git.oblomov.eu Git - linux-2.6/blob - drivers/scsi/aic7xxx/aic7xxx_pci.c

   1 /*
   2  * Product specific probe and attach routines for:
   3  *      3940, 2940, aic7895, aic7890, aic7880,
   4  *      aic7870, aic7860 and aic7850 SCSI controllers
   5  *
   6  * Copyright (c) 1994-2001 Justin T. Gibbs.
   7  * Copyright (c) 2000-2001 Adaptec Inc.
   8  * All rights reserved.
   9  *
  10  * Redistribution and use in source and binary forms, with or without
  11  * modification, are permitted provided that the following conditions
  12  * are met:
  13  * 1. Redistributions of source code must retain the above copyright
  14  *    notice, this list of conditions, and the following disclaimer,
  15  *    without modification.
  16  * 2. Redistributions in binary form must reproduce at minimum a disclaimer
  17  *    substantially similar to the "NO WARRANTY" disclaimer below
  18  *    ("Disclaimer") and any redistribution must be conditioned upon
  19  *    including a substantially similar Disclaimer requirement for further
  20  *    binary redistribution.
  21  * 3. Neither the names of the above-listed copyright holders nor the names
  22  *    of any contributors may be used to endorse or promote products derived
  23  *    from this software without specific prior written permission.
  24  *
  25  * Alternatively, this software may be distributed under the terms of the
  26  * GNU General Public License ("GPL") version 2 as published by the Free
  27  * Software Foundation.
  28  *
  29  * NO WARRANTY
  30  * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
  31  * "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
  32  * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTIBILITY AND FITNESS FOR
  33  * A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT
  34  * HOLDERS OR CONTRIBUTORS BE LIABLE FOR SPECIAL, EXEMPLARY, OR CONSEQUENTIAL
  35  * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS
  36  * OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION)
  37  * HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT,
  38  * STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING
  39  * IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
  40  * POSSIBILITY OF SUCH DAMAGES.
  41  *
  42  * $Id: //depot/aic7xxx/aic7xxx/aic7xxx_pci.c#69 $
  43  *
  44  * $FreeBSD$
  45  */
  46
  47 #ifdef __linux__
  48 #include "aic7xxx_osm.h"
  49 #include "aic7xxx_inline.h"
  50 #include "aic7xxx_93cx6.h"
  51 #else
  52 #include <dev/aic7xxx/aic7xxx_osm.h>
  53 #include <dev/aic7xxx/aic7xxx_inline.h>
  54 #include <dev/aic7xxx/aic7xxx_93cx6.h>
  55 #endif
  56
  57 #include "aic7xxx_pci.h"
  58
  59 static __inline uint64_t
  60 ahc_compose_id(u_int device, u_int vendor, u_int subdevice, u_int subvendor)
  61 {
  62         uint64_t id;
  63
  64         id = subvendor
  65            | (subdevice << 16)
  66            | ((uint64_t)vendor << 32)
  67            | ((uint64_t)device << 48);
  68
  69         return (id);
  70 }
  71
  72 #define AHC_PCI_IOADDR  PCIR_MAPS       /* I/O Address */
  73 #define AHC_PCI_MEMADDR (PCIR_MAPS + 4) /* Mem I/O Address */
  74
  75 #define DEVID_9005_TYPE(id) ((id) & 0xF)
  76 #define         DEVID_9005_TYPE_HBA             0x0     /* Standard Card */
  77 #define         DEVID_9005_TYPE_AAA             0x3     /* RAID Card */
  78 #define         DEVID_9005_TYPE_SISL            0x5     /* Container ROMB */
  79 #define         DEVID_9005_TYPE_MB              0xF     /* On Motherboard */
  80
  81 #define DEVID_9005_MAXRATE(id) (((id) & 0x30) >> 4)
  82 #define         DEVID_9005_MAXRATE_U160         0x0
  83 #define         DEVID_9005_MAXRATE_ULTRA2       0x1
  84 #define         DEVID_9005_MAXRATE_ULTRA        0x2
  85 #define         DEVID_9005_MAXRATE_FAST         0x3
  86
  87 #define DEVID_9005_MFUNC(id) (((id) & 0x40) >> 6)
  88
  89 #define DEVID_9005_CLASS(id) (((id) & 0xFF00) >> 8)
  90 #define         DEVID_9005_CLASS_SPI            0x0     /* Parallel SCSI */
  91
  92 #define SUBID_9005_TYPE(id) ((id) & 0xF)
  93 #define         SUBID_9005_TYPE_MB              0xF     /* On Motherboard */
  94 #define         SUBID_9005_TYPE_CARD            0x0     /* Standard Card */
  95 #define         SUBID_9005_TYPE_LCCARD          0x1     /* Low Cost Card */
  96 #define         SUBID_9005_TYPE_RAID            0x3     /* Combined with Raid */
  97
  98 #define SUBID_9005_TYPE_KNOWN(id)                       \
  99           ((((id) & 0xF) == SUBID_9005_TYPE_MB)         \
 100         || (((id) & 0xF) == SUBID_9005_TYPE_CARD)       \
 101         || (((id) & 0xF) == SUBID_9005_TYPE_LCCARD)     \
 102         || (((id) & 0xF) == SUBID_9005_TYPE_RAID))
 103
 104 #define SUBID_9005_MAXRATE(id) (((id) & 0x30) >> 4)
 105 #define         SUBID_9005_MAXRATE_ULTRA2       0x0
 106 #define         SUBID_9005_MAXRATE_ULTRA        0x1
 107 #define         SUBID_9005_MAXRATE_U160         0x2
 108 #define         SUBID_9005_MAXRATE_RESERVED     0x3
 109
 110 #define SUBID_9005_SEEPTYPE(id)                                         \
 111         ((SUBID_9005_TYPE(id) == SUBID_9005_TYPE_MB)                    \
 112          ? ((id) & 0xC0) >> 6                                           \
 113          : ((id) & 0x300) >> 8)
 114 #define         SUBID_9005_SEEPTYPE_NONE        0x0
 115 #define         SUBID_9005_SEEPTYPE_1K          0x1
 116 #define         SUBID_9005_SEEPTYPE_2K_4K       0x2
 117 #define         SUBID_9005_SEEPTYPE_RESERVED    0x3
 118 #define SUBID_9005_AUTOTERM(id)                                         \
 119         ((SUBID_9005_TYPE(id) == SUBID_9005_TYPE_MB)                    \
 120          ? (((id) & 0x400) >> 10) == 0                                  \
 121          : (((id) & 0x40) >> 6) == 0)
 122
 123 #define SUBID_9005_NUMCHAN(id)                                          \
 124         ((SUBID_9005_TYPE(id) == SUBID_9005_TYPE_MB)                    \
 125          ? ((id) & 0x300) >> 8                                          \
 126          : ((id) & 0xC00) >> 10)
 127
 128 #define SUBID_9005_LEGACYCONN(id)                                       \
 129         ((SUBID_9005_TYPE(id) == SUBID_9005_TYPE_MB)                    \
 130          ? 0                                                            \
 131          : ((id) & 0x80) >> 7)
 132
 133 #define SUBID_9005_MFUNCENB(id)                                         \
 134         ((SUBID_9005_TYPE(id) == SUBID_9005_TYPE_MB)                    \
 135          ? ((id) & 0x800) >> 11                                         \
 136          : ((id) & 0x1000) >> 12)
 137 /*
 138  * Informational only. Should use chip register to be
 139  * certain, but may be use in identification strings.
 140  */
 141 #define SUBID_9005_CARD_SCSIWIDTH_MASK  0x2000
 142 #define SUBID_9005_CARD_PCIWIDTH_MASK   0x4000
 143 #define SUBID_9005_CARD_SEDIFF_MASK     0x8000
 144
 145 static ahc_device_setup_t ahc_aic785X_setup;
 146 static ahc_device_setup_t ahc_aic7860_setup;
 147 static ahc_device_setup_t ahc_apa1480_setup;
 148 static ahc_device_setup_t ahc_aic7870_setup;
 149 static ahc_device_setup_t ahc_aha394X_setup;
 150 static ahc_device_setup_t ahc_aha494X_setup;
 151 static ahc_device_setup_t ahc_aha398X_setup;
 152 static ahc_device_setup_t ahc_aic7880_setup;
 153 static ahc_device_setup_t ahc_aha2940Pro_setup;
 154 static ahc_device_setup_t ahc_aha394XU_setup;
 155 static ahc_device_setup_t ahc_aha398XU_setup;
 156 static ahc_device_setup_t ahc_aic7890_setup;
 157 static ahc_device_setup_t ahc_aic7892_setup;
 158 static ahc_device_setup_t ahc_aic7895_setup;
 159 static ahc_device_setup_t ahc_aic7896_setup;
 160 static ahc_device_setup_t ahc_aic7899_setup;
 161 static ahc_device_setup_t ahc_aha29160C_setup;
 162 static ahc_device_setup_t ahc_raid_setup;
 163 static ahc_device_setup_t ahc_aha394XX_setup;
 164 static ahc_device_setup_t ahc_aha494XX_setup;
 165 static ahc_device_setup_t ahc_aha398XX_setup;
 166
 167 struct ahc_pci_identity ahc_pci_ident_table [] =
 168 {
 169         /* aic7850 based controllers */
 170         {
 171                 ID_AHA_2902_04_10_15_20C_30C,
 172                 ID_ALL_MASK,
 173                 "Adaptec 2902/04/10/15/20C/30C SCSI adapter",
 174                 ahc_aic785X_setup
 175         },
 176         /* aic7860 based controllers */
 177         {
 178                 ID_AHA_2930CU,
 179                 ID_ALL_MASK,
 180                 "Adaptec 2930CU SCSI adapter",
 181                 ahc_aic7860_setup
 182         },
 183         {
 184                 ID_AHA_1480A & ID_DEV_VENDOR_MASK,
 185                 ID_DEV_VENDOR_MASK,
 186                 "Adaptec 1480A Ultra SCSI adapter",
 187                 ahc_apa1480_setup
 188         },
 189         {
 190                 ID_AHA_2940AU_0 & ID_DEV_VENDOR_MASK,
 191                 ID_DEV_VENDOR_MASK,
 192                 "Adaptec 2940A Ultra SCSI adapter",
 193                 ahc_aic7860_setup
 194         },
 195         {
 196                 ID_AHA_2940AU_CN & ID_DEV_VENDOR_MASK,
 197                 ID_DEV_VENDOR_MASK,
 198                 "Adaptec 2940A/CN Ultra SCSI adapter",
 199                 ahc_aic7860_setup
 200         },
 201         {
 202                 ID_AHA_2930C_VAR & ID_DEV_VENDOR_MASK,
 203                 ID_DEV_VENDOR_MASK,
 204                 "Adaptec 2930C Ultra SCSI adapter (VAR)",
 205                 ahc_aic7860_setup
 206         },
 207         /* aic7870 based controllers */
 208         {
 209                 ID_AHA_2940,
 210                 ID_ALL_MASK,
 211                 "Adaptec 2940 SCSI adapter",
 212                 ahc_aic7870_setup
 213         },
 214         {
 215                 ID_AHA_3940,
 216                 ID_ALL_MASK,
 217                 "Adaptec 3940 SCSI adapter",
 218                 ahc_aha394X_setup
 219         },
 220         {
 221                 ID_AHA_398X,
 222                 ID_ALL_MASK,
 223                 "Adaptec 398X SCSI RAID adapter",
 224                 ahc_aha398X_setup
 225         },
 226         {
 227                 ID_AHA_2944,
 228                 ID_ALL_MASK,
 229                 "Adaptec 2944 SCSI adapter",
 230                 ahc_aic7870_setup
 231         },
 232         {
 233                 ID_AHA_3944,
 234                 ID_ALL_MASK,
 235                 "Adaptec 3944 SCSI adapter",
 236                 ahc_aha394X_setup
 237         },
 238         {
 239                 ID_AHA_4944,
 240                 ID_ALL_MASK,
 241                 "Adaptec 4944 SCSI adapter",
 242                 ahc_aha494X_setup
 243         },
 244         /* aic7880 based controllers */
 245         {
 246                 ID_AHA_2940U & ID_DEV_VENDOR_MASK,
 247                 ID_DEV_VENDOR_MASK,
 248                 "Adaptec 2940 Ultra SCSI adapter",
 249                 ahc_aic7880_setup
 250         },
 251         {
 252                 ID_AHA_3940U & ID_DEV_VENDOR_MASK,
 253                 ID_DEV_VENDOR_MASK,
 254                 "Adaptec 3940 Ultra SCSI adapter",
 255                 ahc_aha394XU_setup
 256         },
 257         {
 258                 ID_AHA_2944U & ID_DEV_VENDOR_MASK,
 259                 ID_DEV_VENDOR_MASK,
 260                 "Adaptec 2944 Ultra SCSI adapter",
 261                 ahc_aic7880_setup
 262         },
 263         {
 264                 ID_AHA_3944U & ID_DEV_VENDOR_MASK,
 265                 ID_DEV_VENDOR_MASK,
 266                 "Adaptec 3944 Ultra SCSI adapter",
 267                 ahc_aha394XU_setup
 268         },
 269         {
 270                 ID_AHA_398XU & ID_DEV_VENDOR_MASK,
 271                 ID_DEV_VENDOR_MASK,
 272                 "Adaptec 398X Ultra SCSI RAID adapter",
 273                 ahc_aha398XU_setup
 274         },
 275         {
 276                 /*
 277                  * XXX Don't know the slot numbers
 278                  * so we can't identify channels
 279                  */
 280                 ID_AHA_4944U & ID_DEV_VENDOR_MASK,
 281                 ID_DEV_VENDOR_MASK,
 282                 "Adaptec 4944 Ultra SCSI adapter",
 283                 ahc_aic7880_setup
 284         },
 285         {
 286                 ID_AHA_2930U & ID_DEV_VENDOR_MASK,
 287                 ID_DEV_VENDOR_MASK,
 288                 "Adaptec 2930 Ultra SCSI adapter",
 289                 ahc_aic7880_setup
 290         },
 291         {
 292                 ID_AHA_2940U_PRO & ID_DEV_VENDOR_MASK,
 293                 ID_DEV_VENDOR_MASK,
 294                 "Adaptec 2940 Pro Ultra SCSI adapter",
 295                 ahc_aha2940Pro_setup
 296         },
 297         {
 298                 ID_AHA_2940U_CN & ID_DEV_VENDOR_MASK,
 299                 ID_DEV_VENDOR_MASK,
 300                 "Adaptec 2940/CN Ultra SCSI adapter",
 301                 ahc_aic7880_setup
 302         },
 303         /* Ignore all SISL (AAC on MB) based controllers. */
 304         {
 305                 ID_9005_SISL_ID,
 306                 ID_9005_SISL_MASK,
 307                 NULL,
 308                 NULL
 309         },
 310         /* aic7890 based controllers */
 311         {
 312                 ID_AHA_2930U2,
 313                 ID_ALL_MASK,
 314                 "Adaptec 2930 Ultra2 SCSI adapter",
 315                 ahc_aic7890_setup
 316         },
 317         {
 318                 ID_AHA_2940U2B,
 319                 ID_ALL_MASK,
 320                 "Adaptec 2940B Ultra2 SCSI adapter",
 321                 ahc_aic7890_setup
 322         },
 323         {
 324                 ID_AHA_2940U2_OEM,
 325                 ID_ALL_MASK,
 326                 "Adaptec 2940 Ultra2 SCSI adapter (OEM)",
 327                 ahc_aic7890_setup
 328         },
 329         {
 330                 ID_AHA_2940U2,
 331                 ID_ALL_MASK,
 332                 "Adaptec 2940 Ultra2 SCSI adapter",
 333                 ahc_aic7890_setup
 334         },
 335         {
 336                 ID_AHA_2950U2B,
 337                 ID_ALL_MASK,
 338                 "Adaptec 2950 Ultra2 SCSI adapter",
 339                 ahc_aic7890_setup
 340         },
 341         {
 342                 ID_AIC7890_ARO,
 343                 ID_ALL_MASK,
 344                 "Adaptec aic7890/91 Ultra2 SCSI adapter (ARO)",
 345                 ahc_aic7890_setup
 346         },
 347         {
 348                 ID_AAA_131U2,
 349                 ID_ALL_MASK,
 350                 "Adaptec AAA-131 Ultra2 RAID adapter",
 351                 ahc_aic7890_setup
 352         },
 353         /* aic7892 based controllers */
 354         {
 355                 ID_AHA_29160,
 356                 ID_ALL_MASK,
 357                 "Adaptec 29160 Ultra160 SCSI adapter",
 358                 ahc_aic7892_setup
 359         },
 360         {
 361                 ID_AHA_29160_CPQ,
 362                 ID_ALL_MASK,
 363                 "Adaptec (Compaq OEM) 29160 Ultra160 SCSI adapter",
 364                 ahc_aic7892_setup
 365         },
 366         {
 367                 ID_AHA_29160N,
 368                 ID_ALL_MASK,
 369                 "Adaptec 29160N Ultra160 SCSI adapter",
 370                 ahc_aic7892_setup
 371         },
 372         {
 373                 ID_AHA_29160C,
 374                 ID_ALL_MASK,
 375                 "Adaptec 29160C Ultra160 SCSI adapter",
 376                 ahc_aha29160C_setup
 377         },
 378         {
 379                 ID_AHA_29160B,
 380                 ID_ALL_MASK,
 381                 "Adaptec 29160B Ultra160 SCSI adapter",
 382                 ahc_aic7892_setup
 383         },
 384         {
 385                 ID_AHA_19160B,
 386                 ID_ALL_MASK,
 387                 "Adaptec 19160B Ultra160 SCSI adapter",
 388                 ahc_aic7892_setup
 389         },
 390         {
 391                 ID_AIC7892_ARO,
 392                 ID_ALL_MASK,
 393                 "Adaptec aic7892 Ultra160 SCSI adapter (ARO)",
 394                 ahc_aic7892_setup
 395         },
 396         /* aic7895 based controllers */
 397         {
 398                 ID_AHA_2940U_DUAL,
 399                 ID_ALL_MASK,
 400                 "Adaptec 2940/DUAL Ultra SCSI adapter",
 401                 ahc_aic7895_setup
 402         },
 403         {
 404                 ID_AHA_3940AU,
 405                 ID_ALL_MASK,
 406                 "Adaptec 3940A Ultra SCSI adapter",
 407                 ahc_aic7895_setup
 408         },
 409         {
 410                 ID_AHA_3944AU,
 411                 ID_ALL_MASK,
 412                 "Adaptec 3944A Ultra SCSI adapter",
 413                 ahc_aic7895_setup
 414         },
 415         {
 416                 ID_AIC7895_ARO,
 417                 ID_AIC7895_ARO_MASK,
 418                 "Adaptec aic7895 Ultra SCSI adapter (ARO)",
 419                 ahc_aic7895_setup
 420         },
 421         /* aic7896/97 based controllers */
 422         {
 423                 ID_AHA_3950U2B_0,
 424                 ID_ALL_MASK,
 425                 "Adaptec 3950B Ultra2 SCSI adapter",
 426                 ahc_aic7896_setup
 427         },
 428         {
 429                 ID_AHA_3950U2B_1,
 430                 ID_ALL_MASK,
 431                 "Adaptec 3950B Ultra2 SCSI adapter",
 432                 ahc_aic7896_setup
 433         },
 434         {
 435                 ID_AHA_3950U2D_0,
 436                 ID_ALL_MASK,
 437                 "Adaptec 3950D Ultra2 SCSI adapter",
 438                 ahc_aic7896_setup
 439         },
 440         {
 441                 ID_AHA_3950U2D_1,
 442                 ID_ALL_MASK,
 443                 "Adaptec 3950D Ultra2 SCSI adapter",
 444                 ahc_aic7896_setup
 445         },
 446         {
 447                 ID_AIC7896_ARO,
 448                 ID_ALL_MASK,
 449                 "Adaptec aic7896/97 Ultra2 SCSI adapter (ARO)",
 450                 ahc_aic7896_setup
 451         },
 452         /* aic7899 based controllers */
 453         {
 454                 ID_AHA_3960D,
 455                 ID_ALL_MASK,
 456                 "Adaptec 3960D Ultra160 SCSI adapter",
 457                 ahc_aic7899_setup
 458         },
 459         {
 460                 ID_AHA_3960D_CPQ,
 461                 ID_ALL_MASK,
 462                 "Adaptec (Compaq OEM) 3960D Ultra160 SCSI adapter",
 463                 ahc_aic7899_setup
 464         },
 465         {
 466                 ID_AIC7899_ARO,
 467                 ID_ALL_MASK,
 468                 "Adaptec aic7899 Ultra160 SCSI adapter (ARO)",
 469                 ahc_aic7899_setup
 470         },
 471         /* Generic chip probes for devices we don't know 'exactly' */
 472         {
 473                 ID_AIC7850 & ID_DEV_VENDOR_MASK,
 474                 ID_DEV_VENDOR_MASK,
 475                 "Adaptec aic7850 SCSI adapter",
 476                 ahc_aic785X_setup
 477         },
 478         {
 479                 ID_AIC7855 & ID_DEV_VENDOR_MASK,
 480                 ID_DEV_VENDOR_MASK,
 481                 "Adaptec aic7855 SCSI adapter",
 482                 ahc_aic785X_setup
 483         },
 484         {
 485                 ID_AIC7859 & ID_DEV_VENDOR_MASK,
 486                 ID_DEV_VENDOR_MASK,
 487                 "Adaptec aic7859 SCSI adapter",
 488                 ahc_aic7860_setup
 489         },
 490         {
 491                 ID_AIC7860 & ID_DEV_VENDOR_MASK,
 492                 ID_DEV_VENDOR_MASK,
 493                 "Adaptec aic7860 Ultra SCSI adapter",
 494                 ahc_aic7860_setup
 495         },
 496         {
 497                 ID_AIC7870 & ID_DEV_VENDOR_MASK,
 498                 ID_DEV_VENDOR_MASK,
 499                 "Adaptec aic7870 SCSI adapter",
 500                 ahc_aic7870_setup
 501         },
 502         {
 503                 ID_AIC7880 & ID_DEV_VENDOR_MASK,
 504                 ID_DEV_VENDOR_MASK,
 505                 "Adaptec aic7880 Ultra SCSI adapter",
 506                 ahc_aic7880_setup
 507         },
 508         {
 509                 ID_AIC7890 & ID_9005_GENERIC_MASK,
 510                 ID_9005_GENERIC_MASK,
 511                 "Adaptec aic7890/91 Ultra2 SCSI adapter",
 512                 ahc_aic7890_setup
 513         },
 514         {
 515                 ID_AIC7892 & ID_9005_GENERIC_MASK,
 516                 ID_9005_GENERIC_MASK,
 517                 "Adaptec aic7892 Ultra160 SCSI adapter",
 518                 ahc_aic7892_setup
 519         },
 520         {
 521                 ID_AIC7895 & ID_DEV_VENDOR_MASK,
 522                 ID_DEV_VENDOR_MASK,
 523                 "Adaptec aic7895 Ultra SCSI adapter",
 524                 ahc_aic7895_setup
 525         },
 526         {
 527                 ID_AIC7896 & ID_9005_GENERIC_MASK,
 528                 ID_9005_GENERIC_MASK,
 529                 "Adaptec aic7896/97 Ultra2 SCSI adapter",
 530                 ahc_aic7896_setup
 531         },
 532         {
 533                 ID_AIC7899 & ID_9005_GENERIC_MASK,
 534                 ID_9005_GENERIC_MASK,
 535                 "Adaptec aic7899 Ultra160 SCSI adapter",
 536                 ahc_aic7899_setup
 537         },
 538         {
 539                 ID_AIC7810 & ID_DEV_VENDOR_MASK,
 540                 ID_DEV_VENDOR_MASK,
 541                 "Adaptec aic7810 RAID memory controller",
 542                 ahc_raid_setup
 543         },
 544         {
 545                 ID_AIC7815 & ID_DEV_VENDOR_MASK,
 546                 ID_DEV_VENDOR_MASK,
 547                 "Adaptec aic7815 RAID memory controller",
 548                 ahc_raid_setup
 549         }
 550 };
 551
 552 const u_int ahc_num_pci_devs = NUM_ELEMENTS(ahc_pci_ident_table);
 553
 554 #define AHC_394X_SLOT_CHANNEL_A 4
 555 #define AHC_394X_SLOT_CHANNEL_B 5
 556
 557 #define AHC_398X_SLOT_CHANNEL_A 4
 558 #define AHC_398X_SLOT_CHANNEL_B 8
 559 #define AHC_398X_SLOT_CHANNEL_C 12
 560
 561 #define AHC_494X_SLOT_CHANNEL_A 4
 562 #define AHC_494X_SLOT_CHANNEL_B 5
 563 #define AHC_494X_SLOT_CHANNEL_C 6
 564 #define AHC_494X_SLOT_CHANNEL_D 7
 565
 566 #define DEVCONFIG               0x40
 567 #define         PCIERRGENDIS    0x80000000ul
 568 #define         SCBSIZE32       0x00010000ul    /* aic789X only */
 569 #define         REXTVALID       0x00001000ul    /* ultra cards only */
 570 #define         MPORTMODE       0x00000400ul    /* aic7870+ only */
 571 #define         RAMPSM          0x00000200ul    /* aic7870+ only */
 572 #define         VOLSENSE        0x00000100ul
 573 #define         PCI64BIT        0x00000080ul    /* 64Bit PCI bus (Ultra2 Only)*/
 574 #define         SCBRAMSEL       0x00000080ul
 575 #define         MRDCEN          0x00000040ul
 576 #define         EXTSCBTIME      0x00000020ul    /* aic7870 only */
 577 #define         EXTSCBPEN       0x00000010ul    /* aic7870 only */
 578 #define         BERREN          0x00000008ul
 579 #define         DACEN           0x00000004ul
 580 #define         STPWLEVEL       0x00000002ul
 581 #define         DIFACTNEGEN     0x00000001ul    /* aic7870 only */
 582
 583 #define CSIZE_LATTIME           0x0c
 584 #define         CACHESIZE       0x0000003ful    /* only 5 bits */
 585 #define         LATTIME         0x0000ff00ul
 586
 587 /* PCI STATUS definitions */
 588 #define DPE     0x80
 589 #define SSE     0x40
 590 #define RMA     0x20
 591 #define RTA     0x10
 592 #define STA     0x08
 593 #define DPR     0x01
 594
 595 static int ahc_9005_subdevinfo_valid(uint16_t vendor, uint16_t device,
 596                                      uint16_t subvendor, uint16_t subdevice);
 597 static int ahc_ext_scbram_present(struct ahc_softc *ahc);
 598 static void ahc_scbram_config(struct ahc_softc *ahc, int enable,
 599                                   int pcheck, int fast, int large);
 600 static void ahc_probe_ext_scbram(struct ahc_softc *ahc);
 601 static void check_extport(struct ahc_softc *ahc, u_int *sxfrctl1);
 602 static void ahc_parse_pci_eeprom(struct ahc_softc *ahc,
 603                                  struct seeprom_config *sc);
 604 static void configure_termination(struct ahc_softc *ahc,
 605                                   struct seeprom_descriptor *sd,
 606                                   u_int adapter_control,
 607                                   u_int *sxfrctl1);
 608
 609 static void ahc_new_term_detect(struct ahc_softc *ahc,
 610                                 int *enableSEC_low,
 611                                 int *enableSEC_high,
 612                                 int *enablePRI_low,
 613                                 int *enablePRI_high,
 614                                 int *eeprom_present);
 615 static void aic787X_cable_detect(struct ahc_softc *ahc, int *internal50_present,
 616                                  int *internal68_present,
 617                                  int *externalcable_present,
 618                                  int *eeprom_present);
 619 static void aic785X_cable_detect(struct ahc_softc *ahc, int *internal50_present,
 620                                  int *externalcable_present,
 621                                  int *eeprom_present);
 622 static void    write_brdctl(struct ahc_softc *ahc, uint8_t value);
 623 static uint8_t read_brdctl(struct ahc_softc *ahc);
 624 static void ahc_pci_intr(struct ahc_softc *ahc);
 625 static int  ahc_pci_chip_init(struct ahc_softc *ahc);
 626 static int  ahc_pci_suspend(struct ahc_softc *ahc);
 627 static int  ahc_pci_resume(struct ahc_softc *ahc);
 628
 629 static int
 630 ahc_9005_subdevinfo_valid(uint16_t device, uint16_t vendor,
 631                           uint16_t subdevice, uint16_t subvendor)
 632 {
 633         int result;
 634
 635         /* Default to invalid. */
 636         result = 0;
 637         if (vendor == 0x9005
 638          && subvendor == 0x9005
 639          && subdevice != device
 640          && SUBID_9005_TYPE_KNOWN(subdevice) != 0) {
 641
 642                 switch (SUBID_9005_TYPE(subdevice)) {
 643                 case SUBID_9005_TYPE_MB:
 644                         break;
 645                 case SUBID_9005_TYPE_CARD:
 646                 case SUBID_9005_TYPE_LCCARD:
 647                         /*
 648                          * Currently only trust Adaptec cards to
 649                          * get the sub device info correct.
 650                          */
 651                         if (DEVID_9005_TYPE(device) == DEVID_9005_TYPE_HBA)
 652                                 result = 1;
 653                         break;
 654                 case SUBID_9005_TYPE_RAID:
 655                         break;
 656                 default:
 657                         break;
 658                 }
 659         }
 660         return (result);
 661 }
 662
 663 struct ahc_pci_identity *
 664 ahc_find_pci_device(ahc_dev_softc_t pci)
 665 {
 666         uint64_t  full_id;
 667         uint16_t  device;
 668         uint16_t  vendor;
 669         uint16_t  subdevice;
 670         uint16_t  subvendor;
 671         struct    ahc_pci_identity *entry;
 672         u_int     i;
 673
 674         vendor = ahc_pci_read_config(pci, PCIR_DEVVENDOR, /*bytes*/2);
 675         device = ahc_pci_read_config(pci, PCIR_DEVICE, /*bytes*/2);
 676         subvendor = ahc_pci_read_config(pci, PCIR_SUBVEND_0, /*bytes*/2);
 677         subdevice = ahc_pci_read_config(pci, PCIR_SUBDEV_0, /*bytes*/2);
 678         full_id = ahc_compose_id(device, vendor, subdevice, subvendor);
 679
 680         /*
 681          * If the second function is not hooked up, ignore it.
 682          * Unfortunately, not all MB vendors implement the
 683          * subdevice ID as per the Adaptec spec, so do our best
 684          * to sanity check it prior to accepting the subdevice
 685          * ID as valid.
 686          */
 687         if (ahc_get_pci_function(pci) > 0
 688          && ahc_9005_subdevinfo_valid(vendor, device, subvendor, subdevice)
 689          && SUBID_9005_MFUNCENB(subdevice) == 0)
 690                 return (NULL);
 691
 692         for (i = 0; i < ahc_num_pci_devs; i++) {
 693                 entry = &ahc_pci_ident_table[i];
 694                 if (entry->full_id == (full_id & entry->id_mask)) {
 695                         /* Honor exclusion entries. */
 696                         if (entry->name == NULL)
 697                                 return (NULL);
 698                         return (entry);
 699                 }
 700         }
 701         return (NULL);
 702 }
 703
 704 int
 705 ahc_pci_config(struct ahc_softc *ahc, struct ahc_pci_identity *entry)
 706 {
 707         u_int    command;
 708         u_int    our_id;
 709         u_int    sxfrctl1;
 710         u_int    scsiseq;
 711         u_int    dscommand0;
 712         uint32_t devconfig;
 713         int      error;
 714         uint8_t  sblkctl;
 715
 716         our_id = 0;
 717         error = entry->setup(ahc);
 718         if (error != 0)
 719                 return (error);
 720         ahc->chip |= AHC_PCI;
 721         ahc->description = entry->name;
 722
 723         pci_set_power_state(ahc->dev_softc, AHC_POWER_STATE_D0);
 724
 725         error = ahc_pci_map_registers(ahc);
 726         if (error != 0)
 727                 return (error);
 728
 729         /*
 730          * Before we continue probing the card, ensure that
 731          * its interrupts are *disabled*.  We don't want
 732          * a misstep to hang the machine in an interrupt
 733          * storm.
 734          */
 735         ahc_intr_enable(ahc, FALSE);
 736
 737         devconfig = ahc_pci_read_config(ahc->dev_softc, DEVCONFIG, /*bytes*/4);
 738
 739         /*
 740          * If we need to support high memory, enable dual
 741          * address cycles.  This bit must be set to enable
 742          * high address bit generation even if we are on a
 743          * 64bit bus (PCI64BIT set in devconfig).
 744          */
 745         if ((ahc->flags & AHC_39BIT_ADDRESSING) != 0) {
 746
 747                 if (bootverbose)
 748                         printf("%s: Enabling 39Bit Addressing\n",
 749                                ahc_name(ahc));
 750                 devconfig |= DACEN;
 751         }
 752
 753         /* Ensure that pci error generation, a test feature, is disabled. */
 754         devconfig |= PCIERRGENDIS;
 755
 756         ahc_pci_write_config(ahc->dev_softc, DEVCONFIG, devconfig, /*bytes*/4);
 757
 758         /* Ensure busmastering is enabled */
 759         command = ahc_pci_read_config(ahc->dev_softc, PCIR_COMMAND, /*bytes*/2);
 760         command |= PCIM_CMD_BUSMASTEREN;
 761
 762         ahc_pci_write_config(ahc->dev_softc, PCIR_COMMAND, command, /*bytes*/2);
 763
 764         /* On all PCI adapters, we allow SCB paging */
 765         ahc->flags |= AHC_PAGESCBS;
 766
 767         error = ahc_softc_init(ahc);
 768         if (error != 0)
 769                 return (error);
 770
 771         /*
 772          * Disable PCI parity error checking.  Users typically
 773          * do this to work around broken PCI chipsets that get
 774          * the parity timing wrong and thus generate lots of spurious
 775          * errors.  The chip only allows us to disable *all* parity
 776          * error reporting when doing this, so CIO bus, scb ram, and
 777          * scratch ram parity errors will be ignored too.
 778          */
 779         if ((ahc->flags & AHC_DISABLE_PCI_PERR) != 0)
 780                 ahc->seqctl |= FAILDIS;
 781
 782         ahc->bus_intr = ahc_pci_intr;
 783         ahc->bus_chip_init = ahc_pci_chip_init;
 784         ahc->bus_suspend = ahc_pci_suspend;
 785         ahc->bus_resume = ahc_pci_resume;
 786
 787         /* Remeber how the card was setup in case there is no SEEPROM */
 788         if ((ahc_inb(ahc, HCNTRL) & POWRDN) == 0) {
 789                 ahc_pause(ahc);
 790                 if ((ahc->features & AHC_ULTRA2) != 0)
 791                         our_id = ahc_inb(ahc, SCSIID_ULTRA2) & OID;
 792                 else
 793                         our_id = ahc_inb(ahc, SCSIID) & OID;
 794                 sxfrctl1 = ahc_inb(ahc, SXFRCTL1) & STPWEN;
 795                 scsiseq = ahc_inb(ahc, SCSISEQ);
 796         } else {
 797                 sxfrctl1 = STPWEN;
 798                 our_id = 7;
 799                 scsiseq = 0;
 800         }
 801
 802         error = ahc_reset(ahc, /*reinit*/FALSE);
 803         if (error != 0)
 804                 return (ENXIO);
 805
 806         if ((ahc->features & AHC_DT) != 0) {
 807                 u_int sfunct;
 808
 809                 /* Perform ALT-Mode Setup */
 810                 sfunct = ahc_inb(ahc, SFUNCT) & ~ALT_MODE;
 811                 ahc_outb(ahc, SFUNCT, sfunct | ALT_MODE);
 812                 ahc_outb(ahc, OPTIONMODE,
 813                          OPTIONMODE_DEFAULTS|AUTOACKEN|BUSFREEREV|EXPPHASEDIS);
 814                 ahc_outb(ahc, SFUNCT, sfunct);
 815
 816                 /* Normal mode setup */
 817                 ahc_outb(ahc, CRCCONTROL1, CRCVALCHKEN|CRCENDCHKEN|CRCREQCHKEN
 818                                           |TARGCRCENDEN);
 819         }
 820
 821         dscommand0 = ahc_inb(ahc, DSCOMMAND0);
 822         dscommand0 |= MPARCKEN|CACHETHEN;
 823         if ((ahc->features & AHC_ULTRA2) != 0) {
 824
 825                 /*
 826                  * DPARCKEN doesn't work correctly on
 827                  * some MBs so don't use it.
 828                  */
 829                 dscommand0 &= ~DPARCKEN;
 830         }
 831
 832         /*
 833          * Handle chips that must have cache line
 834          * streaming (dis/en)abled.
 835          */
 836         if ((ahc->bugs & AHC_CACHETHEN_DIS_BUG) != 0)
 837                 dscommand0 |= CACHETHEN;
 838
 839         if ((ahc->bugs & AHC_CACHETHEN_BUG) != 0)
 840                 dscommand0 &= ~CACHETHEN;
 841
 842         ahc_outb(ahc, DSCOMMAND0, dscommand0);
 843
 844         ahc->pci_cachesize =
 845             ahc_pci_read_config(ahc->dev_softc, CSIZE_LATTIME,
 846                                 /*bytes*/1) & CACHESIZE;
 847         ahc->pci_cachesize *= 4;
 848
 849         if ((ahc->bugs & AHC_PCI_2_1_RETRY_BUG) != 0
 850          && ahc->pci_cachesize == 4) {
 851
 852                 ahc_pci_write_config(ahc->dev_softc, CSIZE_LATTIME,
 853                                      0, /*bytes*/1);
 854                 ahc->pci_cachesize = 0;
 855         }
 856
 857         /*
 858          * We cannot perform ULTRA speeds without the presense
 859          * of the external precision resistor.
 860          */
 861         if ((ahc->features & AHC_ULTRA) != 0) {
 862                 uint32_t devconfig;
 863
 864                 devconfig = ahc_pci_read_config(ahc->dev_softc,
 865                                                 DEVCONFIG, /*bytes*/4);
 866                 if ((devconfig & REXTVALID) == 0)
 867                         ahc->features &= ~AHC_ULTRA;
 868         }
 869
 870         /* See if we have a SEEPROM and perform auto-term */
 871         check_extport(ahc, &sxfrctl1);
 872
 873         /*
 874          * Take the LED out of diagnostic mode
 875          */
 876         sblkctl = ahc_inb(ahc, SBLKCTL);
 877         ahc_outb(ahc, SBLKCTL, (sblkctl & ~(DIAGLEDEN|DIAGLEDON)));
 878
 879         if ((ahc->features & AHC_ULTRA2) != 0) {
 880                 ahc_outb(ahc, DFF_THRSH, RD_DFTHRSH_MAX|WR_DFTHRSH_MAX);
 881         } else {
 882                 ahc_outb(ahc, DSPCISTATUS, DFTHRSH_100);
 883         }
 884
 885         if (ahc->flags & AHC_USEDEFAULTS) {
 886                 /*
 887                  * PCI Adapter default setup
 888                  * Should only be used if the adapter does not have
 889                  * a SEEPROM.
 890                  */
 891                 /* See if someone else set us up already */
 892                 if ((ahc->flags & AHC_NO_BIOS_INIT) == 0
 893                  && scsiseq != 0) {
 894                         printf("%s: Using left over BIOS settings\n",
 895                                 ahc_name(ahc));
 896                         ahc->flags &= ~AHC_USEDEFAULTS;
 897                         ahc->flags |= AHC_BIOS_ENABLED;
 898                 } else {
 899                         /*
 900                          * Assume only one connector and always turn
 901                          * on termination.
 902                          */
 903                         our_id = 0x07;
 904                         sxfrctl1 = STPWEN;
 905                 }
 906                 ahc_outb(ahc, SCSICONF, our_id|ENSPCHK|RESET_SCSI);
 907
 908                 ahc->our_id = our_id;
 909         }
 910
 911         /*
 912          * Take a look to see if we have external SRAM.
 913          * We currently do not attempt to use SRAM that is
 914          * shared among multiple controllers.
 915          */
 916         ahc_probe_ext_scbram(ahc);
 917
 918         /*
 919          * Record our termination setting for the
 920          * generic initialization routine.
 921          */
 922         if ((sxfrctl1 & STPWEN) != 0)
 923                 ahc->flags |= AHC_TERM_ENB_A;
 924
 925         /*
 926          * Save chip register configuration data for chip resets
 927          * that occur during runtime and resume events.
 928          */
 929         ahc->bus_softc.pci_softc.devconfig =
 930             ahc_pci_read_config(ahc->dev_softc, DEVCONFIG, /*bytes*/4);
 931         ahc->bus_softc.pci_softc.command =
 932             ahc_pci_read_config(ahc->dev_softc, PCIR_COMMAND, /*bytes*/1);
 933         ahc->bus_softc.pci_softc.csize_lattime =
 934             ahc_pci_read_config(ahc->dev_softc, CSIZE_LATTIME, /*bytes*/1);
 935         ahc->bus_softc.pci_softc.dscommand0 = ahc_inb(ahc, DSCOMMAND0);
 936         ahc->bus_softc.pci_softc.dspcistatus = ahc_inb(ahc, DSPCISTATUS);
 937         if ((ahc->features & AHC_DT) != 0) {
 938                 u_int sfunct;
 939
 940                 sfunct = ahc_inb(ahc, SFUNCT) & ~ALT_MODE;
 941                 ahc_outb(ahc, SFUNCT, sfunct | ALT_MODE);
 942                 ahc->bus_softc.pci_softc.optionmode = ahc_inb(ahc, OPTIONMODE);
 943                 ahc->bus_softc.pci_softc.targcrccnt = ahc_inw(ahc, TARGCRCCNT);
 944                 ahc_outb(ahc, SFUNCT, sfunct);
 945                 ahc->bus_softc.pci_softc.crccontrol1 =
 946                     ahc_inb(ahc, CRCCONTROL1);
 947         }
 948         if ((ahc->features & AHC_MULTI_FUNC) != 0)
 949                 ahc->bus_softc.pci_softc.scbbaddr = ahc_inb(ahc, SCBBADDR);
 950
 951         if ((ahc->features & AHC_ULTRA2) != 0)
 952                 ahc->bus_softc.pci_softc.dff_thrsh = ahc_inb(ahc, DFF_THRSH);
 953
 954         /* Core initialization */
 955         error = ahc_init(ahc);
 956         if (error != 0)
 957                 return (error);
 958
 959         /*
 960          * Allow interrupts now that we are completely setup.
 961          */
 962         error = ahc_pci_map_int(ahc);
 963         if (error != 0)
 964                 return (error);
 965
 966         ahc->init_level++;
 967         return (0);
 968 }
 969
 970 /*
 971  * Test for the presense of external sram in an
 972  * "unshared" configuration.
 973  */
 974 static int
 975 ahc_ext_scbram_present(struct ahc_softc *ahc)
 976 {
 977         u_int chip;
 978         int ramps;
 979         int single_user;
 980         uint32_t devconfig;
 981
 982         chip = ahc->chip & AHC_CHIPID_MASK;
 983         devconfig = ahc_pci_read_config(ahc->dev_softc,
 984                                         DEVCONFIG, /*bytes*/4);
 985         single_user = (devconfig & MPORTMODE) != 0;
 986
 987         if ((ahc->features & AHC_ULTRA2) != 0)
 988                 ramps = (ahc_inb(ahc, DSCOMMAND0) & RAMPS) != 0;
 989         else if (chip == AHC_AIC7895 || chip == AHC_AIC7895C)
 990                 /*
 991                  * External SCBRAM arbitration is flakey
 992                  * on these chips.  Unfortunately this means
 993                  * we don't use the extra SCB ram space on the
 994                  * 3940AUW.
 995                  */
 996                 ramps = 0;
 997         else if (chip >= AHC_AIC7870)
 998                 ramps = (devconfig & RAMPSM) != 0;
 999         else
1000                 ramps = 0;
1001
1002         if (ramps && single_user)
1003                 return (1);
1004         return (0);
1005 }
1006
1007 /*
1008  * Enable external scbram.
1009  */
1010 static void
1011 ahc_scbram_config(struct ahc_softc *ahc, int enable, int pcheck,
1012                   int fast, int large)
1013 {
1014         uint32_t devconfig;
1015
1016         if (ahc->features & AHC_MULTI_FUNC) {
1017                 /*
1018                  * Set the SCB Base addr (highest address bit)
1019                  * depending on which channel we are.
1020                  */
1021                 ahc_outb(ahc, SCBBADDR, ahc_get_pci_function(ahc->dev_softc));
1022         }
1023
1024         ahc->flags &= ~AHC_LSCBS_ENABLED;
1025         if (large)
1026                 ahc->flags |= AHC_LSCBS_ENABLED;
1027         devconfig = ahc_pci_read_config(ahc->dev_softc, DEVCONFIG, /*bytes*/4);
1028         if ((ahc->features & AHC_ULTRA2) != 0) {
1029                 u_int dscommand0;
1030
1031                 dscommand0 = ahc_inb(ahc, DSCOMMAND0);
1032                 if (enable)
1033                         dscommand0 &= ~INTSCBRAMSEL;
1034                 else
1035                         dscommand0 |= INTSCBRAMSEL;
1036                 if (large)
1037                         dscommand0 &= ~USCBSIZE32;
1038                 else
1039                         dscommand0 |= USCBSIZE32;
1040                 ahc_outb(ahc, DSCOMMAND0, dscommand0);
1041         } else {
1042                 if (fast)
1043                         devconfig &= ~EXTSCBTIME;
1044                 else
1045                         devconfig |= EXTSCBTIME;
1046                 if (enable)
1047                         devconfig &= ~SCBRAMSEL;
1048                 else
1049                         devconfig |= SCBRAMSEL;
1050                 if (large)
1051                         devconfig &= ~SCBSIZE32;
1052                 else
1053                         devconfig |= SCBSIZE32;
1054         }
1055         if (pcheck)
1056                 devconfig |= EXTSCBPEN;
1057         else
1058                 devconfig &= ~EXTSCBPEN;
1059
1060         ahc_pci_write_config(ahc->dev_softc, DEVCONFIG, devconfig, /*bytes*/4);
1061 }
1062
1063 /*
1064  * Take a look to see if we have external SRAM.
1065  * We currently do not attempt to use SRAM that is
1066  * shared among multiple controllers.
1067  */
1068 static void
1069 ahc_probe_ext_scbram(struct ahc_softc *ahc)
1070 {
1071         int num_scbs;
1072         int test_num_scbs;
1073         int enable;
1074         int pcheck;
1075         int fast;
1076         int large;
1077
1078         enable = FALSE;
1079         pcheck = FALSE;
1080         fast = FALSE;
1081         large = FALSE;
1082         num_scbs = 0;
1083
1084         if (ahc_ext_scbram_present(ahc) == 0)
1085                 goto done;
1086
1087         /*
1088          * Probe for the best parameters to use.
1089          */
1090         ahc_scbram_config(ahc, /*enable*/TRUE, pcheck, fast, large);
1091         num_scbs = ahc_probe_scbs(ahc);
1092         if (num_scbs == 0) {
1093                 /* The SRAM wasn't really present. */
1094                 goto done;
1095         }
1096         enable = TRUE;
1097
1098         /*
1099          * Clear any outstanding parity error
1100          * and ensure that parity error reporting
1101          * is enabled.
1102          */
1103         ahc_outb(ahc, SEQCTL, 0);
1104         ahc_outb(ahc, CLRINT, CLRPARERR);
1105         ahc_outb(ahc, CLRINT, CLRBRKADRINT);
1106
1107         /* Now see if we can do parity */
1108         ahc_scbram_config(ahc, enable, /*pcheck*/TRUE, fast, large);
1109         num_scbs = ahc_probe_scbs(ahc);
1110         if ((ahc_inb(ahc, INTSTAT) & BRKADRINT) == 0
1111          || (ahc_inb(ahc, ERROR) & MPARERR) == 0)
1112                 pcheck = TRUE;
1113
1114         /* Clear any resulting parity error */
1115         ahc_outb(ahc, CLRINT, CLRPARERR);
1116         ahc_outb(ahc, CLRINT, CLRBRKADRINT);
1117
1118         /* Now see if we can do fast timing */
1119         ahc_scbram_config(ahc, enable, pcheck, /*fast*/TRUE, large);
1120         test_num_scbs = ahc_probe_scbs(ahc);
1121         if (test_num_scbs == num_scbs
1122          && ((ahc_inb(ahc, INTSTAT) & BRKADRINT) == 0
1123           || (ahc_inb(ahc, ERROR) & MPARERR) == 0))
1124                 fast = TRUE;
1125
1126         /*
1127          * See if we can use large SCBs and still maintain
1128          * the same overall count of SCBs.
1129          */
1130         if ((ahc->features & AHC_LARGE_SCBS) != 0) {
1131                 ahc_scbram_config(ahc, enable, pcheck, fast, /*large*/TRUE);
1132                 test_num_scbs = ahc_probe_scbs(ahc);
1133                 if (test_num_scbs >= num_scbs) {
1134                         large = TRUE;
1135                         num_scbs = test_num_scbs;
1136                         if (num_scbs >= 64) {
1137                                 /*
1138                                  * We have enough space to move the
1139                                  * "busy targets table" into SCB space
1140                                  * and make it qualify all the way to the
1141                                  * lun level.
1142                                  */
1143                                 ahc->flags |= AHC_SCB_BTT;
1144                         }
1145                 }
1146         }
1147 done:
1148         /*
1149          * Disable parity error reporting until we
1150          * can load instruction ram.
1151          */
1152         ahc_outb(ahc, SEQCTL, PERRORDIS|FAILDIS);
1153         /* Clear any latched parity error */
1154         ahc_outb(ahc, CLRINT, CLRPARERR);
1155         ahc_outb(ahc, CLRINT, CLRBRKADRINT);
1156         if (bootverbose && enable) {
1157                 printf("%s: External SRAM, %s access%s, %dbytes/SCB\n",
1158                        ahc_name(ahc), fast ? "fast" : "slow",
1159                        pcheck ? ", parity checking enabled" : "",
1160                        large ? 64 : 32);
1161         }
1162         ahc_scbram_config(ahc, enable, pcheck, fast, large);
1163 }
1164
1165 /*
1166  * Perform some simple tests that should catch situations where
1167  * our registers are invalidly mapped.
1168  */
1169 int
1170 ahc_pci_test_register_access(struct ahc_softc *ahc)
1171 {
1172         int      error;
1173         u_int    status1;
1174         uint32_t cmd;
1175         uint8_t  hcntrl;
1176
1177         error = EIO;
1178
1179         /*
1180          * Enable PCI error interrupt status, but suppress NMIs
1181          * generated by SERR raised due to target aborts.
1182          */
1183         cmd = ahc_pci_read_config(ahc->dev_softc, PCIR_COMMAND, /*bytes*/2);
1184         ahc_pci_write_config(ahc->dev_softc, PCIR_COMMAND,
1185                              cmd & ~PCIM_CMD_SERRESPEN, /*bytes*/2);
1186
1187         /*
1188          * First a simple test to see if any
1189          * registers can be read.  Reading
1190          * HCNTRL has no side effects and has
1191          * at least one bit that is guaranteed to
1192          * be zero so it is a good register to
1193          * use for this test.
1194          */
1195         hcntrl = ahc_inb(ahc, HCNTRL);
1196         if (hcntrl == 0xFF)
1197                 goto fail;
1198
1199         /*
1200          * Next create a situation where write combining
1201          * or read prefetching could be initiated by the
1202          * CPU or host bridge.  Our device does not support
1203          * either, so look for data corruption and/or flagged
1204          * PCI errors.  First pause without causing another
1205          * chip reset.
1206          */
1207         hcntrl &= ~CHIPRST;
1208         ahc_outb(ahc, HCNTRL, hcntrl|PAUSE);
1209         while (ahc_is_paused(ahc) == 0)
1210                 ;
1211
1212         /* Clear any PCI errors that occurred before our driver attached. */
1213         status1 = ahc_pci_read_config(ahc->dev_softc,
1214                                       PCIR_STATUS + 1, /*bytes*/1);
1215         ahc_pci_write_config(ahc->dev_softc, PCIR_STATUS + 1,
1216                              status1, /*bytes*/1);
1217         ahc_outb(ahc, CLRINT, CLRPARERR);
1218
1219         ahc_outb(ahc, SEQCTL, PERRORDIS);
1220         ahc_outb(ahc, SCBPTR, 0);
1221         ahc_outl(ahc, SCB_BASE, 0x5aa555aa);
1222         if (ahc_inl(ahc, SCB_BASE) != 0x5aa555aa)
1223                 goto fail;
1224
1225         status1 = ahc_pci_read_config(ahc->dev_softc,
1226                                       PCIR_STATUS + 1, /*bytes*/1);
1227         if ((status1 & STA) != 0)
1228                 goto fail;
1229
1230         error = 0;
1231
1232 fail:
1233         /* Silently clear any latched errors. */
1234         status1 = ahc_pci_read_config(ahc->dev_softc,
1235                                       PCIR_STATUS + 1, /*bytes*/1);
1236         ahc_pci_write_config(ahc->dev_softc, PCIR_STATUS + 1,
1237                              status1, /*bytes*/1);
1238         ahc_outb(ahc, CLRINT, CLRPARERR);
1239         ahc_outb(ahc, SEQCTL, PERRORDIS|FAILDIS);
1240         ahc_pci_write_config(ahc->dev_softc, PCIR_COMMAND, cmd, /*bytes*/2);
1241         return (error);
1242 }
1243
1244 /*
1245  * Check the external port logic for a serial eeprom
1246  * and termination/cable detection contrls.
1247  */
1248 static void
1249 check_extport(struct ahc_softc *ahc, u_int *sxfrctl1)
1250 {
1251         struct  seeprom_descriptor sd;
1252         struct  seeprom_config *sc;
1253         int     have_seeprom;
1254         int     have_autoterm;
1255
1256         sd.sd_ahc = ahc;
1257         sd.sd_control_offset = SEECTL;
1258         sd.sd_status_offset = SEECTL;
1259         sd.sd_dataout_offset = SEECTL;
1260         sc = ahc->seep_config;
1261
1262         /*
1263          * For some multi-channel devices, the c46 is simply too
1264          * small to work.  For the other controller types, we can
1265          * get our information from either SEEPROM type.  Set the
1266          * type to start our probe with accordingly.
1267          */
1268         if (ahc->flags & AHC_LARGE_SEEPROM)
1269                 sd.sd_chip = C56_66;
1270         else
1271                 sd.sd_chip = C46;
1272
1273         sd.sd_MS = SEEMS;
1274         sd.sd_RDY = SEERDY;
1275         sd.sd_CS = SEECS;
1276         sd.sd_CK = SEECK;
1277         sd.sd_DO = SEEDO;
1278         sd.sd_DI = SEEDI;
1279
1280         have_seeprom = ahc_acquire_seeprom(ahc, &sd);
1281         if (have_seeprom) {
1282
1283                 if (bootverbose)
1284                         printf("%s: Reading SEEPROM...", ahc_name(ahc));
1285
1286                 for (;;) {
1287                         u_int start_addr;
1288
1289                         start_addr = 32 * (ahc->channel - 'A');
1290
1291                         have_seeprom = ahc_read_seeprom(&sd, (uint16_t *)sc,
1292                                                         start_addr,
1293                                                         sizeof(*sc)/2);
1294
1295                         if (have_seeprom)
1296                                 have_seeprom = ahc_verify_cksum(sc);
1297
1298                         if (have_seeprom != 0 || sd.sd_chip == C56_66) {
1299                                 if (bootverbose) {
1300                                         if (have_seeprom == 0)
1301                                                 printf ("checksum error\n");
1302                                         else
1303                                                 printf ("done.\n");
1304                                 }
1305                                 break;
1306                         }
1307                         sd.sd_chip = C56_66;
1308                 }
1309                 ahc_release_seeprom(&sd);
1310         }
1311
1312         if (!have_seeprom) {
1313                 /*
1314                  * Pull scratch ram settings and treat them as
1315                  * if they are the contents of an seeprom if
1316                  * the 'ADPT' signature is found in SCB2.
1317                  * We manually compose the data as 16bit values
1318                  * to avoid endian issues.
1319                  */
1320                 ahc_outb(ahc, SCBPTR, 2);
1321                 if (ahc_inb(ahc, SCB_BASE) == 'A'
1322                  && ahc_inb(ahc, SCB_BASE + 1) == 'D'
1323                  && ahc_inb(ahc, SCB_BASE + 2) == 'P'
1324                  && ahc_inb(ahc, SCB_BASE + 3) == 'T') {
1325                         uint16_t *sc_data;
1326                         int       i;
1327
1328                         sc_data = (uint16_t *)sc;
1329                         for (i = 0; i < 32; i++, sc_data++) {
1330                                 int     j;
1331
1332                                 j = i * 2;
1333                                 *sc_data = ahc_inb(ahc, SRAM_BASE + j)
1334                                          | ahc_inb(ahc, SRAM_BASE + j + 1) << 8;
1335                         }
1336                         have_seeprom = ahc_verify_cksum(sc);
1337                         if (have_seeprom)
1338                                 ahc->flags |= AHC_SCB_CONFIG_USED;
1339                 }
1340                 /*
1341                  * Clear any SCB parity errors in case this data and
1342                  * its associated parity was not initialized by the BIOS
1343                  */
1344                 ahc_outb(ahc, CLRINT, CLRPARERR);
1345                 ahc_outb(ahc, CLRINT, CLRBRKADRINT);
1346         }
1347
1348         if (!have_seeprom) {
1349                 if (bootverbose)
1350                         printf("%s: No SEEPROM available.\n", ahc_name(ahc));
1351                 ahc->flags |= AHC_USEDEFAULTS;
1352                 free(ahc->seep_config, M_DEVBUF);
1353                 ahc->seep_config = NULL;
1354                 sc = NULL;
1355         } else {
1356                 ahc_parse_pci_eeprom(ahc, sc);
1357         }
1358
1359         /*
1360          * Cards that have the external logic necessary to talk to
1361          * a SEEPROM, are almost certain to have the remaining logic
1362          * necessary for auto-termination control.  This assumption
1363          * hasn't failed yet...
1364          */
1365         have_autoterm = have_seeprom;
1366
1367         /*
1368          * Some low-cost chips have SEEPROM and auto-term control built
1369          * in, instead of using a GAL.  They can tell us directly
1370          * if the termination logic is enabled.
1371          */
1372         if ((ahc->features & AHC_SPIOCAP) != 0) {
1373                 if ((ahc_inb(ahc, SPIOCAP) & SSPIOCPS) == 0)
1374                         have_autoterm = FALSE;
1375         }
1376
1377         if (have_autoterm) {
1378                 ahc->flags |= AHC_HAS_TERM_LOGIC;
1379                 ahc_acquire_seeprom(ahc, &sd);
1380                 configure_termination(ahc, &sd, sc->adapter_control, sxfrctl1);
1381                 ahc_release_seeprom(&sd);
1382         } else if (have_seeprom) {
1383                 *sxfrctl1 &= ~STPWEN;
1384                 if ((sc->adapter_control & CFSTERM) != 0)
1385                         *sxfrctl1 |= STPWEN;
1386                 if (bootverbose)
1387                         printf("%s: Low byte termination %sabled\n",
1388                                ahc_name(ahc),
1389                                (*sxfrctl1 & STPWEN) ? "en" : "dis");
1390         }
1391 }
1392
1393 static void
1394 ahc_parse_pci_eeprom(struct ahc_softc *ahc, struct seeprom_config *sc)
1395 {
1396         /*
1397          * Put the data we've collected down into SRAM
1398          * where ahc_init will find it.
1399          */
1400         int      i;
1401         int      max_targ = sc->max_targets & CFMAXTARG;
1402         u_int    scsi_conf;
1403         uint16_t discenable;
1404         uint16_t ultraenb;
1405
1406         discenable = 0;
1407         ultraenb = 0;
1408         if ((sc->adapter_control & CFULTRAEN) != 0) {
1409                 /*
1410                  * Determine if this adapter has a "newstyle"
1411                  * SEEPROM format.
1412                  */
1413                 for (i = 0; i < max_targ; i++) {
1414                         if ((sc->device_flags[i] & CFSYNCHISULTRA) != 0) {
1415                                 ahc->flags |= AHC_NEWEEPROM_FMT;
1416                                 break;
1417                         }
1418                 }
1419         }
1420
1421         for (i = 0; i < max_targ; i++) {
1422                 u_int     scsirate;
1423                 uint16_t target_mask;
1424
1425                 target_mask = 0x01 << i;
1426                 if (sc->device_flags[i] & CFDISC)
1427                         discenable |= target_mask;
1428                 if ((ahc->flags & AHC_NEWEEPROM_FMT) != 0) {
1429                         if ((sc->device_flags[i] & CFSYNCHISULTRA) != 0)
1430                                 ultraenb |= target_mask;
1431                 } else if ((sc->adapter_control & CFULTRAEN) != 0) {
1432                         ultraenb |= target_mask;
1433                 }
1434                 if ((sc->device_flags[i] & CFXFER) == 0x04
1435                  && (ultraenb & target_mask) != 0) {
1436                         /* Treat 10MHz as a non-ultra speed */
1437                         sc->device_flags[i] &= ~CFXFER;
1438                         ultraenb &= ~target_mask;
1439                 }
1440                 if ((ahc->features & AHC_ULTRA2) != 0) {
1441                         u_int offset;
1442
1443                         if (sc->device_flags[i] & CFSYNCH)
1444                                 offset = MAX_OFFSET_ULTRA2;
1445                         else
1446                                 offset = 0;
1447                         ahc_outb(ahc, TARG_OFFSET + i, offset);
1448
1449                         /*
1450                          * The ultra enable bits contain the
1451                          * high bit of the ultra2 sync rate
1452                          * field.
1453                          */
1454                         scsirate = (sc->device_flags[i] & CFXFER)
1455                                  | ((ultraenb & target_mask) ? 0x8 : 0x0);
1456                         if (sc->device_flags[i] & CFWIDEB)
1457                                 scsirate |= WIDEXFER;
1458                 } else {
1459                         scsirate = (sc->device_flags[i] & CFXFER) << 4;
1460                         if (sc->device_flags[i] & CFSYNCH)
1461                                 scsirate |= SOFS;
1462                         if (sc->device_flags[i] & CFWIDEB)
1463                                 scsirate |= WIDEXFER;
1464                 }
1465                 ahc_outb(ahc, TARG_SCSIRATE + i, scsirate);
1466         }
1467         ahc->our_id = sc->brtime_id & CFSCSIID;
1468
1469         scsi_conf = (ahc->our_id & 0x7);
1470         if (sc->adapter_control & CFSPARITY)
1471                 scsi_conf |= ENSPCHK;
1472         if (sc->adapter_control & CFRESETB)
1473                 scsi_conf |= RESET_SCSI;
1474
1475         ahc->flags |= (sc->adapter_control & CFBOOTCHAN) >> CFBOOTCHANSHIFT;
1476
1477         if (sc->bios_control & CFEXTEND)
1478                 ahc->flags |= AHC_EXTENDED_TRANS_A;
1479
1480         if (sc->bios_control & CFBIOSEN)
1481                 ahc->flags |= AHC_BIOS_ENABLED;
1482         if (ahc->features & AHC_ULTRA
1483          && (ahc->flags & AHC_NEWEEPROM_FMT) == 0) {
1484                 /* Should we enable Ultra mode? */
1485                 if (!(sc->adapter_control & CFULTRAEN))
1486                         /* Treat us as a non-ultra card */
1487                         ultraenb = 0;
1488         }
1489
1490         if (sc->signature == CFSIGNATURE
1491          || sc->signature == CFSIGNATURE2) {
1492                 uint32_t devconfig;
1493
1494                 /* Honor the STPWLEVEL settings */
1495                 devconfig = ahc_pci_read_config(ahc->dev_softc,
1496                                                 DEVCONFIG, /*bytes*/4);
1497                 devconfig &= ~STPWLEVEL;
1498                 if ((sc->bios_control & CFSTPWLEVEL) != 0)
1499                         devconfig |= STPWLEVEL;
1500                 ahc_pci_write_config(ahc->dev_softc, DEVCONFIG,
1501                                      devconfig, /*bytes*/4);
1502         }
1503         /* Set SCSICONF info */
1504         ahc_outb(ahc, SCSICONF, scsi_conf);
1505         ahc_outb(ahc, DISC_DSB, ~(discenable & 0xff));
1506         ahc_outb(ahc, DISC_DSB + 1, ~((discenable >> 8) & 0xff));
1507         ahc_outb(ahc, ULTRA_ENB, ultraenb & 0xff);
1508         ahc_outb(ahc, ULTRA_ENB + 1, (ultraenb >> 8) & 0xff);
1509 }
1510
1511 static void
1512 configure_termination(struct ahc_softc *ahc,
1513                       struct seeprom_descriptor *sd,
1514                       u_int adapter_control,
1515                       u_int *sxfrctl1)
1516 {
1517         uint8_t brddat;
1518
1519         brddat = 0;
1520
1521         /*
1522          * Update the settings in sxfrctl1 to match the
1523          * termination settings
1524          */
1525         *sxfrctl1 = 0;
1526
1527         /*
1528          * SEECS must be on for the GALS to latch
1529          * the data properly.  Be sure to leave MS
1530          * on or we will release the seeprom.
1531          */
1532         SEEPROM_OUTB(sd, sd->sd_MS | sd->sd_CS);
1533         if ((adapter_control & CFAUTOTERM) != 0
1534          || (ahc->features & AHC_NEW_TERMCTL) != 0) {
1535                 int internal50_present;
1536                 int internal68_present;
1537                 int externalcable_present;
1538                 int eeprom_present;
1539                 int enableSEC_low;
1540                 int enableSEC_high;
1541                 int enablePRI_low;
1542                 int enablePRI_high;
1543                 int sum;
1544
1545                 enableSEC_low = 0;
1546                 enableSEC_high = 0;
1547                 enablePRI_low = 0;
1548                 enablePRI_high = 0;
1549                 if ((ahc->features & AHC_NEW_TERMCTL) != 0) {
1550                         ahc_new_term_detect(ahc, &enableSEC_low,
1551                                             &enableSEC_high,
1552                                             &enablePRI_low,
1553                                             &enablePRI_high,
1554                                             &eeprom_present);
1555                         if ((adapter_control & CFSEAUTOTERM) == 0) {
1556                                 if (bootverbose)
1557                                         printf("%s: Manual SE Termination\n",
1558                                                ahc_name(ahc));
1559                                 enableSEC_low = (adapter_control & CFSELOWTERM);
1560                                 enableSEC_high =
1561                                     (adapter_control & CFSEHIGHTERM);
1562                         }
1563                         if ((adapter_control & CFAUTOTERM) == 0) {
1564                                 if (bootverbose)
1565                                         printf("%s: Manual LVD Termination\n",
1566                                                ahc_name(ahc));
1567                                 enablePRI_low = (adapter_control & CFSTERM);
1568                                 enablePRI_high = (adapter_control & CFWSTERM);
1569                         }
1570                         /* Make the table calculations below happy */
1571                         internal50_present = 0;
1572                         internal68_present = 1;
1573                         externalcable_present = 1;
1574                 } else if ((ahc->features & AHC_SPIOCAP) != 0) {
1575                         aic785X_cable_detect(ahc, &internal50_present,
1576                                              &externalcable_present,
1577                                              &eeprom_present);
1578                         /* Can never support a wide connector. */
1579                         internal68_present = 0;
1580                 } else {
1581                         aic787X_cable_detect(ahc, &internal50_present,
1582                                              &internal68_present,
1583                                              &externalcable_present,
1584                                              &eeprom_present);
1585                 }
1586
1587                 if ((ahc->features & AHC_WIDE) == 0)
1588                         internal68_present = 0;
1589
1590                 if (bootverbose
1591                  && (ahc->features & AHC_ULTRA2) == 0) {
1592                         printf("%s: internal 50 cable %s present",
1593                                ahc_name(ahc),
1594                                internal50_present ? "is":"not");
1595
1596                         if ((ahc->features & AHC_WIDE) != 0)
1597                                 printf(", internal 68 cable %s present",
1598                                        internal68_present ? "is":"not");
1599                         printf("\n%s: external cable %s present\n",
1600                                ahc_name(ahc),
1601                                externalcable_present ? "is":"not");
1602                 }
1603                 if (bootverbose)
1604                         printf("%s: BIOS eeprom %s present\n",
1605                                ahc_name(ahc), eeprom_present ? "is" : "not");
1606
1607                 if ((ahc->flags & AHC_INT50_SPEEDFLEX) != 0) {
1608                         /*
1609                          * The 50 pin connector is a separate bus,
1610                          * so force it to always be terminated.
1611                          * In the future, perform current sensing
1612                          * to determine if we are in the middle of
1613                          * a properly terminated bus.
1614                          */
1615                         internal50_present = 0;
1616                 }
1617
1618                 /*
1619                  * Now set the termination based on what
1620                  * we found.
1621                  * Flash Enable = BRDDAT7
1622                  * Secondary High Term Enable = BRDDAT6
1623                  * Secondary Low Term Enable = BRDDAT5 (7890)
1624                  * Primary High Term Enable = BRDDAT4 (7890)
1625                  */
1626                 if ((ahc->features & AHC_ULTRA2) == 0
1627                  && (internal50_present != 0)
1628                  && (internal68_present != 0)
1629                  && (externalcable_present != 0)) {
1630                         printf("%s: Illegal cable configuration!!. "
1631                                "Only two connectors on the "
1632                                "adapter may be used at a "
1633                                "time!\n", ahc_name(ahc));
1634
1635                         /*
1636                          * Pretend there are no cables in the hope
1637                          * that having all of the termination on
1638                          * gives us a more stable bus.
1639                          */
1640                         internal50_present = 0;
1641                         internal68_present = 0;
1642                         externalcable_present = 0;
1643                 }
1644
1645                 if ((ahc->features & AHC_WIDE) != 0
1646                  && ((externalcable_present == 0)
1647                   || (internal68_present == 0)
1648                   || (enableSEC_high != 0))) {
1649                         brddat |= BRDDAT6;
1650                         if (bootverbose) {
1651                                 if ((ahc->flags & AHC_INT50_SPEEDFLEX) != 0)
1652                                         printf("%s: 68 pin termination "
1653                                                "Enabled\n", ahc_name(ahc));
1654                                 else
1655                                         printf("%s: %sHigh byte termination "
1656                                                "Enabled\n", ahc_name(ahc),
1657                                                enableSEC_high ? "Secondary "
1658                                                               : "");
1659                         }
1660                 }
1661
1662                 sum = internal50_present + internal68_present
1663                     + externalcable_present;
1664                 if (sum < 2 || (enableSEC_low != 0)) {
1665                         if ((ahc->features & AHC_ULTRA2) != 0)
1666                                 brddat |= BRDDAT5;
1667                         else
1668                                 *sxfrctl1 |= STPWEN;
1669                         if (bootverbose) {
1670                                 if ((ahc->flags & AHC_INT50_SPEEDFLEX) != 0)
1671                                         printf("%s: 50 pin termination "
1672                                                "Enabled\n", ahc_name(ahc));
1673                                 else
1674                                         printf("%s: %sLow byte termination "
1675                                                "Enabled\n", ahc_name(ahc),
1676                                                enableSEC_low ? "Secondary "
1677                                                              : "");
1678                         }
1679                 }
1680
1681                 if (enablePRI_low != 0) {
1682                         *sxfrctl1 |= STPWEN;
1683                         if (bootverbose)
1684                                 printf("%s: Primary Low Byte termination "
1685                                        "Enabled\n", ahc_name(ahc));
1686                 }
1687
1688                 /*
1689                  * Setup STPWEN before setting up the rest of
1690                  * the termination per the tech note on the U160 cards.
1691                  */
1692                 ahc_outb(ahc, SXFRCTL1, *sxfrctl1);
1693
1694                 if (enablePRI_high != 0) {
1695                         brddat |= BRDDAT4;
1696                         if (bootverbose)
1697                                 printf("%s: Primary High Byte "
1698                                        "termination Enabled\n",
1699                                        ahc_name(ahc));
1700                 }
1701
1702                 write_brdctl(ahc, brddat);
1703
1704         } else {
1705                 if ((adapter_control & CFSTERM) != 0) {
1706                         *sxfrctl1 |= STPWEN;
1707
1708                         if (bootverbose)
1709                                 printf("%s: %sLow byte termination Enabled\n",
1710                                        ahc_name(ahc),
1711                                        (ahc->features & AHC_ULTRA2) ? "Primary "
1712                                                                     : "");
1713                 }
1714
1715                 if ((adapter_control & CFWSTERM) != 0
1716                  && (ahc->features & AHC_WIDE) != 0) {
1717                         brddat |= BRDDAT6;
1718                         if (bootverbose)
1719                                 printf("%s: %sHigh byte termination Enabled\n",
1720                                        ahc_name(ahc),
1721                                        (ahc->features & AHC_ULTRA2)
1722                                      ? "Secondary " : "");
1723                 }
1724
1725                 /*
1726                  * Setup STPWEN before setting up the rest of
1727                  * the termination per the tech note on the U160 cards.
1728                  */
1729                 ahc_outb(ahc, SXFRCTL1, *sxfrctl1);
1730
1731                 if ((ahc->features & AHC_WIDE) != 0)
1732                         write_brdctl(ahc, brddat);
1733         }
1734         SEEPROM_OUTB(sd, sd->sd_MS); /* Clear CS */
1735 }
1736
1737 static void
1738 ahc_new_term_detect(struct ahc_softc *ahc, int *enableSEC_low,
1739                     int *enableSEC_high, int *enablePRI_low,
1740                     int *enablePRI_high, int *eeprom_present)
1741 {
1742         uint8_t brdctl;
1743
1744         /*
1745          * BRDDAT7 = Eeprom
1746          * BRDDAT6 = Enable Secondary High Byte termination
1747          * BRDDAT5 = Enable Secondary Low Byte termination
1748          * BRDDAT4 = Enable Primary high byte termination
1749          * BRDDAT3 = Enable Primary low byte termination
1750          */
1751         brdctl = read_brdctl(ahc);
1752         *eeprom_present = brdctl & BRDDAT7;
1753         *enableSEC_high = (brdctl & BRDDAT6);
1754         *enableSEC_low = (brdctl & BRDDAT5);
1755         *enablePRI_high = (brdctl & BRDDAT4);
1756         *enablePRI_low = (brdctl & BRDDAT3);
1757 }
1758
1759 static void
1760 aic787X_cable_detect(struct ahc_softc *ahc, int *internal50_present,
1761                      int *internal68_present, int *externalcable_present,
1762                      int *eeprom_present)
1763 {
1764         uint8_t brdctl;
1765
1766         /*
1767          * First read the status of our cables.
1768          * Set the rom bank to 0 since the
1769          * bank setting serves as a multiplexor
1770          * for the cable detection logic.
1771          * BRDDAT5 controls the bank switch.
1772          */
1773         write_brdctl(ahc, 0);
1774
1775         /*
1776          * Now read the state of the internal
1777          * connectors.  BRDDAT6 is INT50 and
1778          * BRDDAT7 is INT68.
1779          */
1780         brdctl = read_brdctl(ahc);
1781         *internal50_present = (brdctl & BRDDAT6) ? 0 : 1;
1782         *internal68_present = (brdctl & BRDDAT7) ? 0 : 1;
1783
1784         /*
1785          * Set the rom bank to 1 and determine
1786          * the other signals.
1787          */
1788         write_brdctl(ahc, BRDDAT5);
1789
1790         /*
1791          * Now read the state of the external
1792          * connectors.  BRDDAT6 is EXT68 and
1793          * BRDDAT7 is EPROMPS.
1794          */
1795         brdctl = read_brdctl(ahc);
1796         *externalcable_present = (brdctl & BRDDAT6) ? 0 : 1;
1797         *eeprom_present = (brdctl & BRDDAT7) ? 1 : 0;
1798 }
1799
1800 static void
1801 aic785X_cable_detect(struct ahc_softc *ahc, int *internal50_present,
1802                      int *externalcable_present, int *eeprom_present)
1803 {
1804         uint8_t brdctl;
1805         uint8_t spiocap;
1806
1807         spiocap = ahc_inb(ahc, SPIOCAP);
1808         spiocap &= ~SOFTCMDEN;
1809         spiocap |= EXT_BRDCTL;
1810         ahc_outb(ahc, SPIOCAP, spiocap);
1811         ahc_outb(ahc, BRDCTL, BRDRW|BRDCS);
1812         ahc_flush_device_writes(ahc);
1813         ahc_delay(500);
1814         ahc_outb(ahc, BRDCTL, 0);
1815         ahc_flush_device_writes(ahc);
1816         ahc_delay(500);
1817         brdctl = ahc_inb(ahc, BRDCTL);
1818         *internal50_present = (brdctl & BRDDAT5) ? 0 : 1;
1819         *externalcable_present = (brdctl & BRDDAT6) ? 0 : 1;
1820         *eeprom_present = (ahc_inb(ahc, SPIOCAP) & EEPROM) ? 1 : 0;
1821 }
1822
1823 int
1824 ahc_acquire_seeprom(struct ahc_softc *ahc, struct seeprom_descriptor *sd)
1825 {
1826         int wait;
1827
1828         if ((ahc->features & AHC_SPIOCAP) != 0
1829          && (ahc_inb(ahc, SPIOCAP) & SEEPROM) == 0)
1830                 return (0);
1831
1832         /*
1833          * Request access of the memory port.  When access is
1834          * granted, SEERDY will go high.  We use a 1 second
1835          * timeout which should be near 1 second more than
1836          * is needed.  Reason: after the chip reset, there
1837          * should be no contention.
1838          */
1839         SEEPROM_OUTB(sd, sd->sd_MS);
1840         wait = 1000;  /* 1 second timeout in msec */
1841         while (--wait && ((SEEPROM_STATUS_INB(sd) & sd->sd_RDY) == 0)) {
1842                 ahc_delay(1000);  /* delay 1 msec */
1843         }
1844         if ((SEEPROM_STATUS_INB(sd) & sd->sd_RDY) == 0) {
1845                 SEEPROM_OUTB(sd, 0);
1846                 return (0);
1847         }
1848         return(1);
1849 }
1850
1851 void
1852 ahc_release_seeprom(struct seeprom_descriptor *sd)
1853 {
1854         /* Release access to the memory port and the serial EEPROM. */
1855         SEEPROM_OUTB(sd, 0);
1856 }
1857
1858 static void
1859 write_brdctl(struct ahc_softc *ahc, uint8_t value)
1860 {
1861         uint8_t brdctl;
1862
1863         if ((ahc->chip & AHC_CHIPID_MASK) == AHC_AIC7895) {
1864                 brdctl = BRDSTB;
1865                 if (ahc->channel == 'B')
1866                         brdctl |= BRDCS;
1867         } else if ((ahc->features & AHC_ULTRA2) != 0) {
1868                 brdctl = 0;
1869         } else {
1870                 brdctl = BRDSTB|BRDCS;
1871         }
1872         ahc_outb(ahc, BRDCTL, brdctl);
1873         ahc_flush_device_writes(ahc);
1874         brdctl |= value;
1875         ahc_outb(ahc, BRDCTL, brdctl);
1876         ahc_flush_device_writes(ahc);
1877         if ((ahc->features & AHC_ULTRA2) != 0)
1878                 brdctl |= BRDSTB_ULTRA2;
1879         else
1880                 brdctl &= ~BRDSTB;
1881         ahc_outb(ahc, BRDCTL, brdctl);
1882         ahc_flush_device_writes(ahc);
1883         if ((ahc->features & AHC_ULTRA2) != 0)
1884                 brdctl = 0;
1885         else
1886                 brdctl &= ~BRDCS;
1887         ahc_outb(ahc, BRDCTL, brdctl);
1888 }
1889
1890 static uint8_t
1891 read_brdctl(struct ahc_softc *ahc)
1892 {
1893         uint8_t brdctl;
1894         uint8_t value;
1895
1896         if ((ahc->chip & AHC_CHIPID_MASK) == AHC_AIC7895) {
1897                 brdctl = BRDRW;
1898                 if (ahc->channel == 'B')
1899                         brdctl |= BRDCS;
1900         } else if ((ahc->features & AHC_ULTRA2) != 0) {
1901                 brdctl = BRDRW_ULTRA2;
1902         } else {
1903                 brdctl = BRDRW|BRDCS;
1904         }
1905         ahc_outb(ahc, BRDCTL, brdctl);
1906         ahc_flush_device_writes(ahc);
1907         value = ahc_inb(ahc, BRDCTL);
1908         ahc_outb(ahc, BRDCTL, 0);
1909         return (value);
1910 }
1911
1912 static void
1913 ahc_pci_intr(struct ahc_softc *ahc)
1914 {
1915         u_int error;
1916         u_int status1;
1917
1918         error = ahc_inb(ahc, ERROR);
1919         if ((error & PCIERRSTAT) == 0)
1920                 return;
1921
1922         status1 = ahc_pci_read_config(ahc->dev_softc,
1923                                       PCIR_STATUS + 1, /*bytes*/1);
1924
1925         printf("%s: PCI error Interrupt at seqaddr = 0x%x\n",
1926               ahc_name(ahc),
1927               ahc_inb(ahc, SEQADDR0) | (ahc_inb(ahc, SEQADDR1) << 8));
1928
1929         if (status1 & DPE) {
1930                 ahc->pci_target_perr_count++;
1931                 printf("%s: Data Parity Error Detected during address "
1932                        "or write data phase\n", ahc_name(ahc));
1933         }
1934         if (status1 & SSE) {
1935                 printf("%s: Signal System Error Detected\n", ahc_name(ahc));
1936         }
1937         if (status1 & RMA) {
1938                 printf("%s: Received a Master Abort\n", ahc_name(ahc));
1939         }
1940         if (status1 & RTA) {
1941                 printf("%s: Received a Target Abort\n", ahc_name(ahc));
1942         }
1943         if (status1 & STA) {
1944                 printf("%s: Signaled a Target Abort\n", ahc_name(ahc));
1945         }
1946         if (status1 & DPR) {
1947                 printf("%s: Data Parity Error has been reported via PERR#\n",
1948                        ahc_name(ahc));
1949         }
1950
1951         /* Clear latched errors. */
1952         ahc_pci_write_config(ahc->dev_softc, PCIR_STATUS + 1,
1953                              status1, /*bytes*/1);
1954
1955         if ((status1 & (DPE|SSE|RMA|RTA|STA|DPR)) == 0) {
1956                 printf("%s: Latched PCIERR interrupt with "
1957                        "no status bits set\n", ahc_name(ahc));
1958         } else {
1959                 ahc_outb(ahc, CLRINT, CLRPARERR);
1960         }
1961
1962         if (ahc->pci_target_perr_count > AHC_PCI_TARGET_PERR_THRESH) {
1963                 printf(
1964 "%s: WARNING WARNING WARNING WARNING\n"
1965 "%s: Too many PCI parity errors observed as a target.\n"
1966 "%s: Some device on this bus is generating bad parity.\n"
1967 "%s: This is an error *observed by*, not *generated by*, this controller.\n"
1968 "%s: PCI parity error checking has been disabled.\n"
1969 "%s: WARNING WARNING WARNING WARNING\n",
1970                        ahc_name(ahc), ahc_name(ahc), ahc_name(ahc),
1971                        ahc_name(ahc), ahc_name(ahc), ahc_name(ahc));
1972                 ahc->seqctl |= FAILDIS;
1973                 ahc_outb(ahc, SEQCTL, ahc->seqctl);
1974         }
1975         ahc_unpause(ahc);
1976 }
1977
1978 static int
1979 ahc_pci_chip_init(struct ahc_softc *ahc)
1980 {
1981         ahc_outb(ahc, DSCOMMAND0, ahc->bus_softc.pci_softc.dscommand0);
1982         ahc_outb(ahc, DSPCISTATUS, ahc->bus_softc.pci_softc.dspcistatus);
1983         if ((ahc->features & AHC_DT) != 0) {
1984                 u_int sfunct;
1985
1986                 sfunct = ahc_inb(ahc, SFUNCT) & ~ALT_MODE;
1987                 ahc_outb(ahc, SFUNCT, sfunct | ALT_MODE);
1988                 ahc_outb(ahc, OPTIONMODE, ahc->bus_softc.pci_softc.optionmode);
1989                 ahc_outw(ahc, TARGCRCCNT, ahc->bus_softc.pci_softc.targcrccnt);
1990                 ahc_outb(ahc, SFUNCT, sfunct);
1991                 ahc_outb(ahc, CRCCONTROL1,
1992                          ahc->bus_softc.pci_softc.crccontrol1);
1993         }
1994         if ((ahc->features & AHC_MULTI_FUNC) != 0)
1995                 ahc_outb(ahc, SCBBADDR, ahc->bus_softc.pci_softc.scbbaddr);
1996
1997         if ((ahc->features & AHC_ULTRA2) != 0)
1998                 ahc_outb(ahc, DFF_THRSH, ahc->bus_softc.pci_softc.dff_thrsh);
1999
2000         return (ahc_chip_init(ahc));
2001 }
2002
2003 static int
2004 ahc_pci_suspend(struct ahc_softc *ahc)
2005 {
2006         return (ahc_suspend(ahc));
2007 }
2008
2009 static int
2010 ahc_pci_resume(struct ahc_softc *ahc)
2011 {
2012
2013         pci_set_power_state(ahc->dev_softc, AHC_POWER_STATE_D0);
2014
2015         /*
2016          * We assume that the OS has restored our register
2017          * mappings, etc.  Just update the config space registers
2018          * that the OS doesn't know about and rely on our chip
2019          * reset handler to handle the rest.
2020          */
2021         ahc_pci_write_config(ahc->dev_softc, DEVCONFIG, /*bytes*/4,
2022                              ahc->bus_softc.pci_softc.devconfig);
2023         ahc_pci_write_config(ahc->dev_softc, PCIR_COMMAND, /*bytes*/1,
2024                              ahc->bus_softc.pci_softc.command);
2025         ahc_pci_write_config(ahc->dev_softc, CSIZE_LATTIME, /*bytes*/1,
2026                              ahc->bus_softc.pci_softc.csize_lattime);
2027         if ((ahc->flags & AHC_HAS_TERM_LOGIC) != 0) {
2028                 struct  seeprom_descriptor sd;
2029                 u_int   sxfrctl1;
2030
2031                 sd.sd_ahc = ahc;
2032                 sd.sd_control_offset = SEECTL;
2033                 sd.sd_status_offset = SEECTL;
2034                 sd.sd_dataout_offset = SEECTL;
2035
2036                 ahc_acquire_seeprom(ahc, &sd);
2037                 configure_termination(ahc, &sd,
2038                                       ahc->seep_config->adapter_control,
2039                                       &sxfrctl1);
2040                 ahc_release_seeprom(&sd);
2041         }
2042         return (ahc_resume(ahc));
2043 }
2044
2045 static int
2046 ahc_aic785X_setup(struct ahc_softc *ahc)
2047 {
2048         ahc_dev_softc_t pci;
2049         uint8_t rev;
2050
2051         pci = ahc->dev_softc;
2052         ahc->channel = 'A';
2053         ahc->chip = AHC_AIC7850;
2054         ahc->features = AHC_AIC7850_FE;
2055         ahc->bugs |= AHC_TMODE_WIDEODD_BUG|AHC_CACHETHEN_BUG|AHC_PCI_MWI_BUG;
2056         rev = ahc_pci_read_config(pci, PCIR_REVID, /*bytes*/1);
2057         if (rev >= 1)
2058                 ahc->bugs |= AHC_PCI_2_1_RETRY_BUG;
2059         ahc->instruction_ram_size = 512;
2060         return (0);
2061 }
2062
2063 static int
2064 ahc_aic7860_setup(struct ahc_softc *ahc)
2065 {
2066         ahc_dev_softc_t pci;
2067         uint8_t rev;
2068
2069         pci = ahc->dev_softc;
2070         ahc->channel = 'A';
2071         ahc->chip = AHC_AIC7860;
2072         ahc->features = AHC_AIC7860_FE;
2073         ahc->bugs |= AHC_TMODE_WIDEODD_BUG|AHC_CACHETHEN_BUG|AHC_PCI_MWI_BUG;
2074         rev = ahc_pci_read_config(pci, PCIR_REVID, /*bytes*/1);
2075         if (rev >= 1)
2076                 ahc->bugs |= AHC_PCI_2_1_RETRY_BUG;
2077         ahc->instruction_ram_size = 512;
2078         return (0);
2079 }
2080
2081 static int
2082 ahc_apa1480_setup(struct ahc_softc *ahc)
2083 {
2084         int error;
2085
2086         error = ahc_aic7860_setup(ahc);
2087         if (error != 0)
2088                 return (error);
2089         ahc->features |= AHC_REMOVABLE;
2090         return (0);
2091 }
2092
2093 static int
2094 ahc_aic7870_setup(struct ahc_softc *ahc)
2095 {
2096
2097         ahc->channel = 'A';
2098         ahc->chip = AHC_AIC7870;
2099         ahc->features = AHC_AIC7870_FE;
2100         ahc->bugs |= AHC_TMODE_WIDEODD_BUG|AHC_CACHETHEN_BUG|AHC_PCI_MWI_BUG;
2101         ahc->instruction_ram_size = 512;
2102         return (0);
2103 }
2104
2105 static int
2106 ahc_aha394X_setup(struct ahc_softc *ahc)
2107 {
2108         int error;
2109
2110         error = ahc_aic7870_setup(ahc);
2111         if (error == 0)
2112                 error = ahc_aha394XX_setup(ahc);
2113         return (error);
2114 }
2115
2116 static int
2117 ahc_aha398X_setup(struct ahc_softc *ahc)
2118 {
2119         int error;
2120
2121         error = ahc_aic7870_setup(ahc);
2122         if (error == 0)
2123                 error = ahc_aha398XX_setup(ahc);
2124         return (error);
2125 }
2126
2127 static int
2128 ahc_aha494X_setup(struct ahc_softc *ahc)
2129 {
2130         int error;
2131
2132         error = ahc_aic7870_setup(ahc);
2133         if (error == 0)
2134                 error = ahc_aha494XX_setup(ahc);
2135         return (error);
2136 }
2137
2138 static int
2139 ahc_aic7880_setup(struct ahc_softc *ahc)
2140 {
2141         ahc_dev_softc_t pci;
2142         uint8_t rev;
2143
2144         pci = ahc->dev_softc;
2145         ahc->channel = 'A';
2146         ahc->chip = AHC_AIC7880;
2147         ahc->features = AHC_AIC7880_FE;
2148         ahc->bugs |= AHC_TMODE_WIDEODD_BUG;
2149         rev = ahc_pci_read_config(pci, PCIR_REVID, /*bytes*/1);
2150         if (rev >= 1) {
2151                 ahc->bugs |= AHC_PCI_2_1_RETRY_BUG;
2152         } else {
2153                 ahc->bugs |= AHC_CACHETHEN_BUG|AHC_PCI_MWI_BUG;
2154         }
2155         ahc->instruction_ram_size = 512;
2156         return (0);
2157 }
2158
2159 static int
2160 ahc_aha2940Pro_setup(struct ahc_softc *ahc)
2161 {
2162
2163         ahc->flags |= AHC_INT50_SPEEDFLEX;
2164         return (ahc_aic7880_setup(ahc));
2165 }
2166
2167 static int
2168 ahc_aha394XU_setup(struct ahc_softc *ahc)
2169 {
2170         int error;
2171
2172         error = ahc_aic7880_setup(ahc);
2173         if (error == 0)
2174                 error = ahc_aha394XX_setup(ahc);
2175         return (error);
2176 }
2177
2178 static int
2179 ahc_aha398XU_setup(struct ahc_softc *ahc)
2180 {
2181         int error;
2182
2183         error = ahc_aic7880_setup(ahc);
2184         if (error == 0)
2185                 error = ahc_aha398XX_setup(ahc);
2186         return (error);
2187 }
2188
2189 static int
2190 ahc_aic7890_setup(struct ahc_softc *ahc)
2191 {
2192         ahc_dev_softc_t pci;
2193         uint8_t rev;
2194
2195         pci = ahc->dev_softc;
2196         ahc->channel = 'A';
2197         ahc->chip = AHC_AIC7890;
2198         ahc->features = AHC_AIC7890_FE;
2199         ahc->flags |= AHC_NEWEEPROM_FMT;
2200         rev = ahc_pci_read_config(pci, PCIR_REVID, /*bytes*/1);
2201         if (rev == 0)
2202                 ahc->bugs |= AHC_AUTOFLUSH_BUG|AHC_CACHETHEN_BUG;
2203         ahc->instruction_ram_size = 768;
2204         return (0);
2205 }
2206
2207 static int
2208 ahc_aic7892_setup(struct ahc_softc *ahc)
2209 {
2210
2211         ahc->channel = 'A';
2212         ahc->chip = AHC_AIC7892;
2213         ahc->features = AHC_AIC7892_FE;
2214         ahc->flags |= AHC_NEWEEPROM_FMT;
2215         ahc->bugs |= AHC_SCBCHAN_UPLOAD_BUG;
2216         ahc->instruction_ram_size = 1024;
2217         return (0);
2218 }
2219
2220 static int
2221 ahc_aic7895_setup(struct ahc_softc *ahc)
2222 {
2223         ahc_dev_softc_t pci;
2224         uint8_t rev;
2225
2226         pci = ahc->dev_softc;
2227         ahc->channel = ahc_get_pci_function(pci) == 1 ? 'B' : 'A';
2228         /*
2229          * The 'C' revision of the aic7895 has a few additional features.
2230          */
2231         rev = ahc_pci_read_config(pci, PCIR_REVID, /*bytes*/1);
2232         if (rev >= 4) {
2233                 ahc->chip = AHC_AIC7895C;
2234                 ahc->features = AHC_AIC7895C_FE;
2235         } else  {
2236                 u_int command;
2237
2238                 ahc->chip = AHC_AIC7895;
2239                 ahc->features = AHC_AIC7895_FE;
2240
2241                 /*
2242                  * The BIOS disables the use of MWI transactions
2243                  * since it does not have the MWI bug work around
2244                  * we have.  Disabling MWI reduces performance, so
2245                  * turn it on again.
2246                  */
2247                 command = ahc_pci_read_config(pci, PCIR_COMMAND, /*bytes*/1);
2248                 command |= PCIM_CMD_MWRICEN;
2249                 ahc_pci_write_config(pci, PCIR_COMMAND, command, /*bytes*/1);
2250                 ahc->bugs |= AHC_PCI_MWI_BUG;
2251         }
2252         /*
2253          * XXX Does CACHETHEN really not work???  What about PCI retry?
2254          * on C level chips.  Need to test, but for now, play it safe.
2255          */
2256         ahc->bugs |= AHC_TMODE_WIDEODD_BUG|AHC_PCI_2_1_RETRY_BUG
2257                   |  AHC_CACHETHEN_BUG;
2258
2259 #if 0
2260         uint32_t devconfig;
2261
2262         /*
2263          * Cachesize must also be zero due to stray DAC
2264          * problem when sitting behind some bridges.
2265          */
2266         ahc_pci_write_config(pci, CSIZE_LATTIME, 0, /*bytes*/1);
2267         devconfig = ahc_pci_read_config(pci, DEVCONFIG, /*bytes*/1);
2268         devconfig |= MRDCEN;
2269         ahc_pci_write_config(pci, DEVCONFIG, devconfig, /*bytes*/1);
2270 #endif
2271         ahc->flags |= AHC_NEWEEPROM_FMT;
2272         ahc->instruction_ram_size = 512;
2273         return (0);
2274 }
2275
2276 static int
2277 ahc_aic7896_setup(struct ahc_softc *ahc)
2278 {
2279         ahc_dev_softc_t pci;
2280
2281         pci = ahc->dev_softc;
2282         ahc->channel = ahc_get_pci_function(pci) == 1 ? 'B' : 'A';
2283         ahc->chip = AHC_AIC7896;
2284         ahc->features = AHC_AIC7896_FE;
2285         ahc->flags |= AHC_NEWEEPROM_FMT;
2286         ahc->bugs |= AHC_CACHETHEN_DIS_BUG;
2287         ahc->instruction_ram_size = 768;
2288         return (0);
2289 }
2290
2291 static int
2292 ahc_aic7899_setup(struct ahc_softc *ahc)
2293 {
2294         ahc_dev_softc_t pci;
2295
2296         pci = ahc->dev_softc;
2297         ahc->channel = ahc_get_pci_function(pci) == 1 ? 'B' : 'A';
2298         ahc->chip = AHC_AIC7899;
2299         ahc->features = AHC_AIC7899_FE;
2300         ahc->flags |= AHC_NEWEEPROM_FMT;
2301         ahc->bugs |= AHC_SCBCHAN_UPLOAD_BUG;
2302         ahc->instruction_ram_size = 1024;
2303         return (0);
2304 }
2305
2306 static int
2307 ahc_aha29160C_setup(struct ahc_softc *ahc)
2308 {
2309         int error;
2310
2311         error = ahc_aic7899_setup(ahc);
2312         if (error != 0)
2313                 return (error);
2314         ahc->features |= AHC_REMOVABLE;
2315         return (0);
2316 }
2317
2318 static int
2319 ahc_raid_setup(struct ahc_softc *ahc)
2320 {
2321         printf("RAID functionality unsupported\n");
2322         return (ENXIO);
2323 }
2324
2325 static int
2326 ahc_aha394XX_setup(struct ahc_softc *ahc)
2327 {
2328         ahc_dev_softc_t pci;
2329
2330         pci = ahc->dev_softc;
2331         switch (ahc_get_pci_slot(pci)) {
2332         case AHC_394X_SLOT_CHANNEL_A:
2333                 ahc->channel = 'A';
2334                 break;
2335         case AHC_394X_SLOT_CHANNEL_B:
2336                 ahc->channel = 'B';
2337                 break;
2338         default:
2339                 printf("adapter at unexpected slot %d\n"
2340                        "unable to map to a channel\n",
2341                        ahc_get_pci_slot(pci));
2342                 ahc->channel = 'A';
2343         }
2344         return (0);
2345 }
2346
2347 static int
2348 ahc_aha398XX_setup(struct ahc_softc *ahc)
2349 {
2350         ahc_dev_softc_t pci;
2351
2352         pci = ahc->dev_softc;
2353         switch (ahc_get_pci_slot(pci)) {
2354         case AHC_398X_SLOT_CHANNEL_A:
2355                 ahc->channel = 'A';
2356                 break;
2357         case AHC_398X_SLOT_CHANNEL_B:
2358                 ahc->channel = 'B';
2359                 break;
2360         case AHC_398X_SLOT_CHANNEL_C:
2361                 ahc->channel = 'C';
2362                 break;
2363         default:
2364                 printf("adapter at unexpected slot %d\n"
2365                        "unable to map to a channel\n",
2366                        ahc_get_pci_slot(pci));
2367                 ahc->channel = 'A';
2368                 break;
2369         }
2370         ahc->flags |= AHC_LARGE_SEEPROM;
2371         return (0);
2372 }
2373
2374 static int
2375 ahc_aha494XX_setup(struct ahc_softc *ahc)
2376 {
2377         ahc_dev_softc_t pci;
2378
2379         pci = ahc->dev_softc;
2380         switch (ahc_get_pci_slot(pci)) {
2381         case AHC_494X_SLOT_CHANNEL_A:
2382                 ahc->channel = 'A';
2383                 break;
2384         case AHC_494X_SLOT_CHANNEL_B:
2385                 ahc->channel = 'B';
2386                 break;
2387         case AHC_494X_SLOT_CHANNEL_C:
2388                 ahc->channel = 'C';
2389                 break;
2390         case AHC_494X_SLOT_CHANNEL_D:
2391                 ahc->channel = 'D';
2392                 break;
2393         default:
2394                 printf("adapter at unexpected slot %d\n"
2395                        "unable to map to a channel\n",
2396                        ahc_get_pci_slot(pci));
2397                 ahc->channel = 'A';
2398         }
2399         ahc->flags |= AHC_LARGE_SEEPROM;
2400         return (0);
2401 }