git.oblomov.eu Git - linux-2.6/blob - drivers/staging/winbond/wbusb.c

   1 /*
   2  * Copyright 2008 Pavel Machek <pavel@suse.cz>
   3  *
   4  * Distribute under GPLv2.
   5  *
   6  * The original driver was written by:
   7  *     Jeff Lee <YY_Lee@issc.com.tw>
   8  *
   9  * and was adapted to the 2.6 kernel by:
  10  *     Costantino Leandro (Rxart Desktop) <le_costantino@pixartargentina.com.ar>
  11  */
  12 #include <net/mac80211.h>
  13 #include <linux/usb.h>
  14
  15 #include "core.h"
  16 #include "mds_f.h"
  17 #include "mlmetxrx_f.h"
  18 #include "mto.h"
  19 #include "wbhal_f.h"
  20 #include "wblinux_f.h"
  21
  22 MODULE_DESCRIPTION("IS89C35 802.11bg WLAN USB Driver");
  23 MODULE_LICENSE("GPL");
  24 MODULE_VERSION("0.1");
  25
  26 static struct usb_device_id wb35_table[] __devinitdata = {
  27         { USB_DEVICE(0x0416, 0x0035) },
  28         { USB_DEVICE(0x18E8, 0x6201) },
  29         { USB_DEVICE(0x18E8, 0x6206) },
  30         { USB_DEVICE(0x18E8, 0x6217) },
  31         { USB_DEVICE(0x18E8, 0x6230) },
  32         { USB_DEVICE(0x18E8, 0x6233) },
  33         { USB_DEVICE(0x1131, 0x2035) },
  34         { 0, }
  35 };
  36
  37 MODULE_DEVICE_TABLE(usb, wb35_table);
  38
  39 static struct ieee80211_rate wbsoft_rates[] = {
  40         { .bitrate = 10, .flags = IEEE80211_RATE_SHORT_PREAMBLE },
  41 };
  42
  43 static struct ieee80211_channel wbsoft_channels[] = {
  44         { .center_freq = 2412 },
  45 };
  46
  47 static struct ieee80211_supported_band wbsoft_band_2GHz = {
  48         .channels       = wbsoft_channels,
  49         .n_channels     = ARRAY_SIZE(wbsoft_channels),
  50         .bitrates       = wbsoft_rates,
  51         .n_bitrates     = ARRAY_SIZE(wbsoft_rates),
  52 };
  53
  54 static int wbsoft_add_interface(struct ieee80211_hw *dev,
  55                                 struct ieee80211_if_init_conf *conf)
  56 {
  57         printk("wbsoft_add interface called\n");
  58         return 0;
  59 }
  60
  61 static void wbsoft_remove_interface(struct ieee80211_hw *dev,
  62                                     struct ieee80211_if_init_conf *conf)
  63 {
  64         printk("wbsoft_remove interface called\n");
  65 }
  66
  67 static void wbsoft_stop(struct ieee80211_hw *hw)
  68 {
  69         printk(KERN_INFO "%s called\n", __func__);
  70 }
  71
  72 static int wbsoft_get_stats(struct ieee80211_hw *hw,
  73                             struct ieee80211_low_level_stats *stats)
  74 {
  75         printk(KERN_INFO "%s called\n", __func__);
  76         return 0;
  77 }
  78
  79 static int wbsoft_get_tx_stats(struct ieee80211_hw *hw,
  80                                struct ieee80211_tx_queue_stats *stats)
  81 {
  82         printk(KERN_INFO "%s called\n", __func__);
  83         return 0;
  84 }
  85
  86 static void wbsoft_configure_filter(struct ieee80211_hw *dev,
  87                                     unsigned int changed_flags,
  88                                     unsigned int *total_flags,
  89                                     int mc_count, struct dev_mc_list *mclist)
  90 {
  91         unsigned int new_flags;
  92
  93         new_flags = 0;
  94
  95         if (*total_flags & FIF_PROMISC_IN_BSS)
  96                 new_flags |= FIF_PROMISC_IN_BSS;
  97         else if ((*total_flags & FIF_ALLMULTI) || (mc_count > 32))
  98                 new_flags |= FIF_ALLMULTI;
  99
 100         dev->flags &= ~IEEE80211_HW_RX_INCLUDES_FCS;
 101
 102         *total_flags = new_flags;
 103 }
 104
 105 static int wbsoft_tx(struct ieee80211_hw *dev, struct sk_buff *skb)
 106 {
 107         struct wbsoft_priv *priv = dev->priv;
 108
 109         MLMESendFrame(priv, skb->data, skb->len, FRAME_TYPE_802_11_MANAGEMENT);
 110
 111         return NETDEV_TX_OK;
 112 }
 113
 114 static int wbsoft_start(struct ieee80211_hw *dev)
 115 {
 116         struct wbsoft_priv *priv = dev->priv;
 117
 118         priv->enabled = true;
 119
 120         return 0;
 121 }
 122
 123 static void hal_set_radio_mode(struct hw_data *pHwData, unsigned char radio_off)
 124 {
 125         struct wb35_reg *reg = &pHwData->reg;
 126
 127         if (pHwData->SurpriseRemove)
 128                 return;
 129
 130         if (radio_off)          //disable Baseband receive off
 131         {
 132                 pHwData->CurrentRadioSw = 1;    // off
 133                 reg->M24_MacControl &= 0xffffffbf;
 134         } else {
 135                 pHwData->CurrentRadioSw = 0;    // on
 136                 reg->M24_MacControl |= 0x00000040;
 137         }
 138         Wb35Reg_Write(pHwData, 0x0824, reg->M24_MacControl);
 139 }
 140
 141 static void hal_set_beacon_period(struct hw_data *pHwData, u16 beacon_period)
 142 {
 143         u32 tmp;
 144
 145         if (pHwData->SurpriseRemove)
 146                 return;
 147
 148         pHwData->BeaconPeriod = beacon_period;
 149         tmp = pHwData->BeaconPeriod << 16;
 150         tmp |= pHwData->ProbeDelay;
 151         Wb35Reg_Write(pHwData, 0x0848, tmp);
 152 }
 153
 154 static void
 155 hal_set_current_channel_ex(struct hw_data *pHwData, ChanInfo channel)
 156 {
 157         struct wb35_reg *reg = &pHwData->reg;
 158
 159         if (pHwData->SurpriseRemove)
 160                 return;
 161
 162         printk("Going to channel: %d/%d\n", channel.band, channel.ChanNo);
 163
 164         RFSynthesizer_SwitchingChannel(pHwData, channel);       // Switch channel
 165         pHwData->Channel = channel.ChanNo;
 166         pHwData->band = channel.band;
 167 #ifdef _PE_STATE_DUMP_
 168         printk("Set channel is %d, band =%d\n", pHwData->Channel,
 169                pHwData->band);
 170 #endif
 171         reg->M28_MacControl &= ~0xff;   // Clean channel information field
 172         reg->M28_MacControl |= channel.ChanNo;
 173         Wb35Reg_WriteWithCallbackValue(pHwData, 0x0828, reg->M28_MacControl,
 174                                        (s8 *) & channel, sizeof(ChanInfo));
 175 }
 176
 177 static void hal_set_current_channel(struct hw_data *pHwData, ChanInfo channel)
 178 {
 179         hal_set_current_channel_ex(pHwData, channel);
 180 }
 181
 182 static void hal_set_accept_broadcast(struct hw_data *pHwData, u8 enable)
 183 {
 184         struct wb35_reg *reg = &pHwData->reg;
 185
 186         if (pHwData->SurpriseRemove)
 187                 return;
 188
 189         reg->M00_MacControl &= ~0x02000000;     //The HW value
 190
 191         if (enable)
 192                 reg->M00_MacControl |= 0x02000000;      //The HW value
 193
 194         Wb35Reg_Write(pHwData, 0x0800, reg->M00_MacControl);
 195 }
 196
 197 //for wep key error detection, we need to accept broadcast packets to be received temporary.
 198 static void hal_set_accept_promiscuous(struct hw_data *pHwData, u8 enable)
 199 {
 200         struct wb35_reg *reg = &pHwData->reg;
 201
 202         if (pHwData->SurpriseRemove)
 203                 return;
 204         if (enable) {
 205                 reg->M00_MacControl |= 0x00400000;
 206                 Wb35Reg_Write(pHwData, 0x0800, reg->M00_MacControl);
 207         } else {
 208                 reg->M00_MacControl &= ~0x00400000;
 209                 Wb35Reg_Write(pHwData, 0x0800, reg->M00_MacControl);
 210         }
 211 }
 212
 213 static void hal_set_accept_multicast(struct hw_data *pHwData, u8 enable)
 214 {
 215         struct wb35_reg *reg = &pHwData->reg;
 216
 217         if (pHwData->SurpriseRemove)
 218                 return;
 219
 220         reg->M00_MacControl &= ~0x01000000;     //The HW value
 221         if (enable)
 222                 reg->M00_MacControl |= 0x01000000;      //The HW value
 223         Wb35Reg_Write(pHwData, 0x0800, reg->M00_MacControl);
 224 }
 225
 226 static void hal_set_accept_beacon(struct hw_data *pHwData, u8 enable)
 227 {
 228         struct wb35_reg *reg = &pHwData->reg;
 229
 230         if (pHwData->SurpriseRemove)
 231                 return;
 232
 233         // 20040108 debug
 234         if (!enable)            //Due to SME and MLME are not suitable for 35
 235                 return;
 236
 237         reg->M00_MacControl &= ~0x04000000;     //The HW value
 238         if (enable)
 239                 reg->M00_MacControl |= 0x04000000;      //The HW value
 240
 241         Wb35Reg_Write(pHwData, 0x0800, reg->M00_MacControl);
 242 }
 243
 244 static int wbsoft_config(struct ieee80211_hw *dev, u32 changed)
 245 {
 246         struct wbsoft_priv *priv = dev->priv;
 247         struct ieee80211_conf *conf = &dev->conf;
 248         ChanInfo ch;
 249
 250         printk("wbsoft_config called\n");
 251
 252         /* Should use channel_num, or something, as that is already pre-translated */
 253         ch.band = 1;
 254         ch.ChanNo = 1;
 255
 256         hal_set_current_channel(&priv->sHwData, ch);
 257         hal_set_beacon_period(&priv->sHwData, conf->beacon_int);
 258         hal_set_accept_broadcast(&priv->sHwData, 1);
 259         hal_set_accept_promiscuous(&priv->sHwData, 1);
 260         hal_set_accept_multicast(&priv->sHwData, 1);
 261         hal_set_accept_beacon(&priv->sHwData, 1);
 262         hal_set_radio_mode(&priv->sHwData, 0);
 263
 264         return 0;
 265 }
 266
 267 static u64 wbsoft_get_tsf(struct ieee80211_hw *dev)
 268 {
 269         printk("wbsoft_get_tsf called\n");
 270         return 0;
 271 }
 272
 273 static const struct ieee80211_ops wbsoft_ops = {
 274         .tx                     = wbsoft_tx,
 275         .start                  = wbsoft_start,
 276         .stop                   = wbsoft_stop,
 277         .add_interface          = wbsoft_add_interface,
 278         .remove_interface       = wbsoft_remove_interface,
 279         .config                 = wbsoft_config,
 280         .configure_filter       = wbsoft_configure_filter,
 281         .get_stats              = wbsoft_get_stats,
 282         .get_tx_stats           = wbsoft_get_tx_stats,
 283         .get_tsf                = wbsoft_get_tsf,
 284 };
 285
 286 static void
 287 hal_set_ethernet_address(struct hw_data *pHwData, u8 * current_address)
 288 {
 289         u32 ltmp[2];
 290
 291         if (pHwData->SurpriseRemove)
 292                 return;
 293
 294         memcpy(pHwData->CurrentMacAddress, current_address, ETH_ALEN);
 295
 296         ltmp[0] = cpu_to_le32(*(u32 *) pHwData->CurrentMacAddress);
 297         ltmp[1] =
 298             cpu_to_le32(*(u32 *) (pHwData->CurrentMacAddress + 4)) & 0xffff;
 299
 300         Wb35Reg_BurstWrite(pHwData, 0x03e8, ltmp, 2, AUTO_INCREMENT);
 301 }
 302
 303 static void
 304 hal_get_permanent_address(struct hw_data *pHwData, u8 * pethernet_address)
 305 {
 306         if (pHwData->SurpriseRemove)
 307                 return;
 308
 309         memcpy(pethernet_address, pHwData->PermanentMacAddress, 6);
 310 }
 311
 312 static void hal_stop(struct hw_data *pHwData)
 313 {
 314         struct wb35_reg *reg = &pHwData->reg;
 315
 316         pHwData->Wb35Rx.rx_halt = 1;
 317         Wb35Rx_stop(pHwData);
 318
 319         pHwData->Wb35Tx.tx_halt = 1;
 320         Wb35Tx_stop(pHwData);
 321
 322         reg->D00_DmaControl &= ~0xc0000000;     //Tx Off, Rx Off
 323         Wb35Reg_Write(pHwData, 0x0400, reg->D00_DmaControl);
 324 }
 325
 326 static unsigned char hal_idle(struct hw_data *pHwData)
 327 {
 328         struct wb35_reg *reg = &pHwData->reg;
 329         struct wb_usb *pWbUsb = &pHwData->WbUsb;
 330
 331         if (!pHwData->SurpriseRemove
 332             && (pWbUsb->DetectCount || reg->EP0vm_state != VM_STOP))
 333                 return false;
 334
 335         return true;
 336 }
 337
 338 u8 hal_get_antenna_number(struct hw_data *pHwData)
 339 {
 340         struct wb35_reg *reg = &pHwData->reg;
 341
 342         if ((reg->BB2C & BIT(11)) == 0)
 343                 return 0;
 344         else
 345                 return 1;
 346 }
 347
 348 /* 0 : radio on; 1: radio off */
 349 static u8 hal_get_hw_radio_off(struct hw_data * pHwData)
 350 {
 351         struct wb35_reg *reg = &pHwData->reg;
 352
 353         if (pHwData->SurpriseRemove)
 354                 return 1;
 355
 356         //read the bit16 of register U1B0
 357         Wb35Reg_Read(pHwData, 0x3b0, &reg->U1B0);
 358         if ((reg->U1B0 & 0x00010000)) {
 359                 pHwData->CurrentRadioHw = 1;
 360                 return 1;
 361         } else {
 362                 pHwData->CurrentRadioHw = 0;
 363                 return 0;
 364         }
 365 }
 366
 367 static u8 LED_GRAY[20] = {
 368         0, 3, 4, 6, 8, 10, 11, 12, 13, 14, 15, 14, 13, 12, 11, 10, 8, 6, 4, 2
 369 };
 370
 371 static u8 LED_GRAY2[30] = {
 372         7, 8, 9, 10, 11, 12, 13, 14, 15, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0,
 373         0, 15, 14, 13, 12, 11, 10, 9, 8
 374 };
 375
 376 static void hal_led_control(unsigned long data)
 377 {
 378         struct wbsoft_priv *adapter = (struct wbsoft_priv *)data;
 379         struct hw_data *pHwData = &adapter->sHwData;
 380         struct wb35_reg *reg = &pHwData->reg;
 381         u32 LEDSet = (pHwData->SoftwareSet & HAL_LED_SET_MASK) >> HAL_LED_SET_SHIFT;
 382         u32 TimeInterval = 500, ltmp, ltmp2;
 383         ltmp = 0;
 384
 385         if (pHwData->SurpriseRemove)
 386                 return;
 387
 388         if (pHwData->LED_control) {
 389                 ltmp2 = pHwData->LED_control & 0xff;
 390                 if (ltmp2 == 5) // 5 is WPS mode
 391                 {
 392                         TimeInterval = 100;
 393                         ltmp2 = (pHwData->LED_control >> 8) & 0xff;
 394                         switch (ltmp2) {
 395                         case 1: // [0.2 On][0.1 Off]...
 396                                 pHwData->LED_Blinking %= 3;
 397                                 ltmp = 0x1010;  // Led 1 & 0 Green and Red
 398                                 if (pHwData->LED_Blinking == 2) // Turn off
 399                                         ltmp = 0;
 400                                 break;
 401                         case 2: // [0.1 On][0.1 Off]...
 402                                 pHwData->LED_Blinking %= 2;
 403                                 ltmp = 0x0010;  // Led 0 red color
 404                                 if (pHwData->LED_Blinking)      // Turn off
 405                                         ltmp = 0;
 406                                 break;
 407                         case 3: // [0.1 On][0.1 Off][0.1 On][0.1 Off][0.1 On][0.1 Off][0.1 On][0.1 Off][0.1 On][0.1 Off][0.5 Off]...
 408                                 pHwData->LED_Blinking %= 15;
 409                                 ltmp = 0x0010;  // Led 0 red color
 410                                 if ((pHwData->LED_Blinking >= 9) || (pHwData->LED_Blinking % 2))        // Turn off 0.6 sec
 411                                         ltmp = 0;
 412                                 break;
 413                         case 4: // [300 On][ off ]
 414                                 ltmp = 0x1000;  // Led 1 Green color
 415                                 if (pHwData->LED_Blinking >= 3000)
 416                                         ltmp = 0;       // led maybe on after 300sec * 32bit counter overlap.
 417                                 break;
 418                         }
 419                         pHwData->LED_Blinking++;
 420
 421                         reg->U1BC_LEDConfigure = ltmp;
 422                         if (LEDSet != 7)        // Only 111 mode has 2 LEDs on PCB.
 423                         {
 424                                 reg->U1BC_LEDConfigure |= (ltmp & 0xff) << 8;   // Copy LED result to each LED control register
 425                                 reg->U1BC_LEDConfigure |= (ltmp & 0xff00) >> 8;
 426                         }
 427                         Wb35Reg_Write(pHwData, 0x03bc, reg->U1BC_LEDConfigure);
 428                 }
 429         } else if (pHwData->CurrentRadioSw || pHwData->CurrentRadioHw)  // If radio off
 430         {
 431                 if (reg->U1BC_LEDConfigure & 0x1010) {
 432                         reg->U1BC_LEDConfigure &= ~0x1010;
 433                         Wb35Reg_Write(pHwData, 0x03bc, reg->U1BC_LEDConfigure);
 434                 }
 435         } else {
 436                 switch (LEDSet) {
 437                 case 4: // [100] Only 1 Led be placed on PCB and use pin 21 of IC. Use LED_0 for showing
 438                         if (!pHwData->LED_LinkOn)       // Blink only if not Link On
 439                         {
 440                                 // Blinking if scanning is on progress
 441                                 if (pHwData->LED_Scanning) {
 442                                         if (pHwData->LED_Blinking == 0) {
 443                                                 reg->U1BC_LEDConfigure |= 0x10;
 444                                                 Wb35Reg_Write(pHwData, 0x03bc, reg->U1BC_LEDConfigure); // LED_0 On
 445                                                 pHwData->LED_Blinking = 1;
 446                                                 TimeInterval = 300;
 447                                         } else {
 448                                                 reg->U1BC_LEDConfigure &= ~0x10;
 449                                                 Wb35Reg_Write(pHwData, 0x03bc, reg->U1BC_LEDConfigure); // LED_0 Off
 450                                                 pHwData->LED_Blinking = 0;
 451                                                 TimeInterval = 300;
 452                                         }
 453                                 } else {
 454                                         //Turn Off LED_0
 455                                         if (reg->U1BC_LEDConfigure & 0x10) {
 456                                                 reg->U1BC_LEDConfigure &= ~0x10;
 457                                                 Wb35Reg_Write(pHwData, 0x03bc, reg->U1BC_LEDConfigure); // LED_0 Off
 458                                         }
 459                                 }
 460                         } else {
 461                                 // Turn On LED_0
 462                                 if ((reg->U1BC_LEDConfigure & 0x10) == 0) {
 463                                         reg->U1BC_LEDConfigure |= 0x10;
 464                                         Wb35Reg_Write(pHwData, 0x03bc, reg->U1BC_LEDConfigure); // LED_0 Off
 465                                 }
 466                         }
 467                         break;
 468
 469                 case 6: // [110] Only 1 Led be placed on PCB and use pin 21 of IC. Use LED_0 for showing
 470                         if (!pHwData->LED_LinkOn)       // Blink only if not Link On
 471                         {
 472                                 // Blinking if scanning is on progress
 473                                 if (pHwData->LED_Scanning) {
 474                                         if (pHwData->LED_Blinking == 0) {
 475                                                 reg->U1BC_LEDConfigure &= ~0xf;
 476                                                 reg->U1BC_LEDConfigure |= 0x10;
 477                                                 Wb35Reg_Write(pHwData, 0x03bc, reg->U1BC_LEDConfigure); // LED_0 On
 478                                                 pHwData->LED_Blinking = 1;
 479                                                 TimeInterval = 300;
 480                                         } else {
 481                                                 reg->U1BC_LEDConfigure &= ~0x1f;
 482                                                 Wb35Reg_Write(pHwData, 0x03bc, reg->U1BC_LEDConfigure); // LED_0 Off
 483                                                 pHwData->LED_Blinking = 0;
 484                                                 TimeInterval = 300;
 485                                         }
 486                                 } else {
 487                                         // 20060901 Gray blinking if in disconnect state and not scanning
 488                                         ltmp = reg->U1BC_LEDConfigure;
 489                                         reg->U1BC_LEDConfigure &= ~0x1f;
 490                                         if (LED_GRAY2[(pHwData->LED_Blinking % 30)]) {
 491                                                 reg->U1BC_LEDConfigure |= 0x10;
 492                                                 reg->U1BC_LEDConfigure |=
 493                                                     LED_GRAY2[(pHwData->LED_Blinking % 30)];
 494                                         }
 495                                         pHwData->LED_Blinking++;
 496                                         if (reg->U1BC_LEDConfigure != ltmp)
 497                                                 Wb35Reg_Write(pHwData, 0x03bc, reg->U1BC_LEDConfigure); // LED_0 Off
 498                                         TimeInterval = 100;
 499                                 }
 500                         } else {
 501                                 // Turn On LED_0
 502                                 if ((reg->U1BC_LEDConfigure & 0x10) == 0) {
 503                                         reg->U1BC_LEDConfigure |= 0x10;
 504                                         Wb35Reg_Write(pHwData, 0x03bc, reg->U1BC_LEDConfigure); // LED_0 Off
 505                                 }
 506                         }
 507                         break;
 508
 509                 case 5: // [101] Only 1 Led be placed on PCB and use LED_1 for showing
 510                         if (!pHwData->LED_LinkOn)       // Blink only if not Link On
 511                         {
 512                                 // Blinking if scanning is on progress
 513                                 if (pHwData->LED_Scanning) {
 514                                         if (pHwData->LED_Blinking == 0) {
 515                                                 reg->U1BC_LEDConfigure |=
 516                                                     0x1000;
 517                                                 Wb35Reg_Write(pHwData, 0x03bc, reg->U1BC_LEDConfigure); // LED_1 On
 518                                                 pHwData->LED_Blinking = 1;
 519                                                 TimeInterval = 300;
 520                                         } else {
 521                                                 reg->U1BC_LEDConfigure &=
 522                                                     ~0x1000;
 523                                                 Wb35Reg_Write(pHwData, 0x03bc, reg->U1BC_LEDConfigure); // LED_1 Off
 524                                                 pHwData->LED_Blinking = 0;
 525                                                 TimeInterval = 300;
 526                                         }
 527                                 } else {
 528                                         //Turn Off LED_1
 529                                         if (reg->U1BC_LEDConfigure & 0x1000) {
 530                                                 reg->U1BC_LEDConfigure &=
 531                                                     ~0x1000;
 532                                                 Wb35Reg_Write(pHwData, 0x03bc, reg->U1BC_LEDConfigure); // LED_1 Off
 533                                         }
 534                                 }
 535                         } else {
 536                                 // Is transmitting/receiving ??
 537                                 if ((adapter->RxByteCount !=
 538                                      pHwData->RxByteCountLast)
 539                                     || (adapter->TxByteCount !=
 540                                         pHwData->TxByteCountLast)) {
 541                                         if ((reg->U1BC_LEDConfigure & 0x3000) !=
 542                                             0x3000) {
 543                                                 reg->U1BC_LEDConfigure |=
 544                                                     0x3000;
 545                                                 Wb35Reg_Write(pHwData, 0x03bc, reg->U1BC_LEDConfigure); // LED_1 On
 546                                         }
 547                                         // Update variable
 548                                         pHwData->RxByteCountLast =
 549                                             adapter->RxByteCount;
 550                                         pHwData->TxByteCountLast =
 551                                             adapter->TxByteCount;
 552                                         TimeInterval = 200;
 553                                 } else {
 554                                         // Turn On LED_1 and blinking if transmitting/receiving
 555                                         if ((reg->U1BC_LEDConfigure & 0x3000) !=
 556                                             0x1000) {
 557                                                 reg->U1BC_LEDConfigure &=
 558                                                     ~0x3000;
 559                                                 reg->U1BC_LEDConfigure |=
 560                                                     0x1000;
 561                                                 Wb35Reg_Write(pHwData, 0x03bc, reg->U1BC_LEDConfigure); // LED_1 On
 562                                         }
 563                                 }
 564                         }
 565                         break;
 566
 567                 default:        // Default setting. 2 LED be placed on PCB. LED_0: Link On LED_1 Active
 568                         if ((reg->U1BC_LEDConfigure & 0x3000) != 0x3000) {
 569                                 reg->U1BC_LEDConfigure |= 0x3000;       // LED_1 is always on and event enable
 570                                 Wb35Reg_Write(pHwData, 0x03bc,
 571                                               reg->U1BC_LEDConfigure);
 572                         }
 573
 574                         if (pHwData->LED_Blinking) {
 575                                 // Gray blinking
 576                                 reg->U1BC_LEDConfigure &= ~0x0f;
 577                                 reg->U1BC_LEDConfigure |= 0x10;
 578                                 reg->U1BC_LEDConfigure |=
 579                                     LED_GRAY[(pHwData->LED_Blinking - 1) % 20];
 580                                 Wb35Reg_Write(pHwData, 0x03bc,
 581                                               reg->U1BC_LEDConfigure);
 582
 583                                 pHwData->LED_Blinking += 2;
 584                                 if (pHwData->LED_Blinking < 40)
 585                                         TimeInterval = 100;
 586                                 else {
 587                                         pHwData->LED_Blinking = 0;      // Stop blinking
 588                                         reg->U1BC_LEDConfigure &= ~0x0f;
 589                                         Wb35Reg_Write(pHwData, 0x03bc,
 590                                                       reg->U1BC_LEDConfigure);
 591                                 }
 592                                 break;
 593                         }
 594
 595                         if (pHwData->LED_LinkOn) {
 596                                 if (!(reg->U1BC_LEDConfigure & 0x10))   // Check the LED_0
 597                                 {
 598                                         //Try to turn ON LED_0 after gray blinking
 599                                         reg->U1BC_LEDConfigure |= 0x10;
 600                                         pHwData->LED_Blinking = 1;      //Start blinking
 601                                         TimeInterval = 50;
 602                                 }
 603                         } else {
 604                                 if (reg->U1BC_LEDConfigure & 0x10)      // Check the LED_0
 605                                 {
 606                                         reg->U1BC_LEDConfigure &= ~0x10;
 607                                         Wb35Reg_Write(pHwData, 0x03bc,
 608                                                       reg->U1BC_LEDConfigure);
 609                                 }
 610                         }
 611                         break;
 612                 }
 613
 614                 //20060828.1 Active send null packet to avoid AP disconnect
 615                 if (pHwData->LED_LinkOn) {
 616                         pHwData->NullPacketCount += TimeInterval;
 617                         if (pHwData->NullPacketCount >=
 618                             DEFAULT_NULL_PACKET_COUNT) {
 619                                 pHwData->NullPacketCount = 0;
 620                         }
 621                 }
 622         }
 623
 624         pHwData->time_count += TimeInterval;
 625         Wb35Tx_CurrentTime(adapter, pHwData->time_count);       // 20060928 add
 626         pHwData->LEDTimer.expires = jiffies + msecs_to_jiffies(TimeInterval);
 627         add_timer(&pHwData->LEDTimer);
 628 }
 629
 630 static int hal_init_hardware(struct ieee80211_hw *hw)
 631 {
 632         struct wbsoft_priv *priv = hw->priv;
 633         struct hw_data *pHwData = &priv->sHwData;
 634         u16 SoftwareSet;
 635
 636         pHwData->MaxReceiveLifeTime = DEFAULT_MSDU_LIFE_TIME;
 637         pHwData->FragmentThreshold = DEFAULT_FRAGMENT_THRESHOLD;
 638
 639         if (!Wb35Reg_initial(pHwData))
 640                 goto error_reg_destroy;
 641
 642         if (!Wb35Tx_initial(pHwData))
 643                 goto error_tx_destroy;
 644
 645         if (!Wb35Rx_initial(pHwData))
 646                 goto error_rx_destroy;
 647
 648         init_timer(&pHwData->LEDTimer);
 649         pHwData->LEDTimer.function = hal_led_control;
 650         pHwData->LEDTimer.data = (unsigned long)priv;
 651         pHwData->LEDTimer.expires = jiffies + msecs_to_jiffies(1000);
 652         add_timer(&pHwData->LEDTimer);
 653
 654         SoftwareSet = hal_software_set(pHwData);
 655
 656 #ifdef Vendor2
 657         // Try to make sure the EEPROM contain
 658         SoftwareSet >>= 8;
 659         if (SoftwareSet != 0x82)
 660                 return false;
 661 #endif
 662
 663         Wb35Rx_start(hw);
 664         Wb35Tx_EP2VM_start(priv);
 665
 666         return 0;
 667
 668 error_rx_destroy:
 669         Wb35Rx_destroy(pHwData);
 670 error_tx_destroy:
 671         Wb35Tx_destroy(pHwData);
 672 error_reg_destroy:
 673         Wb35Reg_destroy(pHwData);
 674
 675         pHwData->SurpriseRemove = 1;
 676         return -EINVAL;
 677 }
 678
 679 static int wb35_hw_init(struct ieee80211_hw *hw)
 680 {
 681         struct wbsoft_priv *priv = hw->priv;
 682         struct hw_data *pHwData = &priv->sHwData;
 683         u8 EEPROM_region;
 684         u8 HwRadioOff;
 685         u8 *pMacAddr2;
 686         u8 *pMacAddr;
 687         int err;
 688
 689         pHwData->phy_type = RF_DECIDE_BY_INF;
 690
 691         priv->Mds.TxRTSThreshold                = DEFAULT_RTSThreshold;
 692         priv->Mds.TxFragmentThreshold           = DEFAULT_FRAGMENT_THRESHOLD;
 693
 694         priv->sLocalPara.region_INF             = REGION_AUTO;
 695         priv->sLocalPara.TxRateMode             = RATE_AUTO;
 696         priv->sLocalPara.bMacOperationMode      = MODE_802_11_BG;
 697         priv->sLocalPara.MTUsize                = MAX_ETHERNET_PACKET_SIZE;
 698         priv->sLocalPara.bPreambleMode          = AUTO_MODE;
 699         priv->sLocalPara.bWepKeyError           = false;
 700         priv->sLocalPara.bToSelfPacketReceived  = false;
 701         priv->sLocalPara.WepKeyDetectTimerCount = 2 * 100; /* 2 seconds */
 702
 703         priv->sLocalPara.RadioOffStatus.boSwRadioOff = false;
 704
 705         err = hal_init_hardware(hw);
 706         if (err)
 707                 goto error;
 708
 709         EEPROM_region = hal_get_region_from_EEPROM(pHwData);
 710         if (EEPROM_region != REGION_AUTO)
 711                 priv->sLocalPara.region = EEPROM_region;
 712         else {
 713                 if (priv->sLocalPara.region_INF != REGION_AUTO)
 714                         priv->sLocalPara.region = priv->sLocalPara.region_INF;
 715                 else
 716                         priv->sLocalPara.region = REGION_USA;   /* default setting */
 717         }
 718
 719         // Get Software setting flag from hal
 720         priv->sLocalPara.boAntennaDiversity = false;
 721         if (hal_software_set(pHwData) & 0x00000001)
 722                 priv->sLocalPara.boAntennaDiversity = true;
 723
 724         Mds_initial(priv);
 725
 726         /*
 727          * If no user-defined address in the registry, use the addresss
 728          * "burned" on the NIC instead.
 729          */
 730         pMacAddr = priv->sLocalPara.ThisMacAddress;
 731         pMacAddr2 = priv->sLocalPara.PermanentAddress;
 732
 733         /* Reading ethernet address from EEPROM */
 734         hal_get_permanent_address(pHwData, priv->sLocalPara.PermanentAddress);
 735         if (memcmp(pMacAddr, "\x00\x00\x00\x00\x00\x00", MAC_ADDR_LENGTH) == 0)
 736                 memcpy(pMacAddr, pMacAddr2, MAC_ADDR_LENGTH);
 737         else {
 738                 /* Set the user define MAC address */
 739                 hal_set_ethernet_address(pHwData,
 740                                          priv->sLocalPara.ThisMacAddress);
 741         }
 742
 743         priv->sLocalPara.bAntennaNo = hal_get_antenna_number(pHwData);
 744 #ifdef _PE_STATE_DUMP_
 745         printk("Driver init, antenna no = %d\n", psLOCAL->bAntennaNo);
 746 #endif
 747         hal_get_hw_radio_off(pHwData);
 748
 749         /* Waiting for HAL setting OK */
 750         while (!hal_idle(pHwData))
 751                 msleep(10);
 752
 753         MTO_Init(priv);
 754
 755         HwRadioOff = hal_get_hw_radio_off(pHwData);
 756         priv->sLocalPara.RadioOffStatus.boHwRadioOff = !!HwRadioOff;
 757
 758         hal_set_radio_mode(pHwData,
 759                            (unsigned char)(priv->sLocalPara.RadioOffStatus.
 760                                            boSwRadioOff
 761                                            || priv->sLocalPara.RadioOffStatus.
 762                                            boHwRadioOff));
 763
 764         /* Notify hal that the driver is ready now. */
 765         hal_driver_init_OK(pHwData) = 1;
 766
 767 error:
 768         return err;
 769 }
 770
 771 static int wb35_probe(struct usb_interface *intf,
 772                       const struct usb_device_id *id_table)
 773 {
 774         struct usb_device *udev = interface_to_usbdev(intf);
 775         struct usb_endpoint_descriptor *endpoint;
 776         struct usb_host_interface *interface;
 777         struct ieee80211_hw *dev;
 778         struct wbsoft_priv *priv;
 779         struct wb_usb *pWbUsb;
 780         int nr, err;
 781         u32 ltmp;
 782
 783         usb_get_dev(udev);
 784
 785         /* Check the device if it already be opened */
 786         nr = usb_control_msg(udev, usb_rcvctrlpipe(udev, 0),
 787                              0x01,
 788                              USB_TYPE_VENDOR | USB_RECIP_DEVICE | USB_DIR_IN,
 789                              0x0, 0x400, &ltmp, 4, HZ * 100);
 790         if (nr < 0) {
 791                 err = nr;
 792                 goto error;
 793         }
 794
 795         /* Is already initialized? */
 796         ltmp = cpu_to_le32(ltmp);
 797         if (ltmp) {
 798                 err = -EBUSY;
 799                 goto error;
 800         }
 801
 802         dev = ieee80211_alloc_hw(sizeof(*priv), &wbsoft_ops);
 803         if (!dev) {
 804                 err = -ENOMEM;
 805                 goto error;
 806         }
 807
 808         priv = dev->priv;
 809
 810         spin_lock_init(&priv->SpinLock);
 811
 812         pWbUsb = &priv->sHwData.WbUsb;
 813         pWbUsb->udev = udev;
 814
 815         interface = intf->cur_altsetting;
 816         endpoint = &interface->endpoint[0].desc;
 817
 818         if (endpoint[2].wMaxPacketSize == 512) {
 819                 printk("[w35und] Working on USB 2.0\n");
 820                 pWbUsb->IsUsb20 = 1;
 821         }
 822
 823         err = wb35_hw_init(dev);
 824         if (err)
 825                 goto error_free_hw;
 826
 827         SET_IEEE80211_DEV(dev, &udev->dev);
 828         {
 829                 struct hw_data *pHwData = &priv->sHwData;
 830                 unsigned char dev_addr[MAX_ADDR_LEN];
 831                 hal_get_permanent_address(pHwData, dev_addr);
 832                 SET_IEEE80211_PERM_ADDR(dev, dev_addr);
 833         }
 834
 835         dev->extra_tx_headroom = 12;    /* FIXME */
 836         dev->flags = IEEE80211_HW_SIGNAL_UNSPEC;
 837         dev->wiphy->interface_modes = BIT(NL80211_IFTYPE_STATION);
 838
 839         dev->channel_change_time = 1000;
 840         dev->max_signal = 100;
 841         dev->queues = 1;
 842
 843         dev->wiphy->bands[IEEE80211_BAND_2GHZ] = &wbsoft_band_2GHz;
 844
 845         err = ieee80211_register_hw(dev);
 846         if (err)
 847                 goto error_free_hw;
 848
 849         usb_set_intfdata(intf, dev);
 850
 851         return 0;
 852
 853 error_free_hw:
 854         ieee80211_free_hw(dev);
 855 error:
 856         usb_put_dev(udev);
 857         return err;
 858 }
 859
 860 static void hal_halt(struct hw_data *pHwData)
 861 {
 862         del_timer_sync(&pHwData->LEDTimer);
 863         /* XXX: Wait for Timer DPC exit. */
 864         msleep(100);
 865         Wb35Rx_destroy(pHwData);
 866         Wb35Tx_destroy(pHwData);
 867         Wb35Reg_destroy(pHwData);
 868 }
 869
 870 static void wb35_hw_halt(struct wbsoft_priv *adapter)
 871 {
 872         Mds_Destroy(adapter);
 873
 874         /* Turn off Rx and Tx hardware ability */
 875         hal_stop(&adapter->sHwData);
 876 #ifdef _PE_USB_INI_DUMP_
 877         printk("[w35und] Hal_stop O.K.\n");
 878 #endif
 879         /* Waiting Irp completed */
 880         msleep(100);
 881
 882         hal_halt(&adapter->sHwData);
 883 }
 884
 885 static void wb35_disconnect(struct usb_interface *intf)
 886 {
 887         struct ieee80211_hw *hw = usb_get_intfdata(intf);
 888         struct wbsoft_priv *priv = hw->priv;
 889
 890         wb35_hw_halt(priv);
 891
 892         ieee80211_stop_queues(hw);
 893         ieee80211_unregister_hw(hw);
 894         ieee80211_free_hw(hw);
 895
 896         usb_set_intfdata(intf, NULL);
 897         usb_put_dev(interface_to_usbdev(intf));
 898 }
 899
 900 static struct usb_driver wb35_driver = {
 901         .name           = "w35und",
 902         .id_table       = wb35_table,
 903         .probe          = wb35_probe,
 904         .disconnect     = wb35_disconnect,
 905 };
 906
 907 static int __init wb35_init(void)
 908 {
 909         return usb_register(&wb35_driver);
 910 }
 911
 912 static void __exit wb35_exit(void)
 913 {
 914         usb_deregister(&wb35_driver);
 915 }
 916
 917 module_init(wb35_init);
 918 module_exit(wb35_exit);