git.oblomov.eu Git - linux-2.6/blob - drivers/char/synclink_gt.c

   1 /*
   2  * $Id: synclink_gt.c,v 4.36 2006/08/28 20:47:14 paulkf Exp $
   3  *
   4  * Device driver for Microgate SyncLink GT serial adapters.
   5  *
   6  * written by Paul Fulghum for Microgate Corporation
   7  * paulkf@microgate.com
   8  *
   9  * Microgate and SyncLink are trademarks of Microgate Corporation
  10  *
  11  * This code is released under the GNU General Public License (GPL)
  12  *
  13  * THIS SOFTWARE IS PROVIDED ``AS IS'' AND ANY EXPRESS OR IMPLIED
  14  * WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES
  15  * OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
  16  * DISCLAIMED.  IN NO EVENT SHALL THE AUTHOR BE LIABLE FOR ANY DIRECT,
  17  * INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
  18  * (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR
  19  * SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION)
  20  * HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT,
  21  * STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE)
  22  * ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED
  23  * OF THE POSSIBILITY OF SUCH DAMAGE.
  24  */
  25
  26 /*
  27  * DEBUG OUTPUT DEFINITIONS
  28  *
  29  * uncomment lines below to enable specific types of debug output
  30  *
  31  * DBGINFO   information - most verbose output
  32  * DBGERR    serious errors
  33  * DBGBH     bottom half service routine debugging
  34  * DBGISR    interrupt service routine debugging
  35  * DBGDATA   output receive and transmit data
  36  * DBGTBUF   output transmit DMA buffers and registers
  37  * DBGRBUF   output receive DMA buffers and registers
  38  */
  39
  40 #define DBGINFO(fmt) if (debug_level >= DEBUG_LEVEL_INFO) printk fmt
  41 #define DBGERR(fmt) if (debug_level >= DEBUG_LEVEL_ERROR) printk fmt
  42 #define DBGBH(fmt) if (debug_level >= DEBUG_LEVEL_BH) printk fmt
  43 #define DBGISR(fmt) if (debug_level >= DEBUG_LEVEL_ISR) printk fmt
  44 #define DBGDATA(info, buf, size, label) if (debug_level >= DEBUG_LEVEL_DATA) trace_block((info), (buf), (size), (label))
  45 //#define DBGTBUF(info) dump_tbufs(info)
  46 //#define DBGRBUF(info) dump_rbufs(info)
  47
  48
  49 #include <linux/module.h>
  50 #include <linux/version.h>
  51 #include <linux/errno.h>
  52 #include <linux/signal.h>
  53 #include <linux/sched.h>
  54 #include <linux/timer.h>
  55 #include <linux/interrupt.h>
  56 #include <linux/pci.h>
  57 #include <linux/tty.h>
  58 #include <linux/tty_flip.h>
  59 #include <linux/serial.h>
  60 #include <linux/major.h>
  61 #include <linux/string.h>
  62 #include <linux/fcntl.h>
  63 #include <linux/ptrace.h>
  64 #include <linux/ioport.h>
  65 #include <linux/mm.h>
  66 #include <linux/slab.h>
  67 #include <linux/netdevice.h>
  68 #include <linux/vmalloc.h>
  69 #include <linux/init.h>
  70 #include <linux/delay.h>
  71 #include <linux/ioctl.h>
  72 #include <linux/termios.h>
  73 #include <linux/bitops.h>
  74 #include <linux/workqueue.h>
  75 #include <linux/hdlc.h>
  76
  77 #include <asm/system.h>
  78 #include <asm/io.h>
  79 #include <asm/irq.h>
  80 #include <asm/dma.h>
  81 #include <asm/types.h>
  82 #include <asm/uaccess.h>
  83
  84 #include "linux/synclink.h"
  85
  86 #if defined(CONFIG_HDLC) || (defined(CONFIG_HDLC_MODULE) && defined(CONFIG_SYNCLINK_GT_MODULE))
  87 #define SYNCLINK_GENERIC_HDLC 1
  88 #else
  89 #define SYNCLINK_GENERIC_HDLC 0
  90 #endif
  91
  92 /*
  93  * module identification
  94  */
  95 static char *driver_name     = "SyncLink GT";
  96 static char *driver_version  = "$Revision: 4.36 $";
  97 static char *tty_driver_name = "synclink_gt";
  98 static char *tty_dev_prefix  = "ttySLG";
  99 MODULE_LICENSE("GPL");
 100 #define MGSL_MAGIC 0x5401
 101 #define MAX_DEVICES 32
 102
 103 static struct pci_device_id pci_table[] = {
 104         {PCI_VENDOR_ID_MICROGATE, SYNCLINK_GT_DEVICE_ID, PCI_ANY_ID, PCI_ANY_ID,},
 105         {PCI_VENDOR_ID_MICROGATE, SYNCLINK_GT2_DEVICE_ID, PCI_ANY_ID, PCI_ANY_ID,},
 106         {PCI_VENDOR_ID_MICROGATE, SYNCLINK_GT4_DEVICE_ID, PCI_ANY_ID, PCI_ANY_ID,},
 107         {PCI_VENDOR_ID_MICROGATE, SYNCLINK_AC_DEVICE_ID, PCI_ANY_ID, PCI_ANY_ID,},
 108         {0,}, /* terminate list */
 109 };
 110 MODULE_DEVICE_TABLE(pci, pci_table);
 111
 112 static int  init_one(struct pci_dev *dev,const struct pci_device_id *ent);
 113 static void remove_one(struct pci_dev *dev);
 114 static struct pci_driver pci_driver = {
 115         .name           = "synclink_gt",
 116         .id_table       = pci_table,
 117         .probe          = init_one,
 118         .remove         = __devexit_p(remove_one),
 119 };
 120
 121 static int pci_registered;
 122
 123 /*
 124  * module configuration and status
 125  */
 126 static struct slgt_info *slgt_device_list;
 127 static int slgt_device_count;
 128
 129 static int ttymajor;
 130 static int debug_level;
 131 static int maxframe[MAX_DEVICES];
 132 static int dosyncppp[MAX_DEVICES];
 133
 134 module_param(ttymajor, int, 0);
 135 module_param(debug_level, int, 0);
 136 module_param_array(maxframe, int, NULL, 0);
 137 module_param_array(dosyncppp, int, NULL, 0);
 138
 139 MODULE_PARM_DESC(ttymajor, "TTY major device number override: 0=auto assigned");
 140 MODULE_PARM_DESC(debug_level, "Debug syslog output: 0=disabled, 1 to 5=increasing detail");
 141 MODULE_PARM_DESC(maxframe, "Maximum frame size used by device (4096 to 65535)");
 142 MODULE_PARM_DESC(dosyncppp, "Enable synchronous net device, 0=disable 1=enable");
 143
 144 /*
 145  * tty support and callbacks
 146  */
 147 #define RELEVANT_IFLAG(iflag) (iflag & (IGNBRK|BRKINT|IGNPAR|PARMRK|INPCK))
 148
 149 static struct tty_driver *serial_driver;
 150
 151 static int  open(struct tty_struct *tty, struct file * filp);
 152 static void close(struct tty_struct *tty, struct file * filp);
 153 static void hangup(struct tty_struct *tty);
 154 static void set_termios(struct tty_struct *tty, struct ktermios *old_termios);
 155
 156 static int  write(struct tty_struct *tty, const unsigned char *buf, int count);
 157 static void put_char(struct tty_struct *tty, unsigned char ch);
 158 static void send_xchar(struct tty_struct *tty, char ch);
 159 static void wait_until_sent(struct tty_struct *tty, int timeout);
 160 static int  write_room(struct tty_struct *tty);
 161 static void flush_chars(struct tty_struct *tty);
 162 static void flush_buffer(struct tty_struct *tty);
 163 static void tx_hold(struct tty_struct *tty);
 164 static void tx_release(struct tty_struct *tty);
 165
 166 static int  ioctl(struct tty_struct *tty, struct file *file, unsigned int cmd, unsigned long arg);
 167 static int  read_proc(char *page, char **start, off_t off, int count,int *eof, void *data);
 168 static int  chars_in_buffer(struct tty_struct *tty);
 169 static void throttle(struct tty_struct * tty);
 170 static void unthrottle(struct tty_struct * tty);
 171 static void set_break(struct tty_struct *tty, int break_state);
 172
 173 /*
 174  * generic HDLC support and callbacks
 175  */
 176 #if SYNCLINK_GENERIC_HDLC
 177 #define dev_to_port(D) (dev_to_hdlc(D)->priv)
 178 static void hdlcdev_tx_done(struct slgt_info *info);
 179 static void hdlcdev_rx(struct slgt_info *info, char *buf, int size);
 180 static int  hdlcdev_init(struct slgt_info *info);
 181 static void hdlcdev_exit(struct slgt_info *info);
 182 #endif
 183
 184
 185 /*
 186  * device specific structures, macros and functions
 187  */
 188
 189 #define SLGT_MAX_PORTS 4
 190 #define SLGT_REG_SIZE  256
 191
 192 /*
 193  * conditional wait facility
 194  */
 195 struct cond_wait {
 196         struct cond_wait *next;
 197         wait_queue_head_t q;
 198         wait_queue_t wait;
 199         unsigned int data;
 200 };
 201 static void init_cond_wait(struct cond_wait *w, unsigned int data);
 202 static void add_cond_wait(struct cond_wait **head, struct cond_wait *w);
 203 static void remove_cond_wait(struct cond_wait **head, struct cond_wait *w);
 204 static void flush_cond_wait(struct cond_wait **head);
 205
 206 /*
 207  * DMA buffer descriptor and access macros
 208  */
 209 struct slgt_desc
 210 {
 211         unsigned short count;
 212         unsigned short status;
 213         unsigned int pbuf;  /* physical address of data buffer */
 214         unsigned int next;  /* physical address of next descriptor */
 215
 216         /* driver book keeping */
 217         char *buf;          /* virtual  address of data buffer */
 218         unsigned int pdesc; /* physical address of this descriptor */
 219         dma_addr_t buf_dma_addr;
 220 };
 221
 222 #define set_desc_buffer(a,b) (a).pbuf = cpu_to_le32((unsigned int)(b))
 223 #define set_desc_next(a,b) (a).next   = cpu_to_le32((unsigned int)(b))
 224 #define set_desc_count(a,b)(a).count  = cpu_to_le16((unsigned short)(b))
 225 #define set_desc_eof(a,b)  (a).status = cpu_to_le16((b) ? (le16_to_cpu((a).status) | BIT0) : (le16_to_cpu((a).status) & ~BIT0))
 226 #define desc_count(a)      (le16_to_cpu((a).count))
 227 #define desc_status(a)     (le16_to_cpu((a).status))
 228 #define desc_complete(a)   (le16_to_cpu((a).status) & BIT15)
 229 #define desc_eof(a)        (le16_to_cpu((a).status) & BIT2)
 230 #define desc_crc_error(a)  (le16_to_cpu((a).status) & BIT1)
 231 #define desc_abort(a)      (le16_to_cpu((a).status) & BIT0)
 232 #define desc_residue(a)    ((le16_to_cpu((a).status) & 0x38) >> 3)
 233
 234 struct _input_signal_events {
 235         int ri_up;
 236         int ri_down;
 237         int dsr_up;
 238         int dsr_down;
 239         int dcd_up;
 240         int dcd_down;
 241         int cts_up;
 242         int cts_down;
 243 };
 244
 245 /*
 246  * device instance data structure
 247  */
 248 struct slgt_info {
 249         void *if_ptr;           /* General purpose pointer (used by SPPP) */
 250
 251         struct slgt_info *next_device;  /* device list link */
 252
 253         int magic;
 254         int flags;
 255
 256         char device_name[25];
 257         struct pci_dev *pdev;
 258
 259         int port_count;  /* count of ports on adapter */
 260         int adapter_num; /* adapter instance number */
 261         int port_num;    /* port instance number */
 262
 263         /* array of pointers to port contexts on this adapter */
 264         struct slgt_info *port_array[SLGT_MAX_PORTS];
 265
 266         int                     count;          /* count of opens */
 267         int                     line;           /* tty line instance number */
 268         unsigned short          close_delay;
 269         unsigned short          closing_wait;   /* time to wait before closing */
 270
 271         struct mgsl_icount      icount;
 272
 273         struct tty_struct       *tty;
 274         int                     timeout;
 275         int                     x_char;         /* xon/xoff character */
 276         int                     blocked_open;   /* # of blocked opens */
 277         unsigned int            read_status_mask;
 278         unsigned int            ignore_status_mask;
 279
 280         wait_queue_head_t       open_wait;
 281         wait_queue_head_t       close_wait;
 282
 283         wait_queue_head_t       status_event_wait_q;
 284         wait_queue_head_t       event_wait_q;
 285         struct timer_list       tx_timer;
 286         struct timer_list       rx_timer;
 287
 288         unsigned int            gpio_present;
 289         struct cond_wait        *gpio_wait_q;
 290
 291         spinlock_t lock;        /* spinlock for synchronizing with ISR */
 292
 293         struct work_struct task;
 294         u32 pending_bh;
 295         int bh_requested;
 296         int bh_running;
 297
 298         int isr_overflow;
 299         int irq_requested;      /* nonzero if IRQ requested */
 300         int irq_occurred;       /* for diagnostics use */
 301
 302         /* device configuration */
 303
 304         unsigned int bus_type;
 305         unsigned int irq_level;
 306         unsigned long irq_flags;
 307
 308         unsigned char __iomem * reg_addr;  /* memory mapped registers address */
 309         u32 phys_reg_addr;
 310         int reg_addr_requested;
 311
 312         MGSL_PARAMS params;       /* communications parameters */
 313         u32 idle_mode;
 314         u32 max_frame_size;       /* as set by device config */
 315
 316         unsigned int raw_rx_size;
 317         unsigned int if_mode;
 318
 319         /* device status */
 320
 321         int rx_enabled;
 322         int rx_restart;
 323
 324         int tx_enabled;
 325         int tx_active;
 326
 327         unsigned char signals;    /* serial signal states */
 328         int init_error;  /* initialization error */
 329
 330         unsigned char *tx_buf;
 331         int tx_count;
 332
 333         char flag_buf[MAX_ASYNC_BUFFER_SIZE];
 334         char char_buf[MAX_ASYNC_BUFFER_SIZE];
 335         BOOLEAN drop_rts_on_tx_done;
 336         struct  _input_signal_events    input_signal_events;
 337
 338         int dcd_chkcount;       /* check counts to prevent */
 339         int cts_chkcount;       /* too many IRQs if a signal */
 340         int dsr_chkcount;       /* is floating */
 341         int ri_chkcount;
 342
 343         char *bufs;             /* virtual address of DMA buffer lists */
 344         dma_addr_t bufs_dma_addr; /* physical address of buffer descriptors */
 345
 346         unsigned int rbuf_count;
 347         struct slgt_desc *rbufs;
 348         unsigned int rbuf_current;
 349         unsigned int rbuf_index;
 350
 351         unsigned int tbuf_count;
 352         struct slgt_desc *tbufs;
 353         unsigned int tbuf_current;
 354         unsigned int tbuf_start;
 355
 356         unsigned char *tmp_rbuf;
 357         unsigned int tmp_rbuf_count;
 358
 359         /* SPPP/Cisco HDLC device parts */
 360
 361         int netcount;
 362         int dosyncppp;
 363         spinlock_t netlock;
 364 #if SYNCLINK_GENERIC_HDLC
 365         struct net_device *netdev;
 366 #endif
 367
 368 };
 369
 370 static MGSL_PARAMS default_params = {
 371         .mode            = MGSL_MODE_HDLC,
 372         .loopback        = 0,
 373         .flags           = HDLC_FLAG_UNDERRUN_ABORT15,
 374         .encoding        = HDLC_ENCODING_NRZI_SPACE,
 375         .clock_speed     = 0,
 376         .addr_filter     = 0xff,
 377         .crc_type        = HDLC_CRC_16_CCITT,
 378         .preamble_length = HDLC_PREAMBLE_LENGTH_8BITS,
 379         .preamble        = HDLC_PREAMBLE_PATTERN_NONE,
 380         .data_rate       = 9600,
 381         .data_bits       = 8,
 382         .stop_bits       = 1,
 383         .parity          = ASYNC_PARITY_NONE
 384 };
 385
 386
 387 #define BH_RECEIVE  1
 388 #define BH_TRANSMIT 2
 389 #define BH_STATUS   4
 390 #define IO_PIN_SHUTDOWN_LIMIT 100
 391
 392 #define DMABUFSIZE 256
 393 #define DESC_LIST_SIZE 4096
 394
 395 #define MASK_PARITY  BIT1
 396 #define MASK_FRAMING BIT0
 397 #define MASK_BREAK   BIT14
 398 #define MASK_OVERRUN BIT4
 399
 400 #define GSR   0x00 /* global status */
 401 #define JCR   0x04 /* JTAG control */
 402 #define IODR  0x08 /* GPIO direction */
 403 #define IOER  0x0c /* GPIO interrupt enable */
 404 #define IOVR  0x10 /* GPIO value */
 405 #define IOSR  0x14 /* GPIO interrupt status */
 406 #define TDR   0x80 /* tx data */
 407 #define RDR   0x80 /* rx data */
 408 #define TCR   0x82 /* tx control */
 409 #define TIR   0x84 /* tx idle */
 410 #define TPR   0x85 /* tx preamble */
 411 #define RCR   0x86 /* rx control */
 412 #define VCR   0x88 /* V.24 control */
 413 #define CCR   0x89 /* clock control */
 414 #define BDR   0x8a /* baud divisor */
 415 #define SCR   0x8c /* serial control */
 416 #define SSR   0x8e /* serial status */
 417 #define RDCSR 0x90 /* rx DMA control/status */
 418 #define TDCSR 0x94 /* tx DMA control/status */
 419 #define RDDAR 0x98 /* rx DMA descriptor address */
 420 #define TDDAR 0x9c /* tx DMA descriptor address */
 421
 422 #define RXIDLE      BIT14
 423 #define RXBREAK     BIT14
 424 #define IRQ_TXDATA  BIT13
 425 #define IRQ_TXIDLE  BIT12
 426 #define IRQ_TXUNDER BIT11 /* HDLC */
 427 #define IRQ_RXDATA  BIT10
 428 #define IRQ_RXIDLE  BIT9  /* HDLC */
 429 #define IRQ_RXBREAK BIT9  /* async */
 430 #define IRQ_RXOVER  BIT8
 431 #define IRQ_DSR     BIT7
 432 #define IRQ_CTS     BIT6
 433 #define IRQ_DCD     BIT5
 434 #define IRQ_RI      BIT4
 435 #define IRQ_ALL     0x3ff0
 436 #define IRQ_MASTER  BIT0
 437
 438 #define slgt_irq_on(info, mask) \
 439         wr_reg16((info), SCR, (unsigned short)(rd_reg16((info), SCR) | (mask)))
 440 #define slgt_irq_off(info, mask) \
 441         wr_reg16((info), SCR, (unsigned short)(rd_reg16((info), SCR) & ~(mask)))
 442
 443 static __u8  rd_reg8(struct slgt_info *info, unsigned int addr);
 444 static void  wr_reg8(struct slgt_info *info, unsigned int addr, __u8 value);
 445 static __u16 rd_reg16(struct slgt_info *info, unsigned int addr);
 446 static void  wr_reg16(struct slgt_info *info, unsigned int addr, __u16 value);
 447 static __u32 rd_reg32(struct slgt_info *info, unsigned int addr);
 448 static void  wr_reg32(struct slgt_info *info, unsigned int addr, __u32 value);
 449
 450 static void  msc_set_vcr(struct slgt_info *info);
 451
 452 static int  startup(struct slgt_info *info);
 453 static int  block_til_ready(struct tty_struct *tty, struct file * filp,struct slgt_info *info);
 454 static void shutdown(struct slgt_info *info);
 455 static void program_hw(struct slgt_info *info);
 456 static void change_params(struct slgt_info *info);
 457
 458 static int  register_test(struct slgt_info *info);
 459 static int  irq_test(struct slgt_info *info);
 460 static int  loopback_test(struct slgt_info *info);
 461 static int  adapter_test(struct slgt_info *info);
 462
 463 static void reset_adapter(struct slgt_info *info);
 464 static void reset_port(struct slgt_info *info);
 465 static void async_mode(struct slgt_info *info);
 466 static void sync_mode(struct slgt_info *info);
 467
 468 static void rx_stop(struct slgt_info *info);
 469 static void rx_start(struct slgt_info *info);
 470 static void reset_rbufs(struct slgt_info *info);
 471 static void free_rbufs(struct slgt_info *info, unsigned int first, unsigned int last);
 472 static void rdma_reset(struct slgt_info *info);
 473 static int  rx_get_frame(struct slgt_info *info);
 474 static int  rx_get_buf(struct slgt_info *info);
 475
 476 static void tx_start(struct slgt_info *info);
 477 static void tx_stop(struct slgt_info *info);
 478 static void tx_set_idle(struct slgt_info *info);
 479 static unsigned int free_tbuf_count(struct slgt_info *info);
 480 static void reset_tbufs(struct slgt_info *info);
 481 static void tdma_reset(struct slgt_info *info);
 482 static void tx_load(struct slgt_info *info, const char *buf, unsigned int count);
 483
 484 static void get_signals(struct slgt_info *info);
 485 static void set_signals(struct slgt_info *info);
 486 static void enable_loopback(struct slgt_info *info);
 487 static void set_rate(struct slgt_info *info, u32 data_rate);
 488
 489 static int  bh_action(struct slgt_info *info);
 490 static void bh_handler(struct work_struct *work);
 491 static void bh_transmit(struct slgt_info *info);
 492 static void isr_serial(struct slgt_info *info);
 493 static void isr_rdma(struct slgt_info *info);
 494 static void isr_txeom(struct slgt_info *info, unsigned short status);
 495 static void isr_tdma(struct slgt_info *info);
 496 static irqreturn_t slgt_interrupt(int irq, void *dev_id);
 497
 498 static int  alloc_dma_bufs(struct slgt_info *info);
 499 static void free_dma_bufs(struct slgt_info *info);
 500 static int  alloc_desc(struct slgt_info *info);
 501 static void free_desc(struct slgt_info *info);
 502 static int  alloc_bufs(struct slgt_info *info, struct slgt_desc *bufs, int count);
 503 static void free_bufs(struct slgt_info *info, struct slgt_desc *bufs, int count);
 504
 505 static int  alloc_tmp_rbuf(struct slgt_info *info);
 506 static void free_tmp_rbuf(struct slgt_info *info);
 507
 508 static void tx_timeout(unsigned long context);
 509 static void rx_timeout(unsigned long context);
 510
 511 /*
 512  * ioctl handlers
 513  */
 514 static int  get_stats(struct slgt_info *info, struct mgsl_icount __user *user_icount);
 515 static int  get_params(struct slgt_info *info, MGSL_PARAMS __user *params);
 516 static int  set_params(struct slgt_info *info, MGSL_PARAMS __user *params);
 517 static int  get_txidle(struct slgt_info *info, int __user *idle_mode);
 518 static int  set_txidle(struct slgt_info *info, int idle_mode);
 519 static int  tx_enable(struct slgt_info *info, int enable);
 520 static int  tx_abort(struct slgt_info *info);
 521 static int  rx_enable(struct slgt_info *info, int enable);
 522 static int  modem_input_wait(struct slgt_info *info,int arg);
 523 static int  wait_mgsl_event(struct slgt_info *info, int __user *mask_ptr);
 524 static int  tiocmget(struct tty_struct *tty, struct file *file);
 525 static int  tiocmset(struct tty_struct *tty, struct file *file,
 526                      unsigned int set, unsigned int clear);
 527 static void set_break(struct tty_struct *tty, int break_state);
 528 static int  get_interface(struct slgt_info *info, int __user *if_mode);
 529 static int  set_interface(struct slgt_info *info, int if_mode);
 530 static int  set_gpio(struct slgt_info *info, struct gpio_desc __user *gpio);
 531 static int  get_gpio(struct slgt_info *info, struct gpio_desc __user *gpio);
 532 static int  wait_gpio(struct slgt_info *info, struct gpio_desc __user *gpio);
 533
 534 /*
 535  * driver functions
 536  */
 537 static void add_device(struct slgt_info *info);
 538 static void device_init(int adapter_num, struct pci_dev *pdev);
 539 static int  claim_resources(struct slgt_info *info);
 540 static void release_resources(struct slgt_info *info);
 541
 542 /*
 543  * DEBUG OUTPUT CODE
 544  */
 545 #ifndef DBGINFO
 546 #define DBGINFO(fmt)
 547 #endif
 548 #ifndef DBGERR
 549 #define DBGERR(fmt)
 550 #endif
 551 #ifndef DBGBH
 552 #define DBGBH(fmt)
 553 #endif
 554 #ifndef DBGISR
 555 #define DBGISR(fmt)
 556 #endif
 557
 558 #ifdef DBGDATA
 559 static void trace_block(struct slgt_info *info, const char *data, int count, const char *label)
 560 {
 561         int i;
 562         int linecount;
 563         printk("%s %s data:\n",info->device_name, label);
 564         while(count) {
 565                 linecount = (count > 16) ? 16 : count;
 566                 for(i=0; i < linecount; i++)
 567                         printk("%02X ",(unsigned char)data[i]);
 568                 for(;i<17;i++)
 569                         printk("   ");
 570                 for(i=0;i<linecount;i++) {
 571                         if (data[i]>=040 && data[i]<=0176)
 572                                 printk("%c",data[i]);
 573                         else
 574                                 printk(".");
 575                 }
 576                 printk("\n");
 577                 data  += linecount;
 578                 count -= linecount;
 579         }
 580 }
 581 #else
 582 #define DBGDATA(info, buf, size, label)
 583 #endif
 584
 585 #ifdef DBGTBUF
 586 static void dump_tbufs(struct slgt_info *info)
 587 {
 588         int i;
 589         printk("tbuf_current=%d\n", info->tbuf_current);
 590         for (i=0 ; i < info->tbuf_count ; i++) {
 591                 printk("%d: count=%04X status=%04X\n",
 592                         i, le16_to_cpu(info->tbufs[i].count), le16_to_cpu(info->tbufs[i].status));
 593         }
 594 }
 595 #else
 596 #define DBGTBUF(info)
 597 #endif
 598
 599 #ifdef DBGRBUF
 600 static void dump_rbufs(struct slgt_info *info)
 601 {
 602         int i;
 603         printk("rbuf_current=%d\n", info->rbuf_current);
 604         for (i=0 ; i < info->rbuf_count ; i++) {
 605                 printk("%d: count=%04X status=%04X\n",
 606                         i, le16_to_cpu(info->rbufs[i].count), le16_to_cpu(info->rbufs[i].status));
 607         }
 608 }
 609 #else
 610 #define DBGRBUF(info)
 611 #endif
 612
 613 static inline int sanity_check(struct slgt_info *info, char *devname, const char *name)
 614 {
 615 #ifdef SANITY_CHECK
 616         if (!info) {
 617                 printk("null struct slgt_info for (%s) in %s\n", devname, name);
 618                 return 1;
 619         }
 620         if (info->magic != MGSL_MAGIC) {
 621                 printk("bad magic number struct slgt_info (%s) in %s\n", devname, name);
 622                 return 1;
 623         }
 624 #else
 625         if (!info)
 626                 return 1;
 627 #endif
 628         return 0;
 629 }
 630
 631 /**
 632  * line discipline callback wrappers
 633  *
 634  * The wrappers maintain line discipline references
 635  * while calling into the line discipline.
 636  *
 637  * ldisc_receive_buf  - pass receive data to line discipline
 638  */
 639 static void ldisc_receive_buf(struct tty_struct *tty,
 640                               const __u8 *data, char *flags, int count)
 641 {
 642         struct tty_ldisc *ld;
 643         if (!tty)
 644                 return;
 645         ld = tty_ldisc_ref(tty);
 646         if (ld) {
 647                 if (ld->receive_buf)
 648                         ld->receive_buf(tty, data, flags, count);
 649                 tty_ldisc_deref(ld);
 650         }
 651 }
 652
 653 /* tty callbacks */
 654
 655 static int open(struct tty_struct *tty, struct file *filp)
 656 {
 657         struct slgt_info *info;
 658         int retval, line;
 659         unsigned long flags;
 660
 661         line = tty->index;
 662         if ((line < 0) || (line >= slgt_device_count)) {
 663                 DBGERR(("%s: open with invalid line #%d.\n", driver_name, line));
 664                 return -ENODEV;
 665         }
 666
 667         info = slgt_device_list;
 668         while(info && info->line != line)
 669                 info = info->next_device;
 670         if (sanity_check(info, tty->name, "open"))
 671                 return -ENODEV;
 672         if (info->init_error) {
 673                 DBGERR(("%s init error=%d\n", info->device_name, info->init_error));
 674                 return -ENODEV;
 675         }
 676
 677         tty->driver_data = info;
 678         info->tty = tty;
 679
 680         DBGINFO(("%s open, old ref count = %d\n", info->device_name, info->count));
 681
 682         /* If port is closing, signal caller to try again */
 683         if (tty_hung_up_p(filp) || info->flags & ASYNC_CLOSING){
 684                 if (info->flags & ASYNC_CLOSING)
 685                         interruptible_sleep_on(&info->close_wait);
 686                 retval = ((info->flags & ASYNC_HUP_NOTIFY) ?
 687                         -EAGAIN : -ERESTARTSYS);
 688                 goto cleanup;
 689         }
 690
 691         info->tty->low_latency = (info->flags & ASYNC_LOW_LATENCY) ? 1 : 0;
 692
 693         spin_lock_irqsave(&info->netlock, flags);
 694         if (info->netcount) {
 695                 retval = -EBUSY;
 696                 spin_unlock_irqrestore(&info->netlock, flags);
 697                 goto cleanup;
 698         }
 699         info->count++;
 700         spin_unlock_irqrestore(&info->netlock, flags);
 701
 702         if (info->count == 1) {
 703                 /* 1st open on this device, init hardware */
 704                 retval = startup(info);
 705                 if (retval < 0)
 706                         goto cleanup;
 707         }
 708
 709         retval = block_til_ready(tty, filp, info);
 710         if (retval) {
 711                 DBGINFO(("%s block_til_ready rc=%d\n", info->device_name, retval));
 712                 goto cleanup;
 713         }
 714
 715         retval = 0;
 716
 717 cleanup:
 718         if (retval) {
 719                 if (tty->count == 1)
 720                         info->tty = NULL; /* tty layer will release tty struct */
 721                 if(info->count)
 722                         info->count--;
 723         }
 724
 725         DBGINFO(("%s open rc=%d\n", info->device_name, retval));
 726         return retval;
 727 }
 728
 729 static void close(struct tty_struct *tty, struct file *filp)
 730 {
 731         struct slgt_info *info = tty->driver_data;
 732
 733         if (sanity_check(info, tty->name, "close"))
 734                 return;
 735         DBGINFO(("%s close entry, count=%d\n", info->device_name, info->count));
 736
 737         if (!info->count)
 738                 return;
 739
 740         if (tty_hung_up_p(filp))
 741                 goto cleanup;
 742
 743         if ((tty->count == 1) && (info->count != 1)) {
 744                 /*
 745                  * tty->count is 1 and the tty structure will be freed.
 746                  * info->count should be one in this case.
 747                  * if it's not, correct it so that the port is shutdown.
 748                  */
 749                 DBGERR(("%s close: bad refcount; tty->count=1, "
 750                        "info->count=%d\n", info->device_name, info->count));
 751                 info->count = 1;
 752         }
 753
 754         info->count--;
 755
 756         /* if at least one open remaining, leave hardware active */
 757         if (info->count)
 758                 goto cleanup;
 759
 760         info->flags |= ASYNC_CLOSING;
 761
 762         /* set tty->closing to notify line discipline to
 763          * only process XON/XOFF characters. Only the N_TTY
 764          * discipline appears to use this (ppp does not).
 765          */
 766         tty->closing = 1;
 767
 768         /* wait for transmit data to clear all layers */
 769
 770         if (info->closing_wait != ASYNC_CLOSING_WAIT_NONE) {
 771                 DBGINFO(("%s call tty_wait_until_sent\n", info->device_name));
 772                 tty_wait_until_sent(tty, info->closing_wait);
 773         }
 774
 775         if (info->flags & ASYNC_INITIALIZED)
 776                 wait_until_sent(tty, info->timeout);
 777         if (tty->driver->flush_buffer)
 778                 tty->driver->flush_buffer(tty);
 779         tty_ldisc_flush(tty);
 780
 781         shutdown(info);
 782
 783         tty->closing = 0;
 784         info->tty = NULL;
 785
 786         if (info->blocked_open) {
 787                 if (info->close_delay) {
 788                         msleep_interruptible(jiffies_to_msecs(info->close_delay));
 789                 }
 790                 wake_up_interruptible(&info->open_wait);
 791         }
 792
 793         info->flags &= ~(ASYNC_NORMAL_ACTIVE|ASYNC_CLOSING);
 794
 795         wake_up_interruptible(&info->close_wait);
 796
 797 cleanup:
 798         DBGINFO(("%s close exit, count=%d\n", tty->driver->name, info->count));
 799 }
 800
 801 static void hangup(struct tty_struct *tty)
 802 {
 803         struct slgt_info *info = tty->driver_data;
 804
 805         if (sanity_check(info, tty->name, "hangup"))
 806                 return;
 807         DBGINFO(("%s hangup\n", info->device_name));
 808
 809         flush_buffer(tty);
 810         shutdown(info);
 811
 812         info->count = 0;
 813         info->flags &= ~ASYNC_NORMAL_ACTIVE;
 814         info->tty = NULL;
 815
 816         wake_up_interruptible(&info->open_wait);
 817 }
 818
 819 static void set_termios(struct tty_struct *tty, struct ktermios *old_termios)
 820 {
 821         struct slgt_info *info = tty->driver_data;
 822         unsigned long flags;
 823
 824         DBGINFO(("%s set_termios\n", tty->driver->name));
 825
 826         /* just return if nothing has changed */
 827         if ((tty->termios->c_cflag == old_termios->c_cflag)
 828             && (RELEVANT_IFLAG(tty->termios->c_iflag)
 829                 == RELEVANT_IFLAG(old_termios->c_iflag)))
 830                 return;
 831
 832         change_params(info);
 833
 834         /* Handle transition to B0 status */
 835         if (old_termios->c_cflag & CBAUD &&
 836             !(tty->termios->c_cflag & CBAUD)) {
 837                 info->signals &= ~(SerialSignal_RTS + SerialSignal_DTR);
 838                 spin_lock_irqsave(&info->lock,flags);
 839                 set_signals(info);
 840                 spin_unlock_irqrestore(&info->lock,flags);
 841         }
 842
 843         /* Handle transition away from B0 status */
 844         if (!(old_termios->c_cflag & CBAUD) &&
 845             tty->termios->c_cflag & CBAUD) {
 846                 info->signals |= SerialSignal_DTR;
 847                 if (!(tty->termios->c_cflag & CRTSCTS) ||
 848                     !test_bit(TTY_THROTTLED, &tty->flags)) {
 849                         info->signals |= SerialSignal_RTS;
 850                 }
 851                 spin_lock_irqsave(&info->lock,flags);
 852                 set_signals(info);
 853                 spin_unlock_irqrestore(&info->lock,flags);
 854         }
 855
 856         /* Handle turning off CRTSCTS */
 857         if (old_termios->c_cflag & CRTSCTS &&
 858             !(tty->termios->c_cflag & CRTSCTS)) {
 859                 tty->hw_stopped = 0;
 860                 tx_release(tty);
 861         }
 862 }
 863
 864 static int write(struct tty_struct *tty,
 865                  const unsigned char *buf, int count)
 866 {
 867         int ret = 0;
 868         struct slgt_info *info = tty->driver_data;
 869         unsigned long flags;
 870
 871         if (sanity_check(info, tty->name, "write"))
 872                 goto cleanup;
 873         DBGINFO(("%s write count=%d\n", info->device_name, count));
 874
 875         if (!info->tx_buf)
 876                 goto cleanup;
 877
 878         if (count > info->max_frame_size) {
 879                 ret = -EIO;
 880                 goto cleanup;
 881         }
 882
 883         if (!count)
 884                 goto cleanup;
 885
 886         if (info->params.mode == MGSL_MODE_RAW ||
 887             info->params.mode == MGSL_MODE_MONOSYNC ||
 888             info->params.mode == MGSL_MODE_BISYNC) {
 889                 unsigned int bufs_needed = (count/DMABUFSIZE);
 890                 unsigned int bufs_free = free_tbuf_count(info);
 891                 if (count % DMABUFSIZE)
 892                         ++bufs_needed;
 893                 if (bufs_needed > bufs_free)
 894                         goto cleanup;
 895         } else {
 896                 if (info->tx_active)
 897                         goto cleanup;
 898                 if (info->tx_count) {
 899                         /* send accumulated data from send_char() calls */
 900                         /* as frame and wait before accepting more data. */
 901                         tx_load(info, info->tx_buf, info->tx_count);
 902                         goto start;
 903                 }
 904         }
 905
 906         ret = info->tx_count = count;
 907         tx_load(info, buf, count);
 908         goto start;
 909
 910 start:
 911         if (info->tx_count && !tty->stopped && !tty->hw_stopped) {
 912                 spin_lock_irqsave(&info->lock,flags);
 913                 if (!info->tx_active)
 914                         tx_start(info);
 915                 spin_unlock_irqrestore(&info->lock,flags);
 916         }
 917
 918 cleanup:
 919         DBGINFO(("%s write rc=%d\n", info->device_name, ret));
 920         return ret;
 921 }
 922
 923 static void put_char(struct tty_struct *tty, unsigned char ch)
 924 {
 925         struct slgt_info *info = tty->driver_data;
 926         unsigned long flags;
 927
 928         if (sanity_check(info, tty->name, "put_char"))
 929                 return;
 930         DBGINFO(("%s put_char(%d)\n", info->device_name, ch));
 931         if (!info->tx_buf)
 932                 return;
 933         spin_lock_irqsave(&info->lock,flags);
 934         if (!info->tx_active && (info->tx_count < info->max_frame_size))
 935                 info->tx_buf[info->tx_count++] = ch;
 936         spin_unlock_irqrestore(&info->lock,flags);
 937 }
 938
 939 static void send_xchar(struct tty_struct *tty, char ch)
 940 {
 941         struct slgt_info *info = tty->driver_data;
 942         unsigned long flags;
 943
 944         if (sanity_check(info, tty->name, "send_xchar"))
 945                 return;
 946         DBGINFO(("%s send_xchar(%d)\n", info->device_name, ch));
 947         info->x_char = ch;
 948         if (ch) {
 949                 spin_lock_irqsave(&info->lock,flags);
 950                 if (!info->tx_enabled)
 951                         tx_start(info);
 952                 spin_unlock_irqrestore(&info->lock,flags);
 953         }
 954 }
 955
 956 static void wait_until_sent(struct tty_struct *tty, int timeout)
 957 {
 958         struct slgt_info *info = tty->driver_data;
 959         unsigned long orig_jiffies, char_time;
 960
 961         if (!info )
 962                 return;
 963         if (sanity_check(info, tty->name, "wait_until_sent"))
 964                 return;
 965         DBGINFO(("%s wait_until_sent entry\n", info->device_name));
 966         if (!(info->flags & ASYNC_INITIALIZED))
 967                 goto exit;
 968
 969         orig_jiffies = jiffies;
 970
 971         /* Set check interval to 1/5 of estimated time to
 972          * send a character, and make it at least 1. The check
 973          * interval should also be less than the timeout.
 974          * Note: use tight timings here to satisfy the NIST-PCTS.
 975          */
 976
 977         if (info->params.data_rate) {
 978                 char_time = info->timeout/(32 * 5);
 979                 if (!char_time)
 980                         char_time++;
 981         } else
 982                 char_time = 1;
 983
 984         if (timeout)
 985                 char_time = min_t(unsigned long, char_time, timeout);
 986
 987         while (info->tx_active) {
 988                 msleep_interruptible(jiffies_to_msecs(char_time));
 989                 if (signal_pending(current))
 990                         break;
 991                 if (timeout && time_after(jiffies, orig_jiffies + timeout))
 992                         break;
 993         }
 994
 995 exit:
 996         DBGINFO(("%s wait_until_sent exit\n", info->device_name));
 997 }
 998
 999 static int write_room(struct tty_struct *tty)
1000 {
1001         struct slgt_info *info = tty->driver_data;
1002         int ret;
1003
1004         if (sanity_check(info, tty->name, "write_room"))
1005                 return 0;
1006         ret = (info->tx_active) ? 0 : HDLC_MAX_FRAME_SIZE;
1007         DBGINFO(("%s write_room=%d\n", info->device_name, ret));
1008         return ret;
1009 }
1010
1011 static void flush_chars(struct tty_struct *tty)
1012 {
1013         struct slgt_info *info = tty->driver_data;
1014         unsigned long flags;
1015
1016         if (sanity_check(info, tty->name, "flush_chars"))
1017                 return;
1018         DBGINFO(("%s flush_chars entry tx_count=%d\n", info->device_name, info->tx_count));
1019
1020         if (info->tx_count <= 0 || tty->stopped ||
1021             tty->hw_stopped || !info->tx_buf)
1022                 return;
1023
1024         DBGINFO(("%s flush_chars start transmit\n", info->device_name));
1025
1026         spin_lock_irqsave(&info->lock,flags);
1027         if (!info->tx_active && info->tx_count) {
1028                 tx_load(info, info->tx_buf,info->tx_count);
1029                 tx_start(info);
1030         }
1031         spin_unlock_irqrestore(&info->lock,flags);
1032 }
1033
1034 static void flush_buffer(struct tty_struct *tty)
1035 {
1036         struct slgt_info *info = tty->driver_data;
1037         unsigned long flags;
1038
1039         if (sanity_check(info, tty->name, "flush_buffer"))
1040                 return;
1041         DBGINFO(("%s flush_buffer\n", info->device_name));
1042
1043         spin_lock_irqsave(&info->lock,flags);
1044         if (!info->tx_active)
1045                 info->tx_count = 0;
1046         spin_unlock_irqrestore(&info->lock,flags);
1047
1048         wake_up_interruptible(&tty->write_wait);
1049         tty_wakeup(tty);
1050 }
1051
1052 /*
1053  * throttle (stop) transmitter
1054  */
1055 static void tx_hold(struct tty_struct *tty)
1056 {
1057         struct slgt_info *info = tty->driver_data;
1058         unsigned long flags;
1059
1060         if (sanity_check(info, tty->name, "tx_hold"))
1061                 return;
1062         DBGINFO(("%s tx_hold\n", info->device_name));
1063         spin_lock_irqsave(&info->lock,flags);
1064         if (info->tx_enabled && info->params.mode == MGSL_MODE_ASYNC)
1065                 tx_stop(info);
1066         spin_unlock_irqrestore(&info->lock,flags);
1067 }
1068
1069 /*
1070  * release (start) transmitter
1071  */
1072 static void tx_release(struct tty_struct *tty)
1073 {
1074         struct slgt_info *info = tty->driver_data;
1075         unsigned long flags;
1076
1077         if (sanity_check(info, tty->name, "tx_release"))
1078                 return;
1079         DBGINFO(("%s tx_release\n", info->device_name));
1080         spin_lock_irqsave(&info->lock,flags);
1081         if (!info->tx_active && info->tx_count) {
1082                 tx_load(info, info->tx_buf, info->tx_count);
1083                 tx_start(info);
1084         }
1085         spin_unlock_irqrestore(&info->lock,flags);
1086 }
1087
1088 /*
1089  * Service an IOCTL request
1090  *
1091  * Arguments
1092  *
1093  *      tty     pointer to tty instance data
1094  *      file    pointer to associated file object for device
1095  *      cmd     IOCTL command code
1096  *      arg     command argument/context
1097  *
1098  * Return 0 if success, otherwise error code
1099  */
1100 static int ioctl(struct tty_struct *tty, struct file *file,
1101                  unsigned int cmd, unsigned long arg)
1102 {
1103         struct slgt_info *info = tty->driver_data;
1104         struct mgsl_icount cnow;        /* kernel counter temps */
1105         struct serial_icounter_struct __user *p_cuser;  /* user space */
1106         unsigned long flags;
1107         void __user *argp = (void __user *)arg;
1108
1109         if (sanity_check(info, tty->name, "ioctl"))
1110                 return -ENODEV;
1111         DBGINFO(("%s ioctl() cmd=%08X\n", info->device_name, cmd));
1112
1113         if ((cmd != TIOCGSERIAL) && (cmd != TIOCSSERIAL) &&
1114             (cmd != TIOCMIWAIT) && (cmd != TIOCGICOUNT)) {
1115                 if (tty->flags & (1 << TTY_IO_ERROR))
1116                     return -EIO;
1117         }
1118
1119         switch (cmd) {
1120         case MGSL_IOCGPARAMS:
1121                 return get_params(info, argp);
1122         case MGSL_IOCSPARAMS:
1123                 return set_params(info, argp);
1124         case MGSL_IOCGTXIDLE:
1125                 return get_txidle(info, argp);
1126         case MGSL_IOCSTXIDLE:
1127                 return set_txidle(info, (int)arg);
1128         case MGSL_IOCTXENABLE:
1129                 return tx_enable(info, (int)arg);
1130         case MGSL_IOCRXENABLE:
1131                 return rx_enable(info, (int)arg);
1132         case MGSL_IOCTXABORT:
1133                 return tx_abort(info);
1134         case MGSL_IOCGSTATS:
1135                 return get_stats(info, argp);
1136         case MGSL_IOCWAITEVENT:
1137                 return wait_mgsl_event(info, argp);
1138         case TIOCMIWAIT:
1139                 return modem_input_wait(info,(int)arg);
1140         case MGSL_IOCGIF:
1141                 return get_interface(info, argp);
1142         case MGSL_IOCSIF:
1143                 return set_interface(info,(int)arg);
1144         case MGSL_IOCSGPIO:
1145                 return set_gpio(info, argp);
1146         case MGSL_IOCGGPIO:
1147                 return get_gpio(info, argp);
1148         case MGSL_IOCWAITGPIO:
1149                 return wait_gpio(info, argp);
1150         case TIOCGICOUNT:
1151                 spin_lock_irqsave(&info->lock,flags);
1152                 cnow = info->icount;
1153                 spin_unlock_irqrestore(&info->lock,flags);
1154                 p_cuser = argp;
1155                 if (put_user(cnow.cts, &p_cuser->cts) ||
1156                     put_user(cnow.dsr, &p_cuser->dsr) ||
1157                     put_user(cnow.rng, &p_cuser->rng) ||
1158                     put_user(cnow.dcd, &p_cuser->dcd) ||
1159                     put_user(cnow.rx, &p_cuser->rx) ||
1160                     put_user(cnow.tx, &p_cuser->tx) ||
1161                     put_user(cnow.frame, &p_cuser->frame) ||
1162                     put_user(cnow.overrun, &p_cuser->overrun) ||
1163                     put_user(cnow.parity, &p_cuser->parity) ||
1164                     put_user(cnow.brk, &p_cuser->brk) ||
1165                     put_user(cnow.buf_overrun, &p_cuser->buf_overrun))
1166                         return -EFAULT;
1167                 return 0;
1168         default:
1169                 return -ENOIOCTLCMD;
1170         }
1171         return 0;
1172 }
1173
1174 /*
1175  * proc fs support
1176  */
1177 static inline int line_info(char *buf, struct slgt_info *info)
1178 {
1179         char stat_buf[30];
1180         int ret;
1181         unsigned long flags;
1182
1183         ret = sprintf(buf, "%s: IO=%08X IRQ=%d MaxFrameSize=%u\n",
1184                       info->device_name, info->phys_reg_addr,
1185                       info->irq_level, info->max_frame_size);
1186
1187         /* output current serial signal states */
1188         spin_lock_irqsave(&info->lock,flags);
1189         get_signals(info);
1190         spin_unlock_irqrestore(&info->lock,flags);
1191
1192         stat_buf[0] = 0;
1193         stat_buf[1] = 0;
1194         if (info->signals & SerialSignal_RTS)
1195                 strcat(stat_buf, "|RTS");
1196         if (info->signals & SerialSignal_CTS)
1197                 strcat(stat_buf, "|CTS");
1198         if (info->signals & SerialSignal_DTR)
1199                 strcat(stat_buf, "|DTR");
1200         if (info->signals & SerialSignal_DSR)
1201                 strcat(stat_buf, "|DSR");
1202         if (info->signals & SerialSignal_DCD)
1203                 strcat(stat_buf, "|CD");
1204         if (info->signals & SerialSignal_RI)
1205                 strcat(stat_buf, "|RI");
1206
1207         if (info->params.mode != MGSL_MODE_ASYNC) {
1208                 ret += sprintf(buf+ret, "\tHDLC txok:%d rxok:%d",
1209                                info->icount.txok, info->icount.rxok);
1210                 if (info->icount.txunder)
1211                         ret += sprintf(buf+ret, " txunder:%d", info->icount.txunder);
1212                 if (info->icount.txabort)
1213                         ret += sprintf(buf+ret, " txabort:%d", info->icount.txabort);
1214                 if (info->icount.rxshort)
1215                         ret += sprintf(buf+ret, " rxshort:%d", info->icount.rxshort);
1216                 if (info->icount.rxlong)
1217                         ret += sprintf(buf+ret, " rxlong:%d", info->icount.rxlong);
1218                 if (info->icount.rxover)
1219                         ret += sprintf(buf+ret, " rxover:%d", info->icount.rxover);
1220                 if (info->icount.rxcrc)
1221                         ret += sprintf(buf+ret, " rxcrc:%d", info->icount.rxcrc);
1222         } else {
1223                 ret += sprintf(buf+ret, "\tASYNC tx:%d rx:%d",
1224                                info->icount.tx, info->icount.rx);
1225                 if (info->icount.frame)
1226                         ret += sprintf(buf+ret, " fe:%d", info->icount.frame);
1227                 if (info->icount.parity)
1228                         ret += sprintf(buf+ret, " pe:%d", info->icount.parity);
1229                 if (info->icount.brk)
1230                         ret += sprintf(buf+ret, " brk:%d", info->icount.brk);
1231                 if (info->icount.overrun)
1232                         ret += sprintf(buf+ret, " oe:%d", info->icount.overrun);
1233         }
1234
1235         /* Append serial signal status to end */
1236         ret += sprintf(buf+ret, " %s\n", stat_buf+1);
1237
1238         ret += sprintf(buf+ret, "\ttxactive=%d bh_req=%d bh_run=%d pending_bh=%x\n",
1239                        info->tx_active,info->bh_requested,info->bh_running,
1240                        info->pending_bh);
1241
1242         return ret;
1243 }
1244
1245 /* Called to print information about devices
1246  */
1247 static int read_proc(char *page, char **start, off_t off, int count,
1248                      int *eof, void *data)
1249 {
1250         int len = 0, l;
1251         off_t   begin = 0;
1252         struct slgt_info *info;
1253
1254         len += sprintf(page, "synclink_gt driver:%s\n", driver_version);
1255
1256         info = slgt_device_list;
1257         while( info ) {
1258                 l = line_info(page + len, info);
1259                 len += l;
1260                 if (len+begin > off+count)
1261                         goto done;
1262                 if (len+begin < off) {
1263                         begin += len;
1264                         len = 0;
1265                 }
1266                 info = info->next_device;
1267         }
1268
1269         *eof = 1;
1270 done:
1271         if (off >= len+begin)
1272                 return 0;
1273         *start = page + (off-begin);
1274         return ((count < begin+len-off) ? count : begin+len-off);
1275 }
1276
1277 /*
1278  * return count of bytes in transmit buffer
1279  */
1280 static int chars_in_buffer(struct tty_struct *tty)
1281 {
1282         struct slgt_info *info = tty->driver_data;
1283         if (sanity_check(info, tty->name, "chars_in_buffer"))
1284                 return 0;
1285         DBGINFO(("%s chars_in_buffer()=%d\n", info->device_name, info->tx_count));
1286         return info->tx_count;
1287 }
1288
1289 /*
1290  * signal remote device to throttle send data (our receive data)
1291  */
1292 static void throttle(struct tty_struct * tty)
1293 {
1294         struct slgt_info *info = tty->driver_data;
1295         unsigned long flags;
1296
1297         if (sanity_check(info, tty->name, "throttle"))
1298                 return;
1299         DBGINFO(("%s throttle\n", info->device_name));
1300         if (I_IXOFF(tty))
1301                 send_xchar(tty, STOP_CHAR(tty));
1302         if (tty->termios->c_cflag & CRTSCTS) {
1303                 spin_lock_irqsave(&info->lock,flags);
1304                 info->signals &= ~SerialSignal_RTS;
1305                 set_signals(info);
1306                 spin_unlock_irqrestore(&info->lock,flags);
1307         }
1308 }
1309
1310 /*
1311  * signal remote device to stop throttling send data (our receive data)
1312  */
1313 static void unthrottle(struct tty_struct * tty)
1314 {
1315         struct slgt_info *info = tty->driver_data;
1316         unsigned long flags;
1317
1318         if (sanity_check(info, tty->name, "unthrottle"))
1319                 return;
1320         DBGINFO(("%s unthrottle\n", info->device_name));
1321         if (I_IXOFF(tty)) {
1322                 if (info->x_char)
1323                         info->x_char = 0;
1324                 else
1325                         send_xchar(tty, START_CHAR(tty));
1326         }
1327         if (tty->termios->c_cflag & CRTSCTS) {
1328                 spin_lock_irqsave(&info->lock,flags);
1329                 info->signals |= SerialSignal_RTS;
1330                 set_signals(info);
1331                 spin_unlock_irqrestore(&info->lock,flags);
1332         }
1333 }
1334
1335 /*
1336  * set or clear transmit break condition
1337  * break_state  -1=set break condition, 0=clear
1338  */
1339 static void set_break(struct tty_struct *tty, int break_state)
1340 {
1341         struct slgt_info *info = tty->driver_data;
1342         unsigned short value;
1343         unsigned long flags;
1344
1345         if (sanity_check(info, tty->name, "set_break"))
1346                 return;
1347         DBGINFO(("%s set_break(%d)\n", info->device_name, break_state));
1348
1349         spin_lock_irqsave(&info->lock,flags);
1350         value = rd_reg16(info, TCR);
1351         if (break_state == -1)
1352                 value |= BIT6;
1353         else
1354                 value &= ~BIT6;
1355         wr_reg16(info, TCR, value);
1356         spin_unlock_irqrestore(&info->lock,flags);
1357 }
1358
1359 #if SYNCLINK_GENERIC_HDLC
1360
1361 /**
1362  * called by generic HDLC layer when protocol selected (PPP, frame relay, etc.)
1363  * set encoding and frame check sequence (FCS) options
1364  *
1365  * dev       pointer to network device structure
1366  * encoding  serial encoding setting
1367  * parity    FCS setting
1368  *
1369  * returns 0 if success, otherwise error code
1370  */
1371 static int hdlcdev_attach(struct net_device *dev, unsigned short encoding,
1372                           unsigned short parity)
1373 {
1374         struct slgt_info *info = dev_to_port(dev);
1375         unsigned char  new_encoding;
1376         unsigned short new_crctype;
1377
1378         /* return error if TTY interface open */
1379         if (info->count)
1380                 return -EBUSY;
1381
1382         DBGINFO(("%s hdlcdev_attach\n", info->device_name));
1383
1384         switch (encoding)
1385         {
1386         case ENCODING_NRZ:        new_encoding = HDLC_ENCODING_NRZ; break;
1387         case ENCODING_NRZI:       new_encoding = HDLC_ENCODING_NRZI_SPACE; break;
1388         case ENCODING_FM_MARK:    new_encoding = HDLC_ENCODING_BIPHASE_MARK; break;
1389         case ENCODING_FM_SPACE:   new_encoding = HDLC_ENCODING_BIPHASE_SPACE; break;
1390         case ENCODING_MANCHESTER: new_encoding = HDLC_ENCODING_BIPHASE_LEVEL; break;
1391         default: return -EINVAL;
1392         }
1393
1394         switch (parity)
1395         {
1396         case PARITY_NONE:            new_crctype = HDLC_CRC_NONE; break;
1397         case PARITY_CRC16_PR1_CCITT: new_crctype = HDLC_CRC_16_CCITT; break;
1398         case PARITY_CRC32_PR1_CCITT: new_crctype = HDLC_CRC_32_CCITT; break;
1399         default: return -EINVAL;
1400         }
1401
1402         info->params.encoding = new_encoding;
1403         info->params.crc_type = new_crctype;
1404
1405         /* if network interface up, reprogram hardware */
1406         if (info->netcount)
1407                 program_hw(info);
1408
1409         return 0;
1410 }
1411
1412 /**
1413  * called by generic HDLC layer to send frame
1414  *
1415  * skb  socket buffer containing HDLC frame
1416  * dev  pointer to network device structure
1417  *
1418  * returns 0 if success, otherwise error code
1419  */
1420 static int hdlcdev_xmit(struct sk_buff *skb, struct net_device *dev)
1421 {
1422         struct slgt_info *info = dev_to_port(dev);
1423         struct net_device_stats *stats = hdlc_stats(dev);
1424         unsigned long flags;
1425
1426         DBGINFO(("%s hdlc_xmit\n", dev->name));
1427
1428         /* stop sending until this frame completes */
1429         netif_stop_queue(dev);
1430
1431         /* copy data to device buffers */
1432         info->tx_count = skb->len;
1433         tx_load(info, skb->data, skb->len);
1434
1435         /* update network statistics */
1436         stats->tx_packets++;
1437         stats->tx_bytes += skb->len;
1438
1439         /* done with socket buffer, so free it */
1440         dev_kfree_skb(skb);
1441
1442         /* save start time for transmit timeout detection */
1443         dev->trans_start = jiffies;
1444
1445         /* start hardware transmitter if necessary */
1446         spin_lock_irqsave(&info->lock,flags);
1447         if (!info->tx_active)
1448                 tx_start(info);
1449         spin_unlock_irqrestore(&info->lock,flags);
1450
1451         return 0;
1452 }
1453
1454 /**
1455  * called by network layer when interface enabled
1456  * claim resources and initialize hardware
1457  *
1458  * dev  pointer to network device structure
1459  *
1460  * returns 0 if success, otherwise error code
1461  */
1462 static int hdlcdev_open(struct net_device *dev)
1463 {
1464         struct slgt_info *info = dev_to_port(dev);
1465         int rc;
1466         unsigned long flags;
1467
1468         DBGINFO(("%s hdlcdev_open\n", dev->name));
1469
1470         /* generic HDLC layer open processing */
1471         if ((rc = hdlc_open(dev)))
1472                 return rc;
1473
1474         /* arbitrate between network and tty opens */
1475         spin_lock_irqsave(&info->netlock, flags);
1476         if (info->count != 0 || info->netcount != 0) {
1477                 DBGINFO(("%s hdlc_open busy\n", dev->name));
1478                 spin_unlock_irqrestore(&info->netlock, flags);
1479                 return -EBUSY;
1480         }
1481         info->netcount=1;
1482         spin_unlock_irqrestore(&info->netlock, flags);
1483
1484         /* claim resources and init adapter */
1485         if ((rc = startup(info)) != 0) {
1486                 spin_lock_irqsave(&info->netlock, flags);
1487                 info->netcount=0;
1488                 spin_unlock_irqrestore(&info->netlock, flags);
1489                 return rc;
1490         }
1491
1492         /* assert DTR and RTS, apply hardware settings */
1493         info->signals |= SerialSignal_RTS + SerialSignal_DTR;
1494         program_hw(info);
1495
1496         /* enable network layer transmit */
1497         dev->trans_start = jiffies;
1498         netif_start_queue(dev);
1499
1500         /* inform generic HDLC layer of current DCD status */
1501         spin_lock_irqsave(&info->lock, flags);
1502         get_signals(info);
1503         spin_unlock_irqrestore(&info->lock, flags);
1504         if (info->signals & SerialSignal_DCD)
1505                 netif_carrier_on(dev);
1506         else
1507                 netif_carrier_off(dev);
1508         return 0;
1509 }
1510
1511 /**
1512  * called by network layer when interface is disabled
1513  * shutdown hardware and release resources
1514  *
1515  * dev  pointer to network device structure
1516  *
1517  * returns 0 if success, otherwise error code
1518  */
1519 static int hdlcdev_close(struct net_device *dev)
1520 {
1521         struct slgt_info *info = dev_to_port(dev);
1522         unsigned long flags;
1523
1524         DBGINFO(("%s hdlcdev_close\n", dev->name));
1525
1526         netif_stop_queue(dev);
1527
1528         /* shutdown adapter and release resources */
1529         shutdown(info);
1530
1531         hdlc_close(dev);
1532
1533         spin_lock_irqsave(&info->netlock, flags);
1534         info->netcount=0;
1535         spin_unlock_irqrestore(&info->netlock, flags);
1536
1537         return 0;
1538 }
1539
1540 /**
1541  * called by network layer to process IOCTL call to network device
1542  *
1543  * dev  pointer to network device structure
1544  * ifr  pointer to network interface request structure
1545  * cmd  IOCTL command code
1546  *
1547  * returns 0 if success, otherwise error code
1548  */
1549 static int hdlcdev_ioctl(struct net_device *dev, struct ifreq *ifr, int cmd)
1550 {
1551         const size_t size = sizeof(sync_serial_settings);
1552         sync_serial_settings new_line;
1553         sync_serial_settings __user *line = ifr->ifr_settings.ifs_ifsu.sync;
1554         struct slgt_info *info = dev_to_port(dev);
1555         unsigned int flags;
1556
1557         DBGINFO(("%s hdlcdev_ioctl\n", dev->name));
1558
1559         /* return error if TTY interface open */
1560         if (info->count)
1561                 return -EBUSY;
1562
1563         if (cmd != SIOCWANDEV)
1564                 return hdlc_ioctl(dev, ifr, cmd);
1565
1566         switch(ifr->ifr_settings.type) {
1567         case IF_GET_IFACE: /* return current sync_serial_settings */
1568
1569                 ifr->ifr_settings.type = IF_IFACE_SYNC_SERIAL;
1570                 if (ifr->ifr_settings.size < size) {
1571                         ifr->ifr_settings.size = size; /* data size wanted */
1572                         return -ENOBUFS;
1573                 }
1574
1575                 flags = info->params.flags & (HDLC_FLAG_RXC_RXCPIN | HDLC_FLAG_RXC_DPLL |
1576                                               HDLC_FLAG_RXC_BRG    | HDLC_FLAG_RXC_TXCPIN |
1577                                               HDLC_FLAG_TXC_TXCPIN | HDLC_FLAG_TXC_DPLL |
1578                                               HDLC_FLAG_TXC_BRG    | HDLC_FLAG_TXC_RXCPIN);
1579
1580                 switch (flags){
1581                 case (HDLC_FLAG_RXC_RXCPIN | HDLC_FLAG_TXC_TXCPIN): new_line.clock_type = CLOCK_EXT; break;
1582                 case (HDLC_FLAG_RXC_BRG    | HDLC_FLAG_TXC_BRG):    new_line.clock_type = CLOCK_INT; break;
1583                 case (HDLC_FLAG_RXC_RXCPIN | HDLC_FLAG_TXC_BRG):    new_line.clock_type = CLOCK_TXINT; break;
1584                 case (HDLC_FLAG_RXC_RXCPIN | HDLC_FLAG_TXC_RXCPIN): new_line.clock_type = CLOCK_TXFROMRX; break;
1585                 default: new_line.clock_type = CLOCK_DEFAULT;
1586                 }
1587
1588                 new_line.clock_rate = info->params.clock_speed;
1589                 new_line.loopback   = info->params.loopback ? 1:0;
1590
1591                 if (copy_to_user(line, &new_line, size))
1592                         return -EFAULT;
1593                 return 0;
1594
1595         case IF_IFACE_SYNC_SERIAL: /* set sync_serial_settings */
1596
1597                 if(!capable(CAP_NET_ADMIN))
1598                         return -EPERM;
1599                 if (copy_from_user(&new_line, line, size))
1600                         return -EFAULT;
1601
1602                 switch (new_line.clock_type)
1603                 {
1604                 case CLOCK_EXT:      flags = HDLC_FLAG_RXC_RXCPIN | HDLC_FLAG_TXC_TXCPIN; break;
1605                 case CLOCK_TXFROMRX: flags = HDLC_FLAG_RXC_RXCPIN | HDLC_FLAG_TXC_RXCPIN; break;
1606                 case CLOCK_INT:      flags = HDLC_FLAG_RXC_BRG    | HDLC_FLAG_TXC_BRG;    break;
1607                 case CLOCK_TXINT:    flags = HDLC_FLAG_RXC_RXCPIN | HDLC_FLAG_TXC_BRG;    break;
1608                 case CLOCK_DEFAULT:  flags = info->params.flags &
1609                                              (HDLC_FLAG_RXC_RXCPIN | HDLC_FLAG_RXC_DPLL |
1610                                               HDLC_FLAG_RXC_BRG    | HDLC_FLAG_RXC_TXCPIN |
1611                                               HDLC_FLAG_TXC_TXCPIN | HDLC_FLAG_TXC_DPLL |
1612                                               HDLC_FLAG_TXC_BRG    | HDLC_FLAG_TXC_RXCPIN); break;
1613                 default: return -EINVAL;
1614                 }
1615
1616                 if (new_line.loopback != 0 && new_line.loopback != 1)
1617                         return -EINVAL;
1618
1619                 info->params.flags &= ~(HDLC_FLAG_RXC_RXCPIN | HDLC_FLAG_RXC_DPLL |
1620                                         HDLC_FLAG_RXC_BRG    | HDLC_FLAG_RXC_TXCPIN |
1621                                         HDLC_FLAG_TXC_TXCPIN | HDLC_FLAG_TXC_DPLL |
1622                                         HDLC_FLAG_TXC_BRG    | HDLC_FLAG_TXC_RXCPIN);
1623                 info->params.flags |= flags;
1624
1625                 info->params.loopback = new_line.loopback;
1626
1627                 if (flags & (HDLC_FLAG_RXC_BRG | HDLC_FLAG_TXC_BRG))
1628                         info->params.clock_speed = new_line.clock_rate;
1629                 else
1630                         info->params.clock_speed = 0;
1631
1632                 /* if network interface up, reprogram hardware */
1633                 if (info->netcount)
1634                         program_hw(info);
1635                 return 0;
1636
1637         default:
1638                 return hdlc_ioctl(dev, ifr, cmd);
1639         }
1640 }
1641
1642 /**
1643  * called by network layer when transmit timeout is detected
1644  *
1645  * dev  pointer to network device structure
1646  */
1647 static void hdlcdev_tx_timeout(struct net_device *dev)
1648 {
1649         struct slgt_info *info = dev_to_port(dev);
1650         struct net_device_stats *stats = hdlc_stats(dev);
1651         unsigned long flags;
1652
1653         DBGINFO(("%s hdlcdev_tx_timeout\n", dev->name));
1654
1655         stats->tx_errors++;
1656         stats->tx_aborted_errors++;
1657
1658         spin_lock_irqsave(&info->lock,flags);
1659         tx_stop(info);
1660         spin_unlock_irqrestore(&info->lock,flags);
1661
1662         netif_wake_queue(dev);
1663 }
1664
1665 /**
1666  * called by device driver when transmit completes
1667  * reenable network layer transmit if stopped
1668  *
1669  * info  pointer to device instance information
1670  */
1671 static void hdlcdev_tx_done(struct slgt_info *info)
1672 {
1673         if (netif_queue_stopped(info->netdev))
1674                 netif_wake_queue(info->netdev);
1675 }
1676
1677 /**
1678  * called by device driver when frame received
1679  * pass frame to network layer
1680  *
1681  * info  pointer to device instance information
1682  * buf   pointer to buffer contianing frame data
1683  * size  count of data bytes in buf
1684  */
1685 static void hdlcdev_rx(struct slgt_info *info, char *buf, int size)
1686 {
1687         struct sk_buff *skb = dev_alloc_skb(size);
1688         struct net_device *dev = info->netdev;
1689         struct net_device_stats *stats = hdlc_stats(dev);
1690
1691         DBGINFO(("%s hdlcdev_rx\n", dev->name));
1692
1693         if (skb == NULL) {
1694                 DBGERR(("%s: can't alloc skb, drop packet\n", dev->name));
1695                 stats->rx_dropped++;
1696                 return;
1697         }
1698
1699         memcpy(skb_put(skb, size),buf,size);
1700
1701         skb->protocol = hdlc_type_trans(skb, info->netdev);
1702
1703         stats->rx_packets++;
1704         stats->rx_bytes += size;
1705
1706         netif_rx(skb);
1707
1708         info->netdev->last_rx = jiffies;
1709 }
1710
1711 /**
1712  * called by device driver when adding device instance
1713  * do generic HDLC initialization
1714  *
1715  * info  pointer to device instance information
1716  *
1717  * returns 0 if success, otherwise error code
1718  */
1719 static int hdlcdev_init(struct slgt_info *info)
1720 {
1721         int rc;
1722         struct net_device *dev;
1723         hdlc_device *hdlc;
1724
1725         /* allocate and initialize network and HDLC layer objects */
1726
1727         if (!(dev = alloc_hdlcdev(info))) {
1728                 printk(KERN_ERR "%s hdlc device alloc failure\n", info->device_name);
1729                 return -ENOMEM;
1730         }
1731
1732         /* for network layer reporting purposes only */
1733         dev->mem_start = info->phys_reg_addr;
1734         dev->mem_end   = info->phys_reg_addr + SLGT_REG_SIZE - 1;
1735         dev->irq       = info->irq_level;
1736
1737         /* network layer callbacks and settings */
1738         dev->do_ioctl       = hdlcdev_ioctl;
1739         dev->open           = hdlcdev_open;
1740         dev->stop           = hdlcdev_close;
1741         dev->tx_timeout     = hdlcdev_tx_timeout;
1742         dev->watchdog_timeo = 10*HZ;
1743         dev->tx_queue_len   = 50;
1744
1745         /* generic HDLC layer callbacks and settings */
1746         hdlc         = dev_to_hdlc(dev);
1747         hdlc->attach = hdlcdev_attach;
1748         hdlc->xmit   = hdlcdev_xmit;
1749
1750         /* register objects with HDLC layer */
1751         if ((rc = register_hdlc_device(dev))) {
1752                 printk(KERN_WARNING "%s:unable to register hdlc device\n",__FILE__);
1753                 free_netdev(dev);
1754                 return rc;
1755         }
1756
1757         info->netdev = dev;
1758         return 0;
1759 }
1760
1761 /**
1762  * called by device driver when removing device instance
1763  * do generic HDLC cleanup
1764  *
1765  * info  pointer to device instance information
1766  */
1767 static void hdlcdev_exit(struct slgt_info *info)
1768 {
1769         unregister_hdlc_device(info->netdev);
1770         free_netdev(info->netdev);
1771         info->netdev = NULL;
1772 }
1773
1774 #endif /* ifdef CONFIG_HDLC */
1775
1776 /*
1777  * get async data from rx DMA buffers
1778  */
1779 static void rx_async(struct slgt_info *info)
1780 {
1781         struct tty_struct *tty = info->tty;
1782         struct mgsl_icount *icount = &info->icount;
1783         unsigned int start, end;
1784         unsigned char *p;
1785         unsigned char status;
1786         struct slgt_desc *bufs = info->rbufs;
1787         int i, count;
1788         int chars = 0;
1789         int stat;
1790         unsigned char ch;
1791
1792         start = end = info->rbuf_current;
1793
1794         while(desc_complete(bufs[end])) {
1795                 count = desc_count(bufs[end]) - info->rbuf_index;
1796                 p     = bufs[end].buf + info->rbuf_index;
1797
1798                 DBGISR(("%s rx_async count=%d\n", info->device_name, count));
1799                 DBGDATA(info, p, count, "rx");
1800
1801                 for(i=0 ; i < count; i+=2, p+=2) {
1802                         ch = *p;
1803                         icount->rx++;
1804
1805                         stat = 0;
1806
1807                         if ((status = *(p+1) & (BIT1 + BIT0))) {
1808                                 if (status & BIT1)
1809                                         icount->parity++;
1810                                 else if (status & BIT0)
1811                                         icount->frame++;
1812                                 /* discard char if tty control flags say so */
1813                                 if (status & info->ignore_status_mask)
1814                                         continue;
1815                                 if (status & BIT1)
1816                                         stat = TTY_PARITY;
1817                                 else if (status & BIT0)
1818                                         stat = TTY_FRAME;
1819                         }
1820                         if (tty) {
1821                                 tty_insert_flip_char(tty, ch, stat);
1822                                 chars++;
1823                         }
1824                 }
1825
1826                 if (i < count) {
1827                         /* receive buffer not completed */
1828                         info->rbuf_index += i;
1829                         info->rx_timer.expires = jiffies + 1;
1830                         add_timer(&info->rx_timer);
1831                         break;
1832                 }
1833
1834                 info->rbuf_index = 0;
1835                 free_rbufs(info, end, end);
1836
1837                 if (++end == info->rbuf_count)
1838                         end = 0;
1839
1840                 /* if entire list searched then no frame available */
1841                 if (end == start)
1842                         break;
1843         }
1844
1845         if (tty && chars)
1846                 tty_flip_buffer_push(tty);
1847 }
1848
1849 /*
1850  * return next bottom half action to perform
1851  */
1852 static int bh_action(struct slgt_info *info)
1853 {
1854         unsigned long flags;
1855         int rc;
1856
1857         spin_lock_irqsave(&info->lock,flags);
1858
1859         if (info->pending_bh & BH_RECEIVE) {
1860                 info->pending_bh &= ~BH_RECEIVE;
1861                 rc = BH_RECEIVE;
1862         } else if (info->pending_bh & BH_TRANSMIT) {
1863                 info->pending_bh &= ~BH_TRANSMIT;
1864                 rc = BH_TRANSMIT;
1865         } else if (info->pending_bh & BH_STATUS) {
1866                 info->pending_bh &= ~BH_STATUS;
1867                 rc = BH_STATUS;
1868         } else {
1869                 /* Mark BH routine as complete */
1870                 info->bh_running   = 0;
1871                 info->bh_requested = 0;
1872                 rc = 0;
1873         }
1874
1875         spin_unlock_irqrestore(&info->lock,flags);
1876
1877         return rc;
1878 }
1879
1880 /*
1881  * perform bottom half processing
1882  */
1883 static void bh_handler(struct work_struct *work)
1884 {
1885         struct slgt_info *info = container_of(work, struct slgt_info, task);
1886         int action;
1887
1888         if (!info)
1889                 return;
1890         info->bh_running = 1;
1891
1892         while((action = bh_action(info))) {
1893                 switch (action) {
1894                 case BH_RECEIVE:
1895                         DBGBH(("%s bh receive\n", info->device_name));
1896                         switch(info->params.mode) {
1897                         case MGSL_MODE_ASYNC:
1898                                 rx_async(info);
1899                                 break;
1900                         case MGSL_MODE_HDLC:
1901                                 while(rx_get_frame(info));
1902                                 break;
1903                         case MGSL_MODE_RAW:
1904                         case MGSL_MODE_MONOSYNC:
1905                         case MGSL_MODE_BISYNC:
1906                                 while(rx_get_buf(info));
1907                                 break;
1908                         }
1909                         /* restart receiver if rx DMA buffers exhausted */
1910                         if (info->rx_restart)
1911                                 rx_start(info);
1912                         break;
1913                 case BH_TRANSMIT:
1914                         bh_transmit(info);
1915                         break;
1916                 case BH_STATUS:
1917                         DBGBH(("%s bh status\n", info->device_name));
1918                         info->ri_chkcount = 0;
1919                         info->dsr_chkcount = 0;
1920                         info->dcd_chkcount = 0;
1921                         info->cts_chkcount = 0;
1922                         break;
1923                 default:
1924                         DBGBH(("%s unknown action\n", info->device_name));
1925                         break;
1926                 }
1927         }
1928         DBGBH(("%s bh_handler exit\n", info->device_name));
1929 }
1930
1931 static void bh_transmit(struct slgt_info *info)
1932 {
1933         struct tty_struct *tty = info->tty;
1934
1935         DBGBH(("%s bh_transmit\n", info->device_name));
1936         if (tty) {
1937                 tty_wakeup(tty);
1938                 wake_up_interruptible(&tty->write_wait);
1939         }
1940 }
1941
1942 static void dsr_change(struct slgt_info *info)
1943 {
1944         get_signals(info);
1945         DBGISR(("dsr_change %s signals=%04X\n", info->device_name, info->signals));
1946         if ((info->dsr_chkcount)++ == IO_PIN_SHUTDOWN_LIMIT) {
1947                 slgt_irq_off(info, IRQ_DSR);
1948                 return;
1949         }
1950         info->icount.dsr++;
1951         if (info->signals & SerialSignal_DSR)
1952                 info->input_signal_events.dsr_up++;
1953         else
1954                 info->input_signal_events.dsr_down++;
1955         wake_up_interruptible(&info->status_event_wait_q);
1956         wake_up_interruptible(&info->event_wait_q);
1957         info->pending_bh |= BH_STATUS;
1958 }
1959
1960 static void cts_change(struct slgt_info *info)
1961 {
1962         get_signals(info);
1963         DBGISR(("cts_change %s signals=%04X\n", info->device_name, info->signals));
1964         if ((info->cts_chkcount)++ == IO_PIN_SHUTDOWN_LIMIT) {
1965                 slgt_irq_off(info, IRQ_CTS);
1966                 return;
1967         }
1968         info->icount.cts++;
1969         if (info->signals & SerialSignal_CTS)
1970                 info->input_signal_events.cts_up++;
1971         else
1972                 info->input_signal_events.cts_down++;
1973         wake_up_interruptible(&info->status_event_wait_q);
1974         wake_up_interruptible(&info->event_wait_q);
1975         info->pending_bh |= BH_STATUS;
1976
1977         if (info->flags & ASYNC_CTS_FLOW) {
1978                 if (info->tty) {
1979                         if (info->tty->hw_stopped) {
1980                                 if (info->signals & SerialSignal_CTS) {
1981                                         info->tty->hw_stopped = 0;
1982                                         info->pending_bh |= BH_TRANSMIT;
1983                                         return;
1984                                 }
1985                         } else {
1986                                 if (!(info->signals & SerialSignal_CTS))
1987                                         info->tty->hw_stopped = 1;
1988                         }
1989                 }
1990         }
1991 }
1992
1993 static void dcd_change(struct slgt_info *info)
1994 {
1995         get_signals(info);
1996         DBGISR(("dcd_change %s signals=%04X\n", info->device_name, info->signals));
1997         if ((info->dcd_chkcount)++ == IO_PIN_SHUTDOWN_LIMIT) {
1998                 slgt_irq_off(info, IRQ_DCD);
1999                 return;
2000         }
2001         info->icount.dcd++;
2002         if (info->signals & SerialSignal_DCD) {
2003                 info->input_signal_events.dcd_up++;
2004         } else {
2005                 info->input_signal_events.dcd_down++;
2006         }
2007 #if SYNCLINK_GENERIC_HDLC
2008         if (info->netcount) {
2009                 if (info->signals & SerialSignal_DCD)
2010                         netif_carrier_on(info->netdev);
2011                 else
2012                         netif_carrier_off(info->netdev);
2013         }
2014 #endif
2015         wake_up_interruptible(&info->status_event_wait_q);
2016         wake_up_interruptible(&info->event_wait_q);
2017         info->pending_bh |= BH_STATUS;
2018
2019         if (info->flags & ASYNC_CHECK_CD) {
2020                 if (info->signals & SerialSignal_DCD)
2021                         wake_up_interruptible(&info->open_wait);
2022                 else {
2023                         if (info->tty)
2024                                 tty_hangup(info->tty);
2025                 }
2026         }
2027 }
2028
2029 static void ri_change(struct slgt_info *info)
2030 {
2031         get_signals(info);
2032         DBGISR(("ri_change %s signals=%04X\n", info->device_name, info->signals));
2033         if ((info->ri_chkcount)++ == IO_PIN_SHUTDOWN_LIMIT) {
2034                 slgt_irq_off(info, IRQ_RI);
2035                 return;
2036         }
2037         info->icount.dcd++;
2038         if (info->signals & SerialSignal_RI) {
2039                 info->input_signal_events.ri_up++;
2040         } else {
2041                 info->input_signal_events.ri_down++;
2042         }
2043         wake_up_interruptible(&info->status_event_wait_q);
2044         wake_up_interruptible(&info->event_wait_q);
2045         info->pending_bh |= BH_STATUS;
2046 }
2047
2048 static void isr_serial(struct slgt_info *info)
2049 {
2050         unsigned short status = rd_reg16(info, SSR);
2051
2052         DBGISR(("%s isr_serial status=%04X\n", info->device_name, status));
2053
2054         wr_reg16(info, SSR, status); /* clear pending */
2055
2056         info->irq_occurred = 1;
2057
2058         if (info->params.mode == MGSL_MODE_ASYNC) {
2059                 if (status & IRQ_TXIDLE) {
2060                         if (info->tx_count)
2061                                 isr_txeom(info, status);
2062                 }
2063                 if ((status & IRQ_RXBREAK) && (status & RXBREAK)) {
2064                         info->icount.brk++;
2065                         /* process break detection if tty control allows */
2066                         if (info->tty) {
2067                                 if (!(status & info->ignore_status_mask)) {
2068                                         if (info->read_status_mask & MASK_BREAK) {
2069                                                 tty_insert_flip_char(info->tty, 0, TTY_BREAK);
2070                                                 if (info->flags & ASYNC_SAK)
2071                                                         do_SAK(info->tty);
2072                                         }
2073                                 }
2074                         }
2075                 }
2076         } else {
2077                 if (status & (IRQ_TXIDLE + IRQ_TXUNDER))
2078                         isr_txeom(info, status);
2079
2080                 if (status & IRQ_RXIDLE) {
2081                         if (status & RXIDLE)
2082                                 info->icount.rxidle++;
2083                         else
2084                                 info->icount.exithunt++;
2085                         wake_up_interruptible(&info->event_wait_q);
2086                 }
2087
2088                 if (status & IRQ_RXOVER)
2089                         rx_start(info);
2090         }
2091
2092         if (status & IRQ_DSR)
2093                 dsr_change(info);
2094         if (status & IRQ_CTS)
2095                 cts_change(info);
2096         if (status & IRQ_DCD)
2097                 dcd_change(info);
2098         if (status & IRQ_RI)
2099                 ri_change(info);
2100 }
2101
2102 static void isr_rdma(struct slgt_info *info)
2103 {
2104         unsigned int status = rd_reg32(info, RDCSR);
2105
2106         DBGISR(("%s isr_rdma status=%08x\n", info->device_name, status));
2107
2108         /* RDCSR (rx DMA control/status)
2109          *
2110          * 31..07  reserved
2111          * 06      save status byte to DMA buffer
2112          * 05      error
2113          * 04      eol (end of list)
2114          * 03      eob (end of buffer)
2115          * 02      IRQ enable
2116          * 01      reset
2117          * 00      enable
2118          */
2119         wr_reg32(info, RDCSR, status);  /* clear pending */
2120
2121         if (status & (BIT5 + BIT4)) {
2122                 DBGISR(("%s isr_rdma rx_restart=1\n", info->device_name));
2123                 info->rx_restart = 1;
2124         }
2125         info->pending_bh |= BH_RECEIVE;
2126 }
2127
2128 static void isr_tdma(struct slgt_info *info)
2129 {
2130         unsigned int status = rd_reg32(info, TDCSR);
2131
2132         DBGISR(("%s isr_tdma status=%08x\n", info->device_name, status));
2133
2134         /* TDCSR (tx DMA control/status)
2135          *
2136          * 31..06  reserved
2137          * 05      error
2138          * 04      eol (end of list)
2139          * 03      eob (end of buffer)
2140          * 02      IRQ enable
2141          * 01      reset
2142          * 00      enable
2143          */
2144         wr_reg32(info, TDCSR, status);  /* clear pending */
2145
2146         if (status & (BIT5 + BIT4 + BIT3)) {
2147                 // another transmit buffer has completed
2148                 // run bottom half to get more send data from user
2149                 info->pending_bh |= BH_TRANSMIT;
2150         }
2151 }
2152
2153 static void isr_txeom(struct slgt_info *info, unsigned short status)
2154 {
2155         DBGISR(("%s txeom status=%04x\n", info->device_name, status));
2156
2157         slgt_irq_off(info, IRQ_TXDATA + IRQ_TXIDLE + IRQ_TXUNDER);
2158         tdma_reset(info);
2159         reset_tbufs(info);
2160         if (status & IRQ_TXUNDER) {
2161                 unsigned short val = rd_reg16(info, TCR);
2162                 wr_reg16(info, TCR, (unsigned short)(val | BIT2)); /* set reset bit */
2163                 wr_reg16(info, TCR, val); /* clear reset bit */
2164         }
2165
2166         if (info->tx_active) {
2167                 if (info->params.mode != MGSL_MODE_ASYNC) {
2168                         if (status & IRQ_TXUNDER)
2169                                 info->icount.txunder++;
2170                         else if (status & IRQ_TXIDLE)
2171                                 info->icount.txok++;
2172                 }
2173
2174                 info->tx_active = 0;
2175                 info->tx_count = 0;
2176
2177                 del_timer(&info->tx_timer);
2178
2179                 if (info->params.mode != MGSL_MODE_ASYNC && info->drop_rts_on_tx_done) {
2180                         info->signals &= ~SerialSignal_RTS;
2181                         info->drop_rts_on_tx_done = 0;
2182                         set_signals(info);
2183                 }
2184
2185 #if SYNCLINK_GENERIC_HDLC
2186                 if (info->netcount)
2187                         hdlcdev_tx_done(info);
2188                 else
2189 #endif
2190                 {
2191                         if (info->tty && (info->tty->stopped || info->tty->hw_stopped)) {
2192                                 tx_stop(info);
2193                                 return;
2194                         }
2195                         info->pending_bh |= BH_TRANSMIT;
2196                 }
2197         }
2198 }
2199
2200 static void isr_gpio(struct slgt_info *info, unsigned int changed, unsigned int state)
2201 {
2202         struct cond_wait *w, *prev;
2203
2204         /* wake processes waiting for specific transitions */
2205         for (w = info->gpio_wait_q, prev = NULL ; w != NULL ; w = w->next) {
2206                 if (w->data & changed) {
2207                         w->data = state;
2208                         wake_up_interruptible(&w->q);
2209                         if (prev != NULL)
2210                                 prev->next = w->next;
2211                         else
2212                                 info->gpio_wait_q = w->next;
2213                 } else
2214                         prev = w;
2215         }
2216 }
2217
2218 /* interrupt service routine
2219  *
2220  *      irq     interrupt number
2221  *      dev_id  device ID supplied during interrupt registration
2222  */
2223 static irqreturn_t slgt_interrupt(int irq, void *dev_id)
2224 {
2225         struct slgt_info *info;
2226         unsigned int gsr;
2227         unsigned int i;
2228
2229         DBGISR(("slgt_interrupt irq=%d entry\n", irq));
2230
2231         info = dev_id;
2232         if (!info)
2233                 return IRQ_NONE;
2234
2235         spin_lock(&info->lock);
2236
2237         while((gsr = rd_reg32(info, GSR) & 0xffffff00)) {
2238                 DBGISR(("%s gsr=%08x\n", info->device_name, gsr));
2239                 info->irq_occurred = 1;
2240                 for(i=0; i < info->port_count ; i++) {
2241                         if (info->port_array[i] == NULL)
2242                                 continue;
2243                         if (gsr & (BIT8 << i))
2244                                 isr_serial(info->port_array[i]);
2245                         if (gsr & (BIT16 << (i*2)))
2246                                 isr_rdma(info->port_array[i]);
2247                         if (gsr & (BIT17 << (i*2)))
2248                                 isr_tdma(info->port_array[i]);
2249                 }
2250         }
2251
2252         if (info->gpio_present) {
2253                 unsigned int state;
2254                 unsigned int changed;
2255                 while ((changed = rd_reg32(info, IOSR)) != 0) {
2256                         DBGISR(("%s iosr=%08x\n", info->device_name, changed));
2257                         /* read latched state of GPIO signals */
2258                         state = rd_reg32(info, IOVR);
2259                         /* clear pending GPIO interrupt bits */
2260                         wr_reg32(info, IOSR, changed);
2261                         for (i=0 ; i < info->port_count ; i++) {
2262                                 if (info->port_array[i] != NULL)
2263                                         isr_gpio(info->port_array[i], changed, state);
2264                         }
2265                 }
2266         }
2267
2268         for(i=0; i < info->port_count ; i++) {
2269                 struct slgt_info *port = info->port_array[i];
2270
2271                 if (port && (port->count || port->netcount) &&
2272                     port->pending_bh && !port->bh_running &&
2273                     !port->bh_requested) {
2274                         DBGISR(("%s bh queued\n", port->device_name));
2275                         schedule_work(&port->task);
2276                         port->bh_requested = 1;
2277                 }
2278         }
2279
2280         spin_unlock(&info->lock);
2281
2282         DBGISR(("slgt_interrupt irq=%d exit\n", irq));
2283         return IRQ_HANDLED;
2284 }
2285
2286 static int startup(struct slgt_info *info)
2287 {
2288         DBGINFO(("%s startup\n", info->device_name));
2289
2290         if (info->flags & ASYNC_INITIALIZED)
2291                 return 0;
2292
2293         if (!info->tx_buf) {
2294                 info->tx_buf = kmalloc(info->max_frame_size, GFP_KERNEL);
2295                 if (!info->tx_buf) {
2296                         DBGERR(("%s can't allocate tx buffer\n", info->device_name));
2297                         return -ENOMEM;
2298                 }
2299         }
2300
2301         info->pending_bh = 0;
2302
2303         memset(&info->icount, 0, sizeof(info->icount));
2304
2305         /* program hardware for current parameters */
2306         change_params(info);
2307
2308         if (info->tty)
2309                 clear_bit(TTY_IO_ERROR, &info->tty->flags);
2310
2311         info->flags |= ASYNC_INITIALIZED;
2312
2313         return 0;
2314 }
2315
2316 /*
2317  *  called by close() and hangup() to shutdown hardware
2318  */
2319 static void shutdown(struct slgt_info *info)
2320 {
2321         unsigned long flags;
2322
2323         if (!(info->flags & ASYNC_INITIALIZED))
2324                 return;
2325
2326         DBGINFO(("%s shutdown\n", info->device_name));
2327
2328         /* clear status wait queue because status changes */
2329         /* can't happen after shutting down the hardware */
2330         wake_up_interruptible(&info->status_event_wait_q);
2331         wake_up_interruptible(&info->event_wait_q);
2332
2333         del_timer_sync(&info->tx_timer);
2334         del_timer_sync(&info->rx_timer);
2335
2336         kfree(info->tx_buf);
2337         info->tx_buf = NULL;
2338
2339         spin_lock_irqsave(&info->lock,flags);
2340
2341         tx_stop(info);
2342         rx_stop(info);
2343
2344         slgt_irq_off(info, IRQ_ALL | IRQ_MASTER);
2345
2346         if (!info->tty || info->tty->termios->c_cflag & HUPCL) {
2347                 info->signals &= ~(SerialSignal_DTR + SerialSignal_RTS);
2348                 set_signals(info);
2349         }
2350
2351         flush_cond_wait(&info->gpio_wait_q);
2352
2353         spin_unlock_irqrestore(&info->lock,flags);
2354
2355         if (info->tty)
2356                 set_bit(TTY_IO_ERROR, &info->tty->flags);
2357
2358         info->flags &= ~ASYNC_INITIALIZED;
2359 }
2360
2361 static void program_hw(struct slgt_info *info)
2362 {
2363         unsigned long flags;
2364
2365         spin_lock_irqsave(&info->lock,flags);
2366
2367         rx_stop(info);
2368         tx_stop(info);
2369
2370         if (info->params.mode != MGSL_MODE_ASYNC ||
2371             info->netcount)
2372                 sync_mode(info);
2373         else
2374                 async_mode(info);
2375
2376         set_signals(info);
2377
2378         info->dcd_chkcount = 0;
2379         info->cts_chkcount = 0;
2380         info->ri_chkcount = 0;
2381         info->dsr_chkcount = 0;
2382
2383         slgt_irq_on(info, IRQ_DCD | IRQ_CTS | IRQ_DSR);
2384         get_signals(info);
2385
2386         if (info->netcount ||
2387             (info->tty && info->tty->termios->c_cflag & CREAD))
2388                 rx_start(info);
2389
2390         spin_unlock_irqrestore(&info->lock,flags);
2391 }
2392
2393 /*
2394  * reconfigure adapter based on new parameters
2395  */
2396 static void change_params(struct slgt_info *info)
2397 {
2398         unsigned cflag;
2399         int bits_per_char;
2400
2401         if (!info->tty || !info->tty->termios)
2402                 return;
2403         DBGINFO(("%s change_params\n", info->device_name));
2404
2405         cflag = info->tty->termios->c_cflag;
2406
2407         /* if B0 rate (hangup) specified then negate DTR and RTS */
2408         /* otherwise assert DTR and RTS */
2409         if (cflag & CBAUD)
2410                 info->signals |= SerialSignal_RTS + SerialSignal_DTR;
2411         else
2412                 info->signals &= ~(SerialSignal_RTS + SerialSignal_DTR);
2413
2414         /* byte size and parity */
2415
2416         switch (cflag & CSIZE) {
2417         case CS5: info->params.data_bits = 5; break;
2418         case CS6: info->params.data_bits = 6; break;
2419         case CS7: info->params.data_bits = 7; break;
2420         case CS8: info->params.data_bits = 8; break;
2421         default:  info->params.data_bits = 7; break;
2422         }
2423
2424         info->params.stop_bits = (cflag & CSTOPB) ? 2 : 1;
2425
2426         if (cflag & PARENB)
2427                 info->params.parity = (cflag & PARODD) ? ASYNC_PARITY_ODD : ASYNC_PARITY_EVEN;
2428         else
2429                 info->params.parity = ASYNC_PARITY_NONE;
2430
2431         /* calculate number of jiffies to transmit a full
2432          * FIFO (32 bytes) at specified data rate
2433          */
2434         bits_per_char = info->params.data_bits +
2435                         info->params.stop_bits + 1;
2436
2437         info->params.data_rate = tty_get_baud_rate(info->tty);
2438
2439         if (info->params.data_rate) {
2440                 info->timeout = (32*HZ*bits_per_char) /
2441                                 info->params.data_rate;
2442         }
2443         info->timeout += HZ/50;         /* Add .02 seconds of slop */
2444
2445         if (cflag & CRTSCTS)
2446                 info->flags |= ASYNC_CTS_FLOW;
2447         else
2448                 info->flags &= ~ASYNC_CTS_FLOW;
2449
2450         if (cflag & CLOCAL)
2451                 info->flags &= ~ASYNC_CHECK_CD;
2452         else
2453                 info->flags |= ASYNC_CHECK_CD;
2454
2455         /* process tty input control flags */
2456
2457         info->read_status_mask = IRQ_RXOVER;
2458         if (I_INPCK(info->tty))
2459                 info->read_status_mask |= MASK_PARITY | MASK_FRAMING;
2460         if (I_BRKINT(info->tty) || I_PARMRK(info->tty))
2461                 info->read_status_mask |= MASK_BREAK;
2462         if (I_IGNPAR(info->tty))
2463                 info->ignore_status_mask |= MASK_PARITY | MASK_FRAMING;
2464         if (I_IGNBRK(info->tty)) {
2465                 info->ignore_status_mask |= MASK_BREAK;
2466                 /* If ignoring parity and break indicators, ignore
2467                  * overruns too.  (For real raw support).
2468                  */
2469                 if (I_IGNPAR(info->tty))
2470                         info->ignore_status_mask |= MASK_OVERRUN;
2471         }
2472
2473         program_hw(info);
2474 }
2475
2476 static int get_stats(struct slgt_info *info, struct mgsl_icount __user *user_icount)
2477 {
2478         DBGINFO(("%s get_stats\n",  info->device_name));
2479         if (!user_icount) {
2480                 memset(&info->icount, 0, sizeof(info->icount));
2481         } else {
2482                 if (copy_to_user(user_icount, &info->icount, sizeof(struct mgsl_icount)))
2483                         return -EFAULT;
2484         }
2485         return 0;
2486 }
2487
2488 static int get_params(struct slgt_info *info, MGSL_PARAMS __user *user_params)
2489 {
2490         DBGINFO(("%s get_params\n", info->device_name));
2491         if (copy_to_user(user_params, &info->params, sizeof(MGSL_PARAMS)))
2492                 return -EFAULT;
2493         return 0;
2494 }
2495
2496 static int set_params(struct slgt_info *info, MGSL_PARAMS __user *new_params)
2497 {
2498         unsigned long flags;
2499         MGSL_PARAMS tmp_params;
2500
2501         DBGINFO(("%s set_params\n", info->device_name));
2502         if (copy_from_user(&tmp_params, new_params, sizeof(MGSL_PARAMS)))
2503                 return -EFAULT;
2504
2505         spin_lock_irqsave(&info->lock, flags);
2506         memcpy(&info->params, &tmp_params, sizeof(MGSL_PARAMS));
2507         spin_unlock_irqrestore(&info->lock, flags);
2508
2509         change_params(info);
2510
2511         return 0;
2512 }
2513
2514 static int get_txidle(struct slgt_info *info, int __user *idle_mode)
2515 {
2516         DBGINFO(("%s get_txidle=%d\n", info->device_name, info->idle_mode));
2517         if (put_user(info->idle_mode, idle_mode))
2518                 return -EFAULT;
2519         return 0;
2520 }
2521
2522 static int set_txidle(struct slgt_info *info, int idle_mode)
2523 {
2524         unsigned long flags;
2525         DBGINFO(("%s set_txidle(%d)\n", info->device_name, idle_mode));
2526         spin_lock_irqsave(&info->lock,flags);
2527         info->idle_mode = idle_mode;
2528         if (info->params.mode != MGSL_MODE_ASYNC)
2529                 tx_set_idle(info);
2530         spin_unlock_irqrestore(&info->lock,flags);
2531         return 0;
2532 }
2533
2534 static int tx_enable(struct slgt_info *info, int enable)
2535 {
2536         unsigned long flags;
2537         DBGINFO(("%s tx_enable(%d)\n", info->device_name, enable));
2538         spin_lock_irqsave(&info->lock,flags);
2539         if (enable) {
2540                 if (!info->tx_enabled)
2541                         tx_start(info);
2542         } else {
2543                 if (info->tx_enabled)
2544                         tx_stop(info);
2545         }
2546         spin_unlock_irqrestore(&info->lock,flags);
2547         return 0;
2548 }
2549
2550 /*
2551  * abort transmit HDLC frame
2552  */
2553 static int tx_abort(struct slgt_info *info)
2554 {
2555         unsigned long flags;
2556         DBGINFO(("%s tx_abort\n", info->device_name));
2557         spin_lock_irqsave(&info->lock,flags);
2558         tdma_reset(info);
2559         spin_unlock_irqrestore(&info->lock,flags);
2560         return 0;
2561 }
2562
2563 static int rx_enable(struct slgt_info *info, int enable)
2564 {
2565         unsigned long flags;
2566         DBGINFO(("%s rx_enable(%d)\n", info->device_name, enable));
2567         spin_lock_irqsave(&info->lock,flags);
2568         if (enable) {
2569                 if (!info->rx_enabled)
2570                         rx_start(info);
2571                 else if (enable == 2) {
2572                         /* force hunt mode (write 1 to RCR[3]) */
2573                         wr_reg16(info, RCR, rd_reg16(info, RCR) | BIT3);
2574                 }
2575         } else {
2576                 if (info->rx_enabled)
2577                         rx_stop(info);
2578         }
2579         spin_unlock_irqrestore(&info->lock,flags);
2580         return 0;
2581 }
2582
2583 /*
2584  *  wait for specified event to occur
2585  */
2586 static int wait_mgsl_event(struct slgt_info *info, int __user *mask_ptr)
2587 {
2588         unsigned long flags;
2589         int s;
2590         int rc=0;
2591         struct mgsl_icount cprev, cnow;
2592         int events;
2593         int mask;
2594         struct  _input_signal_events oldsigs, newsigs;
2595         DECLARE_WAITQUEUE(wait, current);
2596
2597         if (get_user(mask, mask_ptr))
2598                 return -EFAULT;
2599
2600         DBGINFO(("%s wait_mgsl_event(%d)\n", info->device_name, mask));
2601
2602         spin_lock_irqsave(&info->lock,flags);
2603
2604         /* return immediately if state matches requested events */
2605         get_signals(info);
2606         s = info->signals;
2607
2608         events = mask &
2609                 ( ((s & SerialSignal_DSR) ? MgslEvent_DsrActive:MgslEvent_DsrInactive) +
2610                   ((s & SerialSignal_DCD) ? MgslEvent_DcdActive:MgslEvent_DcdInactive) +
2611                   ((s & SerialSignal_CTS) ? MgslEvent_CtsActive:MgslEvent_CtsInactive) +
2612                   ((s & SerialSignal_RI)  ? MgslEvent_RiActive :MgslEvent_RiInactive) );
2613         if (events) {
2614                 spin_unlock_irqrestore(&info->lock,flags);
2615                 goto exit;
2616         }
2617
2618         /* save current irq counts */
2619         cprev = info->icount;
2620         oldsigs = info->input_signal_events;
2621
2622         /* enable hunt and idle irqs if needed */
2623         if (mask & (MgslEvent_ExitHuntMode+MgslEvent_IdleReceived)) {
2624                 unsigned short val = rd_reg16(info, SCR);
2625                 if (!(val & IRQ_RXIDLE))
2626                         wr_reg16(info, SCR, (unsigned short)(val | IRQ_RXIDLE));
2627         }
2628
2629         set_current_state(TASK_INTERRUPTIBLE);
2630         add_wait_queue(&info->event_wait_q, &wait);
2631
2632         spin_unlock_irqrestore(&info->lock,flags);
2633
2634         for(;;) {
2635                 schedule();
2636                 if (signal_pending(current)) {
2637                         rc = -ERESTARTSYS;
2638                         break;
2639                 }
2640
2641                 /* get current irq counts */
2642                 spin_lock_irqsave(&info->lock,flags);
2643                 cnow = info->icount;
2644                 newsigs = info->input_signal_events;
2645                 set_current_state(TASK_INTERRUPTIBLE);
2646                 spin_unlock_irqrestore(&info->lock,flags);
2647
2648                 /* if no change, wait aborted for some reason */
2649                 if (newsigs.dsr_up   == oldsigs.dsr_up   &&
2650                     newsigs.dsr_down == oldsigs.dsr_down &&
2651                     newsigs.dcd_up   == oldsigs.dcd_up   &&
2652                     newsigs.dcd_down == oldsigs.dcd_down &&
2653                     newsigs.cts_up   == oldsigs.cts_up   &&
2654                     newsigs.cts_down == oldsigs.cts_down &&
2655                     newsigs.ri_up    == oldsigs.ri_up    &&
2656                     newsigs.ri_down  == oldsigs.ri_down  &&
2657                     cnow.exithunt    == cprev.exithunt   &&
2658                     cnow.rxidle      == cprev.rxidle) {
2659                         rc = -EIO;
2660                         break;
2661                 }
2662
2663                 events = mask &
2664                         ( (newsigs.dsr_up   != oldsigs.dsr_up   ? MgslEvent_DsrActive:0)   +
2665                           (newsigs.dsr_down != oldsigs.dsr_down ? MgslEvent_DsrInactive:0) +
2666                           (newsigs.dcd_up   != oldsigs.dcd_up   ? MgslEvent_DcdActive:0)   +
2667                           (newsigs.dcd_down != oldsigs.dcd_down ? MgslEvent_DcdInactive:0) +
2668                           (newsigs.cts_up   != oldsigs.cts_up   ? MgslEvent_CtsActive:0)   +
2669                           (newsigs.cts_down != oldsigs.cts_down ? MgslEvent_CtsInactive:0) +
2670                           (newsigs.ri_up    != oldsigs.ri_up    ? MgslEvent_RiActive:0)    +
2671                           (newsigs.ri_down  != oldsigs.ri_down  ? MgslEvent_RiInactive:0)  +
2672                           (cnow.exithunt    != cprev.exithunt   ? MgslEvent_ExitHuntMode:0) +
2673                           (cnow.rxidle      != cprev.rxidle     ? MgslEvent_IdleReceived:0) );
2674                 if (events)
2675                         break;
2676
2677                 cprev = cnow;
2678                 oldsigs = newsigs;
2679         }
2680
2681         remove_wait_queue(&info->event_wait_q, &wait);
2682         set_current_state(TASK_RUNNING);
2683
2684
2685         if (mask & (MgslEvent_ExitHuntMode + MgslEvent_IdleReceived)) {
2686                 spin_lock_irqsave(&info->lock,flags);
2687                 if (!waitqueue_active(&info->event_wait_q)) {
2688                         /* disable enable exit hunt mode/idle rcvd IRQs */
2689                         wr_reg16(info, SCR,
2690                                 (unsigned short)(rd_reg16(info, SCR) & ~IRQ_RXIDLE));
2691                 }
2692                 spin_unlock_irqrestore(&info->lock,flags);
2693         }
2694 exit:
2695         if (rc == 0)
2696                 rc = put_user(events, mask_ptr);
2697         return rc;
2698 }
2699
2700 static int get_interface(struct slgt_info *info, int __user *if_mode)
2701 {
2702         DBGINFO(("%s get_interface=%x\n", info->device_name, info->if_mode));
2703         if (put_user(info->if_mode, if_mode))
2704                 return -EFAULT;
2705         return 0;
2706 }
2707
2708 static int set_interface(struct slgt_info *info, int if_mode)
2709 {
2710         unsigned long flags;
2711         unsigned short val;
2712
2713         DBGINFO(("%s set_interface=%x)\n", info->device_name, if_mode));
2714         spin_lock_irqsave(&info->lock,flags);
2715         info->if_mode = if_mode;
2716
2717         msc_set_vcr(info);
2718
2719         /* TCR (tx control) 07  1=RTS driver control */
2720         val = rd_reg16(info, TCR);
2721         if (info->if_mode & MGSL_INTERFACE_RTS_EN)
2722                 val |= BIT7;
2723         else
2724                 val &= ~BIT7;
2725         wr_reg16(info, TCR, val);
2726
2727         spin_unlock_irqrestore(&info->lock,flags);
2728         return 0;
2729 }
2730
2731 /*
2732  * set general purpose IO pin state and direction
2733  *
2734  * user_gpio fields:
2735  * state   each bit indicates a pin state
2736  * smask   set bit indicates pin state to set
2737  * dir     each bit indicates a pin direction (0=input, 1=output)
2738  * dmask   set bit indicates pin direction to set
2739  */
2740 static int set_gpio(struct slgt_info *info, struct gpio_desc __user *user_gpio)
2741 {
2742         unsigned long flags;
2743         struct gpio_desc gpio;
2744         __u32 data;
2745
2746         if (!info->gpio_present)
2747                 return -EINVAL;
2748         if (copy_from_user(&gpio, user_gpio, sizeof(gpio)))
2749                 return -EFAULT;
2750         DBGINFO(("%s set_gpio state=%08x smask=%08x dir=%08x dmask=%08x\n",
2751                  info->device_name, gpio.state, gpio.smask,
2752                  gpio.dir, gpio.dmask));
2753
2754         spin_lock_irqsave(&info->lock,flags);
2755         if (gpio.dmask) {
2756                 data = rd_reg32(info, IODR);
2757                 data |= gpio.dmask & gpio.dir;
2758                 data &= ~(gpio.dmask & ~gpio.dir);
2759                 wr_reg32(info, IODR, data);
2760         }
2761         if (gpio.smask) {
2762                 data = rd_reg32(info, IOVR);
2763                 data |= gpio.smask & gpio.state;
2764                 data &= ~(gpio.smask & ~gpio.state);
2765                 wr_reg32(info, IOVR, data);
2766         }
2767         spin_unlock_irqrestore(&info->lock,flags);
2768
2769         return 0;
2770 }
2771
2772 /*
2773  * get general purpose IO pin state and direction
2774  */
2775 static int get_gpio(struct slgt_info *info, struct gpio_desc __user *user_gpio)
2776 {
2777         struct gpio_desc gpio;
2778         if (!info->gpio_present)
2779                 return -EINVAL;
2780         gpio.state = rd_reg32(info, IOVR);
2781         gpio.smask = 0xffffffff;
2782         gpio.dir   = rd_reg32(info, IODR);
2783         gpio.dmask = 0xffffffff;
2784         if (copy_to_user(user_gpio, &gpio, sizeof(gpio)))
2785                 return -EFAULT;
2786         DBGINFO(("%s get_gpio state=%08x dir=%08x\n",
2787                  info->device_name, gpio.state, gpio.dir));
2788         return 0;
2789 }
2790
2791 /*
2792  * conditional wait facility
2793  */
2794 static void init_cond_wait(struct cond_wait *w, unsigned int data)
2795 {
2796         init_waitqueue_head(&w->q);
2797         init_waitqueue_entry(&w->wait, current);
2798         w->data = data;
2799 }
2800
2801 static void add_cond_wait(struct cond_wait **head, struct cond_wait *w)
2802 {
2803         set_current_state(TASK_INTERRUPTIBLE);
2804         add_wait_queue(&w->q, &w->wait);
2805         w->next = *head;
2806         *head = w;
2807 }
2808
2809 static void remove_cond_wait(struct cond_wait **head, struct cond_wait *cw)
2810 {
2811         struct cond_wait *w, *prev;
2812         remove_wait_queue(&cw->q, &cw->wait);
2813         set_current_state(TASK_RUNNING);
2814         for (w = *head, prev = NULL ; w != NULL ; prev = w, w = w->next) {
2815                 if (w == cw) {
2816                         if (prev != NULL)
2817                                 prev->next = w->next;
2818                         else
2819                                 *head = w->next;
2820                         break;
2821                 }
2822         }
2823 }
2824
2825 static void flush_cond_wait(struct cond_wait **head)
2826 {
2827         while (*head != NULL) {
2828                 wake_up_interruptible(&(*head)->q);
2829                 *head = (*head)->next;
2830         }
2831 }
2832
2833 /*
2834  * wait for general purpose I/O pin(s) to enter specified state
2835  *
2836  * user_gpio fields:
2837  * state - bit indicates target pin state
2838  * smask - set bit indicates watched pin
2839  *
2840  * The wait ends when at least one watched pin enters the specified
2841  * state. When 0 (no error) is returned, user_gpio->state is set to the
2842  * state of all GPIO pins when the wait ends.
2843  *
2844  * Note: Each pin may be a dedicated input, dedicated output, or
2845  * configurable input/output. The number and configuration of pins
2846  * varies with the specific adapter model. Only input pins (dedicated
2847  * or configured) can be monitored with this function.
2848  */
2849 static int wait_gpio(struct slgt_info *info, struct gpio_desc __user *user_gpio)
2850 {
2851         unsigned long flags;
2852         int rc = 0;
2853         struct gpio_desc gpio;
2854         struct cond_wait wait;
2855         u32 state;
2856
2857         if (!info->gpio_present)
2858                 return -EINVAL;
2859         if (copy_from_user(&gpio, user_gpio, sizeof(gpio)))
2860                 return -EFAULT;
2861         DBGINFO(("%s wait_gpio() state=%08x smask=%08x\n",
2862                  info->device_name, gpio.state, gpio.smask));
2863         /* ignore output pins identified by set IODR bit */
2864         if ((gpio.smask &= ~rd_reg32(info, IODR)) == 0)
2865                 return -EINVAL;
2866         init_cond_wait(&wait, gpio.smask);
2867
2868         spin_lock_irqsave(&info->lock, flags);
2869         /* enable interrupts for watched pins */
2870         wr_reg32(info, IOER, rd_reg32(info, IOER) | gpio.smask);
2871         /* get current pin states */
2872         state = rd_reg32(info, IOVR);
2873
2874         if (gpio.smask & ~(state ^ gpio.state)) {
2875                 /* already in target state */
2876                 gpio.state = state;
2877         } else {
2878                 /* wait for target state */
2879                 add_cond_wait(&info->gpio_wait_q, &wait);
2880                 spin_unlock_irqrestore(&info->lock, flags);
2881                 schedule();
2882                 if (signal_pending(current))
2883                         rc = -ERESTARTSYS;
2884                 else
2885                         gpio.state = wait.data;
2886                 spin_lock_irqsave(&info->lock, flags);
2887                 remove_cond_wait(&info->gpio_wait_q, &wait);
2888         }
2889
2890         /* disable all GPIO interrupts if no waiting processes */
2891         if (info->gpio_wait_q == NULL)
2892                 wr_reg32(info, IOER, 0);
2893         spin_unlock_irqrestore(&info->lock,flags);
2894
2895         if ((rc == 0) && copy_to_user(user_gpio, &gpio, sizeof(gpio)))
2896                 rc = -EFAULT;
2897         return rc;
2898 }
2899
2900 static int modem_input_wait(struct slgt_info *info,int arg)
2901 {
2902         unsigned long flags;
2903         int rc;
2904         struct mgsl_icount cprev, cnow;
2905         DECLARE_WAITQUEUE(wait, current);
2906
2907         /* save current irq counts */
2908         spin_lock_irqsave(&info->lock,flags);
2909         cprev = info->icount;
2910         add_wait_queue(&info->status_event_wait_q, &wait);
2911         set_current_state(TASK_INTERRUPTIBLE);
2912         spin_unlock_irqrestore(&info->lock,flags);
2913
2914         for(;;) {
2915                 schedule();
2916                 if (signal_pending(current)) {
2917                         rc = -ERESTARTSYS;
2918                         break;
2919                 }
2920
2921                 /* get new irq counts */
2922                 spin_lock_irqsave(&info->lock,flags);
2923                 cnow = info->icount;
2924                 set_current_state(TASK_INTERRUPTIBLE);
2925                 spin_unlock_irqrestore(&info->lock,flags);
2926
2927                 /* if no change, wait aborted for some reason */
2928                 if (cnow.rng == cprev.rng && cnow.dsr == cprev.dsr &&
2929                     cnow.dcd == cprev.dcd && cnow.cts == cprev.cts) {
2930                         rc = -EIO;
2931                         break;
2932                 }
2933
2934                 /* check for change in caller specified modem input */
2935                 if ((arg & TIOCM_RNG && cnow.rng != cprev.rng) ||
2936                     (arg & TIOCM_DSR && cnow.dsr != cprev.dsr) ||
2937                     (arg & TIOCM_CD  && cnow.dcd != cprev.dcd) ||
2938                     (arg & TIOCM_CTS && cnow.cts != cprev.cts)) {
2939                         rc = 0;
2940                         break;
2941                 }
2942
2943                 cprev = cnow;
2944         }
2945         remove_wait_queue(&info->status_event_wait_q, &wait);
2946         set_current_state(TASK_RUNNING);
2947         return rc;
2948 }
2949
2950 /*
2951  *  return state of serial control and status signals
2952  */
2953 static int tiocmget(struct tty_struct *tty, struct file *file)
2954 {
2955         struct slgt_info *info = tty->driver_data;
2956         unsigned int result;
2957         unsigned long flags;
2958
2959         spin_lock_irqsave(&info->lock,flags);
2960         get_signals(info);
2961         spin_unlock_irqrestore(&info->lock,flags);
2962
2963         result = ((info->signals & SerialSignal_RTS) ? TIOCM_RTS:0) +
2964                 ((info->signals & SerialSignal_DTR) ? TIOCM_DTR:0) +
2965                 ((info->signals & SerialSignal_DCD) ? TIOCM_CAR:0) +
2966                 ((info->signals & SerialSignal_RI)  ? TIOCM_RNG:0) +
2967                 ((info->signals & SerialSignal_DSR) ? TIOCM_DSR:0) +
2968                 ((info->signals & SerialSignal_CTS) ? TIOCM_CTS:0);
2969
2970         DBGINFO(("%s tiocmget value=%08X\n", info->device_name, result));
2971         return result;
2972 }
2973
2974 /*
2975  * set modem control signals (DTR/RTS)
2976  *
2977  *      cmd     signal command: TIOCMBIS = set bit TIOCMBIC = clear bit
2978  *              TIOCMSET = set/clear signal values
2979  *      value   bit mask for command
2980  */
2981 static int tiocmset(struct tty_struct *tty, struct file *file,
2982                     unsigned int set, unsigned int clear)
2983 {
2984         struct slgt_info *info = tty->driver_data;
2985         unsigned long flags;
2986
2987         DBGINFO(("%s tiocmset(%x,%x)\n", info->device_name, set, clear));
2988
2989         if (set & TIOCM_RTS)
2990                 info->signals |= SerialSignal_RTS;
2991         if (set & TIOCM_DTR)
2992                 info->signals |= SerialSignal_DTR;
2993         if (clear & TIOCM_RTS)
2994                 info->signals &= ~SerialSignal_RTS;
2995         if (clear & TIOCM_DTR)
2996                 info->signals &= ~SerialSignal_DTR;
2997
2998         spin_lock_irqsave(&info->lock,flags);
2999         set_signals(info);
3000         spin_unlock_irqrestore(&info->lock,flags);
3001         return 0;
3002 }
3003
3004 /*
3005  *  block current process until the device is ready to open
3006  */
3007 static int block_til_ready(struct tty_struct *tty, struct file *filp,
3008                            struct slgt_info *info)
3009 {
3010         DECLARE_WAITQUEUE(wait, current);
3011         int             retval;
3012         int             do_clocal = 0, extra_count = 0;
3013         unsigned long   flags;
3014
3015         DBGINFO(("%s block_til_ready\n", tty->driver->name));
3016
3017         if (filp->f_flags & O_NONBLOCK || tty->flags & (1 << TTY_IO_ERROR)){
3018                 /* nonblock mode is set or port is not enabled */
3019                 info->flags |= ASYNC_NORMAL_ACTIVE;
3020                 return 0;
3021         }
3022
3023         if (tty->termios->c_cflag & CLOCAL)
3024                 do_clocal = 1;
3025
3026         /* Wait for carrier detect and the line to become
3027          * free (i.e., not in use by the callout).  While we are in
3028          * this loop, info->count is dropped by one, so that
3029          * close() knows when to free things.  We restore it upon
3030          * exit, either normal or abnormal.
3031          */
3032
3033         retval = 0;
3034         add_wait_queue(&info->open_wait, &wait);
3035
3036         spin_lock_irqsave(&info->lock, flags);
3037         if (!tty_hung_up_p(filp)) {
3038                 extra_count = 1;
3039                 info->count--;
3040         }
3041         spin_unlock_irqrestore(&info->lock, flags);
3042         info->blocked_open++;
3043
3044         while (1) {
3045                 if ((tty->termios->c_cflag & CBAUD)) {
3046                         spin_lock_irqsave(&info->lock,flags);
3047                         info->signals |= SerialSignal_RTS + SerialSignal_DTR;
3048                         set_signals(info);
3049                         spin_unlock_irqrestore(&info->lock,flags);
3050                 }
3051
3052                 set_current_state(TASK_INTERRUPTIBLE);
3053
3054                 if (tty_hung_up_p(filp) || !(info->flags & ASYNC_INITIALIZED)){
3055                         retval = (info->flags & ASYNC_HUP_NOTIFY) ?
3056                                         -EAGAIN : -ERESTARTSYS;
3057                         break;
3058                 }
3059
3060                 spin_lock_irqsave(&info->lock,flags);
3061                 get_signals(info);
3062                 spin_unlock_irqrestore(&info->lock,flags);
3063
3064                 if (!(info->flags & ASYNC_CLOSING) &&
3065                     (do_clocal || (info->signals & SerialSignal_DCD)) ) {
3066                         break;
3067                 }
3068
3069                 if (signal_pending(current)) {
3070                         retval = -ERESTARTSYS;
3071                         break;
3072                 }
3073
3074                 DBGINFO(("%s block_til_ready wait\n", tty->driver->name));
3075                 schedule();
3076         }
3077
3078         set_current_state(TASK_RUNNING);
3079         remove_wait_queue(&info->open_wait, &wait);
3080
3081         if (extra_count)
3082                 info->count++;
3083         info->blocked_open--;
3084
3085         if (!retval)
3086                 info->flags |= ASYNC_NORMAL_ACTIVE;
3087
3088         DBGINFO(("%s block_til_ready ready, rc=%d\n", tty->driver->name, retval));
3089         return retval;
3090 }
3091
3092 static int alloc_tmp_rbuf(struct slgt_info *info)
3093 {
3094         info->tmp_rbuf = kmalloc(info->max_frame_size + 5, GFP_KERNEL);
3095         if (info->tmp_rbuf == NULL)
3096                 return -ENOMEM;
3097         return 0;
3098 }
3099
3100 static void free_tmp_rbuf(struct slgt_info *info)
3101 {
3102         kfree(info->tmp_rbuf);
3103         info->tmp_rbuf = NULL;
3104 }
3105
3106 /*
3107  * allocate DMA descriptor lists.
3108  */
3109 static int alloc_desc(struct slgt_info *info)
3110 {
3111         unsigned int i;
3112         unsigned int pbufs;
3113
3114         /* allocate memory to hold descriptor lists */
3115         info->bufs = pci_alloc_consistent(info->pdev, DESC_LIST_SIZE, &info->bufs_dma_addr);
3116         if (info->bufs == NULL)
3117                 return -ENOMEM;
3118
3119         memset(info->bufs, 0, DESC_LIST_SIZE);
3120
3121         info->rbufs = (struct slgt_desc*)info->bufs;
3122         info->tbufs = ((struct slgt_desc*)info->bufs) + info->rbuf_count;
3123
3124         pbufs = (unsigned int)info->bufs_dma_addr;
3125
3126         /*
3127          * Build circular lists of descriptors
3128          */
3129
3130         for (i=0; i < info->rbuf_count; i++) {
3131                 /* physical address of this descriptor */
3132                 info->rbufs[i].pdesc = pbufs + (i * sizeof(struct slgt_desc));
3133
3134                 /* physical address of next descriptor */
3135                 if (i == info->rbuf_count - 1)
3136                         info->rbufs[i].next = cpu_to_le32(pbufs);
3137                 else
3138                         info->rbufs[i].next = cpu_to_le32(pbufs + ((i+1) * sizeof(struct slgt_desc)));
3139                 set_desc_count(info->rbufs[i], DMABUFSIZE);
3140         }
3141
3142         for (i=0; i < info->tbuf_count; i++) {
3143                 /* physical address of this descriptor */
3144                 info->tbufs[i].pdesc = pbufs + ((info->rbuf_count + i) * sizeof(struct slgt_desc));
3145
3146                 /* physical address of next descriptor */
3147                 if (i == info->tbuf_count - 1)
3148                         info->tbufs[i].next = cpu_to_le32(pbufs + info->rbuf_count * sizeof(struct slgt_desc));
3149                 else
3150                         info->tbufs[i].next = cpu_to_le32(pbufs + ((info->rbuf_count + i + 1) * sizeof(struct slgt_desc)));
3151         }
3152
3153         return 0;
3154 }
3155
3156 static void free_desc(struct slgt_info *info)
3157 {
3158         if (info->bufs != NULL) {
3159                 pci_free_consistent(info->pdev, DESC_LIST_SIZE, info->bufs, info->bufs_dma_addr);
3160                 info->bufs  = NULL;
3161                 info->rbufs = NULL;
3162                 info->tbufs = NULL;
3163         }
3164 }
3165
3166 static int alloc_bufs(struct slgt_info *info, struct slgt_desc *bufs, int count)
3167 {
3168         int i;
3169         for (i=0; i < count; i++) {
3170                 if ((bufs[i].buf = pci_alloc_consistent(info->pdev, DMABUFSIZE, &bufs[i].buf_dma_addr)) == NULL)
3171                         return -ENOMEM;
3172                 bufs[i].pbuf  = cpu_to_le32((unsigned int)bufs[i].buf_dma_addr);
3173         }
3174         return 0;
3175 }
3176
3177 static void free_bufs(struct slgt_info *info, struct slgt_desc *bufs, int count)
3178 {
3179         int i;
3180         for (i=0; i < count; i++) {
3181                 if (bufs[i].buf == NULL)
3182                         continue;
3183                 pci_free_consistent(info->pdev, DMABUFSIZE, bufs[i].buf, bufs[i].buf_dma_addr);
3184                 bufs[i].buf = NULL;
3185         }
3186 }
3187
3188 static int alloc_dma_bufs(struct slgt_info *info)
3189 {
3190         info->rbuf_count = 32;
3191         info->tbuf_count = 32;
3192
3193         if (alloc_desc(info) < 0 ||
3194             alloc_bufs(info, info->rbufs, info->rbuf_count) < 0 ||
3195             alloc_bufs(info, info->tbufs, info->tbuf_count) < 0 ||
3196             alloc_tmp_rbuf(info) < 0) {
3197                 DBGERR(("%s DMA buffer alloc fail\n", info->device_name));
3198                 return -ENOMEM;
3199         }
3200         reset_rbufs(info);
3201         return 0;
3202 }
3203
3204 static void free_dma_bufs(struct slgt_info *info)
3205 {
3206         if (info->bufs) {
3207                 free_bufs(info, info->rbufs, info->rbuf_count);
3208                 free_bufs(info, info->tbufs, info->tbuf_count);
3209                 free_desc(info);
3210         }
3211         free_tmp_rbuf(info);
3212 }
3213
3214 static int claim_resources(struct slgt_info *info)
3215 {
3216         if (request_mem_region(info->phys_reg_addr, SLGT_REG_SIZE, "synclink_gt") == NULL) {
3217                 DBGERR(("%s reg addr conflict, addr=%08X\n",
3218                         info->device_name, info->phys_reg_addr));
3219                 info->init_error = DiagStatus_AddressConflict;
3220                 goto errout;
3221         }
3222         else
3223                 info->reg_addr_requested = 1;
3224
3225         info->reg_addr = ioremap(info->phys_reg_addr, SLGT_REG_SIZE);
3226         if (!info->reg_addr) {
3227                 DBGERR(("%s cant map device registers, addr=%08X\n",
3228                         info->device_name, info->phys_reg_addr));
3229                 info->init_error = DiagStatus_CantAssignPciResources;
3230                 goto errout;
3231         }
3232         return 0;
3233
3234 errout:
3235         release_resources(info);
3236         return -ENODEV;
3237 }
3238
3239 static void release_resources(struct slgt_info *info)
3240 {
3241         if (info->irq_requested) {
3242                 free_irq(info->irq_level, info);
3243                 info->irq_requested = 0;
3244         }
3245
3246         if (info->reg_addr_requested) {
3247                 release_mem_region(info->phys_reg_addr, SLGT_REG_SIZE);
3248                 info->reg_addr_requested = 0;
3249         }
3250
3251         if (info->reg_addr) {
3252                 iounmap(info->reg_addr);
3253                 info->reg_addr = NULL;
3254         }
3255 }
3256
3257 /* Add the specified device instance data structure to the
3258  * global linked list of devices and increment the device count.
3259  */
3260 static void add_device(struct slgt_info *info)
3261 {
3262         char *devstr;
3263
3264         info->next_device = NULL;
3265         info->line = slgt_device_count;
3266         sprintf(info->device_name, "%s%d", tty_dev_prefix, info->line);
3267
3268         if (info->line < MAX_DEVICES) {
3269                 if (maxframe[info->line])
3270                         info->max_frame_size = maxframe[info->line];
3271                 info->dosyncppp = dosyncppp[info->line];
3272         }
3273
3274         slgt_device_count++;
3275
3276         if (!slgt_device_list)
3277                 slgt_device_list = info;
3278         else {
3279                 struct slgt_info *current_dev = slgt_device_list;
3280                 while(current_dev->next_device)
3281                         current_dev = current_dev->next_device;
3282                 current_dev->next_device = info;
3283         }
3284
3285         if (info->max_frame_size < 4096)
3286                 info->max_frame_size = 4096;
3287         else if (info->max_frame_size > 65535)
3288                 info->max_frame_size = 65535;
3289
3290         switch(info->pdev->device) {
3291         case SYNCLINK_GT_DEVICE_ID:
3292                 devstr = "GT";
3293                 break;
3294         case SYNCLINK_GT2_DEVICE_ID:
3295                 devstr = "GT2";
3296                 break;
3297         case SYNCLINK_GT4_DEVICE_ID:
3298                 devstr = "GT4";
3299                 break;
3300         case SYNCLINK_AC_DEVICE_ID:
3301                 devstr = "AC";
3302                 info->params.mode = MGSL_MODE_ASYNC;
3303                 break;
3304         default:
3305                 devstr = "(unknown model)";
3306         }
3307         printk("SyncLink %s %s IO=%08x IRQ=%d MaxFrameSize=%u\n",
3308                 devstr, info->device_name, info->phys_reg_addr,
3309                 info->irq_level, info->max_frame_size);
3310
3311 #if SYNCLINK_GENERIC_HDLC
3312         hdlcdev_init(info);
3313 #endif
3314 }
3315
3316 /*
3317  *  allocate device instance structure, return NULL on failure
3318  */
3319 static struct slgt_info *alloc_dev(int adapter_num, int port_num, struct pci_dev *pdev)
3320 {
3321         struct slgt_info *info;
3322
3323         info = kmalloc(sizeof(struct slgt_info), GFP_KERNEL);
3324
3325         if (!info) {
3326                 DBGERR(("%s device alloc failed adapter=%d port=%d\n",
3327                         driver_name, adapter_num, port_num));
3328         } else {
3329                 memset(info, 0, sizeof(struct slgt_info));
3330                 info->magic = MGSL_MAGIC;
3331                 INIT_WORK(&info->task, bh_handler);
3332                 info->max_frame_size = 4096;
3333                 info->raw_rx_size = DMABUFSIZE;
3334                 info->close_delay = 5*HZ/10;
3335                 info->closing_wait = 30*HZ;
3336                 init_waitqueue_head(&info->open_wait);
3337                 init_waitqueue_head(&info->close_wait);
3338                 init_waitqueue_head(&info->status_event_wait_q);
3339                 init_waitqueue_head(&info->event_wait_q);
3340                 spin_lock_init(&info->netlock);
3341                 memcpy(&info->params,&default_params,sizeof(MGSL_PARAMS));
3342                 info->idle_mode = HDLC_TXIDLE_FLAGS;
3343                 info->adapter_num = adapter_num;
3344                 info->port_num = port_num;
3345
3346                 init_timer(&info->tx_timer);
3347                 info->tx_timer.data = (unsigned long)info;
3348                 info->tx_timer.function = tx_timeout;
3349
3350                 init_timer(&info->rx_timer);
3351                 info->rx_timer.data = (unsigned long)info;
3352                 info->rx_timer.function = rx_timeout;
3353
3354                 /* Copy configuration info to device instance data */
3355                 info->pdev = pdev;
3356                 info->irq_level = pdev->irq;
3357                 info->phys_reg_addr = pci_resource_start(pdev,0);
3358
3359                 info->bus_type = MGSL_BUS_TYPE_PCI;
3360                 info->irq_flags = IRQF_SHARED;
3361
3362                 info->init_error = -1; /* assume error, set to 0 on successful init */
3363         }
3364
3365         return info;
3366 }
3367
3368 static void device_init(int adapter_num, struct pci_dev *pdev)
3369 {
3370         struct slgt_info *port_array[SLGT_MAX_PORTS];
3371         int i;
3372         int port_count = 1;
3373
3374         if (pdev->device == SYNCLINK_GT2_DEVICE_ID)
3375                 port_count = 2;
3376         else if (pdev->device == SYNCLINK_GT4_DEVICE_ID)
3377                 port_count = 4;
3378
3379         /* allocate device instances for all ports */
3380         for (i=0; i < port_count; ++i) {
3381                 port_array[i] = alloc_dev(adapter_num, i, pdev);
3382                 if (port_array[i] == NULL) {
3383                         for (--i; i >= 0; --i)
3384                                 kfree(port_array[i]);
3385                         return;
3386                 }
3387         }
3388
3389         /* give copy of port_array to all ports and add to device list  */
3390         for (i=0; i < port_count; ++i) {
3391                 memcpy(port_array[i]->port_array, port_array, sizeof(port_array));
3392                 add_device(port_array[i]);
3393                 port_array[i]->port_count = port_count;
3394                 spin_lock_init(&port_array[i]->lock);
3395         }
3396
3397         /* Allocate and claim adapter resources */
3398         if (!claim_resources(port_array[0])) {
3399
3400                 alloc_dma_bufs(port_array[0]);
3401
3402                 /* copy resource information from first port to others */
3403                 for (i = 1; i < port_count; ++i) {
3404                         port_array[i]->lock      = port_array[0]->lock;
3405                         port_array[i]->irq_level = port_array[0]->irq_level;
3406                         port_array[i]->reg_addr  = port_array[0]->reg_addr;
3407                         alloc_dma_bufs(port_array[i]);
3408                 }
3409
3410                 if (request_irq(port_array[0]->irq_level,
3411                                         slgt_interrupt,
3412                                         port_array[0]->irq_flags,
3413                                         port_array[0]->device_name,
3414                                         port_array[0]) < 0) {
3415                         DBGERR(("%s request_irq failed IRQ=%d\n",
3416                                 port_array[0]->device_name,
3417                                 port_array[0]->irq_level));
3418                 } else {
3419                         port_array[0]->irq_requested = 1;
3420                         adapter_test(port_array[0]);
3421                         for (i=1 ; i < port_count ; i++) {
3422                                 port_array[i]->init_error = port_array[0]->init_error;
3423                                 port_array[i]->gpio_present = port_array[0]->gpio_present;
3424                         }
3425                 }
3426         }
3427 }
3428
3429 static int __devinit init_one(struct pci_dev *dev,
3430                               const struct pci_device_id *ent)
3431 {
3432         if (pci_enable_device(dev)) {
3433                 printk("error enabling pci device %p\n", dev);
3434                 return -EIO;
3435         }
3436         pci_set_master(dev);
3437         device_init(slgt_device_count, dev);
3438         return 0;
3439 }
3440
3441 static void __devexit remove_one(struct pci_dev *dev)
3442 {
3443 }
3444
3445 static const struct tty_operations ops = {
3446         .open = open,
3447         .close = close,
3448         .write = write,
3449         .put_char = put_char,
3450         .flush_chars = flush_chars,
3451         .write_room = write_room,
3452         .chars_in_buffer = chars_in_buffer,
3453         .flush_buffer = flush_buffer,
3454         .ioctl = ioctl,
3455         .throttle = throttle,
3456         .unthrottle = unthrottle,
3457         .send_xchar = send_xchar,
3458         .break_ctl = set_break,
3459         .wait_until_sent = wait_until_sent,
3460         .read_proc = read_proc,
3461         .set_termios = set_termios,
3462         .stop = tx_hold,
3463         .start = tx_release,
3464         .hangup = hangup,
3465         .tiocmget = tiocmget,
3466         .tiocmset = tiocmset,
3467 };
3468
3469 static void slgt_cleanup(void)
3470 {
3471         int rc;
3472         struct slgt_info *info;
3473         struct slgt_info *tmp;
3474
3475         printk("unload %s %s\n", driver_name, driver_version);
3476
3477         if (serial_driver) {
3478                 if ((rc = tty_unregister_driver(serial_driver)))
3479                         DBGERR(("tty_unregister_driver error=%d\n", rc));
3480                 put_tty_driver(serial_driver);
3481         }
3482
3483         /* reset devices */
3484         info = slgt_device_list;
3485         while(info) {
3486                 reset_port(info);
3487                 info = info->next_device;
3488         }
3489
3490         /* release devices */
3491         info = slgt_device_list;
3492         while(info) {
3493 #if SYNCLINK_GENERIC_HDLC
3494                 hdlcdev_exit(info);
3495 #endif
3496                 free_dma_bufs(info);
3497                 free_tmp_rbuf(info);
3498                 if (info->port_num == 0)
3499                         release_resources(info);
3500                 tmp = info;
3501                 info = info->next_device;
3502                 kfree(tmp);
3503         }
3504
3505         if (pci_registered)
3506                 pci_unregister_driver(&pci_driver);
3507 }
3508
3509 /*
3510  *  Driver initialization entry point.
3511  */
3512 static int __init slgt_init(void)
3513 {
3514         int rc;
3515
3516         printk("%s %s\n", driver_name, driver_version);
3517
3518         slgt_device_count = 0;
3519         if ((rc = pci_register_driver(&pci_driver)) < 0) {
3520                 printk("%s pci_register_driver error=%d\n", driver_name, rc);
3521                 return rc;
3522         }
3523         pci_registered = 1;
3524
3525         if (!slgt_device_list) {
3526                 printk("%s no devices found\n",driver_name);
3527                 pci_unregister_driver(&pci_driver);
3528                 return -ENODEV;
3529         }
3530
3531         serial_driver = alloc_tty_driver(MAX_DEVICES);
3532         if (!serial_driver) {
3533                 rc = -ENOMEM;
3534                 goto error;
3535         }
3536
3537         /* Initialize the tty_driver structure */
3538
3539         serial_driver->owner = THIS_MODULE;
3540         serial_driver->driver_name = tty_driver_name;
3541         serial_driver->name = tty_dev_prefix;
3542         serial_driver->major = ttymajor;
3543         serial_driver->minor_start = 64;
3544         serial_driver->type = TTY_DRIVER_TYPE_SERIAL;
3545         serial_driver->subtype = SERIAL_TYPE_NORMAL;
3546         serial_driver->init_termios = tty_std_termios;
3547         serial_driver->init_termios.c_cflag =
3548                 B9600 | CS8 | CREAD | HUPCL | CLOCAL;
3549         serial_driver->init_termios.c_ispeed = 9600;
3550         serial_driver->init_termios.c_ospeed = 9600;
3551         serial_driver->flags = TTY_DRIVER_REAL_RAW;
3552         tty_set_operations(serial_driver, &ops);
3553         if ((rc = tty_register_driver(serial_driver)) < 0) {
3554                 DBGERR(("%s can't register serial driver\n", driver_name));
3555                 put_tty_driver(serial_driver);
3556                 serial_driver = NULL;
3557                 goto error;
3558         }
3559
3560         printk("%s %s, tty major#%d\n",
3561                 driver_name, driver_version,
3562                 serial_driver->major);
3563
3564         return 0;
3565
3566 error:
3567         slgt_cleanup();
3568         return rc;
3569 }
3570
3571 static void __exit slgt_exit(void)
3572 {
3573         slgt_cleanup();
3574 }
3575
3576 module_init(slgt_init);
3577 module_exit(slgt_exit);
3578
3579 /*
3580  * register access routines
3581  */
3582
3583 #define CALC_REGADDR() \
3584         unsigned long reg_addr = ((unsigned long)info->reg_addr) + addr; \
3585         if (addr >= 0x80) \
3586                 reg_addr += (info->port_num) * 32;
3587
3588 static __u8 rd_reg8(struct slgt_info *info, unsigned int addr)
3589 {
3590         CALC_REGADDR();
3591         return readb((void __iomem *)reg_addr);
3592 }
3593
3594 static void wr_reg8(struct slgt_info *info, unsigned int addr, __u8 value)
3595 {
3596         CALC_REGADDR();
3597         writeb(value, (void __iomem *)reg_addr);
3598 }
3599
3600 static __u16 rd_reg16(struct slgt_info *info, unsigned int addr)
3601 {
3602         CALC_REGADDR();
3603         return readw((void __iomem *)reg_addr);
3604 }
3605
3606 static void wr_reg16(struct slgt_info *info, unsigned int addr, __u16 value)
3607 {
3608         CALC_REGADDR();
3609         writew(value, (void __iomem *)reg_addr);
3610 }
3611
3612 static __u32 rd_reg32(struct slgt_info *info, unsigned int addr)
3613 {
3614         CALC_REGADDR();
3615         return readl((void __iomem *)reg_addr);
3616 }
3617
3618 static void wr_reg32(struct slgt_info *info, unsigned int addr, __u32 value)
3619 {
3620         CALC_REGADDR();
3621         writel(value, (void __iomem *)reg_addr);
3622 }
3623
3624 static void rdma_reset(struct slgt_info *info)
3625 {
3626         unsigned int i;
3627
3628         /* set reset bit */
3629         wr_reg32(info, RDCSR, BIT1);
3630
3631         /* wait for enable bit cleared */
3632         for(i=0 ; i < 1000 ; i++)
3633                 if (!(rd_reg32(info, RDCSR) & BIT0))
3634                         break;
3635 }
3636
3637 static void tdma_reset(struct slgt_info *info)
3638 {
3639         unsigned int i;
3640
3641         /* set reset bit */
3642         wr_reg32(info, TDCSR, BIT1);
3643
3644         /* wait for enable bit cleared */
3645         for(i=0 ; i < 1000 ; i++)
3646                 if (!(rd_reg32(info, TDCSR) & BIT0))
3647                         break;
3648 }
3649
3650 /*
3651  * enable internal loopback
3652  * TxCLK and RxCLK are generated from BRG
3653  * and TxD is looped back to RxD internally.
3654  */
3655 static void enable_loopback(struct slgt_info *info)
3656 {
3657         /* SCR (serial control) BIT2=looopback enable */
3658         wr_reg16(info, SCR, (unsigned short)(rd_reg16(info, SCR) | BIT2));
3659
3660         if (info->params.mode != MGSL_MODE_ASYNC) {
3661                 /* CCR (clock control)
3662                  * 07..05  tx clock source (010 = BRG)
3663                  * 04..02  rx clock source (010 = BRG)
3664                  * 01      auxclk enable   (0 = disable)
3665                  * 00      BRG enable      (1 = enable)
3666                  *
3667                  * 0100 1001
3668                  */
3669                 wr_reg8(info, CCR, 0x49);
3670
3671                 /* set speed if available, otherwise use default */
3672                 if (info->params.clock_speed)
3673                         set_rate(info, info->params.clock_speed);
3674                 else
3675                         set_rate(info, 3686400);
3676         }
3677 }
3678
3679 /*
3680  *  set baud rate generator to specified rate
3681  */
3682 static void set_rate(struct slgt_info *info, u32 rate)
3683 {
3684         unsigned int div;
3685         static unsigned int osc = 14745600;
3686
3687         /* div = osc/rate - 1
3688          *
3689          * Round div up if osc/rate is not integer to
3690          * force to next slowest rate.
3691          */
3692
3693         if (rate) {
3694                 div = osc/rate;
3695                 if (!(osc % rate) && div)
3696                         div--;
3697                 wr_reg16(info, BDR, (unsigned short)div);
3698         }
3699 }
3700
3701 static void rx_stop(struct slgt_info *info)
3702 {
3703         unsigned short val;
3704
3705         /* disable and reset receiver */
3706         val = rd_reg16(info, RCR) & ~BIT1;          /* clear enable bit */
3707         wr_reg16(info, RCR, (unsigned short)(val | BIT2)); /* set reset bit */
3708         wr_reg16(info, RCR, val);                  /* clear reset bit */
3709
3710         slgt_irq_off(info, IRQ_RXOVER + IRQ_RXDATA + IRQ_RXIDLE);
3711
3712         /* clear pending rx interrupts */
3713         wr_reg16(info, SSR, IRQ_RXIDLE + IRQ_RXOVER);
3714
3715         rdma_reset(info);
3716
3717         info->rx_enabled = 0;
3718         info->rx_restart = 0;
3719 }
3720
3721 static void rx_start(struct slgt_info *info)
3722 {
3723         unsigned short val;
3724
3725         slgt_irq_off(info, IRQ_RXOVER + IRQ_RXDATA);
3726
3727         /* clear pending rx overrun IRQ */
3728         wr_reg16(info, SSR, IRQ_RXOVER);
3729
3730         /* reset and disable receiver */
3731         val = rd_reg16(info, RCR) & ~BIT1; /* clear enable bit */
3732         wr_reg16(info, RCR, (unsigned short)(val | BIT2)); /* set reset bit */
3733         wr_reg16(info, RCR, val);                  /* clear reset bit */
3734
3735         rdma_reset(info);
3736         reset_rbufs(info);
3737
3738         /* set 1st descriptor address */
3739         wr_reg32(info, RDDAR, info->rbufs[0].pdesc);
3740
3741         if (info->params.mode != MGSL_MODE_ASYNC) {
3742                 /* enable rx DMA and DMA interrupt */
3743                 wr_reg32(info, RDCSR, (BIT2 + BIT0));
3744         } else {
3745                 /* enable saving of rx status, rx DMA and DMA interrupt */
3746                 wr_reg32(info, RDCSR, (BIT6 + BIT2 + BIT0));
3747         }
3748
3749         slgt_irq_on(info, IRQ_RXOVER);
3750
3751         /* enable receiver */
3752         wr_reg16(info, RCR, (unsigned short)(rd_reg16(info, RCR) | BIT1));
3753
3754         info->rx_restart = 0;
3755         info->rx_enabled = 1;
3756 }
3757
3758 static void tx_start(struct slgt_info *info)
3759 {
3760         if (!info->tx_enabled) {
3761                 wr_reg16(info, TCR,
3762                          (unsigned short)((rd_reg16(info, TCR) | BIT1) & ~BIT2));
3763                 info->tx_enabled = TRUE;
3764         }
3765
3766         if (info->tx_count) {
3767                 info->drop_rts_on_tx_done = 0;
3768
3769                 if (info->params.mode != MGSL_MODE_ASYNC) {
3770                         if (info->params.flags & HDLC_FLAG_AUTO_RTS) {
3771                                 get_signals(info);
3772                                 if (!(info->signals & SerialSignal_RTS)) {
3773                                         info->signals |= SerialSignal_RTS;
3774                                         set_signals(info);
3775                                         info->drop_rts_on_tx_done = 1;
3776                                 }
3777                         }
3778
3779                         slgt_irq_off(info, IRQ_TXDATA);
3780                         slgt_irq_on(info, IRQ_TXUNDER + IRQ_TXIDLE);
3781                         /* clear tx idle and underrun status bits */
3782                         wr_reg16(info, SSR, (unsigned short)(IRQ_TXIDLE + IRQ_TXUNDER));
3783
3784                         if (!(rd_reg32(info, TDCSR) & BIT0)) {
3785                                 /* tx DMA stopped, restart tx DMA */
3786                                 tdma_reset(info);
3787                                 /* set 1st descriptor address */
3788                                 wr_reg32(info, TDDAR, info->tbufs[info->tbuf_start].pdesc);
3789                                 switch(info->params.mode) {
3790                                 case MGSL_MODE_RAW:
3791                                 case MGSL_MODE_MONOSYNC:
3792                                 case MGSL_MODE_BISYNC:
3793                                         wr_reg32(info, TDCSR, BIT2 + BIT0); /* IRQ + DMA enable */
3794                                         break;
3795                                 default:
3796                                         wr_reg32(info, TDCSR, BIT0); /* DMA enable */
3797                                 }
3798                         }
3799
3800                         if (info->params.mode == MGSL_MODE_HDLC) {
3801                                 info->tx_timer.expires = jiffies + msecs_to_jiffies(5000);
3802                                 add_timer(&info->tx_timer);
3803                         }
3804                 } else {
3805                         tdma_reset(info);
3806                         /* set 1st descriptor address */
3807                         wr_reg32(info, TDDAR, info->tbufs[info->tbuf_start].pdesc);
3808
3809                         slgt_irq_off(info, IRQ_TXDATA);
3810                         slgt_irq_on(info, IRQ_TXIDLE);
3811                         /* clear tx idle status bit */
3812                         wr_reg16(info, SSR, IRQ_TXIDLE);
3813
3814                         /* enable tx DMA */
3815                         wr_reg32(info, TDCSR, BIT0);
3816                 }
3817
3818                 info->tx_active = 1;
3819         }
3820 }
3821
3822 static void tx_stop(struct slgt_info *info)
3823 {
3824         unsigned short val;
3825
3826         del_timer(&info->tx_timer);
3827
3828         tdma_reset(info);
3829
3830         /* reset and disable transmitter */
3831         val = rd_reg16(info, TCR) & ~BIT1;          /* clear enable bit */
3832         wr_reg16(info, TCR, (unsigned short)(val | BIT2)); /* set reset bit */
3833
3834         slgt_irq_off(info, IRQ_TXDATA + IRQ_TXIDLE + IRQ_TXUNDER);
3835
3836         /* clear tx idle and underrun status bit */
3837         wr_reg16(info, SSR, (unsigned short)(IRQ_TXIDLE + IRQ_TXUNDER));
3838
3839         reset_tbufs(info);
3840
3841         info->tx_enabled = 0;
3842         info->tx_active  = 0;
3843 }
3844
3845 static void reset_port(struct slgt_info *info)
3846 {
3847         if (!info->reg_addr)
3848                 return;
3849
3850         tx_stop(info);
3851         rx_stop(info);
3852
3853         info->signals &= ~(SerialSignal_DTR + SerialSignal_RTS);
3854         set_signals(info);
3855
3856         slgt_irq_off(info, IRQ_ALL | IRQ_MASTER);
3857 }
3858
3859 static void reset_adapter(struct slgt_info *info)
3860 {
3861         int i;
3862         for (i=0; i < info->port_count; ++i) {
3863                 if (info->port_array[i])
3864                         reset_port(info->port_array[i]);
3865         }
3866 }
3867
3868 static void async_mode(struct slgt_info *info)
3869 {
3870         unsigned short val;
3871
3872         slgt_irq_off(info, IRQ_ALL | IRQ_MASTER);
3873         tx_stop(info);
3874         rx_stop(info);
3875
3876         /* TCR (tx control)
3877          *
3878          * 15..13  mode, 010=async
3879          * 12..10  encoding, 000=NRZ
3880          * 09      parity enable
3881          * 08      1=odd parity, 0=even parity
3882          * 07      1=RTS driver control
3883          * 06      1=break enable
3884          * 05..04  character length
3885          *         00=5 bits
3886          *         01=6 bits
3887          *         10=7 bits
3888          *         11=8 bits
3889          * 03      0=1 stop bit, 1=2 stop bits
3890          * 02      reset
3891          * 01      enable
3892          * 00      auto-CTS enable
3893          */
3894         val = 0x4000;
3895
3896         if (info->if_mode & MGSL_INTERFACE_RTS_EN)
3897                 val |= BIT7;
3898
3899         if (info->params.parity != ASYNC_PARITY_NONE) {
3900                 val |= BIT9;
3901                 if (info->params.parity == ASYNC_PARITY_ODD)
3902                         val |= BIT8;
3903         }
3904
3905         switch (info->params.data_bits)
3906         {
3907         case 6: val |= BIT4; break;
3908         case 7: val |= BIT5; break;
3909         case 8: val |= BIT5 + BIT4; break;
3910         }
3911
3912         if (info->params.stop_bits != 1)
3913                 val |= BIT3;
3914
3915         if (info->params.flags & HDLC_FLAG_AUTO_CTS)
3916                 val |= BIT0;
3917
3918         wr_reg16(info, TCR, val);
3919
3920         /* RCR (rx control)
3921          *
3922          * 15..13  mode, 010=async
3923          * 12..10  encoding, 000=NRZ
3924          * 09      parity enable
3925          * 08      1=odd parity, 0=even parity
3926          * 07..06  reserved, must be 0
3927          * 05..04  character length
3928          *         00=5 bits
3929          *         01=6 bits
3930          *         10=7 bits
3931          *         11=8 bits
3932          * 03      reserved, must be zero
3933          * 02      reset
3934          * 01      enable
3935          * 00      auto-DCD enable
3936          */
3937         val = 0x4000;
3938
3939         if (info->params.parity != ASYNC_PARITY_NONE) {
3940                 val |= BIT9;
3941                 if (info->params.parity == ASYNC_PARITY_ODD)
3942                         val |= BIT8;
3943         }
3944
3945         switch (info->params.data_bits)
3946         {
3947         case 6: val |= BIT4; break;
3948         case 7: val |= BIT5; break;
3949         case 8: val |= BIT5 + BIT4; break;
3950         }
3951
3952         if (info->params.flags & HDLC_FLAG_AUTO_DCD)
3953                 val |= BIT0;
3954
3955         wr_reg16(info, RCR, val);
3956
3957         /* CCR (clock control)
3958          *
3959          * 07..05  011 = tx clock source is BRG/16
3960          * 04..02  010 = rx clock source is BRG
3961          * 01      0 = auxclk disabled
3962          * 00      1 = BRG enabled
3963          *
3964          * 0110 1001
3965          */
3966         wr_reg8(info, CCR, 0x69);
3967
3968         msc_set_vcr(info);
3969
3970         /* SCR (serial control)
3971          *
3972          * 15  1=tx req on FIFO half empty
3973          * 14  1=rx req on FIFO half full
3974          * 13  tx data  IRQ enable
3975          * 12  tx idle  IRQ enable
3976          * 11  rx break on IRQ enable
3977          * 10  rx data  IRQ enable
3978          * 09  rx break off IRQ enable
3979          * 08  overrun  IRQ enable
3980          * 07  DSR      IRQ enable
3981          * 06  CTS      IRQ enable
3982          * 05  DCD      IRQ enable
3983          * 04  RI       IRQ enable
3984          * 03  reserved, must be zero
3985          * 02  1=txd->rxd internal loopback enable
3986          * 01  reserved, must be zero
3987          * 00  1=master IRQ enable
3988          */
3989         val = BIT15 + BIT14 + BIT0;
3990         wr_reg16(info, SCR, val);
3991
3992         slgt_irq_on(info, IRQ_RXBREAK | IRQ_RXOVER);
3993
3994         set_rate(info, info->params.data_rate * 16);
3995
3996         if (info->params.loopback)
3997                 enable_loopback(info);
3998 }
3999
4000 static void sync_mode(struct slgt_info *info)
4001 {
4002         unsigned short val;
4003
4004         slgt_irq_off(info, IRQ_ALL | IRQ_MASTER);
4005         tx_stop(info);
4006         rx_stop(info);
4007
4008         /* TCR (tx control)
4009          *
4010          * 15..13  mode, 000=HDLC 001=raw 010=async 011=monosync 100=bisync
4011          * 12..10  encoding
4012          * 09      CRC enable
4013          * 08      CRC32
4014          * 07      1=RTS driver control
4015          * 06      preamble enable
4016          * 05..04  preamble length
4017          * 03      share open/close flag
4018          * 02      reset
4019          * 01      enable
4020          * 00      auto-CTS enable
4021          */
4022         val = 0;
4023
4024         switch(info->params.mode) {
4025         case MGSL_MODE_MONOSYNC: val |= BIT14 + BIT13; break;
4026         case MGSL_MODE_BISYNC:   val |= BIT15; break;
4027         case MGSL_MODE_RAW:      val |= BIT13; break;
4028         }
4029         if (info->if_mode & MGSL_INTERFACE_RTS_EN)
4030                 val |= BIT7;
4031
4032         switch(info->params.encoding)
4033         {
4034         case HDLC_ENCODING_NRZB:          val |= BIT10; break;
4035         case HDLC_ENCODING_NRZI_MARK:     val |= BIT11; break;
4036         case HDLC_ENCODING_NRZI:          val |= BIT11 + BIT10; break;
4037         case HDLC_ENCODING_BIPHASE_MARK:  val |= BIT12; break;
4038         case HDLC_ENCODING_BIPHASE_SPACE: val |= BIT12 + BIT10; break;
4039         case HDLC_ENCODING_BIPHASE_LEVEL: val |= BIT12 + BIT11; break;
4040         case HDLC_ENCODING_DIFF_BIPHASE_LEVEL: val |= BIT12 + BIT11 + BIT10; break;
4041         }
4042
4043         switch (info->params.crc_type & HDLC_CRC_MASK)
4044         {
4045         case HDLC_CRC_16_CCITT: val |= BIT9; break;
4046         case HDLC_CRC_32_CCITT: val |= BIT9 + BIT8; break;
4047         }
4048
4049         if (info->params.preamble != HDLC_PREAMBLE_PATTERN_NONE)
4050                 val |= BIT6;
4051
4052         switch (info->params.preamble_length)
4053         {
4054         case HDLC_PREAMBLE_LENGTH_16BITS: val |= BIT5; break;
4055         case HDLC_PREAMBLE_LENGTH_32BITS: val |= BIT4; break;
4056         case HDLC_PREAMBLE_LENGTH_64BITS: val |= BIT5 + BIT4; break;
4057         }
4058
4059         if (info->params.flags & HDLC_FLAG_AUTO_CTS)
4060                 val |= BIT0;
4061
4062         wr_reg16(info, TCR, val);
4063
4064         /* TPR (transmit preamble) */
4065
4066         switch (info->params.preamble)
4067         {
4068         case HDLC_PREAMBLE_PATTERN_FLAGS: val = 0x7e; break;
4069         case HDLC_PREAMBLE_PATTERN_ONES:  val = 0xff; break;
4070         case HDLC_PREAMBLE_PATTERN_ZEROS: val = 0x00; break;
4071         case HDLC_PREAMBLE_PATTERN_10:    val = 0x55; break;
4072         case HDLC_PREAMBLE_PATTERN_01:    val = 0xaa; break;
4073         default:                          val = 0x7e; break;
4074         }
4075         wr_reg8(info, TPR, (unsigned char)val);
4076
4077         /* RCR (rx control)
4078          *
4079          * 15..13  mode, 000=HDLC 001=raw 010=async 011=monosync 100=bisync
4080          * 12..10  encoding
4081          * 09      CRC enable
4082          * 08      CRC32
4083          * 07..03  reserved, must be 0
4084          * 02      reset
4085          * 01      enable
4086          * 00      auto-DCD enable
4087          */
4088         val = 0;
4089
4090         switch(info->params.mode) {
4091         case MGSL_MODE_MONOSYNC: val |= BIT14 + BIT13; break;
4092         case MGSL_MODE_BISYNC:   val |= BIT15; break;
4093         case MGSL_MODE_RAW:      val |= BIT13; break;
4094         }
4095
4096         switch(info->params.encoding)
4097         {
4098         case HDLC_ENCODING_NRZB:          val |= BIT10; break;
4099         case HDLC_ENCODING_NRZI_MARK:     val |= BIT11; break;
4100         case HDLC_ENCODING_NRZI:          val |= BIT11 + BIT10; break;
4101         case HDLC_ENCODING_BIPHASE_MARK:  val |= BIT12; break;
4102         case HDLC_ENCODING_BIPHASE_SPACE: val |= BIT12 + BIT10; break;
4103         case HDLC_ENCODING_BIPHASE_LEVEL: val |= BIT12 + BIT11; break;
4104         case HDLC_ENCODING_DIFF_BIPHASE_LEVEL: val |= BIT12 + BIT11 + BIT10; break;
4105         }
4106
4107         switch (info->params.crc_type & HDLC_CRC_MASK)
4108         {
4109         case HDLC_CRC_16_CCITT: val |= BIT9; break;
4110         case HDLC_CRC_32_CCITT: val |= BIT9 + BIT8; break;
4111         }
4112
4113         if (info->params.flags & HDLC_FLAG_AUTO_DCD)
4114                 val |= BIT0;
4115
4116         wr_reg16(info, RCR, val);
4117
4118         /* CCR (clock control)
4119          *
4120          * 07..05  tx clock source
4121          * 04..02  rx clock source
4122          * 01      auxclk enable
4123          * 00      BRG enable
4124          */
4125         val = 0;
4126
4127         if (info->params.flags & HDLC_FLAG_TXC_BRG)
4128         {
4129                 // when RxC source is DPLL, BRG generates 16X DPLL
4130                 // reference clock, so take TxC from BRG/16 to get
4131                 // transmit clock at actual data rate
4132                 if (info->params.flags & HDLC_FLAG_RXC_DPLL)
4133                         val |= BIT6 + BIT5;     /* 011, txclk = BRG/16 */
4134                 else
4135                         val |= BIT6;    /* 010, txclk = BRG */
4136         }
4137         else if (info->params.flags & HDLC_FLAG_TXC_DPLL)
4138                 val |= BIT7;    /* 100, txclk = DPLL Input */
4139         else if (info->params.flags & HDLC_FLAG_TXC_RXCPIN)
4140                 val |= BIT5;    /* 001, txclk = RXC Input */
4141
4142         if (info->params.flags & HDLC_FLAG_RXC_BRG)
4143                 val |= BIT3;    /* 010, rxclk = BRG */
4144         else if (info->params.flags & HDLC_FLAG_RXC_DPLL)
4145                 val |= BIT4;    /* 100, rxclk = DPLL */
4146         else if (info->params.flags & HDLC_FLAG_RXC_TXCPIN)
4147                 val |= BIT2;    /* 001, rxclk = TXC Input */
4148
4149         if (info->params.clock_speed)
4150                 val |= BIT1 + BIT0;
4151
4152         wr_reg8(info, CCR, (unsigned char)val);
4153
4154         if (info->params.flags & (HDLC_FLAG_TXC_DPLL + HDLC_FLAG_RXC_DPLL))
4155         {
4156                 // program DPLL mode
4157                 switch(info->params.encoding)
4158                 {
4159                 case HDLC_ENCODING_BIPHASE_MARK:
4160                 case HDLC_ENCODING_BIPHASE_SPACE:
4161                         val = BIT7; break;
4162                 case HDLC_ENCODING_BIPHASE_LEVEL:
4163                 case HDLC_ENCODING_DIFF_BIPHASE_LEVEL:
4164                         val = BIT7 + BIT6; break;
4165                 default: val = BIT6;    // NRZ encodings
4166                 }
4167                 wr_reg16(info, RCR, (unsigned short)(rd_reg16(info, RCR) | val));
4168
4169                 // DPLL requires a 16X reference clock from BRG
4170                 set_rate(info, info->params.clock_speed * 16);
4171         }
4172         else
4173                 set_rate(info, info->params.clock_speed);
4174
4175         tx_set_idle(info);
4176
4177         msc_set_vcr(info);
4178
4179         /* SCR (serial control)
4180          *
4181          * 15  1=tx req on FIFO half empty
4182          * 14  1=rx req on FIFO half full
4183          * 13  tx data  IRQ enable
4184          * 12  tx idle  IRQ enable
4185          * 11  underrun IRQ enable
4186          * 10  rx data  IRQ enable
4187          * 09  rx idle  IRQ enable
4188          * 08  overrun  IRQ enable
4189          * 07  DSR      IRQ enable
4190          * 06  CTS      IRQ enable
4191          * 05  DCD      IRQ enable
4192          * 04  RI       IRQ enable
4193          * 03  reserved, must be zero
4194          * 02  1=txd->rxd internal loopback enable
4195          * 01  reserved, must be zero
4196          * 00  1=master IRQ enable
4197          */
4198         wr_reg16(info, SCR, BIT15 + BIT14 + BIT0);
4199
4200         if (info->params.loopback)
4201                 enable_loopback(info);
4202 }
4203
4204 /*
4205  *  set transmit idle mode
4206  */
4207 static void tx_set_idle(struct slgt_info *info)
4208 {
4209         unsigned char val;
4210         unsigned short tcr;
4211
4212         /* if preamble enabled (tcr[6] == 1) then tx idle size = 8 bits
4213          * else tcr[5:4] = tx idle size: 00 = 8 bits, 01 = 16 bits
4214          */
4215         tcr = rd_reg16(info, TCR);
4216         if (info->idle_mode & HDLC_TXIDLE_CUSTOM_16) {
4217                 /* disable preamble, set idle size to 16 bits */
4218                 tcr = (tcr & ~(BIT6 + BIT5)) | BIT4;
4219                 /* MSB of 16 bit idle specified in tx preamble register (TPR) */
4220                 wr_reg8(info, TPR, (unsigned char)((info->idle_mode >> 8) & 0xff));
4221         } else if (!(tcr & BIT6)) {
4222                 /* preamble is disabled, set idle size to 8 bits */
4223                 tcr &= ~(BIT5 + BIT4);
4224         }
4225         wr_reg16(info, TCR, tcr);
4226
4227         if (info->idle_mode & (HDLC_TXIDLE_CUSTOM_8 | HDLC_TXIDLE_CUSTOM_16)) {
4228                 /* LSB of custom tx idle specified in tx idle register */
4229                 val = (unsigned char)(info->idle_mode & 0xff);
4230         } else {
4231                 /* standard 8 bit idle patterns */
4232                 switch(info->idle_mode)
4233                 {
4234                 case HDLC_TXIDLE_FLAGS:          val = 0x7e; break;
4235                 case HDLC_TXIDLE_ALT_ZEROS_ONES:
4236                 case HDLC_TXIDLE_ALT_MARK_SPACE: val = 0xaa; break;
4237                 case HDLC_TXIDLE_ZEROS:
4238                 case HDLC_TXIDLE_SPACE:          val = 0x00; break;
4239                 default:                         val = 0xff;
4240                 }
4241         }
4242
4243         wr_reg8(info, TIR, val);
4244 }
4245
4246 /*
4247  * get state of V24 status (input) signals
4248  */
4249 static void get_signals(struct slgt_info *info)
4250 {
4251         unsigned short status = rd_reg16(info, SSR);
4252
4253         /* clear all serial signals except DTR and RTS */
4254         info->signals &= SerialSignal_DTR + SerialSignal_RTS;
4255
4256         if (status & BIT3)
4257                 info->signals |= SerialSignal_DSR;
4258         if (status & BIT2)
4259                 info->signals |= SerialSignal_CTS;
4260         if (status & BIT1)
4261                 info->signals |= SerialSignal_DCD;
4262         if (status & BIT0)
4263                 info->signals |= SerialSignal_RI;
4264 }
4265
4266 /*
4267  * set V.24 Control Register based on current configuration
4268  */
4269 static void msc_set_vcr(struct slgt_info *info)
4270 {
4271         unsigned char val = 0;
4272
4273         /* VCR (V.24 control)
4274          *
4275          * 07..04  serial IF select
4276          * 03      DTR
4277          * 02      RTS
4278          * 01      LL
4279          * 00      RL
4280          */
4281
4282         switch(info->if_mode & MGSL_INTERFACE_MASK)
4283         {
4284         case MGSL_INTERFACE_RS232:
4285                 val |= BIT5; /* 0010 */
4286                 break;
4287         case MGSL_INTERFACE_V35:
4288                 val |= BIT7 + BIT6 + BIT5; /* 1110 */
4289                 break;
4290         case MGSL_INTERFACE_RS422:
4291                 val |= BIT6; /* 0100 */
4292                 break;
4293         }
4294
4295         if (info->signals & SerialSignal_DTR)
4296                 val |= BIT3;
4297         if (info->signals & SerialSignal_RTS)
4298                 val |= BIT2;
4299         if (info->if_mode & MGSL_INTERFACE_LL)
4300                 val |= BIT1;
4301         if (info->if_mode & MGSL_INTERFACE_RL)
4302                 val |= BIT0;
4303         wr_reg8(info, VCR, val);
4304 }
4305
4306 /*
4307  * set state of V24 control (output) signals
4308  */
4309 static void set_signals(struct slgt_info *info)
4310 {
4311         unsigned char val = rd_reg8(info, VCR);
4312         if (info->signals & SerialSignal_DTR)
4313                 val |= BIT3;
4314         else
4315                 val &= ~BIT3;
4316         if (info->signals & SerialSignal_RTS)
4317                 val |= BIT2;
4318         else
4319                 val &= ~BIT2;
4320         wr_reg8(info, VCR, val);
4321 }
4322
4323 /*
4324  * free range of receive DMA buffers (i to last)
4325  */
4326 static void free_rbufs(struct slgt_info *info, unsigned int i, unsigned int last)
4327 {
4328         int done = 0;
4329
4330         while(!done) {
4331                 /* reset current buffer for reuse */
4332                 info->rbufs[i].status = 0;
4333                 switch(info->params.mode) {
4334                 case MGSL_MODE_RAW:
4335                 case MGSL_MODE_MONOSYNC:
4336                 case MGSL_MODE_BISYNC:
4337                         set_desc_count(info->rbufs[i], info->raw_rx_size);
4338                         break;
4339                 default:
4340                         set_desc_count(info->rbufs[i], DMABUFSIZE);
4341                 }
4342
4343                 if (i == last)
4344                         done = 1;
4345                 if (++i == info->rbuf_count)
4346                         i = 0;
4347         }
4348         info->rbuf_current = i;
4349 }
4350
4351 /*
4352  * mark all receive DMA buffers as free
4353  */
4354 static void reset_rbufs(struct slgt_info *info)
4355 {
4356         free_rbufs(info, 0, info->rbuf_count - 1);
4357 }
4358
4359 /*
4360  * pass receive HDLC frame to upper layer
4361  *
4362  * return 1 if frame available, otherwise 0
4363  */
4364 static int rx_get_frame(struct slgt_info *info)
4365 {
4366         unsigned int start, end;
4367         unsigned short status;
4368         unsigned int framesize = 0;
4369         int rc = 0;
4370         unsigned long flags;
4371         struct tty_struct *tty = info->tty;
4372         unsigned char addr_field = 0xff;
4373         unsigned int crc_size = 0;
4374
4375         switch (info->params.crc_type & HDLC_CRC_MASK) {
4376         case HDLC_CRC_16_CCITT: crc_size = 2; break;
4377         case HDLC_CRC_32_CCITT: crc_size = 4; break;
4378         }
4379
4380 check_again:
4381
4382         framesize = 0;
4383         addr_field = 0xff;
4384         start = end = info->rbuf_current;
4385
4386         for (;;) {
4387                 if (!desc_complete(info->rbufs[end]))
4388                         goto cleanup;
4389
4390                 if (framesize == 0 && info->params.addr_filter != 0xff)
4391                         addr_field = info->rbufs[end].buf[0];
4392
4393                 framesize += desc_count(info->rbufs[end]);
4394
4395                 if (desc_eof(info->rbufs[end]))
4396                         break;
4397
4398                 if (++end == info->rbuf_count)
4399                         end = 0;
4400
4401                 if (end == info->rbuf_current) {
4402                         if (info->rx_enabled){
4403                                 spin_lock_irqsave(&info->lock,flags);
4404                                 rx_start(info);
4405                                 spin_unlock_irqrestore(&info->lock,flags);
4406                         }
4407                         goto cleanup;
4408                 }
4409         }
4410
4411         /* status
4412          *
4413          * 15      buffer complete
4414          * 14..06  reserved
4415          * 05..04  residue
4416          * 02      eof (end of frame)
4417          * 01      CRC error
4418          * 00      abort
4419          */
4420         status = desc_status(info->rbufs[end]);
4421
4422         /* ignore CRC bit if not using CRC (bit is undefined) */
4423         if ((info->params.crc_type & HDLC_CRC_MASK) == HDLC_CRC_NONE)
4424                 status &= ~BIT1;
4425
4426         if (framesize == 0 ||
4427                  (addr_field != 0xff && addr_field != info->params.addr_filter)) {
4428                 free_rbufs(info, start, end);
4429                 goto check_again;
4430         }
4431
4432         if (framesize < (2 + crc_size) || status & BIT0) {
4433                 info->icount.rxshort++;
4434                 framesize = 0;
4435         } else if (status & BIT1) {
4436                 info->icount.rxcrc++;
4437                 if (!(info->params.crc_type & HDLC_CRC_RETURN_EX))
4438                         framesize = 0;
4439         }
4440
4441 #if SYNCLINK_GENERIC_HDLC
4442         if (framesize == 0) {
4443                 struct net_device_stats *stats = hdlc_stats(info->netdev);
4444                 stats->rx_errors++;
4445                 stats->rx_frame_errors++;
4446         }
4447 #endif
4448
4449         DBGBH(("%s rx frame status=%04X size=%d\n",
4450                 info->device_name, status, framesize));
4451         DBGDATA(info, info->rbufs[start].buf, min_t(int, framesize, DMABUFSIZE), "rx");
4452
4453         if (framesize) {
4454                 if (!(info->params.crc_type & HDLC_CRC_RETURN_EX)) {
4455                         framesize -= crc_size;
4456                         crc_size = 0;
4457                 }
4458
4459                 if (framesize > info->max_frame_size + crc_size)
4460                         info->icount.rxlong++;
4461                 else {
4462                         /* copy dma buffer(s) to contiguous temp buffer */
4463                         int copy_count = framesize;
4464                         int i = start;
4465                         unsigned char *p = info->tmp_rbuf;
4466                         info->tmp_rbuf_count = framesize;
4467
4468                         info->icount.rxok++;
4469
4470                         while(copy_count) {
4471                                 int partial_count = min(copy_count, DMABUFSIZE);
4472                                 memcpy(p, info->rbufs[i].buf, partial_count);
4473                                 p += partial_count;
4474                                 copy_count -= partial_count;
4475                                 if (++i == info->rbuf_count)
4476                                         i = 0;
4477                         }
4478
4479                         if (info->params.crc_type & HDLC_CRC_RETURN_EX) {
4480                                 *p = (status & BIT1) ? RX_CRC_ERROR : RX_OK;
4481                                 framesize++;
4482                         }
4483
4484 #if SYNCLINK_GENERIC_HDLC
4485                         if (info->netcount)
4486                                 hdlcdev_rx(info,info->tmp_rbuf, framesize);
4487                         else
4488 #endif
4489                                 ldisc_receive_buf(tty, info->tmp_rbuf, info->flag_buf, framesize);
4490                 }
4491         }
4492         free_rbufs(info, start, end);
4493         rc = 1;
4494
4495 cleanup:
4496         return rc;
4497 }
4498
4499 /*
4500  * pass receive buffer (RAW synchronous mode) to tty layer
4501  * return 1 if buffer available, otherwise 0
4502  */
4503 static int rx_get_buf(struct slgt_info *info)
4504 {
4505         unsigned int i = info->rbuf_current;
4506         unsigned int count;
4507
4508         if (!desc_complete(info->rbufs[i]))
4509                 return 0;
4510         count = desc_count(info->rbufs[i]);
4511         switch(info->params.mode) {
4512         case MGSL_MODE_MONOSYNC:
4513         case MGSL_MODE_BISYNC:
4514                 /* ignore residue in byte synchronous modes */
4515                 if (desc_residue(info->rbufs[i]))
4516                         count--;
4517                 break;
4518         }
4519         DBGDATA(info, info->rbufs[i].buf, count, "rx");
4520         DBGINFO(("rx_get_buf size=%d\n", count));
4521         if (count)
4522                 ldisc_receive_buf(info->tty, info->rbufs[i].buf,
4523                                   info->flag_buf, count);
4524         free_rbufs(info, i, i);
4525         return 1;
4526 }
4527
4528 static void reset_tbufs(struct slgt_info *info)
4529 {
4530         unsigned int i;
4531         info->tbuf_current = 0;
4532         for (i=0 ; i < info->tbuf_count ; i++) {
4533                 info->tbufs[i].status = 0;
4534                 info->tbufs[i].count  = 0;
4535         }
4536 }
4537
4538 /*
4539  * return number of free transmit DMA buffers
4540  */
4541 static unsigned int free_tbuf_count(struct slgt_info *info)
4542 {
4543         unsigned int count = 0;
4544         unsigned int i = info->tbuf_current;
4545
4546         do
4547         {
4548                 if (desc_count(info->tbufs[i]))
4549                         break; /* buffer in use */
4550                 ++count;
4551                 if (++i == info->tbuf_count)
4552                         i=0;
4553         } while (i != info->tbuf_current);
4554
4555         /* last buffer with zero count may be in use, assume it is */
4556         if (count)
4557                 --count;
4558
4559         return count;
4560 }
4561
4562 /*
4563  * load transmit DMA buffer(s) with data
4564  */
4565 static void tx_load(struct slgt_info *info, const char *buf, unsigned int size)
4566 {
4567         unsigned short count;
4568         unsigned int i;
4569         struct slgt_desc *d;
4570
4571         if (size == 0)
4572                 return;
4573
4574         DBGDATA(info, buf, size, "tx");
4575
4576         info->tbuf_start = i = info->tbuf_current;
4577
4578         while (size) {
4579                 d = &info->tbufs[i];
4580                 if (++i == info->tbuf_count)
4581                         i = 0;
4582
4583                 count = (unsigned short)((size > DMABUFSIZE) ? DMABUFSIZE : size);
4584                 memcpy(d->buf, buf, count);
4585
4586                 size -= count;
4587                 buf  += count;
4588
4589                 /*
4590                  * set EOF bit for last buffer of HDLC frame or
4591                  * for every buffer in raw mode
4592                  */
4593                 if ((!size && info->params.mode == MGSL_MODE_HDLC) ||
4594                     info->params.mode == MGSL_MODE_RAW)
4595                         set_desc_eof(*d, 1);
4596                 else
4597                         set_desc_eof(*d, 0);
4598
4599                 set_desc_count(*d, count);
4600         }
4601
4602         info->tbuf_current = i;
4603 }
4604
4605 static int register_test(struct slgt_info *info)
4606 {
4607         static unsigned short patterns[] =
4608                 {0x0000, 0xffff, 0xaaaa, 0x5555, 0x6969, 0x9696};
4609         static unsigned int count = sizeof(patterns)/sizeof(patterns[0]);
4610         unsigned int i;
4611         int rc = 0;
4612
4613         for (i=0 ; i < count ; i++) {
4614                 wr_reg16(info, TIR, patterns[i]);
4615                 wr_reg16(info, BDR, patterns[(i+1)%count]);
4616                 if ((rd_reg16(info, TIR) != patterns[i]) ||
4617                     (rd_reg16(info, BDR) != patterns[(i+1)%count])) {
4618                         rc = -ENODEV;
4619                         break;
4620                 }
4621         }
4622         info->gpio_present = (rd_reg32(info, JCR) & BIT5) ? 1 : 0;
4623         info->init_error = rc ? 0 : DiagStatus_AddressFailure;
4624         return rc;
4625 }
4626
4627 static int irq_test(struct slgt_info *info)
4628 {
4629         unsigned long timeout;
4630         unsigned long flags;
4631         struct tty_struct *oldtty = info->tty;
4632         u32 speed = info->params.data_rate;
4633
4634         info->params.data_rate = 921600;
4635         info->tty = NULL;
4636
4637         spin_lock_irqsave(&info->lock, flags);
4638         async_mode(info);
4639         slgt_irq_on(info, IRQ_TXIDLE);
4640
4641         /* enable transmitter */
4642         wr_reg16(info, TCR,
4643                 (unsigned short)(rd_reg16(info, TCR) | BIT1));
4644
4645         /* write one byte and wait for tx idle */
4646         wr_reg16(info, TDR, 0);
4647
4648         /* assume failure */
4649         info->init_error = DiagStatus_IrqFailure;
4650         info->irq_occurred = FALSE;
4651
4652         spin_unlock_irqrestore(&info->lock, flags);
4653
4654         timeout=100;
4655         while(timeout-- && !info->irq_occurred)
4656                 msleep_interruptible(10);
4657
4658         spin_lock_irqsave(&info->lock,flags);
4659         reset_port(info);
4660         spin_unlock_irqrestore(&info->lock,flags);
4661
4662         info->params.data_rate = speed;
4663         info->tty = oldtty;
4664
4665         info->init_error = info->irq_occurred ? 0 : DiagStatus_IrqFailure;
4666         return info->irq_occurred ? 0 : -ENODEV;
4667 }
4668
4669 static int loopback_test_rx(struct slgt_info *info)
4670 {
4671         unsigned char *src, *dest;
4672         int count;
4673
4674         if (desc_complete(info->rbufs[0])) {
4675                 count = desc_count(info->rbufs[0]);
4676                 src   = info->rbufs[0].buf;
4677                 dest  = info->tmp_rbuf;
4678
4679                 for( ; count ; count-=2, src+=2) {
4680                         /* src=data byte (src+1)=status byte */
4681                         if (!(*(src+1) & (BIT9 + BIT8))) {
4682                                 *dest = *src;
4683                                 dest++;
4684                                 info->tmp_rbuf_count++;
4685                         }
4686                 }
4687                 DBGDATA(info, info->tmp_rbuf, info->tmp_rbuf_count, "rx");
4688                 return 1;
4689         }
4690         return 0;
4691 }
4692
4693 static int loopback_test(struct slgt_info *info)
4694 {
4695 #define TESTFRAMESIZE 20
4696
4697         unsigned long timeout;
4698         u16 count = TESTFRAMESIZE;
4699         unsigned char buf[TESTFRAMESIZE];
4700         int rc = -ENODEV;
4701         unsigned long flags;
4702
4703         struct tty_struct *oldtty = info->tty;
4704         MGSL_PARAMS params;
4705
4706         memcpy(&params, &info->params, sizeof(params));
4707
4708         info->params.mode = MGSL_MODE_ASYNC;
4709         info->params.data_rate = 921600;
4710         info->params.loopback = 1;
4711         info->tty = NULL;
4712
4713         /* build and send transmit frame */
4714         for (count = 0; count < TESTFRAMESIZE; ++count)
4715                 buf[count] = (unsigned char)count;
4716
4717         info->tmp_rbuf_count = 0;
4718         memset(info->tmp_rbuf, 0, TESTFRAMESIZE);
4719
4720         /* program hardware for HDLC and enabled receiver */
4721         spin_lock_irqsave(&info->lock,flags);
4722         async_mode(info);
4723         rx_start(info);
4724         info->tx_count = count;
4725         tx_load(info, buf, count);
4726         tx_start(info);
4727         spin_unlock_irqrestore(&info->lock, flags);
4728
4729         /* wait for receive complete */
4730         for (timeout = 100; timeout; --timeout) {
4731                 msleep_interruptible(10);
4732                 if (loopback_test_rx(info)) {
4733                         rc = 0;
4734                         break;
4735                 }
4736         }
4737
4738         /* verify received frame length and contents */
4739         if (!rc && (info->tmp_rbuf_count != count ||
4740                   memcmp(buf, info->tmp_rbuf, count))) {
4741                 rc = -ENODEV;
4742         }
4743
4744         spin_lock_irqsave(&info->lock,flags);
4745         reset_adapter(info);
4746         spin_unlock_irqrestore(&info->lock,flags);
4747
4748         memcpy(&info->params, &params, sizeof(info->params));
4749         info->tty = oldtty;
4750
4751         info->init_error = rc ? DiagStatus_DmaFailure : 0;
4752         return rc;
4753 }
4754
4755 static int adapter_test(struct slgt_info *info)
4756 {
4757         DBGINFO(("testing %s\n", info->device_name));
4758         if (register_test(info) < 0) {
4759                 printk("register test failure %s addr=%08X\n",
4760                         info->device_name, info->phys_reg_addr);
4761         } else if (irq_test(info) < 0) {
4762                 printk("IRQ test failure %s IRQ=%d\n",
4763                         info->device_name, info->irq_level);
4764         } else if (loopback_test(info) < 0) {
4765                 printk("loopback test failure %s\n", info->device_name);
4766         }
4767         return info->init_error;
4768 }
4769
4770 /*
4771  * transmit timeout handler
4772  */
4773 static void tx_timeout(unsigned long context)
4774 {
4775         struct slgt_info *info = (struct slgt_info*)context;
4776         unsigned long flags;
4777
4778         DBGINFO(("%s tx_timeout\n", info->device_name));
4779         if(info->tx_active && info->params.mode == MGSL_MODE_HDLC) {
4780                 info->icount.txtimeout++;
4781         }
4782         spin_lock_irqsave(&info->lock,flags);
4783         info->tx_active = 0;
4784         info->tx_count = 0;
4785         spin_unlock_irqrestore(&info->lock,flags);
4786
4787 #if SYNCLINK_GENERIC_HDLC
4788         if (info->netcount)
4789                 hdlcdev_tx_done(info);
4790         else
4791 #endif
4792                 bh_transmit(info);
4793 }
4794
4795 /*
4796  * receive buffer polling timer
4797  */
4798 static void rx_timeout(unsigned long context)
4799 {
4800         struct slgt_info *info = (struct slgt_info*)context;
4801         unsigned long flags;
4802
4803         DBGINFO(("%s rx_timeout\n", info->device_name));
4804         spin_lock_irqsave(&info->lock, flags);
4805         info->pending_bh |= BH_RECEIVE;
4806         spin_unlock_irqrestore(&info->lock, flags);
4807         bh_handler(&info->task);
4808 }
4809