Merge branch 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ieee13...
[linux-2.6] / drivers / net / defxx.c
1 /*
2  * File Name:
3  *   defxx.c
4  *
5  * Copyright Information:
6  *   Copyright Digital Equipment Corporation 1996.
7  *
8  *   This software may be used and distributed according to the terms of
9  *   the GNU General Public License, incorporated herein by reference.
10  *
11  * Abstract:
12  *   A Linux device driver supporting the Digital Equipment Corporation
13  *   FDDI EISA and PCI controller families.  Supported adapters include:
14  *
15  *              DEC FDDIcontroller/EISA (DEFEA)
16  *              DEC FDDIcontroller/PCI  (DEFPA)
17  *
18  * The original author:
19  *   LVS        Lawrence V. Stefani <lstefani@yahoo.com>
20  *
21  * Maintainers:
22  *   macro      Maciej W. Rozycki <macro@linux-mips.org>
23  *
24  * Credits:
25  *   I'd like to thank Patricia Cross for helping me get started with
26  *   Linux, David Davies for a lot of help upgrading and configuring
27  *   my development system and for answering many OS and driver
28  *   development questions, and Alan Cox for recommendations and
29  *   integration help on getting FDDI support into Linux.  LVS
30  *
31  * Driver Architecture:
32  *   The driver architecture is largely based on previous driver work
33  *   for other operating systems.  The upper edge interface and
34  *   functions were largely taken from existing Linux device drivers
35  *   such as David Davies' DE4X5.C driver and Donald Becker's TULIP.C
36  *   driver.
37  *
38  *   Adapter Probe -
39  *              The driver scans for supported EISA adapters by reading the
40  *              SLOT ID register for each EISA slot and making a match
41  *              against the expected value.
42  *
43  *   Bus-Specific Initialization -
44  *              This driver currently supports both EISA and PCI controller
45  *              families.  While the custom DMA chip and FDDI logic is similar
46  *              or identical, the bus logic is very different.  After
47  *              initialization, the     only bus-specific differences is in how the
48  *              driver enables and disables interrupts.  Other than that, the
49  *              run-time critical code behaves the same on both families.
50  *              It's important to note that both adapter families are configured
51  *              to I/O map, rather than memory map, the adapter registers.
52  *
53  *   Driver Open/Close -
54  *              In the driver open routine, the driver ISR (interrupt service
55  *              routine) is registered and the adapter is brought to an
56  *              operational state.  In the driver close routine, the opposite
57  *              occurs; the driver ISR is deregistered and the adapter is
58  *              brought to a safe, but closed state.  Users may use consecutive
59  *              commands to bring the adapter up and down as in the following
60  *              example:
61  *                                      ifconfig fddi0 up
62  *                                      ifconfig fddi0 down
63  *                                      ifconfig fddi0 up
64  *
65  *   Driver Shutdown -
66  *              Apparently, there is no shutdown or halt routine support under
67  *              Linux.  This routine would be called during "reboot" or
68  *              "shutdown" to allow the driver to place the adapter in a safe
69  *              state before a warm reboot occurs.  To be really safe, the user
70  *              should close the adapter before shutdown (eg. ifconfig fddi0 down)
71  *              to ensure that the adapter DMA engine is taken off-line.  However,
72  *              the current driver code anticipates this problem and always issues
73  *              a soft reset of the adapter     at the beginning of driver initialization.
74  *              A future driver enhancement in this area may occur in 2.1.X where
75  *              Alan indicated that a shutdown handler may be implemented.
76  *
77  *   Interrupt Service Routine -
78  *              The driver supports shared interrupts, so the ISR is registered for
79  *              each board with the appropriate flag and the pointer to that board's
80  *              device structure.  This provides the context during interrupt
81  *              processing to support shared interrupts and multiple boards.
82  *
83  *              Interrupt enabling/disabling can occur at many levels.  At the host
84  *              end, you can disable system interrupts, or disable interrupts at the
85  *              PIC (on Intel systems).  Across the bus, both EISA and PCI adapters
86  *              have a bus-logic chip interrupt enable/disable as well as a DMA
87  *              controller interrupt enable/disable.
88  *
89  *              The driver currently enables and disables adapter interrupts at the
90  *              bus-logic chip and assumes that Linux will take care of clearing or
91  *              acknowledging any host-based interrupt chips.
92  *
93  *   Control Functions -
94  *              Control functions are those used to support functions such as adding
95  *              or deleting multicast addresses, enabling or disabling packet
96  *              reception filters, or other custom/proprietary commands.  Presently,
97  *              the driver supports the "get statistics", "set multicast list", and
98  *              "set mac address" functions defined by Linux.  A list of possible
99  *              enhancements include:
100  *
101  *                              - Custom ioctl interface for executing port interface commands
102  *                              - Custom ioctl interface for adding unicast addresses to
103  *                                adapter CAM (to support bridge functions).
104  *                              - Custom ioctl interface for supporting firmware upgrades.
105  *
106  *   Hardware (port interface) Support Routines -
107  *              The driver function names that start with "dfx_hw_" represent
108  *              low-level port interface routines that are called frequently.  They
109  *              include issuing a DMA or port control command to the adapter,
110  *              resetting the adapter, or reading the adapter state.  Since the
111  *              driver initialization and run-time code must make calls into the
112  *              port interface, these routines were written to be as generic and
113  *              usable as possible.
114  *
115  *   Receive Path -
116  *              The adapter DMA engine supports a 256 entry receive descriptor block
117  *              of which up to 255 entries can be used at any given time.  The
118  *              architecture is a standard producer, consumer, completion model in
119  *              which the driver "produces" receive buffers to the adapter, the
120  *              adapter "consumes" the receive buffers by DMAing incoming packet data,
121  *              and the driver "completes" the receive buffers by servicing the
122  *              incoming packet, then "produces" a new buffer and starts the cycle
123  *              again.  Receive buffers can be fragmented in up to 16 fragments
124  *              (descriptor     entries).  For simplicity, this driver posts
125  *              single-fragment receive buffers of 4608 bytes, then allocates a
126  *              sk_buff, copies the data, then reposts the buffer.  To reduce CPU
127  *              utilization, a better approach would be to pass up the receive
128  *              buffer (no extra copy) then allocate and post a replacement buffer.
129  *              This is a performance enhancement that should be looked into at
130  *              some point.
131  *
132  *   Transmit Path -
133  *              Like the receive path, the adapter DMA engine supports a 256 entry
134  *              transmit descriptor block of which up to 255 entries can be used at
135  *              any     given time.  Transmit buffers can be fragmented in up to 255
136  *              fragments (descriptor entries).  This driver always posts one
137  *              fragment per transmit packet request.
138  *
139  *              The fragment contains the entire packet from FC to end of data.
140  *              Before posting the buffer to the adapter, the driver sets a three-byte
141  *              packet request header (PRH) which is required by the Motorola MAC chip
142  *              used on the adapters.  The PRH tells the MAC the type of token to
143  *              receive/send, whether or not to generate and append the CRC, whether
144  *              synchronous or asynchronous framing is used, etc.  Since the PRH
145  *              definition is not necessarily consistent across all FDDI chipsets,
146  *              the driver, rather than the common FDDI packet handler routines,
147  *              sets these bytes.
148  *
149  *              To reduce the amount of descriptor fetches needed per transmit request,
150  *              the driver takes advantage of the fact that there are at least three
151  *              bytes available before the skb->data field on the outgoing transmit
152  *              request.  This is guaranteed by having fddi_setup() in net_init.c set
153  *              dev->hard_header_len to 24 bytes.  21 bytes accounts for the largest
154  *              header in an 802.2 SNAP frame.  The other 3 bytes are the extra "pad"
155  *              bytes which we'll use to store the PRH.
156  *
157  *              There's a subtle advantage to adding these pad bytes to the
158  *              hard_header_len, it ensures that the data portion of the packet for
159  *              an 802.2 SNAP frame is longword aligned.  Other FDDI driver
160  *              implementations may not need the extra padding and can start copying
161  *              or DMAing directly from the FC byte which starts at skb->data.  Should
162  *              another driver implementation need ADDITIONAL padding, the net_init.c
163  *              module should be updated and dev->hard_header_len should be increased.
164  *              NOTE: To maintain the alignment on the data portion of the packet,
165  *              dev->hard_header_len should always be evenly divisible by 4 and at
166  *              least 24 bytes in size.
167  *
168  * Modification History:
169  *              Date            Name    Description
170  *              16-Aug-96       LVS             Created.
171  *              20-Aug-96       LVS             Updated dfx_probe so that version information
172  *                                                      string is only displayed if 1 or more cards are
173  *                                                      found.  Changed dfx_rcv_queue_process to copy
174  *                                                      3 NULL bytes before FC to ensure that data is
175  *                                                      longword aligned in receive buffer.
176  *              09-Sep-96       LVS             Updated dfx_ctl_set_multicast_list to enable
177  *                                                      LLC group promiscuous mode if multicast list
178  *                                                      is too large.  LLC individual/group promiscuous
179  *                                                      mode is now disabled if IFF_PROMISC flag not set.
180  *                                                      dfx_xmt_queue_pkt no longer checks for NULL skb
181  *                                                      on Alan Cox recommendation.  Added node address
182  *                                                      override support.
183  *              12-Sep-96       LVS             Reset current address to factory address during
184  *                                                      device open.  Updated transmit path to post a
185  *                                                      single fragment which includes PRH->end of data.
186  *              Mar 2000        AC              Did various cleanups for 2.3.x
187  *              Jun 2000        jgarzik         PCI and resource alloc cleanups
188  *              Jul 2000        tjeerd          Much cleanup and some bug fixes
189  *              Sep 2000        tjeerd          Fix leak on unload, cosmetic code cleanup
190  *              Feb 2001                        Skb allocation fixes
191  *              Feb 2001        davej           PCI enable cleanups.
192  *              04 Aug 2003     macro           Converted to the DMA API.
193  *              14 Aug 2004     macro           Fix device names reported.
194  *              14 Jun 2005     macro           Use irqreturn_t.
195  */
196
197 /* Include files */
198
199 #include <linux/module.h>
200 #include <linux/kernel.h>
201 #include <linux/string.h>
202 #include <linux/errno.h>
203 #include <linux/ioport.h>
204 #include <linux/slab.h>
205 #include <linux/interrupt.h>
206 #include <linux/pci.h>
207 #include <linux/delay.h>
208 #include <linux/init.h>
209 #include <linux/netdevice.h>
210 #include <linux/fddidevice.h>
211 #include <linux/skbuff.h>
212 #include <linux/bitops.h>
213
214 #include <asm/byteorder.h>
215 #include <asm/io.h>
216
217 #include "defxx.h"
218
219 /* Version information string should be updated prior to each new release!  */
220 #define DRV_NAME "defxx"
221 #define DRV_VERSION "v1.08"
222 #define DRV_RELDATE "2005/06/14"
223
224 static char version[] __devinitdata =
225         DRV_NAME ": " DRV_VERSION " " DRV_RELDATE
226         "  Lawrence V. Stefani and others\n";
227
228 #define DYNAMIC_BUFFERS 1
229
230 #define SKBUFF_RX_COPYBREAK 200
231 /*
232  * NEW_SKB_SIZE = PI_RCV_DATA_K_SIZE_MAX+128 to allow 128 byte
233  * alignment for compatibility with old EISA boards.
234  */
235 #define NEW_SKB_SIZE (PI_RCV_DATA_K_SIZE_MAX+128)
236
237 /* Define module-wide (static) routines */
238
239 static void             dfx_bus_init(struct net_device *dev);
240 static void             dfx_bus_config_check(DFX_board_t *bp);
241
242 static int              dfx_driver_init(struct net_device *dev, const char *print_name);
243 static int              dfx_adap_init(DFX_board_t *bp, int get_buffers);
244
245 static int              dfx_open(struct net_device *dev);
246 static int              dfx_close(struct net_device *dev);
247
248 static void             dfx_int_pr_halt_id(DFX_board_t *bp);
249 static void             dfx_int_type_0_process(DFX_board_t *bp);
250 static void             dfx_int_common(struct net_device *dev);
251 static irqreturn_t      dfx_interrupt(int irq, void *dev_id);
252
253 static struct           net_device_stats *dfx_ctl_get_stats(struct net_device *dev);
254 static void             dfx_ctl_set_multicast_list(struct net_device *dev);
255 static int              dfx_ctl_set_mac_address(struct net_device *dev, void *addr);
256 static int              dfx_ctl_update_cam(DFX_board_t *bp);
257 static int              dfx_ctl_update_filters(DFX_board_t *bp);
258
259 static int              dfx_hw_dma_cmd_req(DFX_board_t *bp);
260 static int              dfx_hw_port_ctrl_req(DFX_board_t *bp, PI_UINT32 command, PI_UINT32 data_a, PI_UINT32 data_b, PI_UINT32 *host_data);
261 static void             dfx_hw_adap_reset(DFX_board_t *bp, PI_UINT32 type);
262 static int              dfx_hw_adap_state_rd(DFX_board_t *bp);
263 static int              dfx_hw_dma_uninit(DFX_board_t *bp, PI_UINT32 type);
264
265 static int              dfx_rcv_init(DFX_board_t *bp, int get_buffers);
266 static void             dfx_rcv_queue_process(DFX_board_t *bp);
267 static void             dfx_rcv_flush(DFX_board_t *bp);
268
269 static int              dfx_xmt_queue_pkt(struct sk_buff *skb, struct net_device *dev);
270 static int              dfx_xmt_done(DFX_board_t *bp);
271 static void             dfx_xmt_flush(DFX_board_t *bp);
272
273 /* Define module-wide (static) variables */
274
275 static struct net_device *root_dfx_eisa_dev;
276
277
278 /*
279  * =======================
280  * = dfx_port_write_byte =
281  * = dfx_port_read_byte  =
282  * = dfx_port_write_long =
283  * = dfx_port_read_long  =
284  * =======================
285  *
286  * Overview:
287  *   Routines for reading and writing values from/to adapter
288  *
289  * Returns:
290  *   None
291  *
292  * Arguments:
293  *   bp     - pointer to board information
294  *   offset - register offset from base I/O address
295  *   data   - for dfx_port_write_byte and dfx_port_write_long, this
296  *                        is a value to write.
297  *                        for dfx_port_read_byte and dfx_port_read_byte, this
298  *                        is a pointer to store the read value.
299  *
300  * Functional Description:
301  *   These routines perform the correct operation to read or write
302  *   the adapter register.
303  *
304  *   EISA port block base addresses are based on the slot number in which the
305  *   controller is installed.  For example, if the EISA controller is installed
306  *   in slot 4, the port block base address is 0x4000.  If the controller is
307  *   installed in slot 2, the port block base address is 0x2000, and so on.
308  *   This port block can be used to access PDQ, ESIC, and DEFEA on-board
309  *   registers using the register offsets defined in DEFXX.H.
310  *
311  *   PCI port block base addresses are assigned by the PCI BIOS or system
312  *       firmware.  There is one 128 byte port block which can be accessed.  It
313  *   allows for I/O mapping of both PDQ and PFI registers using the register
314  *   offsets defined in DEFXX.H.
315  *
316  * Return Codes:
317  *   None
318  *
319  * Assumptions:
320  *   bp->base_addr is a valid base I/O address for this adapter.
321  *   offset is a valid register offset for this adapter.
322  *
323  * Side Effects:
324  *   Rather than produce macros for these functions, these routines
325  *   are defined using "inline" to ensure that the compiler will
326  *   generate inline code and not waste a procedure call and return.
327  *   This provides all the benefits of macros, but with the
328  *   advantage of strict data type checking.
329  */
330
331 static inline void dfx_port_write_byte(
332         DFX_board_t     *bp,
333         int                     offset,
334         u8                      data
335         )
336
337         {
338         u16 port = bp->base_addr + offset;
339
340         outb(data, port);
341         }
342
343 static inline void dfx_port_read_byte(
344         DFX_board_t     *bp,
345         int                     offset,
346         u8                      *data
347         )
348
349         {
350         u16 port = bp->base_addr + offset;
351
352         *data = inb(port);
353         }
354
355 static inline void dfx_port_write_long(
356         DFX_board_t     *bp,
357         int                     offset,
358         u32                     data
359         )
360
361         {
362         u16 port = bp->base_addr + offset;
363
364         outl(data, port);
365         }
366
367 static inline void dfx_port_read_long(
368         DFX_board_t     *bp,
369         int                     offset,
370         u32                     *data
371         )
372
373         {
374         u16 port = bp->base_addr + offset;
375
376         *data = inl(port);
377         }
378
379
380 /*
381  * =============
382  * = dfx_init_one_pci_or_eisa =
383  * =============
384  *
385  * Overview:
386  *   Initializes a supported FDDI EISA or PCI controller
387  *
388  * Returns:
389  *   Condition code
390  *
391  * Arguments:
392  *   pdev - pointer to pci device information (NULL for EISA)
393  *   ioaddr - pointer to port (NULL for PCI)
394  *
395  * Functional Description:
396  *
397  * Return Codes:
398  *   0           - This device (fddi0, fddi1, etc) configured successfully
399  *   -EBUSY      - Failed to get resources, or dfx_driver_init failed.
400  *
401  * Assumptions:
402  *   It compiles so it should work :-( (PCI cards do :-)
403  *
404  * Side Effects:
405  *   Device structures for FDDI adapters (fddi0, fddi1, etc) are
406  *   initialized and the board resources are read and stored in
407  *   the device structure.
408  */
409 static int __devinit dfx_init_one_pci_or_eisa(struct pci_dev *pdev, long ioaddr)
410 {
411         static int version_disp;
412         char *print_name = DRV_NAME;
413         struct net_device *dev;
414         DFX_board_t       *bp;                  /* board pointer */
415         int alloc_size;                         /* total buffer size used */
416         int err;
417
418         if (!version_disp) {    /* display version info if adapter is found */
419                 version_disp = 1;       /* set display flag to TRUE so that */
420                 printk(version);        /* we only display this string ONCE */
421         }
422
423         if (pdev != NULL)
424                 print_name = pci_name(pdev);
425
426         dev = alloc_fddidev(sizeof(*bp));
427         if (!dev) {
428                 printk(KERN_ERR "%s: unable to allocate fddidev, aborting\n",
429                        print_name);
430                 return -ENOMEM;
431         }
432
433         /* Enable PCI device. */
434         if (pdev != NULL) {
435                 err = pci_enable_device (pdev);
436                 if (err) goto err_out;
437                 ioaddr = pci_resource_start (pdev, 1);
438         }
439
440         SET_MODULE_OWNER(dev);
441         if (pdev != NULL)
442                 SET_NETDEV_DEV(dev, &pdev->dev);
443
444         bp = dev->priv;
445
446         if (!request_region(ioaddr,
447                             pdev ? PFI_K_CSR_IO_LEN : PI_ESIC_K_CSR_IO_LEN,
448                             print_name)) {
449                 printk(KERN_ERR "%s: Cannot reserve I/O resource "
450                        "0x%x @ 0x%lx, aborting\n", print_name,
451                        pdev ? PFI_K_CSR_IO_LEN : PI_ESIC_K_CSR_IO_LEN, ioaddr);
452                 err = -EBUSY;
453                 goto err_out;
454         }
455
456         /* Initialize new device structure */
457
458         dev->base_addr                  = ioaddr; /* save port (I/O) base address */
459
460         dev->get_stats                  = dfx_ctl_get_stats;
461         dev->open                       = dfx_open;
462         dev->stop                       = dfx_close;
463         dev->hard_start_xmit            = dfx_xmt_queue_pkt;
464         dev->set_multicast_list         = dfx_ctl_set_multicast_list;
465         dev->set_mac_address            = dfx_ctl_set_mac_address;
466
467         if (pdev == NULL) {
468                 /* EISA board */
469                 bp->bus_type = DFX_BUS_TYPE_EISA;
470                 bp->next = root_dfx_eisa_dev;
471                 root_dfx_eisa_dev = dev;
472         } else {
473                 /* PCI board */
474                 bp->bus_type = DFX_BUS_TYPE_PCI;
475                 bp->pci_dev = pdev;
476                 pci_set_drvdata (pdev, dev);
477                 pci_set_master (pdev);
478         }
479
480         if (dfx_driver_init(dev, print_name) != DFX_K_SUCCESS) {
481                 err = -ENODEV;
482                 goto err_out_region;
483         }
484
485         err = register_netdev(dev);
486         if (err)
487                 goto err_out_kfree;
488
489         printk("%s: registered as %s\n", print_name, dev->name);
490         return 0;
491
492 err_out_kfree:
493         alloc_size = sizeof(PI_DESCR_BLOCK) +
494                      PI_CMD_REQ_K_SIZE_MAX + PI_CMD_RSP_K_SIZE_MAX +
495 #ifndef DYNAMIC_BUFFERS
496                      (bp->rcv_bufs_to_post * PI_RCV_DATA_K_SIZE_MAX) +
497 #endif
498                      sizeof(PI_CONSUMER_BLOCK) +
499                      (PI_ALIGN_K_DESC_BLK - 1);
500         if (bp->kmalloced)
501                 pci_free_consistent(pdev, alloc_size,
502                                     bp->kmalloced, bp->kmalloced_dma);
503 err_out_region:
504         release_region(ioaddr, pdev ? PFI_K_CSR_IO_LEN : PI_ESIC_K_CSR_IO_LEN);
505 err_out:
506         free_netdev(dev);
507         return err;
508 }
509
510 static int __devinit dfx_init_one(struct pci_dev *pdev, const struct pci_device_id *ent)
511 {
512         return dfx_init_one_pci_or_eisa(pdev, 0);
513 }
514
515 static int __init dfx_eisa_init(void)
516 {
517         int rc = -ENODEV;
518         int i;                  /* used in for loops */
519         u16 port;               /* temporary I/O (port) address */
520         u32 slot_id;            /* EISA hardware (slot) ID read from adapter */
521
522         DBG_printk("In dfx_eisa_init...\n");
523
524         /* Scan for FDDI EISA controllers */
525
526         for (i=0; i < DFX_MAX_EISA_SLOTS; i++)          /* only scan for up to 16 EISA slots */
527         {
528                 port = (i << 12) + PI_ESIC_K_SLOT_ID;   /* port = I/O address for reading slot ID */
529                 slot_id = inl(port);                                    /* read EISA HW (slot) ID */
530                 if ((slot_id & 0xF0FFFFFF) == DEFEA_PRODUCT_ID)
531                 {
532                         port = (i << 12);                                       /* recalc base addr */
533
534                         if (dfx_init_one_pci_or_eisa(NULL, port) == 0) rc = 0;
535                 }
536         }
537         return rc;
538 }
539
540 /*
541  * ================
542  * = dfx_bus_init =
543  * ================
544  *
545  * Overview:
546  *   Initializes EISA and PCI controller bus-specific logic.
547  *
548  * Returns:
549  *   None
550  *
551  * Arguments:
552  *   dev - pointer to device information
553  *
554  * Functional Description:
555  *   Determine and save adapter IRQ in device table,
556  *   then perform bus-specific logic initialization.
557  *
558  * Return Codes:
559  *   None
560  *
561  * Assumptions:
562  *   dev->base_addr has already been set with the proper
563  *       base I/O address for this device.
564  *
565  * Side Effects:
566  *   Interrupts are enabled at the adapter bus-specific logic.
567  *   Note:  Interrupts at the DMA engine (PDQ chip) are not
568  *   enabled yet.
569  */
570
571 static void __devinit dfx_bus_init(struct net_device *dev)
572 {
573         DFX_board_t *bp = dev->priv;
574         u8                      val;    /* used for I/O read/writes */
575
576         DBG_printk("In dfx_bus_init...\n");
577
578         /*
579          * Initialize base I/O address field in bp structure
580          *
581          * Note: bp->base_addr is the same as dev->base_addr.
582          *               It's useful because often we'll need to read
583          *               or write registers where we already have the
584          *               bp pointer instead of the dev pointer.  Having
585          *               the base address in the bp structure will
586          *               save a pointer dereference.
587          *
588          *               IMPORTANT!! This field must be defined before
589          *               any of the dfx_port_* inline functions are
590          *               called.
591          */
592
593         bp->base_addr = dev->base_addr;
594
595         /* And a pointer back to the net_device struct */
596         bp->dev = dev;
597
598         /* Initialize adapter based on bus type */
599
600         if (bp->bus_type == DFX_BUS_TYPE_EISA)
601                 {
602                 /* Get the interrupt level from the ESIC chip */
603
604                 dfx_port_read_byte(bp, PI_ESIC_K_IO_CONFIG_STAT_0, &val);
605                 switch ((val & PI_CONFIG_STAT_0_M_IRQ) >> PI_CONFIG_STAT_0_V_IRQ)
606                         {
607                         case PI_CONFIG_STAT_0_IRQ_K_9:
608                                 dev->irq = 9;
609                                 break;
610
611                         case PI_CONFIG_STAT_0_IRQ_K_10:
612                                 dev->irq = 10;
613                                 break;
614
615                         case PI_CONFIG_STAT_0_IRQ_K_11:
616                                 dev->irq = 11;
617                                 break;
618
619                         case PI_CONFIG_STAT_0_IRQ_K_15:
620                                 dev->irq = 15;
621                                 break;
622                         }
623
624                 /* Enable access to I/O on the board by writing 0x03 to Function Control Register */
625
626                 dfx_port_write_byte(bp, PI_ESIC_K_FUNCTION_CNTRL, PI_ESIC_K_FUNCTION_CNTRL_IO_ENB);
627
628                 /* Set the I/O decode range of the board */
629
630                 val = ((dev->base_addr >> 12) << PI_IO_CMP_V_SLOT);
631                 dfx_port_write_byte(bp, PI_ESIC_K_IO_CMP_0_1, val);
632                 dfx_port_write_byte(bp, PI_ESIC_K_IO_CMP_1_1, val);
633
634                 /* Enable access to rest of module (including PDQ and packet memory) */
635
636                 dfx_port_write_byte(bp, PI_ESIC_K_SLOT_CNTRL, PI_SLOT_CNTRL_M_ENB);
637
638                 /*
639                  * Map PDQ registers into I/O space.  This is done by clearing a bit
640                  * in Burst Holdoff register.
641                  */
642
643                 dfx_port_read_byte(bp, PI_ESIC_K_BURST_HOLDOFF, &val);
644                 dfx_port_write_byte(bp, PI_ESIC_K_BURST_HOLDOFF, (val & ~PI_BURST_HOLDOFF_M_MEM_MAP));
645
646                 /* Enable interrupts at EISA bus interface chip (ESIC) */
647
648                 dfx_port_read_byte(bp, PI_ESIC_K_IO_CONFIG_STAT_0, &val);
649                 dfx_port_write_byte(bp, PI_ESIC_K_IO_CONFIG_STAT_0, (val | PI_CONFIG_STAT_0_M_INT_ENB));
650                 }
651         else
652                 {
653                 struct pci_dev *pdev = bp->pci_dev;
654
655                 /* Get the interrupt level from the PCI Configuration Table */
656
657                 dev->irq = pdev->irq;
658
659                 /* Check Latency Timer and set if less than minimal */
660
661                 pci_read_config_byte(pdev, PCI_LATENCY_TIMER, &val);
662                 if (val < PFI_K_LAT_TIMER_MIN)  /* if less than min, override with default */
663                         {
664                         val = PFI_K_LAT_TIMER_DEF;
665                         pci_write_config_byte(pdev, PCI_LATENCY_TIMER, val);
666                         }
667
668                 /* Enable interrupts at PCI bus interface chip (PFI) */
669
670                 dfx_port_write_long(bp, PFI_K_REG_MODE_CTRL, (PFI_MODE_M_PDQ_INT_ENB | PFI_MODE_M_DMA_ENB));
671                 }
672         }
673
674
675 /*
676  * ========================
677  * = dfx_bus_config_check =
678  * ========================
679  *
680  * Overview:
681  *   Checks the configuration (burst size, full-duplex, etc.)  If any parameters
682  *   are illegal, then this routine will set new defaults.
683  *
684  * Returns:
685  *   None
686  *
687  * Arguments:
688  *   bp - pointer to board information
689  *
690  * Functional Description:
691  *   For Revision 1 FDDI EISA, Revision 2 or later FDDI EISA with rev E or later
692  *   PDQ, and all FDDI PCI controllers, all values are legal.
693  *
694  * Return Codes:
695  *   None
696  *
697  * Assumptions:
698  *   dfx_adap_init has NOT been called yet so burst size and other items have
699  *   not been set.
700  *
701  * Side Effects:
702  *   None
703  */
704
705 static void __devinit dfx_bus_config_check(DFX_board_t *bp)
706 {
707         int     status;                         /* return code from adapter port control call */
708         u32     slot_id;                        /* EISA-bus hardware id (DEC3001, DEC3002,...) */
709         u32     host_data;                      /* LW data returned from port control call */
710
711         DBG_printk("In dfx_bus_config_check...\n");
712
713         /* Configuration check only valid for EISA adapter */
714
715         if (bp->bus_type == DFX_BUS_TYPE_EISA)
716                 {
717                 dfx_port_read_long(bp, PI_ESIC_K_SLOT_ID, &slot_id);
718
719                 /*
720                  * First check if revision 2 EISA controller.  Rev. 1 cards used
721                  * PDQ revision B, so no workaround needed in this case.  Rev. 3
722                  * cards used PDQ revision E, so no workaround needed in this
723                  * case, either.  Only Rev. 2 cards used either Rev. D or E
724                  * chips, so we must verify the chip revision on Rev. 2 cards.
725                  */
726
727                 if (slot_id == DEFEA_PROD_ID_2)
728                         {
729                         /*
730                          * Revision 2 FDDI EISA controller found, so let's check PDQ
731                          * revision of adapter.
732                          */
733
734                         status = dfx_hw_port_ctrl_req(bp,
735                                                                                         PI_PCTRL_M_SUB_CMD,
736                                                                                         PI_SUB_CMD_K_PDQ_REV_GET,
737                                                                                         0,
738                                                                                         &host_data);
739                         if ((status != DFX_K_SUCCESS) || (host_data == 2))
740                                 {
741                                 /*
742                                  * Either we couldn't determine the PDQ revision, or
743                                  * we determined that it is at revision D.  In either case,
744                                  * we need to implement the workaround.
745                                  */
746
747                                 /* Ensure that the burst size is set to 8 longwords or less */
748
749                                 switch (bp->burst_size)
750                                         {
751                                         case PI_PDATA_B_DMA_BURST_SIZE_32:
752                                         case PI_PDATA_B_DMA_BURST_SIZE_16:
753                                                 bp->burst_size = PI_PDATA_B_DMA_BURST_SIZE_8;
754                                                 break;
755
756                                         default:
757                                                 break;
758                                         }
759
760                                 /* Ensure that full-duplex mode is not enabled */
761
762                                 bp->full_duplex_enb = PI_SNMP_K_FALSE;
763                                 }
764                         }
765                 }
766         }
767
768
769 /*
770  * ===================
771  * = dfx_driver_init =
772  * ===================
773  *
774  * Overview:
775  *   Initializes remaining adapter board structure information
776  *   and makes sure adapter is in a safe state prior to dfx_open().
777  *
778  * Returns:
779  *   Condition code
780  *
781  * Arguments:
782  *   dev - pointer to device information
783  *   print_name - printable device name
784  *
785  * Functional Description:
786  *   This function allocates additional resources such as the host memory
787  *   blocks needed by the adapter (eg. descriptor and consumer blocks).
788  *       Remaining bus initialization steps are also completed.  The adapter
789  *   is also reset so that it is in the DMA_UNAVAILABLE state.  The OS
790  *   must call dfx_open() to open the adapter and bring it on-line.
791  *
792  * Return Codes:
793  *   DFX_K_SUCCESS      - initialization succeeded
794  *   DFX_K_FAILURE      - initialization failed - could not allocate memory
795  *                                              or read adapter MAC address
796  *
797  * Assumptions:
798  *   Memory allocated from pci_alloc_consistent() call is physically
799  *   contiguous, locked memory.
800  *
801  * Side Effects:
802  *   Adapter is reset and should be in DMA_UNAVAILABLE state before
803  *   returning from this routine.
804  */
805
806 static int __devinit dfx_driver_init(struct net_device *dev,
807                                      const char *print_name)
808 {
809         DFX_board_t *bp = dev->priv;
810         int                     alloc_size;                     /* total buffer size needed */
811         char            *top_v, *curr_v;        /* virtual addrs into memory block */
812         dma_addr_t              top_p, curr_p;          /* physical addrs into memory block */
813         u32                     data;                           /* host data register value */
814
815         DBG_printk("In dfx_driver_init...\n");
816
817         /* Initialize bus-specific hardware registers */
818
819         dfx_bus_init(dev);
820
821         /*
822          * Initialize default values for configurable parameters
823          *
824          * Note: All of these parameters are ones that a user may
825          *       want to customize.  It'd be nice to break these
826          *               out into Space.c or someplace else that's more
827          *               accessible/understandable than this file.
828          */
829
830         bp->full_duplex_enb             = PI_SNMP_K_FALSE;
831         bp->req_ttrt                    = 8 * 12500;            /* 8ms in 80 nanosec units */
832         bp->burst_size                  = PI_PDATA_B_DMA_BURST_SIZE_DEF;
833         bp->rcv_bufs_to_post    = RCV_BUFS_DEF;
834
835         /*
836          * Ensure that HW configuration is OK
837          *
838          * Note: Depending on the hardware revision, we may need to modify
839          *       some of the configurable parameters to workaround hardware
840          *       limitations.  We'll perform this configuration check AFTER
841          *       setting the parameters to their default values.
842          */
843
844         dfx_bus_config_check(bp);
845
846         /* Disable PDQ interrupts first */
847
848         dfx_port_write_long(bp, PI_PDQ_K_REG_HOST_INT_ENB, PI_HOST_INT_K_DISABLE_ALL_INTS);
849
850         /* Place adapter in DMA_UNAVAILABLE state by resetting adapter */
851
852         (void) dfx_hw_dma_uninit(bp, PI_PDATA_A_RESET_M_SKIP_ST);
853
854         /*  Read the factory MAC address from the adapter then save it */
855
856         if (dfx_hw_port_ctrl_req(bp, PI_PCTRL_M_MLA, PI_PDATA_A_MLA_K_LO, 0,
857                                  &data) != DFX_K_SUCCESS) {
858                 printk("%s: Could not read adapter factory MAC address!\n",
859                        print_name);
860                 return(DFX_K_FAILURE);
861         }
862         memcpy(&bp->factory_mac_addr[0], &data, sizeof(u32));
863
864         if (dfx_hw_port_ctrl_req(bp, PI_PCTRL_M_MLA, PI_PDATA_A_MLA_K_HI, 0,
865                                  &data) != DFX_K_SUCCESS) {
866                 printk("%s: Could not read adapter factory MAC address!\n",
867                        print_name);
868                 return(DFX_K_FAILURE);
869         }
870         memcpy(&bp->factory_mac_addr[4], &data, sizeof(u16));
871
872         /*
873          * Set current address to factory address
874          *
875          * Note: Node address override support is handled through
876          *       dfx_ctl_set_mac_address.
877          */
878
879         memcpy(dev->dev_addr, bp->factory_mac_addr, FDDI_K_ALEN);
880         if (bp->bus_type == DFX_BUS_TYPE_EISA)
881                 printk("%s: DEFEA at I/O addr = 0x%lX, IRQ = %d, "
882                        "Hardware addr = %02X-%02X-%02X-%02X-%02X-%02X\n",
883                        print_name, dev->base_addr, dev->irq,
884                        dev->dev_addr[0], dev->dev_addr[1],
885                        dev->dev_addr[2], dev->dev_addr[3],
886                        dev->dev_addr[4], dev->dev_addr[5]);
887         else
888                 printk("%s: DEFPA at I/O addr = 0x%lX, IRQ = %d, "
889                        "Hardware addr = %02X-%02X-%02X-%02X-%02X-%02X\n",
890                        print_name, dev->base_addr, dev->irq,
891                        dev->dev_addr[0], dev->dev_addr[1],
892                        dev->dev_addr[2], dev->dev_addr[3],
893                        dev->dev_addr[4], dev->dev_addr[5]);
894
895         /*
896          * Get memory for descriptor block, consumer block, and other buffers
897          * that need to be DMA read or written to by the adapter.
898          */
899
900         alloc_size = sizeof(PI_DESCR_BLOCK) +
901                                         PI_CMD_REQ_K_SIZE_MAX +
902                                         PI_CMD_RSP_K_SIZE_MAX +
903 #ifndef DYNAMIC_BUFFERS
904                                         (bp->rcv_bufs_to_post * PI_RCV_DATA_K_SIZE_MAX) +
905 #endif
906                                         sizeof(PI_CONSUMER_BLOCK) +
907                                         (PI_ALIGN_K_DESC_BLK - 1);
908         bp->kmalloced = top_v = pci_alloc_consistent(bp->pci_dev, alloc_size,
909                                                      &bp->kmalloced_dma);
910         if (top_v == NULL) {
911                 printk("%s: Could not allocate memory for host buffers "
912                        "and structures!\n", print_name);
913                 return(DFX_K_FAILURE);
914         }
915         memset(top_v, 0, alloc_size);   /* zero out memory before continuing */
916         top_p = bp->kmalloced_dma;      /* get physical address of buffer */
917
918         /*
919          *  To guarantee the 8K alignment required for the descriptor block, 8K - 1
920          *  plus the amount of memory needed was allocated.  The physical address
921          *      is now 8K aligned.  By carving up the memory in a specific order,
922          *  we'll guarantee the alignment requirements for all other structures.
923          *
924          *  Note: If the assumptions change regarding the non-paged, non-cached,
925          *                physically contiguous nature of the memory block or the address
926          *                alignments, then we'll need to implement a different algorithm
927          *                for allocating the needed memory.
928          */
929
930         curr_p = ALIGN(top_p, PI_ALIGN_K_DESC_BLK);
931         curr_v = top_v + (curr_p - top_p);
932
933         /* Reserve space for descriptor block */
934
935         bp->descr_block_virt = (PI_DESCR_BLOCK *) curr_v;
936         bp->descr_block_phys = curr_p;
937         curr_v += sizeof(PI_DESCR_BLOCK);
938         curr_p += sizeof(PI_DESCR_BLOCK);
939
940         /* Reserve space for command request buffer */
941
942         bp->cmd_req_virt = (PI_DMA_CMD_REQ *) curr_v;
943         bp->cmd_req_phys = curr_p;
944         curr_v += PI_CMD_REQ_K_SIZE_MAX;
945         curr_p += PI_CMD_REQ_K_SIZE_MAX;
946
947         /* Reserve space for command response buffer */
948
949         bp->cmd_rsp_virt = (PI_DMA_CMD_RSP *) curr_v;
950         bp->cmd_rsp_phys = curr_p;
951         curr_v += PI_CMD_RSP_K_SIZE_MAX;
952         curr_p += PI_CMD_RSP_K_SIZE_MAX;
953
954         /* Reserve space for the LLC host receive queue buffers */
955
956         bp->rcv_block_virt = curr_v;
957         bp->rcv_block_phys = curr_p;
958
959 #ifndef DYNAMIC_BUFFERS
960         curr_v += (bp->rcv_bufs_to_post * PI_RCV_DATA_K_SIZE_MAX);
961         curr_p += (bp->rcv_bufs_to_post * PI_RCV_DATA_K_SIZE_MAX);
962 #endif
963
964         /* Reserve space for the consumer block */
965
966         bp->cons_block_virt = (PI_CONSUMER_BLOCK *) curr_v;
967         bp->cons_block_phys = curr_p;
968
969         /* Display virtual and physical addresses if debug driver */
970
971         DBG_printk("%s: Descriptor block virt = %0lX, phys = %0X\n",
972                    print_name,
973                    (long)bp->descr_block_virt, bp->descr_block_phys);
974         DBG_printk("%s: Command Request buffer virt = %0lX, phys = %0X\n",
975                    print_name, (long)bp->cmd_req_virt, bp->cmd_req_phys);
976         DBG_printk("%s: Command Response buffer virt = %0lX, phys = %0X\n",
977                    print_name, (long)bp->cmd_rsp_virt, bp->cmd_rsp_phys);
978         DBG_printk("%s: Receive buffer block virt = %0lX, phys = %0X\n",
979                    print_name, (long)bp->rcv_block_virt, bp->rcv_block_phys);
980         DBG_printk("%s: Consumer block virt = %0lX, phys = %0X\n",
981                    print_name, (long)bp->cons_block_virt, bp->cons_block_phys);
982
983         return(DFX_K_SUCCESS);
984 }
985
986
987 /*
988  * =================
989  * = dfx_adap_init =
990  * =================
991  *
992  * Overview:
993  *   Brings the adapter to the link avail/link unavailable state.
994  *
995  * Returns:
996  *   Condition code
997  *
998  * Arguments:
999  *   bp - pointer to board information
1000  *   get_buffers - non-zero if buffers to be allocated
1001  *
1002  * Functional Description:
1003  *   Issues the low-level firmware/hardware calls necessary to bring
1004  *   the adapter up, or to properly reset and restore adapter during
1005  *   run-time.
1006  *
1007  * Return Codes:
1008  *   DFX_K_SUCCESS - Adapter brought up successfully
1009  *   DFX_K_FAILURE - Adapter initialization failed
1010  *
1011  * Assumptions:
1012  *   bp->reset_type should be set to a valid reset type value before
1013  *   calling this routine.
1014  *
1015  * Side Effects:
1016  *   Adapter should be in LINK_AVAILABLE or LINK_UNAVAILABLE state
1017  *   upon a successful return of this routine.
1018  */
1019
1020 static int dfx_adap_init(DFX_board_t *bp, int get_buffers)
1021         {
1022         DBG_printk("In dfx_adap_init...\n");
1023
1024         /* Disable PDQ interrupts first */
1025
1026         dfx_port_write_long(bp, PI_PDQ_K_REG_HOST_INT_ENB, PI_HOST_INT_K_DISABLE_ALL_INTS);
1027
1028         /* Place adapter in DMA_UNAVAILABLE state by resetting adapter */
1029
1030         if (dfx_hw_dma_uninit(bp, bp->reset_type) != DFX_K_SUCCESS)
1031                 {
1032                 printk("%s: Could not uninitialize/reset adapter!\n", bp->dev->name);
1033                 return(DFX_K_FAILURE);
1034                 }
1035
1036         /*
1037          * When the PDQ is reset, some false Type 0 interrupts may be pending,
1038          * so we'll acknowledge all Type 0 interrupts now before continuing.
1039          */
1040
1041         dfx_port_write_long(bp, PI_PDQ_K_REG_TYPE_0_STATUS, PI_HOST_INT_K_ACK_ALL_TYPE_0);
1042
1043         /*
1044          * Clear Type 1 and Type 2 registers before going to DMA_AVAILABLE state
1045          *
1046          * Note: We only need to clear host copies of these registers.  The PDQ reset
1047          *       takes care of the on-board register values.
1048          */
1049
1050         bp->cmd_req_reg.lword   = 0;
1051         bp->cmd_rsp_reg.lword   = 0;
1052         bp->rcv_xmt_reg.lword   = 0;
1053
1054         /* Clear consumer block before going to DMA_AVAILABLE state */
1055
1056         memset(bp->cons_block_virt, 0, sizeof(PI_CONSUMER_BLOCK));
1057
1058         /* Initialize the DMA Burst Size */
1059
1060         if (dfx_hw_port_ctrl_req(bp,
1061                                                         PI_PCTRL_M_SUB_CMD,
1062                                                         PI_SUB_CMD_K_BURST_SIZE_SET,
1063                                                         bp->burst_size,
1064                                                         NULL) != DFX_K_SUCCESS)
1065                 {
1066                 printk("%s: Could not set adapter burst size!\n", bp->dev->name);
1067                 return(DFX_K_FAILURE);
1068                 }
1069
1070         /*
1071          * Set base address of Consumer Block
1072          *
1073          * Assumption: 32-bit physical address of consumer block is 64 byte
1074          *                         aligned.  That is, bits 0-5 of the address must be zero.
1075          */
1076
1077         if (dfx_hw_port_ctrl_req(bp,
1078                                                         PI_PCTRL_M_CONS_BLOCK,
1079                                                         bp->cons_block_phys,
1080                                                         0,
1081                                                         NULL) != DFX_K_SUCCESS)
1082                 {
1083                 printk("%s: Could not set consumer block address!\n", bp->dev->name);
1084                 return(DFX_K_FAILURE);
1085                 }
1086
1087         /*
1088          * Set base address of Descriptor Block and bring adapter to DMA_AVAILABLE state
1089          *
1090          * Note: We also set the literal and data swapping requirements in this
1091          *           command.  Since this driver presently runs on Intel platforms
1092          *               which are Little Endian, we'll tell the adapter to byte swap
1093          *               data only.  This code will need to change when we support
1094          *               Big Endian systems (eg. PowerPC).
1095          *
1096          * Assumption: 32-bit physical address of descriptor block is 8Kbyte
1097          *             aligned.  That is, bits 0-12 of the address must be zero.
1098          */
1099
1100         if (dfx_hw_port_ctrl_req(bp,
1101                                                         PI_PCTRL_M_INIT,
1102                                                         (u32) (bp->descr_block_phys | PI_PDATA_A_INIT_M_BSWAP_DATA),
1103                                                         0,
1104                                                         NULL) != DFX_K_SUCCESS)
1105                 {
1106                 printk("%s: Could not set descriptor block address!\n", bp->dev->name);
1107                 return(DFX_K_FAILURE);
1108                 }
1109
1110         /* Set transmit flush timeout value */
1111
1112         bp->cmd_req_virt->cmd_type = PI_CMD_K_CHARS_SET;
1113         bp->cmd_req_virt->char_set.item[0].item_code    = PI_ITEM_K_FLUSH_TIME;
1114         bp->cmd_req_virt->char_set.item[0].value                = 3;    /* 3 seconds */
1115         bp->cmd_req_virt->char_set.item[0].item_index   = 0;
1116         bp->cmd_req_virt->char_set.item[1].item_code    = PI_ITEM_K_EOL;
1117         if (dfx_hw_dma_cmd_req(bp) != DFX_K_SUCCESS)
1118                 {
1119                 printk("%s: DMA command request failed!\n", bp->dev->name);
1120                 return(DFX_K_FAILURE);
1121                 }
1122
1123         /* Set the initial values for eFDXEnable and MACTReq MIB objects */
1124
1125         bp->cmd_req_virt->cmd_type = PI_CMD_K_SNMP_SET;
1126         bp->cmd_req_virt->snmp_set.item[0].item_code    = PI_ITEM_K_FDX_ENB_DIS;
1127         bp->cmd_req_virt->snmp_set.item[0].value                = bp->full_duplex_enb;
1128         bp->cmd_req_virt->snmp_set.item[0].item_index   = 0;
1129         bp->cmd_req_virt->snmp_set.item[1].item_code    = PI_ITEM_K_MAC_T_REQ;
1130         bp->cmd_req_virt->snmp_set.item[1].value                = bp->req_ttrt;
1131         bp->cmd_req_virt->snmp_set.item[1].item_index   = 0;
1132         bp->cmd_req_virt->snmp_set.item[2].item_code    = PI_ITEM_K_EOL;
1133         if (dfx_hw_dma_cmd_req(bp) != DFX_K_SUCCESS)
1134                 {
1135                 printk("%s: DMA command request failed!\n", bp->dev->name);
1136                 return(DFX_K_FAILURE);
1137                 }
1138
1139         /* Initialize adapter CAM */
1140
1141         if (dfx_ctl_update_cam(bp) != DFX_K_SUCCESS)
1142                 {
1143                 printk("%s: Adapter CAM update failed!\n", bp->dev->name);
1144                 return(DFX_K_FAILURE);
1145                 }
1146
1147         /* Initialize adapter filters */
1148
1149         if (dfx_ctl_update_filters(bp) != DFX_K_SUCCESS)
1150                 {
1151                 printk("%s: Adapter filters update failed!\n", bp->dev->name);
1152                 return(DFX_K_FAILURE);
1153                 }
1154
1155         /*
1156          * Remove any existing dynamic buffers (i.e. if the adapter is being
1157          * reinitialized)
1158          */
1159
1160         if (get_buffers)
1161                 dfx_rcv_flush(bp);
1162
1163         /* Initialize receive descriptor block and produce buffers */
1164
1165         if (dfx_rcv_init(bp, get_buffers))
1166                 {
1167                 printk("%s: Receive buffer allocation failed\n", bp->dev->name);
1168                 if (get_buffers)
1169                         dfx_rcv_flush(bp);
1170                 return(DFX_K_FAILURE);
1171                 }
1172
1173         /* Issue START command and bring adapter to LINK_(UN)AVAILABLE state */
1174
1175         bp->cmd_req_virt->cmd_type = PI_CMD_K_START;
1176         if (dfx_hw_dma_cmd_req(bp) != DFX_K_SUCCESS)
1177                 {
1178                 printk("%s: Start command failed\n", bp->dev->name);
1179                 if (get_buffers)
1180                         dfx_rcv_flush(bp);
1181                 return(DFX_K_FAILURE);
1182                 }
1183
1184         /* Initialization succeeded, reenable PDQ interrupts */
1185
1186         dfx_port_write_long(bp, PI_PDQ_K_REG_HOST_INT_ENB, PI_HOST_INT_K_ENABLE_DEF_INTS);
1187         return(DFX_K_SUCCESS);
1188         }
1189
1190
1191 /*
1192  * ============
1193  * = dfx_open =
1194  * ============
1195  *
1196  * Overview:
1197  *   Opens the adapter
1198  *
1199  * Returns:
1200  *   Condition code
1201  *
1202  * Arguments:
1203  *   dev - pointer to device information
1204  *
1205  * Functional Description:
1206  *   This function brings the adapter to an operational state.
1207  *
1208  * Return Codes:
1209  *   0           - Adapter was successfully opened
1210  *   -EAGAIN - Could not register IRQ or adapter initialization failed
1211  *
1212  * Assumptions:
1213  *   This routine should only be called for a device that was
1214  *   initialized successfully.
1215  *
1216  * Side Effects:
1217  *   Adapter should be in LINK_AVAILABLE or LINK_UNAVAILABLE state
1218  *   if the open is successful.
1219  */
1220
1221 static int dfx_open(struct net_device *dev)
1222 {
1223         int ret;
1224         DFX_board_t     *bp = dev->priv;
1225
1226         DBG_printk("In dfx_open...\n");
1227
1228         /* Register IRQ - support shared interrupts by passing device ptr */
1229
1230         ret = request_irq(dev->irq, dfx_interrupt, IRQF_SHARED, dev->name, dev);
1231         if (ret) {
1232                 printk(KERN_ERR "%s: Requested IRQ %d is busy\n", dev->name, dev->irq);
1233                 return ret;
1234         }
1235
1236         /*
1237          * Set current address to factory MAC address
1238          *
1239          * Note: We've already done this step in dfx_driver_init.
1240          *       However, it's possible that a user has set a node
1241          *               address override, then closed and reopened the
1242          *               adapter.  Unless we reset the device address field
1243          *               now, we'll continue to use the existing modified
1244          *               address.
1245          */
1246
1247         memcpy(dev->dev_addr, bp->factory_mac_addr, FDDI_K_ALEN);
1248
1249         /* Clear local unicast/multicast address tables and counts */
1250
1251         memset(bp->uc_table, 0, sizeof(bp->uc_table));
1252         memset(bp->mc_table, 0, sizeof(bp->mc_table));
1253         bp->uc_count = 0;
1254         bp->mc_count = 0;
1255
1256         /* Disable promiscuous filter settings */
1257
1258         bp->ind_group_prom      = PI_FSTATE_K_BLOCK;
1259         bp->group_prom          = PI_FSTATE_K_BLOCK;
1260
1261         spin_lock_init(&bp->lock);
1262
1263         /* Reset and initialize adapter */
1264
1265         bp->reset_type = PI_PDATA_A_RESET_M_SKIP_ST;    /* skip self-test */
1266         if (dfx_adap_init(bp, 1) != DFX_K_SUCCESS)
1267         {
1268                 printk(KERN_ERR "%s: Adapter open failed!\n", dev->name);
1269                 free_irq(dev->irq, dev);
1270                 return -EAGAIN;
1271         }
1272
1273         /* Set device structure info */
1274         netif_start_queue(dev);
1275         return(0);
1276 }
1277
1278
1279 /*
1280  * =============
1281  * = dfx_close =
1282  * =============
1283  *
1284  * Overview:
1285  *   Closes the device/module.
1286  *
1287  * Returns:
1288  *   Condition code
1289  *
1290  * Arguments:
1291  *   dev - pointer to device information
1292  *
1293  * Functional Description:
1294  *   This routine closes the adapter and brings it to a safe state.
1295  *   The interrupt service routine is deregistered with the OS.
1296  *   The adapter can be opened again with another call to dfx_open().
1297  *
1298  * Return Codes:
1299  *   Always return 0.
1300  *
1301  * Assumptions:
1302  *   No further requests for this adapter are made after this routine is
1303  *   called.  dfx_open() can be called to reset and reinitialize the
1304  *   adapter.
1305  *
1306  * Side Effects:
1307  *   Adapter should be in DMA_UNAVAILABLE state upon completion of this
1308  *   routine.
1309  */
1310
1311 static int dfx_close(struct net_device *dev)
1312 {
1313         DFX_board_t     *bp = dev->priv;
1314
1315         DBG_printk("In dfx_close...\n");
1316
1317         /* Disable PDQ interrupts first */
1318
1319         dfx_port_write_long(bp, PI_PDQ_K_REG_HOST_INT_ENB, PI_HOST_INT_K_DISABLE_ALL_INTS);
1320
1321         /* Place adapter in DMA_UNAVAILABLE state by resetting adapter */
1322
1323         (void) dfx_hw_dma_uninit(bp, PI_PDATA_A_RESET_M_SKIP_ST);
1324
1325         /*
1326          * Flush any pending transmit buffers
1327          *
1328          * Note: It's important that we flush the transmit buffers
1329          *               BEFORE we clear our copy of the Type 2 register.
1330          *               Otherwise, we'll have no idea how many buffers
1331          *               we need to free.
1332          */
1333
1334         dfx_xmt_flush(bp);
1335
1336         /*
1337          * Clear Type 1 and Type 2 registers after adapter reset
1338          *
1339          * Note: Even though we're closing the adapter, it's
1340          *       possible that an interrupt will occur after
1341          *               dfx_close is called.  Without some assurance to
1342          *               the contrary we want to make sure that we don't
1343          *               process receive and transmit LLC frames and update
1344          *               the Type 2 register with bad information.
1345          */
1346
1347         bp->cmd_req_reg.lword   = 0;
1348         bp->cmd_rsp_reg.lword   = 0;
1349         bp->rcv_xmt_reg.lword   = 0;
1350
1351         /* Clear consumer block for the same reason given above */
1352
1353         memset(bp->cons_block_virt, 0, sizeof(PI_CONSUMER_BLOCK));
1354
1355         /* Release all dynamically allocate skb in the receive ring. */
1356
1357         dfx_rcv_flush(bp);
1358
1359         /* Clear device structure flags */
1360
1361         netif_stop_queue(dev);
1362
1363         /* Deregister (free) IRQ */
1364
1365         free_irq(dev->irq, dev);
1366
1367         return(0);
1368 }
1369
1370
1371 /*
1372  * ======================
1373  * = dfx_int_pr_halt_id =
1374  * ======================
1375  *
1376  * Overview:
1377  *   Displays halt id's in string form.
1378  *
1379  * Returns:
1380  *   None
1381  *
1382  * Arguments:
1383  *   bp - pointer to board information
1384  *
1385  * Functional Description:
1386  *   Determine current halt id and display appropriate string.
1387  *
1388  * Return Codes:
1389  *   None
1390  *
1391  * Assumptions:
1392  *   None
1393  *
1394  * Side Effects:
1395  *   None
1396  */
1397
1398 static void dfx_int_pr_halt_id(DFX_board_t      *bp)
1399         {
1400         PI_UINT32       port_status;                    /* PDQ port status register value */
1401         PI_UINT32       halt_id;                                /* PDQ port status halt ID */
1402
1403         /* Read the latest port status */
1404
1405         dfx_port_read_long(bp, PI_PDQ_K_REG_PORT_STATUS, &port_status);
1406
1407         /* Display halt state transition information */
1408
1409         halt_id = (port_status & PI_PSTATUS_M_HALT_ID) >> PI_PSTATUS_V_HALT_ID;
1410         switch (halt_id)
1411                 {
1412                 case PI_HALT_ID_K_SELFTEST_TIMEOUT:
1413                         printk("%s: Halt ID: Selftest Timeout\n", bp->dev->name);
1414                         break;
1415
1416                 case PI_HALT_ID_K_PARITY_ERROR:
1417                         printk("%s: Halt ID: Host Bus Parity Error\n", bp->dev->name);
1418                         break;
1419
1420                 case PI_HALT_ID_K_HOST_DIR_HALT:
1421                         printk("%s: Halt ID: Host-Directed Halt\n", bp->dev->name);
1422                         break;
1423
1424                 case PI_HALT_ID_K_SW_FAULT:
1425                         printk("%s: Halt ID: Adapter Software Fault\n", bp->dev->name);
1426                         break;
1427
1428                 case PI_HALT_ID_K_HW_FAULT:
1429                         printk("%s: Halt ID: Adapter Hardware Fault\n", bp->dev->name);
1430                         break;
1431
1432                 case PI_HALT_ID_K_PC_TRACE:
1433                         printk("%s: Halt ID: FDDI Network PC Trace Path Test\n", bp->dev->name);
1434                         break;
1435
1436                 case PI_HALT_ID_K_DMA_ERROR:
1437                         printk("%s: Halt ID: Adapter DMA Error\n", bp->dev->name);
1438                         break;
1439
1440                 case PI_HALT_ID_K_IMAGE_CRC_ERROR:
1441                         printk("%s: Halt ID: Firmware Image CRC Error\n", bp->dev->name);
1442                         break;
1443
1444                 case PI_HALT_ID_K_BUS_EXCEPTION:
1445                         printk("%s: Halt ID: 68000 Bus Exception\n", bp->dev->name);
1446                         break;
1447
1448                 default:
1449                         printk("%s: Halt ID: Unknown (code = %X)\n", bp->dev->name, halt_id);
1450                         break;
1451                 }
1452         }
1453
1454
1455 /*
1456  * ==========================
1457  * = dfx_int_type_0_process =
1458  * ==========================
1459  *
1460  * Overview:
1461  *   Processes Type 0 interrupts.
1462  *
1463  * Returns:
1464  *   None
1465  *
1466  * Arguments:
1467  *   bp - pointer to board information
1468  *
1469  * Functional Description:
1470  *   Processes all enabled Type 0 interrupts.  If the reason for the interrupt
1471  *   is a serious fault on the adapter, then an error message is displayed
1472  *   and the adapter is reset.
1473  *
1474  *   One tricky potential timing window is the rapid succession of "link avail"
1475  *   "link unavail" state change interrupts.  The acknowledgement of the Type 0
1476  *   interrupt must be done before reading the state from the Port Status
1477  *   register.  This is true because a state change could occur after reading
1478  *   the data, but before acknowledging the interrupt.  If this state change
1479  *   does happen, it would be lost because the driver is using the old state,
1480  *   and it will never know about the new state because it subsequently
1481  *   acknowledges the state change interrupt.
1482  *
1483  *          INCORRECT                                      CORRECT
1484  *      read type 0 int reasons                   read type 0 int reasons
1485  *      read adapter state                        ack type 0 interrupts
1486  *      ack type 0 interrupts                     read adapter state
1487  *      ... process interrupt ...                 ... process interrupt ...
1488  *
1489  * Return Codes:
1490  *   None
1491  *
1492  * Assumptions:
1493  *   None
1494  *
1495  * Side Effects:
1496  *   An adapter reset may occur if the adapter has any Type 0 error interrupts
1497  *   or if the port status indicates that the adapter is halted.  The driver
1498  *   is responsible for reinitializing the adapter with the current CAM
1499  *   contents and adapter filter settings.
1500  */
1501
1502 static void dfx_int_type_0_process(DFX_board_t  *bp)
1503
1504         {
1505         PI_UINT32       type_0_status;          /* Host Interrupt Type 0 register */
1506         PI_UINT32       state;                          /* current adap state (from port status) */
1507
1508         /*
1509          * Read host interrupt Type 0 register to determine which Type 0
1510          * interrupts are pending.  Immediately write it back out to clear
1511          * those interrupts.
1512          */
1513
1514         dfx_port_read_long(bp, PI_PDQ_K_REG_TYPE_0_STATUS, &type_0_status);
1515         dfx_port_write_long(bp, PI_PDQ_K_REG_TYPE_0_STATUS, type_0_status);
1516
1517         /* Check for Type 0 error interrupts */
1518
1519         if (type_0_status & (PI_TYPE_0_STAT_M_NXM |
1520                                                         PI_TYPE_0_STAT_M_PM_PAR_ERR |
1521                                                         PI_TYPE_0_STAT_M_BUS_PAR_ERR))
1522                 {
1523                 /* Check for Non-Existent Memory error */
1524
1525                 if (type_0_status & PI_TYPE_0_STAT_M_NXM)
1526                         printk("%s: Non-Existent Memory Access Error\n", bp->dev->name);
1527
1528                 /* Check for Packet Memory Parity error */
1529
1530                 if (type_0_status & PI_TYPE_0_STAT_M_PM_PAR_ERR)
1531                         printk("%s: Packet Memory Parity Error\n", bp->dev->name);
1532
1533                 /* Check for Host Bus Parity error */
1534
1535                 if (type_0_status & PI_TYPE_0_STAT_M_BUS_PAR_ERR)
1536                         printk("%s: Host Bus Parity Error\n", bp->dev->name);
1537
1538                 /* Reset adapter and bring it back on-line */
1539
1540                 bp->link_available = PI_K_FALSE;        /* link is no longer available */
1541                 bp->reset_type = 0;                                     /* rerun on-board diagnostics */
1542                 printk("%s: Resetting adapter...\n", bp->dev->name);
1543                 if (dfx_adap_init(bp, 0) != DFX_K_SUCCESS)
1544                         {
1545                         printk("%s: Adapter reset failed!  Disabling adapter interrupts.\n", bp->dev->name);
1546                         dfx_port_write_long(bp, PI_PDQ_K_REG_HOST_INT_ENB, PI_HOST_INT_K_DISABLE_ALL_INTS);
1547                         return;
1548                         }
1549                 printk("%s: Adapter reset successful!\n", bp->dev->name);
1550                 return;
1551                 }
1552
1553         /* Check for transmit flush interrupt */
1554
1555         if (type_0_status & PI_TYPE_0_STAT_M_XMT_FLUSH)
1556                 {
1557                 /* Flush any pending xmt's and acknowledge the flush interrupt */
1558
1559                 bp->link_available = PI_K_FALSE;                /* link is no longer available */
1560                 dfx_xmt_flush(bp);                                              /* flush any outstanding packets */
1561                 (void) dfx_hw_port_ctrl_req(bp,
1562                                                                         PI_PCTRL_M_XMT_DATA_FLUSH_DONE,
1563                                                                         0,
1564                                                                         0,
1565                                                                         NULL);
1566                 }
1567
1568         /* Check for adapter state change */
1569
1570         if (type_0_status & PI_TYPE_0_STAT_M_STATE_CHANGE)
1571                 {
1572                 /* Get latest adapter state */
1573
1574                 state = dfx_hw_adap_state_rd(bp);       /* get adapter state */
1575                 if (state == PI_STATE_K_HALTED)
1576                         {
1577                         /*
1578                          * Adapter has transitioned to HALTED state, try to reset
1579                          * adapter to bring it back on-line.  If reset fails,
1580                          * leave the adapter in the broken state.
1581                          */
1582
1583                         printk("%s: Controller has transitioned to HALTED state!\n", bp->dev->name);
1584                         dfx_int_pr_halt_id(bp);                 /* display halt id as string */
1585
1586                         /* Reset adapter and bring it back on-line */
1587
1588                         bp->link_available = PI_K_FALSE;        /* link is no longer available */
1589                         bp->reset_type = 0;                                     /* rerun on-board diagnostics */
1590                         printk("%s: Resetting adapter...\n", bp->dev->name);
1591                         if (dfx_adap_init(bp, 0) != DFX_K_SUCCESS)
1592                                 {
1593                                 printk("%s: Adapter reset failed!  Disabling adapter interrupts.\n", bp->dev->name);
1594                                 dfx_port_write_long(bp, PI_PDQ_K_REG_HOST_INT_ENB, PI_HOST_INT_K_DISABLE_ALL_INTS);
1595                                 return;
1596                                 }
1597                         printk("%s: Adapter reset successful!\n", bp->dev->name);
1598                         }
1599                 else if (state == PI_STATE_K_LINK_AVAIL)
1600                         {
1601                         bp->link_available = PI_K_TRUE;         /* set link available flag */
1602                         }
1603                 }
1604         }
1605
1606
1607 /*
1608  * ==================
1609  * = dfx_int_common =
1610  * ==================
1611  *
1612  * Overview:
1613  *   Interrupt service routine (ISR)
1614  *
1615  * Returns:
1616  *   None
1617  *
1618  * Arguments:
1619  *   bp - pointer to board information
1620  *
1621  * Functional Description:
1622  *   This is the ISR which processes incoming adapter interrupts.
1623  *
1624  * Return Codes:
1625  *   None
1626  *
1627  * Assumptions:
1628  *   This routine assumes PDQ interrupts have not been disabled.
1629  *   When interrupts are disabled at the PDQ, the Port Status register
1630  *   is automatically cleared.  This routine uses the Port Status
1631  *   register value to determine whether a Type 0 interrupt occurred,
1632  *   so it's important that adapter interrupts are not normally
1633  *   enabled/disabled at the PDQ.
1634  *
1635  *   It's vital that this routine is NOT reentered for the
1636  *   same board and that the OS is not in another section of
1637  *   code (eg. dfx_xmt_queue_pkt) for the same board on a
1638  *   different thread.
1639  *
1640  * Side Effects:
1641  *   Pending interrupts are serviced.  Depending on the type of
1642  *   interrupt, acknowledging and clearing the interrupt at the
1643  *   PDQ involves writing a register to clear the interrupt bit
1644  *   or updating completion indices.
1645  */
1646
1647 static void dfx_int_common(struct net_device *dev)
1648 {
1649         DFX_board_t     *bp = dev->priv;
1650         PI_UINT32       port_status;            /* Port Status register */
1651
1652         /* Process xmt interrupts - frequent case, so always call this routine */
1653
1654         if(dfx_xmt_done(bp))                            /* free consumed xmt packets */
1655                 netif_wake_queue(dev);
1656
1657         /* Process rcv interrupts - frequent case, so always call this routine */
1658
1659         dfx_rcv_queue_process(bp);              /* service received LLC frames */
1660
1661         /*
1662          * Transmit and receive producer and completion indices are updated on the
1663          * adapter by writing to the Type 2 Producer register.  Since the frequent
1664          * case is that we'll be processing either LLC transmit or receive buffers,
1665          * we'll optimize I/O writes by doing a single register write here.
1666          */
1667
1668         dfx_port_write_long(bp, PI_PDQ_K_REG_TYPE_2_PROD, bp->rcv_xmt_reg.lword);
1669
1670         /* Read PDQ Port Status register to find out which interrupts need processing */
1671
1672         dfx_port_read_long(bp, PI_PDQ_K_REG_PORT_STATUS, &port_status);
1673
1674         /* Process Type 0 interrupts (if any) - infrequent, so only call when needed */
1675
1676         if (port_status & PI_PSTATUS_M_TYPE_0_PENDING)
1677                 dfx_int_type_0_process(bp);     /* process Type 0 interrupts */
1678         }
1679
1680
1681 /*
1682  * =================
1683  * = dfx_interrupt =
1684  * =================
1685  *
1686  * Overview:
1687  *   Interrupt processing routine
1688  *
1689  * Returns:
1690  *   Whether a valid interrupt was seen.
1691  *
1692  * Arguments:
1693  *   irq        - interrupt vector
1694  *   dev_id     - pointer to device information
1695  *
1696  * Functional Description:
1697  *   This routine calls the interrupt processing routine for this adapter.  It
1698  *   disables and reenables adapter interrupts, as appropriate.  We can support
1699  *   shared interrupts since the incoming dev_id pointer provides our device
1700  *   structure context.
1701  *
1702  * Return Codes:
1703  *   IRQ_HANDLED - an IRQ was handled.
1704  *   IRQ_NONE    - no IRQ was handled.
1705  *
1706  * Assumptions:
1707  *   The interrupt acknowledgement at the hardware level (eg. ACKing the PIC
1708  *   on Intel-based systems) is done by the operating system outside this
1709  *   routine.
1710  *
1711  *       System interrupts are enabled through this call.
1712  *
1713  * Side Effects:
1714  *   Interrupts are disabled, then reenabled at the adapter.
1715  */
1716
1717 static irqreturn_t dfx_interrupt(int irq, void *dev_id)
1718 {
1719         struct net_device       *dev = dev_id;
1720         DFX_board_t             *bp;    /* private board structure pointer */
1721
1722         /* Get board pointer only if device structure is valid */
1723
1724         bp = dev->priv;
1725
1726         /* See if we're already servicing an interrupt */
1727
1728         /* Service adapter interrupts */
1729
1730         if (bp->bus_type == DFX_BUS_TYPE_PCI) {
1731                 u32 status;
1732
1733                 dfx_port_read_long(bp, PFI_K_REG_STATUS, &status);
1734                 if (!(status & PFI_STATUS_M_PDQ_INT))
1735                         return IRQ_NONE;
1736
1737                 spin_lock(&bp->lock);
1738
1739                 /* Disable PDQ-PFI interrupts at PFI */
1740                 dfx_port_write_long(bp, PFI_K_REG_MODE_CTRL,
1741                                     PFI_MODE_M_DMA_ENB);
1742
1743                 /* Call interrupt service routine for this adapter */
1744                 dfx_int_common(dev);
1745
1746                 /* Clear PDQ interrupt status bit and reenable interrupts */
1747                 dfx_port_write_long(bp, PFI_K_REG_STATUS,
1748                                     PFI_STATUS_M_PDQ_INT);
1749                 dfx_port_write_long(bp, PFI_K_REG_MODE_CTRL,
1750                                     (PFI_MODE_M_PDQ_INT_ENB |
1751                                      PFI_MODE_M_DMA_ENB));
1752
1753                 spin_unlock(&bp->lock);
1754         } else {
1755                 u8 status;
1756
1757                 dfx_port_read_byte(bp, PI_ESIC_K_IO_CONFIG_STAT_0, &status);
1758                 if (!(status & PI_CONFIG_STAT_0_M_PEND))
1759                         return IRQ_NONE;
1760
1761                 spin_lock(&bp->lock);
1762
1763                 /* Disable interrupts at the ESIC */
1764                 status &= ~PI_CONFIG_STAT_0_M_INT_ENB;
1765                 dfx_port_write_byte(bp, PI_ESIC_K_IO_CONFIG_STAT_0, status);
1766
1767                 /* Call interrupt service routine for this adapter */
1768                 dfx_int_common(dev);
1769
1770                 /* Reenable interrupts at the ESIC */
1771                 dfx_port_read_byte(bp, PI_ESIC_K_IO_CONFIG_STAT_0, &status);
1772                 status |= PI_CONFIG_STAT_0_M_INT_ENB;
1773                 dfx_port_write_byte(bp, PI_ESIC_K_IO_CONFIG_STAT_0, status);
1774
1775                 spin_unlock(&bp->lock);
1776         }
1777
1778         return IRQ_HANDLED;
1779 }
1780
1781
1782 /*
1783  * =====================
1784  * = dfx_ctl_get_stats =
1785  * =====================
1786  *
1787  * Overview:
1788  *   Get statistics for FDDI adapter
1789  *
1790  * Returns:
1791  *   Pointer to FDDI statistics structure
1792  *
1793  * Arguments:
1794  *   dev - pointer to device information
1795  *
1796  * Functional Description:
1797  *   Gets current MIB objects from adapter, then
1798  *   returns FDDI statistics structure as defined
1799  *   in if_fddi.h.
1800  *
1801  *   Note: Since the FDDI statistics structure is
1802  *   still new and the device structure doesn't
1803  *   have an FDDI-specific get statistics handler,
1804  *   we'll return the FDDI statistics structure as
1805  *   a pointer to an Ethernet statistics structure.
1806  *   That way, at least the first part of the statistics
1807  *   structure can be decoded properly, and it allows
1808  *   "smart" applications to perform a second cast to
1809  *   decode the FDDI-specific statistics.
1810  *
1811  *   We'll have to pay attention to this routine as the
1812  *   device structure becomes more mature and LAN media
1813  *   independent.
1814  *
1815  * Return Codes:
1816  *   None
1817  *
1818  * Assumptions:
1819  *   None
1820  *
1821  * Side Effects:
1822  *   None
1823  */
1824
1825 static struct net_device_stats *dfx_ctl_get_stats(struct net_device *dev)
1826         {
1827         DFX_board_t     *bp = dev->priv;
1828
1829         /* Fill the bp->stats structure with driver-maintained counters */
1830
1831         bp->stats.gen.rx_packets = bp->rcv_total_frames;
1832         bp->stats.gen.tx_packets = bp->xmt_total_frames;
1833         bp->stats.gen.rx_bytes   = bp->rcv_total_bytes;
1834         bp->stats.gen.tx_bytes   = bp->xmt_total_bytes;
1835         bp->stats.gen.rx_errors  = bp->rcv_crc_errors +
1836                                    bp->rcv_frame_status_errors +
1837                                    bp->rcv_length_errors;
1838         bp->stats.gen.tx_errors  = bp->xmt_length_errors;
1839         bp->stats.gen.rx_dropped = bp->rcv_discards;
1840         bp->stats.gen.tx_dropped = bp->xmt_discards;
1841         bp->stats.gen.multicast  = bp->rcv_multicast_frames;
1842         bp->stats.gen.collisions = 0;           /* always zero (0) for FDDI */
1843
1844         /* Get FDDI SMT MIB objects */
1845
1846         bp->cmd_req_virt->cmd_type = PI_CMD_K_SMT_MIB_GET;
1847         if (dfx_hw_dma_cmd_req(bp) != DFX_K_SUCCESS)
1848                 return((struct net_device_stats *) &bp->stats);
1849
1850         /* Fill the bp->stats structure with the SMT MIB object values */
1851
1852         memcpy(bp->stats.smt_station_id, &bp->cmd_rsp_virt->smt_mib_get.smt_station_id, sizeof(bp->cmd_rsp_virt->smt_mib_get.smt_station_id));
1853         bp->stats.smt_op_version_id                                     = bp->cmd_rsp_virt->smt_mib_get.smt_op_version_id;
1854         bp->stats.smt_hi_version_id                                     = bp->cmd_rsp_virt->smt_mib_get.smt_hi_version_id;
1855         bp->stats.smt_lo_version_id                                     = bp->cmd_rsp_virt->smt_mib_get.smt_lo_version_id;
1856         memcpy(bp->stats.smt_user_data, &bp->cmd_rsp_virt->smt_mib_get.smt_user_data, sizeof(bp->cmd_rsp_virt->smt_mib_get.smt_user_data));
1857         bp->stats.smt_mib_version_id                            = bp->cmd_rsp_virt->smt_mib_get.smt_mib_version_id;
1858         bp->stats.smt_mac_cts                                           = bp->cmd_rsp_virt->smt_mib_get.smt_mac_ct;
1859         bp->stats.smt_non_master_cts                            = bp->cmd_rsp_virt->smt_mib_get.smt_non_master_ct;
1860         bp->stats.smt_master_cts                                        = bp->cmd_rsp_virt->smt_mib_get.smt_master_ct;
1861         bp->stats.smt_available_paths                           = bp->cmd_rsp_virt->smt_mib_get.smt_available_paths;
1862         bp->stats.smt_config_capabilities                       = bp->cmd_rsp_virt->smt_mib_get.smt_config_capabilities;
1863         bp->stats.smt_config_policy                                     = bp->cmd_rsp_virt->smt_mib_get.smt_config_policy;
1864         bp->stats.smt_connection_policy                         = bp->cmd_rsp_virt->smt_mib_get.smt_connection_policy;
1865         bp->stats.smt_t_notify                                          = bp->cmd_rsp_virt->smt_mib_get.smt_t_notify;
1866         bp->stats.smt_stat_rpt_policy                           = bp->cmd_rsp_virt->smt_mib_get.smt_stat_rpt_policy;
1867         bp->stats.smt_trace_max_expiration                      = bp->cmd_rsp_virt->smt_mib_get.smt_trace_max_expiration;
1868         bp->stats.smt_bypass_present                            = bp->cmd_rsp_virt->smt_mib_get.smt_bypass_present;
1869         bp->stats.smt_ecm_state                                         = bp->cmd_rsp_virt->smt_mib_get.smt_ecm_state;
1870         bp->stats.smt_cf_state                                          = bp->cmd_rsp_virt->smt_mib_get.smt_cf_state;
1871         bp->stats.smt_remote_disconnect_flag            = bp->cmd_rsp_virt->smt_mib_get.smt_remote_disconnect_flag;
1872         bp->stats.smt_station_status                            = bp->cmd_rsp_virt->smt_mib_get.smt_station_status;
1873         bp->stats.smt_peer_wrap_flag                            = bp->cmd_rsp_virt->smt_mib_get.smt_peer_wrap_flag;
1874         bp->stats.smt_time_stamp                                        = bp->cmd_rsp_virt->smt_mib_get.smt_msg_time_stamp.ls;
1875         bp->stats.smt_transition_time_stamp                     = bp->cmd_rsp_virt->smt_mib_get.smt_transition_time_stamp.ls;
1876         bp->stats.mac_frame_status_functions            = bp->cmd_rsp_virt->smt_mib_get.mac_frame_status_functions;
1877         bp->stats.mac_t_max_capability                          = bp->cmd_rsp_virt->smt_mib_get.mac_t_max_capability;
1878         bp->stats.mac_tvx_capability                            = bp->cmd_rsp_virt->smt_mib_get.mac_tvx_capability;
1879         bp->stats.mac_available_paths                           = bp->cmd_rsp_virt->smt_mib_get.mac_available_paths;
1880         bp->stats.mac_current_path                                      = bp->cmd_rsp_virt->smt_mib_get.mac_current_path;
1881         memcpy(bp->stats.mac_upstream_nbr, &bp->cmd_rsp_virt->smt_mib_get.mac_upstream_nbr, FDDI_K_ALEN);
1882         memcpy(bp->stats.mac_downstream_nbr, &bp->cmd_rsp_virt->smt_mib_get.mac_downstream_nbr, FDDI_K_ALEN);
1883         memcpy(bp->stats.mac_old_upstream_nbr, &bp->cmd_rsp_virt->smt_mib_get.mac_old_upstream_nbr, FDDI_K_ALEN);
1884         memcpy(bp->stats.mac_old_downstream_nbr, &bp->cmd_rsp_virt->smt_mib_get.mac_old_downstream_nbr, FDDI_K_ALEN);
1885         bp->stats.mac_dup_address_test                          = bp->cmd_rsp_virt->smt_mib_get.mac_dup_address_test;
1886         bp->stats.mac_requested_paths                           = bp->cmd_rsp_virt->smt_mib_get.mac_requested_paths;
1887         bp->stats.mac_downstream_port_type                      = bp->cmd_rsp_virt->smt_mib_get.mac_downstream_port_type;
1888         memcpy(bp->stats.mac_smt_address, &bp->cmd_rsp_virt->smt_mib_get.mac_smt_address, FDDI_K_ALEN);
1889         bp->stats.mac_t_req                                                     = bp->cmd_rsp_virt->smt_mib_get.mac_t_req;
1890         bp->stats.mac_t_neg                                                     = bp->cmd_rsp_virt->smt_mib_get.mac_t_neg;
1891         bp->stats.mac_t_max                                                     = bp->cmd_rsp_virt->smt_mib_get.mac_t_max;
1892         bp->stats.mac_tvx_value                                         = bp->cmd_rsp_virt->smt_mib_get.mac_tvx_value;
1893         bp->stats.mac_frame_error_threshold                     = bp->cmd_rsp_virt->smt_mib_get.mac_frame_error_threshold;
1894         bp->stats.mac_frame_error_ratio                         = bp->cmd_rsp_virt->smt_mib_get.mac_frame_error_ratio;
1895         bp->stats.mac_rmt_state                                         = bp->cmd_rsp_virt->smt_mib_get.mac_rmt_state;
1896         bp->stats.mac_da_flag                                           = bp->cmd_rsp_virt->smt_mib_get.mac_da_flag;
1897         bp->stats.mac_una_da_flag                                       = bp->cmd_rsp_virt->smt_mib_get.mac_unda_flag;
1898         bp->stats.mac_frame_error_flag                          = bp->cmd_rsp_virt->smt_mib_get.mac_frame_error_flag;
1899         bp->stats.mac_ma_unitdata_available                     = bp->cmd_rsp_virt->smt_mib_get.mac_ma_unitdata_available;
1900         bp->stats.mac_hardware_present                          = bp->cmd_rsp_virt->smt_mib_get.mac_hardware_present;
1901         bp->stats.mac_ma_unitdata_enable                        = bp->cmd_rsp_virt->smt_mib_get.mac_ma_unitdata_enable;
1902         bp->stats.path_tvx_lower_bound                          = bp->cmd_rsp_virt->smt_mib_get.path_tvx_lower_bound;
1903         bp->stats.path_t_max_lower_bound                        = bp->cmd_rsp_virt->smt_mib_get.path_t_max_lower_bound;
1904         bp->stats.path_max_t_req                                        = bp->cmd_rsp_virt->smt_mib_get.path_max_t_req;
1905         memcpy(bp->stats.path_configuration, &bp->cmd_rsp_virt->smt_mib_get.path_configuration, sizeof(bp->cmd_rsp_virt->smt_mib_get.path_configuration));
1906         bp->stats.port_my_type[0]                                       = bp->cmd_rsp_virt->smt_mib_get.port_my_type[0];
1907         bp->stats.port_my_type[1]                                       = bp->cmd_rsp_virt->smt_mib_get.port_my_type[1];
1908         bp->stats.port_neighbor_type[0]                         = bp->cmd_rsp_virt->smt_mib_get.port_neighbor_type[0];
1909         bp->stats.port_neighbor_type[1]                         = bp->cmd_rsp_virt->smt_mib_get.port_neighbor_type[1];
1910         bp->stats.port_connection_policies[0]           = bp->cmd_rsp_virt->smt_mib_get.port_connection_policies[0];
1911         bp->stats.port_connection_policies[1]           = bp->cmd_rsp_virt->smt_mib_get.port_connection_policies[1];
1912         bp->stats.port_mac_indicated[0]                         = bp->cmd_rsp_virt->smt_mib_get.port_mac_indicated[0];
1913         bp->stats.port_mac_indicated[1]                         = bp->cmd_rsp_virt->smt_mib_get.port_mac_indicated[1];
1914         bp->stats.port_current_path[0]                          = bp->cmd_rsp_virt->smt_mib_get.port_current_path[0];
1915         bp->stats.port_current_path[1]                          = bp->cmd_rsp_virt->smt_mib_get.port_current_path[1];
1916         memcpy(&bp->stats.port_requested_paths[0*3], &bp->cmd_rsp_virt->smt_mib_get.port_requested_paths[0], 3);
1917         memcpy(&bp->stats.port_requested_paths[1*3], &bp->cmd_rsp_virt->smt_mib_get.port_requested_paths[1], 3);
1918         bp->stats.port_mac_placement[0]                         = bp->cmd_rsp_virt->smt_mib_get.port_mac_placement[0];
1919         bp->stats.port_mac_placement[1]                         = bp->cmd_rsp_virt->smt_mib_get.port_mac_placement[1];
1920         bp->stats.port_available_paths[0]                       = bp->cmd_rsp_virt->smt_mib_get.port_available_paths[0];
1921         bp->stats.port_available_paths[1]                       = bp->cmd_rsp_virt->smt_mib_get.port_available_paths[1];
1922         bp->stats.port_pmd_class[0]                                     = bp->cmd_rsp_virt->smt_mib_get.port_pmd_class[0];
1923         bp->stats.port_pmd_class[1]                                     = bp->cmd_rsp_virt->smt_mib_get.port_pmd_class[1];
1924         bp->stats.port_connection_capabilities[0]       = bp->cmd_rsp_virt->smt_mib_get.port_connection_capabilities[0];
1925         bp->stats.port_connection_capabilities[1]       = bp->cmd_rsp_virt->smt_mib_get.port_connection_capabilities[1];
1926         bp->stats.port_bs_flag[0]                                       = bp->cmd_rsp_virt->smt_mib_get.port_bs_flag[0];
1927         bp->stats.port_bs_flag[1]                                       = bp->cmd_rsp_virt->smt_mib_get.port_bs_flag[1];
1928         bp->stats.port_ler_estimate[0]                          = bp->cmd_rsp_virt->smt_mib_get.port_ler_estimate[0];
1929         bp->stats.port_ler_estimate[1]                          = bp->cmd_rsp_virt->smt_mib_get.port_ler_estimate[1];
1930         bp->stats.port_ler_cutoff[0]                            = bp->cmd_rsp_virt->smt_mib_get.port_ler_cutoff[0];
1931         bp->stats.port_ler_cutoff[1]                            = bp->cmd_rsp_virt->smt_mib_get.port_ler_cutoff[1];
1932         bp->stats.port_ler_alarm[0]                                     = bp->cmd_rsp_virt->smt_mib_get.port_ler_alarm[0];
1933         bp->stats.port_ler_alarm[1]                                     = bp->cmd_rsp_virt->smt_mib_get.port_ler_alarm[1];
1934         bp->stats.port_connect_state[0]                         = bp->cmd_rsp_virt->smt_mib_get.port_connect_state[0];
1935         bp->stats.port_connect_state[1]                         = bp->cmd_rsp_virt->smt_mib_get.port_connect_state[1];
1936         bp->stats.port_pcm_state[0]                                     = bp->cmd_rsp_virt->smt_mib_get.port_pcm_state[0];
1937         bp->stats.port_pcm_state[1]                                     = bp->cmd_rsp_virt->smt_mib_get.port_pcm_state[1];
1938         bp->stats.port_pc_withhold[0]                           = bp->cmd_rsp_virt->smt_mib_get.port_pc_withhold[0];
1939         bp->stats.port_pc_withhold[1]                           = bp->cmd_rsp_virt->smt_mib_get.port_pc_withhold[1];
1940         bp->stats.port_ler_flag[0]                                      = bp->cmd_rsp_virt->smt_mib_get.port_ler_flag[0];
1941         bp->stats.port_ler_flag[1]                                      = bp->cmd_rsp_virt->smt_mib_get.port_ler_flag[1];
1942         bp->stats.port_hardware_present[0]                      = bp->cmd_rsp_virt->smt_mib_get.port_hardware_present[0];
1943         bp->stats.port_hardware_present[1]                      = bp->cmd_rsp_virt->smt_mib_get.port_hardware_present[1];
1944
1945         /* Get FDDI counters */
1946
1947         bp->cmd_req_virt->cmd_type = PI_CMD_K_CNTRS_GET;
1948         if (dfx_hw_dma_cmd_req(bp) != DFX_K_SUCCESS)
1949                 return((struct net_device_stats *) &bp->stats);
1950
1951         /* Fill the bp->stats structure with the FDDI counter values */
1952
1953         bp->stats.mac_frame_cts                         = bp->cmd_rsp_virt->cntrs_get.cntrs.frame_cnt.ls;
1954         bp->stats.mac_copied_cts                        = bp->cmd_rsp_virt->cntrs_get.cntrs.copied_cnt.ls;
1955         bp->stats.mac_transmit_cts                      = bp->cmd_rsp_virt->cntrs_get.cntrs.transmit_cnt.ls;
1956         bp->stats.mac_error_cts                         = bp->cmd_rsp_virt->cntrs_get.cntrs.error_cnt.ls;
1957         bp->stats.mac_lost_cts                          = bp->cmd_rsp_virt->cntrs_get.cntrs.lost_cnt.ls;
1958         bp->stats.port_lct_fail_cts[0]          = bp->cmd_rsp_virt->cntrs_get.cntrs.lct_rejects[0].ls;
1959         bp->stats.port_lct_fail_cts[1]          = bp->cmd_rsp_virt->cntrs_get.cntrs.lct_rejects[1].ls;
1960         bp->stats.port_lem_reject_cts[0]        = bp->cmd_rsp_virt->cntrs_get.cntrs.lem_rejects[0].ls;
1961         bp->stats.port_lem_reject_cts[1]        = bp->cmd_rsp_virt->cntrs_get.cntrs.lem_rejects[1].ls;
1962         bp->stats.port_lem_cts[0]                       = bp->cmd_rsp_virt->cntrs_get.cntrs.link_errors[0].ls;
1963         bp->stats.port_lem_cts[1]                       = bp->cmd_rsp_virt->cntrs_get.cntrs.link_errors[1].ls;
1964
1965         return((struct net_device_stats *) &bp->stats);
1966         }
1967
1968
1969 /*
1970  * ==============================
1971  * = dfx_ctl_set_multicast_list =
1972  * ==============================
1973  *
1974  * Overview:
1975  *   Enable/Disable LLC frame promiscuous mode reception
1976  *   on the adapter and/or update multicast address table.
1977  *
1978  * Returns:
1979  *   None
1980  *
1981  * Arguments:
1982  *   dev - pointer to device information
1983  *
1984  * Functional Description:
1985  *   This routine follows a fairly simple algorithm for setting the
1986  *   adapter filters and CAM:
1987  *
1988  *              if IFF_PROMISC flag is set
1989  *                      enable LLC individual/group promiscuous mode
1990  *              else
1991  *                      disable LLC individual/group promiscuous mode
1992  *                      if number of incoming multicast addresses >
1993  *                                      (CAM max size - number of unicast addresses in CAM)
1994  *                              enable LLC group promiscuous mode
1995  *                              set driver-maintained multicast address count to zero
1996  *                      else
1997  *                              disable LLC group promiscuous mode
1998  *                              set driver-maintained multicast address count to incoming count
1999  *                      update adapter CAM
2000  *              update adapter filters
2001  *
2002  * Return Codes:
2003  *   None
2004  *
2005  * Assumptions:
2006  *   Multicast addresses are presented in canonical (LSB) format.
2007  *
2008  * Side Effects:
2009  *   On-board adapter CAM and filters are updated.
2010  */
2011
2012 static void dfx_ctl_set_multicast_list(struct net_device *dev)
2013         {
2014         DFX_board_t                     *bp = dev->priv;
2015         int                                     i;                      /* used as index in for loop */
2016         struct dev_mc_list      *dmi;           /* ptr to multicast addr entry */
2017
2018         /* Enable LLC frame promiscuous mode, if necessary */
2019
2020         if (dev->flags & IFF_PROMISC)
2021                 bp->ind_group_prom = PI_FSTATE_K_PASS;          /* Enable LLC ind/group prom mode */
2022
2023         /* Else, update multicast address table */
2024
2025         else
2026                 {
2027                 bp->ind_group_prom = PI_FSTATE_K_BLOCK;         /* Disable LLC ind/group prom mode */
2028                 /*
2029                  * Check whether incoming multicast address count exceeds table size
2030                  *
2031                  * Note: The adapters utilize an on-board 64 entry CAM for
2032                  *       supporting perfect filtering of multicast packets
2033                  *               and bridge functions when adding unicast addresses.
2034                  *               There is no hash function available.  To support
2035                  *               additional multicast addresses, the all multicast
2036                  *               filter (LLC group promiscuous mode) must be enabled.
2037                  *
2038                  *               The firmware reserves two CAM entries for SMT-related
2039                  *               multicast addresses, which leaves 62 entries available.
2040                  *               The following code ensures that we're not being asked
2041                  *               to add more than 62 addresses to the CAM.  If we are,
2042                  *               the driver will enable the all multicast filter.
2043                  *               Should the number of multicast addresses drop below
2044                  *               the high water mark, the filter will be disabled and
2045                  *               perfect filtering will be used.
2046                  */
2047
2048                 if (dev->mc_count > (PI_CMD_ADDR_FILTER_K_SIZE - bp->uc_count))
2049                         {
2050                         bp->group_prom  = PI_FSTATE_K_PASS;             /* Enable LLC group prom mode */
2051                         bp->mc_count    = 0;                                    /* Don't add mc addrs to CAM */
2052                         }
2053                 else
2054                         {
2055                         bp->group_prom  = PI_FSTATE_K_BLOCK;    /* Disable LLC group prom mode */
2056                         bp->mc_count    = dev->mc_count;                /* Add mc addrs to CAM */
2057                         }
2058
2059                 /* Copy addresses to multicast address table, then update adapter CAM */
2060
2061                 dmi = dev->mc_list;                             /* point to first multicast addr */
2062                 for (i=0; i < bp->mc_count; i++)
2063                         {
2064                         memcpy(&bp->mc_table[i*FDDI_K_ALEN], dmi->dmi_addr, FDDI_K_ALEN);
2065                         dmi = dmi->next;                        /* point to next multicast addr */
2066                         }
2067                 if (dfx_ctl_update_cam(bp) != DFX_K_SUCCESS)
2068                         {
2069                         DBG_printk("%s: Could not update multicast address table!\n", dev->name);
2070                         }
2071                 else
2072                         {
2073                         DBG_printk("%s: Multicast address table updated!  Added %d addresses.\n", dev->name, bp->mc_count);
2074                         }
2075                 }
2076
2077         /* Update adapter filters */
2078
2079         if (dfx_ctl_update_filters(bp) != DFX_K_SUCCESS)
2080                 {
2081                 DBG_printk("%s: Could not update adapter filters!\n", dev->name);
2082                 }
2083         else
2084                 {
2085                 DBG_printk("%s: Adapter filters updated!\n", dev->name);
2086                 }
2087         }
2088
2089
2090 /*
2091  * ===========================
2092  * = dfx_ctl_set_mac_address =
2093  * ===========================
2094  *
2095  * Overview:
2096  *   Add node address override (unicast address) to adapter
2097  *   CAM and update dev_addr field in device table.
2098  *
2099  * Returns:
2100  *   None
2101  *
2102  * Arguments:
2103  *   dev  - pointer to device information
2104  *   addr - pointer to sockaddr structure containing unicast address to add
2105  *
2106  * Functional Description:
2107  *   The adapter supports node address overrides by adding one or more
2108  *   unicast addresses to the adapter CAM.  This is similar to adding
2109  *   multicast addresses.  In this routine we'll update the driver and
2110  *   device structures with the new address, then update the adapter CAM
2111  *   to ensure that the adapter will copy and strip frames destined and
2112  *   sourced by that address.
2113  *
2114  * Return Codes:
2115  *   Always returns zero.
2116  *
2117  * Assumptions:
2118  *   The address pointed to by addr->sa_data is a valid unicast
2119  *   address and is presented in canonical (LSB) format.
2120  *
2121  * Side Effects:
2122  *   On-board adapter CAM is updated.  On-board adapter filters
2123  *   may be updated.
2124  */
2125
2126 static int dfx_ctl_set_mac_address(struct net_device *dev, void *addr)
2127         {
2128         DFX_board_t             *bp = dev->priv;
2129         struct sockaddr *p_sockaddr = (struct sockaddr *)addr;
2130
2131         /* Copy unicast address to driver-maintained structs and update count */
2132
2133         memcpy(dev->dev_addr, p_sockaddr->sa_data, FDDI_K_ALEN);        /* update device struct */
2134         memcpy(&bp->uc_table[0], p_sockaddr->sa_data, FDDI_K_ALEN);     /* update driver struct */
2135         bp->uc_count = 1;
2136
2137         /*
2138          * Verify we're not exceeding the CAM size by adding unicast address
2139          *
2140          * Note: It's possible that before entering this routine we've
2141          *       already filled the CAM with 62 multicast addresses.
2142          *               Since we need to place the node address override into
2143          *               the CAM, we have to check to see that we're not
2144          *               exceeding the CAM size.  If we are, we have to enable
2145          *               the LLC group (multicast) promiscuous mode filter as
2146          *               in dfx_ctl_set_multicast_list.
2147          */
2148
2149         if ((bp->uc_count + bp->mc_count) > PI_CMD_ADDR_FILTER_K_SIZE)
2150                 {
2151                 bp->group_prom  = PI_FSTATE_K_PASS;             /* Enable LLC group prom mode */
2152                 bp->mc_count    = 0;                                    /* Don't add mc addrs to CAM */
2153
2154                 /* Update adapter filters */
2155
2156                 if (dfx_ctl_update_filters(bp) != DFX_K_SUCCESS)
2157                         {
2158                         DBG_printk("%s: Could not update adapter filters!\n", dev->name);
2159                         }
2160                 else
2161                         {
2162                         DBG_printk("%s: Adapter filters updated!\n", dev->name);
2163                         }
2164                 }
2165
2166         /* Update adapter CAM with new unicast address */
2167
2168         if (dfx_ctl_update_cam(bp) != DFX_K_SUCCESS)
2169                 {
2170                 DBG_printk("%s: Could not set new MAC address!\n", dev->name);
2171                 }
2172         else
2173                 {
2174                 DBG_printk("%s: Adapter CAM updated with new MAC address\n", dev->name);
2175                 }
2176         return(0);                      /* always return zero */
2177         }
2178
2179
2180 /*
2181  * ======================
2182  * = dfx_ctl_update_cam =
2183  * ======================
2184  *
2185  * Overview:
2186  *   Procedure to update adapter CAM (Content Addressable Memory)
2187  *   with desired unicast and multicast address entries.
2188  *
2189  * Returns:
2190  *   Condition code
2191  *
2192  * Arguments:
2193  *   bp - pointer to board information
2194  *
2195  * Functional Description:
2196  *   Updates adapter CAM with current contents of board structure
2197  *   unicast and multicast address tables.  Since there are only 62
2198  *   free entries in CAM, this routine ensures that the command
2199  *   request buffer is not overrun.
2200  *
2201  * Return Codes:
2202  *   DFX_K_SUCCESS - Request succeeded
2203  *   DFX_K_FAILURE - Request failed
2204  *
2205  * Assumptions:
2206  *   All addresses being added (unicast and multicast) are in canonical
2207  *   order.
2208  *
2209  * Side Effects:
2210  *   On-board adapter CAM is updated.
2211  */
2212
2213 static int dfx_ctl_update_cam(DFX_board_t *bp)
2214         {
2215         int                     i;                              /* used as index */
2216         PI_LAN_ADDR     *p_addr;                /* pointer to CAM entry */
2217
2218         /*
2219          * Fill in command request information
2220          *
2221          * Note: Even though both the unicast and multicast address
2222          *       table entries are stored as contiguous 6 byte entries,
2223          *               the firmware address filter set command expects each
2224          *               entry to be two longwords (8 bytes total).  We must be
2225          *               careful to only copy the six bytes of each unicast and
2226          *               multicast table entry into each command entry.  This
2227          *               is also why we must first clear the entire command
2228          *               request buffer.
2229          */
2230
2231         memset(bp->cmd_req_virt, 0, PI_CMD_REQ_K_SIZE_MAX);     /* first clear buffer */
2232         bp->cmd_req_virt->cmd_type = PI_CMD_K_ADDR_FILTER_SET;
2233         p_addr = &bp->cmd_req_virt->addr_filter_set.entry[0];
2234
2235         /* Now add unicast addresses to command request buffer, if any */
2236
2237         for (i=0; i < (int)bp->uc_count; i++)
2238                 {
2239                 if (i < PI_CMD_ADDR_FILTER_K_SIZE)
2240                         {
2241                         memcpy(p_addr, &bp->uc_table[i*FDDI_K_ALEN], FDDI_K_ALEN);
2242                         p_addr++;                       /* point to next command entry */
2243                         }
2244                 }
2245
2246         /* Now add multicast addresses to command request buffer, if any */
2247
2248         for (i=0; i < (int)bp->mc_count; i++)
2249                 {
2250                 if ((i + bp->uc_count) < PI_CMD_ADDR_FILTER_K_SIZE)
2251                         {
2252                         memcpy(p_addr, &bp->mc_table[i*FDDI_K_ALEN], FDDI_K_ALEN);
2253                         p_addr++;                       /* point to next command entry */
2254                         }
2255                 }
2256
2257         /* Issue command to update adapter CAM, then return */
2258
2259         if (dfx_hw_dma_cmd_req(bp) != DFX_K_SUCCESS)
2260                 return(DFX_K_FAILURE);
2261         return(DFX_K_SUCCESS);
2262         }
2263
2264
2265 /*
2266  * ==========================
2267  * = dfx_ctl_update_filters =
2268  * ==========================
2269  *
2270  * Overview:
2271  *   Procedure to update adapter filters with desired
2272  *   filter settings.
2273  *
2274  * Returns:
2275  *   Condition code
2276  *
2277  * Arguments:
2278  *   bp - pointer to board information
2279  *
2280  * Functional Description:
2281  *   Enables or disables filter using current filter settings.
2282  *
2283  * Return Codes:
2284  *   DFX_K_SUCCESS - Request succeeded.
2285  *   DFX_K_FAILURE - Request failed.
2286  *
2287  * Assumptions:
2288  *   We must always pass up packets destined to the broadcast
2289  *   address (FF-FF-FF-FF-FF-FF), so we'll always keep the
2290  *   broadcast filter enabled.
2291  *
2292  * Side Effects:
2293  *   On-board adapter filters are updated.
2294  */
2295
2296 static int dfx_ctl_update_filters(DFX_board_t *bp)
2297         {
2298         int     i = 0;                                  /* used as index */
2299
2300         /* Fill in command request information */
2301
2302         bp->cmd_req_virt->cmd_type = PI_CMD_K_FILTERS_SET;
2303
2304         /* Initialize Broadcast filter - * ALWAYS ENABLED * */
2305
2306         bp->cmd_req_virt->filter_set.item[i].item_code  = PI_ITEM_K_BROADCAST;
2307         bp->cmd_req_virt->filter_set.item[i++].value    = PI_FSTATE_K_PASS;
2308
2309         /* Initialize LLC Individual/Group Promiscuous filter */
2310
2311         bp->cmd_req_virt->filter_set.item[i].item_code  = PI_ITEM_K_IND_GROUP_PROM;
2312         bp->cmd_req_virt->filter_set.item[i++].value    = bp->ind_group_prom;
2313
2314         /* Initialize LLC Group Promiscuous filter */
2315
2316         bp->cmd_req_virt->filter_set.item[i].item_code  = PI_ITEM_K_GROUP_PROM;
2317         bp->cmd_req_virt->filter_set.item[i++].value    = bp->group_prom;
2318
2319         /* Terminate the item code list */
2320
2321         bp->cmd_req_virt->filter_set.item[i].item_code  = PI_ITEM_K_EOL;
2322
2323         /* Issue command to update adapter filters, then return */
2324
2325         if (dfx_hw_dma_cmd_req(bp) != DFX_K_SUCCESS)
2326                 return(DFX_K_FAILURE);
2327         return(DFX_K_SUCCESS);
2328         }
2329
2330
2331 /*
2332  * ======================
2333  * = dfx_hw_dma_cmd_req =
2334  * ======================
2335  *
2336  * Overview:
2337  *   Sends PDQ DMA command to adapter firmware
2338  *
2339  * Returns:
2340  *   Condition code
2341  *
2342  * Arguments:
2343  *   bp - pointer to board information
2344  *
2345  * Functional Description:
2346  *   The command request and response buffers are posted to the adapter in the manner
2347  *   described in the PDQ Port Specification:
2348  *
2349  *              1. Command Response Buffer is posted to adapter.
2350  *              2. Command Request Buffer is posted to adapter.
2351  *              3. Command Request consumer index is polled until it indicates that request
2352  *         buffer has been DMA'd to adapter.
2353  *              4. Command Response consumer index is polled until it indicates that response
2354  *         buffer has been DMA'd from adapter.
2355  *
2356  *   This ordering ensures that a response buffer is already available for the firmware
2357  *   to use once it's done processing the request buffer.
2358  *
2359  * Return Codes:
2360  *   DFX_K_SUCCESS        - DMA command succeeded
2361  *       DFX_K_OUTSTATE   - Adapter is NOT in proper state
2362  *   DFX_K_HW_TIMEOUT - DMA command timed out
2363  *
2364  * Assumptions:
2365  *   Command request buffer has already been filled with desired DMA command.
2366  *
2367  * Side Effects:
2368  *   None
2369  */
2370
2371 static int dfx_hw_dma_cmd_req(DFX_board_t *bp)
2372         {
2373         int status;                     /* adapter status */
2374         int timeout_cnt;        /* used in for loops */
2375
2376         /* Make sure the adapter is in a state that we can issue the DMA command in */
2377
2378         status = dfx_hw_adap_state_rd(bp);
2379         if ((status == PI_STATE_K_RESET)                ||
2380                 (status == PI_STATE_K_HALTED)           ||
2381                 (status == PI_STATE_K_DMA_UNAVAIL)      ||
2382                 (status == PI_STATE_K_UPGRADE))
2383                 return(DFX_K_OUTSTATE);
2384
2385         /* Put response buffer on the command response queue */
2386
2387         bp->descr_block_virt->cmd_rsp[bp->cmd_rsp_reg.index.prod].long_0 = (u32) (PI_RCV_DESCR_M_SOP |
2388                         ((PI_CMD_RSP_K_SIZE_MAX / PI_ALIGN_K_CMD_RSP_BUFF) << PI_RCV_DESCR_V_SEG_LEN));
2389         bp->descr_block_virt->cmd_rsp[bp->cmd_rsp_reg.index.prod].long_1 = bp->cmd_rsp_phys;
2390
2391         /* Bump (and wrap) the producer index and write out to register */
2392
2393         bp->cmd_rsp_reg.index.prod += 1;
2394         bp->cmd_rsp_reg.index.prod &= PI_CMD_RSP_K_NUM_ENTRIES-1;
2395         dfx_port_write_long(bp, PI_PDQ_K_REG_CMD_RSP_PROD, bp->cmd_rsp_reg.lword);
2396
2397         /* Put request buffer on the command request queue */
2398
2399         bp->descr_block_virt->cmd_req[bp->cmd_req_reg.index.prod].long_0 = (u32) (PI_XMT_DESCR_M_SOP |
2400                         PI_XMT_DESCR_M_EOP | (PI_CMD_REQ_K_SIZE_MAX << PI_XMT_DESCR_V_SEG_LEN));
2401         bp->descr_block_virt->cmd_req[bp->cmd_req_reg.index.prod].long_1 = bp->cmd_req_phys;
2402
2403         /* Bump (and wrap) the producer index and write out to register */
2404
2405         bp->cmd_req_reg.index.prod += 1;
2406         bp->cmd_req_reg.index.prod &= PI_CMD_REQ_K_NUM_ENTRIES-1;
2407         dfx_port_write_long(bp, PI_PDQ_K_REG_CMD_REQ_PROD, bp->cmd_req_reg.lword);
2408
2409         /*
2410          * Here we wait for the command request consumer index to be equal
2411          * to the producer, indicating that the adapter has DMAed the request.
2412          */
2413
2414         for (timeout_cnt = 20000; timeout_cnt > 0; timeout_cnt--)
2415                 {
2416                 if (bp->cmd_req_reg.index.prod == (u8)(bp->cons_block_virt->cmd_req))
2417                         break;
2418                 udelay(100);                    /* wait for 100 microseconds */
2419                 }
2420         if (timeout_cnt == 0)
2421                 return(DFX_K_HW_TIMEOUT);
2422
2423         /* Bump (and wrap) the completion index and write out to register */
2424
2425         bp->cmd_req_reg.index.comp += 1;
2426         bp->cmd_req_reg.index.comp &= PI_CMD_REQ_K_NUM_ENTRIES-1;
2427         dfx_port_write_long(bp, PI_PDQ_K_REG_CMD_REQ_PROD, bp->cmd_req_reg.lword);
2428
2429         /*
2430          * Here we wait for the command response consumer index to be equal
2431          * to the producer, indicating that the adapter has DMAed the response.
2432          */
2433
2434         for (timeout_cnt = 20000; timeout_cnt > 0; timeout_cnt--)
2435                 {
2436                 if (bp->cmd_rsp_reg.index.prod == (u8)(bp->cons_block_virt->cmd_rsp))
2437                         break;
2438                 udelay(100);                    /* wait for 100 microseconds */
2439                 }
2440         if (timeout_cnt == 0)
2441                 return(DFX_K_HW_TIMEOUT);
2442
2443         /* Bump (and wrap) the completion index and write out to register */
2444
2445         bp->cmd_rsp_reg.index.comp += 1;
2446         bp->cmd_rsp_reg.index.comp &= PI_CMD_RSP_K_NUM_ENTRIES-1;
2447         dfx_port_write_long(bp, PI_PDQ_K_REG_CMD_RSP_PROD, bp->cmd_rsp_reg.lword);
2448         return(DFX_K_SUCCESS);
2449         }
2450
2451
2452 /*
2453  * ========================
2454  * = dfx_hw_port_ctrl_req =
2455  * ========================
2456  *
2457  * Overview:
2458  *   Sends PDQ port control command to adapter firmware
2459  *
2460  * Returns:
2461  *   Host data register value in host_data if ptr is not NULL
2462  *
2463  * Arguments:
2464  *   bp                 - pointer to board information
2465  *       command        - port control command
2466  *       data_a         - port data A register value
2467  *       data_b         - port data B register value
2468  *       host_data      - ptr to host data register value
2469  *
2470  * Functional Description:
2471  *   Send generic port control command to adapter by writing
2472  *   to various PDQ port registers, then polling for completion.
2473  *
2474  * Return Codes:
2475  *   DFX_K_SUCCESS        - port control command succeeded
2476  *   DFX_K_HW_TIMEOUT - port control command timed out
2477  *
2478  * Assumptions:
2479  *   None
2480  *
2481  * Side Effects:
2482  *   None
2483  */
2484
2485 static int dfx_hw_port_ctrl_req(
2486         DFX_board_t     *bp,
2487         PI_UINT32       command,
2488         PI_UINT32       data_a,
2489         PI_UINT32       data_b,
2490         PI_UINT32       *host_data
2491         )
2492
2493         {
2494         PI_UINT32       port_cmd;               /* Port Control command register value */
2495         int                     timeout_cnt;    /* used in for loops */
2496
2497         /* Set Command Error bit in command longword */
2498
2499         port_cmd = (PI_UINT32) (command | PI_PCTRL_M_CMD_ERROR);
2500
2501         /* Issue port command to the adapter */
2502
2503         dfx_port_write_long(bp, PI_PDQ_K_REG_PORT_DATA_A, data_a);
2504         dfx_port_write_long(bp, PI_PDQ_K_REG_PORT_DATA_B, data_b);
2505         dfx_port_write_long(bp, PI_PDQ_K_REG_PORT_CTRL, port_cmd);
2506
2507         /* Now wait for command to complete */
2508
2509         if (command == PI_PCTRL_M_BLAST_FLASH)
2510                 timeout_cnt = 600000;   /* set command timeout count to 60 seconds */
2511         else
2512                 timeout_cnt = 20000;    /* set command timeout count to 2 seconds */
2513
2514         for (; timeout_cnt > 0; timeout_cnt--)
2515                 {
2516                 dfx_port_read_long(bp, PI_PDQ_K_REG_PORT_CTRL, &port_cmd);
2517                 if (!(port_cmd & PI_PCTRL_M_CMD_ERROR))
2518                         break;
2519                 udelay(100);                    /* wait for 100 microseconds */
2520                 }
2521         if (timeout_cnt == 0)
2522                 return(DFX_K_HW_TIMEOUT);
2523
2524         /*
2525          * If the address of host_data is non-zero, assume caller has supplied a
2526          * non NULL pointer, and return the contents of the HOST_DATA register in
2527          * it.
2528          */
2529
2530         if (host_data != NULL)
2531                 dfx_port_read_long(bp, PI_PDQ_K_REG_HOST_DATA, host_data);
2532         return(DFX_K_SUCCESS);
2533         }
2534
2535
2536 /*
2537  * =====================
2538  * = dfx_hw_adap_reset =
2539  * =====================
2540  *
2541  * Overview:
2542  *   Resets adapter
2543  *
2544  * Returns:
2545  *   None
2546  *
2547  * Arguments:
2548  *   bp   - pointer to board information
2549  *   type - type of reset to perform
2550  *
2551  * Functional Description:
2552  *   Issue soft reset to adapter by writing to PDQ Port Reset
2553  *   register.  Use incoming reset type to tell adapter what
2554  *   kind of reset operation to perform.
2555  *
2556  * Return Codes:
2557  *   None
2558  *
2559  * Assumptions:
2560  *   This routine merely issues a soft reset to the adapter.
2561  *   It is expected that after this routine returns, the caller
2562  *   will appropriately poll the Port Status register for the
2563  *   adapter to enter the proper state.
2564  *
2565  * Side Effects:
2566  *   Internal adapter registers are cleared.
2567  */
2568
2569 static void dfx_hw_adap_reset(
2570         DFX_board_t     *bp,
2571         PI_UINT32       type
2572         )
2573
2574         {
2575         /* Set Reset type and assert reset */
2576
2577         dfx_port_write_long(bp, PI_PDQ_K_REG_PORT_DATA_A, type);        /* tell adapter type of reset */
2578         dfx_port_write_long(bp, PI_PDQ_K_REG_PORT_RESET, PI_RESET_M_ASSERT_RESET);
2579
2580         /* Wait for at least 1 Microsecond according to the spec. We wait 20 just to be safe */
2581
2582         udelay(20);
2583
2584         /* Deassert reset */
2585
2586         dfx_port_write_long(bp, PI_PDQ_K_REG_PORT_RESET, 0);
2587         }
2588
2589
2590 /*
2591  * ========================
2592  * = dfx_hw_adap_state_rd =
2593  * ========================
2594  *
2595  * Overview:
2596  *   Returns current adapter state
2597  *
2598  * Returns:
2599  *   Adapter state per PDQ Port Specification
2600  *
2601  * Arguments:
2602  *   bp - pointer to board information
2603  *
2604  * Functional Description:
2605  *   Reads PDQ Port Status register and returns adapter state.
2606  *
2607  * Return Codes:
2608  *   None
2609  *
2610  * Assumptions:
2611  *   None
2612  *
2613  * Side Effects:
2614  *   None
2615  */
2616
2617 static int dfx_hw_adap_state_rd(DFX_board_t *bp)
2618         {
2619         PI_UINT32 port_status;          /* Port Status register value */
2620
2621         dfx_port_read_long(bp, PI_PDQ_K_REG_PORT_STATUS, &port_status);
2622         return((port_status & PI_PSTATUS_M_STATE) >> PI_PSTATUS_V_STATE);
2623         }
2624
2625
2626 /*
2627  * =====================
2628  * = dfx_hw_dma_uninit =
2629  * =====================
2630  *
2631  * Overview:
2632  *   Brings adapter to DMA_UNAVAILABLE state
2633  *
2634  * Returns:
2635  *   Condition code
2636  *
2637  * Arguments:
2638  *   bp   - pointer to board information
2639  *   type - type of reset to perform
2640  *
2641  * Functional Description:
2642  *   Bring adapter to DMA_UNAVAILABLE state by performing the following:
2643  *              1. Set reset type bit in Port Data A Register then reset adapter.
2644  *              2. Check that adapter is in DMA_UNAVAILABLE state.
2645  *
2646  * Return Codes:
2647  *   DFX_K_SUCCESS        - adapter is in DMA_UNAVAILABLE state
2648  *   DFX_K_HW_TIMEOUT - adapter did not reset properly
2649  *
2650  * Assumptions:
2651  *   None
2652  *
2653  * Side Effects:
2654  *   Internal adapter registers are cleared.
2655  */
2656
2657 static int dfx_hw_dma_uninit(DFX_board_t *bp, PI_UINT32 type)
2658         {
2659         int timeout_cnt;        /* used in for loops */
2660
2661         /* Set reset type bit and reset adapter */
2662
2663         dfx_hw_adap_reset(bp, type);
2664
2665         /* Now wait for adapter to enter DMA_UNAVAILABLE state */
2666
2667         for (timeout_cnt = 100000; timeout_cnt > 0; timeout_cnt--)
2668                 {
2669                 if (dfx_hw_adap_state_rd(bp) == PI_STATE_K_DMA_UNAVAIL)
2670                         break;
2671                 udelay(100);                                    /* wait for 100 microseconds */
2672                 }
2673         if (timeout_cnt == 0)
2674                 return(DFX_K_HW_TIMEOUT);
2675         return(DFX_K_SUCCESS);
2676         }
2677
2678 /*
2679  *      Align an sk_buff to a boundary power of 2
2680  *
2681  */
2682
2683 static void my_skb_align(struct sk_buff *skb, int n)
2684 {
2685         unsigned long x = (unsigned long)skb->data;
2686         unsigned long v;
2687
2688         v = ALIGN(x, n);        /* Where we want to be */
2689
2690         skb_reserve(skb, v - x);
2691 }
2692
2693
2694 /*
2695  * ================
2696  * = dfx_rcv_init =
2697  * ================
2698  *
2699  * Overview:
2700  *   Produces buffers to adapter LLC Host receive descriptor block
2701  *
2702  * Returns:
2703  *   None
2704  *
2705  * Arguments:
2706  *   bp - pointer to board information
2707  *   get_buffers - non-zero if buffers to be allocated
2708  *
2709  * Functional Description:
2710  *   This routine can be called during dfx_adap_init() or during an adapter
2711  *       reset.  It initializes the descriptor block and produces all allocated
2712  *   LLC Host queue receive buffers.
2713  *
2714  * Return Codes:
2715  *   Return 0 on success or -ENOMEM if buffer allocation failed (when using
2716  *   dynamic buffer allocation). If the buffer allocation failed, the
2717  *   already allocated buffers will not be released and the caller should do
2718  *   this.
2719  *
2720  * Assumptions:
2721  *   The PDQ has been reset and the adapter and driver maintained Type 2
2722  *   register indices are cleared.
2723  *
2724  * Side Effects:
2725  *   Receive buffers are posted to the adapter LLC queue and the adapter
2726  *   is notified.
2727  */
2728
2729 static int dfx_rcv_init(DFX_board_t *bp, int get_buffers)
2730         {
2731         int     i, j;                                   /* used in for loop */
2732
2733         /*
2734          *  Since each receive buffer is a single fragment of same length, initialize
2735          *  first longword in each receive descriptor for entire LLC Host descriptor
2736          *  block.  Also initialize second longword in each receive descriptor with
2737          *  physical address of receive buffer.  We'll always allocate receive
2738          *  buffers in powers of 2 so that we can easily fill the 256 entry descriptor
2739          *  block and produce new receive buffers by simply updating the receive
2740          *  producer index.
2741          *
2742          *      Assumptions:
2743          *              To support all shipping versions of PDQ, the receive buffer size
2744          *              must be mod 128 in length and the physical address must be 128 byte
2745          *              aligned.  In other words, bits 0-6 of the length and address must
2746          *              be zero for the following descriptor field entries to be correct on
2747          *              all PDQ-based boards.  We guaranteed both requirements during
2748          *              driver initialization when we allocated memory for the receive buffers.
2749          */
2750
2751         if (get_buffers) {
2752 #ifdef DYNAMIC_BUFFERS
2753         for (i = 0; i < (int)(bp->rcv_bufs_to_post); i++)
2754                 for (j = 0; (i + j) < (int)PI_RCV_DATA_K_NUM_ENTRIES; j += bp->rcv_bufs_to_post)
2755                 {
2756                         struct sk_buff *newskb = __dev_alloc_skb(NEW_SKB_SIZE, GFP_NOIO);
2757                         if (!newskb)
2758                                 return -ENOMEM;
2759                         bp->descr_block_virt->rcv_data[i+j].long_0 = (u32) (PI_RCV_DESCR_M_SOP |
2760                                 ((PI_RCV_DATA_K_SIZE_MAX / PI_ALIGN_K_RCV_DATA_BUFF) << PI_RCV_DESCR_V_SEG_LEN));
2761                         /*
2762                          * align to 128 bytes for compatibility with
2763                          * the old EISA boards.
2764                          */
2765
2766                         my_skb_align(newskb, 128);
2767                         bp->descr_block_virt->rcv_data[i + j].long_1 =
2768                                 (u32)pci_map_single(bp->pci_dev, newskb->data,
2769                                                     NEW_SKB_SIZE,
2770                                                     PCI_DMA_FROMDEVICE);
2771                         /*
2772                          * p_rcv_buff_va is only used inside the
2773                          * kernel so we put the skb pointer here.
2774                          */
2775                         bp->p_rcv_buff_va[i+j] = (char *) newskb;
2776                 }
2777 #else
2778         for (i=0; i < (int)(bp->rcv_bufs_to_post); i++)
2779                 for (j=0; (i + j) < (int)PI_RCV_DATA_K_NUM_ENTRIES; j += bp->rcv_bufs_to_post)
2780                         {
2781                         bp->descr_block_virt->rcv_data[i+j].long_0 = (u32) (PI_RCV_DESCR_M_SOP |
2782                                 ((PI_RCV_DATA_K_SIZE_MAX / PI_ALIGN_K_RCV_DATA_BUFF) << PI_RCV_DESCR_V_SEG_LEN));
2783                         bp->descr_block_virt->rcv_data[i+j].long_1 = (u32) (bp->rcv_block_phys + (i * PI_RCV_DATA_K_SIZE_MAX));
2784                         bp->p_rcv_buff_va[i+j] = (char *) (bp->rcv_block_virt + (i * PI_RCV_DATA_K_SIZE_MAX));
2785                         }
2786 #endif
2787         }
2788
2789         /* Update receive producer and Type 2 register */
2790
2791         bp->rcv_xmt_reg.index.rcv_prod = bp->rcv_bufs_to_post;
2792         dfx_port_write_long(bp, PI_PDQ_K_REG_TYPE_2_PROD, bp->rcv_xmt_reg.lword);
2793         return 0;
2794         }
2795
2796
2797 /*
2798  * =========================
2799  * = dfx_rcv_queue_process =
2800  * =========================
2801  *
2802  * Overview:
2803  *   Process received LLC frames.
2804  *
2805  * Returns:
2806  *   None
2807  *
2808  * Arguments:
2809  *   bp - pointer to board information
2810  *
2811  * Functional Description:
2812  *   Received LLC frames are processed until there are no more consumed frames.
2813  *   Once all frames are processed, the receive buffers are returned to the
2814  *   adapter.  Note that this algorithm fixes the length of time that can be spent
2815  *   in this routine, because there are a fixed number of receive buffers to
2816  *   process and buffers are not produced until this routine exits and returns
2817  *   to the ISR.
2818  *
2819  * Return Codes:
2820  *   None
2821  *
2822  * Assumptions:
2823  *   None
2824  *
2825  * Side Effects:
2826  *   None
2827  */
2828
2829 static void dfx_rcv_queue_process(
2830         DFX_board_t *bp
2831         )
2832
2833         {
2834         PI_TYPE_2_CONSUMER      *p_type_2_cons;         /* ptr to rcv/xmt consumer block register */
2835         char                            *p_buff;                        /* ptr to start of packet receive buffer (FMC descriptor) */
2836         u32                                     descr, pkt_len;         /* FMC descriptor field and packet length */
2837         struct sk_buff          *skb;                           /* pointer to a sk_buff to hold incoming packet data */
2838
2839         /* Service all consumed LLC receive frames */
2840
2841         p_type_2_cons = (PI_TYPE_2_CONSUMER *)(&bp->cons_block_virt->xmt_rcv_data);
2842         while (bp->rcv_xmt_reg.index.rcv_comp != p_type_2_cons->index.rcv_cons)
2843                 {
2844                 /* Process any errors */
2845
2846                 int entry;
2847
2848                 entry = bp->rcv_xmt_reg.index.rcv_comp;
2849 #ifdef DYNAMIC_BUFFERS
2850                 p_buff = (char *) (((struct sk_buff *)bp->p_rcv_buff_va[entry])->data);
2851 #else
2852                 p_buff = (char *) bp->p_rcv_buff_va[entry];
2853 #endif
2854                 memcpy(&descr, p_buff + RCV_BUFF_K_DESCR, sizeof(u32));
2855
2856                 if (descr & PI_FMC_DESCR_M_RCC_FLUSH)
2857                         {
2858                         if (descr & PI_FMC_DESCR_M_RCC_CRC)
2859                                 bp->rcv_crc_errors++;
2860                         else
2861                                 bp->rcv_frame_status_errors++;
2862                         }
2863                 else
2864                 {
2865                         int rx_in_place = 0;
2866
2867                         /* The frame was received without errors - verify packet length */
2868
2869                         pkt_len = (u32)((descr & PI_FMC_DESCR_M_LEN) >> PI_FMC_DESCR_V_LEN);
2870                         pkt_len -= 4;                           /* subtract 4 byte CRC */
2871                         if (!IN_RANGE(pkt_len, FDDI_K_LLC_ZLEN, FDDI_K_LLC_LEN))
2872                                 bp->rcv_length_errors++;
2873                         else{
2874 #ifdef DYNAMIC_BUFFERS
2875                                 if (pkt_len > SKBUFF_RX_COPYBREAK) {
2876                                         struct sk_buff *newskb;
2877
2878                                         newskb = dev_alloc_skb(NEW_SKB_SIZE);
2879                                         if (newskb){
2880                                                 rx_in_place = 1;
2881
2882                                                 my_skb_align(newskb, 128);
2883                                                 skb = (struct sk_buff *)bp->p_rcv_buff_va[entry];
2884                                                 pci_unmap_single(bp->pci_dev,
2885                                                         bp->descr_block_virt->rcv_data[entry].long_1,
2886                                                         NEW_SKB_SIZE,
2887                                                         PCI_DMA_FROMDEVICE);
2888                                                 skb_reserve(skb, RCV_BUFF_K_PADDING);
2889                                                 bp->p_rcv_buff_va[entry] = (char *)newskb;
2890                                                 bp->descr_block_virt->rcv_data[entry].long_1 =
2891                                                         (u32)pci_map_single(bp->pci_dev,
2892                                                                 newskb->data,
2893                                                                 NEW_SKB_SIZE,
2894                                                                 PCI_DMA_FROMDEVICE);
2895                                         } else
2896                                                 skb = NULL;
2897                                 } else
2898 #endif
2899                                         skb = dev_alloc_skb(pkt_len+3); /* alloc new buffer to pass up, add room for PRH */
2900                                 if (skb == NULL)
2901                                         {
2902                                         printk("%s: Could not allocate receive buffer.  Dropping packet.\n", bp->dev->name);
2903                                         bp->rcv_discards++;
2904                                         break;
2905                                         }
2906                                 else {
2907 #ifndef DYNAMIC_BUFFERS
2908                                         if (! rx_in_place)
2909 #endif
2910                                         {
2911                                                 /* Receive buffer allocated, pass receive packet up */
2912
2913                                                 memcpy(skb->data, p_buff + RCV_BUFF_K_PADDING, pkt_len+3);
2914                                         }
2915
2916                                         skb_reserve(skb,3);             /* adjust data field so that it points to FC byte */
2917                                         skb_put(skb, pkt_len);          /* pass up packet length, NOT including CRC */
2918                                         skb->dev = bp->dev;             /* pass up device pointer */
2919
2920                                         skb->protocol = fddi_type_trans(skb, bp->dev);
2921                                         bp->rcv_total_bytes += skb->len;
2922                                         netif_rx(skb);
2923
2924                                         /* Update the rcv counters */
2925                                         bp->dev->last_rx = jiffies;
2926                                         bp->rcv_total_frames++;
2927                                         if (*(p_buff + RCV_BUFF_K_DA) & 0x01)
2928                                                 bp->rcv_multicast_frames++;
2929                                 }
2930                         }
2931                         }
2932
2933                 /*
2934                  * Advance the producer (for recycling) and advance the completion
2935                  * (for servicing received frames).  Note that it is okay to
2936                  * advance the producer without checking that it passes the
2937                  * completion index because they are both advanced at the same
2938                  * rate.
2939                  */
2940
2941                 bp->rcv_xmt_reg.index.rcv_prod += 1;
2942                 bp->rcv_xmt_reg.index.rcv_comp += 1;
2943                 }
2944         }
2945
2946
2947 /*
2948  * =====================
2949  * = dfx_xmt_queue_pkt =
2950  * =====================
2951  *
2952  * Overview:
2953  *   Queues packets for transmission
2954  *
2955  * Returns:
2956  *   Condition code
2957  *
2958  * Arguments:
2959  *   skb - pointer to sk_buff to queue for transmission
2960  *   dev - pointer to device information
2961  *
2962  * Functional Description:
2963  *   Here we assume that an incoming skb transmit request
2964  *   is contained in a single physically contiguous buffer
2965  *   in which the virtual address of the start of packet
2966  *   (skb->data) can be converted to a physical address
2967  *   by using pci_map_single().
2968  *
2969  *   Since the adapter architecture requires a three byte
2970  *   packet request header to prepend the start of packet,
2971  *   we'll write the three byte field immediately prior to
2972  *   the FC byte.  This assumption is valid because we've
2973  *   ensured that dev->hard_header_len includes three pad
2974  *   bytes.  By posting a single fragment to the adapter,
2975  *   we'll reduce the number of descriptor fetches and
2976  *   bus traffic needed to send the request.
2977  *
2978  *   Also, we can't free the skb until after it's been DMA'd
2979  *   out by the adapter, so we'll queue it in the driver and
2980  *   return it in dfx_xmt_done.
2981  *
2982  * Return Codes:
2983  *   0 - driver queued packet, link is unavailable, or skbuff was bad
2984  *       1 - caller should requeue the sk_buff for later transmission
2985  *
2986  * Assumptions:
2987  *       First and foremost, we assume the incoming skb pointer
2988  *   is NOT NULL and is pointing to a valid sk_buff structure.
2989  *
2990  *   The outgoing packet is complete, starting with the
2991  *   frame control byte including the last byte of data,
2992  *   but NOT including the 4 byte CRC.  We'll let the
2993  *   adapter hardware generate and append the CRC.
2994  *
2995  *   The entire packet is stored in one physically
2996  *   contiguous buffer which is not cached and whose
2997  *   32-bit physical address can be determined.
2998  *
2999  *   It's vital that this routine is NOT reentered for the
3000  *   same board and that the OS is not in another section of
3001  *   code (eg. dfx_int_common) for the same board on a
3002  *   different thread.
3003  *
3004  * Side Effects:
3005  *   None
3006  */
3007
3008 static int dfx_xmt_queue_pkt(
3009         struct sk_buff  *skb,
3010         struct net_device       *dev
3011         )
3012
3013         {
3014         DFX_board_t             *bp = dev->priv;
3015         u8                      prod;                           /* local transmit producer index */
3016         PI_XMT_DESCR            *p_xmt_descr;           /* ptr to transmit descriptor block entry */
3017         XMT_DRIVER_DESCR        *p_xmt_drv_descr;       /* ptr to transmit driver descriptor */
3018         unsigned long           flags;
3019
3020         netif_stop_queue(dev);
3021
3022         /*
3023          * Verify that incoming transmit request is OK
3024          *
3025          * Note: The packet size check is consistent with other
3026          *               Linux device drivers, although the correct packet
3027          *               size should be verified before calling the
3028          *               transmit routine.
3029          */
3030
3031         if (!IN_RANGE(skb->len, FDDI_K_LLC_ZLEN, FDDI_K_LLC_LEN))
3032         {
3033                 printk("%s: Invalid packet length - %u bytes\n",
3034                         dev->name, skb->len);
3035                 bp->xmt_length_errors++;                /* bump error counter */
3036                 netif_wake_queue(dev);
3037                 dev_kfree_skb(skb);
3038                 return(0);                              /* return "success" */
3039         }
3040         /*
3041          * See if adapter link is available, if not, free buffer
3042          *
3043          * Note: If the link isn't available, free buffer and return 0
3044          *               rather than tell the upper layer to requeue the packet.
3045          *               The methodology here is that by the time the link
3046          *               becomes available, the packet to be sent will be
3047          *               fairly stale.  By simply dropping the packet, the
3048          *               higher layer protocols will eventually time out
3049          *               waiting for response packets which it won't receive.
3050          */
3051
3052         if (bp->link_available == PI_K_FALSE)
3053                 {
3054                 if (dfx_hw_adap_state_rd(bp) == PI_STATE_K_LINK_AVAIL)  /* is link really available? */
3055                         bp->link_available = PI_K_TRUE;         /* if so, set flag and continue */
3056                 else
3057                         {
3058                         bp->xmt_discards++;                                     /* bump error counter */
3059                         dev_kfree_skb(skb);             /* free sk_buff now */
3060                         netif_wake_queue(dev);
3061                         return(0);                                                      /* return "success" */
3062                         }
3063                 }
3064
3065         spin_lock_irqsave(&bp->lock, flags);
3066
3067         /* Get the current producer and the next free xmt data descriptor */
3068
3069         prod            = bp->rcv_xmt_reg.index.xmt_prod;
3070         p_xmt_descr = &(bp->descr_block_virt->xmt_data[prod]);
3071
3072         /*
3073          * Get pointer to auxiliary queue entry to contain information
3074          * for this packet.
3075          *
3076          * Note: The current xmt producer index will become the
3077          *       current xmt completion index when we complete this
3078          *       packet later on.  So, we'll get the pointer to the
3079          *       next auxiliary queue entry now before we bump the
3080          *       producer index.
3081          */
3082
3083         p_xmt_drv_descr = &(bp->xmt_drv_descr_blk[prod++]);     /* also bump producer index */
3084
3085         /* Write the three PRH bytes immediately before the FC byte */
3086
3087         skb_push(skb,3);
3088         skb->data[0] = DFX_PRH0_BYTE;   /* these byte values are defined */
3089         skb->data[1] = DFX_PRH1_BYTE;   /* in the Motorola FDDI MAC chip */
3090         skb->data[2] = DFX_PRH2_BYTE;   /* specification */
3091
3092         /*
3093          * Write the descriptor with buffer info and bump producer
3094          *
3095          * Note: Since we need to start DMA from the packet request
3096          *               header, we'll add 3 bytes to the DMA buffer length,
3097          *               and we'll determine the physical address of the
3098          *               buffer from the PRH, not skb->data.
3099          *
3100          * Assumptions:
3101          *               1. Packet starts with the frame control (FC) byte
3102          *                  at skb->data.
3103          *               2. The 4-byte CRC is not appended to the buffer or
3104          *                      included in the length.
3105          *               3. Packet length (skb->len) is from FC to end of
3106          *                      data, inclusive.
3107          *               4. The packet length does not exceed the maximum
3108          *                      FDDI LLC frame length of 4491 bytes.
3109          *               5. The entire packet is contained in a physically
3110          *                      contiguous, non-cached, locked memory space
3111          *                      comprised of a single buffer pointed to by
3112          *                      skb->data.
3113          *               6. The physical address of the start of packet
3114          *                      can be determined from the virtual address
3115          *                      by using pci_map_single() and is only 32-bits
3116          *                      wide.
3117          */
3118
3119         p_xmt_descr->long_0     = (u32) (PI_XMT_DESCR_M_SOP | PI_XMT_DESCR_M_EOP | ((skb->len) << PI_XMT_DESCR_V_SEG_LEN));
3120         p_xmt_descr->long_1 = (u32)pci_map_single(bp->pci_dev, skb->data,
3121                                                   skb->len, PCI_DMA_TODEVICE);
3122
3123         /*
3124          * Verify that descriptor is actually available
3125          *
3126          * Note: If descriptor isn't available, return 1 which tells
3127          *       the upper layer to requeue the packet for later
3128          *       transmission.
3129          *
3130          *       We need to ensure that the producer never reaches the
3131          *       completion, except to indicate that the queue is empty.
3132          */
3133
3134         if (prod == bp->rcv_xmt_reg.index.xmt_comp)
3135         {
3136                 skb_pull(skb,3);
3137                 spin_unlock_irqrestore(&bp->lock, flags);
3138                 return(1);                      /* requeue packet for later */
3139         }
3140
3141         /*
3142          * Save info for this packet for xmt done indication routine
3143          *
3144          * Normally, we'd save the producer index in the p_xmt_drv_descr
3145          * structure so that we'd have it handy when we complete this
3146          * packet later (in dfx_xmt_done).  However, since the current
3147          * transmit architecture guarantees a single fragment for the
3148          * entire packet, we can simply bump the completion index by
3149          * one (1) for each completed packet.
3150          *
3151          * Note: If this assumption changes and we're presented with
3152          *       an inconsistent number of transmit fragments for packet
3153          *       data, we'll need to modify this code to save the current
3154          *       transmit producer index.
3155          */
3156
3157         p_xmt_drv_descr->p_skb = skb;
3158
3159         /* Update Type 2 register */
3160
3161         bp->rcv_xmt_reg.index.xmt_prod = prod;
3162         dfx_port_write_long(bp, PI_PDQ_K_REG_TYPE_2_PROD, bp->rcv_xmt_reg.lword);
3163         spin_unlock_irqrestore(&bp->lock, flags);
3164         netif_wake_queue(dev);
3165         return(0);                                                      /* packet queued to adapter */
3166         }
3167
3168
3169 /*
3170  * ================
3171  * = dfx_xmt_done =
3172  * ================
3173  *
3174  * Overview:
3175  *   Processes all frames that have been transmitted.
3176  *
3177  * Returns:
3178  *   None
3179  *
3180  * Arguments:
3181  *   bp - pointer to board information
3182  *
3183  * Functional Description:
3184  *   For all consumed transmit descriptors that have not
3185  *   yet been completed, we'll free the skb we were holding
3186  *   onto using dev_kfree_skb and bump the appropriate
3187  *   counters.
3188  *
3189  * Return Codes:
3190  *   None
3191  *
3192  * Assumptions:
3193  *   The Type 2 register is not updated in this routine.  It is
3194  *   assumed that it will be updated in the ISR when dfx_xmt_done
3195  *   returns.
3196  *
3197  * Side Effects:
3198  *   None
3199  */
3200
3201 static int dfx_xmt_done(DFX_board_t *bp)
3202         {
3203         XMT_DRIVER_DESCR        *p_xmt_drv_descr;       /* ptr to transmit driver descriptor */
3204         PI_TYPE_2_CONSUMER      *p_type_2_cons;         /* ptr to rcv/xmt consumer block register */
3205         u8                      comp;                   /* local transmit completion index */
3206         int                     freed = 0;              /* buffers freed */
3207
3208         /* Service all consumed transmit frames */
3209
3210         p_type_2_cons = (PI_TYPE_2_CONSUMER *)(&bp->cons_block_virt->xmt_rcv_data);
3211         while (bp->rcv_xmt_reg.index.xmt_comp != p_type_2_cons->index.xmt_cons)
3212                 {
3213                 /* Get pointer to the transmit driver descriptor block information */
3214
3215                 p_xmt_drv_descr = &(bp->xmt_drv_descr_blk[bp->rcv_xmt_reg.index.xmt_comp]);
3216
3217                 /* Increment transmit counters */
3218
3219                 bp->xmt_total_frames++;
3220                 bp->xmt_total_bytes += p_xmt_drv_descr->p_skb->len;
3221
3222                 /* Return skb to operating system */
3223                 comp = bp->rcv_xmt_reg.index.xmt_comp;
3224                 pci_unmap_single(bp->pci_dev,
3225                                  bp->descr_block_virt->xmt_data[comp].long_1,
3226                                  p_xmt_drv_descr->p_skb->len,
3227                                  PCI_DMA_TODEVICE);
3228                 dev_kfree_skb_irq(p_xmt_drv_descr->p_skb);
3229
3230                 /*
3231                  * Move to start of next packet by updating completion index
3232                  *
3233                  * Here we assume that a transmit packet request is always
3234                  * serviced by posting one fragment.  We can therefore
3235                  * simplify the completion code by incrementing the
3236                  * completion index by one.  This code will need to be
3237                  * modified if this assumption changes.  See comments
3238                  * in dfx_xmt_queue_pkt for more details.
3239                  */
3240
3241                 bp->rcv_xmt_reg.index.xmt_comp += 1;
3242                 freed++;
3243                 }
3244         return freed;
3245         }
3246
3247
3248 /*
3249  * =================
3250  * = dfx_rcv_flush =
3251  * =================
3252  *
3253  * Overview:
3254  *   Remove all skb's in the receive ring.
3255  *
3256  * Returns:
3257  *   None
3258  *
3259  * Arguments:
3260  *   bp - pointer to board information
3261  *
3262  * Functional Description:
3263  *   Free's all the dynamically allocated skb's that are
3264  *   currently attached to the device receive ring. This
3265  *   function is typically only used when the device is
3266  *   initialized or reinitialized.
3267  *
3268  * Return Codes:
3269  *   None
3270  *
3271  * Side Effects:
3272  *   None
3273  */
3274 #ifdef DYNAMIC_BUFFERS
3275 static void dfx_rcv_flush( DFX_board_t *bp )
3276         {
3277         int i, j;
3278
3279         for (i = 0; i < (int)(bp->rcv_bufs_to_post); i++)
3280                 for (j = 0; (i + j) < (int)PI_RCV_DATA_K_NUM_ENTRIES; j += bp->rcv_bufs_to_post)
3281                 {
3282                         struct sk_buff *skb;
3283                         skb = (struct sk_buff *)bp->p_rcv_buff_va[i+j];
3284                         if (skb)
3285                                 dev_kfree_skb(skb);
3286                         bp->p_rcv_buff_va[i+j] = NULL;
3287                 }
3288
3289         }
3290 #else
3291 static inline void dfx_rcv_flush( DFX_board_t *bp )
3292 {
3293 }
3294 #endif /* DYNAMIC_BUFFERS */
3295
3296 /*
3297  * =================
3298  * = dfx_xmt_flush =
3299  * =================
3300  *
3301  * Overview:
3302  *   Processes all frames whether they've been transmitted
3303  *   or not.
3304  *
3305  * Returns:
3306  *   None
3307  *
3308  * Arguments:
3309  *   bp - pointer to board information
3310  *
3311  * Functional Description:
3312  *   For all produced transmit descriptors that have not
3313  *   yet been completed, we'll free the skb we were holding
3314  *   onto using dev_kfree_skb and bump the appropriate
3315  *   counters.  Of course, it's possible that some of
3316  *   these transmit requests actually did go out, but we
3317  *   won't make that distinction here.  Finally, we'll
3318  *   update the consumer index to match the producer.
3319  *
3320  * Return Codes:
3321  *   None
3322  *
3323  * Assumptions:
3324  *   This routine does NOT update the Type 2 register.  It
3325  *   is assumed that this routine is being called during a
3326  *   transmit flush interrupt, or a shutdown or close routine.
3327  *
3328  * Side Effects:
3329  *   None
3330  */
3331
3332 static void dfx_xmt_flush( DFX_board_t *bp )
3333         {
3334         u32                     prod_cons;              /* rcv/xmt consumer block longword */
3335         XMT_DRIVER_DESCR        *p_xmt_drv_descr;       /* ptr to transmit driver descriptor */
3336         u8                      comp;                   /* local transmit completion index */
3337
3338         /* Flush all outstanding transmit frames */
3339
3340         while (bp->rcv_xmt_reg.index.xmt_comp != bp->rcv_xmt_reg.index.xmt_prod)
3341                 {
3342                 /* Get pointer to the transmit driver descriptor block information */
3343
3344                 p_xmt_drv_descr = &(bp->xmt_drv_descr_blk[bp->rcv_xmt_reg.index.xmt_comp]);
3345
3346                 /* Return skb to operating system */
3347                 comp = bp->rcv_xmt_reg.index.xmt_comp;
3348                 pci_unmap_single(bp->pci_dev,
3349                                  bp->descr_block_virt->xmt_data[comp].long_1,
3350                                  p_xmt_drv_descr->p_skb->len,
3351                                  PCI_DMA_TODEVICE);
3352                 dev_kfree_skb(p_xmt_drv_descr->p_skb);
3353
3354                 /* Increment transmit error counter */
3355
3356                 bp->xmt_discards++;
3357
3358                 /*
3359                  * Move to start of next packet by updating completion index
3360                  *
3361                  * Here we assume that a transmit packet request is always
3362                  * serviced by posting one fragment.  We can therefore
3363                  * simplify the completion code by incrementing the
3364                  * completion index by one.  This code will need to be
3365                  * modified if this assumption changes.  See comments
3366                  * in dfx_xmt_queue_pkt for more details.
3367                  */
3368
3369                 bp->rcv_xmt_reg.index.xmt_comp += 1;
3370                 }
3371
3372         /* Update the transmit consumer index in the consumer block */
3373
3374         prod_cons = (u32)(bp->cons_block_virt->xmt_rcv_data & ~PI_CONS_M_XMT_INDEX);
3375         prod_cons |= (u32)(bp->rcv_xmt_reg.index.xmt_prod << PI_CONS_V_XMT_INDEX);
3376         bp->cons_block_virt->xmt_rcv_data = prod_cons;
3377         }
3378
3379 static void __devexit dfx_remove_one_pci_or_eisa(struct pci_dev *pdev, struct net_device *dev)
3380 {
3381         DFX_board_t     *bp = dev->priv;
3382         int             alloc_size;             /* total buffer size used */
3383
3384         unregister_netdev(dev);
3385         release_region(dev->base_addr,  pdev ? PFI_K_CSR_IO_LEN : PI_ESIC_K_CSR_IO_LEN );
3386
3387         alloc_size = sizeof(PI_DESCR_BLOCK) +
3388                      PI_CMD_REQ_K_SIZE_MAX + PI_CMD_RSP_K_SIZE_MAX +
3389 #ifndef DYNAMIC_BUFFERS
3390                      (bp->rcv_bufs_to_post * PI_RCV_DATA_K_SIZE_MAX) +
3391 #endif
3392                      sizeof(PI_CONSUMER_BLOCK) +
3393                      (PI_ALIGN_K_DESC_BLK - 1);
3394         if (bp->kmalloced)
3395                 pci_free_consistent(pdev, alloc_size, bp->kmalloced,
3396                                     bp->kmalloced_dma);
3397         free_netdev(dev);
3398 }
3399
3400 static void __devexit dfx_remove_one (struct pci_dev *pdev)
3401 {
3402         struct net_device *dev = pci_get_drvdata(pdev);
3403
3404         dfx_remove_one_pci_or_eisa(pdev, dev);
3405         pci_set_drvdata(pdev, NULL);
3406 }
3407
3408 static struct pci_device_id dfx_pci_tbl[] = {
3409         { PCI_VENDOR_ID_DEC, PCI_DEVICE_ID_DEC_FDDI, PCI_ANY_ID, PCI_ANY_ID, },
3410         { 0, }
3411 };
3412 MODULE_DEVICE_TABLE(pci, dfx_pci_tbl);
3413
3414 static struct pci_driver dfx_driver = {
3415         .name           = "defxx",
3416         .probe          = dfx_init_one,
3417         .remove         = __devexit_p(dfx_remove_one),
3418         .id_table       = dfx_pci_tbl,
3419 };
3420
3421 static int dfx_have_pci;
3422 static int dfx_have_eisa;
3423
3424
3425 static void __exit dfx_eisa_cleanup(void)
3426 {
3427         struct net_device *dev = root_dfx_eisa_dev;
3428
3429         while (dev)
3430         {
3431                 struct net_device *tmp;
3432                 DFX_board_t *bp;
3433
3434                 bp = (DFX_board_t*)dev->priv;
3435                 tmp = bp->next;
3436                 dfx_remove_one_pci_or_eisa(NULL, dev);
3437                 dev = tmp;
3438         }
3439 }
3440
3441 static int __init dfx_init(void)
3442 {
3443         int rc_pci, rc_eisa;
3444
3445         rc_pci = pci_register_driver(&dfx_driver);
3446         if (rc_pci >= 0) dfx_have_pci = 1;
3447
3448         rc_eisa = dfx_eisa_init();
3449         if (rc_eisa >= 0) dfx_have_eisa = 1;
3450
3451         return ((rc_eisa < 0) ? 0 : rc_eisa)  + ((rc_pci < 0) ? 0 : rc_pci);
3452 }
3453
3454 static void __exit dfx_cleanup(void)
3455 {
3456         if (dfx_have_pci)
3457                 pci_unregister_driver(&dfx_driver);
3458         if (dfx_have_eisa)
3459                 dfx_eisa_cleanup();
3460
3461 }
3462
3463 module_init(dfx_init);
3464 module_exit(dfx_cleanup);
3465 MODULE_AUTHOR("Lawrence V. Stefani");
3466 MODULE_DESCRIPTION("DEC FDDIcontroller EISA/PCI (DEFEA/DEFPA) driver "
3467                    DRV_VERSION " " DRV_RELDATE);
3468 MODULE_LICENSE("GPL");
3469
3470
3471 /*
3472  * Local variables:
3473  * kernel-compile-command: "gcc -D__KERNEL__ -I/root/linux/include -Wall -Wstrict-prototypes -O2 -pipe -fomit-frame-pointer -fno-strength-reduce -m486 -malign-loops=2 -malign-jumps=2 -malign-functions=2 -c defxx.c"
3474  * End:
3475  */