git.oblomov.eu Git - linux-2.6/blob - drivers/macintosh/therm_pm72.c

   1 /*
   2  * Device driver for the thermostats & fan controller of  the
   3  * Apple G5 "PowerMac7,2" desktop machines.
   4  *
   5  * (c) Copyright IBM Corp. 2003-2004
   6  *
   7  * Maintained by: Benjamin Herrenschmidt
   8  *                <benh@kernel.crashing.org>
   9  *
  10  *
  11  * The algorithm used is the PID control algorithm, used the same
  12  * way the published Darwin code does, using the same values that
  13  * are present in the Darwin 7.0 snapshot property lists.
  14  *
  15  * As far as the CPUs control loops are concerned, I use the
  16  * calibration & PID constants provided by the EEPROM,
  17  * I do _not_ embed any value from the property lists, as the ones
  18  * provided by Darwin 7.0 seem to always have an older version that
  19  * what I've seen on the actual computers.
  20  * It would be interesting to verify that though. Darwin has a
  21  * version code of 1.0.0d11 for all control loops it seems, while
  22  * so far, the machines EEPROMs contain a dataset versioned 1.0.0f
  23  *
  24  * Darwin doesn't provide source to all parts, some missing
  25  * bits like the AppleFCU driver or the actual scale of some
  26  * of the values returned by sensors had to be "guessed" some
  27  * way... or based on what Open Firmware does.
  28  *
  29  * I didn't yet figure out how to get the slots power consumption
  30  * out of the FCU, so that part has not been implemented yet and
  31  * the slots fan is set to a fixed 50% PWM, hoping this value is
  32  * safe enough ...
  33  *
  34  * Note: I have observed strange oscillations of the CPU control
  35  * loop on a dual G5 here. When idle, the CPU exhaust fan tend to
  36  * oscillates slowly (over several minutes) between the minimum
  37  * of 300RPMs and approx. 1000 RPMs. I don't know what is causing
  38  * this, it could be some incorrect constant or an error in the
  39  * way I ported the algorithm, or it could be just normal. I
  40  * don't have full understanding on the way Apple tweaked the PID
  41  * algorithm for the CPU control, it is definitely not a standard
  42  * implementation...
  43  *
  44  * TODO:  - Check MPU structure version/signature
  45  *        - Add things like /sbin/overtemp for non-critical
  46  *          overtemp conditions so userland can take some policy
  47  *          decisions, like slewing down CPUs
  48  *        - Deal with fan and i2c failures in a better way
  49  *        - Maybe do a generic PID based on params used for
  50  *          U3 and Drives ? Definitely need to factor code a bit
  51  *          bettter... also make sensor detection more robust using
  52  *          the device-tree to probe for them
  53  *        - Figure out how to get the slots consumption and set the
  54  *          slots fan accordingly
  55  *
  56  * History:
  57  *
  58  *  Nov. 13, 2003 : 0.5
  59  *      - First release
  60  *
  61  *  Nov. 14, 2003 : 0.6
  62  *      - Read fan speed from FCU, low level fan routines now deal
  63  *        with errors & check fan status, though higher level don't
  64  *        do much.
  65  *      - Move a bunch of definitions to .h file
  66  *
  67  *  Nov. 18, 2003 : 0.7
  68  *      - Fix build on ppc64 kernel
  69  *      - Move back statics definitions to .c file
  70  *      - Avoid calling schedule_timeout with a negative number
  71  *
  72  *  Dec. 18, 2003 : 0.8
  73  *      - Fix typo when reading back fan speed on 2 CPU machines
  74  *
  75  *  Mar. 11, 2004 : 0.9
  76  *      - Rework code accessing the ADC chips, make it more robust and
  77  *        closer to the chip spec. Also make sure it is configured properly,
  78  *        I've seen yet unexplained cases where on startup, I would have stale
  79  *        values in the configuration register
  80  *      - Switch back to use of target fan speed for PID, thus lowering
  81  *        pressure on i2c
  82  *
  83  *  Oct. 20, 2004 : 1.1
  84  *      - Add device-tree lookup for fan IDs, should detect liquid cooling
  85  *        pumps when present
  86  *      - Enable driver for PowerMac7,3 machines
  87  *      - Split the U3/Backside cooling on U3 & U3H versions as Darwin does
  88  *      - Add new CPU cooling algorithm for machines with liquid cooling
  89  *      - Workaround for some PowerMac7,3 with empty "fan" node in the devtree
  90  *      - Fix a signed/unsigned compare issue in some PID loops
  91  *
  92  *  Mar. 10, 2005 : 1.2
  93  *      - Add basic support for Xserve G5
  94  *      - Retreive pumps min/max from EEPROM image in device-tree (broken)
  95  *      - Use min/max macros here or there
  96  *      - Latest darwin updated U3H min fan speed to 20% PWM
  97  *
  98  */
  99
 100 #include <linux/config.h>
 101 #include <linux/types.h>
 102 #include <linux/module.h>
 103 #include <linux/errno.h>
 104 #include <linux/kernel.h>
 105 #include <linux/delay.h>
 106 #include <linux/sched.h>
 107 #include <linux/i2c.h>
 108 #include <linux/slab.h>
 109 #include <linux/init.h>
 110 #include <linux/spinlock.h>
 111 #include <linux/smp_lock.h>
 112 #include <linux/wait.h>
 113 #include <linux/reboot.h>
 114 #include <linux/kmod.h>
 115 #include <linux/i2c.h>
 116 #include <linux/i2c-dev.h>
 117 #include <asm/prom.h>
 118 #include <asm/machdep.h>
 119 #include <asm/io.h>
 120 #include <asm/system.h>
 121 #include <asm/sections.h>
 122 #include <asm/of_device.h>
 123 #include <asm/macio.h>
 124
 125 #include "therm_pm72.h"
 126
 127 #define VERSION "1.2b2"
 128
 129 #undef DEBUG
 130
 131 #ifdef DEBUG
 132 #define DBG(args...)    printk(args)
 133 #else
 134 #define DBG(args...)    do { } while(0)
 135 #endif
 136
 137
 138 /*
 139  * Driver statics
 140  */
 141
 142 static struct of_device *               of_dev;
 143 static struct i2c_adapter *             u3_0;
 144 static struct i2c_adapter *             u3_1;
 145 static struct i2c_adapter *             k2;
 146 static struct i2c_client *              fcu;
 147 static struct cpu_pid_state             cpu_state[2];
 148 static struct basckside_pid_params      backside_params;
 149 static struct backside_pid_state        backside_state;
 150 static struct drives_pid_state          drives_state;
 151 static struct dimm_pid_state            dimms_state;
 152 static int                              state;
 153 static int                              cpu_count;
 154 static int                              cpu_pid_type;
 155 static pid_t                            ctrl_task;
 156 static struct completion                ctrl_complete;
 157 static int                              critical_state;
 158 static int                              rackmac;
 159 static s32                              dimm_output_clamp;
 160
 161 static DECLARE_MUTEX(driver_lock);
 162
 163 /*
 164  * We have 3 types of CPU PID control. One is "split" old style control
 165  * for intake & exhaust fans, the other is "combined" control for both
 166  * CPUs that also deals with the pumps when present. To be "compatible"
 167  * with OS X at this point, we only use "COMBINED" on the machines that
 168  * are identified as having the pumps (though that identification is at
 169  * least dodgy). Ultimately, we could probably switch completely to this
 170  * algorithm provided we hack it to deal with the UP case
 171  */
 172 #define CPU_PID_TYPE_SPLIT      0
 173 #define CPU_PID_TYPE_COMBINED   1
 174 #define CPU_PID_TYPE_RACKMAC    2
 175
 176 /*
 177  * This table describes all fans in the FCU. The "id" and "type" values
 178  * are defaults valid for all earlier machines. Newer machines will
 179  * eventually override the table content based on the device-tree
 180  */
 181 struct fcu_fan_table
 182 {
 183         char*   loc;    /* location code */
 184         int     type;   /* 0 = rpm, 1 = pwm, 2 = pump */
 185         int     id;     /* id or -1 */
 186 };
 187
 188 #define FCU_FAN_RPM             0
 189 #define FCU_FAN_PWM             1
 190
 191 #define FCU_FAN_ABSENT_ID       -1
 192
 193 #define FCU_FAN_COUNT           ARRAY_SIZE(fcu_fans)
 194
 195 struct fcu_fan_table    fcu_fans[] = {
 196         [BACKSIDE_FAN_PWM_INDEX] = {
 197                 .loc    = "BACKSIDE,SYS CTRLR FAN",
 198                 .type   = FCU_FAN_PWM,
 199                 .id     = BACKSIDE_FAN_PWM_DEFAULT_ID,
 200         },
 201         [DRIVES_FAN_RPM_INDEX] = {
 202                 .loc    = "DRIVE BAY",
 203                 .type   = FCU_FAN_RPM,
 204                 .id     = DRIVES_FAN_RPM_DEFAULT_ID,
 205         },
 206         [SLOTS_FAN_PWM_INDEX] = {
 207                 .loc    = "SLOT,PCI FAN",
 208                 .type   = FCU_FAN_PWM,
 209                 .id     = SLOTS_FAN_PWM_DEFAULT_ID,
 210         },
 211         [CPUA_INTAKE_FAN_RPM_INDEX] = {
 212                 .loc    = "CPU A INTAKE",
 213                 .type   = FCU_FAN_RPM,
 214                 .id     = CPUA_INTAKE_FAN_RPM_DEFAULT_ID,
 215         },
 216         [CPUA_EXHAUST_FAN_RPM_INDEX] = {
 217                 .loc    = "CPU A EXHAUST",
 218                 .type   = FCU_FAN_RPM,
 219                 .id     = CPUA_EXHAUST_FAN_RPM_DEFAULT_ID,
 220         },
 221         [CPUB_INTAKE_FAN_RPM_INDEX] = {
 222                 .loc    = "CPU B INTAKE",
 223                 .type   = FCU_FAN_RPM,
 224                 .id     = CPUB_INTAKE_FAN_RPM_DEFAULT_ID,
 225         },
 226         [CPUB_EXHAUST_FAN_RPM_INDEX] = {
 227                 .loc    = "CPU B EXHAUST",
 228                 .type   = FCU_FAN_RPM,
 229                 .id     = CPUB_EXHAUST_FAN_RPM_DEFAULT_ID,
 230         },
 231         /* pumps aren't present by default, have to be looked up in the
 232          * device-tree
 233          */
 234         [CPUA_PUMP_RPM_INDEX] = {
 235                 .loc    = "CPU A PUMP",
 236                 .type   = FCU_FAN_RPM,
 237                 .id     = FCU_FAN_ABSENT_ID,
 238         },
 239         [CPUB_PUMP_RPM_INDEX] = {
 240                 .loc    = "CPU B PUMP",
 241                 .type   = FCU_FAN_RPM,
 242                 .id     = FCU_FAN_ABSENT_ID,
 243         },
 244         /* Xserve fans */
 245         [CPU_A1_FAN_RPM_INDEX] = {
 246                 .loc    = "CPU A 1",
 247                 .type   = FCU_FAN_RPM,
 248                 .id     = FCU_FAN_ABSENT_ID,
 249         },
 250         [CPU_A2_FAN_RPM_INDEX] = {
 251                 .loc    = "CPU A 2",
 252                 .type   = FCU_FAN_RPM,
 253                 .id     = FCU_FAN_ABSENT_ID,
 254         },
 255         [CPU_A3_FAN_RPM_INDEX] = {
 256                 .loc    = "CPU A 3",
 257                 .type   = FCU_FAN_RPM,
 258                 .id     = FCU_FAN_ABSENT_ID,
 259         },
 260         [CPU_B1_FAN_RPM_INDEX] = {
 261                 .loc    = "CPU B 1",
 262                 .type   = FCU_FAN_RPM,
 263                 .id     = FCU_FAN_ABSENT_ID,
 264         },
 265         [CPU_B2_FAN_RPM_INDEX] = {
 266                 .loc    = "CPU B 2",
 267                 .type   = FCU_FAN_RPM,
 268                 .id     = FCU_FAN_ABSENT_ID,
 269         },
 270         [CPU_B3_FAN_RPM_INDEX] = {
 271                 .loc    = "CPU B 3",
 272                 .type   = FCU_FAN_RPM,
 273                 .id     = FCU_FAN_ABSENT_ID,
 274         },
 275 };
 276
 277 /*
 278  * i2c_driver structure to attach to the host i2c controller
 279  */
 280
 281 static int therm_pm72_attach(struct i2c_adapter *adapter);
 282 static int therm_pm72_detach(struct i2c_adapter *adapter);
 283
 284 static struct i2c_driver therm_pm72_driver =
 285 {
 286         .driver = {
 287                 .name   = "therm_pm72",
 288         },
 289         .attach_adapter = therm_pm72_attach,
 290         .detach_adapter = therm_pm72_detach,
 291 };
 292
 293 /*
 294  * Utility function to create an i2c_client structure and
 295  * attach it to one of u3 adapters
 296  */
 297 static struct i2c_client *attach_i2c_chip(int id, const char *name)
 298 {
 299         struct i2c_client *clt;
 300         struct i2c_adapter *adap;
 301
 302         if (id & 0x200)
 303                 adap = k2;
 304         else if (id & 0x100)
 305                 adap = u3_1;
 306         else
 307                 adap = u3_0;
 308         if (adap == NULL)
 309                 return NULL;
 310
 311         clt = kmalloc(sizeof(struct i2c_client), GFP_KERNEL);
 312         if (clt == NULL)
 313                 return NULL;
 314         memset(clt, 0, sizeof(struct i2c_client));
 315
 316         clt->addr = (id >> 1) & 0x7f;
 317         clt->adapter = adap;
 318         clt->driver = &therm_pm72_driver;
 319         strncpy(clt->name, name, I2C_NAME_SIZE-1);
 320
 321         if (i2c_attach_client(clt)) {
 322                 printk(KERN_ERR "therm_pm72: Failed to attach to i2c ID 0x%x\n", id);
 323                 kfree(clt);
 324                 return NULL;
 325         }
 326         return clt;
 327 }
 328
 329 /*
 330  * Utility function to get rid of the i2c_client structure
 331  * (will also detach from the adapter hopepfully)
 332  */
 333 static void detach_i2c_chip(struct i2c_client *clt)
 334 {
 335         i2c_detach_client(clt);
 336         kfree(clt);
 337 }
 338
 339 /*
 340  * Here are the i2c chip access wrappers
 341  */
 342
 343 static void initialize_adc(struct cpu_pid_state *state)
 344 {
 345         int rc;
 346         u8 buf[2];
 347
 348         /* Read ADC the configuration register and cache it. We
 349          * also make sure Config2 contains proper values, I've seen
 350          * cases where we got stale grabage in there, thus preventing
 351          * proper reading of conv. values
 352          */
 353
 354         /* Clear Config2 */
 355         buf[0] = 5;
 356         buf[1] = 0;
 357         i2c_master_send(state->monitor, buf, 2);
 358
 359         /* Read & cache Config1 */
 360         buf[0] = 1;
 361         rc = i2c_master_send(state->monitor, buf, 1);
 362         if (rc > 0) {
 363                 rc = i2c_master_recv(state->monitor, buf, 1);
 364                 if (rc > 0) {
 365                         state->adc_config = buf[0];
 366                         DBG("ADC config reg: %02x\n", state->adc_config);
 367                         /* Disable shutdown mode */
 368                         state->adc_config &= 0xfe;
 369                         buf[0] = 1;
 370                         buf[1] = state->adc_config;
 371                         rc = i2c_master_send(state->monitor, buf, 2);
 372                 }
 373         }
 374         if (rc <= 0)
 375                 printk(KERN_ERR "therm_pm72: Error reading ADC config"
 376                        " register !\n");
 377 }
 378
 379 static int read_smon_adc(struct cpu_pid_state *state, int chan)
 380 {
 381         int rc, data, tries = 0;
 382         u8 buf[2];
 383
 384         for (;;) {
 385                 /* Set channel */
 386                 buf[0] = 1;
 387                 buf[1] = (state->adc_config & 0x1f) | (chan << 5);
 388                 rc = i2c_master_send(state->monitor, buf, 2);
 389                 if (rc <= 0)
 390                         goto error;
 391                 /* Wait for convertion */
 392                 msleep(1);
 393                 /* Switch to data register */
 394                 buf[0] = 4;
 395                 rc = i2c_master_send(state->monitor, buf, 1);
 396                 if (rc <= 0)
 397                         goto error;
 398                 /* Read result */
 399                 rc = i2c_master_recv(state->monitor, buf, 2);
 400                 if (rc < 0)
 401                         goto error;
 402                 data = ((u16)buf[0]) << 8 | (u16)buf[1];
 403                 return data >> 6;
 404         error:
 405                 DBG("Error reading ADC, retrying...\n");
 406                 if (++tries > 10) {
 407                         printk(KERN_ERR "therm_pm72: Error reading ADC !\n");
 408                         return -1;
 409                 }
 410                 msleep(10);
 411         }
 412 }
 413
 414 static int read_lm87_reg(struct i2c_client * chip, int reg)
 415 {
 416         int rc, tries = 0;
 417         u8 buf;
 418
 419         for (;;) {
 420                 /* Set address */
 421                 buf = (u8)reg;
 422                 rc = i2c_master_send(chip, &buf, 1);
 423                 if (rc <= 0)
 424                         goto error;
 425                 rc = i2c_master_recv(chip, &buf, 1);
 426                 if (rc <= 0)
 427                         goto error;
 428                 return (int)buf;
 429         error:
 430                 DBG("Error reading LM87, retrying...\n");
 431                 if (++tries > 10) {
 432                         printk(KERN_ERR "therm_pm72: Error reading LM87 !\n");
 433                         return -1;
 434                 }
 435                 msleep(10);
 436         }
 437 }
 438
 439 static int fan_read_reg(int reg, unsigned char *buf, int nb)
 440 {
 441         int tries, nr, nw;
 442
 443         buf[0] = reg;
 444         tries = 0;
 445         for (;;) {
 446                 nw = i2c_master_send(fcu, buf, 1);
 447                 if (nw > 0 || (nw < 0 && nw != -EIO) || tries >= 100)
 448                         break;
 449                 msleep(10);
 450                 ++tries;
 451         }
 452         if (nw <= 0) {
 453                 printk(KERN_ERR "Failure writing address to FCU: %d", nw);
 454                 return -EIO;
 455         }
 456         tries = 0;
 457         for (;;) {
 458                 nr = i2c_master_recv(fcu, buf, nb);
 459                 if (nr > 0 || (nr < 0 && nr != ENODEV) || tries >= 100)
 460                         break;
 461                 msleep(10);
 462                 ++tries;
 463         }
 464         if (nr <= 0)
 465                 printk(KERN_ERR "Failure reading data from FCU: %d", nw);
 466         return nr;
 467 }
 468
 469 static int fan_write_reg(int reg, const unsigned char *ptr, int nb)
 470 {
 471         int tries, nw;
 472         unsigned char buf[16];
 473
 474         buf[0] = reg;
 475         memcpy(buf+1, ptr, nb);
 476         ++nb;
 477         tries = 0;
 478         for (;;) {
 479                 nw = i2c_master_send(fcu, buf, nb);
 480                 if (nw > 0 || (nw < 0 && nw != EIO) || tries >= 100)
 481                         break;
 482                 msleep(10);
 483                 ++tries;
 484         }
 485         if (nw < 0)
 486                 printk(KERN_ERR "Failure writing to FCU: %d", nw);
 487         return nw;
 488 }
 489
 490 static int start_fcu(void)
 491 {
 492         unsigned char buf = 0xff;
 493         int rc;
 494
 495         rc = fan_write_reg(0xe, &buf, 1);
 496         if (rc < 0)
 497                 return -EIO;
 498         rc = fan_write_reg(0x2e, &buf, 1);
 499         if (rc < 0)
 500                 return -EIO;
 501         return 0;
 502 }
 503
 504 static int set_rpm_fan(int fan_index, int rpm)
 505 {
 506         unsigned char buf[2];
 507         int rc, id;
 508
 509         if (fcu_fans[fan_index].type != FCU_FAN_RPM)
 510                 return -EINVAL;
 511         id = fcu_fans[fan_index].id;
 512         if (id == FCU_FAN_ABSENT_ID)
 513                 return -EINVAL;
 514
 515         if (rpm < 300)
 516                 rpm = 300;
 517         else if (rpm > 8191)
 518                 rpm = 8191;
 519         buf[0] = rpm >> 5;
 520         buf[1] = rpm << 3;
 521         rc = fan_write_reg(0x10 + (id * 2), buf, 2);
 522         if (rc < 0)
 523                 return -EIO;
 524         return 0;
 525 }
 526
 527 static int get_rpm_fan(int fan_index, int programmed)
 528 {
 529         unsigned char failure;
 530         unsigned char active;
 531         unsigned char buf[2];
 532         int rc, id, reg_base;
 533
 534         if (fcu_fans[fan_index].type != FCU_FAN_RPM)
 535                 return -EINVAL;
 536         id = fcu_fans[fan_index].id;
 537         if (id == FCU_FAN_ABSENT_ID)
 538                 return -EINVAL;
 539
 540         rc = fan_read_reg(0xb, &failure, 1);
 541         if (rc != 1)
 542                 return -EIO;
 543         if ((failure & (1 << id)) != 0)
 544                 return -EFAULT;
 545         rc = fan_read_reg(0xd, &active, 1);
 546         if (rc != 1)
 547                 return -EIO;
 548         if ((active & (1 << id)) == 0)
 549                 return -ENXIO;
 550
 551         /* Programmed value or real current speed */
 552         reg_base = programmed ? 0x10 : 0x11;
 553         rc = fan_read_reg(reg_base + (id * 2), buf, 2);
 554         if (rc != 2)
 555                 return -EIO;
 556
 557         return (buf[0] << 5) | buf[1] >> 3;
 558 }
 559
 560 static int set_pwm_fan(int fan_index, int pwm)
 561 {
 562         unsigned char buf[2];
 563         int rc, id;
 564
 565         if (fcu_fans[fan_index].type != FCU_FAN_PWM)
 566                 return -EINVAL;
 567         id = fcu_fans[fan_index].id;
 568         if (id == FCU_FAN_ABSENT_ID)
 569                 return -EINVAL;
 570
 571         if (pwm < 10)
 572                 pwm = 10;
 573         else if (pwm > 100)
 574                 pwm = 100;
 575         pwm = (pwm * 2559) / 1000;
 576         buf[0] = pwm;
 577         rc = fan_write_reg(0x30 + (id * 2), buf, 1);
 578         if (rc < 0)
 579                 return rc;
 580         return 0;
 581 }
 582
 583 static int get_pwm_fan(int fan_index)
 584 {
 585         unsigned char failure;
 586         unsigned char active;
 587         unsigned char buf[2];
 588         int rc, id;
 589
 590         if (fcu_fans[fan_index].type != FCU_FAN_PWM)
 591                 return -EINVAL;
 592         id = fcu_fans[fan_index].id;
 593         if (id == FCU_FAN_ABSENT_ID)
 594                 return -EINVAL;
 595
 596         rc = fan_read_reg(0x2b, &failure, 1);
 597         if (rc != 1)
 598                 return -EIO;
 599         if ((failure & (1 << id)) != 0)
 600                 return -EFAULT;
 601         rc = fan_read_reg(0x2d, &active, 1);
 602         if (rc != 1)
 603                 return -EIO;
 604         if ((active & (1 << id)) == 0)
 605                 return -ENXIO;
 606
 607         /* Programmed value or real current speed */
 608         rc = fan_read_reg(0x30 + (id * 2), buf, 1);
 609         if (rc != 1)
 610                 return -EIO;
 611
 612         return (buf[0] * 1000) / 2559;
 613 }
 614
 615 /*
 616  * Utility routine to read the CPU calibration EEPROM data
 617  * from the device-tree
 618  */
 619 static int read_eeprom(int cpu, struct mpu_data *out)
 620 {
 621         struct device_node *np;
 622         char nodename[64];
 623         u8 *data;
 624         int len;
 625
 626         /* prom.c routine for finding a node by path is a bit brain dead
 627          * and requires exact @xxx unit numbers. This is a bit ugly but
 628          * will work for these machines
 629          */
 630         sprintf(nodename, "/u3@0,f8000000/i2c@f8001000/cpuid@a%d", cpu ? 2 : 0);
 631         np = of_find_node_by_path(nodename);
 632         if (np == NULL) {
 633                 printk(KERN_ERR "therm_pm72: Failed to retreive cpuid node from device-tree\n");
 634                 return -ENODEV;
 635         }
 636         data = (u8 *)get_property(np, "cpuid", &len);
 637         if (data == NULL) {
 638                 printk(KERN_ERR "therm_pm72: Failed to retreive cpuid property from device-tree\n");
 639                 of_node_put(np);
 640                 return -ENODEV;
 641         }
 642         memcpy(out, data, sizeof(struct mpu_data));
 643         of_node_put(np);
 644
 645         return 0;
 646 }
 647
 648 static void fetch_cpu_pumps_minmax(void)
 649 {
 650         struct cpu_pid_state *state0 = &cpu_state[0];
 651         struct cpu_pid_state *state1 = &cpu_state[1];
 652         u16 pump_min = 0, pump_max = 0xffff;
 653         u16 tmp[4];
 654
 655         /* Try to fetch pumps min/max infos from eeprom */
 656
 657         memcpy(&tmp, &state0->mpu.processor_part_num, 8);
 658         if (tmp[0] != 0xffff && tmp[1] != 0xffff) {
 659                 pump_min = max(pump_min, tmp[0]);
 660                 pump_max = min(pump_max, tmp[1]);
 661         }
 662         if (tmp[2] != 0xffff && tmp[3] != 0xffff) {
 663                 pump_min = max(pump_min, tmp[2]);
 664                 pump_max = min(pump_max, tmp[3]);
 665         }
 666
 667         /* Double check the values, this _IS_ needed as the EEPROM on
 668          * some dual 2.5Ghz G5s seem, at least, to have both min & max
 669          * same to the same value ... (grrrr)
 670          */
 671         if (pump_min == pump_max || pump_min == 0 || pump_max == 0xffff) {
 672                 pump_min = CPU_PUMP_OUTPUT_MIN;
 673                 pump_max = CPU_PUMP_OUTPUT_MAX;
 674         }
 675
 676         state0->pump_min = state1->pump_min = pump_min;
 677         state0->pump_max = state1->pump_max = pump_max;
 678 }
 679
 680 /*
 681  * Now, unfortunately, sysfs doesn't give us a nice void * we could
 682  * pass around to the attribute functions, so we don't really have
 683  * choice but implement a bunch of them...
 684  *
 685  * That sucks a bit, we take the lock because FIX32TOPRINT evaluates
 686  * the input twice... I accept patches :)
 687  */
 688 #define BUILD_SHOW_FUNC_FIX(name, data)                         \
 689 static ssize_t show_##name(struct device *dev, struct device_attribute *attr, char *buf)        \
 690 {                                                               \
 691         ssize_t r;                                              \
 692         down(&driver_lock);                                     \
 693         r = sprintf(buf, "%d.%03d", FIX32TOPRINT(data));        \
 694         up(&driver_lock);                                       \
 695         return r;                                               \
 696 }
 697 #define BUILD_SHOW_FUNC_INT(name, data)                         \
 698 static ssize_t show_##name(struct device *dev, struct device_attribute *attr, char *buf)        \
 699 {                                                               \
 700         return sprintf(buf, "%d", data);                        \
 701 }
 702
 703 BUILD_SHOW_FUNC_FIX(cpu0_temperature, cpu_state[0].last_temp)
 704 BUILD_SHOW_FUNC_FIX(cpu0_voltage, cpu_state[0].voltage)
 705 BUILD_SHOW_FUNC_FIX(cpu0_current, cpu_state[0].current_a)
 706 BUILD_SHOW_FUNC_INT(cpu0_exhaust_fan_rpm, cpu_state[0].rpm)
 707 BUILD_SHOW_FUNC_INT(cpu0_intake_fan_rpm, cpu_state[0].intake_rpm)
 708
 709 BUILD_SHOW_FUNC_FIX(cpu1_temperature, cpu_state[1].last_temp)
 710 BUILD_SHOW_FUNC_FIX(cpu1_voltage, cpu_state[1].voltage)
 711 BUILD_SHOW_FUNC_FIX(cpu1_current, cpu_state[1].current_a)
 712 BUILD_SHOW_FUNC_INT(cpu1_exhaust_fan_rpm, cpu_state[1].rpm)
 713 BUILD_SHOW_FUNC_INT(cpu1_intake_fan_rpm, cpu_state[1].intake_rpm)
 714
 715 BUILD_SHOW_FUNC_FIX(backside_temperature, backside_state.last_temp)
 716 BUILD_SHOW_FUNC_INT(backside_fan_pwm, backside_state.pwm)
 717
 718 BUILD_SHOW_FUNC_FIX(drives_temperature, drives_state.last_temp)
 719 BUILD_SHOW_FUNC_INT(drives_fan_rpm, drives_state.rpm)
 720
 721 BUILD_SHOW_FUNC_FIX(dimms_temperature, dimms_state.last_temp)
 722
 723 static DEVICE_ATTR(cpu0_temperature,S_IRUGO,show_cpu0_temperature,NULL);
 724 static DEVICE_ATTR(cpu0_voltage,S_IRUGO,show_cpu0_voltage,NULL);
 725 static DEVICE_ATTR(cpu0_current,S_IRUGO,show_cpu0_current,NULL);
 726 static DEVICE_ATTR(cpu0_exhaust_fan_rpm,S_IRUGO,show_cpu0_exhaust_fan_rpm,NULL);
 727 static DEVICE_ATTR(cpu0_intake_fan_rpm,S_IRUGO,show_cpu0_intake_fan_rpm,NULL);
 728
 729 static DEVICE_ATTR(cpu1_temperature,S_IRUGO,show_cpu1_temperature,NULL);
 730 static DEVICE_ATTR(cpu1_voltage,S_IRUGO,show_cpu1_voltage,NULL);
 731 static DEVICE_ATTR(cpu1_current,S_IRUGO,show_cpu1_current,NULL);
 732 static DEVICE_ATTR(cpu1_exhaust_fan_rpm,S_IRUGO,show_cpu1_exhaust_fan_rpm,NULL);
 733 static DEVICE_ATTR(cpu1_intake_fan_rpm,S_IRUGO,show_cpu1_intake_fan_rpm,NULL);
 734
 735 static DEVICE_ATTR(backside_temperature,S_IRUGO,show_backside_temperature,NULL);
 736 static DEVICE_ATTR(backside_fan_pwm,S_IRUGO,show_backside_fan_pwm,NULL);
 737
 738 static DEVICE_ATTR(drives_temperature,S_IRUGO,show_drives_temperature,NULL);
 739 static DEVICE_ATTR(drives_fan_rpm,S_IRUGO,show_drives_fan_rpm,NULL);
 740
 741 static DEVICE_ATTR(dimms_temperature,S_IRUGO,show_dimms_temperature,NULL);
 742
 743 /*
 744  * CPUs fans control loop
 745  */
 746
 747 static int do_read_one_cpu_values(struct cpu_pid_state *state, s32 *temp, s32 *power)
 748 {
 749         s32 ltemp, volts, amps;
 750         int index, rc = 0;
 751
 752         /* Default (in case of error) */
 753         *temp = state->cur_temp;
 754         *power = state->cur_power;
 755
 756         if (cpu_pid_type == CPU_PID_TYPE_RACKMAC)
 757                 index = (state->index == 0) ?
 758                         CPU_A1_FAN_RPM_INDEX : CPU_B1_FAN_RPM_INDEX;
 759         else
 760                 index = (state->index == 0) ?
 761                         CPUA_EXHAUST_FAN_RPM_INDEX : CPUB_EXHAUST_FAN_RPM_INDEX;
 762
 763         /* Read current fan status */
 764         rc = get_rpm_fan(index, !RPM_PID_USE_ACTUAL_SPEED);
 765         if (rc < 0) {
 766                 /* XXX What do we do now ? Nothing for now, keep old value, but
 767                  * return error upstream
 768                  */
 769                 DBG("  cpu %d, fan reading error !\n", state->index);
 770         } else {
 771                 state->rpm = rc;
 772                 DBG("  cpu %d, exhaust RPM: %d\n", state->index, state->rpm);
 773         }
 774
 775         /* Get some sensor readings and scale it */
 776         ltemp = read_smon_adc(state, 1);
 777         if (ltemp == -1) {
 778                 /* XXX What do we do now ? */
 779                 state->overtemp++;
 780                 if (rc == 0)
 781                         rc = -EIO;
 782                 DBG("  cpu %d, temp reading error !\n", state->index);
 783         } else {
 784                 /* Fixup temperature according to diode calibration
 785                  */
 786                 DBG("  cpu %d, temp raw: %04x, m_diode: %04x, b_diode: %04x\n",
 787                     state->index,
 788                     ltemp, state->mpu.mdiode, state->mpu.bdiode);
 789                 *temp = ((s32)ltemp * (s32)state->mpu.mdiode + ((s32)state->mpu.bdiode << 12)) >> 2;
 790                 state->last_temp = *temp;
 791                 DBG("  temp: %d.%03d\n", FIX32TOPRINT((*temp)));
 792         }
 793
 794         /*
 795          * Read voltage & current and calculate power
 796          */
 797         volts = read_smon_adc(state, 3);
 798         amps = read_smon_adc(state, 4);
 799
 800         /* Scale voltage and current raw sensor values according to fixed scales
 801          * obtained in Darwin and calculate power from I and V
 802          */
 803         volts *= ADC_CPU_VOLTAGE_SCALE;
 804         amps *= ADC_CPU_CURRENT_SCALE;
 805         *power = (((u64)volts) * ((u64)amps)) >> 16;
 806         state->voltage = volts;
 807         state->current_a = amps;
 808         state->last_power = *power;
 809
 810         DBG("  cpu %d, current: %d.%03d, voltage: %d.%03d, power: %d.%03d W\n",
 811             state->index, FIX32TOPRINT(state->current_a),
 812             FIX32TOPRINT(state->voltage), FIX32TOPRINT(*power));
 813
 814         return 0;
 815 }
 816
 817 static void do_cpu_pid(struct cpu_pid_state *state, s32 temp, s32 power)
 818 {
 819         s32 power_target, integral, derivative, proportional, adj_in_target, sval;
 820         s64 integ_p, deriv_p, prop_p, sum;
 821         int i;
 822
 823         /* Calculate power target value (could be done once for all)
 824          * and convert to a 16.16 fp number
 825          */
 826         power_target = ((u32)(state->mpu.pmaxh - state->mpu.padjmax)) << 16;
 827         DBG("  power target: %d.%03d, error: %d.%03d\n",
 828             FIX32TOPRINT(power_target), FIX32TOPRINT(power_target - power));
 829
 830         /* Store temperature and power in history array */
 831         state->cur_temp = (state->cur_temp + 1) % CPU_TEMP_HISTORY_SIZE;
 832         state->temp_history[state->cur_temp] = temp;
 833         state->cur_power = (state->cur_power + 1) % state->count_power;
 834         state->power_history[state->cur_power] = power;
 835         state->error_history[state->cur_power] = power_target - power;
 836
 837         /* If first loop, fill the history table */
 838         if (state->first) {
 839                 for (i = 0; i < (state->count_power - 1); i++) {
 840                         state->cur_power = (state->cur_power + 1) % state->count_power;
 841                         state->power_history[state->cur_power] = power;
 842                         state->error_history[state->cur_power] = power_target - power;
 843                 }
 844                 for (i = 0; i < (CPU_TEMP_HISTORY_SIZE - 1); i++) {
 845                         state->cur_temp = (state->cur_temp + 1) % CPU_TEMP_HISTORY_SIZE;
 846                         state->temp_history[state->cur_temp] = temp;
 847                 }
 848                 state->first = 0;
 849         }
 850
 851         /* Calculate the integral term normally based on the "power" values */
 852         sum = 0;
 853         integral = 0;
 854         for (i = 0; i < state->count_power; i++)
 855                 integral += state->error_history[i];
 856         integral *= CPU_PID_INTERVAL;
 857         DBG("  integral: %08x\n", integral);
 858
 859         /* Calculate the adjusted input (sense value).
 860          *   G_r is 12.20
 861          *   integ is 16.16
 862          *   so the result is 28.36
 863          *
 864          * input target is mpu.ttarget, input max is mpu.tmax
 865          */
 866         integ_p = ((s64)state->mpu.pid_gr) * (s64)integral;
 867         DBG("   integ_p: %d\n", (int)(integ_p >> 36));
 868         sval = (state->mpu.tmax << 16) - ((integ_p >> 20) & 0xffffffff);
 869         adj_in_target = (state->mpu.ttarget << 16);
 870         if (adj_in_target > sval)
 871                 adj_in_target = sval;
 872         DBG("   adj_in_target: %d.%03d, ttarget: %d\n", FIX32TOPRINT(adj_in_target),
 873             state->mpu.ttarget);
 874
 875         /* Calculate the derivative term */
 876         derivative = state->temp_history[state->cur_temp] -
 877                 state->temp_history[(state->cur_temp + CPU_TEMP_HISTORY_SIZE - 1)
 878                                     % CPU_TEMP_HISTORY_SIZE];
 879         derivative /= CPU_PID_INTERVAL;
 880         deriv_p = ((s64)state->mpu.pid_gd) * (s64)derivative;
 881         DBG("   deriv_p: %d\n", (int)(deriv_p >> 36));
 882         sum += deriv_p;
 883
 884         /* Calculate the proportional term */
 885         proportional = temp - adj_in_target;
 886         prop_p = ((s64)state->mpu.pid_gp) * (s64)proportional;
 887         DBG("   prop_p: %d\n", (int)(prop_p >> 36));
 888         sum += prop_p;
 889
 890         /* Scale sum */
 891         sum >>= 36;
 892
 893         DBG("   sum: %d\n", (int)sum);
 894         state->rpm += (s32)sum;
 895 }
 896
 897 static void do_monitor_cpu_combined(void)
 898 {
 899         struct cpu_pid_state *state0 = &cpu_state[0];
 900         struct cpu_pid_state *state1 = &cpu_state[1];
 901         s32 temp0, power0, temp1, power1;
 902         s32 temp_combi, power_combi;
 903         int rc, intake, pump;
 904
 905         rc = do_read_one_cpu_values(state0, &temp0, &power0);
 906         if (rc < 0) {
 907                 /* XXX What do we do now ? */
 908         }
 909         state1->overtemp = 0;
 910         rc = do_read_one_cpu_values(state1, &temp1, &power1);
 911         if (rc < 0) {
 912                 /* XXX What do we do now ? */
 913         }
 914         if (state1->overtemp)
 915                 state0->overtemp++;
 916
 917         temp_combi = max(temp0, temp1);
 918         power_combi = max(power0, power1);
 919
 920         /* Check tmax, increment overtemp if we are there. At tmax+8, we go
 921          * full blown immediately and try to trigger a shutdown
 922          */
 923         if (temp_combi >= ((state0->mpu.tmax + 8) << 16)) {
 924                 printk(KERN_WARNING "Warning ! Temperature way above maximum (%d) !\n",
 925                        temp_combi >> 16);
 926                 state0->overtemp += CPU_MAX_OVERTEMP / 4;
 927         } else if (temp_combi > (state0->mpu.tmax << 16))
 928                 state0->overtemp++;
 929         else
 930                 state0->overtemp = 0;
 931         if (state0->overtemp >= CPU_MAX_OVERTEMP)
 932                 critical_state = 1;
 933         if (state0->overtemp > 0) {
 934                 state0->rpm = state0->mpu.rmaxn_exhaust_fan;
 935                 state0->intake_rpm = intake = state0->mpu.rmaxn_intake_fan;
 936                 pump = state0->pump_max;
 937                 goto do_set_fans;
 938         }
 939
 940         /* Do the PID */
 941         do_cpu_pid(state0, temp_combi, power_combi);
 942
 943         /* Range check */
 944         state0->rpm = max(state0->rpm, (int)state0->mpu.rminn_exhaust_fan);
 945         state0->rpm = min(state0->rpm, (int)state0->mpu.rmaxn_exhaust_fan);
 946
 947         /* Calculate intake fan speed */
 948         intake = (state0->rpm * CPU_INTAKE_SCALE) >> 16;
 949         intake = max(intake, (int)state0->mpu.rminn_intake_fan);
 950         intake = min(intake, (int)state0->mpu.rmaxn_intake_fan);
 951         state0->intake_rpm = intake;
 952
 953         /* Calculate pump speed */
 954         pump = (state0->rpm * state0->pump_max) /
 955                 state0->mpu.rmaxn_exhaust_fan;
 956         pump = min(pump, state0->pump_max);
 957         pump = max(pump, state0->pump_min);
 958
 959  do_set_fans:
 960         /* We copy values from state 0 to state 1 for /sysfs */
 961         state1->rpm = state0->rpm;
 962         state1->intake_rpm = state0->intake_rpm;
 963
 964         DBG("** CPU %d RPM: %d Ex, %d, Pump: %d, In, overtemp: %d\n",
 965             state1->index, (int)state1->rpm, intake, pump, state1->overtemp);
 966
 967         /* We should check for errors, shouldn't we ? But then, what
 968          * do we do once the error occurs ? For FCU notified fan
 969          * failures (-EFAULT) we probably want to notify userland
 970          * some way...
 971          */
 972         set_rpm_fan(CPUA_INTAKE_FAN_RPM_INDEX, intake);
 973         set_rpm_fan(CPUA_EXHAUST_FAN_RPM_INDEX, state0->rpm);
 974         set_rpm_fan(CPUB_INTAKE_FAN_RPM_INDEX, intake);
 975         set_rpm_fan(CPUB_EXHAUST_FAN_RPM_INDEX, state0->rpm);
 976
 977         if (fcu_fans[CPUA_PUMP_RPM_INDEX].id != FCU_FAN_ABSENT_ID)
 978                 set_rpm_fan(CPUA_PUMP_RPM_INDEX, pump);
 979         if (fcu_fans[CPUB_PUMP_RPM_INDEX].id != FCU_FAN_ABSENT_ID)
 980                 set_rpm_fan(CPUB_PUMP_RPM_INDEX, pump);
 981 }
 982
 983 static void do_monitor_cpu_split(struct cpu_pid_state *state)
 984 {
 985         s32 temp, power;
 986         int rc, intake;
 987
 988         /* Read current fan status */
 989         rc = do_read_one_cpu_values(state, &temp, &power);
 990         if (rc < 0) {
 991                 /* XXX What do we do now ? */
 992         }
 993
 994         /* Check tmax, increment overtemp if we are there. At tmax+8, we go
 995          * full blown immediately and try to trigger a shutdown
 996          */
 997         if (temp >= ((state->mpu.tmax + 8) << 16)) {
 998                 printk(KERN_WARNING "Warning ! CPU %d temperature way above maximum"
 999                        " (%d) !\n",
1000                        state->index, temp >> 16);
1001                 state->overtemp += CPU_MAX_OVERTEMP / 4;
1002         } else if (temp > (state->mpu.tmax << 16))
1003                 state->overtemp++;
1004         else
1005                 state->overtemp = 0;
1006         if (state->overtemp >= CPU_MAX_OVERTEMP)
1007                 critical_state = 1;
1008         if (state->overtemp > 0) {
1009                 state->rpm = state->mpu.rmaxn_exhaust_fan;
1010                 state->intake_rpm = intake = state->mpu.rmaxn_intake_fan;
1011                 goto do_set_fans;
1012         }
1013
1014         /* Do the PID */
1015         do_cpu_pid(state, temp, power);
1016
1017         /* Range check */
1018         state->rpm = max(state->rpm, (int)state->mpu.rminn_exhaust_fan);
1019         state->rpm = min(state->rpm, (int)state->mpu.rmaxn_exhaust_fan);
1020
1021         /* Calculate intake fan */
1022         intake = (state->rpm * CPU_INTAKE_SCALE) >> 16;
1023         intake = max(intake, (int)state->mpu.rminn_intake_fan);
1024         intake = min(intake, (int)state->mpu.rmaxn_intake_fan);
1025         state->intake_rpm = intake;
1026
1027  do_set_fans:
1028         DBG("** CPU %d RPM: %d Ex, %d In, overtemp: %d\n",
1029             state->index, (int)state->rpm, intake, state->overtemp);
1030
1031         /* We should check for errors, shouldn't we ? But then, what
1032          * do we do once the error occurs ? For FCU notified fan
1033          * failures (-EFAULT) we probably want to notify userland
1034          * some way...
1035          */
1036         if (state->index == 0) {
1037                 set_rpm_fan(CPUA_INTAKE_FAN_RPM_INDEX, intake);
1038                 set_rpm_fan(CPUA_EXHAUST_FAN_RPM_INDEX, state->rpm);
1039         } else {
1040                 set_rpm_fan(CPUB_INTAKE_FAN_RPM_INDEX, intake);
1041                 set_rpm_fan(CPUB_EXHAUST_FAN_RPM_INDEX, state->rpm);
1042         }
1043 }
1044
1045 static void do_monitor_cpu_rack(struct cpu_pid_state *state)
1046 {
1047         s32 temp, power, fan_min;
1048         int rc;
1049
1050         /* Read current fan status */
1051         rc = do_read_one_cpu_values(state, &temp, &power);
1052         if (rc < 0) {
1053                 /* XXX What do we do now ? */
1054         }
1055
1056         /* Check tmax, increment overtemp if we are there. At tmax+8, we go
1057          * full blown immediately and try to trigger a shutdown
1058          */
1059         if (temp >= ((state->mpu.tmax + 8) << 16)) {
1060                 printk(KERN_WARNING "Warning ! CPU %d temperature way above maximum"
1061                        " (%d) !\n",
1062                        state->index, temp >> 16);
1063                 state->overtemp = CPU_MAX_OVERTEMP / 4;
1064         } else if (temp > (state->mpu.tmax << 16))
1065                 state->overtemp++;
1066         else
1067                 state->overtemp = 0;
1068         if (state->overtemp >= CPU_MAX_OVERTEMP)
1069                 critical_state = 1;
1070         if (state->overtemp > 0) {
1071                 state->rpm = state->intake_rpm = state->mpu.rmaxn_intake_fan;
1072                 goto do_set_fans;
1073         }
1074
1075         /* Do the PID */
1076         do_cpu_pid(state, temp, power);
1077
1078         /* Check clamp from dimms */
1079         fan_min = dimm_output_clamp;
1080         fan_min = max(fan_min, (int)state->mpu.rminn_intake_fan);
1081
1082         state->rpm = max(state->rpm, (int)fan_min);
1083         state->rpm = min(state->rpm, (int)state->mpu.rmaxn_intake_fan);
1084         state->intake_rpm = state->rpm;
1085
1086  do_set_fans:
1087         DBG("** CPU %d RPM: %d overtemp: %d\n",
1088             state->index, (int)state->rpm, state->overtemp);
1089
1090         /* We should check for errors, shouldn't we ? But then, what
1091          * do we do once the error occurs ? For FCU notified fan
1092          * failures (-EFAULT) we probably want to notify userland
1093          * some way...
1094          */
1095         if (state->index == 0) {
1096                 set_rpm_fan(CPU_A1_FAN_RPM_INDEX, state->rpm);
1097                 set_rpm_fan(CPU_A2_FAN_RPM_INDEX, state->rpm);
1098                 set_rpm_fan(CPU_A3_FAN_RPM_INDEX, state->rpm);
1099         } else {
1100                 set_rpm_fan(CPU_B1_FAN_RPM_INDEX, state->rpm);
1101                 set_rpm_fan(CPU_B2_FAN_RPM_INDEX, state->rpm);
1102                 set_rpm_fan(CPU_B3_FAN_RPM_INDEX, state->rpm);
1103         }
1104 }
1105
1106 /*
1107  * Initialize the state structure for one CPU control loop
1108  */
1109 static int init_cpu_state(struct cpu_pid_state *state, int index)
1110 {
1111         state->index = index;
1112         state->first = 1;
1113         state->rpm = (cpu_pid_type == CPU_PID_TYPE_RACKMAC) ? 4000 : 1000;
1114         state->overtemp = 0;
1115         state->adc_config = 0x00;
1116
1117
1118         if (index == 0)
1119                 state->monitor = attach_i2c_chip(SUPPLY_MONITOR_ID, "CPU0_monitor");
1120         else if (index == 1)
1121                 state->monitor = attach_i2c_chip(SUPPLY_MONITORB_ID, "CPU1_monitor");
1122         if (state->monitor == NULL)
1123                 goto fail;
1124
1125         if (read_eeprom(index, &state->mpu))
1126                 goto fail;
1127
1128         state->count_power = state->mpu.tguardband;
1129         if (state->count_power > CPU_POWER_HISTORY_SIZE) {
1130                 printk(KERN_WARNING "Warning ! too many power history slots\n");
1131                 state->count_power = CPU_POWER_HISTORY_SIZE;
1132         }
1133         DBG("CPU %d Using %d power history entries\n", index, state->count_power);
1134
1135         if (index == 0) {
1136                 device_create_file(&of_dev->dev, &dev_attr_cpu0_temperature);
1137                 device_create_file(&of_dev->dev, &dev_attr_cpu0_voltage);
1138                 device_create_file(&of_dev->dev, &dev_attr_cpu0_current);
1139                 device_create_file(&of_dev->dev, &dev_attr_cpu0_exhaust_fan_rpm);
1140                 device_create_file(&of_dev->dev, &dev_attr_cpu0_intake_fan_rpm);
1141         } else {
1142                 device_create_file(&of_dev->dev, &dev_attr_cpu1_temperature);
1143                 device_create_file(&of_dev->dev, &dev_attr_cpu1_voltage);
1144                 device_create_file(&of_dev->dev, &dev_attr_cpu1_current);
1145                 device_create_file(&of_dev->dev, &dev_attr_cpu1_exhaust_fan_rpm);
1146                 device_create_file(&of_dev->dev, &dev_attr_cpu1_intake_fan_rpm);
1147         }
1148
1149         return 0;
1150  fail:
1151         if (state->monitor)
1152                 detach_i2c_chip(state->monitor);
1153         state->monitor = NULL;
1154
1155         return -ENODEV;
1156 }
1157
1158 /*
1159  * Dispose of the state data for one CPU control loop
1160  */
1161 static void dispose_cpu_state(struct cpu_pid_state *state)
1162 {
1163         if (state->monitor == NULL)
1164                 return;
1165
1166         if (state->index == 0) {
1167                 device_remove_file(&of_dev->dev, &dev_attr_cpu0_temperature);
1168                 device_remove_file(&of_dev->dev, &dev_attr_cpu0_voltage);
1169                 device_remove_file(&of_dev->dev, &dev_attr_cpu0_current);
1170                 device_remove_file(&of_dev->dev, &dev_attr_cpu0_exhaust_fan_rpm);
1171                 device_remove_file(&of_dev->dev, &dev_attr_cpu0_intake_fan_rpm);
1172         } else {
1173                 device_remove_file(&of_dev->dev, &dev_attr_cpu1_temperature);
1174                 device_remove_file(&of_dev->dev, &dev_attr_cpu1_voltage);
1175                 device_remove_file(&of_dev->dev, &dev_attr_cpu1_current);
1176                 device_remove_file(&of_dev->dev, &dev_attr_cpu1_exhaust_fan_rpm);
1177                 device_remove_file(&of_dev->dev, &dev_attr_cpu1_intake_fan_rpm);
1178         }
1179
1180         detach_i2c_chip(state->monitor);
1181         state->monitor = NULL;
1182 }
1183
1184 /*
1185  * Motherboard backside & U3 heatsink fan control loop
1186  */
1187 static void do_monitor_backside(struct backside_pid_state *state)
1188 {
1189         s32 temp, integral, derivative, fan_min;
1190         s64 integ_p, deriv_p, prop_p, sum;
1191         int i, rc;
1192
1193         if (--state->ticks != 0)
1194                 return;
1195         state->ticks = backside_params.interval;
1196
1197         DBG("backside:\n");
1198
1199         /* Check fan status */
1200         rc = get_pwm_fan(BACKSIDE_FAN_PWM_INDEX);
1201         if (rc < 0) {
1202                 printk(KERN_WARNING "Error %d reading backside fan !\n", rc);
1203                 /* XXX What do we do now ? */
1204         } else
1205                 state->pwm = rc;
1206         DBG("  current pwm: %d\n", state->pwm);
1207
1208         /* Get some sensor readings */
1209         temp = i2c_smbus_read_byte_data(state->monitor, MAX6690_EXT_TEMP) << 16;
1210         state->last_temp = temp;
1211         DBG("  temp: %d.%03d, target: %d.%03d\n", FIX32TOPRINT(temp),
1212             FIX32TOPRINT(backside_params.input_target));
1213
1214         /* Store temperature and error in history array */
1215         state->cur_sample = (state->cur_sample + 1) % BACKSIDE_PID_HISTORY_SIZE;
1216         state->sample_history[state->cur_sample] = temp;
1217         state->error_history[state->cur_sample] = temp - backside_params.input_target;
1218
1219         /* If first loop, fill the history table */
1220         if (state->first) {
1221                 for (i = 0; i < (BACKSIDE_PID_HISTORY_SIZE - 1); i++) {
1222                         state->cur_sample = (state->cur_sample + 1) %
1223                                 BACKSIDE_PID_HISTORY_SIZE;
1224                         state->sample_history[state->cur_sample] = temp;
1225                         state->error_history[state->cur_sample] =
1226                                 temp - backside_params.input_target;
1227                 }
1228                 state->first = 0;
1229         }
1230
1231         /* Calculate the integral term */
1232         sum = 0;
1233         integral = 0;
1234         for (i = 0; i < BACKSIDE_PID_HISTORY_SIZE; i++)
1235                 integral += state->error_history[i];
1236         integral *= backside_params.interval;
1237         DBG("  integral: %08x\n", integral);
1238         integ_p = ((s64)backside_params.G_r) * (s64)integral;
1239         DBG("   integ_p: %d\n", (int)(integ_p >> 36));
1240         sum += integ_p;
1241
1242         /* Calculate the derivative term */
1243         derivative = state->error_history[state->cur_sample] -
1244                 state->error_history[(state->cur_sample + BACKSIDE_PID_HISTORY_SIZE - 1)
1245                                     % BACKSIDE_PID_HISTORY_SIZE];
1246         derivative /= backside_params.interval;
1247         deriv_p = ((s64)backside_params.G_d) * (s64)derivative;
1248         DBG("   deriv_p: %d\n", (int)(deriv_p >> 36));
1249         sum += deriv_p;
1250
1251         /* Calculate the proportional term */
1252         prop_p = ((s64)backside_params.G_p) * (s64)(state->error_history[state->cur_sample]);
1253         DBG("   prop_p: %d\n", (int)(prop_p >> 36));
1254         sum += prop_p;
1255
1256         /* Scale sum */
1257         sum >>= 36;
1258
1259         DBG("   sum: %d\n", (int)sum);
1260         if (backside_params.additive)
1261                 state->pwm += (s32)sum;
1262         else
1263                 state->pwm = sum;
1264
1265         /* Check for clamp */
1266         fan_min = (dimm_output_clamp * 100) / 14000;
1267         fan_min = max(fan_min, backside_params.output_min);
1268
1269         state->pwm = max(state->pwm, fan_min);
1270         state->pwm = min(state->pwm, backside_params.output_max);
1271
1272         DBG("** BACKSIDE PWM: %d\n", (int)state->pwm);
1273         set_pwm_fan(BACKSIDE_FAN_PWM_INDEX, state->pwm);
1274 }
1275
1276 /*
1277  * Initialize the state structure for the backside fan control loop
1278  */
1279 static int init_backside_state(struct backside_pid_state *state)
1280 {
1281         struct device_node *u3;
1282         int u3h = 1; /* conservative by default */
1283
1284         /*
1285          * There are different PID params for machines with U3 and machines
1286          * with U3H, pick the right ones now
1287          */
1288         u3 = of_find_node_by_path("/u3@0,f8000000");
1289         if (u3 != NULL) {
1290                 u32 *vers = (u32 *)get_property(u3, "device-rev", NULL);
1291                 if (vers)
1292                         if (((*vers) & 0x3f) < 0x34)
1293                                 u3h = 0;
1294                 of_node_put(u3);
1295         }
1296
1297         if (rackmac) {
1298                 backside_params.G_d = BACKSIDE_PID_RACK_G_d;
1299                 backside_params.input_target = BACKSIDE_PID_RACK_INPUT_TARGET;
1300                 backside_params.output_min = BACKSIDE_PID_U3H_OUTPUT_MIN;
1301                 backside_params.interval = BACKSIDE_PID_RACK_INTERVAL;
1302                 backside_params.G_p = BACKSIDE_PID_RACK_G_p;
1303                 backside_params.G_r = BACKSIDE_PID_G_r;
1304                 backside_params.output_max = BACKSIDE_PID_OUTPUT_MAX;
1305                 backside_params.additive = 0;
1306         } else if (u3h) {
1307                 backside_params.G_d = BACKSIDE_PID_U3H_G_d;
1308                 backside_params.input_target = BACKSIDE_PID_U3H_INPUT_TARGET;
1309                 backside_params.output_min = BACKSIDE_PID_U3H_OUTPUT_MIN;
1310                 backside_params.interval = BACKSIDE_PID_INTERVAL;
1311                 backside_params.G_p = BACKSIDE_PID_G_p;
1312                 backside_params.G_r = BACKSIDE_PID_G_r;
1313                 backside_params.output_max = BACKSIDE_PID_OUTPUT_MAX;
1314                 backside_params.additive = 1;
1315         } else {
1316                 backside_params.G_d = BACKSIDE_PID_U3_G_d;
1317                 backside_params.input_target = BACKSIDE_PID_U3_INPUT_TARGET;
1318                 backside_params.output_min = BACKSIDE_PID_U3_OUTPUT_MIN;
1319                 backside_params.interval = BACKSIDE_PID_INTERVAL;
1320                 backside_params.G_p = BACKSIDE_PID_G_p;
1321                 backside_params.G_r = BACKSIDE_PID_G_r;
1322                 backside_params.output_max = BACKSIDE_PID_OUTPUT_MAX;
1323                 backside_params.additive = 1;
1324         }
1325
1326         state->ticks = 1;
1327         state->first = 1;
1328         state->pwm = 50;
1329
1330         state->monitor = attach_i2c_chip(BACKSIDE_MAX_ID, "backside_temp");
1331         if (state->monitor == NULL)
1332                 return -ENODEV;
1333
1334         device_create_file(&of_dev->dev, &dev_attr_backside_temperature);
1335         device_create_file(&of_dev->dev, &dev_attr_backside_fan_pwm);
1336
1337         return 0;
1338 }
1339
1340 /*
1341  * Dispose of the state data for the backside control loop
1342  */
1343 static void dispose_backside_state(struct backside_pid_state *state)
1344 {
1345         if (state->monitor == NULL)
1346                 return;
1347
1348         device_remove_file(&of_dev->dev, &dev_attr_backside_temperature);
1349         device_remove_file(&of_dev->dev, &dev_attr_backside_fan_pwm);
1350
1351         detach_i2c_chip(state->monitor);
1352         state->monitor = NULL;
1353 }
1354
1355 /*
1356  * Drives bay fan control loop
1357  */
1358 static void do_monitor_drives(struct drives_pid_state *state)
1359 {
1360         s32 temp, integral, derivative;
1361         s64 integ_p, deriv_p, prop_p, sum;
1362         int i, rc;
1363
1364         if (--state->ticks != 0)
1365                 return;
1366         state->ticks = DRIVES_PID_INTERVAL;
1367
1368         DBG("drives:\n");
1369
1370         /* Check fan status */
1371         rc = get_rpm_fan(DRIVES_FAN_RPM_INDEX, !RPM_PID_USE_ACTUAL_SPEED);
1372         if (rc < 0) {
1373                 printk(KERN_WARNING "Error %d reading drives fan !\n", rc);
1374                 /* XXX What do we do now ? */
1375         } else
1376                 state->rpm = rc;
1377         DBG("  current rpm: %d\n", state->rpm);
1378
1379         /* Get some sensor readings */
1380         temp = le16_to_cpu(i2c_smbus_read_word_data(state->monitor, DS1775_TEMP)) << 8;
1381         state->last_temp = temp;
1382         DBG("  temp: %d.%03d, target: %d.%03d\n", FIX32TOPRINT(temp),
1383             FIX32TOPRINT(DRIVES_PID_INPUT_TARGET));
1384
1385         /* Store temperature and error in history array */
1386         state->cur_sample = (state->cur_sample + 1) % DRIVES_PID_HISTORY_SIZE;
1387         state->sample_history[state->cur_sample] = temp;
1388         state->error_history[state->cur_sample] = temp - DRIVES_PID_INPUT_TARGET;
1389
1390         /* If first loop, fill the history table */
1391         if (state->first) {
1392                 for (i = 0; i < (DRIVES_PID_HISTORY_SIZE - 1); i++) {
1393                         state->cur_sample = (state->cur_sample + 1) %
1394                                 DRIVES_PID_HISTORY_SIZE;
1395                         state->sample_history[state->cur_sample] = temp;
1396                         state->error_history[state->cur_sample] =
1397                                 temp - DRIVES_PID_INPUT_TARGET;
1398                 }
1399                 state->first = 0;
1400         }
1401
1402         /* Calculate the integral term */
1403         sum = 0;
1404         integral = 0;
1405         for (i = 0; i < DRIVES_PID_HISTORY_SIZE; i++)
1406                 integral += state->error_history[i];
1407         integral *= DRIVES_PID_INTERVAL;
1408         DBG("  integral: %08x\n", integral);
1409         integ_p = ((s64)DRIVES_PID_G_r) * (s64)integral;
1410         DBG("   integ_p: %d\n", (int)(integ_p >> 36));
1411         sum += integ_p;
1412
1413         /* Calculate the derivative term */
1414         derivative = state->error_history[state->cur_sample] -
1415                 state->error_history[(state->cur_sample + DRIVES_PID_HISTORY_SIZE - 1)
1416                                     % DRIVES_PID_HISTORY_SIZE];
1417         derivative /= DRIVES_PID_INTERVAL;
1418         deriv_p = ((s64)DRIVES_PID_G_d) * (s64)derivative;
1419         DBG("   deriv_p: %d\n", (int)(deriv_p >> 36));
1420         sum += deriv_p;
1421
1422         /* Calculate the proportional term */
1423         prop_p = ((s64)DRIVES_PID_G_p) * (s64)(state->error_history[state->cur_sample]);
1424         DBG("   prop_p: %d\n", (int)(prop_p >> 36));
1425         sum += prop_p;
1426
1427         /* Scale sum */
1428         sum >>= 36;
1429
1430         DBG("   sum: %d\n", (int)sum);
1431         state->rpm += (s32)sum;
1432
1433         state->rpm = max(state->rpm, DRIVES_PID_OUTPUT_MIN);
1434         state->rpm = min(state->rpm, DRIVES_PID_OUTPUT_MAX);
1435
1436         DBG("** DRIVES RPM: %d\n", (int)state->rpm);
1437         set_rpm_fan(DRIVES_FAN_RPM_INDEX, state->rpm);
1438 }
1439
1440 /*
1441  * Initialize the state structure for the drives bay fan control loop
1442  */
1443 static int init_drives_state(struct drives_pid_state *state)
1444 {
1445         state->ticks = 1;
1446         state->first = 1;
1447         state->rpm = 1000;
1448
1449         state->monitor = attach_i2c_chip(DRIVES_DALLAS_ID, "drives_temp");
1450         if (state->monitor == NULL)
1451                 return -ENODEV;
1452
1453         device_create_file(&of_dev->dev, &dev_attr_drives_temperature);
1454         device_create_file(&of_dev->dev, &dev_attr_drives_fan_rpm);
1455
1456         return 0;
1457 }
1458
1459 /*
1460  * Dispose of the state data for the drives control loop
1461  */
1462 static void dispose_drives_state(struct drives_pid_state *state)
1463 {
1464         if (state->monitor == NULL)
1465                 return;
1466
1467         device_remove_file(&of_dev->dev, &dev_attr_drives_temperature);
1468         device_remove_file(&of_dev->dev, &dev_attr_drives_fan_rpm);
1469
1470         detach_i2c_chip(state->monitor);
1471         state->monitor = NULL;
1472 }
1473
1474 /*
1475  * DIMMs temp control loop
1476  */
1477 static void do_monitor_dimms(struct dimm_pid_state *state)
1478 {
1479         s32 temp, integral, derivative, fan_min;
1480         s64 integ_p, deriv_p, prop_p, sum;
1481         int i;
1482
1483         if (--state->ticks != 0)
1484                 return;
1485         state->ticks = DIMM_PID_INTERVAL;
1486
1487         DBG("DIMM:\n");
1488
1489         DBG("  current value: %d\n", state->output);
1490
1491         temp = read_lm87_reg(state->monitor, LM87_INT_TEMP);
1492         if (temp < 0)
1493                 return;
1494         temp <<= 16;
1495         state->last_temp = temp;
1496         DBG("  temp: %d.%03d, target: %d.%03d\n", FIX32TOPRINT(temp),
1497             FIX32TOPRINT(DIMM_PID_INPUT_TARGET));
1498
1499         /* Store temperature and error in history array */
1500         state->cur_sample = (state->cur_sample + 1) % DIMM_PID_HISTORY_SIZE;
1501         state->sample_history[state->cur_sample] = temp;
1502         state->error_history[state->cur_sample] = temp - DIMM_PID_INPUT_TARGET;
1503
1504         /* If first loop, fill the history table */
1505         if (state->first) {
1506                 for (i = 0; i < (DIMM_PID_HISTORY_SIZE - 1); i++) {
1507                         state->cur_sample = (state->cur_sample + 1) %
1508                                 DIMM_PID_HISTORY_SIZE;
1509                         state->sample_history[state->cur_sample] = temp;
1510                         state->error_history[state->cur_sample] =
1511                                 temp - DIMM_PID_INPUT_TARGET;
1512                 }
1513                 state->first = 0;
1514         }
1515
1516         /* Calculate the integral term */
1517         sum = 0;
1518         integral = 0;
1519         for (i = 0; i < DIMM_PID_HISTORY_SIZE; i++)
1520                 integral += state->error_history[i];
1521         integral *= DIMM_PID_INTERVAL;
1522         DBG("  integral: %08x\n", integral);
1523         integ_p = ((s64)DIMM_PID_G_r) * (s64)integral;
1524         DBG("   integ_p: %d\n", (int)(integ_p >> 36));
1525         sum += integ_p;
1526
1527         /* Calculate the derivative term */
1528         derivative = state->error_history[state->cur_sample] -
1529                 state->error_history[(state->cur_sample + DIMM_PID_HISTORY_SIZE - 1)
1530                                     % DIMM_PID_HISTORY_SIZE];
1531         derivative /= DIMM_PID_INTERVAL;
1532         deriv_p = ((s64)DIMM_PID_G_d) * (s64)derivative;
1533         DBG("   deriv_p: %d\n", (int)(deriv_p >> 36));
1534         sum += deriv_p;
1535
1536         /* Calculate the proportional term */
1537         prop_p = ((s64)DIMM_PID_G_p) * (s64)(state->error_history[state->cur_sample]);
1538         DBG("   prop_p: %d\n", (int)(prop_p >> 36));
1539         sum += prop_p;
1540
1541         /* Scale sum */
1542         sum >>= 36;
1543
1544         DBG("   sum: %d\n", (int)sum);
1545         state->output = (s32)sum;
1546         state->output = max(state->output, DIMM_PID_OUTPUT_MIN);
1547         state->output = min(state->output, DIMM_PID_OUTPUT_MAX);
1548         dimm_output_clamp = state->output;
1549
1550         DBG("** DIMM clamp value: %d\n", (int)state->output);
1551
1552         /* Backside PID is only every 5 seconds, force backside fan clamping now */
1553         fan_min = (dimm_output_clamp * 100) / 14000;
1554         fan_min = max(fan_min, backside_params.output_min);
1555         if (backside_state.pwm < fan_min) {
1556                 backside_state.pwm = fan_min;
1557                 DBG(" -> applying clamp to backside fan now: %d  !\n", fan_min);
1558                 set_pwm_fan(BACKSIDE_FAN_PWM_INDEX, fan_min);
1559         }
1560 }
1561
1562 /*
1563  * Initialize the state structure for the DIMM temp control loop
1564  */
1565 static int init_dimms_state(struct dimm_pid_state *state)
1566 {
1567         state->ticks = 1;
1568         state->first = 1;
1569         state->output = 4000;
1570
1571         state->monitor = attach_i2c_chip(XSERVE_DIMMS_LM87, "dimms_temp");
1572         if (state->monitor == NULL)
1573                 return -ENODEV;
1574
1575         device_create_file(&of_dev->dev, &dev_attr_dimms_temperature);
1576
1577         return 0;
1578 }
1579
1580 /*
1581  * Dispose of the state data for the drives control loop
1582  */
1583 static void dispose_dimms_state(struct dimm_pid_state *state)
1584 {
1585         if (state->monitor == NULL)
1586                 return;
1587
1588         device_remove_file(&of_dev->dev, &dev_attr_dimms_temperature);
1589
1590         detach_i2c_chip(state->monitor);
1591         state->monitor = NULL;
1592 }
1593
1594 static int call_critical_overtemp(void)
1595 {
1596         char *argv[] = { critical_overtemp_path, NULL };
1597         static char *envp[] = { "HOME=/",
1598                                 "TERM=linux",
1599                                 "PATH=/sbin:/usr/sbin:/bin:/usr/bin",
1600                                 NULL };
1601
1602         return call_usermodehelper(critical_overtemp_path, argv, envp, 0);
1603 }
1604
1605
1606 /*
1607  * Here's the kernel thread that calls the various control loops
1608  */
1609 static int main_control_loop(void *x)
1610 {
1611         daemonize("kfand");
1612
1613         DBG("main_control_loop started\n");
1614
1615         down(&driver_lock);
1616
1617         if (start_fcu() < 0) {
1618                 printk(KERN_ERR "kfand: failed to start FCU\n");
1619                 up(&driver_lock);
1620                 goto out;
1621         }
1622
1623         /* Set the PCI fan once for now */
1624         set_pwm_fan(SLOTS_FAN_PWM_INDEX, SLOTS_FAN_DEFAULT_PWM);
1625
1626         /* Initialize ADCs */
1627         initialize_adc(&cpu_state[0]);
1628         if (cpu_state[1].monitor != NULL)
1629                 initialize_adc(&cpu_state[1]);
1630
1631         up(&driver_lock);
1632
1633         while (state == state_attached) {
1634                 unsigned long elapsed, start;
1635
1636                 start = jiffies;
1637
1638                 down(&driver_lock);
1639
1640                 /* First, we always calculate the new DIMMs state on an Xserve */
1641                 if (rackmac)
1642                         do_monitor_dimms(&dimms_state);
1643
1644                 /* Then, the CPUs */
1645                 if (cpu_pid_type == CPU_PID_TYPE_COMBINED)
1646                         do_monitor_cpu_combined();
1647                 else if (cpu_pid_type == CPU_PID_TYPE_RACKMAC) {
1648                         do_monitor_cpu_rack(&cpu_state[0]);
1649                         if (cpu_state[1].monitor != NULL)
1650                                 do_monitor_cpu_rack(&cpu_state[1]);
1651                         // better deal with UP
1652                 } else {
1653                         do_monitor_cpu_split(&cpu_state[0]);
1654                         if (cpu_state[1].monitor != NULL)
1655                                 do_monitor_cpu_split(&cpu_state[1]);
1656                         // better deal with UP
1657                 }
1658                 /* Then, the rest */
1659                 do_monitor_backside(&backside_state);
1660                 if (!rackmac)
1661                         do_monitor_drives(&drives_state);
1662                 up(&driver_lock);
1663
1664                 if (critical_state == 1) {
1665                         printk(KERN_WARNING "Temperature control detected a critical condition\n");
1666                         printk(KERN_WARNING "Attempting to shut down...\n");
1667                         if (call_critical_overtemp()) {
1668                                 printk(KERN_WARNING "Can't call %s, power off now!\n",
1669                                        critical_overtemp_path);
1670                                 machine_power_off();
1671                         }
1672                 }
1673                 if (critical_state > 0)
1674                         critical_state++;
1675                 if (critical_state > MAX_CRITICAL_STATE) {
1676                         printk(KERN_WARNING "Shutdown timed out, power off now !\n");
1677                         machine_power_off();
1678                 }
1679
1680                 // FIXME: Deal with signals
1681                 elapsed = jiffies - start;
1682                 if (elapsed < HZ)
1683                         schedule_timeout_interruptible(HZ - elapsed);
1684         }
1685
1686  out:
1687         DBG("main_control_loop ended\n");
1688
1689         ctrl_task = 0;
1690         complete_and_exit(&ctrl_complete, 0);
1691 }
1692
1693 /*
1694  * Dispose the control loops when tearing down
1695  */
1696 static void dispose_control_loops(void)
1697 {
1698         dispose_cpu_state(&cpu_state[0]);
1699         dispose_cpu_state(&cpu_state[1]);
1700         dispose_backside_state(&backside_state);
1701         dispose_drives_state(&drives_state);
1702         dispose_dimms_state(&dimms_state);
1703 }
1704
1705 /*
1706  * Create the control loops. U3-0 i2c bus is up, so we can now
1707  * get to the various sensors
1708  */
1709 static int create_control_loops(void)
1710 {
1711         struct device_node *np;
1712
1713         /* Count CPUs from the device-tree, we don't care how many are
1714          * actually used by Linux
1715          */
1716         cpu_count = 0;
1717         for (np = NULL; NULL != (np = of_find_node_by_type(np, "cpu"));)
1718                 cpu_count++;
1719
1720         DBG("counted %d CPUs in the device-tree\n", cpu_count);
1721
1722         /* Decide the type of PID algorithm to use based on the presence of
1723          * the pumps, though that may not be the best way, that is good enough
1724          * for now
1725          */
1726         if (rackmac)
1727                 cpu_pid_type = CPU_PID_TYPE_RACKMAC;
1728         else if (machine_is_compatible("PowerMac7,3")
1729             && (cpu_count > 1)
1730             && fcu_fans[CPUA_PUMP_RPM_INDEX].id != FCU_FAN_ABSENT_ID
1731             && fcu_fans[CPUB_PUMP_RPM_INDEX].id != FCU_FAN_ABSENT_ID) {
1732                 printk(KERN_INFO "Liquid cooling pumps detected, using new algorithm !\n");
1733                 cpu_pid_type = CPU_PID_TYPE_COMBINED;
1734         } else
1735                 cpu_pid_type = CPU_PID_TYPE_SPLIT;
1736
1737         /* Create control loops for everything. If any fail, everything
1738          * fails
1739          */
1740         if (init_cpu_state(&cpu_state[0], 0))
1741                 goto fail;
1742         if (cpu_pid_type == CPU_PID_TYPE_COMBINED)
1743                 fetch_cpu_pumps_minmax();
1744
1745         if (cpu_count > 1 && init_cpu_state(&cpu_state[1], 1))
1746                 goto fail;
1747         if (init_backside_state(&backside_state))
1748                 goto fail;
1749         if (rackmac && init_dimms_state(&dimms_state))
1750                 goto fail;
1751         if (!rackmac && init_drives_state(&drives_state))
1752                 goto fail;
1753
1754         DBG("all control loops up !\n");
1755
1756         return 0;
1757
1758  fail:
1759         DBG("failure creating control loops, disposing\n");
1760
1761         dispose_control_loops();
1762
1763         return -ENODEV;
1764 }
1765
1766 /*
1767  * Start the control loops after everything is up, that is create
1768  * the thread that will make them run
1769  */
1770 static void start_control_loops(void)
1771 {
1772         init_completion(&ctrl_complete);
1773
1774         ctrl_task = kernel_thread(main_control_loop, NULL, SIGCHLD | CLONE_KERNEL);
1775 }
1776
1777 /*
1778  * Stop the control loops when tearing down
1779  */
1780 static void stop_control_loops(void)
1781 {
1782         if (ctrl_task != 0)
1783                 wait_for_completion(&ctrl_complete);
1784 }
1785
1786 /*
1787  * Attach to the i2c FCU after detecting U3-1 bus
1788  */
1789 static int attach_fcu(void)
1790 {
1791         fcu = attach_i2c_chip(FAN_CTRLER_ID, "fcu");
1792         if (fcu == NULL)
1793                 return -ENODEV;
1794
1795         DBG("FCU attached\n");
1796
1797         return 0;
1798 }
1799
1800 /*
1801  * Detach from the i2c FCU when tearing down
1802  */
1803 static void detach_fcu(void)
1804 {
1805         if (fcu)
1806                 detach_i2c_chip(fcu);
1807         fcu = NULL;
1808 }
1809
1810 /*
1811  * Attach to the i2c controller. We probe the various chips based
1812  * on the device-tree nodes and build everything for the driver to
1813  * run, we then kick the driver monitoring thread
1814  */
1815 static int therm_pm72_attach(struct i2c_adapter *adapter)
1816 {
1817         down(&driver_lock);
1818
1819         /* Check state */
1820         if (state == state_detached)
1821                 state = state_attaching;
1822         if (state != state_attaching) {
1823                 up(&driver_lock);
1824                 return 0;
1825         }
1826
1827         /* Check if we are looking for one of these */
1828         if (u3_0 == NULL && !strcmp(adapter->name, "u3 0")) {
1829                 u3_0 = adapter;
1830                 DBG("found U3-0\n");
1831                 if (k2 || !rackmac)
1832                         if (create_control_loops())
1833                                 u3_0 = NULL;
1834         } else if (u3_1 == NULL && !strcmp(adapter->name, "u3 1")) {
1835                 u3_1 = adapter;
1836                 DBG("found U3-1, attaching FCU\n");
1837                 if (attach_fcu())
1838                         u3_1 = NULL;
1839         } else if (k2 == NULL && !strcmp(adapter->name, "mac-io 0")) {
1840                 k2 = adapter;
1841                 DBG("Found K2\n");
1842                 if (u3_0 && rackmac)
1843                         if (create_control_loops())
1844                                 k2 = NULL;
1845         }
1846         /* We got all we need, start control loops */
1847         if (u3_0 != NULL && u3_1 != NULL && (k2 || !rackmac)) {
1848                 DBG("everything up, starting control loops\n");
1849                 state = state_attached;
1850                 start_control_loops();
1851         }
1852         up(&driver_lock);
1853
1854         return 0;
1855 }
1856
1857 /*
1858  * Called on every adapter when the driver or the i2c controller
1859  * is going away.
1860  */
1861 static int therm_pm72_detach(struct i2c_adapter *adapter)
1862 {
1863         down(&driver_lock);
1864
1865         if (state != state_detached)
1866                 state = state_detaching;
1867
1868         /* Stop control loops if any */
1869         DBG("stopping control loops\n");
1870         up(&driver_lock);
1871         stop_control_loops();
1872         down(&driver_lock);
1873
1874         if (u3_0 != NULL && !strcmp(adapter->name, "u3 0")) {
1875                 DBG("lost U3-0, disposing control loops\n");
1876                 dispose_control_loops();
1877                 u3_0 = NULL;
1878         }
1879
1880         if (u3_1 != NULL && !strcmp(adapter->name, "u3 1")) {
1881                 DBG("lost U3-1, detaching FCU\n");
1882                 detach_fcu();
1883                 u3_1 = NULL;
1884         }
1885         if (u3_0 == NULL && u3_1 == NULL)
1886                 state = state_detached;
1887
1888         up(&driver_lock);
1889
1890         return 0;
1891 }
1892
1893 static int fan_check_loc_match(const char *loc, int fan)
1894 {
1895         char    tmp[64];
1896         char    *c, *e;
1897
1898         strlcpy(tmp, fcu_fans[fan].loc, 64);
1899
1900         c = tmp;
1901         for (;;) {
1902                 e = strchr(c, ',');
1903                 if (e)
1904                         *e = 0;
1905                 if (strcmp(loc, c) == 0)
1906                         return 1;
1907                 if (e == NULL)
1908                         break;
1909                 c = e + 1;
1910         }
1911         return 0;
1912 }
1913
1914 static void fcu_lookup_fans(struct device_node *fcu_node)
1915 {
1916         struct device_node *np = NULL;
1917         int i;
1918
1919         /* The table is filled by default with values that are suitable
1920          * for the old machines without device-tree informations. We scan
1921          * the device-tree and override those values with whatever is
1922          * there
1923          */
1924
1925         DBG("Looking up FCU controls in device-tree...\n");
1926
1927         while ((np = of_get_next_child(fcu_node, np)) != NULL) {
1928                 int type = -1;
1929                 char *loc;
1930                 u32 *reg;
1931
1932                 DBG(" control: %s, type: %s\n", np->name, np->type);
1933
1934                 /* Detect control type */
1935                 if (!strcmp(np->type, "fan-rpm-control") ||
1936                     !strcmp(np->type, "fan-rpm"))
1937                         type = FCU_FAN_RPM;
1938                 if (!strcmp(np->type, "fan-pwm-control") ||
1939                     !strcmp(np->type, "fan-pwm"))
1940                         type = FCU_FAN_PWM;
1941                 /* Only care about fans for now */
1942                 if (type == -1)
1943                         continue;
1944
1945                 /* Lookup for a matching location */
1946                 loc = (char *)get_property(np, "location", NULL);
1947                 reg = (u32 *)get_property(np, "reg", NULL);
1948                 if (loc == NULL || reg == NULL)
1949                         continue;
1950                 DBG(" matching location: %s, reg: 0x%08x\n", loc, *reg);
1951
1952                 for (i = 0; i < FCU_FAN_COUNT; i++) {
1953                         int fan_id;
1954
1955                         if (!fan_check_loc_match(loc, i))
1956                                 continue;
1957                         DBG(" location match, index: %d\n", i);
1958                         fcu_fans[i].id = FCU_FAN_ABSENT_ID;
1959                         if (type != fcu_fans[i].type) {
1960                                 printk(KERN_WARNING "therm_pm72: Fan type mismatch "
1961                                        "in device-tree for %s\n", np->full_name);
1962                                 break;
1963                         }
1964                         if (type == FCU_FAN_RPM)
1965                                 fan_id = ((*reg) - 0x10) / 2;
1966                         else
1967                                 fan_id = ((*reg) - 0x30) / 2;
1968                         if (fan_id > 7) {
1969                                 printk(KERN_WARNING "therm_pm72: Can't parse "
1970                                        "fan ID in device-tree for %s\n", np->full_name);
1971                                 break;
1972                         }
1973                         DBG(" fan id -> %d, type -> %d\n", fan_id, type);
1974                         fcu_fans[i].id = fan_id;
1975                 }
1976         }
1977
1978         /* Now dump the array */
1979         printk(KERN_INFO "Detected fan controls:\n");
1980         for (i = 0; i < FCU_FAN_COUNT; i++) {
1981                 if (fcu_fans[i].id == FCU_FAN_ABSENT_ID)
1982                         continue;
1983                 printk(KERN_INFO "  %d: %s fan, id %d, location: %s\n", i,
1984                        fcu_fans[i].type == FCU_FAN_RPM ? "RPM" : "PWM",
1985                        fcu_fans[i].id, fcu_fans[i].loc);
1986         }
1987 }
1988
1989 static int fcu_of_probe(struct of_device* dev, const struct of_device_id *match)
1990 {
1991         state = state_detached;
1992
1993         /* Lookup the fans in the device tree */
1994         fcu_lookup_fans(dev->node);
1995
1996         /* Add the driver */
1997         return i2c_add_driver(&therm_pm72_driver);
1998 }
1999
2000 static int fcu_of_remove(struct of_device* dev)
2001 {
2002         i2c_del_driver(&therm_pm72_driver);
2003
2004         return 0;
2005 }
2006
2007 static struct of_device_id fcu_match[] =
2008 {
2009         {
2010         .type           = "fcu",
2011         },
2012         {},
2013 };
2014
2015 static struct of_platform_driver fcu_of_platform_driver =
2016 {
2017         .name           = "temperature",
2018         .match_table    = fcu_match,
2019         .probe          = fcu_of_probe,
2020         .remove         = fcu_of_remove
2021 };
2022
2023 /*
2024  * Check machine type, attach to i2c controller
2025  */
2026 static int __init therm_pm72_init(void)
2027 {
2028         struct device_node *np;
2029
2030         rackmac = machine_is_compatible("RackMac3,1");
2031
2032         if (!machine_is_compatible("PowerMac7,2") &&
2033             !machine_is_compatible("PowerMac7,3") &&
2034             !rackmac)
2035                 return -ENODEV;
2036
2037         printk(KERN_INFO "PowerMac G5 Thermal control driver %s\n", VERSION);
2038
2039         np = of_find_node_by_type(NULL, "fcu");
2040         if (np == NULL) {
2041                 /* Some machines have strangely broken device-tree */
2042                 np = of_find_node_by_path("/u3@0,f8000000/i2c@f8001000/fan@15e");
2043                 if (np == NULL) {
2044                             printk(KERN_ERR "Can't find FCU in device-tree !\n");
2045                             return -ENODEV;
2046                 }
2047         }
2048         of_dev = of_platform_device_create(np, "temperature", NULL);
2049         if (of_dev == NULL) {
2050                 printk(KERN_ERR "Can't register FCU platform device !\n");
2051                 return -ENODEV;
2052         }
2053
2054         of_register_driver(&fcu_of_platform_driver);
2055
2056         return 0;
2057 }
2058
2059 static void __exit therm_pm72_exit(void)
2060 {
2061         of_unregister_driver(&fcu_of_platform_driver);
2062
2063         if (of_dev)
2064                 of_device_unregister(of_dev);
2065 }
2066
2067 module_init(therm_pm72_init);
2068 module_exit(therm_pm72_exit);
2069
2070 MODULE_AUTHOR("Benjamin Herrenschmidt <benh@kernel.crashing.org>");
2071 MODULE_DESCRIPTION("Driver for Apple's PowerMac G5 thermal control");
2072 MODULE_LICENSE("GPL");
2073