Merge branch 'linus' into x86/cpu

[linux-2.6] / drivers / net / wireless / Kconfig

#
# Wireless LAN device configuration
#

menu "Wireless LAN"
        depends on !S390

config WLAN_PRE80211
        bool "Wireless LAN (pre-802.11)"
        depends on NETDEVICES
        ---help---
          Say Y if you have any pre-802.11 wireless LAN hardware.

          This option does not affect the kernel build, it only
          lets you choose drivers.

config STRIP
        tristate "STRIP (Metricom starmode radio IP)"
        depends on INET && WLAN_PRE80211
        select WIRELESS_EXT
        ---help---
          Say Y if you have a Metricom radio and intend to use Starmode Radio
          IP. STRIP is a radio protocol developed for the MosquitoNet project
          (on the WWW at <http://mosquitonet.stanford.edu/>) to send Internet
          traffic using Metricom radios.  Metricom radios are small, battery
          powered, 100kbit/sec packet radio transceivers, about the size and
          weight of a cellular telephone. (You may also have heard them called
          "Metricom modems" but we avoid the term "modem" because it misleads
          many people into thinking that you can plug a Metricom modem into a
          phone line and use it as a modem.)

          You can use STRIP on any Linux machine with a serial port, although
          it is obviously most useful for people with laptop computers. If you
          think you might get a Metricom radio in the future, there is no harm
          in saying Y to STRIP now, except that it makes the kernel a bit
          bigger.

          To compile this as a module, choose M here: the module will be
          called strip.

config ARLAN
        tristate "Aironet Arlan 655 & IC2200 DS support"
        depends on ISA && !64BIT && WLAN_PRE80211
        select WIRELESS_EXT
        ---help---
          Aironet makes Arlan, a class of wireless LAN adapters. These use the
          www.Telxon.com chip, which is also used on several similar cards.
          This driver is tested on the 655 and IC2200 series cards. Look at
          <http://www.ylenurme.ee/~elmer/655/> for the latest information.

          The driver is built as two modules, arlan and arlan-proc. The latter
          is the /proc interface and is not needed most of time.

          On some computers the card ends up in non-valid state after some
          time. Use a ping-reset script to clear it.

config WAVELAN
        tristate "AT&T/Lucent old WaveLAN & DEC RoamAbout DS ISA support"
        depends on ISA && WLAN_PRE80211
        select WIRELESS_EXT
        ---help---
          The Lucent WaveLAN (formerly NCR and AT&T; or DEC RoamAbout DS) is
          a Radio LAN (wireless Ethernet-like Local Area Network) using the
          radio frequencies 900 MHz and 2.4 GHz.

          If you want to use an ISA WaveLAN card under Linux, say Y and read
          the Ethernet-HOWTO, available from
          <http://www.tldp.org/docs.html#howto>. Some more specific
          information is contained in
          <file:Documentation/networking/wavelan.txt> and in the source code
          <file:drivers/net/wireless/wavelan.p.h>.

          You will also need the wireless tools package available from
          <http://www.hpl.hp.com/personal/Jean_Tourrilhes/Linux/Tools.html>.
          Please read the man pages contained therein.

          To compile this driver as a module, choose M here: the module will be
          called wavelan.

config PCMCIA_WAVELAN
        tristate "AT&T/Lucent old WaveLAN Pcmcia wireless support"
        depends on PCMCIA && WLAN_PRE80211
        select WIRELESS_EXT
        help
          Say Y here if you intend to attach an AT&T/Lucent Wavelan PCMCIA
          (PC-card) wireless Ethernet networking card to your computer.  This
          driver is for the non-IEEE-802.11 Wavelan cards.

          To compile this driver as a module, choose M here: the module will be
          called wavelan_cs.  If unsure, say N.

config PCMCIA_NETWAVE
        tristate "Xircom Netwave AirSurfer Pcmcia wireless support"
        depends on PCMCIA && WLAN_PRE80211
        select WIRELESS_EXT
        help
          Say Y here if you intend to attach this type of PCMCIA (PC-card)
          wireless Ethernet networking card to your computer.

          To compile this driver as a module, choose M here: the module will be
          called netwave_cs.  If unsure, say N.


config WLAN_80211
        bool "Wireless LAN (IEEE 802.11)"
        depends on NETDEVICES
        ---help---
          Say Y if you have any 802.11 wireless LAN hardware.

          This option does not affect the kernel build, it only
          lets you choose drivers.

config PCMCIA_RAYCS
        tristate "Aviator/Raytheon 2.4MHz wireless support"
        depends on PCMCIA && WLAN_80211
        select WIRELESS_EXT
        ---help---
          Say Y here if you intend to attach an Aviator/Raytheon PCMCIA
          (PC-card) wireless Ethernet networking card to your computer.
          Please read the file <file:Documentation/networking/ray_cs.txt> for
          details.

          To compile this driver as a module, choose M here: the module will be
          called ray_cs.  If unsure, say N.

config IPW2100
        tristate "Intel PRO/Wireless 2100 Network Connection"
        depends on PCI && WLAN_80211
        select WIRELESS_EXT
        select FW_LOADER
        select IEEE80211
        ---help---
          A driver for the Intel PRO/Wireless 2100 Network 
          Connection 802.11b wireless network adapter.

          See <file:Documentation/networking/README.ipw2100> for information on
          the capabilities currently enabled in this driver and for tips
          for debugging issues and problems.

          In order to use this driver, you will need a firmware image for it.
          You can obtain the firmware from
          <http://ipw2100.sf.net/>.  Once you have the firmware image, you 
          will need to place it in /lib/firmware.

          You will also very likely need the Wireless Tools in order to
          configure your card:

          <http://www.hpl.hp.com/personal/Jean_Tourrilhes/Linux/Tools.html>.

          It is recommended that you compile this driver as a module (M)
          rather than built-in (Y). This driver requires firmware at device
          initialization time, and when built-in this typically happens
          before the filesystem is accessible (hence firmware will be
          unavailable and initialization will fail). If you do choose to build
          this driver into your kernel image, you can avoid this problem by
          including the firmware and a firmware loader in an initramfs.
 
config IPW2100_MONITOR
        bool "Enable promiscuous mode"
        depends on IPW2100
        ---help---
          Enables promiscuous/monitor mode support for the ipw2100 driver.
          With this feature compiled into the driver, you can switch to 
          promiscuous mode via the Wireless Tool's Monitor mode.  While in this
          mode, no packets can be sent.

config IPW2100_DEBUG
        bool "Enable full debugging output in IPW2100 module."
        depends on IPW2100
        ---help---
          This option will enable debug tracing output for the IPW2100.  

          This will result in the kernel module being ~60k larger.  You can 
          control which debug output is sent to the kernel log by setting the 
          value in 

          /sys/bus/pci/drivers/ipw2100/debug_level

          This entry will only exist if this option is enabled.

          If you are not trying to debug or develop the IPW2100 driver, you 
          most likely want to say N here.

config IPW2200
        tristate "Intel PRO/Wireless 2200BG and 2915ABG Network Connection"
        depends on PCI && WLAN_80211
        select WIRELESS_EXT
        select FW_LOADER
        select IEEE80211
        ---help---
          A driver for the Intel PRO/Wireless 2200BG and 2915ABG Network
          Connection adapters. 

          See <file:Documentation/networking/README.ipw2200> for 
          information on the capabilities currently enabled in this 
          driver and for tips for debugging issues and problems.

          In order to use this driver, you will need a firmware image for it.
          You can obtain the firmware from
          <http://ipw2200.sf.net/>.  See the above referenced README.ipw2200 
          for information on where to install the firmware images.

          You will also very likely need the Wireless Tools in order to
          configure your card:

          <http://www.hpl.hp.com/personal/Jean_Tourrilhes/Linux/Tools.html>.

          It is recommended that you compile this driver as a module (M)
          rather than built-in (Y). This driver requires firmware at device
          initialization time, and when built-in this typically happens
          before the filesystem is accessible (hence firmware will be
          unavailable and initialization will fail). If you do choose to build
          this driver into your kernel image, you can avoid this problem by
          including the firmware and a firmware loader in an initramfs.

config IPW2200_MONITOR
        bool "Enable promiscuous mode"
        depends on IPW2200
        ---help---
          Enables promiscuous/monitor mode support for the ipw2200 driver.
          With this feature compiled into the driver, you can switch to 
          promiscuous mode via the Wireless Tool's Monitor mode.  While in this
          mode, no packets can be sent.

config IPW2200_RADIOTAP
        bool "Enable radiotap format 802.11 raw packet support"
        depends on IPW2200_MONITOR

config IPW2200_PROMISCUOUS
        bool "Enable creation of a RF radiotap promiscuous interface"
        depends on IPW2200_MONITOR
        select IPW2200_RADIOTAP
        ---help---
          Enables the creation of a second interface prefixed 'rtap'. 
          This second interface will provide every received in radiotap
          format.

          This is useful for performing wireless network analysis while
          maintaining an active association.

          Example usage:

            % modprobe ipw2200 rtap_iface=1
            % ifconfig rtap0 up
            % tethereal -i rtap0

          If you do not specify 'rtap_iface=1' as a module parameter then 
          the rtap interface will not be created and you will need to turn 
          it on via sysfs:
        
            % echo 1 > /sys/bus/pci/drivers/ipw2200/*/rtap_iface

config IPW2200_QOS
        bool "Enable QoS support"
        depends on IPW2200 && EXPERIMENTAL

config IPW2200_DEBUG
        bool "Enable full debugging output in IPW2200 module."
        depends on IPW2200
        ---help---
          This option will enable low level debug tracing output for IPW2200.

          Note, normal debug code is already compiled in. This low level
          debug option enables debug on hot paths (e.g Tx, Rx, ISR) and
          will result in the kernel module being ~70 larger.  Most users
          will typically not need this high verbosity debug information.

          If you are not sure, say N here.

config LIBERTAS
        tristate "Marvell 8xxx Libertas WLAN driver support"
        depends on WLAN_80211
        select WIRELESS_EXT
        select FW_LOADER
        ---help---
          A library for Marvell Libertas 8xxx devices.

config LIBERTAS_USB
        tristate "Marvell Libertas 8388 USB 802.11b/g cards"
        depends on LIBERTAS && USB
        ---help---
          A driver for Marvell Libertas 8388 USB devices.

config LIBERTAS_CS
        tristate "Marvell Libertas 8385 CompactFlash 802.11b/g cards"
        depends on LIBERTAS && PCMCIA
        select FW_LOADER
        ---help---
          A driver for Marvell Libertas 8385 CompactFlash devices.

config LIBERTAS_SDIO
        tristate "Marvell Libertas 8385 and 8686 SDIO 802.11b/g cards"
        depends on LIBERTAS && MMC
        ---help---
          A driver for Marvell Libertas 8385 and 8686 SDIO devices.

config LIBERTAS_DEBUG
        bool "Enable full debugging output in the Libertas module."
        depends on LIBERTAS
        ---help---
          Debugging support.

config AIRO
        tristate "Cisco/Aironet 34X/35X/4500/4800 ISA and PCI cards"
        depends on ISA_DMA_API && WLAN_80211 && (PCI || BROKEN)
        select WIRELESS_EXT
        select CRYPTO
        ---help---
          This is the standard Linux driver to support Cisco/Aironet ISA and
          PCI 802.11 wireless cards.
          It supports the new 802.11b cards from Cisco (Cisco 34X, Cisco 35X
          - with or without encryption) as well as card before the Cisco
          acquisition (Aironet 4500, Aironet 4800, Aironet 4800B).

          This driver support both the standard Linux Wireless Extensions
          and Cisco proprietary API, so both the Linux Wireless Tools and the
          Cisco Linux utilities can be used to configure the card.

          The driver can be compiled as a module and will be named "airo".

config HERMES
        tristate "Hermes chipset 802.11b support (Orinoco/Prism2/Symbol)"
        depends on (PPC_PMAC || PCI || PCMCIA) && WLAN_80211
        select WIRELESS_EXT
        ---help---
          A driver for 802.11b wireless cards based on the "Hermes" or
          Intersil HFA384x (Prism 2) MAC controller.  This includes the vast
          majority of the PCMCIA 802.11b cards (which are nearly all rebadges)
          - except for the Cisco/Aironet cards.  Cards supported include the
          Apple Airport (not a PCMCIA card), WavelanIEEE/Orinoco,
          Cabletron/EnteraSys Roamabout, ELSA AirLancer, MELCO Buffalo, Avaya,
          IBM High Rate Wireless, Farralon Syyline, Samsung MagicLAN, Netgear
          MA401, LinkSys WPC-11, D-Link DWL-650, 3Com AirConnect, Intel
          IPW2011, and Symbol Spectrum24 High Rate amongst others.

          This option includes the guts of the driver, but in order to
          actually use a card you will also need to enable support for PCMCIA
          Hermes cards, PLX9052 based PCI adaptors or the Apple Airport below.

          You will also very likely also need the Wireless Tools in order to
          configure your card and that /etc/pcmcia/wireless.opts works :
          <http://www.hpl.hp.com/personal/Jean_Tourrilhes/Linux/Tools.html>

config APPLE_AIRPORT
        tristate "Apple Airport support (built-in)"
        depends on PPC_PMAC && HERMES
        help
          Say Y here to support the Airport 802.11b wireless Ethernet hardware
          built into the Macintosh iBook and other recent PowerPC-based
          Macintosh machines. This is essentially a Lucent Orinoco card with 
          a non-standard interface.

          This driver does not support the Airport Extreme (802.11b/g). Use
          the BCM43xx driver for Airport Extreme cards.

config PLX_HERMES
        tristate "Hermes in PLX9052 based PCI adaptor support (Netgear MA301 etc.)"
        depends on PCI && HERMES
        help
          Enable support for PCMCIA cards supported by the "Hermes" (aka
          orinoco) driver when used in PLX9052 based PCI adaptors.  These
          adaptors are not a full PCMCIA controller but act as a more limited
          PCI <-> PCMCIA bridge.  Several vendors sell such adaptors so that
          802.11b PCMCIA cards can be used in desktop machines.  The Netgear
          MA301 is such an adaptor.

config TMD_HERMES
        tristate "Hermes in TMD7160 based PCI adaptor support"
        depends on PCI && HERMES
        help
          Enable support for PCMCIA cards supported by the "Hermes" (aka
          orinoco) driver when used in TMD7160 based PCI adaptors.  These
          adaptors are not a full PCMCIA controller but act as a more limited
          PCI <-> PCMCIA bridge.  Several vendors sell such adaptors so that
          802.11b PCMCIA cards can be used in desktop machines.

config NORTEL_HERMES
        tristate "Nortel emobility PCI adaptor support"
        depends on PCI && HERMES
        help
          Enable support for PCMCIA cards supported by the "Hermes" (aka
          orinoco) driver when used in Nortel emobility PCI adaptors.  These
          adaptors are not full PCMCIA controllers, but act as a more limited
          PCI <-> PCMCIA bridge.

config PCI_HERMES
        tristate "Prism 2.5 PCI 802.11b adaptor support"
        depends on PCI && HERMES
        help
          Enable support for PCI and mini-PCI 802.11b wireless NICs based on
          the Prism 2.5 chipset.  These are true PCI cards, not the 802.11b
          PCMCIA cards bundled with PCI<->PCMCIA adaptors which are also
          common.  Some of the built-in wireless adaptors in laptops are of
          this variety.

config PCMCIA_HERMES
        tristate "Hermes PCMCIA card support"
        depends on PCMCIA && HERMES
        ---help---
          A driver for "Hermes" chipset based PCMCIA wireless adaptors, such
          as the Lucent WavelanIEEE/Orinoco cards and their OEM (Cabletron/
          EnteraSys RoamAbout 802.11, ELSA Airlancer, Melco Buffalo and
          others).  It should also be usable on various Prism II based cards
          such as the Linksys, D-Link and Farallon Skyline.  It should also
          work on Symbol cards such as the 3Com AirConnect and Ericsson WLAN.

          You will very likely need the Wireless Tools in order to
          configure your card and that /etc/pcmcia/wireless.opts works:
          <http://www.hpl.hp.com/personal/Jean_Tourrilhes/Linux/Tools.html>.

config PCMCIA_SPECTRUM
        tristate "Symbol Spectrum24 Trilogy PCMCIA card support"
        depends on PCMCIA && HERMES
        select FW_LOADER
        ---help---

          This is a driver for 802.11b cards using RAM-loadable Symbol
          firmware, such as Symbol Wireless Networker LA4100, CompactFlash
          cards by Socket Communications and Intel PRO/Wireless 2011B.

          This driver requires firmware download on startup.  Utilities
          for downloading Symbol firmware are available at
          <http://sourceforge.net/projects/orinoco/>

config ATMEL
      tristate "Atmel at76c50x chipset  802.11b support"
      depends on (PCI || PCMCIA) && WLAN_80211
      select WIRELESS_EXT
      select FW_LOADER
      select CRC32
       ---help---
        A driver 802.11b wireless cards based on the Atmel fast-vnet
        chips. This driver supports standard Linux wireless extensions.

        Many  cards based on this chipset do not have flash memory
        and need their firmware loaded at start-up. If yours is
        one of these, you will need to provide a firmware image
        to be loaded into the card by the driver. The Atmel
        firmware package can be downloaded from
        <http://www.thekelleys.org.uk/atmel>

config PCI_ATMEL
      tristate "Atmel at76c506 PCI cards"
      depends on ATMEL && PCI
       ---help---
        Enable support for PCI and mini-PCI cards containing the
        Atmel at76c506 chip.

config PCMCIA_ATMEL
        tristate "Atmel at76c502/at76c504 PCMCIA cards"
        depends on ATMEL && PCMCIA
        select WIRELESS_EXT
        select FW_LOADER
        select CRC32
        ---help---
          Enable support for PCMCIA cards containing the
          Atmel at76c502 and at76c504 chips.

config AIRO_CS
        tristate "Cisco/Aironet 34X/35X/4500/4800 PCMCIA cards"
        depends on PCMCIA && (BROKEN || !M32R) && WLAN_80211
        select WIRELESS_EXT
        select CRYPTO
        select CRYPTO_AES
        ---help---
          This is the standard Linux driver to support Cisco/Aironet PCMCIA
          802.11 wireless cards.  This driver is the same as the Aironet
          driver part of the Linux Pcmcia package.
          It supports the new 802.11b cards from Cisco (Cisco 34X, Cisco 35X
          - with or without encryption) as well as card before the Cisco
          acquisition (Aironet 4500, Aironet 4800, Aironet 4800B). It also
          supports OEM of Cisco such as the DELL TrueMobile 4800 and Xircom
          802.11b cards.

          This driver support both the standard Linux Wireless Extensions
          and Cisco proprietary API, so both the Linux Wireless Tools and the
          Cisco Linux utilities can be used to configure the card.

config PCMCIA_WL3501
      tristate "Planet WL3501 PCMCIA cards"
      depends on EXPERIMENTAL && PCMCIA && WLAN_80211
      select WIRELESS_EXT
       ---help---
         A driver for WL3501 PCMCIA 802.11 wireless cards made by Planet.
         It has basic support for Linux wireless extensions and initial
         micro support for ethtool.

config PRISM54
        tristate 'Intersil Prism GT/Duette/Indigo PCI/Cardbus' 
        depends on PCI && EXPERIMENTAL && WLAN_80211
        select WIRELESS_EXT
        select FW_LOADER
        ---help---
          Enable PCI and Cardbus support for the following chipset based cards:

          ISL3880 - Prism GT            802.11 b/g
          ISL3877 - Prism Indigo        802.11 a
          ISL3890 - Prism Duette        802.11 a/b/g
          
          For a complete list of supported cards visit <http://prism54.org>.
          Here is the latest confirmed list of supported cards:

          3com OfficeConnect 11g Cardbus Card aka 3CRWE154G72 (version 1)
          Allnet ALL0271 PCI Card
          Compex WL54G Cardbus Card
          Corega CG-WLCB54GT Cardbus Card
          D-Link Air Plus Xtreme G A1 Cardbus Card aka DWL-g650
          I-O Data WN-G54/CB Cardbus Card
          Kobishi XG-300 aka Z-Com Cardbus Card
          Netgear WG511 Cardbus Card
          Ovislink WL-5400PCI PCI Card
          Peabird WLG-PCI PCI Card
          Sitecom WL-100i Cardbus Card
          Sitecom WL-110i PCI Card
          SMC2802W -    EZ Connect g 2.4GHz 54 Mbps Wireless PCI Card
          SMC2835W -    EZ Connect g 2.4GHz 54 Mbps Wireless Cardbus Card
          SMC2835W-V2 - EZ Connect g 2.4GHz 54 Mbps Wireless Cardbus Card
          Z-Com XG-900 PCI Card
          Zyxel G-100 Cardbus Card

          If you enable this you will need a firmware file as well.
          You will need to copy this to /usr/lib/hotplug/firmware/isl3890.
          You can get this non-GPL'd firmware file from the Prism54 project page:
          <http://prism54.org>
          You will also need the /etc/hotplug/firmware.agent script from
          a current hotplug package.

          Note: You need a motherboard with DMA support to use any of these cards 
          
          If you want to compile the driver as a module ( = code which can be
          inserted in and removed from the running kernel whenever you want),
          say M here and read <file:Documentation/kbuild/modules.txt>.
          The module will be called prism54.ko.

config USB_ZD1201
        tristate "USB ZD1201 based Wireless device support"
        depends on USB && WLAN_80211
        select WIRELESS_EXT
        select FW_LOADER
        ---help---
          Say Y if you want to use wireless LAN adapters based on the ZyDAS
          ZD1201 chip.

          This driver makes the adapter appear as a normal Ethernet interface,
          typically on wlan0.

          The zd1201 device requires external firmware to be loaded.
          This can be found at http://linux-lc100020.sourceforge.net/

          To compile this driver as a module, choose M here: the
          module will be called zd1201.

config USB_NET_RNDIS_WLAN
        tristate "Wireless RNDIS USB support"
        depends on USB && WLAN_80211 && EXPERIMENTAL
        select USB_USBNET
        select USB_NET_CDCETHER
        select USB_NET_RNDIS_HOST
        select WIRELESS_EXT
        ---help---
          This is a driver for wireless RNDIS devices.
          These are USB based adapters found in devices such as:

          Buffalo WLI-U2-KG125S
          U.S. Robotics USR5421
          Belkin F5D7051
          Linksys WUSB54GSv2
          Linksys WUSB54GSC
          Asus WL169gE
          Eminent EM4045
          BT Voyager 1055
          Linksys WUSB54GSv1
          U.S. Robotics USR5420
          BUFFALO WLI-USB-G54

          All of these devices are based on Broadcom 4320 chip which is the
          only wireless RNDIS chip known to date.

          If you choose to build a module, it'll be called rndis_wlan.

config RTL8180
        tristate "Realtek 8180/8185 PCI support"
        depends on MAC80211 && PCI && WLAN_80211 && EXPERIMENTAL
        select EEPROM_93CX6
        ---help---
          This is a driver for RTL8180 and RTL8185 based cards.
          These are PCI based chips found in cards such as:

          (RTL8185 802.11g)
          A-Link WL54PC

          (RTL8180 802.11b)
          Belkin F5D6020 v3
          Belkin F5D6020 v3
          Dlink DWL-610
          Dlink DWL-510
          Netgear MA521
          Level-One WPC-0101
          Acer Aspire 1357 LMi
          VCTnet PC-11B1
          Ovislink AirLive WL-1120PCM
          Mentor WL-PCI
          Linksys WPC11 v4
          TrendNET TEW-288PI
          D-Link DWL-520 Rev D
          Repotec RP-WP7126
          TP-Link TL-WN250/251
          Zonet ZEW1000
          Longshine LCS-8031-R
          HomeLine HLW-PCC200
          GigaFast WF721-AEX
          Planet WL-3553
          Encore ENLWI-PCI1-NT
          TrendNET TEW-266PC
          Gigabyte GN-WLMR101
          Siemens-fujitsu Amilo D1840W
          Edimax EW-7126
          PheeNet WL-11PCIR
          Tonze PC-2100T
          Planet WL-8303
          Dlink DWL-650 v M1
          Edimax EW-7106
          Q-Tec 770WC
          Topcom Skyr@cer 4011b
          Roper FreeLan 802.11b (edition 2004)
          Wistron Neweb Corp CB-200B
          Pentagram HorNET
          QTec 775WC
          TwinMOS Booming B Series
          Micronet SP906BB
          Sweex LC700010
          Surecom EP-9428
          Safecom SWLCR-1100

          Thanks to Realtek for their support!

config RTL8187
        tristate "Realtek 8187 and 8187B USB support"
        depends on MAC80211 && USB && WLAN_80211 && EXPERIMENTAL
        select EEPROM_93CX6
        ---help---
          This is a driver for RTL8187 and RTL8187B based cards.
          These are USB based chips found in devices such as:

          Netgear WG111v2
          Level 1 WNC-0301USB
          Micronet SP907GK V5
          Encore ENUWI-G2
          Trendnet TEW-424UB
          ASUS P5B Deluxe
          Toshiba Satellite Pro series of laptops
          Asus Wireless Link

          Thanks to Realtek for their support!

config ADM8211
        tristate "ADMtek ADM8211 support"
        depends on MAC80211 && PCI && WLAN_80211 && EXPERIMENTAL
        select CRC32
        select EEPROM_93CX6
        ---help---
          This driver is for ADM8211A, ADM8211B, and ADM8211C based cards.
          These are PCI/mini-PCI/Cardbus 802.11b chips found in cards such as:

          Xterasys Cardbus XN-2411b
          Blitz NetWave Point PC
          TrendNet 221pc
          Belkin F5D6001
          SMC 2635W
          Linksys WPC11 v1
          Fiberline FL-WL-200X
          3com Office Connect (3CRSHPW796)
          Corega WLPCIB-11
          SMC 2602W V2 EU
          D-Link DWL-520 Revision C

          However, some of these cards have been replaced with other chips
          like the RTL8180L (Xterasys Cardbus XN-2411b, Belkin F5D6001) or
          the Ralink RT2400 (SMC2635W) without a model number change.

          Thanks to Infineon-ADMtek for their support of this driver.

config MAC80211_HWSIM
        tristate "Simulated radio testing tool for mac80211"
        depends on MAC80211 && WLAN_80211
        ---help---
          This driver is a developer testing tool that can be used to test
          IEEE 802.11 networking stack (mac80211) functionality. This is not
          needed for normal wireless LAN usage and is only for testing. See
          Documentation/networking/mac80211_hwsim for more information on how
          to use this tool.

          To compile this driver as a module, choose M here: the module will be
          called mac80211_hwsim.  If unsure, say N.

source "drivers/net/wireless/p54/Kconfig"
source "drivers/net/wireless/ath5k/Kconfig"
source "drivers/net/wireless/ath9k/Kconfig"
source "drivers/net/wireless/iwlwifi/Kconfig"
source "drivers/net/wireless/hostap/Kconfig"
source "drivers/net/wireless/b43/Kconfig"
source "drivers/net/wireless/b43legacy/Kconfig"
source "drivers/net/wireless/zd1211rw/Kconfig"
source "drivers/net/wireless/rt2x00/Kconfig"

endmenu