git.oblomov.eu Git - linux-2.6/blob - drivers/char/esp.c

   1 /*
   2  *  esp.c - driver for Hayes ESP serial cards
   3  *
   4  *  --- Notices from serial.c, upon which this driver is based ---
   5  *
   6  *  Copyright (C) 1991, 1992  Linus Torvalds
   7  *
   8  *  Extensively rewritten by Theodore Ts'o, 8/16/92 -- 9/14/92.  Now
   9  *  much more extensible to support other serial cards based on the
  10  *  16450/16550A UART's.  Added support for the AST FourPort and the
  11  *  Accent Async board.
  12  *
  13  *  set_serial_info fixed to set the flags, custom divisor, and uart
  14  *      type fields.  Fix suggested by Michael K. Johnson 12/12/92.
  15  *
  16  *  11/95: TIOCMIWAIT, TIOCGICOUNT by Angelo Haritsis <ah@doc.ic.ac.uk>
  17  *
  18  *  03/96: Modularised by Angelo Haritsis <ah@doc.ic.ac.uk>
  19  *
  20  *  rs_set_termios fixed to look also for changes of the input
  21  *      flags INPCK, BRKINT, PARMRK, IGNPAR and IGNBRK.
  22  *                                            Bernd Anhäupl 05/17/96.
  23  *
  24  * --- End of notices from serial.c ---
  25  *
  26  * Support for the ESP serial card by Andrew J. Robinson
  27  *     <arobinso@nyx.net> (Card detection routine taken from a patch
  28  *     by Dennis J. Boylan).  Patches to allow use with 2.1.x contributed
  29  *     by Chris Faylor.
  30  *
  31  * Most recent changes: (Andrew J. Robinson)
  32  *   Support for PIO mode.  This allows the driver to work properly with
  33  *     multiport cards.
  34  *
  35  * Arnaldo Carvalho de Melo <acme@conectiva.com.br> -
  36  * several cleanups, use module_init/module_exit, etc
  37  *
  38  * This module exports the following rs232 io functions:
  39  *
  40  *      int espserial_init(void);
  41  */
  42
  43 #include <linux/module.h>
  44 #include <linux/errno.h>
  45 #include <linux/signal.h>
  46 #include <linux/sched.h>
  47 #include <linux/interrupt.h>
  48 #include <linux/tty.h>
  49 #include <linux/tty_flip.h>
  50 #include <linux/serial.h>
  51 #include <linux/serialP.h>
  52 #include <linux/serial_reg.h>
  53 #include <linux/major.h>
  54 #include <linux/string.h>
  55 #include <linux/fcntl.h>
  56 #include <linux/ptrace.h>
  57 #include <linux/ioport.h>
  58 #include <linux/mm.h>
  59 #include <linux/init.h>
  60 #include <linux/delay.h>
  61 #include <linux/bitops.h>
  62
  63 #include <asm/system.h>
  64 #include <linux/io.h>
  65
  66 #include <asm/dma.h>
  67 #include <linux/slab.h>
  68 #include <linux/uaccess.h>
  69
  70 #include <linux/hayesesp.h>
  71
  72 #define NR_PORTS 64     /* maximum number of ports */
  73 #define NR_PRIMARY 8    /* maximum number of primary ports */
  74 #define REGION_SIZE 8   /* size of io region to request */
  75
  76 /* The following variables can be set by giving module options */
  77 static int irq[NR_PRIMARY];     /* IRQ for each base port */
  78 static unsigned int divisor[NR_PRIMARY]; /* custom divisor for each port */
  79 static unsigned int dma = ESP_DMA_CHANNEL; /* DMA channel */
  80 static unsigned int rx_trigger = ESP_RX_TRIGGER;
  81 static unsigned int tx_trigger = ESP_TX_TRIGGER;
  82 static unsigned int flow_off = ESP_FLOW_OFF;
  83 static unsigned int flow_on = ESP_FLOW_ON;
  84 static unsigned int rx_timeout = ESP_RX_TMOUT;
  85 static unsigned int pio_threshold = ESP_PIO_THRESHOLD;
  86
  87 MODULE_LICENSE("GPL");
  88
  89 module_param_array(irq, int, NULL, 0);
  90 module_param_array(divisor, uint, NULL, 0);
  91 module_param(dma, uint, 0);
  92 module_param(rx_trigger, uint, 0);
  93 module_param(tx_trigger, uint, 0);
  94 module_param(flow_off, uint, 0);
  95 module_param(flow_on, uint, 0);
  96 module_param(rx_timeout, uint, 0);
  97 module_param(pio_threshold, uint, 0);
  98
  99 /* END */
 100
 101 static char *dma_buffer;
 102 static int dma_bytes;
 103 static struct esp_pio_buffer *free_pio_buf;
 104
 105 #define DMA_BUFFER_SZ 1024
 106
 107 #define WAKEUP_CHARS 1024
 108
 109 static char serial_name[] __initdata = "ESP serial driver";
 110 static char serial_version[] __initdata = "2.2";
 111
 112 static struct tty_driver *esp_driver;
 113
 114 /*
 115  * Serial driver configuration section.  Here are the various options:
 116  *
 117  * SERIAL_PARANOIA_CHECK
 118  *              Check the magic number for the esp_structure where
 119  *              ever possible.
 120  */
 121
 122 #undef SERIAL_PARANOIA_CHECK
 123 #define SERIAL_DO_RESTART
 124
 125 #undef SERIAL_DEBUG_INTR
 126 #undef SERIAL_DEBUG_OPEN
 127 #undef SERIAL_DEBUG_FLOW
 128
 129 #if defined(MODULE) && defined(SERIAL_DEBUG_MCOUNT)
 130 #define DBG_CNT(s) printk(KERN_DEBUG "(%s): [%x] refc=%d, serc=%d, ttyc=%d -> %s\n", \
 131                                 tty->name, info->port.flags, \
 132                                 serial_driver.refcount, \
 133                                 info->port.count, tty->count, s)
 134 #else
 135 #define DBG_CNT(s)
 136 #endif
 137
 138 static struct esp_struct *ports;
 139
 140 static void change_speed(struct esp_struct *info);
 141 static void rs_wait_until_sent(struct tty_struct *, int);
 142
 143 /*
 144  * The ESP card has a clock rate of 14.7456 MHz (that is, 2**ESPC_SCALE
 145  * times the normal 1.8432 Mhz clock of most serial boards).
 146  */
 147 #define BASE_BAUD ((1843200 / 16) * (1 << ESPC_SCALE))
 148
 149 /* Standard COM flags (except for COM4, because of the 8514 problem) */
 150 #define STD_COM_FLAGS (ASYNC_BOOT_AUTOCONF | ASYNC_SKIP_TEST)
 151
 152 static inline int serial_paranoia_check(struct esp_struct *info,
 153                                         char *name, const char *routine)
 154 {
 155 #ifdef SERIAL_PARANOIA_CHECK
 156         static const char badmagic[] = KERN_WARNING
 157                 "Warning: bad magic number for serial struct (%s) in %s\n";
 158         static const char badinfo[] = KERN_WARNING
 159                 "Warning: null esp_struct for (%s) in %s\n";
 160
 161         if (!info) {
 162                 printk(badinfo, name, routine);
 163                 return 1;
 164         }
 165         if (info->magic != ESP_MAGIC) {
 166                 printk(badmagic, name, routine);
 167                 return 1;
 168         }
 169 #endif
 170         return 0;
 171 }
 172
 173 static inline unsigned int serial_in(struct esp_struct *info, int offset)
 174 {
 175         return inb(info->io_port + offset);
 176 }
 177
 178 static inline void serial_out(struct esp_struct *info, int offset,
 179                               unsigned char value)
 180 {
 181         outb(value, info->io_port+offset);
 182 }
 183
 184 /*
 185  * ------------------------------------------------------------
 186  * rs_stop() and rs_start()
 187  *
 188  * This routines are called before setting or resetting tty->stopped.
 189  * They enable or disable transmitter interrupts, as necessary.
 190  * ------------------------------------------------------------
 191  */
 192 static void rs_stop(struct tty_struct *tty)
 193 {
 194         struct esp_struct *info = tty->driver_data;
 195         unsigned long flags;
 196
 197         if (serial_paranoia_check(info, tty->name, "rs_stop"))
 198                 return;
 199
 200         spin_lock_irqsave(&info->lock, flags);
 201         if (info->IER & UART_IER_THRI) {
 202                 info->IER &= ~UART_IER_THRI;
 203                 serial_out(info, UART_ESI_CMD1, ESI_SET_SRV_MASK);
 204                 serial_out(info, UART_ESI_CMD2, info->IER);
 205         }
 206         spin_unlock_irqrestore(&info->lock, flags);
 207 }
 208
 209 static void rs_start(struct tty_struct *tty)
 210 {
 211         struct esp_struct *info = tty->driver_data;
 212         unsigned long flags;
 213
 214         if (serial_paranoia_check(info, tty->name, "rs_start"))
 215                 return;
 216
 217         spin_lock_irqsave(&info->lock, flags);
 218         if (info->xmit_cnt && info->xmit_buf && !(info->IER & UART_IER_THRI)) {
 219                 info->IER |= UART_IER_THRI;
 220                 serial_out(info, UART_ESI_CMD1, ESI_SET_SRV_MASK);
 221                 serial_out(info, UART_ESI_CMD2, info->IER);
 222         }
 223         spin_unlock_irqrestore(&info->lock, flags);
 224 }
 225
 226 /*
 227  * ----------------------------------------------------------------------
 228  *
 229  * Here starts the interrupt handling routines.  All of the following
 230  * subroutines are declared as inline and are folded into
 231  * rs_interrupt().  They were separated out for readability's sake.
 232  *
 233  * Note: rs_interrupt() is a "fast" interrupt, which means that it
 234  * runs with interrupts turned off.  People who may want to modify
 235  * rs_interrupt() should try to keep the interrupt handler as fast as
 236  * possible.  After you are done making modifications, it is not a bad
 237  * idea to do:
 238  *
 239  * gcc -S -DKERNEL -Wall -Wstrict-prototypes -O6 -fomit-frame-pointer serial.c
 240  *
 241  * and look at the resulting assemble code in serial.s.
 242  *
 243  *                              - Ted Ts'o (tytso@mit.edu), 7-Mar-93
 244  * -----------------------------------------------------------------------
 245  */
 246
 247 static DEFINE_SPINLOCK(pio_lock);
 248
 249 static inline struct esp_pio_buffer *get_pio_buffer(void)
 250 {
 251         struct esp_pio_buffer *buf;
 252         unsigned long flags;
 253
 254         spin_lock_irqsave(&pio_lock, flags);
 255         if (free_pio_buf) {
 256                 buf = free_pio_buf;
 257                 free_pio_buf = buf->next;
 258         } else {
 259                 buf = kmalloc(sizeof(struct esp_pio_buffer), GFP_ATOMIC);
 260         }
 261         spin_unlock_irqrestore(&pio_lock, flags);
 262         return buf;
 263 }
 264
 265 static inline void release_pio_buffer(struct esp_pio_buffer *buf)
 266 {
 267         unsigned long flags;
 268         spin_lock_irqsave(&pio_lock, flags);
 269         buf->next = free_pio_buf;
 270         free_pio_buf = buf;
 271         spin_unlock_irqrestore(&pio_lock, flags);
 272 }
 273
 274 static inline void receive_chars_pio(struct esp_struct *info, int num_bytes)
 275 {
 276         struct tty_struct *tty = info->port.tty;
 277         int i;
 278         struct esp_pio_buffer *pio_buf;
 279         struct esp_pio_buffer *err_buf;
 280         unsigned char status_mask;
 281
 282         pio_buf = get_pio_buffer();
 283
 284         if (!pio_buf)
 285                 return;
 286
 287         err_buf = get_pio_buffer();
 288
 289         if (!err_buf) {
 290                 release_pio_buffer(pio_buf);
 291                 return;
 292         }
 293
 294         status_mask = (info->read_status_mask >> 2) & 0x07;
 295
 296         for (i = 0; i < num_bytes - 1; i += 2) {
 297                 *((unsigned short *)(pio_buf->data + i)) =
 298                         inw(info->io_port + UART_ESI_RX);
 299                 err_buf->data[i] = serial_in(info, UART_ESI_RWS);
 300                 err_buf->data[i + 1] = (err_buf->data[i] >> 3) & status_mask;
 301                 err_buf->data[i] &= status_mask;
 302         }
 303
 304         if (num_bytes & 0x0001) {
 305                 pio_buf->data[num_bytes - 1] = serial_in(info, UART_ESI_RX);
 306                 err_buf->data[num_bytes - 1] =
 307                         (serial_in(info, UART_ESI_RWS) >> 3) & status_mask;
 308         }
 309
 310         /* make sure everything is still ok since interrupts were enabled */
 311         tty = info->port.tty;
 312
 313         if (!tty) {
 314                 release_pio_buffer(pio_buf);
 315                 release_pio_buffer(err_buf);
 316                 info->stat_flags &= ~ESP_STAT_RX_TIMEOUT;
 317                 return;
 318         }
 319
 320         status_mask = (info->ignore_status_mask >> 2) & 0x07;
 321
 322         for (i = 0; i < num_bytes; i++) {
 323                 if (!(err_buf->data[i] & status_mask)) {
 324                         int flag = 0;
 325
 326                         if (err_buf->data[i] & 0x04) {
 327                                 flag = TTY_BREAK;
 328                                 if (info->port.flags & ASYNC_SAK)
 329                                         do_SAK(tty);
 330                         } else if (err_buf->data[i] & 0x02)
 331                                 flag = TTY_FRAME;
 332                         else if (err_buf->data[i] & 0x01)
 333                                 flag = TTY_PARITY;
 334                         tty_insert_flip_char(tty, pio_buf->data[i], flag);
 335                 }
 336         }
 337
 338         tty_schedule_flip(tty);
 339
 340         info->stat_flags &= ~ESP_STAT_RX_TIMEOUT;
 341         release_pio_buffer(pio_buf);
 342         release_pio_buffer(err_buf);
 343 }
 344
 345 static void program_isa_dma(int dma, int dir, unsigned long addr, int len)
 346 {
 347         unsigned long flags;
 348
 349         flags = claim_dma_lock();
 350         disable_dma(dma);
 351         clear_dma_ff(dma);
 352         set_dma_mode(dma, dir);
 353         set_dma_addr(dma, addr);
 354         set_dma_count(dma, len);
 355         enable_dma(dma);
 356         release_dma_lock(flags);
 357 }
 358
 359 static void receive_chars_dma(struct esp_struct *info, int num_bytes)
 360 {
 361         info->stat_flags &= ~ESP_STAT_RX_TIMEOUT;
 362         dma_bytes = num_bytes;
 363         info->stat_flags |= ESP_STAT_DMA_RX;
 364
 365         program_isa_dma(dma, DMA_MODE_READ, isa_virt_to_bus(dma_buffer),
 366                                                                 dma_bytes);
 367         serial_out(info, UART_ESI_CMD1, ESI_START_DMA_RX);
 368 }
 369
 370 static inline void receive_chars_dma_done(struct esp_struct *info,
 371                                             int status)
 372 {
 373         struct tty_struct *tty = info->port.tty;
 374         int num_bytes;
 375         unsigned long flags;
 376
 377         flags = claim_dma_lock();
 378         disable_dma(dma);
 379         clear_dma_ff(dma);
 380
 381         info->stat_flags &= ~ESP_STAT_DMA_RX;
 382         num_bytes = dma_bytes - get_dma_residue(dma);
 383         release_dma_lock(flags);
 384
 385         info->icount.rx += num_bytes;
 386
 387         if (num_bytes > 0) {
 388                 tty_insert_flip_string(tty, dma_buffer, num_bytes - 1);
 389
 390                 status &= (0x1c & info->read_status_mask);
 391
 392                 /* Is the status significant or do we throw the last byte ? */
 393                 if (!(status & info->ignore_status_mask)) {
 394                         int statflag = 0;
 395
 396                         if (status & 0x10) {
 397                                 statflag = TTY_BREAK;
 398                                 (info->icount.brk)++;
 399                                 if (info->port.flags & ASYNC_SAK)
 400                                         do_SAK(tty);
 401                         } else if (status & 0x08) {
 402                                 statflag = TTY_FRAME;
 403                                 info->icount.frame++;
 404                         } else if (status & 0x04) {
 405                                 statflag = TTY_PARITY;
 406                                 info->icount.parity++;
 407                         }
 408                         tty_insert_flip_char(tty, dma_buffer[num_bytes - 1],
 409                                                                 statflag);
 410                 }
 411                 tty_schedule_flip(tty);
 412         }
 413
 414         if (dma_bytes != num_bytes) {
 415                 num_bytes = dma_bytes - num_bytes;
 416                 dma_bytes = 0;
 417                 receive_chars_dma(info, num_bytes);
 418         } else
 419                 dma_bytes = 0;
 420 }
 421
 422 /* Caller must hold info->lock */
 423
 424 static inline void transmit_chars_pio(struct esp_struct *info,
 425                                         int space_avail)
 426 {
 427         int i;
 428         struct esp_pio_buffer *pio_buf;
 429
 430         pio_buf = get_pio_buffer();
 431
 432         if (!pio_buf)
 433                 return;
 434
 435         while (space_avail && info->xmit_cnt) {
 436                 if (info->xmit_tail + space_avail <= ESP_XMIT_SIZE) {
 437                         memcpy(pio_buf->data,
 438                                &(info->xmit_buf[info->xmit_tail]),
 439                                space_avail);
 440                 } else {
 441                         i = ESP_XMIT_SIZE - info->xmit_tail;
 442                         memcpy(pio_buf->data,
 443                                &(info->xmit_buf[info->xmit_tail]), i);
 444                         memcpy(&(pio_buf->data[i]), info->xmit_buf,
 445                                space_avail - i);
 446                 }
 447
 448                 info->xmit_cnt -= space_avail;
 449                 info->xmit_tail = (info->xmit_tail + space_avail) &
 450                         (ESP_XMIT_SIZE - 1);
 451
 452                 for (i = 0; i < space_avail - 1; i += 2) {
 453                         outw(*((unsigned short *)(pio_buf->data + i)),
 454                              info->io_port + UART_ESI_TX);
 455                 }
 456
 457                 if (space_avail & 0x0001)
 458                         serial_out(info, UART_ESI_TX,
 459                                    pio_buf->data[space_avail - 1]);
 460
 461                 if (info->xmit_cnt) {
 462                         serial_out(info, UART_ESI_CMD1, ESI_NO_COMMAND);
 463                         serial_out(info, UART_ESI_CMD1, ESI_GET_TX_AVAIL);
 464                         space_avail = serial_in(info, UART_ESI_STAT1) << 8;
 465                         space_avail |= serial_in(info, UART_ESI_STAT2);
 466
 467                         if (space_avail > info->xmit_cnt)
 468                                 space_avail = info->xmit_cnt;
 469                 }
 470         }
 471
 472         if (info->xmit_cnt < WAKEUP_CHARS) {
 473                 if (info->port.tty)
 474                         tty_wakeup(info->port.tty);
 475
 476 #ifdef SERIAL_DEBUG_INTR
 477                 printk("THRE...");
 478 #endif
 479
 480                 if (info->xmit_cnt <= 0) {
 481                         info->IER &= ~UART_IER_THRI;
 482                         serial_out(info, UART_ESI_CMD1,
 483                                    ESI_SET_SRV_MASK);
 484                         serial_out(info, UART_ESI_CMD2, info->IER);
 485                 }
 486         }
 487
 488         release_pio_buffer(pio_buf);
 489 }
 490
 491 /* Caller must hold info->lock */
 492 static inline void transmit_chars_dma(struct esp_struct *info, int num_bytes)
 493 {
 494         dma_bytes = num_bytes;
 495
 496         if (info->xmit_tail + dma_bytes <= ESP_XMIT_SIZE) {
 497                 memcpy(dma_buffer, &(info->xmit_buf[info->xmit_tail]),
 498                        dma_bytes);
 499         } else {
 500                 int i = ESP_XMIT_SIZE - info->xmit_tail;
 501                 memcpy(dma_buffer, &(info->xmit_buf[info->xmit_tail]),
 502                         i);
 503                 memcpy(&(dma_buffer[i]), info->xmit_buf, dma_bytes - i);
 504         }
 505
 506         info->xmit_cnt -= dma_bytes;
 507         info->xmit_tail = (info->xmit_tail + dma_bytes) & (ESP_XMIT_SIZE - 1);
 508
 509         if (info->xmit_cnt < WAKEUP_CHARS) {
 510                 if (info->port.tty)
 511                         tty_wakeup(info->port.tty);
 512
 513 #ifdef SERIAL_DEBUG_INTR
 514                 printk("THRE...");
 515 #endif
 516
 517                 if (info->xmit_cnt <= 0) {
 518                         info->IER &= ~UART_IER_THRI;
 519                         serial_out(info, UART_ESI_CMD1, ESI_SET_SRV_MASK);
 520                         serial_out(info, UART_ESI_CMD2, info->IER);
 521                 }
 522         }
 523
 524         info->stat_flags |= ESP_STAT_DMA_TX;
 525
 526         program_isa_dma(dma, DMA_MODE_WRITE, isa_virt_to_bus(dma_buffer),
 527                                                                 dma_bytes);
 528         serial_out(info, UART_ESI_CMD1, ESI_START_DMA_TX);
 529 }
 530
 531 static inline void transmit_chars_dma_done(struct esp_struct *info)
 532 {
 533         int num_bytes;
 534         unsigned long flags;
 535
 536         flags = claim_dma_lock();
 537         disable_dma(dma);
 538         clear_dma_ff(dma);
 539
 540         num_bytes = dma_bytes - get_dma_residue(dma);
 541         info->icount.tx += dma_bytes;
 542         release_dma_lock(flags);
 543
 544         if (dma_bytes != num_bytes) {
 545                 dma_bytes -= num_bytes;
 546                 memmove(dma_buffer, dma_buffer + num_bytes, dma_bytes);
 547
 548                 program_isa_dma(dma, DMA_MODE_WRITE,
 549                                 isa_virt_to_bus(dma_buffer), dma_bytes);
 550
 551                 serial_out(info, UART_ESI_CMD1, ESI_START_DMA_TX);
 552         } else {
 553                 dma_bytes = 0;
 554                 info->stat_flags &= ~ESP_STAT_DMA_TX;
 555         }
 556 }
 557
 558 static void check_modem_status(struct esp_struct *info)
 559 {
 560         int     status;
 561
 562         serial_out(info, UART_ESI_CMD1, ESI_GET_UART_STAT);
 563         status = serial_in(info, UART_ESI_STAT2);
 564
 565         if (status & UART_MSR_ANY_DELTA) {
 566                 /* update input line counters */
 567                 if (status & UART_MSR_TERI)
 568                         info->icount.rng++;
 569                 if (status & UART_MSR_DDSR)
 570                         info->icount.dsr++;
 571                 if (status & UART_MSR_DDCD)
 572                         info->icount.dcd++;
 573                 if (status & UART_MSR_DCTS)
 574                         info->icount.cts++;
 575                 wake_up_interruptible(&info->delta_msr_wait);
 576         }
 577
 578         if ((info->port.flags & ASYNC_CHECK_CD) && (status & UART_MSR_DDCD)) {
 579 #if (defined(SERIAL_DEBUG_OPEN) || defined(SERIAL_DEBUG_INTR))
 580                 printk("ttys%d CD now %s...", info->line,
 581                        (status & UART_MSR_DCD) ? "on" : "off");
 582 #endif
 583                 if (status & UART_MSR_DCD)
 584                         wake_up_interruptible(&info->port.open_wait);
 585                 else {
 586 #ifdef SERIAL_DEBUG_OPEN
 587                         printk("scheduling hangup...");
 588 #endif
 589                         tty_hangup(info->port.tty);
 590                 }
 591         }
 592 }
 593
 594 /*
 595  * This is the serial driver's interrupt routine
 596  */
 597 static irqreturn_t rs_interrupt_single(int irq, void *dev_id)
 598 {
 599         struct esp_struct *info;
 600         unsigned err_status;
 601         unsigned int scratch;
 602
 603 #ifdef SERIAL_DEBUG_INTR
 604         printk("rs_interrupt_single(%d)...", irq);
 605 #endif
 606         info = (struct esp_struct *)dev_id;
 607         err_status = 0;
 608         scratch = serial_in(info, UART_ESI_SID);
 609
 610         spin_lock(&info->lock);
 611
 612         if (!info->port.tty) {
 613                 spin_unlock(&info->lock);
 614                 return IRQ_NONE;
 615         }
 616
 617         if (scratch & 0x04) { /* error */
 618                 serial_out(info, UART_ESI_CMD1, ESI_GET_ERR_STAT);
 619                 err_status = serial_in(info, UART_ESI_STAT1);
 620                 serial_in(info, UART_ESI_STAT2);
 621
 622                 if (err_status & 0x01)
 623                         info->stat_flags |= ESP_STAT_RX_TIMEOUT;
 624
 625                 if (err_status & 0x20) /* UART status */
 626                         check_modem_status(info);
 627
 628                 if (err_status & 0x80) /* Start break */
 629                         wake_up_interruptible(&info->break_wait);
 630         }
 631
 632         if ((scratch & 0x88) || /* DMA completed or timed out */
 633             (err_status & 0x1c) /* receive error */) {
 634                 if (info->stat_flags & ESP_STAT_DMA_RX)
 635                         receive_chars_dma_done(info, err_status);
 636                 else if (info->stat_flags & ESP_STAT_DMA_TX)
 637                         transmit_chars_dma_done(info);
 638         }
 639
 640         if (!(info->stat_flags & (ESP_STAT_DMA_RX | ESP_STAT_DMA_TX)) &&
 641             ((scratch & 0x01) || (info->stat_flags & ESP_STAT_RX_TIMEOUT)) &&
 642             (info->IER & UART_IER_RDI)) {
 643                 int num_bytes;
 644
 645                 serial_out(info, UART_ESI_CMD1, ESI_NO_COMMAND);
 646                 serial_out(info, UART_ESI_CMD1, ESI_GET_RX_AVAIL);
 647                 num_bytes = serial_in(info, UART_ESI_STAT1) << 8;
 648                 num_bytes |= serial_in(info, UART_ESI_STAT2);
 649
 650                 num_bytes = tty_buffer_request_room(info->port.tty, num_bytes);
 651
 652                 if (num_bytes) {
 653                         if (dma_bytes ||
 654                             (info->stat_flags & ESP_STAT_USE_PIO) ||
 655                             (num_bytes <= info->config.pio_threshold))
 656                                 receive_chars_pio(info, num_bytes);
 657                         else
 658                                 receive_chars_dma(info, num_bytes);
 659                 }
 660         }
 661
 662         if (!(info->stat_flags & (ESP_STAT_DMA_RX | ESP_STAT_DMA_TX)) &&
 663             (scratch & 0x02) && (info->IER & UART_IER_THRI)) {
 664                 if ((info->xmit_cnt <= 0) || info->port.tty->stopped) {
 665                         info->IER &= ~UART_IER_THRI;
 666                         serial_out(info, UART_ESI_CMD1, ESI_SET_SRV_MASK);
 667                         serial_out(info, UART_ESI_CMD2, info->IER);
 668                 } else {
 669                         int num_bytes;
 670
 671                         serial_out(info, UART_ESI_CMD1, ESI_NO_COMMAND);
 672                         serial_out(info, UART_ESI_CMD1, ESI_GET_TX_AVAIL);
 673                         num_bytes = serial_in(info, UART_ESI_STAT1) << 8;
 674                         num_bytes |= serial_in(info, UART_ESI_STAT2);
 675
 676                         if (num_bytes > info->xmit_cnt)
 677                                 num_bytes = info->xmit_cnt;
 678
 679                         if (num_bytes) {
 680                                 if (dma_bytes ||
 681                                     (info->stat_flags & ESP_STAT_USE_PIO) ||
 682                                     (num_bytes <= info->config.pio_threshold))
 683                                         transmit_chars_pio(info, num_bytes);
 684                                 else
 685                                         transmit_chars_dma(info, num_bytes);
 686                         }
 687                 }
 688         }
 689
 690         info->last_active = jiffies;
 691
 692 #ifdef SERIAL_DEBUG_INTR
 693         printk("end.\n");
 694 #endif
 695         spin_unlock(&info->lock);
 696         return IRQ_HANDLED;
 697 }
 698
 699 /*
 700  * -------------------------------------------------------------------
 701  * Here ends the serial interrupt routines.
 702  * -------------------------------------------------------------------
 703  */
 704
 705 /*
 706  * ---------------------------------------------------------------
 707  * Low level utility subroutines for the serial driver:  routines to
 708  * figure out the appropriate timeout for an interrupt chain, routines
 709  * to initialize and startup a serial port, and routines to shutdown a
 710  * serial port.  Useful stuff like that.
 711  *
 712  * Caller should hold lock
 713  * ---------------------------------------------------------------
 714  */
 715
 716 static void esp_basic_init(struct esp_struct *info)
 717 {
 718         /* put ESPC in enhanced mode */
 719         serial_out(info, UART_ESI_CMD1, ESI_SET_MODE);
 720
 721         if (info->stat_flags & ESP_STAT_NEVER_DMA)
 722                 serial_out(info, UART_ESI_CMD2, 0x01);
 723         else
 724                 serial_out(info, UART_ESI_CMD2, 0x31);
 725
 726         /* disable interrupts for now */
 727         serial_out(info, UART_ESI_CMD1, ESI_SET_SRV_MASK);
 728         serial_out(info, UART_ESI_CMD2, 0x00);
 729
 730         /* set interrupt and DMA channel */
 731         serial_out(info, UART_ESI_CMD1, ESI_SET_IRQ);
 732
 733         if (info->stat_flags & ESP_STAT_NEVER_DMA)
 734                 serial_out(info, UART_ESI_CMD2, 0x01);
 735         else
 736                 serial_out(info, UART_ESI_CMD2, (dma << 4) | 0x01);
 737
 738         serial_out(info, UART_ESI_CMD1, ESI_SET_ENH_IRQ);
 739
 740         if (info->line % 8)     /* secondary port */
 741                 serial_out(info, UART_ESI_CMD2, 0x0d);  /* shared */
 742         else if (info->irq == 9)
 743                 serial_out(info, UART_ESI_CMD2, 0x02);
 744         else
 745                 serial_out(info, UART_ESI_CMD2, info->irq);
 746
 747         /* set error status mask (check this) */
 748         serial_out(info, UART_ESI_CMD1, ESI_SET_ERR_MASK);
 749
 750         if (info->stat_flags & ESP_STAT_NEVER_DMA)
 751                 serial_out(info, UART_ESI_CMD2, 0xa1);
 752         else
 753                 serial_out(info, UART_ESI_CMD2, 0xbd);
 754
 755         serial_out(info, UART_ESI_CMD2, 0x00);
 756
 757         /* set DMA timeout */
 758         serial_out(info, UART_ESI_CMD1, ESI_SET_DMA_TMOUT);
 759         serial_out(info, UART_ESI_CMD2, 0xff);
 760
 761         /* set FIFO trigger levels */
 762         serial_out(info, UART_ESI_CMD1, ESI_SET_TRIGGER);
 763         serial_out(info, UART_ESI_CMD2, info->config.rx_trigger >> 8);
 764         serial_out(info, UART_ESI_CMD2, info->config.rx_trigger);
 765         serial_out(info, UART_ESI_CMD2, info->config.tx_trigger >> 8);
 766         serial_out(info, UART_ESI_CMD2, info->config.tx_trigger);
 767
 768         /* Set clock scaling and wait states */
 769         serial_out(info, UART_ESI_CMD1, ESI_SET_PRESCALAR);
 770         serial_out(info, UART_ESI_CMD2, 0x04 | ESPC_SCALE);
 771
 772         /* set reinterrupt pacing */
 773         serial_out(info, UART_ESI_CMD1, ESI_SET_REINTR);
 774         serial_out(info, UART_ESI_CMD2, 0xff);
 775 }
 776
 777 static int startup(struct esp_struct *info)
 778 {
 779         unsigned long flags;
 780         int     retval = 0;
 781         unsigned int num_chars;
 782
 783         spin_lock_irqsave(&info->lock, flags);
 784
 785         if (info->port.flags & ASYNC_INITIALIZED)
 786                 goto out;
 787
 788         if (!info->xmit_buf) {
 789                 info->xmit_buf = (unsigned char *)get_zeroed_page(GFP_ATOMIC);
 790                 retval = -ENOMEM;
 791                 if (!info->xmit_buf)
 792                         goto out;
 793         }
 794
 795 #ifdef SERIAL_DEBUG_OPEN
 796         printk(KERN_DEBUG "starting up ttys%d (irq %d)...",
 797                                                 info->line, info->irq);
 798 #endif
 799
 800         /* Flush the RX buffer.  Using the ESI flush command may cause */
 801         /* wild interrupts, so read all the data instead. */
 802
 803         serial_out(info, UART_ESI_CMD1, ESI_NO_COMMAND);
 804         serial_out(info, UART_ESI_CMD1, ESI_GET_RX_AVAIL);
 805         num_chars = serial_in(info, UART_ESI_STAT1) << 8;
 806         num_chars |= serial_in(info, UART_ESI_STAT2);
 807
 808         while (num_chars > 1) {
 809                 inw(info->io_port + UART_ESI_RX);
 810                 num_chars -= 2;
 811         }
 812
 813         if (num_chars)
 814                 serial_in(info, UART_ESI_RX);
 815
 816         /* set receive character timeout */
 817         serial_out(info, UART_ESI_CMD1, ESI_SET_RX_TIMEOUT);
 818         serial_out(info, UART_ESI_CMD2, info->config.rx_timeout);
 819
 820         /* clear all flags except the "never DMA" flag */
 821         info->stat_flags &= ESP_STAT_NEVER_DMA;
 822
 823         if (info->stat_flags & ESP_STAT_NEVER_DMA)
 824                 info->stat_flags |= ESP_STAT_USE_PIO;
 825
 826         spin_unlock_irqrestore(&info->lock, flags);
 827
 828         /*
 829          * Allocate the IRQ
 830          */
 831
 832         retval = request_irq(info->irq, rs_interrupt_single, IRQF_SHARED,
 833                              "esp serial", info);
 834
 835         if (retval) {
 836                 if (capable(CAP_SYS_ADMIN)) {
 837                         if (info->port.tty)
 838                                 set_bit(TTY_IO_ERROR,
 839                                         &info->port.tty->flags);
 840                         retval = 0;
 841                 }
 842                 goto out_unlocked;
 843         }
 844
 845         if (!(info->stat_flags & ESP_STAT_USE_PIO) && !dma_buffer) {
 846                 dma_buffer = (char *)__get_dma_pages(
 847                         GFP_KERNEL, get_order(DMA_BUFFER_SZ));
 848
 849                 /* use PIO mode if DMA buf/chan cannot be allocated */
 850                 if (!dma_buffer)
 851                         info->stat_flags |= ESP_STAT_USE_PIO;
 852                 else if (request_dma(dma, "esp serial")) {
 853                         free_pages((unsigned long)dma_buffer,
 854                                    get_order(DMA_BUFFER_SZ));
 855                         dma_buffer = NULL;
 856                         info->stat_flags |= ESP_STAT_USE_PIO;
 857                 }
 858
 859         }
 860
 861         info->MCR = UART_MCR_DTR | UART_MCR_RTS | UART_MCR_OUT2;
 862
 863         spin_lock_irqsave(&info->lock, flags);
 864         serial_out(info, UART_ESI_CMD1, ESI_WRITE_UART);
 865         serial_out(info, UART_ESI_CMD2, UART_MCR);
 866         serial_out(info, UART_ESI_CMD2, info->MCR);
 867
 868         /*
 869          * Finally, enable interrupts
 870          */
 871         /* info->IER = UART_IER_MSI | UART_IER_RLSI | UART_IER_RDI; */
 872         info->IER = UART_IER_RLSI | UART_IER_RDI | UART_IER_DMA_TMOUT |
 873                         UART_IER_DMA_TC;
 874         serial_out(info, UART_ESI_CMD1, ESI_SET_SRV_MASK);
 875         serial_out(info, UART_ESI_CMD2, info->IER);
 876
 877         if (info->port.tty)
 878                 clear_bit(TTY_IO_ERROR, &info->port.tty->flags);
 879         info->xmit_cnt = info->xmit_head = info->xmit_tail = 0;
 880         spin_unlock_irqrestore(&info->lock, flags);
 881
 882         /*
 883          * Set up the tty->alt_speed kludge
 884          */
 885         if (info->port.tty) {
 886                 if ((info->port.flags & ASYNC_SPD_MASK) == ASYNC_SPD_HI)
 887                         info->port.tty->alt_speed = 57600;
 888                 if ((info->port.flags & ASYNC_SPD_MASK) == ASYNC_SPD_VHI)
 889                         info->port.tty->alt_speed = 115200;
 890                 if ((info->port.flags & ASYNC_SPD_MASK) == ASYNC_SPD_SHI)
 891                         info->port.tty->alt_speed = 230400;
 892                 if ((info->port.flags & ASYNC_SPD_MASK) == ASYNC_SPD_WARP)
 893                         info->port.tty->alt_speed = 460800;
 894         }
 895
 896         /*
 897          * set the speed of the serial port
 898          */
 899         change_speed(info);
 900         info->port.flags |= ASYNC_INITIALIZED;
 901         return 0;
 902
 903 out:
 904         spin_unlock_irqrestore(&info->lock, flags);
 905 out_unlocked:
 906         return retval;
 907 }
 908
 909 /*
 910  * This routine will shutdown a serial port; interrupts are disabled, and
 911  * DTR is dropped if the hangup on close termio flag is on.
 912  */
 913 static void shutdown(struct esp_struct *info)
 914 {
 915         unsigned long   flags, f;
 916
 917         if (!(info->port.flags & ASYNC_INITIALIZED))
 918                 return;
 919
 920 #ifdef SERIAL_DEBUG_OPEN
 921         printk("Shutting down serial port %d (irq %d)....", info->line,
 922                info->irq);
 923 #endif
 924
 925         spin_lock_irqsave(&info->lock, flags);
 926         /*
 927          * clear delta_msr_wait queue to avoid mem leaks: we may free the irq
 928          * here so the queue might never be waken up
 929          */
 930         wake_up_interruptible(&info->delta_msr_wait);
 931         wake_up_interruptible(&info->break_wait);
 932
 933         /* stop a DMA transfer on the port being closed */
 934         /* DMA lock is higher priority always */
 935         if (info->stat_flags & (ESP_STAT_DMA_RX | ESP_STAT_DMA_TX)) {
 936                 f = claim_dma_lock();
 937                 disable_dma(dma);
 938                 clear_dma_ff(dma);
 939                 release_dma_lock(f);
 940
 941                 dma_bytes = 0;
 942         }
 943
 944         /*
 945          * Free the IRQ
 946          */
 947         free_irq(info->irq, info);
 948
 949         if (dma_buffer) {
 950                 struct esp_struct *current_port = ports;
 951
 952                 while (current_port) {
 953                         if ((current_port != info) &&
 954                             (current_port->port.flags & ASYNC_INITIALIZED))
 955                                 break;
 956
 957                         current_port = current_port->next_port;
 958                 }
 959
 960                 if (!current_port) {
 961                         free_dma(dma);
 962                         free_pages((unsigned long)dma_buffer,
 963                                    get_order(DMA_BUFFER_SZ));
 964                         dma_buffer = NULL;
 965                 }
 966         }
 967
 968         if (info->xmit_buf) {
 969                 free_page((unsigned long) info->xmit_buf);
 970                 info->xmit_buf = NULL;
 971         }
 972
 973         info->IER = 0;
 974         serial_out(info, UART_ESI_CMD1, ESI_SET_SRV_MASK);
 975         serial_out(info, UART_ESI_CMD2, 0x00);
 976
 977         if (!info->port.tty || (info->port.tty->termios->c_cflag & HUPCL))
 978                 info->MCR &= ~(UART_MCR_DTR|UART_MCR_RTS);
 979
 980         info->MCR &= ~UART_MCR_OUT2;
 981         serial_out(info, UART_ESI_CMD1, ESI_WRITE_UART);
 982         serial_out(info, UART_ESI_CMD2, UART_MCR);
 983         serial_out(info, UART_ESI_CMD2, info->MCR);
 984
 985         if (info->port.tty)
 986                 set_bit(TTY_IO_ERROR, &info->port.tty->flags);
 987
 988         info->port.flags &= ~ASYNC_INITIALIZED;
 989         spin_unlock_irqrestore(&info->lock, flags);
 990 }
 991
 992 /*
 993  * This routine is called to set the UART divisor registers to match
 994  * the specified baud rate for a serial port.
 995  */
 996 static void change_speed(struct esp_struct *info)
 997 {
 998         unsigned short port;
 999         int     quot = 0;
1000         unsigned cflag, cval;
1001         int     baud, bits;
1002         unsigned char flow1 = 0, flow2 = 0;
1003         unsigned long flags;
1004
1005         if (!info->port.tty || !info->port.tty->termios)
1006                 return;
1007         cflag = info->port.tty->termios->c_cflag;
1008         port = info->io_port;
1009
1010         /* byte size and parity */
1011         switch (cflag & CSIZE) {
1012         case CS5: cval = 0x00; bits = 7; break;
1013         case CS6: cval = 0x01; bits = 8; break;
1014         case CS7: cval = 0x02; bits = 9; break;
1015         case CS8: cval = 0x03; bits = 10; break;
1016         default:  cval = 0x00; bits = 7; break;
1017         }
1018         if (cflag & CSTOPB) {
1019                 cval |= 0x04;
1020                 bits++;
1021         }
1022         if (cflag & PARENB) {
1023                 cval |= UART_LCR_PARITY;
1024                 bits++;
1025         }
1026         if (!(cflag & PARODD))
1027                 cval |= UART_LCR_EPAR;
1028 #ifdef CMSPAR
1029         if (cflag & CMSPAR)
1030                 cval |= UART_LCR_SPAR;
1031 #endif
1032         baud = tty_get_baud_rate(info->port.tty);
1033         if (baud == 38400 &&
1034                 ((info->port.flags & ASYNC_SPD_MASK) == ASYNC_SPD_CUST))
1035                 quot = info->custom_divisor;
1036         else {
1037                 if (baud == 134) /* Special case since 134 is really 134.5 */
1038                         quot = (2*BASE_BAUD / 269);
1039                 else if (baud)
1040                         quot = BASE_BAUD / baud;
1041         }
1042         /* If the quotient is ever zero, default to 9600 bps */
1043         if (!quot)
1044                 quot = BASE_BAUD / 9600;
1045
1046         if (baud) {
1047                 /* Actual rate */
1048                 baud = BASE_BAUD/quot;
1049                 tty_encode_baud_rate(info->port.tty, baud, baud);
1050         }
1051         info->timeout = ((1024 * HZ * bits * quot) / BASE_BAUD) + (HZ / 50);
1052
1053         /* CTS flow control flag and modem status interrupts */
1054         /* info->IER &= ~UART_IER_MSI; */
1055         if (cflag & CRTSCTS) {
1056                 info->port.flags |= ASYNC_CTS_FLOW;
1057                 /* info->IER |= UART_IER_MSI; */
1058                 flow1 = 0x04;
1059                 flow2 = 0x10;
1060         } else
1061                 info->port.flags &= ~ASYNC_CTS_FLOW;
1062         if (cflag & CLOCAL)
1063                 info->port.flags &= ~ASYNC_CHECK_CD;
1064         else
1065                 info->port.flags |= ASYNC_CHECK_CD;
1066
1067         /*
1068          * Set up parity check flag
1069          */
1070         info->read_status_mask = UART_LSR_OE | UART_LSR_THRE | UART_LSR_DR;
1071         if (I_INPCK(info->port.tty))
1072                 info->read_status_mask |= UART_LSR_FE | UART_LSR_PE;
1073         if (I_BRKINT(info->port.tty) || I_PARMRK(info->port.tty))
1074                 info->read_status_mask |= UART_LSR_BI;
1075
1076         info->ignore_status_mask = 0;
1077 #if 0
1078         /* This should be safe, but for some broken bits of hardware... */
1079         if (I_IGNPAR(info->port.tty)) {
1080                 info->ignore_status_mask |= UART_LSR_PE | UART_LSR_FE;
1081                 info->read_status_mask |= UART_LSR_PE | UART_LSR_FE;
1082         }
1083 #endif
1084         if (I_IGNBRK(info->port.tty)) {
1085                 info->ignore_status_mask |= UART_LSR_BI;
1086                 info->read_status_mask |= UART_LSR_BI;
1087                 /*
1088                  * If we're ignore parity and break indicators, ignore
1089                  * overruns too.  (For real raw support).
1090                  */
1091                 if (I_IGNPAR(info->port.tty)) {
1092                         info->ignore_status_mask |= UART_LSR_OE | \
1093                                 UART_LSR_PE | UART_LSR_FE;
1094                         info->read_status_mask |= UART_LSR_OE | \
1095                                 UART_LSR_PE | UART_LSR_FE;
1096                 }
1097         }
1098
1099         if (I_IXOFF(info->port.tty))
1100                 flow1 |= 0x81;
1101
1102         spin_lock_irqsave(&info->lock, flags);
1103         /* set baud */
1104         serial_out(info, UART_ESI_CMD1, ESI_SET_BAUD);
1105         serial_out(info, UART_ESI_CMD2, quot >> 8);
1106         serial_out(info, UART_ESI_CMD2, quot & 0xff);
1107
1108         /* set data bits, parity, etc. */
1109         serial_out(info, UART_ESI_CMD1, ESI_WRITE_UART);
1110         serial_out(info, UART_ESI_CMD2, UART_LCR);
1111         serial_out(info, UART_ESI_CMD2, cval);
1112
1113         /* Enable flow control */
1114         serial_out(info, UART_ESI_CMD1, ESI_SET_FLOW_CNTL);
1115         serial_out(info, UART_ESI_CMD2, flow1);
1116         serial_out(info, UART_ESI_CMD2, flow2);
1117
1118         /* set flow control characters (XON/XOFF only) */
1119         if (I_IXOFF(info->port.tty)) {
1120                 serial_out(info, UART_ESI_CMD1, ESI_SET_FLOW_CHARS);
1121                 serial_out(info, UART_ESI_CMD2, START_CHAR(info->port.tty));
1122                 serial_out(info, UART_ESI_CMD2, STOP_CHAR(info->port.tty));
1123                 serial_out(info, UART_ESI_CMD2, 0x10);
1124                 serial_out(info, UART_ESI_CMD2, 0x21);
1125                 switch (cflag & CSIZE) {
1126                 case CS5:
1127                         serial_out(info, UART_ESI_CMD2, 0x1f);
1128                         break;
1129                 case CS6:
1130                         serial_out(info, UART_ESI_CMD2, 0x3f);
1131                         break;
1132                 case CS7:
1133                 case CS8:
1134                         serial_out(info, UART_ESI_CMD2, 0x7f);
1135                         break;
1136                 default:
1137                         serial_out(info, UART_ESI_CMD2, 0xff);
1138                         break;
1139                 }
1140         }
1141
1142         /* Set high/low water */
1143         serial_out(info, UART_ESI_CMD1, ESI_SET_FLOW_LVL);
1144         serial_out(info, UART_ESI_CMD2, info->config.flow_off >> 8);
1145         serial_out(info, UART_ESI_CMD2, info->config.flow_off);
1146         serial_out(info, UART_ESI_CMD2, info->config.flow_on >> 8);
1147         serial_out(info, UART_ESI_CMD2, info->config.flow_on);
1148
1149         spin_unlock_irqrestore(&info->lock, flags);
1150 }
1151
1152 static int rs_put_char(struct tty_struct *tty, unsigned char ch)
1153 {
1154         struct esp_struct *info = tty->driver_data;
1155         unsigned long flags;
1156         int ret = 0;
1157
1158         if (serial_paranoia_check(info, tty->name, "rs_put_char"))
1159                 return 0;
1160
1161         if (!info->xmit_buf)
1162                 return 0;
1163
1164         spin_lock_irqsave(&info->lock, flags);
1165         if (info->xmit_cnt < ESP_XMIT_SIZE - 1) {
1166                 info->xmit_buf[info->xmit_head++] = ch;
1167                 info->xmit_head &= ESP_XMIT_SIZE-1;
1168                 info->xmit_cnt++;
1169                 ret = 1;
1170         }
1171         spin_unlock_irqrestore(&info->lock, flags);
1172         return ret;
1173 }
1174
1175 static void rs_flush_chars(struct tty_struct *tty)
1176 {
1177         struct esp_struct *info = tty->driver_data;
1178         unsigned long flags;
1179
1180         if (serial_paranoia_check(info, tty->name, "rs_flush_chars"))
1181                 return;
1182
1183         spin_lock_irqsave(&info->lock, flags);
1184
1185         if (info->xmit_cnt <= 0 || tty->stopped || !info->xmit_buf)
1186                 goto out;
1187
1188         if (!(info->IER & UART_IER_THRI)) {
1189                 info->IER |= UART_IER_THRI;
1190                 serial_out(info, UART_ESI_CMD1, ESI_SET_SRV_MASK);
1191                 serial_out(info, UART_ESI_CMD2, info->IER);
1192         }
1193 out:
1194         spin_unlock_irqrestore(&info->lock, flags);
1195 }
1196
1197 static int rs_write(struct tty_struct *tty,
1198                     const unsigned char *buf, int count)
1199 {
1200         int     c, t, ret = 0;
1201         struct esp_struct *info = tty->driver_data;
1202         unsigned long flags;
1203
1204         if (serial_paranoia_check(info, tty->name, "rs_write"))
1205                 return 0;
1206
1207         if (!info->xmit_buf)
1208                 return 0;
1209
1210         while (1) {
1211                 /* Thanks to R. Wolff for suggesting how to do this with */
1212                 /* interrupts enabled */
1213
1214                 c = count;
1215                 t = ESP_XMIT_SIZE - info->xmit_cnt - 1;
1216
1217                 if (t < c)
1218                         c = t;
1219
1220                 t = ESP_XMIT_SIZE - info->xmit_head;
1221
1222                 if (t < c)
1223                         c = t;
1224
1225                 if (c <= 0)
1226                         break;
1227
1228                 memcpy(info->xmit_buf + info->xmit_head, buf, c);
1229
1230                 info->xmit_head = (info->xmit_head + c) & (ESP_XMIT_SIZE-1);
1231                 info->xmit_cnt += c;
1232                 buf += c;
1233                 count -= c;
1234                 ret += c;
1235         }
1236
1237         spin_lock_irqsave(&info->lock, flags);
1238
1239         if (info->xmit_cnt && !tty->stopped && !(info->IER & UART_IER_THRI)) {
1240                 info->IER |= UART_IER_THRI;
1241                 serial_out(info, UART_ESI_CMD1, ESI_SET_SRV_MASK);
1242                 serial_out(info, UART_ESI_CMD2, info->IER);
1243         }
1244
1245         spin_unlock_irqrestore(&info->lock, flags);
1246         return ret;
1247 }
1248
1249 static int rs_write_room(struct tty_struct *tty)
1250 {
1251         struct esp_struct *info = tty->driver_data;
1252         int     ret;
1253         unsigned long flags;
1254
1255         if (serial_paranoia_check(info, tty->name, "rs_write_room"))
1256                 return 0;
1257
1258         spin_lock_irqsave(&info->lock, flags);
1259
1260         ret = ESP_XMIT_SIZE - info->xmit_cnt - 1;
1261         if (ret < 0)
1262                 ret = 0;
1263         spin_unlock_irqrestore(&info->lock, flags);
1264         return ret;
1265 }
1266
1267 static int rs_chars_in_buffer(struct tty_struct *tty)
1268 {
1269         struct esp_struct *info = tty->driver_data;
1270
1271         if (serial_paranoia_check(info, tty->name, "rs_chars_in_buffer"))
1272                 return 0;
1273         return info->xmit_cnt;
1274 }
1275
1276 static void rs_flush_buffer(struct tty_struct *tty)
1277 {
1278         struct esp_struct *info = tty->driver_data;
1279         unsigned long flags;
1280
1281         if (serial_paranoia_check(info, tty->name, "rs_flush_buffer"))
1282                 return;
1283         spin_lock_irqsave(&info->lock, flags);
1284         info->xmit_cnt = info->xmit_head = info->xmit_tail = 0;
1285         spin_unlock_irqrestore(&info->lock, flags);
1286         tty_wakeup(tty);
1287 }
1288
1289 /*
1290  * ------------------------------------------------------------
1291  * rs_throttle()
1292  *
1293  * This routine is called by the upper-layer tty layer to signal that
1294  * incoming characters should be throttled.
1295  * ------------------------------------------------------------
1296  */
1297 static void rs_throttle(struct tty_struct *tty)
1298 {
1299         struct esp_struct *info = tty->driver_data;
1300         unsigned long flags;
1301 #ifdef SERIAL_DEBUG_THROTTLE
1302         char    buf[64];
1303
1304         printk("throttle %s: %d....\n", tty_name(tty, buf),
1305                                                 tty_chars_in_buffer(tty));
1306 #endif
1307
1308         if (serial_paranoia_check(info, tty->name, "rs_throttle"))
1309                 return;
1310
1311         spin_lock_irqsave(&info->lock, flags);
1312         info->IER &= ~UART_IER_RDI;
1313         serial_out(info, UART_ESI_CMD1, ESI_SET_SRV_MASK);
1314         serial_out(info, UART_ESI_CMD2, info->IER);
1315         serial_out(info, UART_ESI_CMD1, ESI_SET_RX_TIMEOUT);
1316         serial_out(info, UART_ESI_CMD2, 0x00);
1317         spin_unlock_irqrestore(&info->lock, flags);
1318 }
1319
1320 static void rs_unthrottle(struct tty_struct *tty)
1321 {
1322         struct esp_struct *info = tty->driver_data;
1323         unsigned long flags;
1324 #ifdef SERIAL_DEBUG_THROTTLE
1325         char    buf[64];
1326
1327         printk(KERN_DEBUG "unthrottle %s: %d....\n", tty_name(tty, buf),
1328                tty_chars_in_buffer(tty));
1329 #endif
1330
1331         if (serial_paranoia_check(info, tty->name, "rs_unthrottle"))
1332                 return;
1333
1334         spin_lock_irqsave(&info->lock, flags);
1335         info->IER |= UART_IER_RDI;
1336         serial_out(info, UART_ESI_CMD1, ESI_SET_SRV_MASK);
1337         serial_out(info, UART_ESI_CMD2, info->IER);
1338         serial_out(info, UART_ESI_CMD1, ESI_SET_RX_TIMEOUT);
1339         serial_out(info, UART_ESI_CMD2, info->config.rx_timeout);
1340         spin_unlock_irqrestore(&info->lock, flags);
1341 }
1342
1343 /*
1344  * ------------------------------------------------------------
1345  * rs_ioctl() and friends
1346  * ------------------------------------------------------------
1347  */
1348
1349 static int get_serial_info(struct esp_struct *info,
1350                            struct serial_struct __user *retinfo)
1351 {
1352         struct serial_struct tmp;
1353
1354         lock_kernel();
1355         memset(&tmp, 0, sizeof(tmp));
1356         tmp.type = PORT_16550A;
1357         tmp.line = info->line;
1358         tmp.port = info->io_port;
1359         tmp.irq = info->irq;
1360         tmp.flags = info->port.flags;
1361         tmp.xmit_fifo_size = 1024;
1362         tmp.baud_base = BASE_BAUD;
1363         tmp.close_delay = info->close_delay;
1364         tmp.closing_wait = info->closing_wait;
1365         tmp.custom_divisor = info->custom_divisor;
1366         tmp.hub6 = 0;
1367         unlock_kernel();
1368         if (copy_to_user(retinfo, &tmp, sizeof(*retinfo)))
1369                 return -EFAULT;
1370         return 0;
1371 }
1372
1373 static int get_esp_config(struct esp_struct *info,
1374                           struct hayes_esp_config __user *retinfo)
1375 {
1376         struct hayes_esp_config tmp;
1377
1378         if (!retinfo)
1379                 return -EFAULT;
1380
1381         memset(&tmp, 0, sizeof(tmp));
1382         lock_kernel();
1383         tmp.rx_timeout = info->config.rx_timeout;
1384         tmp.rx_trigger = info->config.rx_trigger;
1385         tmp.tx_trigger = info->config.tx_trigger;
1386         tmp.flow_off = info->config.flow_off;
1387         tmp.flow_on = info->config.flow_on;
1388         tmp.pio_threshold = info->config.pio_threshold;
1389         tmp.dma_channel = (info->stat_flags & ESP_STAT_NEVER_DMA ? 0 : dma);
1390         unlock_kernel();
1391
1392         return copy_to_user(retinfo, &tmp, sizeof(*retinfo)) ? -EFAULT : 0;
1393 }
1394
1395 static int set_serial_info(struct esp_struct *info,
1396                            struct serial_struct __user *new_info)
1397 {
1398         struct serial_struct new_serial;
1399         struct esp_struct old_info;
1400         unsigned int change_irq;
1401         int retval = 0;
1402         struct esp_struct *current_async;
1403
1404         if (copy_from_user(&new_serial, new_info, sizeof(new_serial)))
1405                 return -EFAULT;
1406         old_info = *info;
1407
1408         if ((new_serial.type != PORT_16550A) ||
1409             (new_serial.hub6) ||
1410             (info->io_port != new_serial.port) ||
1411             (new_serial.baud_base != BASE_BAUD) ||
1412             (new_serial.irq > 15) ||
1413             (new_serial.irq < 2) ||
1414             (new_serial.irq == 6) ||
1415             (new_serial.irq == 8) ||
1416             (new_serial.irq == 13))
1417                 return -EINVAL;
1418
1419         change_irq = new_serial.irq != info->irq;
1420
1421         if (change_irq && (info->line % 8))
1422                 return -EINVAL;
1423
1424         if (!capable(CAP_SYS_ADMIN)) {
1425                 if (change_irq ||
1426                     (new_serial.close_delay != info->close_delay) ||
1427                     ((new_serial.flags & ~ASYNC_USR_MASK) !=
1428                      (info->port.flags & ~ASYNC_USR_MASK)))
1429                         return -EPERM;
1430                 info->port.flags = ((info->port.flags & ~ASYNC_USR_MASK) |
1431                                (new_serial.flags & ASYNC_USR_MASK));
1432                 info->custom_divisor = new_serial.custom_divisor;
1433         } else {
1434                 if (new_serial.irq == 2)
1435                         new_serial.irq = 9;
1436
1437                 if (change_irq) {
1438                         current_async = ports;
1439
1440                         while (current_async) {
1441                                 if ((current_async->line >= info->line) &&
1442                                     (current_async->line < (info->line + 8))) {
1443                                         if (current_async == info) {
1444                                                 if (current_async->port.count > 1)
1445                                                         return -EBUSY;
1446                                         } else if (current_async->port.count)
1447                                                 return -EBUSY;
1448                                 }
1449
1450                                 current_async = current_async->next_port;
1451                         }
1452                 }
1453
1454                 /*
1455                  * OK, past this point, all the error checking has been done.
1456                  * At this point, we start making changes.....
1457                  */
1458
1459                 info->port.flags = ((info->port.flags & ~ASYNC_FLAGS) |
1460                                (new_serial.flags & ASYNC_FLAGS));
1461                 info->custom_divisor = new_serial.custom_divisor;
1462                 info->close_delay = new_serial.close_delay * HZ/100;
1463                 info->closing_wait = new_serial.closing_wait * HZ/100;
1464
1465                 if (change_irq) {
1466                         /*
1467                          * We need to shutdown the serial port at the old
1468                          * port/irq combination.
1469                          */
1470                         shutdown(info);
1471
1472                         current_async = ports;
1473
1474                         while (current_async) {
1475                                 if ((current_async->line >= info->line) &&
1476                                     (current_async->line < (info->line + 8)))
1477                                         current_async->irq = new_serial.irq;
1478
1479                                 current_async = current_async->next_port;
1480                         }
1481
1482                         serial_out(info, UART_ESI_CMD1, ESI_SET_ENH_IRQ);
1483                         if (info->irq == 9)
1484                                 serial_out(info, UART_ESI_CMD2, 0x02);
1485                         else
1486                                 serial_out(info, UART_ESI_CMD2, info->irq);
1487                 }
1488         }
1489
1490         if (info->port.flags & ASYNC_INITIALIZED) {
1491                 if (((old_info.port.flags & ASYNC_SPD_MASK) !=
1492                      (info->port.flags & ASYNC_SPD_MASK)) ||
1493                     (old_info.custom_divisor != info->custom_divisor)) {
1494                         if ((info->port.flags & ASYNC_SPD_MASK) == ASYNC_SPD_HI)
1495                                 info->port.tty->alt_speed = 57600;
1496                         if ((info->port.flags & ASYNC_SPD_MASK) == ASYNC_SPD_VHI)
1497                                 info->port.tty->alt_speed = 115200;
1498                         if ((info->port.flags & ASYNC_SPD_MASK) == ASYNC_SPD_SHI)
1499                                 info->port.tty->alt_speed = 230400;
1500                         if ((info->port.flags & ASYNC_SPD_MASK) == ASYNC_SPD_WARP)
1501                                 info->port.tty->alt_speed = 460800;
1502                         change_speed(info);
1503                 }
1504         } else
1505                 retval = startup(info);
1506
1507         return retval;
1508 }
1509
1510 static int set_esp_config(struct esp_struct *info,
1511                           struct hayes_esp_config __user *new_info)
1512 {
1513         struct hayes_esp_config new_config;
1514         unsigned int change_dma;
1515         int retval = 0;
1516         struct esp_struct *current_async;
1517         unsigned long flags;
1518
1519         /* Perhaps a non-sysadmin user should be able to do some of these */
1520         /* operations.  I haven't decided yet. */
1521
1522         if (!capable(CAP_SYS_ADMIN))
1523                 return -EPERM;
1524
1525         if (copy_from_user(&new_config, new_info, sizeof(new_config)))
1526                 return -EFAULT;
1527
1528         if ((new_config.flow_on >= new_config.flow_off) ||
1529             (new_config.rx_trigger < 1) ||
1530             (new_config.tx_trigger < 1) ||
1531             (new_config.flow_off < 1) ||
1532             (new_config.flow_on < 1) ||
1533             (new_config.rx_trigger > 1023) ||
1534             (new_config.tx_trigger > 1023) ||
1535             (new_config.flow_off > 1023) ||
1536             (new_config.flow_on > 1023) ||
1537             (new_config.pio_threshold < 0) ||
1538             (new_config.pio_threshold > 1024))
1539                 return -EINVAL;
1540
1541         if ((new_config.dma_channel != 1) && (new_config.dma_channel != 3))
1542                 new_config.dma_channel = 0;
1543
1544         if (info->stat_flags & ESP_STAT_NEVER_DMA)
1545                 change_dma = new_config.dma_channel;
1546         else
1547                 change_dma = (new_config.dma_channel != dma);
1548
1549         if (change_dma) {
1550                 if (new_config.dma_channel) {
1551                         /* PIO mode to DMA mode transition OR */
1552                         /* change current DMA channel */
1553                         current_async = ports;
1554
1555                         while (current_async) {
1556                                 if (current_async == info) {
1557                                         if (current_async->port.count > 1)
1558                                                 return -EBUSY;
1559                                 } else if (current_async->port.count)
1560                                         return -EBUSY;
1561
1562                                 current_async = current_async->next_port;
1563                         }
1564
1565                         shutdown(info);
1566                         dma = new_config.dma_channel;
1567                         info->stat_flags &= ~ESP_STAT_NEVER_DMA;
1568
1569                         /* all ports must use the same DMA channel */
1570
1571                         spin_lock_irqsave(&info->lock, flags);
1572                         current_async = ports;
1573
1574                         while (current_async) {
1575                                 esp_basic_init(current_async);
1576                                 current_async = current_async->next_port;
1577                         }
1578                         spin_unlock_irqrestore(&info->lock, flags);
1579                 } else {
1580                         /* DMA mode to PIO mode only */
1581                         if (info->port.count > 1)
1582                                 return -EBUSY;
1583
1584                         shutdown(info);
1585                         spin_lock_irqsave(&info->lock, flags);
1586                         info->stat_flags |= ESP_STAT_NEVER_DMA;
1587                         esp_basic_init(info);
1588                         spin_unlock_irqrestore(&info->lock, flags);
1589                 }
1590         }
1591
1592         info->config.pio_threshold = new_config.pio_threshold;
1593
1594         if ((new_config.flow_off != info->config.flow_off) ||
1595             (new_config.flow_on != info->config.flow_on)) {
1596                 info->config.flow_off = new_config.flow_off;
1597                 info->config.flow_on = new_config.flow_on;
1598
1599                 spin_lock_irqsave(&info->lock, flags);
1600                 serial_out(info, UART_ESI_CMD1, ESI_SET_FLOW_LVL);
1601                 serial_out(info, UART_ESI_CMD2, new_config.flow_off >> 8);
1602                 serial_out(info, UART_ESI_CMD2, new_config.flow_off);
1603                 serial_out(info, UART_ESI_CMD2, new_config.flow_on >> 8);
1604                 serial_out(info, UART_ESI_CMD2, new_config.flow_on);
1605                 spin_unlock_irqrestore(&info->lock, flags);
1606         }
1607
1608         if ((new_config.rx_trigger != info->config.rx_trigger) ||
1609             (new_config.tx_trigger != info->config.tx_trigger)) {
1610                 info->config.rx_trigger = new_config.rx_trigger;
1611                 info->config.tx_trigger = new_config.tx_trigger;
1612                 spin_lock_irqsave(&info->lock, flags);
1613                 serial_out(info, UART_ESI_CMD1, ESI_SET_TRIGGER);
1614                 serial_out(info, UART_ESI_CMD2,
1615                            new_config.rx_trigger >> 8);
1616                 serial_out(info, UART_ESI_CMD2, new_config.rx_trigger);
1617                 serial_out(info, UART_ESI_CMD2,
1618                            new_config.tx_trigger >> 8);
1619                 serial_out(info, UART_ESI_CMD2, new_config.tx_trigger);
1620                 spin_unlock_irqrestore(&info->lock, flags);
1621         }
1622
1623         if (new_config.rx_timeout != info->config.rx_timeout) {
1624                 info->config.rx_timeout = new_config.rx_timeout;
1625                 spin_lock_irqsave(&info->lock, flags);
1626
1627                 if (info->IER & UART_IER_RDI) {
1628                         serial_out(info, UART_ESI_CMD1,
1629                                    ESI_SET_RX_TIMEOUT);
1630                         serial_out(info, UART_ESI_CMD2,
1631                                    new_config.rx_timeout);
1632                 }
1633
1634                 spin_unlock_irqrestore(&info->lock, flags);
1635         }
1636
1637         if (!(info->port.flags & ASYNC_INITIALIZED))
1638                 retval = startup(info);
1639
1640         return retval;
1641 }
1642
1643 /*
1644  * get_lsr_info - get line status register info
1645  *
1646  * Purpose: Let user call ioctl() to get info when the UART physically
1647  *          is emptied.  On bus types like RS485, the transmitter must
1648  *          release the bus after transmitting. This must be done when
1649  *          the transmit shift register is empty, not be done when the
1650  *          transmit holding register is empty.  This functionality
1651  *          allows an RS485 driver to be written in user space.
1652  */
1653 static int get_lsr_info(struct esp_struct *info, unsigned int __user *value)
1654 {
1655         unsigned char status;
1656         unsigned int result;
1657         unsigned long flags;
1658
1659         spin_lock_irqsave(&info->lock, flags);
1660         serial_out(info, UART_ESI_CMD1, ESI_GET_UART_STAT);
1661         status = serial_in(info, UART_ESI_STAT1);
1662         spin_unlock_irqrestore(&info->lock, flags);
1663         result = ((status & UART_LSR_TEMT) ? TIOCSER_TEMT : 0);
1664         return put_user(result, value);
1665 }
1666
1667
1668 static int esp_tiocmget(struct tty_struct *tty, struct file *file)
1669 {
1670         struct esp_struct *info = tty->driver_data;
1671         unsigned char control, status;
1672         unsigned long flags;
1673
1674         if (serial_paranoia_check(info, tty->name, __func__))
1675                 return -ENODEV;
1676         if (tty->flags & (1 << TTY_IO_ERROR))
1677                 return -EIO;
1678
1679         control = info->MCR;
1680
1681         spin_lock_irqsave(&info->lock, flags);
1682         serial_out(info, UART_ESI_CMD1, ESI_GET_UART_STAT);
1683         status = serial_in(info, UART_ESI_STAT2);
1684         spin_unlock_irqrestore(&info->lock, flags);
1685
1686         return    ((control & UART_MCR_RTS) ? TIOCM_RTS : 0)
1687                 | ((control & UART_MCR_DTR) ? TIOCM_DTR : 0)
1688                 | ((status  & UART_MSR_DCD) ? TIOCM_CAR : 0)
1689                 | ((status  & UART_MSR_RI) ? TIOCM_RNG : 0)
1690                 | ((status  & UART_MSR_DSR) ? TIOCM_DSR : 0)
1691                 | ((status  & UART_MSR_CTS) ? TIOCM_CTS : 0);
1692 }
1693
1694 static int esp_tiocmset(struct tty_struct *tty, struct file *file,
1695                         unsigned int set, unsigned int clear)
1696 {
1697         struct esp_struct *info = tty->driver_data;
1698         unsigned long flags;
1699
1700         if (serial_paranoia_check(info, tty->name, __func__))
1701                 return -ENODEV;
1702         if (tty->flags & (1 << TTY_IO_ERROR))
1703                 return -EIO;
1704
1705         spin_lock_irqsave(&info->lock, flags);
1706
1707         if (set & TIOCM_RTS)
1708                 info->MCR |= UART_MCR_RTS;
1709         if (set & TIOCM_DTR)
1710                 info->MCR |= UART_MCR_DTR;
1711
1712         if (clear & TIOCM_RTS)
1713                 info->MCR &= ~UART_MCR_RTS;
1714         if (clear & TIOCM_DTR)
1715                 info->MCR &= ~UART_MCR_DTR;
1716
1717         serial_out(info, UART_ESI_CMD1, ESI_WRITE_UART);
1718         serial_out(info, UART_ESI_CMD2, UART_MCR);
1719         serial_out(info, UART_ESI_CMD2, info->MCR);
1720
1721         spin_unlock_irqrestore(&info->lock, flags);
1722         return 0;
1723 }
1724
1725 /*
1726  * rs_break() --- routine which turns the break handling on or off
1727  */
1728 static int esp_break(struct tty_struct *tty, int break_state)
1729 {
1730         struct esp_struct *info = tty->driver_data;
1731         unsigned long flags;
1732
1733         if (serial_paranoia_check(info, tty->name, "esp_break"))
1734                 return -EINVAL;
1735
1736         if (break_state == -1) {
1737                 spin_lock_irqsave(&info->lock, flags);
1738                 serial_out(info, UART_ESI_CMD1, ESI_ISSUE_BREAK);
1739                 serial_out(info, UART_ESI_CMD2, 0x01);
1740                 spin_unlock_irqrestore(&info->lock, flags);
1741
1742                 /* FIXME - new style wait needed here */
1743                 interruptible_sleep_on(&info->break_wait);
1744         } else {
1745                 spin_lock_irqsave(&info->lock, flags);
1746                 serial_out(info, UART_ESI_CMD1, ESI_ISSUE_BREAK);
1747                 serial_out(info, UART_ESI_CMD2, 0x00);
1748                 spin_unlock_irqrestore(&info->lock, flags);
1749         }
1750         return 0;
1751 }
1752
1753 static int rs_ioctl(struct tty_struct *tty, struct file *file,
1754                     unsigned int cmd, unsigned long arg)
1755 {
1756         struct esp_struct *info = tty->driver_data;
1757         struct async_icount cprev, cnow;        /* kernel counter temps */
1758         struct serial_icounter_struct __user *p_cuser;  /* user space */
1759         void __user *argp = (void __user *)arg;
1760         unsigned long flags;
1761         int ret;
1762
1763         if (serial_paranoia_check(info, tty->name, "rs_ioctl"))
1764                 return -ENODEV;
1765
1766         if ((cmd != TIOCGSERIAL) && (cmd != TIOCSSERIAL) &&
1767             (cmd != TIOCSERCONFIG) && (cmd != TIOCSERGWILD)  &&
1768             (cmd != TIOCSERSWILD) && (cmd != TIOCSERGSTRUCT) &&
1769             (cmd != TIOCMIWAIT) && (cmd != TIOCGICOUNT) &&
1770             (cmd != TIOCGHAYESESP) && (cmd != TIOCSHAYESESP)) {
1771                 if (tty->flags & (1 << TTY_IO_ERROR))
1772                     return -EIO;
1773         }
1774
1775         switch (cmd) {
1776         case TIOCGSERIAL:
1777                 return get_serial_info(info, argp);
1778         case TIOCSSERIAL:
1779                 lock_kernel();
1780                 ret = set_serial_info(info, argp);
1781                 unlock_kernel();
1782                 return ret;
1783         case TIOCSERGWILD:
1784                 return put_user(0L, (unsigned long __user *)argp);
1785         case TIOCSERGETLSR: /* Get line status register */
1786                 return get_lsr_info(info, argp);
1787         case TIOCSERSWILD:
1788                 if (!capable(CAP_SYS_ADMIN))
1789                         return -EPERM;
1790                 return 0;
1791         /*
1792          * Wait for any of the 4 modem inputs (DCD,RI,DSR,CTS) to change
1793          * - mask passed in arg for lines of interest
1794          *   (use |'ed TIOCM_RNG/DSR/CD/CTS for masking)
1795          * Caller should use TIOCGICOUNT to see which one it was
1796          */
1797         case TIOCMIWAIT:
1798                 spin_lock_irqsave(&info->lock, flags);
1799                 cprev = info->icount;   /* note the counters on entry */
1800                 spin_unlock_irqrestore(&info->lock, flags);
1801                 while (1) {
1802                         /* FIXME: convert to new style wakeup */
1803                         interruptible_sleep_on(&info->delta_msr_wait);
1804                         /* see if a signal did it */
1805                         if (signal_pending(current))
1806                                 return -ERESTARTSYS;
1807                         spin_lock_irqsave(&info->lock, flags);
1808                         cnow = info->icount;    /* atomic copy */
1809                         spin_unlock_irqrestore(&info->lock, flags);
1810                         if (cnow.rng == cprev.rng &&
1811                             cnow.dsr == cprev.dsr &&
1812                             cnow.dcd == cprev.dcd &&
1813                             cnow.cts == cprev.cts)
1814                                 return -EIO; /* no change => error */
1815                         if (((arg & TIOCM_RNG) &&
1816                              (cnow.rng != cprev.rng)) ||
1817                              ((arg & TIOCM_DSR) &&
1818                               (cnow.dsr != cprev.dsr)) ||
1819                              ((arg & TIOCM_CD) &&
1820                               (cnow.dcd != cprev.dcd)) ||
1821                              ((arg & TIOCM_CTS) &&
1822                               (cnow.cts != cprev.cts))) {
1823                                 return 0;
1824                         }
1825                         cprev = cnow;
1826                 }
1827                 /* NOTREACHED */
1828         /*
1829          * Get counter of input serial line interrupts (DCD,RI,DSR,CTS)
1830          * Return: write counters to the user passed counter struct
1831          * NB: both 1->0 and 0->1 transitions are counted except for
1832          *     RI where only 0->1 is counted.
1833          */
1834         case TIOCGICOUNT:
1835                 spin_lock_irqsave(&info->lock, flags);
1836                 cnow = info->icount;
1837                 spin_unlock_irqrestore(&info->lock, flags);
1838                 p_cuser = argp;
1839                 if (put_user(cnow.cts, &p_cuser->cts) ||
1840                     put_user(cnow.dsr, &p_cuser->dsr) ||
1841                     put_user(cnow.rng, &p_cuser->rng) ||
1842                     put_user(cnow.dcd, &p_cuser->dcd))
1843                         return -EFAULT;
1844                         return 0;
1845         case TIOCGHAYESESP:
1846                 return get_esp_config(info, argp);
1847         case TIOCSHAYESESP:
1848                 lock_kernel();
1849                 ret = set_esp_config(info, argp);
1850                 unlock_kernel();
1851                 return ret;
1852         default:
1853                 return -ENOIOCTLCMD;
1854         }
1855         return 0;
1856 }
1857
1858 static void rs_set_termios(struct tty_struct *tty, struct ktermios *old_termios)
1859 {
1860         struct esp_struct *info = tty->driver_data;
1861         unsigned long flags;
1862
1863         change_speed(info);
1864
1865         spin_lock_irqsave(&info->lock, flags);
1866
1867         /* Handle transition to B0 status */
1868         if ((old_termios->c_cflag & CBAUD) &&
1869                 !(tty->termios->c_cflag & CBAUD)) {
1870                 info->MCR &= ~(UART_MCR_DTR|UART_MCR_RTS);
1871                 serial_out(info, UART_ESI_CMD1, ESI_WRITE_UART);
1872                 serial_out(info, UART_ESI_CMD2, UART_MCR);
1873                 serial_out(info, UART_ESI_CMD2, info->MCR);
1874         }
1875
1876         /* Handle transition away from B0 status */
1877         if (!(old_termios->c_cflag & CBAUD) &&
1878                 (tty->termios->c_cflag & CBAUD)) {
1879                 info->MCR |= (UART_MCR_DTR | UART_MCR_RTS);
1880                 serial_out(info, UART_ESI_CMD1, ESI_WRITE_UART);
1881                 serial_out(info, UART_ESI_CMD2, UART_MCR);
1882                 serial_out(info, UART_ESI_CMD2, info->MCR);
1883         }
1884
1885         spin_unlock_irqrestore(&info->lock, flags);
1886
1887         /* Handle turning of CRTSCTS */
1888         if ((old_termios->c_cflag & CRTSCTS) &&
1889             !(tty->termios->c_cflag & CRTSCTS)) {
1890                 rs_start(tty);
1891         }
1892 }
1893
1894 /*
1895  * ------------------------------------------------------------
1896  * rs_close()
1897  *
1898  * This routine is called when the serial port gets closed.  First, we
1899  * wait for the last remaining data to be sent.  Then, we unlink its
1900  * async structure from the interrupt chain if necessary, and we free
1901  * that IRQ if nothing is left in the chain.
1902  * ------------------------------------------------------------
1903  */
1904 static void rs_close(struct tty_struct *tty, struct file *filp)
1905 {
1906         struct esp_struct *info = tty->driver_data;
1907         unsigned long flags;
1908
1909         if (!info || serial_paranoia_check(info, tty->name, "rs_close"))
1910                 return;
1911
1912         spin_lock_irqsave(&info->lock, flags);
1913
1914         if (tty_hung_up_p(filp)) {
1915                 DBG_CNT("before DEC-hung");
1916                 goto out;
1917         }
1918
1919 #ifdef SERIAL_DEBUG_OPEN
1920         printk(KERN_DEBUG "rs_close ttys%d, count = %d\n",
1921                                                 info->line, info->port.count);
1922 #endif
1923         if (tty->count == 1 && info->port.count != 1) {
1924                 /*
1925                  * Uh, oh.  tty->count is 1, which means that the tty
1926                  * structure will be freed.  Info->count should always
1927                  * be one in these conditions.  If it's greater than
1928                  * one, we've got real problems, since it means the
1929                  * serial port won't be shutdown.
1930                  */
1931                 printk(KERN_DEBUG "rs_close: bad serial port count; tty->count is 1, info->port.count is %d\n", info->port.count);
1932                 info->port.count = 1;
1933         }
1934         if (--info->port.count < 0) {
1935                 printk(KERN_ERR "rs_close: bad serial port count for ttys%d: %d\n",
1936                        info->line, info->port.count);
1937                 info->port.count = 0;
1938         }
1939         if (info->port.count) {
1940                 DBG_CNT("before DEC-2");
1941                 goto out;
1942         }
1943         info->port.flags |= ASYNC_CLOSING;
1944
1945         spin_unlock_irqrestore(&info->lock, flags);
1946         /*
1947          * Now we wait for the transmit buffer to clear; and we notify
1948          * the line discipline to only process XON/XOFF characters.
1949          */
1950         tty->closing = 1;
1951         if (info->closing_wait != ASYNC_CLOSING_WAIT_NONE)
1952                 tty_wait_until_sent(tty, info->closing_wait);
1953         /*
1954          * At this point we stop accepting input.  To do this, we
1955          * disable the receive line status interrupts, and tell the
1956          * interrupt driver to stop checking the data ready bit in the
1957          * line status register.
1958          */
1959         /* info->IER &= ~UART_IER_RLSI; */
1960         info->IER &= ~UART_IER_RDI;
1961         info->read_status_mask &= ~UART_LSR_DR;
1962         if (info->port.flags & ASYNC_INITIALIZED) {
1963
1964                 spin_lock_irqsave(&info->lock, flags);
1965                 serial_out(info, UART_ESI_CMD1, ESI_SET_SRV_MASK);
1966                 serial_out(info, UART_ESI_CMD2, info->IER);
1967
1968                 /* disable receive timeout */
1969                 serial_out(info, UART_ESI_CMD1, ESI_SET_RX_TIMEOUT);
1970                 serial_out(info, UART_ESI_CMD2, 0x00);
1971
1972                 spin_unlock_irqrestore(&info->lock, flags);
1973
1974                 /*
1975                  * Before we drop DTR, make sure the UART transmitter
1976                  * has completely drained; this is especially
1977                  * important if there is a transmit FIFO!
1978                  */
1979                 rs_wait_until_sent(tty, info->timeout);
1980         }
1981         shutdown(info);
1982         rs_flush_buffer(tty);
1983         tty_ldisc_flush(tty);
1984         tty->closing = 0;
1985         info->port.tty = NULL;
1986
1987         if (info->port.blocked_open) {
1988                 if (info->close_delay)
1989                         msleep_interruptible(jiffies_to_msecs(info->close_delay));
1990                 wake_up_interruptible(&info->port.open_wait);
1991         }
1992         info->port.flags &= ~(ASYNC_NORMAL_ACTIVE|ASYNC_CLOSING);
1993         wake_up_interruptible(&info->port.close_wait);
1994         return;
1995
1996 out:
1997         spin_unlock_irqrestore(&info->lock, flags);
1998 }
1999
2000 static void rs_wait_until_sent(struct tty_struct *tty, int timeout)
2001 {
2002         struct esp_struct *info = tty->driver_data;
2003         unsigned long orig_jiffies, char_time;
2004         unsigned long flags;
2005
2006         if (serial_paranoia_check(info, tty->name, "rs_wait_until_sent"))
2007                 return;
2008
2009         orig_jiffies = jiffies;
2010         char_time = ((info->timeout - HZ / 50) / 1024) / 5;
2011
2012         if (!char_time)
2013                 char_time = 1;
2014
2015         spin_lock_irqsave(&info->lock, flags);
2016         serial_out(info, UART_ESI_CMD1, ESI_NO_COMMAND);
2017         serial_out(info, UART_ESI_CMD1, ESI_GET_TX_AVAIL);
2018
2019         while ((serial_in(info, UART_ESI_STAT1) != 0x03) ||
2020                 (serial_in(info, UART_ESI_STAT2) != 0xff)) {
2021
2022                 spin_unlock_irqrestore(&info->lock, flags);
2023                 msleep_interruptible(jiffies_to_msecs(char_time));
2024
2025                 if (signal_pending(current))
2026                         return;
2027
2028                 if (timeout && time_after(jiffies, orig_jiffies + timeout))
2029                         return;
2030
2031                 spin_lock_irqsave(&info->lock, flags);
2032                 serial_out(info, UART_ESI_CMD1, ESI_NO_COMMAND);
2033                 serial_out(info, UART_ESI_CMD1, ESI_GET_TX_AVAIL);
2034         }
2035         spin_unlock_irqrestore(&info->lock, flags);
2036         set_current_state(TASK_RUNNING);
2037 }
2038
2039 /*
2040  * esp_hangup() --- called by tty_hangup() when a hangup is signaled.
2041  */
2042 static void esp_hangup(struct tty_struct *tty)
2043 {
2044         struct esp_struct *info = tty->driver_data;
2045
2046         if (serial_paranoia_check(info, tty->name, "esp_hangup"))
2047                 return;
2048
2049         rs_flush_buffer(tty);
2050         shutdown(info);
2051         info->port.count = 0;
2052         info->port.flags &= ~ASYNC_NORMAL_ACTIVE;
2053         info->port.tty = NULL;
2054         wake_up_interruptible(&info->port.open_wait);
2055 }
2056
2057 static int esp_carrier_raised(struct tty_port *port)
2058 {
2059         struct esp_struct *info = container_of(port, struct esp_struct, port);
2060         serial_out(info, UART_ESI_CMD1, ESI_GET_UART_STAT);
2061         if (serial_in(info, UART_ESI_STAT2) & UART_MSR_DCD)
2062                 return 1;
2063         return 0;
2064 }
2065
2066 /*
2067  * ------------------------------------------------------------
2068  * esp_open() and friends
2069  * ------------------------------------------------------------
2070  */
2071 static int block_til_ready(struct tty_struct *tty, struct file *filp,
2072                            struct esp_struct *info)
2073 {
2074         DECLARE_WAITQUEUE(wait, current);
2075         int             retval;
2076         int             do_clocal = 0;
2077         unsigned long   flags;
2078         int             cd;
2079         struct tty_port *port = &info->port;
2080
2081         /*
2082          * If the device is in the middle of being closed, then block
2083          * until it's done, and then try again.
2084          */
2085         if (tty_hung_up_p(filp) ||
2086             (port->flags & ASYNC_CLOSING)) {
2087                 if (port->flags & ASYNC_CLOSING)
2088                         interruptible_sleep_on(&port->close_wait);
2089 #ifdef SERIAL_DO_RESTART
2090                 if (port->flags & ASYNC_HUP_NOTIFY)
2091                         return -EAGAIN;
2092                 else
2093                         return -ERESTARTSYS;
2094 #else
2095                 return -EAGAIN;
2096 #endif
2097         }
2098
2099         /*
2100          * If non-blocking mode is set, or the port is not enabled,
2101          * then make the check up front and then exit.
2102          */
2103         if ((filp->f_flags & O_NONBLOCK) ||
2104             (tty->flags & (1 << TTY_IO_ERROR))) {
2105                 port->flags |= ASYNC_NORMAL_ACTIVE;
2106                 return 0;
2107         }
2108
2109         if (tty->termios->c_cflag & CLOCAL)
2110                 do_clocal = 1;
2111
2112         /*
2113          * Block waiting for the carrier detect and the line to become
2114          * free (i.e., not in use by the callout).  While we are in
2115          * this loop, port->count is dropped by one, so that
2116          * rs_close() knows when to free things.  We restore it upon
2117          * exit, either normal or abnormal.
2118          */
2119         retval = 0;
2120         add_wait_queue(&port->open_wait, &wait);
2121 #ifdef SERIAL_DEBUG_OPEN
2122         printk(KERN_DEBUG "block_til_ready before block: ttys%d, count = %d\n",
2123                info->line, port->count);
2124 #endif
2125         spin_lock_irqsave(&info->lock, flags);
2126         if (!tty_hung_up_p(filp))
2127                 port->count--;
2128         port->blocked_open++;
2129         while (1) {
2130                 if ((tty->termios->c_cflag & CBAUD)) {
2131                         unsigned int scratch;
2132
2133                         serial_out(info, UART_ESI_CMD1, ESI_READ_UART);
2134                         serial_out(info, UART_ESI_CMD2, UART_MCR);
2135                         scratch = serial_in(info, UART_ESI_STAT1);
2136                         serial_out(info, UART_ESI_CMD1, ESI_WRITE_UART);
2137                         serial_out(info, UART_ESI_CMD2, UART_MCR);
2138                         serial_out(info, UART_ESI_CMD2,
2139                                 scratch | UART_MCR_DTR | UART_MCR_RTS);
2140                 }
2141                 set_current_state(TASK_INTERRUPTIBLE);
2142                 if (tty_hung_up_p(filp) ||
2143                     !(port->flags & ASYNC_INITIALIZED)) {
2144 #ifdef SERIAL_DO_RESTART
2145                         if (port->flags & ASYNC_HUP_NOTIFY)
2146                                 retval = -EAGAIN;
2147                         else
2148                                 retval = -ERESTARTSYS;
2149 #else
2150                         retval = -EAGAIN;
2151 #endif
2152                         break;
2153                 }
2154
2155                 cd = tty_port_carrier_raised(port);
2156
2157                 if (!(port->flags & ASYNC_CLOSING) &&
2158                     (do_clocal))
2159                         break;
2160                 if (signal_pending(current)) {
2161                         retval = -ERESTARTSYS;
2162                         break;
2163                 }
2164 #ifdef SERIAL_DEBUG_OPEN
2165                 printk(KERN_DEBUG "block_til_ready blocking: ttys%d, count = %d\n",
2166                        info->line, port->count);
2167 #endif
2168                 spin_unlock_irqrestore(&info->lock, flags);
2169                 schedule();
2170                 spin_lock_irqsave(&info->lock, flags);
2171         }
2172         set_current_state(TASK_RUNNING);
2173         remove_wait_queue(&port->open_wait, &wait);
2174         if (!tty_hung_up_p(filp))
2175                 port->count++;
2176         port->blocked_open--;
2177         spin_unlock_irqrestore(&info->lock, flags);
2178 #ifdef SERIAL_DEBUG_OPEN
2179         printk(KERN_DEBUG "block_til_ready after blocking: ttys%d, count = %d\n",
2180                info->line, port->count);
2181 #endif
2182         if (retval)
2183                 return retval;
2184         port->flags |= ASYNC_NORMAL_ACTIVE;
2185         return 0;
2186 }
2187
2188 /*
2189  * This routine is called whenever a serial port is opened.  It
2190  * enables interrupts for a serial port, linking in its async structure into
2191  * the IRQ chain.   It also performs the serial-specific
2192  * initialization for the tty structure.
2193  */
2194 static int esp_open(struct tty_struct *tty, struct file *filp)
2195 {
2196         struct esp_struct       *info;
2197         int                     retval, line;
2198         unsigned long           flags;
2199
2200         line = tty->index;
2201         if ((line < 0) || (line >= NR_PORTS))
2202                 return -ENODEV;
2203
2204         /* find the port in the chain */
2205
2206         info = ports;
2207
2208         while (info && (info->line != line))
2209                 info = info->next_port;
2210
2211         if (!info) {
2212                 serial_paranoia_check(info, tty->name, "esp_open");
2213                 return -ENODEV;
2214         }
2215
2216 #ifdef SERIAL_DEBUG_OPEN
2217         printk(KERN_DEBUG "esp_open %s, count = %d\n", tty->name, info->port.count);
2218 #endif
2219         spin_lock_irqsave(&info->lock, flags);
2220         info->port.count++;
2221         tty->driver_data = info;
2222         info->port.tty = tty;
2223
2224         spin_unlock_irqrestore(&info->lock, flags);
2225
2226         /*
2227          * Start up serial port
2228          */
2229         retval = startup(info);
2230         if (retval)
2231                 return retval;
2232
2233         retval = block_til_ready(tty, filp, info);
2234         if (retval) {
2235 #ifdef SERIAL_DEBUG_OPEN
2236                 printk(KERN_DEBUG "esp_open returning after block_til_ready with %d\n",
2237                        retval);
2238 #endif
2239                 return retval;
2240         }
2241 #ifdef SERIAL_DEBUG_OPEN
2242         printk(KERN_DEBUG "esp_open %s successful...", tty->name);
2243 #endif
2244         return 0;
2245 }
2246
2247 /*
2248  * ---------------------------------------------------------------------
2249  * espserial_init() and friends
2250  *
2251  * espserial_init() is called at boot-time to initialize the serial driver.
2252  * ---------------------------------------------------------------------
2253  */
2254
2255 /*
2256  * This routine prints out the appropriate serial driver version
2257  * number, and identifies which options were configured into this
2258  * driver.
2259  */
2260
2261 static void __init show_serial_version(void)
2262 {
2263         printk(KERN_INFO "%s version %s (DMA %u)\n",
2264                 serial_name, serial_version, dma);
2265 }
2266
2267 /*
2268  * This routine is called by espserial_init() to initialize a specific serial
2269  * port.
2270  */
2271 static int autoconfig(struct esp_struct *info)
2272 {
2273         int port_detected = 0;
2274         unsigned long flags;
2275
2276         if (!request_region(info->io_port, REGION_SIZE, "esp serial"))
2277                 return -EIO;
2278
2279         spin_lock_irqsave(&info->lock, flags);
2280         /*
2281          * Check for ESP card
2282          */
2283
2284         if (serial_in(info, UART_ESI_BASE) == 0xf3) {
2285                 serial_out(info, UART_ESI_CMD1, 0x00);
2286                 serial_out(info, UART_ESI_CMD1, 0x01);
2287
2288                 if ((serial_in(info, UART_ESI_STAT2) & 0x70) == 0x20) {
2289                         port_detected = 1;
2290
2291                         if (!(info->irq)) {
2292                                 serial_out(info, UART_ESI_CMD1, 0x02);
2293
2294                                 if (serial_in(info, UART_ESI_STAT1) & 0x01)
2295                                         info->irq = 3;
2296                                 else
2297                                         info->irq = 4;
2298                         }
2299
2300
2301                         /* put card in enhanced mode */
2302                         /* this prevents access through */
2303                         /* the "old" IO ports */
2304                         esp_basic_init(info);
2305
2306                         /* clear out MCR */
2307                         serial_out(info, UART_ESI_CMD1, ESI_WRITE_UART);
2308                         serial_out(info, UART_ESI_CMD2, UART_MCR);
2309                         serial_out(info, UART_ESI_CMD2, 0x00);
2310                 }
2311         }
2312         if (!port_detected)
2313                 release_region(info->io_port, REGION_SIZE);
2314
2315         spin_unlock_irqrestore(&info->lock, flags);
2316         return (port_detected);
2317 }
2318
2319 static const struct tty_operations esp_ops = {
2320         .open = esp_open,
2321         .close = rs_close,
2322         .write = rs_write,
2323         .put_char = rs_put_char,
2324         .flush_chars = rs_flush_chars,
2325         .write_room = rs_write_room,
2326         .chars_in_buffer = rs_chars_in_buffer,
2327         .flush_buffer = rs_flush_buffer,
2328         .ioctl = rs_ioctl,
2329         .throttle = rs_throttle,
2330         .unthrottle = rs_unthrottle,
2331         .set_termios = rs_set_termios,
2332         .stop = rs_stop,
2333         .start = rs_start,
2334         .hangup = esp_hangup,
2335         .break_ctl = esp_break,
2336         .wait_until_sent = rs_wait_until_sent,
2337         .tiocmget = esp_tiocmget,
2338         .tiocmset = esp_tiocmset,
2339 };
2340
2341 static const struct tty_port_operations esp_port_ops = {
2342         .esp_carrier_raised,
2343 };
2344
2345 /*
2346  * The serial driver boot-time initialization code!
2347  */
2348 static int __init espserial_init(void)
2349 {
2350         int i, offset;
2351         struct esp_struct *info;
2352         struct esp_struct *last_primary = NULL;
2353         int esp[] = { 0x100, 0x140, 0x180, 0x200, 0x240, 0x280, 0x300, 0x380 };
2354
2355         esp_driver = alloc_tty_driver(NR_PORTS);
2356         if (!esp_driver)
2357                 return -ENOMEM;
2358
2359         for (i = 0; i < NR_PRIMARY; i++) {
2360                 if (irq[i] != 0) {
2361                         if ((irq[i] < 2) || (irq[i] > 15) || (irq[i] == 6) ||
2362                             (irq[i] == 8) || (irq[i] == 13))
2363                                 irq[i] = 0;
2364                         else if (irq[i] == 2)
2365                                 irq[i] = 9;
2366                 }
2367         }
2368
2369         if ((dma != 1) && (dma != 3))
2370                 dma = 0;
2371
2372         if ((rx_trigger < 1) || (rx_trigger > 1023))
2373                 rx_trigger = 768;
2374
2375         if ((tx_trigger < 1) || (tx_trigger > 1023))
2376                 tx_trigger = 768;
2377
2378         if ((flow_off < 1) || (flow_off > 1023))
2379                 flow_off = 1016;
2380
2381         if ((flow_on < 1) || (flow_on > 1023))
2382                 flow_on = 944;
2383
2384         if ((rx_timeout < 0) || (rx_timeout > 255))
2385                 rx_timeout = 128;
2386
2387         if (flow_on >= flow_off)
2388                 flow_on = flow_off - 1;
2389
2390         show_serial_version();
2391
2392         /* Initialize the tty_driver structure */
2393
2394         esp_driver->owner = THIS_MODULE;
2395         esp_driver->name = "ttyP";
2396         esp_driver->major = ESP_IN_MAJOR;
2397         esp_driver->minor_start = 0;
2398         esp_driver->type = TTY_DRIVER_TYPE_SERIAL;
2399         esp_driver->subtype = SERIAL_TYPE_NORMAL;
2400         esp_driver->init_termios = tty_std_termios;
2401         esp_driver->init_termios.c_cflag =
2402                 B9600 | CS8 | CREAD | HUPCL | CLOCAL;
2403         esp_driver->init_termios.c_ispeed = 9600;
2404         esp_driver->init_termios.c_ospeed = 9600;
2405         esp_driver->flags = TTY_DRIVER_REAL_RAW;
2406         tty_set_operations(esp_driver, &esp_ops);
2407         if (tty_register_driver(esp_driver)) {
2408                 printk(KERN_ERR "Couldn't register esp serial driver");
2409                 put_tty_driver(esp_driver);
2410                 return 1;
2411         }
2412
2413         info = kzalloc(sizeof(struct esp_struct), GFP_KERNEL);
2414
2415         if (!info) {
2416                 printk(KERN_ERR "Couldn't allocate memory for esp serial device information\n");
2417                 tty_unregister_driver(esp_driver);
2418                 put_tty_driver(esp_driver);
2419                 return 1;
2420         }
2421
2422         spin_lock_init(&info->lock);
2423         /* rx_trigger, tx_trigger are needed by autoconfig */
2424         info->config.rx_trigger = rx_trigger;
2425         info->config.tx_trigger = tx_trigger;
2426
2427         i = 0;
2428         offset = 0;
2429
2430         do {
2431                 tty_port_init(&info->port);
2432                 info->port.ops = &esp_port_ops;
2433                 info->io_port = esp[i] + offset;
2434                 info->irq = irq[i];
2435                 info->line = (i * 8) + (offset / 8);
2436
2437                 if (!autoconfig(info)) {
2438                         i++;
2439                         offset = 0;
2440                         continue;
2441                 }
2442
2443                 info->custom_divisor = (divisor[i] >> (offset / 2)) & 0xf;
2444                 info->port.flags = STD_COM_FLAGS;
2445                 if (info->custom_divisor)
2446                         info->port.flags |= ASYNC_SPD_CUST;
2447                 info->magic = ESP_MAGIC;
2448                 info->close_delay = 5*HZ/10;
2449                 info->closing_wait = 30*HZ;
2450                 info->config.rx_timeout = rx_timeout;
2451                 info->config.flow_on = flow_on;
2452                 info->config.flow_off = flow_off;
2453                 info->config.pio_threshold = pio_threshold;
2454                 info->next_port = ports;
2455                 init_waitqueue_head(&info->delta_msr_wait);
2456                 init_waitqueue_head(&info->break_wait);
2457                 ports = info;
2458                 printk(KERN_INFO "ttyP%d at 0x%04x (irq = %d) is an ESP ",
2459                         info->line, info->io_port, info->irq);
2460
2461                 if (info->line % 8) {
2462                         printk("secondary port\n");
2463                         /* 8 port cards can't do DMA */
2464                         info->stat_flags |= ESP_STAT_NEVER_DMA;
2465
2466                         if (last_primary)
2467                                 last_primary->stat_flags |= ESP_STAT_NEVER_DMA;
2468                 } else {
2469                         printk("primary port\n");
2470                         last_primary = info;
2471                         irq[i] = info->irq;
2472                 }
2473
2474                 if (!dma)
2475                         info->stat_flags |= ESP_STAT_NEVER_DMA;
2476
2477                 info = kzalloc(sizeof(struct esp_struct), GFP_KERNEL);
2478                 if (!info) {
2479                         printk(KERN_ERR "Couldn't allocate memory for esp serial device information\n");
2480                         /* allow use of the already detected ports */
2481                         return 0;
2482                 }
2483
2484                 spin_lock_init(&info->lock);
2485                 /* rx_trigger, tx_trigger are needed by autoconfig */
2486                 info->config.rx_trigger = rx_trigger;
2487                 info->config.tx_trigger = tx_trigger;
2488
2489                 if (offset == 56) {
2490                         i++;
2491                         offset = 0;
2492                 } else {
2493                         offset += 8;
2494                 }
2495         } while (i < NR_PRIMARY);
2496
2497         /* free the last port memory allocation */
2498         kfree(info);
2499
2500         return 0;
2501 }
2502
2503 static void __exit espserial_exit(void)
2504 {
2505         int e1;
2506         struct esp_struct *temp_async;
2507         struct esp_pio_buffer *pio_buf;
2508
2509         e1 = tty_unregister_driver(esp_driver);
2510         if (e1)
2511                 printk(KERN_ERR "esp: failed to unregister driver (%d)\n", e1);
2512         put_tty_driver(esp_driver);
2513
2514         while (ports) {
2515                 if (ports->io_port)
2516                         release_region(ports->io_port, REGION_SIZE);
2517                 temp_async = ports->next_port;
2518                 kfree(ports);
2519                 ports = temp_async;
2520         }
2521
2522         if (dma_buffer)
2523                 free_pages((unsigned long)dma_buffer,
2524                         get_order(DMA_BUFFER_SZ));
2525
2526         while (free_pio_buf) {
2527                 pio_buf = free_pio_buf->next;
2528                 kfree(free_pio_buf);
2529                 free_pio_buf = pio_buf;
2530         }
2531 }
2532
2533 module_init(espserial_init);
2534 module_exit(espserial_exit);