2 * Driver for DBRI sound chip found on Sparcs.
3 * Copyright (C) 2004, 2005 Martin Habets (mhabets@users.sourceforge.net)
5 * Converted to ring buffered version by Krzysztof Helt (krzysztof.h1@wp.pl)
7 * Based entirely upon drivers/sbus/audio/dbri.c which is:
8 * Copyright (C) 1997 Rudolf Koenig (rfkoenig@immd4.informatik.uni-erlangen.de)
9 * Copyright (C) 1998, 1999 Brent Baccala (baccala@freesoft.org)
11 * This is the low level driver for the DBRI & MMCODEC duo used for ISDN & AUDIO
12 * on Sun SPARCStation 10, 20, LX and Voyager models.
14 * - DBRI: AT&T T5900FX Dual Basic Rates ISDN Interface. It is a 32 channel
15 * data time multiplexer with ISDN support (aka T7259)
16 * Interfaces: SBus,ISDN NT & TE, CHI, 4 bits parallel.
17 * CHI: (spelled ki) Concentration Highway Interface (AT&T or Intel bus ?).
19 * - "STP 4000SBus Dual Basic Rate ISDN (DBRI) Transceiver" from
20 * Sparc Technology Business (courtesy of Sun Support)
21 * - Data sheet of the T7903, a newer but very similar ISA bus equivalent
22 * available from the Lucent (formerly AT&T microelectronics) home
24 * - http://www.freesoft.org/Linux/DBRI/
25 * - MMCODEC: Crystal Semiconductor CS4215 16 bit Multimedia Audio Codec
26 * Interfaces: CHI, Audio In & Out, 2 bits parallel
27 * Documentation: from the Crystal Semiconductor home page.
29 * The DBRI is a 32 pipe machine, each pipe can transfer some bits between
30 * memory and a serial device (long pipes, no. 0-15) or between two serial
31 * devices (short pipes, no. 16-31), or simply send a fixed data to a serial
32 * device (short pipes).
33 * A timeslot defines the bit-offset and no. of bits read from a serial device.
34 * The timeslots are linked to 6 circular lists, one for each direction for
35 * each serial device (NT,TE,CHI). A timeslot is associated to 1 or 2 pipes
36 * (the second one is a monitor/tee pipe, valid only for serial input).
38 * The mmcodec is connected via the CHI bus and needs the data & some
39 * parameters (volume, output selection) time multiplexed in 8 byte
40 * chunks. It also has a control mode, which serves for audio format setting.
42 * Looking at the CS4215 data sheet it is easy to set up 2 or 4 codecs on
43 * the same CHI bus, so I thought perhaps it is possible to use the on-board
44 * & the speakerbox codec simultaneously, giving 2 (not very independent :-)
45 * audio devices. But the SUN HW group decided against it, at least on my
46 * LX the speakerbox connector has at least 1 pin missing and 1 wrongly
49 * I've tried to stick to the following function naming conventions:
51 * cs4215_* CS4215 codec specific stuff
52 * dbri_* DBRI high-level stuff
53 * other DBRI low-level stuff
56 #include <sound/driver.h>
57 #include <linux/interrupt.h>
58 #include <linux/delay.h>
59 #include <linux/irq.h>
62 #include <sound/core.h>
63 #include <sound/pcm.h>
64 #include <sound/pcm_params.h>
65 #include <sound/info.h>
66 #include <sound/control.h>
67 #include <sound/initval.h>
70 #include <asm/atomic.h>
72 MODULE_AUTHOR("Rudolf Koenig, Brent Baccala and Martin Habets");
73 MODULE_DESCRIPTION("Sun DBRI");
74 MODULE_LICENSE("GPL");
75 MODULE_SUPPORTED_DEVICE("{{Sun,DBRI}}");
77 static int index[SNDRV_CARDS] = SNDRV_DEFAULT_IDX; /* Index 0-MAX */
78 static char *id[SNDRV_CARDS] = SNDRV_DEFAULT_STR; /* ID for this card */
79 /* Enable this card */
80 static int enable[SNDRV_CARDS] = SNDRV_DEFAULT_ENABLE_PNP;
82 module_param_array(index, int, NULL, 0444);
83 MODULE_PARM_DESC(index, "Index value for Sun DBRI soundcard.");
84 module_param_array(id, charp, NULL, 0444);
85 MODULE_PARM_DESC(id, "ID string for Sun DBRI soundcard.");
86 module_param_array(enable, bool, NULL, 0444);
87 MODULE_PARM_DESC(enable, "Enable Sun DBRI soundcard.");
98 static int dbri_debug;
99 module_param(dbri_debug, int, 0644);
100 MODULE_PARM_DESC(dbri_debug, "Debug value for Sun DBRI soundcard.");
103 static char *cmds[] = {
104 "WAIT", "PAUSE", "JUMP", "IIQ", "REX", "SDP", "CDP", "DTS",
105 "SSP", "CHI", "NT", "TE", "CDEC", "TEST", "CDM", "RESRV"
108 #define dprintk(a, x...) if (dbri_debug & a) printk(KERN_DEBUG x)
111 #define dprintk(a, x...) do { } while (0)
113 #endif /* DBRI_DEBUG */
115 #define DBRI_CMD(cmd, intr, value) ((cmd << 28) | \
119 /***************************************************************************
120 CS4215 specific definitions and structures
121 ****************************************************************************/
124 __u8 data[4]; /* Data mode: Time slots 5-8 */
125 __u8 ctrl[4]; /* Ctrl mode: Time slots 1-4 */
127 __u8 offset; /* Bit offset from frame sync to time slot 1 */
128 volatile __u32 status;
129 volatile __u32 version;
130 __u8 precision; /* In bits, either 8 or 16 */
131 __u8 channels; /* 1 or 2 */
138 /* Time Slot 1, Status register */
139 #define CS4215_CLB (1<<2) /* Control Latch Bit */
140 #define CS4215_OLB (1<<3) /* 1: line: 2.0V, speaker 4V */
141 /* 0: line: 2.8V, speaker 8V */
142 #define CS4215_MLB (1<<4) /* 1: Microphone: 20dB gain disabled */
143 #define CS4215_RSRVD_1 (1<<5)
145 /* Time Slot 2, Data Format Register */
146 #define CS4215_DFR_LINEAR16 0
147 #define CS4215_DFR_ULAW 1
148 #define CS4215_DFR_ALAW 2
149 #define CS4215_DFR_LINEAR8 3
150 #define CS4215_DFR_STEREO (1<<2)
156 { 8000, (1 << 4), (0 << 3) },
157 { 16000, (1 << 4), (1 << 3) },
158 { 27429, (1 << 4), (2 << 3) }, /* Actually 24428.57 */
159 { 32000, (1 << 4), (3 << 3) },
160 /* { NA, (1 << 4), (4 << 3) }, */
161 /* { NA, (1 << 4), (5 << 3) }, */
162 { 48000, (1 << 4), (6 << 3) },
163 { 9600, (1 << 4), (7 << 3) },
164 { 5512, (2 << 4), (0 << 3) }, /* Actually 5512.5 */
165 { 11025, (2 << 4), (1 << 3) },
166 { 18900, (2 << 4), (2 << 3) },
167 { 22050, (2 << 4), (3 << 3) },
168 { 37800, (2 << 4), (4 << 3) },
169 { 44100, (2 << 4), (5 << 3) },
170 { 33075, (2 << 4), (6 << 3) },
171 { 6615, (2 << 4), (7 << 3) },
175 #define CS4215_HPF (1<<7) /* High Pass Filter, 1: Enabled */
177 #define CS4215_12_MASK 0xfcbf /* Mask off reserved bits in slot 1 & 2 */
179 /* Time Slot 3, Serial Port Control register */
180 #define CS4215_XEN (1<<0) /* 0: Enable serial output */
181 #define CS4215_XCLK (1<<1) /* 1: Master mode: Generate SCLK */
182 #define CS4215_BSEL_64 (0<<2) /* Bitrate: 64 bits per frame */
183 #define CS4215_BSEL_128 (1<<2)
184 #define CS4215_BSEL_256 (2<<2)
185 #define CS4215_MCK_MAST (0<<4) /* Master clock */
186 #define CS4215_MCK_XTL1 (1<<4) /* 24.576 MHz clock source */
187 #define CS4215_MCK_XTL2 (2<<4) /* 16.9344 MHz clock source */
188 #define CS4215_MCK_CLK1 (3<<4) /* Clockin, 256 x Fs */
189 #define CS4215_MCK_CLK2 (4<<4) /* Clockin, see DFR */
191 /* Time Slot 4, Test Register */
192 #define CS4215_DAD (1<<0) /* 0:Digital-Dig loop, 1:Dig-Analog-Dig loop */
193 #define CS4215_ENL (1<<1) /* Enable Loopback Testing */
195 /* Time Slot 5, Parallel Port Register */
196 /* Read only here and the same as the in data mode */
198 /* Time Slot 6, Reserved */
200 /* Time Slot 7, Version Register */
201 #define CS4215_VERSION_MASK 0xf /* Known versions 0/C, 1/D, 2/E */
203 /* Time Slot 8, Reserved */
208 /* Time Slot 1-2: Left Channel Data, 2-3: Right Channel Data */
210 /* Time Slot 5, Output Setting */
211 #define CS4215_LO(v) v /* Left Output Attenuation 0x3f: -94.5 dB */
212 #define CS4215_LE (1<<6) /* Line Out Enable */
213 #define CS4215_HE (1<<7) /* Headphone Enable */
215 /* Time Slot 6, Output Setting */
216 #define CS4215_RO(v) v /* Right Output Attenuation 0x3f: -94.5 dB */
217 #define CS4215_SE (1<<6) /* Speaker Enable */
218 #define CS4215_ADI (1<<7) /* A/D Data Invalid: Busy in calibration */
220 /* Time Slot 7, Input Setting */
221 #define CS4215_LG(v) v /* Left Gain Setting 0xf: 22.5 dB */
222 #define CS4215_IS (1<<4) /* Input Select: 1=Microphone, 0=Line */
223 #define CS4215_OVR (1<<5) /* 1: Over range condition occurred */
224 #define CS4215_PIO0 (1<<6) /* Parallel I/O 0 */
225 #define CS4215_PIO1 (1<<7)
227 /* Time Slot 8, Input Setting */
228 #define CS4215_RG(v) v /* Right Gain Setting 0xf: 22.5 dB */
229 #define CS4215_MA(v) (v<<4) /* Monitor Path Attenuation 0xf: mute */
231 /***************************************************************************
232 DBRI specific definitions and structures
233 ****************************************************************************/
235 /* DBRI main registers */
236 #define REG0 0x00UL /* Status and Control */
237 #define REG1 0x04UL /* Mode and Interrupt */
238 #define REG2 0x08UL /* Parallel IO */
239 #define REG3 0x0cUL /* Test */
240 #define REG8 0x20UL /* Command Queue Pointer */
241 #define REG9 0x24UL /* Interrupt Queue Pointer */
243 #define DBRI_NO_CMDS 64
244 #define DBRI_INT_BLK 64
245 #define DBRI_NO_DESCS 64
246 #define DBRI_NO_PIPES 32
247 #define DBRI_MAX_PIPE (DBRI_NO_PIPES - 1)
251 #define DBRI_NO_STREAMS 2
253 /* One transmit/receive descriptor */
254 /* When ba != 0 descriptor is used */
256 volatile __u32 word1;
257 __u32 ba; /* Transmit/Receive Buffer Address */
258 __u32 nda; /* Next Descriptor Address */
259 volatile __u32 word4;
262 /* This structure is in a DMA region where it can accessed by both
263 * the CPU and the DBRI
266 s32 cmd[DBRI_NO_CMDS]; /* Place for commands */
267 volatile s32 intr[DBRI_INT_BLK]; /* Interrupt field */
268 struct dbri_mem desc[DBRI_NO_DESCS]; /* Xmit/receive descriptors */
271 #define dbri_dma_off(member, elem) \
272 ((u32)(unsigned long) \
273 (&(((struct dbri_dma *)0)->member[elem])))
275 enum in_or_out { PIPEinput, PIPEoutput };
278 u32 sdp; /* SDP command word */
279 int nextpipe; /* Next pipe in linked list */
280 int length; /* Length of timeslot (bits) */
281 int first_desc; /* Index of first descriptor */
282 int desc; /* Index of active descriptor */
283 volatile __u32 *recv_fixed_ptr; /* Ptr to receive fixed data */
286 /* Per stream (playback or record) information */
287 struct dbri_streaminfo {
288 struct snd_pcm_substream *substream;
289 u32 dvma_buffer; /* Device view of ALSA DMA buffer */
290 int size; /* Size of DMA buffer */
291 size_t offset; /* offset in user buffer */
292 int pipe; /* Data pipe used */
293 int left_gain; /* mixer elements */
297 /* This structure holds the information for both chips (DBRI & CS4215) */
299 struct snd_card *card; /* ALSA card */
301 int regs_size, irq; /* Needed for unload */
302 struct sbus_dev *sdev; /* SBUS device info */
305 struct dbri_dma *dma; /* Pointer to our DMA block */
306 u32 dma_dvma; /* DBRI visible DMA address */
308 void __iomem *regs; /* dbri HW regs */
309 int dbri_irqp; /* intr queue pointer */
311 struct dbri_pipe pipes[DBRI_NO_PIPES]; /* DBRI's 32 data pipes */
312 int next_desc[DBRI_NO_DESCS]; /* Index of next desc, or -1 */
313 spinlock_t cmdlock; /* Protects cmd queue accesses */
314 s32 *cmdptr; /* Pointer to the last queued cmd */
318 struct cs4215 mm; /* mmcodec special info */
319 /* per stream (playback/record) info */
320 struct dbri_streaminfo stream_info[DBRI_NO_STREAMS];
322 struct snd_dbri *next;
325 #define DBRI_MAX_VOLUME 63 /* Output volume */
326 #define DBRI_MAX_GAIN 15 /* Input gain */
328 /* DBRI Reg0 - Status Control Register - defines. (Page 17) */
329 #define D_P (1<<15) /* Program command & queue pointer valid */
330 #define D_G (1<<14) /* Allow 4-Word SBus Burst */
331 #define D_S (1<<13) /* Allow 16-Word SBus Burst */
332 #define D_E (1<<12) /* Allow 8-Word SBus Burst */
333 #define D_X (1<<7) /* Sanity Timer Disable */
334 #define D_T (1<<6) /* Permit activation of the TE interface */
335 #define D_N (1<<5) /* Permit activation of the NT interface */
336 #define D_C (1<<4) /* Permit activation of the CHI interface */
337 #define D_F (1<<3) /* Force Sanity Timer Time-Out */
338 #define D_D (1<<2) /* Disable Master Mode */
339 #define D_H (1<<1) /* Halt for Analysis */
340 #define D_R (1<<0) /* Soft Reset */
342 /* DBRI Reg1 - Mode and Interrupt Register - defines. (Page 18) */
343 #define D_LITTLE_END (1<<8) /* Byte Order */
344 #define D_BIG_END (0<<8) /* Byte Order */
345 #define D_MRR (1<<4) /* Multiple Error Ack on SBus (read only) */
346 #define D_MLE (1<<3) /* Multiple Late Error on SBus (read only) */
347 #define D_LBG (1<<2) /* Lost Bus Grant on SBus (read only) */
348 #define D_MBE (1<<1) /* Burst Error on SBus (read only) */
349 #define D_IR (1<<0) /* Interrupt Indicator (read only) */
351 /* DBRI Reg2 - Parallel IO Register - defines. (Page 18) */
352 #define D_ENPIO3 (1<<7) /* Enable Pin 3 */
353 #define D_ENPIO2 (1<<6) /* Enable Pin 2 */
354 #define D_ENPIO1 (1<<5) /* Enable Pin 1 */
355 #define D_ENPIO0 (1<<4) /* Enable Pin 0 */
356 #define D_ENPIO (0xf0) /* Enable all the pins */
357 #define D_PIO3 (1<<3) /* Pin 3: 1: Data mode, 0: Ctrl mode */
358 #define D_PIO2 (1<<2) /* Pin 2: 1: Onboard PDN */
359 #define D_PIO1 (1<<1) /* Pin 1: 0: Reset */
360 #define D_PIO0 (1<<0) /* Pin 0: 1: Speakerbox PDN */
362 /* DBRI Commands (Page 20) */
363 #define D_WAIT 0x0 /* Stop execution */
364 #define D_PAUSE 0x1 /* Flush long pipes */
365 #define D_JUMP 0x2 /* New command queue */
366 #define D_IIQ 0x3 /* Initialize Interrupt Queue */
367 #define D_REX 0x4 /* Report command execution via interrupt */
368 #define D_SDP 0x5 /* Setup Data Pipe */
369 #define D_CDP 0x6 /* Continue Data Pipe (reread NULL Pointer) */
370 #define D_DTS 0x7 /* Define Time Slot */
371 #define D_SSP 0x8 /* Set short Data Pipe */
372 #define D_CHI 0x9 /* Set CHI Global Mode */
373 #define D_NT 0xa /* NT Command */
374 #define D_TE 0xb /* TE Command */
375 #define D_CDEC 0xc /* Codec setup */
376 #define D_TEST 0xd /* No comment */
377 #define D_CDM 0xe /* CHI Data mode command */
379 /* Special bits for some commands */
380 #define D_PIPE(v) ((v)<<0) /* Pipe No.: 0-15 long, 16-21 short */
382 /* Setup Data Pipe */
384 #define D_SDP_2SAME (1<<18) /* Report 2nd time in a row value received */
385 #define D_SDP_CHANGE (2<<18) /* Report any changes */
386 #define D_SDP_EVERY (3<<18) /* Report any changes */
387 #define D_SDP_EOL (1<<17) /* EOL interrupt enable */
388 #define D_SDP_IDLE (1<<16) /* HDLC idle interrupt enable */
391 #define D_SDP_MEM (0<<13) /* To/from memory */
392 #define D_SDP_HDLC (2<<13)
393 #define D_SDP_HDLC_D (3<<13) /* D Channel (prio control) */
394 #define D_SDP_SER (4<<13) /* Serial to serial */
395 #define D_SDP_FIXED (6<<13) /* Short only */
396 #define D_SDP_MODE(v) ((v)&(7<<13))
398 #define D_SDP_TO_SER (1<<12) /* Direction */
399 #define D_SDP_FROM_SER (0<<12) /* Direction */
400 #define D_SDP_MSB (1<<11) /* Bit order within Byte */
401 #define D_SDP_LSB (0<<11) /* Bit order within Byte */
402 #define D_SDP_P (1<<10) /* Pointer Valid */
403 #define D_SDP_A (1<<8) /* Abort */
404 #define D_SDP_C (1<<7) /* Clear */
406 /* Define Time Slot */
407 #define D_DTS_VI (1<<17) /* Valid Input Time-Slot Descriptor */
408 #define D_DTS_VO (1<<16) /* Valid Output Time-Slot Descriptor */
409 #define D_DTS_INS (1<<15) /* Insert Time Slot */
410 #define D_DTS_DEL (0<<15) /* Delete Time Slot */
411 #define D_DTS_PRVIN(v) ((v)<<10) /* Previous In Pipe */
412 #define D_DTS_PRVOUT(v) ((v)<<5) /* Previous Out Pipe */
414 /* Time Slot defines */
415 #define D_TS_LEN(v) ((v)<<24) /* Number of bits in this time slot */
416 #define D_TS_CYCLE(v) ((v)<<14) /* Bit Count at start of TS */
417 #define D_TS_DI (1<<13) /* Data Invert */
418 #define D_TS_1CHANNEL (0<<10) /* Single Channel / Normal mode */
419 #define D_TS_MONITOR (2<<10) /* Monitor pipe */
420 #define D_TS_NONCONTIG (3<<10) /* Non contiguous mode */
421 #define D_TS_ANCHOR (7<<10) /* Starting short pipes */
422 #define D_TS_MON(v) ((v)<<5) /* Monitor Pipe */
423 #define D_TS_NEXT(v) ((v)<<0) /* Pipe no.: 0-15 long, 16-21 short */
425 /* Concentration Highway Interface Modes */
426 #define D_CHI_CHICM(v) ((v)<<16) /* Clock mode */
427 #define D_CHI_IR (1<<15) /* Immediate Interrupt Report */
428 #define D_CHI_EN (1<<14) /* CHIL Interrupt enabled */
429 #define D_CHI_OD (1<<13) /* Open Drain Enable */
430 #define D_CHI_FE (1<<12) /* Sample CHIFS on Rising Frame Edge */
431 #define D_CHI_FD (1<<11) /* Frame Drive */
432 #define D_CHI_BPF(v) ((v)<<0) /* Bits per Frame */
434 /* NT: These are here for completeness */
435 #define D_NT_FBIT (1<<17) /* Frame Bit */
436 #define D_NT_NBF (1<<16) /* Number of bad frames to loose framing */
437 #define D_NT_IRM_IMM (1<<15) /* Interrupt Report & Mask: Immediate */
438 #define D_NT_IRM_EN (1<<14) /* Interrupt Report & Mask: Enable */
439 #define D_NT_ISNT (1<<13) /* Configure interface as NT */
440 #define D_NT_FT (1<<12) /* Fixed Timing */
441 #define D_NT_EZ (1<<11) /* Echo Channel is Zeros */
442 #define D_NT_IFA (1<<10) /* Inhibit Final Activation */
443 #define D_NT_ACT (1<<9) /* Activate Interface */
444 #define D_NT_MFE (1<<8) /* Multiframe Enable */
445 #define D_NT_RLB(v) ((v)<<5) /* Remote Loopback */
446 #define D_NT_LLB(v) ((v)<<2) /* Local Loopback */
447 #define D_NT_FACT (1<<1) /* Force Activation */
448 #define D_NT_ABV (1<<0) /* Activate Bipolar Violation */
451 #define D_CDEC_CK(v) ((v)<<24) /* Clock Select */
452 #define D_CDEC_FED(v) ((v)<<12) /* FSCOD Falling Edge Delay */
453 #define D_CDEC_RED(v) ((v)<<0) /* FSCOD Rising Edge Delay */
456 #define D_TEST_RAM(v) ((v)<<16) /* RAM Pointer */
457 #define D_TEST_SIZE(v) ((v)<<11) /* */
458 #define D_TEST_ROMONOFF 0x5 /* Toggle ROM opcode monitor on/off */
459 #define D_TEST_PROC 0x6 /* Microprocessor test */
460 #define D_TEST_SER 0x7 /* Serial-Controller test */
461 #define D_TEST_RAMREAD 0x8 /* Copy from Ram to system memory */
462 #define D_TEST_RAMWRITE 0x9 /* Copy into Ram from system memory */
463 #define D_TEST_RAMBIST 0xa /* RAM Built-In Self Test */
464 #define D_TEST_MCBIST 0xb /* Microcontroller Built-In Self Test */
465 #define D_TEST_DUMP 0xe /* ROM Dump */
468 #define D_CDM_THI (1 << 8) /* Transmit Data on CHIDR Pin */
469 #define D_CDM_RHI (1 << 7) /* Receive Data on CHIDX Pin */
470 #define D_CDM_RCE (1 << 6) /* Receive on Rising Edge of CHICK */
471 #define D_CDM_XCE (1 << 2) /* Transmit Data on Rising Edge of CHICK */
472 #define D_CDM_XEN (1 << 1) /* Transmit Highway Enable */
473 #define D_CDM_REN (1 << 0) /* Receive Highway Enable */
476 #define D_INTR_BRDY 1 /* Buffer Ready for processing */
477 #define D_INTR_MINT 2 /* Marked Interrupt in RD/TD */
478 #define D_INTR_IBEG 3 /* Flag to idle transition detected (HDLC) */
479 #define D_INTR_IEND 4 /* Idle to flag transition detected (HDLC) */
480 #define D_INTR_EOL 5 /* End of List */
481 #define D_INTR_CMDI 6 /* Command has bean read */
482 #define D_INTR_XCMP 8 /* Transmission of frame complete */
483 #define D_INTR_SBRI 9 /* BRI status change info */
484 #define D_INTR_FXDT 10 /* Fixed data change */
485 #define D_INTR_CHIL 11 /* CHI lost frame sync (channel 36 only) */
486 #define D_INTR_COLL 11 /* Unrecoverable D-Channel collision */
487 #define D_INTR_DBYT 12 /* Dropped by frame slip */
488 #define D_INTR_RBYT 13 /* Repeated by frame slip */
489 #define D_INTR_LINT 14 /* Lost Interrupt */
490 #define D_INTR_UNDR 15 /* DMA underrun */
494 #define D_INTR_CHI 36
495 #define D_INTR_CMD 38
497 #define D_INTR_GETCHAN(v) (((v) >> 24) & 0x3f)
498 #define D_INTR_GETCODE(v) (((v) >> 20) & 0xf)
499 #define D_INTR_GETCMD(v) (((v) >> 16) & 0xf)
500 #define D_INTR_GETVAL(v) ((v) & 0xffff)
501 #define D_INTR_GETRVAL(v) ((v) & 0xfffff)
503 #define D_P_0 0 /* TE receive anchor */
504 #define D_P_1 1 /* TE transmit anchor */
505 #define D_P_2 2 /* NT transmit anchor */
506 #define D_P_3 3 /* NT receive anchor */
507 #define D_P_4 4 /* CHI send data */
508 #define D_P_5 5 /* CHI receive data */
509 #define D_P_6 6 /* */
510 #define D_P_7 7 /* */
511 #define D_P_8 8 /* */
512 #define D_P_9 9 /* */
513 #define D_P_10 10 /* */
514 #define D_P_11 11 /* */
515 #define D_P_12 12 /* */
516 #define D_P_13 13 /* */
517 #define D_P_14 14 /* */
518 #define D_P_15 15 /* */
519 #define D_P_16 16 /* CHI anchor pipe */
520 #define D_P_17 17 /* CHI send */
521 #define D_P_18 18 /* CHI receive */
522 #define D_P_19 19 /* CHI receive */
523 #define D_P_20 20 /* CHI receive */
524 #define D_P_21 21 /* */
525 #define D_P_22 22 /* */
526 #define D_P_23 23 /* */
527 #define D_P_24 24 /* */
528 #define D_P_25 25 /* */
529 #define D_P_26 26 /* */
530 #define D_P_27 27 /* */
531 #define D_P_28 28 /* */
532 #define D_P_29 29 /* */
533 #define D_P_30 30 /* */
534 #define D_P_31 31 /* */
536 /* Transmit descriptor defines */
537 #define DBRI_TD_F (1 << 31) /* End of Frame */
538 #define DBRI_TD_D (1 << 30) /* Do not append CRC */
539 #define DBRI_TD_CNT(v) ((v) << 16) /* Number of valid bytes in the buffer */
540 #define DBRI_TD_B (1 << 15) /* Final interrupt */
541 #define DBRI_TD_M (1 << 14) /* Marker interrupt */
542 #define DBRI_TD_I (1 << 13) /* Transmit Idle Characters */
543 #define DBRI_TD_FCNT(v) (v) /* Flag Count */
544 #define DBRI_TD_UNR (1 << 3) /* Underrun: transmitter is out of data */
545 #define DBRI_TD_ABT (1 << 2) /* Abort: frame aborted */
546 #define DBRI_TD_TBC (1 << 0) /* Transmit buffer Complete */
547 #define DBRI_TD_STATUS(v) ((v) & 0xff) /* Transmit status */
548 /* Maximum buffer size per TD: almost 8KB */
549 #define DBRI_TD_MAXCNT ((1 << 13) - 4)
551 /* Receive descriptor defines */
552 #define DBRI_RD_F (1 << 31) /* End of Frame */
553 #define DBRI_RD_C (1 << 30) /* Completed buffer */
554 #define DBRI_RD_B (1 << 15) /* Final interrupt */
555 #define DBRI_RD_M (1 << 14) /* Marker interrupt */
556 #define DBRI_RD_BCNT(v) (v) /* Buffer size */
557 #define DBRI_RD_CRC (1 << 7) /* 0: CRC is correct */
558 #define DBRI_RD_BBC (1 << 6) /* 1: Bad Byte received */
559 #define DBRI_RD_ABT (1 << 5) /* Abort: frame aborted */
560 #define DBRI_RD_OVRN (1 << 3) /* Overrun: data lost */
561 #define DBRI_RD_STATUS(v) ((v) & 0xff) /* Receive status */
562 #define DBRI_RD_CNT(v) (((v) >> 16) & 0x1fff) /* Valid bytes in the buffer */
564 /* stream_info[] access */
565 /* Translate the ALSA direction into the array index */
566 #define DBRI_STREAMNO(substream) \
567 (substream->stream == \
568 SNDRV_PCM_STREAM_PLAYBACK? DBRI_PLAY: DBRI_REC)
570 /* Return a pointer to dbri_streaminfo */
571 #define DBRI_STREAM(dbri, substream) \
572 &dbri->stream_info[DBRI_STREAMNO(substream)]
574 static struct snd_dbri *dbri_list; /* All DBRI devices */
577 * Short data pipes transmit LSB first. The CS4215 receives MSB first. Grrr.
578 * So we have to reverse the bits. Note: not all bit lengths are supported
580 static __u32 reverse_bytes(__u32 b, int len)
584 b = ((b & 0xffff0000) >> 16) | ((b & 0x0000ffff) << 16);
586 b = ((b & 0xff00ff00) >> 8) | ((b & 0x00ff00ff) << 8);
588 b = ((b & 0xf0f0f0f0) >> 4) | ((b & 0x0f0f0f0f) << 4);
590 b = ((b & 0xcccccccc) >> 2) | ((b & 0x33333333) << 2);
592 b = ((b & 0xaaaaaaaa) >> 1) | ((b & 0x55555555) << 1);
597 printk(KERN_ERR "DBRI reverse_bytes: unsupported length\n");
604 ****************************************************************************
605 ************** DBRI initialization and command synchronization *************
606 ****************************************************************************
608 Commands are sent to the DBRI by building a list of them in memory,
609 then writing the address of the first list item to DBRI register 8.
610 The list is terminated with a WAIT command, which generates a
611 CPU interrupt to signal completion.
613 Since the DBRI can run in parallel with the CPU, several means of
614 synchronization present themselves. The method implemented here is only
615 use of the dbri_cmdwait() to wait for execution of batch of sent commands.
617 A circular command buffer is used here. A new command is being added
618 while another can be executed. The scheme works by adding two WAIT commands
619 after each sent batch of commands. When the next batch is prepared it is
620 added after the WAIT commands then the WAITs are replaced with single JUMP
621 command to the new batch. The the DBRI is forced to reread the last WAIT
622 command (replaced by the JUMP by then). If the DBRI is still executing
623 previous commands the request to reread the WAIT command is ignored.
625 Every time a routine wants to write commands to the DBRI, it must
626 first call dbri_cmdlock() and get pointer to a free space in
627 dbri->dma->cmd buffer. After this, the commands can be written to
628 the buffer, and dbri_cmdsend() is called with the final pointer value
629 to send them to the DBRI.
635 * Wait for the current command string to execute
637 static void dbri_cmdwait(struct snd_dbri *dbri)
639 int maxloops = MAXLOOPS;
642 /* Delay if previous commands are still being processed */
643 spin_lock_irqsave(&dbri->lock, flags);
644 while ((--maxloops) > 0 && (sbus_readl(dbri->regs + REG0) & D_P)) {
645 spin_unlock_irqrestore(&dbri->lock, flags);
646 msleep_interruptible(1);
647 spin_lock_irqsave(&dbri->lock, flags);
649 spin_unlock_irqrestore(&dbri->lock, flags);
652 printk(KERN_ERR "DBRI: Chip never completed command buffer\n");
654 dprintk(D_CMD, "Chip completed command buffer (%d)\n",
655 MAXLOOPS - maxloops - 1);
659 * Lock the command queue and returns pointer to a space for len cmd words
660 * It locks the cmdlock spinlock.
662 static s32 *dbri_cmdlock(struct snd_dbri *dbri, int len)
664 /* Space for 2 WAIT cmds (replaced later by 1 JUMP cmd) */
666 spin_lock(&dbri->cmdlock);
667 if (dbri->cmdptr - dbri->dma->cmd + len < DBRI_NO_CMDS - 2)
668 return dbri->cmdptr + 2;
669 else if (len < sbus_readl(dbri->regs + REG8) - dbri->dma_dvma)
670 return dbri->dma->cmd;
672 printk(KERN_ERR "DBRI: no space for commands.");
678 * Send prepared cmd string. It works by writing a JUMP cmd into
679 * the last WAIT cmd and force DBRI to reread the cmd.
680 * The JUMP cmd points to the new cmd string.
681 * It also releases the cmdlock spinlock.
683 * Lock must be held before calling this.
685 static void dbri_cmdsend(struct snd_dbri *dbri, s32 *cmd, int len)
688 static int wait_id = 0;
691 wait_id &= 0xffff; /* restrict it to a 16 bit counter. */
692 *(cmd) = DBRI_CMD(D_WAIT, 1, wait_id);
693 *(cmd+1) = DBRI_CMD(D_WAIT, 1, wait_id);
695 /* Replace the last command with JUMP */
696 addr = dbri->dma_dvma + (cmd - len - dbri->dma->cmd) * sizeof(s32);
697 *(dbri->cmdptr+1) = addr;
698 *(dbri->cmdptr) = DBRI_CMD(D_JUMP, 0, 0);
701 if (cmd > dbri->cmdptr) {
704 for (ptr = dbri->cmdptr; ptr < cmd+2; ptr++)
705 dprintk(D_CMD, "cmd: %lx:%08x\n",
706 (unsigned long)ptr, *ptr);
708 s32 *ptr = dbri->cmdptr;
710 dprintk(D_CMD, "cmd: %lx:%08x\n", (unsigned long)ptr, *ptr);
712 dprintk(D_CMD, "cmd: %lx:%08x\n", (unsigned long)ptr, *ptr);
713 for (ptr = dbri->dma->cmd; ptr < cmd+2; ptr++)
714 dprintk(D_CMD, "cmd: %lx:%08x\n",
715 (unsigned long)ptr, *ptr);
719 /* Reread the last command */
720 tmp = sbus_readl(dbri->regs + REG0);
722 sbus_writel(tmp, dbri->regs + REG0);
725 spin_unlock(&dbri->cmdlock);
728 /* Lock must be held when calling this */
729 static void dbri_reset(struct snd_dbri *dbri)
734 dprintk(D_GEN, "reset 0:%x 2:%x 8:%x 9:%x\n",
735 sbus_readl(dbri->regs + REG0),
736 sbus_readl(dbri->regs + REG2),
737 sbus_readl(dbri->regs + REG8), sbus_readl(dbri->regs + REG9));
739 sbus_writel(D_R, dbri->regs + REG0); /* Soft Reset */
740 for (i = 0; (sbus_readl(dbri->regs + REG0) & D_R) && i < 64; i++)
743 /* A brute approach - DBRI falls back to working burst size by itself
744 * On SS20 D_S does not work, so do not try so high. */
745 tmp = sbus_readl(dbri->regs + REG0);
748 sbus_writel(tmp, dbri->regs + REG0);
751 /* Lock must not be held before calling this */
752 static void dbri_initialize(struct snd_dbri *dbri)
759 spin_lock_irqsave(&dbri->lock, flags);
763 /* Initialize pipes */
764 for (n = 0; n < DBRI_NO_PIPES; n++)
765 dbri->pipes[n].desc = dbri->pipes[n].first_desc = -1;
767 spin_lock_init(&dbri->cmdlock);
769 * Initialize the interrupt ring buffer.
771 dma_addr = dbri->dma_dvma + dbri_dma_off(intr, 0);
772 dbri->dma->intr[0] = dma_addr;
775 * Set up the interrupt queue
777 spin_lock(&dbri->cmdlock);
778 cmd = dbri->cmdptr = dbri->dma->cmd;
779 *(cmd++) = DBRI_CMD(D_IIQ, 0, 0);
781 *(cmd++) = DBRI_CMD(D_PAUSE, 0, 0);
783 *(cmd++) = DBRI_CMD(D_WAIT, 1, 0);
784 *(cmd++) = DBRI_CMD(D_WAIT, 1, 0);
785 dma_addr = dbri->dma_dvma + dbri_dma_off(cmd, 0);
786 sbus_writel(dma_addr, dbri->regs + REG8);
787 spin_unlock(&dbri->cmdlock);
789 spin_unlock_irqrestore(&dbri->lock, flags);
794 ****************************************************************************
795 ************************** DBRI data pipe management ***********************
796 ****************************************************************************
798 While DBRI control functions use the command and interrupt buffers, the
799 main data path takes the form of data pipes, which can be short (command
800 and interrupt driven), or long (attached to DMA buffers). These functions
801 provide a rudimentary means of setting up and managing the DBRI's pipes,
802 but the calling functions have to make sure they respect the pipes' linked
803 list ordering, among other things. The transmit and receive functions
804 here interface closely with the transmit and receive interrupt code.
807 static int pipe_active(struct snd_dbri *dbri, int pipe)
809 return ((pipe >= 0) && (dbri->pipes[pipe].desc != -1));
812 /* reset_pipe(dbri, pipe)
814 * Called on an in-use pipe to clear anything being transmitted or received
815 * Lock must be held before calling this.
817 static void reset_pipe(struct snd_dbri *dbri, int pipe)
823 if (pipe < 0 || pipe > DBRI_MAX_PIPE) {
824 printk(KERN_ERR "DBRI: reset_pipe called with "
825 "illegal pipe number\n");
829 sdp = dbri->pipes[pipe].sdp;
831 printk(KERN_ERR "DBRI: reset_pipe called "
832 "on uninitialized pipe\n");
836 cmd = dbri_cmdlock(dbri, 3);
837 *(cmd++) = DBRI_CMD(D_SDP, 0, sdp | D_SDP_C | D_SDP_P);
839 *(cmd++) = DBRI_CMD(D_PAUSE, 0, 0);
840 dbri_cmdsend(dbri, cmd, 3);
842 desc = dbri->pipes[pipe].first_desc;
845 dbri->dma->desc[desc].ba = 0;
846 dbri->dma->desc[desc].nda = 0;
847 desc = dbri->next_desc[desc];
848 } while (desc != -1 && desc != dbri->pipes[pipe].first_desc);
850 dbri->pipes[pipe].desc = -1;
851 dbri->pipes[pipe].first_desc = -1;
855 * Lock must be held before calling this.
857 static void setup_pipe(struct snd_dbri *dbri, int pipe, int sdp)
859 if (pipe < 0 || pipe > DBRI_MAX_PIPE) {
860 printk(KERN_ERR "DBRI: setup_pipe called "
861 "with illegal pipe number\n");
865 if ((sdp & 0xf800) != sdp) {
866 printk(KERN_ERR "DBRI: setup_pipe called "
867 "with strange SDP value\n");
871 /* If this is a fixed receive pipe, arrange for an interrupt
872 * every time its data changes
874 if (D_SDP_MODE(sdp) == D_SDP_FIXED && !(sdp & D_SDP_TO_SER))
878 dbri->pipes[pipe].sdp = sdp;
879 dbri->pipes[pipe].desc = -1;
880 dbri->pipes[pipe].first_desc = -1;
882 reset_pipe(dbri, pipe);
886 * Lock must be held before calling this.
888 static void link_time_slot(struct snd_dbri *dbri, int pipe,
889 int prevpipe, int nextpipe,
890 int length, int cycle)
895 if (pipe < 0 || pipe > DBRI_MAX_PIPE
896 || prevpipe < 0 || prevpipe > DBRI_MAX_PIPE
897 || nextpipe < 0 || nextpipe > DBRI_MAX_PIPE) {
899 "DBRI: link_time_slot called with illegal pipe number\n");
903 if (dbri->pipes[pipe].sdp == 0
904 || dbri->pipes[prevpipe].sdp == 0
905 || dbri->pipes[nextpipe].sdp == 0) {
906 printk(KERN_ERR "DBRI: link_time_slot called "
907 "on uninitialized pipe\n");
911 dbri->pipes[prevpipe].nextpipe = pipe;
912 dbri->pipes[pipe].nextpipe = nextpipe;
913 dbri->pipes[pipe].length = length;
915 cmd = dbri_cmdlock(dbri, 4);
917 if (dbri->pipes[pipe].sdp & D_SDP_TO_SER) {
918 /* Deal with CHI special case:
919 * "If transmission on edges 0 or 1 is desired, then cycle n
920 * (where n = # of bit times per frame...) must be used."
921 * - DBRI data sheet, page 11
923 if (prevpipe == 16 && cycle == 0)
924 cycle = dbri->chi_bpf;
926 val = D_DTS_VO | D_DTS_INS | D_DTS_PRVOUT(prevpipe) | pipe;
927 *(cmd++) = DBRI_CMD(D_DTS, 0, val);
930 D_TS_LEN(length) | D_TS_CYCLE(cycle) | D_TS_NEXT(nextpipe);
932 val = D_DTS_VI | D_DTS_INS | D_DTS_PRVIN(prevpipe) | pipe;
933 *(cmd++) = DBRI_CMD(D_DTS, 0, val);
935 D_TS_LEN(length) | D_TS_CYCLE(cycle) | D_TS_NEXT(nextpipe);
938 *(cmd++) = DBRI_CMD(D_PAUSE, 0, 0);
940 dbri_cmdsend(dbri, cmd, 4);
945 * Lock must be held before calling this.
947 static void unlink_time_slot(struct snd_dbri *dbri, int pipe,
948 enum in_or_out direction, int prevpipe,
954 if (pipe < 0 || pipe > DBRI_MAX_PIPE
955 || prevpipe < 0 || prevpipe > DBRI_MAX_PIPE
956 || nextpipe < 0 || nextpipe > DBRI_MAX_PIPE) {
958 "DBRI: unlink_time_slot called with illegal pipe number\n");
962 cmd = dbri_cmdlock(dbri, 4);
964 if (direction == PIPEinput) {
965 val = D_DTS_VI | D_DTS_DEL | D_DTS_PRVIN(prevpipe) | pipe;
966 *(cmd++) = DBRI_CMD(D_DTS, 0, val);
967 *(cmd++) = D_TS_NEXT(nextpipe);
970 val = D_DTS_VO | D_DTS_DEL | D_DTS_PRVOUT(prevpipe) | pipe;
971 *(cmd++) = DBRI_CMD(D_DTS, 0, val);
973 *(cmd++) = D_TS_NEXT(nextpipe);
975 *(cmd++) = DBRI_CMD(D_PAUSE, 0, 0);
977 dbri_cmdsend(dbri, cmd, 4);
981 /* xmit_fixed() / recv_fixed()
983 * Transmit/receive data on a "fixed" pipe - i.e, one whose contents are not
984 * expected to change much, and which we don't need to buffer.
985 * The DBRI only interrupts us when the data changes (receive pipes),
986 * or only changes the data when this function is called (transmit pipes).
987 * Only short pipes (numbers 16-31) can be used in fixed data mode.
989 * These function operate on a 32-bit field, no matter how large
990 * the actual time slot is. The interrupt handler takes care of bit
991 * ordering and alignment. An 8-bit time slot will always end up
992 * in the low-order 8 bits, filled either MSB-first or LSB-first,
993 * depending on the settings passed to setup_pipe().
995 * Lock must not be held before calling it.
997 static void xmit_fixed(struct snd_dbri *dbri, int pipe, unsigned int data)
1000 unsigned long flags;
1002 if (pipe < 16 || pipe > DBRI_MAX_PIPE) {
1003 printk(KERN_ERR "DBRI: xmit_fixed: Illegal pipe number\n");
1007 if (D_SDP_MODE(dbri->pipes[pipe].sdp) == 0) {
1008 printk(KERN_ERR "DBRI: xmit_fixed: "
1009 "Uninitialized pipe %d\n", pipe);
1013 if (D_SDP_MODE(dbri->pipes[pipe].sdp) != D_SDP_FIXED) {
1014 printk(KERN_ERR "DBRI: xmit_fixed: Non-fixed pipe %d\n", pipe);
1018 if (!(dbri->pipes[pipe].sdp & D_SDP_TO_SER)) {
1019 printk(KERN_ERR "DBRI: xmit_fixed: Called on receive pipe %d\n",
1024 /* DBRI short pipes always transmit LSB first */
1026 if (dbri->pipes[pipe].sdp & D_SDP_MSB)
1027 data = reverse_bytes(data, dbri->pipes[pipe].length);
1029 cmd = dbri_cmdlock(dbri, 3);
1031 *(cmd++) = DBRI_CMD(D_SSP, 0, pipe);
1033 *(cmd++) = DBRI_CMD(D_PAUSE, 0, 0);
1035 spin_lock_irqsave(&dbri->lock, flags);
1036 dbri_cmdsend(dbri, cmd, 3);
1037 spin_unlock_irqrestore(&dbri->lock, flags);
1042 static void recv_fixed(struct snd_dbri *dbri, int pipe, volatile __u32 *ptr)
1044 if (pipe < 16 || pipe > DBRI_MAX_PIPE) {
1045 printk(KERN_ERR "DBRI: recv_fixed called with "
1046 "illegal pipe number\n");
1050 if (D_SDP_MODE(dbri->pipes[pipe].sdp) != D_SDP_FIXED) {
1051 printk(KERN_ERR "DBRI: recv_fixed called on "
1052 "non-fixed pipe %d\n", pipe);
1056 if (dbri->pipes[pipe].sdp & D_SDP_TO_SER) {
1057 printk(KERN_ERR "DBRI: recv_fixed called on "
1058 "transmit pipe %d\n", pipe);
1062 dbri->pipes[pipe].recv_fixed_ptr = ptr;
1067 * Setup transmit/receive data on a "long" pipe - i.e, one associated
1068 * with a DMA buffer.
1070 * Only pipe numbers 0-15 can be used in this mode.
1072 * This function takes a stream number pointing to a data buffer,
1073 * and work by building chains of descriptors which identify the
1074 * data buffers. Buffers too large for a single descriptor will
1075 * be spread across multiple descriptors.
1077 * All descriptors create a ring buffer.
1079 * Lock must be held before calling this.
1081 static int setup_descs(struct snd_dbri *dbri, int streamno, unsigned int period)
1083 struct dbri_streaminfo *info = &dbri->stream_info[streamno];
1087 int first_desc = -1;
1090 if (info->pipe < 0 || info->pipe > 15) {
1091 printk(KERN_ERR "DBRI: setup_descs: Illegal pipe number\n");
1095 if (dbri->pipes[info->pipe].sdp == 0) {
1096 printk(KERN_ERR "DBRI: setup_descs: Uninitialized pipe %d\n",
1101 dvma_buffer = info->dvma_buffer;
1104 if (streamno == DBRI_PLAY) {
1105 if (!(dbri->pipes[info->pipe].sdp & D_SDP_TO_SER)) {
1106 printk(KERN_ERR "DBRI: setup_descs: "
1107 "Called on receive pipe %d\n", info->pipe);
1111 if (dbri->pipes[info->pipe].sdp & D_SDP_TO_SER) {
1113 "DBRI: setup_descs: Called on transmit pipe %d\n",
1117 /* Should be able to queue multiple buffers
1118 * to receive on a pipe
1120 if (pipe_active(dbri, info->pipe)) {
1121 printk(KERN_ERR "DBRI: recv_on_pipe: "
1122 "Called on active pipe %d\n", info->pipe);
1126 /* Make sure buffer size is multiple of four */
1130 /* Free descriptors if pipe has any */
1131 desc = dbri->pipes[info->pipe].first_desc;
1134 dbri->dma->desc[desc].ba = 0;
1135 dbri->dma->desc[desc].nda = 0;
1136 desc = dbri->next_desc[desc];
1137 } while (desc != -1 &&
1138 desc != dbri->pipes[info->pipe].first_desc);
1140 dbri->pipes[info->pipe].desc = -1;
1141 dbri->pipes[info->pipe].first_desc = -1;
1147 for (; desc < DBRI_NO_DESCS; desc++) {
1148 if (!dbri->dma->desc[desc].ba)
1151 if (desc == DBRI_NO_DESCS) {
1152 printk(KERN_ERR "DBRI: setup_descs: No descriptors\n");
1156 if (len > DBRI_TD_MAXCNT)
1157 mylen = DBRI_TD_MAXCNT; /* 8KB - 4 */
1164 dbri->next_desc[desc] = -1;
1165 dbri->dma->desc[desc].ba = dvma_buffer;
1166 dbri->dma->desc[desc].nda = 0;
1168 if (streamno == DBRI_PLAY) {
1169 dbri->dma->desc[desc].word1 = DBRI_TD_CNT(mylen);
1170 dbri->dma->desc[desc].word4 = 0;
1171 dbri->dma->desc[desc].word1 |= DBRI_TD_F | DBRI_TD_B;
1173 dbri->dma->desc[desc].word1 = 0;
1174 dbri->dma->desc[desc].word4 =
1175 DBRI_RD_B | DBRI_RD_BCNT(mylen);
1178 if (first_desc == -1)
1181 dbri->next_desc[last_desc] = desc;
1182 dbri->dma->desc[last_desc].nda =
1183 dbri->dma_dvma + dbri_dma_off(desc, desc);
1187 dvma_buffer += mylen;
1191 if (first_desc == -1 || last_desc == -1) {
1192 printk(KERN_ERR "DBRI: setup_descs: "
1193 " Not enough descriptors available\n");
1197 dbri->dma->desc[last_desc].nda =
1198 dbri->dma_dvma + dbri_dma_off(desc, first_desc);
1199 dbri->next_desc[last_desc] = first_desc;
1200 dbri->pipes[info->pipe].first_desc = first_desc;
1201 dbri->pipes[info->pipe].desc = first_desc;
1204 for (desc = first_desc; desc != -1;) {
1205 dprintk(D_DESC, "DESC %d: %08x %08x %08x %08x\n",
1207 dbri->dma->desc[desc].word1,
1208 dbri->dma->desc[desc].ba,
1209 dbri->dma->desc[desc].nda, dbri->dma->desc[desc].word4);
1210 desc = dbri->next_desc[desc];
1211 if (desc == first_desc)
1219 ****************************************************************************
1220 ************************** DBRI - CHI interface ****************************
1221 ****************************************************************************
1223 The CHI is a four-wire (clock, frame sync, data in, data out) time-division
1224 multiplexed serial interface which the DBRI can operate in either master
1225 (give clock/frame sync) or slave (take clock/frame sync) mode.
1229 enum master_or_slave { CHImaster, CHIslave };
1232 * Lock must not be held before calling it.
1234 static void reset_chi(struct snd_dbri *dbri,
1235 enum master_or_slave master_or_slave,
1241 /* Set CHI Anchor: Pipe 16 */
1243 cmd = dbri_cmdlock(dbri, 4);
1244 val = D_DTS_VO | D_DTS_VI | D_DTS_INS
1245 | D_DTS_PRVIN(16) | D_PIPE(16) | D_DTS_PRVOUT(16);
1246 *(cmd++) = DBRI_CMD(D_DTS, 0, val);
1247 *(cmd++) = D_TS_ANCHOR | D_TS_NEXT(16);
1248 *(cmd++) = D_TS_ANCHOR | D_TS_NEXT(16);
1249 *(cmd++) = DBRI_CMD(D_PAUSE, 0, 0);
1250 dbri_cmdsend(dbri, cmd, 4);
1252 dbri->pipes[16].sdp = 1;
1253 dbri->pipes[16].nextpipe = 16;
1255 cmd = dbri_cmdlock(dbri, 4);
1257 if (master_or_slave == CHIslave) {
1258 /* Setup DBRI for CHI Slave - receive clock, frame sync (FS)
1260 * CHICM = 0 (slave mode, 8 kHz frame rate)
1261 * IR = give immediate CHI status interrupt
1262 * EN = give CHI status interrupt upon change
1264 *(cmd++) = DBRI_CMD(D_CHI, 0, D_CHI_CHICM(0));
1266 /* Setup DBRI for CHI Master - generate clock, FS
1268 * BPF = bits per 8 kHz frame
1269 * 12.288 MHz / CHICM_divisor = clock rate
1270 * FD = 1 - drive CHIFS on rising edge of CHICK
1272 int clockrate = bits_per_frame * 8;
1273 int divisor = 12288 / clockrate;
1275 if (divisor > 255 || divisor * clockrate != 12288)
1276 printk(KERN_ERR "DBRI: illegal bits_per_frame "
1279 *(cmd++) = DBRI_CMD(D_CHI, 0, D_CHI_CHICM(divisor) | D_CHI_FD
1280 | D_CHI_BPF(bits_per_frame));
1283 dbri->chi_bpf = bits_per_frame;
1287 * RCE = 0 - receive on falling edge of CHICK
1288 * XCE = 1 - transmit on rising edge of CHICK
1289 * XEN = 1 - enable transmitter
1290 * REN = 1 - enable receiver
1293 *(cmd++) = DBRI_CMD(D_PAUSE, 0, 0);
1294 *(cmd++) = DBRI_CMD(D_CDM, 0, D_CDM_XCE | D_CDM_XEN | D_CDM_REN);
1295 *(cmd++) = DBRI_CMD(D_PAUSE, 0, 0);
1297 dbri_cmdsend(dbri, cmd, 4);
1301 ****************************************************************************
1302 *********************** CS4215 audio codec management **********************
1303 ****************************************************************************
1305 In the standard SPARC audio configuration, the CS4215 codec is attached
1306 to the DBRI via the CHI interface and few of the DBRI's PIO pins.
1308 * Lock must not be held before calling it.
1311 static void cs4215_setup_pipes(struct snd_dbri *dbri)
1313 unsigned long flags;
1315 spin_lock_irqsave(&dbri->lock, flags);
1318 * Pipe 4: Send timeslots 1-4 (audio data)
1319 * Pipe 20: Send timeslots 5-8 (part of ctrl data)
1320 * Pipe 6: Receive timeslots 1-4 (audio data)
1321 * Pipe 21: Receive timeslots 6-7. We can only receive 20 bits via
1322 * interrupt, and the rest of the data (slot 5 and 8) is
1323 * not relevant for us (only for doublechecking).
1326 * Pipe 17: Send timeslots 1-4 (slots 5-8 are read only)
1327 * Pipe 18: Receive timeslot 1 (clb).
1328 * Pipe 19: Receive timeslot 7 (version).
1331 setup_pipe(dbri, 4, D_SDP_MEM | D_SDP_TO_SER | D_SDP_MSB);
1332 setup_pipe(dbri, 20, D_SDP_FIXED | D_SDP_TO_SER | D_SDP_MSB);
1333 setup_pipe(dbri, 6, D_SDP_MEM | D_SDP_FROM_SER | D_SDP_MSB);
1334 setup_pipe(dbri, 21, D_SDP_FIXED | D_SDP_FROM_SER | D_SDP_MSB);
1336 setup_pipe(dbri, 17, D_SDP_FIXED | D_SDP_TO_SER | D_SDP_MSB);
1337 setup_pipe(dbri, 18, D_SDP_FIXED | D_SDP_FROM_SER | D_SDP_MSB);
1338 setup_pipe(dbri, 19, D_SDP_FIXED | D_SDP_FROM_SER | D_SDP_MSB);
1339 spin_unlock_irqrestore(&dbri->lock, flags);
1344 static int cs4215_init_data(struct cs4215 *mm)
1347 * No action, memory resetting only.
1349 * Data Time Slot 5-8
1350 * Speaker,Line and Headphone enable. Gain set to the half.
1353 mm->data[0] = CS4215_LO(0x20) | CS4215_HE | CS4215_LE;
1354 mm->data[1] = CS4215_RO(0x20) | CS4215_SE;
1355 mm->data[2] = CS4215_LG(0x8) | CS4215_IS | CS4215_PIO0 | CS4215_PIO1;
1356 mm->data[3] = CS4215_RG(0x8) | CS4215_MA(0xf);
1359 * Control Time Slot 1-4
1360 * 0: Default I/O voltage scale
1361 * 1: 8 bit ulaw, 8kHz, mono, high pass filter disabled
1362 * 2: Serial enable, CHI master, 128 bits per frame, clock 1
1365 mm->ctrl[0] = CS4215_RSRVD_1 | CS4215_MLB;
1366 mm->ctrl[1] = CS4215_DFR_ULAW | CS4215_FREQ[0].csval;
1367 mm->ctrl[2] = CS4215_XCLK | CS4215_BSEL_128 | CS4215_FREQ[0].xtal;
1372 mm->precision = 8; /* For ULAW */
1378 static void cs4215_setdata(struct snd_dbri *dbri, int muted)
1381 dbri->mm.data[0] |= 63;
1382 dbri->mm.data[1] |= 63;
1383 dbri->mm.data[2] &= ~15;
1384 dbri->mm.data[3] &= ~15;
1386 /* Start by setting the playback attenuation. */
1387 struct dbri_streaminfo *info = &dbri->stream_info[DBRI_PLAY];
1388 int left_gain = info->left_gain & 0x3f;
1389 int right_gain = info->right_gain & 0x3f;
1391 dbri->mm.data[0] &= ~0x3f; /* Reset the volume bits */
1392 dbri->mm.data[1] &= ~0x3f;
1393 dbri->mm.data[0] |= (DBRI_MAX_VOLUME - left_gain);
1394 dbri->mm.data[1] |= (DBRI_MAX_VOLUME - right_gain);
1396 /* Now set the recording gain. */
1397 info = &dbri->stream_info[DBRI_REC];
1398 left_gain = info->left_gain & 0xf;
1399 right_gain = info->right_gain & 0xf;
1400 dbri->mm.data[2] |= CS4215_LG(left_gain);
1401 dbri->mm.data[3] |= CS4215_RG(right_gain);
1404 xmit_fixed(dbri, 20, *(int *)dbri->mm.data);
1408 * Set the CS4215 to data mode.
1410 static void cs4215_open(struct snd_dbri *dbri)
1414 unsigned long flags;
1416 dprintk(D_MM, "cs4215_open: %d channels, %d bits\n",
1417 dbri->mm.channels, dbri->mm.precision);
1419 /* Temporarily mute outputs, and wait 1/8000 sec (125 us)
1420 * to make sure this takes. This avoids clicking noises.
1423 cs4215_setdata(dbri, 1);
1428 * Pipe 4: Send timeslots 1-4 (audio data)
1429 * Pipe 20: Send timeslots 5-8 (part of ctrl data)
1430 * Pipe 6: Receive timeslots 1-4 (audio data)
1431 * Pipe 21: Receive timeslots 6-7. We can only receive 20 bits via
1432 * interrupt, and the rest of the data (slot 5 and 8) is
1433 * not relevant for us (only for doublechecking).
1435 * Just like in control mode, the time slots are all offset by eight
1436 * bits. The CS4215, it seems, observes TSIN (the delayed signal)
1437 * even if it's the CHI master. Don't ask me...
1439 spin_lock_irqsave(&dbri->lock, flags);
1440 tmp = sbus_readl(dbri->regs + REG0);
1441 tmp &= ~(D_C); /* Disable CHI */
1442 sbus_writel(tmp, dbri->regs + REG0);
1444 /* Switch CS4215 to data mode - set PIO3 to 1 */
1445 sbus_writel(D_ENPIO | D_PIO1 | D_PIO3 |
1446 (dbri->mm.onboard ? D_PIO0 : D_PIO2), dbri->regs + REG2);
1448 reset_chi(dbri, CHIslave, 128);
1450 /* Note: this next doesn't work for 8-bit stereo, because the two
1451 * channels would be on timeslots 1 and 3, with 2 and 4 idle.
1452 * (See CS4215 datasheet Fig 15)
1454 * DBRI non-contiguous mode would be required to make this work.
1456 data_width = dbri->mm.channels * dbri->mm.precision;
1458 link_time_slot(dbri, 4, 16, 16, data_width, dbri->mm.offset);
1459 link_time_slot(dbri, 20, 4, 16, 32, dbri->mm.offset + 32);
1460 link_time_slot(dbri, 6, 16, 16, data_width, dbri->mm.offset);
1461 link_time_slot(dbri, 21, 6, 16, 16, dbri->mm.offset + 40);
1463 /* FIXME: enable CHI after _setdata? */
1464 tmp = sbus_readl(dbri->regs + REG0);
1465 tmp |= D_C; /* Enable CHI */
1466 sbus_writel(tmp, dbri->regs + REG0);
1467 spin_unlock_irqrestore(&dbri->lock, flags);
1469 cs4215_setdata(dbri, 0);
1473 * Send the control information (i.e. audio format)
1475 static int cs4215_setctrl(struct snd_dbri *dbri)
1479 unsigned long flags;
1481 /* FIXME - let the CPU do something useful during these delays */
1483 /* Temporarily mute outputs, and wait 1/8000 sec (125 us)
1484 * to make sure this takes. This avoids clicking noises.
1486 cs4215_setdata(dbri, 1);
1490 * Enable Control mode: Set DBRI's PIO3 (4215's D/~C) to 0, then wait
1491 * 12 cycles <= 12/(5512.5*64) sec = 34.01 usec
1493 val = D_ENPIO | D_PIO1 | (dbri->mm.onboard ? D_PIO0 : D_PIO2);
1494 sbus_writel(val, dbri->regs + REG2);
1495 dprintk(D_MM, "cs4215_setctrl: reg2=0x%x\n", val);
1498 /* In Control mode, the CS4215 is a slave device, so the DBRI must
1499 * operate as CHI master, supplying clocking and frame synchronization.
1501 * In Data mode, however, the CS4215 must be CHI master to insure
1502 * that its data stream is synchronous with its codec.
1504 * The upshot of all this? We start by putting the DBRI into master
1505 * mode, program the CS4215 in Control mode, then switch the CS4215
1506 * into Data mode and put the DBRI into slave mode. Various timing
1507 * requirements must be observed along the way.
1509 * Oh, and one more thing, on a SPARCStation 20 (and maybe
1510 * others?), the addressing of the CS4215's time slots is
1511 * offset by eight bits, so we add eight to all the "cycle"
1512 * values in the Define Time Slot (DTS) commands. This is
1513 * done in hardware by a TI 248 that delays the DBRI->4215
1514 * frame sync signal by eight clock cycles. Anybody know why?
1516 spin_lock_irqsave(&dbri->lock, flags);
1517 tmp = sbus_readl(dbri->regs + REG0);
1518 tmp &= ~D_C; /* Disable CHI */
1519 sbus_writel(tmp, dbri->regs + REG0);
1521 reset_chi(dbri, CHImaster, 128);
1525 * Pipe 17: Send timeslots 1-4 (slots 5-8 are read only)
1526 * Pipe 18: Receive timeslot 1 (clb).
1527 * Pipe 19: Receive timeslot 7 (version).
1530 link_time_slot(dbri, 17, 16, 16, 32, dbri->mm.offset);
1531 link_time_slot(dbri, 18, 16, 16, 8, dbri->mm.offset);
1532 link_time_slot(dbri, 19, 18, 16, 8, dbri->mm.offset + 48);
1533 spin_unlock_irqrestore(&dbri->lock, flags);
1535 /* Wait for the chip to echo back CLB (Control Latch Bit) as zero */
1536 dbri->mm.ctrl[0] &= ~CS4215_CLB;
1537 xmit_fixed(dbri, 17, *(int *)dbri->mm.ctrl);
1539 spin_lock_irqsave(&dbri->lock, flags);
1540 tmp = sbus_readl(dbri->regs + REG0);
1541 tmp |= D_C; /* Enable CHI */
1542 sbus_writel(tmp, dbri->regs + REG0);
1543 spin_unlock_irqrestore(&dbri->lock, flags);
1545 for (i = 10; ((dbri->mm.status & 0xe4) != 0x20); --i)
1546 msleep_interruptible(1);
1549 dprintk(D_MM, "CS4215 didn't respond to CLB (0x%02x)\n",
1554 /* Disable changes to our copy of the version number, as we are about
1555 * to leave control mode.
1557 recv_fixed(dbri, 19, NULL);
1559 /* Terminate CS4215 control mode - data sheet says
1560 * "Set CLB=1 and send two more frames of valid control info"
1562 dbri->mm.ctrl[0] |= CS4215_CLB;
1563 xmit_fixed(dbri, 17, *(int *)dbri->mm.ctrl);
1565 /* Two frames of control info @ 8kHz frame rate = 250 us delay */
1568 cs4215_setdata(dbri, 0);
1574 * Setup the codec with the sampling rate, audio format and number of
1576 * As part of the process we resend the settings for the data
1577 * timeslots as well.
1579 static int cs4215_prepare(struct snd_dbri *dbri, unsigned int rate,
1580 snd_pcm_format_t format, unsigned int channels)
1585 /* Lookup index for this rate */
1586 for (freq_idx = 0; CS4215_FREQ[freq_idx].freq != 0; freq_idx++) {
1587 if (CS4215_FREQ[freq_idx].freq == rate)
1590 if (CS4215_FREQ[freq_idx].freq != rate) {
1591 printk(KERN_WARNING "DBRI: Unsupported rate %d Hz\n", rate);
1596 case SNDRV_PCM_FORMAT_MU_LAW:
1597 dbri->mm.ctrl[1] = CS4215_DFR_ULAW;
1598 dbri->mm.precision = 8;
1600 case SNDRV_PCM_FORMAT_A_LAW:
1601 dbri->mm.ctrl[1] = CS4215_DFR_ALAW;
1602 dbri->mm.precision = 8;
1604 case SNDRV_PCM_FORMAT_U8:
1605 dbri->mm.ctrl[1] = CS4215_DFR_LINEAR8;
1606 dbri->mm.precision = 8;
1608 case SNDRV_PCM_FORMAT_S16_BE:
1609 dbri->mm.ctrl[1] = CS4215_DFR_LINEAR16;
1610 dbri->mm.precision = 16;
1613 printk(KERN_WARNING "DBRI: Unsupported format %d\n", format);
1617 /* Add rate parameters */
1618 dbri->mm.ctrl[1] |= CS4215_FREQ[freq_idx].csval;
1619 dbri->mm.ctrl[2] = CS4215_XCLK |
1620 CS4215_BSEL_128 | CS4215_FREQ[freq_idx].xtal;
1622 dbri->mm.channels = channels;
1624 dbri->mm.ctrl[1] |= CS4215_DFR_STEREO;
1626 ret = cs4215_setctrl(dbri);
1628 cs4215_open(dbri); /* set codec to data mode */
1636 static int cs4215_init(struct snd_dbri *dbri)
1638 u32 reg2 = sbus_readl(dbri->regs + REG2);
1639 dprintk(D_MM, "cs4215_init: reg2=0x%x\n", reg2);
1641 /* Look for the cs4215 chips */
1642 if (reg2 & D_PIO2) {
1643 dprintk(D_MM, "Onboard CS4215 detected\n");
1644 dbri->mm.onboard = 1;
1646 if (reg2 & D_PIO0) {
1647 dprintk(D_MM, "Speakerbox detected\n");
1648 dbri->mm.onboard = 0;
1650 if (reg2 & D_PIO2) {
1651 printk(KERN_INFO "DBRI: Using speakerbox / "
1652 "ignoring onboard mmcodec.\n");
1653 sbus_writel(D_ENPIO2, dbri->regs + REG2);
1657 if (!(reg2 & (D_PIO0 | D_PIO2))) {
1658 printk(KERN_ERR "DBRI: no mmcodec found.\n");
1662 cs4215_setup_pipes(dbri);
1663 cs4215_init_data(&dbri->mm);
1665 /* Enable capture of the status & version timeslots. */
1666 recv_fixed(dbri, 18, &dbri->mm.status);
1667 recv_fixed(dbri, 19, &dbri->mm.version);
1669 dbri->mm.offset = dbri->mm.onboard ? 0 : 8;
1670 if (cs4215_setctrl(dbri) == -1 || dbri->mm.version == 0xff) {
1671 dprintk(D_MM, "CS4215 failed probe at offset %d\n",
1675 dprintk(D_MM, "Found CS4215 at offset %d\n", dbri->mm.offset);
1681 ****************************************************************************
1682 *************************** DBRI interrupt handler *************************
1683 ****************************************************************************
1685 The DBRI communicates with the CPU mainly via a circular interrupt
1686 buffer. When an interrupt is signaled, the CPU walks through the
1687 buffer and calls dbri_process_one_interrupt() for each interrupt word.
1688 Complicated interrupts are handled by dedicated functions (which
1689 appear first in this file). Any pending interrupts can be serviced by
1690 calling dbri_process_interrupt_buffer(), which works even if the CPU's
1691 interrupts are disabled.
1697 * Starts transmitting the current TD's for recording/playing.
1698 * For playback, ALSA has filled the DMA memory with new data (we hope).
1700 static void xmit_descs(struct snd_dbri *dbri)
1702 struct dbri_streaminfo *info;
1704 unsigned long flags;
1708 return; /* Disabled */
1710 info = &dbri->stream_info[DBRI_REC];
1711 spin_lock_irqsave(&dbri->lock, flags);
1713 if (info->pipe >= 0) {
1714 first_td = dbri->pipes[info->pipe].first_desc;
1716 dprintk(D_DESC, "xmit_descs rec @ TD %d\n", first_td);
1718 /* Stream could be closed by the time we run. */
1719 if (first_td >= 0) {
1720 cmd = dbri_cmdlock(dbri, 2);
1721 *(cmd++) = DBRI_CMD(D_SDP, 0,
1722 dbri->pipes[info->pipe].sdp
1723 | D_SDP_P | D_SDP_EVERY | D_SDP_C);
1724 *(cmd++) = dbri->dma_dvma +
1725 dbri_dma_off(desc, first_td);
1726 dbri_cmdsend(dbri, cmd, 2);
1728 /* Reset our admin of the pipe. */
1729 dbri->pipes[info->pipe].desc = first_td;
1733 info = &dbri->stream_info[DBRI_PLAY];
1735 if (info->pipe >= 0) {
1736 first_td = dbri->pipes[info->pipe].first_desc;
1738 dprintk(D_DESC, "xmit_descs play @ TD %d\n", first_td);
1740 /* Stream could be closed by the time we run. */
1741 if (first_td >= 0) {
1742 cmd = dbri_cmdlock(dbri, 2);
1743 *(cmd++) = DBRI_CMD(D_SDP, 0,
1744 dbri->pipes[info->pipe].sdp
1745 | D_SDP_P | D_SDP_EVERY | D_SDP_C);
1746 *(cmd++) = dbri->dma_dvma +
1747 dbri_dma_off(desc, first_td);
1748 dbri_cmdsend(dbri, cmd, 2);
1750 /* Reset our admin of the pipe. */
1751 dbri->pipes[info->pipe].desc = first_td;
1755 spin_unlock_irqrestore(&dbri->lock, flags);
1758 /* transmission_complete_intr()
1760 * Called by main interrupt handler when DBRI signals transmission complete
1761 * on a pipe (interrupt triggered by the B bit in a transmit descriptor).
1763 * Walks through the pipe's list of transmit buffer descriptors and marks
1764 * them as available. Stops when the first descriptor is found without
1765 * TBC (Transmit Buffer Complete) set, or we've run through them all.
1767 * The DMA buffers are not released. They form a ring buffer and
1768 * they are filled by ALSA while others are transmitted by DMA.
1772 static void transmission_complete_intr(struct snd_dbri *dbri, int pipe)
1774 struct dbri_streaminfo *info;
1778 info = &dbri->stream_info[DBRI_PLAY];
1780 td = dbri->pipes[pipe].desc;
1782 if (td >= DBRI_NO_DESCS) {
1783 printk(KERN_ERR "DBRI: invalid td on pipe %d\n", pipe);
1787 status = DBRI_TD_STATUS(dbri->dma->desc[td].word4);
1788 if (!(status & DBRI_TD_TBC))
1791 dprintk(D_INT, "TD %d, status 0x%02x\n", td, status);
1793 dbri->dma->desc[td].word4 = 0; /* Reset it for next time. */
1794 info->offset += DBRI_RD_CNT(dbri->dma->desc[td].word1);
1796 td = dbri->next_desc[td];
1797 dbri->pipes[pipe].desc = td;
1801 if (spin_is_locked(&dbri->lock)) {
1802 spin_unlock(&dbri->lock);
1803 snd_pcm_period_elapsed(info->substream);
1804 spin_lock(&dbri->lock);
1806 snd_pcm_period_elapsed(info->substream);
1809 static void reception_complete_intr(struct snd_dbri *dbri, int pipe)
1811 struct dbri_streaminfo *info;
1812 int rd = dbri->pipes[pipe].desc;
1815 if (rd < 0 || rd >= DBRI_NO_DESCS) {
1816 printk(KERN_ERR "DBRI: invalid rd on pipe %d\n", pipe);
1820 dbri->pipes[pipe].desc = dbri->next_desc[rd];
1821 status = dbri->dma->desc[rd].word1;
1822 dbri->dma->desc[rd].word1 = 0; /* Reset it for next time. */
1824 info = &dbri->stream_info[DBRI_REC];
1825 info->offset += DBRI_RD_CNT(status);
1827 /* FIXME: Check status */
1829 dprintk(D_INT, "Recv RD %d, status 0x%02x, len %d\n",
1830 rd, DBRI_RD_STATUS(status), DBRI_RD_CNT(status));
1833 if (spin_is_locked(&dbri->lock)) {
1834 spin_unlock(&dbri->lock);
1835 snd_pcm_period_elapsed(info->substream);
1836 spin_lock(&dbri->lock);
1838 snd_pcm_period_elapsed(info->substream);
1841 static void dbri_process_one_interrupt(struct snd_dbri *dbri, int x)
1843 int val = D_INTR_GETVAL(x);
1844 int channel = D_INTR_GETCHAN(x);
1845 int command = D_INTR_GETCMD(x);
1846 int code = D_INTR_GETCODE(x);
1848 int rval = D_INTR_GETRVAL(x);
1851 if (channel == D_INTR_CMD) {
1852 dprintk(D_CMD, "INTR: Command: %-5s Value:%d\n",
1853 cmds[command], val);
1855 dprintk(D_INT, "INTR: Chan:%d Code:%d Val:%#x\n",
1856 channel, code, rval);
1861 if (command != D_WAIT)
1862 printk(KERN_ERR "DBRI: Command read interrupt\n");
1865 reception_complete_intr(dbri, channel);
1869 transmission_complete_intr(dbri, channel);
1872 /* UNDR - Transmission underrun
1873 * resend SDP command with clear pipe bit (C) set
1876 /* FIXME: do something useful in case of underrun */
1877 printk(KERN_ERR "DBRI: Underrun error\n");
1881 int td = dbri->pipes[pipe].desc;
1883 dbri->dma->desc[td].word4 = 0;
1884 cmd = dbri_cmdlock(dbri, NoGetLock);
1885 *(cmd++) = DBRI_CMD(D_SDP, 0,
1886 dbri->pipes[pipe].sdp
1887 | D_SDP_P | D_SDP_C | D_SDP_2SAME);
1888 *(cmd++) = dbri->dma_dvma + dbri_dma_off(desc, td);
1889 dbri_cmdsend(dbri, cmd);
1894 /* FXDT - Fixed data change */
1895 if (dbri->pipes[channel].sdp & D_SDP_MSB)
1896 val = reverse_bytes(val, dbri->pipes[channel].length);
1898 if (dbri->pipes[channel].recv_fixed_ptr)
1899 *(dbri->pipes[channel].recv_fixed_ptr) = val;
1902 if (channel != D_INTR_CMD)
1904 "DBRI: Ignored Interrupt: %d (0x%x)\n", code, x);
1908 /* dbri_process_interrupt_buffer advances through the DBRI's interrupt
1909 * buffer until it finds a zero word (indicating nothing more to do
1910 * right now). Non-zero words require processing and are handed off
1911 * to dbri_process_one_interrupt AFTER advancing the pointer.
1913 static void dbri_process_interrupt_buffer(struct snd_dbri *dbri)
1917 while ((x = dbri->dma->intr[dbri->dbri_irqp]) != 0) {
1918 dbri->dma->intr[dbri->dbri_irqp] = 0;
1920 if (dbri->dbri_irqp == DBRI_INT_BLK)
1921 dbri->dbri_irqp = 1;
1923 dbri_process_one_interrupt(dbri, x);
1927 static irqreturn_t snd_dbri_interrupt(int irq, void *dev_id)
1929 struct snd_dbri *dbri = dev_id;
1930 static int errcnt = 0;
1935 spin_lock(&dbri->lock);
1938 * Read it, so the interrupt goes away.
1940 x = sbus_readl(dbri->regs + REG1);
1942 if (x & (D_MRR | D_MLE | D_LBG | D_MBE)) {
1947 "DBRI: Multiple Error Ack on SBus reg1=0x%x\n",
1951 "DBRI: Multiple Late Error on SBus reg1=0x%x\n",
1955 "DBRI: Lost Bus Grant on SBus reg1=0x%x\n", x);
1958 "DBRI: Burst Error on SBus reg1=0x%x\n", x);
1960 /* Some of these SBus errors cause the chip's SBus circuitry
1961 * to be disabled, so just re-enable and try to keep going.
1963 * The only one I've seen is MRR, which will be triggered
1964 * if you let a transmit pipe underrun, then try to CDP it.
1966 * If these things persist, we reset the chip.
1968 if ((++errcnt) % 10 == 0) {
1969 dprintk(D_INT, "Interrupt errors exceeded.\n");
1972 tmp = sbus_readl(dbri->regs + REG0);
1974 sbus_writel(tmp, dbri->regs + REG0);
1978 dbri_process_interrupt_buffer(dbri);
1980 spin_unlock(&dbri->lock);
1985 /****************************************************************************
1987 ****************************************************************************/
1988 static struct snd_pcm_hardware snd_dbri_pcm_hw = {
1989 .info = (SNDRV_PCM_INFO_MMAP |
1990 SNDRV_PCM_INFO_INTERLEAVED |
1991 SNDRV_PCM_INFO_BLOCK_TRANSFER |
1992 SNDRV_PCM_INFO_MMAP_VALID),
1993 .formats = SNDRV_PCM_FMTBIT_MU_LAW |
1994 SNDRV_PCM_FMTBIT_A_LAW |
1995 SNDRV_PCM_FMTBIT_U8 |
1996 SNDRV_PCM_FMTBIT_S16_BE,
1997 .rates = SNDRV_PCM_RATE_8000_48000 | SNDRV_PCM_RATE_5512,
2002 .buffer_bytes_max = (64 * 1024),
2003 .period_bytes_min = 1,
2004 .period_bytes_max = DBRI_TD_MAXCNT,
2006 .periods_max = 1024,
2009 static int snd_hw_rule_format(struct snd_pcm_hw_params *params,
2010 struct snd_pcm_hw_rule *rule)
2012 struct snd_interval *c = hw_param_interval(params,
2013 SNDRV_PCM_HW_PARAM_CHANNELS);
2014 struct snd_mask *f = hw_param_mask(params, SNDRV_PCM_HW_PARAM_FORMAT);
2015 struct snd_mask fmt;
2019 fmt.bits[0] &= SNDRV_PCM_FMTBIT_S16_BE;
2020 return snd_mask_refine(f, &fmt);
2025 static int snd_hw_rule_channels(struct snd_pcm_hw_params *params,
2026 struct snd_pcm_hw_rule *rule)
2028 struct snd_interval *c = hw_param_interval(params,
2029 SNDRV_PCM_HW_PARAM_CHANNELS);
2030 struct snd_mask *f = hw_param_mask(params, SNDRV_PCM_HW_PARAM_FORMAT);
2031 struct snd_interval ch;
2033 snd_interval_any(&ch);
2034 if (!(f->bits[0] & SNDRV_PCM_FMTBIT_S16_BE)) {
2038 return snd_interval_refine(c, &ch);
2043 static int snd_dbri_open(struct snd_pcm_substream *substream)
2045 struct snd_dbri *dbri = snd_pcm_substream_chip(substream);
2046 struct snd_pcm_runtime *runtime = substream->runtime;
2047 struct dbri_streaminfo *info = DBRI_STREAM(dbri, substream);
2048 unsigned long flags;
2050 dprintk(D_USR, "open audio output.\n");
2051 runtime->hw = snd_dbri_pcm_hw;
2053 spin_lock_irqsave(&dbri->lock, flags);
2054 info->substream = substream;
2056 info->dvma_buffer = 0;
2058 spin_unlock_irqrestore(&dbri->lock, flags);
2060 snd_pcm_hw_rule_add(runtime, 0, SNDRV_PCM_HW_PARAM_CHANNELS,
2061 snd_hw_rule_format, NULL, SNDRV_PCM_HW_PARAM_FORMAT,
2063 snd_pcm_hw_rule_add(runtime, 0, SNDRV_PCM_HW_PARAM_FORMAT,
2064 snd_hw_rule_channels, NULL,
2065 SNDRV_PCM_HW_PARAM_CHANNELS,
2073 static int snd_dbri_close(struct snd_pcm_substream *substream)
2075 struct snd_dbri *dbri = snd_pcm_substream_chip(substream);
2076 struct dbri_streaminfo *info = DBRI_STREAM(dbri, substream);
2078 dprintk(D_USR, "close audio output.\n");
2079 info->substream = NULL;
2085 static int snd_dbri_hw_params(struct snd_pcm_substream *substream,
2086 struct snd_pcm_hw_params *hw_params)
2088 struct snd_pcm_runtime *runtime = substream->runtime;
2089 struct snd_dbri *dbri = snd_pcm_substream_chip(substream);
2090 struct dbri_streaminfo *info = DBRI_STREAM(dbri, substream);
2094 /* set sampling rate, audio format and number of channels */
2095 ret = cs4215_prepare(dbri, params_rate(hw_params),
2096 params_format(hw_params),
2097 params_channels(hw_params));
2101 if ((ret = snd_pcm_lib_malloc_pages(substream,
2102 params_buffer_bytes(hw_params))) < 0) {
2103 printk(KERN_ERR "malloc_pages failed with %d\n", ret);
2107 /* hw_params can get called multiple times. Only map the DMA once.
2109 if (info->dvma_buffer == 0) {
2110 if (DBRI_STREAMNO(substream) == DBRI_PLAY)
2111 direction = SBUS_DMA_TODEVICE;
2113 direction = SBUS_DMA_FROMDEVICE;
2115 info->dvma_buffer = sbus_map_single(dbri->sdev,
2117 params_buffer_bytes(hw_params),
2121 direction = params_buffer_bytes(hw_params);
2122 dprintk(D_USR, "hw_params: %d bytes, dvma=%x\n",
2123 direction, info->dvma_buffer);
2127 static int snd_dbri_hw_free(struct snd_pcm_substream *substream)
2129 struct snd_dbri *dbri = snd_pcm_substream_chip(substream);
2130 struct dbri_streaminfo *info = DBRI_STREAM(dbri, substream);
2133 dprintk(D_USR, "hw_free.\n");
2135 /* hw_free can get called multiple times. Only unmap the DMA once.
2137 if (info->dvma_buffer) {
2138 if (DBRI_STREAMNO(substream) == DBRI_PLAY)
2139 direction = SBUS_DMA_TODEVICE;
2141 direction = SBUS_DMA_FROMDEVICE;
2143 sbus_unmap_single(dbri->sdev, info->dvma_buffer,
2144 substream->runtime->buffer_size, direction);
2145 info->dvma_buffer = 0;
2147 if (info->pipe != -1) {
2148 reset_pipe(dbri, info->pipe);
2152 return snd_pcm_lib_free_pages(substream);
2155 static int snd_dbri_prepare(struct snd_pcm_substream *substream)
2157 struct snd_dbri *dbri = snd_pcm_substream_chip(substream);
2158 struct dbri_streaminfo *info = DBRI_STREAM(dbri, substream);
2161 info->size = snd_pcm_lib_buffer_bytes(substream);
2162 if (DBRI_STREAMNO(substream) == DBRI_PLAY)
2163 info->pipe = 4; /* Send pipe */
2165 info->pipe = 6; /* Receive pipe */
2167 spin_lock_irq(&dbri->lock);
2170 /* Setup the all the transmit/receive descriptors to cover the
2173 ret = setup_descs(dbri, DBRI_STREAMNO(substream),
2174 snd_pcm_lib_period_bytes(substream));
2176 spin_unlock_irq(&dbri->lock);
2178 dprintk(D_USR, "prepare audio output. %d bytes\n", info->size);
2182 static int snd_dbri_trigger(struct snd_pcm_substream *substream, int cmd)
2184 struct snd_dbri *dbri = snd_pcm_substream_chip(substream);
2185 struct dbri_streaminfo *info = DBRI_STREAM(dbri, substream);
2189 case SNDRV_PCM_TRIGGER_START:
2190 dprintk(D_USR, "start audio, period is %d bytes\n",
2191 (int)snd_pcm_lib_period_bytes(substream));
2192 /* Re-submit the TDs. */
2195 case SNDRV_PCM_TRIGGER_STOP:
2196 dprintk(D_USR, "stop audio.\n");
2197 reset_pipe(dbri, info->pipe);
2206 static snd_pcm_uframes_t snd_dbri_pointer(struct snd_pcm_substream *substream)
2208 struct snd_dbri *dbri = snd_pcm_substream_chip(substream);
2209 struct dbri_streaminfo *info = DBRI_STREAM(dbri, substream);
2210 snd_pcm_uframes_t ret;
2212 ret = bytes_to_frames(substream->runtime, info->offset)
2213 % substream->runtime->buffer_size;
2214 dprintk(D_USR, "I/O pointer: %ld frames of %ld.\n",
2215 ret, substream->runtime->buffer_size);
2219 static struct snd_pcm_ops snd_dbri_ops = {
2220 .open = snd_dbri_open,
2221 .close = snd_dbri_close,
2222 .ioctl = snd_pcm_lib_ioctl,
2223 .hw_params = snd_dbri_hw_params,
2224 .hw_free = snd_dbri_hw_free,
2225 .prepare = snd_dbri_prepare,
2226 .trigger = snd_dbri_trigger,
2227 .pointer = snd_dbri_pointer,
2230 static int __devinit snd_dbri_pcm(struct snd_dbri *dbri)
2232 struct snd_pcm *pcm;
2235 if ((err = snd_pcm_new(dbri->card,
2236 /* ID */ "sun_dbri",
2238 /* playback count */ 1,
2239 /* capture count */ 1, &pcm)) < 0)
2241 snd_assert(pcm != NULL, return -EINVAL);
2243 snd_pcm_set_ops(pcm, SNDRV_PCM_STREAM_PLAYBACK, &snd_dbri_ops);
2244 snd_pcm_set_ops(pcm, SNDRV_PCM_STREAM_CAPTURE, &snd_dbri_ops);
2246 pcm->private_data = dbri;
2247 pcm->info_flags = 0;
2248 strcpy(pcm->name, dbri->card->shortname);
2250 if ((err = snd_pcm_lib_preallocate_pages_for_all(pcm,
2251 SNDRV_DMA_TYPE_CONTINUOUS,
2252 snd_dma_continuous_data(GFP_KERNEL),
2253 64 * 1024, 64 * 1024)) < 0)
2259 /*****************************************************************************
2261 *****************************************************************************/
2263 static int snd_cs4215_info_volume(struct snd_kcontrol *kcontrol,
2264 struct snd_ctl_elem_info *uinfo)
2266 uinfo->type = SNDRV_CTL_ELEM_TYPE_INTEGER;
2268 uinfo->value.integer.min = 0;
2269 if (kcontrol->private_value == DBRI_PLAY) {
2270 uinfo->value.integer.max = DBRI_MAX_VOLUME;
2272 uinfo->value.integer.max = DBRI_MAX_GAIN;
2277 static int snd_cs4215_get_volume(struct snd_kcontrol *kcontrol,
2278 struct snd_ctl_elem_value *ucontrol)
2280 struct snd_dbri *dbri = snd_kcontrol_chip(kcontrol);
2281 struct dbri_streaminfo *info;
2282 snd_assert(dbri != NULL, return -EINVAL);
2283 info = &dbri->stream_info[kcontrol->private_value];
2284 snd_assert(info != NULL, return -EINVAL);
2286 ucontrol->value.integer.value[0] = info->left_gain;
2287 ucontrol->value.integer.value[1] = info->right_gain;
2291 static int snd_cs4215_put_volume(struct snd_kcontrol *kcontrol,
2292 struct snd_ctl_elem_value *ucontrol)
2294 struct snd_dbri *dbri = snd_kcontrol_chip(kcontrol);
2295 struct dbri_streaminfo *info =
2296 &dbri->stream_info[kcontrol->private_value];
2299 if (info->left_gain != ucontrol->value.integer.value[0]) {
2300 info->left_gain = ucontrol->value.integer.value[0];
2303 if (info->right_gain != ucontrol->value.integer.value[1]) {
2304 info->right_gain = ucontrol->value.integer.value[1];
2308 /* First mute outputs, and wait 1/8000 sec (125 us)
2309 * to make sure this takes. This avoids clicking noises.
2311 cs4215_setdata(dbri, 1);
2313 cs4215_setdata(dbri, 0);
2318 static int snd_cs4215_info_single(struct snd_kcontrol *kcontrol,
2319 struct snd_ctl_elem_info *uinfo)
2321 int mask = (kcontrol->private_value >> 16) & 0xff;
2323 uinfo->type = (mask == 1) ?
2324 SNDRV_CTL_ELEM_TYPE_BOOLEAN : SNDRV_CTL_ELEM_TYPE_INTEGER;
2326 uinfo->value.integer.min = 0;
2327 uinfo->value.integer.max = mask;
2331 static int snd_cs4215_get_single(struct snd_kcontrol *kcontrol,
2332 struct snd_ctl_elem_value *ucontrol)
2334 struct snd_dbri *dbri = snd_kcontrol_chip(kcontrol);
2335 int elem = kcontrol->private_value & 0xff;
2336 int shift = (kcontrol->private_value >> 8) & 0xff;
2337 int mask = (kcontrol->private_value >> 16) & 0xff;
2338 int invert = (kcontrol->private_value >> 24) & 1;
2339 snd_assert(dbri != NULL, return -EINVAL);
2342 ucontrol->value.integer.value[0] =
2343 (dbri->mm.data[elem] >> shift) & mask;
2345 ucontrol->value.integer.value[0] =
2346 (dbri->mm.ctrl[elem - 4] >> shift) & mask;
2349 ucontrol->value.integer.value[0] =
2350 mask - ucontrol->value.integer.value[0];
2354 static int snd_cs4215_put_single(struct snd_kcontrol *kcontrol,
2355 struct snd_ctl_elem_value *ucontrol)
2357 struct snd_dbri *dbri = snd_kcontrol_chip(kcontrol);
2358 int elem = kcontrol->private_value & 0xff;
2359 int shift = (kcontrol->private_value >> 8) & 0xff;
2360 int mask = (kcontrol->private_value >> 16) & 0xff;
2361 int invert = (kcontrol->private_value >> 24) & 1;
2364 snd_assert(dbri != NULL, return -EINVAL);
2366 val = (ucontrol->value.integer.value[0] & mask);
2372 dbri->mm.data[elem] = (dbri->mm.data[elem] &
2373 ~(mask << shift)) | val;
2374 changed = (val != dbri->mm.data[elem]);
2376 dbri->mm.ctrl[elem - 4] = (dbri->mm.ctrl[elem - 4] &
2377 ~(mask << shift)) | val;
2378 changed = (val != dbri->mm.ctrl[elem - 4]);
2381 dprintk(D_GEN, "put_single: mask=0x%x, changed=%d, "
2382 "mixer-value=%ld, mm-value=0x%x\n",
2383 mask, changed, ucontrol->value.integer.value[0],
2384 dbri->mm.data[elem & 3]);
2387 /* First mute outputs, and wait 1/8000 sec (125 us)
2388 * to make sure this takes. This avoids clicking noises.
2390 cs4215_setdata(dbri, 1);
2392 cs4215_setdata(dbri, 0);
2397 /* Entries 0-3 map to the 4 data timeslots, entries 4-7 map to the 4 control
2398 timeslots. Shift is the bit offset in the timeslot, mask defines the
2399 number of bits. invert is a boolean for use with attenuation.
2401 #define CS4215_SINGLE(xname, entry, shift, mask, invert) \
2402 { .iface = SNDRV_CTL_ELEM_IFACE_MIXER, .name = (xname), \
2403 .info = snd_cs4215_info_single, \
2404 .get = snd_cs4215_get_single, .put = snd_cs4215_put_single, \
2405 .private_value = (entry) | ((shift) << 8) | ((mask) << 16) | \
2408 static struct snd_kcontrol_new dbri_controls[] __devinitdata = {
2410 .iface = SNDRV_CTL_ELEM_IFACE_MIXER,
2411 .name = "Playback Volume",
2412 .info = snd_cs4215_info_volume,
2413 .get = snd_cs4215_get_volume,
2414 .put = snd_cs4215_put_volume,
2415 .private_value = DBRI_PLAY,
2417 CS4215_SINGLE("Headphone switch", 0, 7, 1, 0)
2418 CS4215_SINGLE("Line out switch", 0, 6, 1, 0)
2419 CS4215_SINGLE("Speaker switch", 1, 6, 1, 0)
2421 .iface = SNDRV_CTL_ELEM_IFACE_MIXER,
2422 .name = "Capture Volume",
2423 .info = snd_cs4215_info_volume,
2424 .get = snd_cs4215_get_volume,
2425 .put = snd_cs4215_put_volume,
2426 .private_value = DBRI_REC,
2428 /* FIXME: mic/line switch */
2429 CS4215_SINGLE("Line in switch", 2, 4, 1, 0)
2430 CS4215_SINGLE("High Pass Filter switch", 5, 7, 1, 0)
2431 CS4215_SINGLE("Monitor Volume", 3, 4, 0xf, 1)
2432 CS4215_SINGLE("Mic boost", 4, 4, 1, 1)
2435 static int __init snd_dbri_mixer(struct snd_dbri *dbri)
2437 struct snd_card *card;
2440 snd_assert(dbri != NULL && dbri->card != NULL, return -EINVAL);
2443 strcpy(card->mixername, card->shortname);
2445 for (idx = 0; idx < ARRAY_SIZE(dbri_controls); idx++) {
2446 if ((err = snd_ctl_add(card,
2447 snd_ctl_new1(&dbri_controls[idx], dbri))) < 0)
2451 for (idx = DBRI_REC; idx < DBRI_NO_STREAMS; idx++) {
2452 dbri->stream_info[idx].left_gain = 0;
2453 dbri->stream_info[idx].right_gain = 0;
2459 /****************************************************************************
2461 ****************************************************************************/
2462 static void dbri_regs_read(struct snd_info_entry *entry,
2463 struct snd_info_buffer *buffer)
2465 struct snd_dbri *dbri = entry->private_data;
2467 snd_iprintf(buffer, "REG0: 0x%x\n", sbus_readl(dbri->regs + REG0));
2468 snd_iprintf(buffer, "REG2: 0x%x\n", sbus_readl(dbri->regs + REG2));
2469 snd_iprintf(buffer, "REG8: 0x%x\n", sbus_readl(dbri->regs + REG8));
2470 snd_iprintf(buffer, "REG9: 0x%x\n", sbus_readl(dbri->regs + REG9));
2474 static void dbri_debug_read(struct snd_info_entry *entry,
2475 struct snd_info_buffer *buffer)
2477 struct snd_dbri *dbri = entry->private_data;
2479 snd_iprintf(buffer, "debug=%d\n", dbri_debug);
2481 for (pipe = 0; pipe < 32; pipe++) {
2482 if (pipe_active(dbri, pipe)) {
2483 struct dbri_pipe *pptr = &dbri->pipes[pipe];
2485 "Pipe %d: %s SDP=0x%x desc=%d, "
2488 ((pptr->sdp & D_SDP_TO_SER) ? "output" :
2490 pptr->sdp, pptr->desc,
2491 pptr->length, pptr->nextpipe);
2497 void snd_dbri_proc(struct snd_dbri *dbri)
2499 struct snd_info_entry *entry;
2501 if (!snd_card_proc_new(dbri->card, "regs", &entry))
2502 snd_info_set_text_ops(entry, dbri, dbri_regs_read);
2505 if (! snd_card_proc_new(dbri->card, "debug", &entry)) {
2506 snd_info_set_text_ops(entry, dbri, dbri_debug_read);
2507 entry->mode = S_IFREG | S_IRUGO; /* Readable only. */
2513 ****************************************************************************
2514 **************************** Initialization ********************************
2515 ****************************************************************************
2517 static void snd_dbri_free(struct snd_dbri *dbri);
2519 static int __init snd_dbri_create(struct snd_card *card,
2520 struct sbus_dev *sdev,
2521 struct linux_prom_irqs *irq, int dev)
2523 struct snd_dbri *dbri = card->private_data;
2526 spin_lock_init(&dbri->lock);
2529 dbri->irq = irq->pri;
2531 dbri->dma = sbus_alloc_consistent(sdev, sizeof(struct dbri_dma),
2533 memset((void *)dbri->dma, 0, sizeof(struct dbri_dma));
2535 dprintk(D_GEN, "DMA Cmd Block 0x%p (0x%08x)\n",
2536 dbri->dma, dbri->dma_dvma);
2538 /* Map the registers into memory. */
2539 dbri->regs_size = sdev->reg_addrs[0].reg_size;
2540 dbri->regs = sbus_ioremap(&sdev->resource[0], 0,
2541 dbri->regs_size, "DBRI Registers");
2543 printk(KERN_ERR "DBRI: could not allocate registers\n");
2544 sbus_free_consistent(sdev, sizeof(struct dbri_dma),
2545 (void *)dbri->dma, dbri->dma_dvma);
2549 err = request_irq(dbri->irq, snd_dbri_interrupt, IRQF_SHARED,
2550 "DBRI audio", dbri);
2552 printk(KERN_ERR "DBRI: Can't get irq %d\n", dbri->irq);
2553 sbus_iounmap(dbri->regs, dbri->regs_size);
2554 sbus_free_consistent(sdev, sizeof(struct dbri_dma),
2555 (void *)dbri->dma, dbri->dma_dvma);
2559 /* Do low level initialization of the DBRI and CS4215 chips */
2560 dbri_initialize(dbri);
2561 err = cs4215_init(dbri);
2563 snd_dbri_free(dbri);
2567 dbri->next = dbri_list;
2573 static void snd_dbri_free(struct snd_dbri *dbri)
2575 dprintk(D_GEN, "snd_dbri_free\n");
2579 free_irq(dbri->irq, dbri);
2582 sbus_iounmap(dbri->regs, dbri->regs_size);
2585 sbus_free_consistent(dbri->sdev, sizeof(struct dbri_dma),
2586 (void *)dbri->dma, dbri->dma_dvma);
2589 static int __init dbri_attach(int prom_node, struct sbus_dev *sdev)
2591 struct snd_dbri *dbri;
2592 struct linux_prom_irqs irq;
2593 struct resource *rp;
2594 struct snd_card *card;
2598 if (sdev->prom_name[9] < 'e') {
2599 printk(KERN_ERR "DBRI: unsupported chip version %c found.\n",
2600 sdev->prom_name[9]);
2604 if (dev >= SNDRV_CARDS)
2611 err = prom_getproperty(prom_node, "intr", (char *)&irq, sizeof(irq));
2613 printk(KERN_ERR "DBRI-%d: Firmware node lacks IRQ property.\n",
2618 card = snd_card_new(index[dev], id[dev], THIS_MODULE,
2619 sizeof(struct snd_dbri));
2623 strcpy(card->driver, "DBRI");
2624 strcpy(card->shortname, "Sun DBRI");
2625 rp = &sdev->resource[0];
2626 sprintf(card->longname, "%s at 0x%02lx:0x%016Lx, irq %d",
2628 rp->flags & 0xffL, (unsigned long long)rp->start, irq.pri);
2630 if ((err = snd_dbri_create(card, sdev, &irq, dev)) < 0) {
2631 snd_card_free(card);
2635 dbri = card->private_data;
2636 if ((err = snd_dbri_pcm(dbri)) < 0)
2639 if ((err = snd_dbri_mixer(dbri)) < 0)
2640 if ((err = snd_dbri_mixer(dbri)) < 0)
2643 /* /proc file handling */
2644 snd_dbri_proc(dbri);
2646 err = snd_card_register(card);
2650 printk(KERN_INFO "audio%d at %p (irq %d) is DBRI(%c)+CS4215(%d)\n",
2652 dbri->irq, sdev->prom_name[9], dbri->mm.version);
2658 snd_dbri_free(dbri);
2659 snd_card_free(card);
2663 /* Probe for the dbri chip and then attach the driver. */
2664 static int __init dbri_init(void)
2666 struct sbus_bus *sbus;
2667 struct sbus_dev *sdev;
2670 /* Probe each SBUS for the DBRI chip(s). */
2671 for_all_sbusdev(sdev, sbus) {
2673 * The version is coded in the last character
2675 if (!strncmp(sdev->prom_name, "SUNW,DBRI", 9)) {
2676 dprintk(D_GEN, "DBRI: Found %s in SBUS slot %d\n",
2677 sdev->prom_name, sdev->slot);
2679 if (dbri_attach(sdev->prom_node, sdev) == 0)
2684 return (found > 0) ? 0 : -EIO;
2687 static void __exit dbri_exit(void)
2689 struct snd_dbri *this = dbri_list;
2691 while (this != NULL) {
2692 struct snd_dbri *next = this->next;
2693 struct snd_card *card = this->card;
2695 snd_dbri_free(this);
2696 snd_card_free(card);
2702 module_init(dbri_init);
2703 module_exit(dbri_exit);