Pull ar-k0-usage into release branch

[linux-2.6] / sound / oss / Kconfig

# drivers/sound/Config.in
#
# 18 Apr 1998, Michael Elizabeth Chastain, <mailto:mec@shout.net>
# More hacking for modularisation.
#
# Prompt user for primary drivers.
config SOUND_BT878
        tristate "BT878 audio dma"
        depends on SOUND_PRIME && PCI
        ---help---
          Audio DMA support for bt878 based grabber boards.  As you might have
          already noticed, bt878 is listed with two functions in /proc/pci.
          Function 0 does the video stuff (bt848 compatible), function 1 does
          the same for audio data.  This is a driver for the audio part of
          the chip.  If you say 'Y' here you get a oss-compatible dsp device
          where you can record from.  If you want just watch TV you probably
          don't need this driver as most TV cards handle sound with a short
          cable from the TV card to your sound card's line-in.

          To compile this driver as a module, choose M here: the module will
          be called btaudio.

config SOUND_CMPCI
        tristate "C-Media PCI (CMI8338/8738)"
        depends on SOUND_PRIME && PCI
        help
          Say Y or M if you have a PCI sound card using the CMI8338
          or the CMI8738 chipset.  Data on these chips are available at
          <http://www.cmedia.com.tw/>.

          A userspace utility to control some internal registers of these
          chips is available at
          <http://member.nifty.ne.jp/Breeze/softwares/unix/cmictl-e.html>.

config SOUND_CMPCI_FM
        bool "Enable legacy FM"
        depends on SOUND_CMPCI && X86
        help
          Say Y here to enable the legacy FM (frequency-modulation) synthesizer
          support on a card using the CMI8338 or CMI8378 chipset. Even it is
          enabled, you need to set fmio as proper value to enable it.
          Say N here if you don't need this.

config SOUND_CMPCI_MIDI
        bool "Enable legacy MPU-401"
        depends on SOUND_CMPCI && X86
        help
          Say Y here to enable the legacy MPU401 MIDI synthesizer support on a
          card using the CMI8338 or CMI8378 chipset. Even it is enabled,
          you need to set mpuio as proper value to enable it.
          Say N here if you don't need this.

config SOUND_CMPCI_JOYSTICK
        bool "Enable joystick"
        depends on SOUND_CMPCI && X86 && (GAMEPORT=y || SOUND_CMPCI=GAMEPORT)
        help
          Say Y here in order to enable the joystick port on a sound card using
          the CMI8338 or the CMI8738 chipset.  You need to config the
          gameport support and set joystick parameter as 1 to use it.
          Say N here if you don't need this.

config SOUND_EMU10K1
        tristate "Creative SBLive! (EMU10K1)"
        depends on SOUND_PRIME && PCI
        ---help---
          Say Y or M if you have a PCI sound card using the EMU10K1 chipset,
          such as the Creative SBLive!, SB PCI512 or Emu-APS.

          For more information on this driver and the degree of support for
          the different card models please check:

                <http://sourceforge.net/projects/emu10k1/>

          It is now possible to load dsp microcode patches into the EMU10K1
          chip.  These patches are used to implement real time sound
          processing effects which include for example: signal routing,
          bass/treble control, AC3 passthrough, ...
          Userspace tools to create new patches and load/unload them can be
          found in the emu-tools package at the above URL.

config MIDI_EMU10K1
        bool "Creative SBLive! MIDI (EXPERIMENTAL)"
        depends on SOUND_EMU10K1 && EXPERIMENTAL && ISA_DMA_API
        help
          Say Y if you want to be able to use the OSS /dev/sequencer
          interface.  This code is still experimental.

config SOUND_FUSION
        tristate "Crystal SoundFusion (CS4280/461x)"
        depends on SOUND_PRIME && PCI
        help
          This module drives the Crystal SoundFusion devices (CS4280/46xx
          series) when wired as native sound drivers with AC97 codecs.  If
          this driver does not work try the CS4232 driver.

config SOUND_CS4281
        tristate "Crystal Sound CS4281"
        depends on SOUND_PRIME && PCI
        help
          Picture and feature list at
          <http://www.pcbroker.com/crystal4281.html>.

config SOUND_BCM_CS4297A
        tristate "Crystal Sound CS4297a (for Swarm)"
        depends on SOUND_PRIME && SIBYTE_SWARM
        help
          The BCM91250A has a Crystal CS4297a on synchronous serial
          port B (in addition to the DB-9 serial port).  Say Y or M
          here to enable the sound chip instead of the UART.  Also
          note that CONFIG_KGDB should not be enabled at the same
          time, since it also attempts to use this UART port.

config SOUND_ES1370
        tristate "Ensoniq AudioPCI (ES1370)"
        depends on SOUND_PRIME && PCI
        help
          Say Y or M if you have a PCI sound card utilizing the Ensoniq
          ES1370 chipset, such as Ensoniq's AudioPCI (non-97). To find
          out if your sound card uses an ES1370 without removing your
          computer's cover, use lspci -n and look for the PCI ID
          1274:5000. Since Ensoniq was bought by Creative Labs,
          Sound Blaster 64/PCI models are either ES1370 or ES1371 based.
          This driver differs slightly from OSS/Free, so PLEASE READ
          <file:Documentation/sound/oss/es1370>.

config SOUND_ES1371
        tristate "Creative Ensoniq AudioPCI 97 (ES1371)"
        depends on SOUND_PRIME && PCI
        help
          Say Y or M if you have a PCI sound card utilizing the Ensoniq
          ES1371 chipset, such as Ensoniq's AudioPCI97. To find out if
          your sound card uses an ES1371 without removing your computer's
          cover, use lspci -n and look for the PCI ID 1274:1371. Since
          Ensoniq was bought by Creative Labs, Sound Blaster 64/PCI
          models are either ES1370 or ES1371 based. This driver differs
          slightly from OSS/Free, so PLEASE READ
          <file:Documentation/sound/oss/es1371>.

config SOUND_ESSSOLO1
        tristate "ESS Technology Solo1" 
        depends on SOUND_PRIME && PCI
        help
          Say Y or M if you have a PCI sound card utilizing the ESS Technology
          Solo1 chip. To find out if your sound card uses a
          Solo1 chip without removing your computer's cover, use
          lspci -n and look for the PCI ID 125D:1969. This driver
          differs slightly from OSS/Free, so PLEASE READ
          <file:Documentation/sound/oss/solo1>.

config SOUND_MAESTRO
        tristate "ESS Maestro, Maestro2, Maestro2E driver"
        depends on SOUND_PRIME && PCI
        help
          Say Y or M if you have a sound system driven by ESS's Maestro line
          of PCI sound chips.  These include the Maestro 1, Maestro 2, and
          Maestro 2E.  See <file:Documentation/sound/oss/Maestro> for more
          details.

config SOUND_MAESTRO3
        tristate "ESS Maestro3/Allegro driver (EXPERIMENTAL)"
        depends on SOUND_PRIME && PCI && EXPERIMENTAL
        help
          Say Y or M if you have a sound system driven by ESS's Maestro 3
          PCI sound chip.

config SOUND_ICH
        tristate "Intel ICH (i8xx) audio support"
        depends on SOUND_PRIME && PCI
        help
          Support for integral audio in Intel's I/O Controller Hub (ICH)
          chipset, as used on the 810/820/840 motherboards.

config SOUND_HARMONY
        tristate "PA Harmony audio driver"
        depends on GSC_LASI && SOUND_PRIME
        help
          Say 'Y' or 'M' to include support for Harmony soundchip
          on HP 712, 715/new and many other GSC based machines.

config SOUND_SONICVIBES
        tristate "S3 SonicVibes"
        depends on SOUND_PRIME && PCI
        help
          Say Y or M if you have a PCI sound card utilizing the S3
          SonicVibes chipset. To find out if your sound card uses a
          SonicVibes chip without removing your computer's cover, use
          lspci -n and look for the PCI ID 5333:CA00. This driver
          differs slightly from OSS/Free, so PLEASE READ
          <file:Documentation/sound/oss/sonicvibes>.

config SOUND_VWSND
        tristate "SGI Visual Workstation Sound"
        depends on SOUND_PRIME && X86_VISWS
        help
          Say Y or M if you have an SGI Visual Workstation and you want to be
          able to use its on-board audio.  Read
          <file:Documentation/sound/oss/vwsnd> for more info on this driver's
          capabilities.

config SOUND_HAL2
        tristate "SGI HAL2 sound (EXPERIMENTAL)"
        depends on SOUND_PRIME && SGI_IP22 && EXPERIMENTAL
        help
          Say Y or M if you have an SGI Indy system and want to be able to
          use it's on-board A2 audio system.

config SOUND_IT8172
        tristate "IT8172G Sound"
        depends on SOUND_PRIME && (MIPS_ITE8172 || MIPS_IVR)

config SOUND_VRC5477
        tristate "NEC Vrc5477 AC97 sound"
        depends on SOUND_PRIME && DDB5477
        help
          Say Y here to enable sound support for the NEC Vrc5477 chip, an
          integrated, multi-function controller chip for MIPS CPUs.  Works
          with the AC97 codec.

config SOUND_AU1000
        tristate "Au1000 Sound"
        depends on SOUND_PRIME && (SOC_AU1000 || SOC_AU1100 || SOC_AU1500)

config SOUND_AU1550_AC97
        tristate "Au1550 AC97 Sound"
        depends on SOUND_PRIME && SOC_AU1550

config SOUND_TRIDENT
        tristate "Trident 4DWave DX/NX, SiS 7018 or ALi 5451 PCI Audio Core"
        depends on SOUND_PRIME && PCI
        ---help---
          Say Y or M if you have a PCI sound card utilizing the Trident
          4DWave-DX/NX chipset or your mother board chipset has SiS 7018
          or ALi 5451 built-in. The SiS 7018 PCI Audio Core is embedded
          in SiS960 Super South Bridge and SiS540/630 Single Chipset.
          The ALi 5451 PCI Audio Core is embedded in ALi M1535, M1535D,
          M1535+ or M1535D+ South Bridge.

          Use lspci -n to find out if your sound card or chipset uses
          Trident 4DWave or SiS 7018. PCI ID 1023:2000 or 1023:2001 stands
          for Trident 4Dwave. PCI ID 1039:7018 stands for SiS7018. PCI ID
          10B9:5451 stands for ALi5451.

          This driver supports S/PDIF in/out (record/playback) for ALi 5451
          embedded in ALi M1535+ and M1535D+. Note that they aren't all
          enabled by default; you can enable them by saying Y to "/proc file
          system support" and "Sysctl support", and after the /proc file
          system has been mounted, executing the command

                command                 what is enabled

          echo 0>/proc/ALi5451  pcm out is also set to S/PDIF out. (Default).

          echo 1>/proc/ALi5451  use S/PDIF out to output pcm data.

          echo 2>/proc/ALi5451  use S/PDIF out to output non-pcm data.
          (AC3...).

          echo 3>/proc/ALi5451  record from Ac97 in(MIC, Line in...).
          (Default).

          echo 4>/proc/ALi5451  no matter Ac97 settings, record from S/PDIF
          in.


          This driver differs slightly from OSS/Free, so PLEASE READ the
          comments at the top of <file:drivers/sound/trident.c>.

config SOUND_MSNDCLAS
        tristate "Support for Turtle Beach MultiSound Classic, Tahiti, Monterey"
        depends on SOUND_PRIME && (m || !STANDALONE)
        help
          Say M here if you have a Turtle Beach MultiSound Classic, Tahiti or
          Monterey (not for the Pinnacle or Fiji).

          See <file:Documentation/sound/oss/MultiSound> for important information
          about this driver.  Note that it has been discontinued, but the
          Voyetra Turtle Beach knowledge base entry for it is still available
          at <http://www.turtlebeach.com/site/kb_ftp/790.asp>.

comment "Compiled-in MSND Classic support requires firmware during compilation."
        depends on SOUND_PRIME && SOUND_MSNDCLAS=y

config MSNDCLAS_HAVE_BOOT
        bool
        depends on SOUND_MSNDCLAS=y && !STANDALONE
        default y

config MSNDCLAS_INIT_FILE
        string "Full pathname of MSNDINIT.BIN firmware file"
        depends on SOUND_MSNDCLAS
        default "/etc/sound/msndinit.bin"
        help
          The MultiSound cards have two firmware files which are required for
          operation, and are not currently included. These files can be
          obtained from Turtle Beach. See
          <file:Documentation/sound/oss/MultiSound> for information on how to
          obtain this.

config MSNDCLAS_PERM_FILE
        string "Full pathname of MSNDPERM.BIN firmware file"
        depends on SOUND_MSNDCLAS
        default "/etc/sound/msndperm.bin"
        help
          The MultiSound cards have two firmware files which are required for
          operation, and are not currently included. These files can be
          obtained from Turtle Beach. See
          <file:Documentation/sound/oss/MultiSound> for information on how to
          obtain this.

config MSNDCLAS_IRQ
        int "MSND Classic IRQ 5, 7, 9, 10, 11, 12"
        depends on SOUND_MSNDCLAS=y
        default "5"
        help
          Interrupt Request line for the MultiSound Classic and related cards.

config MSNDCLAS_MEM
        hex "MSND Classic memory B0000, C8000, D0000, D8000, E0000, E8000"
        depends on SOUND_MSNDCLAS=y
        default "D0000"
        help
          Memory-mapped I/O base address for the MultiSound Classic and
          related cards.

config MSNDCLAS_IO
        hex "MSND Classic I/O 210, 220, 230, 240, 250, 260, 290, 3E0"
        depends on SOUND_MSNDCLAS=y
        default "290"
        help
          I/O port address for the MultiSound Classic and related cards.

config SOUND_MSNDPIN
        tristate "Support for Turtle Beach MultiSound Pinnacle, Fiji"
        depends on SOUND_PRIME && (m || !STANDALONE)
        help
          Say M here if you have a Turtle Beach MultiSound Pinnacle or Fiji.
          See <file:Documentation/sound/oss/MultiSound> for important information
          about this driver. Note that it has been discontinued, but the
          Voyetra Turtle Beach knowledge base entry for it is still available
          at <http://www.turtlebeach.com/site/kb_ftp/600.asp>.

comment "Compiled-in MSND Pinnacle support requires firmware during compilation."
        depends on SOUND_PRIME && SOUND_MSNDPIN=y

config MSNDPIN_HAVE_BOOT
        bool
        depends on SOUND_MSNDPIN=y
        default y

config MSNDPIN_INIT_FILE
        string "Full pathname of PNDSPINI.BIN firmware file"
        depends on SOUND_MSNDPIN
        default "/etc/sound/pndspini.bin"
        help
          The MultiSound cards have two firmware files which are required
          for operation, and are not currently included. These files can be
          obtained from Turtle Beach. See
          <file:Documentation/sound/oss/MultiSound> for information on how to
          obtain this.

config MSNDPIN_PERM_FILE
        string "Full pathname of PNDSPERM.BIN firmware file"
        depends on SOUND_MSNDPIN
        default "/etc/sound/pndsperm.bin"
        help
          The MultiSound cards have two firmware files which are required for
          operation, and are not currently included. These files can be
          obtained from Turtle Beach. See
          <file:Documentation/sound/oss/MultiSound> for information on how to
          obtain this.

config MSNDPIN_IRQ
        int "MSND Pinnacle IRQ 5, 7, 9, 10, 11, 12"
        depends on SOUND_MSNDPIN=y
        default "5"
        help
          Interrupt request line for the primary synthesizer on MultiSound
          Pinnacle and Fiji sound cards.

config MSNDPIN_MEM
        hex "MSND Pinnacle memory B0000, C8000, D0000, D8000, E0000, E8000"
        depends on SOUND_MSNDPIN=y
        default "D0000"
        help
          Memory-mapped I/O base address for the primary synthesizer on
          MultiSound Pinnacle and Fiji sound cards.

config MSNDPIN_IO
        hex "MSND Pinnacle I/O 210, 220, 230, 240, 250, 260, 290, 3E0"
        depends on SOUND_MSNDPIN=y
        default "290"
        help
          Memory-mapped I/O base address for the primary synthesizer on
          MultiSound Pinnacle and Fiji sound cards.

config MSNDPIN_DIGITAL
        bool "MSND Pinnacle has S/PDIF I/O"
        depends on SOUND_MSNDPIN=y
        help
          If you have the S/PDIF daughter board for the Pinnacle or Fiji,
          answer Y here; otherwise, say N. If you have this, you will be able
          to play and record from the S/PDIF port (digital signal). See
          <file:Documentation/sound/oss/MultiSound> for information on how to make
          use of this capability.

config MSNDPIN_NONPNP
        bool "MSND Pinnacle non-PnP Mode"
        depends on SOUND_MSNDPIN=y
        help
          The Pinnacle and Fiji card resources can be configured either with
          PnP, or through a configuration port. Say Y here if your card is NOT
          in PnP mode. For the Pinnacle, configuration in non-PnP mode allows
          use of the IDE and joystick peripherals on the card as well; these
          do not show up when the card is in PnP mode. Specifying zero for any
          resource of a device will disable the device. If you are running the
          card in PnP mode, you must say N here and use isapnptools to
          configure the card's resources.

comment "MSND Pinnacle DSP section will be configured to above parameters."
        depends on SOUND_PRIME && SOUND_MSNDPIN=y && MSNDPIN_NONPNP

config MSNDPIN_CFG
        hex "MSND Pinnacle config port 250,260,270"
        depends on MSNDPIN_NONPNP
        default "250"
        help
          This is the port which the Pinnacle and Fiji uses to configure the
          card's resources when not in PnP mode. If your card is in PnP mode,
          then be sure to say N to the previous option, "MSND Pinnacle Non-PnP
          Mode".

comment "Pinnacle-specific Device Configuration (0 disables)"
        depends on SOUND_PRIME && SOUND_MSNDPIN=y && MSNDPIN_NONPNP

config MSNDPIN_MPU_IO
        hex "MSND Pinnacle MPU I/O (e.g. 330)"
        depends on MSNDPIN_NONPNP
        default "0"
        help
          Memory-mapped I/O base address for the Kurzweil daughterboard
          synthesizer on MultiSound Pinnacle and Fiji sound cards.

config MSNDPIN_MPU_IRQ
        int "MSND Pinnacle MPU IRQ (e.g. 9)"
        depends on MSNDPIN_NONPNP
        default "0"
        help
          Interrupt request number for the Kurzweil daughterboard
          synthesizer on MultiSound Pinnacle and Fiji sound cards.

config MSNDPIN_IDE_IO0
        hex "MSND Pinnacle IDE I/O 0 (e.g. 170)"
        depends on MSNDPIN_NONPNP
        default "0"
        help
          CD-ROM drive 0 memory-mapped I/O base address for the MultiSound
          Pinnacle and Fiji sound cards.

config MSNDPIN_IDE_IO1
        hex "MSND Pinnacle IDE I/O 1 (e.g. 376)"
        depends on MSNDPIN_NONPNP
        default "0"
        help
          CD-ROM drive 1 memory-mapped I/O base address for the MultiSound
          Pinnacle and Fiji sound cards.

config MSNDPIN_IDE_IRQ
        int "MSND Pinnacle IDE IRQ (e.g. 15)"
        depends on MSNDPIN_NONPNP
        default "0"
        help
          Interrupt request number for the IDE CD-ROM interface on the
          MultiSound Pinnacle and Fiji sound cards.

config MSNDPIN_JOYSTICK_IO
        hex "MSND Pinnacle joystick I/O (e.g. 200)"
        depends on MSNDPIN_NONPNP
        default "0"
        help
          Memory-mapped I/O base address for the joystick port on MultiSound
          Pinnacle and Fiji sound cards.

config MSND_FIFOSIZE
        int "MSND buffer size (kB)"
        depends on SOUND_PRIME && (SOUND_MSNDPIN=y || SOUND_MSNDCLAS=y)
        default "128"
        help
          Configures the size of each audio buffer, in kilobytes, for
          recording and playing in the MultiSound drivers (both the Classic
          and Pinnacle). Larger values reduce the chance of data overruns at
          the expense of overall latency. If unsure, use the default.

config SOUND_VIA82CXXX
        tristate "VIA 82C686 Audio Codec"
        depends on SOUND_PRIME && PCI
        help
          Say Y here to include support for the audio codec found on VIA
          82Cxxx-based chips. Typically these are built into a motherboard.

          DO NOT select Sound Blaster or Adlib with this driver, unless
          you have a Sound Blaster or Adlib card in addition to your VIA
          audio chip.

config MIDI_VIA82CXXX
        bool "VIA 82C686 MIDI"
        depends on SOUND_VIA82CXXX && ISA_DMA_API
        help
          Answer Y to use the MIDI interface of the Via686. You may need to
          enable this in the BIOS before it will work. This is for connection
          to external MIDI hardware, and is not required for software playback
          of MIDI files.

config SOUND_OSS
        tristate "OSS sound modules"
        depends on SOUND_PRIME && ISA_DMA_API
        help
          OSS is the Open Sound System suite of sound card drivers.  They make
          sound programming easier since they provide a common API.  Say Y or
          M here (the module will be called sound) if you haven't found a
          driver for your sound card above, then pick your driver from the
          list below.

config SOUND_TRACEINIT
        bool "Verbose initialisation"
        depends on SOUND_OSS
        help
          Verbose soundcard initialization -- affects the format of autoprobe
          and initialization messages at boot time.

config SOUND_DMAP
        bool "Persistent DMA buffers"
        depends on SOUND_OSS
        ---help---
          Linux can often have problems allocating DMA buffers for ISA sound
          cards on machines with more than 16MB of RAM. This is because ISA
          DMA buffers must exist below the 16MB boundary and it is quite
          possible that a large enough free block in this region cannot be
          found after the machine has been running for a while. If you say Y
          here the DMA buffers (64Kb) will be allocated at boot time and kept
          until the shutdown. This option is only useful if you said Y to
          "OSS sound modules", above. If you said M to "OSS sound modules"
          then you can get the persistent DMA buffer functionality by passing
          the command-line argument "dmabuf=1" to the sound module.

          Say Y unless you have 16MB or more RAM or a PCI sound card.

config SOUND_AD1816
        tristate "AD1816(A) based cards (EXPERIMENTAL)"
        depends on EXPERIMENTAL && SOUND_OSS
        help
          Say M here if you have a sound card based on the Analog Devices
          AD1816(A) chip.

          If you compile the driver into the kernel, you have to add
          "ad1816=<io>,<irq>,<dma>,<dma2>" to the kernel command line.

config SOUND_AD1889
        tristate "AD1889 based cards (AD1819 codec) (EXPERIMENTAL)"
        depends on EXPERIMENTAL && SOUND_OSS && PCI
        help
          Say M here if you have a sound card based on the Analog Devices
          AD1889 chip.

config SOUND_SGALAXY
        tristate "Aztech Sound Galaxy (non-PnP) cards"
        depends on SOUND_OSS
        help
          This module initializes the older non Plug and Play sound galaxy
          cards from Aztech. It supports the Waverider Pro 32 - 3D and the
          Galaxy Washington 16.

          If you compile the driver into the kernel, you have to add
          "sgalaxy=<io>,<irq>,<dma>,<dma2>,<sgbase>" to the kernel command
          line.

config SOUND_ADLIB
        tristate "Adlib Cards"
        depends on SOUND_OSS
        help
          Includes ASB 64 4D. Information on programming AdLib cards is
          available at <http://www.itsnet.com/home/ldragon/Specs/adlib.html>.

config SOUND_ACI_MIXER
        tristate "ACI mixer (miroSOUND PCM1-pro/PCM12/PCM20)"
        depends on SOUND_OSS
        ---help---
          ACI (Audio Command Interface) is a protocol used to communicate with
          the microcontroller on some sound cards produced by miro and
          Cardinal Technologies.  The main function of the ACI is to control
          the mixer and to get a product identification.

          This VoxWare ACI driver currently supports the ACI functions on the
          miroSOUND PCM1-pro, PCM12 and PCM20 radio. On the PCM20 radio, ACI
          also controls the radio tuner. This is supported in the video4linux
          miropcm20 driver (say M or Y here and go back to "Multimedia
          devices" -> "Radio Adapters").

          This driver is also available as a module and will be called aci.

config SOUND_CS4232
        tristate "Crystal CS4232 based (PnP) cards"
        depends on SOUND_OSS
        help
          Say Y here if you have a card based on the Crystal CS4232 chip set,
          which uses its own Plug and Play protocol.

          If you compile the driver into the kernel, you have to add
          "cs4232=<io>,<irq>,<dma>,<dma2>,<mpuio>,<mpuirq>" to the kernel
          command line.

          See <file:Documentation/sound/oss/CS4232> for more information on
          configuring this card.

config SOUND_SSCAPE
        tristate "Ensoniq SoundScape support"
        depends on SOUND_OSS
        help
          Answer Y if you have a sound card based on the Ensoniq SoundScape
          chipset. Such cards are being manufactured at least by Ensoniq, Spea
          and Reveal (Reveal makes also other cards).

          If you compile the driver into the kernel, you have to add
          "sscape=<io>,<irq>,<dma>,<mpuio>,<mpuirq>" to the kernel command
          line.

config SOUND_GUS
        tristate "Gravis Ultrasound support"
        depends on SOUND_OSS
        help
          Say Y here for any type of Gravis Ultrasound card, including the GUS
          or GUS MAX.  See also <file:Documentation/sound/oss/ultrasound> for more
          information on configuring this card with modules.

          If you compile the driver into the kernel, you have to add
          "gus=<io>,<irq>,<dma>,<dma2>" to the kernel command line.

config SOUND_GUS16
        bool "16 bit sampling option of GUS (_NOT_ GUS MAX)"
        depends on SOUND_GUS
        help
          Support for Gravis Ulstrasound (GUS) cards (other than the GUS),
          sampling at 16-bit width.

config SOUND_GUSMAX
        bool "GUS MAX support"
        depends on SOUND_GUS
        help
          Support for Gravis Ulstrasound MAX.

config SOUND_VMIDI
        tristate "Loopback MIDI device support"
        depends on SOUND_OSS
        help
          Support for MIDI loopback on port 1 or 2.

config SOUND_TRIX
        tristate "MediaTrix AudioTrix Pro support"
        depends on SOUND_OSS
        help
          Answer Y if you have the AudioTriX Pro sound card manufactured
          by MediaTrix.

config TRIX_HAVE_BOOT
        bool "Have TRXPRO.HEX firmware file"
        depends on SOUND_TRIX=y && !STANDALONE
        help
          The MediaTrix AudioTrix Pro has an on-board microcontroller which
          needs to be initialized by downloading the code from the file
          TRXPRO.HEX in the DOS driver directory. If you don't have the
          TRXPRO.HEX file handy you may skip this step. However, the SB and
          MPU-401 modes of AudioTrix Pro will not work without this file!

config TRIX_BOOT_FILE
        string "Full pathname of TRXPRO.HEX firmware file"
        depends on TRIX_HAVE_BOOT
        default "/etc/sound/trxpro.hex"
        help
          Enter the full pathname of your TRXPRO.HEX file, starting from /.

config SOUND_MSS
        tristate "Microsoft Sound System support"
        depends on SOUND_OSS
        ---help---
          Again think carefully before answering Y to this question.  It's
          safe to answer Y if you have the original Windows Sound System card
          made by Microsoft or Aztech SG 16 Pro (or NX16 Pro).  Also you may
          say Y in case your card is NOT among these:

          ATI Stereo F/X, AdLib, Audio Excell DSP16, Cardinal DSP16,
          Ensoniq SoundScape (and compatibles made by Reveal and Spea),
          Gravis Ultrasound, Gravis Ultrasound ACE, Gravis Ultrasound Max,
          Gravis Ultrasound with 16 bit option, Logitech Sound Man 16,
          Logitech SoundMan Games, Logitech SoundMan Wave, MAD16 Pro (OPTi
          82C929), Media Vision Jazz16, MediaTriX AudioTriX Pro, Microsoft
          Windows Sound System (MSS/WSS), Mozart (OAK OTI-601), Orchid
          SW32, Personal Sound System (PSS), Pro Audio Spectrum 16, Pro
          Audio Studio 16, Pro Sonic 16, Roland MPU-401 MIDI interface,
          Sound Blaster 1.0, Sound Blaster 16, Sound Blaster 16ASP, Sound
          Blaster 2.0, Sound Blaster AWE32, Sound Blaster Pro, TI TM4000M
          notebook, ThunderBoard, Turtle Beach Tropez, Yamaha FM
          synthesizers (OPL2, OPL3 and OPL4), 6850 UART MIDI Interface.

          For cards having native support in VoxWare, consult the card
          specific instructions in <file:Documentation/sound/oss/README.OSS>.
          Some drivers have their own MSS support and saying Y to this option
          will cause a conflict.

          If you compile the driver into the kernel, you have to add
          "ad1848=<io>,<irq>,<dma>,<dma2>[,<type>]" to the kernel command
          line.

config SOUND_MPU401
        tristate "MPU-401 support (NOT for SB16)"
        depends on SOUND_OSS
        ---help---
          Be careful with this question.  The MPU401 interface is supported by
          all sound cards.  However, some natively supported cards have their
          own driver for MPU401.  Enabling this MPU401 option with these cards
          will cause a conflict.  Also, enabling MPU401 on a system that
          doesn't really have a MPU401 could cause some trouble.  If your card
          was in the list of supported cards, look at the card specific
          instructions in the <file:Documentation/sound/oss/README.OSS> file.  It
          is safe to answer Y if you have a true MPU401 MIDI interface card.

          If you compile the driver into the kernel, you have to add
          "mpu401=<io>,<irq>" to the kernel command line.

config SOUND_NM256
        tristate "NM256AV/NM256ZX audio support"
        depends on SOUND_OSS
        help
          Say M here to include audio support for the NeoMagic 256AV/256ZX
          chipsets. These are the audio chipsets found in the Sony
          Z505S/SX/DX, some Sony F-series, and the Dell Latitude CPi and CPt
          laptops. It includes support for an AC97-compatible mixer and an
          apparently proprietary sound engine.

          See <file:Documentation/sound/oss/NM256> for further information.

config SOUND_MAD16
        tristate "OPTi MAD16 and/or Mozart based cards"
        depends on SOUND_OSS
        ---help---
          Answer Y if your card has a Mozart (OAK OTI-601) or MAD16 (OPTi
          82C928 or 82C929 or 82C931) audio interface chip. These chips are
          quite common so it's possible that many no-name cards have one of
          them. In addition the MAD16 chip is used in some cards made by known
          manufacturers such as Turtle Beach (Tropez), Reveal (some models)
          and Diamond (latest ones). Note however that the Tropez sound cards
          have their own driver; if you have one of those, say N here and Y or
          M to "Full support for Turtle Beach WaveFront", below.

          If you compile the driver into the kernel, you have to add
          "mad16=<io>,<irq>,<dma>,<dma2>,<mpuio>,<mpuirq>" to the
          kernel command line.

          See also <file:Documentation/sound/oss/Opti> and
          <file:Documentation/sound/oss/MAD16> for more information on setting
          these cards up as modules.

config MAD16_OLDCARD
        bool "Support MIDI in older MAD16 based cards (requires SB)"
        depends on SOUND_MAD16
        help
          Answer Y (or M) if you have an older card based on the C928 or
          Mozart chipset and you want to have MIDI support. If you enable this
          option you also need to enable support for Sound Blaster.

config SOUND_PAS
        tristate "ProAudioSpectrum 16 support"
        depends on SOUND_OSS
        ---help---
          Answer Y only if you have a Pro Audio Spectrum 16, ProAudio Studio
          16 or Logitech SoundMan 16 sound card. Answer N if you have some
          other card made by Media Vision or Logitech since those are not
          PAS16 compatible. Please read <file:Documentation/sound/oss/PAS16>.
          It is not necessary to add Sound Blaster support separately; it
          is included in PAS support.

          If you compile the driver into the kernel, you have to add
          "pas2=<io>,<irq>,<dma>,<dma2>,<sbio>,<sbirq>,<sbdma>,<sbdma2>
          to the kernel command line.

config PAS_JOYSTICK
        bool "Enable PAS16 joystick port"
        depends on SOUND_PAS=y
        help
          Say Y here to enable the Pro Audio Spectrum 16's auxiliary joystick
          port.

config SOUND_PSS
        tristate "PSS (AD1848, ADSP-2115, ESC614) support"
        depends on SOUND_OSS
        help
          Answer Y or M if you have an Orchid SW32, Cardinal DSP16, Beethoven
          ADSP-16 or some other card based on the PSS chipset (AD1848 codec +
          ADSP-2115 DSP chip + Echo ESC614 ASIC CHIP). For more information on
          how to compile it into the kernel or as a module see the file
          <file:Documentation/sound/oss/PSS>.

          If you compile the driver into the kernel, you have to add
          "pss=<io>,<mssio>,<mssirq>,<mssdma>,<mpuio>,<mpuirq>" to the kernel
          command line.

config PSS_MIXER
        bool "Enable PSS mixer (Beethoven ADSP-16 and other compatibile)"
        depends on SOUND_PSS
        help
          Answer Y for Beethoven ADSP-16. You may try to say Y also for other
          cards if they have master volume, bass, treble, and you can't
          control it under Linux. If you answer N for Beethoven ADSP-16, you
          can't control master volume, bass, treble and synth volume.

          If you said M to "PSS support" above, you may enable or disable this
          PSS mixer with the module parameter pss_mixer. For more information
          see the file <file:Documentation/sound/oss/PSS>.

config PSS_HAVE_BOOT
        bool "Have DSPxxx.LD firmware file"
        depends on SOUND_PSS && !STANDALONE
        help
          If you have the DSPxxx.LD file or SYNTH.LD file for you card, say Y
          to include this file. Without this file the synth device (OPL) may
          not work.

config PSS_BOOT_FILE
        string "Full pathname of DSPxxx.LD firmware file"
        depends on PSS_HAVE_BOOT
        default "/etc/sound/dsp001.ld"
        help
          Enter the full pathname of your DSPxxx.LD file or SYNTH.LD file,
          starting from /.

config SOUND_SB
        tristate "100% Sound Blaster compatibles (SB16/32/64, ESS, Jazz16) support"
        depends on SOUND_OSS
        ---help---
          Answer Y if you have an original Sound Blaster card made by Creative
          Labs or a 100% hardware compatible clone (like the Thunderboard or
          SM Games). For an unknown card you may answer Y if the card claims
          to be Sound Blaster-compatible.

          Please read the file <file:Documentation/sound/oss/Soundblaster>.

          You should also say Y here for cards based on the Avance Logic
          ALS-007 and ALS-1X0 chips (read <file:Documentation/sound/oss/ALS>) and
          for cards based on ESS chips (read
          <file:Documentation/sound/oss/ESS1868> and
          <file:Documentation/sound/oss/ESS>). If you have an SB AWE 32 or SB AWE
          64, say Y here and also to "AWE32 synth" below and read
          <file:Documentation/sound/oss/INSTALL.awe>. If you have an IBM Mwave
          card, say Y here and read <file:Documentation/sound/oss/mwave>.

          If you compile the driver into the kernel and don't want to use
          isapnp, you have to add "sb=<io>,<irq>,<dma>,<dma2>" to the kernel
          command line.

          You can say M here to compile this driver as a module; the module is
          called sb.

config SOUND_AWE32_SYNTH
        tristate "AWE32 synth"
        depends on SOUND_OSS
        help
          Say Y here if you have a Sound Blaster SB32, AWE32-PnP, SB AWE64 or
          similar sound card. See <file:Documentation/sound/oss/README.awe>,
          <file:Documentation/sound/oss/AWE32> and the Soundblaster-AWE
          mini-HOWTO, available from <http://www.tldp.org/docs.html#howto>
          for more info.

config SOUND_WAVEFRONT
        tristate "Full support for Turtle Beach WaveFront (Tropez Plus, Tropez, Maui) synth/soundcards"
        depends on SOUND_OSS && m
        help
          Answer Y or M if you have a Tropez Plus, Tropez or Maui sound card
          and read the files <file:Documentation/sound/oss/Wavefront> and
          <file:Documentation/sound/oss/Tropez+>.

config SOUND_MAUI
        tristate "Limited support for Turtle Beach Wave Front (Maui, Tropez) synthesizers"
        depends on SOUND_OSS
        help
          Say Y here if you have a Turtle Beach Wave Front, Maui, or Tropez
          sound card.

          If you compile the driver into the kernel, you have to add
          "maui=<io>,<irq>" to the kernel command line.

config MAUI_HAVE_BOOT
        bool "Have OSWF.MOT firmware file"
        depends on SOUND_MAUI=y && !STANDALONE
        help
          Turtle Beach Maui and Tropez sound cards have a microcontroller
          which needs to be initialized prior to use. OSWF.MOT is a file
          distributed with the card's DOS/Windows drivers. Answer Y if you
          have this file.

config MAUI_BOOT_FILE
        string "Full pathname of OSWF.MOT firmware file"
        depends on MAUI_HAVE_BOOT
        default "/etc/sound/oswf.mot"
        help
          Enter the full pathname of your OSWF.MOT file, starting from /.

config SOUND_YM3812
        tristate "Yamaha FM synthesizer (YM3812/OPL-3) support"
        depends on SOUND_OSS
        ---help---
          Answer Y if your card has a FM chip made by Yamaha (OPL2/OPL3/OPL4).
          Answering Y is usually a safe and recommended choice, however some
          cards may have software (TSR) FM emulation. Enabling FM support with
          these cards may cause trouble (I don't currently know of any such
          cards, however). Please read the file
          <file:Documentation/sound/oss/OPL3> if your card has an OPL3 chip.

          If you compile the driver into the kernel, you have to add
          "opl3=<io>" to the kernel command line.

          If unsure, say Y.

config SOUND_OPL3SA1
        tristate "Yamaha OPL3-SA1 audio controller"
        depends on SOUND_OSS
        help
          Say Y or M if you have a Yamaha OPL3-SA1 sound chip, which is
          usually built into motherboards. Read
          <file:Documentation/sound/oss/OPL3-SA> for details.

          If you compile the driver into the kernel, you have to add
          "opl3sa=<io>,<irq>,<dma>,<dma2>,<mpuio>,<mpuirq>" to the kernel
          command line.

config SOUND_OPL3SA2
        tristate "Yamaha OPL3-SA2 and SA3 based PnP cards"
        depends on SOUND_OSS
        help
          Say Y or M if you have a card based on one of these Yamaha sound
          chipsets or the "SAx", which is actually a SA3. Read
          <file:Documentation/sound/oss/OPL3-SA2> for more information on
          configuring these cards.

          If you compile the driver into the kernel and do not also
          configure in the optional ISA PnP support, you will have to add
          "opl3sa2=<io>,<irq>,<dma>,<dma2>,<mssio>,<mpuio>" to the kernel
          command line.

config SOUND_YMFPCI
        tristate "Yamaha YMF7xx PCI audio (native mode)"
        depends on SOUND_OSS && PCI
        help
          Support for Yamaha cards including the YMF711, YMF715, YMF718,
          YMF719, YMF724, Waveforce 192XG, and Waveforce 192 Digital.

config SOUND_YMFPCI_LEGACY
        bool "Yamaha PCI legacy ports support"
        depends on SOUND_YMFPCI
        help
          Support for YMF7xx PCI cards emulating an MP401.

config SOUND_UART6850
        tristate "6850 UART support"
        depends on SOUND_OSS
        help
          This option enables support for MIDI interfaces based on the 6850
          UART chip. This interface is rarely found on sound cards. It's safe
          to answer N to this question.

          If you compile the driver into the kernel, you have to add
          "uart6850=<io>,<irq>" to the kernel command line.

config SOUND_AEDSP16
        tristate "Gallant Audio Cards (SC-6000 and SC-6600 based)"
        depends on SOUND_OSS
        ---help---
          Answer Y if you have a Gallant's Audio Excel DSP 16 card. This
          driver supports Audio Excel DSP 16 but not the III nor PnP versions
          of this card.

          The Gallant's Audio Excel DSP 16 card can emulate either an SBPro or
          a Microsoft Sound System card, so you should have said Y to either
          "100% Sound Blaster compatibles (SB16/32/64, ESS, Jazz16) support"
          or "Microsoft Sound System support", above, and you need to answer
          the "MSS emulation" and "SBPro emulation" questions below
          accordingly. You should say Y to one and only one of these two
          questions.

          Read the <file:Documentation/sound/oss/README.OSS> file and the head of
          <file:drivers/sound/aedsp16.c> as well as
          <file:Documentation/sound/oss/AudioExcelDSP16> to get more information
          about this driver and its configuration.

config SC6600
        bool "SC-6600 based audio cards (new Audio Excel DSP 16)"
        depends on SOUND_AEDSP16
        help
          The SC6600 is the new version of DSP mounted on the Audio Excel DSP
          16 cards. Find in the manual the FCC ID of your audio card and
          answer Y if you have an SC6600 DSP.

config SC6600_JOY
        bool "Activate SC-6600 Joystick Interface"
        depends on SC6600
        help
          Say Y here in order to use the joystick interface of the Audio Excel
          DSP 16 card.

config SC6600_CDROM
        int "SC-6600 CDROM Interface (4=None, 3=IDE, 1=Panasonic, 0=?Sony?)"
        depends on SC6600
        default "4"
        help
          This is used to activate the CD-ROM interface of the Audio Excel
          DSP 16 card. Enter: 0 for Sony, 1 for Panasonic, 2 for IDE, 4 for no
          CD-ROM present.

config SC6600_CDROMBASE
        hex "SC-6600 CDROM Interface I/O Address"
        depends on SC6600
        default "0"
        help
          Base I/O port address for the CD-ROM interface of the Audio Excel
          DSP 16 card.

choice
        prompt "Audio Excel DSP 16"
        optional
        depends on SOUND_AEDSP16

config AEDSP16_MSS
        bool "MSS emulation"
        depends on SOUND_MSS
        help
          Answer Y if you want your audio card to emulate Microsoft Sound
          System. You should then say Y to "Microsoft Sound System support"
          and say N to "Audio Excel DSP 16 (SBPro emulation)".

config AEDSP16_SBPRO
        bool "SBPro emulation"
        depends on SOUND_SB
        help
          Answer Y if you want your audio card to emulate Sound Blaster Pro.
          You should then say Y to "100% Sound Blaster compatibles
          (SB16/32/64, ESS, Jazz16) support" and N to "Audio Excel DSP 16 (MSS
          emulation)".

          If you compile the driver into the kernel, you have to add
          "aedsp16=<io>,<irq>,<dma>,<mssio>,<mpuio>,<mouirq>" to the kernel
          command line.

endchoice

config AEDSP16_MPU401
        bool "Audio Excel DSP 16 (MPU401 emulation)"
        depends on SOUND_AEDSP16 && SOUND_MPU401
        help
          Answer Y if you want your audio card to emulate the MPU-401 midi
          interface. You should then also say Y to "MPU-401 support".

          Note that the I/O base for MPU-401 support of aedsp16 is the same
          you have selected for "MPU-401 support". If you are using this
          driver as a module you have to specify the MPU I/O base address with
          the parameter 'mpu_base=0xNNN'.

config SOUND_VIDC
        tristate "VIDC 16-bit sound"
        depends on ARM && (ARCH_ACORN || ARCH_CLPS7500) && SOUND_OSS
        help
          16-bit support for the VIDC onboard sound hardware found on Acorn
          machines.

config SOUND_WAVEARTIST
        tristate "Netwinder WaveArtist"
        depends on ARM && SOUND_OSS && ARCH_NETWINDER
        help
          Say Y here to include support for the Rockwell WaveArtist sound
          system.  This driver is mainly for the NetWinder.

config SOUND_TVMIXER
        tristate "TV card (bt848) mixer support"
        depends on SOUND_PRIME && I2C
        help
          Support for audio mixer facilities on the BT848 TV frame-grabber
          card.

config SOUND_KAHLUA
        tristate "XpressAudio Sound Blaster emulation"
        depends on SOUND_SB

config SOUND_ALI5455
        tristate "ALi5455 audio support"
        depends on SOUND_PRIME && PCI

config SOUND_FORTE
        tristate "ForteMedia FM801 driver"
        depends on SOUND_PRIME && PCI
        help
          Say Y or M if you want driver support for the ForteMedia FM801 PCI
          audio controller (Abit AU10, Genius Sound Maker, HP Workstation
          zx2000, and others).

config SOUND_RME96XX
        tristate "RME Hammerfall (RME96XX) support"
        depends on SOUND_PRIME && PCI
        help
          Say Y or M if you have a Hammerfall or Hammerfall light
          multichannel card from RME. If you want to access advanced
          features of the card, read <file:Documentation/sound/oss/rme96xx>.

config SOUND_AD1980
        tristate "AD1980 front/back switch plugin"
        depends on SOUND_PRIME

config SOUND_SH_DAC_AUDIO
        tristate "SuperH DAC audio support"
        depends on SOUND_PRIME && CPU_SH3

config SOUND_SH_DAC_AUDIO_CHANNEL
        int "    DAC channel"
        default "1"
        depends on SOUND_SH_DAC_AUDIO