git.oblomov.eu Git - linux-2.6/blob - drivers/mmc/au1xmmc.c

   1 /*
   2  * linux/drivers/mmc/au1xmmc.c - AU1XX0 MMC driver
   3  *
   4  *  Copyright (c) 2005, Advanced Micro Devices, Inc.
   5  *
   6  *  Developed with help from the 2.4.30 MMC AU1XXX controller including
   7  *  the following copyright notices:
   8  *     Copyright (c) 2003-2004 Embedded Edge, LLC.
   9  *     Portions Copyright (C) 2002 Embedix, Inc
  10  *     Copyright 2002 Hewlett-Packard Company
  11
  12  *  2.6 version of this driver inspired by:
  13  *     (drivers/mmc/wbsd.c) Copyright (C) 2004-2005 Pierre Ossman,
  14  *     All Rights Reserved.
  15  *     (drivers/mmc/pxa.c) Copyright (C) 2003 Russell King,
  16  *     All Rights Reserved.
  17  *
  18
  19  * This program is free software; you can redistribute it and/or modify
  20  * it under the terms of the GNU General Public License version 2 as
  21  * published by the Free Software Foundation.
  22  */
  23
  24 /* Why is a timer used to detect insert events?
  25  *
  26  * From the AU1100 MMC application guide:
  27  * If the Au1100-based design is intended to support both MultiMediaCards
  28  * and 1- or 4-data bit SecureDigital cards, then the solution is to
  29  * connect a weak (560KOhm) pull-up resistor to connector pin 1.
  30  * In doing so, a MMC card never enters SPI-mode communications,
  31  * but now the SecureDigital card-detect feature of CD/DAT3 is ineffective
  32  * (the low to high transition will not occur).
  33  *
  34  * So we use the timer to check the status manually.
  35  */
  36
  37 #include <linux/config.h>
  38 #include <linux/module.h>
  39 #include <linux/init.h>
  40 #include <linux/platform_device.h>
  41 #include <linux/mm.h>
  42 #include <linux/interrupt.h>
  43 #include <linux/dma-mapping.h>
  44
  45 #include <linux/mmc/host.h>
  46 #include <linux/mmc/protocol.h>
  47 #include <asm/io.h>
  48 #include <asm/mach-au1x00/au1000.h>
  49 #include <asm/mach-au1x00/au1xxx_dbdma.h>
  50 #include <asm/mach-au1x00/au1100_mmc.h>
  51 #include <asm/scatterlist.h>
  52
  53 #include <au1xxx.h>
  54 #include "au1xmmc.h"
  55
  56 #define DRIVER_NAME "au1xxx-mmc"
  57
  58 /* Set this to enable special debugging macros */
  59 /* #define MMC_DEBUG */
  60
  61 #ifdef MMC_DEBUG
  62 #define DEBUG(fmt, idx, args...) printk("au1xx(%d): DEBUG: " fmt, idx, ##args)
  63 #else
  64 #define DEBUG(fmt, idx, args...)
  65 #endif
  66
  67 const struct {
  68         u32 iobase;
  69         u32 tx_devid, rx_devid;
  70         u16 bcsrpwr;
  71         u16 bcsrstatus;
  72         u16 wpstatus;
  73 } au1xmmc_card_table[] = {
  74         { SD0_BASE, DSCR_CMD0_SDMS_TX0, DSCR_CMD0_SDMS_RX0,
  75           BCSR_BOARD_SD0PWR, BCSR_INT_SD0INSERT, BCSR_STATUS_SD0WP },
  76 #ifndef CONFIG_MIPS_DB1200
  77         { SD1_BASE, DSCR_CMD0_SDMS_TX1, DSCR_CMD0_SDMS_RX1,
  78           BCSR_BOARD_DS1PWR, BCSR_INT_SD1INSERT, BCSR_STATUS_SD1WP }
  79 #endif
  80 };
  81
  82 #define AU1XMMC_CONTROLLER_COUNT \
  83         (sizeof(au1xmmc_card_table) / sizeof(au1xmmc_card_table[0]))
  84
  85 /* This array stores pointers for the hosts (used by the IRQ handler) */
  86 struct au1xmmc_host *au1xmmc_hosts[AU1XMMC_CONTROLLER_COUNT];
  87 static int dma = 1;
  88
  89 #ifdef MODULE
  90 module_param(dma, bool, 0);
  91 MODULE_PARM_DESC(dma, "Use DMA engine for data transfers (0 = disabled)");
  92 #endif
  93
  94 static inline void IRQ_ON(struct au1xmmc_host *host, u32 mask)
  95 {
  96         u32 val = au_readl(HOST_CONFIG(host));
  97         val |= mask;
  98         au_writel(val, HOST_CONFIG(host));
  99         au_sync();
 100 }
 101
 102 static inline void FLUSH_FIFO(struct au1xmmc_host *host)
 103 {
 104         u32 val = au_readl(HOST_CONFIG2(host));
 105
 106         au_writel(val | SD_CONFIG2_FF, HOST_CONFIG2(host));
 107         au_sync_delay(1);
 108
 109         /* SEND_STOP will turn off clock control - this re-enables it */
 110         val &= ~SD_CONFIG2_DF;
 111
 112         au_writel(val, HOST_CONFIG2(host));
 113         au_sync();
 114 }
 115
 116 static inline void IRQ_OFF(struct au1xmmc_host *host, u32 mask)
 117 {
 118         u32 val = au_readl(HOST_CONFIG(host));
 119         val &= ~mask;
 120         au_writel(val, HOST_CONFIG(host));
 121         au_sync();
 122 }
 123
 124 static inline void SEND_STOP(struct au1xmmc_host *host)
 125 {
 126
 127         /* We know the value of CONFIG2, so avoid a read we don't need */
 128         u32 mask = SD_CONFIG2_EN;
 129
 130         WARN_ON(host->status != HOST_S_DATA);
 131         host->status = HOST_S_STOP;
 132
 133         au_writel(mask | SD_CONFIG2_DF, HOST_CONFIG2(host));
 134         au_sync();
 135
 136         /* Send the stop commmand */
 137         au_writel(STOP_CMD, HOST_CMD(host));
 138 }
 139
 140 static void au1xmmc_set_power(struct au1xmmc_host *host, int state)
 141 {
 142
 143         u32 val = au1xmmc_card_table[host->id].bcsrpwr;
 144
 145         bcsr->board &= ~val;
 146         if (state) bcsr->board |= val;
 147
 148         au_sync_delay(1);
 149 }
 150
 151 static inline int au1xmmc_card_inserted(struct au1xmmc_host *host)
 152 {
 153         return (bcsr->sig_status & au1xmmc_card_table[host->id].bcsrstatus)
 154                 ? 1 : 0;
 155 }
 156
 157 static inline int au1xmmc_card_readonly(struct au1xmmc_host *host)
 158 {
 159         return (bcsr->status & au1xmmc_card_table[host->id].wpstatus)
 160                 ? 1 : 0;
 161 }
 162
 163 static void au1xmmc_finish_request(struct au1xmmc_host *host)
 164 {
 165
 166         struct mmc_request *mrq = host->mrq;
 167
 168         host->mrq = NULL;
 169         host->flags &= HOST_F_ACTIVE;
 170
 171         host->dma.len = 0;
 172         host->dma.dir = 0;
 173
 174         host->pio.index  = 0;
 175         host->pio.offset = 0;
 176         host->pio.len = 0;
 177
 178         host->status = HOST_S_IDLE;
 179
 180         bcsr->disk_leds |= (1 << 8);
 181
 182         mmc_request_done(host->mmc, mrq);
 183 }
 184
 185 static void au1xmmc_tasklet_finish(unsigned long param)
 186 {
 187         struct au1xmmc_host *host = (struct au1xmmc_host *) param;
 188         au1xmmc_finish_request(host);
 189 }
 190
 191 static int au1xmmc_send_command(struct au1xmmc_host *host, int wait,
 192                                 struct mmc_command *cmd)
 193 {
 194
 195         u32 mmccmd = (cmd->opcode << SD_CMD_CI_SHIFT);
 196
 197         switch (mmc_resp_type(cmd)) {
 198         case MMC_RSP_R1:
 199                 mmccmd |= SD_CMD_RT_1;
 200                 break;
 201         case MMC_RSP_R1B:
 202                 mmccmd |= SD_CMD_RT_1B;
 203                 break;
 204         case MMC_RSP_R2:
 205                 mmccmd |= SD_CMD_RT_2;
 206                 break;
 207         case MMC_RSP_R3:
 208                 mmccmd |= SD_CMD_RT_3;
 209                 break;
 210         }
 211
 212         switch(cmd->opcode) {
 213         case MMC_READ_SINGLE_BLOCK:
 214         case SD_APP_SEND_SCR:
 215                 mmccmd |= SD_CMD_CT_2;
 216                 break;
 217         case MMC_READ_MULTIPLE_BLOCK:
 218                 mmccmd |= SD_CMD_CT_4;
 219                 break;
 220         case MMC_WRITE_BLOCK:
 221                 mmccmd |= SD_CMD_CT_1;
 222                 break;
 223
 224         case MMC_WRITE_MULTIPLE_BLOCK:
 225                 mmccmd |= SD_CMD_CT_3;
 226                 break;
 227         case MMC_STOP_TRANSMISSION:
 228                 mmccmd |= SD_CMD_CT_7;
 229                 break;
 230         }
 231
 232         au_writel(cmd->arg, HOST_CMDARG(host));
 233         au_sync();
 234
 235         if (wait)
 236                 IRQ_OFF(host, SD_CONFIG_CR);
 237
 238         au_writel((mmccmd | SD_CMD_GO), HOST_CMD(host));
 239         au_sync();
 240
 241         /* Wait for the command to go on the line */
 242
 243         while(1) {
 244                 if (!(au_readl(HOST_CMD(host)) & SD_CMD_GO))
 245                         break;
 246         }
 247
 248         /* Wait for the command to come back */
 249
 250         if (wait) {
 251                 u32 status = au_readl(HOST_STATUS(host));
 252
 253                 while(!(status & SD_STATUS_CR))
 254                         status = au_readl(HOST_STATUS(host));
 255
 256                 /* Clear the CR status */
 257                 au_writel(SD_STATUS_CR, HOST_STATUS(host));
 258
 259                 IRQ_ON(host, SD_CONFIG_CR);
 260         }
 261
 262         return MMC_ERR_NONE;
 263 }
 264
 265 static void au1xmmc_data_complete(struct au1xmmc_host *host, u32 status)
 266 {
 267
 268         struct mmc_request *mrq = host->mrq;
 269         struct mmc_data *data;
 270         u32 crc;
 271
 272         WARN_ON(host->status != HOST_S_DATA && host->status != HOST_S_STOP);
 273
 274         if (host->mrq == NULL)
 275                 return;
 276
 277         data = mrq->cmd->data;
 278
 279         if (status == 0)
 280                 status = au_readl(HOST_STATUS(host));
 281
 282         /* The transaction is really over when the SD_STATUS_DB bit is clear */
 283
 284         while((host->flags & HOST_F_XMIT) && (status & SD_STATUS_DB))
 285                 status = au_readl(HOST_STATUS(host));
 286
 287         data->error = MMC_ERR_NONE;
 288         dma_unmap_sg(mmc_dev(host->mmc), data->sg, data->sg_len, host->dma.dir);
 289
 290         /* Process any errors */
 291
 292         crc = (status & (SD_STATUS_WC | SD_STATUS_RC));
 293         if (host->flags & HOST_F_XMIT)
 294                 crc |= ((status & 0x07) == 0x02) ? 0 : 1;
 295
 296         if (crc)
 297                 data->error = MMC_ERR_BADCRC;
 298
 299         /* Clear the CRC bits */
 300         au_writel(SD_STATUS_WC | SD_STATUS_RC, HOST_STATUS(host));
 301
 302         data->bytes_xfered = 0;
 303
 304         if (data->error == MMC_ERR_NONE) {
 305                 if (host->flags & HOST_F_DMA) {
 306                         u32 chan = DMA_CHANNEL(host);
 307
 308                         chan_tab_t *c = *((chan_tab_t **) chan);
 309                         au1x_dma_chan_t *cp = c->chan_ptr;
 310                         data->bytes_xfered = cp->ddma_bytecnt;
 311                 }
 312                 else
 313                         data->bytes_xfered =
 314                                 (data->blocks * (1 << data->blksz_bits)) -
 315                                 host->pio.len;
 316         }
 317
 318         au1xmmc_finish_request(host);
 319 }
 320
 321 static void au1xmmc_tasklet_data(unsigned long param)
 322 {
 323         struct au1xmmc_host *host = (struct au1xmmc_host *) param;
 324
 325         u32 status = au_readl(HOST_STATUS(host));
 326         au1xmmc_data_complete(host, status);
 327 }
 328
 329 #define AU1XMMC_MAX_TRANSFER 8
 330
 331 static void au1xmmc_send_pio(struct au1xmmc_host *host)
 332 {
 333
 334         struct mmc_data *data = 0;
 335         int sg_len, max, count = 0;
 336         unsigned char *sg_ptr;
 337         u32 status = 0;
 338         struct scatterlist *sg;
 339
 340         data = host->mrq->data;
 341
 342         if (!(host->flags & HOST_F_XMIT))
 343                 return;
 344
 345         /* This is the pointer to the data buffer */
 346         sg = &data->sg[host->pio.index];
 347         sg_ptr = page_address(sg->page) + sg->offset + host->pio.offset;
 348
 349         /* This is the space left inside the buffer */
 350         sg_len = data->sg[host->pio.index].length - host->pio.offset;
 351
 352         /* Check to if we need less then the size of the sg_buffer */
 353
 354         max = (sg_len > host->pio.len) ? host->pio.len : sg_len;
 355         if (max > AU1XMMC_MAX_TRANSFER) max = AU1XMMC_MAX_TRANSFER;
 356
 357         for(count = 0; count < max; count++ ) {
 358                 unsigned char val;
 359
 360                 status = au_readl(HOST_STATUS(host));
 361
 362                 if (!(status & SD_STATUS_TH))
 363                         break;
 364
 365                 val = *sg_ptr++;
 366
 367                 au_writel((unsigned long) val, HOST_TXPORT(host));
 368                 au_sync();
 369         }
 370
 371         host->pio.len -= count;
 372         host->pio.offset += count;
 373
 374         if (count == sg_len) {
 375                 host->pio.index++;
 376                 host->pio.offset = 0;
 377         }
 378
 379         if (host->pio.len == 0) {
 380                 IRQ_OFF(host, SD_CONFIG_TH);
 381
 382                 if (host->flags & HOST_F_STOP)
 383                         SEND_STOP(host);
 384
 385                 tasklet_schedule(&host->data_task);
 386         }
 387 }
 388
 389 static void au1xmmc_receive_pio(struct au1xmmc_host *host)
 390 {
 391
 392         struct mmc_data *data = 0;
 393         int sg_len = 0, max = 0, count = 0;
 394         unsigned char *sg_ptr = 0;
 395         u32 status = 0;
 396         struct scatterlist *sg;
 397
 398         data = host->mrq->data;
 399
 400         if (!(host->flags & HOST_F_RECV))
 401                 return;
 402
 403         max = host->pio.len;
 404
 405         if (host->pio.index < host->dma.len) {
 406                 sg = &data->sg[host->pio.index];
 407                 sg_ptr = page_address(sg->page) + sg->offset + host->pio.offset;
 408
 409                 /* This is the space left inside the buffer */
 410                 sg_len = sg_dma_len(&data->sg[host->pio.index]) - host->pio.offset;
 411
 412                 /* Check to if we need less then the size of the sg_buffer */
 413                 if (sg_len < max) max = sg_len;
 414         }
 415
 416         if (max > AU1XMMC_MAX_TRANSFER)
 417                 max = AU1XMMC_MAX_TRANSFER;
 418
 419         for(count = 0; count < max; count++ ) {
 420                 u32 val;
 421                 status = au_readl(HOST_STATUS(host));
 422
 423                 if (!(status & SD_STATUS_NE))
 424                         break;
 425
 426                 if (status & SD_STATUS_RC) {
 427                         DEBUG("RX CRC Error [%d + %d].\n", host->id,
 428                                         host->pio.len, count);
 429                         break;
 430                 }
 431
 432                 if (status & SD_STATUS_RO) {
 433                         DEBUG("RX Overrun [%d + %d]\n", host->id,
 434                                         host->pio.len, count);
 435                         break;
 436                 }
 437                 else if (status & SD_STATUS_RU) {
 438                         DEBUG("RX Underrun [%d + %d]\n", host->id,
 439                                         host->pio.len,  count);
 440                         break;
 441                 }
 442
 443                 val = au_readl(HOST_RXPORT(host));
 444
 445                 if (sg_ptr)
 446                         *sg_ptr++ = (unsigned char) (val & 0xFF);
 447         }
 448
 449         host->pio.len -= count;
 450         host->pio.offset += count;
 451
 452         if (sg_len && count == sg_len) {
 453                 host->pio.index++;
 454                 host->pio.offset = 0;
 455         }
 456
 457         if (host->pio.len == 0) {
 458                 //IRQ_OFF(host, SD_CONFIG_RA | SD_CONFIG_RF);
 459                 IRQ_OFF(host, SD_CONFIG_NE);
 460
 461                 if (host->flags & HOST_F_STOP)
 462                         SEND_STOP(host);
 463
 464                 tasklet_schedule(&host->data_task);
 465         }
 466 }
 467
 468 /* static void au1xmmc_cmd_complete
 469    This is called when a command has been completed - grab the response
 470    and check for errors.  Then start the data transfer if it is indicated.
 471 */
 472
 473 static void au1xmmc_cmd_complete(struct au1xmmc_host *host, u32 status)
 474 {
 475
 476         struct mmc_request *mrq = host->mrq;
 477         struct mmc_command *cmd;
 478         int trans;
 479
 480         if (!host->mrq)
 481                 return;
 482
 483         cmd = mrq->cmd;
 484         cmd->error = MMC_ERR_NONE;
 485
 486         if (cmd->flags & MMC_RSP_PRESENT) {
 487                 if (cmd->flags & MMC_RSP_136) {
 488                         u32 r[4];
 489                         int i;
 490
 491                         r[0] = au_readl(host->iobase + SD_RESP3);
 492                         r[1] = au_readl(host->iobase + SD_RESP2);
 493                         r[2] = au_readl(host->iobase + SD_RESP1);
 494                         r[3] = au_readl(host->iobase + SD_RESP0);
 495
 496                         /* The CRC is omitted from the response, so really
 497                          * we only got 120 bytes, but the engine expects
 498                          * 128 bits, so we have to shift things up
 499                          */
 500
 501                         for(i = 0; i < 4; i++) {
 502                                 cmd->resp[i] = (r[i] & 0x00FFFFFF) << 8;
 503                                 if (i != 3)
 504                                         cmd->resp[i] |= (r[i + 1] & 0xFF000000) >> 24;
 505                         }
 506                 } else {
 507                         /* Techincally, we should be getting all 48 bits of
 508                          * the response (SD_RESP1 + SD_RESP2), but because
 509                          * our response omits the CRC, our data ends up
 510                          * being shifted 8 bits to the right.  In this case,
 511                          * that means that the OSR data starts at bit 31,
 512                          * so we can just read RESP0 and return that
 513                          */
 514                         cmd->resp[0] = au_readl(host->iobase + SD_RESP0);
 515                 }
 516         }
 517
 518         /* Figure out errors */
 519
 520         if (status & (SD_STATUS_SC | SD_STATUS_WC | SD_STATUS_RC))
 521                 cmd->error = MMC_ERR_BADCRC;
 522
 523         trans = host->flags & (HOST_F_XMIT | HOST_F_RECV);
 524
 525         if (!trans || cmd->error != MMC_ERR_NONE) {
 526
 527                 IRQ_OFF(host, SD_CONFIG_TH | SD_CONFIG_RA|SD_CONFIG_RF);
 528                 tasklet_schedule(&host->finish_task);
 529                 return;
 530         }
 531
 532         host->status = HOST_S_DATA;
 533
 534         if (host->flags & HOST_F_DMA) {
 535                 u32 channel = DMA_CHANNEL(host);
 536
 537                 /* Start the DMA as soon as the buffer gets something in it */
 538
 539                 if (host->flags & HOST_F_RECV) {
 540                         u32 mask = SD_STATUS_DB | SD_STATUS_NE;
 541
 542                         while((status & mask) != mask)
 543                                 status = au_readl(HOST_STATUS(host));
 544                 }
 545
 546                 au1xxx_dbdma_start(channel);
 547         }
 548 }
 549
 550 static void au1xmmc_set_clock(struct au1xmmc_host *host, int rate)
 551 {
 552
 553         unsigned int pbus = get_au1x00_speed();
 554         unsigned int divisor;
 555         u32 config;
 556
 557         /* From databook:
 558            divisor = ((((cpuclock / sbus_divisor) / 2) / mmcclock) / 2) - 1
 559         */
 560
 561         pbus /= ((au_readl(SYS_POWERCTRL) & 0x3) + 2);
 562         pbus /= 2;
 563
 564         divisor = ((pbus / rate) / 2) - 1;
 565
 566         config = au_readl(HOST_CONFIG(host));
 567
 568         config &= ~(SD_CONFIG_DIV);
 569         config |= (divisor & SD_CONFIG_DIV) | SD_CONFIG_DE;
 570
 571         au_writel(config, HOST_CONFIG(host));
 572         au_sync();
 573 }
 574
 575 static int
 576 au1xmmc_prepare_data(struct au1xmmc_host *host, struct mmc_data *data)
 577 {
 578
 579         int datalen = data->blocks * (1 << data->blksz_bits);
 580
 581         if (dma != 0)
 582                 host->flags |= HOST_F_DMA;
 583
 584         if (data->flags & MMC_DATA_READ)
 585                 host->flags |= HOST_F_RECV;
 586         else
 587                 host->flags |= HOST_F_XMIT;
 588
 589         if (host->mrq->stop)
 590                 host->flags |= HOST_F_STOP;
 591
 592         host->dma.dir = DMA_BIDIRECTIONAL;
 593
 594         host->dma.len = dma_map_sg(mmc_dev(host->mmc), data->sg,
 595                                    data->sg_len, host->dma.dir);
 596
 597         if (host->dma.len == 0)
 598                 return MMC_ERR_TIMEOUT;
 599
 600         au_writel((1 << data->blksz_bits) - 1, HOST_BLKSIZE(host));
 601
 602         if (host->flags & HOST_F_DMA) {
 603                 int i;
 604                 u32 channel = DMA_CHANNEL(host);
 605
 606                 au1xxx_dbdma_stop(channel);
 607
 608                 for(i = 0; i < host->dma.len; i++) {
 609                         u32 ret = 0, flags = DDMA_FLAGS_NOIE;
 610                         struct scatterlist *sg = &data->sg[i];
 611                         int sg_len = sg->length;
 612
 613                         int len = (datalen > sg_len) ? sg_len : datalen;
 614
 615                         if (i == host->dma.len - 1)
 616                                 flags = DDMA_FLAGS_IE;
 617
 618                         if (host->flags & HOST_F_XMIT){
 619                                 ret = au1xxx_dbdma_put_source_flags(channel,
 620                                         (void *) (page_address(sg->page) +
 621                                                   sg->offset),
 622                                         len, flags);
 623                         }
 624                         else {
 625                                 ret = au1xxx_dbdma_put_dest_flags(channel,
 626                                         (void *) (page_address(sg->page) +
 627                                                   sg->offset),
 628                                         len, flags);
 629                         }
 630
 631                         if (!ret)
 632                                 goto dataerr;
 633
 634                         datalen -= len;
 635                 }
 636         }
 637         else {
 638                 host->pio.index = 0;
 639                 host->pio.offset = 0;
 640                 host->pio.len = datalen;
 641
 642                 if (host->flags & HOST_F_XMIT)
 643                         IRQ_ON(host, SD_CONFIG_TH);
 644                 else
 645                         IRQ_ON(host, SD_CONFIG_NE);
 646                         //IRQ_ON(host, SD_CONFIG_RA|SD_CONFIG_RF);
 647         }
 648
 649         return MMC_ERR_NONE;
 650
 651  dataerr:
 652         dma_unmap_sg(mmc_dev(host->mmc),data->sg,data->sg_len,host->dma.dir);
 653         return MMC_ERR_TIMEOUT;
 654 }
 655
 656 /* static void au1xmmc_request
 657    This actually starts a command or data transaction
 658 */
 659
 660 static void au1xmmc_request(struct mmc_host* mmc, struct mmc_request* mrq)
 661 {
 662
 663         struct au1xmmc_host *host = mmc_priv(mmc);
 664         int ret = MMC_ERR_NONE;
 665
 666         WARN_ON(irqs_disabled());
 667         WARN_ON(host->status != HOST_S_IDLE);
 668
 669         host->mrq = mrq;
 670         host->status = HOST_S_CMD;
 671
 672         bcsr->disk_leds &= ~(1 << 8);
 673
 674         if (mrq->data) {
 675                 FLUSH_FIFO(host);
 676                 ret = au1xmmc_prepare_data(host, mrq->data);
 677         }
 678
 679         if (ret == MMC_ERR_NONE)
 680                 ret = au1xmmc_send_command(host, 0, mrq->cmd);
 681
 682         if (ret != MMC_ERR_NONE) {
 683                 mrq->cmd->error = ret;
 684                 au1xmmc_finish_request(host);
 685         }
 686 }
 687
 688 static void au1xmmc_reset_controller(struct au1xmmc_host *host)
 689 {
 690
 691         /* Apply the clock */
 692         au_writel(SD_ENABLE_CE, HOST_ENABLE(host));
 693         au_sync_delay(1);
 694
 695         au_writel(SD_ENABLE_R | SD_ENABLE_CE, HOST_ENABLE(host));
 696         au_sync_delay(5);
 697
 698         au_writel(~0, HOST_STATUS(host));
 699         au_sync();
 700
 701         au_writel(0, HOST_BLKSIZE(host));
 702         au_writel(0x001fffff, HOST_TIMEOUT(host));
 703         au_sync();
 704
 705         au_writel(SD_CONFIG2_EN, HOST_CONFIG2(host));
 706         au_sync();
 707
 708         au_writel(SD_CONFIG2_EN | SD_CONFIG2_FF, HOST_CONFIG2(host));
 709         au_sync_delay(1);
 710
 711         au_writel(SD_CONFIG2_EN, HOST_CONFIG2(host));
 712         au_sync();
 713
 714         /* Configure interrupts */
 715         au_writel(AU1XMMC_INTERRUPTS, HOST_CONFIG(host));
 716         au_sync();
 717 }
 718
 719
 720 static void au1xmmc_set_ios(struct mmc_host* mmc, struct mmc_ios* ios)
 721 {
 722         struct au1xmmc_host *host = mmc_priv(mmc);
 723
 724         DEBUG("set_ios (power=%u, clock=%uHz, vdd=%u, mode=%u)\n",
 725               host->id, ios->power_mode, ios->clock, ios->vdd,
 726               ios->bus_mode);
 727
 728         if (ios->power_mode == MMC_POWER_OFF)
 729                 au1xmmc_set_power(host, 0);
 730         else if (ios->power_mode == MMC_POWER_ON) {
 731                 au1xmmc_set_power(host, 1);
 732         }
 733
 734         if (ios->clock && ios->clock != host->clock) {
 735                 au1xmmc_set_clock(host, ios->clock);
 736                 host->clock = ios->clock;
 737         }
 738 }
 739
 740 static void au1xmmc_dma_callback(int irq, void *dev_id, struct pt_regs *regs)
 741 {
 742         struct au1xmmc_host *host = (struct au1xmmc_host *) dev_id;
 743
 744         /* Avoid spurious interrupts */
 745
 746         if (!host->mrq)
 747                 return;
 748
 749         if (host->flags & HOST_F_STOP)
 750                 SEND_STOP(host);
 751
 752         tasklet_schedule(&host->data_task);
 753 }
 754
 755 #define STATUS_TIMEOUT (SD_STATUS_RAT | SD_STATUS_DT)
 756 #define STATUS_DATA_IN  (SD_STATUS_NE)
 757 #define STATUS_DATA_OUT (SD_STATUS_TH)
 758
 759 static irqreturn_t au1xmmc_irq(int irq, void *dev_id, struct pt_regs *regs)
 760 {
 761
 762         u32 status;
 763         int i, ret = 0;
 764
 765         disable_irq(AU1100_SD_IRQ);
 766
 767         for(i = 0; i < AU1XMMC_CONTROLLER_COUNT; i++) {
 768                 struct au1xmmc_host * host = au1xmmc_hosts[i];
 769                 u32 handled = 1;
 770
 771                 status = au_readl(HOST_STATUS(host));
 772
 773                 if (host->mrq && (status & STATUS_TIMEOUT)) {
 774                         if (status & SD_STATUS_RAT)
 775                                 host->mrq->cmd->error = MMC_ERR_TIMEOUT;
 776
 777                         else if (status & SD_STATUS_DT)
 778                                 host->mrq->data->error = MMC_ERR_TIMEOUT;
 779
 780                         /* In PIO mode, interrupts might still be enabled */
 781                         IRQ_OFF(host, SD_CONFIG_NE | SD_CONFIG_TH);
 782
 783                         //IRQ_OFF(host, SD_CONFIG_TH|SD_CONFIG_RA|SD_CONFIG_RF);
 784                         tasklet_schedule(&host->finish_task);
 785                 }
 786 #if 0
 787                 else if (status & SD_STATUS_DD) {
 788
 789                         /* Sometimes we get a DD before a NE in PIO mode */
 790
 791                         if (!(host->flags & HOST_F_DMA) &&
 792                                         (status & SD_STATUS_NE))
 793                                 au1xmmc_receive_pio(host);
 794                         else {
 795                                 au1xmmc_data_complete(host, status);
 796                                 //tasklet_schedule(&host->data_task);
 797                         }
 798                 }
 799 #endif
 800                 else if (status & (SD_STATUS_CR)) {
 801                         if (host->status == HOST_S_CMD)
 802                                 au1xmmc_cmd_complete(host,status);
 803                 }
 804                 else if (!(host->flags & HOST_F_DMA)) {
 805                         if ((host->flags & HOST_F_XMIT) &&
 806                             (status & STATUS_DATA_OUT))
 807                                 au1xmmc_send_pio(host);
 808                         else if ((host->flags & HOST_F_RECV) &&
 809                             (status & STATUS_DATA_IN))
 810                                 au1xmmc_receive_pio(host);
 811                 }
 812                 else if (status & 0x203FBC70) {
 813                         DEBUG("Unhandled status %8.8x\n", host->id, status);
 814                         handled = 0;
 815                 }
 816
 817                 au_writel(status, HOST_STATUS(host));
 818                 au_sync();
 819
 820                 ret |= handled;
 821         }
 822
 823         enable_irq(AU1100_SD_IRQ);
 824         return ret;
 825 }
 826
 827 static void au1xmmc_poll_event(unsigned long arg)
 828 {
 829         struct au1xmmc_host *host = (struct au1xmmc_host *) arg;
 830
 831         int card = au1xmmc_card_inserted(host);
 832         int controller = (host->flags & HOST_F_ACTIVE) ? 1 : 0;
 833
 834         if (card != controller) {
 835                 host->flags &= ~HOST_F_ACTIVE;
 836                 if (card) host->flags |= HOST_F_ACTIVE;
 837                 mmc_detect_change(host->mmc, 0);
 838         }
 839
 840         if (host->mrq != NULL) {
 841                 u32 status = au_readl(HOST_STATUS(host));
 842                 DEBUG("PENDING - %8.8x\n", host->id, status);
 843         }
 844
 845         mod_timer(&host->timer, jiffies + AU1XMMC_DETECT_TIMEOUT);
 846 }
 847
 848 static dbdev_tab_t au1xmmc_mem_dbdev =
 849 {
 850         DSCR_CMD0_ALWAYS, DEV_FLAGS_ANYUSE, 0, 8, 0x00000000, 0, 0
 851 };
 852
 853 static void au1xmmc_init_dma(struct au1xmmc_host *host)
 854 {
 855
 856         u32 rxchan, txchan;
 857
 858         int txid = au1xmmc_card_table[host->id].tx_devid;
 859         int rxid = au1xmmc_card_table[host->id].rx_devid;
 860
 861         /* DSCR_CMD0_ALWAYS has a stride of 32 bits, we need a stride
 862            of 8 bits.  And since devices are shared, we need to create
 863            our own to avoid freaking out other devices
 864         */
 865
 866         int memid = au1xxx_ddma_add_device(&au1xmmc_mem_dbdev);
 867
 868         txchan = au1xxx_dbdma_chan_alloc(memid, txid,
 869                                          au1xmmc_dma_callback, (void *) host);
 870
 871         rxchan = au1xxx_dbdma_chan_alloc(rxid, memid,
 872                                          au1xmmc_dma_callback, (void *) host);
 873
 874         au1xxx_dbdma_set_devwidth(txchan, 8);
 875         au1xxx_dbdma_set_devwidth(rxchan, 8);
 876
 877         au1xxx_dbdma_ring_alloc(txchan, AU1XMMC_DESCRIPTOR_COUNT);
 878         au1xxx_dbdma_ring_alloc(rxchan, AU1XMMC_DESCRIPTOR_COUNT);
 879
 880         host->tx_chan = txchan;
 881         host->rx_chan = rxchan;
 882 }
 883
 884 struct mmc_host_ops au1xmmc_ops = {
 885         .request        = au1xmmc_request,
 886         .set_ios        = au1xmmc_set_ios,
 887 };
 888
 889 static int __devinit au1xmmc_probe(struct platform_device *pdev)
 890 {
 891
 892         int i, ret = 0;
 893
 894         /* THe interrupt is shared among all controllers */
 895         ret = request_irq(AU1100_SD_IRQ, au1xmmc_irq, SA_INTERRUPT, "MMC", 0);
 896
 897         if (ret) {
 898                 printk(DRIVER_NAME "ERROR: Couldn't get int %d: %d\n",
 899                                 AU1100_SD_IRQ, ret);
 900                 return -ENXIO;
 901         }
 902
 903         disable_irq(AU1100_SD_IRQ);
 904
 905         for(i = 0; i < AU1XMMC_CONTROLLER_COUNT; i++) {
 906                 struct mmc_host *mmc = mmc_alloc_host(sizeof(struct au1xmmc_host), &pdev->dev);
 907                 struct au1xmmc_host *host = 0;
 908
 909                 if (!mmc) {
 910                         printk(DRIVER_NAME "ERROR: no mem for host %d\n", i);
 911                         au1xmmc_hosts[i] = 0;
 912                         continue;
 913                 }
 914
 915                 mmc->ops = &au1xmmc_ops;
 916
 917                 mmc->f_min =   450000;
 918                 mmc->f_max = 24000000;
 919
 920                 mmc->max_seg_size = AU1XMMC_DESCRIPTOR_SIZE;
 921                 mmc->max_phys_segs = AU1XMMC_DESCRIPTOR_COUNT;
 922
 923                 mmc->ocr_avail = AU1XMMC_OCR;
 924
 925                 host = mmc_priv(mmc);
 926                 host->mmc = mmc;
 927
 928                 host->id = i;
 929                 host->iobase = au1xmmc_card_table[host->id].iobase;
 930                 host->clock = 0;
 931                 host->power_mode = MMC_POWER_OFF;
 932
 933                 host->flags = au1xmmc_card_inserted(host) ? HOST_F_ACTIVE : 0;
 934                 host->status = HOST_S_IDLE;
 935
 936                 init_timer(&host->timer);
 937
 938                 host->timer.function = au1xmmc_poll_event;
 939                 host->timer.data = (unsigned long) host;
 940                 host->timer.expires = jiffies + AU1XMMC_DETECT_TIMEOUT;
 941
 942                 tasklet_init(&host->data_task, au1xmmc_tasklet_data,
 943                                 (unsigned long) host);
 944
 945                 tasklet_init(&host->finish_task, au1xmmc_tasklet_finish,
 946                                 (unsigned long) host);
 947
 948                 spin_lock_init(&host->lock);
 949
 950                 if (dma != 0)
 951                         au1xmmc_init_dma(host);
 952
 953                 au1xmmc_reset_controller(host);
 954
 955                 mmc_add_host(mmc);
 956                 au1xmmc_hosts[i] = host;
 957
 958                 add_timer(&host->timer);
 959
 960                 printk(KERN_INFO DRIVER_NAME ": MMC Controller %d set up at %8.8X (mode=%s)\n",
 961                        host->id, host->iobase, dma ? "dma" : "pio");
 962         }
 963
 964         enable_irq(AU1100_SD_IRQ);
 965
 966         return 0;
 967 }
 968
 969 static int __devexit au1xmmc_remove(struct platform_device *pdev)
 970 {
 971
 972         int i;
 973
 974         disable_irq(AU1100_SD_IRQ);
 975
 976         for(i = 0; i < AU1XMMC_CONTROLLER_COUNT; i++) {
 977                 struct au1xmmc_host *host = au1xmmc_hosts[i];
 978                 if (!host) continue;
 979
 980                 tasklet_kill(&host->data_task);
 981                 tasklet_kill(&host->finish_task);
 982
 983                 del_timer_sync(&host->timer);
 984                 au1xmmc_set_power(host, 0);
 985
 986                 mmc_remove_host(host->mmc);
 987
 988                 au1xxx_dbdma_chan_free(host->tx_chan);
 989                 au1xxx_dbdma_chan_free(host->rx_chan);
 990
 991                 au_writel(0x0, HOST_ENABLE(host));
 992                 au_sync();
 993         }
 994
 995         free_irq(AU1100_SD_IRQ, 0);
 996         return 0;
 997 }
 998
 999 static struct platform_driver au1xmmc_driver = {
1000         .probe         = au1xmmc_probe,
1001         .remove        = au1xmmc_remove,
1002         .suspend       = NULL,
1003         .resume        = NULL,
1004         .driver        = {
1005                 .name  = DRIVER_NAME,
1006         },
1007 };
1008
1009 static int __init au1xmmc_init(void)
1010 {
1011         return platform_driver_register(&au1xmmc_driver);
1012 }
1013
1014 static void __exit au1xmmc_exit(void)
1015 {
1016         platform_driver_unregister(&au1xmmc_driver);
1017 }
1018
1019 module_init(au1xmmc_init);
1020 module_exit(au1xmmc_exit);
1021
1022 #ifdef MODULE
1023 MODULE_AUTHOR("Advanced Micro Devices, Inc");
1024 MODULE_DESCRIPTION("MMC/SD driver for the Alchemy Au1XXX");
1025 MODULE_LICENSE("GPL");
1026 #endif
1027