1 /******************************************************************************
3 * Copyright(c) 2003 - 2009 Intel Corporation. All rights reserved.
5 * Portions of this file are derived from the ipw3945 project, as well
6 * as portions of the ieee80211 subsystem header files.
8 * This program is free software; you can redistribute it and/or modify it
9 * under the terms of version 2 of the GNU General Public License as
10 * published by the Free Software Foundation.
12 * This program is distributed in the hope that it will be useful, but WITHOUT
13 * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
14 * FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for
17 * You should have received a copy of the GNU General Public License along with
18 * this program; if not, write to the Free Software Foundation, Inc.,
19 * 51 Franklin Street, Fifth Floor, Boston, MA 02110, USA
21 * The full GNU General Public License is included in this distribution in the
22 * file called LICENSE.
24 * Contact Information:
25 * Intel Linux Wireless <ilw@linux.intel.com>
26 * Intel Corporation, 5200 N.E. Elam Young Parkway, Hillsboro, OR 97124-6497
28 *****************************************************************************/
30 #include <linux/kernel.h>
31 #include <linux/module.h>
32 #include <linux/init.h>
33 #include <linux/pci.h>
34 #include <linux/dma-mapping.h>
35 #include <linux/delay.h>
36 #include <linux/skbuff.h>
37 #include <linux/netdevice.h>
38 #include <linux/wireless.h>
39 #include <linux/firmware.h>
40 #include <linux/etherdevice.h>
41 #include <linux/if_arp.h>
43 #include <net/mac80211.h>
45 #include <asm/div64.h>
47 #define DRV_NAME "iwlagn"
49 #include "iwl-eeprom.h"
53 #include "iwl-helpers.h"
55 #include "iwl-calib.h"
58 /******************************************************************************
62 ******************************************************************************/
65 * module name, copyright, version, etc.
67 #define DRV_DESCRIPTION "Intel(R) Wireless WiFi Link AGN driver for Linux"
69 #ifdef CONFIG_IWLWIFI_DEBUG
75 #ifdef CONFIG_IWLWIFI_SPECTRUM_MEASUREMENT
81 #define DRV_VERSION IWLWIFI_VERSION VD VS
84 MODULE_DESCRIPTION(DRV_DESCRIPTION);
85 MODULE_VERSION(DRV_VERSION);
86 MODULE_AUTHOR(DRV_COPYRIGHT " " DRV_AUTHOR);
87 MODULE_LICENSE("GPL");
88 MODULE_ALIAS("iwl4965");
90 /*************** STATION TABLE MANAGEMENT ****
91 * mac80211 should be examined to determine if sta_info is duplicating
92 * the functionality provided here
95 /**************************************************************/
98 * iwl_commit_rxon - commit staging_rxon to hardware
100 * The RXON command in staging_rxon is committed to the hardware and
101 * the active_rxon structure is updated with the new data. This
102 * function correctly transitions out of the RXON_ASSOC_MSK state if
103 * a HW tune is required based on the RXON structure changes.
105 static int iwl_commit_rxon(struct iwl_priv *priv)
107 /* cast away the const for active_rxon in this function */
108 struct iwl_rxon_cmd *active_rxon = (void *)&priv->active_rxon;
111 !!(priv->staging_rxon.filter_flags & RXON_FILTER_ASSOC_MSK);
113 if (!iwl_is_alive(priv))
116 /* always get timestamp with Rx frame */
117 priv->staging_rxon.flags |= RXON_FLG_TSF2HOST_MSK;
118 /* allow CTS-to-self if possible. this is relevant only for
119 * 5000, but will not damage 4965 */
120 priv->staging_rxon.flags |= RXON_FLG_SELF_CTS_EN;
122 ret = iwl_check_rxon_cmd(priv);
124 IWL_ERR(priv, "Invalid RXON configuration. Not committing.\n");
128 /* If we don't need to send a full RXON, we can use
129 * iwl_rxon_assoc_cmd which is used to reconfigure filter
130 * and other flags for the current radio configuration. */
131 if (!iwl_full_rxon_required(priv)) {
132 ret = iwl_send_rxon_assoc(priv);
134 IWL_ERR(priv, "Error setting RXON_ASSOC (%d)\n", ret);
138 memcpy(active_rxon, &priv->staging_rxon, sizeof(*active_rxon));
142 /* station table will be cleared */
143 priv->assoc_station_added = 0;
145 /* If we are currently associated and the new config requires
146 * an RXON_ASSOC and the new config wants the associated mask enabled,
147 * we must clear the associated from the active configuration
148 * before we apply the new config */
149 if (iwl_is_associated(priv) && new_assoc) {
150 IWL_DEBUG_INFO(priv, "Toggling associated bit on current RXON\n");
151 active_rxon->filter_flags &= ~RXON_FILTER_ASSOC_MSK;
153 ret = iwl_send_cmd_pdu(priv, REPLY_RXON,
154 sizeof(struct iwl_rxon_cmd),
157 /* If the mask clearing failed then we set
158 * active_rxon back to what it was previously */
160 active_rxon->filter_flags |= RXON_FILTER_ASSOC_MSK;
161 IWL_ERR(priv, "Error clearing ASSOC_MSK (%d)\n", ret);
166 IWL_DEBUG_INFO(priv, "Sending RXON\n"
167 "* with%s RXON_FILTER_ASSOC_MSK\n"
170 (new_assoc ? "" : "out"),
171 le16_to_cpu(priv->staging_rxon.channel),
172 priv->staging_rxon.bssid_addr);
174 iwl_set_rxon_hwcrypto(priv, !priv->hw_params.sw_crypto);
176 /* Apply the new configuration
177 * RXON unassoc clears the station table in uCode, send it before
178 * we add the bcast station. If assoc bit is set, we will send RXON
179 * after having added the bcast and bssid station.
182 ret = iwl_send_cmd_pdu(priv, REPLY_RXON,
183 sizeof(struct iwl_rxon_cmd), &priv->staging_rxon);
185 IWL_ERR(priv, "Error setting new RXON (%d)\n", ret);
188 memcpy(active_rxon, &priv->staging_rxon, sizeof(*active_rxon));
191 iwl_clear_stations_table(priv);
193 if (!priv->error_recovering)
194 priv->start_calib = 0;
196 /* Add the broadcast address so we can send broadcast frames */
197 if (iwl_rxon_add_station(priv, iwl_bcast_addr, 0) ==
198 IWL_INVALID_STATION) {
199 IWL_ERR(priv, "Error adding BROADCAST address for transmit.\n");
203 /* If we have set the ASSOC_MSK and we are in BSS mode then
204 * add the IWL_AP_ID to the station rate table */
206 if (priv->iw_mode == NL80211_IFTYPE_STATION) {
207 ret = iwl_rxon_add_station(priv,
208 priv->active_rxon.bssid_addr, 1);
209 if (ret == IWL_INVALID_STATION) {
211 "Error adding AP address for TX.\n");
214 priv->assoc_station_added = 1;
215 if (priv->default_wep_key &&
216 iwl_send_static_wepkey_cmd(priv, 0))
218 "Could not send WEP static key.\n");
221 /* Apply the new configuration
222 * RXON assoc doesn't clear the station table in uCode,
224 ret = iwl_send_cmd_pdu(priv, REPLY_RXON,
225 sizeof(struct iwl_rxon_cmd), &priv->staging_rxon);
227 IWL_ERR(priv, "Error setting new RXON (%d)\n", ret);
230 memcpy(active_rxon, &priv->staging_rxon, sizeof(*active_rxon));
233 iwl_init_sensitivity(priv);
235 /* If we issue a new RXON command which required a tune then we must
236 * send a new TXPOWER command or we won't be able to Tx any frames */
237 ret = iwl_set_tx_power(priv, priv->tx_power_user_lmt, true);
239 IWL_ERR(priv, "Error sending TX power (%d)\n", ret);
246 void iwl_update_chain_flags(struct iwl_priv *priv)
249 iwl_set_rxon_chain(priv);
250 iwl_commit_rxon(priv);
253 static void iwl_clear_free_frames(struct iwl_priv *priv)
255 struct list_head *element;
257 IWL_DEBUG_INFO(priv, "%d frames on pre-allocated heap on clear.\n",
260 while (!list_empty(&priv->free_frames)) {
261 element = priv->free_frames.next;
263 kfree(list_entry(element, struct iwl_frame, list));
264 priv->frames_count--;
267 if (priv->frames_count) {
268 IWL_WARN(priv, "%d frames still in use. Did we lose one?\n",
270 priv->frames_count = 0;
274 static struct iwl_frame *iwl_get_free_frame(struct iwl_priv *priv)
276 struct iwl_frame *frame;
277 struct list_head *element;
278 if (list_empty(&priv->free_frames)) {
279 frame = kzalloc(sizeof(*frame), GFP_KERNEL);
281 IWL_ERR(priv, "Could not allocate frame!\n");
285 priv->frames_count++;
289 element = priv->free_frames.next;
291 return list_entry(element, struct iwl_frame, list);
294 static void iwl_free_frame(struct iwl_priv *priv, struct iwl_frame *frame)
296 memset(frame, 0, sizeof(*frame));
297 list_add(&frame->list, &priv->free_frames);
300 static unsigned int iwl_fill_beacon_frame(struct iwl_priv *priv,
301 struct ieee80211_hdr *hdr,
304 if (!iwl_is_associated(priv) || !priv->ibss_beacon ||
305 ((priv->iw_mode != NL80211_IFTYPE_ADHOC) &&
306 (priv->iw_mode != NL80211_IFTYPE_AP)))
309 if (priv->ibss_beacon->len > left)
312 memcpy(hdr, priv->ibss_beacon->data, priv->ibss_beacon->len);
314 return priv->ibss_beacon->len;
317 static unsigned int iwl_hw_get_beacon_cmd(struct iwl_priv *priv,
318 struct iwl_frame *frame, u8 rate)
320 struct iwl_tx_beacon_cmd *tx_beacon_cmd;
321 unsigned int frame_size;
323 tx_beacon_cmd = &frame->u.beacon;
324 memset(tx_beacon_cmd, 0, sizeof(*tx_beacon_cmd));
326 tx_beacon_cmd->tx.sta_id = priv->hw_params.bcast_sta_id;
327 tx_beacon_cmd->tx.stop_time.life_time = TX_CMD_LIFE_TIME_INFINITE;
329 frame_size = iwl_fill_beacon_frame(priv, tx_beacon_cmd->frame,
330 sizeof(frame->u) - sizeof(*tx_beacon_cmd));
332 BUG_ON(frame_size > MAX_MPDU_SIZE);
333 tx_beacon_cmd->tx.len = cpu_to_le16((u16)frame_size);
335 if ((rate == IWL_RATE_1M_PLCP) || (rate >= IWL_RATE_2M_PLCP))
336 tx_beacon_cmd->tx.rate_n_flags =
337 iwl_hw_set_rate_n_flags(rate, RATE_MCS_CCK_MSK);
339 tx_beacon_cmd->tx.rate_n_flags =
340 iwl_hw_set_rate_n_flags(rate, 0);
342 tx_beacon_cmd->tx.tx_flags = TX_CMD_FLG_SEQ_CTL_MSK |
344 TX_CMD_FLG_STA_RATE_MSK;
346 return sizeof(*tx_beacon_cmd) + frame_size;
348 static int iwl_send_beacon_cmd(struct iwl_priv *priv)
350 struct iwl_frame *frame;
351 unsigned int frame_size;
355 frame = iwl_get_free_frame(priv);
358 IWL_ERR(priv, "Could not obtain free frame buffer for beacon "
363 rate = iwl_rate_get_lowest_plcp(priv);
365 frame_size = iwl_hw_get_beacon_cmd(priv, frame, rate);
367 rc = iwl_send_cmd_pdu(priv, REPLY_TX_BEACON, frame_size,
370 iwl_free_frame(priv, frame);
375 static inline dma_addr_t iwl_tfd_tb_get_addr(struct iwl_tfd *tfd, u8 idx)
377 struct iwl_tfd_tb *tb = &tfd->tbs[idx];
379 dma_addr_t addr = get_unaligned_le32(&tb->lo);
380 if (sizeof(dma_addr_t) > sizeof(u32))
382 ((dma_addr_t)(le16_to_cpu(tb->hi_n_len) & 0xF) << 16) << 16;
387 static inline u16 iwl_tfd_tb_get_len(struct iwl_tfd *tfd, u8 idx)
389 struct iwl_tfd_tb *tb = &tfd->tbs[idx];
391 return le16_to_cpu(tb->hi_n_len) >> 4;
394 static inline void iwl_tfd_set_tb(struct iwl_tfd *tfd, u8 idx,
395 dma_addr_t addr, u16 len)
397 struct iwl_tfd_tb *tb = &tfd->tbs[idx];
398 u16 hi_n_len = len << 4;
400 put_unaligned_le32(addr, &tb->lo);
401 if (sizeof(dma_addr_t) > sizeof(u32))
402 hi_n_len |= ((addr >> 16) >> 16) & 0xF;
404 tb->hi_n_len = cpu_to_le16(hi_n_len);
406 tfd->num_tbs = idx + 1;
409 static inline u8 iwl_tfd_get_num_tbs(struct iwl_tfd *tfd)
411 return tfd->num_tbs & 0x1f;
415 * iwl_hw_txq_free_tfd - Free all chunks referenced by TFD [txq->q.read_ptr]
416 * @priv - driver private data
419 * Does NOT advance any TFD circular buffer read/write indexes
420 * Does NOT free the TFD itself (which is within circular buffer)
422 void iwl_hw_txq_free_tfd(struct iwl_priv *priv, struct iwl_tx_queue *txq)
424 struct iwl_tfd *tfd_tmp = (struct iwl_tfd *)txq->tfds;
426 struct pci_dev *dev = priv->pci_dev;
427 int index = txq->q.read_ptr;
431 tfd = &tfd_tmp[index];
433 /* Sanity check on number of chunks */
434 num_tbs = iwl_tfd_get_num_tbs(tfd);
436 if (num_tbs >= IWL_NUM_OF_TBS) {
437 IWL_ERR(priv, "Too many chunks: %i\n", num_tbs);
438 /* @todo issue fatal error, it is quite serious situation */
444 pci_unmap_single(dev,
445 pci_unmap_addr(&txq->cmd[index]->meta, mapping),
446 pci_unmap_len(&txq->cmd[index]->meta, len),
447 PCI_DMA_BIDIRECTIONAL);
449 /* Unmap chunks, if any. */
450 for (i = 1; i < num_tbs; i++) {
451 pci_unmap_single(dev, iwl_tfd_tb_get_addr(tfd, i),
452 iwl_tfd_tb_get_len(tfd, i), PCI_DMA_TODEVICE);
455 dev_kfree_skb(txq->txb[txq->q.read_ptr].skb[i - 1]);
456 txq->txb[txq->q.read_ptr].skb[i - 1] = NULL;
461 int iwl_hw_txq_attach_buf_to_tfd(struct iwl_priv *priv,
462 struct iwl_tx_queue *txq,
463 dma_addr_t addr, u16 len,
467 struct iwl_tfd *tfd, *tfd_tmp;
471 tfd_tmp = (struct iwl_tfd *)txq->tfds;
472 tfd = &tfd_tmp[q->write_ptr];
475 memset(tfd, 0, sizeof(*tfd));
477 num_tbs = iwl_tfd_get_num_tbs(tfd);
479 /* Each TFD can point to a maximum 20 Tx buffers */
480 if (num_tbs >= IWL_NUM_OF_TBS) {
481 IWL_ERR(priv, "Error can not send more than %d chunks\n",
486 BUG_ON(addr & ~DMA_BIT_MASK(36));
487 if (unlikely(addr & ~IWL_TX_DMA_MASK))
488 IWL_ERR(priv, "Unaligned address = %llx\n",
489 (unsigned long long)addr);
491 iwl_tfd_set_tb(tfd, num_tbs, addr, len);
497 * Tell nic where to find circular buffer of Tx Frame Descriptors for
498 * given Tx queue, and enable the DMA channel used for that queue.
500 * 4965 supports up to 16 Tx queues in DRAM, mapped to up to 8 Tx DMA
501 * channels supported in hardware.
503 int iwl_hw_tx_queue_init(struct iwl_priv *priv,
504 struct iwl_tx_queue *txq)
508 int txq_id = txq->q.id;
510 spin_lock_irqsave(&priv->lock, flags);
511 ret = iwl_grab_nic_access(priv);
513 spin_unlock_irqrestore(&priv->lock, flags);
517 /* Circular buffer (TFD queue in DRAM) physical base address */
518 iwl_write_direct32(priv, FH_MEM_CBBC_QUEUE(txq_id),
519 txq->q.dma_addr >> 8);
521 iwl_release_nic_access(priv);
522 spin_unlock_irqrestore(&priv->lock, flags);
528 /******************************************************************************
530 * Misc. internal state and helper functions
532 ******************************************************************************/
534 static void iwl_ht_conf(struct iwl_priv *priv,
535 struct ieee80211_bss_conf *bss_conf)
537 struct ieee80211_sta_ht_cap *ht_conf;
538 struct iwl_ht_info *iwl_conf = &priv->current_ht_config;
539 struct ieee80211_sta *sta;
541 IWL_DEBUG_MAC80211(priv, "enter: \n");
543 if (!iwl_conf->is_ht)
548 * It is totally wrong to base global information on something
549 * that is valid only when associated, alas, this driver works
550 * that way and I don't know how to fix it.
554 sta = ieee80211_find_sta(priv->hw, priv->bssid);
559 ht_conf = &sta->ht_cap;
561 if (ht_conf->cap & IEEE80211_HT_CAP_SGI_20)
562 iwl_conf->sgf |= HT_SHORT_GI_20MHZ;
563 if (ht_conf->cap & IEEE80211_HT_CAP_SGI_40)
564 iwl_conf->sgf |= HT_SHORT_GI_40MHZ;
566 iwl_conf->is_green_field = !!(ht_conf->cap & IEEE80211_HT_CAP_GRN_FLD);
567 iwl_conf->max_amsdu_size =
568 !!(ht_conf->cap & IEEE80211_HT_CAP_MAX_AMSDU);
570 iwl_conf->supported_chan_width =
571 !!(ht_conf->cap & IEEE80211_HT_CAP_SUP_WIDTH_20_40);
574 * XXX: The HT configuration needs to be moved into iwl_mac_config()
575 * to be done there correctly.
578 iwl_conf->extension_chan_offset = IEEE80211_HT_PARAM_CHA_SEC_NONE;
579 if (conf_is_ht40_minus(&priv->hw->conf))
580 iwl_conf->extension_chan_offset = IEEE80211_HT_PARAM_CHA_SEC_BELOW;
581 else if (conf_is_ht40_plus(&priv->hw->conf))
582 iwl_conf->extension_chan_offset = IEEE80211_HT_PARAM_CHA_SEC_ABOVE;
584 /* If no above or below channel supplied disable FAT channel */
585 if (iwl_conf->extension_chan_offset != IEEE80211_HT_PARAM_CHA_SEC_ABOVE &&
586 iwl_conf->extension_chan_offset != IEEE80211_HT_PARAM_CHA_SEC_BELOW)
587 iwl_conf->supported_chan_width = 0;
589 iwl_conf->sm_ps = (u8)((ht_conf->cap & IEEE80211_HT_CAP_SM_PS) >> 2);
591 memcpy(&iwl_conf->mcs, &ht_conf->mcs, 16);
593 iwl_conf->tx_chan_width = iwl_conf->supported_chan_width != 0;
594 iwl_conf->ht_protection =
595 bss_conf->ht.operation_mode & IEEE80211_HT_OP_MODE_PROTECTION;
596 iwl_conf->non_GF_STA_present =
597 !!(bss_conf->ht.operation_mode & IEEE80211_HT_OP_MODE_NON_GF_STA_PRSNT);
601 IWL_DEBUG_MAC80211(priv, "leave\n");
604 #define MAX_UCODE_BEACON_INTERVAL 4096
606 static u16 iwl_adjust_beacon_interval(u16 beacon_val)
609 u16 beacon_factor = 0;
611 beacon_factor = (beacon_val + MAX_UCODE_BEACON_INTERVAL)
612 / MAX_UCODE_BEACON_INTERVAL;
613 new_val = beacon_val / beacon_factor;
616 new_val = MAX_UCODE_BEACON_INTERVAL;
621 static void iwl_setup_rxon_timing(struct iwl_priv *priv)
624 s32 interval_tm, rem;
626 struct ieee80211_conf *conf = NULL;
629 conf = ieee80211_get_hw_conf(priv->hw);
631 spin_lock_irqsave(&priv->lock, flags);
632 priv->rxon_timing.timestamp = cpu_to_le64(priv->timestamp);
633 priv->rxon_timing.listen_interval = cpu_to_le16(conf->listen_interval);
635 if (priv->iw_mode == NL80211_IFTYPE_STATION) {
636 beacon_int = iwl_adjust_beacon_interval(priv->beacon_int);
637 priv->rxon_timing.atim_window = 0;
639 beacon_int = iwl_adjust_beacon_interval(conf->beacon_int);
641 /* TODO: we need to get atim_window from upper stack
642 * for now we set to 0 */
643 priv->rxon_timing.atim_window = 0;
646 priv->rxon_timing.beacon_interval = cpu_to_le16(beacon_int);
648 tsf = priv->timestamp; /* tsf is modifed by do_div: copy it */
649 interval_tm = beacon_int * 1024;
650 rem = do_div(tsf, interval_tm);
651 priv->rxon_timing.beacon_init_val = cpu_to_le32(interval_tm - rem);
653 spin_unlock_irqrestore(&priv->lock, flags);
654 IWL_DEBUG_ASSOC(priv, "beacon interval %d beacon timer %d beacon tim %d\n",
655 le16_to_cpu(priv->rxon_timing.beacon_interval),
656 le32_to_cpu(priv->rxon_timing.beacon_init_val),
657 le16_to_cpu(priv->rxon_timing.atim_window));
660 static int iwl_set_mode(struct iwl_priv *priv, int mode)
662 iwl_connection_init_rx_config(priv, mode);
663 iwl_set_rxon_chain(priv);
664 memcpy(priv->staging_rxon.node_addr, priv->mac_addr, ETH_ALEN);
666 iwl_clear_stations_table(priv);
668 /* dont commit rxon if rf-kill is on*/
669 if (!iwl_is_ready_rf(priv))
672 cancel_delayed_work(&priv->scan_check);
673 if (iwl_scan_cancel_timeout(priv, 100)) {
674 IWL_WARN(priv, "Aborted scan still in progress after 100ms\n");
675 IWL_DEBUG_MAC80211(priv, "leaving - scan abort failed.\n");
679 iwl_commit_rxon(priv);
684 /******************************************************************************
686 * Generic RX handler implementations
688 ******************************************************************************/
689 static void iwl_rx_reply_alive(struct iwl_priv *priv,
690 struct iwl_rx_mem_buffer *rxb)
692 struct iwl_rx_packet *pkt = (struct iwl_rx_packet *)rxb->skb->data;
693 struct iwl_alive_resp *palive;
694 struct delayed_work *pwork;
696 palive = &pkt->u.alive_frame;
698 IWL_DEBUG_INFO(priv, "Alive ucode status 0x%08X revision "
700 palive->is_valid, palive->ver_type,
701 palive->ver_subtype);
703 if (palive->ver_subtype == INITIALIZE_SUBTYPE) {
704 IWL_DEBUG_INFO(priv, "Initialization Alive received.\n");
705 memcpy(&priv->card_alive_init,
707 sizeof(struct iwl_init_alive_resp));
708 pwork = &priv->init_alive_start;
710 IWL_DEBUG_INFO(priv, "Runtime Alive received.\n");
711 memcpy(&priv->card_alive, &pkt->u.alive_frame,
712 sizeof(struct iwl_alive_resp));
713 pwork = &priv->alive_start;
716 /* We delay the ALIVE response by 5ms to
717 * give the HW RF Kill time to activate... */
718 if (palive->is_valid == UCODE_VALID_OK)
719 queue_delayed_work(priv->workqueue, pwork,
720 msecs_to_jiffies(5));
722 IWL_WARN(priv, "uCode did not respond OK.\n");
725 static void iwl_bg_beacon_update(struct work_struct *work)
727 struct iwl_priv *priv =
728 container_of(work, struct iwl_priv, beacon_update);
729 struct sk_buff *beacon;
731 /* Pull updated AP beacon from mac80211. will fail if not in AP mode */
732 beacon = ieee80211_beacon_get(priv->hw, priv->vif);
735 IWL_ERR(priv, "update beacon failed\n");
739 mutex_lock(&priv->mutex);
740 /* new beacon skb is allocated every time; dispose previous.*/
741 if (priv->ibss_beacon)
742 dev_kfree_skb(priv->ibss_beacon);
744 priv->ibss_beacon = beacon;
745 mutex_unlock(&priv->mutex);
747 iwl_send_beacon_cmd(priv);
751 * iwl_bg_statistics_periodic - Timer callback to queue statistics
753 * This callback is provided in order to send a statistics request.
755 * This timer function is continually reset to execute within
756 * REG_RECALIB_PERIOD seconds since the last STATISTICS_NOTIFICATION
757 * was received. We need to ensure we receive the statistics in order
758 * to update the temperature used for calibrating the TXPOWER.
760 static void iwl_bg_statistics_periodic(unsigned long data)
762 struct iwl_priv *priv = (struct iwl_priv *)data;
764 if (test_bit(STATUS_EXIT_PENDING, &priv->status))
767 /* dont send host command if rf-kill is on */
768 if (!iwl_is_ready_rf(priv))
771 iwl_send_statistics_request(priv, CMD_ASYNC);
774 static void iwl_rx_beacon_notif(struct iwl_priv *priv,
775 struct iwl_rx_mem_buffer *rxb)
777 #ifdef CONFIG_IWLWIFI_DEBUG
778 struct iwl_rx_packet *pkt = (struct iwl_rx_packet *)rxb->skb->data;
779 struct iwl4965_beacon_notif *beacon =
780 (struct iwl4965_beacon_notif *)pkt->u.raw;
781 u8 rate = iwl_hw_get_rate(beacon->beacon_notify_hdr.rate_n_flags);
783 IWL_DEBUG_RX(priv, "beacon status %x retries %d iss %d "
784 "tsf %d %d rate %d\n",
785 le32_to_cpu(beacon->beacon_notify_hdr.u.status) & TX_STATUS_MSK,
786 beacon->beacon_notify_hdr.failure_frame,
787 le32_to_cpu(beacon->ibss_mgr_status),
788 le32_to_cpu(beacon->high_tsf),
789 le32_to_cpu(beacon->low_tsf), rate);
792 if ((priv->iw_mode == NL80211_IFTYPE_AP) &&
793 (!test_bit(STATUS_EXIT_PENDING, &priv->status)))
794 queue_work(priv->workqueue, &priv->beacon_update);
797 /* Handle notification from uCode that card's power state is changing
798 * due to software, hardware, or critical temperature RFKILL */
799 static void iwl_rx_card_state_notif(struct iwl_priv *priv,
800 struct iwl_rx_mem_buffer *rxb)
802 struct iwl_rx_packet *pkt = (struct iwl_rx_packet *)rxb->skb->data;
803 u32 flags = le32_to_cpu(pkt->u.card_state_notif.flags);
804 unsigned long status = priv->status;
806 IWL_DEBUG_RF_KILL(priv, "Card state received: HW:%s SW:%s\n",
807 (flags & HW_CARD_DISABLED) ? "Kill" : "On",
808 (flags & SW_CARD_DISABLED) ? "Kill" : "On");
810 if (flags & (SW_CARD_DISABLED | HW_CARD_DISABLED |
813 iwl_write32(priv, CSR_UCODE_DRV_GP1_SET,
814 CSR_UCODE_DRV_GP1_BIT_CMD_BLOCKED);
816 if (!iwl_grab_nic_access(priv)) {
818 priv, HBUS_TARG_MBX_C,
819 HBUS_TARG_MBX_C_REG_BIT_CMD_BLOCKED);
821 iwl_release_nic_access(priv);
824 if (!(flags & RXON_CARD_DISABLED)) {
825 iwl_write32(priv, CSR_UCODE_DRV_GP1_CLR,
826 CSR_UCODE_DRV_GP1_BIT_CMD_BLOCKED);
827 if (!iwl_grab_nic_access(priv)) {
829 priv, HBUS_TARG_MBX_C,
830 HBUS_TARG_MBX_C_REG_BIT_CMD_BLOCKED);
832 iwl_release_nic_access(priv);
836 if (flags & RF_CARD_DISABLED) {
837 iwl_write32(priv, CSR_UCODE_DRV_GP1_SET,
838 CSR_UCODE_DRV_GP1_REG_BIT_CT_KILL_EXIT);
839 iwl_read32(priv, CSR_UCODE_DRV_GP1);
840 if (!iwl_grab_nic_access(priv))
841 iwl_release_nic_access(priv);
845 if (flags & HW_CARD_DISABLED)
846 set_bit(STATUS_RF_KILL_HW, &priv->status);
848 clear_bit(STATUS_RF_KILL_HW, &priv->status);
851 if (flags & SW_CARD_DISABLED)
852 set_bit(STATUS_RF_KILL_SW, &priv->status);
854 clear_bit(STATUS_RF_KILL_SW, &priv->status);
856 if (!(flags & RXON_CARD_DISABLED))
857 iwl_scan_cancel(priv);
859 if ((test_bit(STATUS_RF_KILL_HW, &status) !=
860 test_bit(STATUS_RF_KILL_HW, &priv->status)) ||
861 (test_bit(STATUS_RF_KILL_SW, &status) !=
862 test_bit(STATUS_RF_KILL_SW, &priv->status)))
863 queue_work(priv->workqueue, &priv->rf_kill);
865 wake_up_interruptible(&priv->wait_command_queue);
868 int iwl_set_pwr_src(struct iwl_priv *priv, enum iwl_pwr_src src)
873 spin_lock_irqsave(&priv->lock, flags);
874 ret = iwl_grab_nic_access(priv);
878 if (src == IWL_PWR_SRC_VAUX) {
879 if (pci_pme_capable(priv->pci_dev, PCI_D3cold))
880 iwl_set_bits_mask_prph(priv, APMG_PS_CTRL_REG,
881 APMG_PS_CTRL_VAL_PWR_SRC_VAUX,
882 ~APMG_PS_CTRL_MSK_PWR_SRC);
884 iwl_set_bits_mask_prph(priv, APMG_PS_CTRL_REG,
885 APMG_PS_CTRL_VAL_PWR_SRC_VMAIN,
886 ~APMG_PS_CTRL_MSK_PWR_SRC);
889 iwl_release_nic_access(priv);
891 spin_unlock_irqrestore(&priv->lock, flags);
896 * iwl_setup_rx_handlers - Initialize Rx handler callbacks
898 * Setup the RX handlers for each of the reply types sent from the uCode
901 * This function chains into the hardware specific files for them to setup
902 * any hardware specific handlers as well.
904 static void iwl_setup_rx_handlers(struct iwl_priv *priv)
906 priv->rx_handlers[REPLY_ALIVE] = iwl_rx_reply_alive;
907 priv->rx_handlers[REPLY_ERROR] = iwl_rx_reply_error;
908 priv->rx_handlers[CHANNEL_SWITCH_NOTIFICATION] = iwl_rx_csa;
909 priv->rx_handlers[PM_SLEEP_NOTIFICATION] = iwl_rx_pm_sleep_notif;
910 priv->rx_handlers[PM_DEBUG_STATISTIC_NOTIFIC] =
911 iwl_rx_pm_debug_statistics_notif;
912 priv->rx_handlers[BEACON_NOTIFICATION] = iwl_rx_beacon_notif;
915 * The same handler is used for both the REPLY to a discrete
916 * statistics request from the host as well as for the periodic
917 * statistics notifications (after received beacons) from the uCode.
919 priv->rx_handlers[REPLY_STATISTICS_CMD] = iwl_rx_statistics;
920 priv->rx_handlers[STATISTICS_NOTIFICATION] = iwl_rx_statistics;
922 iwl_setup_spectrum_handlers(priv);
923 iwl_setup_rx_scan_handlers(priv);
925 /* status change handler */
926 priv->rx_handlers[CARD_STATE_NOTIFICATION] = iwl_rx_card_state_notif;
928 priv->rx_handlers[MISSED_BEACONS_NOTIFICATION] =
929 iwl_rx_missed_beacon_notif;
931 priv->rx_handlers[REPLY_RX_PHY_CMD] = iwl_rx_reply_rx_phy;
932 priv->rx_handlers[REPLY_RX_MPDU_CMD] = iwl_rx_reply_rx;
934 priv->rx_handlers[REPLY_COMPRESSED_BA] = iwl_rx_reply_compressed_ba;
935 /* Set up hardware specific Rx handlers */
936 priv->cfg->ops->lib->rx_handler_setup(priv);
940 * iwl_rx_handle - Main entry function for receiving responses from uCode
942 * Uses the priv->rx_handlers callback function array to invoke
943 * the appropriate handlers, including command responses,
944 * frame-received notifications, and other notifications.
946 void iwl_rx_handle(struct iwl_priv *priv)
948 struct iwl_rx_mem_buffer *rxb;
949 struct iwl_rx_packet *pkt;
950 struct iwl_rx_queue *rxq = &priv->rxq;
957 /* uCode's read index (stored in shared DRAM) indicates the last Rx
958 * buffer that the driver may process (last buffer filled by ucode). */
959 r = le16_to_cpu(rxq->rb_stts->closed_rb_num) & 0x0FFF;
962 /* Rx interrupt, but nothing sent from uCode */
964 IWL_DEBUG_RX(priv, "r = %d, i = %d\n", r, i);
966 if (iwl_rx_queue_space(rxq) > (RX_QUEUE_SIZE / 2))
972 /* If an RXB doesn't have a Rx queue slot associated with it,
973 * then a bug has been introduced in the queue refilling
974 * routines -- catch it here */
977 rxq->queue[i] = NULL;
979 dma_sync_single_range_for_cpu(
980 &priv->pci_dev->dev, rxb->real_dma_addr,
981 rxb->aligned_dma_addr - rxb->real_dma_addr,
982 priv->hw_params.rx_buf_size,
984 pkt = (struct iwl_rx_packet *)rxb->skb->data;
986 /* Reclaim a command buffer only if this packet is a response
987 * to a (driver-originated) command.
988 * If the packet (e.g. Rx frame) originated from uCode,
989 * there is no command buffer to reclaim.
990 * Ucode should set SEQ_RX_FRAME bit if ucode-originated,
991 * but apparently a few don't get set; catch them here. */
992 reclaim = !(pkt->hdr.sequence & SEQ_RX_FRAME) &&
993 (pkt->hdr.cmd != REPLY_RX_PHY_CMD) &&
994 (pkt->hdr.cmd != REPLY_RX) &&
995 (pkt->hdr.cmd != REPLY_RX_MPDU_CMD) &&
996 (pkt->hdr.cmd != REPLY_COMPRESSED_BA) &&
997 (pkt->hdr.cmd != STATISTICS_NOTIFICATION) &&
998 (pkt->hdr.cmd != REPLY_TX);
1000 /* Based on type of command response or notification,
1001 * handle those that need handling via function in
1002 * rx_handlers table. See iwl_setup_rx_handlers() */
1003 if (priv->rx_handlers[pkt->hdr.cmd]) {
1004 IWL_DEBUG_RX(priv, "r = %d, i = %d, %s, 0x%02x\n", r,
1005 i, get_cmd_string(pkt->hdr.cmd), pkt->hdr.cmd);
1006 priv->rx_handlers[pkt->hdr.cmd] (priv, rxb);
1008 /* No handling needed */
1010 "r %d i %d No handler needed for %s, 0x%02x\n",
1011 r, i, get_cmd_string(pkt->hdr.cmd),
1016 /* Invoke any callbacks, transfer the skb to caller, and
1017 * fire off the (possibly) blocking iwl_send_cmd()
1018 * as we reclaim the driver command queue */
1019 if (rxb && rxb->skb)
1020 iwl_tx_cmd_complete(priv, rxb);
1022 IWL_WARN(priv, "Claim null rxb?\n");
1025 /* For now we just don't re-use anything. We can tweak this
1026 * later to try and re-use notification packets and SKBs that
1027 * fail to Rx correctly */
1028 if (rxb->skb != NULL) {
1029 priv->alloc_rxb_skb--;
1030 dev_kfree_skb_any(rxb->skb);
1034 pci_unmap_single(priv->pci_dev, rxb->real_dma_addr,
1035 priv->hw_params.rx_buf_size + 256,
1036 PCI_DMA_FROMDEVICE);
1037 spin_lock_irqsave(&rxq->lock, flags);
1038 list_add_tail(&rxb->list, &priv->rxq.rx_used);
1039 spin_unlock_irqrestore(&rxq->lock, flags);
1040 i = (i + 1) & RX_QUEUE_MASK;
1041 /* If there are a lot of unused frames,
1042 * restock the Rx queue so ucode wont assert. */
1047 iwl_rx_queue_restock(priv);
1053 /* Backtrack one entry */
1055 iwl_rx_queue_restock(priv);
1058 /* call this function to flush any scheduled tasklet */
1059 static inline void iwl_synchronize_irq(struct iwl_priv *priv)
1061 /* wait to make sure we flush pending tasklet*/
1062 synchronize_irq(priv->pci_dev->irq);
1063 tasklet_kill(&priv->irq_tasklet);
1066 static void iwl_error_recovery(struct iwl_priv *priv)
1068 unsigned long flags;
1070 memcpy(&priv->staging_rxon, &priv->recovery_rxon,
1071 sizeof(priv->staging_rxon));
1072 priv->staging_rxon.filter_flags &= ~RXON_FILTER_ASSOC_MSK;
1073 iwl_commit_rxon(priv);
1075 iwl_rxon_add_station(priv, priv->bssid, 1);
1077 spin_lock_irqsave(&priv->lock, flags);
1078 priv->assoc_id = le16_to_cpu(priv->staging_rxon.assoc_id);
1079 priv->error_recovering = 0;
1080 spin_unlock_irqrestore(&priv->lock, flags);
1083 static void iwl_irq_tasklet(struct iwl_priv *priv)
1085 u32 inta, handled = 0;
1087 unsigned long flags;
1088 #ifdef CONFIG_IWLWIFI_DEBUG
1092 spin_lock_irqsave(&priv->lock, flags);
1094 /* Ack/clear/reset pending uCode interrupts.
1095 * Note: Some bits in CSR_INT are "OR" of bits in CSR_FH_INT_STATUS,
1096 * and will clear only when CSR_FH_INT_STATUS gets cleared. */
1097 inta = iwl_read32(priv, CSR_INT);
1098 iwl_write32(priv, CSR_INT, inta);
1100 /* Ack/clear/reset pending flow-handler (DMA) interrupts.
1101 * Any new interrupts that happen after this, either while we're
1102 * in this tasklet, or later, will show up in next ISR/tasklet. */
1103 inta_fh = iwl_read32(priv, CSR_FH_INT_STATUS);
1104 iwl_write32(priv, CSR_FH_INT_STATUS, inta_fh);
1106 #ifdef CONFIG_IWLWIFI_DEBUG
1107 if (priv->debug_level & IWL_DL_ISR) {
1108 /* just for debug */
1109 inta_mask = iwl_read32(priv, CSR_INT_MASK);
1110 IWL_DEBUG_ISR(priv, "inta 0x%08x, enabled 0x%08x, fh 0x%08x\n",
1111 inta, inta_mask, inta_fh);
1115 /* Since CSR_INT and CSR_FH_INT_STATUS reads and clears are not
1116 * atomic, make sure that inta covers all the interrupts that
1117 * we've discovered, even if FH interrupt came in just after
1118 * reading CSR_INT. */
1119 if (inta_fh & CSR49_FH_INT_RX_MASK)
1120 inta |= CSR_INT_BIT_FH_RX;
1121 if (inta_fh & CSR49_FH_INT_TX_MASK)
1122 inta |= CSR_INT_BIT_FH_TX;
1124 /* Now service all interrupt bits discovered above. */
1125 if (inta & CSR_INT_BIT_HW_ERR) {
1126 IWL_ERR(priv, "Microcode HW error detected. Restarting.\n");
1128 /* Tell the device to stop sending interrupts */
1129 iwl_disable_interrupts(priv);
1131 iwl_irq_handle_error(priv);
1133 handled |= CSR_INT_BIT_HW_ERR;
1135 spin_unlock_irqrestore(&priv->lock, flags);
1140 #ifdef CONFIG_IWLWIFI_DEBUG
1141 if (priv->debug_level & (IWL_DL_ISR)) {
1142 /* NIC fires this, but we don't use it, redundant with WAKEUP */
1143 if (inta & CSR_INT_BIT_SCD)
1144 IWL_DEBUG_ISR(priv, "Scheduler finished to transmit "
1145 "the frame/frames.\n");
1147 /* Alive notification via Rx interrupt will do the real work */
1148 if (inta & CSR_INT_BIT_ALIVE)
1149 IWL_DEBUG_ISR(priv, "Alive interrupt\n");
1152 /* Safely ignore these bits for debug checks below */
1153 inta &= ~(CSR_INT_BIT_SCD | CSR_INT_BIT_ALIVE);
1155 /* HW RF KILL switch toggled */
1156 if (inta & CSR_INT_BIT_RF_KILL) {
1158 if (!(iwl_read32(priv, CSR_GP_CNTRL) &
1159 CSR_GP_CNTRL_REG_FLAG_HW_RF_KILL_SW))
1162 IWL_DEBUG_RF_KILL(priv, "RF_KILL bit toggled to %s.\n",
1163 hw_rf_kill ? "disable radio" : "enable radio");
1165 /* driver only loads ucode once setting the interface up.
1166 * the driver allows loading the ucode even if the radio
1167 * is killed. Hence update the killswitch state here. The
1168 * rfkill handler will care about restarting if needed.
1170 if (!test_bit(STATUS_ALIVE, &priv->status)) {
1172 set_bit(STATUS_RF_KILL_HW, &priv->status);
1174 clear_bit(STATUS_RF_KILL_HW, &priv->status);
1175 queue_work(priv->workqueue, &priv->rf_kill);
1178 handled |= CSR_INT_BIT_RF_KILL;
1181 /* Chip got too hot and stopped itself */
1182 if (inta & CSR_INT_BIT_CT_KILL) {
1183 IWL_ERR(priv, "Microcode CT kill error detected.\n");
1184 handled |= CSR_INT_BIT_CT_KILL;
1187 /* Error detected by uCode */
1188 if (inta & CSR_INT_BIT_SW_ERR) {
1189 IWL_ERR(priv, "Microcode SW error detected. "
1190 " Restarting 0x%X.\n", inta);
1191 iwl_irq_handle_error(priv);
1192 handled |= CSR_INT_BIT_SW_ERR;
1195 /* uCode wakes up after power-down sleep */
1196 if (inta & CSR_INT_BIT_WAKEUP) {
1197 IWL_DEBUG_ISR(priv, "Wakeup interrupt\n");
1198 iwl_rx_queue_update_write_ptr(priv, &priv->rxq);
1199 iwl_txq_update_write_ptr(priv, &priv->txq[0]);
1200 iwl_txq_update_write_ptr(priv, &priv->txq[1]);
1201 iwl_txq_update_write_ptr(priv, &priv->txq[2]);
1202 iwl_txq_update_write_ptr(priv, &priv->txq[3]);
1203 iwl_txq_update_write_ptr(priv, &priv->txq[4]);
1204 iwl_txq_update_write_ptr(priv, &priv->txq[5]);
1206 handled |= CSR_INT_BIT_WAKEUP;
1209 /* All uCode command responses, including Tx command responses,
1210 * Rx "responses" (frame-received notification), and other
1211 * notifications from uCode come through here*/
1212 if (inta & (CSR_INT_BIT_FH_RX | CSR_INT_BIT_SW_RX)) {
1213 iwl_rx_handle(priv);
1214 handled |= (CSR_INT_BIT_FH_RX | CSR_INT_BIT_SW_RX);
1217 if (inta & CSR_INT_BIT_FH_TX) {
1218 IWL_DEBUG_ISR(priv, "Tx interrupt\n");
1219 handled |= CSR_INT_BIT_FH_TX;
1220 /* FH finished to write, send event */
1221 priv->ucode_write_complete = 1;
1222 wake_up_interruptible(&priv->wait_command_queue);
1225 if (inta & ~handled)
1226 IWL_ERR(priv, "Unhandled INTA bits 0x%08x\n", inta & ~handled);
1228 if (inta & ~CSR_INI_SET_MASK) {
1229 IWL_WARN(priv, "Disabled INTA bits 0x%08x were pending\n",
1230 inta & ~CSR_INI_SET_MASK);
1231 IWL_WARN(priv, " with FH_INT = 0x%08x\n", inta_fh);
1234 /* Re-enable all interrupts */
1235 /* only Re-enable if diabled by irq */
1236 if (test_bit(STATUS_INT_ENABLED, &priv->status))
1237 iwl_enable_interrupts(priv);
1239 #ifdef CONFIG_IWLWIFI_DEBUG
1240 if (priv->debug_level & (IWL_DL_ISR)) {
1241 inta = iwl_read32(priv, CSR_INT);
1242 inta_mask = iwl_read32(priv, CSR_INT_MASK);
1243 inta_fh = iwl_read32(priv, CSR_FH_INT_STATUS);
1244 IWL_DEBUG_ISR(priv, "End inta 0x%08x, enabled 0x%08x, fh 0x%08x, "
1245 "flags 0x%08lx\n", inta, inta_mask, inta_fh, flags);
1248 spin_unlock_irqrestore(&priv->lock, flags);
1251 /******************************************************************************
1253 * uCode download functions
1255 ******************************************************************************/
1257 static void iwl_dealloc_ucode_pci(struct iwl_priv *priv)
1259 iwl_free_fw_desc(priv->pci_dev, &priv->ucode_code);
1260 iwl_free_fw_desc(priv->pci_dev, &priv->ucode_data);
1261 iwl_free_fw_desc(priv->pci_dev, &priv->ucode_data_backup);
1262 iwl_free_fw_desc(priv->pci_dev, &priv->ucode_init);
1263 iwl_free_fw_desc(priv->pci_dev, &priv->ucode_init_data);
1264 iwl_free_fw_desc(priv->pci_dev, &priv->ucode_boot);
1267 static void iwl_nic_start(struct iwl_priv *priv)
1269 /* Remove all resets to allow NIC to operate */
1270 iwl_write32(priv, CSR_RESET, 0);
1275 * iwl_read_ucode - Read uCode images from disk file.
1277 * Copy into buffers for card to fetch via bus-mastering
1279 static int iwl_read_ucode(struct iwl_priv *priv)
1281 struct iwl_ucode *ucode;
1282 int ret = -EINVAL, index;
1283 const struct firmware *ucode_raw;
1284 const char *name_pre = priv->cfg->fw_name_pre;
1285 const unsigned int api_max = priv->cfg->ucode_api_max;
1286 const unsigned int api_min = priv->cfg->ucode_api_min;
1290 u32 api_ver, inst_size, data_size, init_size, init_data_size, boot_size;
1292 /* Ask kernel firmware_class module to get the boot firmware off disk.
1293 * request_firmware() is synchronous, file is in memory on return. */
1294 for (index = api_max; index >= api_min; index--) {
1295 sprintf(buf, "%s%d%s", name_pre, index, ".ucode");
1296 ret = request_firmware(&ucode_raw, buf, &priv->pci_dev->dev);
1298 IWL_ERR(priv, "%s firmware file req failed: %d\n",
1305 if (index < api_max)
1306 IWL_ERR(priv, "Loaded firmware %s, "
1307 "which is deprecated. "
1308 "Please use API v%u instead.\n",
1311 IWL_DEBUG_INFO(priv, "Got firmware '%s' file (%zd bytes) from disk\n",
1312 buf, ucode_raw->size);
1320 /* Make sure that we got at least our header! */
1321 if (ucode_raw->size < sizeof(*ucode)) {
1322 IWL_ERR(priv, "File size way too small!\n");
1327 /* Data from ucode file: header followed by uCode images */
1328 ucode = (void *)ucode_raw->data;
1330 priv->ucode_ver = le32_to_cpu(ucode->ver);
1331 api_ver = IWL_UCODE_API(priv->ucode_ver);
1332 inst_size = le32_to_cpu(ucode->inst_size);
1333 data_size = le32_to_cpu(ucode->data_size);
1334 init_size = le32_to_cpu(ucode->init_size);
1335 init_data_size = le32_to_cpu(ucode->init_data_size);
1336 boot_size = le32_to_cpu(ucode->boot_size);
1338 /* api_ver should match the api version forming part of the
1339 * firmware filename ... but we don't check for that and only rely
1340 * on the API version read from firmware header from here on forward */
1342 if (api_ver < api_min || api_ver > api_max) {
1343 IWL_ERR(priv, "Driver unable to support your firmware API. "
1344 "Driver supports v%u, firmware is v%u.\n",
1346 priv->ucode_ver = 0;
1350 if (api_ver != api_max)
1351 IWL_ERR(priv, "Firmware has old API version. Expected v%u, "
1352 "got v%u. New firmware can be obtained "
1353 "from http://www.intellinuxwireless.org.\n",
1356 IWL_INFO(priv, "loaded firmware version %u.%u.%u.%u\n",
1357 IWL_UCODE_MAJOR(priv->ucode_ver),
1358 IWL_UCODE_MINOR(priv->ucode_ver),
1359 IWL_UCODE_API(priv->ucode_ver),
1360 IWL_UCODE_SERIAL(priv->ucode_ver));
1362 IWL_DEBUG_INFO(priv, "f/w package hdr ucode version raw = 0x%x\n",
1364 IWL_DEBUG_INFO(priv, "f/w package hdr runtime inst size = %u\n",
1366 IWL_DEBUG_INFO(priv, "f/w package hdr runtime data size = %u\n",
1368 IWL_DEBUG_INFO(priv, "f/w package hdr init inst size = %u\n",
1370 IWL_DEBUG_INFO(priv, "f/w package hdr init data size = %u\n",
1372 IWL_DEBUG_INFO(priv, "f/w package hdr boot inst size = %u\n",
1375 /* Verify size of file vs. image size info in file's header */
1376 if (ucode_raw->size < sizeof(*ucode) +
1377 inst_size + data_size + init_size +
1378 init_data_size + boot_size) {
1380 IWL_DEBUG_INFO(priv, "uCode file size %d too small\n",
1381 (int)ucode_raw->size);
1386 /* Verify that uCode images will fit in card's SRAM */
1387 if (inst_size > priv->hw_params.max_inst_size) {
1388 IWL_DEBUG_INFO(priv, "uCode instr len %d too large to fit in\n",
1394 if (data_size > priv->hw_params.max_data_size) {
1395 IWL_DEBUG_INFO(priv, "uCode data len %d too large to fit in\n",
1400 if (init_size > priv->hw_params.max_inst_size) {
1401 IWL_INFO(priv, "uCode init instr len %d too large to fit in\n",
1406 if (init_data_size > priv->hw_params.max_data_size) {
1407 IWL_INFO(priv, "uCode init data len %d too large to fit in\n",
1412 if (boot_size > priv->hw_params.max_bsm_size) {
1413 IWL_INFO(priv, "uCode boot instr len %d too large to fit in\n",
1419 /* Allocate ucode buffers for card's bus-master loading ... */
1421 /* Runtime instructions and 2 copies of data:
1422 * 1) unmodified from disk
1423 * 2) backup cache for save/restore during power-downs */
1424 priv->ucode_code.len = inst_size;
1425 iwl_alloc_fw_desc(priv->pci_dev, &priv->ucode_code);
1427 priv->ucode_data.len = data_size;
1428 iwl_alloc_fw_desc(priv->pci_dev, &priv->ucode_data);
1430 priv->ucode_data_backup.len = data_size;
1431 iwl_alloc_fw_desc(priv->pci_dev, &priv->ucode_data_backup);
1433 if (!priv->ucode_code.v_addr || !priv->ucode_data.v_addr ||
1434 !priv->ucode_data_backup.v_addr)
1437 /* Initialization instructions and data */
1438 if (init_size && init_data_size) {
1439 priv->ucode_init.len = init_size;
1440 iwl_alloc_fw_desc(priv->pci_dev, &priv->ucode_init);
1442 priv->ucode_init_data.len = init_data_size;
1443 iwl_alloc_fw_desc(priv->pci_dev, &priv->ucode_init_data);
1445 if (!priv->ucode_init.v_addr || !priv->ucode_init_data.v_addr)
1449 /* Bootstrap (instructions only, no data) */
1451 priv->ucode_boot.len = boot_size;
1452 iwl_alloc_fw_desc(priv->pci_dev, &priv->ucode_boot);
1454 if (!priv->ucode_boot.v_addr)
1458 /* Copy images into buffers for card's bus-master reads ... */
1460 /* Runtime instructions (first block of data in file) */
1461 src = &ucode->data[0];
1462 len = priv->ucode_code.len;
1463 IWL_DEBUG_INFO(priv, "Copying (but not loading) uCode instr len %Zd\n", len);
1464 memcpy(priv->ucode_code.v_addr, src, len);
1465 IWL_DEBUG_INFO(priv, "uCode instr buf vaddr = 0x%p, paddr = 0x%08x\n",
1466 priv->ucode_code.v_addr, (u32)priv->ucode_code.p_addr);
1468 /* Runtime data (2nd block)
1469 * NOTE: Copy into backup buffer will be done in iwl_up() */
1470 src = &ucode->data[inst_size];
1471 len = priv->ucode_data.len;
1472 IWL_DEBUG_INFO(priv, "Copying (but not loading) uCode data len %Zd\n", len);
1473 memcpy(priv->ucode_data.v_addr, src, len);
1474 memcpy(priv->ucode_data_backup.v_addr, src, len);
1476 /* Initialization instructions (3rd block) */
1478 src = &ucode->data[inst_size + data_size];
1479 len = priv->ucode_init.len;
1480 IWL_DEBUG_INFO(priv, "Copying (but not loading) init instr len %Zd\n",
1482 memcpy(priv->ucode_init.v_addr, src, len);
1485 /* Initialization data (4th block) */
1486 if (init_data_size) {
1487 src = &ucode->data[inst_size + data_size + init_size];
1488 len = priv->ucode_init_data.len;
1489 IWL_DEBUG_INFO(priv, "Copying (but not loading) init data len %Zd\n",
1491 memcpy(priv->ucode_init_data.v_addr, src, len);
1494 /* Bootstrap instructions (5th block) */
1495 src = &ucode->data[inst_size + data_size + init_size + init_data_size];
1496 len = priv->ucode_boot.len;
1497 IWL_DEBUG_INFO(priv, "Copying (but not loading) boot instr len %Zd\n", len);
1498 memcpy(priv->ucode_boot.v_addr, src, len);
1500 /* We have our copies now, allow OS release its copies */
1501 release_firmware(ucode_raw);
1505 IWL_ERR(priv, "failed to allocate pci memory\n");
1507 iwl_dealloc_ucode_pci(priv);
1510 release_firmware(ucode_raw);
1517 static int iwl_mac_beacon_update(struct ieee80211_hw *hw,
1518 struct sk_buff *skb);
1521 * iwl_alive_start - called after REPLY_ALIVE notification received
1522 * from protocol/runtime uCode (initialization uCode's
1523 * Alive gets handled by iwl_init_alive_start()).
1525 static void iwl_alive_start(struct iwl_priv *priv)
1529 IWL_DEBUG_INFO(priv, "Runtime Alive received.\n");
1531 if (priv->card_alive.is_valid != UCODE_VALID_OK) {
1532 /* We had an error bringing up the hardware, so take it
1533 * all the way back down so we can try again */
1534 IWL_DEBUG_INFO(priv, "Alive failed.\n");
1538 /* Initialize uCode has loaded Runtime uCode ... verify inst image.
1539 * This is a paranoid check, because we would not have gotten the
1540 * "runtime" alive if code weren't properly loaded. */
1541 if (iwl_verify_ucode(priv)) {
1542 /* Runtime instruction load was bad;
1543 * take it all the way back down so we can try again */
1544 IWL_DEBUG_INFO(priv, "Bad runtime uCode load.\n");
1548 iwl_clear_stations_table(priv);
1549 ret = priv->cfg->ops->lib->alive_notify(priv);
1552 "Could not complete ALIVE transition [ntf]: %d\n", ret);
1556 /* After the ALIVE response, we can send host commands to the uCode */
1557 set_bit(STATUS_ALIVE, &priv->status);
1559 if (iwl_is_rfkill(priv))
1562 ieee80211_wake_queues(priv->hw);
1564 priv->active_rate = priv->rates_mask;
1565 priv->active_rate_basic = priv->rates_mask & IWL_BASIC_RATES_MASK;
1567 if (iwl_is_associated(priv)) {
1568 struct iwl_rxon_cmd *active_rxon =
1569 (struct iwl_rxon_cmd *)&priv->active_rxon;
1570 /* apply any changes in staging */
1571 priv->staging_rxon.filter_flags |= RXON_FILTER_ASSOC_MSK;
1572 active_rxon->filter_flags &= ~RXON_FILTER_ASSOC_MSK;
1574 /* Initialize our rx_config data */
1575 iwl_connection_init_rx_config(priv, priv->iw_mode);
1576 iwl_set_rxon_chain(priv);
1577 memcpy(priv->staging_rxon.node_addr, priv->mac_addr, ETH_ALEN);
1580 /* Configure Bluetooth device coexistence support */
1581 iwl_send_bt_config(priv);
1583 iwl_reset_run_time_calib(priv);
1585 /* Configure the adapter for unassociated operation */
1586 iwl_commit_rxon(priv);
1588 /* At this point, the NIC is initialized and operational */
1589 iwl_rf_kill_ct_config(priv);
1591 iwl_leds_register(priv);
1593 IWL_DEBUG_INFO(priv, "ALIVE processing complete.\n");
1594 set_bit(STATUS_READY, &priv->status);
1595 wake_up_interruptible(&priv->wait_command_queue);
1597 if (priv->error_recovering)
1598 iwl_error_recovery(priv);
1600 iwl_power_update_mode(priv, 1);
1602 /* reassociate for ADHOC mode */
1603 if (priv->vif && (priv->iw_mode == NL80211_IFTYPE_ADHOC)) {
1604 struct sk_buff *beacon = ieee80211_beacon_get(priv->hw,
1607 iwl_mac_beacon_update(priv->hw, beacon);
1611 if (test_and_clear_bit(STATUS_MODE_PENDING, &priv->status))
1612 iwl_set_mode(priv, priv->iw_mode);
1617 queue_work(priv->workqueue, &priv->restart);
1620 static void iwl_cancel_deferred_work(struct iwl_priv *priv);
1622 static void __iwl_down(struct iwl_priv *priv)
1624 unsigned long flags;
1625 int exit_pending = test_bit(STATUS_EXIT_PENDING, &priv->status);
1627 IWL_DEBUG_INFO(priv, DRV_NAME " is going down\n");
1630 set_bit(STATUS_EXIT_PENDING, &priv->status);
1632 iwl_leds_unregister(priv);
1634 iwl_clear_stations_table(priv);
1636 /* Unblock any waiting calls */
1637 wake_up_interruptible_all(&priv->wait_command_queue);
1639 /* Wipe out the EXIT_PENDING status bit if we are not actually
1640 * exiting the module */
1642 clear_bit(STATUS_EXIT_PENDING, &priv->status);
1644 /* stop and reset the on-board processor */
1645 iwl_write32(priv, CSR_RESET, CSR_RESET_REG_FLAG_NEVO_RESET);
1647 /* tell the device to stop sending interrupts */
1648 spin_lock_irqsave(&priv->lock, flags);
1649 iwl_disable_interrupts(priv);
1650 spin_unlock_irqrestore(&priv->lock, flags);
1651 iwl_synchronize_irq(priv);
1653 if (priv->mac80211_registered)
1654 ieee80211_stop_queues(priv->hw);
1656 /* If we have not previously called iwl_init() then
1657 * clear all bits but the RF Kill and SUSPEND bits and return */
1658 if (!iwl_is_init(priv)) {
1659 priv->status = test_bit(STATUS_RF_KILL_HW, &priv->status) <<
1661 test_bit(STATUS_RF_KILL_SW, &priv->status) <<
1663 test_bit(STATUS_GEO_CONFIGURED, &priv->status) <<
1664 STATUS_GEO_CONFIGURED |
1665 test_bit(STATUS_IN_SUSPEND, &priv->status) <<
1667 test_bit(STATUS_EXIT_PENDING, &priv->status) <<
1668 STATUS_EXIT_PENDING;
1672 /* ...otherwise clear out all the status bits but the RF Kill and
1673 * SUSPEND bits and continue taking the NIC down. */
1674 priv->status &= test_bit(STATUS_RF_KILL_HW, &priv->status) <<
1676 test_bit(STATUS_RF_KILL_SW, &priv->status) <<
1678 test_bit(STATUS_GEO_CONFIGURED, &priv->status) <<
1679 STATUS_GEO_CONFIGURED |
1680 test_bit(STATUS_IN_SUSPEND, &priv->status) <<
1682 test_bit(STATUS_FW_ERROR, &priv->status) <<
1684 test_bit(STATUS_EXIT_PENDING, &priv->status) <<
1685 STATUS_EXIT_PENDING;
1687 spin_lock_irqsave(&priv->lock, flags);
1688 iwl_clear_bit(priv, CSR_GP_CNTRL,
1689 CSR_GP_CNTRL_REG_FLAG_MAC_ACCESS_REQ);
1690 spin_unlock_irqrestore(&priv->lock, flags);
1692 iwl_txq_ctx_stop(priv);
1695 spin_lock_irqsave(&priv->lock, flags);
1696 if (!iwl_grab_nic_access(priv)) {
1697 iwl_write_prph(priv, APMG_CLK_DIS_REG,
1698 APMG_CLK_VAL_DMA_CLK_RQT);
1699 iwl_release_nic_access(priv);
1701 spin_unlock_irqrestore(&priv->lock, flags);
1705 /* FIXME: apm_ops.suspend(priv) */
1706 if (exit_pending || test_bit(STATUS_IN_SUSPEND, &priv->status))
1707 priv->cfg->ops->lib->apm_ops.stop(priv);
1709 priv->cfg->ops->lib->apm_ops.reset(priv);
1711 memset(&priv->card_alive, 0, sizeof(struct iwl_alive_resp));
1713 if (priv->ibss_beacon)
1714 dev_kfree_skb(priv->ibss_beacon);
1715 priv->ibss_beacon = NULL;
1717 /* clear out any free frames */
1718 iwl_clear_free_frames(priv);
1721 static void iwl_down(struct iwl_priv *priv)
1723 mutex_lock(&priv->mutex);
1725 mutex_unlock(&priv->mutex);
1727 iwl_cancel_deferred_work(priv);
1730 #define MAX_HW_RESTARTS 5
1732 static int __iwl_up(struct iwl_priv *priv)
1737 if (test_bit(STATUS_EXIT_PENDING, &priv->status)) {
1738 IWL_WARN(priv, "Exit pending; will not bring the NIC up\n");
1742 if (!priv->ucode_data_backup.v_addr || !priv->ucode_data.v_addr) {
1743 IWL_ERR(priv, "ucode not available for device bringup\n");
1747 /* If platform's RF_KILL switch is NOT set to KILL */
1748 if (iwl_read32(priv, CSR_GP_CNTRL) & CSR_GP_CNTRL_REG_FLAG_HW_RF_KILL_SW)
1749 clear_bit(STATUS_RF_KILL_HW, &priv->status);
1751 set_bit(STATUS_RF_KILL_HW, &priv->status);
1753 if (iwl_is_rfkill(priv)) {
1754 iwl_enable_interrupts(priv);
1755 IWL_WARN(priv, "Radio disabled by %s RF Kill switch\n",
1756 test_bit(STATUS_RF_KILL_HW, &priv->status) ? "HW" : "SW");
1760 iwl_write32(priv, CSR_INT, 0xFFFFFFFF);
1762 ret = iwl_hw_nic_init(priv);
1764 IWL_ERR(priv, "Unable to init nic\n");
1768 /* make sure rfkill handshake bits are cleared */
1769 iwl_write32(priv, CSR_UCODE_DRV_GP1_CLR, CSR_UCODE_SW_BIT_RFKILL);
1770 iwl_write32(priv, CSR_UCODE_DRV_GP1_CLR,
1771 CSR_UCODE_DRV_GP1_BIT_CMD_BLOCKED);
1773 /* clear (again), then enable host interrupts */
1774 iwl_write32(priv, CSR_INT, 0xFFFFFFFF);
1775 iwl_enable_interrupts(priv);
1777 /* really make sure rfkill handshake bits are cleared */
1778 iwl_write32(priv, CSR_UCODE_DRV_GP1_CLR, CSR_UCODE_SW_BIT_RFKILL);
1779 iwl_write32(priv, CSR_UCODE_DRV_GP1_CLR, CSR_UCODE_SW_BIT_RFKILL);
1781 /* Copy original ucode data image from disk into backup cache.
1782 * This will be used to initialize the on-board processor's
1783 * data SRAM for a clean start when the runtime program first loads. */
1784 memcpy(priv->ucode_data_backup.v_addr, priv->ucode_data.v_addr,
1785 priv->ucode_data.len);
1787 for (i = 0; i < MAX_HW_RESTARTS; i++) {
1789 iwl_clear_stations_table(priv);
1791 /* load bootstrap state machine,
1792 * load bootstrap program into processor's memory,
1793 * prepare to load the "initialize" uCode */
1794 ret = priv->cfg->ops->lib->load_ucode(priv);
1797 IWL_ERR(priv, "Unable to set up bootstrap uCode: %d\n",
1802 /* Clear out the uCode error bit if it is set */
1803 clear_bit(STATUS_FW_ERROR, &priv->status);
1805 /* start card; "initialize" will load runtime ucode */
1806 iwl_nic_start(priv);
1808 IWL_DEBUG_INFO(priv, DRV_NAME " is coming up\n");
1813 set_bit(STATUS_EXIT_PENDING, &priv->status);
1815 clear_bit(STATUS_EXIT_PENDING, &priv->status);
1817 /* tried to restart and config the device for as long as our
1818 * patience could withstand */
1819 IWL_ERR(priv, "Unable to initialize device after %d attempts.\n", i);
1824 /*****************************************************************************
1826 * Workqueue callbacks
1828 *****************************************************************************/
1830 static void iwl_bg_init_alive_start(struct work_struct *data)
1832 struct iwl_priv *priv =
1833 container_of(data, struct iwl_priv, init_alive_start.work);
1835 if (test_bit(STATUS_EXIT_PENDING, &priv->status))
1838 mutex_lock(&priv->mutex);
1839 priv->cfg->ops->lib->init_alive_start(priv);
1840 mutex_unlock(&priv->mutex);
1843 static void iwl_bg_alive_start(struct work_struct *data)
1845 struct iwl_priv *priv =
1846 container_of(data, struct iwl_priv, alive_start.work);
1848 if (test_bit(STATUS_EXIT_PENDING, &priv->status))
1851 mutex_lock(&priv->mutex);
1852 iwl_alive_start(priv);
1853 mutex_unlock(&priv->mutex);
1856 static void iwl_bg_run_time_calib_work(struct work_struct *work)
1858 struct iwl_priv *priv = container_of(work, struct iwl_priv,
1859 run_time_calib_work);
1861 mutex_lock(&priv->mutex);
1863 if (test_bit(STATUS_EXIT_PENDING, &priv->status) ||
1864 test_bit(STATUS_SCANNING, &priv->status)) {
1865 mutex_unlock(&priv->mutex);
1869 if (priv->start_calib) {
1870 iwl_chain_noise_calibration(priv, &priv->statistics);
1872 iwl_sensitivity_calibration(priv, &priv->statistics);
1875 mutex_unlock(&priv->mutex);
1879 static void iwl_bg_up(struct work_struct *data)
1881 struct iwl_priv *priv = container_of(data, struct iwl_priv, up);
1883 if (test_bit(STATUS_EXIT_PENDING, &priv->status))
1886 mutex_lock(&priv->mutex);
1888 mutex_unlock(&priv->mutex);
1889 iwl_rfkill_set_hw_state(priv);
1892 static void iwl_bg_restart(struct work_struct *data)
1894 struct iwl_priv *priv = container_of(data, struct iwl_priv, restart);
1896 if (test_bit(STATUS_EXIT_PENDING, &priv->status))
1900 queue_work(priv->workqueue, &priv->up);
1903 static void iwl_bg_rx_replenish(struct work_struct *data)
1905 struct iwl_priv *priv =
1906 container_of(data, struct iwl_priv, rx_replenish);
1908 if (test_bit(STATUS_EXIT_PENDING, &priv->status))
1911 mutex_lock(&priv->mutex);
1912 iwl_rx_replenish(priv);
1913 mutex_unlock(&priv->mutex);
1916 #define IWL_DELAY_NEXT_SCAN (HZ*2)
1918 static void iwl_post_associate(struct iwl_priv *priv)
1920 struct ieee80211_conf *conf = NULL;
1922 unsigned long flags;
1924 if (priv->iw_mode == NL80211_IFTYPE_AP) {
1925 IWL_ERR(priv, "%s Should not be called in AP mode\n", __func__);
1929 IWL_DEBUG_ASSOC(priv, "Associated as %d to: %pM\n",
1930 priv->assoc_id, priv->active_rxon.bssid_addr);
1933 if (test_bit(STATUS_EXIT_PENDING, &priv->status))
1937 if (!priv->vif || !priv->is_open)
1940 iwl_power_cancel_timeout(priv);
1941 iwl_scan_cancel_timeout(priv, 200);
1943 conf = ieee80211_get_hw_conf(priv->hw);
1945 priv->staging_rxon.filter_flags &= ~RXON_FILTER_ASSOC_MSK;
1946 iwl_commit_rxon(priv);
1948 iwl_setup_rxon_timing(priv);
1949 ret = iwl_send_cmd_pdu(priv, REPLY_RXON_TIMING,
1950 sizeof(priv->rxon_timing), &priv->rxon_timing);
1952 IWL_WARN(priv, "REPLY_RXON_TIMING failed - "
1953 "Attempting to continue.\n");
1955 priv->staging_rxon.filter_flags |= RXON_FILTER_ASSOC_MSK;
1957 iwl_set_rxon_ht(priv, &priv->current_ht_config);
1959 iwl_set_rxon_chain(priv);
1960 priv->staging_rxon.assoc_id = cpu_to_le16(priv->assoc_id);
1962 IWL_DEBUG_ASSOC(priv, "assoc id %d beacon interval %d\n",
1963 priv->assoc_id, priv->beacon_int);
1965 if (priv->assoc_capability & WLAN_CAPABILITY_SHORT_PREAMBLE)
1966 priv->staging_rxon.flags |= RXON_FLG_SHORT_PREAMBLE_MSK;
1968 priv->staging_rxon.flags &= ~RXON_FLG_SHORT_PREAMBLE_MSK;
1970 if (priv->staging_rxon.flags & RXON_FLG_BAND_24G_MSK) {
1971 if (priv->assoc_capability & WLAN_CAPABILITY_SHORT_SLOT_TIME)
1972 priv->staging_rxon.flags |= RXON_FLG_SHORT_SLOT_MSK;
1974 priv->staging_rxon.flags &= ~RXON_FLG_SHORT_SLOT_MSK;
1976 if (priv->iw_mode == NL80211_IFTYPE_ADHOC)
1977 priv->staging_rxon.flags &= ~RXON_FLG_SHORT_SLOT_MSK;
1981 iwl_commit_rxon(priv);
1983 switch (priv->iw_mode) {
1984 case NL80211_IFTYPE_STATION:
1987 case NL80211_IFTYPE_ADHOC:
1989 /* assume default assoc id */
1992 iwl_rxon_add_station(priv, priv->bssid, 0);
1993 iwl_send_beacon_cmd(priv);
1998 IWL_ERR(priv, "%s Should not be called in %d mode\n",
1999 __func__, priv->iw_mode);
2003 if (priv->iw_mode == NL80211_IFTYPE_ADHOC)
2004 priv->assoc_station_added = 1;
2006 spin_lock_irqsave(&priv->lock, flags);
2007 iwl_activate_qos(priv, 0);
2008 spin_unlock_irqrestore(&priv->lock, flags);
2010 /* the chain noise calibration will enabled PM upon completion
2011 * If chain noise has already been run, then we need to enable
2012 * power management here */
2013 if (priv->chain_noise_data.state == IWL_CHAIN_NOISE_DONE)
2014 iwl_power_enable_management(priv);
2016 /* Enable Rx differential gain and sensitivity calibrations */
2017 iwl_chain_noise_reset(priv);
2018 priv->start_calib = 1;
2022 /*****************************************************************************
2024 * mac80211 entry point functions
2026 *****************************************************************************/
2028 #define UCODE_READY_TIMEOUT (4 * HZ)
2030 static int iwl_mac_start(struct ieee80211_hw *hw)
2032 struct iwl_priv *priv = hw->priv;
2035 IWL_DEBUG_MAC80211(priv, "enter\n");
2037 /* we should be verifying the device is ready to be opened */
2038 mutex_lock(&priv->mutex);
2040 memset(&priv->staging_rxon, 0, sizeof(struct iwl_rxon_cmd));
2041 /* fetch ucode file from disk, alloc and copy to bus-master buffers ...
2042 * ucode filename and max sizes are card-specific. */
2044 if (!priv->ucode_code.len) {
2045 ret = iwl_read_ucode(priv);
2047 IWL_ERR(priv, "Could not read microcode: %d\n", ret);
2048 mutex_unlock(&priv->mutex);
2053 ret = __iwl_up(priv);
2055 mutex_unlock(&priv->mutex);
2057 iwl_rfkill_set_hw_state(priv);
2062 if (iwl_is_rfkill(priv))
2065 IWL_DEBUG_INFO(priv, "Start UP work done.\n");
2067 if (test_bit(STATUS_IN_SUSPEND, &priv->status))
2070 /* Wait for START_ALIVE from Run Time ucode. Otherwise callbacks from
2071 * mac80211 will not be run successfully. */
2072 ret = wait_event_interruptible_timeout(priv->wait_command_queue,
2073 test_bit(STATUS_READY, &priv->status),
2074 UCODE_READY_TIMEOUT);
2076 if (!test_bit(STATUS_READY, &priv->status)) {
2077 IWL_ERR(priv, "START_ALIVE timeout after %dms.\n",
2078 jiffies_to_msecs(UCODE_READY_TIMEOUT));
2085 IWL_DEBUG_MAC80211(priv, "leave\n");
2089 static void iwl_mac_stop(struct ieee80211_hw *hw)
2091 struct iwl_priv *priv = hw->priv;
2093 IWL_DEBUG_MAC80211(priv, "enter\n");
2095 if (!priv->is_open) {
2096 IWL_DEBUG_MAC80211(priv, "leave - skip\n");
2102 if (iwl_is_ready_rf(priv)) {
2103 /* stop mac, cancel any scan request and clear
2104 * RXON_FILTER_ASSOC_MSK BIT
2106 mutex_lock(&priv->mutex);
2107 iwl_scan_cancel_timeout(priv, 100);
2108 mutex_unlock(&priv->mutex);
2113 flush_workqueue(priv->workqueue);
2115 /* enable interrupts again in order to receive rfkill changes */
2116 iwl_write32(priv, CSR_INT, 0xFFFFFFFF);
2117 iwl_enable_interrupts(priv);
2119 IWL_DEBUG_MAC80211(priv, "leave\n");
2122 static int iwl_mac_tx(struct ieee80211_hw *hw, struct sk_buff *skb)
2124 struct iwl_priv *priv = hw->priv;
2126 IWL_DEBUG_MACDUMP(priv, "enter\n");
2128 IWL_DEBUG_TX(priv, "dev->xmit(%d bytes) at rate 0x%02x\n", skb->len,
2129 ieee80211_get_tx_rate(hw, IEEE80211_SKB_CB(skb))->bitrate);
2131 if (iwl_tx_skb(priv, skb))
2132 dev_kfree_skb_any(skb);
2134 IWL_DEBUG_MACDUMP(priv, "leave\n");
2135 return NETDEV_TX_OK;
2138 static int iwl_mac_add_interface(struct ieee80211_hw *hw,
2139 struct ieee80211_if_init_conf *conf)
2141 struct iwl_priv *priv = hw->priv;
2142 unsigned long flags;
2144 IWL_DEBUG_MAC80211(priv, "enter: type %d\n", conf->type);
2147 IWL_DEBUG_MAC80211(priv, "leave - vif != NULL\n");
2151 spin_lock_irqsave(&priv->lock, flags);
2152 priv->vif = conf->vif;
2153 priv->iw_mode = conf->type;
2155 spin_unlock_irqrestore(&priv->lock, flags);
2157 mutex_lock(&priv->mutex);
2159 if (conf->mac_addr) {
2160 IWL_DEBUG_MAC80211(priv, "Set %pM\n", conf->mac_addr);
2161 memcpy(priv->mac_addr, conf->mac_addr, ETH_ALEN);
2164 if (iwl_set_mode(priv, conf->type) == -EAGAIN)
2165 /* we are not ready, will run again when ready */
2166 set_bit(STATUS_MODE_PENDING, &priv->status);
2168 mutex_unlock(&priv->mutex);
2170 IWL_DEBUG_MAC80211(priv, "leave\n");
2175 * iwl_mac_config - mac80211 config callback
2177 * We ignore conf->flags & IEEE80211_CONF_SHORT_SLOT_TIME since it seems to
2178 * be set inappropriately and the driver currently sets the hardware up to
2179 * use it whenever needed.
2181 static int iwl_mac_config(struct ieee80211_hw *hw, u32 changed)
2183 struct iwl_priv *priv = hw->priv;
2184 const struct iwl_channel_info *ch_info;
2185 struct ieee80211_conf *conf = &hw->conf;
2186 unsigned long flags = 0;
2189 int scan_active = 0;
2191 mutex_lock(&priv->mutex);
2192 IWL_DEBUG_MAC80211(priv, "enter to channel %d changed 0x%X\n",
2193 conf->channel->hw_value, changed);
2195 if (unlikely(!priv->cfg->mod_params->disable_hw_scan &&
2196 test_bit(STATUS_SCANNING, &priv->status))) {
2198 IWL_DEBUG_MAC80211(priv, "leave - scanning\n");
2202 /* during scanning mac80211 will delay channel setting until
2203 * scan finish with changed = 0
2205 if (!changed || (changed & IEEE80211_CONF_CHANGE_CHANNEL)) {
2209 ch = ieee80211_frequency_to_channel(conf->channel->center_freq);
2210 ch_info = iwl_get_channel_info(priv, conf->channel->band, ch);
2211 if (!is_channel_valid(ch_info)) {
2212 IWL_DEBUG_MAC80211(priv, "leave - invalid channel\n");
2217 if (priv->iw_mode == NL80211_IFTYPE_ADHOC &&
2218 !is_channel_ibss(ch_info)) {
2219 IWL_ERR(priv, "channel %d in band %d not "
2221 conf->channel->hw_value, conf->channel->band);
2226 priv->current_ht_config.is_ht = conf_is_ht(conf);
2228 spin_lock_irqsave(&priv->lock, flags);
2231 /* if we are switching from ht to 2.4 clear flags
2232 * from any ht related info since 2.4 does not
2234 if ((le16_to_cpu(priv->staging_rxon.channel) != ch))
2235 priv->staging_rxon.flags = 0;
2237 iwl_set_rxon_channel(priv, conf->channel);
2239 iwl_set_flags_for_band(priv, conf->channel->band);
2240 spin_unlock_irqrestore(&priv->lock, flags);
2242 /* The list of supported rates and rate mask can be different
2243 * for each band; since the band may have changed, reset
2244 * the rate mask to what mac80211 lists */
2248 if (changed & IEEE80211_CONF_CHANGE_PS) {
2249 if (conf->flags & IEEE80211_CONF_PS)
2250 ret = iwl_power_set_user_mode(priv, IWL_POWER_INDEX_3);
2252 ret = iwl_power_set_user_mode(priv, IWL_POWER_MODE_CAM);
2254 IWL_DEBUG_MAC80211(priv, "Error setting power level\n");
2258 if (changed & IEEE80211_CONF_CHANGE_POWER) {
2259 IWL_DEBUG_MAC80211(priv, "TX Power old=%d new=%d\n",
2260 priv->tx_power_user_lmt, conf->power_level);
2262 iwl_set_tx_power(priv, conf->power_level, false);
2265 /* call to ensure that 4965 rx_chain is set properly in monitor mode */
2266 iwl_set_rxon_chain(priv);
2268 if (changed & IEEE80211_CONF_CHANGE_RADIO_ENABLED) {
2269 if (conf->radio_enabled &&
2270 iwl_radio_kill_sw_enable_radio(priv)) {
2271 IWL_DEBUG_MAC80211(priv, "leave - RF-KILL - "
2272 "waiting for uCode\n");
2276 if (!conf->radio_enabled)
2277 iwl_radio_kill_sw_disable_radio(priv);
2280 if (!conf->radio_enabled) {
2281 IWL_DEBUG_MAC80211(priv, "leave - radio disabled\n");
2285 if (!iwl_is_ready(priv)) {
2286 IWL_DEBUG_MAC80211(priv, "leave - not ready\n");
2293 if (memcmp(&priv->active_rxon,
2294 &priv->staging_rxon, sizeof(priv->staging_rxon)))
2295 iwl_commit_rxon(priv);
2297 IWL_DEBUG_INFO(priv, "No re-sending same RXON configuration.\n");
2301 IWL_DEBUG_MAC80211(priv, "leave\n");
2302 mutex_unlock(&priv->mutex);
2306 static void iwl_config_ap(struct iwl_priv *priv)
2309 unsigned long flags;
2311 if (test_bit(STATUS_EXIT_PENDING, &priv->status))
2314 /* The following should be done only at AP bring up */
2315 if (!iwl_is_associated(priv)) {
2317 /* RXON - unassoc (to set timing command) */
2318 priv->staging_rxon.filter_flags &= ~RXON_FILTER_ASSOC_MSK;
2319 iwl_commit_rxon(priv);
2322 iwl_setup_rxon_timing(priv);
2323 ret = iwl_send_cmd_pdu(priv, REPLY_RXON_TIMING,
2324 sizeof(priv->rxon_timing), &priv->rxon_timing);
2326 IWL_WARN(priv, "REPLY_RXON_TIMING failed - "
2327 "Attempting to continue.\n");
2329 iwl_set_rxon_chain(priv);
2331 /* FIXME: what should be the assoc_id for AP? */
2332 priv->staging_rxon.assoc_id = cpu_to_le16(priv->assoc_id);
2333 if (priv->assoc_capability & WLAN_CAPABILITY_SHORT_PREAMBLE)
2334 priv->staging_rxon.flags |=
2335 RXON_FLG_SHORT_PREAMBLE_MSK;
2337 priv->staging_rxon.flags &=
2338 ~RXON_FLG_SHORT_PREAMBLE_MSK;
2340 if (priv->staging_rxon.flags & RXON_FLG_BAND_24G_MSK) {
2341 if (priv->assoc_capability &
2342 WLAN_CAPABILITY_SHORT_SLOT_TIME)
2343 priv->staging_rxon.flags |=
2344 RXON_FLG_SHORT_SLOT_MSK;
2346 priv->staging_rxon.flags &=
2347 ~RXON_FLG_SHORT_SLOT_MSK;
2349 if (priv->iw_mode == NL80211_IFTYPE_ADHOC)
2350 priv->staging_rxon.flags &=
2351 ~RXON_FLG_SHORT_SLOT_MSK;
2353 /* restore RXON assoc */
2354 priv->staging_rxon.filter_flags |= RXON_FILTER_ASSOC_MSK;
2355 iwl_commit_rxon(priv);
2356 spin_lock_irqsave(&priv->lock, flags);
2357 iwl_activate_qos(priv, 1);
2358 spin_unlock_irqrestore(&priv->lock, flags);
2359 iwl_rxon_add_station(priv, iwl_bcast_addr, 0);
2361 iwl_send_beacon_cmd(priv);
2363 /* FIXME - we need to add code here to detect a totally new
2364 * configuration, reset the AP, unassoc, rxon timing, assoc,
2365 * clear sta table, add BCAST sta... */
2369 static int iwl_mac_config_interface(struct ieee80211_hw *hw,
2370 struct ieee80211_vif *vif,
2371 struct ieee80211_if_conf *conf)
2373 struct iwl_priv *priv = hw->priv;
2379 if (priv->vif != vif) {
2380 IWL_DEBUG_MAC80211(priv, "leave - priv->vif != vif\n");
2384 if (priv->iw_mode == NL80211_IFTYPE_ADHOC &&
2385 conf->changed & IEEE80211_IFCC_BEACON) {
2386 struct sk_buff *beacon = ieee80211_beacon_get(hw, vif);
2389 mutex_lock(&priv->mutex);
2390 rc = iwl_mac_beacon_update(hw, beacon);
2391 mutex_unlock(&priv->mutex);
2396 if (!iwl_is_alive(priv))
2399 mutex_lock(&priv->mutex);
2402 IWL_DEBUG_MAC80211(priv, "bssid: %pM\n", conf->bssid);
2405 * very dubious code was here; the probe filtering flag is never set:
2407 if (unlikely(test_bit(STATUS_SCANNING, &priv->status)) &&
2408 !(priv->hw->flags & IEEE80211_HW_NO_PROBE_FILTERING)) {
2411 if (priv->iw_mode == NL80211_IFTYPE_AP) {
2413 conf->bssid = priv->mac_addr;
2414 memcpy(priv->bssid, priv->mac_addr, ETH_ALEN);
2415 IWL_DEBUG_MAC80211(priv, "bssid was set to: %pM\n",
2418 if (priv->ibss_beacon)
2419 dev_kfree_skb(priv->ibss_beacon);
2421 priv->ibss_beacon = ieee80211_beacon_get(hw, vif);
2424 if (iwl_is_rfkill(priv))
2427 if (conf->bssid && !is_zero_ether_addr(conf->bssid) &&
2428 !is_multicast_ether_addr(conf->bssid)) {
2429 /* If there is currently a HW scan going on in the background
2430 * then we need to cancel it else the RXON below will fail. */
2431 if (iwl_scan_cancel_timeout(priv, 100)) {
2432 IWL_WARN(priv, "Aborted scan still in progress "
2434 IWL_DEBUG_MAC80211(priv, "leaving - scan abort failed.\n");
2435 mutex_unlock(&priv->mutex);
2438 memcpy(priv->staging_rxon.bssid_addr, conf->bssid, ETH_ALEN);
2440 /* TODO: Audit driver for usage of these members and see
2441 * if mac80211 deprecates them (priv->bssid looks like it
2442 * shouldn't be there, but I haven't scanned the IBSS code
2443 * to verify) - jpk */
2444 memcpy(priv->bssid, conf->bssid, ETH_ALEN);
2446 if (priv->iw_mode == NL80211_IFTYPE_AP)
2447 iwl_config_ap(priv);
2449 rc = iwl_commit_rxon(priv);
2450 if ((priv->iw_mode == NL80211_IFTYPE_STATION) && rc)
2451 iwl_rxon_add_station(
2452 priv, priv->active_rxon.bssid_addr, 1);
2456 iwl_scan_cancel_timeout(priv, 100);
2457 priv->staging_rxon.filter_flags &= ~RXON_FILTER_ASSOC_MSK;
2458 iwl_commit_rxon(priv);
2462 IWL_DEBUG_MAC80211(priv, "leave\n");
2463 mutex_unlock(&priv->mutex);
2468 static void iwl_mac_remove_interface(struct ieee80211_hw *hw,
2469 struct ieee80211_if_init_conf *conf)
2471 struct iwl_priv *priv = hw->priv;
2473 IWL_DEBUG_MAC80211(priv, "enter\n");
2475 mutex_lock(&priv->mutex);
2477 if (iwl_is_ready_rf(priv)) {
2478 iwl_scan_cancel_timeout(priv, 100);
2479 priv->staging_rxon.filter_flags &= ~RXON_FILTER_ASSOC_MSK;
2480 iwl_commit_rxon(priv);
2482 if (priv->vif == conf->vif) {
2484 memset(priv->bssid, 0, ETH_ALEN);
2486 mutex_unlock(&priv->mutex);
2488 IWL_DEBUG_MAC80211(priv, "leave\n");
2492 #define IWL_DELAY_NEXT_SCAN_AFTER_ASSOC (HZ*6)
2493 static void iwl_bss_info_changed(struct ieee80211_hw *hw,
2494 struct ieee80211_vif *vif,
2495 struct ieee80211_bss_conf *bss_conf,
2498 struct iwl_priv *priv = hw->priv;
2500 IWL_DEBUG_MAC80211(priv, "changes = 0x%X\n", changes);
2502 if (changes & BSS_CHANGED_ERP_PREAMBLE) {
2503 IWL_DEBUG_MAC80211(priv, "ERP_PREAMBLE %d\n",
2504 bss_conf->use_short_preamble);
2505 if (bss_conf->use_short_preamble)
2506 priv->staging_rxon.flags |= RXON_FLG_SHORT_PREAMBLE_MSK;
2508 priv->staging_rxon.flags &= ~RXON_FLG_SHORT_PREAMBLE_MSK;
2511 if (changes & BSS_CHANGED_ERP_CTS_PROT) {
2512 IWL_DEBUG_MAC80211(priv, "ERP_CTS %d\n", bss_conf->use_cts_prot);
2513 if (bss_conf->use_cts_prot && (priv->band != IEEE80211_BAND_5GHZ))
2514 priv->staging_rxon.flags |= RXON_FLG_TGG_PROTECT_MSK;
2516 priv->staging_rxon.flags &= ~RXON_FLG_TGG_PROTECT_MSK;
2519 if (changes & BSS_CHANGED_HT) {
2520 iwl_ht_conf(priv, bss_conf);
2521 iwl_set_rxon_chain(priv);
2524 if (changes & BSS_CHANGED_ASSOC) {
2525 IWL_DEBUG_MAC80211(priv, "ASSOC %d\n", bss_conf->assoc);
2526 /* This should never happen as this function should
2527 * never be called from interrupt context. */
2528 if (WARN_ON_ONCE(in_interrupt()))
2530 if (bss_conf->assoc) {
2531 priv->assoc_id = bss_conf->aid;
2532 priv->beacon_int = bss_conf->beacon_int;
2533 priv->power_data.dtim_period = bss_conf->dtim_period;
2534 priv->timestamp = bss_conf->timestamp;
2535 priv->assoc_capability = bss_conf->assoc_capability;
2537 /* we have just associated, don't start scan too early
2538 * leave time for EAPOL exchange to complete
2540 priv->next_scan_jiffies = jiffies +
2541 IWL_DELAY_NEXT_SCAN_AFTER_ASSOC;
2542 mutex_lock(&priv->mutex);
2543 iwl_post_associate(priv);
2544 mutex_unlock(&priv->mutex);
2547 IWL_DEBUG_MAC80211(priv, "DISASSOC %d\n", bss_conf->assoc);
2549 } else if (changes && iwl_is_associated(priv) && priv->assoc_id) {
2550 IWL_DEBUG_MAC80211(priv, "Associated Changes %d\n", changes);
2551 iwl_send_rxon_assoc(priv);
2556 static void iwl_mac_update_tkip_key(struct ieee80211_hw *hw,
2557 struct ieee80211_key_conf *keyconf, const u8 *addr,
2558 u32 iv32, u16 *phase1key)
2561 struct iwl_priv *priv = hw->priv;
2562 IWL_DEBUG_MAC80211(priv, "enter\n");
2564 iwl_update_tkip_key(priv, keyconf, addr, iv32, phase1key);
2566 IWL_DEBUG_MAC80211(priv, "leave\n");
2569 static int iwl_mac_set_key(struct ieee80211_hw *hw, enum set_key_cmd cmd,
2570 struct ieee80211_vif *vif,
2571 struct ieee80211_sta *sta,
2572 struct ieee80211_key_conf *key)
2574 struct iwl_priv *priv = hw->priv;
2578 bool is_default_wep_key = false;
2580 IWL_DEBUG_MAC80211(priv, "enter\n");
2582 if (priv->hw_params.sw_crypto) {
2583 IWL_DEBUG_MAC80211(priv, "leave - hwcrypto disabled\n");
2586 addr = sta ? sta->addr : iwl_bcast_addr;
2587 sta_id = iwl_find_station(priv, addr);
2588 if (sta_id == IWL_INVALID_STATION) {
2589 IWL_DEBUG_MAC80211(priv, "leave - %pM not in station map.\n",
2595 mutex_lock(&priv->mutex);
2596 iwl_scan_cancel_timeout(priv, 100);
2597 mutex_unlock(&priv->mutex);
2599 /* If we are getting WEP group key and we didn't receive any key mapping
2600 * so far, we are in legacy wep mode (group key only), otherwise we are
2602 * In legacy wep mode, we use another host command to the uCode */
2603 if (key->alg == ALG_WEP && sta_id == priv->hw_params.bcast_sta_id &&
2604 priv->iw_mode != NL80211_IFTYPE_AP) {
2606 is_default_wep_key = !priv->key_mapping_key;
2608 is_default_wep_key =
2609 (key->hw_key_idx == HW_KEY_DEFAULT);
2614 if (is_default_wep_key)
2615 ret = iwl_set_default_wep_key(priv, key);
2617 ret = iwl_set_dynamic_key(priv, key, sta_id);
2619 IWL_DEBUG_MAC80211(priv, "enable hwcrypto key\n");
2622 if (is_default_wep_key)
2623 ret = iwl_remove_default_wep_key(priv, key);
2625 ret = iwl_remove_dynamic_key(priv, key, sta_id);
2627 IWL_DEBUG_MAC80211(priv, "disable hwcrypto key\n");
2633 IWL_DEBUG_MAC80211(priv, "leave\n");
2638 static int iwl_mac_conf_tx(struct ieee80211_hw *hw, u16 queue,
2639 const struct ieee80211_tx_queue_params *params)
2641 struct iwl_priv *priv = hw->priv;
2642 unsigned long flags;
2645 IWL_DEBUG_MAC80211(priv, "enter\n");
2647 if (!iwl_is_ready_rf(priv)) {
2648 IWL_DEBUG_MAC80211(priv, "leave - RF not ready\n");
2652 if (queue >= AC_NUM) {
2653 IWL_DEBUG_MAC80211(priv, "leave - queue >= AC_NUM %d\n", queue);
2657 q = AC_NUM - 1 - queue;
2659 spin_lock_irqsave(&priv->lock, flags);
2661 priv->qos_data.def_qos_parm.ac[q].cw_min = cpu_to_le16(params->cw_min);
2662 priv->qos_data.def_qos_parm.ac[q].cw_max = cpu_to_le16(params->cw_max);
2663 priv->qos_data.def_qos_parm.ac[q].aifsn = params->aifs;
2664 priv->qos_data.def_qos_parm.ac[q].edca_txop =
2665 cpu_to_le16((params->txop * 32));
2667 priv->qos_data.def_qos_parm.ac[q].reserved1 = 0;
2668 priv->qos_data.qos_active = 1;
2670 if (priv->iw_mode == NL80211_IFTYPE_AP)
2671 iwl_activate_qos(priv, 1);
2672 else if (priv->assoc_id && iwl_is_associated(priv))
2673 iwl_activate_qos(priv, 0);
2675 spin_unlock_irqrestore(&priv->lock, flags);
2677 IWL_DEBUG_MAC80211(priv, "leave\n");
2681 static int iwl_mac_ampdu_action(struct ieee80211_hw *hw,
2682 enum ieee80211_ampdu_mlme_action action,
2683 struct ieee80211_sta *sta, u16 tid, u16 *ssn)
2685 struct iwl_priv *priv = hw->priv;
2688 IWL_DEBUG_HT(priv, "A-MPDU action on addr %pM tid %d\n",
2691 if (!(priv->cfg->sku & IWL_SKU_N))
2695 case IEEE80211_AMPDU_RX_START:
2696 IWL_DEBUG_HT(priv, "start Rx\n");
2697 return iwl_sta_rx_agg_start(priv, sta->addr, tid, *ssn);
2698 case IEEE80211_AMPDU_RX_STOP:
2699 IWL_DEBUG_HT(priv, "stop Rx\n");
2700 ret = iwl_sta_rx_agg_stop(priv, sta->addr, tid);
2701 if (test_bit(STATUS_EXIT_PENDING, &priv->status))
2705 case IEEE80211_AMPDU_TX_START:
2706 IWL_DEBUG_HT(priv, "start Tx\n");
2707 return iwl_tx_agg_start(priv, sta->addr, tid, ssn);
2708 case IEEE80211_AMPDU_TX_STOP:
2709 IWL_DEBUG_HT(priv, "stop Tx\n");
2710 ret = iwl_tx_agg_stop(priv, sta->addr, tid);
2711 if (test_bit(STATUS_EXIT_PENDING, &priv->status))
2716 IWL_DEBUG_HT(priv, "unknown\n");
2723 static int iwl_mac_get_tx_stats(struct ieee80211_hw *hw,
2724 struct ieee80211_tx_queue_stats *stats)
2726 struct iwl_priv *priv = hw->priv;
2728 struct iwl_tx_queue *txq;
2729 struct iwl_queue *q;
2730 unsigned long flags;
2732 IWL_DEBUG_MAC80211(priv, "enter\n");
2734 if (!iwl_is_ready_rf(priv)) {
2735 IWL_DEBUG_MAC80211(priv, "leave - RF not ready\n");
2739 spin_lock_irqsave(&priv->lock, flags);
2741 for (i = 0; i < AC_NUM; i++) {
2742 txq = &priv->txq[i];
2744 avail = iwl_queue_space(q);
2746 stats[i].len = q->n_window - avail;
2747 stats[i].limit = q->n_window - q->high_mark;
2748 stats[i].count = q->n_window;
2751 spin_unlock_irqrestore(&priv->lock, flags);
2753 IWL_DEBUG_MAC80211(priv, "leave\n");
2758 static int iwl_mac_get_stats(struct ieee80211_hw *hw,
2759 struct ieee80211_low_level_stats *stats)
2761 struct iwl_priv *priv = hw->priv;
2764 IWL_DEBUG_MAC80211(priv, "enter\n");
2765 IWL_DEBUG_MAC80211(priv, "leave\n");
2770 static void iwl_mac_reset_tsf(struct ieee80211_hw *hw)
2772 struct iwl_priv *priv = hw->priv;
2773 unsigned long flags;
2775 mutex_lock(&priv->mutex);
2776 IWL_DEBUG_MAC80211(priv, "enter\n");
2778 spin_lock_irqsave(&priv->lock, flags);
2779 memset(&priv->current_ht_config, 0, sizeof(struct iwl_ht_info));
2780 spin_unlock_irqrestore(&priv->lock, flags);
2782 iwl_reset_qos(priv);
2784 spin_lock_irqsave(&priv->lock, flags);
2786 priv->assoc_capability = 0;
2787 priv->assoc_station_added = 0;
2789 /* new association get rid of ibss beacon skb */
2790 if (priv->ibss_beacon)
2791 dev_kfree_skb(priv->ibss_beacon);
2793 priv->ibss_beacon = NULL;
2795 priv->beacon_int = priv->hw->conf.beacon_int;
2796 priv->timestamp = 0;
2797 if ((priv->iw_mode == NL80211_IFTYPE_STATION))
2798 priv->beacon_int = 0;
2800 spin_unlock_irqrestore(&priv->lock, flags);
2802 if (!iwl_is_ready_rf(priv)) {
2803 IWL_DEBUG_MAC80211(priv, "leave - not ready\n");
2804 mutex_unlock(&priv->mutex);
2808 /* we are restarting association process
2809 * clear RXON_FILTER_ASSOC_MSK bit
2811 if (priv->iw_mode != NL80211_IFTYPE_AP) {
2812 iwl_scan_cancel_timeout(priv, 100);
2813 priv->staging_rxon.filter_flags &= ~RXON_FILTER_ASSOC_MSK;
2814 iwl_commit_rxon(priv);
2817 iwl_power_update_mode(priv, 0);
2819 /* Per mac80211.h: This is only used in IBSS mode... */
2820 if (priv->iw_mode != NL80211_IFTYPE_ADHOC) {
2822 /* switch to CAM during association period.
2823 * the ucode will block any association/authentication
2824 * frome during assiciation period if it can not hear
2825 * the AP because of PM. the timer enable PM back is
2826 * association do not complete
2828 if (priv->hw->conf.channel->flags & (IEEE80211_CHAN_PASSIVE_SCAN |
2829 IEEE80211_CHAN_RADAR))
2830 iwl_power_disable_management(priv, 3000);
2832 IWL_DEBUG_MAC80211(priv, "leave - not in IBSS\n");
2833 mutex_unlock(&priv->mutex);
2839 mutex_unlock(&priv->mutex);
2841 IWL_DEBUG_MAC80211(priv, "leave\n");
2844 static int iwl_mac_beacon_update(struct ieee80211_hw *hw, struct sk_buff *skb)
2846 struct iwl_priv *priv = hw->priv;
2847 unsigned long flags;
2850 IWL_DEBUG_MAC80211(priv, "enter\n");
2852 if (!iwl_is_ready_rf(priv)) {
2853 IWL_DEBUG_MAC80211(priv, "leave - RF not ready\n");
2857 if (priv->iw_mode != NL80211_IFTYPE_ADHOC) {
2858 IWL_DEBUG_MAC80211(priv, "leave - not IBSS\n");
2862 spin_lock_irqsave(&priv->lock, flags);
2864 if (priv->ibss_beacon)
2865 dev_kfree_skb(priv->ibss_beacon);
2867 priv->ibss_beacon = skb;
2870 timestamp = ((struct ieee80211_mgmt *)skb->data)->u.beacon.timestamp;
2871 priv->timestamp = le64_to_cpu(timestamp);
2873 IWL_DEBUG_MAC80211(priv, "leave\n");
2874 spin_unlock_irqrestore(&priv->lock, flags);
2876 iwl_reset_qos(priv);
2878 iwl_post_associate(priv);
2884 /*****************************************************************************
2888 *****************************************************************************/
2890 #ifdef CONFIG_IWLWIFI_DEBUG
2893 * The following adds a new attribute to the sysfs representation
2894 * of this device driver (i.e. a new file in /sys/class/net/wlan0/device/)
2895 * used for controlling the debug level.
2897 * See the level definitions in iwl for details.
2900 static ssize_t show_debug_level(struct device *d,
2901 struct device_attribute *attr, char *buf)
2903 struct iwl_priv *priv = d->driver_data;
2905 return sprintf(buf, "0x%08X\n", priv->debug_level);
2907 static ssize_t store_debug_level(struct device *d,
2908 struct device_attribute *attr,
2909 const char *buf, size_t count)
2911 struct iwl_priv *priv = d->driver_data;
2915 ret = strict_strtoul(buf, 0, &val);
2917 IWL_ERR(priv, "%s is not in hex or decimal form.\n", buf);
2919 priv->debug_level = val;
2921 return strnlen(buf, count);
2924 static DEVICE_ATTR(debug_level, S_IWUSR | S_IRUGO,
2925 show_debug_level, store_debug_level);
2928 #endif /* CONFIG_IWLWIFI_DEBUG */
2931 static ssize_t show_version(struct device *d,
2932 struct device_attribute *attr, char *buf)
2934 struct iwl_priv *priv = d->driver_data;
2935 struct iwl_alive_resp *palive = &priv->card_alive;
2939 if (palive->is_valid)
2940 pos += sprintf(buf + pos,
2941 "fw version: 0x%01X.0x%01X.0x%01X.0x%01X\n"
2942 "fw type: 0x%01X 0x%01X\n",
2943 palive->ucode_major, palive->ucode_minor,
2944 palive->sw_rev[0], palive->sw_rev[1],
2945 palive->ver_type, palive->ver_subtype);
2947 pos += sprintf(buf + pos, "fw not loaded\n");
2950 eeprom_ver = iwl_eeprom_query16(priv, EEPROM_VERSION);
2951 pos += sprintf(buf + pos, "EEPROM version: 0x%x\n",
2954 pos += sprintf(buf + pos, "EEPROM not initialzed\n");
2960 static DEVICE_ATTR(version, S_IWUSR | S_IRUGO, show_version, NULL);
2962 static ssize_t show_temperature(struct device *d,
2963 struct device_attribute *attr, char *buf)
2965 struct iwl_priv *priv = (struct iwl_priv *)d->driver_data;
2967 if (!iwl_is_alive(priv))
2970 return sprintf(buf, "%d\n", priv->temperature);
2973 static DEVICE_ATTR(temperature, S_IRUGO, show_temperature, NULL);
2975 static ssize_t show_tx_power(struct device *d,
2976 struct device_attribute *attr, char *buf)
2978 struct iwl_priv *priv = (struct iwl_priv *)d->driver_data;
2980 if (!iwl_is_ready_rf(priv))
2981 return sprintf(buf, "off\n");
2983 return sprintf(buf, "%d\n", priv->tx_power_user_lmt);
2986 static ssize_t store_tx_power(struct device *d,
2987 struct device_attribute *attr,
2988 const char *buf, size_t count)
2990 struct iwl_priv *priv = (struct iwl_priv *)d->driver_data;
2994 ret = strict_strtoul(buf, 10, &val);
2996 IWL_INFO(priv, "%s is not in decimal form.\n", buf);
2998 iwl_set_tx_power(priv, val, false);
3003 static DEVICE_ATTR(tx_power, S_IWUSR | S_IRUGO, show_tx_power, store_tx_power);
3005 static ssize_t show_flags(struct device *d,
3006 struct device_attribute *attr, char *buf)
3008 struct iwl_priv *priv = (struct iwl_priv *)d->driver_data;
3010 return sprintf(buf, "0x%04X\n", priv->active_rxon.flags);
3013 static ssize_t store_flags(struct device *d,
3014 struct device_attribute *attr,
3015 const char *buf, size_t count)
3017 struct iwl_priv *priv = (struct iwl_priv *)d->driver_data;
3020 int ret = strict_strtoul(buf, 0, &val);
3025 mutex_lock(&priv->mutex);
3026 if (le32_to_cpu(priv->staging_rxon.flags) != flags) {
3027 /* Cancel any currently running scans... */
3028 if (iwl_scan_cancel_timeout(priv, 100))
3029 IWL_WARN(priv, "Could not cancel scan.\n");
3031 IWL_DEBUG_INFO(priv, "Commit rxon.flags = 0x%04X\n", flags);
3032 priv->staging_rxon.flags = cpu_to_le32(flags);
3033 iwl_commit_rxon(priv);
3036 mutex_unlock(&priv->mutex);
3041 static DEVICE_ATTR(flags, S_IWUSR | S_IRUGO, show_flags, store_flags);
3043 static ssize_t show_filter_flags(struct device *d,
3044 struct device_attribute *attr, char *buf)
3046 struct iwl_priv *priv = (struct iwl_priv *)d->driver_data;
3048 return sprintf(buf, "0x%04X\n",
3049 le32_to_cpu(priv->active_rxon.filter_flags));
3052 static ssize_t store_filter_flags(struct device *d,
3053 struct device_attribute *attr,
3054 const char *buf, size_t count)
3056 struct iwl_priv *priv = (struct iwl_priv *)d->driver_data;
3059 int ret = strict_strtoul(buf, 0, &val);
3062 filter_flags = (u32)val;
3064 mutex_lock(&priv->mutex);
3065 if (le32_to_cpu(priv->staging_rxon.filter_flags) != filter_flags) {
3066 /* Cancel any currently running scans... */
3067 if (iwl_scan_cancel_timeout(priv, 100))
3068 IWL_WARN(priv, "Could not cancel scan.\n");
3070 IWL_DEBUG_INFO(priv, "Committing rxon.filter_flags = "
3071 "0x%04X\n", filter_flags);
3072 priv->staging_rxon.filter_flags =
3073 cpu_to_le32(filter_flags);
3074 iwl_commit_rxon(priv);
3077 mutex_unlock(&priv->mutex);
3082 static DEVICE_ATTR(filter_flags, S_IWUSR | S_IRUGO, show_filter_flags,
3083 store_filter_flags);
3085 static ssize_t store_power_level(struct device *d,
3086 struct device_attribute *attr,
3087 const char *buf, size_t count)
3089 struct iwl_priv *priv = dev_get_drvdata(d);
3094 mutex_lock(&priv->mutex);
3096 ret = strict_strtoul(buf, 10, &mode);
3100 ret = iwl_power_set_user_mode(priv, mode);
3102 IWL_DEBUG_MAC80211(priv, "failed setting power mode.\n");
3108 mutex_unlock(&priv->mutex);
3112 static ssize_t show_power_level(struct device *d,
3113 struct device_attribute *attr, char *buf)
3115 struct iwl_priv *priv = dev_get_drvdata(d);
3116 int mode = priv->power_data.user_power_setting;
3117 int system = priv->power_data.system_power_setting;
3118 int level = priv->power_data.power_mode;
3122 case IWL_POWER_SYS_AUTO:
3123 p += sprintf(p, "SYSTEM:auto");
3125 case IWL_POWER_SYS_AC:
3126 p += sprintf(p, "SYSTEM:ac");
3128 case IWL_POWER_SYS_BATTERY:
3129 p += sprintf(p, "SYSTEM:battery");
3133 p += sprintf(p, "\tMODE:%s", (mode < IWL_POWER_AUTO) ?
3135 p += sprintf(p, "\tINDEX:%d", level);
3136 p += sprintf(p, "\n");
3140 static DEVICE_ATTR(power_level, S_IWUSR | S_IRUSR, show_power_level,
3144 static ssize_t show_statistics(struct device *d,
3145 struct device_attribute *attr, char *buf)
3147 struct iwl_priv *priv = dev_get_drvdata(d);
3148 u32 size = sizeof(struct iwl_notif_statistics);
3149 u32 len = 0, ofs = 0;
3150 u8 *data = (u8 *)&priv->statistics;
3153 if (!iwl_is_alive(priv))
3156 mutex_lock(&priv->mutex);
3157 rc = iwl_send_statistics_request(priv, 0);
3158 mutex_unlock(&priv->mutex);
3162 "Error sending statistics request: 0x%08X\n", rc);
3166 while (size && (PAGE_SIZE - len)) {
3167 hex_dump_to_buffer(data + ofs, size, 16, 1, buf + len,
3168 PAGE_SIZE - len, 1);
3170 if (PAGE_SIZE - len)
3174 size -= min(size, 16U);
3180 static DEVICE_ATTR(statistics, S_IRUGO, show_statistics, NULL);
3183 /*****************************************************************************
3185 * driver setup and teardown
3187 *****************************************************************************/
3189 static void iwl_setup_deferred_work(struct iwl_priv *priv)
3191 priv->workqueue = create_singlethread_workqueue(DRV_NAME);
3193 init_waitqueue_head(&priv->wait_command_queue);
3195 INIT_WORK(&priv->up, iwl_bg_up);
3196 INIT_WORK(&priv->restart, iwl_bg_restart);
3197 INIT_WORK(&priv->rx_replenish, iwl_bg_rx_replenish);
3198 INIT_WORK(&priv->rf_kill, iwl_bg_rf_kill);
3199 INIT_WORK(&priv->beacon_update, iwl_bg_beacon_update);
3200 INIT_WORK(&priv->run_time_calib_work, iwl_bg_run_time_calib_work);
3201 INIT_DELAYED_WORK(&priv->init_alive_start, iwl_bg_init_alive_start);
3202 INIT_DELAYED_WORK(&priv->alive_start, iwl_bg_alive_start);
3204 iwl_setup_scan_deferred_work(priv);
3205 iwl_setup_power_deferred_work(priv);
3207 if (priv->cfg->ops->lib->setup_deferred_work)
3208 priv->cfg->ops->lib->setup_deferred_work(priv);
3210 init_timer(&priv->statistics_periodic);
3211 priv->statistics_periodic.data = (unsigned long)priv;
3212 priv->statistics_periodic.function = iwl_bg_statistics_periodic;
3214 tasklet_init(&priv->irq_tasklet, (void (*)(unsigned long))
3215 iwl_irq_tasklet, (unsigned long)priv);
3218 static void iwl_cancel_deferred_work(struct iwl_priv *priv)
3220 if (priv->cfg->ops->lib->cancel_deferred_work)
3221 priv->cfg->ops->lib->cancel_deferred_work(priv);
3223 cancel_delayed_work_sync(&priv->init_alive_start);
3224 cancel_delayed_work(&priv->scan_check);
3225 cancel_delayed_work_sync(&priv->set_power_save);
3226 cancel_delayed_work(&priv->alive_start);
3227 cancel_work_sync(&priv->beacon_update);
3228 del_timer_sync(&priv->statistics_periodic);
3231 static struct attribute *iwl_sysfs_entries[] = {
3232 &dev_attr_flags.attr,
3233 &dev_attr_filter_flags.attr,
3234 &dev_attr_power_level.attr,
3235 &dev_attr_statistics.attr,
3236 &dev_attr_temperature.attr,
3237 &dev_attr_tx_power.attr,
3238 #ifdef CONFIG_IWLWIFI_DEBUG
3239 &dev_attr_debug_level.attr,
3241 &dev_attr_version.attr,
3246 static struct attribute_group iwl_attribute_group = {
3247 .name = NULL, /* put in device directory */
3248 .attrs = iwl_sysfs_entries,
3251 static struct ieee80211_ops iwl_hw_ops = {
3253 .start = iwl_mac_start,
3254 .stop = iwl_mac_stop,
3255 .add_interface = iwl_mac_add_interface,
3256 .remove_interface = iwl_mac_remove_interface,
3257 .config = iwl_mac_config,
3258 .config_interface = iwl_mac_config_interface,
3259 .configure_filter = iwl_configure_filter,
3260 .set_key = iwl_mac_set_key,
3261 .update_tkip_key = iwl_mac_update_tkip_key,
3262 .get_stats = iwl_mac_get_stats,
3263 .get_tx_stats = iwl_mac_get_tx_stats,
3264 .conf_tx = iwl_mac_conf_tx,
3265 .reset_tsf = iwl_mac_reset_tsf,
3266 .bss_info_changed = iwl_bss_info_changed,
3267 .ampdu_action = iwl_mac_ampdu_action,
3268 .hw_scan = iwl_mac_hw_scan
3271 static int iwl_pci_probe(struct pci_dev *pdev, const struct pci_device_id *ent)
3274 struct iwl_priv *priv;
3275 struct ieee80211_hw *hw;
3276 struct iwl_cfg *cfg = (struct iwl_cfg *)(ent->driver_data);
3277 unsigned long flags;
3280 /************************
3281 * 1. Allocating HW data
3282 ************************/
3284 /* Disabling hardware scan means that mac80211 will perform scans
3285 * "the hard way", rather than using device's scan. */
3286 if (cfg->mod_params->disable_hw_scan) {
3287 if (cfg->mod_params->debug & IWL_DL_INFO)
3288 dev_printk(KERN_DEBUG, &(pdev->dev),
3289 "Disabling hw_scan\n");
3290 iwl_hw_ops.hw_scan = NULL;
3293 hw = iwl_alloc_all(cfg, &iwl_hw_ops);
3299 /* At this point both hw and priv are allocated. */
3301 SET_IEEE80211_DEV(hw, &pdev->dev);
3303 IWL_DEBUG_INFO(priv, "*** LOAD DRIVER ***\n");
3305 priv->pci_dev = pdev;
3307 #ifdef CONFIG_IWLWIFI_DEBUG
3308 priv->debug_level = priv->cfg->mod_params->debug;
3309 atomic_set(&priv->restrict_refcnt, 0);
3312 /**************************
3313 * 2. Initializing PCI bus
3314 **************************/
3315 if (pci_enable_device(pdev)) {
3317 goto out_ieee80211_free_hw;
3320 pci_set_master(pdev);
3322 err = pci_set_dma_mask(pdev, DMA_BIT_MASK(36));
3324 err = pci_set_consistent_dma_mask(pdev, DMA_BIT_MASK(36));
3326 err = pci_set_dma_mask(pdev, DMA_BIT_MASK(32));
3328 err = pci_set_consistent_dma_mask(pdev, DMA_BIT_MASK(32));
3329 /* both attempts failed: */
3331 IWL_WARN(priv, "No suitable DMA available.\n");
3332 goto out_pci_disable_device;
3336 err = pci_request_regions(pdev, DRV_NAME);
3338 goto out_pci_disable_device;
3340 pci_set_drvdata(pdev, priv);
3343 /***********************
3344 * 3. Read REV register
3345 ***********************/
3346 priv->hw_base = pci_iomap(pdev, 0, 0);
3347 if (!priv->hw_base) {
3349 goto out_pci_release_regions;
3352 IWL_DEBUG_INFO(priv, "pci_resource_len = 0x%08llx\n",
3353 (unsigned long long) pci_resource_len(pdev, 0));
3354 IWL_DEBUG_INFO(priv, "pci_resource_base = %p\n", priv->hw_base);
3356 iwl_hw_detect(priv);
3357 IWL_INFO(priv, "Detected Intel Wireless WiFi Link %s REV=0x%X\n",
3358 priv->cfg->name, priv->hw_rev);
3360 /* We disable the RETRY_TIMEOUT register (0x41) to keep
3361 * PCI Tx retries from interfering with C3 CPU state */
3362 pci_write_config_byte(pdev, PCI_CFG_RETRY_TIMEOUT, 0x00);
3365 err = priv->cfg->ops->lib->apm_ops.init(priv);
3367 IWL_ERR(priv, "Failed to init APMG\n");
3373 /* Read the EEPROM */
3374 err = iwl_eeprom_init(priv);
3376 IWL_ERR(priv, "Unable to init EEPROM\n");
3379 err = iwl_eeprom_check_version(priv);
3381 goto out_free_eeprom;
3383 /* extract MAC Address */
3384 iwl_eeprom_get_mac(priv, priv->mac_addr);
3385 IWL_DEBUG_INFO(priv, "MAC address: %pM\n", priv->mac_addr);
3386 SET_IEEE80211_PERM_ADDR(priv->hw, priv->mac_addr);
3388 /************************
3389 * 5. Setup HW constants
3390 ************************/
3391 if (iwl_set_hw_params(priv)) {
3392 IWL_ERR(priv, "failed to set hw parameters\n");
3393 goto out_free_eeprom;
3396 /*******************
3398 *******************/
3400 err = iwl_init_drv(priv);
3402 goto out_free_eeprom;
3403 /* At this point both hw and priv are initialized. */
3405 /**********************************
3406 * 7. Initialize module parameters
3407 **********************************/
3409 /* Disable radio (SW RF KILL) via parameter when loading driver */
3410 if (priv->cfg->mod_params->disable) {
3411 set_bit(STATUS_RF_KILL_SW, &priv->status);
3412 IWL_DEBUG_INFO(priv, "Radio disabled.\n");
3415 /********************
3417 ********************/
3418 spin_lock_irqsave(&priv->lock, flags);
3419 iwl_disable_interrupts(priv);
3420 spin_unlock_irqrestore(&priv->lock, flags);
3422 pci_enable_msi(priv->pci_dev);
3424 err = request_irq(priv->pci_dev->irq, iwl_isr, IRQF_SHARED,
3427 IWL_ERR(priv, "Error allocating IRQ %d\n", priv->pci_dev->irq);
3428 goto out_disable_msi;
3430 err = sysfs_create_group(&pdev->dev.kobj, &iwl_attribute_group);
3432 IWL_ERR(priv, "failed to create sysfs device attributes\n");
3436 iwl_setup_deferred_work(priv);
3437 iwl_setup_rx_handlers(priv);
3439 /**********************************
3440 * 9. Setup and register mac80211
3441 **********************************/
3443 /* enable interrupts if needed: hw bug w/a */
3444 pci_read_config_word(priv->pci_dev, PCI_COMMAND, &pci_cmd);
3445 if (pci_cmd & PCI_COMMAND_INTX_DISABLE) {
3446 pci_cmd &= ~PCI_COMMAND_INTX_DISABLE;
3447 pci_write_config_word(priv->pci_dev, PCI_COMMAND, pci_cmd);
3450 iwl_enable_interrupts(priv);
3452 err = iwl_setup_mac(priv);
3454 goto out_remove_sysfs;
3456 err = iwl_dbgfs_register(priv, DRV_NAME);
3458 IWL_ERR(priv, "failed to create debugfs files\n");
3460 /* If platform's RF_KILL switch is NOT set to KILL */
3461 if (iwl_read32(priv, CSR_GP_CNTRL) & CSR_GP_CNTRL_REG_FLAG_HW_RF_KILL_SW)
3462 clear_bit(STATUS_RF_KILL_HW, &priv->status);
3464 set_bit(STATUS_RF_KILL_HW, &priv->status);
3466 err = iwl_rfkill_init(priv);
3468 IWL_ERR(priv, "Unable to initialize RFKILL system. "
3469 "Ignoring error: %d\n", err);
3471 iwl_rfkill_set_hw_state(priv);
3473 iwl_power_initialize(priv);
3477 destroy_workqueue(priv->workqueue);
3478 priv->workqueue = NULL;
3479 sysfs_remove_group(&pdev->dev.kobj, &iwl_attribute_group);
3481 free_irq(priv->pci_dev->irq, priv);
3483 pci_disable_msi(priv->pci_dev);
3484 iwl_uninit_drv(priv);
3486 iwl_eeprom_free(priv);
3488 pci_iounmap(pdev, priv->hw_base);
3489 out_pci_release_regions:
3490 pci_set_drvdata(pdev, NULL);
3491 pci_release_regions(pdev);
3492 out_pci_disable_device:
3493 pci_disable_device(pdev);
3494 out_ieee80211_free_hw:
3495 ieee80211_free_hw(priv->hw);
3500 static void __devexit iwl_pci_remove(struct pci_dev *pdev)
3502 struct iwl_priv *priv = pci_get_drvdata(pdev);
3503 unsigned long flags;
3508 IWL_DEBUG_INFO(priv, "*** UNLOAD DRIVER ***\n");
3510 iwl_dbgfs_unregister(priv);
3511 sysfs_remove_group(&pdev->dev.kobj, &iwl_attribute_group);
3513 /* ieee80211_unregister_hw call wil cause iwl_mac_stop to
3514 * to be called and iwl_down since we are removing the device
3515 * we need to set STATUS_EXIT_PENDING bit.
3517 set_bit(STATUS_EXIT_PENDING, &priv->status);
3518 if (priv->mac80211_registered) {
3519 ieee80211_unregister_hw(priv->hw);
3520 priv->mac80211_registered = 0;
3525 /* make sure we flush any pending irq or
3526 * tasklet for the driver
3528 spin_lock_irqsave(&priv->lock, flags);
3529 iwl_disable_interrupts(priv);
3530 spin_unlock_irqrestore(&priv->lock, flags);
3532 iwl_synchronize_irq(priv);
3534 iwl_rfkill_unregister(priv);
3535 iwl_dealloc_ucode_pci(priv);
3538 iwl_rx_queue_free(priv, &priv->rxq);
3539 iwl_hw_txq_ctx_free(priv);
3541 iwl_clear_stations_table(priv);
3542 iwl_eeprom_free(priv);
3545 /*netif_stop_queue(dev); */
3546 flush_workqueue(priv->workqueue);
3548 /* ieee80211_unregister_hw calls iwl_mac_stop, which flushes
3549 * priv->workqueue... so we can't take down the workqueue
3551 destroy_workqueue(priv->workqueue);
3552 priv->workqueue = NULL;
3554 free_irq(priv->pci_dev->irq, priv);
3555 pci_disable_msi(priv->pci_dev);
3556 pci_iounmap(pdev, priv->hw_base);
3557 pci_release_regions(pdev);
3558 pci_disable_device(pdev);
3559 pci_set_drvdata(pdev, NULL);
3561 iwl_uninit_drv(priv);
3563 if (priv->ibss_beacon)
3564 dev_kfree_skb(priv->ibss_beacon);
3566 ieee80211_free_hw(priv->hw);
3571 static int iwl_pci_suspend(struct pci_dev *pdev, pm_message_t state)
3573 struct iwl_priv *priv = pci_get_drvdata(pdev);
3575 if (priv->is_open) {
3576 set_bit(STATUS_IN_SUSPEND, &priv->status);
3577 iwl_mac_stop(priv->hw);
3581 pci_save_state(pdev);
3582 pci_disable_device(pdev);
3583 pci_set_power_state(pdev, PCI_D3hot);
3588 static int iwl_pci_resume(struct pci_dev *pdev)
3590 struct iwl_priv *priv = pci_get_drvdata(pdev);
3593 pci_set_power_state(pdev, PCI_D0);
3594 ret = pci_enable_device(pdev);
3597 pci_restore_state(pdev);
3598 iwl_enable_interrupts(priv);
3601 iwl_mac_start(priv->hw);
3603 clear_bit(STATUS_IN_SUSPEND, &priv->status);
3607 #endif /* CONFIG_PM */
3609 /*****************************************************************************
3611 * driver and module entry point
3613 *****************************************************************************/
3615 /* Hardware specific file defines the PCI IDs table for that hardware module */
3616 static struct pci_device_id iwl_hw_card_ids[] = {
3617 #ifdef CONFIG_IWL4965
3618 {IWL_PCI_DEVICE(0x4229, PCI_ANY_ID, iwl4965_agn_cfg)},
3619 {IWL_PCI_DEVICE(0x4230, PCI_ANY_ID, iwl4965_agn_cfg)},
3620 #endif /* CONFIG_IWL4965 */
3621 #ifdef CONFIG_IWL5000
3622 {IWL_PCI_DEVICE(0x4232, 0x1205, iwl5100_bg_cfg)},
3623 {IWL_PCI_DEVICE(0x4232, 0x1305, iwl5100_bg_cfg)},
3624 {IWL_PCI_DEVICE(0x4232, 0x1206, iwl5100_abg_cfg)},
3625 {IWL_PCI_DEVICE(0x4232, 0x1306, iwl5100_abg_cfg)},
3626 {IWL_PCI_DEVICE(0x4232, 0x1326, iwl5100_abg_cfg)},
3627 {IWL_PCI_DEVICE(0x4237, 0x1216, iwl5100_abg_cfg)},
3628 {IWL_PCI_DEVICE(0x4232, PCI_ANY_ID, iwl5100_agn_cfg)},
3629 {IWL_PCI_DEVICE(0x4235, PCI_ANY_ID, iwl5300_agn_cfg)},
3630 {IWL_PCI_DEVICE(0x4236, PCI_ANY_ID, iwl5300_agn_cfg)},
3631 {IWL_PCI_DEVICE(0x4237, PCI_ANY_ID, iwl5100_agn_cfg)},
3632 /* 5350 WiFi/WiMax */
3633 {IWL_PCI_DEVICE(0x423A, 0x1001, iwl5350_agn_cfg)},
3634 {IWL_PCI_DEVICE(0x423A, 0x1021, iwl5350_agn_cfg)},
3635 {IWL_PCI_DEVICE(0x423B, 0x1011, iwl5350_agn_cfg)},
3636 /* 5150 Wifi/WiMax */
3637 {IWL_PCI_DEVICE(0x423C, PCI_ANY_ID, iwl5150_agn_cfg)},
3638 {IWL_PCI_DEVICE(0x423D, PCI_ANY_ID, iwl5150_agn_cfg)},
3639 /* 6000/6050 Series */
3640 {IWL_PCI_DEVICE(0x0082, 0x1102, iwl6000_2ag_cfg)},
3641 {IWL_PCI_DEVICE(0x0085, 0x1112, iwl6000_2ag_cfg)},
3642 {IWL_PCI_DEVICE(0x0082, 0x1122, iwl6000_2ag_cfg)},
3643 {IWL_PCI_DEVICE(0x422B, PCI_ANY_ID, iwl6000_3agn_cfg)},
3644 {IWL_PCI_DEVICE(0x4238, PCI_ANY_ID, iwl6000_3agn_cfg)},
3645 {IWL_PCI_DEVICE(0x0082, PCI_ANY_ID, iwl6000_2agn_cfg)},
3646 {IWL_PCI_DEVICE(0x0085, PCI_ANY_ID, iwl6000_3agn_cfg)},
3647 {IWL_PCI_DEVICE(0x0086, PCI_ANY_ID, iwl6050_3agn_cfg)},
3648 {IWL_PCI_DEVICE(0x0087, PCI_ANY_ID, iwl6050_2agn_cfg)},
3649 {IWL_PCI_DEVICE(0x0088, PCI_ANY_ID, iwl6050_3agn_cfg)},
3650 {IWL_PCI_DEVICE(0x0089, PCI_ANY_ID, iwl6050_2agn_cfg)},
3651 /* 1000 Series WiFi */
3652 {IWL_PCI_DEVICE(0x0083, PCI_ANY_ID, iwl1000_bgn_cfg)},
3653 {IWL_PCI_DEVICE(0x0084, PCI_ANY_ID, iwl1000_bgn_cfg)},
3654 #endif /* CONFIG_IWL5000 */
3658 MODULE_DEVICE_TABLE(pci, iwl_hw_card_ids);
3660 static struct pci_driver iwl_driver = {
3662 .id_table = iwl_hw_card_ids,
3663 .probe = iwl_pci_probe,
3664 .remove = __devexit_p(iwl_pci_remove),
3666 .suspend = iwl_pci_suspend,
3667 .resume = iwl_pci_resume,
3671 static int __init iwl_init(void)
3675 printk(KERN_INFO DRV_NAME ": " DRV_DESCRIPTION ", " DRV_VERSION "\n");
3676 printk(KERN_INFO DRV_NAME ": " DRV_COPYRIGHT "\n");
3678 ret = iwlagn_rate_control_register();
3680 printk(KERN_ERR DRV_NAME
3681 "Unable to register rate control algorithm: %d\n", ret);
3685 ret = pci_register_driver(&iwl_driver);
3687 printk(KERN_ERR DRV_NAME "Unable to initialize PCI module\n");
3688 goto error_register;
3694 iwlagn_rate_control_unregister();
3698 static void __exit iwl_exit(void)
3700 pci_unregister_driver(&iwl_driver);
3701 iwlagn_rate_control_unregister();
3704 module_exit(iwl_exit);
3705 module_init(iwl_init);