Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ieee1394...
[linux-2.6] / drivers / usb / host / ohci-hcd.c
1 /*
2  * OHCI HCD (Host Controller Driver) for USB.
3  *
4  * (C) Copyright 1999 Roman Weissgaerber <weissg@vienna.at>
5  * (C) Copyright 2000-2004 David Brownell <dbrownell@users.sourceforge.net>
6  *
7  * [ Initialisation is based on Linus'  ]
8  * [ uhci code and gregs ohci fragments ]
9  * [ (C) Copyright 1999 Linus Torvalds  ]
10  * [ (C) Copyright 1999 Gregory P. Smith]
11  *
12  *
13  * OHCI is the main "non-Intel/VIA" standard for USB 1.1 host controller
14  * interfaces (though some non-x86 Intel chips use it).  It supports
15  * smarter hardware than UHCI.  A download link for the spec available
16  * through the http://www.usb.org website.
17  *
18  * This file is licenced under the GPL.
19  */
20
21 #include <linux/module.h>
22 #include <linux/moduleparam.h>
23 #include <linux/pci.h>
24 #include <linux/kernel.h>
25 #include <linux/delay.h>
26 #include <linux/ioport.h>
27 #include <linux/sched.h>
28 #include <linux/slab.h>
29 #include <linux/smp_lock.h>
30 #include <linux/errno.h>
31 #include <linux/init.h>
32 #include <linux/timer.h>
33 #include <linux/list.h>
34 #include <linux/usb.h>
35 #include <linux/usb/otg.h>
36 #include <linux/dma-mapping.h>
37 #include <linux/dmapool.h>
38 #include <linux/reboot.h>
39
40 #include <asm/io.h>
41 #include <asm/irq.h>
42 #include <asm/system.h>
43 #include <asm/unaligned.h>
44 #include <asm/byteorder.h>
45
46 #include "../core/hcd.h"
47
48 #define DRIVER_VERSION "2006 August 04"
49 #define DRIVER_AUTHOR "Roman Weissgaerber, David Brownell"
50 #define DRIVER_DESC "USB 1.1 'Open' Host Controller (OHCI) Driver"
51
52 /*-------------------------------------------------------------------------*/
53
54 #undef OHCI_VERBOSE_DEBUG       /* not always helpful */
55
56 /* For initializing controller (mask in an HCFS mode too) */
57 #define OHCI_CONTROL_INIT       OHCI_CTRL_CBSR
58 #define OHCI_INTR_INIT \
59                 (OHCI_INTR_MIE | OHCI_INTR_RHSC | OHCI_INTR_UE \
60                 | OHCI_INTR_RD | OHCI_INTR_WDH)
61
62 #ifdef __hppa__
63 /* On PA-RISC, PDC can leave IR set incorrectly; ignore it there. */
64 #define IR_DISABLE
65 #endif
66
67 #ifdef CONFIG_ARCH_OMAP
68 /* OMAP doesn't support IR (no SMM; not needed) */
69 #define IR_DISABLE
70 #endif
71
72 /*-------------------------------------------------------------------------*/
73
74 static const char       hcd_name [] = "ohci_hcd";
75
76 #define STATECHANGE_DELAY       msecs_to_jiffies(300)
77
78 #include "ohci.h"
79
80 static void ohci_dump (struct ohci_hcd *ohci, int verbose);
81 static int ohci_init (struct ohci_hcd *ohci);
82 static void ohci_stop (struct usb_hcd *hcd);
83
84 #include "ohci-hub.c"
85 #include "ohci-dbg.c"
86 #include "ohci-mem.c"
87 #include "ohci-q.c"
88
89
90 /*
91  * On architectures with edge-triggered interrupts we must never return
92  * IRQ_NONE.
93  */
94 #if defined(CONFIG_SA1111)  /* ... or other edge-triggered systems */
95 #define IRQ_NOTMINE     IRQ_HANDLED
96 #else
97 #define IRQ_NOTMINE     IRQ_NONE
98 #endif
99
100
101 /* Some boards misreport power switching/overcurrent */
102 static int distrust_firmware = 1;
103 module_param (distrust_firmware, bool, 0);
104 MODULE_PARM_DESC (distrust_firmware,
105         "true to distrust firmware power/overcurrent setup");
106
107 /* Some boards leave IR set wrongly, since they fail BIOS/SMM handshakes */
108 static int no_handshake = 0;
109 module_param (no_handshake, bool, 0);
110 MODULE_PARM_DESC (no_handshake, "true (not default) disables BIOS handshake");
111
112 /*-------------------------------------------------------------------------*/
113
114 /*
115  * queue up an urb for anything except the root hub
116  */
117 static int ohci_urb_enqueue (
118         struct usb_hcd  *hcd,
119         struct usb_host_endpoint *ep,
120         struct urb      *urb,
121         gfp_t           mem_flags
122 ) {
123         struct ohci_hcd *ohci = hcd_to_ohci (hcd);
124         struct ed       *ed;
125         urb_priv_t      *urb_priv;
126         unsigned int    pipe = urb->pipe;
127         int             i, size = 0;
128         unsigned long   flags;
129         int             retval = 0;
130
131 #ifdef OHCI_VERBOSE_DEBUG
132         urb_print (urb, "SUB", usb_pipein (pipe));
133 #endif
134
135         /* every endpoint has a ed, locate and maybe (re)initialize it */
136         if (! (ed = ed_get (ohci, ep, urb->dev, pipe, urb->interval)))
137                 return -ENOMEM;
138
139         /* for the private part of the URB we need the number of TDs (size) */
140         switch (ed->type) {
141                 case PIPE_CONTROL:
142                         /* td_submit_urb() doesn't yet handle these */
143                         if (urb->transfer_buffer_length > 4096)
144                                 return -EMSGSIZE;
145
146                         /* 1 TD for setup, 1 for ACK, plus ... */
147                         size = 2;
148                         /* FALLTHROUGH */
149                 // case PIPE_INTERRUPT:
150                 // case PIPE_BULK:
151                 default:
152                         /* one TD for every 4096 Bytes (can be upto 8K) */
153                         size += urb->transfer_buffer_length / 4096;
154                         /* ... and for any remaining bytes ... */
155                         if ((urb->transfer_buffer_length % 4096) != 0)
156                                 size++;
157                         /* ... and maybe a zero length packet to wrap it up */
158                         if (size == 0)
159                                 size++;
160                         else if ((urb->transfer_flags & URB_ZERO_PACKET) != 0
161                                 && (urb->transfer_buffer_length
162                                         % usb_maxpacket (urb->dev, pipe,
163                                                 usb_pipeout (pipe))) == 0)
164                                 size++;
165                         break;
166                 case PIPE_ISOCHRONOUS: /* number of packets from URB */
167                         size = urb->number_of_packets;
168                         break;
169         }
170
171         /* allocate the private part of the URB */
172         urb_priv = kmalloc (sizeof (urb_priv_t) + size * sizeof (struct td *),
173                         mem_flags);
174         if (!urb_priv)
175                 return -ENOMEM;
176         memset (urb_priv, 0, sizeof (urb_priv_t) + size * sizeof (struct td *));
177         INIT_LIST_HEAD (&urb_priv->pending);
178         urb_priv->length = size;
179         urb_priv->ed = ed;
180
181         /* allocate the TDs (deferring hash chain updates) */
182         for (i = 0; i < size; i++) {
183                 urb_priv->td [i] = td_alloc (ohci, mem_flags);
184                 if (!urb_priv->td [i]) {
185                         urb_priv->length = i;
186                         urb_free_priv (ohci, urb_priv);
187                         return -ENOMEM;
188                 }
189         }
190
191         spin_lock_irqsave (&ohci->lock, flags);
192
193         /* don't submit to a dead HC */
194         if (!test_bit(HCD_FLAG_HW_ACCESSIBLE, &hcd->flags)) {
195                 retval = -ENODEV;
196                 goto fail;
197         }
198         if (!HC_IS_RUNNING(hcd->state)) {
199                 retval = -ENODEV;
200                 goto fail;
201         }
202
203         /* in case of unlink-during-submit */
204         spin_lock (&urb->lock);
205         if (urb->status != -EINPROGRESS) {
206                 spin_unlock (&urb->lock);
207                 urb->hcpriv = urb_priv;
208                 finish_urb (ohci, urb);
209                 retval = 0;
210                 goto fail;
211         }
212
213         /* schedule the ed if needed */
214         if (ed->state == ED_IDLE) {
215                 retval = ed_schedule (ohci, ed);
216                 if (retval < 0)
217                         goto fail0;
218                 if (ed->type == PIPE_ISOCHRONOUS) {
219                         u16     frame = ohci_frame_no(ohci);
220
221                         /* delay a few frames before the first TD */
222                         frame += max_t (u16, 8, ed->interval);
223                         frame &= ~(ed->interval - 1);
224                         frame |= ed->branch;
225                         urb->start_frame = frame;
226
227                         /* yes, only URB_ISO_ASAP is supported, and
228                          * urb->start_frame is never used as input.
229                          */
230                 }
231         } else if (ed->type == PIPE_ISOCHRONOUS)
232                 urb->start_frame = ed->last_iso + ed->interval;
233
234         /* fill the TDs and link them to the ed; and
235          * enable that part of the schedule, if needed
236          * and update count of queued periodic urbs
237          */
238         urb->hcpriv = urb_priv;
239         td_submit_urb (ohci, urb);
240
241 fail0:
242         spin_unlock (&urb->lock);
243 fail:
244         if (retval)
245                 urb_free_priv (ohci, urb_priv);
246         spin_unlock_irqrestore (&ohci->lock, flags);
247         return retval;
248 }
249
250 /*
251  * decouple the URB from the HC queues (TDs, urb_priv); it's
252  * already marked using urb->status.  reporting is always done
253  * asynchronously, and we might be dealing with an urb that's
254  * partially transferred, or an ED with other urbs being unlinked.
255  */
256 static int ohci_urb_dequeue (struct usb_hcd *hcd, struct urb *urb)
257 {
258         struct ohci_hcd         *ohci = hcd_to_ohci (hcd);
259         unsigned long           flags;
260
261 #ifdef OHCI_VERBOSE_DEBUG
262         urb_print (urb, "UNLINK", 1);
263 #endif
264
265         spin_lock_irqsave (&ohci->lock, flags);
266         if (HC_IS_RUNNING(hcd->state)) {
267                 urb_priv_t  *urb_priv;
268
269                 /* Unless an IRQ completed the unlink while it was being
270                  * handed to us, flag it for unlink and giveback, and force
271                  * some upcoming INTR_SF to call finish_unlinks()
272                  */
273                 urb_priv = urb->hcpriv;
274                 if (urb_priv) {
275                         if (urb_priv->ed->state == ED_OPER)
276                                 start_ed_unlink (ohci, urb_priv->ed);
277                 }
278         } else {
279                 /*
280                  * with HC dead, we won't respect hc queue pointers
281                  * any more ... just clean up every urb's memory.
282                  */
283                 if (urb->hcpriv)
284                         finish_urb (ohci, urb);
285         }
286         spin_unlock_irqrestore (&ohci->lock, flags);
287         return 0;
288 }
289
290 /*-------------------------------------------------------------------------*/
291
292 /* frees config/altsetting state for endpoints,
293  * including ED memory, dummy TD, and bulk/intr data toggle
294  */
295
296 static void
297 ohci_endpoint_disable (struct usb_hcd *hcd, struct usb_host_endpoint *ep)
298 {
299         struct ohci_hcd         *ohci = hcd_to_ohci (hcd);
300         unsigned long           flags;
301         struct ed               *ed = ep->hcpriv;
302         unsigned                limit = 1000;
303
304         /* ASSERT:  any requests/urbs are being unlinked */
305         /* ASSERT:  nobody can be submitting urbs for this any more */
306
307         if (!ed)
308                 return;
309
310 rescan:
311         spin_lock_irqsave (&ohci->lock, flags);
312
313         if (!HC_IS_RUNNING (hcd->state)) {
314 sanitize:
315                 ed->state = ED_IDLE;
316                 finish_unlinks (ohci, 0);
317         }
318
319         switch (ed->state) {
320         case ED_UNLINK:         /* wait for hw to finish? */
321                 /* major IRQ delivery trouble loses INTR_SF too... */
322                 if (limit-- == 0) {
323                         ohci_warn (ohci, "IRQ INTR_SF lossage\n");
324                         goto sanitize;
325                 }
326                 spin_unlock_irqrestore (&ohci->lock, flags);
327                 schedule_timeout_uninterruptible(1);
328                 goto rescan;
329         case ED_IDLE:           /* fully unlinked */
330                 if (list_empty (&ed->td_list)) {
331                         td_free (ohci, ed->dummy);
332                         ed_free (ohci, ed);
333                         break;
334                 }
335                 /* else FALL THROUGH */
336         default:
337                 /* caller was supposed to have unlinked any requests;
338                  * that's not our job.  can't recover; must leak ed.
339                  */
340                 ohci_err (ohci, "leak ed %p (#%02x) state %d%s\n",
341                         ed, ep->desc.bEndpointAddress, ed->state,
342                         list_empty (&ed->td_list) ? "" : " (has tds)");
343                 td_free (ohci, ed->dummy);
344                 break;
345         }
346         ep->hcpriv = NULL;
347         spin_unlock_irqrestore (&ohci->lock, flags);
348         return;
349 }
350
351 static int ohci_get_frame (struct usb_hcd *hcd)
352 {
353         struct ohci_hcd         *ohci = hcd_to_ohci (hcd);
354
355         return ohci_frame_no(ohci);
356 }
357
358 static void ohci_usb_reset (struct ohci_hcd *ohci)
359 {
360         ohci->hc_control = ohci_readl (ohci, &ohci->regs->control);
361         ohci->hc_control &= OHCI_CTRL_RWC;
362         ohci_writel (ohci, ohci->hc_control, &ohci->regs->control);
363 }
364
365 /* ohci_shutdown forcibly disables IRQs and DMA, helping kexec and
366  * other cases where the next software may expect clean state from the
367  * "firmware".  this is bus-neutral, unlike shutdown() methods.
368  */
369 static void
370 ohci_shutdown (struct usb_hcd *hcd)
371 {
372         struct ohci_hcd *ohci;
373
374         ohci = hcd_to_ohci (hcd);
375         ohci_writel (ohci, OHCI_INTR_MIE, &ohci->regs->intrdisable);
376         ohci_usb_reset (ohci);
377         /* flush the writes */
378         (void) ohci_readl (ohci, &ohci->regs->control);
379 }
380
381 /*-------------------------------------------------------------------------*
382  * HC functions
383  *-------------------------------------------------------------------------*/
384
385 /* init memory, and kick BIOS/SMM off */
386
387 static int ohci_init (struct ohci_hcd *ohci)
388 {
389         int ret;
390         struct usb_hcd *hcd = ohci_to_hcd(ohci);
391
392         disable (ohci);
393         ohci->regs = hcd->regs;
394
395         /* REVISIT this BIOS handshake is now moved into PCI "quirks", and
396          * was never needed for most non-PCI systems ... remove the code?
397          */
398
399 #ifndef IR_DISABLE
400         /* SMM owns the HC?  not for long! */
401         if (!no_handshake && ohci_readl (ohci,
402                                         &ohci->regs->control) & OHCI_CTRL_IR) {
403                 u32 temp;
404
405                 ohci_dbg (ohci, "USB HC TakeOver from BIOS/SMM\n");
406
407                 /* this timeout is arbitrary.  we make it long, so systems
408                  * depending on usb keyboards may be usable even if the
409                  * BIOS/SMM code seems pretty broken.
410                  */
411                 temp = 500;     /* arbitrary: five seconds */
412
413                 ohci_writel (ohci, OHCI_INTR_OC, &ohci->regs->intrenable);
414                 ohci_writel (ohci, OHCI_OCR, &ohci->regs->cmdstatus);
415                 while (ohci_readl (ohci, &ohci->regs->control) & OHCI_CTRL_IR) {
416                         msleep (10);
417                         if (--temp == 0) {
418                                 ohci_err (ohci, "USB HC takeover failed!"
419                                         "  (BIOS/SMM bug)\n");
420                                 return -EBUSY;
421                         }
422                 }
423                 ohci_usb_reset (ohci);
424         }
425 #endif
426
427         /* Disable HC interrupts */
428         ohci_writel (ohci, OHCI_INTR_MIE, &ohci->regs->intrdisable);
429
430         /* flush the writes, and save key bits like RWC */
431         if (ohci_readl (ohci, &ohci->regs->control) & OHCI_CTRL_RWC)
432                 ohci->hc_control |= OHCI_CTRL_RWC;
433
434         /* Read the number of ports unless overridden */
435         if (ohci->num_ports == 0)
436                 ohci->num_ports = roothub_a(ohci) & RH_A_NDP;
437
438         if (ohci->hcca)
439                 return 0;
440
441         ohci->hcca = dma_alloc_coherent (hcd->self.controller,
442                         sizeof *ohci->hcca, &ohci->hcca_dma, 0);
443         if (!ohci->hcca)
444                 return -ENOMEM;
445
446         if ((ret = ohci_mem_init (ohci)) < 0)
447                 ohci_stop (hcd);
448         else {
449                 create_debug_files (ohci);
450         }
451
452         return ret;
453 }
454
455 /*-------------------------------------------------------------------------*/
456
457 /* Start an OHCI controller, set the BUS operational
458  * resets USB and controller
459  * enable interrupts
460  */
461 static int ohci_run (struct ohci_hcd *ohci)
462 {
463         u32                     mask, temp;
464         int                     first = ohci->fminterval == 0;
465         struct usb_hcd          *hcd = ohci_to_hcd(ohci);
466
467         disable (ohci);
468
469         /* boot firmware should have set this up (5.1.1.3.1) */
470         if (first) {
471
472                 temp = ohci_readl (ohci, &ohci->regs->fminterval);
473                 ohci->fminterval = temp & 0x3fff;
474                 if (ohci->fminterval != FI)
475                         ohci_dbg (ohci, "fminterval delta %d\n",
476                                 ohci->fminterval - FI);
477                 ohci->fminterval |= FSMP (ohci->fminterval) << 16;
478                 /* also: power/overcurrent flags in roothub.a */
479         }
480
481         /* Reset USB nearly "by the book".  RemoteWakeupConnected was
482          * saved if boot firmware (BIOS/SMM/...) told us it's connected,
483          * or if bus glue did the same (e.g. for PCI add-in cards with
484          * PCI PM support).
485          */
486         ohci_dbg (ohci, "resetting from state '%s', control = 0x%x\n",
487                         hcfs2string (ohci->hc_control & OHCI_CTRL_HCFS),
488                         ohci_readl (ohci, &ohci->regs->control));
489         if ((ohci->hc_control & OHCI_CTRL_RWC) != 0
490                         && !device_may_wakeup(hcd->self.controller))
491                 device_init_wakeup(hcd->self.controller, 1);
492
493         switch (ohci->hc_control & OHCI_CTRL_HCFS) {
494         case OHCI_USB_OPER:
495                 temp = 0;
496                 break;
497         case OHCI_USB_SUSPEND:
498         case OHCI_USB_RESUME:
499                 ohci->hc_control &= OHCI_CTRL_RWC;
500                 ohci->hc_control |= OHCI_USB_RESUME;
501                 temp = 10 /* msec wait */;
502                 break;
503         // case OHCI_USB_RESET:
504         default:
505                 ohci->hc_control &= OHCI_CTRL_RWC;
506                 ohci->hc_control |= OHCI_USB_RESET;
507                 temp = 50 /* msec wait */;
508                 break;
509         }
510         ohci_writel (ohci, ohci->hc_control, &ohci->regs->control);
511         // flush the writes
512         (void) ohci_readl (ohci, &ohci->regs->control);
513         msleep(temp);
514         temp = roothub_a (ohci);
515         if (!(temp & RH_A_NPS)) {
516                 /* power down each port */
517                 for (temp = 0; temp < ohci->num_ports; temp++)
518                         ohci_writel (ohci, RH_PS_LSDA,
519                                 &ohci->regs->roothub.portstatus [temp]);
520         }
521         // flush those writes
522         (void) ohci_readl (ohci, &ohci->regs->control);
523         memset (ohci->hcca, 0, sizeof (struct ohci_hcca));
524
525         /* 2msec timelimit here means no irqs/preempt */
526         spin_lock_irq (&ohci->lock);
527
528 retry:
529         /* HC Reset requires max 10 us delay */
530         ohci_writel (ohci, OHCI_HCR,  &ohci->regs->cmdstatus);
531         temp = 30;      /* ... allow extra time */
532         while ((ohci_readl (ohci, &ohci->regs->cmdstatus) & OHCI_HCR) != 0) {
533                 if (--temp == 0) {
534                         spin_unlock_irq (&ohci->lock);
535                         ohci_err (ohci, "USB HC reset timed out!\n");
536                         return -1;
537                 }
538                 udelay (1);
539         }
540
541         /* now we're in the SUSPEND state ... must go OPERATIONAL
542          * within 2msec else HC enters RESUME
543          *
544          * ... but some hardware won't init fmInterval "by the book"
545          * (SiS, OPTi ...), so reset again instead.  SiS doesn't need
546          * this if we write fmInterval after we're OPERATIONAL.
547          * Unclear about ALi, ServerWorks, and others ... this could
548          * easily be a longstanding bug in chip init on Linux.
549          */
550         if (ohci->flags & OHCI_QUIRK_INITRESET) {
551                 ohci_writel (ohci, ohci->hc_control, &ohci->regs->control);
552                 // flush those writes
553                 (void) ohci_readl (ohci, &ohci->regs->control);
554         }
555
556         /* Tell the controller where the control and bulk lists are
557          * The lists are empty now. */
558         ohci_writel (ohci, 0, &ohci->regs->ed_controlhead);
559         ohci_writel (ohci, 0, &ohci->regs->ed_bulkhead);
560
561         /* a reset clears this */
562         ohci_writel (ohci, (u32) ohci->hcca_dma, &ohci->regs->hcca);
563
564         periodic_reinit (ohci);
565
566         /* some OHCI implementations are finicky about how they init.
567          * bogus values here mean not even enumeration could work.
568          */
569         if ((ohci_readl (ohci, &ohci->regs->fminterval) & 0x3fff0000) == 0
570                         || !ohci_readl (ohci, &ohci->regs->periodicstart)) {
571                 if (!(ohci->flags & OHCI_QUIRK_INITRESET)) {
572                         ohci->flags |= OHCI_QUIRK_INITRESET;
573                         ohci_dbg (ohci, "enabling initreset quirk\n");
574                         goto retry;
575                 }
576                 spin_unlock_irq (&ohci->lock);
577                 ohci_err (ohci, "init err (%08x %04x)\n",
578                         ohci_readl (ohci, &ohci->regs->fminterval),
579                         ohci_readl (ohci, &ohci->regs->periodicstart));
580                 return -EOVERFLOW;
581         }
582
583         /* use rhsc irqs after khubd is fully initialized */
584         hcd->poll_rh = 1;
585         hcd->uses_new_polling = 1;
586
587         /* start controller operations */
588         ohci->hc_control &= OHCI_CTRL_RWC;
589         ohci->hc_control |= OHCI_CONTROL_INIT | OHCI_USB_OPER;
590         ohci_writel (ohci, ohci->hc_control, &ohci->regs->control);
591         hcd->state = HC_STATE_RUNNING;
592
593         /* wake on ConnectStatusChange, matching external hubs */
594         ohci_writel (ohci, RH_HS_DRWE, &ohci->regs->roothub.status);
595
596         /* Choose the interrupts we care about now, others later on demand */
597         mask = OHCI_INTR_INIT;
598         ohci_writel (ohci, ~0, &ohci->regs->intrstatus);
599         ohci_writel (ohci, mask, &ohci->regs->intrenable);
600
601         /* handle root hub init quirks ... */
602         temp = roothub_a (ohci);
603         temp &= ~(RH_A_PSM | RH_A_OCPM);
604         if (ohci->flags & OHCI_QUIRK_SUPERIO) {
605                 /* NSC 87560 and maybe others */
606                 temp |= RH_A_NOCP;
607                 temp &= ~(RH_A_POTPGT | RH_A_NPS);
608                 ohci_writel (ohci, temp, &ohci->regs->roothub.a);
609         } else if ((ohci->flags & OHCI_QUIRK_AMD756) || distrust_firmware) {
610                 /* hub power always on; required for AMD-756 and some
611                  * Mac platforms.  ganged overcurrent reporting, if any.
612                  */
613                 temp |= RH_A_NPS;
614                 ohci_writel (ohci, temp, &ohci->regs->roothub.a);
615         }
616         ohci_writel (ohci, RH_HS_LPSC, &ohci->regs->roothub.status);
617         ohci_writel (ohci, (temp & RH_A_NPS) ? 0 : RH_B_PPCM,
618                                                 &ohci->regs->roothub.b);
619         // flush those writes
620         (void) ohci_readl (ohci, &ohci->regs->control);
621
622         ohci->next_statechange = jiffies + STATECHANGE_DELAY;
623         spin_unlock_irq (&ohci->lock);
624
625         // POTPGT delay is bits 24-31, in 2 ms units.
626         mdelay ((temp >> 23) & 0x1fe);
627         hcd->state = HC_STATE_RUNNING;
628
629         ohci_dump (ohci, 1);
630
631         return 0;
632 }
633
634 /*-------------------------------------------------------------------------*/
635
636 /* an interrupt happens */
637
638 static irqreturn_t ohci_irq (struct usb_hcd *hcd)
639 {
640         struct ohci_hcd         *ohci = hcd_to_ohci (hcd);
641         struct ohci_regs __iomem *regs = ohci->regs;
642         int                     ints; 
643
644         /* we can eliminate a (slow) ohci_readl()
645            if _only_ WDH caused this irq */
646         if ((ohci->hcca->done_head != 0)
647                         && ! (hc32_to_cpup (ohci, &ohci->hcca->done_head)
648                                 & 0x01)) {
649                 ints =  OHCI_INTR_WDH;
650
651         /* cardbus/... hardware gone before remove() */
652         } else if ((ints = ohci_readl (ohci, &regs->intrstatus)) == ~(u32)0) {
653                 disable (ohci);
654                 ohci_dbg (ohci, "device removed!\n");
655                 return IRQ_HANDLED;
656
657         /* interrupt for some other device? */
658         } else if ((ints &= ohci_readl (ohci, &regs->intrenable)) == 0) {
659                 return IRQ_NOTMINE;
660         }
661
662         if (ints & OHCI_INTR_UE) {
663                 disable (ohci);
664                 ohci_err (ohci, "OHCI Unrecoverable Error, disabled\n");
665                 // e.g. due to PCI Master/Target Abort
666
667                 ohci_dump (ohci, 1);
668                 ohci_usb_reset (ohci);
669         }
670
671         if (ints & OHCI_INTR_RHSC) {
672                 ohci_vdbg(ohci, "rhsc\n");
673                 ohci->next_statechange = jiffies + STATECHANGE_DELAY;
674                 ohci_writel(ohci, OHCI_INTR_RD | OHCI_INTR_RHSC,
675                                 &regs->intrstatus);
676
677                 /* NOTE: Vendors didn't always make the same implementation
678                  * choices for RHSC.  Many followed the spec; RHSC triggers
679                  * on an edge, like setting and maybe clearing a port status
680                  * change bit.  With others it's level-triggered, active
681                  * until khubd clears all the port status change bits.  We'll
682                  * always disable it here and rely on polling until khubd
683                  * re-enables it.
684                  */
685                 ohci_writel(ohci, OHCI_INTR_RHSC, &regs->intrdisable);
686                 usb_hcd_poll_rh_status(hcd);
687         }
688
689         /* For connect and disconnect events, we expect the controller
690          * to turn on RHSC along with RD.  But for remote wakeup events
691          * this might not happen.
692          */
693         else if (ints & OHCI_INTR_RD) {
694                 ohci_vdbg(ohci, "resume detect\n");
695                 ohci_writel(ohci, OHCI_INTR_RD, &regs->intrstatus);
696                 hcd->poll_rh = 1;
697                 if (ohci->autostop) {
698                         spin_lock (&ohci->lock);
699                         ohci_rh_resume (ohci);
700                         spin_unlock (&ohci->lock);
701                 } else
702                         usb_hcd_resume_root_hub(hcd);
703         }
704
705         if (ints & OHCI_INTR_WDH) {
706                 if (HC_IS_RUNNING(hcd->state))
707                         ohci_writel (ohci, OHCI_INTR_WDH, &regs->intrdisable);
708                 spin_lock (&ohci->lock);
709                 dl_done_list (ohci);
710                 spin_unlock (&ohci->lock);
711                 if (HC_IS_RUNNING(hcd->state))
712                         ohci_writel (ohci, OHCI_INTR_WDH, &regs->intrenable);
713         }
714
715         /* could track INTR_SO to reduce available PCI/... bandwidth */
716
717         /* handle any pending URB/ED unlinks, leaving INTR_SF enabled
718          * when there's still unlinking to be done (next frame).
719          */
720         spin_lock (&ohci->lock);
721         if (ohci->ed_rm_list)
722                 finish_unlinks (ohci, ohci_frame_no(ohci));
723         if ((ints & OHCI_INTR_SF) != 0 && !ohci->ed_rm_list
724                         && HC_IS_RUNNING(hcd->state))
725                 ohci_writel (ohci, OHCI_INTR_SF, &regs->intrdisable);
726         spin_unlock (&ohci->lock);
727
728         if (HC_IS_RUNNING(hcd->state)) {
729                 ohci_writel (ohci, ints, &regs->intrstatus);
730                 ohci_writel (ohci, OHCI_INTR_MIE, &regs->intrenable);
731                 // flush those writes
732                 (void) ohci_readl (ohci, &ohci->regs->control);
733         }
734
735         return IRQ_HANDLED;
736 }
737
738 /*-------------------------------------------------------------------------*/
739
740 static void ohci_stop (struct usb_hcd *hcd)
741 {
742         struct ohci_hcd         *ohci = hcd_to_ohci (hcd);
743
744         ohci_dbg (ohci, "stop %s controller (state 0x%02x)\n",
745                 hcfs2string (ohci->hc_control & OHCI_CTRL_HCFS),
746                 hcd->state);
747         ohci_dump (ohci, 1);
748
749         flush_scheduled_work();
750
751         ohci_usb_reset (ohci);
752         ohci_writel (ohci, OHCI_INTR_MIE, &ohci->regs->intrdisable);
753         free_irq(hcd->irq, hcd);
754         hcd->irq = -1;
755
756         remove_debug_files (ohci);
757         ohci_mem_cleanup (ohci);
758         if (ohci->hcca) {
759                 dma_free_coherent (hcd->self.controller,
760                                 sizeof *ohci->hcca,
761                                 ohci->hcca, ohci->hcca_dma);
762                 ohci->hcca = NULL;
763                 ohci->hcca_dma = 0;
764         }
765 }
766
767 /*-------------------------------------------------------------------------*/
768
769 /* must not be called from interrupt context */
770
771 #ifdef  CONFIG_PM
772
773 static int ohci_restart (struct ohci_hcd *ohci)
774 {
775         int temp;
776         int i;
777         struct urb_priv *priv;
778
779         /* mark any devices gone, so they do nothing till khubd disconnects.
780          * recycle any "live" eds/tds (and urbs) right away.
781          * later, khubd disconnect processing will recycle the other state,
782          * (either as disconnect/reconnect, or maybe someday as a reset).
783          */
784         spin_lock_irq(&ohci->lock);
785         disable (ohci);
786         usb_root_hub_lost_power(ohci_to_hcd(ohci)->self.root_hub);
787         if (!list_empty (&ohci->pending))
788                 ohci_dbg(ohci, "abort schedule...\n");
789         list_for_each_entry (priv, &ohci->pending, pending) {
790                 struct urb      *urb = priv->td[0]->urb;
791                 struct ed       *ed = priv->ed;
792
793                 switch (ed->state) {
794                 case ED_OPER:
795                         ed->state = ED_UNLINK;
796                         ed->hwINFO |= cpu_to_hc32(ohci, ED_DEQUEUE);
797                         ed_deschedule (ohci, ed);
798
799                         ed->ed_next = ohci->ed_rm_list;
800                         ed->ed_prev = NULL;
801                         ohci->ed_rm_list = ed;
802                         /* FALLTHROUGH */
803                 case ED_UNLINK:
804                         break;
805                 default:
806                         ohci_dbg(ohci, "bogus ed %p state %d\n",
807                                         ed, ed->state);
808                 }
809
810                 spin_lock (&urb->lock);
811                 urb->status = -ESHUTDOWN;
812                 spin_unlock (&urb->lock);
813         }
814         finish_unlinks (ohci, 0);
815         spin_unlock_irq(&ohci->lock);
816
817         /* paranoia, in case that didn't work: */
818
819         /* empty the interrupt branches */
820         for (i = 0; i < NUM_INTS; i++) ohci->load [i] = 0;
821         for (i = 0; i < NUM_INTS; i++) ohci->hcca->int_table [i] = 0;
822
823         /* no EDs to remove */
824         ohci->ed_rm_list = NULL;
825
826         /* empty control and bulk lists */
827         ohci->ed_controltail = NULL;
828         ohci->ed_bulktail    = NULL;
829
830         if ((temp = ohci_run (ohci)) < 0) {
831                 ohci_err (ohci, "can't restart, %d\n", temp);
832                 return temp;
833         } else {
834                 /* here we "know" root ports should always stay powered,
835                  * and that if we try to turn them back on the root hub
836                  * will respond to CSC processing.
837                  */
838                 i = ohci->num_ports;
839                 while (i--)
840                         ohci_writel (ohci, RH_PS_PSS,
841                                 &ohci->regs->roothub.portstatus [i]);
842                 ohci_dbg (ohci, "restart complete\n");
843         }
844         return 0;
845 }
846 #endif
847
848 /*-------------------------------------------------------------------------*/
849
850 #define DRIVER_INFO DRIVER_VERSION " " DRIVER_DESC
851
852 MODULE_AUTHOR (DRIVER_AUTHOR);
853 MODULE_DESCRIPTION (DRIVER_INFO);
854 MODULE_LICENSE ("GPL");
855
856 #ifdef CONFIG_PCI
857 #include "ohci-pci.c"
858 #endif
859
860 #ifdef CONFIG_SA1111
861 #include "ohci-sa1111.c"
862 #endif
863
864 #ifdef CONFIG_ARCH_S3C2410
865 #include "ohci-s3c2410.c"
866 #endif
867
868 #ifdef CONFIG_ARCH_OMAP
869 #include "ohci-omap.c"
870 #endif
871
872 #ifdef CONFIG_ARCH_LH7A404
873 #include "ohci-lh7a404.c"
874 #endif
875
876 #ifdef CONFIG_PXA27x
877 #include "ohci-pxa27x.c"
878 #endif
879
880 #ifdef CONFIG_ARCH_EP93XX
881 #include "ohci-ep93xx.c"
882 #endif
883
884 #ifdef CONFIG_SOC_AU1X00
885 #include "ohci-au1xxx.c"
886 #endif
887
888 #ifdef CONFIG_PNX8550
889 #include "ohci-pnx8550.c"
890 #endif
891
892 #ifdef CONFIG_USB_OHCI_HCD_PPC_SOC
893 #include "ohci-ppc-soc.c"
894 #endif
895
896 #ifdef CONFIG_ARCH_AT91
897 #include "ohci-at91.c"
898 #endif
899
900 #ifdef CONFIG_ARCH_PNX4008
901 #include "ohci-pnx4008.c"
902 #endif
903
904 #if !(defined(CONFIG_PCI) \
905       || defined(CONFIG_SA1111) \
906       || defined(CONFIG_ARCH_S3C2410) \
907       || defined(CONFIG_ARCH_OMAP) \
908       || defined (CONFIG_ARCH_LH7A404) \
909       || defined (CONFIG_PXA27x) \
910       || defined (CONFIG_ARCH_EP93XX) \
911       || defined (CONFIG_SOC_AU1X00) \
912       || defined (CONFIG_USB_OHCI_HCD_PPC_SOC) \
913       || defined (CONFIG_ARCH_AT91) \
914       || defined (CONFIG_ARCH_PNX4008) \
915         )
916 #error "missing bus glue for ohci-hcd"
917 #endif