git.oblomov.eu Git - linux-2.6/blob - drivers/net/chelsio/my3126.c

   1 /* $Date: 2005/11/12 02:13:49 $ $RCSfile: my3126.c,v $ $Revision: 1.15 $ */
   2 #include "cphy.h"
   3 #include "elmer0.h"
   4 #include "suni1x10gexp_regs.h"
   5
   6 /* Port Reset */
   7 static int my3126_reset(struct cphy *cphy, int wait)
   8 {
   9         /*
  10          * This can be done through registers.  It is not required since
  11          * a full chip reset is used.
  12          */
  13         return 0;
  14 }
  15
  16 static int my3126_interrupt_enable(struct cphy *cphy)
  17 {
  18         schedule_delayed_work(&cphy->phy_update, HZ/30);
  19         t1_tpi_read(cphy->adapter, A_ELMER0_GPO, &cphy->elmer_gpo);
  20         return 0;
  21 }
  22
  23 static int my3126_interrupt_disable(struct cphy *cphy)
  24 {
  25         cancel_rearming_delayed_work(&cphy->phy_update);
  26         return 0;
  27 }
  28
  29 static int my3126_interrupt_clear(struct cphy *cphy)
  30 {
  31         return 0;
  32 }
  33
  34 #define OFFSET(REG_ADDR)    (REG_ADDR << 2)
  35
  36 static int my3126_interrupt_handler(struct cphy *cphy)
  37 {
  38         u32 val;
  39         u16 val16;
  40         u16 status;
  41         u32 act_count;
  42         adapter_t *adapter;
  43         adapter = cphy->adapter;
  44
  45         if (cphy->count == 50) {
  46                 mdio_read(cphy, 0x1, 0x1, &val);
  47                 val16 = (u16) val;
  48                 status = cphy->bmsr ^ val16;
  49
  50                 if (status & BMSR_LSTATUS)
  51                         t1_link_changed(adapter, 0);
  52                 cphy->bmsr = val16;
  53
  54                 /* We have only enabled link change interrupts so it
  55                    must be that
  56                  */
  57                 cphy->count = 0;
  58         }
  59
  60         t1_tpi_write(adapter, OFFSET(SUNI1x10GEXP_REG_MSTAT_CONTROL),
  61                 SUNI1x10GEXP_BITMSK_MSTAT_SNAP);
  62         t1_tpi_read(adapter,
  63                 OFFSET(SUNI1x10GEXP_REG_MSTAT_COUNTER_1_LOW), &act_count);
  64         t1_tpi_read(adapter,
  65                 OFFSET(SUNI1x10GEXP_REG_MSTAT_COUNTER_33_LOW), &val);
  66         act_count += val;
  67
  68         /* Populate elmer_gpo with the register value */
  69         t1_tpi_read(adapter, A_ELMER0_GPO, &val);
  70         cphy->elmer_gpo = val;
  71
  72         if ( (val & (1 << 8)) || (val & (1 << 19)) ||
  73              (cphy->act_count == act_count) || cphy->act_on ) {
  74                 if (is_T2(adapter))
  75                         val |= (1 << 9);
  76                 else if (t1_is_T1B(adapter))
  77                         val |= (1 << 20);
  78                 cphy->act_on = 0;
  79         } else {
  80                 if (is_T2(adapter))
  81                         val &= ~(1 << 9);
  82                 else if (t1_is_T1B(adapter))
  83                         val &= ~(1 << 20);
  84                 cphy->act_on = 1;
  85         }
  86
  87         t1_tpi_write(adapter, A_ELMER0_GPO, val);
  88
  89         cphy->elmer_gpo = val;
  90         cphy->act_count = act_count;
  91         cphy->count++;
  92
  93         return cphy_cause_link_change;
  94 }
  95
  96 static void my3216_poll(struct work_struct *work)
  97 {
  98         struct cphy *cphy = container_of(work, struct cphy, phy_update.work);
  99
 100         my3126_interrupt_handler(cphy);
 101 }
 102
 103 static int my3126_set_loopback(struct cphy *cphy, int on)
 104 {
 105         return 0;
 106 }
 107
 108 /* To check the activity LED */
 109 static int my3126_get_link_status(struct cphy *cphy,
 110                         int *link_ok, int *speed, int *duplex, int *fc)
 111 {
 112         u32 val;
 113         u16 val16;
 114         adapter_t *adapter;
 115
 116         adapter = cphy->adapter;
 117         mdio_read(cphy, 0x1, 0x1, &val);
 118         val16 = (u16) val;
 119
 120         /* Populate elmer_gpo with the register value */
 121         t1_tpi_read(adapter, A_ELMER0_GPO, &val);
 122         cphy->elmer_gpo = val;
 123
 124         *link_ok = (val16 & BMSR_LSTATUS);
 125
 126         if (*link_ok) {
 127                 /* Turn on the LED. */
 128                 if (is_T2(adapter))
 129                          val &= ~(1 << 8);
 130                 else if (t1_is_T1B(adapter))
 131                          val &= ~(1 << 19);
 132         } else {
 133                 /* Turn off the LED. */
 134                 if (is_T2(adapter))
 135                          val |= (1 << 8);
 136                 else if (t1_is_T1B(adapter))
 137                          val |= (1 << 19);
 138         }
 139
 140         t1_tpi_write(adapter, A_ELMER0_GPO, val);
 141         cphy->elmer_gpo = val;
 142         *speed = SPEED_10000;
 143         *duplex = DUPLEX_FULL;
 144
 145         /* need to add flow control */
 146         if (fc)
 147                 *fc = PAUSE_RX | PAUSE_TX;
 148
 149         return 0;
 150 }
 151
 152 static void my3126_destroy(struct cphy *cphy)
 153 {
 154         kfree(cphy);
 155 }
 156
 157 static struct cphy_ops my3126_ops = {
 158         .destroy                = my3126_destroy,
 159         .reset                  = my3126_reset,
 160         .interrupt_enable       = my3126_interrupt_enable,
 161         .interrupt_disable      = my3126_interrupt_disable,
 162         .interrupt_clear        = my3126_interrupt_clear,
 163         .interrupt_handler      = my3126_interrupt_handler,
 164         .get_link_status        = my3126_get_link_status,
 165         .set_loopback           = my3126_set_loopback,
 166 };
 167
 168 static struct cphy *my3126_phy_create(adapter_t *adapter,
 169                         int phy_addr, const struct mdio_ops *mdio_ops)
 170 {
 171         struct cphy *cphy = kzalloc(sizeof (*cphy), GFP_KERNEL);
 172
 173         if (!cphy)
 174                 return NULL;
 175
 176         cphy_init(cphy, adapter, phy_addr, &my3126_ops, mdio_ops);
 177         INIT_DELAYED_WORK(&cphy->phy_update, my3216_poll);
 178         cphy->bmsr = 0;
 179
 180         return cphy;
 181 }
 182
 183 /* Chip Reset */
 184 static int my3126_phy_reset(adapter_t * adapter)
 185 {
 186         u32 val;
 187
 188         t1_tpi_read(adapter, A_ELMER0_GPO, &val);
 189         val &= ~4;
 190         t1_tpi_write(adapter, A_ELMER0_GPO, val);
 191         msleep(100);
 192
 193         t1_tpi_write(adapter, A_ELMER0_GPO, val | 4);
 194         msleep(1000);
 195
 196         /* Now lets enable the Laser. Delay 100us */
 197         t1_tpi_read(adapter, A_ELMER0_GPO, &val);
 198         val |= 0x8000;
 199         t1_tpi_write(adapter, A_ELMER0_GPO, val);
 200         udelay(100);
 201         return 0;
 202 }
 203
 204 const struct gphy t1_my3126_ops = {
 205         .create = my3126_phy_create,
 206         .reset = my3126_phy_reset
 207 };