git.oblomov.eu Git - linux-2.6/blob - drivers/ide/pci/serverworks.c

   1 /*
   2  * linux/drivers/ide/pci/serverworks.c          Version 0.8      25 Ebr 2003
   3  *
   4  * Copyright (C) 1998-2000 Michel Aubry
   5  * Copyright (C) 1998-2000 Andrzej Krzysztofowicz
   6  * Copyright (C) 1998-2000 Andre Hedrick <andre@linux-ide.org>
   7  * Portions copyright (c) 2001 Sun Microsystems
   8  *
   9  *
  10  * RCC/ServerWorks IDE driver for Linux
  11  *
  12  *   OSB4: `Open South Bridge' IDE Interface (fn 1)
  13  *         supports UDMA mode 2 (33 MB/s)
  14  *
  15  *   CSB5: `Champion South Bridge' IDE Interface (fn 1)
  16  *         all revisions support UDMA mode 4 (66 MB/s)
  17  *         revision A2.0 and up support UDMA mode 5 (100 MB/s)
  18  *
  19  *         *** The CSB5 does not provide ANY register ***
  20  *         *** to detect 80-conductor cable presence. ***
  21  *
  22  *   CSB6: `Champion South Bridge' IDE Interface (optional: third channel)
  23  *
  24  *   HT1000: AKA BCM5785 - Hypertransport Southbridge for Opteron systems. IDE
  25  *   controller same as the CSB6. Single channel ATA100 only.
  26  *
  27  * Documentation:
  28  *      Available under NDA only. Errata info very hard to get.
  29  *
  30  */
  31
  32 #include <linux/types.h>
  33 #include <linux/module.h>
  34 #include <linux/kernel.h>
  35 #include <linux/ioport.h>
  36 #include <linux/pci.h>
  37 #include <linux/hdreg.h>
  38 #include <linux/ide.h>
  39 #include <linux/init.h>
  40 #include <linux/delay.h>
  41
  42 #include <asm/io.h>
  43
  44 #define SVWKS_CSB5_REVISION_NEW 0x92 /* min PCI_REVISION_ID for UDMA5 (A2.0) */
  45 #define SVWKS_CSB6_REVISION     0xa0 /* min PCI_REVISION_ID for UDMA4 (A1.0) */
  46
  47 /* Seagate Barracuda ATA IV Family drives in UDMA mode 5
  48  * can overrun their FIFOs when used with the CSB5 */
  49 static const char *svwks_bad_ata100[] = {
  50         "ST320011A",
  51         "ST340016A",
  52         "ST360021A",
  53         "ST380021A",
  54         NULL
  55 };
  56
  57 static u8 svwks_revision = 0;
  58 static struct pci_dev *isa_dev;
  59
  60 static int check_in_drive_lists (ide_drive_t *drive, const char **list)
  61 {
  62         while (*list)
  63                 if (!strcmp(*list++, drive->id->model))
  64                         return 1;
  65         return 0;
  66 }
  67
  68 static u8 svwks_ratemask (ide_drive_t *drive)
  69 {
  70         struct pci_dev *dev     = HWIF(drive)->pci_dev;
  71         u8 mode = 0;
  72
  73         if (!svwks_revision)
  74                 pci_read_config_byte(dev, PCI_REVISION_ID, &svwks_revision);
  75
  76         if (dev->device == PCI_DEVICE_ID_SERVERWORKS_HT1000IDE)
  77                 return 2;
  78         if (dev->device == PCI_DEVICE_ID_SERVERWORKS_OSB4IDE) {
  79                 u32 reg = 0;
  80                 if (isa_dev)
  81                         pci_read_config_dword(isa_dev, 0x64, &reg);
  82
  83                 /*
  84                  *      Don't enable UDMA on disk devices for the moment
  85                  */
  86                 if(drive->media == ide_disk)
  87                         return 0;
  88                 /* Check the OSB4 DMA33 enable bit */
  89                 return ((reg & 0x00004000) == 0x00004000) ? 1 : 0;
  90         } else if (svwks_revision < SVWKS_CSB5_REVISION_NEW) {
  91                 return 1;
  92         } else if (svwks_revision >= SVWKS_CSB5_REVISION_NEW) {
  93                 u8 btr = 0;
  94                 pci_read_config_byte(dev, 0x5A, &btr);
  95                 mode = btr & 0x3;
  96                 if (!eighty_ninty_three(drive))
  97                         mode = min(mode, (u8)1);
  98                 /* If someone decides to do UDMA133 on CSB5 the same
  99                    issue will bite so be inclusive */
 100                 if (mode > 2 && check_in_drive_lists(drive, svwks_bad_ata100))
 101                         mode = 2;
 102         }
 103         if (((dev->device == PCI_DEVICE_ID_SERVERWORKS_CSB6IDE) ||
 104              (dev->device == PCI_DEVICE_ID_SERVERWORKS_CSB6IDE2)) &&
 105             (!(PCI_FUNC(dev->devfn) & 1)))
 106                 mode = 2;
 107         return mode;
 108 }
 109
 110 static u8 svwks_csb_check (struct pci_dev *dev)
 111 {
 112         switch (dev->device) {
 113                 case PCI_DEVICE_ID_SERVERWORKS_CSB5IDE:
 114                 case PCI_DEVICE_ID_SERVERWORKS_CSB6IDE:
 115                 case PCI_DEVICE_ID_SERVERWORKS_CSB6IDE2:
 116                 case PCI_DEVICE_ID_SERVERWORKS_HT1000IDE:
 117                         return 1;
 118                 default:
 119                         break;
 120         }
 121         return 0;
 122 }
 123 static int svwks_tune_chipset (ide_drive_t *drive, u8 xferspeed)
 124 {
 125         static const u8 udma_modes[]            = { 0x00, 0x01, 0x02, 0x03, 0x04, 0x05 };
 126         static const u8 dma_modes[]             = { 0x77, 0x21, 0x20 };
 127         static const u8 pio_modes[]             = { 0x5d, 0x47, 0x34, 0x22, 0x20 };
 128         static const u8 drive_pci[]             = { 0x41, 0x40, 0x43, 0x42 };
 129         static const u8 drive_pci2[]            = { 0x45, 0x44, 0x47, 0x46 };
 130
 131         ide_hwif_t *hwif        = HWIF(drive);
 132         struct pci_dev *dev     = hwif->pci_dev;
 133         u8 speed;
 134         u8 pio                  = ide_get_best_pio_mode(drive, 255, 5, NULL);
 135         u8 unit                 = (drive->select.b.unit & 0x01);
 136         u8 csb5                 = svwks_csb_check(dev);
 137         u8 ultra_enable         = 0, ultra_timing = 0;
 138         u8 dma_timing           = 0, pio_timing = 0;
 139         u16 csb5_pio            = 0;
 140
 141         if (xferspeed == 255)   /* PIO auto-tuning */
 142                 speed = XFER_PIO_0 + pio;
 143         else
 144                 speed = ide_rate_filter(svwks_ratemask(drive), xferspeed);
 145
 146         /* If we are about to put a disk into UDMA mode we screwed up.
 147            Our code assumes we never _ever_ do this on an OSB4 */
 148
 149         if(dev->device == PCI_DEVICE_ID_SERVERWORKS_OSB4 &&
 150                 drive->media == ide_disk && speed >= XFER_UDMA_0)
 151                         BUG();
 152
 153         pci_read_config_byte(dev, drive_pci[drive->dn], &pio_timing);
 154         pci_read_config_byte(dev, drive_pci2[drive->dn], &dma_timing);
 155         pci_read_config_byte(dev, (0x56|hwif->channel), &ultra_timing);
 156         pci_read_config_word(dev, 0x4A, &csb5_pio);
 157         pci_read_config_byte(dev, 0x54, &ultra_enable);
 158
 159         /* Per Specified Design by OEM, and ASIC Architect */
 160         if ((dev->device == PCI_DEVICE_ID_SERVERWORKS_CSB6IDE) ||
 161             (dev->device == PCI_DEVICE_ID_SERVERWORKS_CSB6IDE2)) {
 162                 if (!drive->init_speed) {
 163                         u8 dma_stat = hwif->INB(hwif->dma_status);
 164
 165 dma_pio:
 166                         if (((ultra_enable << (7-drive->dn) & 0x80) == 0x80) &&
 167                             ((dma_stat & (1<<(5+unit))) == (1<<(5+unit)))) {
 168                                 drive->current_speed = drive->init_speed = XFER_UDMA_0 + udma_modes[(ultra_timing >> (4*unit)) & ~(0xF0)];
 169                                 return 0;
 170                         } else if ((dma_timing) &&
 171                                    ((dma_stat&(1<<(5+unit)))==(1<<(5+unit)))) {
 172                                 u8 dmaspeed = dma_timing;
 173
 174                                 dma_timing &= ~0xFF;
 175                                 if ((dmaspeed & 0x20) == 0x20)
 176                                         dmaspeed = XFER_MW_DMA_2;
 177                                 else if ((dmaspeed & 0x21) == 0x21)
 178                                         dmaspeed = XFER_MW_DMA_1;
 179                                 else if ((dmaspeed & 0x77) == 0x77)
 180                                         dmaspeed = XFER_MW_DMA_0;
 181                                 else
 182                                         goto dma_pio;
 183                                 drive->current_speed = drive->init_speed = dmaspeed;
 184                                 return 0;
 185                         } else if (pio_timing) {
 186                                 u8 piospeed = pio_timing;
 187
 188                                 pio_timing &= ~0xFF;
 189                                 if ((piospeed & 0x20) == 0x20)
 190                                         piospeed = XFER_PIO_4;
 191                                 else if ((piospeed & 0x22) == 0x22)
 192                                         piospeed = XFER_PIO_3;
 193                                 else if ((piospeed & 0x34) == 0x34)
 194                                         piospeed = XFER_PIO_2;
 195                                 else if ((piospeed & 0x47) == 0x47)
 196                                         piospeed = XFER_PIO_1;
 197                                 else if ((piospeed & 0x5d) == 0x5d)
 198                                         piospeed = XFER_PIO_0;
 199                                 else
 200                                         goto oem_setup_failed;
 201                                 drive->current_speed = drive->init_speed = piospeed;
 202                                 return 0;
 203                         }
 204                 }
 205         }
 206
 207 oem_setup_failed:
 208
 209         pio_timing      &= ~0xFF;
 210         dma_timing      &= ~0xFF;
 211         ultra_timing    &= ~(0x0F << (4*unit));
 212         ultra_enable    &= ~(0x01 << drive->dn);
 213         csb5_pio        &= ~(0x0F << (4*drive->dn));
 214
 215         switch(speed) {
 216                 case XFER_PIO_4:
 217                 case XFER_PIO_3:
 218                 case XFER_PIO_2:
 219                 case XFER_PIO_1:
 220                 case XFER_PIO_0:
 221                         pio_timing |= pio_modes[speed - XFER_PIO_0];
 222                         csb5_pio   |= ((speed - XFER_PIO_0) << (4*drive->dn));
 223                         break;
 224
 225                 case XFER_MW_DMA_2:
 226                 case XFER_MW_DMA_1:
 227                 case XFER_MW_DMA_0:
 228                         pio_timing |= pio_modes[pio];
 229                         csb5_pio   |= (pio << (4*drive->dn));
 230                         dma_timing |= dma_modes[speed - XFER_MW_DMA_0];
 231                         break;
 232
 233                 case XFER_UDMA_5:
 234                 case XFER_UDMA_4:
 235                 case XFER_UDMA_3:
 236                 case XFER_UDMA_2:
 237                 case XFER_UDMA_1:
 238                 case XFER_UDMA_0:
 239                         pio_timing   |= pio_modes[pio];
 240                         csb5_pio     |= (pio << (4*drive->dn));
 241                         dma_timing   |= dma_modes[2];
 242                         ultra_timing |= ((udma_modes[speed - XFER_UDMA_0]) << (4*unit));
 243                         ultra_enable |= (0x01 << drive->dn);
 244                 default:
 245                         break;
 246         }
 247
 248         pci_write_config_byte(dev, drive_pci[drive->dn], pio_timing);
 249         if (csb5)
 250                 pci_write_config_word(dev, 0x4A, csb5_pio);
 251
 252         pci_write_config_byte(dev, drive_pci2[drive->dn], dma_timing);
 253         pci_write_config_byte(dev, (0x56|hwif->channel), ultra_timing);
 254         pci_write_config_byte(dev, 0x54, ultra_enable);
 255
 256         return (ide_config_drive_speed(drive, speed));
 257 }
 258
 259 static void config_chipset_for_pio (ide_drive_t *drive)
 260 {
 261         u16 eide_pio_timing[6] = {960, 480, 240, 180, 120, 90};
 262         u16 xfer_pio = drive->id->eide_pio_modes;
 263         u8 timing, speed, pio;
 264
 265         pio = ide_get_best_pio_mode(drive, 255, 5, NULL);
 266
 267         if (xfer_pio > 4)
 268                 xfer_pio = 0;
 269
 270         if (drive->id->eide_pio_iordy > 0)
 271                 for (xfer_pio = 5;
 272                         xfer_pio>0 &&
 273                         drive->id->eide_pio_iordy>eide_pio_timing[xfer_pio];
 274                         xfer_pio--);
 275         else
 276                 xfer_pio = (drive->id->eide_pio_modes & 4) ? 0x05 :
 277                            (drive->id->eide_pio_modes & 2) ? 0x04 :
 278                            (drive->id->eide_pio_modes & 1) ? 0x03 :
 279                            (drive->id->tPIO & 2) ? 0x02 :
 280                            (drive->id->tPIO & 1) ? 0x01 : xfer_pio;
 281
 282         timing = (xfer_pio >= pio) ? xfer_pio : pio;
 283
 284         switch(timing) {
 285                 case 4: speed = XFER_PIO_4;break;
 286                 case 3: speed = XFER_PIO_3;break;
 287                 case 2: speed = XFER_PIO_2;break;
 288                 case 1: speed = XFER_PIO_1;break;
 289                 default:
 290                         speed = (!drive->id->tPIO) ? XFER_PIO_0 : XFER_PIO_SLOW;
 291                         break;
 292         }
 293         (void) svwks_tune_chipset(drive, speed);
 294         drive->current_speed = speed;
 295 }
 296
 297 static void svwks_tune_drive (ide_drive_t *drive, u8 pio)
 298 {
 299         if(pio == 255)
 300                 (void) svwks_tune_chipset(drive, 255);
 301         else
 302                 (void) svwks_tune_chipset(drive, (XFER_PIO_0 + pio));
 303 }
 304
 305 static int config_chipset_for_dma (ide_drive_t *drive)
 306 {
 307         u8 speed = ide_dma_speed(drive, svwks_ratemask(drive));
 308
 309         if (!(speed))
 310                 speed = XFER_PIO_0 + ide_get_best_pio_mode(drive, 255, 5, NULL);
 311
 312         (void) svwks_tune_chipset(drive, speed);
 313         return ide_dma_enable(drive);
 314 }
 315
 316 static int svwks_config_drive_xfer_rate (ide_drive_t *drive)
 317 {
 318         ide_hwif_t *hwif        = HWIF(drive);
 319         struct hd_driveid *id   = drive->id;
 320
 321         drive->init_speed = 0;
 322
 323         if ((id->capability & 1) && drive->autodma) {
 324
 325                 if (ide_use_dma(drive)) {
 326                         if (config_chipset_for_dma(drive))
 327                                 return hwif->ide_dma_on(drive);
 328                 }
 329
 330                 goto fast_ata_pio;
 331
 332         } else if ((id->capability & 8) || (id->field_valid & 2)) {
 333 fast_ata_pio:
 334                 config_chipset_for_pio(drive);
 335                 //      hwif->tuneproc(drive, 5);
 336                 return hwif->ide_dma_off_quietly(drive);
 337         }
 338         /* IORDY not supported */
 339         return 0;
 340 }
 341
 342 /* This can go soon */
 343
 344 static int svwks_ide_dma_end (ide_drive_t *drive)
 345 {
 346         return __ide_dma_end(drive);
 347 }
 348
 349 static unsigned int __devinit init_chipset_svwks (struct pci_dev *dev, const char *name)
 350 {
 351         unsigned int reg;
 352         u8 btr;
 353
 354         /* save revision id to determine DMA capability */
 355         pci_read_config_byte(dev, PCI_REVISION_ID, &svwks_revision);
 356
 357         /* force Master Latency Timer value to 64 PCICLKs */
 358         pci_write_config_byte(dev, PCI_LATENCY_TIMER, 0x40);
 359
 360         /* OSB4 : South Bridge and IDE */
 361         if (dev->device == PCI_DEVICE_ID_SERVERWORKS_OSB4IDE) {
 362                 isa_dev = pci_find_device(PCI_VENDOR_ID_SERVERWORKS,
 363                           PCI_DEVICE_ID_SERVERWORKS_OSB4, NULL);
 364                 if (isa_dev) {
 365                         pci_read_config_dword(isa_dev, 0x64, &reg);
 366                         reg &= ~0x00002000; /* disable 600ns interrupt mask */
 367                         if(!(reg & 0x00004000))
 368                                 printk(KERN_DEBUG "%s: UDMA not BIOS enabled.\n", name);
 369                         reg |=  0x00004000; /* enable UDMA/33 support */
 370                         pci_write_config_dword(isa_dev, 0x64, reg);
 371                 }
 372         }
 373
 374         /* setup CSB5/CSB6 : South Bridge and IDE option RAID */
 375         else if ((dev->device == PCI_DEVICE_ID_SERVERWORKS_CSB5IDE) ||
 376                  (dev->device == PCI_DEVICE_ID_SERVERWORKS_CSB6IDE) ||
 377                  (dev->device == PCI_DEVICE_ID_SERVERWORKS_CSB6IDE2)) {
 378
 379                 /* Third Channel Test */
 380                 if (!(PCI_FUNC(dev->devfn) & 1)) {
 381                         struct pci_dev * findev = NULL;
 382                         u32 reg4c = 0;
 383                         findev = pci_find_device(PCI_VENDOR_ID_SERVERWORKS,
 384                                 PCI_DEVICE_ID_SERVERWORKS_CSB5, NULL);
 385                         if (findev) {
 386                                 pci_read_config_dword(findev, 0x4C, &reg4c);
 387                                 reg4c &= ~0x000007FF;
 388                                 reg4c |=  0x00000040;
 389                                 reg4c |=  0x00000020;
 390                                 pci_write_config_dword(findev, 0x4C, reg4c);
 391                         }
 392                         outb_p(0x06, 0x0c00);
 393                         dev->irq = inb_p(0x0c01);
 394                 } else {
 395                         struct pci_dev * findev = NULL;
 396                         u8 reg41 = 0;
 397
 398                         findev = pci_find_device(PCI_VENDOR_ID_SERVERWORKS,
 399                                         PCI_DEVICE_ID_SERVERWORKS_CSB6, NULL);
 400                         if (findev) {
 401                                 pci_read_config_byte(findev, 0x41, &reg41);
 402                                 reg41 &= ~0x40;
 403                                 pci_write_config_byte(findev, 0x41, reg41);
 404                         }
 405                         /*
 406                          * This is a device pin issue on CSB6.
 407                          * Since there will be a future raid mode,
 408                          * early versions of the chipset require the
 409                          * interrupt pin to be set, and it is a compatibility
 410                          * mode issue.
 411                          */
 412                         if ((dev->class >> 8) == PCI_CLASS_STORAGE_IDE)
 413                                 dev->irq = 0;
 414                 }
 415 //              pci_read_config_dword(dev, 0x40, &pioreg)
 416 //              pci_write_config_dword(dev, 0x40, 0x99999999);
 417 //              pci_read_config_dword(dev, 0x44, &dmareg);
 418 //              pci_write_config_dword(dev, 0x44, 0xFFFFFFFF);
 419                 /* setup the UDMA Control register
 420                  *
 421                  * 1. clear bit 6 to enable DMA
 422                  * 2. enable DMA modes with bits 0-1
 423                  *      00 : legacy
 424                  *      01 : udma2
 425                  *      10 : udma2/udma4
 426                  *      11 : udma2/udma4/udma5
 427                  */
 428                 pci_read_config_byte(dev, 0x5A, &btr);
 429                 btr &= ~0x40;
 430                 if (!(PCI_FUNC(dev->devfn) & 1))
 431                         btr |= 0x2;
 432                 else
 433                         btr |= (svwks_revision >= SVWKS_CSB5_REVISION_NEW) ? 0x3 : 0x2;
 434                 pci_write_config_byte(dev, 0x5A, btr);
 435         }
 436         /* Setup HT1000 SouthBridge Controller - Single Channel Only */
 437         else if (dev->device == PCI_DEVICE_ID_SERVERWORKS_HT1000IDE) {
 438                 pci_read_config_byte(dev, 0x5A, &btr);
 439                 btr &= ~0x40;
 440                 btr |= 0x3;
 441                 pci_write_config_byte(dev, 0x5A, btr);
 442         }
 443
 444         return dev->irq;
 445 }
 446
 447 static unsigned int __devinit ata66_svwks_svwks (ide_hwif_t *hwif)
 448 {
 449         return 1;
 450 }
 451
 452 /* On Dell PowerEdge servers with a CSB5/CSB6, the top two bits
 453  * of the subsystem device ID indicate presence of an 80-pin cable.
 454  * Bit 15 clear = secondary IDE channel does not have 80-pin cable.
 455  * Bit 15 set   = secondary IDE channel has 80-pin cable.
 456  * Bit 14 clear = primary IDE channel does not have 80-pin cable.
 457  * Bit 14 set   = primary IDE channel has 80-pin cable.
 458  */
 459 static unsigned int __devinit ata66_svwks_dell (ide_hwif_t *hwif)
 460 {
 461         struct pci_dev *dev = hwif->pci_dev;
 462         if (dev->subsystem_vendor == PCI_VENDOR_ID_DELL &&
 463             dev->vendor == PCI_VENDOR_ID_SERVERWORKS &&
 464             (dev->device == PCI_DEVICE_ID_SERVERWORKS_CSB5IDE ||
 465              dev->device == PCI_DEVICE_ID_SERVERWORKS_CSB6IDE))
 466                 return ((1 << (hwif->channel + 14)) &
 467                         dev->subsystem_device) ? 1 : 0;
 468         return 0;
 469 }
 470
 471 /* Sun Cobalt Alpine hardware avoids the 80-pin cable
 472  * detect issue by attaching the drives directly to the board.
 473  * This check follows the Dell precedent (how scary is that?!)
 474  *
 475  * WARNING: this only works on Alpine hardware!
 476  */
 477 static unsigned int __devinit ata66_svwks_cobalt (ide_hwif_t *hwif)
 478 {
 479         struct pci_dev *dev = hwif->pci_dev;
 480         if (dev->subsystem_vendor == PCI_VENDOR_ID_SUN &&
 481             dev->vendor == PCI_VENDOR_ID_SERVERWORKS &&
 482             dev->device == PCI_DEVICE_ID_SERVERWORKS_CSB5IDE)
 483                 return ((1 << (hwif->channel + 14)) &
 484                         dev->subsystem_device) ? 1 : 0;
 485         return 0;
 486 }
 487
 488 static unsigned int __devinit ata66_svwks (ide_hwif_t *hwif)
 489 {
 490         struct pci_dev *dev = hwif->pci_dev;
 491
 492         /* Server Works */
 493         if (dev->subsystem_vendor == PCI_VENDOR_ID_SERVERWORKS)
 494                 return ata66_svwks_svwks (hwif);
 495
 496         /* Dell PowerEdge */
 497         if (dev->subsystem_vendor == PCI_VENDOR_ID_DELL)
 498                 return ata66_svwks_dell (hwif);
 499
 500         /* Cobalt Alpine */
 501         if (dev->subsystem_vendor == PCI_VENDOR_ID_SUN)
 502                 return ata66_svwks_cobalt (hwif);
 503
 504         /* Per Specified Design by OEM, and ASIC Architect */
 505         if ((dev->device == PCI_DEVICE_ID_SERVERWORKS_CSB6IDE) ||
 506             (dev->device == PCI_DEVICE_ID_SERVERWORKS_CSB6IDE2))
 507                 return 1;
 508
 509         return 0;
 510 }
 511
 512 static void __devinit init_hwif_svwks (ide_hwif_t *hwif)
 513 {
 514         u8 dma_stat = 0;
 515
 516         if (!hwif->irq)
 517                 hwif->irq = hwif->channel ? 15 : 14;
 518
 519         hwif->tuneproc = &svwks_tune_drive;
 520         hwif->speedproc = &svwks_tune_chipset;
 521
 522         hwif->atapi_dma = 1;
 523
 524         if (hwif->pci_dev->device != PCI_DEVICE_ID_SERVERWORKS_OSB4IDE)
 525                 hwif->ultra_mask = 0x3f;
 526
 527         hwif->mwdma_mask = 0x07;
 528
 529         hwif->autodma = 0;
 530
 531         if (!hwif->dma_base) {
 532                 hwif->drives[0].autotune = 1;
 533                 hwif->drives[1].autotune = 1;
 534                 return;
 535         }
 536
 537         hwif->ide_dma_check = &svwks_config_drive_xfer_rate;
 538         if (hwif->pci_dev->device == PCI_DEVICE_ID_SERVERWORKS_OSB4IDE)
 539                 hwif->ide_dma_end = &svwks_ide_dma_end;
 540         else if (!(hwif->udma_four))
 541                 hwif->udma_four = ata66_svwks(hwif);
 542         if (!noautodma)
 543                 hwif->autodma = 1;
 544
 545         dma_stat = hwif->INB(hwif->dma_status);
 546         hwif->drives[0].autodma = (dma_stat & 0x20);
 547         hwif->drives[1].autodma = (dma_stat & 0x40);
 548         hwif->drives[0].autotune = (!(dma_stat & 0x20));
 549         hwif->drives[1].autotune = (!(dma_stat & 0x40));
 550 }
 551
 552 /*
 553  * We allow the BM-DMA driver to only work on enabled interfaces.
 554  */
 555 static void __devinit init_dma_svwks (ide_hwif_t *hwif, unsigned long dmabase)
 556 {
 557         struct pci_dev *dev = hwif->pci_dev;
 558
 559         if (((dev->device == PCI_DEVICE_ID_SERVERWORKS_CSB6IDE) ||
 560              (dev->device == PCI_DEVICE_ID_SERVERWORKS_CSB6IDE2)) &&
 561             (!(PCI_FUNC(dev->devfn) & 1)) && (hwif->channel))
 562                 return;
 563
 564         ide_setup_dma(hwif, dmabase, 8);
 565 }
 566
 567 static int __devinit init_setup_svwks (struct pci_dev *dev, ide_pci_device_t *d)
 568 {
 569         return ide_setup_pci_device(dev, d);
 570 }
 571
 572 static int __devinit init_setup_csb6 (struct pci_dev *dev, ide_pci_device_t *d)
 573 {
 574         if (!(PCI_FUNC(dev->devfn) & 1)) {
 575                 d->bootable = NEVER_BOARD;
 576                 if (dev->resource[0].start == 0x01f1)
 577                         d->bootable = ON_BOARD;
 578         }
 579
 580         d->channels = ((dev->device == PCI_DEVICE_ID_SERVERWORKS_CSB6IDE ||
 581                         dev->device == PCI_DEVICE_ID_SERVERWORKS_CSB6IDE2) &&
 582                        (!(PCI_FUNC(dev->devfn) & 1))) ? 1 : 2;
 583
 584         return ide_setup_pci_device(dev, d);
 585 }
 586
 587 static ide_pci_device_t serverworks_chipsets[] __devinitdata = {
 588         {       /* 0 */
 589                 .name           = "SvrWks OSB4",
 590                 .init_setup     = init_setup_svwks,
 591                 .init_chipset   = init_chipset_svwks,
 592                 .init_hwif      = init_hwif_svwks,
 593                 .channels       = 2,
 594                 .autodma        = AUTODMA,
 595                 .bootable       = ON_BOARD,
 596         },{     /* 1 */
 597                 .name           = "SvrWks CSB5",
 598                 .init_setup     = init_setup_svwks,
 599                 .init_chipset   = init_chipset_svwks,
 600                 .init_hwif      = init_hwif_svwks,
 601                 .init_dma       = init_dma_svwks,
 602                 .channels       = 2,
 603                 .autodma        = AUTODMA,
 604                 .bootable       = ON_BOARD,
 605         },{     /* 2 */
 606                 .name           = "SvrWks CSB6",
 607                 .init_setup     = init_setup_csb6,
 608                 .init_chipset   = init_chipset_svwks,
 609                 .init_hwif      = init_hwif_svwks,
 610                 .init_dma       = init_dma_svwks,
 611                 .channels       = 2,
 612                 .autodma        = AUTODMA,
 613                 .bootable       = ON_BOARD,
 614         },{     /* 3 */
 615                 .name           = "SvrWks CSB6",
 616                 .init_setup     = init_setup_csb6,
 617                 .init_chipset   = init_chipset_svwks,
 618                 .init_hwif      = init_hwif_svwks,
 619                 .init_dma       = init_dma_svwks,
 620                 .channels       = 1,    /* 2 */
 621                 .autodma        = AUTODMA,
 622                 .bootable       = ON_BOARD,
 623         },{     /* 4 */
 624                 .name           = "SvrWks HT1000",
 625                 .init_setup     = init_setup_svwks,
 626                 .init_chipset   = init_chipset_svwks,
 627                 .init_hwif      = init_hwif_svwks,
 628                 .init_dma       = init_dma_svwks,
 629                 .channels       = 1,    /* 2 */
 630                 .autodma        = AUTODMA,
 631                 .bootable       = ON_BOARD,
 632         }
 633 };
 634
 635 /**
 636  *      svwks_init_one  -       called when a OSB/CSB is found
 637  *      @dev: the svwks device
 638  *      @id: the matching pci id
 639  *
 640  *      Called when the PCI registration layer (or the IDE initialization)
 641  *      finds a device matching our IDE device tables.
 642  */
 643
 644 static int __devinit svwks_init_one(struct pci_dev *dev, const struct pci_device_id *id)
 645 {
 646         ide_pci_device_t *d = &serverworks_chipsets[id->driver_data];
 647
 648         return d->init_setup(dev, d);
 649 }
 650
 651 static struct pci_device_id svwks_pci_tbl[] = {
 652         { PCI_VENDOR_ID_SERVERWORKS, PCI_DEVICE_ID_SERVERWORKS_OSB4IDE, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 0},
 653         { PCI_VENDOR_ID_SERVERWORKS, PCI_DEVICE_ID_SERVERWORKS_CSB5IDE, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 1},
 654         { PCI_VENDOR_ID_SERVERWORKS, PCI_DEVICE_ID_SERVERWORKS_CSB6IDE, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 2},
 655         { PCI_VENDOR_ID_SERVERWORKS, PCI_DEVICE_ID_SERVERWORKS_CSB6IDE2, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 3},
 656         { PCI_VENDOR_ID_SERVERWORKS, PCI_DEVICE_ID_SERVERWORKS_HT1000IDE, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 4},
 657         { 0, },
 658 };
 659 MODULE_DEVICE_TABLE(pci, svwks_pci_tbl);
 660
 661 static struct pci_driver driver = {
 662         .name           = "Serverworks_IDE",
 663         .id_table       = svwks_pci_tbl,
 664         .probe          = svwks_init_one,
 665 };
 666
 667 static int svwks_ide_init(void)
 668 {
 669         return ide_pci_register_driver(&driver);
 670 }
 671
 672 module_init(svwks_ide_init);
 673
 674 MODULE_AUTHOR("Michael Aubry. Andrzej Krzysztofowicz, Andre Hedrick");
 675 MODULE_DESCRIPTION("PCI driver module for Serverworks OSB4/CSB5/CSB6 IDE");
 676 MODULE_LICENSE("GPL");