git.oblomov.eu Git - linux-2.6/blob - drivers/net/tokenring/tms380tr.h

   1 /*
   2  * tms380tr.h: TI TMS380 Token Ring driver for Linux
   3  *
   4  * Authors:
   5  * - Christoph Goos <cgoos@syskonnect.de>
   6  * - Adam Fritzler <mid@auk.cx>
   7  */
   8
   9 #ifndef __LINUX_TMS380TR_H
  10 #define __LINUX_TMS380TR_H
  11
  12 #ifdef __KERNEL__
  13
  14 #include <linux/interrupt.h>
  15
  16 /* module prototypes */
  17 int tms380tr_open(struct net_device *dev);
  18 int tms380tr_close(struct net_device *dev);
  19 irqreturn_t tms380tr_interrupt(int irq, void *dev_id);
  20 int tmsdev_init(struct net_device *dev, struct device *pdev);
  21 void tmsdev_term(struct net_device *dev);
  22 void tms380tr_wait(unsigned long time);
  23
  24 #define TMS380TR_MAX_ADAPTERS 7
  25
  26 #define SEND_TIMEOUT 10*HZ
  27
  28 #define TR_RCF_LONGEST_FRAME_MASK 0x0070
  29 #define TR_RCF_FRAME4K 0x0030
  30
  31 /*------------------------------------------------------------------*/
  32 /*  Bit order for adapter communication with DMA                    */
  33 /*  --------------------------------------------------------------  */
  34 /*  Bit  8 | 9| 10| 11|| 12| 13| 14| 15|| 0| 1| 2| 3|| 4| 5| 6| 7|  */
  35 /*  --------------------------------------------------------------  */
  36 /*  The bytes in a word must be byte swapped. Also, if a double     */
  37 /*  word is used for storage, then the words, as well as the bytes, */
  38 /*  must be swapped.                                                */
  39 /*  Bit order for adapter communication with DIO                    */
  40 /*  --------------------------------------------------------------  */
  41 /*  Bit  0 | 1| 2| 3|| 4| 5| 6| 7|| 8| 9| 10| 11|| 12| 13| 14| 15|  */
  42 /*  --------------------------------------------------------------  */
  43 /*------------------------------------------------------------------*/
  44
  45 /* Swap words of a long.                        */
  46 #define SWAPW(x) (((x) << 16) | ((x) >> 16))
  47
  48 /* Get the low byte of a word.                      */
  49 #define LOBYTE(w)       ((unsigned char)(w))
  50
  51 /* Get the high byte of a word.                     */
  52 #define HIBYTE(w)       ((unsigned char)((unsigned short)(w) >> 8))
  53
  54 /* Get the low word of a long.                      */
  55 #define LOWORD(l)       ((unsigned short)(l))
  56
  57 /* Get the high word of a long.                     */
  58 #define HIWORD(l)       ((unsigned short)((unsigned long)(l) >> 16))
  59
  60
  61
  62 /* Token ring adapter I/O addresses for normal mode. */
  63
  64 /*
  65  * The SIF registers.  Common to all adapters.
  66  */
  67 /* Basic SIF (SRSX = 0) */
  68 #define SIFDAT                  0x00    /* SIF/DMA data. */
  69 #define SIFINC                  0x02    /* IO Word data with auto increment. */
  70 #define SIFINH                  0x03    /* IO Byte data with auto increment. */
  71 #define SIFADR                  0x04    /* SIF/DMA Address. */
  72 #define SIFCMD                  0x06    /* SIF Command. */
  73 #define SIFSTS                  0x06    /* SIF Status. */
  74
  75 /* "Extended" SIF (SRSX = 1) */
  76 #define SIFACL                  0x08    /* SIF Adapter Control Register. */
  77 #define SIFADD                  0x0a    /* SIF/DMA Address. -- 0x0a */
  78 #define SIFADX                  0x0c     /* 0x0c */
  79 #define DMALEN                  0x0e    /* SIF DMA length. -- 0x0e */
  80
  81 /*
  82  * POS Registers.  Only for ISA Adapters.
  83  */
  84 #define POSREG                  0x10    /* Adapter Program Option Select (POS)
  85                                          * Register: base IO address + 16 byte.
  86                                          */
  87 #define POSREG_2                24L     /* only for TR4/16+ adapter
  88                                          * base IO address + 24 byte. -- 0x18
  89                                          */
  90
  91 /* SIFCMD command codes (high-low) */
  92 #define CMD_INTERRUPT_ADAPTER   0x8000  /* Cause internal adapter interrupt */
  93 #define CMD_ADAPTER_RESET       0x4000  /* Hardware reset of adapter */
  94 #define CMD_SSB_CLEAR           0x2000  /* Acknowledge to adapter to
  95                                          * system interrupts.
  96                                          */
  97 #define CMD_EXECUTE             0x1000  /* Execute SCB command */
  98 #define CMD_SCB_REQUEST         0x0800  /* Request adapter to interrupt
  99                                          * system when SCB is available for
 100                                          * another command.
 101                                          */
 102 #define CMD_RX_CONTINUE         0x0400  /* Continue receive after odd pointer
 103                                          * stop. (odd pointer receive method)
 104                                          */
 105 #define CMD_RX_VALID            0x0200  /* Now actual RPL is valid. */
 106 #define CMD_TX_VALID            0x0100  /* Now actual TPL is valid. (valid
 107                                          * bit receive/transmit method)
 108                                          */
 109 #define CMD_SYSTEM_IRQ          0x0080  /* Adapter-to-attached-system
 110                                          * interrupt is reset.
 111                                          */
 112 #define CMD_CLEAR_SYSTEM_IRQ    0x0080  /* Clear SYSTEM_INTERRUPT bit.
 113                                          * (write: 1=ignore, 0=reset)
 114                                          */
 115 #define EXEC_SOFT_RESET         0xFF00  /* adapter soft reset. (restart
 116                                          * adapter after hardware reset)
 117                                          */
 118
 119
 120 /* ACL commands (high-low) */
 121 #define ACL_SWHLDA              0x0800  /* Software hold acknowledge. */
 122 #define ACL_SWDDIR              0x0400  /* Data transfer direction. */
 123 #define ACL_SWHRQ               0x0200  /* Pseudo DMA operation. */
 124 #define ACL_PSDMAEN             0x0100  /* Enable pseudo system DMA. */
 125 #define ACL_ARESET              0x0080  /* Adapter hardware reset command.
 126                                          * (held in reset condition as
 127                                          * long as bit is set)
 128                                          */
 129 #define ACL_CPHALT              0x0040  /* Communication processor halt.
 130                                          * (can only be set while ACL_ARESET
 131                                          * bit is set; prevents adapter
 132                                          * processor from executing code while
 133                                          * downloading firmware)
 134                                          */
 135 #define ACL_BOOT                0x0020
 136 #define ACL_SINTEN              0x0008  /* System interrupt enable/disable
 137                                          * (1/0): can be written if ACL_ARESET
 138                                          * is zero.
 139                                          */
 140 #define ACL_PEN                 0x0004
 141
 142 #define ACL_NSELOUT0            0x0002
 143 #define ACL_NSELOUT1            0x0001  /* NSELOUTx have a card-specific
 144                                          * meaning for setting ring speed.
 145                                          */
 146
 147 #define PS_DMA_MASK             (ACL_SWHRQ | ACL_PSDMAEN)
 148
 149
 150 /* SIFSTS register return codes (high-low) */
 151 #define STS_SYSTEM_IRQ          0x0080  /* Adapter-to-attached-system
 152                                          * interrupt is valid.
 153                                          */
 154 #define STS_INITIALIZE          0x0040  /* INITIALIZE status. (ready to
 155                                          * initialize)
 156                                          */
 157 #define STS_TEST                0x0020  /* TEST status. (BUD not completed) */
 158 #define STS_ERROR               0x0010  /* ERROR status. (unrecoverable
 159                                          * HW error occurred)
 160                                          */
 161 #define STS_MASK                0x00F0  /* Mask interesting status bits. */
 162 #define STS_ERROR_MASK          0x000F  /* Get Error Code by masking the
 163                                          * interrupt code bits.
 164                                          */
 165 #define ADAPTER_INT_PTRS        0x0A00  /* Address offset of adapter internal
 166                                          * pointers 01:0a00 (high-low) have to
 167                                          * be read after init and before open.
 168                                          */
 169
 170
 171 /* Interrupt Codes (only MAC IRQs) */
 172 #define STS_IRQ_ADAPTER_CHECK   0x0000  /* unrecoverable hardware or
 173                                          * software error.
 174                                          */
 175 #define STS_IRQ_RING_STATUS     0x0004  /* SSB is updated with ring status. */
 176 #define STS_IRQ_LLC_STATUS      0x0005  /* Not used in MAC-only microcode */
 177 #define STS_IRQ_SCB_CLEAR       0x0006  /* SCB clear, following an
 178                                          * SCB_REQUEST IRQ.
 179                                          */
 180 #define STS_IRQ_TIMER           0x0007  /* Not normally used in MAC ucode */
 181 #define STS_IRQ_COMMAND_STATUS  0x0008  /* SSB is updated with command
 182                                          * status.
 183                                          */
 184 #define STS_IRQ_RECEIVE_STATUS  0x000A  /* SSB is updated with receive
 185                                          * status.
 186                                          */
 187 #define STS_IRQ_TRANSMIT_STATUS 0x000C  /* SSB is updated with transmit
 188                                          * status
 189                                          */
 190 #define STS_IRQ_RECEIVE_PENDING 0x000E  /* Not used in MAC-only microcode */
 191 #define STS_IRQ_MASK            0x000F  /* = STS_ERROR_MASK. */
 192
 193
 194 /* TRANSMIT_STATUS completion code: (SSB.Parm[0]) */
 195 #define COMMAND_COMPLETE        0x0080  /* TRANSMIT command completed
 196                                          * (avoid this!) issue another transmit
 197                                          * to send additional frames.
 198                                          */
 199 #define FRAME_COMPLETE          0x0040  /* Frame has been transmitted;
 200                                          * INTERRUPT_FRAME bit was set in the
 201                                          * CSTAT request; indication of possibly
 202                                          * more than one frame transmissions!
 203                                          * SSB.Parm[0-1]: 32 bit pointer to
 204                                          * TPL of last frame.
 205                                          */
 206 #define LIST_ERROR              0x0020  /* Error in one of the TPLs that
 207                                          * compose the frame; TRANSMIT
 208                                          * terminated; Parm[1-2]: 32bit pointer
 209                                          * to TPL which starts the error
 210                                          * frame; error details in bits 8-13.
 211                                          * (14?)
 212                                          */
 213 #define FRAME_SIZE_ERROR        0x8000  /* FRAME_SIZE does not equal the sum of
 214                                          * the valid DATA_COUNT fields;
 215                                          * FRAME_SIZE less than header plus
 216                                          * information field. (15 bytes +
 217                                          * routing field) Or if FRAME_SIZE
 218                                          * was specified as zero in one list.
 219                                          */
 220 #define TX_THRESHOLD            0x4000  /* FRAME_SIZE greater than (BUFFER_SIZE
 221                                          * - 9) * TX_BUF_MAX.
 222                                          */
 223 #define ODD_ADDRESS             0x2000  /* Odd forward pointer value is
 224                                          * read on a list without END_FRAME
 225                                          * indication.
 226                                          */
 227 #define FRAME_ERROR             0x1000  /* START_FRAME bit (not) anticipated,
 228                                          * but (not) set.
 229                                          */
 230 #define ACCESS_PRIORITY_ERROR   0x0800  /* Access priority requested has not
 231                                          * been allowed.
 232                                          */
 233 #define UNENABLED_MAC_FRAME     0x0400  /* MAC frame has source class of zero
 234                                          * or MAC frame PCF ATTN field is
 235                                          * greater than one.
 236                                          */
 237 #define ILLEGAL_FRAME_FORMAT    0x0200  /* Bit 0 or FC field was set to one. */
 238
 239
 240 /*
 241  * Since we need to support some functions even if the adapter is in a
 242  * CLOSED state, we have a (pseudo-) command queue which holds commands
 243  * that are outstandig to be executed.
 244  *
 245  * Each time a command completes, an interrupt occurs and the next
 246  * command is executed. The command queue is actually a simple word with
 247  * a bit for each outstandig command. Therefore the commands will not be
 248  * executed in the order they have been queued.
 249  *
 250  * The following defines the command code bits and the command queue:
 251  */
 252 #define OC_OPEN                 0x0001  /* OPEN command */
 253 #define OC_TRANSMIT             0x0002  /* TRANSMIT command */
 254 #define OC_TRANSMIT_HALT        0x0004  /* TRANSMIT_HALT command */
 255 #define OC_RECEIVE              0x0008  /* RECEIVE command */
 256 #define OC_CLOSE                0x0010  /* CLOSE command */
 257 #define OC_SET_GROUP_ADDR       0x0020  /* SET_GROUP_ADDR command */
 258 #define OC_SET_FUNCT_ADDR       0x0040  /* SET_FUNCT_ADDR command */
 259 #define OC_READ_ERROR_LOG       0x0080  /* READ_ERROR_LOG command */
 260 #define OC_READ_ADAPTER         0x0100  /* READ_ADAPTER command */
 261 #define OC_MODIFY_OPEN_PARMS    0x0400  /* MODIFY_OPEN_PARMS command */
 262 #define OC_RESTORE_OPEN_PARMS   0x0800  /* RESTORE_OPEN_PARMS command */
 263 #define OC_SET_FIRST_16_GROUP   0x1000  /* SET_FIRST_16_GROUP command */
 264 #define OC_SET_BRIDGE_PARMS     0x2000  /* SET_BRIDGE_PARMS command */
 265 #define OC_CONFIG_BRIDGE_PARMS  0x4000  /* CONFIG_BRIDGE_PARMS command */
 266
 267 #define OPEN                    0x0300  /* C: open command. S: completion. */
 268 #define TRANSMIT                0x0400  /* C: transmit command. S: completion
 269                                          * status. (reject: COMMAND_REJECT if
 270                                          * adapter not opened, TRANSMIT already
 271                                          * issued or address passed in the SCB
 272                                          * not word aligned)
 273                                          */
 274 #define TRANSMIT_HALT           0x0500  /* C: interrupt TX TPL chain; if no
 275                                          * TRANSMIT command issued, the command
 276                                          * is ignored (completion with TRANSMIT
 277                                          * status (0x0400)!)
 278                                          */
 279 #define RECEIVE                 0x0600  /* C: receive command. S: completion
 280                                          * status. (reject: COMMAND_REJECT if
 281                                          * adapter not opened, RECEIVE already
 282                                          * issued or address passed in the SCB
 283                                          * not word aligned)
 284                                          */
 285 #define CLOSE                   0x0700  /* C: close adapter. S: completion.
 286                                          * (COMMAND_REJECT if adapter not open)
 287                                          */
 288 #define SET_GROUP_ADDR          0x0800  /* C: alter adapter group address after
 289                                          * OPEN. S: completion. (COMMAND_REJECT
 290                                          * if adapter not open)
 291                                          */
 292 #define SET_FUNCT_ADDR          0x0900  /* C: alter adapter functional address
 293                                          * after OPEN. S: completion.
 294                                          * (COMMAND_REJECT if adapter not open)
 295                                          */
 296 #define READ_ERROR_LOG          0x0A00  /* C: read adapter error counters.
 297                                          * S: completion. (command ignored
 298                                          * if adapter not open!)
 299                                          */
 300 #define READ_ADAPTER            0x0B00  /* C: read data from adapter memory.
 301                                          * (important: after init and before
 302                                          * open!) S: completion. (ADAPTER_CHECK
 303                                          * interrupt if undefined storage area
 304                                          * read)
 305                                          */
 306 #define MODIFY_OPEN_PARMS       0x0D00  /* C: modify some adapter operational
 307                                          * parameters. (bit correspondend to
 308                                          * WRAP_INTERFACE is ignored)
 309                                          * S: completion. (reject:
 310                                          * COMMAND_REJECT)
 311                                          */
 312 #define RESTORE_OPEN_PARMS      0x0E00  /* C: modify some adapter operational
 313                                          * parameters. (bit correspondend
 314                                          * to WRAP_INTERFACE is ignored)
 315                                          * S: completion. (reject:
 316                                          * COMMAND_REJECT)
 317                                          */
 318 #define SET_FIRST_16_GROUP      0x0F00  /* C: alter the first two bytes in
 319                                          * adapter group address.
 320                                          * S: completion. (reject:
 321                                          * COMMAND_REJECT)
 322                                          */
 323 #define SET_BRIDGE_PARMS        0x1000  /* C: values and conditions for the
 324                                          * adapter hardware to use when frames
 325                                          * are copied for forwarding.
 326                                          * S: completion. (reject:
 327                                          * COMMAND_REJECT)
 328                                          */
 329 #define CONFIG_BRIDGE_PARMS     0x1100  /* C: ..
 330                                          * S: completion. (reject:
 331                                          * COMMAND_REJECT)
 332                                          */
 333
 334 #define SPEED_4                 4
 335 #define SPEED_16                16      /* Default transmission speed  */
 336
 337
 338 /* Initialization Parameter Block (IPB); word alignment necessary! */
 339 #define BURST_SIZE      0x0018  /* Default burst size */
 340 #define BURST_MODE      0x9F00  /* Burst mode enable */
 341 #define DMA_RETRIES     0x0505  /* Magic DMA retry number... */
 342
 343 #define CYCLE_TIME      3       /* Default AT-bus cycle time: 500 ns
 344                                  * (later adapter version: fix  cycle time!)
 345                                  */
 346 #define LINE_SPEED_BIT  0x80
 347
 348 /* Macro definition for the wait function. */
 349 #define ONE_SECOND_TICKS        1000000
 350 #define HALF_SECOND             (ONE_SECOND_TICKS / 2)
 351 #define ONE_SECOND              (ONE_SECOND_TICKS)
 352 #define TWO_SECONDS             (ONE_SECOND_TICKS * 2)
 353 #define THREE_SECONDS           (ONE_SECOND_TICKS * 3)
 354 #define FOUR_SECONDS            (ONE_SECOND_TICKS * 4)
 355 #define FIVE_SECONDS            (ONE_SECOND_TICKS * 5)
 356
 357 #define BUFFER_SIZE             2048    /* Buffers on Adapter */
 358
 359 #pragma pack(1)
 360 typedef struct {
 361         unsigned short Init_Options;    /* Initialize with burst mode;
 362                                          * LLC disabled. (MAC only)
 363                                          */
 364
 365         /* Interrupt vectors the adapter places on attached system bus. */
 366         u_int8_t  CMD_Status_IV;    /* Interrupt vector: command status. */
 367         u_int8_t  TX_IV;            /* Interrupt vector: transmit. */
 368         u_int8_t  RX_IV;            /* Interrupt vector: receive. */
 369         u_int8_t  Ring_Status_IV;   /* Interrupt vector: ring status. */
 370         u_int8_t  SCB_Clear_IV;     /* Interrupt vector: SCB clear. */
 371         u_int8_t  Adapter_CHK_IV;   /* Interrupt vector: adapter check. */
 372
 373         u_int16_t RX_Burst_Size;    /* Max. number of transfer cycles. */
 374         u_int16_t TX_Burst_Size;    /* During DMA burst; even value! */
 375         u_int16_t DMA_Abort_Thrhld; /* Number of DMA retries. */
 376
 377         u_int32_t SCB_Addr;   /* SCB address: even, word aligned, high-low */
 378         u_int32_t SSB_Addr;   /* SSB address: even, word aligned, high-low */
 379 } IPB, *IPB_Ptr;
 380 #pragma pack()
 381
 382 /*
 383  * OPEN Command Parameter List (OCPL) (can be reused, if the adapter has to
 384  * be reopened)
 385  */
 386 #define BUFFER_SIZE     2048            /* Buffers on Adapter. */
 387 #define TPL_SIZE        8+6*TX_FRAG_NUM /* Depending on fragments per TPL. */
 388 #define RPL_SIZE        14              /* (with TI firmware v2.26 handling
 389                                          * up to nine fragments possible)
 390                                          */
 391 #define TX_BUF_MIN      20              /* ??? (Stephan: calculation with */
 392 #define TX_BUF_MAX      40              /* BUFFER_SIZE and MAX_FRAME_SIZE) ???
 393                                          */
 394 #define DISABLE_EARLY_TOKEN_RELEASE     0x1000
 395
 396 /* OPEN Options (high-low) */
 397 #define WRAP_INTERFACE          0x0080  /* Inserting omitted for test
 398                                          * purposes; transmit data appears
 399                                          * as receive data. (useful for
 400                                          * testing; change: CLOSE necessary)
 401                                          */
 402 #define DISABLE_HARD_ERROR      0x0040  /* On HARD_ERROR & TRANSMIT_BEACON
 403                                          * no RING.STATUS interrupt.
 404                                          */
 405 #define DISABLE_SOFT_ERROR      0x0020  /* On SOFT_ERROR, no RING.STATUS
 406                                          * interrupt.
 407                                          */
 408 #define PASS_ADAPTER_MAC_FRAMES 0x0010  /* Passing unsupported MAC frames
 409                                          * to system.
 410                                          */
 411 #define PASS_ATTENTION_FRAMES   0x0008  /* All changed attention MAC frames are
 412                                          * passed to the system.
 413                                          */
 414 #define PAD_ROUTING_FIELD       0x0004  /* Routing field is padded to 18
 415                                          * bytes.
 416                                          */
 417 #define FRAME_HOLD              0x0002  /*Adapter waits for entire frame before
 418                                          * initiating DMA transfer; otherwise:
 419                                          * DMA transfer initiation if internal
 420                                          * buffer filled.
 421                                          */
 422 #define CONTENDER               0x0001  /* Adapter participates in the monitor
 423                                          * contention process.
 424                                          */
 425 #define PASS_BEACON_MAC_FRAMES  0x8000  /* Adapter passes beacon MAC frames
 426                                          * to the system.
 427                                          */
 428 #define EARLY_TOKEN_RELEASE     0x1000  /* Only valid in 16 Mbps operation;
 429                                          * 0 = ETR. (no effect in 4 Mbps
 430                                          * operation)
 431                                          */
 432 #define COPY_ALL_MAC_FRAMES     0x0400  /* All MAC frames are copied to
 433                                          * the system. (after OPEN: duplicate
 434                                          * address test (DAT) MAC frame is
 435                                          * first received frame copied to the
 436                                          * system)
 437                                          */
 438 #define COPY_ALL_NON_MAC_FRAMES 0x0200  /* All non MAC frames are copied to
 439                                          * the system.
 440                                          */
 441 #define PASS_FIRST_BUF_ONLY     0x0100  /* Passes only first internal buffer
 442                                          * of each received frame; FrameSize
 443                                          * of RPLs must contain internal
 444                                          * BUFFER_SIZE bits for promiscous mode.
 445                                          */
 446 #define ENABLE_FULL_DUPLEX_SELECTION    0x2000
 447                                         /* Enable the use of full-duplex
 448                                          * settings with bits in byte 22 in
 449                                          * ocpl. (new feature in firmware
 450                                          * version 3.09)
 451                                          */
 452
 453 /* Full-duplex settings */
 454 #define OPEN_FULL_DUPLEX_OFF    0x0000
 455 #define OPEN_FULL_DUPLEX_ON     0x00c0
 456 #define OPEN_FULL_DUPLEX_AUTO   0x0080
 457
 458 #define PROD_ID_SIZE    18      /* Length of product ID. */
 459
 460 #define TX_FRAG_NUM     3        /* Number of fragments used in one TPL. */
 461 #define TX_MORE_FRAGMENTS 0x8000 /* Bit set in DataCount to indicate more
 462                                   * fragments following.
 463                                   */
 464
 465 /* XXX is there some better way to do this? */
 466 #define ISA_MAX_ADDRESS         0x00ffffff
 467 #define PCI_MAX_ADDRESS         0xffffffff
 468
 469 #pragma pack(1)
 470 typedef struct {
 471         u_int16_t OPENOptions;
 472         u_int8_t  NodeAddr[6];  /* Adapter node address; use ROM
 473                                  * address
 474                                  */
 475         u_int32_t GroupAddr;    /* Multicast: high order
 476                                  * bytes = 0xC000
 477                                  */
 478         u_int32_t FunctAddr;    /* High order bytes = 0xC000 */
 479         u_int16_t RxListSize;   /* RPL size: 0 (=26), 14, 20 or
 480                                  * 26 bytes read by the adapter.
 481                                  * (Depending on the number of
 482                                  * fragments/list)
 483                                  */
 484         u_int16_t TxListSize;   /* TPL size */
 485         u_int16_t BufSize;      /* Is automatically rounded up to the
 486                                  * nearest nK boundary.
 487                                  */
 488         u_int16_t FullDuplex;
 489         u_int16_t Reserved;
 490         u_int8_t  TXBufMin;     /* Number of adapter buffers reserved
 491                                  * for transmission a minimum of 2
 492                                  * buffers must be allocated.
 493                                  */
 494         u_int8_t  TXBufMax;     /* Maximum number of adapter buffers
 495                                  * for transmit; a minimum of 2 buffers
 496                                  * must be available for receive.
 497                                  * Default: 6
 498                                  */
 499         u_int16_t ProdIDAddr[2];/* Pointer to product ID. */
 500 } OPB, *OPB_Ptr;
 501 #pragma pack()
 502
 503 /*
 504  * SCB: adapter commands enabled by the host system started by writing
 505  * CMD_INTERRUPT_ADAPTER | CMD_EXECUTE (|SCB_REQUEST) to the SIFCMD IO
 506  * register. (special case: | CMD_SYSTEM_IRQ for initialization)
 507  */
 508 #pragma pack(1)
 509 typedef struct {
 510         u_int16_t CMD;          /* Command code */
 511         u_int16_t Parm[2];      /* Pointer to Command Parameter Block */
 512 } SCB;  /* System Command Block (32 bit physical address; big endian)*/
 513 #pragma pack()
 514
 515 /*
 516  * SSB: adapter command return status can be evaluated after COMMAND_STATUS
 517  * adapter to system interrupt after reading SSB, the availability of the SSB
 518  * has to be told the adapter by writing CMD_INTERRUPT_ADAPTER | CMD_SSB_CLEAR
 519  * in the SIFCMD IO register.
 520  */
 521 #pragma pack(1)
 522 typedef struct {
 523         u_int16_t STS;          /* Status code */
 524         u_int16_t Parm[3];      /* Parameter or pointer to Status Parameter
 525                                  * Block.
 526                                  */
 527 } SSB;  /* System Status Block (big endian - physical address)  */
 528 #pragma pack()
 529
 530 typedef struct {
 531         unsigned short BurnedInAddrPtr; /* Pointer to adapter burned in
 532                                          * address. (BIA)
 533                                          */
 534         unsigned short SoftwareLevelPtr;/* Pointer to software level data. */
 535         unsigned short AdapterAddrPtr;  /* Pointer to adapter addresses. */
 536         unsigned short AdapterParmsPtr; /* Pointer to adapter parameters. */
 537         unsigned short MACBufferPtr;    /* Pointer to MAC buffer. (internal) */
 538         unsigned short LLCCountersPtr;  /* Pointer to LLC counters.  */
 539         unsigned short SpeedFlagPtr;    /* Pointer to data rate flag.
 540                                          * (4/16 Mbps)
 541                                          */
 542         unsigned short AdapterRAMPtr;   /* Pointer to adapter RAM found. (KB) */
 543 } INTPTRS;      /* Adapter internal pointers */
 544
 545 #pragma pack(1)
 546 typedef struct {
 547         u_int8_t  Line_Error;           /* Line error: code violation in
 548                                          * frame or in a token, or FCS error.
 549                                          */
 550         u_int8_t  Internal_Error;       /* IBM specific. (Reserved_1) */
 551         u_int8_t  Burst_Error;
 552         u_int8_t  ARI_FCI_Error;        /* ARI/FCI bit zero in AMP or
 553                                          * SMP MAC frame.
 554                                          */
 555         u_int8_t  AbortDelimeters;      /* IBM specific. (Reserved_2) */
 556         u_int8_t  Reserved_3;
 557         u_int8_t  Lost_Frame_Error;     /* Receive of end of transmitted
 558                                          * frame failed.
 559                                          */
 560         u_int8_t  Rx_Congest_Error;     /* Adapter in repeat mode has not
 561                                          * enough buffer space to copy incoming
 562                                          * frame.
 563                                          */
 564         u_int8_t  Frame_Copied_Error;   /* ARI bit not zero in frame
 565                                          * addressed to adapter.
 566                                          */
 567         u_int8_t  Frequency_Error;      /* IBM specific. (Reserved_4) */
 568         u_int8_t  Token_Error;          /* (active only in monitor station) */
 569         u_int8_t  Reserved_5;
 570         u_int8_t  DMA_Bus_Error;        /* DMA bus errors not exceeding the
 571                                          * abort thresholds.
 572                                          */
 573         u_int8_t  DMA_Parity_Error;     /* DMA parity errors not exceeding
 574                                          * the abort thresholds.
 575                                          */
 576 } ERRORTAB;     /* Adapter error counters */
 577 #pragma pack()
 578
 579
 580 /*--------------------- Send and Receive definitions -------------------*/
 581 #pragma pack(1)
 582 typedef struct {
 583         u_int16_t DataCount;    /* Value 0, even and odd values are
 584                                  * permitted; value is unaltered most
 585                                  * significant bit set: following
 586                                  * fragments last fragment: most
 587                                  * significant bit is not evaluated.
 588                                  * (???)
 589                                  */
 590         u_int32_t DataAddr;     /* Pointer to frame data fragment;
 591                                  * even or odd.
 592                                  */
 593 } Fragment;
 594 #pragma pack()
 595
 596 #define MAX_FRAG_NUMBERS    9   /* Maximal number of fragments possible to use
 597                                  * in one RPL/TPL. (depending on TI firmware
 598                                  * version)
 599                                  */
 600
 601 /*
 602  * AC (1), FC (1), Dst (6), Src (6), RIF (18), Data (4472) = 4504
 603  * The packet size can be one of the follows: 548, 1502, 2084, 4504, 8176,
 604  * 11439, 17832. Refer to TMS380 Second Generation Token Ring User's Guide
 605  * Page 2-27.
 606  */
 607 #define HEADER_SIZE             (1 + 1 + 6 + 6)
 608 #define SRC_SIZE                18
 609 #define MIN_DATA_SIZE           516
 610 #define DEFAULT_DATA_SIZE       4472
 611 #define MAX_DATA_SIZE           17800
 612
 613 #define DEFAULT_PACKET_SIZE (HEADER_SIZE + SRC_SIZE + DEFAULT_DATA_SIZE)
 614 #define MIN_PACKET_SIZE     (HEADER_SIZE + SRC_SIZE + MIN_DATA_SIZE)
 615 #define MAX_PACKET_SIZE     (HEADER_SIZE + SRC_SIZE + MAX_DATA_SIZE)
 616
 617 /*
 618  * Macros to deal with the frame status field.
 619  */
 620 #define AC_NOT_RECOGNIZED       0x00
 621 #define GROUP_BIT               0x80
 622 #define GET_TRANSMIT_STATUS_HIGH_BYTE(Ts) ((unsigned char)((Ts) >> 8))
 623 #define GET_FRAME_STATUS_HIGH_AC(Fs)      ((unsigned char)(((Fs) & 0xC0) >> 6))
 624 #define GET_FRAME_STATUS_LOW_AC(Fs)       ((unsigned char)(((Fs) & 0x0C) >> 2))
 625 #define DIRECTED_FRAME(Context)           (!((Context)->MData[2] & GROUP_BIT))
 626
 627
 628 /*--------------------- Send Functions ---------------------------------*/
 629 /* define TX_CSTAT _REQUEST (R) and _COMPLETE (C) values (high-low) */
 630
 631 #define TX_VALID                0x0080  /* R: set via TRANSMIT.VALID interrupt.
 632                                          * C: always reset to zero!
 633                                          */
 634 #define TX_FRAME_COMPLETE       0x0040  /* R: must be reset to zero.
 635                                          * C: set to one.
 636                                          */
 637 #define TX_START_FRAME          0x0020  /* R: start of a frame: 1
 638                                          * C: unchanged.
 639                                          */
 640 #define TX_END_FRAME            0x0010  /* R: end of a frame: 1
 641                                          * C: unchanged.
 642                                          */
 643 #define TX_FRAME_IRQ            0x0008  /* R: request interrupt generation
 644                                          * after transmission.
 645                                          * C: unchanged.
 646                                          */
 647 #define TX_ERROR                0x0004  /* R: reserved.
 648                                          * C: set to one if Error occurred.
 649                                          */
 650 #define TX_INTERFRAME_WAIT      0x0004
 651 #define TX_PASS_CRC             0x0002  /* R: set if CRC value is already
 652                                          * calculated. (valid only in
 653                                          * FRAME_START TPL)
 654                                          * C: unchanged.
 655                                          */
 656 #define TX_PASS_SRC_ADDR        0x0001  /* R: adapter uses explicit frame
 657                                          * source address and does not overwrite
 658                                          * with the adapter node address.
 659                                          * (valid only in FRAME_START TPL)
 660                                          *
 661                                          * C: unchanged.
 662                                          */
 663 #define TX_STRIP_FS             0xFF00  /* R: reserved.
 664                                          * C: if no Transmission Error,
 665                                          * field contains copy of FS byte after
 666                                          * stripping of frame.
 667                                          */
 668
 669 /*
 670  * Structure of Transmit Parameter Lists (TPLs) (only one frame every TPL,
 671  * but possibly multiple TPLs for one frame) the length of the TPLs has to be
 672  * initialized in the OPL. (OPEN parameter list)
 673  */
 674 #define TPL_NUM         3       /* Number of Transmit Parameter Lists.
 675                                  * !! MUST BE >= 3 !!
 676                                  */
 677
 678 #pragma pack(1)
 679 typedef struct s_TPL TPL;
 680
 681 struct s_TPL {  /* Transmit Parameter List (align on even word boundaries) */
 682         u_int32_t NextTPLAddr;          /* Pointer to next TPL in chain; if
 683                                          * pointer is odd: this is the last
 684                                          * TPL. Pointing to itself can cause
 685                                          * problems!
 686                                          */
 687         volatile u_int16_t Status;      /* Initialized by the adapter:
 688                                          * CSTAT_REQUEST important: update least
 689                                          * significant bit first! Set by the
 690                                          * adapter: CSTAT_COMPLETE status.
 691                                          */
 692         u_int16_t FrameSize;            /* Number of bytes to be transmitted
 693                                          * as a frame including AC/FC,
 694                                          * Destination, Source, Routing field
 695                                          * not including CRC, FS, End Delimiter
 696                                          * (valid only if START_FRAME bit in
 697                                          * CSTAT nonzero) must not be zero in
 698                                          * any list; maximum value: (BUFFER_SIZE
 699                                          * - 8) * TX_BUF_MAX sum of DataCount
 700                                          * values in FragmentList must equal
 701                                          * Frame_Size value in START_FRAME TPL!
 702                                          * frame data fragment list.
 703                                          */
 704
 705         /* TPL/RPL size in OPEN parameter list depending on maximal
 706          * numbers of fragments used in one parameter list.
 707          */
 708         Fragment FragList[TX_FRAG_NUM]; /* Maximum: nine frame fragments in one
 709                                          * TPL actual version of firmware: 9
 710                                          * fragments possible.
 711                                          */
 712 #pragma pack()
 713
 714         /* Special proprietary data and precalculations */
 715
 716         TPL *NextTPLPtr;                /* Pointer to next TPL in chain. */
 717         unsigned char *MData;
 718         struct sk_buff *Skb;
 719         unsigned char TPLIndex;
 720         volatile unsigned char BusyFlag;/* Flag: TPL busy? */
 721         dma_addr_t DMABuff;             /* DMA IO bus address from dma_map */
 722 };
 723
 724 /* ---------------------Receive Functions-------------------------------*
 725  * define RECEIVE_CSTAT_REQUEST (R) and RECEIVE_CSTAT_COMPLETE (C) values.
 726  * (high-low)
 727  */
 728 #define RX_VALID                0x0080  /* R: set; tell adapter with
 729                                          * RECEIVE.VALID interrupt.
 730                                          * C: reset to zero.
 731                                          */
 732 #define RX_FRAME_COMPLETE       0x0040  /* R: must be reset to zero,
 733                                          * C: set to one.
 734                                          */
 735 #define RX_START_FRAME          0x0020  /* R: must be reset to zero.
 736                                          * C: set to one on the list.
 737                                          */
 738 #define RX_END_FRAME            0x0010  /* R: must be reset to zero.
 739                                          * C: set to one on the list
 740                                          * that ends the frame.
 741                                          */
 742 #define RX_FRAME_IRQ            0x0008  /* R: request interrupt generation
 743                                          * after receive.
 744                                          * C: unchanged.
 745                                          */
 746 #define RX_INTERFRAME_WAIT      0x0004  /* R: after receiving a frame:
 747                                          * interrupt and wait for a
 748                                          * RECEIVE.CONTINUE.
 749                                          * C: unchanged.
 750                                          */
 751 #define RX_PASS_CRC             0x0002  /* R: if set, the adapter includes
 752                                          * the CRC in data passed. (last four
 753                                          * bytes; valid only if FRAME_START is
 754                                          * set)
 755                                          * C: set, if CRC is included in
 756                                          * received data.
 757                                          */
 758 #define RX_PASS_SRC_ADDR        0x0001  /* R: adapter uses explicit frame
 759                                          * source address and does not
 760                                          * overwrite with the adapter node
 761                                          * address. (valid only if FRAME_START
 762                                          * is set)
 763                                          * C: unchanged.
 764                                          */
 765 #define RX_RECEIVE_FS           0xFC00  /* R: reserved; must be reset to zero.
 766                                          * C: on lists with START_FRAME, field
 767                                          * contains frame status field from
 768                                          * received frame; otherwise cleared.
 769                                          */
 770 #define RX_ADDR_MATCH           0x0300  /* R: reserved; must be reset to zero.
 771                                          * C: address match code mask.
 772                                          */
 773 #define RX_STATUS_MASK          0x00FF  /* Mask for receive status bits. */
 774
 775 #define RX_INTERN_ADDR_MATCH    0x0100  /* C: internally address match. */
 776 #define RX_EXTERN_ADDR_MATCH    0x0200  /* C: externally matched via
 777                                          * XMATCH/XFAIL interface.
 778                                          */
 779 #define RX_INTEXT_ADDR_MATCH    0x0300  /* C: internally and externally
 780                                          * matched.
 781                                          */
 782 #define RX_READY (RX_VALID | RX_FRAME_IRQ) /* Ready for receive. */
 783
 784 /* Constants for Command Status Interrupt.
 785  * COMMAND_REJECT status field bit functions (SSB.Parm[0])
 786  */
 787 #define ILLEGAL_COMMAND         0x0080  /* Set if an unknown command
 788                                          * is issued to the adapter
 789                                          */
 790 #define ADDRESS_ERROR           0x0040  /* Set if any address field in
 791                                          * the SCB is odd. (not word aligned)
 792                                          */
 793 #define ADAPTER_OPEN            0x0020  /* Command issued illegal with
 794                                          * open adapter.
 795                                          */
 796 #define ADAPTER_CLOSE           0x0010  /* Command issued illegal with
 797                                          * closed adapter.
 798                                          */
 799 #define SAME_COMMAND            0x0008  /* Command issued with same command
 800                                          * already executing.
 801                                          */
 802
 803 /* OPEN_COMPLETION values (SSB.Parm[0], MSB) */
 804 #define NODE_ADDR_ERROR         0x0040  /* Wrong address or BIA read
 805                                          * zero address.
 806                                          */
 807 #define LIST_SIZE_ERROR         0x0020  /* If List_Size value not in 0,
 808                                          * 14, 20, 26.
 809                                          */
 810 #define BUF_SIZE_ERROR          0x0010  /* Not enough available memory for
 811                                          * two buffers.
 812                                          */
 813 #define TX_BUF_COUNT_ERROR      0x0004  /* Remaining receive buffers less than
 814                                          * two.
 815                                          */
 816 #define OPEN_ERROR              0x0002  /* Error during ring insertion; more
 817                                          * information in bits 8-15.
 818                                          */
 819
 820 /* Standard return codes */
 821 #define GOOD_COMPLETION         0x0080  /* =OPEN_SUCCESSFULL */
 822 #define INVALID_OPEN_OPTION     0x0001  /* OPEN options are not supported by
 823                                          * the adapter.
 824                                          */
 825
 826 /* OPEN phases; details of OPEN_ERROR (SSB.Parm[0], LSB)            */
 827 #define OPEN_PHASES_MASK            0xF000  /* Check only the bits 8-11. */
 828 #define LOBE_MEDIA_TEST             0x1000
 829 #define PHYSICAL_INSERTION          0x2000
 830 #define ADDRESS_VERIFICATION        0x3000
 831 #define PARTICIPATION_IN_RING_POLL  0x4000
 832 #define REQUEST_INITIALISATION      0x5000
 833 #define FULLDUPLEX_CHECK            0x6000
 834
 835 /* OPEN error codes; details of OPEN_ERROR (SSB.Parm[0], LSB) */
 836 #define OPEN_ERROR_CODES_MASK   0x0F00  /* Check only the bits 12-15. */
 837 #define OPEN_FUNCTION_FAILURE   0x0100  /* Unable to transmit to itself or
 838                                          * frames received before insertion.
 839                                          */
 840 #define OPEN_SIGNAL_LOSS        0x0200  /* Signal loss condition detected at
 841                                          * receiver.
 842                                          */
 843 #define OPEN_TIMEOUT            0x0500  /* Insertion timer expired before
 844                                          * logical insertion.
 845                                          */
 846 #define OPEN_RING_FAILURE       0x0600  /* Unable to receive own ring purge
 847                                          * MAC frames.
 848                                          */
 849 #define OPEN_RING_BEACONING     0x0700  /* Beacon MAC frame received after
 850                                          * ring insertion.
 851                                          */
 852 #define OPEN_DUPLICATE_NODEADDR 0x0800  /* Other station in ring found
 853                                          * with the same address.
 854                                          */
 855 #define OPEN_REQUEST_INIT       0x0900  /* RPS present but does not respond. */
 856 #define OPEN_REMOVE_RECEIVED    0x0A00  /* Adapter received a remove adapter
 857                                          * MAC frame.
 858                                          */
 859 #define OPEN_FULLDUPLEX_SET     0x0D00  /* Got this with full duplex on when
 860                                          * trying to connect to a normal ring.
 861                                          */
 862
 863 /* SET_BRIDGE_PARMS return codes: */
 864 #define BRIDGE_INVALID_MAX_LEN  0x4000  /* MAX_ROUTING_FIELD_LENGTH odd,
 865                                          * less than 6 or > 30.
 866                                          */
 867 #define BRIDGE_INVALID_SRC_RING 0x2000  /* SOURCE_RING number zero, too large
 868                                          * or = TARGET_RING.
 869                                          */
 870 #define BRIDGE_INVALID_TRG_RING 0x1000  /* TARGET_RING number zero, too large
 871                                          * or = SOURCE_RING.
 872                                          */
 873 #define BRIDGE_INVALID_BRDGE_NO 0x0800  /* BRIDGE_NUMBER too large. */
 874 #define BRIDGE_INVALID_OPTIONS  0x0400  /* Invalid bridge options. */
 875 #define BRIDGE_DIAGS_FAILED     0x0200  /* Diagnostics of TMS380SRA failed. */
 876 #define BRIDGE_NO_SRA           0x0100  /* The TMS380SRA does not exist in HW
 877                                          * configuration.
 878                                          */
 879
 880 /*
 881  * Bring Up Diagnostics error codes.
 882  */
 883 #define BUD_INITIAL_ERROR       0x0
 884 #define BUD_CHECKSUM_ERROR      0x1
 885 #define BUD_ADAPTER_RAM_ERROR   0x2
 886 #define BUD_INSTRUCTION_ERROR   0x3
 887 #define BUD_CONTEXT_ERROR       0x4
 888 #define BUD_PROTOCOL_ERROR      0x5
 889 #define BUD_INTERFACE_ERROR     0x6
 890
 891 /* BUD constants */
 892 #define BUD_MAX_RETRIES         3
 893 #define BUD_MAX_LOOPCNT         6
 894 #define BUD_TIMEOUT             3000
 895
 896 /* Initialization constants */
 897 #define INIT_MAX_RETRIES        3       /* Maximum three retries. */
 898 #define INIT_MAX_LOOPCNT        22      /* Maximum loop counts. */
 899
 900 /* RING STATUS field values (high/low) */
 901 #define SIGNAL_LOSS             0x0080  /* Loss of signal on the ring
 902                                          * detected.
 903                                          */
 904 #define HARD_ERROR              0x0040  /* Transmitting or receiving beacon
 905                                          * frames.
 906                                          */
 907 #define SOFT_ERROR              0x0020  /* Report error MAC frame
 908                                          * transmitted.
 909                                          */
 910 #define TRANSMIT_BEACON         0x0010  /* Transmitting beacon frames on the
 911                                          * ring.
 912                                          */
 913 #define LOBE_WIRE_FAULT         0x0008  /* Open or short circuit in the
 914                                          * cable to concentrator; adapter
 915                                          * closed.
 916                                          */
 917 #define AUTO_REMOVAL_ERROR      0x0004  /* Lobe wrap test failed, deinserted;
 918                                          * adapter closed.
 919                                          */
 920 #define REMOVE_RECEIVED         0x0001  /* Received a remove ring station MAC
 921                                          * MAC frame request; adapter closed.
 922                                          */
 923 #define COUNTER_OVERFLOW        0x8000  /* Overflow of one of the adapters
 924                                          * error counters; READ.ERROR.LOG.
 925                                          */
 926 #define SINGLE_STATION          0x4000  /* Adapter is the only station on the
 927                                          * ring.
 928                                          */
 929 #define RING_RECOVERY           0x2000  /* Claim token MAC frames on the ring;
 930                                          * reset after ring purge frame.
 931                                          */
 932
 933 #define ADAPTER_CLOSED (LOBE_WIRE_FAULT | AUTO_REMOVAL_ERROR |\
 934                         REMOVE_RECEIVED)
 935
 936 /* Adapter_check_block.Status field bit assignments: */
 937 #define DIO_PARITY              0x8000  /* Adapter detects bad parity
 938                                          * through direct I/O access.
 939                                          */
 940 #define DMA_READ_ABORT          0x4000  /* Aborting DMA read operation
 941                                          * from system Parm[0]: 0=timeout,
 942                                          * 1=parity error, 2=bus error;
 943                                          * Parm[1]: 32 bit pointer to host
 944                                          * system address at failure.
 945                                          */
 946 #define DMA_WRITE_ABORT         0x2000  /* Aborting DMA write operation
 947                                          * to system. (parameters analogous to
 948                                          * DMA_READ_ABORT)
 949                                          */
 950 #define ILLEGAL_OP_CODE         0x1000  /* Illegal operation code in the
 951                                          * the adapters firmware Parm[0]-2:
 952                                          * communications processor registers
 953                                          * R13-R15.
 954                                          */
 955 #define PARITY_ERRORS           0x0800  /* Adapter detects internal bus
 956                                          * parity error.
 957                                          */
 958 #define RAM_DATA_ERROR          0x0080  /* Valid only during RAM testing;
 959                                          * RAM data error Parm[0-1]: 32 bit
 960                                          * pointer to RAM location.
 961                                          */
 962 #define RAM_PARITY_ERROR        0x0040  /* Valid only during RAM testing;
 963                                          * RAM parity error Parm[0-1]: 32 bit
 964                                          * pointer to RAM location.
 965                                          */
 966 #define RING_UNDERRUN           0x0020  /* Internal DMA underrun when
 967                                          * transmitting onto ring.
 968                                          */
 969 #define INVALID_IRQ             0x0008  /* Unrecognized interrupt generated
 970                                          * internal to adapter Parm[0-2]:
 971                                          * adapter register R13-R15.
 972                                          */
 973 #define INVALID_ERROR_IRQ       0x0004  /* Unrecognized error interrupt
 974                                          * generated Parm[0-2]: adapter register
 975                                          * R13-R15.
 976                                          */
 977 #define INVALID_XOP             0x0002  /* Unrecognized XOP request in
 978                                          * communication processor Parm[0-2]:
 979                                          * adapter register R13-R15.
 980                                          */
 981 #define CHECKADDR               0x05E0  /* Adapter check status information
 982                                          * address offset.
 983                                          */
 984 #define ROM_PAGE_0              0x0000  /* Adapter ROM page 0. */
 985
 986 /*
 987  * RECEIVE.STATUS interrupt result SSB values: (high-low)
 988  * (RECEIVE_COMPLETE field bit definitions in SSB.Parm[0])
 989  */
 990 #define RX_COMPLETE             0x0080  /* SSB.Parm[0]; SSB.Parm[1]: 32
 991                                          * bit pointer to last RPL.
 992                                          */
 993 #define RX_SUSPENDED            0x0040  /* SSB.Parm[0]; SSB.Parm[1]: 32
 994                                          * bit pointer to RPL with odd
 995                                          * forward pointer.
 996                                          */
 997
 998 /* Valid receive CSTAT: */
 999 #define RX_FRAME_CONTROL_BITS (RX_VALID | RX_START_FRAME | RX_END_FRAME | \
1000                                RX_FRAME_COMPLETE)
1001 #define VALID_SINGLE_BUFFER_FRAME (RX_START_FRAME | RX_END_FRAME | \
1002                                    RX_FRAME_COMPLETE)
1003
1004 typedef enum SKB_STAT SKB_STAT;
1005 enum SKB_STAT {
1006         SKB_UNAVAILABLE,
1007         SKB_DMA_DIRECT,
1008         SKB_DATA_COPY
1009 };
1010
1011 /* Receive Parameter List (RPL) The length of the RPLs has to be initialized
1012  * in the OPL. (OPEN parameter list)
1013  */
1014 #define RPL_NUM         3
1015
1016 #define RX_FRAG_NUM     1       /* Maximal number of used fragments in one RPL.
1017                                  * (up to firmware v2.24: 3, now: up to 9)
1018                                  */
1019
1020 #pragma pack(1)
1021 typedef struct s_RPL RPL;
1022 struct s_RPL {  /* Receive Parameter List */
1023         u_int32_t NextRPLAddr;          /* Pointer to next RPL in chain
1024                                          * (normalized = physical 32 bit
1025                                          * address) if pointer is odd: this
1026                                          * is last RPL. Pointing to itself can
1027                                          * cause problems!
1028                                          */
1029         volatile u_int16_t Status;      /* Set by creation of Receive Parameter
1030                                          * List RECEIVE_CSTAT_COMPLETE set by
1031                                          * adapter in lists that start or end
1032                                          * a frame.
1033                                          */
1034         volatile u_int16_t FrameSize;    /* Number of bytes received as a
1035                                          * frame including AC/FC, Destination,
1036                                          * Source, Routing field not including
1037                                          * CRC, FS (Frame Status), End Delimiter
1038                                          * (valid only if START_FRAME bit in
1039                                          * CSTAT nonzero) must not be zero in
1040                                          * any list; maximum value: (BUFFER_SIZE
1041                                          * - 8) * TX_BUF_MAX sum of DataCount
1042                                          * values in FragmentList must equal
1043                                          * Frame_Size value in START_FRAME TPL!
1044                                          * frame data fragment list
1045                                          */
1046
1047         /* TPL/RPL size in OPEN parameter list depending on maximal numbers
1048          * of fragments used in one parameter list.
1049          */
1050         Fragment FragList[RX_FRAG_NUM]; /* Maximum: nine frame fragments in
1051                                          * one TPL. Actual version of firmware:
1052                                          * 9 fragments possible.
1053                                          */
1054 #pragma pack()
1055
1056         /* Special proprietary data and precalculations. */
1057         RPL *NextRPLPtr;        /* Logical pointer to next RPL in chain. */
1058         unsigned char *MData;
1059         struct sk_buff *Skb;
1060         SKB_STAT SkbStat;
1061         int RPLIndex;
1062         dma_addr_t DMABuff;             /* DMA IO bus address from dma_map */
1063 };
1064
1065 /* Information that need to be kept for each board. */
1066 typedef struct net_local {
1067 #pragma pack(1)
1068         IPB ipb;        /* Initialization Parameter Block. */
1069         SCB scb;        /* System Command Block: system to adapter
1070                          * communication.
1071                          */
1072         SSB ssb;        /* System Status Block: adapter to system
1073                          * communication.
1074                          */
1075         OPB ocpl;       /* Open Options Parameter Block. */
1076
1077         ERRORTAB errorlogtable; /* Adapter statistic error counters.
1078                                  * (read from adapter memory)
1079                                  */
1080         unsigned char ProductID[PROD_ID_SIZE + 1]; /* Product ID */
1081 #pragma pack()
1082
1083         TPL Tpl[TPL_NUM];
1084         TPL *TplFree;
1085         TPL *TplBusy;
1086         unsigned char LocalTxBuffers[TPL_NUM][DEFAULT_PACKET_SIZE];
1087
1088         RPL Rpl[RPL_NUM];
1089         RPL *RplHead;
1090         RPL *RplTail;
1091         unsigned char LocalRxBuffers[RPL_NUM][DEFAULT_PACKET_SIZE];
1092
1093         struct device *pdev;
1094         int DataRate;
1095         unsigned char ScbInUse;
1096         unsigned short CMDqueue;
1097
1098         unsigned long AdapterOpenFlag:1;
1099         unsigned long AdapterVirtOpenFlag:1;
1100         unsigned long OpenCommandIssued:1;
1101         unsigned long TransmitCommandActive:1;
1102         unsigned long TransmitHaltScheduled:1;
1103         unsigned long HaltInProgress:1;
1104         unsigned long LobeWireFaultLogged:1;
1105         unsigned long ReOpenInProgress:1;
1106         unsigned long Sleeping:1;
1107
1108         unsigned long LastOpenStatus;
1109         unsigned short CurrentRingStatus;
1110         unsigned long MaxPacketSize;
1111
1112         unsigned long StartTime;
1113         unsigned long LastSendTime;
1114
1115         struct tr_statistics MacStat;   /* MAC statistics structure */
1116
1117         unsigned long dmalimit; /* the max DMA address (ie, ISA) */
1118         dma_addr_t    dmabuffer; /* the DMA bus address corresponding to
1119                                     priv. Might be different from virt_to_bus()
1120                                     for architectures with IO MMU (Alpha) */
1121
1122         struct timer_list timer;
1123
1124         wait_queue_head_t  wait_for_tok_int;
1125
1126         INTPTRS intptrs;        /* Internal adapter pointer. Must be read
1127                                  * before OPEN command.
1128                                  */
1129         unsigned short (*setnselout)(struct net_device *);
1130         unsigned short (*sifreadb)(struct net_device *, unsigned short);
1131         void (*sifwriteb)(struct net_device *, unsigned short, unsigned short);
1132         unsigned short (*sifreadw)(struct net_device *, unsigned short);
1133         void (*sifwritew)(struct net_device *, unsigned short, unsigned short);
1134
1135         spinlock_t lock;                /* SMP protection */
1136         void *tmspriv;
1137 } NET_LOCAL;
1138
1139 #endif  /* __KERNEL__ */
1140 #endif  /* __LINUX_TMS380TR_H */