2 * file_storage.c -- File-backed USB Storage Gadget, for USB development
4 * Copyright (C) 2003-2005 Alan Stern
7 * Redistribution and use in source and binary forms, with or without
8 * modification, are permitted provided that the following conditions
10 * 1. Redistributions of source code must retain the above copyright
11 * notice, this list of conditions, and the following disclaimer,
12 * without modification.
13 * 2. Redistributions in binary form must reproduce the above copyright
14 * notice, this list of conditions and the following disclaimer in the
15 * documentation and/or other materials provided with the distribution.
16 * 3. The names of the above-listed copyright holders may not be used
17 * to endorse or promote products derived from this software without
18 * specific prior written permission.
20 * ALTERNATIVELY, this software may be distributed under the terms of the
21 * GNU General Public License ("GPL") as published by the Free Software
22 * Foundation, either version 2 of that License or (at your option) any
25 * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS
26 * IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO,
27 * THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR
28 * PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT OWNER OR
29 * CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL,
30 * EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO,
31 * PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR
32 * PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF
33 * LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING
34 * NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS
35 * SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
40 * The File-backed Storage Gadget acts as a USB Mass Storage device,
41 * appearing to the host as a disk drive. In addition to providing an
42 * example of a genuinely useful gadget driver for a USB device, it also
43 * illustrates a technique of double-buffering for increased throughput.
44 * Last but not least, it gives an easy way to probe the behavior of the
45 * Mass Storage drivers in a USB host.
47 * Backing storage is provided by a regular file or a block device, specified
48 * by the "file" module parameter. Access can be limited to read-only by
49 * setting the optional "ro" module parameter. The gadget will indicate that
50 * it has removable media if the optional "removable" module parameter is set.
52 * The gadget supports the Control-Bulk (CB), Control-Bulk-Interrupt (CBI),
53 * and Bulk-Only (also known as Bulk-Bulk-Bulk or BBB) transports, selected
54 * by the optional "transport" module parameter. It also supports the
55 * following protocols: RBC (0x01), ATAPI or SFF-8020i (0x02), QIC-157 (0c03),
56 * UFI (0x04), SFF-8070i (0x05), and transparent SCSI (0x06), selected by
57 * the optional "protocol" module parameter. In addition, the default
58 * Vendor ID, Product ID, and release number can be overridden.
60 * There is support for multiple logical units (LUNs), each of which has
61 * its own backing file. The number of LUNs can be set using the optional
62 * "luns" module parameter (anywhere from 1 to 8), and the corresponding
63 * files are specified using comma-separated lists for "file" and "ro".
64 * The default number of LUNs is taken from the number of "file" elements;
65 * it is 1 if "file" is not given. If "removable" is not set then a backing
66 * file must be specified for each LUN. If it is set, then an unspecified
67 * or empty backing filename means the LUN's medium is not loaded.
69 * Requirements are modest; only a bulk-in and a bulk-out endpoint are
70 * needed (an interrupt-out endpoint is also needed for CBI). The memory
71 * requirement amounts to two 16K buffers, size configurable by a parameter.
72 * Support is included for both full-speed and high-speed operation.
74 * Note that the driver is slightly non-portable in that it assumes a
75 * single memory/DMA buffer will be useable for bulk-in, bulk-out, and
76 * interrupt-in endpoints. With most device controllers this isn't an
77 * issue, but there may be some with hardware restrictions that prevent
78 * a buffer from being used by more than one endpoint.
82 * file=filename[,filename...]
83 * Required if "removable" is not set, names of
84 * the files or block devices used for
86 * ro=b[,b...] Default false, booleans for read-only access
87 * removable Default false, boolean for removable media
88 * luns=N Default N = number of filenames, number of
90 * stall Default determined according to the type of
91 * USB device controller (usually true),
92 * boolean to permit the driver to halt
94 * transport=XXX Default BBB, transport name (CB, CBI, or BBB)
95 * protocol=YYY Default SCSI, protocol name (RBC, 8020 or
96 * ATAPI, QIC, UFI, 8070, or SCSI;
98 * vendor=0xVVVV Default 0x0525 (NetChip), USB Vendor ID
99 * product=0xPPPP Default 0xa4a5 (FSG), USB Product ID
100 * release=0xRRRR Override the USB release number (bcdDevice)
101 * buflen=N Default N=16384, buffer size used (will be
102 * rounded down to a multiple of
105 * If CONFIG_USB_FILE_STORAGE_TEST is not set, only the "file", "ro",
106 * "removable", "luns", and "stall" options are available; default values
107 * are used for everything else.
109 * The pathnames of the backing files and the ro settings are available in
110 * the attribute files "file" and "ro" in the lun<n> subdirectory of the
111 * gadget's sysfs directory. If the "removable" option is set, writing to
112 * these files will simulate ejecting/loading the medium (writing an empty
113 * line means eject) and adjusting a write-enable tab. Changes to the ro
114 * setting are not allowed when the medium is loaded.
116 * This gadget driver is heavily based on "Gadget Zero" by David Brownell.
117 * The driver's SCSI command interface was based on the "Information
118 * technology - Small Computer System Interface - 2" document from
119 * X3T9.2 Project 375D, Revision 10L, 7-SEP-93, available at
120 * <http://www.t10.org/ftp/t10/drafts/s2/s2-r10l.pdf>. The single exception
121 * is opcode 0x23 (READ FORMAT CAPACITIES), which was based on the
122 * "Universal Serial Bus Mass Storage Class UFI Command Specification"
123 * document, Revision 1.0, December 14, 1998, available at
124 * <http://www.usb.org/developers/devclass_docs/usbmass-ufi10.pdf>.
131 * The FSG driver is fairly straightforward. There is a main kernel
132 * thread that handles most of the work. Interrupt routines field
133 * callbacks from the controller driver: bulk- and interrupt-request
134 * completion notifications, endpoint-0 events, and disconnect events.
135 * Completion events are passed to the main thread by wakeup calls. Many
136 * ep0 requests are handled at interrupt time, but SetInterface,
137 * SetConfiguration, and device reset requests are forwarded to the
138 * thread in the form of "exceptions" using SIGUSR1 signals (since they
139 * should interrupt any ongoing file I/O operations).
141 * The thread's main routine implements the standard command/data/status
142 * parts of a SCSI interaction. It and its subroutines are full of tests
143 * for pending signals/exceptions -- all this polling is necessary since
144 * the kernel has no setjmp/longjmp equivalents. (Maybe this is an
145 * indication that the driver really wants to be running in userspace.)
146 * An important point is that so long as the thread is alive it keeps an
147 * open reference to the backing file. This will prevent unmounting
148 * the backing file's underlying filesystem and could cause problems
149 * during system shutdown, for example. To prevent such problems, the
150 * thread catches INT, TERM, and KILL signals and converts them into
153 * In normal operation the main thread is started during the gadget's
154 * fsg_bind() callback and stopped during fsg_unbind(). But it can also
155 * exit when it receives a signal, and there's no point leaving the
156 * gadget running when the thread is dead. So just before the thread
157 * exits, it deregisters the gadget driver. This makes things a little
158 * tricky: The driver is deregistered at two places, and the exiting
159 * thread can indirectly call fsg_unbind() which in turn can tell the
160 * thread to exit. The first problem is resolved through the use of the
161 * REGISTERED atomic bitflag; the driver will only be deregistered once.
162 * The second problem is resolved by having fsg_unbind() check
163 * fsg->state; it won't try to stop the thread if the state is already
164 * FSG_STATE_TERMINATED.
166 * To provide maximum throughput, the driver uses a circular pipeline of
167 * buffer heads (struct fsg_buffhd). In principle the pipeline can be
168 * arbitrarily long; in practice the benefits don't justify having more
169 * than 2 stages (i.e., double buffering). But it helps to think of the
170 * pipeline as being a long one. Each buffer head contains a bulk-in and
171 * a bulk-out request pointer (since the buffer can be used for both
172 * output and input -- directions always are given from the host's
173 * point of view) as well as a pointer to the buffer and various state
176 * Use of the pipeline follows a simple protocol. There is a variable
177 * (fsg->next_buffhd_to_fill) that points to the next buffer head to use.
178 * At any time that buffer head may still be in use from an earlier
179 * request, so each buffer head has a state variable indicating whether
180 * it is EMPTY, FULL, or BUSY. Typical use involves waiting for the
181 * buffer head to be EMPTY, filling the buffer either by file I/O or by
182 * USB I/O (during which the buffer head is BUSY), and marking the buffer
183 * head FULL when the I/O is complete. Then the buffer will be emptied
184 * (again possibly by USB I/O, during which it is marked BUSY) and
185 * finally marked EMPTY again (possibly by a completion routine).
187 * A module parameter tells the driver to avoid stalling the bulk
188 * endpoints wherever the transport specification allows. This is
189 * necessary for some UDCs like the SuperH, which cannot reliably clear a
190 * halt on a bulk endpoint. However, under certain circumstances the
191 * Bulk-only specification requires a stall. In such cases the driver
192 * will halt the endpoint and set a flag indicating that it should clear
193 * the halt in software during the next device reset. Hopefully this
194 * will permit everything to work correctly. Furthermore, although the
195 * specification allows the bulk-out endpoint to halt when the host sends
196 * too much data, implementing this would cause an unavoidable race.
197 * The driver will always use the "no-stall" approach for OUT transfers.
199 * One subtle point concerns sending status-stage responses for ep0
200 * requests. Some of these requests, such as device reset, can involve
201 * interrupting an ongoing file I/O operation, which might take an
202 * arbitrarily long time. During that delay the host might give up on
203 * the original ep0 request and issue a new one. When that happens the
204 * driver should not notify the host about completion of the original
205 * request, as the host will no longer be waiting for it. So the driver
206 * assigns to each ep0 request a unique tag, and it keeps track of the
207 * tag value of the request associated with a long-running exception
208 * (device-reset, interface-change, or configuration-change). When the
209 * exception handler is finished, the status-stage response is submitted
210 * only if the current ep0 request tag is equal to the exception request
211 * tag. Thus only the most recently received ep0 request will get a
212 * status-stage response.
214 * Warning: This driver source file is too long. It ought to be split up
215 * into a header file plus about 3 separate .c files, to handle the details
216 * of the Gadget, USB Mass Storage, and SCSI protocols.
225 #include <asm/system.h>
226 #include <asm/uaccess.h>
228 #include <linux/bitops.h>
229 #include <linux/blkdev.h>
230 #include <linux/compiler.h>
231 #include <linux/completion.h>
232 #include <linux/dcache.h>
233 #include <linux/delay.h>
234 #include <linux/device.h>
235 #include <linux/fcntl.h>
236 #include <linux/file.h>
237 #include <linux/fs.h>
238 #include <linux/init.h>
239 #include <linux/kernel.h>
240 #include <linux/kref.h>
241 #include <linux/kthread.h>
242 #include <linux/limits.h>
243 #include <linux/list.h>
244 #include <linux/module.h>
245 #include <linux/moduleparam.h>
246 #include <linux/pagemap.h>
247 #include <linux/rwsem.h>
248 #include <linux/sched.h>
249 #include <linux/signal.h>
250 #include <linux/slab.h>
251 #include <linux/spinlock.h>
252 #include <linux/string.h>
253 #include <linux/suspend.h>
254 #include <linux/utsname.h>
256 #include <linux/usb_ch9.h>
257 #include <linux/usb_gadget.h>
259 #include "gadget_chips.h"
262 /*-------------------------------------------------------------------------*/
264 #define DRIVER_DESC "File-backed Storage Gadget"
265 #define DRIVER_NAME "g_file_storage"
266 #define DRIVER_VERSION "28 November 2005"
268 static const char longname[] = DRIVER_DESC;
269 static const char shortname[] = DRIVER_NAME;
271 MODULE_DESCRIPTION(DRIVER_DESC);
272 MODULE_AUTHOR("Alan Stern");
273 MODULE_LICENSE("Dual BSD/GPL");
275 /* Thanks to NetChip Technologies for donating this product ID.
277 * DO NOT REUSE THESE IDs with any other driver!! Ever!!
278 * Instead: allocate your own, using normal USB-IF procedures. */
279 #define DRIVER_VENDOR_ID 0x0525 // NetChip
280 #define DRIVER_PRODUCT_ID 0xa4a5 // Linux-USB File-backed Storage Gadget
284 * This driver assumes self-powered hardware and has no way for users to
285 * trigger remote wakeup. It uses autoconfiguration to select endpoints
286 * and endpoint addresses.
290 /*-------------------------------------------------------------------------*/
292 #define xprintk(f,level,fmt,args...) \
293 dev_printk(level , &(f)->gadget->dev , fmt , ## args)
294 #define yprintk(l,level,fmt,args...) \
295 dev_printk(level , &(l)->dev , fmt , ## args)
298 #define DBG(fsg,fmt,args...) \
299 xprintk(fsg , KERN_DEBUG , fmt , ## args)
300 #define LDBG(lun,fmt,args...) \
301 yprintk(lun , KERN_DEBUG , fmt , ## args)
302 #define MDBG(fmt,args...) \
303 printk(KERN_DEBUG DRIVER_NAME ": " fmt , ## args)
305 #define DBG(fsg,fmt,args...) \
307 #define LDBG(lun,fmt,args...) \
309 #define MDBG(fmt,args...) \
319 #define VDBG(fsg,fmt,args...) \
321 #define VLDBG(lun,fmt,args...) \
325 #define ERROR(fsg,fmt,args...) \
326 xprintk(fsg , KERN_ERR , fmt , ## args)
327 #define LERROR(lun,fmt,args...) \
328 yprintk(lun , KERN_ERR , fmt , ## args)
330 #define WARN(fsg,fmt,args...) \
331 xprintk(fsg , KERN_WARNING , fmt , ## args)
332 #define LWARN(lun,fmt,args...) \
333 yprintk(lun , KERN_WARNING , fmt , ## args)
335 #define INFO(fsg,fmt,args...) \
336 xprintk(fsg , KERN_INFO , fmt , ## args)
337 #define LINFO(lun,fmt,args...) \
338 yprintk(lun , KERN_INFO , fmt , ## args)
340 #define MINFO(fmt,args...) \
341 printk(KERN_INFO DRIVER_NAME ": " fmt , ## args)
344 /*-------------------------------------------------------------------------*/
346 /* Encapsulate the module parameter settings */
351 char *file[MAX_LUNS];
360 char *transport_parm;
362 unsigned short vendor;
363 unsigned short product;
364 unsigned short release;
368 char *transport_name;
372 } mod_data = { // Default values
373 .transport_parm = "BBB",
374 .protocol_parm = "SCSI",
377 .vendor = DRIVER_VENDOR_ID,
378 .product = DRIVER_PRODUCT_ID,
379 .release = 0xffff, // Use controller chip type
384 module_param_array_named(file, mod_data.file, charp, &mod_data.num_filenames,
386 MODULE_PARM_DESC(file, "names of backing files or devices");
388 module_param_array_named(ro, mod_data.ro, bool, &mod_data.num_ros, S_IRUGO);
389 MODULE_PARM_DESC(ro, "true to force read-only");
391 module_param_named(luns, mod_data.nluns, uint, S_IRUGO);
392 MODULE_PARM_DESC(luns, "number of LUNs");
394 module_param_named(removable, mod_data.removable, bool, S_IRUGO);
395 MODULE_PARM_DESC(removable, "true to simulate removable media");
397 module_param_named(stall, mod_data.can_stall, bool, S_IRUGO);
398 MODULE_PARM_DESC(stall, "false to prevent bulk stalls");
401 /* In the non-TEST version, only the module parameters listed above
403 #ifdef CONFIG_USB_FILE_STORAGE_TEST
405 module_param_named(transport, mod_data.transport_parm, charp, S_IRUGO);
406 MODULE_PARM_DESC(transport, "type of transport (BBB, CBI, or CB)");
408 module_param_named(protocol, mod_data.protocol_parm, charp, S_IRUGO);
409 MODULE_PARM_DESC(protocol, "type of protocol (RBC, 8020, QIC, UFI, "
412 module_param_named(vendor, mod_data.vendor, ushort, S_IRUGO);
413 MODULE_PARM_DESC(vendor, "USB Vendor ID");
415 module_param_named(product, mod_data.product, ushort, S_IRUGO);
416 MODULE_PARM_DESC(product, "USB Product ID");
418 module_param_named(release, mod_data.release, ushort, S_IRUGO);
419 MODULE_PARM_DESC(release, "USB release number");
421 module_param_named(buflen, mod_data.buflen, uint, S_IRUGO);
422 MODULE_PARM_DESC(buflen, "I/O buffer size");
424 #endif /* CONFIG_USB_FILE_STORAGE_TEST */
427 /*-------------------------------------------------------------------------*/
429 /* USB protocol value = the transport method */
430 #define USB_PR_CBI 0x00 // Control/Bulk/Interrupt
431 #define USB_PR_CB 0x01 // Control/Bulk w/o interrupt
432 #define USB_PR_BULK 0x50 // Bulk-only
434 /* USB subclass value = the protocol encapsulation */
435 #define USB_SC_RBC 0x01 // Reduced Block Commands (flash)
436 #define USB_SC_8020 0x02 // SFF-8020i, MMC-2, ATAPI (CD-ROM)
437 #define USB_SC_QIC 0x03 // QIC-157 (tape)
438 #define USB_SC_UFI 0x04 // UFI (floppy)
439 #define USB_SC_8070 0x05 // SFF-8070i (removable)
440 #define USB_SC_SCSI 0x06 // Transparent SCSI
442 /* Bulk-only data structures */
444 /* Command Block Wrapper */
445 struct bulk_cb_wrap {
446 __le32 Signature; // Contains 'USBC'
447 u32 Tag; // Unique per command id
448 __le32 DataTransferLength; // Size of the data
449 u8 Flags; // Direction in bit 7
450 u8 Lun; // LUN (normally 0)
451 u8 Length; // Of the CDB, <= MAX_COMMAND_SIZE
452 u8 CDB[16]; // Command Data Block
455 #define USB_BULK_CB_WRAP_LEN 31
456 #define USB_BULK_CB_SIG 0x43425355 // Spells out USBC
457 #define USB_BULK_IN_FLAG 0x80
459 /* Command Status Wrapper */
460 struct bulk_cs_wrap {
461 __le32 Signature; // Should = 'USBS'
462 u32 Tag; // Same as original command
463 __le32 Residue; // Amount not transferred
464 u8 Status; // See below
467 #define USB_BULK_CS_WRAP_LEN 13
468 #define USB_BULK_CS_SIG 0x53425355 // Spells out 'USBS'
469 #define USB_STATUS_PASS 0
470 #define USB_STATUS_FAIL 1
471 #define USB_STATUS_PHASE_ERROR 2
473 /* Bulk-only class specific requests */
474 #define USB_BULK_RESET_REQUEST 0xff
475 #define USB_BULK_GET_MAX_LUN_REQUEST 0xfe
478 /* CBI Interrupt data structure */
479 struct interrupt_data {
484 #define CBI_INTERRUPT_DATA_LEN 2
486 /* CBI Accept Device-Specific Command request */
487 #define USB_CBI_ADSC_REQUEST 0x00
490 #define MAX_COMMAND_SIZE 16 // Length of a SCSI Command Data Block
492 /* SCSI commands that we recognize */
493 #define SC_FORMAT_UNIT 0x04
494 #define SC_INQUIRY 0x12
495 #define SC_MODE_SELECT_6 0x15
496 #define SC_MODE_SELECT_10 0x55
497 #define SC_MODE_SENSE_6 0x1a
498 #define SC_MODE_SENSE_10 0x5a
499 #define SC_PREVENT_ALLOW_MEDIUM_REMOVAL 0x1e
500 #define SC_READ_6 0x08
501 #define SC_READ_10 0x28
502 #define SC_READ_12 0xa8
503 #define SC_READ_CAPACITY 0x25
504 #define SC_READ_FORMAT_CAPACITIES 0x23
505 #define SC_RELEASE 0x17
506 #define SC_REQUEST_SENSE 0x03
507 #define SC_RESERVE 0x16
508 #define SC_SEND_DIAGNOSTIC 0x1d
509 #define SC_START_STOP_UNIT 0x1b
510 #define SC_SYNCHRONIZE_CACHE 0x35
511 #define SC_TEST_UNIT_READY 0x00
512 #define SC_VERIFY 0x2f
513 #define SC_WRITE_6 0x0a
514 #define SC_WRITE_10 0x2a
515 #define SC_WRITE_12 0xaa
517 /* SCSI Sense Key/Additional Sense Code/ASC Qualifier values */
518 #define SS_NO_SENSE 0
519 #define SS_COMMUNICATION_FAILURE 0x040800
520 #define SS_INVALID_COMMAND 0x052000
521 #define SS_INVALID_FIELD_IN_CDB 0x052400
522 #define SS_LOGICAL_BLOCK_ADDRESS_OUT_OF_RANGE 0x052100
523 #define SS_LOGICAL_UNIT_NOT_SUPPORTED 0x052500
524 #define SS_MEDIUM_NOT_PRESENT 0x023a00
525 #define SS_MEDIUM_REMOVAL_PREVENTED 0x055302
526 #define SS_NOT_READY_TO_READY_TRANSITION 0x062800
527 #define SS_RESET_OCCURRED 0x062900
528 #define SS_SAVING_PARAMETERS_NOT_SUPPORTED 0x053900
529 #define SS_UNRECOVERED_READ_ERROR 0x031100
530 #define SS_WRITE_ERROR 0x030c02
531 #define SS_WRITE_PROTECTED 0x072700
533 #define SK(x) ((u8) ((x) >> 16)) // Sense Key byte, etc.
534 #define ASC(x) ((u8) ((x) >> 8))
535 #define ASCQ(x) ((u8) (x))
538 /*-------------------------------------------------------------------------*/
541 * These definitions will permit the compiler to avoid generating code for
542 * parts of the driver that aren't used in the non-TEST version. Even gcc
543 * can recognize when a test of a constant expression yields a dead code
547 #ifdef CONFIG_USB_FILE_STORAGE_TEST
549 #define transport_is_bbb() (mod_data.transport_type == USB_PR_BULK)
550 #define transport_is_cbi() (mod_data.transport_type == USB_PR_CBI)
551 #define protocol_is_scsi() (mod_data.protocol_type == USB_SC_SCSI)
555 #define transport_is_bbb() 1
556 #define transport_is_cbi() 0
557 #define protocol_is_scsi() 1
559 #endif /* CONFIG_USB_FILE_STORAGE_TEST */
568 unsigned int prevent_medium_removal : 1;
569 unsigned int registered : 1;
570 unsigned int info_valid : 1;
574 u32 unit_attention_data;
579 #define backing_file_is_open(curlun) ((curlun)->filp != NULL)
581 static inline struct lun *dev_to_lun(struct device *dev)
583 return container_of(dev, struct lun, dev);
587 /* Big enough to hold our biggest descriptor */
588 #define EP0_BUFSIZE 256
589 #define DELAYED_STATUS (EP0_BUFSIZE + 999) // An impossibly large value
591 /* Number of buffers we will use. 2 is enough for double-buffering */
592 #define NUM_BUFFERS 2
594 enum fsg_buffer_state {
603 enum fsg_buffer_state state;
604 struct fsg_buffhd *next;
606 /* The NetChip 2280 is faster, and handles some protocol faults
607 * better, if we don't submit any short bulk-out read requests.
608 * So we will record the intended request length here. */
609 unsigned int bulk_out_intended_length;
611 struct usb_request *inreq;
613 struct usb_request *outreq;
618 FSG_STATE_COMMAND_PHASE = -10, // This one isn't used anywhere
619 FSG_STATE_DATA_PHASE,
620 FSG_STATE_STATUS_PHASE,
623 FSG_STATE_ABORT_BULK_OUT,
625 FSG_STATE_INTERFACE_CHANGE,
626 FSG_STATE_CONFIG_CHANGE,
627 FSG_STATE_DISCONNECT,
632 enum data_direction {
633 DATA_DIR_UNKNOWN = 0,
640 /* lock protects: state, all the req_busy's, and cbbuf_cmnd */
642 struct usb_gadget *gadget;
644 /* filesem protects: backing files in use */
645 struct rw_semaphore filesem;
647 /* reference counting: wait until all LUNs are released */
650 struct usb_ep *ep0; // Handy copy of gadget->ep0
651 struct usb_request *ep0req; // For control responses
652 unsigned int ep0_req_tag;
653 const char *ep0req_name;
655 struct usb_request *intreq; // For interrupt responses
657 struct fsg_buffhd *intr_buffhd;
659 unsigned int bulk_out_maxpacket;
660 enum fsg_state state; // For exception handling
661 unsigned int exception_req_tag;
663 u8 config, new_config;
665 unsigned int running : 1;
666 unsigned int bulk_in_enabled : 1;
667 unsigned int bulk_out_enabled : 1;
668 unsigned int intr_in_enabled : 1;
669 unsigned int phase_error : 1;
670 unsigned int short_packet_received : 1;
671 unsigned int bad_lun_okay : 1;
673 unsigned long atomic_bitflags;
675 #define CLEAR_BULK_HALTS 1
678 struct usb_ep *bulk_in;
679 struct usb_ep *bulk_out;
680 struct usb_ep *intr_in;
682 struct fsg_buffhd *next_buffhd_to_fill;
683 struct fsg_buffhd *next_buffhd_to_drain;
684 struct fsg_buffhd buffhds[NUM_BUFFERS];
686 int thread_wakeup_needed;
687 struct completion thread_notifier;
688 struct task_struct *thread_task;
689 sigset_t thread_signal_mask;
692 u8 cmnd[MAX_COMMAND_SIZE];
693 enum data_direction data_dir;
695 u32 data_size_from_cmnd;
701 /* The CB protocol offers no way for a host to know when a command
702 * has completed. As a result the next command may arrive early,
703 * and we will still have to handle it. For that reason we need
704 * a buffer to store new commands when using CB (or CBI, which
705 * does not oblige a host to wait for command completion either). */
707 u8 cbbuf_cmnd[MAX_COMMAND_SIZE];
714 typedef void (*fsg_routine_t)(struct fsg_dev *);
716 static int inline exception_in_progress(struct fsg_dev *fsg)
718 return (fsg->state > FSG_STATE_IDLE);
721 /* Make bulk-out requests be divisible by the maxpacket size */
722 static void inline set_bulk_out_req_length(struct fsg_dev *fsg,
723 struct fsg_buffhd *bh, unsigned int length)
727 bh->bulk_out_intended_length = length;
728 rem = length % fsg->bulk_out_maxpacket;
730 length += fsg->bulk_out_maxpacket - rem;
731 bh->outreq->length = length;
734 static struct fsg_dev *the_fsg;
735 static struct usb_gadget_driver fsg_driver;
737 static void close_backing_file(struct lun *curlun);
738 static void close_all_backing_files(struct fsg_dev *fsg);
741 /*-------------------------------------------------------------------------*/
745 static void dump_msg(struct fsg_dev *fsg, const char *label,
746 const u8 *buf, unsigned int length)
748 unsigned int start, num, i;
753 DBG(fsg, "%s, length %u:\n", label, length);
757 num = min(length, 16u);
759 for (i = 0; i < num; ++i) {
762 sprintf(p, " %02x", buf[i]);
766 printk(KERN_DEBUG "%6x: %s\n", start, line);
773 static void inline dump_cdb(struct fsg_dev *fsg)
778 static void inline dump_msg(struct fsg_dev *fsg, const char *label,
779 const u8 *buf, unsigned int length)
782 static void inline dump_cdb(struct fsg_dev *fsg)
785 char cmdbuf[3*MAX_COMMAND_SIZE + 1];
787 for (i = 0; i < fsg->cmnd_size; ++i)
788 sprintf(cmdbuf + i*3, " %02x", fsg->cmnd[i]);
789 VDBG(fsg, "SCSI CDB: %s\n", cmdbuf);
792 #endif /* DUMP_MSGS */
795 static int fsg_set_halt(struct fsg_dev *fsg, struct usb_ep *ep)
799 if (ep == fsg->bulk_in)
801 else if (ep == fsg->bulk_out)
805 DBG(fsg, "%s set halt\n", name);
806 return usb_ep_set_halt(ep);
810 /*-------------------------------------------------------------------------*/
812 /* Routines for unaligned data access */
814 static u16 inline get_be16(u8 *buf)
816 return ((u16) buf[0] << 8) | ((u16) buf[1]);
819 static u32 inline get_be32(u8 *buf)
821 return ((u32) buf[0] << 24) | ((u32) buf[1] << 16) |
822 ((u32) buf[2] << 8) | ((u32) buf[3]);
825 static void inline put_be16(u8 *buf, u16 val)
831 static void inline put_be32(u8 *buf, u32 val)
840 /*-------------------------------------------------------------------------*/
843 * DESCRIPTORS ... most are static, but strings and (full) configuration
844 * descriptors are built on demand. Also the (static) config and interface
845 * descriptors are adjusted during fsg_bind().
847 #define STRING_MANUFACTURER 1
848 #define STRING_PRODUCT 2
849 #define STRING_SERIAL 3
850 #define STRING_CONFIG 4
851 #define STRING_INTERFACE 5
853 /* There is only one configuration. */
854 #define CONFIG_VALUE 1
856 static struct usb_device_descriptor
858 .bLength = sizeof device_desc,
859 .bDescriptorType = USB_DT_DEVICE,
861 .bcdUSB = __constant_cpu_to_le16(0x0200),
862 .bDeviceClass = USB_CLASS_PER_INTERFACE,
864 /* The next three values can be overridden by module parameters */
865 .idVendor = __constant_cpu_to_le16(DRIVER_VENDOR_ID),
866 .idProduct = __constant_cpu_to_le16(DRIVER_PRODUCT_ID),
867 .bcdDevice = __constant_cpu_to_le16(0xffff),
869 .iManufacturer = STRING_MANUFACTURER,
870 .iProduct = STRING_PRODUCT,
871 .iSerialNumber = STRING_SERIAL,
872 .bNumConfigurations = 1,
875 static struct usb_config_descriptor
877 .bLength = sizeof config_desc,
878 .bDescriptorType = USB_DT_CONFIG,
880 /* wTotalLength computed by usb_gadget_config_buf() */
882 .bConfigurationValue = CONFIG_VALUE,
883 .iConfiguration = STRING_CONFIG,
884 .bmAttributes = USB_CONFIG_ATT_ONE | USB_CONFIG_ATT_SELFPOWER,
885 .bMaxPower = 1, // self-powered
888 static struct usb_otg_descriptor
890 .bLength = sizeof(otg_desc),
891 .bDescriptorType = USB_DT_OTG,
893 .bmAttributes = USB_OTG_SRP,
896 /* There is only one interface. */
898 static struct usb_interface_descriptor
900 .bLength = sizeof intf_desc,
901 .bDescriptorType = USB_DT_INTERFACE,
903 .bNumEndpoints = 2, // Adjusted during fsg_bind()
904 .bInterfaceClass = USB_CLASS_MASS_STORAGE,
905 .bInterfaceSubClass = USB_SC_SCSI, // Adjusted during fsg_bind()
906 .bInterfaceProtocol = USB_PR_BULK, // Adjusted during fsg_bind()
907 .iInterface = STRING_INTERFACE,
910 /* Three full-speed endpoint descriptors: bulk-in, bulk-out,
911 * and interrupt-in. */
913 static struct usb_endpoint_descriptor
915 .bLength = USB_DT_ENDPOINT_SIZE,
916 .bDescriptorType = USB_DT_ENDPOINT,
918 .bEndpointAddress = USB_DIR_IN,
919 .bmAttributes = USB_ENDPOINT_XFER_BULK,
920 /* wMaxPacketSize set by autoconfiguration */
923 static struct usb_endpoint_descriptor
925 .bLength = USB_DT_ENDPOINT_SIZE,
926 .bDescriptorType = USB_DT_ENDPOINT,
928 .bEndpointAddress = USB_DIR_OUT,
929 .bmAttributes = USB_ENDPOINT_XFER_BULK,
930 /* wMaxPacketSize set by autoconfiguration */
933 static struct usb_endpoint_descriptor
935 .bLength = USB_DT_ENDPOINT_SIZE,
936 .bDescriptorType = USB_DT_ENDPOINT,
938 .bEndpointAddress = USB_DIR_IN,
939 .bmAttributes = USB_ENDPOINT_XFER_INT,
940 .wMaxPacketSize = __constant_cpu_to_le16(2),
941 .bInterval = 32, // frames -> 32 ms
944 static const struct usb_descriptor_header *fs_function[] = {
945 (struct usb_descriptor_header *) &otg_desc,
946 (struct usb_descriptor_header *) &intf_desc,
947 (struct usb_descriptor_header *) &fs_bulk_in_desc,
948 (struct usb_descriptor_header *) &fs_bulk_out_desc,
949 (struct usb_descriptor_header *) &fs_intr_in_desc,
952 #define FS_FUNCTION_PRE_EP_ENTRIES 2
955 #ifdef CONFIG_USB_GADGET_DUALSPEED
958 * USB 2.0 devices need to expose both high speed and full speed
959 * descriptors, unless they only run at full speed.
961 * That means alternate endpoint descriptors (bigger packets)
962 * and a "device qualifier" ... plus more construction options
963 * for the config descriptor.
965 static struct usb_qualifier_descriptor
967 .bLength = sizeof dev_qualifier,
968 .bDescriptorType = USB_DT_DEVICE_QUALIFIER,
970 .bcdUSB = __constant_cpu_to_le16(0x0200),
971 .bDeviceClass = USB_CLASS_PER_INTERFACE,
973 .bNumConfigurations = 1,
976 static struct usb_endpoint_descriptor
978 .bLength = USB_DT_ENDPOINT_SIZE,
979 .bDescriptorType = USB_DT_ENDPOINT,
981 /* bEndpointAddress copied from fs_bulk_in_desc during fsg_bind() */
982 .bmAttributes = USB_ENDPOINT_XFER_BULK,
983 .wMaxPacketSize = __constant_cpu_to_le16(512),
986 static struct usb_endpoint_descriptor
988 .bLength = USB_DT_ENDPOINT_SIZE,
989 .bDescriptorType = USB_DT_ENDPOINT,
991 /* bEndpointAddress copied from fs_bulk_out_desc during fsg_bind() */
992 .bmAttributes = USB_ENDPOINT_XFER_BULK,
993 .wMaxPacketSize = __constant_cpu_to_le16(512),
994 .bInterval = 1, // NAK every 1 uframe
997 static struct usb_endpoint_descriptor
999 .bLength = USB_DT_ENDPOINT_SIZE,
1000 .bDescriptorType = USB_DT_ENDPOINT,
1002 /* bEndpointAddress copied from fs_intr_in_desc during fsg_bind() */
1003 .bmAttributes = USB_ENDPOINT_XFER_INT,
1004 .wMaxPacketSize = __constant_cpu_to_le16(2),
1005 .bInterval = 9, // 2**(9-1) = 256 uframes -> 32 ms
1008 static const struct usb_descriptor_header *hs_function[] = {
1009 (struct usb_descriptor_header *) &otg_desc,
1010 (struct usb_descriptor_header *) &intf_desc,
1011 (struct usb_descriptor_header *) &hs_bulk_in_desc,
1012 (struct usb_descriptor_header *) &hs_bulk_out_desc,
1013 (struct usb_descriptor_header *) &hs_intr_in_desc,
1016 #define HS_FUNCTION_PRE_EP_ENTRIES 2
1018 /* Maxpacket and other transfer characteristics vary by speed. */
1019 #define ep_desc(g,fs,hs) (((g)->speed==USB_SPEED_HIGH) ? (hs) : (fs))
1023 /* If there's no high speed support, always use the full-speed descriptor. */
1024 #define ep_desc(g,fs,hs) fs
1026 #endif /* !CONFIG_USB_GADGET_DUALSPEED */
1029 /* The CBI specification limits the serial string to 12 uppercase hexadecimal
1031 static char manufacturer[64];
1032 static char serial[13];
1034 /* Static strings, in UTF-8 (for simplicity we use only ASCII characters) */
1035 static struct usb_string strings[] = {
1036 {STRING_MANUFACTURER, manufacturer},
1037 {STRING_PRODUCT, longname},
1038 {STRING_SERIAL, serial},
1039 {STRING_CONFIG, "Self-powered"},
1040 {STRING_INTERFACE, "Mass Storage"},
1044 static struct usb_gadget_strings stringtab = {
1045 .language = 0x0409, // en-us
1051 * Config descriptors must agree with the code that sets configurations
1052 * and with code managing interfaces and their altsettings. They must
1053 * also handle different speeds and other-speed requests.
1055 static int populate_config_buf(struct usb_gadget *gadget,
1056 u8 *buf, u8 type, unsigned index)
1058 #ifdef CONFIG_USB_GADGET_DUALSPEED
1059 enum usb_device_speed speed = gadget->speed;
1062 const struct usb_descriptor_header **function;
1067 #ifdef CONFIG_USB_GADGET_DUALSPEED
1068 if (type == USB_DT_OTHER_SPEED_CONFIG)
1069 speed = (USB_SPEED_FULL + USB_SPEED_HIGH) - speed;
1070 if (speed == USB_SPEED_HIGH)
1071 function = hs_function;
1074 function = fs_function;
1076 /* for now, don't advertise srp-only devices */
1077 if (!gadget->is_otg)
1080 len = usb_gadget_config_buf(&config_desc, buf, EP0_BUFSIZE, function);
1081 ((struct usb_config_descriptor *) buf)->bDescriptorType = type;
1086 /*-------------------------------------------------------------------------*/
1088 /* These routines may be called in process context or in_irq */
1090 /* Caller must hold fsg->lock */
1091 static void wakeup_thread(struct fsg_dev *fsg)
1093 /* Tell the main thread that something has happened */
1094 fsg->thread_wakeup_needed = 1;
1095 if (fsg->thread_task)
1096 wake_up_process(fsg->thread_task);
1100 static void raise_exception(struct fsg_dev *fsg, enum fsg_state new_state)
1102 unsigned long flags;
1104 /* Do nothing if a higher-priority exception is already in progress.
1105 * If a lower-or-equal priority exception is in progress, preempt it
1106 * and notify the main thread by sending it a signal. */
1107 spin_lock_irqsave(&fsg->lock, flags);
1108 if (fsg->state <= new_state) {
1109 fsg->exception_req_tag = fsg->ep0_req_tag;
1110 fsg->state = new_state;
1111 if (fsg->thread_task)
1112 send_sig_info(SIGUSR1, SEND_SIG_FORCED,
1115 spin_unlock_irqrestore(&fsg->lock, flags);
1119 /*-------------------------------------------------------------------------*/
1121 /* The disconnect callback and ep0 routines. These always run in_irq,
1122 * except that ep0_queue() is called in the main thread to acknowledge
1123 * completion of various requests: set config, set interface, and
1124 * Bulk-only device reset. */
1126 static void fsg_disconnect(struct usb_gadget *gadget)
1128 struct fsg_dev *fsg = get_gadget_data(gadget);
1130 DBG(fsg, "disconnect or port reset\n");
1131 raise_exception(fsg, FSG_STATE_DISCONNECT);
1135 static int ep0_queue(struct fsg_dev *fsg)
1139 rc = usb_ep_queue(fsg->ep0, fsg->ep0req, GFP_ATOMIC);
1140 if (rc != 0 && rc != -ESHUTDOWN) {
1142 /* We can't do much more than wait for a reset */
1143 WARN(fsg, "error in submission: %s --> %d\n",
1144 fsg->ep0->name, rc);
1149 static void ep0_complete(struct usb_ep *ep, struct usb_request *req)
1151 struct fsg_dev *fsg = (struct fsg_dev *) ep->driver_data;
1153 if (req->actual > 0)
1154 dump_msg(fsg, fsg->ep0req_name, req->buf, req->actual);
1155 if (req->status || req->actual != req->length)
1156 DBG(fsg, "%s --> %d, %u/%u\n", __FUNCTION__,
1157 req->status, req->actual, req->length);
1158 if (req->status == -ECONNRESET) // Request was cancelled
1159 usb_ep_fifo_flush(ep);
1161 if (req->status == 0 && req->context)
1162 ((fsg_routine_t) (req->context))(fsg);
1166 /*-------------------------------------------------------------------------*/
1168 /* Bulk and interrupt endpoint completion handlers.
1169 * These always run in_irq. */
1171 static void bulk_in_complete(struct usb_ep *ep, struct usb_request *req)
1173 struct fsg_dev *fsg = (struct fsg_dev *) ep->driver_data;
1174 struct fsg_buffhd *bh = (struct fsg_buffhd *) req->context;
1176 if (req->status || req->actual != req->length)
1177 DBG(fsg, "%s --> %d, %u/%u\n", __FUNCTION__,
1178 req->status, req->actual, req->length);
1179 if (req->status == -ECONNRESET) // Request was cancelled
1180 usb_ep_fifo_flush(ep);
1182 /* Hold the lock while we update the request and buffer states */
1184 spin_lock(&fsg->lock);
1186 bh->state = BUF_STATE_EMPTY;
1188 spin_unlock(&fsg->lock);
1191 static void bulk_out_complete(struct usb_ep *ep, struct usb_request *req)
1193 struct fsg_dev *fsg = (struct fsg_dev *) ep->driver_data;
1194 struct fsg_buffhd *bh = (struct fsg_buffhd *) req->context;
1196 dump_msg(fsg, "bulk-out", req->buf, req->actual);
1197 if (req->status || req->actual != bh->bulk_out_intended_length)
1198 DBG(fsg, "%s --> %d, %u/%u\n", __FUNCTION__,
1199 req->status, req->actual,
1200 bh->bulk_out_intended_length);
1201 if (req->status == -ECONNRESET) // Request was cancelled
1202 usb_ep_fifo_flush(ep);
1204 /* Hold the lock while we update the request and buffer states */
1206 spin_lock(&fsg->lock);
1207 bh->outreq_busy = 0;
1208 bh->state = BUF_STATE_FULL;
1210 spin_unlock(&fsg->lock);
1214 #ifdef CONFIG_USB_FILE_STORAGE_TEST
1215 static void intr_in_complete(struct usb_ep *ep, struct usb_request *req)
1217 struct fsg_dev *fsg = (struct fsg_dev *) ep->driver_data;
1218 struct fsg_buffhd *bh = (struct fsg_buffhd *) req->context;
1220 if (req->status || req->actual != req->length)
1221 DBG(fsg, "%s --> %d, %u/%u\n", __FUNCTION__,
1222 req->status, req->actual, req->length);
1223 if (req->status == -ECONNRESET) // Request was cancelled
1224 usb_ep_fifo_flush(ep);
1226 /* Hold the lock while we update the request and buffer states */
1228 spin_lock(&fsg->lock);
1229 fsg->intreq_busy = 0;
1230 bh->state = BUF_STATE_EMPTY;
1232 spin_unlock(&fsg->lock);
1236 static void intr_in_complete(struct usb_ep *ep, struct usb_request *req)
1238 #endif /* CONFIG_USB_FILE_STORAGE_TEST */
1241 /*-------------------------------------------------------------------------*/
1243 /* Ep0 class-specific handlers. These always run in_irq. */
1245 #ifdef CONFIG_USB_FILE_STORAGE_TEST
1246 static void received_cbi_adsc(struct fsg_dev *fsg, struct fsg_buffhd *bh)
1248 struct usb_request *req = fsg->ep0req;
1249 static u8 cbi_reset_cmnd[6] = {
1250 SC_SEND_DIAGNOSTIC, 4, 0xff, 0xff, 0xff, 0xff};
1252 /* Error in command transfer? */
1253 if (req->status || req->length != req->actual ||
1254 req->actual < 6 || req->actual > MAX_COMMAND_SIZE) {
1256 /* Not all controllers allow a protocol stall after
1257 * receiving control-out data, but we'll try anyway. */
1258 fsg_set_halt(fsg, fsg->ep0);
1259 return; // Wait for reset
1262 /* Is it the special reset command? */
1263 if (req->actual >= sizeof cbi_reset_cmnd &&
1264 memcmp(req->buf, cbi_reset_cmnd,
1265 sizeof cbi_reset_cmnd) == 0) {
1267 /* Raise an exception to stop the current operation
1268 * and reinitialize our state. */
1269 DBG(fsg, "cbi reset request\n");
1270 raise_exception(fsg, FSG_STATE_RESET);
1274 VDBG(fsg, "CB[I] accept device-specific command\n");
1275 spin_lock(&fsg->lock);
1277 /* Save the command for later */
1278 if (fsg->cbbuf_cmnd_size)
1279 WARN(fsg, "CB[I] overwriting previous command\n");
1280 fsg->cbbuf_cmnd_size = req->actual;
1281 memcpy(fsg->cbbuf_cmnd, req->buf, fsg->cbbuf_cmnd_size);
1284 spin_unlock(&fsg->lock);
1288 static void received_cbi_adsc(struct fsg_dev *fsg, struct fsg_buffhd *bh)
1290 #endif /* CONFIG_USB_FILE_STORAGE_TEST */
1293 static int class_setup_req(struct fsg_dev *fsg,
1294 const struct usb_ctrlrequest *ctrl)
1296 struct usb_request *req = fsg->ep0req;
1297 int value = -EOPNOTSUPP;
1298 u16 w_index = le16_to_cpu(ctrl->wIndex);
1299 u16 w_length = le16_to_cpu(ctrl->wLength);
1304 /* Handle Bulk-only class-specific requests */
1305 if (transport_is_bbb()) {
1306 switch (ctrl->bRequest) {
1308 case USB_BULK_RESET_REQUEST:
1309 if (ctrl->bRequestType != (USB_DIR_OUT |
1310 USB_TYPE_CLASS | USB_RECIP_INTERFACE))
1317 /* Raise an exception to stop the current operation
1318 * and reinitialize our state. */
1319 DBG(fsg, "bulk reset request\n");
1320 raise_exception(fsg, FSG_STATE_RESET);
1321 value = DELAYED_STATUS;
1324 case USB_BULK_GET_MAX_LUN_REQUEST:
1325 if (ctrl->bRequestType != (USB_DIR_IN |
1326 USB_TYPE_CLASS | USB_RECIP_INTERFACE))
1332 VDBG(fsg, "get max LUN\n");
1333 *(u8 *) req->buf = fsg->nluns - 1;
1339 /* Handle CBI class-specific requests */
1341 switch (ctrl->bRequest) {
1343 case USB_CBI_ADSC_REQUEST:
1344 if (ctrl->bRequestType != (USB_DIR_OUT |
1345 USB_TYPE_CLASS | USB_RECIP_INTERFACE))
1351 if (w_length > MAX_COMMAND_SIZE) {
1356 fsg->ep0req->context = received_cbi_adsc;
1361 if (value == -EOPNOTSUPP)
1363 "unknown class-specific control req "
1364 "%02x.%02x v%04x i%04x l%u\n",
1365 ctrl->bRequestType, ctrl->bRequest,
1366 le16_to_cpu(ctrl->wValue), w_index, w_length);
1371 /*-------------------------------------------------------------------------*/
1373 /* Ep0 standard request handlers. These always run in_irq. */
1375 static int standard_setup_req(struct fsg_dev *fsg,
1376 const struct usb_ctrlrequest *ctrl)
1378 struct usb_request *req = fsg->ep0req;
1379 int value = -EOPNOTSUPP;
1380 u16 w_index = le16_to_cpu(ctrl->wIndex);
1381 u16 w_value = le16_to_cpu(ctrl->wValue);
1383 /* Usually this just stores reply data in the pre-allocated ep0 buffer,
1384 * but config change events will also reconfigure hardware. */
1385 switch (ctrl->bRequest) {
1387 case USB_REQ_GET_DESCRIPTOR:
1388 if (ctrl->bRequestType != (USB_DIR_IN | USB_TYPE_STANDARD |
1391 switch (w_value >> 8) {
1394 VDBG(fsg, "get device descriptor\n");
1395 value = sizeof device_desc;
1396 memcpy(req->buf, &device_desc, value);
1398 #ifdef CONFIG_USB_GADGET_DUALSPEED
1399 case USB_DT_DEVICE_QUALIFIER:
1400 VDBG(fsg, "get device qualifier\n");
1401 if (!fsg->gadget->is_dualspeed)
1403 value = sizeof dev_qualifier;
1404 memcpy(req->buf, &dev_qualifier, value);
1407 case USB_DT_OTHER_SPEED_CONFIG:
1408 VDBG(fsg, "get other-speed config descriptor\n");
1409 if (!fsg->gadget->is_dualspeed)
1414 VDBG(fsg, "get configuration descriptor\n");
1415 #ifdef CONFIG_USB_GADGET_DUALSPEED
1418 value = populate_config_buf(fsg->gadget,
1425 VDBG(fsg, "get string descriptor\n");
1427 /* wIndex == language code */
1428 value = usb_gadget_get_string(&stringtab,
1429 w_value & 0xff, req->buf);
1434 /* One config, two speeds */
1435 case USB_REQ_SET_CONFIGURATION:
1436 if (ctrl->bRequestType != (USB_DIR_OUT | USB_TYPE_STANDARD |
1439 VDBG(fsg, "set configuration\n");
1440 if (w_value == CONFIG_VALUE || w_value == 0) {
1441 fsg->new_config = w_value;
1443 /* Raise an exception to wipe out previous transaction
1444 * state (queued bufs, etc) and set the new config. */
1445 raise_exception(fsg, FSG_STATE_CONFIG_CHANGE);
1446 value = DELAYED_STATUS;
1449 case USB_REQ_GET_CONFIGURATION:
1450 if (ctrl->bRequestType != (USB_DIR_IN | USB_TYPE_STANDARD |
1453 VDBG(fsg, "get configuration\n");
1454 *(u8 *) req->buf = fsg->config;
1458 case USB_REQ_SET_INTERFACE:
1459 if (ctrl->bRequestType != (USB_DIR_OUT| USB_TYPE_STANDARD |
1460 USB_RECIP_INTERFACE))
1462 if (fsg->config && w_index == 0) {
1464 /* Raise an exception to wipe out previous transaction
1465 * state (queued bufs, etc) and install the new
1466 * interface altsetting. */
1467 raise_exception(fsg, FSG_STATE_INTERFACE_CHANGE);
1468 value = DELAYED_STATUS;
1471 case USB_REQ_GET_INTERFACE:
1472 if (ctrl->bRequestType != (USB_DIR_IN | USB_TYPE_STANDARD |
1473 USB_RECIP_INTERFACE))
1481 VDBG(fsg, "get interface\n");
1482 *(u8 *) req->buf = 0;
1488 "unknown control req %02x.%02x v%04x i%04x l%u\n",
1489 ctrl->bRequestType, ctrl->bRequest,
1490 w_value, w_index, le16_to_cpu(ctrl->wLength));
1497 static int fsg_setup(struct usb_gadget *gadget,
1498 const struct usb_ctrlrequest *ctrl)
1500 struct fsg_dev *fsg = get_gadget_data(gadget);
1502 int w_length = le16_to_cpu(ctrl->wLength);
1504 ++fsg->ep0_req_tag; // Record arrival of a new request
1505 fsg->ep0req->context = NULL;
1506 fsg->ep0req->length = 0;
1507 dump_msg(fsg, "ep0-setup", (u8 *) ctrl, sizeof(*ctrl));
1509 if ((ctrl->bRequestType & USB_TYPE_MASK) == USB_TYPE_CLASS)
1510 rc = class_setup_req(fsg, ctrl);
1512 rc = standard_setup_req(fsg, ctrl);
1514 /* Respond with data/status or defer until later? */
1515 if (rc >= 0 && rc != DELAYED_STATUS) {
1516 rc = min(rc, w_length);
1517 fsg->ep0req->length = rc;
1518 fsg->ep0req->zero = rc < w_length;
1519 fsg->ep0req_name = (ctrl->bRequestType & USB_DIR_IN ?
1520 "ep0-in" : "ep0-out");
1521 rc = ep0_queue(fsg);
1524 /* Device either stalls (rc < 0) or reports success */
1529 /*-------------------------------------------------------------------------*/
1531 /* All the following routines run in process context */
1534 /* Use this for bulk or interrupt transfers, not ep0 */
1535 static void start_transfer(struct fsg_dev *fsg, struct usb_ep *ep,
1536 struct usb_request *req, int *pbusy,
1537 enum fsg_buffer_state *state)
1541 if (ep == fsg->bulk_in)
1542 dump_msg(fsg, "bulk-in", req->buf, req->length);
1543 else if (ep == fsg->intr_in)
1544 dump_msg(fsg, "intr-in", req->buf, req->length);
1546 spin_lock_irq(&fsg->lock);
1548 *state = BUF_STATE_BUSY;
1549 spin_unlock_irq(&fsg->lock);
1550 rc = usb_ep_queue(ep, req, GFP_KERNEL);
1553 *state = BUF_STATE_EMPTY;
1555 /* We can't do much more than wait for a reset */
1557 /* Note: currently the net2280 driver fails zero-length
1558 * submissions if DMA is enabled. */
1559 if (rc != -ESHUTDOWN && !(rc == -EOPNOTSUPP &&
1561 WARN(fsg, "error in submission: %s --> %d\n",
1567 static int sleep_thread(struct fsg_dev *fsg)
1571 /* Wait until a signal arrives or we are woken up */
1574 set_current_state(TASK_INTERRUPTIBLE);
1575 if (signal_pending(current)) {
1579 if (fsg->thread_wakeup_needed)
1583 __set_current_state(TASK_RUNNING);
1584 fsg->thread_wakeup_needed = 0;
1589 /*-------------------------------------------------------------------------*/
1591 static int do_read(struct fsg_dev *fsg)
1593 struct lun *curlun = fsg->curlun;
1595 struct fsg_buffhd *bh;
1598 loff_t file_offset, file_offset_tmp;
1599 unsigned int amount;
1600 unsigned int partial_page;
1603 /* Get the starting Logical Block Address and check that it's
1605 if (fsg->cmnd[0] == SC_READ_6)
1606 lba = (fsg->cmnd[1] << 16) | get_be16(&fsg->cmnd[2]);
1608 lba = get_be32(&fsg->cmnd[2]);
1610 /* We allow DPO (Disable Page Out = don't save data in the
1611 * cache) and FUA (Force Unit Access = don't read from the
1612 * cache), but we don't implement them. */
1613 if ((fsg->cmnd[1] & ~0x18) != 0) {
1614 curlun->sense_data = SS_INVALID_FIELD_IN_CDB;
1618 if (lba >= curlun->num_sectors) {
1619 curlun->sense_data = SS_LOGICAL_BLOCK_ADDRESS_OUT_OF_RANGE;
1622 file_offset = ((loff_t) lba) << 9;
1624 /* Carry out the file reads */
1625 amount_left = fsg->data_size_from_cmnd;
1626 if (unlikely(amount_left == 0))
1627 return -EIO; // No default reply
1631 /* Figure out how much we need to read:
1632 * Try to read the remaining amount.
1633 * But don't read more than the buffer size.
1634 * And don't try to read past the end of the file.
1635 * Finally, if we're not at a page boundary, don't read past
1637 * If this means reading 0 then we were asked to read past
1638 * the end of file. */
1639 amount = min((unsigned int) amount_left, mod_data.buflen);
1640 amount = min((loff_t) amount,
1641 curlun->file_length - file_offset);
1642 partial_page = file_offset & (PAGE_CACHE_SIZE - 1);
1643 if (partial_page > 0)
1644 amount = min(amount, (unsigned int) PAGE_CACHE_SIZE -
1647 /* Wait for the next buffer to become available */
1648 bh = fsg->next_buffhd_to_fill;
1649 while (bh->state != BUF_STATE_EMPTY) {
1650 if ((rc = sleep_thread(fsg)) != 0)
1654 /* If we were asked to read past the end of file,
1655 * end with an empty buffer. */
1657 curlun->sense_data =
1658 SS_LOGICAL_BLOCK_ADDRESS_OUT_OF_RANGE;
1659 curlun->sense_data_info = file_offset >> 9;
1660 curlun->info_valid = 1;
1661 bh->inreq->length = 0;
1662 bh->state = BUF_STATE_FULL;
1666 /* Perform the read */
1667 file_offset_tmp = file_offset;
1668 nread = vfs_read(curlun->filp,
1669 (char __user *) bh->buf,
1670 amount, &file_offset_tmp);
1671 VLDBG(curlun, "file read %u @ %llu -> %d\n", amount,
1672 (unsigned long long) file_offset,
1674 if (signal_pending(current))
1678 LDBG(curlun, "error in file read: %d\n",
1681 } else if (nread < amount) {
1682 LDBG(curlun, "partial file read: %d/%u\n",
1683 (int) nread, amount);
1684 nread -= (nread & 511); // Round down to a block
1686 file_offset += nread;
1687 amount_left -= nread;
1688 fsg->residue -= nread;
1689 bh->inreq->length = nread;
1690 bh->state = BUF_STATE_FULL;
1692 /* If an error occurred, report it and its position */
1693 if (nread < amount) {
1694 curlun->sense_data = SS_UNRECOVERED_READ_ERROR;
1695 curlun->sense_data_info = file_offset >> 9;
1696 curlun->info_valid = 1;
1700 if (amount_left == 0)
1701 break; // No more left to read
1703 /* Send this buffer and go read some more */
1704 bh->inreq->zero = 0;
1705 start_transfer(fsg, fsg->bulk_in, bh->inreq,
1706 &bh->inreq_busy, &bh->state);
1707 fsg->next_buffhd_to_fill = bh->next;
1710 return -EIO; // No default reply
1714 /*-------------------------------------------------------------------------*/
1716 static int do_write(struct fsg_dev *fsg)
1718 struct lun *curlun = fsg->curlun;
1720 struct fsg_buffhd *bh;
1722 u32 amount_left_to_req, amount_left_to_write;
1723 loff_t usb_offset, file_offset, file_offset_tmp;
1724 unsigned int amount;
1725 unsigned int partial_page;
1730 curlun->sense_data = SS_WRITE_PROTECTED;
1733 curlun->filp->f_flags &= ~O_SYNC; // Default is not to wait
1735 /* Get the starting Logical Block Address and check that it's
1737 if (fsg->cmnd[0] == SC_WRITE_6)
1738 lba = (fsg->cmnd[1] << 16) | get_be16(&fsg->cmnd[2]);
1740 lba = get_be32(&fsg->cmnd[2]);
1742 /* We allow DPO (Disable Page Out = don't save data in the
1743 * cache) and FUA (Force Unit Access = write directly to the
1744 * medium). We don't implement DPO; we implement FUA by
1745 * performing synchronous output. */
1746 if ((fsg->cmnd[1] & ~0x18) != 0) {
1747 curlun->sense_data = SS_INVALID_FIELD_IN_CDB;
1750 if (fsg->cmnd[1] & 0x08) // FUA
1751 curlun->filp->f_flags |= O_SYNC;
1753 if (lba >= curlun->num_sectors) {
1754 curlun->sense_data = SS_LOGICAL_BLOCK_ADDRESS_OUT_OF_RANGE;
1758 /* Carry out the file writes */
1760 file_offset = usb_offset = ((loff_t) lba) << 9;
1761 amount_left_to_req = amount_left_to_write = fsg->data_size_from_cmnd;
1763 while (amount_left_to_write > 0) {
1765 /* Queue a request for more data from the host */
1766 bh = fsg->next_buffhd_to_fill;
1767 if (bh->state == BUF_STATE_EMPTY && get_some_more) {
1769 /* Figure out how much we want to get:
1770 * Try to get the remaining amount.
1771 * But don't get more than the buffer size.
1772 * And don't try to go past the end of the file.
1773 * If we're not at a page boundary,
1774 * don't go past the next page.
1775 * If this means getting 0, then we were asked
1776 * to write past the end of file.
1777 * Finally, round down to a block boundary. */
1778 amount = min(amount_left_to_req, mod_data.buflen);
1779 amount = min((loff_t) amount, curlun->file_length -
1781 partial_page = usb_offset & (PAGE_CACHE_SIZE - 1);
1782 if (partial_page > 0)
1783 amount = min(amount,
1784 (unsigned int) PAGE_CACHE_SIZE - partial_page);
1788 curlun->sense_data =
1789 SS_LOGICAL_BLOCK_ADDRESS_OUT_OF_RANGE;
1790 curlun->sense_data_info = usb_offset >> 9;
1791 curlun->info_valid = 1;
1794 amount -= (amount & 511);
1797 /* Why were we were asked to transfer a
1803 /* Get the next buffer */
1804 usb_offset += amount;
1805 fsg->usb_amount_left -= amount;
1806 amount_left_to_req -= amount;
1807 if (amount_left_to_req == 0)
1810 /* amount is always divisible by 512, hence by
1811 * the bulk-out maxpacket size */
1812 bh->outreq->length = bh->bulk_out_intended_length =
1814 bh->outreq->short_not_ok = 1;
1815 start_transfer(fsg, fsg->bulk_out, bh->outreq,
1816 &bh->outreq_busy, &bh->state);
1817 fsg->next_buffhd_to_fill = bh->next;
1821 /* Write the received data to the backing file */
1822 bh = fsg->next_buffhd_to_drain;
1823 if (bh->state == BUF_STATE_EMPTY && !get_some_more)
1824 break; // We stopped early
1825 if (bh->state == BUF_STATE_FULL) {
1827 fsg->next_buffhd_to_drain = bh->next;
1828 bh->state = BUF_STATE_EMPTY;
1830 /* Did something go wrong with the transfer? */
1831 if (bh->outreq->status != 0) {
1832 curlun->sense_data = SS_COMMUNICATION_FAILURE;
1833 curlun->sense_data_info = file_offset >> 9;
1834 curlun->info_valid = 1;
1838 amount = bh->outreq->actual;
1839 if (curlun->file_length - file_offset < amount) {
1841 "write %u @ %llu beyond end %llu\n",
1842 amount, (unsigned long long) file_offset,
1843 (unsigned long long) curlun->file_length);
1844 amount = curlun->file_length - file_offset;
1847 /* Perform the write */
1848 file_offset_tmp = file_offset;
1849 nwritten = vfs_write(curlun->filp,
1850 (char __user *) bh->buf,
1851 amount, &file_offset_tmp);
1852 VLDBG(curlun, "file write %u @ %llu -> %d\n", amount,
1853 (unsigned long long) file_offset,
1855 if (signal_pending(current))
1856 return -EINTR; // Interrupted!
1859 LDBG(curlun, "error in file write: %d\n",
1862 } else if (nwritten < amount) {
1863 LDBG(curlun, "partial file write: %d/%u\n",
1864 (int) nwritten, amount);
1865 nwritten -= (nwritten & 511);
1866 // Round down to a block
1868 file_offset += nwritten;
1869 amount_left_to_write -= nwritten;
1870 fsg->residue -= nwritten;
1872 /* If an error occurred, report it and its position */
1873 if (nwritten < amount) {
1874 curlun->sense_data = SS_WRITE_ERROR;
1875 curlun->sense_data_info = file_offset >> 9;
1876 curlun->info_valid = 1;
1880 /* Did the host decide to stop early? */
1881 if (bh->outreq->actual != bh->outreq->length) {
1882 fsg->short_packet_received = 1;
1888 /* Wait for something to happen */
1889 if ((rc = sleep_thread(fsg)) != 0)
1893 return -EIO; // No default reply
1897 /*-------------------------------------------------------------------------*/
1899 /* Sync the file data, don't bother with the metadata.
1900 * This code was copied from fs/buffer.c:sys_fdatasync(). */
1901 static int fsync_sub(struct lun *curlun)
1903 struct file *filp = curlun->filp;
1904 struct inode *inode;
1907 if (curlun->ro || !filp)
1909 if (!filp->f_op->fsync)
1912 inode = filp->f_dentry->d_inode;
1913 mutex_lock(&inode->i_mutex);
1914 rc = filemap_fdatawrite(inode->i_mapping);
1915 err = filp->f_op->fsync(filp, filp->f_dentry, 1);
1918 err = filemap_fdatawait(inode->i_mapping);
1921 mutex_unlock(&inode->i_mutex);
1922 VLDBG(curlun, "fdatasync -> %d\n", rc);
1926 static void fsync_all(struct fsg_dev *fsg)
1930 for (i = 0; i < fsg->nluns; ++i)
1931 fsync_sub(&fsg->luns[i]);
1934 static int do_synchronize_cache(struct fsg_dev *fsg)
1936 struct lun *curlun = fsg->curlun;
1939 /* We ignore the requested LBA and write out all file's
1940 * dirty data buffers. */
1941 rc = fsync_sub(curlun);
1943 curlun->sense_data = SS_WRITE_ERROR;
1948 /*-------------------------------------------------------------------------*/
1950 static void invalidate_sub(struct lun *curlun)
1952 struct file *filp = curlun->filp;
1953 struct inode *inode = filp->f_dentry->d_inode;
1956 rc = invalidate_inode_pages(inode->i_mapping);
1957 VLDBG(curlun, "invalidate_inode_pages -> %ld\n", rc);
1960 static int do_verify(struct fsg_dev *fsg)
1962 struct lun *curlun = fsg->curlun;
1964 u32 verification_length;
1965 struct fsg_buffhd *bh = fsg->next_buffhd_to_fill;
1966 loff_t file_offset, file_offset_tmp;
1968 unsigned int amount;
1971 /* Get the starting Logical Block Address and check that it's
1973 lba = get_be32(&fsg->cmnd[2]);
1974 if (lba >= curlun->num_sectors) {
1975 curlun->sense_data = SS_LOGICAL_BLOCK_ADDRESS_OUT_OF_RANGE;
1979 /* We allow DPO (Disable Page Out = don't save data in the
1980 * cache) but we don't implement it. */
1981 if ((fsg->cmnd[1] & ~0x10) != 0) {
1982 curlun->sense_data = SS_INVALID_FIELD_IN_CDB;
1986 verification_length = get_be16(&fsg->cmnd[7]);
1987 if (unlikely(verification_length == 0))
1988 return -EIO; // No default reply
1990 /* Prepare to carry out the file verify */
1991 amount_left = verification_length << 9;
1992 file_offset = ((loff_t) lba) << 9;
1994 /* Write out all the dirty buffers before invalidating them */
1996 if (signal_pending(current))
1999 invalidate_sub(curlun);
2000 if (signal_pending(current))
2003 /* Just try to read the requested blocks */
2004 while (amount_left > 0) {
2006 /* Figure out how much we need to read:
2007 * Try to read the remaining amount, but not more than
2009 * And don't try to read past the end of the file.
2010 * If this means reading 0 then we were asked to read
2011 * past the end of file. */
2012 amount = min((unsigned int) amount_left, mod_data.buflen);
2013 amount = min((loff_t) amount,
2014 curlun->file_length - file_offset);
2016 curlun->sense_data =
2017 SS_LOGICAL_BLOCK_ADDRESS_OUT_OF_RANGE;
2018 curlun->sense_data_info = file_offset >> 9;
2019 curlun->info_valid = 1;
2023 /* Perform the read */
2024 file_offset_tmp = file_offset;
2025 nread = vfs_read(curlun->filp,
2026 (char __user *) bh->buf,
2027 amount, &file_offset_tmp);
2028 VLDBG(curlun, "file read %u @ %llu -> %d\n", amount,
2029 (unsigned long long) file_offset,
2031 if (signal_pending(current))
2035 LDBG(curlun, "error in file verify: %d\n",
2038 } else if (nread < amount) {
2039 LDBG(curlun, "partial file verify: %d/%u\n",
2040 (int) nread, amount);
2041 nread -= (nread & 511); // Round down to a sector
2044 curlun->sense_data = SS_UNRECOVERED_READ_ERROR;
2045 curlun->sense_data_info = file_offset >> 9;
2046 curlun->info_valid = 1;
2049 file_offset += nread;
2050 amount_left -= nread;
2056 /*-------------------------------------------------------------------------*/
2058 static int do_inquiry(struct fsg_dev *fsg, struct fsg_buffhd *bh)
2060 u8 *buf = (u8 *) bh->buf;
2062 static char vendor_id[] = "Linux ";
2063 static char product_id[] = "File-Stor Gadget";
2065 if (!fsg->curlun) { // Unsupported LUNs are okay
2066 fsg->bad_lun_okay = 1;
2068 buf[0] = 0x7f; // Unsupported, no device-type
2072 memset(buf, 0, 8); // Non-removable, direct-access device
2073 if (mod_data.removable)
2075 buf[2] = 2; // ANSI SCSI level 2
2076 buf[3] = 2; // SCSI-2 INQUIRY data format
2077 buf[4] = 31; // Additional length
2078 // No special options
2079 sprintf(buf + 8, "%-8s%-16s%04x", vendor_id, product_id,
2085 static int do_request_sense(struct fsg_dev *fsg, struct fsg_buffhd *bh)
2087 struct lun *curlun = fsg->curlun;
2088 u8 *buf = (u8 *) bh->buf;
2093 * From the SCSI-2 spec., section 7.9 (Unit attention condition):
2095 * If a REQUEST SENSE command is received from an initiator
2096 * with a pending unit attention condition (before the target
2097 * generates the contingent allegiance condition), then the
2098 * target shall either:
2099 * a) report any pending sense data and preserve the unit
2100 * attention condition on the logical unit, or,
2101 * b) report the unit attention condition, may discard any
2102 * pending sense data, and clear the unit attention
2103 * condition on the logical unit for that initiator.
2105 * FSG normally uses option a); enable this code to use option b).
2108 if (curlun && curlun->unit_attention_data != SS_NO_SENSE) {
2109 curlun->sense_data = curlun->unit_attention_data;
2110 curlun->unit_attention_data = SS_NO_SENSE;
2114 if (!curlun) { // Unsupported LUNs are okay
2115 fsg->bad_lun_okay = 1;
2116 sd = SS_LOGICAL_UNIT_NOT_SUPPORTED;
2120 sd = curlun->sense_data;
2121 sdinfo = curlun->sense_data_info;
2122 valid = curlun->info_valid << 7;
2123 curlun->sense_data = SS_NO_SENSE;
2124 curlun->sense_data_info = 0;
2125 curlun->info_valid = 0;
2129 buf[0] = valid | 0x70; // Valid, current error
2131 put_be32(&buf[3], sdinfo); // Sense information
2132 buf[7] = 18 - 8; // Additional sense length
2139 static int do_read_capacity(struct fsg_dev *fsg, struct fsg_buffhd *bh)
2141 struct lun *curlun = fsg->curlun;
2142 u32 lba = get_be32(&fsg->cmnd[2]);
2143 int pmi = fsg->cmnd[8];
2144 u8 *buf = (u8 *) bh->buf;
2146 /* Check the PMI and LBA fields */
2147 if (pmi > 1 || (pmi == 0 && lba != 0)) {
2148 curlun->sense_data = SS_INVALID_FIELD_IN_CDB;
2152 put_be32(&buf[0], curlun->num_sectors - 1); // Max logical block
2153 put_be32(&buf[4], 512); // Block length
2158 static int do_mode_sense(struct fsg_dev *fsg, struct fsg_buffhd *bh)
2160 struct lun *curlun = fsg->curlun;
2161 int mscmnd = fsg->cmnd[0];
2162 u8 *buf = (u8 *) bh->buf;
2165 int changeable_values, all_pages;
2169 if ((fsg->cmnd[1] & ~0x08) != 0) { // Mask away DBD
2170 curlun->sense_data = SS_INVALID_FIELD_IN_CDB;
2173 pc = fsg->cmnd[2] >> 6;
2174 page_code = fsg->cmnd[2] & 0x3f;
2176 curlun->sense_data = SS_SAVING_PARAMETERS_NOT_SUPPORTED;
2179 changeable_values = (pc == 1);
2180 all_pages = (page_code == 0x3f);
2182 /* Write the mode parameter header. Fixed values are: default
2183 * medium type, no cache control (DPOFUA), and no block descriptors.
2184 * The only variable value is the WriteProtect bit. We will fill in
2185 * the mode data length later. */
2187 if (mscmnd == SC_MODE_SENSE_6) {
2188 buf[2] = (curlun->ro ? 0x80 : 0x00); // WP, DPOFUA
2191 } else { // SC_MODE_SENSE_10
2192 buf[3] = (curlun->ro ? 0x80 : 0x00); // WP, DPOFUA
2194 limit = 65535; // Should really be mod_data.buflen
2197 /* No block descriptors */
2199 /* The mode pages, in numerical order. The only page we support
2200 * is the Caching page. */
2201 if (page_code == 0x08 || all_pages) {
2203 buf[0] = 0x08; // Page code
2204 buf[1] = 10; // Page length
2205 memset(buf+2, 0, 10); // None of the fields are changeable
2207 if (!changeable_values) {
2208 buf[2] = 0x04; // Write cache enable,
2209 // Read cache not disabled
2210 // No cache retention priorities
2211 put_be16(&buf[4], 0xffff); // Don't disable prefetch
2212 // Minimum prefetch = 0
2213 put_be16(&buf[8], 0xffff); // Maximum prefetch
2214 put_be16(&buf[10], 0xffff); // Maximum prefetch ceiling
2219 /* Check that a valid page was requested and the mode data length
2220 * isn't too long. */
2222 if (!valid_page || len > limit) {
2223 curlun->sense_data = SS_INVALID_FIELD_IN_CDB;
2227 /* Store the mode data length */
2228 if (mscmnd == SC_MODE_SENSE_6)
2231 put_be16(buf0, len - 2);
2236 static int do_start_stop(struct fsg_dev *fsg)
2238 struct lun *curlun = fsg->curlun;
2241 if (!mod_data.removable) {
2242 curlun->sense_data = SS_INVALID_COMMAND;
2246 // int immed = fsg->cmnd[1] & 0x01;
2247 loej = fsg->cmnd[4] & 0x02;
2248 start = fsg->cmnd[4] & 0x01;
2250 #ifdef CONFIG_USB_FILE_STORAGE_TEST
2251 if ((fsg->cmnd[1] & ~0x01) != 0 || // Mask away Immed
2252 (fsg->cmnd[4] & ~0x03) != 0) { // Mask LoEj, Start
2253 curlun->sense_data = SS_INVALID_FIELD_IN_CDB;
2259 /* Are we allowed to unload the media? */
2260 if (curlun->prevent_medium_removal) {
2261 LDBG(curlun, "unload attempt prevented\n");
2262 curlun->sense_data = SS_MEDIUM_REMOVAL_PREVENTED;
2265 if (loej) { // Simulate an unload/eject
2266 up_read(&fsg->filesem);
2267 down_write(&fsg->filesem);
2268 close_backing_file(curlun);
2269 up_write(&fsg->filesem);
2270 down_read(&fsg->filesem);
2274 /* Our emulation doesn't support mounting; the medium is
2275 * available for use as soon as it is loaded. */
2276 if (!backing_file_is_open(curlun)) {
2277 curlun->sense_data = SS_MEDIUM_NOT_PRESENT;
2286 static int do_prevent_allow(struct fsg_dev *fsg)
2288 struct lun *curlun = fsg->curlun;
2291 if (!mod_data.removable) {
2292 curlun->sense_data = SS_INVALID_COMMAND;
2296 prevent = fsg->cmnd[4] & 0x01;
2297 if ((fsg->cmnd[4] & ~0x01) != 0) { // Mask away Prevent
2298 curlun->sense_data = SS_INVALID_FIELD_IN_CDB;
2302 if (curlun->prevent_medium_removal && !prevent)
2304 curlun->prevent_medium_removal = prevent;
2309 static int do_read_format_capacities(struct fsg_dev *fsg,
2310 struct fsg_buffhd *bh)
2312 struct lun *curlun = fsg->curlun;
2313 u8 *buf = (u8 *) bh->buf;
2315 buf[0] = buf[1] = buf[2] = 0;
2316 buf[3] = 8; // Only the Current/Maximum Capacity Descriptor
2319 put_be32(&buf[0], curlun->num_sectors); // Number of blocks
2320 put_be32(&buf[4], 512); // Block length
2321 buf[4] = 0x02; // Current capacity
2326 static int do_mode_select(struct fsg_dev *fsg, struct fsg_buffhd *bh)
2328 struct lun *curlun = fsg->curlun;
2330 /* We don't support MODE SELECT */
2331 curlun->sense_data = SS_INVALID_COMMAND;
2336 /*-------------------------------------------------------------------------*/
2338 static int halt_bulk_in_endpoint(struct fsg_dev *fsg)
2342 rc = fsg_set_halt(fsg, fsg->bulk_in);
2344 VDBG(fsg, "delayed bulk-in endpoint halt\n");
2346 if (rc != -EAGAIN) {
2347 WARN(fsg, "usb_ep_set_halt -> %d\n", rc);
2352 /* Wait for a short time and then try again */
2353 if (msleep_interruptible(100) != 0)
2355 rc = usb_ep_set_halt(fsg->bulk_in);
2360 static int pad_with_zeros(struct fsg_dev *fsg)
2362 struct fsg_buffhd *bh = fsg->next_buffhd_to_fill;
2363 u32 nkeep = bh->inreq->length;
2367 bh->state = BUF_STATE_EMPTY; // For the first iteration
2368 fsg->usb_amount_left = nkeep + fsg->residue;
2369 while (fsg->usb_amount_left > 0) {
2371 /* Wait for the next buffer to be free */
2372 while (bh->state != BUF_STATE_EMPTY) {
2373 if ((rc = sleep_thread(fsg)) != 0)
2377 nsend = min(fsg->usb_amount_left, (u32) mod_data.buflen);
2378 memset(bh->buf + nkeep, 0, nsend - nkeep);
2379 bh->inreq->length = nsend;
2380 bh->inreq->zero = 0;
2381 start_transfer(fsg, fsg->bulk_in, bh->inreq,
2382 &bh->inreq_busy, &bh->state);
2383 bh = fsg->next_buffhd_to_fill = bh->next;
2384 fsg->usb_amount_left -= nsend;
2390 static int throw_away_data(struct fsg_dev *fsg)
2392 struct fsg_buffhd *bh;
2396 while ((bh = fsg->next_buffhd_to_drain)->state != BUF_STATE_EMPTY ||
2397 fsg->usb_amount_left > 0) {
2399 /* Throw away the data in a filled buffer */
2400 if (bh->state == BUF_STATE_FULL) {
2402 bh->state = BUF_STATE_EMPTY;
2403 fsg->next_buffhd_to_drain = bh->next;
2405 /* A short packet or an error ends everything */
2406 if (bh->outreq->actual != bh->outreq->length ||
2407 bh->outreq->status != 0) {
2408 raise_exception(fsg, FSG_STATE_ABORT_BULK_OUT);
2414 /* Try to submit another request if we need one */
2415 bh = fsg->next_buffhd_to_fill;
2416 if (bh->state == BUF_STATE_EMPTY && fsg->usb_amount_left > 0) {
2417 amount = min(fsg->usb_amount_left,
2418 (u32) mod_data.buflen);
2420 /* amount is always divisible by 512, hence by
2421 * the bulk-out maxpacket size */
2422 bh->outreq->length = bh->bulk_out_intended_length =
2424 bh->outreq->short_not_ok = 1;
2425 start_transfer(fsg, fsg->bulk_out, bh->outreq,
2426 &bh->outreq_busy, &bh->state);
2427 fsg->next_buffhd_to_fill = bh->next;
2428 fsg->usb_amount_left -= amount;
2432 /* Otherwise wait for something to happen */
2433 if ((rc = sleep_thread(fsg)) != 0)
2440 static int finish_reply(struct fsg_dev *fsg)
2442 struct fsg_buffhd *bh = fsg->next_buffhd_to_fill;
2445 switch (fsg->data_dir) {
2447 break; // Nothing to send
2449 /* If we don't know whether the host wants to read or write,
2450 * this must be CB or CBI with an unknown command. We mustn't
2451 * try to send or receive any data. So stall both bulk pipes
2452 * if we can and wait for a reset. */
2453 case DATA_DIR_UNKNOWN:
2454 if (mod_data.can_stall) {
2455 fsg_set_halt(fsg, fsg->bulk_out);
2456 rc = halt_bulk_in_endpoint(fsg);
2460 /* All but the last buffer of data must have already been sent */
2461 case DATA_DIR_TO_HOST:
2462 if (fsg->data_size == 0)
2463 ; // Nothing to send
2465 /* If there's no residue, simply send the last buffer */
2466 else if (fsg->residue == 0) {
2467 bh->inreq->zero = 0;
2468 start_transfer(fsg, fsg->bulk_in, bh->inreq,
2469 &bh->inreq_busy, &bh->state);
2470 fsg->next_buffhd_to_fill = bh->next;
2473 /* There is a residue. For CB and CBI, simply mark the end
2474 * of the data with a short packet. However, if we are
2475 * allowed to stall, there was no data at all (residue ==
2476 * data_size), and the command failed (invalid LUN or
2477 * sense data is set), then halt the bulk-in endpoint
2479 else if (!transport_is_bbb()) {
2480 if (mod_data.can_stall &&
2481 fsg->residue == fsg->data_size &&
2482 (!fsg->curlun || fsg->curlun->sense_data != SS_NO_SENSE)) {
2483 bh->state = BUF_STATE_EMPTY;
2484 rc = halt_bulk_in_endpoint(fsg);
2486 bh->inreq->zero = 1;
2487 start_transfer(fsg, fsg->bulk_in, bh->inreq,
2488 &bh->inreq_busy, &bh->state);
2489 fsg->next_buffhd_to_fill = bh->next;
2493 /* For Bulk-only, if we're allowed to stall then send the
2494 * short packet and halt the bulk-in endpoint. If we can't
2495 * stall, pad out the remaining data with 0's. */
2497 if (mod_data.can_stall) {
2498 bh->inreq->zero = 1;
2499 start_transfer(fsg, fsg->bulk_in, bh->inreq,
2500 &bh->inreq_busy, &bh->state);
2501 fsg->next_buffhd_to_fill = bh->next;
2502 rc = halt_bulk_in_endpoint(fsg);
2504 rc = pad_with_zeros(fsg);
2508 /* We have processed all we want from the data the host has sent.
2509 * There may still be outstanding bulk-out requests. */
2510 case DATA_DIR_FROM_HOST:
2511 if (fsg->residue == 0)
2512 ; // Nothing to receive
2514 /* Did the host stop sending unexpectedly early? */
2515 else if (fsg->short_packet_received) {
2516 raise_exception(fsg, FSG_STATE_ABORT_BULK_OUT);
2520 /* We haven't processed all the incoming data. Even though
2521 * we may be allowed to stall, doing so would cause a race.
2522 * The controller may already have ACK'ed all the remaining
2523 * bulk-out packets, in which case the host wouldn't see a
2524 * STALL. Not realizing the endpoint was halted, it wouldn't
2525 * clear the halt -- leading to problems later on. */
2527 else if (mod_data.can_stall) {
2528 fsg_set_halt(fsg, fsg->bulk_out);
2529 raise_exception(fsg, FSG_STATE_ABORT_BULK_OUT);
2534 /* We can't stall. Read in the excess data and throw it
2537 rc = throw_away_data(fsg);
2544 static int send_status(struct fsg_dev *fsg)
2546 struct lun *curlun = fsg->curlun;
2547 struct fsg_buffhd *bh;
2549 u8 status = USB_STATUS_PASS;
2552 /* Wait for the next buffer to become available */
2553 bh = fsg->next_buffhd_to_fill;
2554 while (bh->state != BUF_STATE_EMPTY) {
2555 if ((rc = sleep_thread(fsg)) != 0)
2560 sd = curlun->sense_data;
2561 sdinfo = curlun->sense_data_info;
2562 } else if (fsg->bad_lun_okay)
2565 sd = SS_LOGICAL_UNIT_NOT_SUPPORTED;
2567 if (fsg->phase_error) {
2568 DBG(fsg, "sending phase-error status\n");
2569 status = USB_STATUS_PHASE_ERROR;
2570 sd = SS_INVALID_COMMAND;
2571 } else if (sd != SS_NO_SENSE) {
2572 DBG(fsg, "sending command-failure status\n");
2573 status = USB_STATUS_FAIL;
2574 VDBG(fsg, " sense data: SK x%02x, ASC x%02x, ASCQ x%02x;"
2576 SK(sd), ASC(sd), ASCQ(sd), sdinfo);
2579 if (transport_is_bbb()) {
2580 struct bulk_cs_wrap *csw = (struct bulk_cs_wrap *) bh->buf;
2582 /* Store and send the Bulk-only CSW */
2583 csw->Signature = __constant_cpu_to_le32(USB_BULK_CS_SIG);
2584 csw->Tag = fsg->tag;
2585 csw->Residue = cpu_to_le32(fsg->residue);
2586 csw->Status = status;
2588 bh->inreq->length = USB_BULK_CS_WRAP_LEN;
2589 bh->inreq->zero = 0;
2590 start_transfer(fsg, fsg->bulk_in, bh->inreq,
2591 &bh->inreq_busy, &bh->state);
2593 } else if (mod_data.transport_type == USB_PR_CB) {
2595 /* Control-Bulk transport has no status phase! */
2598 } else { // USB_PR_CBI
2599 struct interrupt_data *buf = (struct interrupt_data *)
2602 /* Store and send the Interrupt data. UFI sends the ASC
2603 * and ASCQ bytes. Everything else sends a Type (which
2604 * is always 0) and the status Value. */
2605 if (mod_data.protocol_type == USB_SC_UFI) {
2606 buf->bType = ASC(sd);
2607 buf->bValue = ASCQ(sd);
2610 buf->bValue = status;
2612 fsg->intreq->length = CBI_INTERRUPT_DATA_LEN;
2614 fsg->intr_buffhd = bh; // Point to the right buffhd
2615 fsg->intreq->buf = bh->inreq->buf;
2616 fsg->intreq->dma = bh->inreq->dma;
2617 fsg->intreq->context = bh;
2618 start_transfer(fsg, fsg->intr_in, fsg->intreq,
2619 &fsg->intreq_busy, &bh->state);
2622 fsg->next_buffhd_to_fill = bh->next;
2627 /*-------------------------------------------------------------------------*/
2629 /* Check whether the command is properly formed and whether its data size
2630 * and direction agree with the values we already have. */
2631 static int check_command(struct fsg_dev *fsg, int cmnd_size,
2632 enum data_direction data_dir, unsigned int mask,
2633 int needs_medium, const char *name)
2636 int lun = fsg->cmnd[1] >> 5;
2637 static const char dirletter[4] = {'u', 'o', 'i', 'n'};
2641 /* Adjust the expected cmnd_size for protocol encapsulation padding.
2642 * Transparent SCSI doesn't pad. */
2643 if (protocol_is_scsi())
2646 /* There's some disagreement as to whether RBC pads commands or not.
2647 * We'll play it safe and accept either form. */
2648 else if (mod_data.protocol_type == USB_SC_RBC) {
2649 if (fsg->cmnd_size == 12)
2652 /* All the other protocols pad to 12 bytes */
2657 if (fsg->data_dir != DATA_DIR_UNKNOWN)
2658 sprintf(hdlen, ", H%c=%u", dirletter[(int) fsg->data_dir],
2660 VDBG(fsg, "SCSI command: %s; Dc=%d, D%c=%u; Hc=%d%s\n",
2661 name, cmnd_size, dirletter[(int) data_dir],
2662 fsg->data_size_from_cmnd, fsg->cmnd_size, hdlen);
2664 /* We can't reply at all until we know the correct data direction
2666 if (fsg->data_size_from_cmnd == 0)
2667 data_dir = DATA_DIR_NONE;
2668 if (fsg->data_dir == DATA_DIR_UNKNOWN) { // CB or CBI
2669 fsg->data_dir = data_dir;
2670 fsg->data_size = fsg->data_size_from_cmnd;
2672 } else { // Bulk-only
2673 if (fsg->data_size < fsg->data_size_from_cmnd) {
2675 /* Host data size < Device data size is a phase error.
2676 * Carry out the command, but only transfer as much
2677 * as we are allowed. */
2678 fsg->data_size_from_cmnd = fsg->data_size;
2679 fsg->phase_error = 1;
2682 fsg->residue = fsg->usb_amount_left = fsg->data_size;
2684 /* Conflicting data directions is a phase error */
2685 if (fsg->data_dir != data_dir && fsg->data_size_from_cmnd > 0) {
2686 fsg->phase_error = 1;
2690 /* Verify the length of the command itself */
2691 if (cmnd_size != fsg->cmnd_size) {
2693 /* Special case workaround: MS-Windows issues REQUEST SENSE
2694 * with cbw->Length == 12 (it should be 6). */
2695 if (fsg->cmnd[0] == SC_REQUEST_SENSE && fsg->cmnd_size == 12)
2696 cmnd_size = fsg->cmnd_size;
2698 fsg->phase_error = 1;
2703 /* Check that the LUN values are consistent */
2704 if (transport_is_bbb()) {
2705 if (fsg->lun != lun)
2706 DBG(fsg, "using LUN %d from CBW, "
2707 "not LUN %d from CDB\n",
2710 fsg->lun = lun; // Use LUN from the command
2713 if (fsg->lun >= 0 && fsg->lun < fsg->nluns) {
2714 fsg->curlun = curlun = &fsg->luns[fsg->lun];
2715 if (fsg->cmnd[0] != SC_REQUEST_SENSE) {
2716 curlun->sense_data = SS_NO_SENSE;
2717 curlun->sense_data_info = 0;
2718 curlun->info_valid = 0;
2721 fsg->curlun = curlun = NULL;
2722 fsg->bad_lun_okay = 0;
2724 /* INQUIRY and REQUEST SENSE commands are explicitly allowed
2725 * to use unsupported LUNs; all others may not. */
2726 if (fsg->cmnd[0] != SC_INQUIRY &&
2727 fsg->cmnd[0] != SC_REQUEST_SENSE) {
2728 DBG(fsg, "unsupported LUN %d\n", fsg->lun);
2733 /* If a unit attention condition exists, only INQUIRY and
2734 * REQUEST SENSE commands are allowed; anything else must fail. */
2735 if (curlun && curlun->unit_attention_data != SS_NO_SENSE &&
2736 fsg->cmnd[0] != SC_INQUIRY &&
2737 fsg->cmnd[0] != SC_REQUEST_SENSE) {
2738 curlun->sense_data = curlun->unit_attention_data;
2739 curlun->unit_attention_data = SS_NO_SENSE;
2743 /* Check that only command bytes listed in the mask are non-zero */
2744 fsg->cmnd[1] &= 0x1f; // Mask away the LUN
2745 for (i = 1; i < cmnd_size; ++i) {
2746 if (fsg->cmnd[i] && !(mask & (1 << i))) {
2748 curlun->sense_data = SS_INVALID_FIELD_IN_CDB;
2753 /* If the medium isn't mounted and the command needs to access
2754 * it, return an error. */
2755 if (curlun && !backing_file_is_open(curlun) && needs_medium) {
2756 curlun->sense_data = SS_MEDIUM_NOT_PRESENT;
2764 static int do_scsi_command(struct fsg_dev *fsg)
2766 struct fsg_buffhd *bh;
2768 int reply = -EINVAL;
2770 static char unknown[16];
2774 /* Wait for the next buffer to become available for data or status */
2775 bh = fsg->next_buffhd_to_drain = fsg->next_buffhd_to_fill;
2776 while (bh->state != BUF_STATE_EMPTY) {
2777 if ((rc = sleep_thread(fsg)) != 0)
2780 fsg->phase_error = 0;
2781 fsg->short_packet_received = 0;
2783 down_read(&fsg->filesem); // We're using the backing file
2784 switch (fsg->cmnd[0]) {
2787 fsg->data_size_from_cmnd = fsg->cmnd[4];
2788 if ((reply = check_command(fsg, 6, DATA_DIR_TO_HOST,
2791 reply = do_inquiry(fsg, bh);
2794 case SC_MODE_SELECT_6:
2795 fsg->data_size_from_cmnd = fsg->cmnd[4];
2796 if ((reply = check_command(fsg, 6, DATA_DIR_FROM_HOST,
2798 "MODE SELECT(6)")) == 0)
2799 reply = do_mode_select(fsg, bh);
2802 case SC_MODE_SELECT_10:
2803 fsg->data_size_from_cmnd = get_be16(&fsg->cmnd[7]);
2804 if ((reply = check_command(fsg, 10, DATA_DIR_FROM_HOST,
2806 "MODE SELECT(10)")) == 0)
2807 reply = do_mode_select(fsg, bh);
2810 case SC_MODE_SENSE_6:
2811 fsg->data_size_from_cmnd = fsg->cmnd[4];
2812 if ((reply = check_command(fsg, 6, DATA_DIR_TO_HOST,
2813 (1<<1) | (1<<2) | (1<<4), 0,
2814 "MODE SENSE(6)")) == 0)
2815 reply = do_mode_sense(fsg, bh);
2818 case SC_MODE_SENSE_10:
2819 fsg->data_size_from_cmnd = get_be16(&fsg->cmnd[7]);
2820 if ((reply = check_command(fsg, 10, DATA_DIR_TO_HOST,
2821 (1<<1) | (1<<2) | (3<<7), 0,
2822 "MODE SENSE(10)")) == 0)
2823 reply = do_mode_sense(fsg, bh);
2826 case SC_PREVENT_ALLOW_MEDIUM_REMOVAL:
2827 fsg->data_size_from_cmnd = 0;
2828 if ((reply = check_command(fsg, 6, DATA_DIR_NONE,
2830 "PREVENT-ALLOW MEDIUM REMOVAL")) == 0)
2831 reply = do_prevent_allow(fsg);
2836 fsg->data_size_from_cmnd = (i == 0 ? 256 : i) << 9;
2837 if ((reply = check_command(fsg, 6, DATA_DIR_TO_HOST,
2840 reply = do_read(fsg);
2844 fsg->data_size_from_cmnd = get_be16(&fsg->cmnd[7]) << 9;
2845 if ((reply = check_command(fsg, 10, DATA_DIR_TO_HOST,
2846 (1<<1) | (0xf<<2) | (3<<7), 1,
2848 reply = do_read(fsg);
2852 fsg->data_size_from_cmnd = get_be32(&fsg->cmnd[6]) << 9;
2853 if ((reply = check_command(fsg, 12, DATA_DIR_TO_HOST,
2854 (1<<1) | (0xf<<2) | (0xf<<6), 1,
2856 reply = do_read(fsg);
2859 case SC_READ_CAPACITY:
2860 fsg->data_size_from_cmnd = 8;
2861 if ((reply = check_command(fsg, 10, DATA_DIR_TO_HOST,
2862 (0xf<<2) | (1<<8), 1,
2863 "READ CAPACITY")) == 0)
2864 reply = do_read_capacity(fsg, bh);
2867 case SC_READ_FORMAT_CAPACITIES:
2868 fsg->data_size_from_cmnd = get_be16(&fsg->cmnd[7]);
2869 if ((reply = check_command(fsg, 10, DATA_DIR_TO_HOST,
2871 "READ FORMAT CAPACITIES")) == 0)
2872 reply = do_read_format_capacities(fsg, bh);
2875 case SC_REQUEST_SENSE:
2876 fsg->data_size_from_cmnd = fsg->cmnd[4];
2877 if ((reply = check_command(fsg, 6, DATA_DIR_TO_HOST,
2879 "REQUEST SENSE")) == 0)
2880 reply = do_request_sense(fsg, bh);
2883 case SC_START_STOP_UNIT:
2884 fsg->data_size_from_cmnd = 0;
2885 if ((reply = check_command(fsg, 6, DATA_DIR_NONE,
2887 "START-STOP UNIT")) == 0)
2888 reply = do_start_stop(fsg);
2891 case SC_SYNCHRONIZE_CACHE:
2892 fsg->data_size_from_cmnd = 0;
2893 if ((reply = check_command(fsg, 10, DATA_DIR_NONE,
2894 (0xf<<2) | (3<<7), 1,
2895 "SYNCHRONIZE CACHE")) == 0)
2896 reply = do_synchronize_cache(fsg);
2899 case SC_TEST_UNIT_READY:
2900 fsg->data_size_from_cmnd = 0;
2901 reply = check_command(fsg, 6, DATA_DIR_NONE,
2906 /* Although optional, this command is used by MS-Windows. We
2907 * support a minimal version: BytChk must be 0. */
2909 fsg->data_size_from_cmnd = 0;
2910 if ((reply = check_command(fsg, 10, DATA_DIR_NONE,
2911 (1<<1) | (0xf<<2) | (3<<7), 1,
2913 reply = do_verify(fsg);
2918 fsg->data_size_from_cmnd = (i == 0 ? 256 : i) << 9;
2919 if ((reply = check_command(fsg, 6, DATA_DIR_FROM_HOST,
2922 reply = do_write(fsg);
2926 fsg->data_size_from_cmnd = get_be16(&fsg->cmnd[7]) << 9;
2927 if ((reply = check_command(fsg, 10, DATA_DIR_FROM_HOST,
2928 (1<<1) | (0xf<<2) | (3<<7), 1,
2930 reply = do_write(fsg);
2934 fsg->data_size_from_cmnd = get_be32(&fsg->cmnd[6]) << 9;
2935 if ((reply = check_command(fsg, 12, DATA_DIR_FROM_HOST,
2936 (1<<1) | (0xf<<2) | (0xf<<6), 1,
2938 reply = do_write(fsg);
2941 /* Some mandatory commands that we recognize but don't implement.
2942 * They don't mean much in this setting. It's left as an exercise
2943 * for anyone interested to implement RESERVE and RELEASE in terms
2944 * of Posix locks. */
2945 case SC_FORMAT_UNIT:
2948 case SC_SEND_DIAGNOSTIC:
2952 fsg->data_size_from_cmnd = 0;
2953 sprintf(unknown, "Unknown x%02x", fsg->cmnd[0]);
2954 if ((reply = check_command(fsg, fsg->cmnd_size,
2955 DATA_DIR_UNKNOWN, 0xff, 0, unknown)) == 0) {
2956 fsg->curlun->sense_data = SS_INVALID_COMMAND;
2961 up_read(&fsg->filesem);
2963 if (reply == -EINTR || signal_pending(current))
2966 /* Set up the single reply buffer for finish_reply() */
2967 if (reply == -EINVAL)
2968 reply = 0; // Error reply length
2969 if (reply >= 0 && fsg->data_dir == DATA_DIR_TO_HOST) {
2970 reply = min((u32) reply, fsg->data_size_from_cmnd);
2971 bh->inreq->length = reply;
2972 bh->state = BUF_STATE_FULL;
2973 fsg->residue -= reply;
2974 } // Otherwise it's already set
2980 /*-------------------------------------------------------------------------*/
2982 static int received_cbw(struct fsg_dev *fsg, struct fsg_buffhd *bh)
2984 struct usb_request *req = bh->outreq;
2985 struct bulk_cb_wrap *cbw = (struct bulk_cb_wrap *) req->buf;
2987 /* Was this a real packet? */
2991 /* Is the CBW valid? */
2992 if (req->actual != USB_BULK_CB_WRAP_LEN ||
2993 cbw->Signature != __constant_cpu_to_le32(
2995 DBG(fsg, "invalid CBW: len %u sig 0x%x\n",
2997 le32_to_cpu(cbw->Signature));
2999 /* The Bulk-only spec says we MUST stall the bulk pipes!
3000 * If we want to avoid stalls, set a flag so that we will
3001 * clear the endpoint halts at the next reset. */
3002 if (!mod_data.can_stall)
3003 set_bit(CLEAR_BULK_HALTS, &fsg->atomic_bitflags);
3004 fsg_set_halt(fsg, fsg->bulk_out);
3005 halt_bulk_in_endpoint(fsg);
3009 /* Is the CBW meaningful? */
3010 if (cbw->Lun >= MAX_LUNS || cbw->Flags & ~USB_BULK_IN_FLAG ||
3011 cbw->Length < 6 || cbw->Length > MAX_COMMAND_SIZE) {
3012 DBG(fsg, "non-meaningful CBW: lun = %u, flags = 0x%x, "
3014 cbw->Lun, cbw->Flags, cbw->Length);
3016 /* We can do anything we want here, so let's stall the
3017 * bulk pipes if we are allowed to. */
3018 if (mod_data.can_stall) {
3019 fsg_set_halt(fsg, fsg->bulk_out);
3020 halt_bulk_in_endpoint(fsg);
3025 /* Save the command for later */
3026 fsg->cmnd_size = cbw->Length;
3027 memcpy(fsg->cmnd, cbw->CDB, fsg->cmnd_size);
3028 if (cbw->Flags & USB_BULK_IN_FLAG)
3029 fsg->data_dir = DATA_DIR_TO_HOST;
3031 fsg->data_dir = DATA_DIR_FROM_HOST;
3032 fsg->data_size = le32_to_cpu(cbw->DataTransferLength);
3033 if (fsg->data_size == 0)
3034 fsg->data_dir = DATA_DIR_NONE;
3035 fsg->lun = cbw->Lun;
3036 fsg->tag = cbw->Tag;
3041 static int get_next_command(struct fsg_dev *fsg)
3043 struct fsg_buffhd *bh;
3046 if (transport_is_bbb()) {
3048 /* Wait for the next buffer to become available */
3049 bh = fsg->next_buffhd_to_fill;
3050 while (bh->state != BUF_STATE_EMPTY) {
3051 if ((rc = sleep_thread(fsg)) != 0)
3055 /* Queue a request to read a Bulk-only CBW */
3056 set_bulk_out_req_length(fsg, bh, USB_BULK_CB_WRAP_LEN);
3057 bh->outreq->short_not_ok = 1;
3058 start_transfer(fsg, fsg->bulk_out, bh->outreq,
3059 &bh->outreq_busy, &bh->state);
3061 /* We will drain the buffer in software, which means we
3062 * can reuse it for the next filling. No need to advance
3063 * next_buffhd_to_fill. */
3065 /* Wait for the CBW to arrive */
3066 while (bh->state != BUF_STATE_FULL) {
3067 if ((rc = sleep_thread(fsg)) != 0)
3071 rc = received_cbw(fsg, bh);
3072 bh->state = BUF_STATE_EMPTY;
3074 } else { // USB_PR_CB or USB_PR_CBI
3076 /* Wait for the next command to arrive */
3077 while (fsg->cbbuf_cmnd_size == 0) {
3078 if ((rc = sleep_thread(fsg)) != 0)
3082 /* Is the previous status interrupt request still busy?
3083 * The host is allowed to skip reading the status,
3084 * so we must cancel it. */
3085 if (fsg->intreq_busy)
3086 usb_ep_dequeue(fsg->intr_in, fsg->intreq);
3088 /* Copy the command and mark the buffer empty */
3089 fsg->data_dir = DATA_DIR_UNKNOWN;
3090 spin_lock_irq(&fsg->lock);
3091 fsg->cmnd_size = fsg->cbbuf_cmnd_size;
3092 memcpy(fsg->cmnd, fsg->cbbuf_cmnd, fsg->cmnd_size);
3093 fsg->cbbuf_cmnd_size = 0;
3094 spin_unlock_irq(&fsg->lock);
3100 /*-------------------------------------------------------------------------*/
3102 static int enable_endpoint(struct fsg_dev *fsg, struct usb_ep *ep,
3103 const struct usb_endpoint_descriptor *d)
3107 ep->driver_data = fsg;
3108 rc = usb_ep_enable(ep, d);
3110 ERROR(fsg, "can't enable %s, result %d\n", ep->name, rc);
3114 static int alloc_request(struct fsg_dev *fsg, struct usb_ep *ep,
3115 struct usb_request **preq)
3117 *preq = usb_ep_alloc_request(ep, GFP_ATOMIC);
3120 ERROR(fsg, "can't allocate request for %s\n", ep->name);
3125 * Reset interface setting and re-init endpoint state (toggle etc).
3126 * Call with altsetting < 0 to disable the interface. The only other
3127 * available altsetting is 0, which enables the interface.
3129 static int do_set_interface(struct fsg_dev *fsg, int altsetting)
3133 const struct usb_endpoint_descriptor *d;
3136 DBG(fsg, "reset interface\n");
3139 /* Deallocate the requests */
3140 for (i = 0; i < NUM_BUFFERS; ++i) {
3141 struct fsg_buffhd *bh = &fsg->buffhds[i];
3144 usb_ep_free_request(fsg->bulk_in, bh->inreq);
3148 usb_ep_free_request(fsg->bulk_out, bh->outreq);
3153 usb_ep_free_request(fsg->intr_in, fsg->intreq);
3157 /* Disable the endpoints */
3158 if (fsg->bulk_in_enabled) {
3159 usb_ep_disable(fsg->bulk_in);
3160 fsg->bulk_in_enabled = 0;
3162 if (fsg->bulk_out_enabled) {
3163 usb_ep_disable(fsg->bulk_out);
3164 fsg->bulk_out_enabled = 0;
3166 if (fsg->intr_in_enabled) {
3167 usb_ep_disable(fsg->intr_in);
3168 fsg->intr_in_enabled = 0;
3172 if (altsetting < 0 || rc != 0)
3175 DBG(fsg, "set interface %d\n", altsetting);
3177 /* Enable the endpoints */
3178 d = ep_desc(fsg->gadget, &fs_bulk_in_desc, &hs_bulk_in_desc);
3179 if ((rc = enable_endpoint(fsg, fsg->bulk_in, d)) != 0)
3181 fsg->bulk_in_enabled = 1;
3183 d = ep_desc(fsg->gadget, &fs_bulk_out_desc, &hs_bulk_out_desc);
3184 if ((rc = enable_endpoint(fsg, fsg->bulk_out, d)) != 0)
3186 fsg->bulk_out_enabled = 1;
3187 fsg->bulk_out_maxpacket = le16_to_cpu(d->wMaxPacketSize);
3189 if (transport_is_cbi()) {
3190 d = ep_desc(fsg->gadget, &fs_intr_in_desc, &hs_intr_in_desc);
3191 if ((rc = enable_endpoint(fsg, fsg->intr_in, d)) != 0)
3193 fsg->intr_in_enabled = 1;
3196 /* Allocate the requests */
3197 for (i = 0; i < NUM_BUFFERS; ++i) {
3198 struct fsg_buffhd *bh = &fsg->buffhds[i];
3200 if ((rc = alloc_request(fsg, fsg->bulk_in, &bh->inreq)) != 0)
3202 if ((rc = alloc_request(fsg, fsg->bulk_out, &bh->outreq)) != 0)
3204 bh->inreq->buf = bh->outreq->buf = bh->buf;
3205 bh->inreq->dma = bh->outreq->dma = bh->dma;
3206 bh->inreq->context = bh->outreq->context = bh;
3207 bh->inreq->complete = bulk_in_complete;
3208 bh->outreq->complete = bulk_out_complete;
3210 if (transport_is_cbi()) {
3211 if ((rc = alloc_request(fsg, fsg->intr_in, &fsg->intreq)) != 0)
3213 fsg->intreq->complete = intr_in_complete;
3217 for (i = 0; i < fsg->nluns; ++i)
3218 fsg->luns[i].unit_attention_data = SS_RESET_OCCURRED;
3224 * Change our operational configuration. This code must agree with the code
3225 * that returns config descriptors, and with interface altsetting code.
3227 * It's also responsible for power management interactions. Some
3228 * configurations might not work with our current power sources.
3229 * For now we just assume the gadget is always self-powered.
3231 static int do_set_config(struct fsg_dev *fsg, u8 new_config)
3235 /* Disable the single interface */
3236 if (fsg->config != 0) {
3237 DBG(fsg, "reset config\n");
3239 rc = do_set_interface(fsg, -1);
3242 /* Enable the interface */
3243 if (new_config != 0) {
3244 fsg->config = new_config;
3245 if ((rc = do_set_interface(fsg, 0)) != 0)
3246 fsg->config = 0; // Reset on errors
3250 switch (fsg->gadget->speed) {
3251 case USB_SPEED_LOW: speed = "low"; break;
3252 case USB_SPEED_FULL: speed = "full"; break;
3253 case USB_SPEED_HIGH: speed = "high"; break;
3254 default: speed = "?"; break;
3256 INFO(fsg, "%s speed config #%d\n", speed, fsg->config);
3263 /*-------------------------------------------------------------------------*/
3265 static void handle_exception(struct fsg_dev *fsg)
3271 struct fsg_buffhd *bh;
3272 enum fsg_state old_state;
3275 unsigned int exception_req_tag;
3278 /* Clear the existing signals. Anything but SIGUSR1 is converted
3279 * into a high-priority EXIT exception. */
3281 sig = dequeue_signal_lock(current, &fsg->thread_signal_mask,
3285 if (sig != SIGUSR1) {
3286 if (fsg->state < FSG_STATE_EXIT)
3287 DBG(fsg, "Main thread exiting on signal\n");
3288 raise_exception(fsg, FSG_STATE_EXIT);
3292 /* Cancel all the pending transfers */
3293 if (fsg->intreq_busy)
3294 usb_ep_dequeue(fsg->intr_in, fsg->intreq);
3295 for (i = 0; i < NUM_BUFFERS; ++i) {
3296 bh = &fsg->buffhds[i];
3298 usb_ep_dequeue(fsg->bulk_in, bh->inreq);
3299 if (bh->outreq_busy)
3300 usb_ep_dequeue(fsg->bulk_out, bh->outreq);
3303 /* Wait until everything is idle */
3305 num_active = fsg->intreq_busy;
3306 for (i = 0; i < NUM_BUFFERS; ++i) {
3307 bh = &fsg->buffhds[i];
3308 num_active += bh->inreq_busy + bh->outreq_busy;
3310 if (num_active == 0)
3312 if (sleep_thread(fsg))
3316 /* Clear out the controller's fifos */
3317 if (fsg->bulk_in_enabled)
3318 usb_ep_fifo_flush(fsg->bulk_in);
3319 if (fsg->bulk_out_enabled)
3320 usb_ep_fifo_flush(fsg->bulk_out);
3321 if (fsg->intr_in_enabled)
3322 usb_ep_fifo_flush(fsg->intr_in);
3324 /* Reset the I/O buffer states and pointers, the SCSI
3325 * state, and the exception. Then invoke the handler. */
3326 spin_lock_irq(&fsg->lock);
3328 for (i = 0; i < NUM_BUFFERS; ++i) {
3329 bh = &fsg->buffhds[i];
3330 bh->state = BUF_STATE_EMPTY;
3332 fsg->next_buffhd_to_fill = fsg->next_buffhd_to_drain =
3335 exception_req_tag = fsg->exception_req_tag;
3336 new_config = fsg->new_config;
3337 old_state = fsg->state;
3339 if (old_state == FSG_STATE_ABORT_BULK_OUT)
3340 fsg->state = FSG_STATE_STATUS_PHASE;
3342 for (i = 0; i < fsg->nluns; ++i) {
3343 curlun = &fsg->luns[i];
3344 curlun->prevent_medium_removal = 0;
3345 curlun->sense_data = curlun->unit_attention_data =
3347 curlun->sense_data_info = 0;
3348 curlun->info_valid = 0;
3350 fsg->state = FSG_STATE_IDLE;
3352 spin_unlock_irq(&fsg->lock);
3354 /* Carry out any extra actions required for the exception */
3355 switch (old_state) {
3359 case FSG_STATE_ABORT_BULK_OUT:
3361 spin_lock_irq(&fsg->lock);
3362 if (fsg->state == FSG_STATE_STATUS_PHASE)
3363 fsg->state = FSG_STATE_IDLE;
3364 spin_unlock_irq(&fsg->lock);
3367 case FSG_STATE_RESET:
3368 /* In case we were forced against our will to halt a
3369 * bulk endpoint, clear the halt now. (The SuperH UDC
3370 * requires this.) */
3371 if (test_and_clear_bit(CLEAR_BULK_HALTS,
3372 &fsg->atomic_bitflags)) {
3373 usb_ep_clear_halt(fsg->bulk_in);
3374 usb_ep_clear_halt(fsg->bulk_out);
3377 if (transport_is_bbb()) {
3378 if (fsg->ep0_req_tag == exception_req_tag)
3379 ep0_queue(fsg); // Complete the status stage
3381 } else if (transport_is_cbi())
3382 send_status(fsg); // Status by interrupt pipe
3384 /* Technically this should go here, but it would only be
3385 * a waste of time. Ditto for the INTERFACE_CHANGE and
3386 * CONFIG_CHANGE cases. */
3387 // for (i = 0; i < fsg->nluns; ++i)
3388 // fsg->luns[i].unit_attention_data = SS_RESET_OCCURRED;
3391 case FSG_STATE_INTERFACE_CHANGE:
3392 rc = do_set_interface(fsg, 0);
3393 if (fsg->ep0_req_tag != exception_req_tag)
3395 if (rc != 0) // STALL on errors
3396 fsg_set_halt(fsg, fsg->ep0);
3397 else // Complete the status stage
3401 case FSG_STATE_CONFIG_CHANGE:
3402 rc = do_set_config(fsg, new_config);
3403 if (fsg->ep0_req_tag != exception_req_tag)
3405 if (rc != 0) // STALL on errors
3406 fsg_set_halt(fsg, fsg->ep0);
3407 else // Complete the status stage
3411 case FSG_STATE_DISCONNECT:
3413 do_set_config(fsg, 0); // Unconfigured state
3416 case FSG_STATE_EXIT:
3417 case FSG_STATE_TERMINATED:
3418 do_set_config(fsg, 0); // Free resources
3419 spin_lock_irq(&fsg->lock);
3420 fsg->state = FSG_STATE_TERMINATED; // Stop the thread
3421 spin_unlock_irq(&fsg->lock);
3427 /*-------------------------------------------------------------------------*/
3429 static int fsg_main_thread(void *fsg_)
3431 struct fsg_dev *fsg = (struct fsg_dev *) fsg_;
3433 /* Allow the thread to be killed by a signal, but set the signal mask
3434 * to block everything but INT, TERM, KILL, and USR1. */
3435 siginitsetinv(&fsg->thread_signal_mask, sigmask(SIGINT) |
3436 sigmask(SIGTERM) | sigmask(SIGKILL) |
3438 sigprocmask(SIG_SETMASK, &fsg->thread_signal_mask, NULL);
3440 /* Arrange for userspace references to be interpreted as kernel
3441 * pointers. That way we can pass a kernel pointer to a routine
3442 * that expects a __user pointer and it will work okay. */
3446 while (fsg->state != FSG_STATE_TERMINATED) {
3447 if (exception_in_progress(fsg) || signal_pending(current)) {
3448 handle_exception(fsg);
3452 if (!fsg->running) {
3457 if (get_next_command(fsg))
3460 spin_lock_irq(&fsg->lock);
3461 if (!exception_in_progress(fsg))
3462 fsg->state = FSG_STATE_DATA_PHASE;
3463 spin_unlock_irq(&fsg->lock);
3465 if (do_scsi_command(fsg) || finish_reply(fsg))
3468 spin_lock_irq(&fsg->lock);
3469 if (!exception_in_progress(fsg))
3470 fsg->state = FSG_STATE_STATUS_PHASE;
3471 spin_unlock_irq(&fsg->lock);
3473 if (send_status(fsg))
3476 spin_lock_irq(&fsg->lock);
3477 if (!exception_in_progress(fsg))
3478 fsg->state = FSG_STATE_IDLE;
3479 spin_unlock_irq(&fsg->lock);
3482 spin_lock_irq(&fsg->lock);
3483 fsg->thread_task = NULL;
3484 spin_unlock_irq(&fsg->lock);
3486 /* In case we are exiting because of a signal, unregister the
3487 * gadget driver and close the backing file. */
3488 if (test_and_clear_bit(REGISTERED, &fsg->atomic_bitflags)) {
3489 usb_gadget_unregister_driver(&fsg_driver);
3490 close_all_backing_files(fsg);
3493 /* Let the unbind and cleanup routines know the thread has exited */
3494 complete_and_exit(&fsg->thread_notifier, 0);
3498 /*-------------------------------------------------------------------------*/
3500 /* If the next two routines are called while the gadget is registered,
3501 * the caller must own fsg->filesem for writing. */
3503 static int open_backing_file(struct lun *curlun, const char *filename)
3506 struct file *filp = NULL;
3508 struct inode *inode = NULL;
3512 /* R/W if we can, R/O if we must */
3515 filp = filp_open(filename, O_RDWR | O_LARGEFILE, 0);
3516 if (-EROFS == PTR_ERR(filp))
3520 filp = filp_open(filename, O_RDONLY | O_LARGEFILE, 0);
3522 LINFO(curlun, "unable to open backing file: %s\n", filename);
3523 return PTR_ERR(filp);
3526 if (!(filp->f_mode & FMODE_WRITE))
3530 inode = filp->f_dentry->d_inode;
3531 if (inode && S_ISBLK(inode->i_mode)) {
3532 if (bdev_read_only(inode->i_bdev))
3534 } else if (!inode || !S_ISREG(inode->i_mode)) {
3535 LINFO(curlun, "invalid file type: %s\n", filename);
3539 /* If we can't read the file, it's no good.
3540 * If we can't write the file, use it read-only. */
3541 if (!filp->f_op || !(filp->f_op->read || filp->f_op->aio_read)) {
3542 LINFO(curlun, "file not readable: %s\n", filename);
3545 if (!(filp->f_op->write || filp->f_op->aio_write))
3548 size = i_size_read(inode->i_mapping->host);
3550 LINFO(curlun, "unable to find file size: %s\n", filename);
3554 num_sectors = size >> 9; // File size in 512-byte sectors
3555 if (num_sectors == 0) {
3556 LINFO(curlun, "file too small: %s\n", filename);
3563 curlun->filp = filp;
3564 curlun->file_length = size;
3565 curlun->num_sectors = num_sectors;
3566 LDBG(curlun, "open backing file: %s\n", filename);
3570 filp_close(filp, current->files);
3575 static void close_backing_file(struct lun *curlun)
3578 LDBG(curlun, "close backing file\n");
3580 curlun->filp = NULL;
3584 static void close_all_backing_files(struct fsg_dev *fsg)
3588 for (i = 0; i < fsg->nluns; ++i)
3589 close_backing_file(&fsg->luns[i]);
3593 static ssize_t show_ro(struct device *dev, struct device_attribute *attr, char *buf)
3595 struct lun *curlun = dev_to_lun(dev);
3597 return sprintf(buf, "%d\n", curlun->ro);
3600 static ssize_t show_file(struct device *dev, struct device_attribute *attr, char *buf)
3602 struct lun *curlun = dev_to_lun(dev);
3603 struct fsg_dev *fsg = (struct fsg_dev *) dev_get_drvdata(dev);
3607 down_read(&fsg->filesem);
3608 if (backing_file_is_open(curlun)) { // Get the complete pathname
3609 p = d_path(curlun->filp->f_dentry, curlun->filp->f_vfsmnt,
3610 buf, PAGE_SIZE - 1);
3615 memmove(buf, p, rc);
3616 buf[rc] = '\n'; // Add a newline
3619 } else { // No file, return 0 bytes
3623 up_read(&fsg->filesem);
3628 static ssize_t store_ro(struct device *dev, struct device_attribute *attr, const char *buf, size_t count)
3631 struct lun *curlun = dev_to_lun(dev);
3632 struct fsg_dev *fsg = (struct fsg_dev *) dev_get_drvdata(dev);
3635 if (sscanf(buf, "%d", &i) != 1)
3638 /* Allow the write-enable status to change only while the backing file
3640 down_read(&fsg->filesem);
3641 if (backing_file_is_open(curlun)) {
3642 LDBG(curlun, "read-only status change prevented\n");
3646 LDBG(curlun, "read-only status set to %d\n", curlun->ro);
3648 up_read(&fsg->filesem);
3652 static ssize_t store_file(struct device *dev, struct device_attribute *attr, const char *buf, size_t count)
3654 struct lun *curlun = dev_to_lun(dev);
3655 struct fsg_dev *fsg = (struct fsg_dev *) dev_get_drvdata(dev);
3658 if (curlun->prevent_medium_removal && backing_file_is_open(curlun)) {
3659 LDBG(curlun, "eject attempt prevented\n");
3660 return -EBUSY; // "Door is locked"
3663 /* Remove a trailing newline */
3664 if (count > 0 && buf[count-1] == '\n')
3665 ((char *) buf)[count-1] = 0; // Ugh!
3667 /* Eject current medium */
3668 down_write(&fsg->filesem);
3669 if (backing_file_is_open(curlun)) {
3670 close_backing_file(curlun);
3671 curlun->unit_attention_data = SS_MEDIUM_NOT_PRESENT;
3674 /* Load new medium */
3675 if (count > 0 && buf[0]) {
3676 rc = open_backing_file(curlun, buf);
3678 curlun->unit_attention_data =
3679 SS_NOT_READY_TO_READY_TRANSITION;
3681 up_write(&fsg->filesem);
3682 return (rc < 0 ? rc : count);
3686 /* The write permissions and store_xxx pointers are set in fsg_bind() */
3687 static DEVICE_ATTR(ro, 0444, show_ro, NULL);
3688 static DEVICE_ATTR(file, 0444, show_file, NULL);
3691 /*-------------------------------------------------------------------------*/
3693 static void fsg_release(struct kref *ref)
3695 struct fsg_dev *fsg = container_of(ref, struct fsg_dev, ref);
3701 static void lun_release(struct device *dev)
3703 struct fsg_dev *fsg = (struct fsg_dev *) dev_get_drvdata(dev);
3705 kref_put(&fsg->ref, fsg_release);
3708 static void /* __init_or_exit */ fsg_unbind(struct usb_gadget *gadget)
3710 struct fsg_dev *fsg = get_gadget_data(gadget);
3713 struct usb_request *req = fsg->ep0req;
3715 DBG(fsg, "unbind\n");
3716 clear_bit(REGISTERED, &fsg->atomic_bitflags);
3718 /* Unregister the sysfs attribute files and the LUNs */
3719 for (i = 0; i < fsg->nluns; ++i) {
3720 curlun = &fsg->luns[i];
3721 if (curlun->registered) {
3722 device_remove_file(&curlun->dev, &dev_attr_ro);
3723 device_remove_file(&curlun->dev, &dev_attr_file);
3724 device_unregister(&curlun->dev);
3725 curlun->registered = 0;
3729 /* If the thread isn't already dead, tell it to exit now */
3730 if (fsg->state != FSG_STATE_TERMINATED) {
3731 raise_exception(fsg, FSG_STATE_EXIT);
3732 wait_for_completion(&fsg->thread_notifier);
3734 /* The cleanup routine waits for this completion also */
3735 complete(&fsg->thread_notifier);
3738 /* Free the data buffers */
3739 for (i = 0; i < NUM_BUFFERS; ++i) {
3740 struct fsg_buffhd *bh = &fsg->buffhds[i];
3743 usb_ep_free_buffer(fsg->bulk_in, bh->buf, bh->dma,
3747 /* Free the request and buffer for endpoint 0 */
3750 usb_ep_free_buffer(fsg->ep0, req->buf,
3751 req->dma, EP0_BUFSIZE);
3752 usb_ep_free_request(fsg->ep0, req);
3755 set_gadget_data(gadget, NULL);
3759 static int __init check_parameters(struct fsg_dev *fsg)
3764 /* Store the default values */
3765 mod_data.transport_type = USB_PR_BULK;
3766 mod_data.transport_name = "Bulk-only";
3767 mod_data.protocol_type = USB_SC_SCSI;
3768 mod_data.protocol_name = "Transparent SCSI";
3770 if (gadget_is_sh(fsg->gadget))
3771 mod_data.can_stall = 0;
3773 if (mod_data.release == 0xffff) { // Parameter wasn't set
3774 /* The sa1100 controller is not supported */
3775 if (gadget_is_sa1100(fsg->gadget))
3778 gcnum = usb_gadget_controller_number(fsg->gadget);
3780 mod_data.release = 0x0300 + gcnum;
3782 WARN(fsg, "controller '%s' not recognized\n",
3784 mod_data.release = 0x0399;
3788 prot = simple_strtol(mod_data.protocol_parm, NULL, 0);
3790 #ifdef CONFIG_USB_FILE_STORAGE_TEST
3791 if (strnicmp(mod_data.transport_parm, "BBB", 10) == 0) {
3792 ; // Use default setting
3793 } else if (strnicmp(mod_data.transport_parm, "CB", 10) == 0) {
3794 mod_data.transport_type = USB_PR_CB;
3795 mod_data.transport_name = "Control-Bulk";
3796 } else if (strnicmp(mod_data.transport_parm, "CBI", 10) == 0) {
3797 mod_data.transport_type = USB_PR_CBI;
3798 mod_data.transport_name = "Control-Bulk-Interrupt";
3800 ERROR(fsg, "invalid transport: %s\n", mod_data.transport_parm);
3804 if (strnicmp(mod_data.protocol_parm, "SCSI", 10) == 0 ||
3805 prot == USB_SC_SCSI) {
3806 ; // Use default setting
3807 } else if (strnicmp(mod_data.protocol_parm, "RBC", 10) == 0 ||
3808 prot == USB_SC_RBC) {
3809 mod_data.protocol_type = USB_SC_RBC;
3810 mod_data.protocol_name = "RBC";
3811 } else if (strnicmp(mod_data.protocol_parm, "8020", 4) == 0 ||
3812 strnicmp(mod_data.protocol_parm, "ATAPI", 10) == 0 ||
3813 prot == USB_SC_8020) {
3814 mod_data.protocol_type = USB_SC_8020;
3815 mod_data.protocol_name = "8020i (ATAPI)";
3816 } else if (strnicmp(mod_data.protocol_parm, "QIC", 3) == 0 ||
3817 prot == USB_SC_QIC) {
3818 mod_data.protocol_type = USB_SC_QIC;
3819 mod_data.protocol_name = "QIC-157";
3820 } else if (strnicmp(mod_data.protocol_parm, "UFI", 10) == 0 ||
3821 prot == USB_SC_UFI) {
3822 mod_data.protocol_type = USB_SC_UFI;
3823 mod_data.protocol_name = "UFI";
3824 } else if (strnicmp(mod_data.protocol_parm, "8070", 4) == 0 ||
3825 prot == USB_SC_8070) {
3826 mod_data.protocol_type = USB_SC_8070;
3827 mod_data.protocol_name = "8070i";
3829 ERROR(fsg, "invalid protocol: %s\n", mod_data.protocol_parm);
3833 mod_data.buflen &= PAGE_CACHE_MASK;
3834 if (mod_data.buflen <= 0) {
3835 ERROR(fsg, "invalid buflen\n");
3838 #endif /* CONFIG_USB_FILE_STORAGE_TEST */
3844 static int __init fsg_bind(struct usb_gadget *gadget)
3846 struct fsg_dev *fsg = the_fsg;
3851 struct usb_request *req;
3854 fsg->gadget = gadget;
3855 set_gadget_data(gadget, fsg);
3856 fsg->ep0 = gadget->ep0;
3857 fsg->ep0->driver_data = fsg;
3859 if ((rc = check_parameters(fsg)) != 0)
3862 if (mod_data.removable) { // Enable the store_xxx attributes
3863 dev_attr_ro.attr.mode = dev_attr_file.attr.mode = 0644;
3864 dev_attr_ro.store = store_ro;
3865 dev_attr_file.store = store_file;
3868 /* Find out how many LUNs there should be */
3871 i = max(mod_data.num_filenames, 1);
3873 ERROR(fsg, "invalid number of LUNs: %d\n", i);
3878 /* Create the LUNs, open their backing files, and register the
3879 * LUN devices in sysfs. */
3880 fsg->luns = kzalloc(i * sizeof(struct lun), GFP_KERNEL);
3887 for (i = 0; i < fsg->nluns; ++i) {
3888 curlun = &fsg->luns[i];
3889 curlun->ro = mod_data.ro[i];
3890 curlun->dev.release = lun_release;
3891 curlun->dev.parent = &gadget->dev;
3892 curlun->dev.driver = &fsg_driver.driver;
3893 dev_set_drvdata(&curlun->dev, fsg);
3894 snprintf(curlun->dev.bus_id, BUS_ID_SIZE,
3895 "%s-lun%d", gadget->dev.bus_id, i);
3897 if ((rc = device_register(&curlun->dev)) != 0) {
3898 INFO(fsg, "failed to register LUN%d: %d\n", i, rc);
3901 if ((rc = device_create_file(&curlun->dev,
3902 &dev_attr_ro)) != 0 ||
3903 (rc = device_create_file(&curlun->dev,
3904 &dev_attr_file)) != 0) {
3905 device_unregister(&curlun->dev);
3908 curlun->registered = 1;
3909 kref_get(&fsg->ref);
3911 if (mod_data.file[i] && *mod_data.file[i]) {
3912 if ((rc = open_backing_file(curlun,
3913 mod_data.file[i])) != 0)
3915 } else if (!mod_data.removable) {
3916 ERROR(fsg, "no file given for LUN%d\n", i);
3922 /* Find all the endpoints we will use */
3923 usb_ep_autoconfig_reset(gadget);
3924 ep = usb_ep_autoconfig(gadget, &fs_bulk_in_desc);
3927 ep->driver_data = fsg; // claim the endpoint
3930 ep = usb_ep_autoconfig(gadget, &fs_bulk_out_desc);
3933 ep->driver_data = fsg; // claim the endpoint
3936 if (transport_is_cbi()) {
3937 ep = usb_ep_autoconfig(gadget, &fs_intr_in_desc);
3940 ep->driver_data = fsg; // claim the endpoint
3944 /* Fix up the descriptors */
3945 device_desc.bMaxPacketSize0 = fsg->ep0->maxpacket;
3946 device_desc.idVendor = cpu_to_le16(mod_data.vendor);
3947 device_desc.idProduct = cpu_to_le16(mod_data.product);
3948 device_desc.bcdDevice = cpu_to_le16(mod_data.release);
3950 i = (transport_is_cbi() ? 3 : 2); // Number of endpoints
3951 intf_desc.bNumEndpoints = i;
3952 intf_desc.bInterfaceSubClass = mod_data.protocol_type;
3953 intf_desc.bInterfaceProtocol = mod_data.transport_type;
3954 fs_function[i + FS_FUNCTION_PRE_EP_ENTRIES] = NULL;
3956 #ifdef CONFIG_USB_GADGET_DUALSPEED
3957 hs_function[i + HS_FUNCTION_PRE_EP_ENTRIES] = NULL;
3959 /* Assume ep0 uses the same maxpacket value for both speeds */
3960 dev_qualifier.bMaxPacketSize0 = fsg->ep0->maxpacket;
3962 /* Assume that all endpoint addresses are the same for both speeds */
3963 hs_bulk_in_desc.bEndpointAddress = fs_bulk_in_desc.bEndpointAddress;
3964 hs_bulk_out_desc.bEndpointAddress = fs_bulk_out_desc.bEndpointAddress;
3965 hs_intr_in_desc.bEndpointAddress = fs_intr_in_desc.bEndpointAddress;
3968 if (gadget->is_otg) {
3969 otg_desc.bmAttributes |= USB_OTG_HNP,
3970 config_desc.bmAttributes |= USB_CONFIG_ATT_WAKEUP;
3975 /* Allocate the request and buffer for endpoint 0 */
3976 fsg->ep0req = req = usb_ep_alloc_request(fsg->ep0, GFP_KERNEL);
3979 req->buf = usb_ep_alloc_buffer(fsg->ep0, EP0_BUFSIZE,
3980 &req->dma, GFP_KERNEL);
3983 req->complete = ep0_complete;
3985 /* Allocate the data buffers */
3986 for (i = 0; i < NUM_BUFFERS; ++i) {
3987 struct fsg_buffhd *bh = &fsg->buffhds[i];
3989 /* Allocate for the bulk-in endpoint. We assume that
3990 * the buffer will also work with the bulk-out (and
3991 * interrupt-in) endpoint. */
3992 bh->buf = usb_ep_alloc_buffer(fsg->bulk_in, mod_data.buflen,
3993 &bh->dma, GFP_KERNEL);
3998 fsg->buffhds[NUM_BUFFERS - 1].next = &fsg->buffhds[0];
4000 /* This should reflect the actual gadget power source */
4001 usb_gadget_set_selfpowered(gadget);
4003 snprintf(manufacturer, sizeof manufacturer, "%s %s with %s",
4004 init_utsname()->sysname, init_utsname()->release,
4007 /* On a real device, serial[] would be loaded from permanent
4008 * storage. We just encode it from the driver version string. */
4009 for (i = 0; i < sizeof(serial) - 2; i += 2) {
4010 unsigned char c = DRIVER_VERSION[i / 2];
4014 sprintf(&serial[i], "%02X", c);
4017 fsg->thread_task = kthread_create(fsg_main_thread, fsg,
4018 "file-storage-gadget");
4019 if (IS_ERR(fsg->thread_task)) {
4020 rc = PTR_ERR(fsg->thread_task);
4024 INFO(fsg, DRIVER_DESC ", version: " DRIVER_VERSION "\n");
4025 INFO(fsg, "Number of LUNs=%d\n", fsg->nluns);
4027 pathbuf = kmalloc(PATH_MAX, GFP_KERNEL);
4028 for (i = 0; i < fsg->nluns; ++i) {
4029 curlun = &fsg->luns[i];
4030 if (backing_file_is_open(curlun)) {
4033 p = d_path(curlun->filp->f_dentry,
4034 curlun->filp->f_vfsmnt,
4039 LINFO(curlun, "ro=%d, file: %s\n",
4040 curlun->ro, (p ? p : "(error)"));
4045 DBG(fsg, "transport=%s (x%02x)\n",
4046 mod_data.transport_name, mod_data.transport_type);
4047 DBG(fsg, "protocol=%s (x%02x)\n",
4048 mod_data.protocol_name, mod_data.protocol_type);
4049 DBG(fsg, "VendorID=x%04x, ProductID=x%04x, Release=x%04x\n",
4050 mod_data.vendor, mod_data.product, mod_data.release);
4051 DBG(fsg, "removable=%d, stall=%d, buflen=%u\n",
4052 mod_data.removable, mod_data.can_stall,
4054 DBG(fsg, "I/O thread pid: %d\n", fsg->thread_task->pid);
4056 set_bit(REGISTERED, &fsg->atomic_bitflags);
4058 /* Tell the thread to start working */
4059 wake_up_process(fsg->thread_task);
4063 ERROR(fsg, "unable to autoconfigure all endpoints\n");
4067 fsg->state = FSG_STATE_TERMINATED; // The thread is dead
4069 close_all_backing_files(fsg);
4074 /*-------------------------------------------------------------------------*/
4076 static void fsg_suspend(struct usb_gadget *gadget)
4078 struct fsg_dev *fsg = get_gadget_data(gadget);
4080 DBG(fsg, "suspend\n");
4081 set_bit(SUSPENDED, &fsg->atomic_bitflags);
4084 static void fsg_resume(struct usb_gadget *gadget)
4086 struct fsg_dev *fsg = get_gadget_data(gadget);
4088 DBG(fsg, "resume\n");
4089 clear_bit(SUSPENDED, &fsg->atomic_bitflags);
4093 /*-------------------------------------------------------------------------*/
4095 static struct usb_gadget_driver fsg_driver = {
4096 #ifdef CONFIG_USB_GADGET_DUALSPEED
4097 .speed = USB_SPEED_HIGH,
4099 .speed = USB_SPEED_FULL,
4101 .function = (char *) longname,
4103 .unbind = __exit_p(fsg_unbind),
4104 .disconnect = fsg_disconnect,
4106 .suspend = fsg_suspend,
4107 .resume = fsg_resume,
4110 .name = (char *) shortname,
4111 .owner = THIS_MODULE,
4119 static int __init fsg_alloc(void)
4121 struct fsg_dev *fsg;
4123 fsg = kzalloc(sizeof *fsg, GFP_KERNEL);
4126 spin_lock_init(&fsg->lock);
4127 init_rwsem(&fsg->filesem);
4128 kref_init(&fsg->ref);
4129 init_completion(&fsg->thread_notifier);
4136 static int __init fsg_init(void)
4139 struct fsg_dev *fsg;
4141 if ((rc = fsg_alloc()) != 0)
4144 if ((rc = usb_gadget_register_driver(&fsg_driver)) != 0)
4145 kref_put(&fsg->ref, fsg_release);
4148 module_init(fsg_init);
4151 static void __exit fsg_cleanup(void)
4153 struct fsg_dev *fsg = the_fsg;
4155 /* Unregister the driver iff the thread hasn't already done so */
4156 if (test_and_clear_bit(REGISTERED, &fsg->atomic_bitflags))
4157 usb_gadget_unregister_driver(&fsg_driver);
4159 /* Wait for the thread to finish up */
4160 wait_for_completion(&fsg->thread_notifier);
4162 close_all_backing_files(fsg);
4163 kref_put(&fsg->ref, fsg_release);
4165 module_exit(fsg_cleanup);
projects / linux-2.6 / blob