5 this file has configuration informations - card-specific stuff
6 like the big tvcards array for the most part
8 Copyright (C) 1996,97,98 Ralph Metzler (rjkm@thp.uni-koeln.de)
9 & Marcus Metzler (mocm@thp.uni-koeln.de)
10 (c) 1999-2001 Gerd Knorr <kraxel@goldbach.in-berlin.de>
12 This program is free software; you can redistribute it and/or modify
13 it under the terms of the GNU General Public License as published by
14 the Free Software Foundation; either version 2 of the License, or
15 (at your option) any later version.
17 This program is distributed in the hope that it will be useful,
18 but WITHOUT ANY WARRANTY; without even the implied warranty of
19 MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
20 GNU General Public License for more details.
22 You should have received a copy of the GNU General Public License
23 along with this program; if not, write to the Free Software
24 Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA.
28 #include <linux/delay.h>
29 #include <linux/module.h>
30 #include <linux/kmod.h>
31 #include <linux/init.h>
32 #include <linux/pci.h>
33 #include <linux/vmalloc.h>
34 #include <linux/firmware.h>
35 #include <net/checksum.h>
37 #include <asm/unaligned.h>
41 #include <media/v4l2-common.h>
42 #include <media/tvaudio.h>
43 #include "bttv-audio-hook.h"
46 static void boot_msp34xx(struct bttv *btv, int pin);
47 static void boot_bt832(struct bttv *btv);
48 static void hauppauge_eeprom(struct bttv *btv);
49 static void avermedia_eeprom(struct bttv *btv);
50 static void osprey_eeprom(struct bttv *btv, const u8 ee[256]);
51 static void modtec_eeprom(struct bttv *btv);
52 static void init_PXC200(struct bttv *btv);
53 static void init_RTV24(struct bttv *btv);
55 static void rv605_muxsel(struct bttv *btv, unsigned int input);
56 static void eagle_muxsel(struct bttv *btv, unsigned int input);
57 static void xguard_muxsel(struct bttv *btv, unsigned int input);
58 static void ivc120_muxsel(struct bttv *btv, unsigned int input);
59 static void gvc1100_muxsel(struct bttv *btv, unsigned int input);
61 static void PXC200_muxsel(struct bttv *btv, unsigned int input);
63 static void picolo_tetra_muxsel(struct bttv *btv, unsigned int input);
64 static void picolo_tetra_init(struct bttv *btv);
66 static void tibetCS16_muxsel(struct bttv *btv, unsigned int input);
67 static void tibetCS16_init(struct bttv *btv);
69 static void kodicom4400r_muxsel(struct bttv *btv, unsigned int input);
70 static void kodicom4400r_init(struct bttv *btv);
72 static void sigmaSLC_muxsel(struct bttv *btv, unsigned int input);
73 static void sigmaSQ_muxsel(struct bttv *btv, unsigned int input);
75 static void geovision_muxsel(struct bttv *btv, unsigned int input);
77 static int terratec_active_radio_upgrade(struct bttv *btv);
78 static int tea5757_read(struct bttv *btv);
79 static int tea5757_write(struct bttv *btv, int value);
80 static void identify_by_eeprom(struct bttv *btv,
81 unsigned char eeprom_data[256]);
82 static int __devinit pvr_boot(struct bttv *btv);
84 /* config variables */
85 static unsigned int triton1;
86 static unsigned int vsfx;
87 static unsigned int latency = UNSET;
90 static unsigned int card[BTTV_MAX] = { [ 0 ... (BTTV_MAX-1) ] = UNSET };
91 static unsigned int pll[BTTV_MAX] = { [ 0 ... (BTTV_MAX-1) ] = UNSET };
92 static unsigned int tuner[BTTV_MAX] = { [ 0 ... (BTTV_MAX-1) ] = UNSET };
93 static unsigned int svhs[BTTV_MAX] = { [ 0 ... (BTTV_MAX-1) ] = UNSET };
94 static unsigned int remote[BTTV_MAX] = { [ 0 ... (BTTV_MAX-1) ] = UNSET };
95 static struct bttv *master[BTTV_MAX] = { [ 0 ... (BTTV_MAX-1) ] = NULL };
97 static unsigned int autoload = 1;
99 static unsigned int autoload;
101 static unsigned int gpiomask = UNSET;
102 static unsigned int audioall = UNSET;
103 static unsigned int audiomux[5] = { [ 0 ... 4 ] = UNSET };
106 module_param(triton1, int, 0444);
107 module_param(vsfx, int, 0444);
108 module_param(no_overlay, int, 0444);
109 module_param(latency, int, 0444);
110 module_param(gpiomask, int, 0444);
111 module_param(audioall, int, 0444);
112 module_param(autoload, int, 0444);
114 module_param_array(card, int, NULL, 0444);
115 module_param_array(pll, int, NULL, 0444);
116 module_param_array(tuner, int, NULL, 0444);
117 module_param_array(svhs, int, NULL, 0444);
118 module_param_array(remote, int, NULL, 0444);
119 module_param_array(audiomux, int, NULL, 0444);
121 MODULE_PARM_DESC(triton1,"set ETBF pci config bit "
122 "[enable bug compatibility for triton1 + others]");
123 MODULE_PARM_DESC(vsfx,"set VSFX pci config bit "
124 "[yet another chipset flaw workaround]");
125 MODULE_PARM_DESC(latency,"pci latency timer");
126 MODULE_PARM_DESC(card,"specify TV/grabber card model, see CARDLIST file for a list");
127 MODULE_PARM_DESC(pll,"specify installed crystal (0=none, 28=28 MHz, 35=35 MHz)");
128 MODULE_PARM_DESC(tuner,"specify installed tuner type");
129 MODULE_PARM_DESC(autoload,"automatically load i2c modules like tuner.o, default is 1 (yes)");
130 MODULE_PARM_DESC(no_overlay,"allow override overlay default (0 disables, 1 enables)"
131 " [some VIA/SIS chipsets are known to have problem with overlay]");
133 /* ----------------------------------------------------------------------- */
134 /* list of card IDs for bt878+ cards */
140 } cards[] __devinitdata = {
141 { 0x13eb0070, BTTV_BOARD_HAUPPAUGE878, "Hauppauge WinTV" },
142 { 0x39000070, BTTV_BOARD_HAUPPAUGE878, "Hauppauge WinTV-D" },
143 { 0x45000070, BTTV_BOARD_HAUPPAUGEPVR, "Hauppauge WinTV/PVR" },
144 { 0xff000070, BTTV_BOARD_OSPREY1x0, "Osprey-100" },
145 { 0xff010070, BTTV_BOARD_OSPREY2x0_SVID,"Osprey-200" },
146 { 0xff020070, BTTV_BOARD_OSPREY500, "Osprey-500" },
147 { 0xff030070, BTTV_BOARD_OSPREY2000, "Osprey-2000" },
148 { 0xff040070, BTTV_BOARD_OSPREY540, "Osprey-540" },
149 { 0xff070070, BTTV_BOARD_OSPREY440, "Osprey-440" },
151 { 0x00011002, BTTV_BOARD_ATI_TVWONDER, "ATI TV Wonder" },
152 { 0x00031002, BTTV_BOARD_ATI_TVWONDERVE,"ATI TV Wonder/VE" },
154 { 0x6606107d, BTTV_BOARD_WINFAST2000, "Leadtek WinFast TV 2000" },
155 { 0x6607107d, BTTV_BOARD_WINFASTVC100, "Leadtek WinFast VC 100" },
156 { 0x6609107d, BTTV_BOARD_WINFAST2000, "Leadtek TV 2000 XP" },
157 { 0x263610b4, BTTV_BOARD_STB2, "STB TV PCI FM, Gateway P/N 6000704" },
158 { 0x264510b4, BTTV_BOARD_STB2, "STB TV PCI FM, Gateway P/N 6000704" },
159 { 0x402010fc, BTTV_BOARD_GVBCTV3PCI, "I-O Data Co. GV-BCTV3/PCI" },
160 { 0x405010fc, BTTV_BOARD_GVBCTV4PCI, "I-O Data Co. GV-BCTV4/PCI" },
161 { 0x407010fc, BTTV_BOARD_GVBCTV5PCI, "I-O Data Co. GV-BCTV5/PCI" },
162 { 0xd01810fc, BTTV_BOARD_GVBCTV5PCI, "I-O Data Co. GV-BCTV5/PCI" },
164 { 0x001211bd, BTTV_BOARD_PINNACLE, "Pinnacle PCTV" },
165 /* some cards ship with byteswapped IDs ... */
166 { 0x1200bd11, BTTV_BOARD_PINNACLE, "Pinnacle PCTV [bswap]" },
167 { 0xff00bd11, BTTV_BOARD_PINNACLE, "Pinnacle PCTV [bswap]" },
168 /* this seems to happen as well ... */
169 { 0xff1211bd, BTTV_BOARD_PINNACLE, "Pinnacle PCTV" },
171 { 0x3000121a, BTTV_BOARD_VOODOOTV_200, "3Dfx VoodooTV 200" },
172 { 0x263710b4, BTTV_BOARD_VOODOOTV_FM, "3Dfx VoodooTV FM" },
173 { 0x3060121a, BTTV_BOARD_STB2, "3Dfx VoodooTV 100/ STB OEM" },
175 { 0x3000144f, BTTV_BOARD_MAGICTVIEW063, "(Askey Magic/others) TView99 CPH06x" },
176 { 0xa005144f, BTTV_BOARD_MAGICTVIEW063, "CPH06X TView99-Card" },
177 { 0x3002144f, BTTV_BOARD_MAGICTVIEW061, "(Askey Magic/others) TView99 CPH05x" },
178 { 0x3005144f, BTTV_BOARD_MAGICTVIEW061, "(Askey Magic/others) TView99 CPH061/06L (T1/LC)" },
179 { 0x5000144f, BTTV_BOARD_MAGICTVIEW061, "Askey CPH050" },
180 { 0x300014ff, BTTV_BOARD_MAGICTVIEW061, "TView 99 (CPH061)" },
181 { 0x300214ff, BTTV_BOARD_PHOEBE_TVMAS, "Phoebe TV Master (CPH060)" },
183 { 0x00011461, BTTV_BOARD_AVPHONE98, "AVerMedia TVPhone98" },
184 { 0x00021461, BTTV_BOARD_AVERMEDIA98, "AVermedia TVCapture 98" },
185 { 0x00031461, BTTV_BOARD_AVPHONE98, "AVerMedia TVPhone98" },
186 { 0x00041461, BTTV_BOARD_AVERMEDIA98, "AVerMedia TVCapture 98" },
187 { 0x03001461, BTTV_BOARD_AVERMEDIA98, "VDOMATE TV TUNER CARD" },
189 { 0x1117153b, BTTV_BOARD_TERRATVALUE, "Terratec TValue (Philips PAL B/G)" },
190 { 0x1118153b, BTTV_BOARD_TERRATVALUE, "Terratec TValue (Temic PAL B/G)" },
191 { 0x1119153b, BTTV_BOARD_TERRATVALUE, "Terratec TValue (Philips PAL I)" },
192 { 0x111a153b, BTTV_BOARD_TERRATVALUE, "Terratec TValue (Temic PAL I)" },
194 { 0x1123153b, BTTV_BOARD_TERRATVRADIO, "Terratec TV Radio+" },
195 { 0x1127153b, BTTV_BOARD_TERRATV, "Terratec TV+ (V1.05)" },
196 /* clashes with FlyVideo
197 *{ 0x18521852, BTTV_BOARD_TERRATV, "Terratec TV+ (V1.10)" }, */
198 { 0x1134153b, BTTV_BOARD_TERRATVALUE, "Terratec TValue (LR102)" },
199 { 0x1135153b, BTTV_BOARD_TERRATVALUER, "Terratec TValue Radio" }, /* LR102 */
200 { 0x5018153b, BTTV_BOARD_TERRATVALUE, "Terratec TValue" }, /* ?? */
201 { 0xff3b153b, BTTV_BOARD_TERRATVALUER, "Terratec TValue Radio" }, /* ?? */
203 { 0x400015b0, BTTV_BOARD_ZOLTRIX_GENIE, "Zoltrix Genie TV" },
204 { 0x400a15b0, BTTV_BOARD_ZOLTRIX_GENIE, "Zoltrix Genie TV" },
205 { 0x400d15b0, BTTV_BOARD_ZOLTRIX_GENIE, "Zoltrix Genie TV / Radio" },
206 { 0x401015b0, BTTV_BOARD_ZOLTRIX_GENIE, "Zoltrix Genie TV / Radio" },
207 { 0x401615b0, BTTV_BOARD_ZOLTRIX_GENIE, "Zoltrix Genie TV / Radio" },
209 { 0x1430aa00, BTTV_BOARD_PV143, "Provideo PV143A" },
210 { 0x1431aa00, BTTV_BOARD_PV143, "Provideo PV143B" },
211 { 0x1432aa00, BTTV_BOARD_PV143, "Provideo PV143C" },
212 { 0x1433aa00, BTTV_BOARD_PV143, "Provideo PV143D" },
213 { 0x1433aa03, BTTV_BOARD_PV143, "Security Eyes" },
215 { 0x1460aa00, BTTV_BOARD_PV150, "Provideo PV150A-1" },
216 { 0x1461aa01, BTTV_BOARD_PV150, "Provideo PV150A-2" },
217 { 0x1462aa02, BTTV_BOARD_PV150, "Provideo PV150A-3" },
218 { 0x1463aa03, BTTV_BOARD_PV150, "Provideo PV150A-4" },
220 { 0x1464aa04, BTTV_BOARD_PV150, "Provideo PV150B-1" },
221 { 0x1465aa05, BTTV_BOARD_PV150, "Provideo PV150B-2" },
222 { 0x1466aa06, BTTV_BOARD_PV150, "Provideo PV150B-3" },
223 { 0x1467aa07, BTTV_BOARD_PV150, "Provideo PV150B-4" },
225 { 0xa132ff00, BTTV_BOARD_IVC100, "IVC-100" },
226 { 0xa1550000, BTTV_BOARD_IVC200, "IVC-200" },
227 { 0xa1550001, BTTV_BOARD_IVC200, "IVC-200" },
228 { 0xa1550002, BTTV_BOARD_IVC200, "IVC-200" },
229 { 0xa1550003, BTTV_BOARD_IVC200, "IVC-200" },
230 { 0xa1550100, BTTV_BOARD_IVC200, "IVC-200G" },
231 { 0xa1550101, BTTV_BOARD_IVC200, "IVC-200G" },
232 { 0xa1550102, BTTV_BOARD_IVC200, "IVC-200G" },
233 { 0xa1550103, BTTV_BOARD_IVC200, "IVC-200G" },
234 { 0xa182ff00, BTTV_BOARD_IVC120, "IVC-120G" },
235 { 0xa182ff01, BTTV_BOARD_IVC120, "IVC-120G" },
236 { 0xa182ff02, BTTV_BOARD_IVC120, "IVC-120G" },
237 { 0xa182ff03, BTTV_BOARD_IVC120, "IVC-120G" },
238 { 0xa182ff04, BTTV_BOARD_IVC120, "IVC-120G" },
239 { 0xa182ff05, BTTV_BOARD_IVC120, "IVC-120G" },
240 { 0xa182ff06, BTTV_BOARD_IVC120, "IVC-120G" },
241 { 0xa182ff07, BTTV_BOARD_IVC120, "IVC-120G" },
242 { 0xa182ff08, BTTV_BOARD_IVC120, "IVC-120G" },
243 { 0xa182ff09, BTTV_BOARD_IVC120, "IVC-120G" },
244 { 0xa182ff0a, BTTV_BOARD_IVC120, "IVC-120G" },
245 { 0xa182ff0b, BTTV_BOARD_IVC120, "IVC-120G" },
246 { 0xa182ff0c, BTTV_BOARD_IVC120, "IVC-120G" },
247 { 0xa182ff0d, BTTV_BOARD_IVC120, "IVC-120G" },
248 { 0xa182ff0e, BTTV_BOARD_IVC120, "IVC-120G" },
249 { 0xa182ff0f, BTTV_BOARD_IVC120, "IVC-120G" },
251 { 0x41424344, BTTV_BOARD_GRANDTEC, "GrandTec Multi Capture" },
252 { 0x01020304, BTTV_BOARD_XGUARD, "Grandtec Grand X-Guard" },
254 { 0x18501851, BTTV_BOARD_CHRONOS_VS2, "FlyVideo 98 (LR50)/ Chronos Video Shuttle II" },
255 { 0xa0501851, BTTV_BOARD_CHRONOS_VS2, "FlyVideo 98 (LR50)/ Chronos Video Shuttle II" },
256 { 0x18511851, BTTV_BOARD_FLYVIDEO98EZ, "FlyVideo 98EZ (LR51)/ CyberMail AV" },
257 { 0x18521852, BTTV_BOARD_TYPHOON_TVIEW, "FlyVideo 98FM (LR50)/ Typhoon TView TV/FM Tuner" },
258 { 0x41a0a051, BTTV_BOARD_FLYVIDEO_98FM, "Lifeview FlyVideo 98 LR50 Rev Q" },
259 { 0x18501f7f, BTTV_BOARD_FLYVIDEO_98, "Lifeview Flyvideo 98" },
261 { 0x010115cb, BTTV_BOARD_GMV1, "AG GMV1" },
262 { 0x010114c7, BTTV_BOARD_MODTEC_205, "Modular Technology MM201/MM202/MM205/MM210/MM215 PCTV" },
264 { 0x10b42636, BTTV_BOARD_HAUPPAUGE878, "STB ???" },
265 { 0x217d6606, BTTV_BOARD_WINFAST2000, "Leadtek WinFast TV 2000" },
266 { 0xfff6f6ff, BTTV_BOARD_WINFAST2000, "Leadtek WinFast TV 2000" },
267 { 0x03116000, BTTV_BOARD_SENSORAY311, "Sensoray 311" },
268 { 0x00790e11, BTTV_BOARD_WINDVR, "Canopus WinDVR PCI" },
269 { 0xa0fca1a0, BTTV_BOARD_ZOLTRIX, "Face to Face Tvmax" },
270 { 0x82b2aa6a, BTTV_BOARD_SIMUS_GVC1100, "SIMUS GVC1100" },
271 { 0x146caa0c, BTTV_BOARD_PV951, "ituner spectra8" },
272 { 0x200a1295, BTTV_BOARD_PXC200, "ImageNation PXC200A" },
274 { 0x40111554, BTTV_BOARD_PV_BT878P_9B, "Prolink Pixelview PV-BT" },
275 { 0x17de0a01, BTTV_BOARD_KWORLD, "Mecer TV/FM/Video Tuner" },
277 { 0x01051805, BTTV_BOARD_PICOLO_TETRA_CHIP, "Picolo Tetra Chip #1" },
278 { 0x01061805, BTTV_BOARD_PICOLO_TETRA_CHIP, "Picolo Tetra Chip #2" },
279 { 0x01071805, BTTV_BOARD_PICOLO_TETRA_CHIP, "Picolo Tetra Chip #3" },
280 { 0x01081805, BTTV_BOARD_PICOLO_TETRA_CHIP, "Picolo Tetra Chip #4" },
282 { 0x15409511, BTTV_BOARD_ACORP_Y878F, "Acorp Y878F" },
284 { 0x53534149, BTTV_BOARD_SSAI_SECURITY, "SSAI Security Video Interface" },
285 { 0x5353414a, BTTV_BOARD_SSAI_ULTRASOUND, "SSAI Ultrasound Video Interface" },
287 /* likely broken, vendor id doesn't match the other magic views ...
288 * { 0xa0fca04f, BTTV_BOARD_MAGICTVIEW063, "Guillemot Maxi TV Video 3" }, */
290 /* Duplicate PCI ID, reconfigure for this board during the eeprom read.
291 * { 0x13eb0070, BTTV_BOARD_HAUPPAUGE_IMPACTVCB, "Hauppauge ImpactVCB" }, */
293 /* DVB cards (using pci function .1 for mpeg data xfer) */
294 { 0x001c11bd, BTTV_BOARD_PINNACLESAT, "Pinnacle PCTV Sat" },
295 { 0x01010071, BTTV_BOARD_NEBULA_DIGITV, "Nebula Electronics DigiTV" },
296 { 0x20007063, BTTV_BOARD_PC_HDTV, "pcHDTV HD-2000 TV"},
297 { 0x002611bd, BTTV_BOARD_TWINHAN_DST, "Pinnacle PCTV SAT CI" },
298 { 0x00011822, BTTV_BOARD_TWINHAN_DST, "Twinhan VisionPlus DVB" },
299 { 0xfc00270f, BTTV_BOARD_TWINHAN_DST, "ChainTech digitop DST-1000 DVB-S" },
300 { 0x07711461, BTTV_BOARD_AVDVBT_771, "AVermedia AverTV DVB-T 771" },
301 { 0x07611461, BTTV_BOARD_AVDVBT_761, "AverMedia AverTV DVB-T 761" },
302 { 0xdb1018ac, BTTV_BOARD_DVICO_DVBT_LITE, "DViCO FusionHDTV DVB-T Lite" },
303 { 0xdb1118ac, BTTV_BOARD_DVICO_DVBT_LITE, "Ultraview DVB-T Lite" },
304 { 0xd50018ac, BTTV_BOARD_DVICO_FUSIONHDTV_5_LITE, "DViCO FusionHDTV 5 Lite" },
305 { 0x00261822, BTTV_BOARD_TWINHAN_DST, "DNTV Live! Mini "},
306 { 0xd200dbc0, BTTV_BOARD_DVICO_FUSIONHDTV_2, "DViCO FusionHDTV 2" },
307 { 0x763c008a, BTTV_BOARD_GEOVISION_GV600, "GeoVision GV-600" },
312 /* ----------------------------------------------------------------------- */
313 /* array with description for bt848 / bt878 tv/grabber cards */
315 struct tvcard bttv_tvcards[] = {
316 /* ---- card 0x00 ---------------------------------- */
317 [BTTV_BOARD_UNKNOWN] = {
318 .name = " *** UNKNOWN/GENERIC *** ",
323 .muxsel = { 2, 3, 1, 0 },
325 .tuner_addr = ADDR_UNSET,
326 .radio_addr = ADDR_UNSET,
328 [BTTV_BOARD_MIRO] = {
335 .muxsel = { 2, 3, 1, 1 },
336 .gpiomux = { 2, 0, 0, 0 },
340 .tuner_addr = ADDR_UNSET,
341 .radio_addr = ADDR_UNSET,
343 [BTTV_BOARD_HAUPPAUGE] = {
344 .name = "Hauppauge (bt848)",
350 .muxsel = { 2, 3, 1, 1 },
351 .gpiomux = { 0, 1, 2, 3 },
355 .tuner_addr = ADDR_UNSET,
356 .radio_addr = ADDR_UNSET,
359 .name = "STB, Gateway P/N 6000699 (bt848)",
365 .muxsel = { 2, 3, 1, 1 },
366 .gpiomux = { 4, 0, 2, 3 },
370 .tuner_type = TUNER_PHILIPS_NTSC,
371 .tuner_addr = ADDR_UNSET,
372 .radio_addr = ADDR_UNSET,
377 /* ---- card 0x04 ---------------------------------- */
378 [BTTV_BOARD_INTEL] = {
379 .name = "Intel Create and Share PCI/ Smart Video Recorder III",
385 .muxsel = { 2, 3, 1, 1 },
388 .tuner_type = TUNER_ABSENT,
389 .tuner_addr = ADDR_UNSET,
390 .radio_addr = ADDR_UNSET,
392 [BTTV_BOARD_DIAMOND] = {
393 .name = "Diamond DTV2000",
399 .muxsel = { 2, 3, 1, 0 },
400 .gpiomux = { 0, 1, 0, 1 },
404 .tuner_addr = ADDR_UNSET,
405 .radio_addr = ADDR_UNSET,
407 [BTTV_BOARD_AVERMEDIA] = {
408 .name = "AVerMedia TVPhone",
413 .muxsel = { 2, 3, 1, 1 },
415 .gpiomux = { 0x0c, 0x04, 0x08, 0x04 },
416 /* 0x04 for some cards ?? */
419 .tuner_addr = ADDR_UNSET,
420 .radio_addr = ADDR_UNSET,
421 .audio_mode_gpio= avermedia_tvphone_audio,
424 [BTTV_BOARD_MATRIX_VISION] = {
425 .name = "MATRIX-Vision MV-Delta",
431 .muxsel = { 2, 3, 1, 0, 0 },
435 .tuner_addr = ADDR_UNSET,
436 .radio_addr = ADDR_UNSET,
439 /* ---- card 0x08 ---------------------------------- */
440 [BTTV_BOARD_FLYVIDEO] = {
441 .name = "Lifeview FlyVideo II (Bt848) LR26 / MAXI TV Video PCI2 LR26",
447 .muxsel = { 2, 3, 1, 1 },
448 .gpiomux = { 0, 0xc00, 0x800, 0x400 },
453 .tuner_addr = ADDR_UNSET,
454 .radio_addr = ADDR_UNSET,
456 [BTTV_BOARD_TURBOTV] = {
457 .name = "IMS/IXmicro TurboTV",
463 .muxsel = { 2, 3, 1, 1 },
464 .gpiomux = { 1, 1, 2, 3 },
467 .tuner_type = TUNER_TEMIC_PAL,
468 .tuner_addr = ADDR_UNSET,
469 .radio_addr = ADDR_UNSET,
471 [BTTV_BOARD_HAUPPAUGE878] = {
472 .name = "Hauppauge (bt878)",
477 .gpiomask = 0x0f, /* old: 7 */
478 .muxsel = { 2, 0, 1, 1 },
479 .gpiomux = { 0, 1, 2, 3 },
484 .tuner_addr = ADDR_UNSET,
485 .radio_addr = ADDR_UNSET,
487 [BTTV_BOARD_MIROPRO] = {
488 .name = "MIRO PCTV pro",
494 .muxsel = { 2, 3, 1, 1 },
495 .gpiomux = { 0x20001,0x10001, 0, 0 },
499 .tuner_addr = ADDR_UNSET,
500 .radio_addr = ADDR_UNSET,
503 /* ---- card 0x0c ---------------------------------- */
504 [BTTV_BOARD_ADSTECH_TV] = {
505 .name = "ADS Technologies Channel Surfer TV (bt848)",
511 .muxsel = { 2, 3, 1, 1 },
512 .gpiomux = { 13, 14, 11, 7 },
515 .tuner_addr = ADDR_UNSET,
516 .radio_addr = ADDR_UNSET,
518 [BTTV_BOARD_AVERMEDIA98] = {
519 .name = "AVerMedia TVCapture 98",
525 .muxsel = { 2, 3, 1, 1 },
526 .gpiomux = { 13, 14, 11, 7 },
530 .tuner_type = TUNER_PHILIPS_PAL,
531 .tuner_addr = ADDR_UNSET,
532 .radio_addr = ADDR_UNSET,
533 .audio_mode_gpio= avermedia_tv_stereo_audio,
537 .name = "Aimslab Video Highway Xtreme (VHX)",
543 .muxsel = { 2, 3, 1, 1 },
544 .gpiomux = { 0, 2, 1, 3 }, /* old: {0, 1, 2, 3, 4} */
549 .tuner_addr = ADDR_UNSET,
550 .radio_addr = ADDR_UNSET,
552 [BTTV_BOARD_ZOLTRIX] = {
553 .name = "Zoltrix TV-Max",
559 .muxsel = { 2, 3, 1, 1 },
560 .gpiomux = { 0, 0, 1, 0 },
564 .tuner_addr = ADDR_UNSET,
565 .radio_addr = ADDR_UNSET,
568 /* ---- card 0x10 ---------------------------------- */
569 [BTTV_BOARD_PIXVIEWPLAYTV] = {
570 .name = "Prolink Pixelview PlayTV (bt878)",
575 .gpiomask = 0x01fe00,
576 .muxsel = { 2, 3, 1, 1 },
577 /* 2003-10-20 by "Anton A. Arapov" <arapov@mail.ru> */
578 .gpiomux = { 0x001e00, 0, 0x018000, 0x014000 },
579 .gpiomute = 0x002000,
583 .tuner_addr = ADDR_UNSET,
584 .radio_addr = ADDR_UNSET,
586 [BTTV_BOARD_WINVIEW_601] = {
587 .name = "Leadtek WinView 601",
592 .gpiomask = 0x8300f8,
593 .muxsel = { 2, 3, 1, 1,0 },
594 .gpiomux = { 0x4fa007,0xcfa007,0xcfa007,0xcfa007 },
595 .gpiomute = 0xcfa007,
598 .tuner_addr = ADDR_UNSET,
599 .radio_addr = ADDR_UNSET,
600 .volume_gpio = winview_volume,
603 [BTTV_BOARD_AVEC_INTERCAP] = {
604 .name = "AVEC Intercapture",
610 .muxsel = { 2, 3, 1, 1 },
611 .gpiomux = { 1, 0, 0, 0 },
614 .tuner_addr = ADDR_UNSET,
615 .radio_addr = ADDR_UNSET,
617 [BTTV_BOARD_LIFE_FLYKIT] = {
618 .name = "Lifeview FlyVideo II EZ /FlyKit LR38 Bt848 (capture only)",
623 .gpiomask = 0x8dff00,
624 .muxsel = { 2, 3, 1, 1 },
628 .tuner_addr = ADDR_UNSET,
629 .radio_addr = ADDR_UNSET,
632 /* ---- card 0x14 ---------------------------------- */
633 [BTTV_BOARD_CEI_RAFFLES] = {
634 .name = "CEI Raffles Card",
639 .muxsel = { 2, 3, 1, 1 },
641 .tuner_addr = ADDR_UNSET,
642 .radio_addr = ADDR_UNSET,
644 [BTTV_BOARD_CONFERENCETV] = {
645 .name = "Lifeview FlyVideo 98/ Lucky Star Image World ConferenceTV LR50",
647 .audio_inputs = 2, /* tuner, line in */
651 .muxsel = { 2, 3, 1, 1 },
652 .gpiomux = { 0, 0x800, 0x1000, 0x1000 },
655 .tuner_type = TUNER_PHILIPS_PAL_I,
656 .tuner_addr = ADDR_UNSET,
657 .radio_addr = ADDR_UNSET,
659 [BTTV_BOARD_PHOEBE_TVMAS] = {
660 .name = "Askey CPH050/ Phoebe Tv Master + FM",
666 .muxsel = { 2, 3, 1, 1 },
667 .gpiomux = { 0, 1, 0x800, 0x400 },
672 .tuner_addr = ADDR_UNSET,
673 .radio_addr = ADDR_UNSET,
675 [BTTV_BOARD_MODTEC_205] = {
676 .name = "Modular Technology MM201/MM202/MM205/MM210/MM215 PCTV, bt878",
682 .muxsel = { 2, 3, -1 },
683 .digital_mode = DIGITAL_MODE_CAMERA,
684 .gpiomux = { 0, 0, 0, 0 },
687 .tuner_type = TUNER_ALPS_TSBB5_PAL_I,
688 .tuner_addr = ADDR_UNSET,
689 .radio_addr = ADDR_UNSET,
692 /* ---- card 0x18 ---------------------------------- */
693 [BTTV_BOARD_MAGICTVIEW061] = {
694 .name = "Askey CPH05X/06X (bt878) [many vendors]",
700 .muxsel = { 2, 3, 1, 1 },
701 .gpiomux = {0x400, 0x400, 0x400, 0x400 },
706 .tuner_addr = ADDR_UNSET,
707 .radio_addr = ADDR_UNSET,
710 [BTTV_BOARD_VOBIS_BOOSTAR] = {
711 .name = "Terratec TerraTV+ Version 1.0 (Bt848)/ Terra TValue Version 1.0/ Vobis TV-Boostar",
716 .gpiomask = 0x1f0fff,
717 .muxsel = { 2, 3, 1, 1 },
718 .gpiomux = { 0x20000, 0x30000, 0x10000, 0 },
721 .tuner_type = TUNER_PHILIPS_PAL,
722 .tuner_addr = ADDR_UNSET,
723 .radio_addr = ADDR_UNSET,
724 .audio_mode_gpio= terratv_audio,
726 [BTTV_BOARD_HAUPPAUG_WCAM] = {
727 .name = "Hauppauge WinCam newer (bt878)",
733 .muxsel = { 2, 0, 1, 1 },
734 .gpiomux = { 0, 1, 2, 3 },
738 .tuner_addr = ADDR_UNSET,
739 .radio_addr = ADDR_UNSET,
741 [BTTV_BOARD_MAXI] = {
742 .name = "Lifeview FlyVideo 98/ MAXI TV Video PCI2 LR50",
748 .muxsel = { 2, 3, 1, 1 },
749 .gpiomux = { 0, 0x800, 0x1000, 0x1000 },
752 .tuner_type = TUNER_PHILIPS_SECAM,
753 .tuner_addr = ADDR_UNSET,
754 .radio_addr = ADDR_UNSET,
757 /* ---- card 0x1c ---------------------------------- */
758 [BTTV_BOARD_TERRATV] = {
759 .name = "Terratec TerraTV+ Version 1.1 (bt878)",
764 .gpiomask = 0x1f0fff,
765 .muxsel = { 2, 3, 1, 1 },
766 .gpiomux = { 0x20000, 0x30000, 0x10000, 0x00000 },
769 .tuner_type = TUNER_PHILIPS_PAL,
770 .tuner_addr = ADDR_UNSET,
771 .radio_addr = ADDR_UNSET,
772 .audio_mode_gpio= terratv_audio,
774 External 20 pin connector (for Active Radio Upgrade board)
780 gpio05: om5610-stereo
784 gpio09+10: nIOR, nSEL ?? (bt878)
788 gpio16: u2-A0 (1st 4052bt)
791 gpio19: u4-A0 (2nd 4052)
795 00000 : Cdrom (internal audio input)
796 10000 : ext. Video audio input
805 [BTTV_BOARD_PXC200] = {
806 /* Jannik Fritsch <jannik@techfak.uni-bielefeld.de> */
807 .name = "Imagenation PXC200",
811 .svhs = 1, /* was: 4 */
813 .muxsel = { 2, 3, 1, 0, 0},
817 .tuner_addr = ADDR_UNSET,
818 .radio_addr = ADDR_UNSET,
819 .muxsel_hook = PXC200_muxsel,
822 [BTTV_BOARD_FLYVIDEO_98] = {
823 .name = "Lifeview FlyVideo 98 LR50",
828 .gpiomask = 0x1800, /* 0x8dfe00 */
829 .muxsel = { 2, 3, 1, 1 },
830 .gpiomux = { 0, 0x0800, 0x1000, 0x1000 },
834 .tuner_addr = ADDR_UNSET,
835 .radio_addr = ADDR_UNSET,
837 [BTTV_BOARD_IPROTV] = {
838 .name = "Formac iProTV, Formac ProTV I (bt848)",
844 .muxsel = { 2, 3, 1, 1 },
845 .gpiomux = { 1, 0, 0, 0 },
847 .tuner_type = TUNER_PHILIPS_PAL,
848 .tuner_addr = ADDR_UNSET,
849 .radio_addr = ADDR_UNSET,
852 /* ---- card 0x20 ---------------------------------- */
853 [BTTV_BOARD_INTEL_C_S_PCI] = {
854 .name = "Intel Create and Share PCI/ Smart Video Recorder III",
860 .muxsel = { 2, 3, 1, 1 },
863 .tuner_type = TUNER_ABSENT,
864 .tuner_addr = ADDR_UNSET,
865 .radio_addr = ADDR_UNSET,
867 [BTTV_BOARD_TERRATVALUE] = {
868 .name = "Terratec TerraTValue Version Bt878",
873 .gpiomask = 0xffff00,
874 .muxsel = { 2, 3, 1, 1 },
875 .gpiomux = { 0x500, 0, 0x300, 0x900 },
879 .tuner_type = TUNER_PHILIPS_PAL,
880 .tuner_addr = ADDR_UNSET,
881 .radio_addr = ADDR_UNSET,
883 [BTTV_BOARD_WINFAST2000] = {
884 .name = "Leadtek WinFast 2000/ WinFast 2000 XP",
889 .muxsel = { 2, 3, 1, 1, 0 }, /* TV, CVid, SVid, CVid over SVid connector */
890 /* Alexander Varakin <avarakin@hotmail.com> [stereo version] */
891 .gpiomask = 0xb33000,
892 .gpiomux = { 0x122000,0x1000,0x0000,0x620000 },
893 .gpiomute = 0x800000,
894 /* Audio Routing for "WinFast 2000 XP" (no tv stereo !)
895 gpio23 -- hef4052:nEnable (0x800000)
898 0x0000: external audio
902 Note: There exists another variant "Winfast 2000" with tv stereo !?
903 Note: eeprom only contains FF and pci subsystem id 107d:6606
908 .tuner_type = TUNER_PHILIPS_PAL, /* default for now, gpio reads BFFF06 for Pal bg+dk */
909 .tuner_addr = ADDR_UNSET,
910 .radio_addr = ADDR_UNSET,
911 .audio_mode_gpio= winfast2000_audio,
914 [BTTV_BOARD_CHRONOS_VS2] = {
915 .name = "Lifeview FlyVideo 98 LR50 / Chronos Video Shuttle II",
921 .muxsel = { 2, 3, 1, 1 },
922 .gpiomux = { 0, 0x800, 0x1000, 0x1000 },
926 .tuner_addr = ADDR_UNSET,
927 .radio_addr = ADDR_UNSET,
930 /* ---- card 0x24 ---------------------------------- */
931 [BTTV_BOARD_TYPHOON_TVIEW] = {
932 .name = "Lifeview FlyVideo 98FM LR50 / Typhoon TView TV/FM Tuner",
938 .muxsel = { 2, 3, 1, 1 },
939 .gpiomux = { 0, 0x800, 0x1000, 0x1000 },
943 .tuner_addr = ADDR_UNSET,
944 .radio_addr = ADDR_UNSET,
947 [BTTV_BOARD_PXELVWPLTVPRO] = {
948 .name = "Prolink PixelView PlayTV pro",
954 .muxsel = { 2, 3, 1, 1 },
955 .gpiomux = { 0x21, 0x20, 0x24, 0x2c },
960 .tuner_addr = ADDR_UNSET,
961 .radio_addr = ADDR_UNSET,
963 [BTTV_BOARD_MAGICTVIEW063] = {
964 .name = "Askey CPH06X TView99",
969 .gpiomask = 0x551e00,
970 .muxsel = { 2, 3, 1, 0 },
971 .gpiomux = { 0x551400, 0x551200, 0, 0 },
972 .gpiomute = 0x551c00,
975 .tuner_type = TUNER_PHILIPS_PAL_I,
976 .tuner_addr = ADDR_UNSET,
977 .radio_addr = ADDR_UNSET,
980 [BTTV_BOARD_PINNACLE] = {
981 .name = "Pinnacle PCTV Studio/Rave",
986 .gpiomask = 0x03000F,
987 .muxsel = { 2, 3, 1, 1 },
988 .gpiomux = { 2, 0xd0001, 0, 0 },
993 .tuner_addr = ADDR_UNSET,
994 .radio_addr = ADDR_UNSET,
997 /* ---- card 0x28 ---------------------------------- */
998 [BTTV_BOARD_STB2] = {
999 .name = "STB TV PCI FM, Gateway P/N 6000704 (bt878), 3Dfx VoodooTV 100",
1005 .muxsel = { 2, 3, 1, 1 },
1006 .gpiomux = { 4, 0, 2, 3 },
1010 .tuner_type = TUNER_PHILIPS_NTSC,
1011 .tuner_addr = ADDR_UNSET,
1012 .radio_addr = ADDR_UNSET,
1016 [BTTV_BOARD_AVPHONE98] = {
1017 .name = "AVerMedia TVPhone 98",
1023 .muxsel = { 2, 3, 1, 1 },
1024 .gpiomux = { 13, 4, 11, 7 },
1027 .tuner_type = UNSET,
1028 .tuner_addr = ADDR_UNSET,
1029 .radio_addr = ADDR_UNSET,
1031 .audio_mode_gpio= avermedia_tvphone_audio,
1033 [BTTV_BOARD_PV951] = {
1034 .name = "ProVideo PV951", /* pic16c54 */
1040 .muxsel = { 2, 3, 1, 1},
1041 .gpiomux = { 0, 0, 0, 0},
1045 .tuner_type = TUNER_PHILIPS_PAL_I,
1046 .tuner_addr = ADDR_UNSET,
1047 .radio_addr = ADDR_UNSET,
1049 [BTTV_BOARD_ONAIR_TV] = {
1050 .name = "Little OnAir TV",
1056 .muxsel = { 2, 3, 1, 1 },
1057 .gpiomux = { 0xff9ff6, 0xff9ff6, 0xff1ff7, 0 },
1058 .gpiomute = 0xff3ffc,
1060 .tuner_type = UNSET,
1061 .tuner_addr = ADDR_UNSET,
1062 .radio_addr = ADDR_UNSET,
1065 /* ---- card 0x2c ---------------------------------- */
1066 [BTTV_BOARD_SIGMA_TVII_FM] = {
1067 .name = "Sigma TVII-FM",
1073 .muxsel = { 2, 3, 1, 1 },
1074 .gpiomux = { 1, 1, 0, 2 },
1078 .tuner_type = UNSET,
1079 .tuner_addr = ADDR_UNSET,
1080 .radio_addr = ADDR_UNSET,
1082 [BTTV_BOARD_MATRIX_VISION2] = {
1083 .name = "MATRIX-Vision MV-Delta 2",
1089 .muxsel = { 2, 3, 1, 0, 0 },
1093 .tuner_type = UNSET,
1094 .tuner_addr = ADDR_UNSET,
1095 .radio_addr = ADDR_UNSET,
1097 [BTTV_BOARD_ZOLTRIX_GENIE] = {
1098 .name = "Zoltrix Genie TV/FM",
1103 .gpiomask = 0xbcf03f,
1104 .muxsel = { 2, 3, 1, 1 },
1105 .gpiomux = { 0xbc803f, 0xbc903f, 0xbcb03f, 0 },
1106 .gpiomute = 0xbcb03f,
1109 .tuner_type = TUNER_TEMIC_4039FR5_NTSC,
1110 .tuner_addr = ADDR_UNSET,
1111 .radio_addr = ADDR_UNSET,
1113 [BTTV_BOARD_TERRATVRADIO] = {
1114 .name = "Terratec TV/Radio+",
1119 .gpiomask = 0x70000,
1120 .muxsel = { 2, 3, 1, 1 },
1121 .gpiomux = { 0x20000, 0x30000, 0x10000, 0 },
1122 .gpiomute = 0x40000,
1126 .tuner_type = TUNER_PHILIPS_PAL_I,
1127 .tuner_addr = ADDR_UNSET,
1128 .radio_addr = ADDR_UNSET,
1132 /* ---- card 0x30 ---------------------------------- */
1133 [BTTV_BOARD_DYNALINK] = {
1134 .name = "Askey CPH03x/ Dynalink Magic TView",
1140 .muxsel = { 2, 3, 1, 1 },
1141 .gpiomux = {2,0,0,0 },
1145 .tuner_type = UNSET,
1146 .tuner_addr = ADDR_UNSET,
1147 .radio_addr = ADDR_UNSET,
1149 [BTTV_BOARD_GVBCTV3PCI] = {
1150 .name = "IODATA GV-BCTV3/PCI",
1155 .gpiomask = 0x010f00,
1156 .muxsel = {2, 3, 0, 0 },
1157 .gpiomux = {0x10000, 0, 0x10000, 0 },
1160 .tuner_type = TUNER_ALPS_TSHC6_NTSC,
1161 .tuner_addr = ADDR_UNSET,
1162 .radio_addr = ADDR_UNSET,
1163 .audio_mode_gpio= gvbctv3pci_audio,
1165 [BTTV_BOARD_PXELVWPLTVPAK] = {
1166 .name = "Prolink PV-BT878P+4E / PixelView PlayTV PAK / Lenco MXTV-9578 CP",
1171 .gpiomask = 0xAA0000,
1172 .muxsel = { 2,3,1,1,-1 },
1173 .digital_mode = DIGITAL_MODE_CAMERA,
1174 .gpiomux = { 0x20000, 0, 0x80000, 0x80000 },
1175 .gpiomute = 0xa8000,
1178 .tuner_type = TUNER_PHILIPS_PAL_I,
1179 .tuner_addr = ADDR_UNSET,
1180 .radio_addr = ADDR_UNSET,
1182 /* GPIO wiring: (different from Rev.4C !)
1183 GPIO17: U4.A0 (first hef4052bt)
1185 GPIO20: U5.A1 (second hef4052bt)
1187 GPIO22: BT832 Reset Line
1188 GPIO23: A5,A0, U5,nEN
1189 Note: At i2c=0x8a is a Bt832 chip, which changes to 0x88 after being reset via GPIO22
1192 [BTTV_BOARD_EAGLE] = {
1193 .name = "Eagle Wireless Capricorn2 (bt878A)",
1199 .muxsel = { 2, 0, 1, 1 },
1200 .gpiomux = { 0, 1, 2, 3 },
1203 .tuner_type = UNSET /* TUNER_ALPS_TMDH2_NTSC */,
1204 .tuner_addr = ADDR_UNSET,
1205 .radio_addr = ADDR_UNSET,
1208 /* ---- card 0x34 ---------------------------------- */
1209 [BTTV_BOARD_PINNACLEPRO] = {
1210 /* David Härdeman <david@2gen.com> */
1211 .name = "Pinnacle PCTV Studio Pro",
1216 .gpiomask = 0x03000F,
1217 .muxsel = { 2, 3, 1, 1 },
1218 .gpiomux = { 1, 0xd0001, 0, 0 },
1220 /* sound path (5 sources):
1221 MUX1 (mask 0x03), Enable Pin 0x08 (0=enable, 1=disable)
1224 2= Mono TV sound from Tuner
1226 MUX2 (mask 0x30000):
1228 1= FM stereo Radio from Tuner */
1231 .tuner_type = UNSET,
1232 .tuner_addr = ADDR_UNSET,
1233 .radio_addr = ADDR_UNSET,
1235 [BTTV_BOARD_TVIEW_RDS_FM] = {
1236 /* Claas Langbehn <claas@bigfoot.com>,
1237 Sven Grothklags <sven@upb.de> */
1238 .name = "Typhoon TView RDS + FM Stereo / KNC1 TV Station RDS",
1244 .muxsel = { 2, 3, 1, 1 },
1245 .gpiomux = { 0, 0, 0x10, 8 },
1249 .tuner_type = TUNER_PHILIPS_PAL,
1250 .tuner_addr = ADDR_UNSET,
1251 .radio_addr = ADDR_UNSET,
1254 [BTTV_BOARD_LIFETEC_9415] = {
1255 /* Tim Röstermundt <rosterm@uni-muenster.de>
1256 in de.comp.os.unix.linux.hardware:
1257 options bttv card=0 pll=1 radio=1 gpiomask=0x18e0
1258 gpiomux =0x44c71f,0x44d71f,0,0x44d71f,0x44dfff
1259 options tuner type=5 */
1260 .name = "Lifeview FlyVideo 2000 /FlyVideo A2/ Lifetec LT 9415 TV [LR90]",
1266 .muxsel = { 2, 3, 1, 1 },
1267 .gpiomux = { 0x0000,0x0800,0x1000,0x1000 },
1269 /* For cards with tda9820/tda9821:
1270 0x0000: Tuner normal stereo
1271 0x0080: Tuner A2 SAP (second audio program = Zweikanalton)
1272 0x0880: Tuner A2 stereo */
1274 .tuner_type = UNSET,
1275 .tuner_addr = ADDR_UNSET,
1276 .radio_addr = ADDR_UNSET,
1278 [BTTV_BOARD_BESTBUY_EASYTV] = {
1279 /* Miguel Angel Alvarez <maacruz@navegalia.com>
1280 old Easy TV BT848 version (model CPH031) */
1281 .name = "Askey CPH031/ BESTBUY Easy TV",
1287 .muxsel = { 2, 3, 1, 0 },
1288 .gpiomux = { 2, 0, 0, 0 },
1292 .tuner_type = TUNER_TEMIC_PAL,
1293 .tuner_addr = ADDR_UNSET,
1294 .radio_addr = ADDR_UNSET,
1297 /* ---- card 0x38 ---------------------------------- */
1298 [BTTV_BOARD_FLYVIDEO_98FM] = {
1299 /* Gordon Heydon <gjheydon@bigfoot.com ('98) */
1300 .name = "Lifeview FlyVideo 98FM LR50",
1306 .muxsel = { 2, 3, 1, 1 },
1307 .gpiomux = { 0, 0x800, 0x1000, 0x1000 },
1310 .tuner_type = TUNER_PHILIPS_PAL,
1311 .tuner_addr = ADDR_UNSET,
1312 .radio_addr = ADDR_UNSET,
1314 /* This is the ultimate cheapo capture card
1315 * just a BT848A on a small PCB!
1316 * Steve Hosgood <steve@equiinet.com> */
1317 [BTTV_BOARD_GRANDTEC] = {
1318 .name = "GrandTec 'Grand Video Capture' (Bt848)",
1329 .tuner_type = UNSET,
1330 .tuner_addr = ADDR_UNSET,
1331 .radio_addr = ADDR_UNSET,
1333 [BTTV_BOARD_ASKEY_CPH060] = {
1334 /* Daniel Herrington <daniel.herrington@home.com> */
1335 .name = "Askey CPH060/ Phoebe TV Master Only (No FM)",
1341 .muxsel = { 2, 3, 1, 1},
1342 .gpiomux = { 0x400, 0x400, 0x400, 0x400 },
1346 .tuner_type = TUNER_TEMIC_4036FY5_NTSC,
1347 .tuner_addr = ADDR_UNSET,
1348 .radio_addr = ADDR_UNSET,
1350 [BTTV_BOARD_ASKEY_CPH03X] = {
1351 /* Matti Mottus <mottus@physic.ut.ee> */
1352 .name = "Askey CPH03x TV Capturer",
1357 .gpiomask = 0x03000F,
1358 .muxsel = { 2, 3, 1, 0 },
1359 .gpiomux = { 2, 0, 0, 0 },
1362 .tuner_type = TUNER_TEMIC_PAL,
1363 .tuner_addr = ADDR_UNSET,
1364 .radio_addr = ADDR_UNSET,
1367 /* ---- card 0x3c ---------------------------------- */
1368 [BTTV_BOARD_MM100PCTV] = {
1369 /* Philip Blundell <philb@gnu.org> */
1370 .name = "Modular Technology MM100PCTV",
1376 .muxsel = { 2, 3, 1, 1 },
1377 .gpiomux = { 2, 0, 0, 1 },
1380 .tuner_type = TUNER_TEMIC_PAL,
1381 .tuner_addr = ADDR_UNSET,
1382 .radio_addr = ADDR_UNSET,
1384 [BTTV_BOARD_GMV1] = {
1385 /* Adrian Cox <adrian@humboldt.co.uk */
1386 .name = "AG Electronics GMV1",
1397 .tuner_type = UNSET,
1398 .tuner_addr = ADDR_UNSET,
1399 .radio_addr = ADDR_UNSET,
1401 [BTTV_BOARD_BESTBUY_EASYTV2] = {
1402 /* Miguel Angel Alvarez <maacruz@navegalia.com>
1403 new Easy TV BT878 version (model CPH061)
1404 special thanks to Informatica Mieres for providing the card */
1405 .name = "Askey CPH061/ BESTBUY Easy TV (bt878)",
1411 .muxsel = { 2, 3, 1, 0 },
1412 .gpiomux = { 1, 0, 4, 4 },
1416 .tuner_type = TUNER_PHILIPS_PAL,
1417 .tuner_addr = ADDR_UNSET,
1418 .radio_addr = ADDR_UNSET,
1420 [BTTV_BOARD_ATI_TVWONDER] = {
1421 /* Lukas Gebauer <geby@volny.cz> */
1422 .name = "ATI TV-Wonder",
1428 .muxsel = { 2, 3, 1, 0 },
1429 .gpiomux = { 0xbffe, 0, 0xbfff, 0 },
1432 .tuner_type = TUNER_TEMIC_4006FN5_MULTI_PAL,
1433 .tuner_addr = ADDR_UNSET,
1434 .radio_addr = ADDR_UNSET,
1437 /* ---- card 0x40 ---------------------------------- */
1438 [BTTV_BOARD_ATI_TVWONDERVE] = {
1439 /* Lukas Gebauer <geby@volny.cz> */
1440 .name = "ATI TV-Wonder VE",
1446 .muxsel = { 2, 3, 0, 1 },
1447 .gpiomux = { 0, 0, 1, 0 },
1450 .tuner_type = TUNER_TEMIC_4006FN5_MULTI_PAL,
1451 .tuner_addr = ADDR_UNSET,
1452 .radio_addr = ADDR_UNSET,
1454 [BTTV_BOARD_FLYVIDEO2000] = {
1455 /* DeeJay <deejay@westel900.net (2000S) */
1456 .name = "Lifeview FlyVideo 2000S LR90",
1462 .muxsel = { 2, 3, 0, 1 },
1463 /* Radio changed from 1e80 to 0x800 to make
1464 FlyVideo2000S in .hu happy (gm)*/
1465 /* -dk-???: set mute=0x1800 for tda9874h daughterboard */
1466 .gpiomux = { 0x0000,0x0800,0x1000,0x1000 },
1468 .audio_mode_gpio= fv2000s_audio,
1473 .tuner_type = TUNER_PHILIPS_PAL,
1474 .tuner_addr = ADDR_UNSET,
1475 .radio_addr = ADDR_UNSET,
1477 [BTTV_BOARD_TERRATVALUER] = {
1478 .name = "Terratec TValueRadio",
1483 .gpiomask = 0xffff00,
1484 .muxsel = { 2, 3, 1, 1 },
1485 .gpiomux = { 0x500, 0x500, 0x300, 0x900 },
1489 .tuner_type = TUNER_PHILIPS_PAL,
1490 .tuner_addr = ADDR_UNSET,
1491 .radio_addr = ADDR_UNSET,
1494 [BTTV_BOARD_GVBCTV4PCI] = {
1495 /* TANAKA Kei <peg00625@nifty.com> */
1496 .name = "IODATA GV-BCTV4/PCI",
1501 .gpiomask = 0x010f00,
1502 .muxsel = {2, 3, 0, 0 },
1503 .gpiomux = {0x10000, 0, 0x10000, 0 },
1506 .tuner_type = TUNER_SHARP_2U5JF5540_NTSC,
1507 .tuner_addr = ADDR_UNSET,
1508 .radio_addr = ADDR_UNSET,
1509 .audio_mode_gpio= gvbctv3pci_audio,
1512 /* ---- card 0x44 ---------------------------------- */
1513 [BTTV_BOARD_VOODOOTV_FM] = {
1514 .name = "3Dfx VoodooTV FM (Euro)",
1515 /* try "insmod msp3400 simple=0" if you have
1516 * sound problems with this card. */
1521 .gpiomask = 0x4f8a00,
1522 /* 0x100000: 1=MSP enabled (0=disable again)
1523 * 0x010000: Connected to "S0" on tda9880 (0=Pal/BG, 1=NTSC) */
1524 .gpiomux = {0x947fff, 0x987fff,0x947fff,0x947fff },
1525 .gpiomute = 0x947fff,
1526 /* tvtuner, radio, external,internal, mute, stereo
1527 * tuner, Composit, SVid, Composit-on-Svid-adapter */
1528 .muxsel = { 2, 3 ,0 ,1 },
1529 .tuner_type = TUNER_MT2032,
1530 .tuner_addr = ADDR_UNSET,
1531 .radio_addr = ADDR_UNSET,
1535 [BTTV_BOARD_VOODOOTV_200] = {
1536 .name = "VoodooTV 200 (USA)",
1537 /* try "insmod msp3400 simple=0" if you have
1538 * sound problems with this card. */
1543 .gpiomask = 0x4f8a00,
1544 /* 0x100000: 1=MSP enabled (0=disable again)
1545 * 0x010000: Connected to "S0" on tda9880 (0=Pal/BG, 1=NTSC) */
1546 .gpiomux = {0x947fff, 0x987fff,0x947fff,0x947fff },
1547 .gpiomute = 0x947fff,
1548 /* tvtuner, radio, external,internal, mute, stereo
1549 * tuner, Composit, SVid, Composit-on-Svid-adapter */
1550 .muxsel = { 2, 3 ,0 ,1 },
1551 .tuner_type = TUNER_MT2032,
1552 .tuner_addr = ADDR_UNSET,
1553 .radio_addr = ADDR_UNSET,
1557 [BTTV_BOARD_AIMMS] = {
1558 /* Philip Blundell <pb@nexus.co.uk> */
1559 .name = "Active Imaging AIMMS",
1563 .tuner_type = UNSET,
1564 .tuner_addr = ADDR_UNSET,
1565 .radio_addr = ADDR_UNSET,
1570 [BTTV_BOARD_PV_BT878P_PLUS] = {
1571 /* Tomasz Pyra <hellfire@sedez.iq.pl> */
1572 .name = "Prolink Pixelview PV-BT878P+ (Rev.4C,8E)",
1578 .muxsel = { 2, 3, 1, 1 },
1579 .gpiomux = { 0, 0, 11, 7 }, /* TV and Radio with same GPIO ! */
1583 .tuner_type = TUNER_LG_PAL_I_FM,
1584 .tuner_addr = ADDR_UNSET,
1585 .radio_addr = ADDR_UNSET,
1588 GPIO0: U4.A0 (hef4052bt)
1590 GPIO2: U4.A1 (second hef4052bt)
1591 GPIO3: U4.nEN, U5.A0, A5.nEN
1595 [BTTV_BOARD_FLYVIDEO98EZ] = {
1596 .name = "Lifeview FlyVideo 98EZ (capture only) LR51",
1601 .muxsel = { 2, 3, 1, 1 }, /* AV1, AV2, SVHS, CVid adapter on SVHS */
1604 .tuner_type = UNSET,
1605 .tuner_addr = ADDR_UNSET,
1606 .radio_addr = ADDR_UNSET,
1609 /* ---- card 0x48 ---------------------------------- */
1610 [BTTV_BOARD_PV_BT878P_9B] = {
1611 /* Dariusz Kowalewski <darekk@automex.pl> */
1612 .name = "Prolink Pixelview PV-BT878P+9B (PlayTV Pro rev.9B FM+NICAM)",
1618 .muxsel = { 2, 3, 1, 1 },
1619 .gpiomux = { 0x01, 0x00, 0x03, 0x03 },
1625 .tuner_type = TUNER_PHILIPS_PAL,
1626 .tuner_addr = ADDR_UNSET,
1627 .radio_addr = ADDR_UNSET,
1628 .audio_mode_gpio= pvbt878p9b_audio, /* Note: not all cards have stereo */
1629 .has_radio = 1, /* Note: not all cards have radio */
1636 GPIO20,22,23: R30,R29,R28
1639 [BTTV_BOARD_SENSORAY311] = {
1640 /* Clay Kunz <ckunz@mail.arc.nasa.gov> */
1641 /* you must jumper JP5 for the card to work */
1642 .name = "Sensoray 311",
1648 .muxsel = { 2, 3, 1, 0, 0 },
1651 .tuner_type = UNSET,
1652 .tuner_addr = ADDR_UNSET,
1653 .radio_addr = ADDR_UNSET,
1655 [BTTV_BOARD_RV605] = {
1656 /* Miguel Freitas <miguel@cetuc.puc-rio.br> */
1657 .name = "RemoteVision MX (RV605)",
1663 .gpiomask2 = 0x07ff,
1664 .muxsel = { 0x33, 0x13, 0x23, 0x43, 0xf3, 0x73, 0xe3, 0x03,
1665 0xd3, 0xb3, 0xc3, 0x63, 0x93, 0x53, 0x83, 0xa3 },
1668 .tuner_type = UNSET,
1669 .tuner_addr = ADDR_UNSET,
1670 .radio_addr = ADDR_UNSET,
1671 .muxsel_hook = rv605_muxsel,
1673 [BTTV_BOARD_POWERCLR_MTV878] = {
1674 .name = "Powercolor MTV878/ MTV878R/ MTV878F",
1679 .gpiomask = 0x1C800F, /* Bit0-2: Audio select, 8-12:remote control 14:remote valid 15:remote reset */
1680 .muxsel = { 2, 1, 1, },
1681 .gpiomux = { 0, 1, 2, 2 },
1684 .tuner_type = TUNER_PHILIPS_PAL,
1685 .tuner_addr = ADDR_UNSET,
1686 .radio_addr = ADDR_UNSET,
1691 /* ---- card 0x4c ---------------------------------- */
1692 [BTTV_BOARD_WINDVR] = {
1693 /* Masaki Suzuki <masaki@btree.org> */
1694 .name = "Canopus WinDVR PCI (COMPAQ Presario 3524JP, 5112JP)",
1699 .gpiomask = 0x140007,
1700 .muxsel = { 2, 3, 1, 1 },
1701 .gpiomux = { 0, 1, 2, 3 },
1703 .tuner_type = TUNER_PHILIPS_NTSC,
1704 .tuner_addr = ADDR_UNSET,
1705 .radio_addr = ADDR_UNSET,
1706 .audio_mode_gpio= windvr_audio,
1708 [BTTV_BOARD_GRANDTEC_MULTI] = {
1709 .name = "GrandTec Multi Capture Card (Bt878)",
1715 .muxsel = { 2, 3, 1, 0 },
1720 .tuner_type = UNSET,
1721 .tuner_addr = ADDR_UNSET,
1722 .radio_addr = ADDR_UNSET,
1724 [BTTV_BOARD_KWORLD] = {
1725 .name = "Jetway TV/Capture JW-TV878-FBK, Kworld KW-TV878RF",
1731 .muxsel = { 2, 3, 1, 1 }, /* Tuner, SVid, SVHS, SVid to SVHS connector */
1732 .gpiomux = { 0, 0, 4, 4 },/* Yes, this tuner uses the same audio output for TV and FM radio!
1733 * This card lacks external Audio In, so we mute it on Ext. & Int.
1734 * The PCB can take a sbx1637/sbx1673, wiring unknown.
1735 * This card lacks PCI subsystem ID, sigh.
1736 * gpiomux =1: lower volume, 2+3: mute
1737 * btwincap uses 0x80000/0x80003
1743 .tuner_type = TUNER_PHILIPS_PAL,
1744 .tuner_addr = ADDR_UNSET,
1745 .radio_addr = ADDR_UNSET,
1746 /* Samsung TCPA9095PC27A (BG+DK), philips compatible, w/FM, stereo and
1747 radio signal strength indicators work fine. */
1750 GPIO0,1: HEF4052 A0,A1
1751 GPIO2: HEF4052 nENABLE
1753 GPIO8-13: IRDC357 data0-5 (data6 n.c. ?) [chip not present on my card]
1757 ?? : mtu8b56ep microcontroller for IR (GPIO wiring unknown)*/
1759 [BTTV_BOARD_DSP_TCVIDEO] = {
1760 /* Arthur Tetzlaff-Deas, DSP Design Ltd <software@dspdesign.com> */
1761 .name = "DSP Design TCVIDEO",
1764 .muxsel = { 2, 3, 1, 0 },
1766 .tuner_type = UNSET,
1767 .tuner_addr = ADDR_UNSET,
1768 .radio_addr = ADDR_UNSET,
1771 /* ---- card 0x50 ---------------------------------- */
1772 [BTTV_BOARD_HAUPPAUGEPVR] = {
1773 .name = "Hauppauge WinTV PVR",
1778 .muxsel = { 2, 0, 1, 1 },
1781 .tuner_type = UNSET,
1782 .tuner_addr = ADDR_UNSET,
1783 .radio_addr = ADDR_UNSET,
1788 [BTTV_BOARD_GVBCTV5PCI] = {
1789 .name = "IODATA GV-BCTV5/PCI",
1794 .gpiomask = 0x0f0f80,
1795 .muxsel = {2, 3, 1, 0 },
1796 .gpiomux = {0x030000, 0x010000, 0, 0 },
1797 .gpiomute = 0x020000,
1800 .tuner_type = TUNER_PHILIPS_NTSC_M,
1801 .tuner_addr = ADDR_UNSET,
1802 .radio_addr = ADDR_UNSET,
1803 .audio_mode_gpio= gvbctv5pci_audio,
1806 [BTTV_BOARD_OSPREY1x0] = {
1807 .name = "Osprey 100/150 (878)", /* 0x1(2|3)-45C6-C1 */
1808 .video_inputs = 4, /* id-inputs-clock */
1812 .muxsel = { 3, 2, 0, 1 },
1814 .tuner_type = UNSET,
1815 .tuner_addr = ADDR_UNSET,
1816 .radio_addr = ADDR_UNSET,
1821 [BTTV_BOARD_OSPREY1x0_848] = {
1822 .name = "Osprey 100/150 (848)", /* 0x04-54C0-C1 & older boards */
1827 .muxsel = { 2, 3, 1 },
1829 .tuner_type = UNSET,
1830 .tuner_addr = ADDR_UNSET,
1831 .radio_addr = ADDR_UNSET,
1837 /* ---- card 0x54 ---------------------------------- */
1838 [BTTV_BOARD_OSPREY101_848] = {
1839 .name = "Osprey 101 (848)", /* 0x05-40C0-C1 */
1846 .tuner_type = UNSET,
1847 .tuner_addr = ADDR_UNSET,
1848 .radio_addr = ADDR_UNSET,
1853 [BTTV_BOARD_OSPREY1x1] = {
1854 .name = "Osprey 101/151", /* 0x1(4|5)-0004-C4 */
1861 .tuner_type = UNSET,
1862 .tuner_addr = ADDR_UNSET,
1863 .radio_addr = ADDR_UNSET,
1868 [BTTV_BOARD_OSPREY1x1_SVID] = {
1869 .name = "Osprey 101/151 w/ svid", /* 0x(16|17|20)-00C4-C1 */
1876 .tuner_type = UNSET,
1877 .tuner_addr = ADDR_UNSET,
1878 .radio_addr = ADDR_UNSET,
1883 [BTTV_BOARD_OSPREY2xx] = {
1884 .name = "Osprey 200/201/250/251", /* 0x1(8|9|E|F)-0004-C4 */
1891 .tuner_type = UNSET,
1892 .tuner_addr = ADDR_UNSET,
1893 .radio_addr = ADDR_UNSET,
1899 /* ---- card 0x58 ---------------------------------- */
1900 [BTTV_BOARD_OSPREY2x0_SVID] = {
1901 .name = "Osprey 200/250", /* 0x1(A|B)-00C4-C1 */
1908 .tuner_type = UNSET,
1909 .tuner_addr = ADDR_UNSET,
1910 .radio_addr = ADDR_UNSET,
1915 [BTTV_BOARD_OSPREY2x0] = {
1916 .name = "Osprey 210/220/230", /* 0x1(A|B)-04C0-C1 */
1923 .tuner_type = UNSET,
1924 .tuner_addr = ADDR_UNSET,
1925 .radio_addr = ADDR_UNSET,
1930 [BTTV_BOARD_OSPREY500] = {
1931 .name = "Osprey 500", /* 500 */
1938 .tuner_type = UNSET,
1939 .tuner_addr = ADDR_UNSET,
1940 .radio_addr = ADDR_UNSET,
1945 [BTTV_BOARD_OSPREY540] = {
1946 .name = "Osprey 540", /* 540 */
1951 .tuner_type = UNSET,
1952 .tuner_addr = ADDR_UNSET,
1953 .radio_addr = ADDR_UNSET,
1959 /* ---- card 0x5C ---------------------------------- */
1960 [BTTV_BOARD_OSPREY2000] = {
1961 .name = "Osprey 2000", /* 2000 */
1968 .tuner_type = UNSET,
1969 .tuner_addr = ADDR_UNSET,
1970 .radio_addr = ADDR_UNSET,
1973 .no_tda7432 = 1, /* must avoid, conflicts with the bt860 */
1975 [BTTV_BOARD_IDS_EAGLE] = {
1976 /* M G Berberich <berberic@forwiss.uni-passau.de> */
1977 .name = "IDS Eagle",
1981 .tuner_type = UNSET,
1982 .tuner_addr = ADDR_UNSET,
1983 .radio_addr = ADDR_UNSET,
1986 .muxsel = { 0, 1, 2, 3 },
1987 .muxsel_hook = eagle_muxsel,
1992 [BTTV_BOARD_PINNACLESAT] = {
1993 .name = "Pinnacle PCTV Sat",
1998 .tuner_type = UNSET,
1999 .tuner_addr = ADDR_UNSET,
2000 .radio_addr = ADDR_UNSET,
2009 [BTTV_BOARD_FORMAC_PROTV] = {
2010 .name = "Formac ProTV II (bt878)",
2016 /* TV, Comp1, Composite over SVID con, SVID */
2017 .muxsel = { 2, 3, 1, 1 },
2018 .gpiomux = { 2, 2, 0, 0 },
2021 .tuner_type = TUNER_PHILIPS_PAL,
2022 .tuner_addr = ADDR_UNSET,
2023 .radio_addr = ADDR_UNSET,
2025 GPIO=0x00,0x01,0x03: mute (?)
2026 0x02: both TV and radio (tuner: FM1216/I)
2027 The card has onboard audio connectors labeled "cdrom" and "board",
2028 not soldered here, though unknown wiring.
2029 Card lacks: external audio in, pci subsystem id.
2033 /* ---- card 0x60 ---------------------------------- */
2034 [BTTV_BOARD_MACHTV] = {
2041 .muxsel = { 2, 3, 1, 1},
2042 .gpiomux = { 0, 1, 2, 3},
2045 .tuner_type = TUNER_PHILIPS_PAL,
2046 .tuner_addr = ADDR_UNSET,
2047 .radio_addr = ADDR_UNSET,
2050 [BTTV_BOARD_EURESYS_PICOLO] = {
2051 .name = "Euresys Picolo",
2060 .muxsel = { 2, 0, 1},
2062 .tuner_type = UNSET,
2063 .tuner_addr = ADDR_UNSET,
2064 .radio_addr = ADDR_UNSET,
2066 [BTTV_BOARD_PV150] = {
2067 /* Luc Van Hoeylandt <luc@e-magic.be> */
2068 .name = "ProVideo PV150", /* 0x4f */
2079 .tuner_type = UNSET,
2080 .tuner_addr = ADDR_UNSET,
2081 .radio_addr = ADDR_UNSET,
2083 [BTTV_BOARD_AD_TVK503] = {
2084 /* Hiroshi Takekawa <sian@big.or.jp> */
2085 /* This card lacks subsystem ID */
2086 .name = "AD-TVK503", /* 0x63 */
2091 .gpiomask = 0x001e8007,
2092 .muxsel = { 2, 3, 1, 0 },
2093 /* Tuner, Radio, external, internal, off, on */
2094 .gpiomux = { 0x08, 0x0f, 0x0a, 0x08 },
2099 .tuner_type = TUNER_PHILIPS_NTSC,
2100 .tuner_addr = ADDR_UNSET,
2101 .radio_addr = ADDR_UNSET,
2102 .audio_mode_gpio= adtvk503_audio,
2105 /* ---- card 0x64 ---------------------------------- */
2106 [BTTV_BOARD_HERCULES_SM_TV] = {
2107 .name = "Hercules Smart TV Stereo",
2113 .muxsel = { 2, 3, 1, 1 },
2117 .tuner_type = TUNER_PHILIPS_PAL,
2118 .tuner_addr = ADDR_UNSET,
2119 .radio_addr = ADDR_UNSET,
2121 - card lacks subsystem ID
2122 - stereo variant w/ daughter board with tda9874a @0xb0
2124 always from tda9874 independent of GPIO (?)
2125 external line in: unknown
2126 - Other chips: em78p156elp @ 0x96 (probably IR remote control)
2127 hef4053 (instead 4052) for unknown function
2130 [BTTV_BOARD_PACETV] = {
2131 .name = "Pace TV & Radio Card",
2136 .muxsel = { 2, 3, 1, 1 }, /* Tuner, CVid, SVid, CVid over SVid connector */
2140 .tuner_type = TUNER_PHILIPS_PAL_I,
2141 .tuner_addr = ADDR_UNSET,
2142 .radio_addr = ADDR_UNSET,
2145 /* Bt878, Bt832, FI1246 tuner; no pci subsystem id
2146 only internal line out: (4pin header) RGGL
2147 Radio must be decoded by msp3410d (not routed through)*/
2149 .digital_mode = DIGITAL_MODE_CAMERA, todo!
2152 [BTTV_BOARD_IVC200] = {
2153 /* Chris Willing <chris@vislab.usyd.edu.au> */
2158 .tuner_type = UNSET,
2159 .tuner_addr = ADDR_UNSET,
2160 .radio_addr = ADDR_UNSET,
2166 [BTTV_BOARD_XGUARD] = {
2167 .name = "Grand X-Guard / Trust 814PCI",
2172 .tuner_type = TUNER_ABSENT,
2173 .tuner_addr = ADDR_UNSET,
2174 .radio_addr = ADDR_UNSET,
2176 .muxsel = { 2,2,2,2, 3,3,3,3, 1,1,1,1, 0,0,0,0 },
2177 .muxsel_hook = xguard_muxsel,
2184 /* ---- card 0x68 ---------------------------------- */
2185 [BTTV_BOARD_NEBULA_DIGITV] = {
2186 .name = "Nebula Electronics DigiTV",
2190 .muxsel = { 2, 3, 1, 0 },
2195 .tuner_type = UNSET,
2196 .tuner_addr = ADDR_UNSET,
2197 .radio_addr = ADDR_UNSET,
2203 [BTTV_BOARD_PV143] = {
2204 /* Jorge Boncompte - DTI2 <jorge@dti2.net> */
2205 .name = "ProVideo PV143",
2211 .muxsel = { 2, 3, 1, 0 },
2216 .tuner_type = UNSET,
2217 .tuner_addr = ADDR_UNSET,
2218 .radio_addr = ADDR_UNSET,
2220 [BTTV_BOARD_VD009X1_MINIDIN] = {
2221 /* M.Klahr@phytec.de */
2222 .name = "PHYTEC VD-009-X1 MiniDIN (bt878)",
2225 .tuner = UNSET, /* card has no tuner */
2228 .muxsel = { 2, 3, 1, 0 },
2229 .gpiomux = { 0, 0, 0, 0 }, /* card has no audio */
2232 .tuner_type = UNSET,
2233 .tuner_addr = ADDR_UNSET,
2234 .radio_addr = ADDR_UNSET,
2236 [BTTV_BOARD_VD009X1_COMBI] = {
2237 .name = "PHYTEC VD-009-X1 Combi (bt878)",
2240 .tuner = UNSET, /* card has no tuner */
2243 .muxsel = { 2, 3, 1, 1 },
2244 .gpiomux = { 0, 0, 0, 0 }, /* card has no audio */
2247 .tuner_type = UNSET,
2248 .tuner_addr = ADDR_UNSET,
2249 .radio_addr = ADDR_UNSET,
2252 /* ---- card 0x6c ---------------------------------- */
2253 [BTTV_BOARD_VD009_MINIDIN] = {
2254 .name = "PHYTEC VD-009 MiniDIN (bt878)",
2257 .tuner = UNSET, /* card has no tuner */
2260 .gpiomask2 = 0x03, /* gpiomask2 defines the bits used to switch audio
2261 via the upper nibble of muxsel. here: used for
2262 xternal video-mux */
2263 .muxsel = { 0x02, 0x12, 0x22, 0x32, 0x03, 0x13, 0x23, 0x33, 0x01, 0x00 },
2264 .gpiomux = { 0, 0, 0, 0 }, /* card has no audio */
2267 .tuner_type = UNSET,
2268 .tuner_addr = ADDR_UNSET,
2269 .radio_addr = ADDR_UNSET,
2271 [BTTV_BOARD_VD009_COMBI] = {
2272 .name = "PHYTEC VD-009 Combi (bt878)",
2275 .tuner = UNSET, /* card has no tuner */
2278 .gpiomask2 = 0x03, /* gpiomask2 defines the bits used to switch audio
2279 via the upper nibble of muxsel. here: used for
2280 xternal video-mux */
2281 .muxsel = { 0x02, 0x12, 0x22, 0x32, 0x03, 0x13, 0x23, 0x33, 0x01, 0x01 },
2282 .gpiomux = { 0, 0, 0, 0 }, /* card has no audio */
2285 .tuner_type = UNSET,
2286 .tuner_addr = ADDR_UNSET,
2287 .radio_addr = ADDR_UNSET,
2289 [BTTV_BOARD_IVC100] = {
2294 .tuner_type = UNSET,
2295 .tuner_addr = ADDR_UNSET,
2296 .radio_addr = ADDR_UNSET,
2299 .muxsel = { 2, 3, 1, 0 },
2302 [BTTV_BOARD_IVC120] = {
2303 /* IVC-120G - Alan Garfield <alan@fromorbit.com> */
2306 .audio_inputs = 0, /* card has no audio */
2307 .tuner = UNSET, /* card has no tuner */
2308 .tuner_type = UNSET,
2309 .tuner_addr = ADDR_UNSET,
2310 .radio_addr = ADDR_UNSET,
2311 .svhs = UNSET, /* card has no svhs */
2317 .muxsel = { 0x01, 0x02, 0x03, 0x04, 0x05, 0x06, 0x07, 0x08,
2318 0x09, 0x0a, 0x0b, 0x0c, 0x0d, 0x0e, 0x0f, 0x10 },
2319 .muxsel_hook = ivc120_muxsel,
2323 /* ---- card 0x70 ---------------------------------- */
2324 [BTTV_BOARD_PC_HDTV] = {
2325 .name = "pcHDTV HD-2000 TV",
2330 .muxsel = { 2, 3, 1, 0 },
2331 .tuner_type = TUNER_PHILIPS_FCV1236D,
2332 .tuner_addr = ADDR_UNSET,
2333 .radio_addr = ADDR_UNSET,
2336 [BTTV_BOARD_TWINHAN_DST] = {
2337 .name = "Twinhan DST + clones",
2341 .tuner_type = TUNER_ABSENT,
2342 .tuner_addr = ADDR_UNSET,
2343 .radio_addr = ADDR_UNSET,
2347 [BTTV_BOARD_WINFASTVC100] = {
2348 .name = "Winfast VC100",
2353 .muxsel = { 3, 1, 1, 3 }, /* Vid In, SVid In, Vid over SVid in connector */
2357 .tuner_type = TUNER_ABSENT,
2358 .tuner_addr = ADDR_UNSET,
2359 .radio_addr = ADDR_UNSET,
2362 [BTTV_BOARD_TEV560] = {
2363 .name = "Teppro TEV-560/InterVision IV-560",
2369 .muxsel = { 2, 3, 1, 1 },
2370 .gpiomux = { 1, 1, 1, 1 },
2372 .tuner_type = TUNER_PHILIPS_PAL,
2373 .tuner_addr = ADDR_UNSET,
2374 .radio_addr = ADDR_UNSET,
2378 /* ---- card 0x74 ---------------------------------- */
2379 [BTTV_BOARD_SIMUS_GVC1100] = {
2380 .name = "SIMUS GVC1100",
2385 .tuner_type = UNSET,
2386 .tuner_addr = ADDR_UNSET,
2387 .radio_addr = ADDR_UNSET,
2389 .muxsel = { 2, 2, 2, 2 },
2391 .muxsel_hook = gvc1100_muxsel,
2393 [BTTV_BOARD_NGSTV_PLUS] = {
2394 /* Carlos Silva r3pek@r3pek.homelinux.org || card 0x75 */
2395 .name = "NGS NGSTV+",
2399 .gpiomask = 0x008007,
2400 .muxsel = { 2, 3, 0, 0 },
2401 .gpiomux = { 0, 0, 0, 0 },
2402 .gpiomute = 0x000003,
2404 .tuner_type = TUNER_PHILIPS_PAL,
2405 .tuner_addr = ADDR_UNSET,
2406 .radio_addr = ADDR_UNSET,
2409 [BTTV_BOARD_LMLBT4] = {
2410 /* http://linuxmedialabs.com */
2412 .video_inputs = 4, /* IN1,IN2,IN3,IN4 */
2416 .muxsel = { 2, 3, 1, 0 },
2421 .tuner_type = UNSET,
2422 .tuner_addr = ADDR_UNSET,
2423 .radio_addr = ADDR_UNSET,
2425 [BTTV_BOARD_TEKRAM_M205] = {
2426 /* Helmroos Harri <harri.helmroos@pp.inet.fi> */
2427 .name = "Tekram M205 PRO",
2431 .tuner_type = TUNER_PHILIPS_PAL,
2432 .tuner_addr = ADDR_UNSET,
2433 .radio_addr = ADDR_UNSET,
2437 .muxsel = { 2, 3, 1 },
2438 .gpiomux = { 0x68, 0x68, 0x61, 0x61 },
2442 /* ---- card 0x78 ---------------------------------- */
2443 [BTTV_BOARD_CONTVFMI] = {
2444 /* Javier Cendan Ares <jcendan@lycos.es> */
2445 /* bt878 TV + FM without subsystem ID */
2446 .name = "Conceptronic CONTVFMi",
2451 .gpiomask = 0x008007,
2452 .muxsel = { 2, 3, 1, 1 },
2453 .gpiomux = { 0, 1, 2, 2 },
2457 .tuner_type = TUNER_PHILIPS_PAL,
2458 .tuner_addr = ADDR_UNSET,
2459 .radio_addr = ADDR_UNSET,
2463 [BTTV_BOARD_PICOLO_TETRA_CHIP] = {
2464 /*Eric DEBIEF <debief@telemsa.com>*/
2465 /*EURESYS Picolo Tetra : 4 Conexant Fusion 878A, no audio, video input set with analog multiplexers GPIO controled*/
2466 /* adds picolo_tetra_muxsel(), picolo_tetra_init(), the folowing declaration strucure, and #define BTTV_BOARD_PICOLO_TETRA_CHIP*/
2468 .name = "Euresys Picolo Tetra",
2474 .gpiomask2 = 0x3C<<16,/*Set the GPIO[18]->GPIO[21] as output pin.==> drive the video inputs through analog multiplexers*/
2478 .muxsel = {2,2,2,2},/*878A input is always MUX0, see above.*/
2479 .gpiomux = { 0, 0, 0, 0 }, /* card has no audio */
2482 .muxsel_hook = picolo_tetra_muxsel,/*Required as it doesn't follow the classic input selection policy*/
2483 .tuner_type = UNSET,
2484 .tuner_addr = ADDR_UNSET,
2485 .radio_addr = ADDR_UNSET,
2487 [BTTV_BOARD_SPIRIT_TV] = {
2488 /* Spirit TV Tuner from http://spiritmodems.com.au */
2489 /* Stafford Goodsell <surge@goliath.homeunix.org> */
2490 .name = "Spirit TV Tuner",
2495 .gpiomask = 0x0000000f,
2496 .muxsel = { 2, 1, 1 },
2497 .gpiomux = { 0x02, 0x00, 0x00, 0x00 },
2498 .tuner_type = TUNER_TEMIC_PAL,
2499 .tuner_addr = ADDR_UNSET,
2500 .radio_addr = ADDR_UNSET,
2504 [BTTV_BOARD_AVDVBT_771] = {
2505 /* Wolfram Joost <wojo@frokaschwei.de> */
2506 .name = "AVerMedia AVerTV DVB-T 771",
2510 .tuner_type = TUNER_ABSENT,
2511 .tuner_addr = ADDR_UNSET,
2512 .radio_addr = ADDR_UNSET,
2513 .muxsel = { 3 , 3 },
2522 /* ---- card 0x7c ---------------------------------- */
2523 [BTTV_BOARD_AVDVBT_761] = {
2524 /* Matt Jesson <dvb@jesson.eclipse.co.uk> */
2525 /* Based on the Nebula card data - added remote and new card number - BTTV_BOARD_AVDVBT_761, see also ir-kbd-gpio.c */
2526 .name = "AverMedia AverTV DVB-T 761",
2530 .muxsel = { 3, 1, 2, 0 }, /* Comp0, S-Video, ?, ? */
2535 .tuner_type = UNSET,
2536 .tuner_addr = ADDR_UNSET,
2537 .radio_addr = ADDR_UNSET,
2542 [BTTV_BOARD_MATRIX_VISIONSQ] = {
2543 /* andre.schwarz@matrix-vision.de */
2544 .name = "MATRIX Vision Sigma-SQ",
2550 .muxsel = { 2, 2, 2, 2, 2, 2, 2, 2,
2551 3, 3, 3, 3, 3, 3, 3, 3 },
2552 .muxsel_hook = sigmaSQ_muxsel,
2556 .tuner_type = UNSET,
2557 .tuner_addr = ADDR_UNSET,
2558 .radio_addr = ADDR_UNSET,
2560 [BTTV_BOARD_MATRIX_VISIONSLC] = {
2561 /* andre.schwarz@matrix-vision.de */
2562 .name = "MATRIX Vision Sigma-SLC",
2568 .muxsel = { 2, 2, 2, 2 },
2569 .muxsel_hook = sigmaSLC_muxsel,
2573 .tuner_type = UNSET,
2574 .tuner_addr = ADDR_UNSET,
2575 .radio_addr = ADDR_UNSET,
2577 /* BTTV_BOARD_APAC_VIEWCOMP */
2578 [BTTV_BOARD_APAC_VIEWCOMP] = {
2579 /* Attila Kondoros <attila.kondoros@chello.hu> */
2580 /* bt878 TV + FM 0x00000000 subsystem ID */
2581 .name = "APAC Viewcomp 878(AMAX)",
2587 .muxsel = { 2, 3, 1, 1 },
2588 .gpiomux = { 2, 0, 0, 0 },
2592 .tuner_type = TUNER_PHILIPS_PAL,
2593 .tuner_addr = ADDR_UNSET,
2594 .radio_addr = ADDR_UNSET,
2595 .has_remote = 1, /* miniremote works, see ir-kbd-gpio.c */
2596 .has_radio = 1, /* not every card has radio */
2599 /* ---- card 0x80 ---------------------------------- */
2600 [BTTV_BOARD_DVICO_DVBT_LITE] = {
2601 /* Chris Pascoe <c.pascoe@itee.uq.edu.au> */
2602 .name = "DViCO FusionHDTV DVB-T Lite",
2610 .tuner_type = UNSET,
2611 .tuner_addr = ADDR_UNSET,
2612 .radio_addr = ADDR_UNSET,
2614 [BTTV_BOARD_VGEAR_MYVCD] = {
2615 /* Steven <photon38@pchome.com.tw> */
2616 .name = "V-Gear MyVCD",
2622 .muxsel = {2, 3, 1, 0 },
2623 .gpiomux = {0x31, 0x31, 0x31, 0x31 },
2627 .tuner_type = TUNER_PHILIPS_NTSC_M,
2628 .tuner_addr = ADDR_UNSET,
2629 .radio_addr = ADDR_UNSET,
2632 [BTTV_BOARD_SUPER_TV] = {
2633 /* Rick C <cryptdragoon@gmail.com> */
2634 .name = "Super TV Tuner",
2639 .muxsel = { 2, 3, 1, 0 },
2640 .tuner_type = TUNER_PHILIPS_NTSC,
2641 .tuner_addr = ADDR_UNSET,
2642 .radio_addr = ADDR_UNSET,
2643 .gpiomask = 0x008007,
2644 .gpiomux = { 0, 0x000001,0,0 },
2648 [BTTV_BOARD_TIBET_CS16] = {
2649 /* Chris Fanning <video4linux@haydon.net> */
2650 .name = "Tibet Systems 'Progress DVR' CS16",
2655 .muxsel = { 2, 2, 2, 2, 2, 2, 2, 2, 2, 2, 2, 2, 2, 2, 2, 2 },
2660 .tuner_type = UNSET,
2661 .tuner_addr = ADDR_UNSET,
2662 .radio_addr = ADDR_UNSET,
2663 .muxsel_hook = tibetCS16_muxsel,
2665 [BTTV_BOARD_KODICOM_4400R] = {
2666 /* Bill Brack <wbrack@mmm.com.hk> */
2668 * Note that, because of the card's wiring, the "master"
2669 * BT878A chip (i.e. the one which controls the analog switch
2670 * and must use this card type) is the 2nd one detected. The
2671 * other 3 chips should use card type 0x85, whose description
2672 * follows this one. There is a EEPROM on the card (which is
2673 * connected to the I2C of one of those other chips), but is
2674 * not currently handled. There is also a facility for a
2675 * "monitor", which is also not currently implemented.
2677 .name = "Kodicom 4400R (master)",
2681 .tuner_type = UNSET,
2682 .tuner_addr = ADDR_UNSET,
2683 .radio_addr = ADDR_UNSET,
2685 /* GPIO bits 0-9 used for analog switch:
2686 * 00 - 03: camera selector
2687 * 04 - 06: channel (controller) selector
2688 * 07: data (1->on, 0->off)
2691 * bit 16 is input from sync separator for the channel
2693 .gpiomask = 0x0003ff,
2695 .muxsel = { 3, 3, 3, 3, 3, 3, 3, 3, 3, 3, 3, 3, 3, 3, 3, 3 },
2700 .muxsel_hook = kodicom4400r_muxsel,
2702 [BTTV_BOARD_KODICOM_4400R_SL] = {
2703 /* Bill Brack <wbrack@mmm.com.hk> */
2704 /* Note that, for reasons unknown, the "master" BT878A chip (i.e. the
2705 * one which controls the analog switch, and must use the card type)
2706 * is the 2nd one detected. The other 3 chips should use this card
2709 .name = "Kodicom 4400R (slave)",
2713 .tuner_type = UNSET,
2714 .tuner_addr = ADDR_UNSET,
2715 .radio_addr = ADDR_UNSET,
2717 .gpiomask = 0x010000,
2719 .muxsel = { 3, 3, 3, 3, 3, 3, 3, 3, 3, 3, 3, 3, 3, 3, 3, 3 },
2724 .muxsel_hook = kodicom4400r_muxsel,
2726 /* ---- card 0x86---------------------------------- */
2727 [BTTV_BOARD_ADLINK_RTV24] = {
2728 /* Michael Henson <mhenson@clarityvi.com> */
2729 /* Adlink RTV24 with special unlock codes */
2730 .name = "Adlink RTV24",
2735 .muxsel = { 2, 3, 1, 0 },
2736 .tuner_type = UNSET,
2737 .tuner_addr = ADDR_UNSET,
2738 .radio_addr = ADDR_UNSET,
2741 /* ---- card 0x87---------------------------------- */
2742 [BTTV_BOARD_DVICO_FUSIONHDTV_5_LITE] = {
2743 /* Michael Krufky <mkrufky@m1k.net> */
2744 .name = "DViCO FusionHDTV 5 Lite",
2746 .tuner_type = TUNER_LG_TDVS_H06XF, /* TDVS-H064F */
2747 .tuner_addr = ADDR_UNSET,
2748 .radio_addr = ADDR_UNSET,
2752 .muxsel = { 2, 3, 1 },
2753 .gpiomask = 0x00e00007,
2754 .gpiomux = { 0x00400005, 0, 0x00000001, 0 },
2755 .gpiomute = 0x00c00007,
2761 /* ---- card 0x88---------------------------------- */
2762 [BTTV_BOARD_ACORP_Y878F] = {
2763 /* Mauro Carvalho Chehab <mchehab@infradead.org> */
2764 .name = "Acorp Y878F",
2769 .gpiomask = 0x01fe00,
2770 .muxsel = { 2, 3, 1, 1 },
2771 .gpiomux = { 0x001e00, 0, 0x018000, 0x014000 },
2772 .gpiomute = 0x002000,
2775 .tuner_type = TUNER_YMEC_TVF66T5_B_DFF,
2776 .tuner_addr = 0xc1 >>1,
2777 .radio_addr = 0xc1 >>1,
2780 /* ---- card 0x89 ---------------------------------- */
2781 [BTTV_BOARD_CONCEPTRONIC_CTVFMI2] = {
2782 .name = "Conceptronic CTVFMi v2",
2787 .gpiomask = 0x001c0007,
2788 .muxsel = { 2, 3, 1, 1 },
2789 .gpiomux = { 0, 1, 2, 2 },
2793 .tuner_type = TUNER_TENA_9533_DI,
2794 .tuner_addr = ADDR_UNSET,
2795 .radio_addr = ADDR_UNSET,
2799 /* ---- card 0x8a ---------------------------------- */
2800 [BTTV_BOARD_PV_BT878P_2E] = {
2801 .name = "Prolink Pixelview PV-BT878P+ (Rev.2E)",
2806 .gpiomask = 0x01fe00,
2807 .muxsel = { 2,3,1,1,-1 },
2808 .digital_mode = DIGITAL_MODE_CAMERA,
2809 .gpiomux = { 0x00400, 0x10400, 0x04400, 0x80000 },
2810 .gpiomute = 0x12400,
2813 .tuner_type = TUNER_LG_PAL_FM,
2814 .tuner_addr = ADDR_UNSET,
2815 .radio_addr = ADDR_UNSET,
2818 /* ---- card 0x8b ---------------------------------- */
2819 [BTTV_BOARD_PV_M4900] = {
2820 /* Sérgio Fortier <sergiofortier@yahoo.com.br> */
2821 .name = "Prolink PixelView PlayTV MPEG2 PV-M4900",
2827 .muxsel = { 2, 3, 1, 1 },
2828 .gpiomux = { 0x21, 0x20, 0x24, 0x2c },
2832 .tuner_type = TUNER_YMEC_TVF_5533MF,
2833 .tuner_addr = ADDR_UNSET,
2834 .radio_addr = ADDR_UNSET,
2838 /* ---- card 0x8c ---------------------------------- */
2839 /* Has four Bt878 chips behind a PCI bridge, each chip has:
2840 one external BNC composite input (mux 2)
2841 three internal composite inputs (unknown muxes)
2842 an 18-bit stereo A/D (CS5331A), which has:
2843 one external stereo unblanced (RCA) audio connection
2844 one (or 3?) internal stereo balanced (XLR) audio connection
2845 input is selected via gpio to a 14052B mux
2846 (mask=0x300, unbal=0x000, bal=0x100, ??=0x200,0x300)
2847 gain is controlled via an X9221A chip on the I2C bus @0x28
2848 sample rate is controlled via gpio to an MK1413S
2849 (mask=0x3, 32kHz=0x0, 44.1kHz=0x1, 48kHz=0x2, ??=0x3)
2850 There is neither a tuner nor an svideo input. */
2851 [BTTV_BOARD_OSPREY440] = {
2852 .name = "Osprey 440",
2854 .audio_inputs = 2, /* this is meaningless */
2857 .muxsel = { 2, 3, 0, 1 }, /* 3,0,1 are guesses */
2859 .gpiomute = 0x000, /* int + 32kHz */
2860 .gpiomux = { 0, 0, 0x000, 0x100},
2862 .tuner_type = UNSET,
2863 .tuner_addr = ADDR_UNSET,
2864 .radio_addr = ADDR_UNSET,
2869 /* ---- card 0x8d ---------------------------------- */
2870 [BTTV_BOARD_ASOUND_SKYEYE] = {
2871 .name = "Asound Skyeye PCTV",
2877 .muxsel = { 2, 3, 1, 1 },
2878 .gpiomux = { 2, 0, 0, 0 },
2882 .tuner_type = TUNER_PHILIPS_NTSC,
2883 .tuner_addr = ADDR_UNSET,
2884 .radio_addr = ADDR_UNSET,
2886 /* ---- card 0x8e ---------------------------------- */
2887 [BTTV_BOARD_SABRENT_TVFM] = {
2888 .name = "Sabrent TV-FM (bttv version)",
2893 .gpiomask = 0x108007,
2894 .muxsel = { 2, 3, 1, 1 },
2895 .gpiomux = { 100000, 100002, 100002, 100000 },
2900 .tuner_type = TUNER_TNF_5335MF,
2901 .tuner_addr = ADDR_UNSET,
2904 /* ---- card 0x8f ---------------------------------- */
2905 [BTTV_BOARD_HAUPPAUGE_IMPACTVCB] = {
2906 .name = "Hauppauge ImpactVCB (bt878)",
2911 .gpiomask = 0x0f, /* old: 7 */
2912 .muxsel = { 0, 1, 3, 2 }, /* Composite 0-3 */
2916 .tuner_type = UNSET,
2917 .tuner_addr = ADDR_UNSET,
2918 .radio_addr = ADDR_UNSET,
2920 [BTTV_BOARD_MACHTV_MAGICTV] = {
2921 /* Julian Calaby <julian.calaby@gmail.com>
2922 * Slightly different from original MachTV definition (0x60)
2924 * FIXME: RegSpy says gpiomask should be "0x001c800f", but it
2925 * stuffs up remote chip. Bug is a pin on the jaecs is not set
2926 * properly (methinks) causing no keyup bits being set */
2928 .name = "MagicTV", /* rebranded MachTV */
2934 .muxsel = { 2, 3, 1, 1 },
2935 .gpiomux = { 0, 1, 2, 3 },
2937 .tuner_type = TUNER_TEMIC_4009FR5_PAL,
2938 .tuner_addr = ADDR_UNSET,
2939 .radio_addr = ADDR_UNSET,
2944 [BTTV_BOARD_SSAI_SECURITY] = {
2945 .name = "SSAI Security Video Interface",
2950 .muxsel = { 0, 1, 2, 3 },
2951 .tuner_type = UNSET,
2952 .tuner_addr = ADDR_UNSET,
2953 .radio_addr = ADDR_UNSET,
2955 [BTTV_BOARD_SSAI_ULTRASOUND] = {
2956 .name = "SSAI Ultrasound Video Interface",
2961 .muxsel = { 2, 0, 1, 3 },
2962 .tuner_type = UNSET,
2963 .tuner_addr = ADDR_UNSET,
2964 .radio_addr = ADDR_UNSET,
2966 /* ---- card 0x94---------------------------------- */
2967 [BTTV_BOARD_DVICO_FUSIONHDTV_2] = {
2968 .name = "DViCO FusionHDTV 2",
2970 .tuner_type = TUNER_PHILIPS_FCV1236D,
2971 .tuner_addr = ADDR_UNSET,
2972 .radio_addr = ADDR_UNSET,
2976 .muxsel = { 2, 3, 1 },
2977 .gpiomask = 0x00e00007,
2978 .gpiomux = { 0x00400005, 0, 0x00000001, 0 },
2979 .gpiomute = 0x00c00007,
2984 /* ---- card 0x95---------------------------------- */
2985 [BTTV_BOARD_TYPHOON_TVTUNERPCI] = {
2986 .name = "Typhoon TV-Tuner PCI (50684)",
2991 .gpiomask = 0x3014f,
2992 .muxsel = { 2, 3, 1, 1 },
2993 .gpiomux = { 0x20001,0x10001, 0, 0 },
2997 .tuner_type = TUNER_PHILIPS_PAL_I,
2998 .tuner_addr = ADDR_UNSET,
2999 .radio_addr = ADDR_UNSET,
3001 [BTTV_BOARD_GEOVISION_GV600] = {
3003 .name = "Geovision GV-600",
3009 .muxsel = { 2, 2, 2, 2, 2, 2, 2, 2,
3010 2, 2, 2, 2, 2, 2, 2, 2 },
3011 .muxsel_hook = geovision_muxsel,
3015 .tuner_type = UNSET,
3016 .tuner_addr = ADDR_UNSET,
3017 .radio_addr = ADDR_UNSET,
3019 [BTTV_BOARD_KOZUMI_KTV_01C] = {
3020 /* Mauro Lacy <mauro@lacy.com.ar>
3021 * Based on MagicTV and Conceptronic CONTVFMi */
3023 .name = "Kozumi KTV-01C",
3028 .gpiomask = 0x008007,
3029 .muxsel = { 2, 3, 1, 1 },
3030 .gpiomux = { 0, 1, 2, 2 }, /* CONTVFMi */
3031 .gpiomute = 3, /* CONTVFMi */
3033 .tuner_type = TUNER_PHILIPS_FM1216ME_MK3, /* TCL MK3 */
3034 .tuner_addr = ADDR_UNSET,
3035 .radio_addr = ADDR_UNSET,
3042 static const unsigned int bttv_num_tvcards = ARRAY_SIZE(bttv_tvcards);
3044 /* ----------------------------------------------------------------------- */
3046 static unsigned char eeprom_data[256];
3051 void __devinit bttv_idcard(struct bttv *btv)
3053 unsigned int gpiobits;
3057 /* read PCI subsystem ID */
3058 pci_read_config_word(btv->c.pci, PCI_SUBSYSTEM_ID, &tmp);
3059 btv->cardid = tmp << 16;
3060 pci_read_config_word(btv->c.pci, PCI_SUBSYSTEM_VENDOR_ID, &tmp);
3063 if (0 != btv->cardid && 0xffffffff != btv->cardid) {
3064 /* look for the card */
3065 for (type = -1, i = 0; cards[i].id != 0; i++)
3066 if (cards[i].id == btv->cardid)
3071 printk(KERN_INFO "bttv%d: detected: %s [card=%d], "
3072 "PCI subsystem ID is %04x:%04x\n",
3073 btv->c.nr,cards[type].name,cards[type].cardnr,
3074 btv->cardid & 0xffff,
3075 (btv->cardid >> 16) & 0xffff);
3076 btv->c.type = cards[type].cardnr;
3079 printk(KERN_INFO "bttv%d: subsystem: %04x:%04x (UNKNOWN)\n",
3080 btv->c.nr, btv->cardid & 0xffff,
3081 (btv->cardid >> 16) & 0xffff);
3082 printk(KERN_DEBUG "please mail id, board name and "
3083 "the correct card= insmod option to video4linux-list@redhat.com\n");
3087 /* let the user override the autodetected type */
3088 if (card[btv->c.nr] < bttv_num_tvcards)
3089 btv->c.type=card[btv->c.nr];
3091 /* print which card config we are using */
3092 printk(KERN_INFO "bttv%d: using: %s [card=%d,%s]\n",btv->c.nr,
3093 bttv_tvcards[btv->c.type].name, btv->c.type,
3094 card[btv->c.nr] < bttv_num_tvcards
3095 ? "insmod option" : "autodetected");
3097 /* overwrite gpio stuff ?? */
3098 if (UNSET == audioall && UNSET == audiomux[0])
3101 if (UNSET != audiomux[0]) {
3103 for (i = 0; i < ARRAY_SIZE(bttv_tvcards->gpiomux); i++) {
3104 bttv_tvcards[btv->c.type].gpiomux[i] = audiomux[i];
3105 gpiobits |= audiomux[i];
3108 gpiobits = audioall;
3109 for (i = 0; i < ARRAY_SIZE(bttv_tvcards->gpiomux); i++) {
3110 bttv_tvcards[btv->c.type].gpiomux[i] = audioall;
3113 bttv_tvcards[btv->c.type].gpiomask = (UNSET != gpiomask) ? gpiomask : gpiobits;
3114 printk(KERN_INFO "bttv%d: gpio config override: mask=0x%x, mux=",
3115 btv->c.nr,bttv_tvcards[btv->c.type].gpiomask);
3116 for (i = 0; i < ARRAY_SIZE(bttv_tvcards->gpiomux); i++) {
3117 printk("%s0x%x", i ? "," : "", bttv_tvcards[btv->c.type].gpiomux[i]);
3123 * (most) board specific initialisations goes here
3126 /* Some Modular Technology cards have an eeprom, but no subsystem ID */
3127 static void identify_by_eeprom(struct bttv *btv, unsigned char eeprom_data[256])
3131 if (0 == strncmp(eeprom_data,"GET MM20xPCTV",13))
3132 type = BTTV_BOARD_MODTEC_205;
3133 else if (0 == strncmp(eeprom_data+20,"Picolo",7))
3134 type = BTTV_BOARD_EURESYS_PICOLO;
3135 else if (eeprom_data[0] == 0x84 && eeprom_data[2]== 0)
3136 type = BTTV_BOARD_HAUPPAUGE; /* old bt848 */
3140 printk("bttv%d: detected by eeprom: %s [card=%d]\n",
3141 btv->c.nr, bttv_tvcards[btv->c.type].name, btv->c.type);
3145 static void flyvideo_gpio(struct bttv *btv)
3147 int gpio,has_remote,has_radio,is_capture_only,is_lr90,has_tda9820_tda9821;
3148 int tuner=UNSET,ttype;
3150 gpio_inout(0xffffff, 0);
3151 udelay(8); /* without this we would see the 0x1800 mask */
3153 /* FIXME: must restore OUR_EN ??? */
3155 /* all cards provide GPIO info, some have an additional eeprom
3156 * LR50: GPIO coding can be found lower right CP1 .. CP9
3157 * CP9=GPIO23 .. CP1=GPIO15; when OPEN, the corresponding GPIO reads 1.
3159 * LR90: GP9=GPIO23 .. GP1=GPIO15 (right above the bt878)
3161 * lowest 3 bytes are remote control codes (no handshake needed)
3162 * xxxFFF: No remote control chip soldered
3163 * xxxF00(LR26/LR50), xxxFE0(LR90): Remote control chip (LVA001 or CF45) soldered
3164 * Note: Some bits are Audio_Mask !
3166 ttype=(gpio&0x0f0000)>>16;
3168 case 0x0: tuner=2; /* NTSC, e.g. TPI8NSR11P */
3170 case 0x2: tuner=39;/* LG NTSC (newer TAPC series) TAPC-H701P */
3172 case 0x4: tuner=5; /* Philips PAL TPI8PSB02P, TPI8PSB12P, TPI8PSB12D or FI1216, FM1216 */
3174 case 0x6: tuner=37;/* LG PAL (newer TAPC series) TAPC-G702P */
3176 case 0xC: tuner=3; /* Philips SECAM(+PAL) FQ1216ME or FI1216MF */
3179 printk(KERN_INFO "bttv%d: FlyVideo_gpio: unknown tuner type.\n", btv->c.nr);
3182 has_remote = gpio & 0x800000;
3183 has_radio = gpio & 0x400000;
3184 /* unknown 0x200000;
3185 * unknown2 0x100000; */
3186 is_capture_only = !(gpio & 0x008000); /* GPIO15 */
3187 has_tda9820_tda9821 = !(gpio & 0x004000);
3188 is_lr90 = !(gpio & 0x002000); /* else LR26/LR50 (LR38/LR51 f. capture only) */
3190 * gpio & 0x001000 output bit for audio routing */
3193 tuner = TUNER_ABSENT; /* No tuner present */
3195 printk(KERN_INFO "bttv%d: FlyVideo Radio=%s RemoteControl=%s Tuner=%d gpio=0x%06x\n",
3196 btv->c.nr, has_radio? "yes":"no ", has_remote? "yes":"no ", tuner, gpio);
3197 printk(KERN_INFO "bttv%d: FlyVideo LR90=%s tda9821/tda9820=%s capture_only=%s\n",
3198 btv->c.nr, is_lr90?"yes":"no ", has_tda9820_tda9821?"yes":"no ",
3199 is_capture_only?"yes":"no ");
3201 if (tuner != UNSET) /* only set if known tuner autodetected, else let insmod option through */
3202 btv->tuner_type = tuner;
3203 btv->has_radio = has_radio;
3205 /* LR90 Audio Routing is done by 2 hef4052, so Audio_Mask has 4 bits: 0x001c80
3206 * LR26/LR50 only has 1 hef4052, Audio_Mask 0x000c00
3207 * Audio options: from tuner, from tda9821/tda9821(mono,stereo,sap), from tda9874, ext., mute */
3208 if(has_tda9820_tda9821) btv->audio_mode_gpio = lt9415_audio;
3209 /* todo: if(has_tda9874) btv->audio_mode_gpio = fv2000s_audio; */
3212 static int miro_tunermap[] = { 0,6,2,3, 4,5,6,0, 3,0,4,5, 5,2,16,1,
3213 14,2,17,1, 4,1,4,3, 1,2,16,1, 4,4,4,4 };
3214 static int miro_fmtuner[] = { 0,0,0,0, 0,0,0,0, 0,0,0,0, 0,0,0,1,
3215 1,1,1,1, 1,1,1,0, 0,0,0,0, 0,1,0,0 };
3217 static void miro_pinnacle_gpio(struct bttv *btv)
3222 gpio_inout(0xffffff, 0);
3224 id = ((gpio>>10) & 63) -1;
3225 msp = bttv_I2CRead(btv, I2C_ADDR_MSP3400, "MSP34xx");
3227 btv->tuner_type = miro_tunermap[id];
3228 if (0 == (gpio & 0x20)) {
3230 if (!miro_fmtuner[id]) {
3231 btv->has_matchbox = 1;
3232 btv->mbox_we = (1<<6);
3233 btv->mbox_most = (1<<7);
3234 btv->mbox_clk = (1<<8);
3235 btv->mbox_data = (1<<9);
3236 btv->mbox_mask = (1<<6)|(1<<7)|(1<<8)|(1<<9);
3242 if (btv->c.type == BTTV_BOARD_MIRO)
3243 btv->c.type = BTTV_BOARD_MIROPRO;
3244 if (btv->c.type == BTTV_BOARD_PINNACLE)
3245 btv->c.type = BTTV_BOARD_PINNACLEPRO;
3248 "bttv%d: miro: id=%d tuner=%d radio=%s stereo=%s\n",
3249 btv->c.nr, id+1, btv->tuner_type,
3250 !btv->has_radio ? "no" :
3251 (btv->has_matchbox ? "matchbox" : "fmtuner"),
3252 (-1 == msp) ? "no" : "yes");
3254 /* new cards with microtune tuner */
3259 info = "PAL / mono";
3260 btv->tda9887_conf = TDA9887_INTERCARRIER;
3263 info = "PAL+SECAM / stereo";
3265 btv->tda9887_conf = TDA9887_QSS;
3268 info = "NTSC / stereo";
3270 btv->tda9887_conf = TDA9887_QSS;
3273 info = "PAL+SECAM / mono";
3274 btv->tda9887_conf = TDA9887_QSS;
3277 info = "NTSC / mono";
3278 btv->tda9887_conf = TDA9887_INTERCARRIER;
3281 info = "NTSC / stereo";
3282 btv->tda9887_conf = TDA9887_INTERCARRIER;
3285 info = "PAL / stereo";
3286 btv->tda9887_conf = TDA9887_INTERCARRIER;
3289 info = "oops: unknown card";
3293 btv->c.type = BTTV_BOARD_PINNACLEPRO;
3295 "bttv%d: pinnacle/mt: id=%d info=\"%s\" radio=%s\n",
3296 btv->c.nr, id, info, btv->has_radio ? "yes" : "no");
3297 btv->tuner_type = TUNER_MT2032;
3301 /* GPIO21 L: Buffer aktiv, H: Buffer inaktiv */
3302 #define LM1882_SYNC_DRIVE 0x200000L
3304 static void init_ids_eagle(struct bttv *btv)
3306 gpio_inout(0xffffff,0xFFFF37);
3307 gpio_write(0x200020);
3309 /* flash strobe inverter ?! */
3310 gpio_write(0x200024);
3312 /* switch sync drive off */
3313 gpio_bits(LM1882_SYNC_DRIVE,LM1882_SYNC_DRIVE);
3315 /* set BT848 muxel to 2 */
3316 btaor((2)<<5, ~(2<<5), BT848_IFORM);
3319 /* Muxsel helper for the IDS Eagle.
3320 * the eagles does not use the standard muxsel-bits but
3321 * has its own multiplexer */
3322 static void eagle_muxsel(struct bttv *btv, unsigned int input)
3324 btaor((2)<<5, ~(3<<5), BT848_IFORM);
3325 gpio_bits(3,bttv_tvcards[btv->c.type].muxsel[input&7]);
3328 /* set chroma ADC to sleep */
3329 btor(BT848_ADC_C_SLEEP, BT848_ADC);
3330 /* set to composite video */
3331 btand(~BT848_CONTROL_COMP, BT848_E_CONTROL);
3332 btand(~BT848_CONTROL_COMP, BT848_O_CONTROL);
3334 /* switch sync drive off */
3335 gpio_bits(LM1882_SYNC_DRIVE,LM1882_SYNC_DRIVE);
3338 static void gvc1100_muxsel(struct bttv *btv, unsigned int input)
3340 static const int masks[] = {0x30, 0x01, 0x12, 0x23};
3341 gpio_write(masks[input%4]);
3344 /* LMLBT4x initialization - to allow access to GPIO bits for sensors input and
3347 GPIObit | 10 | 9 | 8 | 7 | 6 | 5 | 4 | 3 | 2 | 1 | 0 |
3348 assignment | TI | O3|INx| O2| O1|IN4|IN3|IN2|IN1| | |
3350 IN - sensor inputs, INx - sensor inputs and TI XORed together
3351 O1,O2,O3 - alarm outputs (relays)
3353 OUT ENABLE 1 1 0 . 1 1 0 0 . 0 0 0 0 = 0x6C0
3357 static void init_lmlbt4x(struct bttv *btv)
3359 printk(KERN_DEBUG "LMLBT4x init\n");
3360 btwrite(0x000000, BT848_GPIO_REG_INP);
3361 gpio_inout(0xffffff, 0x0006C0);
3362 gpio_write(0x000000);
3365 static void sigmaSQ_muxsel(struct bttv *btv, unsigned int input)
3367 unsigned int inmux = input % 8;
3368 gpio_inout( 0xf, 0xf );
3369 gpio_bits( 0xf, inmux );
3372 static void sigmaSLC_muxsel(struct bttv *btv, unsigned int input)
3374 unsigned int inmux = input % 4;
3375 gpio_inout( 3<<9, 3<<9 );
3376 gpio_bits( 3<<9, inmux<<9 );
3379 static void geovision_muxsel(struct bttv *btv, unsigned int input)
3381 unsigned int inmux = input % 16;
3382 gpio_inout(0xf, 0xf);
3383 gpio_bits(0xf, inmux);
3386 /* ----------------------------------------------------------------------- */
3388 static void bttv_reset_audio(struct bttv *btv)
3391 * BT878A has a audio-reset register.
3392 * 1. This register is an audio reset function but it is in
3393 * function-0 (video capture) address space.
3394 * 2. It is enough to do this once per power-up of the card.
3395 * 3. There is a typo in the Conexant doc -- it is not at
3396 * 0x5B, but at 0x058. (B is an odd-number, obviously a typo!).
3397 * --//Shrikumar 030609
3403 printk("bttv%d: BT878A ARESET\n",btv->c.nr);
3404 btwrite((1<<7), 0x058);
3409 /* initialization part one -- before registering i2c bus */
3410 void __devinit bttv_init_card1(struct bttv *btv)
3412 switch (btv->c.type) {
3413 case BTTV_BOARD_HAUPPAUGE:
3414 case BTTV_BOARD_HAUPPAUGE878:
3415 boot_msp34xx(btv,5);
3417 case BTTV_BOARD_VOODOOTV_200:
3418 case BTTV_BOARD_VOODOOTV_FM:
3419 boot_msp34xx(btv,20);
3421 case BTTV_BOARD_AVERMEDIA98:
3422 boot_msp34xx(btv,11);
3424 case BTTV_BOARD_HAUPPAUGEPVR:
3427 case BTTV_BOARD_TWINHAN_DST:
3428 case BTTV_BOARD_AVDVBT_771:
3429 case BTTV_BOARD_PINNACLESAT:
3430 btv->use_i2c_hw = 1;
3432 case BTTV_BOARD_ADLINK_RTV24:
3437 if (!bttv_tvcards[btv->c.type].has_dvb)
3438 bttv_reset_audio(btv);
3441 /* initialization part two -- after registering i2c bus */
3442 void __devinit bttv_init_card2(struct bttv *btv)
3444 int addr=ADDR_UNSET;
3446 btv->tuner_type = UNSET;
3448 if (BTTV_BOARD_UNKNOWN == btv->c.type) {
3449 bttv_readee(btv,eeprom_data,0xa0);
3450 identify_by_eeprom(btv,eeprom_data);
3453 switch (btv->c.type) {
3454 case BTTV_BOARD_MIRO:
3455 case BTTV_BOARD_MIROPRO:
3456 case BTTV_BOARD_PINNACLE:
3457 case BTTV_BOARD_PINNACLEPRO:
3459 miro_pinnacle_gpio(btv);
3461 case BTTV_BOARD_FLYVIDEO_98:
3462 case BTTV_BOARD_MAXI:
3463 case BTTV_BOARD_LIFE_FLYKIT:
3464 case BTTV_BOARD_FLYVIDEO:
3465 case BTTV_BOARD_TYPHOON_TVIEW:
3466 case BTTV_BOARD_CHRONOS_VS2:
3467 case BTTV_BOARD_FLYVIDEO_98FM:
3468 case BTTV_BOARD_FLYVIDEO2000:
3469 case BTTV_BOARD_FLYVIDEO98EZ:
3470 case BTTV_BOARD_CONFERENCETV:
3471 case BTTV_BOARD_LIFETEC_9415:
3474 case BTTV_BOARD_HAUPPAUGE:
3475 case BTTV_BOARD_HAUPPAUGE878:
3476 case BTTV_BOARD_HAUPPAUGEPVR:
3477 /* pick up some config infos from the eeprom */
3478 bttv_readee(btv,eeprom_data,0xa0);
3479 hauppauge_eeprom(btv);
3481 case BTTV_BOARD_AVERMEDIA98:
3482 case BTTV_BOARD_AVPHONE98:
3483 bttv_readee(btv,eeprom_data,0xa0);
3484 avermedia_eeprom(btv);
3486 case BTTV_BOARD_PXC200:
3489 case BTTV_BOARD_PICOLO_TETRA_CHIP:
3490 picolo_tetra_init(btv);
3492 case BTTV_BOARD_VHX:
3494 btv->has_matchbox = 1;
3495 btv->mbox_we = 0x20;
3497 btv->mbox_clk = 0x08;
3498 btv->mbox_data = 0x10;
3499 btv->mbox_mask = 0x38;
3501 case BTTV_BOARD_VOBIS_BOOSTAR:
3502 case BTTV_BOARD_TERRATV:
3503 terratec_active_radio_upgrade(btv);
3505 case BTTV_BOARD_MAGICTVIEW061:
3506 if (btv->cardid == 0x3002144f) {
3508 printk("bttv%d: radio detected by subsystem id (CPH05x)\n",btv->c.nr);
3511 case BTTV_BOARD_STB2:
3512 if (btv->cardid == 0x3060121a) {
3513 /* Fix up entry for 3DFX VoodooTV 100,
3514 which is an OEM STB card variant. */
3516 btv->tuner_type=TUNER_TEMIC_NTSC;
3519 case BTTV_BOARD_OSPREY1x0:
3520 case BTTV_BOARD_OSPREY1x0_848:
3521 case BTTV_BOARD_OSPREY101_848:
3522 case BTTV_BOARD_OSPREY1x1:
3523 case BTTV_BOARD_OSPREY1x1_SVID:
3524 case BTTV_BOARD_OSPREY2xx:
3525 case BTTV_BOARD_OSPREY2x0_SVID:
3526 case BTTV_BOARD_OSPREY2x0:
3527 case BTTV_BOARD_OSPREY440:
3528 case BTTV_BOARD_OSPREY500:
3529 case BTTV_BOARD_OSPREY540:
3530 case BTTV_BOARD_OSPREY2000:
3531 bttv_readee(btv,eeprom_data,0xa0);
3532 osprey_eeprom(btv, eeprom_data);
3534 case BTTV_BOARD_IDS_EAGLE:
3535 init_ids_eagle(btv);
3537 case BTTV_BOARD_MODTEC_205:
3538 bttv_readee(btv,eeprom_data,0xa0);
3541 case BTTV_BOARD_LMLBT4:
3544 case BTTV_BOARD_TIBET_CS16:
3545 tibetCS16_init(btv);
3547 case BTTV_BOARD_KODICOM_4400R:
3548 kodicom4400r_init(btv);
3552 /* pll configuration */
3553 if (!(btv->id==848 && btv->revision==0x11)) {
3554 /* defaults from card list */
3555 if (PLL_28 == bttv_tvcards[btv->c.type].pll) {
3556 btv->pll.pll_ifreq=28636363;
3557 btv->pll.pll_crystal=BT848_IFORM_XT0;
3559 if (PLL_35 == bttv_tvcards[btv->c.type].pll) {
3560 btv->pll.pll_ifreq=35468950;
3561 btv->pll.pll_crystal=BT848_IFORM_XT1;
3563 /* insmod options can override */
3564 switch (pll[btv->c.nr]) {
3566 btv->pll.pll_crystal = 0;
3567 btv->pll.pll_ifreq = 0;
3568 btv->pll.pll_ofreq = 0;
3570 case 1: /* 28 MHz */
3572 btv->pll.pll_ifreq = 28636363;
3573 btv->pll.pll_ofreq = 0;
3574 btv->pll.pll_crystal = BT848_IFORM_XT0;
3576 case 2: /* 35 MHz */
3578 btv->pll.pll_ifreq = 35468950;
3579 btv->pll.pll_ofreq = 0;
3580 btv->pll.pll_crystal = BT848_IFORM_XT1;
3584 btv->pll.pll_current = -1;
3586 /* tuner configuration (from card list / autodetect / insmod option) */
3587 if (ADDR_UNSET != bttv_tvcards[btv->c.type].tuner_addr)
3588 addr = bttv_tvcards[btv->c.type].tuner_addr;
3590 if (UNSET != bttv_tvcards[btv->c.type].tuner_type)
3591 if(UNSET == btv->tuner_type)
3592 btv->tuner_type = bttv_tvcards[btv->c.type].tuner_type;
3593 if (UNSET != tuner[btv->c.nr])
3594 btv->tuner_type = tuner[btv->c.nr];
3596 if (btv->tuner_type == TUNER_ABSENT ||
3597 bttv_tvcards[btv->c.type].tuner == UNSET)
3598 printk(KERN_INFO "bttv%d: tuner absent\n", btv->c.nr);
3599 else if(btv->tuner_type == UNSET)
3600 printk(KERN_WARNING "bttv%d: tuner type unset\n", btv->c.nr);
3602 printk(KERN_INFO "bttv%d: tuner type=%d\n", btv->c.nr,
3605 if (btv->tuner_type != UNSET) {
3606 struct tuner_setup tun_setup;
3608 tun_setup.mode_mask = T_ANALOG_TV | T_DIGITAL_TV;
3609 tun_setup.type = btv->tuner_type;
3610 tun_setup.addr = addr;
3612 bttv_call_i2c_clients(btv, TUNER_SET_TYPE_ADDR, &tun_setup);
3615 if (btv->tda9887_conf) {
3616 struct v4l2_priv_tun_config tda9887_cfg;
3618 tda9887_cfg.tuner = TUNER_TDA9887;
3619 tda9887_cfg.priv = &btv->tda9887_conf;
3621 bttv_call_i2c_clients(btv, TUNER_SET_CONFIG, &tda9887_cfg);
3624 btv->svhs = bttv_tvcards[btv->c.type].svhs;
3625 if (svhs[btv->c.nr] != UNSET)
3626 btv->svhs = svhs[btv->c.nr];
3627 if (remote[btv->c.nr] != UNSET)
3628 btv->has_remote = remote[btv->c.nr];
3630 if (bttv_tvcards[btv->c.type].has_radio)
3632 if (bttv_tvcards[btv->c.type].has_remote)
3634 if (!bttv_tvcards[btv->c.type].no_gpioirq)
3636 if (bttv_tvcards[btv->c.type].volume_gpio)
3637 btv->volume_gpio=bttv_tvcards[btv->c.type].volume_gpio;
3638 if (bttv_tvcards[btv->c.type].audio_mode_gpio)
3639 btv->audio_mode_gpio=bttv_tvcards[btv->c.type].audio_mode_gpio;
3641 if (bttv_tvcards[btv->c.type].digital_mode == DIGITAL_MODE_CAMERA) {
3642 /* detect Bt832 chip for quartzsight digital camera */
3643 if ((bttv_I2CRead(btv, I2C_ADDR_BT832_ALT1, "Bt832") >=0) ||
3644 (bttv_I2CRead(btv, I2C_ADDR_BT832_ALT2, "Bt832") >=0))
3651 if (bttv_tvcards[btv->c.type].tuner == UNSET)
3652 return; /* no tuner or related drivers to load */
3654 /* try to detect audio/fader chips */
3655 if (!bttv_tvcards[btv->c.type].no_msp34xx &&
3656 bttv_I2CRead(btv, I2C_ADDR_MSP3400, "MSP34xx") >=0)
3657 request_module("msp3400");
3659 if (bttv_tvcards[btv->c.type].msp34xx_alt &&
3660 bttv_I2CRead(btv, I2C_ADDR_MSP3400_ALT, "MSP34xx (alternate address)") >=0)
3661 request_module("msp3400");
3663 if (!bttv_tvcards[btv->c.type].no_tda9875 &&
3664 bttv_I2CRead(btv, I2C_ADDR_TDA9875, "TDA9875") >=0)
3665 request_module("tda9875");
3667 if (!bttv_tvcards[btv->c.type].no_tda7432 &&
3668 bttv_I2CRead(btv, I2C_ADDR_TDA7432, "TDA7432") >=0)
3669 request_module("tda7432");
3671 if (bttv_tvcards[btv->c.type].needs_tvaudio)
3672 request_module("tvaudio");
3674 if (btv->tuner_type != UNSET && btv->tuner_type != TUNER_ABSENT)
3675 request_module("tuner");
3679 /* ----------------------------------------------------------------------- */
3681 static void modtec_eeprom(struct bttv *btv)
3683 if( strncmp(&(eeprom_data[0x1e]),"Temic 4066 FY5",14) ==0) {
3684 btv->tuner_type=TUNER_TEMIC_4066FY5_PAL_I;
3685 printk("bttv%d: Modtec: Tuner autodetected by eeprom: %s\n",
3686 btv->c.nr,&eeprom_data[0x1e]);
3687 } else if (strncmp(&(eeprom_data[0x1e]),"Alps TSBB5",10) ==0) {
3688 btv->tuner_type=TUNER_ALPS_TSBB5_PAL_I;
3689 printk("bttv%d: Modtec: Tuner autodetected by eeprom: %s\n",
3690 btv->c.nr,&eeprom_data[0x1e]);
3691 } else if (strncmp(&(eeprom_data[0x1e]),"Philips FM1246",14) ==0) {
3692 btv->tuner_type=TUNER_PHILIPS_NTSC;
3693 printk("bttv%d: Modtec: Tuner autodetected by eeprom: %s\n",
3694 btv->c.nr,&eeprom_data[0x1e]);
3696 printk("bttv%d: Modtec: Unknown TunerString: %s\n",
3697 btv->c.nr,&eeprom_data[0x1e]);
3701 static void __devinit hauppauge_eeprom(struct bttv *btv)
3705 tveeprom_hauppauge_analog(&btv->i2c_client, &tv, eeprom_data);
3706 btv->tuner_type = tv.tuner_type;
3707 btv->has_radio = tv.has_radio;
3709 printk("bttv%d: Hauppauge eeprom indicates model#%d\n",
3710 btv->c.nr, tv.model);
3713 * Some of the 878 boards have duplicate PCI IDs. Switch the board
3714 * type based on model #.
3716 if(tv.model == 64900) {
3717 printk("bttv%d: Switching board type from %s to %s\n",
3719 bttv_tvcards[btv->c.type].name,
3720 bttv_tvcards[BTTV_BOARD_HAUPPAUGE_IMPACTVCB].name);
3721 btv->c.type = BTTV_BOARD_HAUPPAUGE_IMPACTVCB;
3725 static int terratec_active_radio_upgrade(struct bttv *btv)
3730 btv->has_matchbox = 1;
3731 btv->mbox_we = 0x10;
3732 btv->mbox_most = 0x20;
3733 btv->mbox_clk = 0x08;
3734 btv->mbox_data = 0x04;
3735 btv->mbox_mask = 0x3c;
3737 btv->mbox_iow = 1 << 8;
3738 btv->mbox_ior = 1 << 9;
3739 btv->mbox_csel = 1 << 10;
3742 tea5757_write(btv, 5 * freq + 0x358); /* write 0x1ed8 */
3743 if (0x1ed8 == tea5757_read(btv)) {
3744 printk("bttv%d: Terratec Active Radio Upgrade found.\n",
3747 btv->has_matchbox = 1;
3750 btv->has_matchbox = 0;
3756 /* ----------------------------------------------------------------------- */
3759 * minimal bootstrap for the WinTV/PVR -- upload altera firmware.
3761 * The hcwamc.rbf firmware file is on the Hauppauge driver CD. Have
3762 * a look at Pvr/pvr45xxx.EXE (self-extracting zip archive, can be
3763 * unpacked with unzip).
3765 #define PVR_GPIO_DELAY 10
3767 #define BTTV_ALT_DATA 0x000001
3768 #define BTTV_ALT_DCLK 0x100000
3769 #define BTTV_ALT_NCONFIG 0x800000
3771 static int __devinit pvr_altera_load(struct bttv *btv, u8 *micro, u32 microlen)
3777 gpio_inout(0xffffff,BTTV_ALT_DATA|BTTV_ALT_DCLK|BTTV_ALT_NCONFIG);
3779 udelay(PVR_GPIO_DELAY);
3781 gpio_write(BTTV_ALT_NCONFIG);
3782 udelay(PVR_GPIO_DELAY);
3784 for (n = 0; n < microlen; n++) {
3786 for (i = 0 ; i < 8 ; i++) {
3787 gpio_bits(BTTV_ALT_DCLK,0);
3789 gpio_bits(BTTV_ALT_DATA,BTTV_ALT_DATA);
3791 gpio_bits(BTTV_ALT_DATA,0);
3792 gpio_bits(BTTV_ALT_DCLK,BTTV_ALT_DCLK);
3796 gpio_bits(BTTV_ALT_DCLK,0);
3797 udelay(PVR_GPIO_DELAY);
3799 /* begin Altera init loop (Not necessary,but doesn't hurt) */
3800 for (i = 0 ; i < 30 ; i++) {
3801 gpio_bits(BTTV_ALT_DCLK,0);
3802 gpio_bits(BTTV_ALT_DCLK,BTTV_ALT_DCLK);
3804 gpio_bits(BTTV_ALT_DCLK,0);
3808 static int __devinit pvr_boot(struct bttv *btv)
3810 const struct firmware *fw_entry;
3813 rc = request_firmware(&fw_entry, "hcwamc.rbf", &btv->c.pci->dev);
3815 printk(KERN_WARNING "bttv%d: no altera firmware [via hotplug]\n",
3819 rc = pvr_altera_load(btv, fw_entry->data, fw_entry->size);
3820 printk(KERN_INFO "bttv%d: altera firmware upload %s\n",
3821 btv->c.nr, (rc < 0) ? "failed" : "ok");
3822 release_firmware(fw_entry);
3826 /* ----------------------------------------------------------------------- */
3827 /* some osprey specific stuff */
3829 static void __devinit osprey_eeprom(struct bttv *btv, const u8 ee[256])
3835 /* This code will nevery actually get called in this case.... */
3836 if (btv->c.type == BTTV_BOARD_UNKNOWN) {
3837 /* this might be an antique... check for MMAC label in eeprom */
3838 if (!strncmp(ee, "MMAC", 4)) {
3840 for (i = 0; i < 21; i++)
3842 if (checksum != ee[21])
3844 cardid = BTTV_BOARD_OSPREY1x0_848;
3845 for (i = 12; i < 21; i++)
3846 serial *= 10, serial += ee[i] - '0';
3849 unsigned short type;
3851 for (i = 4*16; i < 8*16; i += 16) {
3852 u16 checksum = ip_compute_csum(ee + i, 16);
3854 if ((checksum&0xff) + (checksum>>8) == 0xff)
3861 /* found a valid descriptor */
3862 type = get_unaligned_be16((__be16 *)(ee+4));
3867 cardid = BTTV_BOARD_OSPREY1x0_848;
3870 cardid = BTTV_BOARD_OSPREY101_848;
3876 cardid = BTTV_BOARD_OSPREY1x0;
3880 cardid = BTTV_BOARD_OSPREY1x1;
3885 cardid = BTTV_BOARD_OSPREY1x1_SVID;
3891 cardid = BTTV_BOARD_OSPREY2xx;
3895 cardid = BTTV_BOARD_OSPREY2x0_SVID;
3898 cardid = BTTV_BOARD_OSPREY500;
3902 cardid = BTTV_BOARD_OSPREY540;
3903 /* bttv_osprey_540_init(btv); */
3908 cardid = BTTV_BOARD_OSPREY2x0;
3909 /* enable output on select control lines */
3910 gpio_inout(0xffffff,0x000303);
3913 cardid = BTTV_BOARD_OSPREY440;
3916 /* unknown...leave generic, but get serial # */
3917 printk(KERN_INFO "bttv%d: "
3918 "osprey eeprom: unknown card type 0x%04x\n",
3922 serial = get_unaligned_be32((__be32 *)(ee+6));
3925 printk(KERN_INFO "bttv%d: osprey eeprom: card=%d '%s' serial=%u\n",
3927 cardid>0 ? bttv_tvcards[cardid].name : "Unknown", serial);
3929 if (cardid<0 || btv->c.type == cardid)
3932 /* card type isn't set correctly */
3933 if (card[btv->c.nr] < bttv_num_tvcards) {
3934 printk(KERN_WARNING "bttv%d: osprey eeprom: "
3935 "Not overriding user specified card type\n", btv->c.nr);
3937 printk(KERN_INFO "bttv%d: osprey eeprom: "
3938 "Changing card type from %d to %d\n", btv->c.nr,
3939 btv->c.type, cardid);
3940 btv->c.type = cardid;
3944 /* ----------------------------------------------------------------------- */
3945 /* AVermedia specific stuff, from bktr_card.c */
3947 static int tuner_0_table[] = {
3948 TUNER_PHILIPS_NTSC, TUNER_PHILIPS_PAL /* PAL-BG*/,
3949 TUNER_PHILIPS_PAL, TUNER_PHILIPS_PAL /* PAL-I*/,
3950 TUNER_PHILIPS_PAL, TUNER_PHILIPS_PAL,
3951 TUNER_PHILIPS_SECAM, TUNER_PHILIPS_SECAM,
3952 TUNER_PHILIPS_SECAM, TUNER_PHILIPS_PAL,
3953 TUNER_PHILIPS_FM1216ME_MK3 };
3955 static int tuner_1_table[] = {
3956 TUNER_TEMIC_NTSC, TUNER_TEMIC_PAL,
3957 TUNER_TEMIC_PAL, TUNER_TEMIC_PAL,
3958 TUNER_TEMIC_PAL, TUNER_TEMIC_PAL,
3959 TUNER_TEMIC_4012FY5, TUNER_TEMIC_4012FY5, /* TUNER_TEMIC_SECAM */
3960 TUNER_TEMIC_4012FY5, TUNER_TEMIC_PAL};
3962 static void __devinit avermedia_eeprom(struct bttv *btv)
3964 int tuner_make,tuner_tv_fm,tuner_format,tuner=0;
3966 tuner_make = (eeprom_data[0x41] & 0x7);
3967 tuner_tv_fm = (eeprom_data[0x41] & 0x18) >> 3;
3968 tuner_format = (eeprom_data[0x42] & 0xf0) >> 4;
3969 btv->has_remote = (eeprom_data[0x42] & 0x01);
3971 if (tuner_make == 0 || tuner_make == 2)
3972 if(tuner_format <=0x0a)
3973 tuner = tuner_0_table[tuner_format];
3974 if (tuner_make == 1)
3975 if(tuner_format <=9)
3976 tuner = tuner_1_table[tuner_format];
3978 if (tuner_make == 4)
3979 if(tuner_format == 0x09)
3980 tuner = TUNER_LG_NTSC_NEW_TAPC; /* TAPC-G702P */
3982 printk(KERN_INFO "bttv%d: Avermedia eeprom[0x%02x%02x]: tuner=",
3983 btv->c.nr,eeprom_data[0x41],eeprom_data[0x42]);
3985 btv->tuner_type=tuner;
3988 printk("Unknown type");
3989 printk(" radio:%s remote control:%s\n",
3990 tuner_tv_fm ? "yes" : "no",
3991 btv->has_remote ? "yes" : "no");
3994 /* used on Voodoo TV/FM (Voodoo 200), S0 wired to 0x10000 */
3995 void bttv_tda9880_setnorm(struct bttv *btv, int norm)
3997 /* fix up our card entry */
3998 if(norm==V4L2_STD_NTSC) {
3999 bttv_tvcards[BTTV_BOARD_VOODOOTV_FM].gpiomux[TVAUDIO_INPUT_TUNER]=0x957fff;
4000 bttv_tvcards[BTTV_BOARD_VOODOOTV_FM].gpiomute=0x957fff;
4001 bttv_tvcards[BTTV_BOARD_VOODOOTV_200].gpiomux[TVAUDIO_INPUT_TUNER]=0x957fff;
4002 bttv_tvcards[BTTV_BOARD_VOODOOTV_200].gpiomute=0x957fff;
4003 dprintk("bttv_tda9880_setnorm to NTSC\n");
4006 bttv_tvcards[BTTV_BOARD_VOODOOTV_FM].gpiomux[TVAUDIO_INPUT_TUNER]=0x947fff;
4007 bttv_tvcards[BTTV_BOARD_VOODOOTV_FM].gpiomute=0x947fff;
4008 bttv_tvcards[BTTV_BOARD_VOODOOTV_200].gpiomux[TVAUDIO_INPUT_TUNER]=0x947fff;
4009 bttv_tvcards[BTTV_BOARD_VOODOOTV_200].gpiomute=0x947fff;
4010 dprintk("bttv_tda9880_setnorm to PAL\n");
4012 /* set GPIO according */
4013 gpio_bits(bttv_tvcards[btv->c.type].gpiomask,
4014 bttv_tvcards[btv->c.type].gpiomux[btv->audio]);
4019 * reset/enable the MSP on some Hauppauge cards
4020 * Thanks to Kyösti Mälkki (kmalkki@cc.hut.fi)!
4025 static void __devinit boot_msp34xx(struct bttv *btv, int pin)
4027 int mask = (1 << pin);
4029 gpio_inout(mask,mask);
4032 gpio_bits(mask,mask);
4035 bttv_gpio_tracking(btv,"msp34xx");
4037 printk(KERN_INFO "bttv%d: Hauppauge/Voodoo msp34xx: reset line "
4038 "init [%d]\n", btv->c.nr, pin);
4041 static void __devinit boot_bt832(struct bttv *btv)
4045 /* ----------------------------------------------------------------------- */
4046 /* Imagenation L-Model PXC200 Framegrabber */
4047 /* This is basically the same procedure as
4048 * used by Alessandro Rubini in his pxc200
4049 * driver, but using BTTV functions */
4051 static void __devinit init_PXC200(struct bttv *btv)
4053 static int vals[] __devinitdata = { 0x08, 0x09, 0x0a, 0x0b, 0x0d, 0x0d,
4054 0x01, 0x02, 0x03, 0x04, 0x05, 0x06,
4060 /* Initialise GPIO-connevted stuff */
4061 gpio_inout(0xffffff, (1<<13));
4065 /* GPIO inputs are pulled up, so no need to drive
4066 * reset pin any longer */
4067 gpio_bits(0xffffff, 0);
4069 bttv_gpio_tracking(btv,"pxc200");
4071 /* we could/should try and reset/control the AD pots? but
4072 right now we simply turned off the crushing. Without
4073 this the AGC drifts drifts
4074 remember the EN is reverse logic -->
4075 setting BT848_ADC_AGC_EN disable the AGC
4076 tboult@eecs.lehigh.edu
4079 btwrite(BT848_ADC_RESERVED|BT848_ADC_AGC_EN, BT848_ADC);
4081 /* Initialise MAX517 DAC */
4082 printk(KERN_INFO "Setting DAC reference voltage level ...\n");
4083 bttv_I2CWrite(btv,0x5E,0,0x80,1);
4085 /* Initialise 12C508 PIC */
4086 /* The I2CWrite and I2CRead commmands are actually to the
4087 * same chips - but the R/W bit is included in the address
4088 * argument so the numbers are different */
4091 printk(KERN_INFO "Initialising 12C508 PIC chip ...\n");
4093 /* First of all, enable the clock line. This is used in the PXC200-F */
4094 val = btread(BT848_GPIO_DMA_CTL);
4095 val |= BT848_GPIO_DMA_CTL_GPCLKMODE;
4096 btwrite(val, BT848_GPIO_DMA_CTL);
4098 /* Then, push to 0 the reset pin long enough to reset the *
4099 * device same as above for the reset line, but not the same
4100 * value sent to the GPIO-connected stuff
4101 * which one is the good one? */
4102 gpio_inout(0xffffff,(1<<2));
4107 for (i = 0; i < ARRAY_SIZE(vals); i++) {
4108 tmp=bttv_I2CWrite(btv,0x1E,0,vals[i],1);
4111 "I2C Write(%2.2x) = %i\nI2C Read () = %2.2x\n\n",
4112 vals[i],tmp,bttv_I2CRead(btv,0x1F,NULL));
4116 printk(KERN_INFO "PXC200 Initialised.\n");
4121 /* ----------------------------------------------------------------------- */
4123 * The Adlink RTV-24 (aka Angelo) has some special initialisation to unlock
4124 * it. This apparently involves the following procedure for each 878 chip:
4126 * 1) write 0x00C3FEFF to the GPIO_OUT_EN register
4128 * 2) write to GPIO_DATA
4134 * read from GPIO_DATA into buf (uint_32)
4135 * - if ( data>>18 & 0x01 != 0) || ( buf>>19 & 0x01 != 1 )
4136 * error. ERROR_CPLD_Check_Failed stop.
4138 * 3) write to GPIO_DATA
4139 * - write 0x4400 + 0x0E
4141 * - write 0x4410 + 0x0E
4144 * read from GPIO_DATA into buf (uint_32)
4145 * - if ( buf>>18 & 0x01 ) || ( buf>>19 & 0x01 != 0 )
4146 * error. ERROR_CPLD_Check_Failed.
4148 /* ----------------------------------------------------------------------- */
4150 init_RTV24 (struct bttv *btv)
4152 uint32_t dataRead = 0;
4153 long watchdog_value = 0x0E;
4156 "bttv%d: Adlink RTV-24 initialisation in progress ...\n",
4159 btwrite (0x00c3feff, BT848_GPIO_OUT_EN);
4161 btwrite (0 + watchdog_value, BT848_GPIO_DATA);
4163 btwrite (0x10 + watchdog_value, BT848_GPIO_DATA);
4165 btwrite (0 + watchdog_value, BT848_GPIO_DATA);
4167 dataRead = btread (BT848_GPIO_DATA);
4169 if ((((dataRead >> 18) & 0x01) != 0) || (((dataRead >> 19) & 0x01) != 1)) {
4171 "bttv%d: Adlink RTV-24 initialisation(1) ERROR_CPLD_Check_Failed (read %d)\n",
4172 btv->c.nr, dataRead);
4175 btwrite (0x4400 + watchdog_value, BT848_GPIO_DATA);
4177 btwrite (0x4410 + watchdog_value, BT848_GPIO_DATA);
4179 btwrite (watchdog_value, BT848_GPIO_DATA);
4181 dataRead = btread (BT848_GPIO_DATA);
4183 if ((((dataRead >> 18) & 0x01) != 0) || (((dataRead >> 19) & 0x01) != 0)) {
4185 "bttv%d: Adlink RTV-24 initialisation(2) ERROR_CPLD_Check_Failed (read %d)\n",
4186 btv->c.nr, dataRead);
4192 "bttv%d: Adlink RTV-24 initialisation complete.\n", btv->c.nr);
4197 /* ----------------------------------------------------------------------- */
4198 /* Miro Pro radio stuff -- the tea5757 is connected to some GPIO ports */
4200 * Copyright (c) 1999 Csaba Halasz <qgehali@uni-miskolc.hu>
4201 * This code is placed under the terms of the GNU General Public License
4203 * Brutally hacked by Dan Sheridan <dan.sheridan@contact.org.uk> djs52 8/3/00
4206 static void bus_low(struct bttv *btv, int bit)
4208 if (btv->mbox_ior) {
4209 gpio_bits(btv->mbox_ior | btv->mbox_iow | btv->mbox_csel,
4210 btv->mbox_ior | btv->mbox_iow | btv->mbox_csel);
4217 if (btv->mbox_ior) {
4218 gpio_bits(btv->mbox_iow | btv->mbox_csel, 0);
4223 static void bus_high(struct bttv *btv, int bit)
4225 if (btv->mbox_ior) {
4226 gpio_bits(btv->mbox_ior | btv->mbox_iow | btv->mbox_csel,
4227 btv->mbox_ior | btv->mbox_iow | btv->mbox_csel);
4234 if (btv->mbox_ior) {
4235 gpio_bits(btv->mbox_iow | btv->mbox_csel, 0);
4240 static int bus_in(struct bttv *btv, int bit)
4242 if (btv->mbox_ior) {
4243 gpio_bits(btv->mbox_ior | btv->mbox_iow | btv->mbox_csel,
4244 btv->mbox_ior | btv->mbox_iow | btv->mbox_csel);
4247 gpio_bits(btv->mbox_iow | btv->mbox_csel, 0);
4250 return gpio_read() & (bit);
4253 /* TEA5757 register bits */
4254 #define TEA_FREQ 0:14
4255 #define TEA_BUFFER 15:15
4257 #define TEA_SIGNAL_STRENGTH 16:17
4259 #define TEA_PORT1 18:18
4260 #define TEA_PORT0 19:19
4262 #define TEA_BAND 20:21
4263 #define TEA_BAND_FM 0
4264 #define TEA_BAND_MW 1
4265 #define TEA_BAND_LW 2
4266 #define TEA_BAND_SW 3
4268 #define TEA_MONO 22:22
4269 #define TEA_ALLOW_STEREO 0
4270 #define TEA_FORCE_MONO 1
4272 #define TEA_SEARCH_DIRECTION 23:23
4273 #define TEA_SEARCH_DOWN 0
4274 #define TEA_SEARCH_UP 1
4276 #define TEA_STATUS 24:24
4277 #define TEA_STATUS_TUNED 0
4278 #define TEA_STATUS_SEARCHING 1
4280 /* Low-level stuff */
4281 static int tea5757_read(struct bttv *btv)
4283 unsigned long timeout;
4287 /* better safe than sorry */
4288 gpio_inout(btv->mbox_mask, btv->mbox_clk | btv->mbox_we);
4290 if (btv->mbox_ior) {
4291 gpio_bits(btv->mbox_ior | btv->mbox_iow | btv->mbox_csel,
4292 btv->mbox_ior | btv->mbox_iow | btv->mbox_csel);
4297 bttv_gpio_tracking(btv,"tea5757 read");
4299 bus_low(btv,btv->mbox_we);
4300 bus_low(btv,btv->mbox_clk);
4303 timeout= jiffies + msecs_to_jiffies(1000);
4305 /* wait for DATA line to go low; error if it doesn't */
4306 while (bus_in(btv,btv->mbox_data) && time_before(jiffies, timeout))
4308 if (bus_in(btv,btv->mbox_data)) {
4309 printk(KERN_WARNING "bttv%d: tea5757: read timeout\n",btv->c.nr);
4313 dprintk("bttv%d: tea5757:",btv->c.nr);
4314 for (i = 0; i < 24; i++) {
4316 bus_high(btv,btv->mbox_clk);
4318 dprintk("%c",(bus_in(btv,btv->mbox_most) == 0)?'T':'-');
4319 bus_low(btv,btv->mbox_clk);
4321 value |= (bus_in(btv,btv->mbox_data) == 0)?0:1; /* MSB first */
4322 dprintk("%c", (bus_in(btv,btv->mbox_most) == 0)?'S':'M');
4324 dprintk("\nbttv%d: tea5757: read 0x%X\n", btv->c.nr, value);
4328 static int tea5757_write(struct bttv *btv, int value)
4333 gpio_inout(btv->mbox_mask, btv->mbox_clk | btv->mbox_we | btv->mbox_data);
4335 if (btv->mbox_ior) {
4336 gpio_bits(btv->mbox_ior | btv->mbox_iow | btv->mbox_csel,
4337 btv->mbox_ior | btv->mbox_iow | btv->mbox_csel);
4341 bttv_gpio_tracking(btv,"tea5757 write");
4343 dprintk("bttv%d: tea5757: write 0x%X\n", btv->c.nr, value);
4344 bus_low(btv,btv->mbox_clk);
4345 bus_high(btv,btv->mbox_we);
4346 for (i = 0; i < 25; i++) {
4347 if (reg & 0x1000000)
4348 bus_high(btv,btv->mbox_data);
4350 bus_low(btv,btv->mbox_data);
4352 bus_high(btv,btv->mbox_clk);
4354 bus_low(btv,btv->mbox_clk);
4357 bus_low(btv,btv->mbox_we); /* unmute !!! */
4361 void tea5757_set_freq(struct bttv *btv, unsigned short freq)
4363 dprintk("tea5757_set_freq %d\n",freq);
4364 tea5757_write(btv, 5 * freq + 0x358); /* add 10.7MHz (see docs) */
4367 /* RemoteVision MX (rv605) muxsel helper [Miguel Freitas]
4369 * This is needed because rv605 don't use a normal multiplex, but a crosspoint
4370 * switch instead (CD22M3494E). This IC can have multiple active connections
4371 * between Xn (input) and Yn (output) pins. We need to clear any existing
4372 * connection prior to establish a new one, pulsing the STROBE pin.
4374 * The board hardwire Y0 (xpoint) to MUX1 and MUXOUT to Yin.
4375 * GPIO pins are wired as:
4376 * GPIO[0:3] - AX[0:3] (xpoint) - P1[0:3] (microcontroller)
4377 * GPIO[4:6] - AY[0:2] (xpoint) - P1[4:6] (microcontroller)
4378 * GPIO[7] - DATA (xpoint) - P1[7] (microcontroller)
4379 * GPIO[8] - - P3[5] (microcontroller)
4380 * GPIO[9] - RESET (xpoint) - P3[6] (microcontroller)
4381 * GPIO[10] - STROBE (xpoint) - P3[7] (microcontroller)
4382 * GPINTR - - P3[4] (microcontroller)
4384 * The microcontroller is a 80C32 like. It should be possible to change xpoint
4385 * configuration either directly (as we are doing) or using the microcontroller
4386 * which is also wired to I2C interface. I have no further info on the
4387 * microcontroller features, one would need to disassembly the firmware.
4388 * note: the vendor refused to give any information on this product, all
4389 * that stuff was found using a multimeter! :)
4391 static void rv605_muxsel(struct bttv *btv, unsigned int input)
4393 /* reset all conections */
4394 gpio_bits(0x200,0x200);
4396 gpio_bits(0x200,0x000);
4399 /* create a new connection */
4400 gpio_bits(0x480,0x080);
4401 gpio_bits(0x480,0x480);
4403 gpio_bits(0x480,0x080);
4407 /* Tibet Systems 'Progress DVR' CS16 muxsel helper [Chris Fanning]
4409 * The CS16 (available on eBay cheap) is a PCI board with four Fusion
4410 * 878A chips, a PCI bridge, an Atmel microcontroller, four sync seperator
4411 * chips, ten eight input analog multiplexors, a not chip and a few
4414 * 16 inputs on a secondary bracket are provided and can be selected
4415 * from each of the four capture chips. Two of the eight input
4416 * multiplexors are used to select from any of the 16 input signals.
4418 * Unsupported hardware capabilities:
4419 * . A video output monitor on the secondary bracket can be selected from
4420 * one of the 878A chips.
4421 * . Another passthrough but I haven't spent any time investigating it.
4422 * . Digital I/O (logic level connected to GPIO) is available from an
4425 * The on chip input mux should always be set to 2.
4426 * GPIO[16:19] - Video input selection
4427 * GPIO[0:3] - Video output monitor select (only available from one 878A)
4428 * GPIO[?:?] - Digital I/O.
4430 * There is an ATMEL microcontroller with an 8031 core on board. I have not
4431 * determined what function (if any) it provides. With the microcontroller
4432 * and sync seperator chips a guess is that it might have to do with video
4433 * switching and maybe some digital I/O.
4435 static void tibetCS16_muxsel(struct bttv *btv, unsigned int input)
4438 gpio_bits(0x0f0000, input << 16);
4441 static void tibetCS16_init(struct bttv *btv)
4443 /* enable gpio bits, mask obtained via btSpy */
4444 gpio_inout(0xffffff, 0x0f7fff);
4445 gpio_write(0x0f7fff);
4449 * The following routines for the Kodicom-4400r get a little mind-twisting.
4450 * There is a "master" controller and three "slave" controllers, together
4451 * an analog switch which connects any of 16 cameras to any of the BT87A's.
4452 * The analog switch is controlled by the "master", but the detection order
4453 * of the four BT878A chips is in an order which I just don't understand.
4454 * The "master" is actually the second controller to be detected. The
4455 * logic on the board uses logical numbers for the 4 controllers, but
4456 * those numbers are different from the detection sequence. When working
4457 * with the analog switch, we need to "map" from the detection sequence
4458 * over to the board's logical controller number. This mapping sequence
4459 * is {3, 0, 2, 1}, i.e. the first controller to be detected is logical
4460 * unit 3, the second (which is the master) is logical unit 0, etc.
4461 * We need to maintain the status of the analog switch (which of the 16
4462 * cameras is connected to which of the 4 controllers). Rather than
4463 * add to the bttv structure for this, we use the data reserved for
4464 * the mbox (unused for this card type).
4468 * First a routine to set the analog switch, which controls which camera
4469 * is routed to which controller. The switch comprises an X-address
4470 * (gpio bits 0-3, representing the camera, ranging from 0-15), and a
4471 * Y-address (gpio bits 4-6, representing the controller, ranging from 0-3).
4472 * A data value (gpio bit 7) of '1' enables the switch, and '0' disables
4473 * the switch. A STROBE bit (gpio bit 8) latches the data value into the
4474 * specified address. The idea is to set the address and data, then bring
4475 * STROBE high, and finally bring STROBE back to low.
4477 static void kodicom4400r_write(struct bttv *btv,
4478 unsigned char xaddr,
4479 unsigned char yaddr,
4480 unsigned char data) {
4483 udata = (data << 7) | ((yaddr&3) << 4) | (xaddr&0xf);
4484 gpio_bits(0x1ff, udata); /* write ADDR and DAT */
4485 gpio_bits(0x1ff, udata | (1 << 8)); /* strobe high */
4486 gpio_bits(0x1ff, udata); /* strobe low */
4490 * Next the mux select. Both the "master" and "slave" 'cards' (controllers)
4491 * use this routine. The routine finds the "master" for the card, maps
4492 * the controller number from the detected position over to the logical
4493 * number, writes the appropriate data to the analog switch, and housekeeps
4494 * the local copy of the switch information. The parameter 'input' is the
4495 * requested camera number (0 - 15).
4497 static void kodicom4400r_muxsel(struct bttv *btv, unsigned int input)
4502 static unsigned char map[4] = {3, 0, 2, 1};
4504 mctlr = master[btv->c.nr];
4505 if (mctlr == NULL) { /* ignore if master not yet detected */
4508 yaddr = (btv->c.nr - mctlr->c.nr + 1) & 3; /* the '&' is for safety */
4510 sw_status = (char *)(&mctlr->mbox_we);
4511 xaddr = input & 0xf;
4512 /* Check if the controller/camera pair has changed, else ignore */
4513 if (sw_status[yaddr] != xaddr)
4515 /* "open" the old switch, "close" the new one, save the new */
4516 kodicom4400r_write(mctlr, sw_status[yaddr], yaddr, 0);
4517 sw_status[yaddr] = xaddr;
4518 kodicom4400r_write(mctlr, xaddr, yaddr, 1);
4523 * During initialisation, we need to reset the analog switch. We
4524 * also preset the switch to map the 4 connectors on the card to the
4525 * *user's* (see above description of kodicom4400r_muxsel) channels
4528 static void kodicom4400r_init(struct bttv *btv)
4530 char *sw_status = (char *)(&btv->mbox_we);
4533 gpio_inout(0x0003ff, 0x0003ff);
4534 gpio_write(1 << 9); /* reset MUX */
4536 /* Preset camera 0 to the 4 controllers */
4537 for (ix = 0; ix < 4; ix++) {
4539 kodicom4400r_write(btv, ix, ix, 1);
4542 * Since this is the "master", we need to set up the
4543 * other three controller chips' pointers to this structure
4544 * for later use in the muxsel routine.
4546 if ((btv->c.nr<1) || (btv->c.nr>BTTV_MAX-3))
4548 master[btv->c.nr-1] = btv;
4549 master[btv->c.nr] = btv;
4550 master[btv->c.nr+1] = btv;
4551 master[btv->c.nr+2] = btv;
4554 /* The Grandtec X-Guard framegrabber card uses two Dual 4-channel
4555 * video multiplexers to provide up to 16 video inputs. These
4556 * multiplexers are controlled by the lower 8 GPIO pins of the
4557 * bt878. The multiplexers probably Pericom PI5V331Q or similar.
4559 * xxx0 is pin xxx of multiplexer U5,
4560 * yyy1 is pin yyy of multiplexer U2
4572 static void xguard_muxsel(struct bttv *btv, unsigned int input)
4574 static const int masks[] = {
4575 ENB0, ENB0|IN00, ENB0|IN10, ENB0|IN00|IN10,
4576 ENA0, ENA0|IN00, ENA0|IN10, ENA0|IN00|IN10,
4577 ENB1, ENB1|IN01, ENB1|IN11, ENB1|IN01|IN11,
4578 ENA1, ENA1|IN01, ENA1|IN11, ENA1|IN01|IN11,
4580 gpio_write(masks[input%16]);
4582 static void picolo_tetra_init(struct bttv *btv)
4584 /*This is the video input redirection fonctionality : I DID NOT USED IT. */
4585 btwrite (0x08<<16,BT848_GPIO_DATA);/*GPIO[19] [==> 4053 B+C] set to 1 */
4586 btwrite (0x04<<16,BT848_GPIO_DATA);/*GPIO[18] [==> 4053 A] set to 1*/
4588 static void picolo_tetra_muxsel (struct bttv* btv, unsigned int input)
4591 dprintk (KERN_DEBUG "bttv%d : picolo_tetra_muxsel => input = %d\n",btv->c.nr,input);
4592 /*Just set the right path in the analog multiplexers : channel 1 -> 4 ==> Analog Mux ==> MUX0*/
4593 /*GPIO[20]&GPIO[21] used to choose the right input*/
4594 btwrite (input<<20,BT848_GPIO_DATA);
4599 * ivc120_muxsel [Added by Alan Garfield <alan@fromorbit.com>]
4601 * The IVC120G security card has 4 i2c controlled TDA8540 matrix
4602 * swichers to provide 16 channels to MUX0. The TDA8540's have
4603 * 4 independent outputs and as such the IVC120G also has the
4604 * optional "Monitor Out" bus. This allows the card to be looking
4605 * at one input while the monitor is looking at another.
4607 * Since I've couldn't be bothered figuring out how to add an
4608 * independant muxsel for the monitor bus, I've just set it to
4609 * whatever the card is looking at.
4611 * OUT0 of the TDA8540's is connected to MUX0 (0x03)
4612 * OUT1 of the TDA8540's is connected to "Monitor Out" (0x0C)
4614 * TDA8540_ALT3 IN0-3 = Channel 13 - 16 (0x03)
4615 * TDA8540_ALT4 IN0-3 = Channel 1 - 4 (0x03)
4616 * TDA8540_ALT5 IN0-3 = Channel 5 - 8 (0x03)
4617 * TDA8540_ALT6 IN0-3 = Channel 9 - 12 (0x03)
4621 /* All 7 possible sub-ids for the TDA8540 Matrix Switcher */
4622 #define I2C_TDA8540 0x90
4623 #define I2C_TDA8540_ALT1 0x92
4624 #define I2C_TDA8540_ALT2 0x94
4625 #define I2C_TDA8540_ALT3 0x96
4626 #define I2C_TDA8540_ALT4 0x98
4627 #define I2C_TDA8540_ALT5 0x9a
4628 #define I2C_TDA8540_ALT6 0x9c
4630 static void ivc120_muxsel(struct bttv *btv, unsigned int input)
4633 int key = input % 4;
4634 int matrix = input / 4;
4636 dprintk("bttv%d: ivc120_muxsel: Input - %02d | TDA - %02d | In - %02d\n",
4637 btv->c.nr, input, matrix, key);
4639 /* Handles the input selection on the TDA8540's */
4640 bttv_I2CWrite(btv, I2C_TDA8540_ALT3, 0x00,
4641 ((matrix == 3) ? (key | key << 2) : 0x00), 1);
4642 bttv_I2CWrite(btv, I2C_TDA8540_ALT4, 0x00,
4643 ((matrix == 0) ? (key | key << 2) : 0x00), 1);
4644 bttv_I2CWrite(btv, I2C_TDA8540_ALT5, 0x00,
4645 ((matrix == 1) ? (key | key << 2) : 0x00), 1);
4646 bttv_I2CWrite(btv, I2C_TDA8540_ALT6, 0x00,
4647 ((matrix == 2) ? (key | key << 2) : 0x00), 1);
4649 /* Handles the output enables on the TDA8540's */
4650 bttv_I2CWrite(btv, I2C_TDA8540_ALT3, 0x02,
4651 ((matrix == 3) ? 0x03 : 0x00), 1); /* 13 - 16 */
4652 bttv_I2CWrite(btv, I2C_TDA8540_ALT4, 0x02,
4653 ((matrix == 0) ? 0x03 : 0x00), 1); /* 1-4 */
4654 bttv_I2CWrite(btv, I2C_TDA8540_ALT5, 0x02,
4655 ((matrix == 1) ? 0x03 : 0x00), 1); /* 5-8 */
4656 bttv_I2CWrite(btv, I2C_TDA8540_ALT6, 0x02,
4657 ((matrix == 2) ? 0x03 : 0x00), 1); /* 9-12 */
4659 /* Selects MUX0 for input on the 878 */
4660 btaor((0)<<5, ~(3<<5), BT848_IFORM);
4664 /* PXC200 muxsel helper
4665 * luke@syseng.anu.edu.au
4666 * another transplant
4667 * from Alessandro Rubini (rubini@linux.it)
4669 * There are 4 kinds of cards:
4670 * PXC200L which is bt848
4671 * PXC200F which is bt848 with PIC controlling mux
4672 * PXC200AL which is bt878
4673 * PXC200AF which is bt878 with PIC controlling mux
4675 #define PX_CFG_PXC200F 0x01
4676 #define PX_FLAG_PXC200A 0x00001000 /* a pxc200A is bt-878 based */
4677 #define PX_I2C_PIC 0x0f
4678 #define PX_PXC200A_CARDID 0x200a1295
4679 #define PX_I2C_CMD_CFG 0x00
4681 static void PXC200_muxsel(struct bttv *btv, unsigned int input)
4686 unsigned char buf[2];
4688 /* Read PIC config to determine if this is a PXC200F */
4692 rc=bttv_I2CWrite(btv,(PX_I2C_PIC<<1),buf[0],buf[1],1);
4694 printk(KERN_DEBUG "bttv%d: PXC200_muxsel: pic cfg write failed:%d\n", btv->c.nr,rc);
4695 /* not PXC ? do nothing */
4699 rc=bttv_I2CRead(btv,(PX_I2C_PIC<<1),NULL);
4700 if (!(rc & PX_CFG_PXC200F)) {
4701 printk(KERN_DEBUG "bttv%d: PXC200_muxsel: not PXC200F rc:%d \n", btv->c.nr,rc);
4706 /* The multiplexer in the 200F is handled by the GPIO port */
4707 /* get correct mapping between inputs */
4708 /* mux = bttv_tvcards[btv->type].muxsel[input] & 3; */
4709 /* ** not needed!? */
4712 /* make sure output pins are enabled */
4713 /* bitmask=0x30f; */
4715 /* check whether we have a PXC200A */
4716 if (btv->cardid == PX_PXC200A_CARDID) {
4717 bitmask ^= 0x180; /* use 7 and 9, not 8 and 9 */
4718 bitmask |= 7<<4; /* the DAC */
4720 btwrite(bitmask, BT848_GPIO_OUT_EN);
4722 bitmask = btread(BT848_GPIO_DATA);
4723 if (btv->cardid == PX_PXC200A_CARDID)
4724 bitmask = (bitmask & ~0x280) | ((mux & 2) << 8) | ((mux & 1) << 7);
4725 else /* older device */
4726 bitmask = (bitmask & ~0x300) | ((mux & 3) << 8);
4727 btwrite(bitmask,BT848_GPIO_DATA);
4730 * Was "to be safe, set the bt848 to input 0"
4731 * Actually, since it's ok at load time, better not messing
4732 * with these bits (on PXC200AF you need to set mux 2 here)
4734 * needed because bttv-driver sets mux before calling this function
4736 if (btv->cardid == PX_PXC200A_CARDID)
4737 btaor(2<<5, ~BT848_IFORM_MUXSEL, BT848_IFORM);
4738 else /* older device */
4739 btand(~BT848_IFORM_MUXSEL,BT848_IFORM);
4741 printk(KERN_DEBUG "bttv%d: setting input channel to:%d\n", btv->c.nr,(int)mux);
4744 /* ----------------------------------------------------------------------- */
4745 /* motherboard chipset specific stuff */
4747 void __init bttv_check_chipset(void)
4749 int pcipci_fail = 0;
4750 struct pci_dev *dev = NULL;
4752 if (pci_pci_problems & (PCIPCI_FAIL|PCIAGP_FAIL)) /* should check if target is AGP */
4754 if (pci_pci_problems & (PCIPCI_TRITON|PCIPCI_NATOMA|PCIPCI_VIAETBF))
4756 if (pci_pci_problems & PCIPCI_VSFX)
4758 #ifdef PCIPCI_ALIMAGIK
4759 if (pci_pci_problems & PCIPCI_ALIMAGIK)
4764 /* print warnings about any quirks found */
4766 printk(KERN_INFO "bttv: Host bridge needs ETBF enabled.\n");
4768 printk(KERN_INFO "bttv: Host bridge needs VSFX enabled.\n");
4770 printk(KERN_INFO "bttv: bttv and your chipset may not work "
4773 printk(KERN_INFO "bttv: overlay will be disabled.\n");
4776 printk(KERN_INFO "bttv: overlay forced. Use this "
4777 "option at your own risk.\n");
4780 if (UNSET != latency)
4781 printk(KERN_INFO "bttv: pci latency fixup [%d]\n",latency);
4782 while ((dev = pci_get_device(PCI_VENDOR_ID_INTEL,
4783 PCI_DEVICE_ID_INTEL_82441, dev))) {
4785 pci_read_config_byte(dev, 0x53, &b);
4787 printk(KERN_INFO "bttv: Host bridge: 82441FX Natoma, "
4788 "bufcon=0x%02x\n",b);
4792 int __devinit bttv_handle_chipset(struct bttv *btv)
4794 unsigned char command;
4796 if (!triton1 && !vsfx && UNSET == latency)
4801 printk(KERN_INFO "bttv%d: enabling ETBF (430FX/VP3 compatibilty)\n",btv->c.nr);
4802 if (vsfx && btv->id >= 878)
4803 printk(KERN_INFO "bttv%d: enabling VSFX\n",btv->c.nr);
4804 if (UNSET != latency)
4805 printk(KERN_INFO "bttv%d: setting pci timer to %d\n",
4809 if (btv->id < 878) {
4810 /* bt848 (mis)uses a bit in the irq mask for etbf */
4812 btv->triton1 = BT848_INT_ETBF;
4814 /* bt878 has a bit in the pci config space for it */
4815 pci_read_config_byte(btv->c.pci, BT878_DEVCTRL, &command);
4817 command |= BT878_EN_TBFX;
4819 command |= BT878_EN_VSFX;
4820 pci_write_config_byte(btv->c.pci, BT878_DEVCTRL, command);
4822 if (UNSET != latency)
4823 pci_write_config_byte(btv->c.pci, PCI_LATENCY_TIMER, latency);
projects / linux-2.6 / blob