Merge branch 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6
[linux-2.6] / drivers / usb / gadget / atmel_usba_udc.c
1 /*
2  * Driver for the Atmel USBA high speed USB device controller
3  *
4  * Copyright (C) 2005-2007 Atmel Corporation
5  *
6  * This program is free software; you can redistribute it and/or modify
7  * it under the terms of the GNU General Public License version 2 as
8  * published by the Free Software Foundation.
9  */
10 #include <linux/clk.h>
11 #include <linux/module.h>
12 #include <linux/init.h>
13 #include <linux/interrupt.h>
14 #include <linux/io.h>
15 #include <linux/device.h>
16 #include <linux/dma-mapping.h>
17 #include <linux/list.h>
18 #include <linux/platform_device.h>
19 #include <linux/usb/ch9.h>
20 #include <linux/usb/gadget.h>
21 #include <linux/usb/atmel_usba_udc.h>
22 #include <linux/delay.h>
23
24 #include <asm/gpio.h>
25 #include <asm/arch/board.h>
26
27 #include "atmel_usba_udc.h"
28
29
30 static struct usba_udc the_udc;
31 static struct usba_ep *usba_ep;
32
33 #ifdef CONFIG_USB_GADGET_DEBUG_FS
34 #include <linux/debugfs.h>
35 #include <linux/uaccess.h>
36
37 static int queue_dbg_open(struct inode *inode, struct file *file)
38 {
39         struct usba_ep *ep = inode->i_private;
40         struct usba_request *req, *req_copy;
41         struct list_head *queue_data;
42
43         queue_data = kmalloc(sizeof(*queue_data), GFP_KERNEL);
44         if (!queue_data)
45                 return -ENOMEM;
46         INIT_LIST_HEAD(queue_data);
47
48         spin_lock_irq(&ep->udc->lock);
49         list_for_each_entry(req, &ep->queue, queue) {
50                 req_copy = kmalloc(sizeof(*req_copy), GFP_ATOMIC);
51                 if (!req_copy)
52                         goto fail;
53                 memcpy(req_copy, req, sizeof(*req_copy));
54                 list_add_tail(&req_copy->queue, queue_data);
55         }
56         spin_unlock_irq(&ep->udc->lock);
57
58         file->private_data = queue_data;
59         return 0;
60
61 fail:
62         spin_unlock_irq(&ep->udc->lock);
63         list_for_each_entry_safe(req, req_copy, queue_data, queue) {
64                 list_del(&req->queue);
65                 kfree(req);
66         }
67         kfree(queue_data);
68         return -ENOMEM;
69 }
70
71 /*
72  * bbbbbbbb llllllll IZS sssss nnnn FDL\n\0
73  *
74  * b: buffer address
75  * l: buffer length
76  * I/i: interrupt/no interrupt
77  * Z/z: zero/no zero
78  * S/s: short ok/short not ok
79  * s: status
80  * n: nr_packets
81  * F/f: submitted/not submitted to FIFO
82  * D/d: using/not using DMA
83  * L/l: last transaction/not last transaction
84  */
85 static ssize_t queue_dbg_read(struct file *file, char __user *buf,
86                 size_t nbytes, loff_t *ppos)
87 {
88         struct list_head *queue = file->private_data;
89         struct usba_request *req, *tmp_req;
90         size_t len, remaining, actual = 0;
91         char tmpbuf[38];
92
93         if (!access_ok(VERIFY_WRITE, buf, nbytes))
94                 return -EFAULT;
95
96         mutex_lock(&file->f_dentry->d_inode->i_mutex);
97         list_for_each_entry_safe(req, tmp_req, queue, queue) {
98                 len = snprintf(tmpbuf, sizeof(tmpbuf),
99                                 "%8p %08x %c%c%c %5d %c%c%c\n",
100                                 req->req.buf, req->req.length,
101                                 req->req.no_interrupt ? 'i' : 'I',
102                                 req->req.zero ? 'Z' : 'z',
103                                 req->req.short_not_ok ? 's' : 'S',
104                                 req->req.status,
105                                 req->submitted ? 'F' : 'f',
106                                 req->using_dma ? 'D' : 'd',
107                                 req->last_transaction ? 'L' : 'l');
108                 len = min(len, sizeof(tmpbuf));
109                 if (len > nbytes)
110                         break;
111
112                 list_del(&req->queue);
113                 kfree(req);
114
115                 remaining = __copy_to_user(buf, tmpbuf, len);
116                 actual += len - remaining;
117                 if (remaining)
118                         break;
119
120                 nbytes -= len;
121                 buf += len;
122         }
123         mutex_unlock(&file->f_dentry->d_inode->i_mutex);
124
125         return actual;
126 }
127
128 static int queue_dbg_release(struct inode *inode, struct file *file)
129 {
130         struct list_head *queue_data = file->private_data;
131         struct usba_request *req, *tmp_req;
132
133         list_for_each_entry_safe(req, tmp_req, queue_data, queue) {
134                 list_del(&req->queue);
135                 kfree(req);
136         }
137         kfree(queue_data);
138         return 0;
139 }
140
141 static int regs_dbg_open(struct inode *inode, struct file *file)
142 {
143         struct usba_udc *udc;
144         unsigned int i;
145         u32 *data;
146         int ret = -ENOMEM;
147
148         mutex_lock(&inode->i_mutex);
149         udc = inode->i_private;
150         data = kmalloc(inode->i_size, GFP_KERNEL);
151         if (!data)
152                 goto out;
153
154         spin_lock_irq(&udc->lock);
155         for (i = 0; i < inode->i_size / 4; i++)
156                 data[i] = __raw_readl(udc->regs + i * 4);
157         spin_unlock_irq(&udc->lock);
158
159         file->private_data = data;
160         ret = 0;
161
162 out:
163         mutex_unlock(&inode->i_mutex);
164
165         return ret;
166 }
167
168 static ssize_t regs_dbg_read(struct file *file, char __user *buf,
169                 size_t nbytes, loff_t *ppos)
170 {
171         struct inode *inode = file->f_dentry->d_inode;
172         int ret;
173
174         mutex_lock(&inode->i_mutex);
175         ret = simple_read_from_buffer(buf, nbytes, ppos,
176                         file->private_data,
177                         file->f_dentry->d_inode->i_size);
178         mutex_unlock(&inode->i_mutex);
179
180         return ret;
181 }
182
183 static int regs_dbg_release(struct inode *inode, struct file *file)
184 {
185         kfree(file->private_data);
186         return 0;
187 }
188
189 const struct file_operations queue_dbg_fops = {
190         .owner          = THIS_MODULE,
191         .open           = queue_dbg_open,
192         .llseek         = no_llseek,
193         .read           = queue_dbg_read,
194         .release        = queue_dbg_release,
195 };
196
197 const struct file_operations regs_dbg_fops = {
198         .owner          = THIS_MODULE,
199         .open           = regs_dbg_open,
200         .llseek         = generic_file_llseek,
201         .read           = regs_dbg_read,
202         .release        = regs_dbg_release,
203 };
204
205 static void usba_ep_init_debugfs(struct usba_udc *udc,
206                 struct usba_ep *ep)
207 {
208         struct dentry *ep_root;
209
210         ep_root = debugfs_create_dir(ep->ep.name, udc->debugfs_root);
211         if (!ep_root)
212                 goto err_root;
213         ep->debugfs_dir = ep_root;
214
215         ep->debugfs_queue = debugfs_create_file("queue", 0400, ep_root,
216                                                 ep, &queue_dbg_fops);
217         if (!ep->debugfs_queue)
218                 goto err_queue;
219
220         if (ep->can_dma) {
221                 ep->debugfs_dma_status
222                         = debugfs_create_u32("dma_status", 0400, ep_root,
223                                         &ep->last_dma_status);
224                 if (!ep->debugfs_dma_status)
225                         goto err_dma_status;
226         }
227         if (ep_is_control(ep)) {
228                 ep->debugfs_state
229                         = debugfs_create_u32("state", 0400, ep_root,
230                                         &ep->state);
231                 if (!ep->debugfs_state)
232                         goto err_state;
233         }
234
235         return;
236
237 err_state:
238         if (ep->can_dma)
239                 debugfs_remove(ep->debugfs_dma_status);
240 err_dma_status:
241         debugfs_remove(ep->debugfs_queue);
242 err_queue:
243         debugfs_remove(ep_root);
244 err_root:
245         dev_err(&ep->udc->pdev->dev,
246                 "failed to create debugfs directory for %s\n", ep->ep.name);
247 }
248
249 static void usba_ep_cleanup_debugfs(struct usba_ep *ep)
250 {
251         debugfs_remove(ep->debugfs_queue);
252         debugfs_remove(ep->debugfs_dma_status);
253         debugfs_remove(ep->debugfs_state);
254         debugfs_remove(ep->debugfs_dir);
255         ep->debugfs_dma_status = NULL;
256         ep->debugfs_dir = NULL;
257 }
258
259 static void usba_init_debugfs(struct usba_udc *udc)
260 {
261         struct dentry *root, *regs;
262         struct resource *regs_resource;
263
264         root = debugfs_create_dir(udc->gadget.name, NULL);
265         if (IS_ERR(root) || !root)
266                 goto err_root;
267         udc->debugfs_root = root;
268
269         regs = debugfs_create_file("regs", 0400, root, udc, &regs_dbg_fops);
270         if (!regs)
271                 goto err_regs;
272
273         regs_resource = platform_get_resource(udc->pdev, IORESOURCE_MEM,
274                                 CTRL_IOMEM_ID);
275         regs->d_inode->i_size = regs_resource->end - regs_resource->start + 1;
276         udc->debugfs_regs = regs;
277
278         usba_ep_init_debugfs(udc, to_usba_ep(udc->gadget.ep0));
279
280         return;
281
282 err_regs:
283         debugfs_remove(root);
284 err_root:
285         udc->debugfs_root = NULL;
286         dev_err(&udc->pdev->dev, "debugfs is not available\n");
287 }
288
289 static void usba_cleanup_debugfs(struct usba_udc *udc)
290 {
291         usba_ep_cleanup_debugfs(to_usba_ep(udc->gadget.ep0));
292         debugfs_remove(udc->debugfs_regs);
293         debugfs_remove(udc->debugfs_root);
294         udc->debugfs_regs = NULL;
295         udc->debugfs_root = NULL;
296 }
297 #else
298 static inline void usba_ep_init_debugfs(struct usba_udc *udc,
299                                          struct usba_ep *ep)
300 {
301
302 }
303
304 static inline void usba_ep_cleanup_debugfs(struct usba_ep *ep)
305 {
306
307 }
308
309 static inline void usba_init_debugfs(struct usba_udc *udc)
310 {
311
312 }
313
314 static inline void usba_cleanup_debugfs(struct usba_udc *udc)
315 {
316
317 }
318 #endif
319
320 static int vbus_is_present(struct usba_udc *udc)
321 {
322         if (udc->vbus_pin != -1)
323                 return gpio_get_value(udc->vbus_pin);
324
325         /* No Vbus detection: Assume always present */
326         return 1;
327 }
328
329 #if defined(CONFIG_AVR32)
330
331 static void toggle_bias(int is_on)
332 {
333 }
334
335 #elif defined(CONFIG_ARCH_AT91)
336
337 #include <asm/arch/at91_pmc.h>
338
339 static void toggle_bias(int is_on)
340 {
341         unsigned int uckr = at91_sys_read(AT91_CKGR_UCKR);
342
343         if (is_on)
344                 at91_sys_write(AT91_CKGR_UCKR, uckr | AT91_PMC_BIASEN);
345         else
346                 at91_sys_write(AT91_CKGR_UCKR, uckr & ~(AT91_PMC_BIASEN));
347 }
348
349 #endif /* CONFIG_ARCH_AT91 */
350
351 static void next_fifo_transaction(struct usba_ep *ep, struct usba_request *req)
352 {
353         unsigned int transaction_len;
354
355         transaction_len = req->req.length - req->req.actual;
356         req->last_transaction = 1;
357         if (transaction_len > ep->ep.maxpacket) {
358                 transaction_len = ep->ep.maxpacket;
359                 req->last_transaction = 0;
360         } else if (transaction_len == ep->ep.maxpacket && req->req.zero)
361                 req->last_transaction = 0;
362
363         DBG(DBG_QUEUE, "%s: submit_transaction, req %p (length %d)%s\n",
364                 ep->ep.name, req, transaction_len,
365                 req->last_transaction ? ", done" : "");
366
367         memcpy_toio(ep->fifo, req->req.buf + req->req.actual, transaction_len);
368         usba_ep_writel(ep, SET_STA, USBA_TX_PK_RDY);
369         req->req.actual += transaction_len;
370 }
371
372 static void submit_request(struct usba_ep *ep, struct usba_request *req)
373 {
374         DBG(DBG_QUEUE, "%s: submit_request: req %p (length %d)\n",
375                 ep->ep.name, req, req->req.length);
376
377         req->req.actual = 0;
378         req->submitted = 1;
379
380         if (req->using_dma) {
381                 if (req->req.length == 0) {
382                         usba_ep_writel(ep, CTL_ENB, USBA_TX_PK_RDY);
383                         return;
384                 }
385
386                 if (req->req.zero)
387                         usba_ep_writel(ep, CTL_ENB, USBA_SHORT_PACKET);
388                 else
389                         usba_ep_writel(ep, CTL_DIS, USBA_SHORT_PACKET);
390
391                 usba_dma_writel(ep, ADDRESS, req->req.dma);
392                 usba_dma_writel(ep, CONTROL, req->ctrl);
393         } else {
394                 next_fifo_transaction(ep, req);
395                 if (req->last_transaction) {
396                         usba_ep_writel(ep, CTL_DIS, USBA_TX_PK_RDY);
397                         usba_ep_writel(ep, CTL_ENB, USBA_TX_COMPLETE);
398                 } else {
399                         usba_ep_writel(ep, CTL_DIS, USBA_TX_COMPLETE);
400                         usba_ep_writel(ep, CTL_ENB, USBA_TX_PK_RDY);
401                 }
402         }
403 }
404
405 static void submit_next_request(struct usba_ep *ep)
406 {
407         struct usba_request *req;
408
409         if (list_empty(&ep->queue)) {
410                 usba_ep_writel(ep, CTL_DIS, USBA_TX_PK_RDY | USBA_RX_BK_RDY);
411                 return;
412         }
413
414         req = list_entry(ep->queue.next, struct usba_request, queue);
415         if (!req->submitted)
416                 submit_request(ep, req);
417 }
418
419 static void send_status(struct usba_udc *udc, struct usba_ep *ep)
420 {
421         ep->state = STATUS_STAGE_IN;
422         usba_ep_writel(ep, SET_STA, USBA_TX_PK_RDY);
423         usba_ep_writel(ep, CTL_ENB, USBA_TX_COMPLETE);
424 }
425
426 static void receive_data(struct usba_ep *ep)
427 {
428         struct usba_udc *udc = ep->udc;
429         struct usba_request *req;
430         unsigned long status;
431         unsigned int bytecount, nr_busy;
432         int is_complete = 0;
433
434         status = usba_ep_readl(ep, STA);
435         nr_busy = USBA_BFEXT(BUSY_BANKS, status);
436
437         DBG(DBG_QUEUE, "receive data: nr_busy=%u\n", nr_busy);
438
439         while (nr_busy > 0) {
440                 if (list_empty(&ep->queue)) {
441                         usba_ep_writel(ep, CTL_DIS, USBA_RX_BK_RDY);
442                         break;
443                 }
444                 req = list_entry(ep->queue.next,
445                                  struct usba_request, queue);
446
447                 bytecount = USBA_BFEXT(BYTE_COUNT, status);
448
449                 if (status & (1 << 31))
450                         is_complete = 1;
451                 if (req->req.actual + bytecount >= req->req.length) {
452                         is_complete = 1;
453                         bytecount = req->req.length - req->req.actual;
454                 }
455
456                 memcpy_fromio(req->req.buf + req->req.actual,
457                                 ep->fifo, bytecount);
458                 req->req.actual += bytecount;
459
460                 usba_ep_writel(ep, CLR_STA, USBA_RX_BK_RDY);
461
462                 if (is_complete) {
463                         DBG(DBG_QUEUE, "%s: request done\n", ep->ep.name);
464                         req->req.status = 0;
465                         list_del_init(&req->queue);
466                         usba_ep_writel(ep, CTL_DIS, USBA_RX_BK_RDY);
467                         spin_unlock(&udc->lock);
468                         req->req.complete(&ep->ep, &req->req);
469                         spin_lock(&udc->lock);
470                 }
471
472                 status = usba_ep_readl(ep, STA);
473                 nr_busy = USBA_BFEXT(BUSY_BANKS, status);
474
475                 if (is_complete && ep_is_control(ep)) {
476                         send_status(udc, ep);
477                         break;
478                 }
479         }
480 }
481
482 static void
483 request_complete(struct usba_ep *ep, struct usba_request *req, int status)
484 {
485         struct usba_udc *udc = ep->udc;
486
487         WARN_ON(!list_empty(&req->queue));
488
489         if (req->req.status == -EINPROGRESS)
490                 req->req.status = status;
491
492         if (req->mapped) {
493                 dma_unmap_single(
494                         &udc->pdev->dev, req->req.dma, req->req.length,
495                         ep->is_in ? DMA_TO_DEVICE : DMA_FROM_DEVICE);
496                 req->req.dma = DMA_ADDR_INVALID;
497                 req->mapped = 0;
498         }
499
500         DBG(DBG_GADGET | DBG_REQ,
501                 "%s: req %p complete: status %d, actual %u\n",
502                 ep->ep.name, req, req->req.status, req->req.actual);
503
504         spin_unlock(&udc->lock);
505         req->req.complete(&ep->ep, &req->req);
506         spin_lock(&udc->lock);
507 }
508
509 static void
510 request_complete_list(struct usba_ep *ep, struct list_head *list, int status)
511 {
512         struct usba_request *req, *tmp_req;
513
514         list_for_each_entry_safe(req, tmp_req, list, queue) {
515                 list_del_init(&req->queue);
516                 request_complete(ep, req, status);
517         }
518 }
519
520 static int
521 usba_ep_enable(struct usb_ep *_ep, const struct usb_endpoint_descriptor *desc)
522 {
523         struct usba_ep *ep = to_usba_ep(_ep);
524         struct usba_udc *udc = ep->udc;
525         unsigned long flags, ept_cfg, maxpacket;
526         unsigned int nr_trans;
527
528         DBG(DBG_GADGET, "%s: ep_enable: desc=%p\n", ep->ep.name, desc);
529
530         maxpacket = le16_to_cpu(desc->wMaxPacketSize) & 0x7ff;
531
532         if (((desc->bEndpointAddress & USB_ENDPOINT_NUMBER_MASK) != ep->index)
533                         || ep->index == 0
534                         || desc->bDescriptorType != USB_DT_ENDPOINT
535                         || maxpacket == 0
536                         || maxpacket > ep->fifo_size) {
537                 DBG(DBG_ERR, "ep_enable: Invalid argument");
538                 return -EINVAL;
539         }
540
541         ep->is_isoc = 0;
542         ep->is_in = 0;
543
544         if (maxpacket <= 8)
545                 ept_cfg = USBA_BF(EPT_SIZE, USBA_EPT_SIZE_8);
546         else
547                 /* LSB is bit 1, not 0 */
548                 ept_cfg = USBA_BF(EPT_SIZE, fls(maxpacket - 1) - 3);
549
550         DBG(DBG_HW, "%s: EPT_SIZE = %lu (maxpacket = %lu)\n",
551                         ep->ep.name, ept_cfg, maxpacket);
552
553         if ((desc->bEndpointAddress & USB_ENDPOINT_DIR_MASK) == USB_DIR_IN) {
554                 ep->is_in = 1;
555                 ept_cfg |= USBA_EPT_DIR_IN;
556         }
557
558         switch (desc->bmAttributes & USB_ENDPOINT_XFERTYPE_MASK) {
559         case USB_ENDPOINT_XFER_CONTROL:
560                 ept_cfg |= USBA_BF(EPT_TYPE, USBA_EPT_TYPE_CONTROL);
561                 ept_cfg |= USBA_BF(BK_NUMBER, USBA_BK_NUMBER_ONE);
562                 break;
563         case USB_ENDPOINT_XFER_ISOC:
564                 if (!ep->can_isoc) {
565                         DBG(DBG_ERR, "ep_enable: %s is not isoc capable\n",
566                                         ep->ep.name);
567                         return -EINVAL;
568                 }
569
570                 /*
571                  * Bits 11:12 specify number of _additional_
572                  * transactions per microframe.
573                  */
574                 nr_trans = ((le16_to_cpu(desc->wMaxPacketSize) >> 11) & 3) + 1;
575                 if (nr_trans > 3)
576                         return -EINVAL;
577
578                 ep->is_isoc = 1;
579                 ept_cfg |= USBA_BF(EPT_TYPE, USBA_EPT_TYPE_ISO);
580
581                 /*
582                  * Do triple-buffering on high-bandwidth iso endpoints.
583                  */
584                 if (nr_trans > 1 && ep->nr_banks == 3)
585                         ept_cfg |= USBA_BF(BK_NUMBER, USBA_BK_NUMBER_TRIPLE);
586                 else
587                         ept_cfg |= USBA_BF(BK_NUMBER, USBA_BK_NUMBER_DOUBLE);
588                 ept_cfg |= USBA_BF(NB_TRANS, nr_trans);
589                 break;
590         case USB_ENDPOINT_XFER_BULK:
591                 ept_cfg |= USBA_BF(EPT_TYPE, USBA_EPT_TYPE_BULK);
592                 ept_cfg |= USBA_BF(BK_NUMBER, USBA_BK_NUMBER_DOUBLE);
593                 break;
594         case USB_ENDPOINT_XFER_INT:
595                 ept_cfg |= USBA_BF(EPT_TYPE, USBA_EPT_TYPE_INT);
596                 ept_cfg |= USBA_BF(BK_NUMBER, USBA_BK_NUMBER_DOUBLE);
597                 break;
598         }
599
600         spin_lock_irqsave(&ep->udc->lock, flags);
601
602         if (ep->desc) {
603                 spin_unlock_irqrestore(&ep->udc->lock, flags);
604                 DBG(DBG_ERR, "ep%d already enabled\n", ep->index);
605                 return -EBUSY;
606         }
607
608         ep->desc = desc;
609         ep->ep.maxpacket = maxpacket;
610
611         usba_ep_writel(ep, CFG, ept_cfg);
612         usba_ep_writel(ep, CTL_ENB, USBA_EPT_ENABLE);
613
614         if (ep->can_dma) {
615                 u32 ctrl;
616
617                 usba_writel(udc, INT_ENB,
618                                 (usba_readl(udc, INT_ENB)
619                                         | USBA_BF(EPT_INT, 1 << ep->index)
620                                         | USBA_BF(DMA_INT, 1 << ep->index)));
621                 ctrl = USBA_AUTO_VALID | USBA_INTDIS_DMA;
622                 usba_ep_writel(ep, CTL_ENB, ctrl);
623         } else {
624                 usba_writel(udc, INT_ENB,
625                                 (usba_readl(udc, INT_ENB)
626                                         | USBA_BF(EPT_INT, 1 << ep->index)));
627         }
628
629         spin_unlock_irqrestore(&udc->lock, flags);
630
631         DBG(DBG_HW, "EPT_CFG%d after init: %#08lx\n", ep->index,
632                         (unsigned long)usba_ep_readl(ep, CFG));
633         DBG(DBG_HW, "INT_ENB after init: %#08lx\n",
634                         (unsigned long)usba_readl(udc, INT_ENB));
635
636         return 0;
637 }
638
639 static int usba_ep_disable(struct usb_ep *_ep)
640 {
641         struct usba_ep *ep = to_usba_ep(_ep);
642         struct usba_udc *udc = ep->udc;
643         LIST_HEAD(req_list);
644         unsigned long flags;
645
646         DBG(DBG_GADGET, "ep_disable: %s\n", ep->ep.name);
647
648         spin_lock_irqsave(&udc->lock, flags);
649
650         if (!ep->desc) {
651                 spin_unlock_irqrestore(&udc->lock, flags);
652                 DBG(DBG_ERR, "ep_disable: %s not enabled\n", ep->ep.name);
653                 return -EINVAL;
654         }
655         ep->desc = NULL;
656
657         list_splice_init(&ep->queue, &req_list);
658         if (ep->can_dma) {
659                 usba_dma_writel(ep, CONTROL, 0);
660                 usba_dma_writel(ep, ADDRESS, 0);
661                 usba_dma_readl(ep, STATUS);
662         }
663         usba_ep_writel(ep, CTL_DIS, USBA_EPT_ENABLE);
664         usba_writel(udc, INT_ENB,
665                         usba_readl(udc, INT_ENB)
666                         & ~USBA_BF(EPT_INT, 1 << ep->index));
667
668         request_complete_list(ep, &req_list, -ESHUTDOWN);
669
670         spin_unlock_irqrestore(&udc->lock, flags);
671
672         return 0;
673 }
674
675 static struct usb_request *
676 usba_ep_alloc_request(struct usb_ep *_ep, gfp_t gfp_flags)
677 {
678         struct usba_request *req;
679
680         DBG(DBG_GADGET, "ep_alloc_request: %p, 0x%x\n", _ep, gfp_flags);
681
682         req = kzalloc(sizeof(*req), gfp_flags);
683         if (!req)
684                 return NULL;
685
686         INIT_LIST_HEAD(&req->queue);
687         req->req.dma = DMA_ADDR_INVALID;
688
689         return &req->req;
690 }
691
692 static void
693 usba_ep_free_request(struct usb_ep *_ep, struct usb_request *_req)
694 {
695         struct usba_request *req = to_usba_req(_req);
696
697         DBG(DBG_GADGET, "ep_free_request: %p, %p\n", _ep, _req);
698
699         kfree(req);
700 }
701
702 static int queue_dma(struct usba_udc *udc, struct usba_ep *ep,
703                 struct usba_request *req, gfp_t gfp_flags)
704 {
705         unsigned long flags;
706         int ret;
707
708         DBG(DBG_DMA, "%s: req l/%u d/%08x %c%c%c\n",
709                 ep->ep.name, req->req.length, req->req.dma,
710                 req->req.zero ? 'Z' : 'z',
711                 req->req.short_not_ok ? 'S' : 's',
712                 req->req.no_interrupt ? 'I' : 'i');
713
714         if (req->req.length > 0x10000) {
715                 /* Lengths from 0 to 65536 (inclusive) are supported */
716                 DBG(DBG_ERR, "invalid request length %u\n", req->req.length);
717                 return -EINVAL;
718         }
719
720         req->using_dma = 1;
721
722         if (req->req.dma == DMA_ADDR_INVALID) {
723                 req->req.dma = dma_map_single(
724                         &udc->pdev->dev, req->req.buf, req->req.length,
725                         ep->is_in ? DMA_TO_DEVICE : DMA_FROM_DEVICE);
726                 req->mapped = 1;
727         } else {
728                 dma_sync_single_for_device(
729                         &udc->pdev->dev, req->req.dma, req->req.length,
730                         ep->is_in ? DMA_TO_DEVICE : DMA_FROM_DEVICE);
731                 req->mapped = 0;
732         }
733
734         req->ctrl = USBA_BF(DMA_BUF_LEN, req->req.length)
735                         | USBA_DMA_CH_EN | USBA_DMA_END_BUF_IE
736                         | USBA_DMA_END_TR_EN | USBA_DMA_END_TR_IE;
737
738         if (ep->is_in)
739                 req->ctrl |= USBA_DMA_END_BUF_EN;
740
741         /*
742          * Add this request to the queue and submit for DMA if
743          * possible. Check if we're still alive first -- we may have
744          * received a reset since last time we checked.
745          */
746         ret = -ESHUTDOWN;
747         spin_lock_irqsave(&udc->lock, flags);
748         if (ep->desc) {
749                 if (list_empty(&ep->queue))
750                         submit_request(ep, req);
751
752                 list_add_tail(&req->queue, &ep->queue);
753                 ret = 0;
754         }
755         spin_unlock_irqrestore(&udc->lock, flags);
756
757         return ret;
758 }
759
760 static int
761 usba_ep_queue(struct usb_ep *_ep, struct usb_request *_req, gfp_t gfp_flags)
762 {
763         struct usba_request *req = to_usba_req(_req);
764         struct usba_ep *ep = to_usba_ep(_ep);
765         struct usba_udc *udc = ep->udc;
766         unsigned long flags;
767         int ret;
768
769         DBG(DBG_GADGET | DBG_QUEUE | DBG_REQ, "%s: queue req %p, len %u\n",
770                         ep->ep.name, req, _req->length);
771
772         if (!udc->driver || udc->gadget.speed == USB_SPEED_UNKNOWN || !ep->desc)
773                 return -ESHUTDOWN;
774
775         req->submitted = 0;
776         req->using_dma = 0;
777         req->last_transaction = 0;
778
779         _req->status = -EINPROGRESS;
780         _req->actual = 0;
781
782         if (ep->can_dma)
783                 return queue_dma(udc, ep, req, gfp_flags);
784
785         /* May have received a reset since last time we checked */
786         ret = -ESHUTDOWN;
787         spin_lock_irqsave(&udc->lock, flags);
788         if (ep->desc) {
789                 list_add_tail(&req->queue, &ep->queue);
790
791                 if (ep->is_in || (ep_is_control(ep)
792                                 && (ep->state == DATA_STAGE_IN
793                                         || ep->state == STATUS_STAGE_IN)))
794                         usba_ep_writel(ep, CTL_ENB, USBA_TX_PK_RDY);
795                 else
796                         usba_ep_writel(ep, CTL_ENB, USBA_RX_BK_RDY);
797                 ret = 0;
798         }
799         spin_unlock_irqrestore(&udc->lock, flags);
800
801         return ret;
802 }
803
804 static void
805 usba_update_req(struct usba_ep *ep, struct usba_request *req, u32 status)
806 {
807         req->req.actual = req->req.length - USBA_BFEXT(DMA_BUF_LEN, status);
808 }
809
810 static int stop_dma(struct usba_ep *ep, u32 *pstatus)
811 {
812         unsigned int timeout;
813         u32 status;
814
815         /*
816          * Stop the DMA controller. When writing both CH_EN
817          * and LINK to 0, the other bits are not affected.
818          */
819         usba_dma_writel(ep, CONTROL, 0);
820
821         /* Wait for the FIFO to empty */
822         for (timeout = 40; timeout; --timeout) {
823                 status = usba_dma_readl(ep, STATUS);
824                 if (!(status & USBA_DMA_CH_EN))
825                         break;
826                 udelay(1);
827         }
828
829         if (pstatus)
830                 *pstatus = status;
831
832         if (timeout == 0) {
833                 dev_err(&ep->udc->pdev->dev,
834                         "%s: timed out waiting for DMA FIFO to empty\n",
835                         ep->ep.name);
836                 return -ETIMEDOUT;
837         }
838
839         return 0;
840 }
841
842 static int usba_ep_dequeue(struct usb_ep *_ep, struct usb_request *_req)
843 {
844         struct usba_ep *ep = to_usba_ep(_ep);
845         struct usba_udc *udc = ep->udc;
846         struct usba_request *req = to_usba_req(_req);
847         unsigned long flags;
848         u32 status;
849
850         DBG(DBG_GADGET | DBG_QUEUE, "ep_dequeue: %s, req %p\n",
851                         ep->ep.name, req);
852
853         spin_lock_irqsave(&udc->lock, flags);
854
855         if (req->using_dma) {
856                 /*
857                  * If this request is currently being transferred,
858                  * stop the DMA controller and reset the FIFO.
859                  */
860                 if (ep->queue.next == &req->queue) {
861                         status = usba_dma_readl(ep, STATUS);
862                         if (status & USBA_DMA_CH_EN)
863                                 stop_dma(ep, &status);
864
865 #ifdef CONFIG_USB_GADGET_DEBUG_FS
866                         ep->last_dma_status = status;
867 #endif
868
869                         usba_writel(udc, EPT_RST, 1 << ep->index);
870
871                         usba_update_req(ep, req, status);
872                 }
873         }
874
875         /*
876          * Errors should stop the queue from advancing until the
877          * completion function returns.
878          */
879         list_del_init(&req->queue);
880
881         request_complete(ep, req, -ECONNRESET);
882
883         /* Process the next request if any */
884         submit_next_request(ep);
885         spin_unlock_irqrestore(&udc->lock, flags);
886
887         return 0;
888 }
889
890 static int usba_ep_set_halt(struct usb_ep *_ep, int value)
891 {
892         struct usba_ep *ep = to_usba_ep(_ep);
893         struct usba_udc *udc = ep->udc;
894         unsigned long flags;
895         int ret = 0;
896
897         DBG(DBG_GADGET, "endpoint %s: %s HALT\n", ep->ep.name,
898                         value ? "set" : "clear");
899
900         if (!ep->desc) {
901                 DBG(DBG_ERR, "Attempted to halt uninitialized ep %s\n",
902                                 ep->ep.name);
903                 return -ENODEV;
904         }
905         if (ep->is_isoc) {
906                 DBG(DBG_ERR, "Attempted to halt isochronous ep %s\n",
907                                 ep->ep.name);
908                 return -ENOTTY;
909         }
910
911         spin_lock_irqsave(&udc->lock, flags);
912
913         /*
914          * We can't halt IN endpoints while there are still data to be
915          * transferred
916          */
917         if (!list_empty(&ep->queue)
918                         || ((value && ep->is_in && (usba_ep_readl(ep, STA)
919                                         & USBA_BF(BUSY_BANKS, -1L))))) {
920                 ret = -EAGAIN;
921         } else {
922                 if (value)
923                         usba_ep_writel(ep, SET_STA, USBA_FORCE_STALL);
924                 else
925                         usba_ep_writel(ep, CLR_STA,
926                                         USBA_FORCE_STALL | USBA_TOGGLE_CLR);
927                 usba_ep_readl(ep, STA);
928         }
929
930         spin_unlock_irqrestore(&udc->lock, flags);
931
932         return ret;
933 }
934
935 static int usba_ep_fifo_status(struct usb_ep *_ep)
936 {
937         struct usba_ep *ep = to_usba_ep(_ep);
938
939         return USBA_BFEXT(BYTE_COUNT, usba_ep_readl(ep, STA));
940 }
941
942 static void usba_ep_fifo_flush(struct usb_ep *_ep)
943 {
944         struct usba_ep *ep = to_usba_ep(_ep);
945         struct usba_udc *udc = ep->udc;
946
947         usba_writel(udc, EPT_RST, 1 << ep->index);
948 }
949
950 static const struct usb_ep_ops usba_ep_ops = {
951         .enable         = usba_ep_enable,
952         .disable        = usba_ep_disable,
953         .alloc_request  = usba_ep_alloc_request,
954         .free_request   = usba_ep_free_request,
955         .queue          = usba_ep_queue,
956         .dequeue        = usba_ep_dequeue,
957         .set_halt       = usba_ep_set_halt,
958         .fifo_status    = usba_ep_fifo_status,
959         .fifo_flush     = usba_ep_fifo_flush,
960 };
961
962 static int usba_udc_get_frame(struct usb_gadget *gadget)
963 {
964         struct usba_udc *udc = to_usba_udc(gadget);
965
966         return USBA_BFEXT(FRAME_NUMBER, usba_readl(udc, FNUM));
967 }
968
969 static int usba_udc_wakeup(struct usb_gadget *gadget)
970 {
971         struct usba_udc *udc = to_usba_udc(gadget);
972         unsigned long flags;
973         u32 ctrl;
974         int ret = -EINVAL;
975
976         spin_lock_irqsave(&udc->lock, flags);
977         if (udc->devstatus & (1 << USB_DEVICE_REMOTE_WAKEUP)) {
978                 ctrl = usba_readl(udc, CTRL);
979                 usba_writel(udc, CTRL, ctrl | USBA_REMOTE_WAKE_UP);
980                 ret = 0;
981         }
982         spin_unlock_irqrestore(&udc->lock, flags);
983
984         return ret;
985 }
986
987 static int
988 usba_udc_set_selfpowered(struct usb_gadget *gadget, int is_selfpowered)
989 {
990         struct usba_udc *udc = to_usba_udc(gadget);
991         unsigned long flags;
992
993         spin_lock_irqsave(&udc->lock, flags);
994         if (is_selfpowered)
995                 udc->devstatus |= 1 << USB_DEVICE_SELF_POWERED;
996         else
997                 udc->devstatus &= ~(1 << USB_DEVICE_SELF_POWERED);
998         spin_unlock_irqrestore(&udc->lock, flags);
999
1000         return 0;
1001 }
1002
1003 static const struct usb_gadget_ops usba_udc_ops = {
1004         .get_frame              = usba_udc_get_frame,
1005         .wakeup                 = usba_udc_wakeup,
1006         .set_selfpowered        = usba_udc_set_selfpowered,
1007 };
1008
1009 static struct usb_endpoint_descriptor usba_ep0_desc = {
1010         .bLength = USB_DT_ENDPOINT_SIZE,
1011         .bDescriptorType = USB_DT_ENDPOINT,
1012         .bEndpointAddress = 0,
1013         .bmAttributes = USB_ENDPOINT_XFER_CONTROL,
1014         .wMaxPacketSize = __constant_cpu_to_le16(64),
1015         /* FIXME: I have no idea what to put here */
1016         .bInterval = 1,
1017 };
1018
1019 static void nop_release(struct device *dev)
1020 {
1021
1022 }
1023
1024 static struct usba_udc the_udc = {
1025         .gadget = {
1026                 .ops            = &usba_udc_ops,
1027                 .ep_list        = LIST_HEAD_INIT(the_udc.gadget.ep_list),
1028                 .is_dualspeed   = 1,
1029                 .name           = "atmel_usba_udc",
1030                 .dev    = {
1031                         .bus_id         = "gadget",
1032                         .release        = nop_release,
1033                 },
1034         },
1035
1036         .lock   = SPIN_LOCK_UNLOCKED,
1037 };
1038
1039 /*
1040  * Called with interrupts disabled and udc->lock held.
1041  */
1042 static void reset_all_endpoints(struct usba_udc *udc)
1043 {
1044         struct usba_ep *ep;
1045         struct usba_request *req, *tmp_req;
1046
1047         usba_writel(udc, EPT_RST, ~0UL);
1048
1049         ep = to_usba_ep(udc->gadget.ep0);
1050         list_for_each_entry_safe(req, tmp_req, &ep->queue, queue) {
1051                 list_del_init(&req->queue);
1052                 request_complete(ep, req, -ECONNRESET);
1053         }
1054
1055         list_for_each_entry(ep, &udc->gadget.ep_list, ep.ep_list) {
1056                 if (ep->desc) {
1057                         spin_unlock(&udc->lock);
1058                         usba_ep_disable(&ep->ep);
1059                         spin_lock(&udc->lock);
1060                 }
1061         }
1062 }
1063
1064 static struct usba_ep *get_ep_by_addr(struct usba_udc *udc, u16 wIndex)
1065 {
1066         struct usba_ep *ep;
1067
1068         if ((wIndex & USB_ENDPOINT_NUMBER_MASK) == 0)
1069                 return to_usba_ep(udc->gadget.ep0);
1070
1071         list_for_each_entry (ep, &udc->gadget.ep_list, ep.ep_list) {
1072                 u8 bEndpointAddress;
1073
1074                 if (!ep->desc)
1075                         continue;
1076                 bEndpointAddress = ep->desc->bEndpointAddress;
1077                 if ((wIndex ^ bEndpointAddress) & USB_DIR_IN)
1078                         continue;
1079                 if ((bEndpointAddress & USB_ENDPOINT_NUMBER_MASK)
1080                                 == (wIndex & USB_ENDPOINT_NUMBER_MASK))
1081                         return ep;
1082         }
1083
1084         return NULL;
1085 }
1086
1087 /* Called with interrupts disabled and udc->lock held */
1088 static inline void set_protocol_stall(struct usba_udc *udc, struct usba_ep *ep)
1089 {
1090         usba_ep_writel(ep, SET_STA, USBA_FORCE_STALL);
1091         ep->state = WAIT_FOR_SETUP;
1092 }
1093
1094 static inline int is_stalled(struct usba_udc *udc, struct usba_ep *ep)
1095 {
1096         if (usba_ep_readl(ep, STA) & USBA_FORCE_STALL)
1097                 return 1;
1098         return 0;
1099 }
1100
1101 static inline void set_address(struct usba_udc *udc, unsigned int addr)
1102 {
1103         u32 regval;
1104
1105         DBG(DBG_BUS, "setting address %u...\n", addr);
1106         regval = usba_readl(udc, CTRL);
1107         regval = USBA_BFINS(DEV_ADDR, addr, regval);
1108         usba_writel(udc, CTRL, regval);
1109 }
1110
1111 static int do_test_mode(struct usba_udc *udc)
1112 {
1113         static const char test_packet_buffer[] = {
1114                 /* JKJKJKJK * 9 */
1115                 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00,
1116                 /* JJKKJJKK * 8 */
1117                 0xAA, 0xAA, 0xAA, 0xAA, 0xAA, 0xAA, 0xAA, 0xAA,
1118                 /* JJKKJJKK * 8 */
1119                 0xEE, 0xEE, 0xEE, 0xEE, 0xEE, 0xEE, 0xEE, 0xEE,
1120                 /* JJJJJJJKKKKKKK * 8 */
1121                 0xFE, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF,
1122                 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF,
1123                 /* JJJJJJJK * 8 */
1124                 0x7F, 0xBF, 0xDF, 0xEF, 0xF7, 0xFB, 0xFD,
1125                 /* {JKKKKKKK * 10}, JK */
1126                 0xFC, 0x7E, 0xBF, 0xDF, 0xEF, 0xF7, 0xFB, 0xFD, 0x7E
1127         };
1128         struct usba_ep *ep;
1129         struct device *dev = &udc->pdev->dev;
1130         int test_mode;
1131
1132         test_mode = udc->test_mode;
1133
1134         /* Start from a clean slate */
1135         reset_all_endpoints(udc);
1136
1137         switch (test_mode) {
1138         case 0x0100:
1139                 /* Test_J */
1140                 usba_writel(udc, TST, USBA_TST_J_MODE);
1141                 dev_info(dev, "Entering Test_J mode...\n");
1142                 break;
1143         case 0x0200:
1144                 /* Test_K */
1145                 usba_writel(udc, TST, USBA_TST_K_MODE);
1146                 dev_info(dev, "Entering Test_K mode...\n");
1147                 break;
1148         case 0x0300:
1149                 /*
1150                  * Test_SE0_NAK: Force high-speed mode and set up ep0
1151                  * for Bulk IN transfers
1152                  */
1153                 ep = &usba_ep[0];
1154                 usba_writel(udc, TST,
1155                                 USBA_BF(SPEED_CFG, USBA_SPEED_CFG_FORCE_HIGH));
1156                 usba_ep_writel(ep, CFG,
1157                                 USBA_BF(EPT_SIZE, USBA_EPT_SIZE_64)
1158                                 | USBA_EPT_DIR_IN
1159                                 | USBA_BF(EPT_TYPE, USBA_EPT_TYPE_BULK)
1160                                 | USBA_BF(BK_NUMBER, 1));
1161                 if (!(usba_ep_readl(ep, CFG) & USBA_EPT_MAPPED)) {
1162                         set_protocol_stall(udc, ep);
1163                         dev_err(dev, "Test_SE0_NAK: ep0 not mapped\n");
1164                 } else {
1165                         usba_ep_writel(ep, CTL_ENB, USBA_EPT_ENABLE);
1166                         dev_info(dev, "Entering Test_SE0_NAK mode...\n");
1167                 }
1168                 break;
1169         case 0x0400:
1170                 /* Test_Packet */
1171                 ep = &usba_ep[0];
1172                 usba_ep_writel(ep, CFG,
1173                                 USBA_BF(EPT_SIZE, USBA_EPT_SIZE_64)
1174                                 | USBA_EPT_DIR_IN
1175                                 | USBA_BF(EPT_TYPE, USBA_EPT_TYPE_BULK)
1176                                 | USBA_BF(BK_NUMBER, 1));
1177                 if (!(usba_ep_readl(ep, CFG) & USBA_EPT_MAPPED)) {
1178                         set_protocol_stall(udc, ep);
1179                         dev_err(dev, "Test_Packet: ep0 not mapped\n");
1180                 } else {
1181                         usba_ep_writel(ep, CTL_ENB, USBA_EPT_ENABLE);
1182                         usba_writel(udc, TST, USBA_TST_PKT_MODE);
1183                         memcpy_toio(ep->fifo, test_packet_buffer,
1184                                         sizeof(test_packet_buffer));
1185                         usba_ep_writel(ep, SET_STA, USBA_TX_PK_RDY);
1186                         dev_info(dev, "Entering Test_Packet mode...\n");
1187                 }
1188                 break;
1189         default:
1190                 dev_err(dev, "Invalid test mode: 0x%04x\n", test_mode);
1191                 return -EINVAL;
1192         }
1193
1194         return 0;
1195 }
1196
1197 /* Avoid overly long expressions */
1198 static inline bool feature_is_dev_remote_wakeup(struct usb_ctrlrequest *crq)
1199 {
1200         if (crq->wValue == __constant_cpu_to_le16(USB_DEVICE_REMOTE_WAKEUP))
1201                 return true;
1202         return false;
1203 }
1204
1205 static inline bool feature_is_dev_test_mode(struct usb_ctrlrequest *crq)
1206 {
1207         if (crq->wValue == __constant_cpu_to_le16(USB_DEVICE_TEST_MODE))
1208                 return true;
1209         return false;
1210 }
1211
1212 static inline bool feature_is_ep_halt(struct usb_ctrlrequest *crq)
1213 {
1214         if (crq->wValue == __constant_cpu_to_le16(USB_ENDPOINT_HALT))
1215                 return true;
1216         return false;
1217 }
1218
1219 static int handle_ep0_setup(struct usba_udc *udc, struct usba_ep *ep,
1220                 struct usb_ctrlrequest *crq)
1221 {
1222         int retval = 0;;
1223
1224         switch (crq->bRequest) {
1225         case USB_REQ_GET_STATUS: {
1226                 u16 status;
1227
1228                 if (crq->bRequestType == (USB_DIR_IN | USB_RECIP_DEVICE)) {
1229                         status = cpu_to_le16(udc->devstatus);
1230                 } else if (crq->bRequestType
1231                                 == (USB_DIR_IN | USB_RECIP_INTERFACE)) {
1232                         status = __constant_cpu_to_le16(0);
1233                 } else if (crq->bRequestType
1234                                 == (USB_DIR_IN | USB_RECIP_ENDPOINT)) {
1235                         struct usba_ep *target;
1236
1237                         target = get_ep_by_addr(udc, le16_to_cpu(crq->wIndex));
1238                         if (!target)
1239                                 goto stall;
1240
1241                         status = 0;
1242                         if (is_stalled(udc, target))
1243                                 status |= __constant_cpu_to_le16(1);
1244                 } else
1245                         goto delegate;
1246
1247                 /* Write directly to the FIFO. No queueing is done. */
1248                 if (crq->wLength != __constant_cpu_to_le16(sizeof(status)))
1249                         goto stall;
1250                 ep->state = DATA_STAGE_IN;
1251                 __raw_writew(status, ep->fifo);
1252                 usba_ep_writel(ep, SET_STA, USBA_TX_PK_RDY);
1253                 break;
1254         }
1255
1256         case USB_REQ_CLEAR_FEATURE: {
1257                 if (crq->bRequestType == USB_RECIP_DEVICE) {
1258                         if (feature_is_dev_remote_wakeup(crq))
1259                                 udc->devstatus
1260                                         &= ~(1 << USB_DEVICE_REMOTE_WAKEUP);
1261                         else
1262                                 /* Can't CLEAR_FEATURE TEST_MODE */
1263                                 goto stall;
1264                 } else if (crq->bRequestType == USB_RECIP_ENDPOINT) {
1265                         struct usba_ep *target;
1266
1267                         if (crq->wLength != __constant_cpu_to_le16(0)
1268                                         || !feature_is_ep_halt(crq))
1269                                 goto stall;
1270                         target = get_ep_by_addr(udc, le16_to_cpu(crq->wIndex));
1271                         if (!target)
1272                                 goto stall;
1273
1274                         usba_ep_writel(target, CLR_STA, USBA_FORCE_STALL);
1275                         if (target->index != 0)
1276                                 usba_ep_writel(target, CLR_STA,
1277                                                 USBA_TOGGLE_CLR);
1278                 } else {
1279                         goto delegate;
1280                 }
1281
1282                 send_status(udc, ep);
1283                 break;
1284         }
1285
1286         case USB_REQ_SET_FEATURE: {
1287                 if (crq->bRequestType == USB_RECIP_DEVICE) {
1288                         if (feature_is_dev_test_mode(crq)) {
1289                                 send_status(udc, ep);
1290                                 ep->state = STATUS_STAGE_TEST;
1291                                 udc->test_mode = le16_to_cpu(crq->wIndex);
1292                                 return 0;
1293                         } else if (feature_is_dev_remote_wakeup(crq)) {
1294                                 udc->devstatus |= 1 << USB_DEVICE_REMOTE_WAKEUP;
1295                         } else {
1296                                 goto stall;
1297                         }
1298                 } else if (crq->bRequestType == USB_RECIP_ENDPOINT) {
1299                         struct usba_ep *target;
1300
1301                         if (crq->wLength != __constant_cpu_to_le16(0)
1302                                         || !feature_is_ep_halt(crq))
1303                                 goto stall;
1304
1305                         target = get_ep_by_addr(udc, le16_to_cpu(crq->wIndex));
1306                         if (!target)
1307                                 goto stall;
1308
1309                         usba_ep_writel(target, SET_STA, USBA_FORCE_STALL);
1310                 } else
1311                         goto delegate;
1312
1313                 send_status(udc, ep);
1314                 break;
1315         }
1316
1317         case USB_REQ_SET_ADDRESS:
1318                 if (crq->bRequestType != (USB_DIR_OUT | USB_RECIP_DEVICE))
1319                         goto delegate;
1320
1321                 set_address(udc, le16_to_cpu(crq->wValue));
1322                 send_status(udc, ep);
1323                 ep->state = STATUS_STAGE_ADDR;
1324                 break;
1325
1326         default:
1327 delegate:
1328                 spin_unlock(&udc->lock);
1329                 retval = udc->driver->setup(&udc->gadget, crq);
1330                 spin_lock(&udc->lock);
1331         }
1332
1333         return retval;
1334
1335 stall:
1336         pr_err("udc: %s: Invalid setup request: %02x.%02x v%04x i%04x l%d, "
1337                 "halting endpoint...\n",
1338                 ep->ep.name, crq->bRequestType, crq->bRequest,
1339                 le16_to_cpu(crq->wValue), le16_to_cpu(crq->wIndex),
1340                 le16_to_cpu(crq->wLength));
1341         set_protocol_stall(udc, ep);
1342         return -1;
1343 }
1344
1345 static void usba_control_irq(struct usba_udc *udc, struct usba_ep *ep)
1346 {
1347         struct usba_request *req;
1348         u32 epstatus;
1349         u32 epctrl;
1350
1351 restart:
1352         epstatus = usba_ep_readl(ep, STA);
1353         epctrl = usba_ep_readl(ep, CTL);
1354
1355         DBG(DBG_INT, "%s [%d]: s/%08x c/%08x\n",
1356                         ep->ep.name, ep->state, epstatus, epctrl);
1357
1358         req = NULL;
1359         if (!list_empty(&ep->queue))
1360                 req = list_entry(ep->queue.next,
1361                                  struct usba_request, queue);
1362
1363         if ((epctrl & USBA_TX_PK_RDY) && !(epstatus & USBA_TX_PK_RDY)) {
1364                 if (req->submitted)
1365                         next_fifo_transaction(ep, req);
1366                 else
1367                         submit_request(ep, req);
1368
1369                 if (req->last_transaction) {
1370                         usba_ep_writel(ep, CTL_DIS, USBA_TX_PK_RDY);
1371                         usba_ep_writel(ep, CTL_ENB, USBA_TX_COMPLETE);
1372                 }
1373                 goto restart;
1374         }
1375         if ((epstatus & epctrl) & USBA_TX_COMPLETE) {
1376                 usba_ep_writel(ep, CLR_STA, USBA_TX_COMPLETE);
1377
1378                 switch (ep->state) {
1379                 case DATA_STAGE_IN:
1380                         usba_ep_writel(ep, CTL_ENB, USBA_RX_BK_RDY);
1381                         usba_ep_writel(ep, CTL_DIS, USBA_TX_COMPLETE);
1382                         ep->state = STATUS_STAGE_OUT;
1383                         break;
1384                 case STATUS_STAGE_ADDR:
1385                         /* Activate our new address */
1386                         usba_writel(udc, CTRL, (usba_readl(udc, CTRL)
1387                                                 | USBA_FADDR_EN));
1388                         usba_ep_writel(ep, CTL_DIS, USBA_TX_COMPLETE);
1389                         ep->state = WAIT_FOR_SETUP;
1390                         break;
1391                 case STATUS_STAGE_IN:
1392                         if (req) {
1393                                 list_del_init(&req->queue);
1394                                 request_complete(ep, req, 0);
1395                                 submit_next_request(ep);
1396                         }
1397                         usba_ep_writel(ep, CTL_DIS, USBA_TX_COMPLETE);
1398                         ep->state = WAIT_FOR_SETUP;
1399                         break;
1400                 case STATUS_STAGE_TEST:
1401                         usba_ep_writel(ep, CTL_DIS, USBA_TX_COMPLETE);
1402                         ep->state = WAIT_FOR_SETUP;
1403                         if (do_test_mode(udc))
1404                                 set_protocol_stall(udc, ep);
1405                         break;
1406                 default:
1407                         pr_err("udc: %s: TXCOMP: Invalid endpoint state %d, "
1408                                 "halting endpoint...\n",
1409                                 ep->ep.name, ep->state);
1410                         set_protocol_stall(udc, ep);
1411                         break;
1412                 }
1413
1414                 goto restart;
1415         }
1416         if ((epstatus & epctrl) & USBA_RX_BK_RDY) {
1417                 switch (ep->state) {
1418                 case STATUS_STAGE_OUT:
1419                         usba_ep_writel(ep, CLR_STA, USBA_RX_BK_RDY);
1420                         usba_ep_writel(ep, CTL_DIS, USBA_RX_BK_RDY);
1421
1422                         if (req) {
1423                                 list_del_init(&req->queue);
1424                                 request_complete(ep, req, 0);
1425                         }
1426                         ep->state = WAIT_FOR_SETUP;
1427                         break;
1428
1429                 case DATA_STAGE_OUT:
1430                         receive_data(ep);
1431                         break;
1432
1433                 default:
1434                         usba_ep_writel(ep, CLR_STA, USBA_RX_BK_RDY);
1435                         usba_ep_writel(ep, CTL_DIS, USBA_RX_BK_RDY);
1436                         pr_err("udc: %s: RXRDY: Invalid endpoint state %d, "
1437                                 "halting endpoint...\n",
1438                                 ep->ep.name, ep->state);
1439                         set_protocol_stall(udc, ep);
1440                         break;
1441                 }
1442
1443                 goto restart;
1444         }
1445         if (epstatus & USBA_RX_SETUP) {
1446                 union {
1447                         struct usb_ctrlrequest crq;
1448                         unsigned long data[2];
1449                 } crq;
1450                 unsigned int pkt_len;
1451                 int ret;
1452
1453                 if (ep->state != WAIT_FOR_SETUP) {
1454                         /*
1455                          * Didn't expect a SETUP packet at this
1456                          * point. Clean up any pending requests (which
1457                          * may be successful).
1458                          */
1459                         int status = -EPROTO;
1460
1461                         /*
1462                          * RXRDY and TXCOMP are dropped when SETUP
1463                          * packets arrive.  Just pretend we received
1464                          * the status packet.
1465                          */
1466                         if (ep->state == STATUS_STAGE_OUT
1467                                         || ep->state == STATUS_STAGE_IN) {
1468                                 usba_ep_writel(ep, CTL_DIS, USBA_RX_BK_RDY);
1469                                 status = 0;
1470                         }
1471
1472                         if (req) {
1473                                 list_del_init(&req->queue);
1474                                 request_complete(ep, req, status);
1475                         }
1476                 }
1477
1478                 pkt_len = USBA_BFEXT(BYTE_COUNT, usba_ep_readl(ep, STA));
1479                 DBG(DBG_HW, "Packet length: %u\n", pkt_len);
1480                 if (pkt_len != sizeof(crq)) {
1481                         pr_warning("udc: Invalid packet length %u "
1482                                 "(expected %zu)\n", pkt_len, sizeof(crq));
1483                         set_protocol_stall(udc, ep);
1484                         return;
1485                 }
1486
1487                 DBG(DBG_FIFO, "Copying ctrl request from 0x%p:\n", ep->fifo);
1488                 memcpy_fromio(crq.data, ep->fifo, sizeof(crq));
1489
1490                 /* Free up one bank in the FIFO so that we can
1491                  * generate or receive a reply right away. */
1492                 usba_ep_writel(ep, CLR_STA, USBA_RX_SETUP);
1493
1494                 /* printk(KERN_DEBUG "setup: %d: %02x.%02x\n",
1495                         ep->state, crq.crq.bRequestType,
1496                         crq.crq.bRequest); */
1497
1498                 if (crq.crq.bRequestType & USB_DIR_IN) {
1499                         /*
1500                          * The USB 2.0 spec states that "if wLength is
1501                          * zero, there is no data transfer phase."
1502                          * However, testusb #14 seems to actually
1503                          * expect a data phase even if wLength = 0...
1504                          */
1505                         ep->state = DATA_STAGE_IN;
1506                 } else {
1507                         if (crq.crq.wLength != __constant_cpu_to_le16(0))
1508                                 ep->state = DATA_STAGE_OUT;
1509                         else
1510                                 ep->state = STATUS_STAGE_IN;
1511                 }
1512
1513                 ret = -1;
1514                 if (ep->index == 0)
1515                         ret = handle_ep0_setup(udc, ep, &crq.crq);
1516                 else {
1517                         spin_unlock(&udc->lock);
1518                         ret = udc->driver->setup(&udc->gadget, &crq.crq);
1519                         spin_lock(&udc->lock);
1520                 }
1521
1522                 DBG(DBG_BUS, "req %02x.%02x, length %d, state %d, ret %d\n",
1523                         crq.crq.bRequestType, crq.crq.bRequest,
1524                         le16_to_cpu(crq.crq.wLength), ep->state, ret);
1525
1526                 if (ret < 0) {
1527                         /* Let the host know that we failed */
1528                         set_protocol_stall(udc, ep);
1529                 }
1530         }
1531 }
1532
1533 static void usba_ep_irq(struct usba_udc *udc, struct usba_ep *ep)
1534 {
1535         struct usba_request *req;
1536         u32 epstatus;
1537         u32 epctrl;
1538
1539         epstatus = usba_ep_readl(ep, STA);
1540         epctrl = usba_ep_readl(ep, CTL);
1541
1542         DBG(DBG_INT, "%s: interrupt, status: 0x%08x\n", ep->ep.name, epstatus);
1543
1544         while ((epctrl & USBA_TX_PK_RDY) && !(epstatus & USBA_TX_PK_RDY)) {
1545                 DBG(DBG_BUS, "%s: TX PK ready\n", ep->ep.name);
1546
1547                 if (list_empty(&ep->queue)) {
1548                         dev_warn(&udc->pdev->dev, "ep_irq: queue empty\n");
1549                         usba_ep_writel(ep, CTL_DIS, USBA_TX_PK_RDY);
1550                         return;
1551                 }
1552
1553                 req = list_entry(ep->queue.next, struct usba_request, queue);
1554
1555                 if (req->using_dma) {
1556                         /* Send a zero-length packet */
1557                         usba_ep_writel(ep, SET_STA,
1558                                         USBA_TX_PK_RDY);
1559                         usba_ep_writel(ep, CTL_DIS,
1560                                         USBA_TX_PK_RDY);
1561                         list_del_init(&req->queue);
1562                         submit_next_request(ep);
1563                         request_complete(ep, req, 0);
1564                 } else {
1565                         if (req->submitted)
1566                                 next_fifo_transaction(ep, req);
1567                         else
1568                                 submit_request(ep, req);
1569
1570                         if (req->last_transaction) {
1571                                 list_del_init(&req->queue);
1572                                 submit_next_request(ep);
1573                                 request_complete(ep, req, 0);
1574                         }
1575                 }
1576
1577                 epstatus = usba_ep_readl(ep, STA);
1578                 epctrl = usba_ep_readl(ep, CTL);
1579         }
1580         if ((epstatus & epctrl) & USBA_RX_BK_RDY) {
1581                 DBG(DBG_BUS, "%s: RX data ready\n", ep->ep.name);
1582                 receive_data(ep);
1583                 usba_ep_writel(ep, CLR_STA, USBA_RX_BK_RDY);
1584         }
1585 }
1586
1587 static void usba_dma_irq(struct usba_udc *udc, struct usba_ep *ep)
1588 {
1589         struct usba_request *req;
1590         u32 status, control, pending;
1591
1592         status = usba_dma_readl(ep, STATUS);
1593         control = usba_dma_readl(ep, CONTROL);
1594 #ifdef CONFIG_USB_GADGET_DEBUG_FS
1595         ep->last_dma_status = status;
1596 #endif
1597         pending = status & control;
1598         DBG(DBG_INT | DBG_DMA, "dma irq, s/%#08x, c/%#08x\n", status, control);
1599
1600         if (status & USBA_DMA_CH_EN) {
1601                 dev_err(&udc->pdev->dev,
1602                         "DMA_CH_EN is set after transfer is finished!\n");
1603                 dev_err(&udc->pdev->dev,
1604                         "status=%#08x, pending=%#08x, control=%#08x\n",
1605                         status, pending, control);
1606
1607                 /*
1608                  * try to pretend nothing happened. We might have to
1609                  * do something here...
1610                  */
1611         }
1612
1613         if (list_empty(&ep->queue))
1614                 /* Might happen if a reset comes along at the right moment */
1615                 return;
1616
1617         if (pending & (USBA_DMA_END_TR_ST | USBA_DMA_END_BUF_ST)) {
1618                 req = list_entry(ep->queue.next, struct usba_request, queue);
1619                 usba_update_req(ep, req, status);
1620
1621                 list_del_init(&req->queue);
1622                 submit_next_request(ep);
1623                 request_complete(ep, req, 0);
1624         }
1625 }
1626
1627 static irqreturn_t usba_udc_irq(int irq, void *devid)
1628 {
1629         struct usba_udc *udc = devid;
1630         u32 status;
1631         u32 dma_status;
1632         u32 ep_status;
1633
1634         spin_lock(&udc->lock);
1635
1636         status = usba_readl(udc, INT_STA);
1637         DBG(DBG_INT, "irq, status=%#08x\n", status);
1638
1639         if (status & USBA_DET_SUSPEND) {
1640                 toggle_bias(0);
1641                 usba_writel(udc, INT_CLR, USBA_DET_SUSPEND);
1642                 DBG(DBG_BUS, "Suspend detected\n");
1643                 if (udc->gadget.speed != USB_SPEED_UNKNOWN
1644                                 && udc->driver && udc->driver->suspend) {
1645                         spin_unlock(&udc->lock);
1646                         udc->driver->suspend(&udc->gadget);
1647                         spin_lock(&udc->lock);
1648                 }
1649         }
1650
1651         if (status & USBA_WAKE_UP) {
1652                 toggle_bias(1);
1653                 usba_writel(udc, INT_CLR, USBA_WAKE_UP);
1654                 DBG(DBG_BUS, "Wake Up CPU detected\n");
1655         }
1656
1657         if (status & USBA_END_OF_RESUME) {
1658                 usba_writel(udc, INT_CLR, USBA_END_OF_RESUME);
1659                 DBG(DBG_BUS, "Resume detected\n");
1660                 if (udc->gadget.speed != USB_SPEED_UNKNOWN
1661                                 && udc->driver && udc->driver->resume) {
1662                         spin_unlock(&udc->lock);
1663                         udc->driver->resume(&udc->gadget);
1664                         spin_lock(&udc->lock);
1665                 }
1666         }
1667
1668         dma_status = USBA_BFEXT(DMA_INT, status);
1669         if (dma_status) {
1670                 int i;
1671
1672                 for (i = 1; i < USBA_NR_ENDPOINTS; i++)
1673                         if (dma_status & (1 << i))
1674                                 usba_dma_irq(udc, &usba_ep[i]);
1675         }
1676
1677         ep_status = USBA_BFEXT(EPT_INT, status);
1678         if (ep_status) {
1679                 int i;
1680
1681                 for (i = 0; i < USBA_NR_ENDPOINTS; i++)
1682                         if (ep_status & (1 << i)) {
1683                                 if (ep_is_control(&usba_ep[i]))
1684                                         usba_control_irq(udc, &usba_ep[i]);
1685                                 else
1686                                         usba_ep_irq(udc, &usba_ep[i]);
1687                         }
1688         }
1689
1690         if (status & USBA_END_OF_RESET) {
1691                 struct usba_ep *ep0;
1692
1693                 usba_writel(udc, INT_CLR, USBA_END_OF_RESET);
1694                 reset_all_endpoints(udc);
1695
1696                 if (status & USBA_HIGH_SPEED) {
1697                         DBG(DBG_BUS, "High-speed bus reset detected\n");
1698                         udc->gadget.speed = USB_SPEED_HIGH;
1699                 } else {
1700                         DBG(DBG_BUS, "Full-speed bus reset detected\n");
1701                         udc->gadget.speed = USB_SPEED_FULL;
1702                 }
1703
1704                 ep0 = &usba_ep[0];
1705                 ep0->desc = &usba_ep0_desc;
1706                 ep0->state = WAIT_FOR_SETUP;
1707                 usba_ep_writel(ep0, CFG,
1708                                 (USBA_BF(EPT_SIZE, EP0_EPT_SIZE)
1709                                 | USBA_BF(EPT_TYPE, USBA_EPT_TYPE_CONTROL)
1710                                 | USBA_BF(BK_NUMBER, USBA_BK_NUMBER_ONE)));
1711                 usba_ep_writel(ep0, CTL_ENB,
1712                                 USBA_EPT_ENABLE | USBA_RX_SETUP);
1713                 usba_writel(udc, INT_ENB,
1714                                 (usba_readl(udc, INT_ENB)
1715                                 | USBA_BF(EPT_INT, 1)
1716                                 | USBA_DET_SUSPEND
1717                                 | USBA_END_OF_RESUME));
1718
1719                 if (!(usba_ep_readl(ep0, CFG) & USBA_EPT_MAPPED))
1720                         dev_warn(&udc->pdev->dev,
1721                                  "WARNING: EP0 configuration is invalid!\n");
1722         }
1723
1724         spin_unlock(&udc->lock);
1725
1726         return IRQ_HANDLED;
1727 }
1728
1729 static irqreturn_t usba_vbus_irq(int irq, void *devid)
1730 {
1731         struct usba_udc *udc = devid;
1732         int vbus;
1733
1734         /* debounce */
1735         udelay(10);
1736
1737         spin_lock(&udc->lock);
1738
1739         /* May happen if Vbus pin toggles during probe() */
1740         if (!udc->driver)
1741                 goto out;
1742
1743         vbus = gpio_get_value(udc->vbus_pin);
1744         if (vbus != udc->vbus_prev) {
1745                 if (vbus) {
1746                         toggle_bias(1);
1747                         usba_writel(udc, CTRL, USBA_ENABLE_MASK);
1748                         usba_writel(udc, INT_ENB, USBA_END_OF_RESET);
1749                 } else {
1750                         udc->gadget.speed = USB_SPEED_UNKNOWN;
1751                         reset_all_endpoints(udc);
1752                         toggle_bias(0);
1753                         usba_writel(udc, CTRL, USBA_DISABLE_MASK);
1754                         spin_unlock(&udc->lock);
1755                         udc->driver->disconnect(&udc->gadget);
1756                         spin_lock(&udc->lock);
1757                 }
1758                 udc->vbus_prev = vbus;
1759         }
1760
1761 out:
1762         spin_unlock(&udc->lock);
1763
1764         return IRQ_HANDLED;
1765 }
1766
1767 int usb_gadget_register_driver(struct usb_gadget_driver *driver)
1768 {
1769         struct usba_udc *udc = &the_udc;
1770         unsigned long flags;
1771         int ret;
1772
1773         if (!udc->pdev)
1774                 return -ENODEV;
1775
1776         spin_lock_irqsave(&udc->lock, flags);
1777         if (udc->driver) {
1778                 spin_unlock_irqrestore(&udc->lock, flags);
1779                 return -EBUSY;
1780         }
1781
1782         udc->devstatus = 1 << USB_DEVICE_SELF_POWERED;
1783         udc->driver = driver;
1784         udc->gadget.dev.driver = &driver->driver;
1785         spin_unlock_irqrestore(&udc->lock, flags);
1786
1787         clk_enable(udc->pclk);
1788         clk_enable(udc->hclk);
1789
1790         ret = driver->bind(&udc->gadget);
1791         if (ret) {
1792                 DBG(DBG_ERR, "Could not bind to driver %s: error %d\n",
1793                         driver->driver.name, ret);
1794                 goto err_driver_bind;
1795         }
1796
1797         DBG(DBG_GADGET, "registered driver `%s'\n", driver->driver.name);
1798
1799         udc->vbus_prev = 0;
1800         if (udc->vbus_pin != -1)
1801                 enable_irq(gpio_to_irq(udc->vbus_pin));
1802
1803         /* If Vbus is present, enable the controller and wait for reset */
1804         spin_lock_irqsave(&udc->lock, flags);
1805         if (vbus_is_present(udc) && udc->vbus_prev == 0) {
1806                 toggle_bias(1);
1807                 usba_writel(udc, CTRL, USBA_ENABLE_MASK);
1808                 usba_writel(udc, INT_ENB, USBA_END_OF_RESET);
1809         }
1810         spin_unlock_irqrestore(&udc->lock, flags);
1811
1812         return 0;
1813
1814 err_driver_bind:
1815         udc->driver = NULL;
1816         udc->gadget.dev.driver = NULL;
1817         return ret;
1818 }
1819 EXPORT_SYMBOL(usb_gadget_register_driver);
1820
1821 int usb_gadget_unregister_driver(struct usb_gadget_driver *driver)
1822 {
1823         struct usba_udc *udc = &the_udc;
1824         unsigned long flags;
1825
1826         if (!udc->pdev)
1827                 return -ENODEV;
1828         if (driver != udc->driver)
1829                 return -EINVAL;
1830
1831         if (udc->vbus_pin != -1)
1832                 disable_irq(gpio_to_irq(udc->vbus_pin));
1833
1834         spin_lock_irqsave(&udc->lock, flags);
1835         udc->gadget.speed = USB_SPEED_UNKNOWN;
1836         reset_all_endpoints(udc);
1837         spin_unlock_irqrestore(&udc->lock, flags);
1838
1839         /* This will also disable the DP pullup */
1840         toggle_bias(0);
1841         usba_writel(udc, CTRL, USBA_DISABLE_MASK);
1842
1843         driver->unbind(&udc->gadget);
1844         udc->gadget.dev.driver = NULL;
1845         udc->driver = NULL;
1846
1847         clk_disable(udc->hclk);
1848         clk_disable(udc->pclk);
1849
1850         DBG(DBG_GADGET, "unregistered driver `%s'\n", driver->driver.name);
1851
1852         return 0;
1853 }
1854 EXPORT_SYMBOL(usb_gadget_unregister_driver);
1855
1856 static int __init usba_udc_probe(struct platform_device *pdev)
1857 {
1858         struct usba_platform_data *pdata = pdev->dev.platform_data;
1859         struct resource *regs, *fifo;
1860         struct clk *pclk, *hclk;
1861         struct usba_udc *udc = &the_udc;
1862         int irq, ret, i;
1863
1864         regs = platform_get_resource(pdev, IORESOURCE_MEM, CTRL_IOMEM_ID);
1865         fifo = platform_get_resource(pdev, IORESOURCE_MEM, FIFO_IOMEM_ID);
1866         if (!regs || !fifo || !pdata)
1867                 return -ENXIO;
1868
1869         irq = platform_get_irq(pdev, 0);
1870         if (irq < 0)
1871                 return irq;
1872
1873         pclk = clk_get(&pdev->dev, "pclk");
1874         if (IS_ERR(pclk))
1875                 return PTR_ERR(pclk);
1876         hclk = clk_get(&pdev->dev, "hclk");
1877         if (IS_ERR(hclk)) {
1878                 ret = PTR_ERR(hclk);
1879                 goto err_get_hclk;
1880         }
1881
1882         udc->pdev = pdev;
1883         udc->pclk = pclk;
1884         udc->hclk = hclk;
1885         udc->vbus_pin = -1;
1886
1887         ret = -ENOMEM;
1888         udc->regs = ioremap(regs->start, regs->end - regs->start + 1);
1889         if (!udc->regs) {
1890                 dev_err(&pdev->dev, "Unable to map I/O memory, aborting.\n");
1891                 goto err_map_regs;
1892         }
1893         dev_info(&pdev->dev, "MMIO registers at 0x%08lx mapped at %p\n",
1894                  (unsigned long)regs->start, udc->regs);
1895         udc->fifo = ioremap(fifo->start, fifo->end - fifo->start + 1);
1896         if (!udc->fifo) {
1897                 dev_err(&pdev->dev, "Unable to map FIFO, aborting.\n");
1898                 goto err_map_fifo;
1899         }
1900         dev_info(&pdev->dev, "FIFO at 0x%08lx mapped at %p\n",
1901                  (unsigned long)fifo->start, udc->fifo);
1902
1903         device_initialize(&udc->gadget.dev);
1904         udc->gadget.dev.parent = &pdev->dev;
1905         udc->gadget.dev.dma_mask = pdev->dev.dma_mask;
1906
1907         platform_set_drvdata(pdev, udc);
1908
1909         /* Make sure we start from a clean slate */
1910         clk_enable(pclk);
1911         toggle_bias(0);
1912         usba_writel(udc, CTRL, USBA_DISABLE_MASK);
1913         clk_disable(pclk);
1914
1915         usba_ep = kmalloc(sizeof(struct usba_ep) * pdata->num_ep,
1916                           GFP_KERNEL);
1917         if (!usba_ep)
1918                 goto err_alloc_ep;
1919
1920         the_udc.gadget.ep0 = &usba_ep[0].ep;
1921
1922         INIT_LIST_HEAD(&usba_ep[0].ep.ep_list);
1923         usba_ep[0].ep_regs = udc->regs + USBA_EPT_BASE(0);
1924         usba_ep[0].dma_regs = udc->regs + USBA_DMA_BASE(0);
1925         usba_ep[0].fifo = udc->fifo + USBA_FIFO_BASE(0);
1926         usba_ep[0].ep.ops = &usba_ep_ops;
1927         usba_ep[0].ep.name = pdata->ep[0].name;
1928         usba_ep[0].ep.maxpacket = pdata->ep[0].fifo_size;
1929         usba_ep[0].udc = &the_udc;
1930         INIT_LIST_HEAD(&usba_ep[0].queue);
1931         usba_ep[0].fifo_size = pdata->ep[0].fifo_size;
1932         usba_ep[0].nr_banks = pdata->ep[0].nr_banks;
1933         usba_ep[0].index = pdata->ep[0].index;
1934         usba_ep[0].can_dma = pdata->ep[0].can_dma;
1935         usba_ep[0].can_isoc = pdata->ep[0].can_isoc;
1936
1937         for (i = 1; i < pdata->num_ep; i++) {
1938                 struct usba_ep *ep = &usba_ep[i];
1939
1940                 ep->ep_regs = udc->regs + USBA_EPT_BASE(i);
1941                 ep->dma_regs = udc->regs + USBA_DMA_BASE(i);
1942                 ep->fifo = udc->fifo + USBA_FIFO_BASE(i);
1943                 ep->ep.ops = &usba_ep_ops;
1944                 ep->ep.name = pdata->ep[i].name;
1945                 ep->ep.maxpacket = pdata->ep[i].fifo_size;
1946                 ep->udc = &the_udc;
1947                 INIT_LIST_HEAD(&ep->queue);
1948                 ep->fifo_size = pdata->ep[i].fifo_size;
1949                 ep->nr_banks = pdata->ep[i].nr_banks;
1950                 ep->index = pdata->ep[i].index;
1951                 ep->can_dma = pdata->ep[i].can_dma;
1952                 ep->can_isoc = pdata->ep[i].can_isoc;
1953
1954                 list_add_tail(&ep->ep.ep_list, &udc->gadget.ep_list);
1955         }
1956
1957         ret = request_irq(irq, usba_udc_irq, 0, "atmel_usba_udc", udc);
1958         if (ret) {
1959                 dev_err(&pdev->dev, "Cannot request irq %d (error %d)\n",
1960                         irq, ret);
1961                 goto err_request_irq;
1962         }
1963         udc->irq = irq;
1964
1965         ret = device_add(&udc->gadget.dev);
1966         if (ret) {
1967                 dev_dbg(&pdev->dev, "Could not add gadget: %d\n", ret);
1968                 goto err_device_add;
1969         }
1970
1971         if (pdata->vbus_pin >= 0) {
1972                 if (!gpio_request(pdata->vbus_pin, "atmel_usba_udc")) {
1973                         udc->vbus_pin = pdata->vbus_pin;
1974
1975                         ret = request_irq(gpio_to_irq(udc->vbus_pin),
1976                                         usba_vbus_irq, 0,
1977                                         "atmel_usba_udc", udc);
1978                         if (ret) {
1979                                 gpio_free(udc->vbus_pin);
1980                                 udc->vbus_pin = -1;
1981                                 dev_warn(&udc->pdev->dev,
1982                                          "failed to request vbus irq; "
1983                                          "assuming always on\n");
1984                         } else {
1985                                 disable_irq(gpio_to_irq(udc->vbus_pin));
1986                         }
1987                 }
1988         }
1989
1990         usba_init_debugfs(udc);
1991         for (i = 1; i < pdata->num_ep; i++)
1992                 usba_ep_init_debugfs(udc, &usba_ep[i]);
1993
1994         return 0;
1995
1996 err_device_add:
1997         free_irq(irq, udc);
1998 err_request_irq:
1999         kfree(usba_ep);
2000 err_alloc_ep:
2001         iounmap(udc->fifo);
2002 err_map_fifo:
2003         iounmap(udc->regs);
2004 err_map_regs:
2005         clk_put(hclk);
2006 err_get_hclk:
2007         clk_put(pclk);
2008
2009         platform_set_drvdata(pdev, NULL);
2010
2011         return ret;
2012 }
2013
2014 static int __exit usba_udc_remove(struct platform_device *pdev)
2015 {
2016         struct usba_udc *udc;
2017         int i;
2018         struct usba_platform_data *pdata = pdev->dev.platform_data;
2019
2020         udc = platform_get_drvdata(pdev);
2021
2022         for (i = 1; i < pdata->num_ep; i++)
2023                 usba_ep_cleanup_debugfs(&usba_ep[i]);
2024         usba_cleanup_debugfs(udc);
2025
2026         if (udc->vbus_pin != -1)
2027                 gpio_free(udc->vbus_pin);
2028
2029         free_irq(udc->irq, udc);
2030         kfree(usba_ep);
2031         iounmap(udc->fifo);
2032         iounmap(udc->regs);
2033         clk_put(udc->hclk);
2034         clk_put(udc->pclk);
2035
2036         device_unregister(&udc->gadget.dev);
2037
2038         return 0;
2039 }
2040
2041 static struct platform_driver udc_driver = {
2042         .remove         = __exit_p(usba_udc_remove),
2043         .driver         = {
2044                 .name           = "atmel_usba_udc",
2045                 .owner          = THIS_MODULE,
2046         },
2047 };
2048
2049 static int __init udc_init(void)
2050 {
2051         return platform_driver_probe(&udc_driver, usba_udc_probe);
2052 }
2053 module_init(udc_init);
2054
2055 static void __exit udc_exit(void)
2056 {
2057         platform_driver_unregister(&udc_driver);
2058 }
2059 module_exit(udc_exit);
2060
2061 MODULE_DESCRIPTION("Atmel USBA UDC driver");
2062 MODULE_AUTHOR("Haavard Skinnemoen <hskinnemoen@atmel.com>");
2063 MODULE_LICENSE("GPL");
2064 MODULE_ALIAS("platform:atmel_usba_udc");