2dfb4530
sha1sum: 6e5250498b815c2940d97242de31e054ae44e079

Its license:

http://www.kernel.org/pub/linux/kernel/people/mcgrof/firmware/ar9170/LICENSE

This is a new firmware, tested with WNDA3100.

Cc: Peter Grabienski <Peter.Grabienski@Atheros.com>
Cc: Stephen Chen <Stephen.Chen@Atheros.com>
Cc: Michael Fortin <Michael.Fortin@Atheros.com>
Cc: Johnny Cheng <Johnny.Cheng@Atheros.com>
Cc: Yuan-Gu Wei <Yuan-Gu.Wei@atheros.com>
Cc: Joerg Albert <jal2@gmx.de>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: Add sanity check for beacon_int in adhoc/mesh case

It looks like mac80211 can request the driver to start beaconing with
a beacon interval of zero in some cases (at least for mesh point). This
does not sound correct and something may need to be fixed in
mac80211. However, taken into account the unpleasantness of getting
stuck in an infinite busy loop with rtnl_lock held, let's add a quick
workaround in the driver to avoid the worst symptom while someone more
familiar with the mesh implementation can figure out what should be done
with mac80211 as far as beacon interval configuration is concerned.

Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath5k: remove conf->beacon_int usage

ieee80211_conf->beacon_int was deprecated and removed in a cleanup
patch, however it was accidentally added back to ath5k in the change
"ath5k: Allow user/driver to set txpower."  Remove it once more,
fixing the following warning:

[13091.968902] WARNING: at drivers/net/wireless/ath/ath5k/base.c:2167 warn_slowpath_null+0x15/0x1a()
[13091.968906] Hardware name: MacBook1,1
[13091.968909] Modules linked in: usb_storage fuse i915 drm af_packet acpi_cpufreq binfmt_misc dm_mirror dm_region_hash dm_log dm_multipath dm_mod snd_hda_codec_idt snd_hda_intel snd_hda_codec snd_seq_dummy hid_apple arc4 ecb snd_seq_oss snd_seq_midi_event usbhid snd_seq ath5k mac80211 appletouch snd_seq_device snd_pcm_oss snd_mixer_oss sky2 snd_pcm ath processor cfg80211 snd_timer sg ohci1394 snd uhci_hcd bitrev ieee1394 joydev ehci_hcd crc32 snd_page_alloc button ac thermal battery sr_mod applesmc cdrom evdev input_polldev unix [last unloaded: microcode]
[13091.968985] Pid: 2132, comm: phy0 Tainted: G        W  2.6.30-rc5-wl #118
[13091.968988] Call Trace:
[13091.968994]  [<c0125884>] warn_slowpath_fmt+0x77/0xa6
[13091.969003]  [<c03557d8>] ? _spin_unlock+0x2c/0x41
[13091.969008]  [<c0355a56>] ? _spin_lock_irqsave+0x15/0x69
[13091.969012]  [<c0355783>] ? _spin_unlock_irqrestore+0x34/0x5d
[13091.969019]  [<c01445bb>] ? trace_hardirqs_off+0xb/0xd
[13091.969024]  [<c0355783>] ? _spin_unlock_irqrestore+0x34/0x5d
[13091.969029]  [<c01445bb>] ? trace_hardirqs_off+0xb/0xd
[13091.969034]  [<c0355783>] ? _spin_unlock_irqrestore+0x34/0x5d
[13091.969039]  [<c01258c8>] warn_slowpath_null+0x15/0x1a
[13091.969054]  [<f965846d>] ath5k_beacon_update_timers+0x44/0x27f [ath5k]
[13091.969059]  [<c0126370>] ? vprintk+0x2dd/0x312
[13091.969063]  [<c0125e50>] ? release_console_sem+0x1a6/0x1d3
[13091.969076]  [<f96586c5>] ath5k_reset_tsf+0x1d/0x2c [ath5k]
[13091.969095]  [<f93f4426>] __ieee80211_sta_join_ibss+0x35/0x3aa [mac80211]
[13091.969102]  [<c0252793>] ? extract_entropy+0x47/0x8a
[13091.969121]  [<f93f4b21>] ieee80211_sta_find_ibss+0x2de/0x32f [mac80211]
[13091.969126]  [<c035422c>] ? mutex_lock_nested+0x28b/0x2a5
[13091.969145]  [<f93f4b8e>] ? ieee80211_ibss_notify_scan_completed+0x1c/0x6f [mac80211]
[13091.969164]  [<f93f4bc9>] ieee80211_ibss_notify_scan_completed+0x57/0x6f [mac80211]
[13091.969182]  [<f93f26da>] ieee80211_scan_completed+0x31a/0x33f [mac80211]
[13091.969201]  [<f93f27ca>] ieee80211_scan_work+0xcb/0x18b [mac80211]
[13091.969207]  [<c0133a6a>] worker_thread+0x1b1/0x28e
[13091.969212]  [<c0133a25>] ? worker_thread+0x16c/0x28e
[13091.969230]  [<f93f26ff>] ? ieee80211_scan_work+0x0/0x18b [mac80211]
[13091.969237]  [<c013736e>] ? autoremove_wake_function+0x0/0x38
[13091.969242]  [<c01338b9>] ? worker_thread+0x0/0x28e
[13091.969246]  [<c0137031>] kthread+0x4a/0x70
[13091.971460]  [<c0136fe7>] ? kthread+0x0/0x70
[13091.971467]  [<c0103527>] kernel_thread_helper+0x7/0x10
[13091.971470] ---[ end trace 8defaa5d15c50cef ]---

Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mac80211: handle -EALREADY on cfg80211 op assoc req

When the SME requests to associate to an open AP
ieee80211_sta_set_extra_ie() can be called with zero IE
length. When this happens or when the extra IE has already
been set -EALREADY is passed down and the supplicant will
complain that the operation is already in progress and it will
not let us associate. We correct this by treating -EALREADY
from ieee80211_sta_set_extra_ie() as a success just as we do
for wext.

Cc: Shan.Palanisamy@Atheros.com
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

wireless: libertas: fix unaligned accesses

Signed-off-by: Cliff Cai <cliff.cai@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: Add "debug" file to debugfs

This patch adds the debug file to the ath9k debugfs, which lets you modify
the debug_mask at runtime, without having to reload the ath9k module.

Signed-off-by: Jeff Hansen <x@jeffhansen.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: Combine legacy and 11n rc statistics

This patch combines the legacy and 11n rcstats into one, using the normal
rate table indices instead of two separate indices for each mode.  Legacy
rates also get all of the PER and retry information, now, too.

Signed-off-by: Jeff Hansen <x@jeffhansen.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: Reset SC_OP_TSF_RESET flag after stuck beacon

I have a TrendNet 652-BRP running OpenWRT + ath9k very well.  The only
problem is that the beacon gets stuck maybe once a day.  After
Vasanthakumar Thiagarajan's "ath9k: cleanup beacon parameters
configuration" patch, ath9k would nearly re-configure the beacons after it
detected the stuck beacon, and did a reset.  But it would fail the
SC_OP_TSF_RESET check in ath_beacon_config_ap.  This patch gets the beacon
fully reconfigured after the reset.

Signed-off-by: Jeff Hansen <x@jeffhansen.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

cfg80211: disallow interfering with stations on non-AP (part 2)

On non-AP interfaces userspace has no business interfering with
the station management, this can confuse mac80211 (and other
drivers probably wouldn't support it anyway). Allow adding and
removing stations only on AP interfaces.

(Reconcile this w/ previous version of patch posted with same
subject... -- JWL)

Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mac80211: fix transposed min/max CW values

I accidentally transposed these in the patch that "fixed" the defaults,
leading to extremely low throughput because of the huge min CW.

Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

iwmc3200wifi: fix printk format

Fix printk format for size_t variable:

drivers/net/wireless/iwmc3200wifi/fw.c:75: warning: format '%d' expects type 'int', but argument 4 has type 'size_t'

Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Cc: ilw@linux.intel.com
Acked-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

iwmc3200wifi: fix fragmentation threshold setting

We were sending the fragmentation threshold value to the wrong table,
causing an LMAC assert when setting it from wext.

Signed-off-by: Samuel Ortiz <samuel.ortiz@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

iwlwifi: avoid build warning in iwl-core.

When building when CONFIG_IWLWIFI_DEBUG is not set, we get the following
warning:
/work/src/w/drivers/net/wireless/iwlwifi/iwl-core.c: In function ‘iwl_isr’:
/work/src/w/drivers/net/wireless/iwlwifi/iwl-core.c:1707: warning:
unused variable ‘inta_fh’

This patch avoids this warning by adding #ifdef CONFIG_IWLWIFI_DEBUG
before the declaration of inta_fh in iwl_isr() in
drivers/net/wireless/iwlwifi/iwl-core.c

Signed-off-by: Rami Rosen <ramirose@gmail.com>
Acked-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

cfg80211: use key size constants

Instead of hardcoding the key length for validation, use the
constants Zhu Yi recently added and add one for AES_CMAC too.

Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

nl80211: bounce scan request back to userspace

When a scan finishes only the program that asked for it
knows what kind of scan it was; let's tell everybody else
about the scan parameters as well so they can evaluate
the result of the scan better. Also helps with debugging.

Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

cfg80211: validate AID of stations being added

We have some validation code in mac80211 but said code will
force an invalid AID to 0 which isn't a valid AID either;
instead require a valid AID (1-2007) to be passed in from
userspace in cfg80211 already. Also move the code before
the race comment since it can only be executed during STA
addition and thus is not racy.

Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rt2x00: Remove last usage of beacon_int from ieee80211_config

This removes the last usage of beacon_int inside the iee80211_config
structure from rt2x00. The attempt is a bit hackish, and subject to
change in the future when the entire rt2x00_dev structure is
cleaned up and restructured.

Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mac80211: deprecate conf.beacon_int properly

Ivo has updated the driver to no longer use the change flag,
so we can remove that, but rt2x00 and ath5k still use the
actual value so let's mark it as deprecated too.

Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

libertas: fix WPA adhoc network creation

Oddly enough, the firmware's JOIN/START commands don't appear to have
any facility for setting custom IEs, thus the started adhoc network
doesn't advertise its WPA capability in the beacon.  Whee!

Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

libertas: convert CMD_802_11_ASSOCIATE to a direct command

Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

libertas: convert CMD_802_11_AUTHENTICATE to a direct command

And fix up setting authentication suite for v9+ firmware too.

Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

libertas: restyle Marvell & IEEE TLV structure names

Easier to read and more conformant with kernel style.

Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

libertas: simplify and clean up association/start/join setup

Some of the parameters for association/join/start commands aren't
used (like the FH and CF IEs for IBSS, and the FH IE for BSS), so
get rid of their unions to reduce indirection.  Also clean up
structure names for kernel style.

Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

iwlwifi: fix otp access init

Polling function returns positive time if polling was needed to
read value. This is still success.

Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
CC: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

iwlwifi: fix merge error

This hunk of code was removed in patch "iwlwifi: do not
cancel delayed work inside spin_lock_irqsave" submitted at
http://marc.info/?l=linux-wireless&m=124267503030042&w=2

This same patch in this repo does not remove this hunk.
Remove it here.

Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rt2x00: Add new rt2800usb USB ID's

new patch to add more usb_dev to rt2800usb.c .
IDs 'stolen' from the latest Ralink linux
driver(2009_0520_RT3070_Linux_STA_v2.1.1.0.tar.gz)

Signed-off-by: Xose Vazquez Perez <xose.vazquez@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

net/libertas: make SPI interface big endian aware

The comment (which I remove) says that the translation is done SPI routines.
IMHO this can't work because the SPI driver does not know whether the incomming
bytes are part of the registers/bytes which need to be flipped or part of
packet data which has to remain untouched.
While adding le helpers I also removed spu_write_u32() which has no users.

Tested-by: Andrey Yurovsky <andrey@cozybit.com>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath5k: avoid leaking mutex in ath5k_config

Reported-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

sctp: support non-blocking version of the new sctp_connectx() API

Prior implementation of the new sctp_connectx() call that returns
an association ID did not work correctly on non-blocking socket.
This is because we could not return both a EINPROGRESS error and
an association id.  This is a new implementation that supports this.

Originally from Ivan Skytte Jørgensen <isj-sctp@i1.dk

Signed-off-by: Ivan Skytte Jørgensen <isj-sctp@i1.dk
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>

sctp: fix to choose alternate destination when retransmit ASCONF chunk

RFC 5061 Section 5.1 ASCONF Chunk Procedures said:

B4)  Re-transmit the ASCONF Chunk last sent and if possible choose an
     alternate destination address (please refer to [RFC4960],
     Section 6.4.1).  An endpoint MUST NOT add new parameters to this
     chunk; it MUST be the same (including its Sequence Number) as
     the last ASCONF sent.  An endpoint MAY, however, bundle an
     additional ASCONF with new ASCONF parameters with the next
     Sequence Number.  For details, see Section 5.5.

This patch fix to choose an alternate destination address when
re-transmit the ASCONF chunk, with some dup codes cleanup.

Signed-off-by: Wei Yongjun <yjwei@cn.fujitsu.com>
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>

sctp: fix sack_timeout sysctl min and max types

sctp_sack_timeout is defined as int, but the sysctl's maxsize is set
to sizeof(long) and the min/max are defined as long.

Signed-off-by: jean-mickael.guerin@6wind.com
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>

sctp: fix panic when T4-rto timer expire on removed transport

If T4-rto timer is expired on a removed transport, kernel panic
will occur when we do failure management on that transport.
You can reproduce this use the following sequence:

Endpoint A                           Endpoint B
(ESTABLISHED)                        (ESTABLISHED)

            <-----------------      ASCONF
                                    (SRC=X)
ASCONF        ----------------->
(Delete IP Address = X)
            <-----------------      ASCONF-ACK
                                    (Success Indication)
            <-----------------      ASCONF
                                    (T4-rto timer expire)

This patch fixed the problem.

Signed-off-by: Wei Yongjun <yjwei@cn.fujitsu.com>
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>

sctp: fix panic when T2-shutdown timer expire on removed transport

If T2-shutdown timer is expired on a removed transport, kernel
panic will occur when we do failure management on that transport.
You can reproduce this use the following sequence:

  Endpoint A                           Endpoint B
  (ESTABLISHED)                        (ESTABLISHED)

                <-----------------      SHUTDOWN
                                        (SRC=X)
  ASCONF        ----------------->
  (Delete IP Address = X)
                <-----------------      ASCONF-ACK
                                        (Success Indication)
                <-----------------      SHUTDOWN
                                        (T2-shutdown timer expire)
This patch fixed the problem.

Signed-off-by: Wei Yongjun <yjwei@cn.fujitsu.com>
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>

sctp: fix to only enable IPv6 address support on PF_INET6 socket

If socket is create by PF_INET type, it can not used IPv6 address
to send/recv DATA. So only enable IPv6 address support on PF_INET6
socket.

Signed-off-by: Wei Yongjun <yjwei@cn.fujitsu.com>
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>

sctp: fix a typo in net/sctp/sm_statetable.c

Just fix a typo in net/sctp/sm_statetable.c.

Signed-off-by: Wei Yongjun <yjwei@cn.fujitsu.com>
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>

sctp: fix the error code when ASCONF is received with invalid address

Use Unresolvable Address error cause instead of Invalid Mandatory
Parameter error cause when process ASCONF chunk with invalid address
since address parameters are not mandatory in the ASCONF chunk.

Signed-off-by: Wei Yongjun <yjwei@cn.fujitsu.com>
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>

sctp: fix report unrecognized parameter in ACSONF-ACK

RFC5061 Section 5.2.  Upon Reception of an ASCONF Chunk

V2)  In processing the chunk, the receiver should build a
     response message with the appropriate error TLVs, as
     specified in the Parameter type bits, for any ASCONF
     Parameter it does not understand.  To indicate an
     unrecognized parameter, Cause Type 8 should be used as
     defined in the ERROR in Section 3.3.10.8, [RFC4960].  The
     endpoint may also use the response to carry rejections for
     other reasons, such as resource shortages, etc., using the
     Error Cause TLV and an appropriate error condition.

So we should indicate an unrecognized parameter with error
SCTP_ERROR_UNKNOWN_PARAM in ACSONF-ACK chunk, not
SCTP_ERROR_INV_PARAM.

Signed-off-by: Wei Yongjun <yjwei@cn.fujitsu.com>
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>

sctp: fix error cause codes of ADD-IP extension

RFC5061 had changed the error cause codes for Dynamic Address
Reconfiguration As the following:

       Cause Code
       Value          Cause Code
       ---------      ----------------
       0x00A0          Request to Delete Last Remaining IP Address
       0x00A1          Operation Refused Due to Resource Shortage
       0x00A2          Request to Delete Source IP Address
       0x00A3          Association Aborted Due to Illegal ASCONF-ACK
       0x00A4          Request Refused - No Authorization

This patch fix the error cause codes.

Signed-off-by: Wei Yongjun <yjwei@cn.fujitsu.com>
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>

net/ucc_geth: Add SGMII support for UEC GETH driver

Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

fsl_pq_mido: Set the first UCC as the mii management interface master

Current code makes the UCC whose register range includes the current mdio
register to be the MII managemnt interface master of the QE. If there is more
than one mdio bus for QE, the UCC of the last mdio bus will be the MII
management interface master which will make the primary mdio bus working
unproperly, e.g. can not get the right clock. Normally the primary mdio bus is
the first UEC's mdio bus.
This patch allows the first UCC to be the MII management interface master of the
multiple UCC mdio buses.

Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net/phy/marvell: update m88e1111 support for SGMII mode

Disable fiber/copper auto selection for Marvell m88e1111 SGMII support.

Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>