1 /*******************************************************************************
3 Intel(R) Gigabit Ethernet Linux driver
4 Copyright(c) 2007-2009 Intel Corporation.
6 This program is free software; you can redistribute it and/or modify it
7 under the terms and conditions of the GNU General Public License,
8 version 2, as published by the Free Software Foundation.
10 This program is distributed in the hope it will be useful, but WITHOUT
11 ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
12 FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for
15 You should have received a copy of the GNU General Public License along with
16 this program; if not, write to the Free Software Foundation, Inc.,
17 51 Franklin St - Fifth Floor, Boston, MA 02110-1301 USA.
19 The full GNU General Public License is included in this distribution in
20 the file called "COPYING".
23 e1000-devel Mailing List <e1000-devel@lists.sourceforge.net>
24 Intel Corporation, 5200 N.E. Elam Young Parkway, Hillsboro, OR 97124-6497
26 *******************************************************************************/
28 #ifndef _E1000_DEFINES_H_
29 #define _E1000_DEFINES_H_
31 /* Number of Transmit and Receive Descriptors must be a multiple of 8 */
32 #define REQ_TX_DESCRIPTOR_MULTIPLE 8
33 #define REQ_RX_DESCRIPTOR_MULTIPLE 8
35 /* Definitions for power management and wakeup registers */
37 #define E1000_WUC_PME_EN 0x00000002 /* PME Enable */
39 /* Wake Up Filter Control */
40 #define E1000_WUFC_LNKC 0x00000001 /* Link Status Change Wakeup Enable */
41 #define E1000_WUFC_MAG 0x00000002 /* Magic Packet Wakeup Enable */
42 #define E1000_WUFC_EX 0x00000004 /* Directed Exact Wakeup Enable */
43 #define E1000_WUFC_MC 0x00000008 /* Directed Multicast Wakeup Enable */
44 #define E1000_WUFC_BC 0x00000010 /* Broadcast Wakeup Enable */
46 /* Extended Device Control */
47 #define E1000_CTRL_EXT_SDP7_DATA 0x00000080 /* Value of SW Defineable Pin 7 */
48 /* Physical Func Reset Done Indication */
49 #define E1000_CTRL_EXT_PFRSTD 0x00004000
50 #define E1000_CTRL_EXT_LINK_MODE_MASK 0x00C00000
51 #define E1000_CTRL_EXT_LINK_MODE_PCIE_SERDES 0x00C00000
52 #define E1000_CTRL_EXT_LINK_MODE_SGMII 0x00800000
53 #define E1000_CTRL_EXT_EIAME 0x01000000
54 #define E1000_CTRL_EXT_IRCA 0x00000001
55 /* Interrupt delay cancellation */
56 /* Driver loaded bit for FW */
57 #define E1000_CTRL_EXT_DRV_LOAD 0x10000000
58 /* Interrupt acknowledge Auto-mask */
59 /* Clear Interrupt timers after IMS clear */
60 /* packet buffer parity error detection enabled */
61 /* descriptor FIFO parity error detection enable */
62 #define E1000_CTRL_EXT_PBA_CLR 0x80000000 /* PBA Clear */
63 #define E1000_I2CCMD_REG_ADDR_SHIFT 16
64 #define E1000_I2CCMD_PHY_ADDR_SHIFT 24
65 #define E1000_I2CCMD_OPCODE_READ 0x08000000
66 #define E1000_I2CCMD_OPCODE_WRITE 0x00000000
67 #define E1000_I2CCMD_READY 0x20000000
68 #define E1000_I2CCMD_ERROR 0x80000000
69 #define E1000_MAX_SGMII_PHY_REG_ADDR 255
70 #define E1000_I2CCMD_PHY_TIMEOUT 200
71 #define E1000_IVAR_VALID 0x80
72 #define E1000_GPIE_NSICR 0x00000001
73 #define E1000_GPIE_MSIX_MODE 0x00000010
74 #define E1000_GPIE_EIAME 0x40000000
75 #define E1000_GPIE_PBA 0x80000000
77 /* Receive Descriptor bit definitions */
78 #define E1000_RXD_STAT_DD 0x01 /* Descriptor Done */
79 #define E1000_RXD_STAT_EOP 0x02 /* End of Packet */
80 #define E1000_RXD_STAT_IXSM 0x04 /* Ignore checksum */
81 #define E1000_RXD_STAT_VP 0x08 /* IEEE VLAN Packet */
82 #define E1000_RXD_STAT_UDPCS 0x10 /* UDP xsum calculated */
83 #define E1000_RXD_STAT_TCPCS 0x20 /* TCP xsum calculated */
84 #define E1000_RXD_STAT_TS 0x10000 /* Pkt was time stamped */
86 #define E1000_RXDEXT_STATERR_CE 0x01000000
87 #define E1000_RXDEXT_STATERR_SE 0x02000000
88 #define E1000_RXDEXT_STATERR_SEQ 0x04000000
89 #define E1000_RXDEXT_STATERR_CXE 0x10000000
90 #define E1000_RXDEXT_STATERR_TCPE 0x20000000
91 #define E1000_RXDEXT_STATERR_IPE 0x40000000
92 #define E1000_RXDEXT_STATERR_RXE 0x80000000
94 /* Same mask, but for extended and packet split descriptors */
95 #define E1000_RXDEXT_ERR_FRAME_ERR_MASK ( \
96 E1000_RXDEXT_STATERR_CE | \
97 E1000_RXDEXT_STATERR_SE | \
98 E1000_RXDEXT_STATERR_SEQ | \
99 E1000_RXDEXT_STATERR_CXE | \
100 E1000_RXDEXT_STATERR_RXE)
102 #define E1000_MRQC_RSS_FIELD_IPV4_TCP 0x00010000
103 #define E1000_MRQC_RSS_FIELD_IPV4 0x00020000
104 #define E1000_MRQC_RSS_FIELD_IPV6_TCP_EX 0x00040000
105 #define E1000_MRQC_RSS_FIELD_IPV6 0x00100000
106 #define E1000_MRQC_RSS_FIELD_IPV6_TCP 0x00200000
109 /* Management Control */
110 #define E1000_MANC_SMBUS_EN 0x00000001 /* SMBus Enabled - RO */
111 #define E1000_MANC_ASF_EN 0x00000002 /* ASF Enabled - RO */
112 /* Enable Neighbor Discovery Filtering */
113 #define E1000_MANC_RCV_TCO_EN 0x00020000 /* Receive TCO Packets Enabled */
114 #define E1000_MANC_BLK_PHY_RST_ON_IDE 0x00040000 /* Block phy resets */
115 /* Enable MAC address filtering */
116 #define E1000_MANC_EN_MAC_ADDR_FILTER 0x00100000
118 /* Receive Control */
119 #define E1000_RCTL_EN 0x00000002 /* enable */
120 #define E1000_RCTL_SBP 0x00000004 /* store bad packet */
121 #define E1000_RCTL_UPE 0x00000008 /* unicast promiscuous enable */
122 #define E1000_RCTL_MPE 0x00000010 /* multicast promiscuous enab */
123 #define E1000_RCTL_LPE 0x00000020 /* long packet enable */
124 #define E1000_RCTL_LBM_MAC 0x00000040 /* MAC loopback mode */
125 #define E1000_RCTL_LBM_TCVR 0x000000C0 /* tcvr loopback mode */
126 #define E1000_RCTL_RDMTS_HALF 0x00000000 /* rx desc min threshold size */
127 #define E1000_RCTL_MO_SHIFT 12 /* multicast offset shift */
128 #define E1000_RCTL_BAM 0x00008000 /* broadcast enable */
129 #define E1000_RCTL_SZ_512 0x00020000 /* rx buffer size 512 */
130 #define E1000_RCTL_SZ_256 0x00030000 /* rx buffer size 256 */
131 #define E1000_RCTL_VFE 0x00040000 /* vlan filter enable */
132 #define E1000_RCTL_CFIEN 0x00080000 /* canonical form enable */
133 #define E1000_RCTL_SECRC 0x04000000 /* Strip Ethernet CRC */
136 * Use byte values for the following shift parameters
138 * psrctl |= (((ROUNDUP(value0, 128) >> E1000_PSRCTL_BSIZE0_SHIFT) &
139 * E1000_PSRCTL_BSIZE0_MASK) |
140 * ((ROUNDUP(value1, 1024) >> E1000_PSRCTL_BSIZE1_SHIFT) &
141 * E1000_PSRCTL_BSIZE1_MASK) |
142 * ((ROUNDUP(value2, 1024) << E1000_PSRCTL_BSIZE2_SHIFT) &
143 * E1000_PSRCTL_BSIZE2_MASK) |
144 * ((ROUNDUP(value3, 1024) << E1000_PSRCTL_BSIZE3_SHIFT) |;
145 * E1000_PSRCTL_BSIZE3_MASK))
146 * where value0 = [128..16256], default=256
147 * value1 = [1024..64512], default=4096
148 * value2 = [0..64512], default=4096
149 * value3 = [0..64512], default=0
152 #define E1000_PSRCTL_BSIZE0_MASK 0x0000007F
153 #define E1000_PSRCTL_BSIZE1_MASK 0x00003F00
154 #define E1000_PSRCTL_BSIZE2_MASK 0x003F0000
155 #define E1000_PSRCTL_BSIZE3_MASK 0x3F000000
157 #define E1000_PSRCTL_BSIZE0_SHIFT 7 /* Shift _right_ 7 */
158 #define E1000_PSRCTL_BSIZE1_SHIFT 2 /* Shift _right_ 2 */
159 #define E1000_PSRCTL_BSIZE2_SHIFT 6 /* Shift _left_ 6 */
160 #define E1000_PSRCTL_BSIZE3_SHIFT 14 /* Shift _left_ 14 */
162 /* SWFW_SYNC Definitions */
163 #define E1000_SWFW_EEP_SM 0x1
164 #define E1000_SWFW_PHY0_SM 0x2
165 #define E1000_SWFW_PHY1_SM 0x4
167 /* FACTPS Definitions */
169 #define E1000_CTRL_FD 0x00000001 /* Full duplex.0=half; 1=full */
170 #define E1000_CTRL_GIO_MASTER_DISABLE 0x00000004 /*Blocks new Master requests */
171 #define E1000_CTRL_LRST 0x00000008 /* Link reset. 0=normal,1=reset */
172 #define E1000_CTRL_ASDE 0x00000020 /* Auto-speed detect enable */
173 #define E1000_CTRL_SLU 0x00000040 /* Set link up (Force Link) */
174 #define E1000_CTRL_ILOS 0x00000080 /* Invert Loss-Of Signal */
175 #define E1000_CTRL_SPD_SEL 0x00000300 /* Speed Select Mask */
176 #define E1000_CTRL_SPD_100 0x00000100 /* Force 100Mb */
177 #define E1000_CTRL_SPD_1000 0x00000200 /* Force 1Gb */
178 #define E1000_CTRL_FRCSPD 0x00000800 /* Force Speed */
179 #define E1000_CTRL_FRCDPX 0x00001000 /* Force Duplex */
180 /* Defined polarity of Dock/Undock indication in SDP[0] */
181 /* Reset both PHY ports, through PHYRST_N pin */
182 /* enable link status from external LINK_0 and LINK_1 pins */
183 #define E1000_CTRL_SWDPIN0 0x00040000 /* SWDPIN 0 value */
184 #define E1000_CTRL_SWDPIN1 0x00080000 /* SWDPIN 1 value */
185 #define E1000_CTRL_SWDPIO0 0x00400000 /* SWDPIN 0 Input or output */
186 #define E1000_CTRL_RST 0x04000000 /* Global reset */
187 #define E1000_CTRL_RFCE 0x08000000 /* Receive Flow Control enable */
188 #define E1000_CTRL_TFCE 0x10000000 /* Transmit flow control enable */
189 #define E1000_CTRL_VME 0x40000000 /* IEEE VLAN mode enable */
190 #define E1000_CTRL_PHY_RST 0x80000000 /* PHY Reset */
191 /* Initiate an interrupt to manageability engine */
192 #define E1000_CTRL_I2C_ENA 0x02000000 /* I2C enable */
194 /* Bit definitions for the Management Data IO (MDIO) and Management Data
195 * Clock (MDC) pins in the Device Control Register.
198 #define E1000_CONNSW_ENRGSRC 0x4
199 #define E1000_PCS_CFG_PCS_EN 8
200 #define E1000_PCS_LCTL_FLV_LINK_UP 1
201 #define E1000_PCS_LCTL_FSV_100 2
202 #define E1000_PCS_LCTL_FSV_1000 4
203 #define E1000_PCS_LCTL_FDV_FULL 8
204 #define E1000_PCS_LCTL_FSD 0x10
205 #define E1000_PCS_LCTL_FORCE_LINK 0x20
206 #define E1000_PCS_LCTL_FORCE_FCTRL 0x80
207 #define E1000_PCS_LCTL_AN_ENABLE 0x10000
208 #define E1000_PCS_LCTL_AN_RESTART 0x20000
209 #define E1000_PCS_LCTL_AN_TIMEOUT 0x40000
210 #define E1000_ENABLE_SERDES_LOOPBACK 0x0410
212 #define E1000_PCS_LSTS_LINK_OK 1
213 #define E1000_PCS_LSTS_SPEED_100 2
214 #define E1000_PCS_LSTS_SPEED_1000 4
215 #define E1000_PCS_LSTS_DUPLEX_FULL 8
216 #define E1000_PCS_LSTS_SYNK_OK 0x10
219 #define E1000_STATUS_FD 0x00000001 /* Full duplex.0=half,1=full */
220 #define E1000_STATUS_LU 0x00000002 /* Link up.0=no,1=link */
221 #define E1000_STATUS_FUNC_MASK 0x0000000C /* PCI Function Mask */
222 #define E1000_STATUS_FUNC_SHIFT 2
223 #define E1000_STATUS_FUNC_1 0x00000004 /* Function 1 */
224 #define E1000_STATUS_TXOFF 0x00000010 /* transmission paused */
225 #define E1000_STATUS_SPEED_100 0x00000040 /* Speed 100Mb/s */
226 #define E1000_STATUS_SPEED_1000 0x00000080 /* Speed 1000Mb/s */
227 /* Change in Dock/Undock state. Clear on write '0'. */
228 /* Status of Master requests. */
229 #define E1000_STATUS_GIO_MASTER_ENABLE 0x00080000
230 /* BMC external code execution disabled */
232 /* Constants used to intrepret the masked PCI-X bus speed. */
235 #define SPEED_100 100
236 #define SPEED_1000 1000
237 #define HALF_DUPLEX 1
238 #define FULL_DUPLEX 2
241 #define ADVERTISE_10_HALF 0x0001
242 #define ADVERTISE_10_FULL 0x0002
243 #define ADVERTISE_100_HALF 0x0004
244 #define ADVERTISE_100_FULL 0x0008
245 #define ADVERTISE_1000_HALF 0x0010 /* Not used, just FYI */
246 #define ADVERTISE_1000_FULL 0x0020
248 /* 1000/H is not supported, nor spec-compliant. */
249 #define E1000_ALL_SPEED_DUPLEX (ADVERTISE_10_HALF | ADVERTISE_10_FULL | \
250 ADVERTISE_100_HALF | ADVERTISE_100_FULL | \
252 #define E1000_ALL_NOT_GIG (ADVERTISE_10_HALF | ADVERTISE_10_FULL | \
253 ADVERTISE_100_HALF | ADVERTISE_100_FULL)
254 #define E1000_ALL_100_SPEED (ADVERTISE_100_HALF | ADVERTISE_100_FULL)
255 #define E1000_ALL_10_SPEED (ADVERTISE_10_HALF | ADVERTISE_10_FULL)
256 #define E1000_ALL_FULL_DUPLEX (ADVERTISE_10_FULL | ADVERTISE_100_FULL | \
258 #define E1000_ALL_HALF_DUPLEX (ADVERTISE_10_HALF | ADVERTISE_100_HALF)
260 #define AUTONEG_ADVERTISE_SPEED_DEFAULT E1000_ALL_SPEED_DUPLEX
263 #define E1000_LEDCTL_LED0_MODE_SHIFT 0
264 #define E1000_LEDCTL_LED0_BLINK 0x00000080
266 #define E1000_LEDCTL_MODE_LED_ON 0xE
267 #define E1000_LEDCTL_MODE_LED_OFF 0xF
269 /* Transmit Descriptor bit definitions */
270 #define E1000_TXD_POPTS_IXSM 0x01 /* Insert IP checksum */
271 #define E1000_TXD_POPTS_TXSM 0x02 /* Insert TCP/UDP checksum */
272 #define E1000_TXD_CMD_EOP 0x01000000 /* End of Packet */
273 #define E1000_TXD_CMD_IFCS 0x02000000 /* Insert FCS (Ethernet CRC) */
274 #define E1000_TXD_CMD_RS 0x08000000 /* Report Status */
275 #define E1000_TXD_CMD_DEXT 0x20000000 /* Descriptor extension (0 = legacy) */
276 #define E1000_TXD_STAT_DD 0x00000001 /* Descriptor Done */
277 /* Extended desc bits for Linksec and timesync */
279 /* Transmit Control */
280 #define E1000_TCTL_EN 0x00000002 /* enable tx */
281 #define E1000_TCTL_PSP 0x00000008 /* pad short packets */
282 #define E1000_TCTL_CT 0x00000ff0 /* collision threshold */
283 #define E1000_TCTL_COLD 0x003ff000 /* collision distance */
284 #define E1000_TCTL_RTLC 0x01000000 /* Re-transmit on late collision */
286 /* Transmit Arbitration Count */
289 #define E1000_SCTL_DISABLE_SERDES_LOOPBACK 0x0400
291 /* Receive Checksum Control */
292 #define E1000_RXCSUM_IPOFL 0x00000100 /* IPv4 checksum offload */
293 #define E1000_RXCSUM_TUOFL 0x00000200 /* TCP / UDP checksum offload */
294 #define E1000_RXCSUM_CRCOFL 0x00000800 /* CRC32 offload enable */
295 #define E1000_RXCSUM_PCSD 0x00002000 /* packet checksum disabled */
297 /* Header split receive */
298 #define E1000_RFCTL_LEF 0x00040000
300 /* Collision related configuration parameters */
301 #define E1000_COLLISION_THRESHOLD 15
302 #define E1000_CT_SHIFT 4
303 #define E1000_COLLISION_DISTANCE 63
304 #define E1000_COLD_SHIFT 12
306 /* Ethertype field values */
307 #define ETHERNET_IEEE_VLAN_TYPE 0x8100 /* 802.3ac packet */
309 #define MAX_JUMBO_FRAME_SIZE 0x3F00
312 #define E1000_PBA_34K 0x0022
313 #define E1000_PBA_64K 0x0040 /* 64KB */
319 #define MIN_NUM_XMITS 1000
321 /* SW Semaphore Register */
322 #define E1000_SWSM_SMBI 0x00000001 /* Driver Semaphore bit */
323 #define E1000_SWSM_SWESMBI 0x00000002 /* FW Semaphore bit */
325 /* Interrupt Cause Read */
326 #define E1000_ICR_TXDW 0x00000001 /* Transmit desc written back */
327 #define E1000_ICR_LSC 0x00000004 /* Link Status Change */
328 #define E1000_ICR_RXSEQ 0x00000008 /* rx sequence error */
329 #define E1000_ICR_RXDMT0 0x00000010 /* rx desc min. threshold (0) */
330 #define E1000_ICR_RXT0 0x00000080 /* rx timer intr (ring 0) */
331 #define E1000_ICR_VMMB 0x00000100 /* VM MB event */
332 /* If this bit asserted, the driver should claim the interrupt */
333 #define E1000_ICR_INT_ASSERTED 0x80000000
334 /* LAN connected device generates an interrupt */
335 #define E1000_ICR_DOUTSYNC 0x10000000 /* NIC DMA out of sync */
337 /* Extended Interrupt Cause Read */
338 #define E1000_EICR_RX_QUEUE0 0x00000001 /* Rx Queue 0 Interrupt */
339 #define E1000_EICR_RX_QUEUE1 0x00000002 /* Rx Queue 1 Interrupt */
340 #define E1000_EICR_RX_QUEUE2 0x00000004 /* Rx Queue 2 Interrupt */
341 #define E1000_EICR_RX_QUEUE3 0x00000008 /* Rx Queue 3 Interrupt */
342 #define E1000_EICR_TX_QUEUE0 0x00000100 /* Tx Queue 0 Interrupt */
343 #define E1000_EICR_TX_QUEUE1 0x00000200 /* Tx Queue 1 Interrupt */
344 #define E1000_EICR_TX_QUEUE2 0x00000400 /* Tx Queue 2 Interrupt */
345 #define E1000_EICR_TX_QUEUE3 0x00000800 /* Tx Queue 3 Interrupt */
346 #define E1000_EICR_OTHER 0x80000000 /* Interrupt Cause Active */
350 * This defines the bits that are set in the Interrupt Mask
351 * Set/Read Register. Each bit is documented below:
352 * o RXT0 = Receiver Timer Interrupt (ring 0)
353 * o TXDW = Transmit Descriptor Written Back
354 * o RXDMT0 = Receive Descriptor Minimum Threshold hit (ring 0)
355 * o RXSEQ = Receive Sequence Error
356 * o LSC = Link Status Change
358 #define IMS_ENABLE_MASK ( \
366 /* Interrupt Mask Set */
367 #define E1000_IMS_TXDW E1000_ICR_TXDW /* Transmit desc written back */
368 #define E1000_IMS_LSC E1000_ICR_LSC /* Link Status Change */
369 #define E1000_IMS_VMMB E1000_ICR_VMMB /* Mail box activity */
370 #define E1000_IMS_RXSEQ E1000_ICR_RXSEQ /* rx sequence error */
371 #define E1000_IMS_RXDMT0 E1000_ICR_RXDMT0 /* rx desc min. threshold */
372 #define E1000_IMS_RXT0 E1000_ICR_RXT0 /* rx timer intr */
373 #define E1000_IMS_DOUTSYNC E1000_ICR_DOUTSYNC /* NIC DMA out of sync */
375 /* Extended Interrupt Mask Set */
376 #define E1000_EIMS_OTHER E1000_EICR_OTHER /* Interrupt Cause Active */
378 /* Interrupt Cause Set */
379 #define E1000_ICS_LSC E1000_ICR_LSC /* Link Status Change */
380 #define E1000_ICS_RXDMT0 E1000_ICR_RXDMT0 /* rx desc min. threshold */
382 /* Extended Interrupt Cause Set */
384 /* Transmit Descriptor Control */
385 /* Enable the counting of descriptors still to be processed. */
387 /* Flow Control Constants */
388 #define FLOW_CONTROL_ADDRESS_LOW 0x00C28001
389 #define FLOW_CONTROL_ADDRESS_HIGH 0x00000100
390 #define FLOW_CONTROL_TYPE 0x8808
392 /* 802.1q VLAN Packet Size */
393 #define VLAN_TAG_SIZE 4 /* 802.3ac tag (not DMA'd) */
394 #define E1000_VLAN_FILTER_TBL_SIZE 128 /* VLAN Filter Table (4096 bits) */
396 /* Receive Address */
398 * Number of high/low register pairs in the RAR. The RAR (Receive Address
399 * Registers) holds the directed and multicast addresses that we monitor.
400 * Technically, we have 16 spots. However, we reserve one of these spots
401 * (RAR[15]) for our directed address used by controllers with
402 * manageability enabled, allowing us room for 15 multicast addresses.
404 #define E1000_RAH_AV 0x80000000 /* Receive descriptor valid */
405 #define E1000_RAL_MAC_ADDR_LEN 4
406 #define E1000_RAH_MAC_ADDR_LEN 2
407 #define E1000_RAH_POOL_MASK 0x03FC0000
408 #define E1000_RAH_POOL_1 0x00040000
411 #define E1000_ERR_NVM 1
412 #define E1000_ERR_PHY 2
413 #define E1000_ERR_CONFIG 3
414 #define E1000_ERR_PARAM 4
415 #define E1000_ERR_MAC_INIT 5
416 #define E1000_ERR_RESET 9
417 #define E1000_ERR_MASTER_REQUESTS_PENDING 10
418 #define E1000_BLK_PHY_RESET 12
419 #define E1000_ERR_SWFW_SYNC 13
420 #define E1000_NOT_IMPLEMENTED 14
421 #define E1000_ERR_MBX 15
423 /* Loop limit on how long we wait for auto-negotiation to complete */
424 #define COPPER_LINK_UP_LIMIT 10
425 #define PHY_AUTO_NEG_LIMIT 45
426 #define PHY_FORCE_LIMIT 20
427 /* Number of 100 microseconds we wait for PCI Express master disable */
428 #define MASTER_DISABLE_TIMEOUT 800
429 /* Number of milliseconds we wait for PHY configuration done after MAC reset */
430 #define PHY_CFG_TIMEOUT 100
431 /* Number of 2 milliseconds we wait for acquiring MDIO ownership. */
432 /* Number of milliseconds for NVM auto read done after MAC reset. */
433 #define AUTO_READ_DONE_TIMEOUT 10
436 #define E1000_FCRTL_XONE 0x80000000 /* Enable XON frame transmission */
438 /* PHY Control Register */
439 #define MII_CR_FULL_DUPLEX 0x0100 /* FDX =1, half duplex =0 */
440 #define MII_CR_RESTART_AUTO_NEG 0x0200 /* Restart auto negotiation */
441 #define MII_CR_AUTO_NEG_EN 0x1000 /* Auto Neg Enable */
442 #define MII_CR_LOOPBACK 0x4000 /* 0 = normal, 1 = loopback */
443 #define MII_CR_RESET 0x8000 /* 0 = normal, 1 = PHY reset */
444 #define MII_CR_SPEED_1000 0x0040
445 #define MII_CR_SPEED_100 0x2000
446 #define MII_CR_SPEED_10 0x0000
448 /* PHY Status Register */
449 #define MII_SR_LINK_STATUS 0x0004 /* Link Status 1 = link */
450 #define MII_SR_AUTONEG_COMPLETE 0x0020 /* Auto Neg Complete */
452 /* Autoneg Advertisement Register */
453 #define NWAY_AR_10T_HD_CAPS 0x0020 /* 10T Half Duplex Capable */
454 #define NWAY_AR_10T_FD_CAPS 0x0040 /* 10T Full Duplex Capable */
455 #define NWAY_AR_100TX_HD_CAPS 0x0080 /* 100TX Half Duplex Capable */
456 #define NWAY_AR_100TX_FD_CAPS 0x0100 /* 100TX Full Duplex Capable */
457 #define NWAY_AR_PAUSE 0x0400 /* Pause operation desired */
458 #define NWAY_AR_ASM_DIR 0x0800 /* Asymmetric Pause Direction bit */
460 /* Link Partner Ability Register (Base Page) */
461 #define NWAY_LPAR_PAUSE 0x0400 /* LP Pause operation desired */
462 #define NWAY_LPAR_ASM_DIR 0x0800 /* LP Asymmetric Pause Direction bit */
464 /* Autoneg Expansion Register */
466 /* 1000BASE-T Control Register */
467 #define CR_1000T_HD_CAPS 0x0100 /* Advertise 1000T HD capability */
468 #define CR_1000T_FD_CAPS 0x0200 /* Advertise 1000T FD capability */
469 #define CR_1000T_MS_VALUE 0x0800 /* 1=Configure PHY as Master */
470 /* 0=Configure PHY as Slave */
471 #define CR_1000T_MS_ENABLE 0x1000 /* 1=Master/Slave manual config value */
472 /* 0=Automatic Master/Slave config */
474 /* 1000BASE-T Status Register */
475 #define SR_1000T_REMOTE_RX_STATUS 0x1000 /* Remote receiver OK */
476 #define SR_1000T_LOCAL_RX_STATUS 0x2000 /* Local receiver OK */
479 /* PHY 1000 MII Register/Bit Definitions */
480 /* PHY Registers defined by IEEE */
481 #define PHY_CONTROL 0x00 /* Control Register */
482 #define PHY_STATUS 0x01 /* Status Register */
483 #define PHY_ID1 0x02 /* Phy Id Reg (word 1) */
484 #define PHY_ID2 0x03 /* Phy Id Reg (word 2) */
485 #define PHY_AUTONEG_ADV 0x04 /* Autoneg Advertisement */
486 #define PHY_LP_ABILITY 0x05 /* Link Partner Ability (Base Page) */
487 #define PHY_1000T_CTRL 0x09 /* 1000Base-T Control Reg */
488 #define PHY_1000T_STATUS 0x0A /* 1000Base-T Status Reg */
491 #define E1000_EECD_SK 0x00000001 /* NVM Clock */
492 #define E1000_EECD_CS 0x00000002 /* NVM Chip Select */
493 #define E1000_EECD_DI 0x00000004 /* NVM Data In */
494 #define E1000_EECD_DO 0x00000008 /* NVM Data Out */
495 #define E1000_EECD_REQ 0x00000040 /* NVM Access Request */
496 #define E1000_EECD_GNT 0x00000080 /* NVM Access Grant */
497 #define E1000_EECD_PRES 0x00000100 /* NVM Present */
498 /* NVM Addressing bits based on type 0=small, 1=large */
499 #define E1000_EECD_ADDR_BITS 0x00000400
500 #define E1000_NVM_GRANT_ATTEMPTS 1000 /* NVM # attempts to gain grant */
501 #define E1000_EECD_AUTO_RD 0x00000200 /* NVM Auto Read done */
502 #define E1000_EECD_SIZE_EX_MASK 0x00007800 /* NVM Size */
503 #define E1000_EECD_SIZE_EX_SHIFT 11
505 /* Offset to data in NVM read/write registers */
506 #define E1000_NVM_RW_REG_DATA 16
507 #define E1000_NVM_RW_REG_DONE 2 /* Offset to READ/WRITE done bit */
508 #define E1000_NVM_RW_REG_START 1 /* Start operation */
509 #define E1000_NVM_RW_ADDR_SHIFT 2 /* Shift to the address bits */
510 #define E1000_NVM_POLL_READ 0 /* Flag for polling for read complete */
512 /* NVM Word Offsets */
513 #define NVM_ID_LED_SETTINGS 0x0004
514 /* For SERDES output amplitude adjustment. */
515 #define NVM_INIT_CONTROL2_REG 0x000F
516 #define NVM_INIT_CONTROL3_PORT_B 0x0014
517 #define NVM_INIT_CONTROL3_PORT_A 0x0024
518 #define NVM_ALT_MAC_ADDR_PTR 0x0037
519 #define NVM_CHECKSUM_REG 0x003F
521 #define E1000_NVM_CFG_DONE_PORT_0 0x40000 /* MNG config cycle done */
522 #define E1000_NVM_CFG_DONE_PORT_1 0x80000 /* ...for second port */
524 /* Mask bits for fields in Word 0x0f of the NVM */
525 #define NVM_WORD0F_PAUSE_MASK 0x3000
526 #define NVM_WORD0F_ASM_DIR 0x2000
528 /* Mask bits for fields in Word 0x1a of the NVM */
530 /* For checksumming, the sum of all words in the NVM should equal 0xBABA. */
531 #define NVM_SUM 0xBABA
533 #define NVM_PBA_OFFSET_0 8
534 #define NVM_PBA_OFFSET_1 9
535 #define NVM_WORD_SIZE_BASE_SHIFT 6
537 /* NVM Commands - Microwire */
539 /* NVM Commands - SPI */
540 #define NVM_MAX_RETRY_SPI 5000 /* Max wait of 5ms, for RDY signal */
541 #define NVM_WRITE_OPCODE_SPI 0x02 /* NVM write opcode */
542 #define NVM_A8_OPCODE_SPI 0x08 /* opcode bit-3 = address bit-8 */
543 #define NVM_WREN_OPCODE_SPI 0x06 /* NVM set Write Enable latch */
544 #define NVM_RDSR_OPCODE_SPI 0x05 /* NVM read Status register */
546 /* SPI NVM Status Register */
547 #define NVM_STATUS_RDY_SPI 0x01
549 /* Word definitions for ID LED Settings */
550 #define ID_LED_RESERVED_0000 0x0000
551 #define ID_LED_RESERVED_FFFF 0xFFFF
552 #define ID_LED_DEFAULT ((ID_LED_OFF1_ON2 << 12) | \
553 (ID_LED_OFF1_OFF2 << 8) | \
554 (ID_LED_DEF1_DEF2 << 4) | \
556 #define ID_LED_DEF1_DEF2 0x1
557 #define ID_LED_DEF1_ON2 0x2
558 #define ID_LED_DEF1_OFF2 0x3
559 #define ID_LED_ON1_DEF2 0x4
560 #define ID_LED_ON1_ON2 0x5
561 #define ID_LED_ON1_OFF2 0x6
562 #define ID_LED_OFF1_DEF2 0x7
563 #define ID_LED_OFF1_ON2 0x8
564 #define ID_LED_OFF1_OFF2 0x9
566 #define IGP_ACTIVITY_LED_MASK 0xFFFFF0FF
567 #define IGP_ACTIVITY_LED_ENABLE 0x0300
568 #define IGP_LED3_MODE 0x07000000
570 /* PCI/PCI-X/PCI-EX Config space */
571 #define PCIE_LINK_STATUS 0x12
573 #define PCIE_LINK_WIDTH_MASK 0x3F0
574 #define PCIE_LINK_WIDTH_SHIFT 4
576 #define PHY_REVISION_MASK 0xFFFFFFF0
577 #define MAX_PHY_REG_ADDRESS 0x1F /* 5 bit address bus (0-0x1F) */
578 #define MAX_PHY_MULTI_PAGE_REG 0xF
580 /* Bit definitions for valid PHY IDs. */
585 #define M88E1111_I_PHY_ID 0x01410CC0
586 #define IGP03E1000_E_PHY_ID 0x02A80390
587 #define M88_VENDOR 0x0141
589 /* M88E1000 Specific Registers */
590 #define M88E1000_PHY_SPEC_CTRL 0x10 /* PHY Specific Control Register */
591 #define M88E1000_PHY_SPEC_STATUS 0x11 /* PHY Specific Status Register */
592 #define M88E1000_EXT_PHY_SPEC_CTRL 0x14 /* Extended PHY Specific Control */
594 #define M88E1000_PHY_PAGE_SELECT 0x1D /* Reg 29 for page number setting */
595 #define M88E1000_PHY_GEN_CONTROL 0x1E /* Its meaning depends on reg 29 */
597 /* M88E1000 PHY Specific Control Register */
598 #define M88E1000_PSCR_POLARITY_REVERSAL 0x0002 /* 1=Polarity Reversal enabled */
599 /* 1=CLK125 low, 0=CLK125 toggling */
600 #define M88E1000_PSCR_MDI_MANUAL_MODE 0x0000 /* MDI Crossover Mode bits 6:5 */
601 /* Manual MDI configuration */
602 #define M88E1000_PSCR_MDIX_MANUAL_MODE 0x0020 /* Manual MDIX configuration */
603 /* 1000BASE-T: Auto crossover, 100BASE-TX/10BASE-T: MDI Mode */
604 #define M88E1000_PSCR_AUTO_X_1000T 0x0040
605 /* Auto crossover enabled all speeds */
606 #define M88E1000_PSCR_AUTO_X_MODE 0x0060
608 * 1=Enable Extended 10BASE-T distance (Lower 10BASE-T Rx Threshold
609 * 0=Normal 10BASE-T Rx Threshold
611 /* 1=5-bit interface in 100BASE-TX, 0=MII interface in 100BASE-TX */
612 #define M88E1000_PSCR_ASSERT_CRS_ON_TX 0x0800 /* 1=Assert CRS on Transmit */
614 /* M88E1000 PHY Specific Status Register */
615 #define M88E1000_PSSR_REV_POLARITY 0x0002 /* 1=Polarity reversed */
616 #define M88E1000_PSSR_DOWNSHIFT 0x0020 /* 1=Downshifted */
617 #define M88E1000_PSSR_MDIX 0x0040 /* 1=MDIX; 0=MDI */
625 #define M88E1000_PSSR_CABLE_LENGTH 0x0380
626 #define M88E1000_PSSR_SPEED 0xC000 /* Speed, bits 14:15 */
627 #define M88E1000_PSSR_1000MBS 0x8000 /* 10=1000Mbs */
629 #define M88E1000_PSSR_CABLE_LENGTH_SHIFT 7
631 /* M88E1000 Extended PHY Specific Control Register */
633 * 1 = Lost lock detect enabled.
634 * Will assert lost lock and bring
635 * link down if idle not seen
636 * within 1ms in 1000BASE-T
639 * Number of times we will attempt to autonegotiate before downshifting if we
642 #define M88E1000_EPSCR_MASTER_DOWNSHIFT_MASK 0x0C00
643 #define M88E1000_EPSCR_MASTER_DOWNSHIFT_1X 0x0000
645 * Number of times we will attempt to autonegotiate before downshifting if we
648 #define M88E1000_EPSCR_SLAVE_DOWNSHIFT_MASK 0x0300
649 #define M88E1000_EPSCR_SLAVE_DOWNSHIFT_1X 0x0100
650 #define M88E1000_EPSCR_TX_CLK_25 0x0070 /* 25 MHz TX_CLK */
652 /* M88EC018 Rev 2 specific DownShift settings */
653 #define M88EC018_EPSCR_DOWNSHIFT_COUNTER_MASK 0x0E00
654 #define M88EC018_EPSCR_DOWNSHIFT_COUNTER_5X 0x0800
657 #define E1000_MDIC_REG_SHIFT 16
658 #define E1000_MDIC_PHY_SHIFT 21
659 #define E1000_MDIC_OP_WRITE 0x04000000
660 #define E1000_MDIC_OP_READ 0x08000000
661 #define E1000_MDIC_READY 0x10000000
662 #define E1000_MDIC_ERROR 0x40000000
665 #define E1000_GEN_CTL_READY 0x80000000
666 #define E1000_GEN_CTL_ADDRESS_SHIFT 8
667 #define E1000_GEN_POLL_TIMEOUT 640
669 #define E1000_VFTA_ENTRY_SHIFT 5
670 #define E1000_VFTA_ENTRY_MASK 0x7F
671 #define E1000_VFTA_ENTRY_BIT_SHIFT_MASK 0x1F
projects / linux-2.6 / blob