linux-2.6
15 years agoadt7470: make automatic fan control really work
Darrick J. Wong [Tue, 6 Jan 2009 22:41:34 +0000 (14:41 -0800)] 
adt7470: make automatic fan control really work

It turns out that the adt7470's automatic fan control algorithm only works
when the temperature sensors get updated.  This in turn happens only when
someone tells the chip to read its temperature sensors.  Regrettably, this
means that we have to drive the chip periodically.

Signed-off-by: Darrick J. Wong <djwong@us.ibm.com>
Cc: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
15 years agoadt7470: observe the number of temperature sensors to shorten update time
Darrick J. Wong [Tue, 6 Jan 2009 22:41:33 +0000 (14:41 -0800)] 
adt7470: observe the number of temperature sensors to shorten update time

The adt7470 driver currently assumes that 1s is the proper time to wait to
read all temperature sensors.  However, the correct time is 200ms *
number_of_sensors.  This patch sets the default time to provide for 10
sensors and then lowers it based on the number of sensor inputs that have
nozero values.

Signed-off-by: Darrick J. Wong <djwong@us.ibm.com>
Cc: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
15 years agoadt7470: fix pwm at a certain level during temperature sensor scan
Darrick J. Wong [Tue, 6 Jan 2009 22:41:32 +0000 (14:41 -0800)] 
adt7470: fix pwm at a certain level during temperature sensor scan

In the small window that it takes to read the temperature sensors, the pwm
outputs momentarily drop to 0.  This causes a noticeable hiccup in fan
speed, which is slightly annoying.  The solution is to manually program
the pwm output with whatever the automatic value is and then shift the
fans to manual control while reading temperatures.  Once that is done, put
the fans back to whatever mode of control was there before.

Signed-off-by: Darrick J. Wong <djwong@us.ibm.com>
Cc: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
15 years agoadt74{62, 70, 73}: Use DIV_ROUND_CLOSEST for rounded division
Darrick J. Wong [Tue, 6 Jan 2009 22:41:31 +0000 (14:41 -0800)] 
adt74{62, 70, 73}: Use DIV_ROUND_CLOSEST for rounded division

Modify some hwmon drivers to use DIV_ROUND_CLOSEST instead of bloating
source with (naughty) macros.

Signed-off-by: Darrick J. Wong <djwong@us.ibm.com>
Cc: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
15 years agocheckpatch: version: 0.26
Andy Whitcroft [Tue, 6 Jan 2009 22:41:30 +0000 (14:41 -0800)] 
checkpatch: version: 0.26

Signed-off-by: Andy Whitcroft <apw@canonical.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
15 years agocheckpatch: fix the perlcritic errors
Andy Whitcroft [Tue, 6 Jan 2009 22:41:30 +0000 (14:41 -0800)] 
checkpatch: fix the perlcritic errors

Clean up checkpatch using perlcritic.

Signed-off-by: Andy Whitcroft <apw@canonical.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
15 years agocheckpatch: struct file_operations should normally be const
Andy Whitcroft [Tue, 6 Jan 2009 22:41:29 +0000 (14:41 -0800)] 
checkpatch: struct file_operations should normally be const

In the general use case struct file_operations should be a const object.
Check for and warn where it is not.  As suggested by Steven and Ingo.

Acked-by: Steven Rostedt <rostedt@goodmis.org>
Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andy Whitcroft <apw@canonical.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
15 years agocheckpatch: ensure we actually detect if assignments split across lines
Andy Whitcroft [Tue, 6 Jan 2009 22:41:29 +0000 (14:41 -0800)] 
checkpatch: ensure we actually detect if assignments split across lines

When checking for assignments within if conditionals we check the whole of
the condition, but the match is performed using a line constrained regular
expression.  This means we can miss split conditionals or those on the
second line.  Allow the check to span lines.

Signed-off-by: Andy Whitcroft <apw@canonical.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
15 years agocheckpatch: do not report nr_static as a static declaration
Andy Whitcroft [Tue, 6 Jan 2009 22:41:28 +0000 (14:41 -0800)] 
checkpatch: do not report nr_static as a static declaration

Ensure we do not report identifiers containing the word static as static
declarations.  For example this should not be reported as an unecessary
assignement of 0:

long nr_static = 0;

Signed-off-by: Andy Whitcroft <apw@canonical.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
15 years agocheckpatch: track #ifdef/#else/#endif when tracking blocks
Andy Whitcroft [Tue, 6 Jan 2009 22:41:27 +0000 (14:41 -0800)] 
checkpatch: track #ifdef/#else/#endif when tracking blocks

When picking up a complete statement or block for analysis we cannot
simply track open/close/etc parenthesis we must take into account
preprocessor section boundaries.

Signed-off-by: Andy Whitcroft <apw@canonical.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
15 years agocheckpatch: fix continuation detection when handling spacing on operators
Andy Whitcroft [Tue, 6 Jan 2009 22:41:27 +0000 (14:41 -0800)] 
checkpatch: fix continuation detection when handling spacing on operators

We are miscategorising a continuation fragment following an operator
which may lead to us thinking that there is a space after it when there is
not.  Fix this up.

Signed-off-by: Andy Whitcroft <apw@canonical.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
15 years agocheckpatch: loosen spacing on typedef function checks
Andy Whitcroft [Tue, 6 Jan 2009 22:41:26 +0000 (14:41 -0800)] 
checkpatch: loosen spacing on typedef function checks

Loosen spacing checks to correctly detect this valid use of a typedef:

typedef struct rcu_data *(*get_data_func)(int);

Signed-off-by: Andy Whitcroft <apw@canonical.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
15 years agocheckpatch: try to catch missing VMLINUX_SYMBOL() in vmlinux.lds.h
Mike Frysinger [Tue, 6 Jan 2009 22:41:25 +0000 (14:41 -0800)] 
checkpatch: try to catch missing VMLINUX_SYMBOL() in vmlinux.lds.h

Seems like every other release we have someone who updates vmlinux.lds.h
and adds C-visible symbols without VMLINUX_SYMBOL() around them.  So start
checking the file and reject assignments which have plain symbols on
either side.

[apw@canonical.com: soften the check, add tests]
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Andy Whitcroft <apw@canonical.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
15 years agocheckpatch: allow parentheses on return for comparisons
Andy Whitcroft [Tue, 6 Jan 2009 22:41:24 +0000 (14:41 -0800)] 
checkpatch: allow parentheses on return for comparisons

It seems to be a common idiom to include braces on conditionals in all
contexts including return.  Allow this exception to the return is not a
function checks.  Reported by Kay Sievers.

Cc: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Andy Whitcroft <apw@canonical.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
15 years agocheckpatch: Add warning for p0-patches
Wolfram Sang [Tue, 6 Jan 2009 22:41:24 +0000 (14:41 -0800)] 
checkpatch: Add warning for p0-patches

Some people work internally with -p0-patches which has the danger that one
forgets to convert them to -p1 before mainlining.  Bitten myself and seen
p0-patches in mailing lists occasionally, this patch adds a warning to
checkpatch.pl in case a patch is -p0.  If you really want, you can fool
this check to generate false positives, this is why it just spits a
warning.  Making the check 100% proof is trickier than it looks, so let's
start with a version which catches the cases of real use.

[apw@canonical.com: update message language, handle null prefix, add tests]
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Andy Whitcroft <apw@canonical.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
15 years agocheckpatch: update copyrights
Andy Whitcroft [Tue, 6 Jan 2009 22:41:23 +0000 (14:41 -0800)] 
checkpatch: update copyrights

Signed-off-by: Andy Whitcroft <apw@canonical.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
15 years agocheckpatch: update MAINTAINERS entry
Andy Whitcroft [Tue, 6 Jan 2009 22:41:22 +0000 (14:41 -0800)] 
checkpatch: update MAINTAINERS entry

Update my email address to my new work address.  Also, as per our recent
email conversation remove Randy and Joel from the maintainers list.
Finally add LKML so that emails are recorded somewhere.

Signed-off-by: Andy Whitcroft <apw@shadowen.org>
Cc: Randy Dunlap <rdunlap@xenotime.net>
Cc: Joel Schopp <jschopp@austin.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
15 years agocheckpatch: version: 0.25
Andy Whitcroft [Tue, 6 Jan 2009 22:41:21 +0000 (14:41 -0800)] 
checkpatch: version: 0.25

Signed-off-by: Andy Whitcroft <apw@shadowen.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
15 years agocheckpatch: dissallow spaces between stars in pointer types
Andy Whitcroft [Tue, 6 Jan 2009 22:41:21 +0000 (14:41 -0800)] 
checkpatch: dissallow spaces between stars in pointer types

Disallow spaces within multiple pointer stars (*) in both casts and
definitions.  Both of these would now be reported:

(char * *)
char * *foo;

Also now consistently detects and reports the attributes within these
structures making the error report itself clearer.

Signed-off-by: Andy Whitcroft <apw@shadowen.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
15 years agocheckpatch: comment ends inside strings is most likely not an open comment
Andy Whitcroft [Tue, 6 Jan 2009 22:41:20 +0000 (14:41 -0800)] 
checkpatch: comment ends inside strings is most likely not an open comment

When we are detecting whether a comment is open when we start a hunk we
check for the first comment edge in the hunk and assume its inverse.
However if the hunk contains something like below, then we will assume
that a comment was open.  Update this heuristic to see if the comment edge
is obviously within double quotes and ignore it if so:

foo(" */);

Signed-off-by: Andy Whitcroft <apw@shadowen.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
15 years agocheckpatch: detect multiple bitfield declarations
Andy Whitcroft [Tue, 6 Jan 2009 22:41:19 +0000 (14:41 -0800)] 
checkpatch: detect multiple bitfield declarations

Detect the colons (:) which make up secondary bitfield declarations and
apply binary colon checks.  For example the following is common idiom:

int foo:1,
    bar:1;

Signed-off-by: Andy Whitcroft <apw@shadowen.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
15 years agocheckpatch: __weak is an official attribute
Andy Whitcroft [Tue, 6 Jan 2009 22:41:18 +0000 (14:41 -0800)] 
checkpatch: __weak is an official attribute

Add __weak as an official attribute.  This tends to be used in a location
where the automated attribute detector misses it.

Signed-off-by: Andy Whitcroft <apw@shadowen.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
15 years agocheckpatch: structure member assignments are not complex
Andy Whitcroft [Tue, 6 Jan 2009 22:41:18 +0000 (14:41 -0800)] 
checkpatch: structure member assignments are not complex

Ensure we do not trigger the complex macros checks on structure member
assignment, for example:

#define foo .bar = 10

Signed-off-by: Andy Whitcroft <apw@shadowen.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
15 years agocheckpatch: widen implied comment detection to allow multiple stars
Andy Whitcroft [Tue, 6 Jan 2009 22:41:17 +0000 (14:41 -0800)] 
checkpatch: widen implied comment detection to allow multiple stars

Some people use double star '**' as a comment continuation, and start
comments with complete lines of stars.  Widen the implied comment
detection to pick these up.

Signed-off-by: Andy Whitcroft <apw@shadowen.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
15 years agocheckpatch: comment detection may miss an implied comment on the last hunk
Andy Whitcroft [Tue, 6 Jan 2009 22:41:16 +0000 (14:41 -0800)] 
checkpatch: comment detection may miss an implied comment on the last hunk

When detecting implied comments from leading stars we may incorrectly
think we have detected an edge one way or the other when we have not if we
drop off the end of the last hunk.  Fix this up.

Signed-off-by: Andy Whitcroft <apw@shadowen.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
15 years agocheckpatch: add checks for in_atomic()
Andy Whitcroft [Tue, 6 Jan 2009 22:41:16 +0000 (14:41 -0800)] 
checkpatch: add checks for in_atomic()

in_atomic() is not for driver use so report any such use as an ERROR.
Also in_atomic() is often used to determine if we may sleep, but it is not
reliable in this use model therefore strongly discourage its use.

Signed-off-by: Andy Whitcroft <apw@shadowen.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
15 years agofs: fix function param name in kernel-doc
Randy Dunlap [Tue, 6 Jan 2009 22:41:15 +0000 (14:41 -0800)] 
fs: fix function param name in kernel-doc

Fix function parameter name in kernel-doc:

Warning(linux-2.6.28-git5//fs/block_dev.c:1272): No description found for parameter 'pathname'
Warning(linux-2.6.28-git5//fs/block_dev.c:1272): Excess function parameter 'path' description in 'lookup_bdev'

Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
15 years agoinclude/linux/interrupt.h: do not include linux/irqnr.h twice
Jesper Juhl [Tue, 6 Jan 2009 22:41:14 +0000 (14:41 -0800)] 
include/linux/interrupt.h: do not include linux/irqnr.h twice

Signed-off-by: Jesper Juhl <jj@chaosbits.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
15 years agosysrq: more explicit, less terse help messages
Randy Dunlap [Tue, 6 Jan 2009 22:41:13 +0000 (14:41 -0800)] 
sysrq: more explicit, less terse help messages

Eliminate sysrq terse help mode; make sysrq help messages more meaningful
(more explicit/verbose).  Make the sysrq action letter clearer by listing
it explicitly in more sysrq help messages (when it is not simple/clear).

The SysRq help message now looks like this:

SysRq : HELP : loglevel(0-9) reBoot terminate-all-tasks(E) memory-full-oom-kill(F) kill-all-tasks(I) saK show-backtrace-all-active-cpus(L) show-memory-usage(M) nice-all-RT-tasks(N) powerOff show-registers(P) show-all-timers(Q) unRaw Sync show-task-states(T) Unmount show-blocked-tasks(W)

Addresses http://bugs.debian.org/cgi-bin/bugreport.cgi?bug=330403.

Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Cc: <jidanni@jidanni.org>
Cc: <330403@bugs.debian.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
15 years agofs/inode: fix kernel-doc notation
Randy Dunlap [Tue, 6 Jan 2009 22:41:13 +0000 (14:41 -0800)] 
fs/inode: fix kernel-doc notation

Fix kernel-doc notation:

Warning(linux-2.6.28-git3//fs/inode.c:120): No description found for parameter 'sb'
Warning(linux-2.6.28-git3//fs/inode.c:120): No description found for parameter 'inode'
Warning(linux-2.6.28-git3//fs/inode.c:588): No description found for parameter 'sb'
Warning(linux-2.6.28-git3//fs/inode.c:588): No description found for parameter 'inode'

Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
15 years agoRemove obsolete CONFIG_RESOURCES_64BIT
Geert Uytterhoeven [Tue, 6 Jan 2009 22:41:12 +0000 (14:41 -0800)] 
Remove obsolete CONFIG_RESOURCES_64BIT

commit 8308c54d7e312f7a03e2ce2057d0837e6fe3843f ("generic: redefine
resource_size_t as phys_addr_t") made CONFIG_RESOURCES_64BIT obsolete, but
didn't remove it. Remove it.

Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Jeremy Fitzhardinge <jeremy@goop.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
15 years agodo_coredump(): check return from argv_split()
Tetsuo Handa [Tue, 6 Jan 2009 22:41:11 +0000 (14:41 -0800)] 
do_coredump(): check return from argv_split()

do_coredump() accesses helper_argv[0] without checking helper_argv !=
NULL.  This can happen if page allocation failed.

Signed-off-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
15 years agoprofile: don't include <asm/ptrace.h> twice.
KOSAKI Motohiro [Tue, 6 Jan 2009 22:41:10 +0000 (14:41 -0800)] 
profile: don't include <asm/ptrace.h> twice.

Currently, kernel/profile.c include <asm/ptrace.h> twice.  It can be
removed.

Signed-off-by: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
15 years agoinit/main.c: mark late_time_init as __initdata
Jan Beulich [Tue, 6 Jan 2009 22:41:10 +0000 (14:41 -0800)] 
init/main.c: mark late_time_init as __initdata

Signed-off-by: Jan Beulich <jbeulich@novell.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
15 years agoadd missing accounting calls to compat_sys_{readv,writev}
Gerd Hoffmann [Tue, 6 Jan 2009 22:41:09 +0000 (14:41 -0800)] 
add missing accounting calls to compat_sys_{readv,writev}

Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Cc: Jay Lan <jlan@engr.sgi.com>
Cc: Balbir Singh <balbir@in.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
15 years agofs: fix name overwrite in __register_chrdev_region()
Cyrill Gorcunov [Tue, 6 Jan 2009 22:41:08 +0000 (14:41 -0800)] 
fs: fix name overwrite in __register_chrdev_region()

It's possible to register a chrdev with a name size exactly the same as
was allocated in structure.  It seems it was not intended behaviour.

At least chrdev_show does not like it.

Signed-off-by: Cyrill Gorcunov <gorcunov@gmail.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
15 years agoremove linux/hardirq.h from asm-generic/local.h
Russell King [Tue, 6 Jan 2009 22:41:07 +0000 (14:41 -0800)] 
remove linux/hardirq.h from asm-generic/local.h

While looking at reducing the amount of architecture namespace pollution
in the generic kernel, I found that asm/irq.h is included in the vast
majority of compilations on ARM (around 650 files.)

Since asm/irq.h includes a sub-architecture include file on ARM, this
causes a negative impact on the ccache's ability to re-use the build
results from other sub-architectures, so we have a desire to reduce the
dependencies on asm/irq.h.

It turns out that a major cause of this is the needless include of
linux/hardirq.h into asm-generic/local.h.  The patch below removes this
include, resulting in some 250 to 300 files (around half) of the kernel
then omitting asm/irq.h.

My test builds still succeed, provided two ARM files are fixed
(arch/arm/kernel/traps.c and arch/arm/mm/fault.c) - so there may be
negative impacts for this on other architectures.

Note that x86 does not include asm/irq.h nor linux/hardirq.h in its
asm/local.h, so this patch can be viewed as bringing the generic version
into line with the x86 version.

[kosaki.motohiro@jp.fujitsu.com: add #include <linux/irqflags.h> to acpi/processor_idle.c]
[adobriyan@gmail.com: fix sparc64]
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
15 years agoioc4: automatically load sgiioc4 subordinate module
Brent Casavant [Tue, 6 Jan 2009 22:41:06 +0000 (14:41 -0800)] 
ioc4: automatically load sgiioc4 subordinate module

Modify ioc4 to always load the sgiioc4 IDE module if the board carrying
the IOC4 hardware actually implements the IDE interface (not all boards
bring this functionality off the IOC4 chip).  A drive hosted on the IDE
interface may contain the root filesystem, and sgiioc4 doesn't load
automatically as ioc4 owns the PCI device ID, not sgiioc4.

[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: Michael Reed <mdr@sgi.com>
Signed-off-by: Brent Casavant <bcasavan@sgi.com>
Cc: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
15 years agoDmitry has been renamed
Dmitry Eremin-Solenikov [Tue, 6 Jan 2009 22:41:05 +0000 (14:41 -0800)] 
Dmitry has been renamed

My surname has changed due to marriage. Change MAINTAINERS entry
and add .mailmap entry to reflect that.

Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
15 years agopercpu_counter: FBC_BATCH should be a variable
Eric Dumazet [Tue, 6 Jan 2009 22:41:04 +0000 (14:41 -0800)] 
percpu_counter: FBC_BATCH should be a variable

For NR_CPUS >= 16 values, FBC_BATCH is 2*NR_CPUS

Considering more and more distros are using high NR_CPUS values, it makes
sense to use a more sensible value for FBC_BATCH, and get rid of NR_CPUS.

A sensible value is 2*num_online_cpus(), with a minimum value of 32 (This
minimum value helps branch prediction in __percpu_counter_add())

We already have a hotcpu notifier, so we can adjust FBC_BATCH dynamically.

We rename FBC_BATCH to percpu_counter_batch since its not a constant
anymore.

Signed-off-by: Eric Dumazet <dada1@cosmosbay.com>
Acked-by: David S. Miller <davem@davemloft.net>
Acked-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
15 years agoAllow times and time system calls to return small negative values
Paul Mackerras [Tue, 6 Jan 2009 22:41:02 +0000 (14:41 -0800)] 
Allow times and time system calls to return small negative values

At the moment, the times() system call will appear to fail for a period
shortly after boot, while the value it want to return is between -4095 and
-1.  The same thing will also happen for the time() system call on 32-bit
platforms some time in 2106 or so.

On some platforms, such as x86, this is unavoidable because of the system
call ABI, but other platforms such as powerpc have a separate error
indication from the return value, so system calls can in fact return small
negative values without indicating an error.  On those platforms,
force_successful_syscall_return() provides a way to indicate that the
system call return value should not be treated as an error even if it is
in the range which would normally be taken as a negative error number.

This adds a force_successful_syscall_return() call to the time() and
times() system calls plus their 32-bit compat versions, so that they don't
erroneously indicate an error on those platforms whose system call ABI has
a separate error indication.  This will not affect anything on other
platforms.

Joakim Tjernlund added the fix for time() and the compat versions of
time() and times(), after I did the fix for times().

Signed-off-by: Joakim Tjernlund <Joakim.Tjernlund@transmode.se>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Acked-by: David S. Miller <davem@davemloft.net>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
15 years agodocumentation: when to BUG(), and when to not BUG()
David Brownell [Tue, 6 Jan 2009 22:41:01 +0000 (14:41 -0800)] 
documentation: when to BUG(), and when to not BUG()

Provide some basic advice about when to use BUG()/BUG_ON(): never, unless
there's really no better option.

This matches my understanding of the standard policy ...  which seems not
to be written down so far, outside of LKML messages that I haven't
bookmarked.

Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: Hans Verkuil <hverkuil@xs4all.nl>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Arjan van de Ven <arjan@infradead.org>
Cc: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
15 years agopoll: allow f_op->poll to sleep
Tejun Heo [Tue, 6 Jan 2009 22:40:59 +0000 (14:40 -0800)] 
poll: allow f_op->poll to sleep

f_op->poll is the only vfs operation which is not allowed to sleep.  It's
because poll and select implementation used task state to synchronize
against wake ups, which doesn't have to be the case anymore as wait/wake
interface can now use custom wake up functions.  The non-sleep restriction
can be a bit tricky because ->poll is not called from an atomic context
and the result of accidentally sleeping in ->poll only shows up as
temporary busy looping when the timing is right or rather wrong.

This patch converts poll/select to use custom wake up function and use
separate triggered variable to synchronize against wake up events.  The
only added overhead is an extra function call during wake up and
negligible.

This patch removes the one non-sleep exception from vfs locking rules and
is beneficial to userland filesystem implementations like FUSE, 9p or
peculiar fs like spufs as it's very difficult for those to implement
non-sleeping poll method.

While at it, make the following cosmetic changes to make poll.h and
select.c checkpatch friendly.

* s/type * symbol/type *symbol/    : three places in poll.h
* remove blank line before EXPORT_SYMBOL() : two places in select.c

Oleg: spotted missing barrier in poll_schedule_timeout()
Davide: spotted missing write barrier in pollwake()

Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Eric Van Hensbergen <ericvh@gmail.com>
Cc: Ron Minnich <rminnich@sandia.gov>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Christoph Hellwig <hch@infradead.org>
Signed-off-by: Miklos Szeredi <mszeredi@suse.cz>
Cc: Davide Libenzi <davidel@xmailserver.org>
Cc: Brad Boyer <flar@allandria.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Roland McGrath <roland@redhat.com>
Cc: Mauro Carvalho Chehab <mchehab@infradead.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Cc: Davide Libenzi <davidel@xmailserver.org>
Cc: Oleg Nesterov <oleg@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
15 years agofs: use menuconfig to control the Misc. filesystems menu
Randy Dunlap [Tue, 6 Jan 2009 22:40:57 +0000 (14:40 -0800)] 
fs: use menuconfig to control the Misc. filesystems menu

Have one option to control Miscellaneous filesystems.  This makes it easy
to disable all of them at one time.

Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
15 years agoscripts: script from kerneloops.org to pretty print oops dumps
Arjan van de Ven [Tue, 6 Jan 2009 22:40:57 +0000 (14:40 -0800)] 
scripts: script from kerneloops.org to pretty print oops dumps

We're struggling all the time to figure out where the code came from that
oopsed..  The script below (a adaption from a script used by
kerneloops.org) can help developers quite a bit, at least for non-module
cases.

It works and looks like this:

[/home/arjan/linux]$ dmesg | perl scripts/markup_oops.pl vmlinux
 {
  struct agp_memory *memory;

  memory = agp_allocate_memory(agp_bridge, pg_count, type);
 c055c10f: 89 c2                 mov    %eax,%edx
  if (memory == NULL)
 c055c111: 74 19                 je     c055c12c <agp_allocate_memory_wrap+0x30>
 /* This function must only be called when current_controller != NULL */
 static void agp_insert_into_pool(struct agp_memory * temp)
 {
  struct agp_memory *prev;

  prev = agp_fe.current_controller->pool;
 c055c113: a1 ec dc 8f c0        mov    0xc08fdcec,%eax
*c055c118: 8b 40 10              mov    0x10(%eax),%eax     <----- faulting instruction

  if (prev != NULL) {
 c055c11b: 85 c0                 test   %eax,%eax
 c055c11d: 74 05                 je     c055c124 <agp_allocate_memory_wrap+0x28>
  prev->prev = temp;
 c055c11f: 89 50 04              mov    %edx,0x4(%eax)
  temp->next = prev;
 c055c122: 89 02                 mov    %eax,(%edx)
  }
  agp_fe.current_controller->pool = temp;
 c055c124: a1 ec dc 8f c0        mov    0xc08fdcec,%eax
 c055c129: 89 50 10              mov    %edx,0x10(%eax)
  if (memory == NULL)
  return NULL;

  agp_insert_into_pool(memory);

so in this case, we faulted while dereferencing agp_fe.current_controller
pointer, and we get to see exactly which function and line it affects...
Personally I find this very useful, and I can see value for having this
script in the kernel for more-than-just-me to use.

Caveats:
* It only works for oopses not-in-modules
* It only works nicely for kernels compiled with CONFIG_DEBUG_INFO
* It's not very fast.
* It only works on x86

Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
15 years agooops: increment the oops UUID every time we oops
Arjan van de Ven [Tue, 6 Jan 2009 22:40:54 +0000 (14:40 -0800)] 
oops: increment the oops UUID every time we oops

... because we do want repeated same-oops to be seen by automated
tools like kerneloops.org

Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
15 years agostrict_strto* is not strict enough
Pavel Machek [Tue, 6 Jan 2009 22:40:53 +0000 (14:40 -0800)] 
strict_strto* is not strict enough

It decodes "\n" as 0, which is bad, because stray echo into backlight
will turn your backlight off, etc...

Signed-off-by: Pavel Machek <pavel@suse.cz>
Cc: Yi Yang <yi.y.yang@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
15 years agoautodetect_raid: add missing __init marking
Mike Frysinger [Tue, 6 Jan 2009 22:40:53 +0000 (14:40 -0800)] 
autodetect_raid: add missing __init marking

The function autodetect_raid is only used by __init functions, and it refers
to __initdata, so it needs __init markings.  Fixes this error:
The function autodetect_raid() references
the variable __initdata raid_noautodetect.
This is often because autodetect_raid lacks a __initdata
annotation or the annotation of raid_noautodetect is wrong.

Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
15 years agosamples: mark {static|__init|__exit} for {init|exit} functions
Qinghuang Feng [Tue, 6 Jan 2009 22:40:52 +0000 (14:40 -0800)] 
samples: mark {static|__init|__exit} for {init|exit} functions

None of these (init|exit) functions is called from other functions which
is outside the kernel module mechanism or kernel itself, so mark them as
{static|__init|__exit}.

Signed-off-by: Qinghuang Feng <qhfeng.kernel@gmail.com>
Cc: Mathieu Desnoyers <mathieu.desnoyers@polymtl.ca>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
15 years agoCreate a DIV_ROUND_CLOSEST macro to do division with rounding
Darrick J. Wong [Tue, 6 Jan 2009 22:40:51 +0000 (14:40 -0800)] 
Create a DIV_ROUND_CLOSEST macro to do division with rounding

Create a helper macro to divide two numbers and round the result to the
nearest whole number.  This is a helper macro for hwmon drivers that want
to convert incoming sysfs values per standard hwmon practice, though the
macro itself can be used by anyone.

Signed-off-by: Darrick J. Wong <djwong@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
15 years agolib: proportions.c trivial sparse lock annotation
Harvey Harrison [Tue, 6 Jan 2009 22:40:50 +0000 (14:40 -0800)] 
lib: proportions.c trivial sparse lock annotation

Suppresses sparse warning:
lib/proportions.c:159:16: warning: context imbalance in 'prop_get_global': wrong count at exit
lib/proportions.c:159:16:    context 'RCU': wanted 0, got 1
lib/proportions.c:164:2: warning: context imbalance in 'prop_put_global': unexpected unlock
lib/proportions.c:164:2:    context 'RCU': wanted 0, got -1

Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
15 years agolib: radix_tree.c make percpu variable static
Harvey Harrison [Tue, 6 Jan 2009 22:40:50 +0000 (14:40 -0800)] 
lib: radix_tree.c make percpu variable static

radix_tree_preloads is unused outside of this file, make it static.

Noticed by sparse:
lib/radix-tree.c:84:1: warning: symbol 'per_cpu__radix_tree_preloads' was not declared. Should it be static?

Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
15 years agolib: fix sparse shadowed variable warning
Harvey Harrison [Tue, 6 Jan 2009 22:40:49 +0000 (14:40 -0800)] 
lib: fix sparse shadowed variable warning

pos is always set before being used, no need to declare a
second one inside the if() block.

lib/prio_heap.c:34:7: warning: symbol 'pos' shadows an earlier one
lib/prio_heap.c:30:6: originally declared here

Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
15 years agofork.c: cleanup for copy_sighand()
Zhaolei [Tue, 6 Jan 2009 22:40:46 +0000 (14:40 -0800)] 
fork.c: cleanup for copy_sighand()

Check CLONE_SIGHAND only is enough, because combination of CLONE_THREAD and
CLONE_SIGHAND is already done in copy_process().

Impact: cleanup, no functionality changed

Signed-off-by: Zhao Lei <zhaolei@cn.fujitsu.com>
Cc: Roland McGrath <roland@redhat.com>
Cc: Oleg Nesterov <oleg@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
15 years agoRemove remaining unwinder code
Alexey Dobriyan [Tue, 6 Jan 2009 22:40:45 +0000 (14:40 -0800)] 
Remove remaining unwinder code

Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Cc: Gabor Gombas <gombasg@sztaki.hu>
Cc: Jan Beulich <jbeulich@novell.com>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: Ingo Molnar <mingo@elte.hu>,
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
15 years agofs/exec.c:__bprm_mm_init(): clean up error handling
Luiz Fernando N. Capitulino [Tue, 6 Jan 2009 22:40:44 +0000 (14:40 -0800)] 
fs/exec.c:__bprm_mm_init(): clean up error handling

Untangle the error unwinding in this function, saving a test of local
variable `vma'.

Signed-off-by: Luiz Fernando N. Capitulino <lcapitulino@mandriva.com.br>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
15 years agodo_mounts: add device info to mount message
Marton Balint [Tue, 6 Jan 2009 22:40:43 +0000 (14:40 -0800)] 
do_mounts: add device info to mount message

In the past, I used the root=...  command line parameter to specify the
root filesystem to the kernel.  Now it seems that specifying it is not
necessary.  The kernel detects the root filesystem even if the kernel
command line is empty.  My root fs is on a raid1 device by the way, and I
am not using initrd for the boot process.

If the kernel detects the root filesystem somehow, I think it should print
out the result of this detection, otherwise I will not know which device
has the root filesystem.  Or is there an easy way to get this information
on a running system?  I had a quick look at the /proc and /sys
filesystems, but haven't found anything useful there.

Signed-off-by: Marton Balint <cus@fazekas.hu>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
15 years agooops handling: ensure that any oops is flushed to the mtdoops console
Viktor Rosendahl [Tue, 6 Jan 2009 22:40:42 +0000 (14:40 -0800)] 
oops handling: ensure that any oops is flushed to the mtdoops console

This used to work unpatched with older kernels, during the development
phase of mtdoops.  Before commit e3e8a75d2acfc61ebf25524666a0a2c6abb0620c
a space was printed with console_loglevel set to 15, which probably
flushed the oops message as a side effect.

This is another patch from the Nokia N810 kernel.

Signed-off-by: Viktor Rosendahl <viktor.rosendahl@nokia.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
15 years agoCheck fops_get() return value
Laurent Pinchart [Tue, 6 Jan 2009 22:40:40 +0000 (14:40 -0800)] 
Check fops_get() return value

Several subsystem open handlers dereference the fops_get() return value
without checking it for nullness.  This opens a race condition between the
open handler and module unloading.

A module can be marked as being unloaded (MODULE_STATE_GOING) before its
exit function is called and gets the chance to unregister the driver.
During that window open handlers can still be called, and fops_get() will
fail in try_module_get() and return a NULL pointer.

This change checks the fops_get() return value and returns -ENODEV if NULL.

Reported-by: Alan Jenkins <alan-jenkins@tuffmail.co.uk>
Signed-off-by: Laurent Pinchart <laurent.pinchart@skynet.be>
Acked-by: Takashi Iwai <tiwai@suse.de>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Dave Airlie <airlied@linux.ie>
Acked-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
15 years agopci: use pci_ioremap_bar() in drivers/misc
Arjan van de Ven [Tue, 6 Jan 2009 22:40:39 +0000 (14:40 -0800)] 
pci: use pci_ioremap_bar() in drivers/misc

Use the newly introduced pci_ioremap_bar() function in drivers/misc.
pci_ioremap_bar() just takes a pci device and a bar number, with the goal
of making it really hard to get wrong, while also having a central place
to stick sanity checks.

Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
15 years agoatomic_t: unify all arch definitions
Matthew Wilcox [Tue, 6 Jan 2009 22:40:39 +0000 (14:40 -0800)] 
atomic_t: unify all arch definitions

The atomic_t type cannot currently be used in some header files because it
would create an include loop with asm/atomic.h.  Move the type definition
to linux/types.h to break the loop.

Signed-off-by: Matthew Wilcox <willy@linux.intel.com>
Cc: Huang Ying <ying.huang@intel.com>
Cc: <linux-arch@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
15 years agoinit: properly placing noinline keyword
Rakib Mullick [Tue, 6 Jan 2009 22:40:38 +0000 (14:40 -0800)] 
init: properly placing noinline keyword

checkpatch warns about 'static void noinline'.  It wants `static noinline
void'.

Both are permissible, but the kernel consistently uses `static inline' and
`static noinline', and consistency is good.  Hence let's keep the
checkpatch warning and fix up this code site.

[akpm@linux-foundation.org: rewrote changelog]
Signed-off-by: Md.Rakib H. Mullick <rakib.mullick@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
15 years agomm: hugetlb: remove redundant `if' operation
Cyrill Gorcunov [Tue, 6 Jan 2009 22:40:33 +0000 (14:40 -0800)] 
mm: hugetlb: remove redundant `if' operation

At this point we already know that 'addr' is not NULL so get rid of
redundant 'if'.  Probably gcc eliminate it by optimization pass.

[akpm@linux-foundation.org: use __weak, too]
Signed-off-by: Cyrill Gorcunov <gorcunov@openvz.org>
Reviewed-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
15 years agomm: stop kswapd's infinite loop at high order allocation
KOSAKI Motohiro [Tue, 6 Jan 2009 22:40:33 +0000 (14:40 -0800)] 
mm: stop kswapd's infinite loop at high order allocation

Wassim Dagash reported following kswapd infinite loop problem.

  kswapd runs in some infinite loop trying to swap until order 10 of zone
  highmem is OK.... kswapd will continue to try to balance order 10 of zone
  highmem forever (or until someone release a very large chunk of highmem).

For non order-0 allocations, the system may never be balanced due to
fragmentation but kswapd should not infinitely loop as a result.

Instead, recheck all watermarks at order-0 as they are the most important.
If watermarks are ok, kswapd will go back to sleep.

[akpm@linux-foundation.org: fix comment]
Reported-by: wassim dagash <wassim.dagash@gmail.com>
Signed-off-by: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Reviewed-by: Nick Piggin <npiggin@suse.de>
Signed-off-by: Mel Gorman <mel@csn.ul.ie>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
15 years agobootmem: print request details before BUG_ON(them)
Johannes Weiner [Tue, 6 Jan 2009 22:40:32 +0000 (14:40 -0800)] 
bootmem: print request details before BUG_ON(them)

Moving the request details print-out before the sanity checks that
might panic() enables us to analyse invalid requests without having
access to the line information of the stack dump.

Signed-off-by: Johannes Weiner <hannes@cmpxchg.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
15 years agomm: check for no mmaps in exit_mmap()
Johannes Weiner [Tue, 6 Jan 2009 22:40:31 +0000 (14:40 -0800)] 
mm: check for no mmaps in exit_mmap()

When dup_mmap() ooms we can end up with mm->mmap == NULL.  The error
path does mmput() and unmap_vmas() gets a NULL vma which it
dereferences.

In exit_mmap() there is nothing to do at all for this case, we can
cancel the callpath right there.

[akpm@linux-foundation.org: add sorely-needed comment]
Signed-off-by: Johannes Weiner <hannes@cmpxchg.org>
Reported-by: Akinobu Mita <akinobu.mita@gmail.com>
Cc: Nick Piggin <nickpiggin@yahoo.com.au>
Cc: Hugh Dickins <hugh@veritas.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
15 years agomm: kill page_queue_congested()
KOSAKI Motohiro [Tue, 6 Jan 2009 22:40:30 +0000 (14:40 -0800)] 
mm: kill page_queue_congested()

page_queue_congested() was introduced in 2002, but it was never used

Signed-off-by: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
15 years agomm: remove CONFIG_OUT_OF_LINE_PFN_TO_PAGE
KOSAKI Motohiro [Tue, 6 Jan 2009 22:40:29 +0000 (14:40 -0800)] 
mm: remove CONFIG_OUT_OF_LINE_PFN_TO_PAGE

No architectures use CONFIG_OUT_OF_LINE_PFN_TO_PAGE - it can be removed.

Signed-off-by: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Cc: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
15 years agomm: introduce get_mm_hiwater_xxx(), fix taskstats->hiwater_xxx accounting
Oleg Nesterov [Tue, 6 Jan 2009 22:40:29 +0000 (14:40 -0800)] 
mm: introduce get_mm_hiwater_xxx(), fix taskstats->hiwater_xxx accounting

xacct_add_tsk() relies on do_exit()->update_hiwater_xxx() and uses
mm->hiwater_xxx directly, this leads to 2 problems:

- taskstats_user_cmd() can call fill_pid()->xacct_add_tsk() at any
  moment before the task exits, so we should check the current values of
  rss/vm anyway.

- do_exit()->update_hiwater_xxx() calls are racy.  An exiting thread can
  be preempted right before mm->hiwater_xxx = new_val, and another thread
  can use A_LOT of memory and exit in between.  When the first thread
  resumes it can be the last thread in the thread group, in that case we
  report the wrong hiwater_xxx values which do not take A_LOT into
  account.

Introduce get_mm_hiwater_rss() and get_mm_hiwater_vm() helpers and change
xacct_add_tsk() to use them.  The first helper will also be used by
rusage->ru_maxrss accounting.

Kill do_exit()->update_hiwater_xxx() calls.  Unless we are going to
decrease rss/vm there is no point to update mm->hiwater_xxx, and nobody
can look at this mm_struct when exit_mmap() actually unmaps the memory.

Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Acked-by: Hugh Dickins <hugh@veritas.com>
Reviewed-by: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Acked-by: Balbir Singh <balbir@linux.vnet.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
15 years agomm: pagecache gfp flags fix
Nick Piggin [Tue, 6 Jan 2009 22:40:28 +0000 (14:40 -0800)] 
mm: pagecache gfp flags fix

Frustratingly, gfp_t is really divided into two classes of flags.  One are
the context dependent ones (can we sleep?  can we enter filesystem?  block
subsystem?  should we use some extra reserves, etc.).  The other ones are
the type of memory required and depend on how the algorithm is implemented
rather than the point at which the memory is allocated (highmem?  dma
memory?  etc).

Some of the functions which allocate a page and add it to page cache take
a gfp_t, but sometimes those functions or their callers aren't really
doing the right thing: when allocating pagecache page, the memory type
should be mapping_gfp_mask(mapping).  When allocating radix tree nodes,
the memory type should be kernel mapped (not highmem) memory.  The gfp_t
argument should only really be needed for context dependent options.

This patch doesn't really solve that tangle in a nice way, but it does
attempt to fix a couple of bugs.

- find_or_create_page changes its radix-tree allocation to only include
  the main context dependent flags in order so the pagecache page may be
  allocated from arbitrary types of memory without affecting the
  radix-tree.  In practice, slab allocations don't come from highmem
  anyway, and radix-tree only uses slab allocations.  So there isn't a
  practical change (unless some fs uses GFP_DMA for pages).

- grab_cache_page_nowait() is changed to allocate radix-tree nodes with
  GFP_NOFS, because it is not supposed to reenter the filesystem.  This
  bug could cause lock recursion if a filesystem is not expecting the
  function to reenter the fs (as-per documentation).

Filesystems should be careful about exactly what semantics they want and
what they get when fiddling with gfp_t masks to allocate pagecache.  One
should be as liberal as possible with the type of memory that can be used,
and same for the the context specific flags.

Signed-off-by: Nick Piggin <npiggin@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
15 years agofs: sys_sync fix
Nick Piggin [Tue, 6 Jan 2009 22:40:26 +0000 (14:40 -0800)] 
fs: sys_sync fix

s_syncing livelock avoidance was breaking data integrity guarantee of
sys_sync, by allowing sys_sync to skip writing or waiting for superblocks
if there is a concurrent sys_sync happening.

This livelock avoidance is much less important now that we don't have the
get_super_to_sync() call after every sb that we sync.  This was replaced
by __put_super_and_need_restart.

Signed-off-by: Nick Piggin <npiggin@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
15 years agofs: sync_sb_inodes fix
Nick Piggin [Tue, 6 Jan 2009 22:40:25 +0000 (14:40 -0800)] 
fs: sync_sb_inodes fix

Fix data integrity semantics required by sys_sync, by iterating over all
inodes and waiting for any writeback pages after the initial writeout.
Comments explain the exact problem.

Signed-off-by: Nick Piggin <npiggin@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
15 years agofs: remove WB_SYNC_HOLD
Nick Piggin [Tue, 6 Jan 2009 22:40:25 +0000 (14:40 -0800)] 
fs: remove WB_SYNC_HOLD

Remove WB_SYNC_HOLD.  The primary motiviation is the design of my
anti-starvation code for fsync.  It requires taking an inode lock over the
sync operation, so we could run into lock ordering problems with multiple
inodes.  It is possible to take a single global lock to solve the ordering
problem, but then that would prevent a future nice implementation of "sync
multiple inodes" based on lock order via inode address.

Seems like a backward step to remove this, but actually it is busted
anyway: we can't use the inode lists for data integrity wait: an inode can
be taken off the dirty lists but still be under writeback.  In order to
satisfy data integrity semantics, we should wait for it to finish
writeback, but if we only search the dirty lists, we'll miss it.

It would be possible to have a "writeback" list, for sys_sync, I suppose.
But why complicate things by prematurely optimise?  For unmounting, we
could avoid the "livelock avoidance" code, which would be easier, but
again premature IMO.

Fixing the existing data integrity problem will come next.

Signed-off-by: Nick Piggin <npiggin@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
15 years agoUBIFS: do not use WB_SYNC_HOLD
Artem Bityutskiy [Tue, 6 Jan 2009 22:40:23 +0000 (14:40 -0800)] 
UBIFS: do not use WB_SYNC_HOLD

WB_SYNC_HOLD is going to be zapped so we should not use it. Use
%WB_SYNC_NONE instead. Here is what akpm said:

"I think I'll just switch that to WB_SYNC_NONE.  The `wait==0' mode is
just an advisory thing to help the fs shove lots of data into the
queues.  If some gets missed then it'll be picked up on the second
->sync_fs call, with wait==1."

Thanks to Randy Dunlap for catching this.

Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Cc: Nick Piggin <npiggin@suse.de>
Cc: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
15 years agomm: direct IO starvation improvement
Nick Piggin [Tue, 6 Jan 2009 22:40:22 +0000 (14:40 -0800)] 
mm: direct IO starvation improvement

Direct IO can invalidate and sync a lot of pagecache pages in the mapping.
 A 4K direct IO will actually try to sync and/or invalidate the pagecache
of the entire file, for example (which might be many GB or TB large).

Improve this by doing range syncs.  Also, memory no longer has to be
unmapped to catch the dirty bits for syncing, as dirty bits would remain
coherent due to dirty mmap accounting.

This fixes the immediate DM deadlocks when doing direct IO reads to block
device with a mounted filesystem, if only by papering over the problem
somewhat rather than addressing the fsync starvation cases.

Signed-off-by: Nick Piggin <npiggin@suse.de>
Reviewed-by: Jeff Moyer <jmoyer@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
15 years agomm/mmap.c: fix coding style
ZhenwenXu [Tue, 6 Jan 2009 22:40:21 +0000 (14:40 -0800)] 
mm/mmap.c: fix coding style

Fix a little of the coding style in mm/mmap.c

[akpm@linux-foundation.org: cleanup]
Signed-off-by: ZhenwenXu <helight.xu@gmail.com>
Signed-off-by: Hugh Dickins <hugh@veritas.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
15 years agoshmem: unify regular and tiny shmem
Matt Mackall [Tue, 6 Jan 2009 22:40:20 +0000 (14:40 -0800)] 
shmem: unify regular and tiny shmem

tiny-shmem shares most of its 130 lines of code with shmem and tends to
break when particular bits of shmem get modified.  Unifying saves code and
makes keeping these two in sync much easier.

before:
  14367     392      24   14783    39bf mm/shmem.o
    396      72       8     476     1dc mm/tiny-shmem.o

after:
  14367     392      24   14783    39bf mm/shmem.o
    412      72       8     492     1ec mm/shmem.o tiny

Signed-off-by: Matt Mackall <mpm@selenic.com>
Acked-by: Hugh Dickins <hugh@veritas.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
15 years agoblock_write_begin(): remove useless goto
Franck Bui-Huu [Tue, 6 Jan 2009 22:40:19 +0000 (14:40 -0800)] 
block_write_begin(): remove useless goto

Signed-off-by: Franck Bui-Huu <fbuihuu@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
15 years agomm: make get_user_pages() interruptible
Ying Han [Tue, 6 Jan 2009 22:40:18 +0000 (14:40 -0800)] 
mm: make get_user_pages() interruptible

The initial implementation of checking TIF_MEMDIE covers the cases of OOM
killing.  If the process has been OOM killed, the TIF_MEMDIE is set and it
return immediately.  This patch includes:

1.  add the case that the SIGKILL is sent by user processes.  The
   process can try to get_user_pages() unlimited memory even if a user
   process has sent a SIGKILL to it(maybe a monitor find the process
   exceed its memory limit and try to kill it).  In the old
   implementation, the SIGKILL won't be handled until the get_user_pages()
   returns.

2.  change the return value to be ERESTARTSYS.  It makes no sense to
   return ENOMEM if the get_user_pages returned by getting a SIGKILL
   signal.  Considering the general convention for a system call
   interrupted by a signal is ERESTARTNOSYS, so the current return value
   is consistant to that.

Lee:

An unfortunate side effect of "make-get_user_pages-interruptible" is that
it prevents a SIGKILL'd task from munlock-ing pages that it had mlocked,
resulting in freeing of mlocked pages.  Freeing of mlocked pages, in
itself, is not so bad.  We just count them now--altho' I had hoped to
remove this stat and add PG_MLOCKED to the free pages flags check.

However, consider pages in shared libraries mapped by more than one task
that a task mlocked--e.g., via mlockall().  If the task that mlocked the
pages exits via SIGKILL, these pages would be left mlocked and
unevictable.

Proposed fix:

Add another GUP flag to ignore sigkill when calling get_user_pages from
munlock()--similar to Kosaki Motohiro's 'IGNORE_VMA_PERMISSIONS flag for
the same purpose.  We are not actually allocating memory in this case,
which "make-get_user_pages-interruptible" intends to avoid.  We're just
munlocking pages that are already resident and mapped, and we're reusing
get_user_pages() to access those pages.

??  Maybe we should combine 'IGNORE_VMA_PERMISSIONS and '_IGNORE_SIGKILL
into a single flag: GUP_FLAGS_MUNLOCK ???

[Lee.Schermerhorn@hp.com: ignore sigkill in get_user_pages during munlock]
Signed-off-by: Paul Menage <menage@google.com>
Signed-off-by: Ying Han <yinghan@google.com>
Reviewed-by: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Reviewed-by: Pekka Enberg <penberg@cs.helsinki.fi>
Cc: Nick Piggin <nickpiggin@yahoo.com.au>
Cc: Hugh Dickins <hugh@veritas.com>
Cc: Oleg Nesterov <oleg@tv-sign.ru>
Cc: Lee Schermerhorn <lee.schermerhorn@hp.com>
Cc: Rohit Seth <rohitseth@google.com>
Cc: David Rientjes <rientjes@google.com>
Signed-off-by: Lee Schermerhorn <lee.schermerhorn@hp.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
15 years agohugetlb: unsigned ret cannot be negative
Roel Kluin [Tue, 6 Jan 2009 22:40:14 +0000 (14:40 -0800)] 
hugetlb: unsigned ret cannot be negative

unsigned long ret cannot be negative, but ret can get -EFAULT.

Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Cc: Hugh Dickins <hugh@veritas.com>
Cc: Christoph Lameter <clameter@sgi.com>
Cc: Adam Litke <agl@us.ibm.com>
Cc: David Gibson <david@gibson.dropbear.id.au>
Cc: Ken Chen <kenchen@google.com>
Cc: Nick Piggin <npiggin@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
15 years agovmscan: shrink_active_list(): reduce lru_lock hold time
Andrew Morton [Tue, 6 Jan 2009 22:40:13 +0000 (14:40 -0800)] 
vmscan: shrink_active_list(): reduce lru_lock hold time

These three statements manipulate local variables and do not need the lock
coverage.

Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: Lee Schermerhorn <Lee.Schermerhorn@hp.com>
Cc: Rik van Riel <riel@redhat.com
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
15 years agobadpage: KERN_ALERT BUG instead of KERN_EMERG
Hugh Dickins [Tue, 6 Jan 2009 22:40:13 +0000 (14:40 -0800)] 
badpage: KERN_ALERT BUG instead of KERN_EMERG

bad_page() and rmap Eeek messages have said KERN_EMERG for a few years,
which I've followed in print_bad_pte().  These are serious system errors,
on a par with BUGs, but they're not quite emergencies, and we do our best
to carry on: say KERN_ALERT "BUG: " like the x86 oops does.

And remove the "Trying to fix it up, but a reboot is needed" line: it's
not untrue, but I hope the KERN_ALERT "BUG: " conveys as much.

Signed-off-by: Hugh Dickins <hugh@veritas.com>
Cc: Nick Piggin <nickpiggin@yahoo.com.au>
Cc: Christoph Lameter <cl@linux-foundation.org>
Cc: Mel Gorman <mel@csn.ul.ie>
Cc: Rik van Riel <riel@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
15 years agobadpage: ratelimit print_bad_pte and bad_page
Hugh Dickins [Tue, 6 Jan 2009 22:40:12 +0000 (14:40 -0800)] 
badpage: ratelimit print_bad_pte and bad_page

print_bad_pte() and bad_page() might each need ratelimiting - especially
for their dump_stacks, almost never of interest, yet not quite
dispensible.  Correlating corruption across neighbouring entries can be
very helpful, so allow a burst of 60 reports before keeping quiet for the
remainder of that minute (or allow a steady drip of one report per
second).

Signed-off-by: Hugh Dickins <hugh@veritas.com>
Cc: Nick Piggin <nickpiggin@yahoo.com.au>
Cc: Christoph Lameter <cl@linux-foundation.org>
Cc: Mel Gorman <mel@csn.ul.ie>
Cc: Rik van Riel <riel@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
15 years agobadpage: remove vma from page_remove_rmap
Hugh Dickins [Tue, 6 Jan 2009 22:40:11 +0000 (14:40 -0800)] 
badpage: remove vma from page_remove_rmap

Remove page_remove_rmap()'s vma arg, which was only for the Eeek message.
And remove the BUG_ON(page_mapcount(page) == 0) from CONFIG_DEBUG_VM's
page_dup_rmap(): we're trying to be more resilient about that than BUGs.

Signed-off-by: Hugh Dickins <hugh@veritas.com>
Cc: Nick Piggin <nickpiggin@yahoo.com.au>
Cc: Christoph Lameter <cl@linux-foundation.org>
Cc: Mel Gorman <mel@csn.ul.ie>
Cc: Rik van Riel <riel@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
15 years agobadpage: zap print_bad_pte on swap and file
Hugh Dickins [Tue, 6 Jan 2009 22:40:10 +0000 (14:40 -0800)] 
badpage: zap print_bad_pte on swap and file

Complete zap_pte_range()'s coverage of bad pagetable entries by calling
print_bad_pte() on a pte_file in a linear vma and on a bad swap entry.
That needs free_swap_and_cache() to tell it, which will also have shown
one of those "swap_free" errors (but with much less information).

Similar checks in fork's copy_one_pte()?  No, that would be more noisy
than helpful: we'll see them when parent and child exec or exit.

Where do_nonlinear_fault() calls print_bad_pte(): omit !VM_CAN_NONLINEAR
case, that could only be a bug in sys_remap_file_pages(), not a bad pte.
VM_FAULT_OOM rather than VM_FAULT_SIGBUS?  Well, okay, that is consistent
with what happens if do_swap_page() operates a bad swap entry; but don't
we have patches to be more careful about killing when VM_FAULT_OOM?

Signed-off-by: Hugh Dickins <hugh@veritas.com>
Cc: Nick Piggin <nickpiggin@yahoo.com.au>
Cc: Christoph Lameter <cl@linux-foundation.org>
Cc: Mel Gorman <mel@csn.ul.ie>
Cc: Rik van Riel <riel@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
15 years agobadpage: vm_normal_page use print_bad_pte
Hugh Dickins [Tue, 6 Jan 2009 22:40:09 +0000 (14:40 -0800)] 
badpage: vm_normal_page use print_bad_pte

print_bad_pte() is so far being called only when zap_pte_range() finds
negative page_mapcount, or there's a fault on a pte_file where it does not
belong.  That's weak coverage when we suspect pagetable corruption.

Originally, it was called when vm_normal_page() found an invalid pfn: but
pfn_valid is expensive on some architectures and configurations, so 2.6.24
put that under CONFIG_DEBUG_VM (which doesn't help in the field), then
2.6.26 replaced it by a VM_BUG_ON (likewise).

Reinstate the print_bad_pte() in vm_normal_page(), but use a cheaper test
than pfn_valid(): memmap_init_zone() (used in bootup and hotplug) keep a
__read_mostly note of the highest_memmap_pfn, vm_normal_page() then check
pfn against that.  We could call this pfn_plausible() or pfn_sane(), but I
doubt we'll need it elsewhere: of course it's not reliable, but gives much
stronger pagetable validation on many boxes.

Also use print_bad_pte() when the pte_special bit is found outside a
VM_PFNMAP or VM_MIXEDMAP area, instead of VM_BUG_ON.

Signed-off-by: Hugh Dickins <hugh@veritas.com>
Cc: Nick Piggin <nickpiggin@yahoo.com.au>
Cc: Christoph Lameter <cl@linux-foundation.org>
Cc: Mel Gorman <mel@csn.ul.ie>
Cc: Rik van Riel <riel@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
15 years agobadpage: replace page_remove_rmap Eeek and BUG
Hugh Dickins [Tue, 6 Jan 2009 22:40:08 +0000 (14:40 -0800)] 
badpage: replace page_remove_rmap Eeek and BUG

Now that bad pages are kept out of circulation, there is no need for the
infamous page_remove_rmap() BUG() - once that page is freed, its negative
mapcount will issue a "Bad page state" message and the page won't be
freed.  Removing the BUG() allows more info, on subsequent pages, to be
gathered.

We do have more info about the page at this point than bad_page() can know
- notably, what the pmd is, which might pinpoint something like low 64kB
corruption - but page_remove_rmap() isn't given the address to find that.

In practice, there is only one call to page_remove_rmap() which has ever
reported anything, that from zap_pte_range() (usually on exit, sometimes
on munmap).  It has all the info, so remove page_remove_rmap()'s "Eeek"
message and leave it all to zap_pte_range().

mm/memory.c already has a hardly used print_bad_pte() function, showing
some of the appropriate info: extend it to show what we want for the rmap
case: pte info, page info (when there is a page) and vma info to compare.
zap_pte_range() already knows the pmd, but print_bad_pte() is easier to
use if it works that out for itself.

Some of this info is also shown in bad_page()'s "Bad page state" message.
Keep them separate, but adjust them to match each other as far as
possible.  Say "Bad page map" in print_bad_pte(), and add a TAINT_BAD_PAGE
there too.

print_bad_pte() show current->comm unconditionally (though it should get
repeated in the usually irrelevant stack trace): sorry, I misled Nick
Piggin to make it conditional on vm_mm == current->mm, but current->mm is
already NULL in the exit case.  Usually current->comm is good, though
exceptionally it may not be that of the mm (when "swapoff" for example).

Signed-off-by: Hugh Dickins <hugh@veritas.com>
Cc: Nick Piggin <nickpiggin@yahoo.com.au>
Cc: Christoph Lameter <cl@linux-foundation.org>
Cc: Mel Gorman <mel@csn.ul.ie>
Cc: Rik van Riel <riel@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
15 years agobadpage: keep any bad page out of circulation
Hugh Dickins [Tue, 6 Jan 2009 22:40:06 +0000 (14:40 -0800)] 
badpage: keep any bad page out of circulation

Until now the bad_page() checkers have special-cased PageReserved, keeping
those pages out of circulation thereafter.  Now extend the special case to
all: we want to keep ANY page with bad state out of circulation - the
"free" page may well be in use by something.

Leave the bad state of those pages untouched, for examination by
debuggers; except for PageBuddy - leaving that set would risk bringing the
page back.

Signed-off-by: Hugh Dickins <hugh@veritas.com>
Cc: Nick Piggin <nickpiggin@yahoo.com.au>
Cc: Christoph Lameter <cl@linux-foundation.org>
Cc: Mel Gorman <mel@csn.ul.ie>
Cc: Rik van Riel <riel@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
15 years agobadpage: simplify page_alloc flag check+clear
Hugh Dickins [Tue, 6 Jan 2009 22:40:05 +0000 (14:40 -0800)] 
badpage: simplify page_alloc flag check+clear

Simplify the PAGE_FLAGS checking and clearing when freeing and allocating
a page: check the same flags as before when freeing, clear ALL the flags
(unless PageReserved) when freeing, check ALL flags off when allocating.

Signed-off-by: Hugh Dickins <hugh@veritas.com>
Cc: Nick Piggin <nickpiggin@yahoo.com.au>
Cc: Christoph Lameter <cl@linux-foundation.org>
Cc: Mel Gorman <mel@csn.ul.ie>
Cc: Rik van Riel <riel@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
15 years agofs: truncate blocks outside i_size after O_DIRECT write error
Dmitri Monakhov [Tue, 6 Jan 2009 22:40:04 +0000 (14:40 -0800)] 
fs: truncate blocks outside i_size after O_DIRECT write error

In case of error extending write may have instantiated a few blocks
outside i_size.  We need to trim these blocks.  We have to do it
*regardless* to blocksize.  At least ext2, ext3 and reiserfs interpret
(i_size < biggest block) condition as error.  Fsck will complain about
wrong i_size.  Then fsck will fix the error by changing i_size according
to the biggest block.  This is bad because this blocks contain garbage
from previous write attempt.  And result in data corruption.

####TESTCASE_BEGIN
$touch /mnt/test/BIG_FILE
## at this moment /mnt/test/BIG_FILE size and blocks equal to zero
open("/mnt/test/BIG_FILE", O_WRONLY|O_CREAT|O_DIRECT, 0666) = 3
write(3, "aaaaaaaaaaaa"..., 104857600) = -1 ENOSPC (No space left on device)
## size and block sould't be changed because write op failed.
$stat /mnt/test/BIG_FILE
File: `/mnt/test/BIG_FILE'
Size: 0 Blocks: 110896 IO Block: 1024 regular empty file
<<<<<<<<^^^^^^^^^^^^^^^^^^^^^^^^^^^^^file size is less than biggest block idx
Device: fe07h/65031d Inode: 14 Links: 1
Access: (0644/-rw-r--r--) Uid: ( 0/ root) Gid: ( 0/ root)
Access: 2007-01-24 20:03:38.000000000 +0300
Modify: 2007-01-24 20:03:38.000000000 +0300
Change: 2007-01-24 20:03:39.000000000 +0300

#fsck.ext3 -f /dev/VG/test
e2fsck 1.39 (29-May-2006)
Pass 1: Checking inodes, blocks, and sizes
Inode 14, i_size is 0, should be 56556544. Fix<y>? yes
Pass 2: Checking directory structure
....
#####TESTCASE_ENDdiff --git a/fs/direct-io.c b/fs/direct-io.c
index af0558d..4e88bea 100644

[akpm@linux-foundation.org: use i_size_read()]
Signed-off-by: Dmitri Monakhov <dmonakhov@openvz.org>
Cc: Zach Brown <zach.brown@oracle.com>
Cc: Nick Piggin <npiggin@suse.de>
Cc: Badari Pulavarty <pbadari@us.ibm.com>
Cc: Chris Mason <chris.mason@oracle.com>
Cc: Dave Chinner <david@fromorbit.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
15 years agomm: kill zone_is_near_oom()
KOSAKI Motohiro [Tue, 6 Jan 2009 22:40:03 +0000 (14:40 -0800)] 
mm: kill zone_is_near_oom()

zone_is_near_oom() is unused.

Signed-off-by: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
15 years agovmscan: improve reclaim throughput to bail out patch
KOSAKI Motohiro [Tue, 6 Jan 2009 22:40:02 +0000 (14:40 -0800)] 
vmscan: improve reclaim throughput to bail out patch

The vmscan bail out patch move nr_reclaimed variable to struct
scan_control.  Unfortunately, indirect access can easily happen cache
miss.

if heavy memory pressure happend, that's ok.
cache miss already plenty. it is not observable.

but, if memory pressure is lite, performance degression is obserbable.

I compared following three pattern (it was mesured 10 times each)

hackbench 125 process 3000
hackbench 130 process 3000
hackbench 135 process 3000

            2.6.28-rc6                       bail-out

125 130 135 125 130 135
      ==============================================================
71.866 75.86 81.274 93.414 73.254 193.382
74.145 78.295 77.27 74.897 75.021 80.17
70.305 77.643 75.855 70.134 77.571 79.896
74.288 73.986 75.955 77.222 78.48 80.619
72.029 79.947 78.312 75.128 82.172 79.708
71.499 77.615 77.042 74.177 76.532 77.306
76.188 74.471 83.562 73.839 72.43 79.833
73.236 75.606 78.743 76.001 76.557 82.726
69.427 77.271 76.691 76.236 79.371 103.189
72.473 76.978 80.643 69.128 78.932 75.736

avg 72.545 76.767 78.534 76.017 77.03 93.256
std 1.89 1.71 2.41 6.29 2.79 34.16
min 69.427 73.986 75.855 69.128 72.43 75.736
max 76.188 79.947 83.562 93.414 82.172 193.382

about 4-5% degression.

Then, this patch introduces a temporary local variable.

result:

            2.6.28-rc6                       this patch

num 125 130 135 125 130 135
      ==============================================================
71.866 75.86 81.274 67.302 68.269 77.161
74.145 78.295 77.27    72.616 72.712 79.06
70.305 77.643 75.855   72.475 75.712 77.735
74.288 73.986 75.955   69.229 73.062 78.814
72.029 79.947 78.312   71.551 74.392 78.564
71.499 77.615 77.042   69.227 74.31 78.837
76.188 74.471 83.562   70.759 75.256 76.6
73.236 75.606 78.743   69.966 76.001 78.464
69.427 77.271 76.691   69.068 75.218 80.321
72.473 76.978 80.643   72.057 77.151 79.068

avg 72.545 76.767 78.534  70.425 74.2083 78.462
std  1.89 1.71 2.41     1.66 2.34 1.00
min  69.427 73.986 75.855   67.302 68.269 76.6
max  76.188 79.947 83.562   72.616 77.151 80.321

OK. the degression is disappeared.

Signed-off-by: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Acked-by: Rik van Riel <riel@redhat.com>
Cc: Mel Gorman <mel@csn.ul.ie>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
15 years agovmscan: bail out of direct reclaim after swap_cluster_max pages
Rik van Riel [Tue, 6 Jan 2009 22:40:01 +0000 (14:40 -0800)] 
vmscan: bail out of direct reclaim after swap_cluster_max pages

When the VM is under pressure, it can happen that several direct reclaim
processes are in the pageout code simultaneously.  It also happens that
the reclaiming processes run into mostly referenced, mapped and dirty
pages in the first round.

This results in multiple direct reclaim processes having a lower
pageout priority, which corresponds to a higher target of pages to
scan.

This in turn can result in each direct reclaim process freeing
many pages.  Together, they can end up freeing way too many pages.

This kicks useful data out of memory (in some cases more than half
of all memory is swapped out).  It also impacts performance by
keeping tasks stuck in the pageout code for too long.

A 30% improvement in hackbench has been observed with this patch.

The fix is relatively simple: in shrink_zone() we can check how many
pages we have already freed, direct reclaim tasks break out of the
scanning loop if they have already freed enough pages and have reached
a lower priority level.

We do not break out of shrink_zone() when priority == DEF_PRIORITY,
to ensure that equal pressure is applied to every zone in the common
case.

However, in order to do this we do need to know how many pages we already
freed, so move nr_reclaimed into scan_control.

akpm: a historical interlude...

We tried this in 2004:

:commit e468e46a9bea3297011d5918663ce6d19094cf87
:Author: akpm <akpm>
:Date:   Thu Jun 24 15:53:52 2004 +0000
:
:[PATCH] vmscan.c: dont reclaim too many pages
:
:    The shrink_zone() logic can, under some circumstances, cause far too many
:    pages to be reclaimed.  Say, we're scanning at high priority and suddenly hit
:    a large number of reclaimable pages on the LRU.
:    Change things so we bale out when SWAP_CLUSTER_MAX pages have been reclaimed.

And we reverted it in 2006:

:commit 210fe530305ee50cd889fe9250168228b2994f32
:Author: Andrew Morton <akpm@osdl.org>
:Date:   Fri Jan 6 00:11:14 2006 -0800
:
:    [PATCH] vmscan: balancing fix
:
:    Revert a patch which went into 2.6.8-rc1.  The changelog for that patch was:
:
:      The shrink_zone() logic can, under some circumstances, cause far too many
:      pages to be reclaimed.  Say, we're scanning at high priority and suddenly
:      hit a large number of reclaimable pages on the LRU.
:
:      Change things so we bale out when SWAP_CLUSTER_MAX pages have been
:      reclaimed.
:
:    Problem is, this change caused significant imbalance in inter-zone scan
:    balancing by truncating scans of larger zones.
:
:    Suppose, for example, ZONE_HIGHMEM is 10x the size of ZONE_NORMAL.  The zone
:    balancing algorithm would require that if we're scanning 100 pages of
:    ZONE_HIGHMEM, we should scan 10 pages of ZONE_NORMAL.  But this logic will
:    cause the scanning of ZONE_HIGHMEM to bale out after only 32 pages are
:    reclaimed.  Thus effectively causing smaller zones to be scanned relatively
:    harder than large ones.
:
:    Now I need to remember what the workload was which caused me to write this
:    patch originally, then fix it up in a different way...

And we haven't demonstrated that whatever problem caused that reversion is
not being reintroduced by this change in 2008.

Signed-off-by: Rik van Riel <riel@redhat.com>
Cc: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
15 years agohugetlb: fix sparse warnings
Hannes Eder [Tue, 6 Jan 2009 22:39:58 +0000 (14:39 -0800)] 
hugetlb: fix sparse warnings

Fix the following sparse warnings:

  mm/hugetlb.c:375:3: warning: returning void-valued expression
  mm/hugetlb.c:408:3: warning: returning void-valued expression

Signed-off-by: Hannes Eder <hannes@hanneseder.net>
Acked-by: Nishanth Aravamudan <nacc@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
15 years agoswapfile: let others seed random
Hugh Dickins [Tue, 6 Jan 2009 22:39:57 +0000 (14:39 -0800)] 
swapfile: let others seed random

Remove the srandom32((u32)get_seconds()) from non-rotational swapon:
there's been a coincidental discussion of earlier randomization, assume
that goes ahead, let swapon be a client rather than stirring for itself.

Signed-off-by: Hugh Dickins <hugh@veritas.com>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Donjun Shin <djshin90@gmail.com>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Cc: Jens Axboe <jens.axboe@oracle.com>
Cc: Joern Engel <joern@logfs.org>
Cc: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: Matthew Wilcox <matthew@wil.cx>
Cc: Nick Piggin <nickpiggin@yahoo.com.au>
Cc: Tejun Heo <teheo@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
15 years agoswapfile: change discard pgoff_t to sector_t
Hugh Dickins [Tue, 6 Jan 2009 22:39:56 +0000 (14:39 -0800)] 
swapfile: change discard pgoff_t to sector_t

Change pgoff_t nr_blocks in discard_swap() and discard_swap_cluster() to
sector_t: given the constraints on swap offsets (in particular, the 5 bits
of swap type accommodated in the same unsigned long), pgoff_t was actually
safe as is, but it certainly looked worrying when shifted left.

[akpm@linux-foundation.org: fix shift overflow]
Signed-off-by: Hugh Dickins <hugh@veritas.com>
Cc: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: Nick Piggin <nickpiggin@yahoo.com.au>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Jens Axboe <jens.axboe@oracle.com>
Cc: Matthew Wilcox <matthew@wil.cx>
Cc: Joern Engel <joern@logfs.org>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Cc: Donjun Shin <djshin90@gmail.com>
Cc: Tejun Heo <teheo@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
15 years agoswapfile: swap allocation cycle if nonrot
Hugh Dickins [Tue, 6 Jan 2009 22:39:55 +0000 (14:39 -0800)] 
swapfile: swap allocation cycle if nonrot

Though attempting to find free clusters (Andrea), swap allocation has
always restarted its searches from the beginning of the swap area (sct),
to reduce seek times between swap pages, by not scattering them all over
the partition.

But on a solidstate swap device, seeks are cheap, and block remapping to
level the wear may be limited by zones: in that case it's better to cycle
around the whole partition.

Signed-off-by: Hugh Dickins <hugh@veritas.com>
Cc: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: Nick Piggin <nickpiggin@yahoo.com.au>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Jens Axboe <jens.axboe@oracle.com>
Cc: Matthew Wilcox <matthew@wil.cx>
Cc: Joern Engel <joern@logfs.org>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Cc: Donjun Shin <djshin90@gmail.com>
Cc: Tejun Heo <teheo@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
15 years agoswapfile: swapon randomize if nonrot
Hugh Dickins [Tue, 6 Jan 2009 22:39:54 +0000 (14:39 -0800)] 
swapfile: swapon randomize if nonrot

Swap allocation has always started from the beginning of the swap area;
but if we're dealing with a solidstate swap device which can only remap
blocks within limited zones, that would sooner wear out the first zone.

Therefore sys_swapon() test whether blk_queue is non-rotational, and if so
randomize the cluster_next starting position for allocation.

If blk_queue is nonrot, note SWP_SOLIDSTATE for later use, and report it
with an "SS" at the right end of the kernel's "Adding ...  swap" message
(so that if it's both nonrot and discardable, "SSD" will be shown there).
Perhaps something should be shown in /proc/swaps (swapon -s), but we have
to be more cautious before making any addition to that format.

Signed-off-by: Hugh Dickins <hugh@veritas.com>
Cc: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: Nick Piggin <nickpiggin@yahoo.com.au>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Jens Axboe <jens.axboe@oracle.com>
Cc: Matthew Wilcox <matthew@wil.cx>
Cc: Joern Engel <joern@logfs.org>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Cc: Donjun Shin <djshin90@gmail.com>
Cc: Tejun Heo <teheo@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
15 years agoswapfile: swap allocation use discard
Hugh Dickins [Tue, 6 Jan 2009 22:39:53 +0000 (14:39 -0800)] 
swapfile: swap allocation use discard

When scan_swap_map() finds a free cluster of swap pages to allocate,
discard the old contents of the cluster if the device supports discard.
But don't bother when swap is so fragmented that we allocate single pages.

Be careful about racing allocations made while we're scanning for a
cluster; and hold up allocations made while we're discarding.

Signed-off-by: Hugh Dickins <hugh@veritas.com>
Cc: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: Nick Piggin <nickpiggin@yahoo.com.au>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Jens Axboe <jens.axboe@oracle.com>
Cc: Matthew Wilcox <matthew@wil.cx>
Cc: Joern Engel <joern@logfs.org>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Cc: Donjun Shin <djshin90@gmail.com>
Cc: Tejun Heo <teheo@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
15 years agoswapfile: swapon use discard (trim)
Hugh Dickins [Tue, 6 Jan 2009 22:39:51 +0000 (14:39 -0800)] 
swapfile: swapon use discard (trim)

When adding swap, all the old data on swap can be forgotten: sys_swapon()
discard all but the header page of the swap partition (or every extent but
the header of the swap file), to give a solidstate swap device the
opportunity to optimize its wear-levelling.

If that succeeds, note SWP_DISCARDABLE for later use, and report it with a
"D" at the right end of the kernel's "Adding ...  swap" message.  Perhaps
something should be shown in /proc/swaps (swapon -s), but we have to be
more cautious before making any addition to that format.

Signed-off-by: Hugh Dickins <hugh@veritas.com>
Cc: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: Nick Piggin <nickpiggin@yahoo.com.au>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Jens Axboe <jens.axboe@oracle.com>
Cc: Matthew Wilcox <matthew@wil.cx>
Cc: Joern Engel <joern@logfs.org>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Cc: Donjun Shin <djshin90@gmail.com>
Cc: Tejun Heo <teheo@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>