git.oblomov.eu Git - linux-2.6/blob - arch/avr32/boards/hammerhead/flash.c

   1 /*
   2  * Hammerhead board-specific flash initialization
   3  *
   4  * Copyright (C) 2008 Miromico AG
   5  *
   6  * This program is free software; you can redistribute it and/or modify
   7  * it under the terms of the GNU General Public License version 2 as
   8  * published by the Free Software Foundation.
   9  */
  10
  11 #include <linux/init.h>
  12 #include <linux/platform_device.h>
  13 #include <linux/mtd/mtd.h>
  14 #include <linux/mtd/partitions.h>
  15 #include <linux/mtd/physmap.h>
  16 #include <linux/usb/isp116x.h>
  17 #include <linux/dma-mapping.h>
  18 #include <linux/platform_device.h>
  19 #include <linux/delay.h>
  20
  21 #include <mach/portmux.h>
  22 #include <mach/at32ap700x.h>
  23 #include <mach/smc.h>
  24
  25 #include "../../mach-at32ap/clock.h"
  26 #include "flash.h"
  27
  28
  29 #define HAMMERHEAD_USB_PERIPH_GCLK0     0x40000000
  30 #define HAMMERHEAD_USB_PERIPH_CS2       0x02000000
  31 #define HAMMERHEAD_USB_PERIPH_EXTINT0   0x02000000
  32
  33 #define HAMMERHEAD_FPGA_PERIPH_MOSI     0x00000002
  34 #define HAMMERHEAD_FPGA_PERIPH_SCK      0x00000020
  35 #define HAMMERHEAD_FPGA_PERIPH_EXTINT3  0x10000000
  36
  37 static struct smc_timing flash_timing __initdata = {
  38         .ncs_read_setup         = 0,
  39         .nrd_setup              = 40,
  40         .ncs_write_setup        = 0,
  41         .nwe_setup              = 10,
  42
  43         .ncs_read_pulse         = 80,
  44         .nrd_pulse              = 40,
  45         .ncs_write_pulse        = 65,
  46         .nwe_pulse              = 55,
  47
  48         .read_cycle             = 120,
  49         .write_cycle            = 120,
  50 };
  51
  52 static struct smc_config flash_config __initdata = {
  53         .bus_width              = 2,
  54         .nrd_controlled         = 1,
  55         .nwe_controlled         = 1,
  56         .byte_write             = 1,
  57 };
  58
  59 static struct mtd_partition flash_parts[] = {
  60         {
  61                 .name           = "u-boot",
  62                 .offset         = 0x00000000,
  63                 .size           = 0x00020000,           /* 128 KiB */
  64                 .mask_flags     = MTD_WRITEABLE,
  65         },
  66         {
  67                 .name           = "root",
  68                 .offset         = 0x00020000,
  69                 .size           = 0x007d0000,
  70         },
  71         {
  72                 .name           = "env",
  73                 .offset         = 0x007f0000,
  74                 .size           = 0x00010000,
  75                 .mask_flags     = MTD_WRITEABLE,
  76         },
  77 };
  78
  79 static struct physmap_flash_data flash_data = {
  80         .width          = 2,
  81         .nr_parts       = ARRAY_SIZE(flash_parts),
  82         .parts          = flash_parts,
  83 };
  84
  85 static struct resource flash_resource = {
  86         .start          = 0x00000000,
  87         .end            = 0x007fffff,
  88         .flags          = IORESOURCE_MEM,
  89 };
  90
  91 static struct platform_device flash_device = {
  92         .name           = "physmap-flash",
  93         .id             = 0,
  94         .resource       = &flash_resource,
  95         .num_resources  = 1,
  96         .dev            = { .platform_data = &flash_data, },
  97 };
  98
  99 #ifdef CONFIG_BOARD_HAMMERHEAD_USB
 100
 101 static struct smc_timing isp1160_timing __initdata = {
 102         .ncs_read_setup         = 75,
 103         .nrd_setup              = 75,
 104         .ncs_write_setup        = 75,
 105         .nwe_setup              = 75,
 106
 107
 108         /* We use conservative timing settings, as the minimal settings aren't
 109            stable. There may be room for tweaking. */
 110         .ncs_read_pulse         = 75,  /* min. 33ns */
 111         .nrd_pulse              = 75,  /* min. 33ns */
 112         .ncs_write_pulse        = 75,  /* min. 26ns */
 113         .nwe_pulse              = 75,  /* min. 26ns */
 114
 115         .read_cycle             = 225, /* min. 143ns */
 116         .write_cycle            = 225, /* min. 136ns */
 117 };
 118
 119 static struct smc_config isp1160_config __initdata = {
 120         .bus_width              = 2,
 121         .nrd_controlled         = 1,
 122         .nwe_controlled         = 1,
 123         .byte_write             = 0,
 124 };
 125
 126 /*
 127  * The platform delay function is only used to enforce the strange
 128  * read to write delay. This can not be configured in the SMC. All other
 129  * timings are controlled by the SMC (see timings obove)
 130  * So in isp116x-hcd.c we should comment out USE_PLATFORM_DELAY
 131  */
 132 void isp116x_delay(struct device *dev, int delay)
 133 {
 134         if (delay > 150)
 135                 ndelay(delay - 150);
 136 }
 137
 138 static struct  isp116x_platform_data isp1160_data = {
 139         .sel15Kres              = 1,    /* use internal downstream resistors */
 140         .oc_enable              = 0,    /* external overcurrent detection */
 141         .int_edge_triggered     = 0,    /* interrupt is level triggered */
 142         .int_act_high           = 0,    /* interrupt is active low */
 143         .delay = isp116x_delay,         /* platform delay function */
 144 };
 145
 146 static struct resource isp1160_resource[] = {
 147         {
 148                 .start          = 0x08000000,
 149                 .end            = 0x08000001,
 150                 .flags          = IORESOURCE_MEM,
 151         },
 152         {
 153                 .start          = 0x08000002,
 154                 .end            = 0x08000003,
 155                 .flags          = IORESOURCE_MEM,
 156         },
 157         {
 158                 .start          = 64,
 159                 .flags          = IORESOURCE_IRQ,
 160         },
 161 };
 162
 163 static struct platform_device isp1160_device = {
 164         .name           = "isp116x-hcd",
 165         .id             = 0,
 166         .resource       = isp1160_resource,
 167         .num_resources  = 3,
 168         .dev            = {
 169                 .platform_data = &isp1160_data,
 170         },
 171 };
 172 #endif
 173
 174 #ifdef CONFIG_BOARD_HAMMERHEAD_USB
 175 static int __init hammerhead_usbh_init(void)
 176 {
 177         struct clk *gclk;
 178         struct clk *osc;
 179
 180         int ret;
 181
 182         /* setup smc for usbh */
 183         smc_set_timing(&isp1160_config, &isp1160_timing);
 184         ret = smc_set_configuration(2, &isp1160_config);
 185
 186         if (ret < 0) {
 187                 printk(KERN_ERR
 188                        "hammerhead: failed to set ISP1160 USBH timing\n");
 189                 return ret;
 190         }
 191
 192         /* setup gclk0 to run from osc1 */
 193         gclk = clk_get(NULL, "gclk0");
 194         if (IS_ERR(gclk))
 195                 goto err_gclk;
 196
 197         osc = clk_get(NULL, "osc1");
 198         if (IS_ERR(osc))
 199                 goto err_osc;
 200
 201         if (clk_set_parent(gclk, osc)) {
 202                 pr_debug("hammerhead: failed to set osc1 for USBH clock\n");
 203                 goto err_set_clk;
 204         }
 205
 206         /* set clock to 6MHz */
 207         clk_set_rate(gclk, 6000000);
 208
 209         /* and enable */
 210         clk_enable(gclk);
 211
 212         /* select GCLK0 peripheral function */
 213         at32_select_periph(GPIO_PIOA_BASE, HAMMERHEAD_USB_PERIPH_GCLK0,
 214                            GPIO_PERIPH_A, 0);
 215
 216         /* enable CS2 peripheral function */
 217         at32_select_periph(GPIO_PIOE_BASE, HAMMERHEAD_USB_PERIPH_CS2,
 218                            GPIO_PERIPH_A, 0);
 219
 220         /* H_WAKEUP must be driven low */
 221         at32_select_gpio(GPIO_PIN_PA(8), AT32_GPIOF_OUTPUT);
 222
 223         /* Select EXTINT0 for PB25 */
 224         at32_select_periph(GPIO_PIOB_BASE, HAMMERHEAD_USB_PERIPH_EXTINT0,
 225                            GPIO_PERIPH_A, 0);
 226
 227         /* register usbh device driver */
 228         platform_device_register(&isp1160_device);
 229
 230  err_set_clk:
 231         clk_put(osc);
 232  err_osc:
 233         clk_put(gclk);
 234  err_gclk:
 235         return ret;
 236 }
 237 #endif
 238
 239 #ifdef CONFIG_BOARD_HAMMERHEAD_FPGA
 240 static struct smc_timing fpga_timing __initdata = {
 241         .ncs_read_setup         = 16,
 242         .nrd_setup              = 32,
 243         .ncs_read_pulse         = 48,
 244         .nrd_pulse              = 32,
 245         .read_cycle             = 64,
 246
 247         .ncs_write_setup        = 16,
 248         .nwe_setup              = 16,
 249         .ncs_write_pulse        = 32,
 250         .nwe_pulse              = 32,
 251         .write_cycle            = 64,
 252 };
 253
 254 static struct smc_config fpga_config __initdata = {
 255         .bus_width              = 4,
 256         .nrd_controlled         = 1,
 257         .nwe_controlled         = 1,
 258         .byte_write             = 0,
 259 };
 260
 261 static struct resource hh_fpga0_resource[] = {
 262         {
 263                 .start          = 0xffe00400,
 264                 .end            = 0xffe00400 + 0x3ff,
 265                 .flags          = IORESOURCE_MEM,
 266         },
 267         {
 268                 .start          = 4,
 269                 .end            = 4,
 270                 .flags          = IORESOURCE_IRQ,
 271         },
 272         {
 273                 .start          = 0x0c000000,
 274                 .end            = 0x0c000100,
 275                 .flags          = IORESOURCE_MEM,
 276         },
 277         {
 278                 .start          = 67,
 279                 .end            = 67,
 280                 .flags          = IORESOURCE_IRQ,
 281         },
 282 };
 283
 284 static u64 hh_fpga0_dma_mask = DMA_32BIT_MASK;
 285 static struct platform_device hh_fpga0_device = {
 286         .name           = "hh_fpga",
 287         .id             = 0,
 288         .dev            = {
 289                 .dma_mask = &hh_fpga0_dma_mask,
 290                 .coherent_dma_mask = DMA_32BIT_MASK,
 291         },
 292         .resource       = hh_fpga0_resource,
 293         .num_resources  = ARRAY_SIZE(hh_fpga0_resource),
 294 };
 295
 296 static struct clk hh_fpga0_spi_clk = {
 297         .name           = "spi_clk",
 298         .dev            = &hh_fpga0_device.dev,
 299         .mode           = pba_clk_mode,
 300         .get_rate       = pba_clk_get_rate,
 301         .index          = 1,
 302 };
 303
 304 struct platform_device *__init at32_add_device_hh_fpga(void)
 305 {
 306         /* Select peripheral functionallity for SPI SCK and MOSI */
 307         at32_select_periph(GPIO_PIOB_BASE, HAMMERHEAD_FPGA_PERIPH_SCK,
 308                            GPIO_PERIPH_B, 0);
 309         at32_select_periph(GPIO_PIOB_BASE, HAMMERHEAD_FPGA_PERIPH_MOSI,
 310                            GPIO_PERIPH_B, 0);
 311
 312         /* reserve all other needed gpio
 313          * We have on board pull ups, so there is no need
 314          * to enable gpio pull ups */
 315         /* INIT_DONE (input) */
 316         at32_select_gpio(GPIO_PIN_PB(0), 0);
 317
 318         /* nSTATUS (input) */
 319         at32_select_gpio(GPIO_PIN_PB(2), 0);
 320
 321         /* nCONFIG (output, low) */
 322         at32_select_gpio(GPIO_PIN_PB(3), AT32_GPIOF_OUTPUT);
 323
 324         /* CONF_DONE (input) */
 325         at32_select_gpio(GPIO_PIN_PB(4), 0);
 326
 327         /* Select EXTINT3 for PB28 (Interrupt from FPGA) */
 328         at32_select_periph(GPIO_PIOB_BASE, HAMMERHEAD_FPGA_PERIPH_EXTINT3,
 329                            GPIO_PERIPH_A, 0);
 330
 331         /* Get our parent clock */
 332         hh_fpga0_spi_clk.parent = clk_get(NULL, "pba");
 333         clk_put(hh_fpga0_spi_clk.parent);
 334
 335         /* Register clock in at32 clock tree */
 336         at32_clk_register(&hh_fpga0_spi_clk);
 337
 338         platform_device_register(&hh_fpga0_device);
 339         return &hh_fpga0_device;
 340 }
 341 #endif
 342
 343 /* This needs to be called after the SMC has been initialized */
 344 static int __init hammerhead_flash_init(void)
 345 {
 346         int ret;
 347
 348         smc_set_timing(&flash_config, &flash_timing);
 349         ret = smc_set_configuration(0, &flash_config);
 350
 351         if (ret < 0) {
 352                 printk(KERN_ERR "hammerhead: failed to set NOR flash timing\n");
 353                 return ret;
 354         }
 355
 356         platform_device_register(&flash_device);
 357
 358 #ifdef CONFIG_BOARD_HAMMERHEAD_USB
 359         hammerhead_usbh_init();
 360 #endif
 361
 362 #ifdef CONFIG_BOARD_HAMMERHEAD_FPGA
 363         /* Setup SMC for FPGA interface */
 364         smc_set_timing(&fpga_config, &fpga_timing);
 365         ret = smc_set_configuration(3, &fpga_config);
 366 #endif
 367
 368
 369         if (ret < 0) {
 370                 printk(KERN_ERR "hammerhead: failed to set FPGA timing\n");
 371                 return ret;
 372         }
 373
 374         return 0;
 375 }
 376
 377 device_initcall(hammerhead_flash_init);