git.oblomov.eu Git - linux-2.6/blob - drivers/net/irda/irda-usb.c

   1 /*****************************************************************************
   2  *
   3  * Filename:      irda-usb.c
   4  * Version:       0.10
   5  * Description:   IrDA-USB Driver
   6  * Status:        Experimental
   7  * Author:        Dag Brattli <dag@brattli.net>
   8  *
   9  *      Copyright (C) 2000, Roman Weissgaerber <weissg@vienna.at>
  10  *      Copyright (C) 2001, Dag Brattli <dag@brattli.net>
  11  *      Copyright (C) 2001, Jean Tourrilhes <jt@hpl.hp.com>
  12  *      Copyright (C) 2004, SigmaTel, Inc. <irquality@sigmatel.com>
  13  *      Copyright (C) 2005, Milan Beno <beno@pobox.sk>
  14  *      Copyright (C) 2006, Nick Fedchik <nick@fedchik.org.ua>
  15  *
  16  *      This program is free software; you can redistribute it and/or modify
  17  *      it under the terms of the GNU General Public License as published by
  18  *      the Free Software Foundation; either version 2 of the License, or
  19  *      (at your option) any later version.
  20  *
  21  *      This program is distributed in the hope that it will be useful,
  22  *      but WITHOUT ANY WARRANTY; without even the implied warranty of
  23  *      MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
  24  *      GNU General Public License for more details.
  25  *
  26  *      You should have received a copy of the GNU General Public License
  27  *      along with this program; if not, write to the Free Software
  28  *      Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA.
  29  *
  30  *****************************************************************************/
  31
  32 /*
  33  *                          IMPORTANT NOTE
  34  *                          --------------
  35  *
  36  * As of kernel 2.5.20, this is the state of compliance and testing of
  37  * this driver (irda-usb) with regards to the USB low level drivers...
  38  *
  39  * This driver has been tested SUCCESSFULLY with the following drivers :
  40  *      o usb-uhci-hcd  (For Intel/Via USB controllers)
  41  *      o uhci-hcd      (Alternate/JE driver for Intel/Via USB controllers)
  42  *      o ohci-hcd      (For other USB controllers)
  43  *
  44  * This driver has NOT been tested with the following drivers :
  45  *      o ehci-hcd      (USB 2.0 controllers)
  46  *
  47  * Note that all HCD drivers do URB_ZERO_PACKET and timeout properly,
  48  * so we don't have to worry about that anymore.
  49  * One common problem is the failure to set the address on the dongle,
  50  * but this happens before the driver gets loaded...
  51  *
  52  * Jean II
  53  */
  54
  55 /*------------------------------------------------------------------*/
  56
  57 #include <linux/module.h>
  58 #include <linux/moduleparam.h>
  59 #include <linux/kernel.h>
  60 #include <linux/types.h>
  61 #include <linux/init.h>
  62 #include <linux/skbuff.h>
  63 #include <linux/netdevice.h>
  64 #include <linux/slab.h>
  65 #include <linux/rtnetlink.h>
  66 #include <linux/usb.h>
  67 #include <linux/firmware.h>
  68
  69 #include "irda-usb.h"
  70
  71 /*------------------------------------------------------------------*/
  72
  73 static int qos_mtt_bits = 0;
  74
  75 /* These are the currently known IrDA USB dongles. Add new dongles here */
  76 static struct usb_device_id dongles[] = {
  77         /* ACTiSYS Corp.,  ACT-IR2000U FIR-USB Adapter */
  78         { USB_DEVICE(0x9c4, 0x011), .driver_info = IUC_SPEED_BUG | IUC_NO_WINDOW },
  79         /* Look like ACTiSYS, Report : IBM Corp., IBM UltraPort IrDA */
  80         { USB_DEVICE(0x4428, 0x012), .driver_info = IUC_SPEED_BUG | IUC_NO_WINDOW },
  81         /* KC Technology Inc.,  KC-180 USB IrDA Device */
  82         { USB_DEVICE(0x50f, 0x180), .driver_info = IUC_SPEED_BUG | IUC_NO_WINDOW },
  83         /* Extended Systems, Inc.,  XTNDAccess IrDA USB (ESI-9685) */
  84         { USB_DEVICE(0x8e9, 0x100), .driver_info = IUC_SPEED_BUG | IUC_NO_WINDOW },
  85         /* SigmaTel STIR4210/4220/4116 USB IrDA (VFIR) Bridge */
  86         { USB_DEVICE(0x66f, 0x4210), .driver_info = IUC_STIR421X | IUC_SPEED_BUG },
  87         { USB_DEVICE(0x66f, 0x4220), .driver_info = IUC_STIR421X | IUC_SPEED_BUG },
  88         { USB_DEVICE(0x66f, 0x4116), .driver_info = IUC_STIR421X | IUC_SPEED_BUG },
  89         { .match_flags = USB_DEVICE_ID_MATCH_INT_CLASS |
  90           USB_DEVICE_ID_MATCH_INT_SUBCLASS,
  91           .bInterfaceClass = USB_CLASS_APP_SPEC,
  92           .bInterfaceSubClass = USB_CLASS_IRDA,
  93           .driver_info = IUC_DEFAULT, },
  94         { }, /* The end */
  95 };
  96
  97 /*
  98  * Important note :
  99  * Devices based on the SigmaTel chipset (0x66f, 0x4200) are not designed
 100  * using the "USB-IrDA specification" (yes, there exist such a thing), and
 101  * therefore not supported by this driver (don't add them above).
 102  * There is a Linux driver, stir4200, that support those USB devices.
 103  * Jean II
 104  */
 105
 106 MODULE_DEVICE_TABLE(usb, dongles);
 107
 108 /*------------------------------------------------------------------*/
 109
 110 static void irda_usb_init_qos(struct irda_usb_cb *self) ;
 111 static struct irda_class_desc *irda_usb_find_class_desc(struct usb_interface *intf);
 112 static void irda_usb_disconnect(struct usb_interface *intf);
 113 static void irda_usb_change_speed_xbofs(struct irda_usb_cb *self);
 114 static int irda_usb_hard_xmit(struct sk_buff *skb, struct net_device *dev);
 115 static int irda_usb_open(struct irda_usb_cb *self);
 116 static void irda_usb_close(struct irda_usb_cb *self);
 117 static void speed_bulk_callback(struct urb *urb);
 118 static void write_bulk_callback(struct urb *urb);
 119 static void irda_usb_receive(struct urb *urb);
 120 static void irda_usb_rx_defer_expired(unsigned long data);
 121 static int irda_usb_net_open(struct net_device *dev);
 122 static int irda_usb_net_close(struct net_device *dev);
 123 static int irda_usb_net_ioctl(struct net_device *dev, struct ifreq *rq, int cmd);
 124 static void irda_usb_net_timeout(struct net_device *dev);
 125 static struct net_device_stats *irda_usb_net_get_stats(struct net_device *dev);
 126
 127 /************************ TRANSMIT ROUTINES ************************/
 128 /*
 129  * Receive packets from the IrDA stack and send them on the USB pipe.
 130  * Handle speed change, timeout and lot's of ugliness...
 131  */
 132
 133 /*------------------------------------------------------------------*/
 134 /*
 135  * Function irda_usb_build_header(self, skb, header)
 136  *
 137  *   Builds USB-IrDA outbound header
 138  *
 139  * When we send an IrDA frame over an USB pipe, we add to it a 1 byte
 140  * header. This function create this header with the proper values.
 141  *
 142  * Important note : the USB-IrDA spec 1.0 say very clearly in chapter 5.4.2.2
 143  * that the setting of the link speed and xbof number in this outbound header
 144  * should be applied *AFTER* the frame has been sent.
 145  * Unfortunately, some devices are not compliant with that... It seems that
 146  * reading the spec is far too difficult...
 147  * Jean II
 148  */
 149 static void irda_usb_build_header(struct irda_usb_cb *self,
 150                                   __u8 *header,
 151                                   int   force)
 152 {
 153         /* Here we check if we have an STIR421x chip,
 154          * and if either speed or xbofs (or both) needs
 155          * to be changed.
 156          */
 157         if (self->capability & IUC_STIR421X &&
 158             ((self->new_speed != -1) || (self->new_xbofs != -1))) {
 159
 160                 /* With STIR421x, speed and xBOFs must be set at the same
 161                  * time, even if only one of them changes.
 162                  */
 163                 if (self->new_speed == -1)
 164                         self->new_speed = self->speed ;
 165
 166                 if (self->new_xbofs == -1)
 167                         self->new_xbofs = self->xbofs ;
 168         }
 169
 170         /* Set the link speed */
 171         if (self->new_speed != -1) {
 172                 /* Hum... Ugly hack :-(
 173                  * Some device are not compliant with the spec and change
 174                  * parameters *before* sending the frame. - Jean II
 175                  */
 176                 if ((self->capability & IUC_SPEED_BUG) &&
 177                     (!force) && (self->speed != -1)) {
 178                         /* No speed and xbofs change here
 179                          * (we'll do it later in the write callback) */
 180                         IRDA_DEBUG(2, "%s(), not changing speed yet\n", __func__);
 181                         *header = 0;
 182                         return;
 183                 }
 184
 185                 IRDA_DEBUG(2, "%s(), changing speed to %d\n", __func__, self->new_speed);
 186                 self->speed = self->new_speed;
 187                 /* We will do ` self->new_speed = -1; ' in the completion
 188                  * handler just in case the current URB fail - Jean II */
 189
 190                 switch (self->speed) {
 191                 case 2400:
 192                         *header = SPEED_2400;
 193                         break;
 194                 default:
 195                 case 9600:
 196                         *header = SPEED_9600;
 197                         break;
 198                 case 19200:
 199                         *header = SPEED_19200;
 200                         break;
 201                 case 38400:
 202                         *header = SPEED_38400;
 203                         break;
 204                 case 57600:
 205                         *header = SPEED_57600;
 206                         break;
 207                 case 115200:
 208                         *header = SPEED_115200;
 209                         break;
 210                 case 576000:
 211                         *header = SPEED_576000;
 212                         break;
 213                 case 1152000:
 214                         *header = SPEED_1152000;
 215                         break;
 216                 case 4000000:
 217                         *header = SPEED_4000000;
 218                         self->new_xbofs = 0;
 219                         break;
 220                 case 16000000:
 221                         *header = SPEED_16000000;
 222                         self->new_xbofs = 0;
 223                         break;
 224                 }
 225         } else
 226                 /* No change */
 227                 *header = 0;
 228
 229         /* Set the negotiated additional XBOFS */
 230         if (self->new_xbofs != -1) {
 231                 IRDA_DEBUG(2, "%s(), changing xbofs to %d\n", __func__, self->new_xbofs);
 232                 self->xbofs = self->new_xbofs;
 233                 /* We will do ` self->new_xbofs = -1; ' in the completion
 234                  * handler just in case the current URB fail - Jean II */
 235
 236                 switch (self->xbofs) {
 237                 case 48:
 238                         *header |= 0x10;
 239                         break;
 240                 case 28:
 241                 case 24:        /* USB spec 1.0 says 24 */
 242                         *header |= 0x20;
 243                         break;
 244                 default:
 245                 case 12:
 246                         *header |= 0x30;
 247                         break;
 248                 case 5: /* Bug in IrLAP spec? (should be 6) */
 249                 case 6:
 250                         *header |= 0x40;
 251                         break;
 252                 case 3:
 253                         *header |= 0x50;
 254                         break;
 255                 case 2:
 256                         *header |= 0x60;
 257                         break;
 258                 case 1:
 259                         *header |= 0x70;
 260                         break;
 261                 case 0:
 262                         *header |= 0x80;
 263                         break;
 264                 }
 265         }
 266 }
 267
 268 /*
 269 *   calculate turnaround time for SigmaTel header
 270 */
 271 static __u8 get_turnaround_time(struct sk_buff *skb)
 272 {
 273         int turnaround_time = irda_get_mtt(skb);
 274
 275         if ( turnaround_time == 0 )
 276                 return 0;
 277         else if ( turnaround_time <= 10 )
 278                 return 1;
 279         else if ( turnaround_time <= 50 )
 280                 return 2;
 281         else if ( turnaround_time <= 100 )
 282                 return 3;
 283         else if ( turnaround_time <= 500 )
 284                 return 4;
 285         else if ( turnaround_time <= 1000 )
 286                 return 5;
 287         else if ( turnaround_time <= 5000 )
 288                 return 6;
 289         else
 290                 return 7;
 291 }
 292
 293
 294 /*------------------------------------------------------------------*/
 295 /*
 296  * Send a command to change the speed of the dongle
 297  * Need to be called with spinlock on.
 298  */
 299 static void irda_usb_change_speed_xbofs(struct irda_usb_cb *self)
 300 {
 301         __u8 *frame;
 302         struct urb *urb;
 303         int ret;
 304
 305         IRDA_DEBUG(2, "%s(), speed=%d, xbofs=%d\n", __func__,
 306                    self->new_speed, self->new_xbofs);
 307
 308         /* Grab the speed URB */
 309         urb = self->speed_urb;
 310         if (urb->status != 0) {
 311                 IRDA_WARNING("%s(), URB still in use!\n", __func__);
 312                 return;
 313         }
 314
 315         /* Allocate the fake frame */
 316         frame = self->speed_buff;
 317
 318         /* Set the new speed and xbofs in this fake frame */
 319         irda_usb_build_header(self, frame, 1);
 320
 321         if (self->capability & IUC_STIR421X) {
 322                 if (frame[0] == 0) return ; // do nothing if no change
 323                 frame[1] = 0; // other parameters don't change here
 324                 frame[2] = 0;
 325         }
 326
 327         /* Submit the 0 length IrDA frame to trigger new speed settings */
 328         usb_fill_bulk_urb(urb, self->usbdev,
 329                       usb_sndbulkpipe(self->usbdev, self->bulk_out_ep),
 330                       frame, IRDA_USB_SPEED_MTU,
 331                       speed_bulk_callback, self);
 332         urb->transfer_buffer_length = self->header_length;
 333         urb->transfer_flags = 0;
 334
 335         /* Irq disabled -> GFP_ATOMIC */
 336         if ((ret = usb_submit_urb(urb, GFP_ATOMIC))) {
 337                 IRDA_WARNING("%s(), failed Speed URB\n", __func__);
 338         }
 339 }
 340
 341 /*------------------------------------------------------------------*/
 342 /*
 343  * Speed URB callback
 344  * Now, we can only get called for the speed URB.
 345  */
 346 static void speed_bulk_callback(struct urb *urb)
 347 {
 348         struct irda_usb_cb *self = urb->context;
 349
 350         IRDA_DEBUG(2, "%s()\n", __func__);
 351
 352         /* We should always have a context */
 353         IRDA_ASSERT(self != NULL, return;);
 354         /* We should always be called for the speed URB */
 355         IRDA_ASSERT(urb == self->speed_urb, return;);
 356
 357         /* Check for timeout and other USB nasties */
 358         if (urb->status != 0) {
 359                 /* I get a lot of -ECONNABORTED = -103 here - Jean II */
 360                 IRDA_DEBUG(0, "%s(), URB complete status %d, transfer_flags 0x%04X\n", __func__, urb->status, urb->transfer_flags);
 361
 362                 /* Don't do anything here, that might confuse the USB layer.
 363                  * Instead, we will wait for irda_usb_net_timeout(), the
 364                  * network layer watchdog, to fix the situation.
 365                  * Jean II */
 366                 /* A reset of the dongle might be welcomed here - Jean II */
 367                 return;
 368         }
 369
 370         /* urb is now available */
 371         //urb->status = 0; -> tested above
 372
 373         /* New speed and xbof is now commited in hardware */
 374         self->new_speed = -1;
 375         self->new_xbofs = -1;
 376
 377         /* Allow the stack to send more packets */
 378         netif_wake_queue(self->netdev);
 379 }
 380
 381 /*------------------------------------------------------------------*/
 382 /*
 383  * Send an IrDA frame to the USB dongle (for transmission)
 384  */
 385 static int irda_usb_hard_xmit(struct sk_buff *skb, struct net_device *netdev)
 386 {
 387         struct irda_usb_cb *self = netdev_priv(netdev);
 388         struct urb *urb = self->tx_urb;
 389         unsigned long flags;
 390         s32 speed;
 391         s16 xbofs;
 392         int res, mtt;
 393         int     err = 1;        /* Failed */
 394
 395         IRDA_DEBUG(4, "%s() on %s\n", __func__, netdev->name);
 396
 397         netif_stop_queue(netdev);
 398
 399         /* Protect us from USB callbacks, net watchdog and else. */
 400         spin_lock_irqsave(&self->lock, flags);
 401
 402         /* Check if the device is still there.
 403          * We need to check self->present under the spinlock because
 404          * of irda_usb_disconnect() is synchronous - Jean II */
 405         if (!self->present) {
 406                 IRDA_DEBUG(0, "%s(), Device is gone...\n", __func__);
 407                 goto drop;
 408         }
 409
 410         /* Check if we need to change the number of xbofs */
 411         xbofs = irda_get_next_xbofs(skb);
 412         if ((xbofs != self->xbofs) && (xbofs != -1)) {
 413                 self->new_xbofs = xbofs;
 414         }
 415
 416         /* Check if we need to change the speed */
 417         speed = irda_get_next_speed(skb);
 418         if ((speed != self->speed) && (speed != -1)) {
 419                 /* Set the desired speed */
 420                 self->new_speed = speed;
 421
 422                 /* Check for empty frame */
 423                 if (!skb->len) {
 424                         /* IrLAP send us an empty frame to make us change the
 425                          * speed. Changing speed with the USB adapter is in
 426                          * fact sending an empty frame to the adapter, so we
 427                          * could just let the present function do its job.
 428                          * However, we would wait for min turn time,
 429                          * do an extra memcpy and increment packet counters...
 430                          * Jean II */
 431                         irda_usb_change_speed_xbofs(self);
 432                         netdev->trans_start = jiffies;
 433                         /* Will netif_wake_queue() in callback */
 434                         err = 0;        /* No error */
 435                         goto drop;
 436                 }
 437         }
 438
 439         if (urb->status != 0) {
 440                 IRDA_WARNING("%s(), URB still in use!\n", __func__);
 441                 goto drop;
 442         }
 443
 444         skb_copy_from_linear_data(skb, self->tx_buff + self->header_length, skb->len);
 445
 446         /* Change setting for next frame */
 447         if (self->capability & IUC_STIR421X) {
 448                 __u8 turnaround_time;
 449                 __u8* frame = self->tx_buff;
 450                 turnaround_time = get_turnaround_time( skb );
 451                 irda_usb_build_header(self, frame, 0);
 452                 frame[2] = turnaround_time;
 453                 if ((skb->len != 0) &&
 454                     ((skb->len % 128) == 0) &&
 455                     ((skb->len % 512) != 0)) {
 456                         /* add extra byte for special SigmaTel feature */
 457                         frame[1] = 1;
 458                         skb_put(skb, 1);
 459                 } else {
 460                         frame[1] = 0;
 461                 }
 462         } else {
 463                 irda_usb_build_header(self, self->tx_buff, 0);
 464         }
 465
 466         /* FIXME: Make macro out of this one */
 467         ((struct irda_skb_cb *)skb->cb)->context = self;
 468
 469         usb_fill_bulk_urb(urb, self->usbdev,
 470                       usb_sndbulkpipe(self->usbdev, self->bulk_out_ep),
 471                       self->tx_buff, skb->len + self->header_length,
 472                       write_bulk_callback, skb);
 473
 474         /* This flag (URB_ZERO_PACKET) indicates that what we send is not
 475          * a continuous stream of data but separate packets.
 476          * In this case, the USB layer will insert an empty USB frame (TD)
 477          * after each of our packets that is exact multiple of the frame size.
 478          * This is how the dongle will detect the end of packet - Jean II */
 479         urb->transfer_flags = URB_ZERO_PACKET;
 480
 481         /* Generate min turn time. FIXME: can we do better than this? */
 482         /* Trying to a turnaround time at this level is trying to measure
 483          * processor clock cycle with a wrist-watch, approximate at best...
 484          *
 485          * What we know is the last time we received a frame over USB.
 486          * Due to latency over USB that depend on the USB load, we don't
 487          * know when this frame was received over IrDA (a few ms before ?)
 488          * Then, same story for our outgoing frame...
 489          *
 490          * In theory, the USB dongle is supposed to handle the turnaround
 491          * by itself (spec 1.0, chater 4, page 6). Who knows ??? That's
 492          * why this code is enabled only for dongles that doesn't meet
 493          * the spec.
 494          * Jean II */
 495         if (self->capability & IUC_NO_TURN) {
 496                 mtt = irda_get_mtt(skb);
 497                 if (mtt) {
 498                         int diff;
 499                         do_gettimeofday(&self->now);
 500                         diff = self->now.tv_usec - self->stamp.tv_usec;
 501 #ifdef IU_USB_MIN_RTT
 502                         /* Factor in USB delays -> Get rid of udelay() that
 503                          * would be lost in the noise - Jean II */
 504                         diff += IU_USB_MIN_RTT;
 505 #endif /* IU_USB_MIN_RTT */
 506                         /* If the usec counter did wraparound, the diff will
 507                          * go negative (tv_usec is a long), so we need to
 508                          * correct it by one second. Jean II */
 509                         if (diff < 0)
 510                                 diff += 1000000;
 511
 512                         /* Check if the mtt is larger than the time we have
 513                          * already used by all the protocol processing
 514                          */
 515                         if (mtt > diff) {
 516                                 mtt -= diff;
 517                                 if (mtt > 1000)
 518                                         mdelay(mtt/1000);
 519                                 else
 520                                         udelay(mtt);
 521                         }
 522                 }
 523         }
 524
 525         /* Ask USB to send the packet - Irq disabled -> GFP_ATOMIC */
 526         if ((res = usb_submit_urb(urb, GFP_ATOMIC))) {
 527                 IRDA_WARNING("%s(), failed Tx URB\n", __func__);
 528                 self->stats.tx_errors++;
 529                 /* Let USB recover : We will catch that in the watchdog */
 530                 /*netif_start_queue(netdev);*/
 531         } else {
 532                 /* Increment packet stats */
 533                 self->stats.tx_packets++;
 534                 self->stats.tx_bytes += skb->len;
 535
 536                 netdev->trans_start = jiffies;
 537         }
 538         spin_unlock_irqrestore(&self->lock, flags);
 539
 540         return 0;
 541
 542 drop:
 543         /* Drop silently the skb and exit */
 544         dev_kfree_skb(skb);
 545         spin_unlock_irqrestore(&self->lock, flags);
 546         return err;             /* Usually 1 */
 547 }
 548
 549 /*------------------------------------------------------------------*/
 550 /*
 551  * Note : this function will be called only for tx_urb...
 552  */
 553 static void write_bulk_callback(struct urb *urb)
 554 {
 555         unsigned long flags;
 556         struct sk_buff *skb = urb->context;
 557         struct irda_usb_cb *self = ((struct irda_skb_cb *) skb->cb)->context;
 558
 559         IRDA_DEBUG(2, "%s()\n", __func__);
 560
 561         /* We should always have a context */
 562         IRDA_ASSERT(self != NULL, return;);
 563         /* We should always be called for the speed URB */
 564         IRDA_ASSERT(urb == self->tx_urb, return;);
 565
 566         /* Free up the skb */
 567         dev_kfree_skb_any(skb);
 568         urb->context = NULL;
 569
 570         /* Check for timeout and other USB nasties */
 571         if (urb->status != 0) {
 572                 /* I get a lot of -ECONNABORTED = -103 here - Jean II */
 573                 IRDA_DEBUG(0, "%s(), URB complete status %d, transfer_flags 0x%04X\n", __func__, urb->status, urb->transfer_flags);
 574
 575                 /* Don't do anything here, that might confuse the USB layer,
 576                  * and we could go in recursion and blow the kernel stack...
 577                  * Instead, we will wait for irda_usb_net_timeout(), the
 578                  * network layer watchdog, to fix the situation.
 579                  * Jean II */
 580                 /* A reset of the dongle might be welcomed here - Jean II */
 581                 return;
 582         }
 583
 584         /* urb is now available */
 585         //urb->status = 0; -> tested above
 586
 587         /* Make sure we read self->present properly */
 588         spin_lock_irqsave(&self->lock, flags);
 589
 590         /* If the network is closed, stop everything */
 591         if ((!self->netopen) || (!self->present)) {
 592                 IRDA_DEBUG(0, "%s(), Network is gone...\n", __func__);
 593                 spin_unlock_irqrestore(&self->lock, flags);
 594                 return;
 595         }
 596
 597         /* If changes to speed or xbofs is pending... */
 598         if ((self->new_speed != -1) || (self->new_xbofs != -1)) {
 599                 if ((self->new_speed != self->speed) ||
 600                     (self->new_xbofs != self->xbofs)) {
 601                         /* We haven't changed speed yet (because of
 602                          * IUC_SPEED_BUG), so do it now - Jean II */
 603                         IRDA_DEBUG(1, "%s(), Changing speed now...\n", __func__);
 604                         irda_usb_change_speed_xbofs(self);
 605                 } else {
 606                         /* New speed and xbof is now commited in hardware */
 607                         self->new_speed = -1;
 608                         self->new_xbofs = -1;
 609                         /* Done, waiting for next packet */
 610                         netif_wake_queue(self->netdev);
 611                 }
 612         } else {
 613                 /* Otherwise, allow the stack to send more packets */
 614                 netif_wake_queue(self->netdev);
 615         }
 616         spin_unlock_irqrestore(&self->lock, flags);
 617 }
 618
 619 /*------------------------------------------------------------------*/
 620 /*
 621  * Watchdog timer from the network layer.
 622  * After a predetermined timeout, if we don't give confirmation that
 623  * the packet has been sent (i.e. no call to netif_wake_queue()),
 624  * the network layer will call this function.
 625  * Note that URB that we submit have also a timeout. When the URB timeout
 626  * expire, the normal URB callback is called (write_bulk_callback()).
 627  */
 628 static void irda_usb_net_timeout(struct net_device *netdev)
 629 {
 630         unsigned long flags;
 631         struct irda_usb_cb *self = netdev_priv(netdev);
 632         struct urb *urb;
 633         int     done = 0;       /* If we have made any progress */
 634
 635         IRDA_DEBUG(0, "%s(), Network layer thinks we timed out!\n", __func__);
 636         IRDA_ASSERT(self != NULL, return;);
 637
 638         /* Protect us from USB callbacks, net Tx and else. */
 639         spin_lock_irqsave(&self->lock, flags);
 640
 641         /* self->present *MUST* be read under spinlock */
 642         if (!self->present) {
 643                 IRDA_WARNING("%s(), device not present!\n", __func__);
 644                 netif_stop_queue(netdev);
 645                 spin_unlock_irqrestore(&self->lock, flags);
 646                 return;
 647         }
 648
 649         /* Check speed URB */
 650         urb = self->speed_urb;
 651         if (urb->status != 0) {
 652                 IRDA_DEBUG(0, "%s: Speed change timed out, urb->status=%d, urb->transfer_flags=0x%04X\n", netdev->name, urb->status, urb->transfer_flags);
 653
 654                 switch (urb->status) {
 655                 case -EINPROGRESS:
 656                         usb_unlink_urb(urb);
 657                         /* Note : above will  *NOT* call netif_wake_queue()
 658                          * in completion handler, we will come back here.
 659                          * Jean II */
 660                         done = 1;
 661                         break;
 662                 case -ECONNRESET:
 663                 case -ENOENT:                   /* urb unlinked by us */
 664                 default:                        /* ??? - Play safe */
 665                         urb->status = 0;
 666                         netif_wake_queue(self->netdev);
 667                         done = 1;
 668                         break;
 669                 }
 670         }
 671
 672         /* Check Tx URB */
 673         urb = self->tx_urb;
 674         if (urb->status != 0) {
 675                 struct sk_buff *skb = urb->context;
 676
 677                 IRDA_DEBUG(0, "%s: Tx timed out, urb->status=%d, urb->transfer_flags=0x%04X\n", netdev->name, urb->status, urb->transfer_flags);
 678
 679                 /* Increase error count */
 680                 self->stats.tx_errors++;
 681
 682 #ifdef IU_BUG_KICK_TIMEOUT
 683                 /* Can't be a bad idea to reset the speed ;-) - Jean II */
 684                 if(self->new_speed == -1)
 685                         self->new_speed = self->speed;
 686                 if(self->new_xbofs == -1)
 687                         self->new_xbofs = self->xbofs;
 688                 irda_usb_change_speed_xbofs(self);
 689 #endif /* IU_BUG_KICK_TIMEOUT */
 690
 691                 switch (urb->status) {
 692                 case -EINPROGRESS:
 693                         usb_unlink_urb(urb);
 694                         /* Note : above will  *NOT* call netif_wake_queue()
 695                          * in completion handler, because urb->status will
 696                          * be -ENOENT. We will fix that at the next watchdog,
 697                          * leaving more time to USB to recover...
 698                          * Jean II */
 699                         done = 1;
 700                         break;
 701                 case -ECONNRESET:
 702                 case -ENOENT:                   /* urb unlinked by us */
 703                 default:                        /* ??? - Play safe */
 704                         if(skb != NULL) {
 705                                 dev_kfree_skb_any(skb);
 706                                 urb->context = NULL;
 707                         }
 708                         urb->status = 0;
 709                         netif_wake_queue(self->netdev);
 710                         done = 1;
 711                         break;
 712                 }
 713         }
 714         spin_unlock_irqrestore(&self->lock, flags);
 715
 716         /* Maybe we need a reset */
 717         /* Note : Some drivers seem to use a usb_set_interface() when they
 718          * need to reset the hardware. Hum...
 719          */
 720
 721         /* if(done == 0) */
 722 }
 723
 724 /************************* RECEIVE ROUTINES *************************/
 725 /*
 726  * Receive packets from the USB layer stack and pass them to the IrDA stack.
 727  * Try to work around USB failures...
 728  */
 729
 730 /*
 731  * Note :
 732  * Some of you may have noticed that most dongle have an interrupt in pipe
 733  * that we don't use. Here is the little secret...
 734  * When we hang a Rx URB on the bulk in pipe, it generates some USB traffic
 735  * in every USB frame. This is unnecessary overhead.
 736  * The interrupt in pipe will generate an event every time a packet is
 737  * received. Reading an interrupt pipe adds minimal overhead, but has some
 738  * latency (~1ms).
 739  * If we are connected (speed != 9600), we want to minimise latency, so
 740  * we just always hang the Rx URB and ignore the interrupt.
 741  * If we are not connected (speed == 9600), there is usually no Rx traffic,
 742  * and we want to minimise the USB overhead. In this case we should wait
 743  * on the interrupt pipe and hang the Rx URB only when an interrupt is
 744  * received.
 745  * Jean II
 746  *
 747  * Note : don't read the above as what we are currently doing, but as
 748  * something we could do with KC dongle. Also don't forget that the
 749  * interrupt pipe is not part of the original standard, so this would
 750  * need to be optional...
 751  * Jean II
 752  */
 753
 754 /*------------------------------------------------------------------*/
 755 /*
 756  * Submit a Rx URB to the USB layer to handle reception of a frame
 757  * Mostly called by the completion callback of the previous URB.
 758  *
 759  * Jean II
 760  */
 761 static void irda_usb_submit(struct irda_usb_cb *self, struct sk_buff *skb, struct urb *urb)
 762 {
 763         struct irda_skb_cb *cb;
 764         int ret;
 765
 766         IRDA_DEBUG(2, "%s()\n", __func__);
 767
 768         /* This should never happen */
 769         IRDA_ASSERT(skb != NULL, return;);
 770         IRDA_ASSERT(urb != NULL, return;);
 771
 772         /* Save ourselves in the skb */
 773         cb = (struct irda_skb_cb *) skb->cb;
 774         cb->context = self;
 775
 776         /* Reinitialize URB */
 777         usb_fill_bulk_urb(urb, self->usbdev,
 778                       usb_rcvbulkpipe(self->usbdev, self->bulk_in_ep),
 779                       skb->data, IRDA_SKB_MAX_MTU,
 780                       irda_usb_receive, skb);
 781         urb->status = 0;
 782
 783         /* Can be called from irda_usb_receive (irq handler) -> GFP_ATOMIC */
 784         ret = usb_submit_urb(urb, GFP_ATOMIC);
 785         if (ret) {
 786                 /* If this ever happen, we are in deep s***.
 787                  * Basically, the Rx path will stop... */
 788                 IRDA_WARNING("%s(), Failed to submit Rx URB %d\n",
 789                              __func__, ret);
 790         }
 791 }
 792
 793 /*------------------------------------------------------------------*/
 794 /*
 795  * Function irda_usb_receive(urb)
 796  *
 797  *     Called by the USB subsystem when a frame has been received
 798  *
 799  */
 800 static void irda_usb_receive(struct urb *urb)
 801 {
 802         struct sk_buff *skb = (struct sk_buff *) urb->context;
 803         struct irda_usb_cb *self;
 804         struct irda_skb_cb *cb;
 805         struct sk_buff *newskb;
 806         struct sk_buff *dataskb;
 807         struct urb *next_urb;
 808         unsigned int len, docopy;
 809
 810         IRDA_DEBUG(2, "%s(), len=%d\n", __func__, urb->actual_length);
 811
 812         /* Find ourselves */
 813         cb = (struct irda_skb_cb *) skb->cb;
 814         IRDA_ASSERT(cb != NULL, return;);
 815         self = (struct irda_usb_cb *) cb->context;
 816         IRDA_ASSERT(self != NULL, return;);
 817
 818         /* If the network is closed or the device gone, stop everything */
 819         if ((!self->netopen) || (!self->present)) {
 820                 IRDA_DEBUG(0, "%s(), Network is gone!\n", __func__);
 821                 /* Don't re-submit the URB : will stall the Rx path */
 822                 return;
 823         }
 824
 825         /* Check the status */
 826         if (urb->status != 0) {
 827                 switch (urb->status) {
 828                 case -EILSEQ:
 829                         self->stats.rx_crc_errors++;
 830                         /* Also precursor to a hot-unplug on UHCI. */
 831                         /* Fallthrough... */
 832                 case -ECONNRESET:
 833                         /* Random error, if I remember correctly */
 834                         /* uhci_cleanup_unlink() is going to kill the Rx
 835                          * URB just after we return. No problem, at this
 836                          * point the URB will be idle ;-) - Jean II */
 837                 case -ESHUTDOWN:
 838                         /* That's usually a hot-unplug. Submit will fail... */
 839                 case -ETIME:
 840                         /* Usually precursor to a hot-unplug on OHCI. */
 841                 default:
 842                         self->stats.rx_errors++;
 843                         IRDA_DEBUG(0, "%s(), RX status %d, transfer_flags 0x%04X \n", __func__, urb->status, urb->transfer_flags);
 844                         break;
 845                 }
 846                 /* If we received an error, we don't want to resubmit the
 847                  * Rx URB straight away but to give the USB layer a little
 848                  * bit of breathing room.
 849                  * We are in the USB thread context, therefore there is a
 850                  * danger of recursion (new URB we submit fails, we come
 851                  * back here).
 852                  * With recent USB stack (2.6.15+), I'm seeing that on
 853                  * hot unplug of the dongle...
 854                  * Lowest effective timer is 10ms...
 855                  * Jean II */
 856                 self->rx_defer_timer.function = &irda_usb_rx_defer_expired;
 857                 self->rx_defer_timer.data = (unsigned long) urb;
 858                 mod_timer(&self->rx_defer_timer, jiffies + (10 * HZ / 1000));
 859                 return;
 860         }
 861
 862         /* Check for empty frames */
 863         if (urb->actual_length <= self->header_length) {
 864                 IRDA_WARNING("%s(), empty frame!\n", __func__);
 865                 goto done;
 866         }
 867
 868         /*
 869          * Remember the time we received this frame, so we can
 870          * reduce the min turn time a bit since we will know
 871          * how much time we have used for protocol processing
 872          */
 873         do_gettimeofday(&self->stamp);
 874
 875         /* Check if we need to copy the data to a new skb or not.
 876          * For most frames, we use ZeroCopy and pass the already
 877          * allocated skb up the stack.
 878          * If the frame is small, it is more efficient to copy it
 879          * to save memory (copy will be fast anyway - that's
 880          * called Rx-copy-break). Jean II */
 881         docopy = (urb->actual_length < IRDA_RX_COPY_THRESHOLD);
 882
 883         /* Allocate a new skb */
 884         if (self->capability & IUC_STIR421X)
 885                 newskb = dev_alloc_skb(docopy ? urb->actual_length :
 886                                        IRDA_SKB_MAX_MTU +
 887                                        USB_IRDA_STIR421X_HEADER);
 888         else
 889                 newskb = dev_alloc_skb(docopy ? urb->actual_length :
 890                                        IRDA_SKB_MAX_MTU);
 891
 892         if (!newskb)  {
 893                 self->stats.rx_dropped++;
 894                 /* We could deliver the current skb, but this would stall
 895                  * the Rx path. Better drop the packet... Jean II */
 896                 goto done;
 897         }
 898
 899         /* Make sure IP header get aligned (IrDA header is 5 bytes) */
 900         /* But IrDA-USB header is 1 byte. Jean II */
 901         //skb_reserve(newskb, USB_IRDA_HEADER - 1);
 902
 903         if(docopy) {
 904                 /* Copy packet, so we can recycle the original */
 905                 skb_copy_from_linear_data(skb, newskb->data, urb->actual_length);
 906                 /* Deliver this new skb */
 907                 dataskb = newskb;
 908                 /* And hook the old skb to the URB
 909                  * Note : we don't need to "clean up" the old skb,
 910                  * as we never touched it. Jean II */
 911         } else {
 912                 /* We are using ZeroCopy. Deliver old skb */
 913                 dataskb = skb;
 914                 /* And hook the new skb to the URB */
 915                 skb = newskb;
 916         }
 917
 918         /* Set proper length on skb & remove USB-IrDA header */
 919         skb_put(dataskb, urb->actual_length);
 920         skb_pull(dataskb, self->header_length);
 921
 922         /* Ask the networking layer to queue the packet for the IrDA stack */
 923         dataskb->dev = self->netdev;
 924         skb_reset_mac_header(dataskb);
 925         dataskb->protocol = htons(ETH_P_IRDA);
 926         len = dataskb->len;
 927         netif_rx(dataskb);
 928
 929         /* Keep stats up to date */
 930         self->stats.rx_bytes += len;
 931         self->stats.rx_packets++;
 932
 933 done:
 934         /* Note : at this point, the URB we've just received (urb)
 935          * is still referenced by the USB layer. For example, if we
 936          * have received a -ECONNRESET, uhci_cleanup_unlink() will
 937          * continue to process it (in fact, cleaning it up).
 938          * If we were to submit this URB, disaster would ensue.
 939          * Therefore, we submit our idle URB, and put this URB in our
 940          * idle slot....
 941          * Jean II */
 942         /* Note : with this scheme, we could submit the idle URB before
 943          * processing the Rx URB. I don't think it would buy us anything as
 944          * we are running in the USB thread context. Jean II */
 945         next_urb = self->idle_rx_urb;
 946
 947         /* Recycle Rx URB : Now, the idle URB is the present one */
 948         urb->context = NULL;
 949         self->idle_rx_urb = urb;
 950
 951         /* Submit the idle URB to replace the URB we've just received.
 952          * Do it last to avoid race conditions... Jean II */
 953         irda_usb_submit(self, skb, next_urb);
 954 }
 955
 956 /*------------------------------------------------------------------*/
 957 /*
 958  * In case of errors, we want the USB layer to have time to recover.
 959  * Now, it is time to resubmit ouur Rx URB...
 960  */
 961 static void irda_usb_rx_defer_expired(unsigned long data)
 962 {
 963         struct urb *urb = (struct urb *) data;
 964         struct sk_buff *skb = (struct sk_buff *) urb->context;
 965         struct irda_usb_cb *self;
 966         struct irda_skb_cb *cb;
 967         struct urb *next_urb;
 968
 969         IRDA_DEBUG(2, "%s()\n", __func__);
 970
 971         /* Find ourselves */
 972         cb = (struct irda_skb_cb *) skb->cb;
 973         IRDA_ASSERT(cb != NULL, return;);
 974         self = (struct irda_usb_cb *) cb->context;
 975         IRDA_ASSERT(self != NULL, return;);
 976
 977         /* Same stuff as when Rx is done, see above... */
 978         next_urb = self->idle_rx_urb;
 979         urb->context = NULL;
 980         self->idle_rx_urb = urb;
 981         irda_usb_submit(self, skb, next_urb);
 982 }
 983
 984 /*------------------------------------------------------------------*/
 985 /*
 986  * Callbak from IrDA layer. IrDA wants to know if we have
 987  * started receiving anything.
 988  */
 989 static int irda_usb_is_receiving(struct irda_usb_cb *self)
 990 {
 991         /* Note : because of the way UHCI works, it's almost impossible
 992          * to get this info. The Controller DMA directly to memory and
 993          * signal only when the whole frame is finished. To know if the
 994          * first TD of the URB has been filled or not seems hard work...
 995          *
 996          * The other solution would be to use the "receiving" command
 997          * on the default decriptor with a usb_control_msg(), but that
 998          * would add USB traffic and would return result only in the
 999          * next USB frame (~1ms).
1000          *
1001          * I've been told that current dongles send status info on their
1002          * interrupt endpoint, and that's what the Windows driver uses
1003          * to know this info. Unfortunately, this is not yet in the spec...
1004          *
1005          * Jean II
1006          */
1007
1008         return 0; /* For now */
1009 }
1010
1011 #define STIR421X_PATCH_PRODUCT_VER     "Product Version: "
1012 #define STIR421X_PATCH_STMP_TAG        "STMP"
1013 #define STIR421X_PATCH_CODE_OFFSET     512 /* patch image starts before here */
1014 /* marks end of patch file header (PC DOS text file EOF character) */
1015 #define STIR421X_PATCH_END_OF_HDR_TAG  0x1A
1016 #define STIR421X_PATCH_BLOCK_SIZE      1023
1017
1018 /*
1019  * Function stir421x_fwupload (struct irda_usb_cb *self,
1020  *                             unsigned char *patch,
1021  *                             const unsigned int patch_len)
1022  *
1023  *   Upload firmware code to SigmaTel 421X IRDA-USB dongle
1024  */
1025 static int stir421x_fw_upload(struct irda_usb_cb *self,
1026                              const unsigned char *patch,
1027                              const unsigned int patch_len)
1028 {
1029         int ret = -ENOMEM;
1030         int actual_len = 0;
1031         unsigned int i;
1032         unsigned int block_size = 0;
1033         unsigned char *patch_block;
1034
1035         patch_block = kzalloc(STIR421X_PATCH_BLOCK_SIZE, GFP_KERNEL);
1036         if (patch_block == NULL)
1037                 return -ENOMEM;
1038
1039         /* break up patch into 1023-byte sections */
1040         for (i = 0; i < patch_len; i += block_size) {
1041                 block_size = patch_len - i;
1042
1043                 if (block_size > STIR421X_PATCH_BLOCK_SIZE)
1044                         block_size = STIR421X_PATCH_BLOCK_SIZE;
1045
1046                 /* upload the patch section */
1047                 memcpy(patch_block, patch + i, block_size);
1048
1049                 ret = usb_bulk_msg(self->usbdev,
1050                                    usb_sndbulkpipe(self->usbdev,
1051                                                    self->bulk_out_ep),
1052                                    patch_block, block_size,
1053                                    &actual_len, msecs_to_jiffies(500));
1054                 IRDA_DEBUG(3,"%s(): Bulk send %u bytes, ret=%d\n",
1055                            __func__, actual_len, ret);
1056
1057                 if (ret < 0)
1058                         break;
1059
1060                 mdelay(10);
1061         }
1062
1063         kfree(patch_block);
1064
1065         return ret;
1066  }
1067
1068 /*
1069  * Function stir421x_patch_device(struct irda_usb_cb *self)
1070  *
1071  * Get a firmware code from userspase using hotplug request_firmware() call
1072   */
1073 static int stir421x_patch_device(struct irda_usb_cb *self)
1074 {
1075         unsigned int i;
1076         int ret;
1077         char stir421x_fw_name[11];
1078         const struct firmware *fw;
1079         const unsigned char *fw_version_ptr; /* pointer to version string */
1080         unsigned long fw_version = 0;
1081
1082         /*
1083          * Known firmware patch file names for STIR421x dongles
1084          * are "42101001.sb" or "42101002.sb"
1085          */
1086         sprintf(stir421x_fw_name, "4210%4X.sb",
1087                 self->usbdev->descriptor.bcdDevice);
1088         ret = request_firmware(&fw, stir421x_fw_name, &self->usbdev->dev);
1089         if (ret < 0)
1090                 return ret;
1091
1092         /* We get a patch from userspace */
1093         IRDA_MESSAGE("%s(): Received firmware %s (%zu bytes)\n",
1094                      __func__, stir421x_fw_name, fw->size);
1095
1096         ret = -EINVAL;
1097
1098         /* Get the bcd product version */
1099         if (!memcmp(fw->data, STIR421X_PATCH_PRODUCT_VER,
1100                     sizeof(STIR421X_PATCH_PRODUCT_VER) - 1)) {
1101                 fw_version_ptr = fw->data +
1102                         sizeof(STIR421X_PATCH_PRODUCT_VER) - 1;
1103
1104                 /* Let's check if the product version is dotted */
1105                 if (fw_version_ptr[3] == '.' &&
1106                     fw_version_ptr[7] == '.') {
1107                         unsigned long major, minor, build;
1108                         major = simple_strtoul(fw_version_ptr, NULL, 10);
1109                         minor = simple_strtoul(fw_version_ptr + 4, NULL, 10);
1110                         build = simple_strtoul(fw_version_ptr + 8, NULL, 10);
1111
1112                         fw_version = (major << 12)
1113                                 + (minor << 8)
1114                                 + ((build / 10) << 4)
1115                                 + (build % 10);
1116
1117                         IRDA_DEBUG(3, "%s(): Firmware Product version %ld\n",
1118                                    __func__, fw_version);
1119                 }
1120         }
1121
1122         if (self->usbdev->descriptor.bcdDevice == cpu_to_le16(fw_version)) {
1123                 /*
1124                  * If we're here, we've found a correct patch
1125                  * The actual image starts after the "STMP" keyword
1126                  * so forward to the firmware header tag
1127                  */
1128                 for (i = 0; (fw->data[i] != STIR421X_PATCH_END_OF_HDR_TAG)
1129                              && (i < fw->size); i++) ;
1130                 /* here we check for the out of buffer case */
1131                 if ((STIR421X_PATCH_END_OF_HDR_TAG == fw->data[i])
1132                     && (i < STIR421X_PATCH_CODE_OFFSET)) {
1133                         if (!memcmp(fw->data + i + 1, STIR421X_PATCH_STMP_TAG,
1134                                     sizeof(STIR421X_PATCH_STMP_TAG) - 1)) {
1135
1136                                 /* We can upload the patch to the target */
1137                                 i += sizeof(STIR421X_PATCH_STMP_TAG);
1138                                 ret = stir421x_fw_upload(self, &fw->data[i],
1139                                                          fw->size - i);
1140                         }
1141                 }
1142         }
1143
1144         release_firmware(fw);
1145
1146         return ret;
1147 }
1148
1149
1150 /********************** IRDA DEVICE CALLBACKS **********************/
1151 /*
1152  * Main calls from the IrDA/Network subsystem.
1153  * Mostly registering a new irda-usb device and removing it....
1154  * We only deal with the IrDA side of the business, the USB side will
1155  * be dealt with below...
1156  */
1157
1158
1159 /*------------------------------------------------------------------*/
1160 /*
1161  * Function irda_usb_net_open (dev)
1162  *
1163  *    Network device is taken up. Usually this is done by "ifconfig irda0 up"
1164  *
1165  * Note : don't mess with self->netopen - Jean II
1166  */
1167 static int irda_usb_net_open(struct net_device *netdev)
1168 {
1169         struct irda_usb_cb *self;
1170         unsigned long flags;
1171         char    hwname[16];
1172         int i;
1173
1174         IRDA_DEBUG(1, "%s()\n", __func__);
1175
1176         IRDA_ASSERT(netdev != NULL, return -1;);
1177         self = netdev_priv(netdev);
1178         IRDA_ASSERT(self != NULL, return -1;);
1179
1180         spin_lock_irqsave(&self->lock, flags);
1181         /* Can only open the device if it's there */
1182         if(!self->present) {
1183                 spin_unlock_irqrestore(&self->lock, flags);
1184                 IRDA_WARNING("%s(), device not present!\n", __func__);
1185                 return -1;
1186         }
1187
1188         if(self->needspatch) {
1189                 spin_unlock_irqrestore(&self->lock, flags);
1190                 IRDA_WARNING("%s(), device needs patch\n", __func__) ;
1191                 return -EIO ;
1192         }
1193
1194         /* Initialise default speed and xbofs value
1195          * (IrLAP will change that soon) */
1196         self->speed = -1;
1197         self->xbofs = -1;
1198         self->new_speed = -1;
1199         self->new_xbofs = -1;
1200
1201         /* To do *before* submitting Rx urbs and starting net Tx queue
1202          * Jean II */
1203         self->netopen = 1;
1204         spin_unlock_irqrestore(&self->lock, flags);
1205
1206         /*
1207          * Now that everything should be initialized properly,
1208          * Open new IrLAP layer instance to take care of us...
1209          * Note : will send immediately a speed change...
1210          */
1211         sprintf(hwname, "usb#%d", self->usbdev->devnum);
1212         self->irlap = irlap_open(netdev, &self->qos, hwname);
1213         IRDA_ASSERT(self->irlap != NULL, return -1;);
1214
1215         /* Allow IrLAP to send data to us */
1216         netif_start_queue(netdev);
1217
1218         /* We submit all the Rx URB except for one that we keep idle.
1219          * Need to be initialised before submitting other USBs, because
1220          * in some cases as soon as we submit the URBs the USB layer
1221          * will trigger a dummy receive - Jean II */
1222         self->idle_rx_urb = self->rx_urb[IU_MAX_ACTIVE_RX_URBS];
1223         self->idle_rx_urb->context = NULL;
1224
1225         /* Now that we can pass data to IrLAP, allow the USB layer
1226          * to send us some data... */
1227         for (i = 0; i < IU_MAX_ACTIVE_RX_URBS; i++) {
1228                 struct sk_buff *skb = dev_alloc_skb(IRDA_SKB_MAX_MTU);
1229                 if (!skb) {
1230                         /* If this ever happen, we are in deep s***.
1231                          * Basically, we can't start the Rx path... */
1232                         IRDA_WARNING("%s(), Failed to allocate Rx skb\n",
1233                                      __func__);
1234                         return -1;
1235                 }
1236                 //skb_reserve(newskb, USB_IRDA_HEADER - 1);
1237                 irda_usb_submit(self, skb, self->rx_urb[i]);
1238         }
1239
1240         /* Ready to play !!! */
1241         return 0;
1242 }
1243
1244 /*------------------------------------------------------------------*/
1245 /*
1246  * Function irda_usb_net_close (self)
1247  *
1248  *    Network device is taken down. Usually this is done by
1249  *    "ifconfig irda0 down"
1250  */
1251 static int irda_usb_net_close(struct net_device *netdev)
1252 {
1253         struct irda_usb_cb *self;
1254         int     i;
1255
1256         IRDA_DEBUG(1, "%s()\n", __func__);
1257
1258         IRDA_ASSERT(netdev != NULL, return -1;);
1259         self = netdev_priv(netdev);
1260         IRDA_ASSERT(self != NULL, return -1;);
1261
1262         /* Clear this flag *before* unlinking the urbs and *before*
1263          * stopping the network Tx queue - Jean II */
1264         self->netopen = 0;
1265
1266         /* Stop network Tx queue */
1267         netif_stop_queue(netdev);
1268
1269         /* Kill defered Rx URB */
1270         del_timer(&self->rx_defer_timer);
1271
1272         /* Deallocate all the Rx path buffers (URBs and skb) */
1273         for (i = 0; i < self->max_rx_urb; i++) {
1274                 struct urb *urb = self->rx_urb[i];
1275                 struct sk_buff *skb = (struct sk_buff *) urb->context;
1276                 /* Cancel the receive command */
1277                 usb_kill_urb(urb);
1278                 /* The skb is ours, free it */
1279                 if(skb) {
1280                         dev_kfree_skb(skb);
1281                         urb->context = NULL;
1282                 }
1283         }
1284         /* Cancel Tx and speed URB - need to be synchronous to avoid races */
1285         usb_kill_urb(self->tx_urb);
1286         usb_kill_urb(self->speed_urb);
1287
1288         /* Stop and remove instance of IrLAP */
1289         if (self->irlap)
1290                 irlap_close(self->irlap);
1291         self->irlap = NULL;
1292
1293         return 0;
1294 }
1295
1296 /*------------------------------------------------------------------*/
1297 /*
1298  * IOCTLs : Extra out-of-band network commands...
1299  */
1300 static int irda_usb_net_ioctl(struct net_device *dev, struct ifreq *rq, int cmd)
1301 {
1302         unsigned long flags;
1303         struct if_irda_req *irq = (struct if_irda_req *) rq;
1304         struct irda_usb_cb *self;
1305         int ret = 0;
1306
1307         IRDA_ASSERT(dev != NULL, return -1;);
1308         self = netdev_priv(dev);
1309         IRDA_ASSERT(self != NULL, return -1;);
1310
1311         IRDA_DEBUG(2, "%s(), %s, (cmd=0x%X)\n", __func__, dev->name, cmd);
1312
1313         switch (cmd) {
1314         case SIOCSBANDWIDTH: /* Set bandwidth */
1315                 if (!capable(CAP_NET_ADMIN))
1316                         return -EPERM;
1317                 /* Protect us from USB callbacks, net watchdog and else. */
1318                 spin_lock_irqsave(&self->lock, flags);
1319                 /* Check if the device is still there */
1320                 if(self->present) {
1321                         /* Set the desired speed */
1322                         self->new_speed = irq->ifr_baudrate;
1323                         irda_usb_change_speed_xbofs(self);
1324                 }
1325                 spin_unlock_irqrestore(&self->lock, flags);
1326                 break;
1327         case SIOCSMEDIABUSY: /* Set media busy */
1328                 if (!capable(CAP_NET_ADMIN))
1329                         return -EPERM;
1330                 /* Check if the IrDA stack is still there */
1331                 if(self->netopen)
1332                         irda_device_set_media_busy(self->netdev, TRUE);
1333                 break;
1334         case SIOCGRECEIVING: /* Check if we are receiving right now */
1335                 irq->ifr_receiving = irda_usb_is_receiving(self);
1336                 break;
1337         default:
1338                 ret = -EOPNOTSUPP;
1339         }
1340
1341         return ret;
1342 }
1343
1344 /*------------------------------------------------------------------*/
1345 /*
1346  * Get device stats (for /proc/net/dev and ifconfig)
1347  */
1348 static struct net_device_stats *irda_usb_net_get_stats(struct net_device *dev)
1349 {
1350         struct irda_usb_cb *self = netdev_priv(dev);
1351         return &self->stats;
1352 }
1353
1354 /********************* IRDA CONFIG SUBROUTINES *********************/
1355 /*
1356  * Various subroutines dealing with IrDA and network stuff we use to
1357  * configure and initialise each irda-usb instance.
1358  * These functions are used below in the main calls of the driver...
1359  */
1360
1361 /*------------------------------------------------------------------*/
1362 /*
1363  * Set proper values in the IrDA QOS structure
1364  */
1365 static inline void irda_usb_init_qos(struct irda_usb_cb *self)
1366 {
1367         struct irda_class_desc *desc;
1368
1369         IRDA_DEBUG(3, "%s()\n", __func__);
1370
1371         desc = self->irda_desc;
1372
1373         /* Initialize QoS for this device */
1374         irda_init_max_qos_capabilies(&self->qos);
1375
1376         /* See spec section 7.2 for meaning.
1377          * Values are little endian (as most USB stuff), the IrDA stack
1378          * use it in native order (see parameters.c). - Jean II */
1379         self->qos.baud_rate.bits       = le16_to_cpu(desc->wBaudRate);
1380         self->qos.min_turn_time.bits   = desc->bmMinTurnaroundTime;
1381         self->qos.additional_bofs.bits = desc->bmAdditionalBOFs;
1382         self->qos.window_size.bits     = desc->bmWindowSize;
1383         self->qos.data_size.bits       = desc->bmDataSize;
1384
1385         IRDA_DEBUG(0, "%s(), dongle says speed=0x%X, size=0x%X, window=0x%X, bofs=0x%X, turn=0x%X\n",
1386                 __func__, self->qos.baud_rate.bits, self->qos.data_size.bits, self->qos.window_size.bits, self->qos.additional_bofs.bits, self->qos.min_turn_time.bits);
1387
1388         /* Don't always trust what the dongle tell us */
1389         if(self->capability & IUC_SIR_ONLY)
1390                 self->qos.baud_rate.bits        &= 0x00ff;
1391         if(self->capability & IUC_SMALL_PKT)
1392                 self->qos.data_size.bits         = 0x07;
1393         if(self->capability & IUC_NO_WINDOW)
1394                 self->qos.window_size.bits       = 0x01;
1395         if(self->capability & IUC_MAX_WINDOW)
1396                 self->qos.window_size.bits       = 0x7f;
1397         if(self->capability & IUC_MAX_XBOFS)
1398                 self->qos.additional_bofs.bits   = 0x01;
1399
1400 #if 1
1401         /* Module parameter can override the rx window size */
1402         if (qos_mtt_bits)
1403                 self->qos.min_turn_time.bits = qos_mtt_bits;
1404 #endif
1405         /*
1406          * Note : most of those values apply only for the receive path,
1407          * the transmit path will be set differently - Jean II
1408          */
1409         irda_qos_bits_to_value(&self->qos);
1410 }
1411
1412 /*------------------------------------------------------------------*/
1413 /*
1414  * Initialise the network side of the irda-usb instance
1415  * Called when a new USB instance is registered in irda_usb_probe()
1416  */
1417 static inline int irda_usb_open(struct irda_usb_cb *self)
1418 {
1419         struct net_device *netdev = self->netdev;
1420
1421         IRDA_DEBUG(1, "%s()\n", __func__);
1422
1423         irda_usb_init_qos(self);
1424
1425         /* Override the network functions we need to use */
1426         netdev->hard_start_xmit = irda_usb_hard_xmit;
1427         netdev->tx_timeout      = irda_usb_net_timeout;
1428         netdev->watchdog_timeo  = 250*HZ/1000;  /* 250 ms > USB timeout */
1429         netdev->open            = irda_usb_net_open;
1430         netdev->stop            = irda_usb_net_close;
1431         netdev->get_stats       = irda_usb_net_get_stats;
1432         netdev->do_ioctl        = irda_usb_net_ioctl;
1433
1434         return register_netdev(netdev);
1435 }
1436
1437 /*------------------------------------------------------------------*/
1438 /*
1439  * Cleanup the network side of the irda-usb instance
1440  * Called when a USB instance is removed in irda_usb_disconnect()
1441  */
1442 static inline void irda_usb_close(struct irda_usb_cb *self)
1443 {
1444         IRDA_DEBUG(1, "%s()\n", __func__);
1445
1446         /* Remove netdevice */
1447         unregister_netdev(self->netdev);
1448
1449         /* Remove the speed buffer */
1450         kfree(self->speed_buff);
1451         self->speed_buff = NULL;
1452
1453         kfree(self->tx_buff);
1454         self->tx_buff = NULL;
1455 }
1456
1457 /********************** USB CONFIG SUBROUTINES **********************/
1458 /*
1459  * Various subroutines dealing with USB stuff we use to configure and
1460  * initialise each irda-usb instance.
1461  * These functions are used below in the main calls of the driver...
1462  */
1463
1464 /*------------------------------------------------------------------*/
1465 /*
1466  * Function irda_usb_parse_endpoints(dev, ifnum)
1467  *
1468  *    Parse the various endpoints and find the one we need.
1469  *
1470  * The endpoint are the pipes used to communicate with the USB device.
1471  * The spec defines 2 endpoints of type bulk transfer, one in, and one out.
1472  * These are used to pass frames back and forth with the dongle.
1473  * Most dongle have also an interrupt endpoint, that will be probably
1474  * documented in the next spec...
1475  */
1476 static inline int irda_usb_parse_endpoints(struct irda_usb_cb *self, struct usb_host_endpoint *endpoint, int ennum)
1477 {
1478         int i;          /* Endpoint index in table */
1479
1480         /* Init : no endpoints */
1481         self->bulk_in_ep = 0;
1482         self->bulk_out_ep = 0;
1483         self->bulk_int_ep = 0;
1484
1485         /* Let's look at all those endpoints */
1486         for(i = 0; i < ennum; i++) {
1487                 /* All those variables will get optimised by the compiler,
1488                  * so let's aim for clarity... - Jean II */
1489                 __u8 ep;        /* Endpoint address */
1490                 __u8 dir;       /* Endpoint direction */
1491                 __u8 attr;      /* Endpoint attribute */
1492                 __u16 psize;    /* Endpoint max packet size in bytes */
1493
1494                 /* Get endpoint address, direction and attribute */
1495                 ep = endpoint[i].desc.bEndpointAddress & USB_ENDPOINT_NUMBER_MASK;
1496                 dir = endpoint[i].desc.bEndpointAddress & USB_ENDPOINT_DIR_MASK;
1497                 attr = endpoint[i].desc.bmAttributes;
1498                 psize = le16_to_cpu(endpoint[i].desc.wMaxPacketSize);
1499
1500                 /* Is it a bulk endpoint ??? */
1501                 if(attr == USB_ENDPOINT_XFER_BULK) {
1502                         /* We need to find an IN and an OUT */
1503                         if(dir == USB_DIR_IN) {
1504                                 /* This is our Rx endpoint */
1505                                 self->bulk_in_ep = ep;
1506                         } else {
1507                                 /* This is our Tx endpoint */
1508                                 self->bulk_out_ep = ep;
1509                                 self->bulk_out_mtu = psize;
1510                         }
1511                 } else {
1512                         if((attr == USB_ENDPOINT_XFER_INT) &&
1513                            (dir == USB_DIR_IN)) {
1514                                 /* This is our interrupt endpoint */
1515                                 self->bulk_int_ep = ep;
1516                         } else {
1517                                 IRDA_ERROR("%s(), Unrecognised endpoint %02X.\n", __func__, ep);
1518                         }
1519                 }
1520         }
1521
1522         IRDA_DEBUG(0, "%s(), And our endpoints are : in=%02X, out=%02X (%d), int=%02X\n",
1523                 __func__, self->bulk_in_ep, self->bulk_out_ep, self->bulk_out_mtu, self->bulk_int_ep);
1524
1525         return((self->bulk_in_ep != 0) && (self->bulk_out_ep != 0));
1526 }
1527
1528 #ifdef IU_DUMP_CLASS_DESC
1529 /*------------------------------------------------------------------*/
1530 /*
1531  * Function usb_irda_dump_class_desc(desc)
1532  *
1533  *    Prints out the contents of the IrDA class descriptor
1534  *
1535  */
1536 static inline void irda_usb_dump_class_desc(struct irda_class_desc *desc)
1537 {
1538         /* Values are little endian */
1539         printk("bLength=%x\n", desc->bLength);
1540         printk("bDescriptorType=%x\n", desc->bDescriptorType);
1541         printk("bcdSpecRevision=%x\n", le16_to_cpu(desc->bcdSpecRevision));
1542         printk("bmDataSize=%x\n", desc->bmDataSize);
1543         printk("bmWindowSize=%x\n", desc->bmWindowSize);
1544         printk("bmMinTurnaroundTime=%d\n", desc->bmMinTurnaroundTime);
1545         printk("wBaudRate=%x\n", le16_to_cpu(desc->wBaudRate));
1546         printk("bmAdditionalBOFs=%x\n", desc->bmAdditionalBOFs);
1547         printk("bIrdaRateSniff=%x\n", desc->bIrdaRateSniff);
1548         printk("bMaxUnicastList=%x\n", desc->bMaxUnicastList);
1549 }
1550 #endif /* IU_DUMP_CLASS_DESC */
1551
1552 /*------------------------------------------------------------------*/
1553 /*
1554  * Function irda_usb_find_class_desc(intf)
1555  *
1556  *    Returns instance of IrDA class descriptor, or NULL if not found
1557  *
1558  * The class descriptor is some extra info that IrDA USB devices will
1559  * offer to us, describing their IrDA characteristics. We will use that in
1560  * irda_usb_init_qos()
1561  */
1562 static inline struct irda_class_desc *irda_usb_find_class_desc(struct usb_interface *intf)
1563 {
1564         struct usb_device *dev = interface_to_usbdev (intf);
1565         struct irda_class_desc *desc;
1566         int ret;
1567
1568         desc = kzalloc(sizeof(*desc), GFP_KERNEL);
1569         if (!desc)
1570                 return NULL;
1571
1572         /* USB-IrDA class spec 1.0:
1573          *      6.1.3: Standard "Get Descriptor" Device Request is not
1574          *             appropriate to retrieve class-specific descriptor
1575          *      6.2.5: Class Specific "Get Class Descriptor" Interface Request
1576          *             is mandatory and returns the USB-IrDA class descriptor
1577          */
1578
1579         ret = usb_control_msg(dev, usb_rcvctrlpipe(dev,0),
1580                 IU_REQ_GET_CLASS_DESC,
1581                 USB_DIR_IN | USB_TYPE_CLASS | USB_RECIP_INTERFACE,
1582                 0, intf->altsetting->desc.bInterfaceNumber, desc,
1583                 sizeof(*desc), 500);
1584
1585         IRDA_DEBUG(1, "%s(), ret=%d\n", __func__, ret);
1586         if (ret < sizeof(*desc)) {
1587                 IRDA_WARNING("usb-irda: class_descriptor read %s (%d)\n",
1588                              (ret<0) ? "failed" : "too short", ret);
1589         }
1590         else if (desc->bDescriptorType != USB_DT_IRDA) {
1591                 IRDA_WARNING("usb-irda: bad class_descriptor type\n");
1592         }
1593         else {
1594 #ifdef IU_DUMP_CLASS_DESC
1595                 irda_usb_dump_class_desc(desc);
1596 #endif  /* IU_DUMP_CLASS_DESC */
1597
1598                 return desc;
1599         }
1600         kfree(desc);
1601         return NULL;
1602 }
1603
1604 /*********************** USB DEVICE CALLBACKS ***********************/
1605 /*
1606  * Main calls from the USB subsystem.
1607  * Mostly registering a new irda-usb device and removing it....
1608  */
1609
1610 /*------------------------------------------------------------------*/
1611 /*
1612  * This routine is called by the USB subsystem for each new device
1613  * in the system. We need to check if the device is ours, and in
1614  * this case start handling it.
1615  * The USB layer protect us from reentrancy (via BKL), so we don't need
1616  * to spinlock in there... Jean II
1617  */
1618 static int irda_usb_probe(struct usb_interface *intf,
1619                           const struct usb_device_id *id)
1620 {
1621         struct net_device *net;
1622         struct usb_device *dev = interface_to_usbdev(intf);
1623         struct irda_usb_cb *self;
1624         struct usb_host_interface *interface;
1625         struct irda_class_desc *irda_desc;
1626         int ret = -ENOMEM;
1627         int i;          /* Driver instance index / Rx URB index */
1628
1629         /* Note : the probe make sure to call us only for devices that
1630          * matches the list of dongle (top of the file). So, we
1631          * don't need to check if the dongle is really ours.
1632          * Jean II */
1633
1634         IRDA_MESSAGE("IRDA-USB found at address %d, Vendor: %x, Product: %x\n",
1635                      dev->devnum, le16_to_cpu(dev->descriptor.idVendor),
1636                      le16_to_cpu(dev->descriptor.idProduct));
1637
1638         net = alloc_irdadev(sizeof(*self));
1639         if (!net)
1640                 goto err_out;
1641
1642         SET_NETDEV_DEV(net, &intf->dev);
1643         self = netdev_priv(net);
1644         self->netdev = net;
1645         spin_lock_init(&self->lock);
1646         init_timer(&self->rx_defer_timer);
1647
1648         self->capability = id->driver_info;
1649         self->needspatch = ((self->capability & IUC_STIR421X) != 0);
1650
1651         /* Create all of the needed urbs */
1652         if (self->capability & IUC_STIR421X) {
1653                 self->max_rx_urb = IU_SIGMATEL_MAX_RX_URBS;
1654                 self->header_length = USB_IRDA_STIR421X_HEADER;
1655         } else {
1656                 self->max_rx_urb = IU_MAX_RX_URBS;
1657                 self->header_length = USB_IRDA_HEADER;
1658         }
1659
1660         self->rx_urb = kcalloc(self->max_rx_urb, sizeof(struct urb *),
1661                                 GFP_KERNEL);
1662
1663         for (i = 0; i < self->max_rx_urb; i++) {
1664                 self->rx_urb[i] = usb_alloc_urb(0, GFP_KERNEL);
1665                 if (!self->rx_urb[i]) {
1666                         goto err_out_1;
1667                 }
1668         }
1669         self->tx_urb = usb_alloc_urb(0, GFP_KERNEL);
1670         if (!self->tx_urb) {
1671                 goto err_out_1;
1672         }
1673         self->speed_urb = usb_alloc_urb(0, GFP_KERNEL);
1674         if (!self->speed_urb) {
1675                 goto err_out_2;
1676         }
1677
1678         /* Is this really necessary? (no, except maybe for broken devices) */
1679         if (usb_reset_configuration (dev) < 0) {
1680                 err("reset_configuration failed");
1681                 ret = -EIO;
1682                 goto err_out_3;
1683         }
1684
1685         /* Is this really necessary? */
1686         /* Note : some driver do hardcode the interface number, some others
1687          * specify an alternate, but very few driver do like this.
1688          * Jean II */
1689         ret = usb_set_interface(dev, intf->altsetting->desc.bInterfaceNumber, 0);
1690         IRDA_DEBUG(1, "usb-irda: set interface %d result %d\n", intf->altsetting->desc.bInterfaceNumber, ret);
1691         switch (ret) {
1692                 case 0:
1693                         break;
1694                 case -EPIPE:            /* -EPIPE = -32 */
1695                         /* Martin Diehl says if we get a -EPIPE we should
1696                          * be fine and we don't need to do a usb_clear_halt().
1697                          * - Jean II */
1698                         IRDA_DEBUG(0, "%s(), Received -EPIPE, ignoring...\n", __func__);
1699                         break;
1700                 default:
1701                         IRDA_DEBUG(0, "%s(), Unknown error %d\n", __func__, ret);
1702                         ret = -EIO;
1703                         goto err_out_3;
1704         }
1705
1706         /* Find our endpoints */
1707         interface = intf->cur_altsetting;
1708         if(!irda_usb_parse_endpoints(self, interface->endpoint,
1709                                      interface->desc.bNumEndpoints)) {
1710                 IRDA_ERROR("%s(), Bogus endpoints...\n", __func__);
1711                 ret = -EIO;
1712                 goto err_out_3;
1713         }
1714
1715         self->usbdev = dev;
1716
1717         /* Find IrDA class descriptor */
1718         irda_desc = irda_usb_find_class_desc(intf);
1719         ret = -ENODEV;
1720         if (!irda_desc)
1721                 goto err_out_3;
1722
1723         if (self->needspatch) {
1724                 ret = usb_control_msg (self->usbdev, usb_sndctrlpipe (self->usbdev, 0),
1725                                        0x02, 0x40, 0, 0, NULL, 0, 500);
1726                 if (ret < 0) {
1727                         IRDA_DEBUG (0, "usb_control_msg failed %d\n", ret);
1728                         goto err_out_3;
1729                 } else {
1730                         mdelay(10);
1731                 }
1732         }
1733
1734         self->irda_desc =  irda_desc;
1735         self->present = 1;
1736         self->netopen = 0;
1737         self->usbintf = intf;
1738
1739         /* Allocate the buffer for speed changes */
1740         /* Don't change this buffer size and allocation without doing
1741          * some heavy and complete testing. Don't ask why :-(
1742          * Jean II */
1743         self->speed_buff = kzalloc(IRDA_USB_SPEED_MTU, GFP_KERNEL);
1744         if (!self->speed_buff)
1745                 goto err_out_3;
1746
1747         self->tx_buff = kzalloc(IRDA_SKB_MAX_MTU + self->header_length,
1748                                 GFP_KERNEL);
1749         if (!self->tx_buff)
1750                 goto err_out_4;
1751
1752         ret = irda_usb_open(self);
1753         if (ret)
1754                 goto err_out_5;
1755
1756         IRDA_MESSAGE("IrDA: Registered device %s\n", net->name);
1757         usb_set_intfdata(intf, self);
1758
1759         if (self->needspatch) {
1760                 /* Now we fetch and upload the firmware patch */
1761                 ret = stir421x_patch_device(self);
1762                 self->needspatch = (ret < 0);
1763                 if (self->needspatch) {
1764                         IRDA_ERROR("STIR421X: Couldn't upload patch\n");
1765                         goto err_out_6;
1766                 }
1767
1768                 /* replace IrDA class descriptor with what patched device is now reporting */
1769                 irda_desc = irda_usb_find_class_desc (self->usbintf);
1770                 if (!irda_desc) {
1771                         ret = -ENODEV;
1772                         goto err_out_6;
1773                 }
1774                 kfree(self->irda_desc);
1775                 self->irda_desc = irda_desc;
1776                 irda_usb_init_qos(self);
1777         }
1778
1779         return 0;
1780 err_out_6:
1781         unregister_netdev(self->netdev);
1782 err_out_5:
1783         kfree(self->tx_buff);
1784 err_out_4:
1785         kfree(self->speed_buff);
1786 err_out_3:
1787         /* Free all urbs that we may have created */
1788         usb_free_urb(self->speed_urb);
1789 err_out_2:
1790         usb_free_urb(self->tx_urb);
1791 err_out_1:
1792         for (i = 0; i < self->max_rx_urb; i++)
1793                 usb_free_urb(self->rx_urb[i]);
1794         free_netdev(net);
1795 err_out:
1796         return ret;
1797 }
1798
1799 /*------------------------------------------------------------------*/
1800 /*
1801  * The current irda-usb device is removed, the USB layer tell us
1802  * to shut it down...
1803  * One of the constraints is that when we exit this function,
1804  * we cannot use the usb_device no more. Gone. Destroyed. kfree().
1805  * Most other subsystem allow you to destroy the instance at a time
1806  * when it's convenient to you, to postpone it to a later date, but
1807  * not the USB subsystem.
1808  * So, we must make bloody sure that everything gets deactivated.
1809  * Jean II
1810  */
1811 static void irda_usb_disconnect(struct usb_interface *intf)
1812 {
1813         unsigned long flags;
1814         struct irda_usb_cb *self = usb_get_intfdata(intf);
1815         int i;
1816
1817         IRDA_DEBUG(1, "%s()\n", __func__);
1818
1819         usb_set_intfdata(intf, NULL);
1820         if (!self)
1821                 return;
1822
1823         /* Make sure that the Tx path is not executing. - Jean II */
1824         spin_lock_irqsave(&self->lock, flags);
1825
1826         /* Oups ! We are not there any more.
1827          * This will stop/desactivate the Tx path. - Jean II */
1828         self->present = 0;
1829
1830         /* Kill defered Rx URB */
1831         del_timer(&self->rx_defer_timer);
1832
1833         /* We need to have irq enabled to unlink the URBs. That's OK,
1834          * at this point the Tx path is gone - Jean II */
1835         spin_unlock_irqrestore(&self->lock, flags);
1836
1837         /* Hum... Check if networking is still active (avoid races) */
1838         if((self->netopen) || (self->irlap)) {
1839                 /* Accept no more transmissions */
1840                 /*netif_device_detach(self->netdev);*/
1841                 netif_stop_queue(self->netdev);
1842                 /* Stop all the receive URBs. Must be synchronous. */
1843                 for (i = 0; i < self->max_rx_urb; i++)
1844                         usb_kill_urb(self->rx_urb[i]);
1845                 /* Cancel Tx and speed URB.
1846                  * Make sure it's synchronous to avoid races. */
1847                 usb_kill_urb(self->tx_urb);
1848                 usb_kill_urb(self->speed_urb);
1849         }
1850
1851         /* Cleanup the device stuff */
1852         irda_usb_close(self);
1853         /* No longer attached to USB bus */
1854         self->usbdev = NULL;
1855         self->usbintf = NULL;
1856
1857         /* Clean up our urbs */
1858         for (i = 0; i < self->max_rx_urb; i++)
1859                 usb_free_urb(self->rx_urb[i]);
1860         kfree(self->rx_urb);
1861         /* Clean up Tx and speed URB */
1862         usb_free_urb(self->tx_urb);
1863         usb_free_urb(self->speed_urb);
1864
1865         /* Free self and network device */
1866         free_netdev(self->netdev);
1867         IRDA_DEBUG(0, "%s(), USB IrDA Disconnected\n", __func__);
1868 }
1869
1870 /*------------------------------------------------------------------*/
1871 /*
1872  * USB device callbacks
1873  */
1874 static struct usb_driver irda_driver = {
1875         .name           = "irda-usb",
1876         .probe          = irda_usb_probe,
1877         .disconnect     = irda_usb_disconnect,
1878         .id_table       = dongles,
1879 };
1880
1881 /************************* MODULE CALLBACKS *************************/
1882 /*
1883  * Deal with module insertion/removal
1884  * Mostly tell USB about our existence
1885  */
1886
1887 /*------------------------------------------------------------------*/
1888 /*
1889  * Module insertion
1890  */
1891 static int __init usb_irda_init(void)
1892 {
1893         int     ret;
1894
1895         ret = usb_register(&irda_driver);
1896         if (ret < 0)
1897                 return ret;
1898
1899         IRDA_MESSAGE("USB IrDA support registered\n");
1900         return 0;
1901 }
1902 module_init(usb_irda_init);
1903
1904 /*------------------------------------------------------------------*/
1905 /*
1906  * Module removal
1907  */
1908 static void __exit usb_irda_cleanup(void)
1909 {
1910         /* Deregister the driver and remove all pending instances */
1911         usb_deregister(&irda_driver);
1912 }
1913 module_exit(usb_irda_cleanup);
1914
1915 /*------------------------------------------------------------------*/
1916 /*
1917  * Module parameters
1918  */
1919 module_param(qos_mtt_bits, int, 0);
1920 MODULE_PARM_DESC(qos_mtt_bits, "Minimum Turn Time");
1921 MODULE_AUTHOR("Roman Weissgaerber <weissg@vienna.at>, Dag Brattli <dag@brattli.net>, Jean Tourrilhes <jt@hpl.hp.com> and Nick Fedchik <nick@fedchik.org.ua>");
1922 MODULE_DESCRIPTION("IrDA-USB Dongle Driver");
1923 MODULE_LICENSE("GPL");