git.oblomov.eu Git - linux-2.6/blob - arch/powerpc/platforms/powermac/smp.c

   1 /*
   2  * SMP support for power macintosh.
   3  *
   4  * We support both the old "powersurge" SMP architecture
   5  * and the current Core99 (G4 PowerMac) machines.
   6  *
   7  * Note that we don't support the very first rev. of
   8  * Apple/DayStar 2 CPUs board, the one with the funky
   9  * watchdog. Hopefully, none of these should be there except
  10  * maybe internally to Apple. I should probably still add some
  11  * code to detect this card though and disable SMP. --BenH.
  12  *
  13  * Support Macintosh G4 SMP by Troy Benjegerdes (hozer@drgw.net)
  14  * and Ben Herrenschmidt <benh@kernel.crashing.org>.
  15  *
  16  * Support for DayStar quad CPU cards
  17  * Copyright (C) XLR8, Inc. 1994-2000
  18  *
  19  *  This program is free software; you can redistribute it and/or
  20  *  modify it under the terms of the GNU General Public License
  21  *  as published by the Free Software Foundation; either version
  22  *  2 of the License, or (at your option) any later version.
  23  */
  24 #include <linux/kernel.h>
  25 #include <linux/sched.h>
  26 #include <linux/smp.h>
  27 #include <linux/interrupt.h>
  28 #include <linux/kernel_stat.h>
  29 #include <linux/delay.h>
  30 #include <linux/init.h>
  31 #include <linux/spinlock.h>
  32 #include <linux/errno.h>
  33 #include <linux/hardirq.h>
  34 #include <linux/cpu.h>
  35 #include <linux/compiler.h>
  36
  37 #include <asm/ptrace.h>
  38 #include <asm/atomic.h>
  39 #include <asm/code-patching.h>
  40 #include <asm/irq.h>
  41 #include <asm/page.h>
  42 #include <asm/pgtable.h>
  43 #include <asm/sections.h>
  44 #include <asm/io.h>
  45 #include <asm/prom.h>
  46 #include <asm/smp.h>
  47 #include <asm/machdep.h>
  48 #include <asm/pmac_feature.h>
  49 #include <asm/time.h>
  50 #include <asm/mpic.h>
  51 #include <asm/cacheflush.h>
  52 #include <asm/keylargo.h>
  53 #include <asm/pmac_low_i2c.h>
  54 #include <asm/pmac_pfunc.h>
  55
  56 #undef DEBUG
  57
  58 #ifdef DEBUG
  59 #define DBG(fmt...) udbg_printf(fmt)
  60 #else
  61 #define DBG(fmt...)
  62 #endif
  63
  64 extern void __secondary_start_pmac_0(void);
  65 extern int pmac_pfunc_base_install(void);
  66
  67 #ifdef CONFIG_PPC32
  68
  69 /* Sync flag for HW tb sync */
  70 static volatile int sec_tb_reset = 0;
  71
  72 /*
  73  * Powersurge (old powermac SMP) support.
  74  */
  75
  76 /* Addresses for powersurge registers */
  77 #define HAMMERHEAD_BASE         0xf8000000
  78 #define HHEAD_CONFIG            0x90
  79 #define HHEAD_SEC_INTR          0xc0
  80
  81 /* register for interrupting the primary processor on the powersurge */
  82 /* N.B. this is actually the ethernet ROM! */
  83 #define PSURGE_PRI_INTR         0xf3019000
  84
  85 /* register for storing the start address for the secondary processor */
  86 /* N.B. this is the PCI config space address register for the 1st bridge */
  87 #define PSURGE_START            0xf2800000
  88
  89 /* Daystar/XLR8 4-CPU card */
  90 #define PSURGE_QUAD_REG_ADDR    0xf8800000
  91
  92 #define PSURGE_QUAD_IRQ_SET     0
  93 #define PSURGE_QUAD_IRQ_CLR     1
  94 #define PSURGE_QUAD_IRQ_PRIMARY 2
  95 #define PSURGE_QUAD_CKSTOP_CTL  3
  96 #define PSURGE_QUAD_PRIMARY_ARB 4
  97 #define PSURGE_QUAD_BOARD_ID    6
  98 #define PSURGE_QUAD_WHICH_CPU   7
  99 #define PSURGE_QUAD_CKSTOP_RDBK 8
 100 #define PSURGE_QUAD_RESET_CTL   11
 101
 102 #define PSURGE_QUAD_OUT(r, v)   (out_8(quad_base + ((r) << 4) + 4, (v)))
 103 #define PSURGE_QUAD_IN(r)       (in_8(quad_base + ((r) << 4) + 4) & 0x0f)
 104 #define PSURGE_QUAD_BIS(r, v)   (PSURGE_QUAD_OUT((r), PSURGE_QUAD_IN(r) | (v)))
 105 #define PSURGE_QUAD_BIC(r, v)   (PSURGE_QUAD_OUT((r), PSURGE_QUAD_IN(r) & ~(v)))
 106
 107 /* virtual addresses for the above */
 108 static volatile u8 __iomem *hhead_base;
 109 static volatile u8 __iomem *quad_base;
 110 static volatile u32 __iomem *psurge_pri_intr;
 111 static volatile u8 __iomem *psurge_sec_intr;
 112 static volatile u32 __iomem *psurge_start;
 113
 114 /* values for psurge_type */
 115 #define PSURGE_NONE             -1
 116 #define PSURGE_DUAL             0
 117 #define PSURGE_QUAD_OKEE        1
 118 #define PSURGE_QUAD_COTTON      2
 119 #define PSURGE_QUAD_ICEGRASS    3
 120
 121 /* what sort of powersurge board we have */
 122 static int psurge_type = PSURGE_NONE;
 123
 124 /*
 125  * Set and clear IPIs for powersurge.
 126  */
 127 static inline void psurge_set_ipi(int cpu)
 128 {
 129         if (psurge_type == PSURGE_NONE)
 130                 return;
 131         if (cpu == 0)
 132                 in_be32(psurge_pri_intr);
 133         else if (psurge_type == PSURGE_DUAL)
 134                 out_8(psurge_sec_intr, 0);
 135         else
 136                 PSURGE_QUAD_OUT(PSURGE_QUAD_IRQ_SET, 1 << cpu);
 137 }
 138
 139 static inline void psurge_clr_ipi(int cpu)
 140 {
 141         if (cpu > 0) {
 142                 switch(psurge_type) {
 143                 case PSURGE_DUAL:
 144                         out_8(psurge_sec_intr, ~0);
 145                 case PSURGE_NONE:
 146                         break;
 147                 default:
 148                         PSURGE_QUAD_OUT(PSURGE_QUAD_IRQ_CLR, 1 << cpu);
 149                 }
 150         }
 151 }
 152
 153 /*
 154  * On powersurge (old SMP powermac architecture) we don't have
 155  * separate IPIs for separate messages like openpic does.  Instead
 156  * we have a bitmap for each processor, where a 1 bit means that
 157  * the corresponding message is pending for that processor.
 158  * Ideally each cpu's entry would be in a different cache line.
 159  *  -- paulus.
 160  */
 161 static unsigned long psurge_smp_message[NR_CPUS];
 162
 163 void psurge_smp_message_recv(void)
 164 {
 165         int cpu = smp_processor_id();
 166         int msg;
 167
 168         /* clear interrupt */
 169         psurge_clr_ipi(cpu);
 170
 171         if (num_online_cpus() < 2)
 172                 return;
 173
 174         /* make sure there is a message there */
 175         for (msg = 0; msg < 4; msg++)
 176                 if (test_and_clear_bit(msg, &psurge_smp_message[cpu]))
 177                         smp_message_recv(msg);
 178 }
 179
 180 irqreturn_t psurge_primary_intr(int irq, void *d)
 181 {
 182         psurge_smp_message_recv();
 183         return IRQ_HANDLED;
 184 }
 185
 186 static void smp_psurge_message_pass(int target, int msg)
 187 {
 188         int i;
 189
 190         if (num_online_cpus() < 2)
 191                 return;
 192
 193         for_each_online_cpu(i) {
 194                 if (target == MSG_ALL
 195                     || (target == MSG_ALL_BUT_SELF && i != smp_processor_id())
 196                     || target == i) {
 197                         set_bit(msg, &psurge_smp_message[i]);
 198                         psurge_set_ipi(i);
 199                 }
 200         }
 201 }
 202
 203 /*
 204  * Determine a quad card presence. We read the board ID register, we
 205  * force the data bus to change to something else, and we read it again.
 206  * It it's stable, then the register probably exist (ugh !)
 207  */
 208 static int __init psurge_quad_probe(void)
 209 {
 210         int type;
 211         unsigned int i;
 212
 213         type = PSURGE_QUAD_IN(PSURGE_QUAD_BOARD_ID);
 214         if (type < PSURGE_QUAD_OKEE || type > PSURGE_QUAD_ICEGRASS
 215             || type != PSURGE_QUAD_IN(PSURGE_QUAD_BOARD_ID))
 216                 return PSURGE_DUAL;
 217
 218         /* looks OK, try a slightly more rigorous test */
 219         /* bogus is not necessarily cacheline-aligned,
 220            though I don't suppose that really matters.  -- paulus */
 221         for (i = 0; i < 100; i++) {
 222                 volatile u32 bogus[8];
 223                 bogus[(0+i)%8] = 0x00000000;
 224                 bogus[(1+i)%8] = 0x55555555;
 225                 bogus[(2+i)%8] = 0xFFFFFFFF;
 226                 bogus[(3+i)%8] = 0xAAAAAAAA;
 227                 bogus[(4+i)%8] = 0x33333333;
 228                 bogus[(5+i)%8] = 0xCCCCCCCC;
 229                 bogus[(6+i)%8] = 0xCCCCCCCC;
 230                 bogus[(7+i)%8] = 0x33333333;
 231                 wmb();
 232                 asm volatile("dcbf 0,%0" : : "r" (bogus) : "memory");
 233                 mb();
 234                 if (type != PSURGE_QUAD_IN(PSURGE_QUAD_BOARD_ID))
 235                         return PSURGE_DUAL;
 236         }
 237         return type;
 238 }
 239
 240 static void __init psurge_quad_init(void)
 241 {
 242         int procbits;
 243
 244         if (ppc_md.progress) ppc_md.progress("psurge_quad_init", 0x351);
 245         procbits = ~PSURGE_QUAD_IN(PSURGE_QUAD_WHICH_CPU);
 246         if (psurge_type == PSURGE_QUAD_ICEGRASS)
 247                 PSURGE_QUAD_BIS(PSURGE_QUAD_RESET_CTL, procbits);
 248         else
 249                 PSURGE_QUAD_BIC(PSURGE_QUAD_CKSTOP_CTL, procbits);
 250         mdelay(33);
 251         out_8(psurge_sec_intr, ~0);
 252         PSURGE_QUAD_OUT(PSURGE_QUAD_IRQ_CLR, procbits);
 253         PSURGE_QUAD_BIS(PSURGE_QUAD_RESET_CTL, procbits);
 254         if (psurge_type != PSURGE_QUAD_ICEGRASS)
 255                 PSURGE_QUAD_BIS(PSURGE_QUAD_CKSTOP_CTL, procbits);
 256         PSURGE_QUAD_BIC(PSURGE_QUAD_PRIMARY_ARB, procbits);
 257         mdelay(33);
 258         PSURGE_QUAD_BIC(PSURGE_QUAD_RESET_CTL, procbits);
 259         mdelay(33);
 260         PSURGE_QUAD_BIS(PSURGE_QUAD_PRIMARY_ARB, procbits);
 261         mdelay(33);
 262 }
 263
 264 static int __init smp_psurge_probe(void)
 265 {
 266         int i, ncpus;
 267         struct device_node *dn;
 268
 269         /* We don't do SMP on the PPC601 -- paulus */
 270         if (PVR_VER(mfspr(SPRN_PVR)) == 1)
 271                 return 1;
 272
 273         /*
 274          * The powersurge cpu board can be used in the generation
 275          * of powermacs that have a socket for an upgradeable cpu card,
 276          * including the 7500, 8500, 9500, 9600.
 277          * The device tree doesn't tell you if you have 2 cpus because
 278          * OF doesn't know anything about the 2nd processor.
 279          * Instead we look for magic bits in magic registers,
 280          * in the hammerhead memory controller in the case of the
 281          * dual-cpu powersurge board.  -- paulus.
 282          */
 283         dn = of_find_node_by_name(NULL, "hammerhead");
 284         if (dn == NULL)
 285                 return 1;
 286         of_node_put(dn);
 287
 288         hhead_base = ioremap(HAMMERHEAD_BASE, 0x800);
 289         quad_base = ioremap(PSURGE_QUAD_REG_ADDR, 1024);
 290         psurge_sec_intr = hhead_base + HHEAD_SEC_INTR;
 291
 292         psurge_type = psurge_quad_probe();
 293         if (psurge_type != PSURGE_DUAL) {
 294                 psurge_quad_init();
 295                 /* All released cards using this HW design have 4 CPUs */
 296                 ncpus = 4;
 297         } else {
 298                 iounmap(quad_base);
 299                 if ((in_8(hhead_base + HHEAD_CONFIG) & 0x02) == 0) {
 300                         /* not a dual-cpu card */
 301                         iounmap(hhead_base);
 302                         psurge_type = PSURGE_NONE;
 303                         return 1;
 304                 }
 305                 ncpus = 2;
 306         }
 307
 308         psurge_start = ioremap(PSURGE_START, 4);
 309         psurge_pri_intr = ioremap(PSURGE_PRI_INTR, 4);
 310
 311         /*
 312          * This is necessary because OF doesn't know about the
 313          * secondary cpu(s), and thus there aren't nodes in the
 314          * device tree for them, and smp_setup_cpu_maps hasn't
 315          * set their bits in cpu_possible_map and cpu_present_map.
 316          */
 317         if (ncpus > NR_CPUS)
 318                 ncpus = NR_CPUS;
 319         for (i = 1; i < ncpus ; ++i) {
 320                 cpu_set(i, cpu_present_map);
 321                 set_hard_smp_processor_id(i, i);
 322         }
 323
 324         if (ppc_md.progress) ppc_md.progress("smp_psurge_probe - done", 0x352);
 325
 326         return ncpus;
 327 }
 328
 329 static void __init smp_psurge_kick_cpu(int nr)
 330 {
 331         unsigned long start = __pa(__secondary_start_pmac_0) + nr * 8;
 332         unsigned long a;
 333         int i;
 334
 335         /* may need to flush here if secondary bats aren't setup */
 336         for (a = KERNELBASE; a < KERNELBASE + 0x800000; a += 32)
 337                 asm volatile("dcbf 0,%0" : : "r" (a) : "memory");
 338         asm volatile("sync");
 339
 340         if (ppc_md.progress) ppc_md.progress("smp_psurge_kick_cpu", 0x353);
 341
 342         out_be32(psurge_start, start);
 343         mb();
 344
 345         psurge_set_ipi(nr);
 346         /*
 347          * We can't use udelay here because the timebase is now frozen.
 348          */
 349         for (i = 0; i < 2000; ++i)
 350                 barrier();
 351         psurge_clr_ipi(nr);
 352
 353         if (ppc_md.progress) ppc_md.progress("smp_psurge_kick_cpu - done", 0x354);
 354 }
 355
 356 /*
 357  * With the dual-cpu powersurge board, the decrementers and timebases
 358  * of both cpus are frozen after the secondary cpu is started up,
 359  * until we give the secondary cpu another interrupt.  This routine
 360  * uses this to get the timebases synchronized.
 361  *  -- paulus.
 362  */
 363 static void __init psurge_dual_sync_tb(int cpu_nr)
 364 {
 365         int t;
 366
 367         set_dec(tb_ticks_per_jiffy);
 368         /* XXX fixme */
 369         set_tb(0, 0);
 370
 371         if (cpu_nr > 0) {
 372                 mb();
 373                 sec_tb_reset = 1;
 374                 return;
 375         }
 376
 377         /* wait for the secondary to have reset its TB before proceeding */
 378         for (t = 10000000; t > 0 && !sec_tb_reset; --t)
 379                 ;
 380
 381         /* now interrupt the secondary, starting both TBs */
 382         psurge_set_ipi(1);
 383 }
 384
 385 static struct irqaction psurge_irqaction = {
 386         .handler = psurge_primary_intr,
 387         .flags = IRQF_DISABLED,
 388         .name = "primary IPI",
 389 };
 390
 391 static void __init smp_psurge_setup_cpu(int cpu_nr)
 392 {
 393
 394         if (cpu_nr == 0) {
 395                 /* If we failed to start the second CPU, we should still
 396                  * send it an IPI to start the timebase & DEC or we might
 397                  * have them stuck.
 398                  */
 399                 if (num_online_cpus() < 2) {
 400                         if (psurge_type == PSURGE_DUAL)
 401                                 psurge_set_ipi(1);
 402                         return;
 403                 }
 404                 /* reset the entry point so if we get another intr we won't
 405                  * try to startup again */
 406                 out_be32(psurge_start, 0x100);
 407                 if (setup_irq(30, &psurge_irqaction))
 408                         printk(KERN_ERR "Couldn't get primary IPI interrupt");
 409         }
 410
 411         if (psurge_type == PSURGE_DUAL)
 412                 psurge_dual_sync_tb(cpu_nr);
 413 }
 414
 415 void __init smp_psurge_take_timebase(void)
 416 {
 417         /* Dummy implementation */
 418 }
 419
 420 void __init smp_psurge_give_timebase(void)
 421 {
 422         /* Dummy implementation */
 423 }
 424
 425 /* PowerSurge-style Macs */
 426 struct smp_ops_t psurge_smp_ops = {
 427         .message_pass   = smp_psurge_message_pass,
 428         .probe          = smp_psurge_probe,
 429         .kick_cpu       = smp_psurge_kick_cpu,
 430         .setup_cpu      = smp_psurge_setup_cpu,
 431         .give_timebase  = smp_psurge_give_timebase,
 432         .take_timebase  = smp_psurge_take_timebase,
 433 };
 434 #endif /* CONFIG_PPC32 - actually powersurge support */
 435
 436 /*
 437  * Core 99 and later support
 438  */
 439
 440 static void (*pmac_tb_freeze)(int freeze);
 441 static u64 timebase;
 442 static int tb_req;
 443
 444 static void smp_core99_give_timebase(void)
 445 {
 446         unsigned long flags;
 447
 448         local_irq_save(flags);
 449
 450         while(!tb_req)
 451                 barrier();
 452         tb_req = 0;
 453         (*pmac_tb_freeze)(1);
 454         mb();
 455         timebase = get_tb();
 456         mb();
 457         while (timebase)
 458                 barrier();
 459         mb();
 460         (*pmac_tb_freeze)(0);
 461         mb();
 462
 463         local_irq_restore(flags);
 464 }
 465
 466
 467 static void __devinit smp_core99_take_timebase(void)
 468 {
 469         unsigned long flags;
 470
 471         local_irq_save(flags);
 472
 473         tb_req = 1;
 474         mb();
 475         while (!timebase)
 476                 barrier();
 477         mb();
 478         set_tb(timebase >> 32, timebase & 0xffffffff);
 479         timebase = 0;
 480         mb();
 481         set_dec(tb_ticks_per_jiffy/2);
 482
 483         local_irq_restore(flags);
 484 }
 485
 486 #ifdef CONFIG_PPC64
 487 /*
 488  * G5s enable/disable the timebase via an i2c-connected clock chip.
 489  */
 490 static struct pmac_i2c_bus *pmac_tb_clock_chip_host;
 491 static u8 pmac_tb_pulsar_addr;
 492
 493 static void smp_core99_cypress_tb_freeze(int freeze)
 494 {
 495         u8 data;
 496         int rc;
 497
 498         /* Strangely, the device-tree says address is 0xd2, but darwin
 499          * accesses 0xd0 ...
 500          */
 501         pmac_i2c_setmode(pmac_tb_clock_chip_host,
 502                          pmac_i2c_mode_combined);
 503         rc = pmac_i2c_xfer(pmac_tb_clock_chip_host,
 504                            0xd0 | pmac_i2c_read,
 505                            1, 0x81, &data, 1);
 506         if (rc != 0)
 507                 goto bail;
 508
 509         data = (data & 0xf3) | (freeze ? 0x00 : 0x0c);
 510
 511         pmac_i2c_setmode(pmac_tb_clock_chip_host, pmac_i2c_mode_stdsub);
 512         rc = pmac_i2c_xfer(pmac_tb_clock_chip_host,
 513                            0xd0 | pmac_i2c_write,
 514                            1, 0x81, &data, 1);
 515
 516  bail:
 517         if (rc != 0) {
 518                 printk("Cypress Timebase %s rc: %d\n",
 519                        freeze ? "freeze" : "unfreeze", rc);
 520                 panic("Timebase freeze failed !\n");
 521         }
 522 }
 523
 524
 525 static void smp_core99_pulsar_tb_freeze(int freeze)
 526 {
 527         u8 data;
 528         int rc;
 529
 530         pmac_i2c_setmode(pmac_tb_clock_chip_host,
 531                          pmac_i2c_mode_combined);
 532         rc = pmac_i2c_xfer(pmac_tb_clock_chip_host,
 533                            pmac_tb_pulsar_addr | pmac_i2c_read,
 534                            1, 0x2e, &data, 1);
 535         if (rc != 0)
 536                 goto bail;
 537
 538         data = (data & 0x88) | (freeze ? 0x11 : 0x22);
 539
 540         pmac_i2c_setmode(pmac_tb_clock_chip_host, pmac_i2c_mode_stdsub);
 541         rc = pmac_i2c_xfer(pmac_tb_clock_chip_host,
 542                            pmac_tb_pulsar_addr | pmac_i2c_write,
 543                            1, 0x2e, &data, 1);
 544  bail:
 545         if (rc != 0) {
 546                 printk(KERN_ERR "Pulsar Timebase %s rc: %d\n",
 547                        freeze ? "freeze" : "unfreeze", rc);
 548                 panic("Timebase freeze failed !\n");
 549         }
 550 }
 551
 552 static void __init smp_core99_setup_i2c_hwsync(int ncpus)
 553 {
 554         struct device_node *cc = NULL;
 555         struct device_node *p;
 556         const char *name = NULL;
 557         const u32 *reg;
 558         int ok;
 559
 560         /* Look for the clock chip */
 561         while ((cc = of_find_node_by_name(cc, "i2c-hwclock")) != NULL) {
 562                 p = of_get_parent(cc);
 563                 ok = p && of_device_is_compatible(p, "uni-n-i2c");
 564                 of_node_put(p);
 565                 if (!ok)
 566                         continue;
 567
 568                 pmac_tb_clock_chip_host = pmac_i2c_find_bus(cc);
 569                 if (pmac_tb_clock_chip_host == NULL)
 570                         continue;
 571                 reg = of_get_property(cc, "reg", NULL);
 572                 if (reg == NULL)
 573                         continue;
 574                 switch (*reg) {
 575                 case 0xd2:
 576                         if (of_device_is_compatible(cc,"pulsar-legacy-slewing")) {
 577                                 pmac_tb_freeze = smp_core99_pulsar_tb_freeze;
 578                                 pmac_tb_pulsar_addr = 0xd2;
 579                                 name = "Pulsar";
 580                         } else if (of_device_is_compatible(cc, "cy28508")) {
 581                                 pmac_tb_freeze = smp_core99_cypress_tb_freeze;
 582                                 name = "Cypress";
 583                         }
 584                         break;
 585                 case 0xd4:
 586                         pmac_tb_freeze = smp_core99_pulsar_tb_freeze;
 587                         pmac_tb_pulsar_addr = 0xd4;
 588                         name = "Pulsar";
 589                         break;
 590                 }
 591                 if (pmac_tb_freeze != NULL)
 592                         break;
 593         }
 594         if (pmac_tb_freeze != NULL) {
 595                 /* Open i2c bus for synchronous access */
 596                 if (pmac_i2c_open(pmac_tb_clock_chip_host, 1)) {
 597                         printk(KERN_ERR "Failed top open i2c bus for clock"
 598                                " sync, fallback to software sync !\n");
 599                         goto no_i2c_sync;
 600                 }
 601                 printk(KERN_INFO "Processor timebase sync using %s i2c clock\n",
 602                        name);
 603                 return;
 604         }
 605  no_i2c_sync:
 606         pmac_tb_freeze = NULL;
 607         pmac_tb_clock_chip_host = NULL;
 608 }
 609
 610
 611
 612 /*
 613  * Newer G5s uses a platform function
 614  */
 615
 616 static void smp_core99_pfunc_tb_freeze(int freeze)
 617 {
 618         struct device_node *cpus;
 619         struct pmf_args args;
 620
 621         cpus = of_find_node_by_path("/cpus");
 622         BUG_ON(cpus == NULL);
 623         args.count = 1;
 624         args.u[0].v = !freeze;
 625         pmf_call_function(cpus, "cpu-timebase", &args);
 626         of_node_put(cpus);
 627 }
 628
 629 #else /* CONFIG_PPC64 */
 630
 631 /*
 632  * SMP G4 use a GPIO to enable/disable the timebase.
 633  */
 634
 635 static unsigned int core99_tb_gpio;     /* Timebase freeze GPIO */
 636
 637 static void smp_core99_gpio_tb_freeze(int freeze)
 638 {
 639         if (freeze)
 640                 pmac_call_feature(PMAC_FTR_WRITE_GPIO, NULL, core99_tb_gpio, 4);
 641         else
 642                 pmac_call_feature(PMAC_FTR_WRITE_GPIO, NULL, core99_tb_gpio, 0);
 643         pmac_call_feature(PMAC_FTR_READ_GPIO, NULL, core99_tb_gpio, 0);
 644 }
 645
 646
 647 #endif /* !CONFIG_PPC64 */
 648
 649 /* L2 and L3 cache settings to pass from CPU0 to CPU1 on G4 cpus */
 650 volatile static long int core99_l2_cache;
 651 volatile static long int core99_l3_cache;
 652
 653 static void __devinit core99_init_caches(int cpu)
 654 {
 655 #ifndef CONFIG_PPC64
 656         if (!cpu_has_feature(CPU_FTR_L2CR))
 657                 return;
 658
 659         if (cpu == 0) {
 660                 core99_l2_cache = _get_L2CR();
 661                 printk("CPU0: L2CR is %lx\n", core99_l2_cache);
 662         } else {
 663                 printk("CPU%d: L2CR was %lx\n", cpu, _get_L2CR());
 664                 _set_L2CR(0);
 665                 _set_L2CR(core99_l2_cache);
 666                 printk("CPU%d: L2CR set to %lx\n", cpu, core99_l2_cache);
 667         }
 668
 669         if (!cpu_has_feature(CPU_FTR_L3CR))
 670                 return;
 671
 672         if (cpu == 0){
 673                 core99_l3_cache = _get_L3CR();
 674                 printk("CPU0: L3CR is %lx\n", core99_l3_cache);
 675         } else {
 676                 printk("CPU%d: L3CR was %lx\n", cpu, _get_L3CR());
 677                 _set_L3CR(0);
 678                 _set_L3CR(core99_l3_cache);
 679                 printk("CPU%d: L3CR set to %lx\n", cpu, core99_l3_cache);
 680         }
 681 #endif /* !CONFIG_PPC64 */
 682 }
 683
 684 static void __init smp_core99_setup(int ncpus)
 685 {
 686 #ifdef CONFIG_PPC64
 687
 688         /* i2c based HW sync on some G5s */
 689         if (machine_is_compatible("PowerMac7,2") ||
 690             machine_is_compatible("PowerMac7,3") ||
 691             machine_is_compatible("RackMac3,1"))
 692                 smp_core99_setup_i2c_hwsync(ncpus);
 693
 694         /* pfunc based HW sync on recent G5s */
 695         if (pmac_tb_freeze == NULL) {
 696                 struct device_node *cpus =
 697                         of_find_node_by_path("/cpus");
 698                 if (cpus &&
 699                     of_get_property(cpus, "platform-cpu-timebase", NULL)) {
 700                         pmac_tb_freeze = smp_core99_pfunc_tb_freeze;
 701                         printk(KERN_INFO "Processor timebase sync using"
 702                                " platform function\n");
 703                 }
 704         }
 705
 706 #else /* CONFIG_PPC64 */
 707
 708         /* GPIO based HW sync on ppc32 Core99 */
 709         if (pmac_tb_freeze == NULL && !machine_is_compatible("MacRISC4")) {
 710                 struct device_node *cpu;
 711                 const u32 *tbprop = NULL;
 712
 713                 core99_tb_gpio = KL_GPIO_TB_ENABLE;     /* default value */
 714                 cpu = of_find_node_by_type(NULL, "cpu");
 715                 if (cpu != NULL) {
 716                         tbprop = of_get_property(cpu, "timebase-enable", NULL);
 717                         if (tbprop)
 718                                 core99_tb_gpio = *tbprop;
 719                         of_node_put(cpu);
 720                 }
 721                 pmac_tb_freeze = smp_core99_gpio_tb_freeze;
 722                 printk(KERN_INFO "Processor timebase sync using"
 723                        " GPIO 0x%02x\n", core99_tb_gpio);
 724         }
 725
 726 #endif /* CONFIG_PPC64 */
 727
 728         /* No timebase sync, fallback to software */
 729         if (pmac_tb_freeze == NULL) {
 730                 smp_ops->give_timebase = smp_generic_give_timebase;
 731                 smp_ops->take_timebase = smp_generic_take_timebase;
 732                 printk(KERN_INFO "Processor timebase sync using software\n");
 733         }
 734
 735 #ifndef CONFIG_PPC64
 736         {
 737                 int i;
 738
 739                 /* XXX should get this from reg properties */
 740                 for (i = 1; i < ncpus; ++i)
 741                         set_hard_smp_processor_id(i, i);
 742         }
 743 #endif
 744
 745         /* 32 bits SMP can't NAP */
 746         if (!machine_is_compatible("MacRISC4"))
 747                 powersave_nap = 0;
 748 }
 749
 750 static int __init smp_core99_probe(void)
 751 {
 752         struct device_node *cpus;
 753         int ncpus = 0;
 754
 755         if (ppc_md.progress) ppc_md.progress("smp_core99_probe", 0x345);
 756
 757         /* Count CPUs in the device-tree */
 758         for (cpus = NULL; (cpus = of_find_node_by_type(cpus, "cpu")) != NULL;)
 759                 ++ncpus;
 760
 761         printk(KERN_INFO "PowerMac SMP probe found %d cpus\n", ncpus);
 762
 763         /* Nothing more to do if less than 2 of them */
 764         if (ncpus <= 1)
 765                 return 1;
 766
 767         /* We need to perform some early initialisations before we can start
 768          * setting up SMP as we are running before initcalls
 769          */
 770         pmac_pfunc_base_install();
 771         pmac_i2c_init();
 772
 773         /* Setup various bits like timebase sync method, ability to nap, ... */
 774         smp_core99_setup(ncpus);
 775
 776         /* Install IPIs */
 777         mpic_request_ipis();
 778
 779         /* Collect l2cr and l3cr values from CPU 0 */
 780         core99_init_caches(0);
 781
 782         return ncpus;
 783 }
 784
 785 static void __devinit smp_core99_kick_cpu(int nr)
 786 {
 787         unsigned int save_vector;
 788         unsigned long target, flags;
 789         unsigned int *vector = (unsigned int *)(PAGE_OFFSET+0x100);
 790
 791         if (nr < 0 || nr > 3)
 792                 return;
 793
 794         if (ppc_md.progress)
 795                 ppc_md.progress("smp_core99_kick_cpu", 0x346);
 796
 797         local_irq_save(flags);
 798
 799         /* Save reset vector */
 800         save_vector = *vector;
 801
 802         /* Setup fake reset vector that does
 803          *   b __secondary_start_pmac_0 + nr*8
 804          */
 805         target = (unsigned long) __secondary_start_pmac_0 + nr * 8;
 806         patch_branch(vector, target, BRANCH_SET_LINK);
 807
 808         /* Put some life in our friend */
 809         pmac_call_feature(PMAC_FTR_RESET_CPU, NULL, nr, 0);
 810
 811         /* FIXME: We wait a bit for the CPU to take the exception, I should
 812          * instead wait for the entry code to set something for me. Well,
 813          * ideally, all that crap will be done in prom.c and the CPU left
 814          * in a RAM-based wait loop like CHRP.
 815          */
 816         mdelay(1);
 817
 818         /* Restore our exception vector */
 819         *vector = save_vector;
 820         flush_icache_range((unsigned long) vector, (unsigned long) vector + 4);
 821
 822         local_irq_restore(flags);
 823         if (ppc_md.progress) ppc_md.progress("smp_core99_kick_cpu done", 0x347);
 824 }
 825
 826 static void __devinit smp_core99_setup_cpu(int cpu_nr)
 827 {
 828         /* Setup L2/L3 */
 829         if (cpu_nr != 0)
 830                 core99_init_caches(cpu_nr);
 831
 832         /* Setup openpic */
 833         mpic_setup_this_cpu();
 834
 835         if (cpu_nr == 0) {
 836 #ifdef CONFIG_PPC64
 837                 extern void g5_phy_disable_cpu1(void);
 838
 839                 /* Close i2c bus if it was used for tb sync */
 840                 if (pmac_tb_clock_chip_host) {
 841                         pmac_i2c_close(pmac_tb_clock_chip_host);
 842                         pmac_tb_clock_chip_host = NULL;
 843                 }
 844
 845                 /* If we didn't start the second CPU, we must take
 846                  * it off the bus
 847                  */
 848                 if (machine_is_compatible("MacRISC4") &&
 849                     num_online_cpus() < 2)
 850                         g5_phy_disable_cpu1();
 851 #endif /* CONFIG_PPC64 */
 852
 853                 if (ppc_md.progress)
 854                         ppc_md.progress("core99_setup_cpu 0 done", 0x349);
 855         }
 856 }
 857
 858
 859 #if defined(CONFIG_HOTPLUG_CPU) && defined(CONFIG_PPC32)
 860
 861 int smp_core99_cpu_disable(void)
 862 {
 863         cpu_clear(smp_processor_id(), cpu_online_map);
 864
 865         /* XXX reset cpu affinity here */
 866         mpic_cpu_set_priority(0xf);
 867         asm volatile("mtdec %0" : : "r" (0x7fffffff));
 868         mb();
 869         udelay(20);
 870         asm volatile("mtdec %0" : : "r" (0x7fffffff));
 871         return 0;
 872 }
 873
 874 extern void low_cpu_die(void) __attribute__((noreturn)); /* in sleep.S */
 875 static int cpu_dead[NR_CPUS];
 876
 877 void cpu_die(void)
 878 {
 879         local_irq_disable();
 880         cpu_dead[smp_processor_id()] = 1;
 881         mb();
 882         low_cpu_die();
 883 }
 884
 885 void smp_core99_cpu_die(unsigned int cpu)
 886 {
 887         int timeout;
 888
 889         timeout = 1000;
 890         while (!cpu_dead[cpu]) {
 891                 if (--timeout == 0) {
 892                         printk("CPU %u refused to die!\n", cpu);
 893                         break;
 894                 }
 895                 msleep(1);
 896         }
 897         cpu_dead[cpu] = 0;
 898 }
 899
 900 #endif /* CONFIG_HOTPLUG_CPU && CONFIG_PP32 */
 901
 902 /* Core99 Macs (dual G4s and G5s) */
 903 struct smp_ops_t core99_smp_ops = {
 904         .message_pass   = smp_mpic_message_pass,
 905         .probe          = smp_core99_probe,
 906         .kick_cpu       = smp_core99_kick_cpu,
 907         .setup_cpu      = smp_core99_setup_cpu,
 908         .give_timebase  = smp_core99_give_timebase,
 909         .take_timebase  = smp_core99_take_timebase,
 910 #if defined(CONFIG_HOTPLUG_CPU)
 911 # if defined(CONFIG_PPC32)
 912         .cpu_disable    = smp_core99_cpu_disable,
 913         .cpu_die        = smp_core99_cpu_die,
 914 # endif
 915 # if defined(CONFIG_PPC64)
 916         .cpu_disable    = generic_cpu_disable,
 917         .cpu_die        = generic_cpu_die,
 918         /* intentionally do *NOT* assign cpu_enable,
 919          * the generic code will use kick_cpu then! */
 920 # endif
 921 #endif
 922 };