2 * net-3-driver for the NI5210 card (i82586 Ethernet chip)
4 * This is an extension to the Linux operating system, and is covered by the
5 * same GNU General Public License that covers that work.
7 * Alphacode 0.82 (96/09/29) for Linux 2.0.0 (or later)
8 * Copyrights (c) 1994,1995,1996 by M.Hipp (hippm@informatik.uni-tuebingen.de)
9 * [feel free to mail ....]
11 * when using as module: (no autoprobing!)
13 * gcc -O2 -fomit-frame-pointer -m486 -D__KERNEL__ -DMODULE -c ni52.c
15 * insmod ni52.o io=0x360 irq=9 memstart=0xd0000 memend=0xd4000
17 * CAN YOU PLEASE REPORT ME YOUR PERFORMANCE EXPERIENCES !!.
19 * If you find a bug, please report me:
20 * The kernel panic output and any kmsg from the ni52 driver
21 * the ni5210-driver-version and the linux-kernel version
22 * how many shared memory (memsize) on the netcard,
23 * bootprom: yes/no, base_addr, mem_start
24 * maybe the ni5210-card revision and the i82586 version
26 * autoprobe for: base_addr: 0x300,0x280,0x360,0x320,0x340
27 * mem_start: 0xd0000,0xd2000,0xc8000,0xca000,0xd4000,0xd6000,
28 * 0xd8000,0xcc000,0xce000,0xda000,0xdc000
31 * skeleton.c from Donald Becker
33 * I have also done a look in the following sources: (mail me if you need them)
34 * crynwr-packet-driver by Russ Nelson
35 * Garret A. Wollman's (fourth) i82586-driver for BSD
36 * (before getting an i82596 (yes 596 not 586) manual, the existing drivers helped
37 * me a lot to understand this tricky chip.)
40 * The internal sysbus seems to be slow. So we often lose packets because of
41 * overruns while receiving from a fast remote host.
42 * This can slow down TCP connections. Maybe the newer ni5210 cards are better.
43 * my experience is, that if a machine sends with more than about 500-600K/s
44 * the fifo/sysbus overflows.
47 * On fast networks, it's a (very) good idea to have 16K shared memory. With
48 * 8K, we can store only 4 receive frames, so it can (easily) happen that a remote
49 * machine 'overruns' our system.
51 * Known i82586/card problems (I'm sure, there are many more!):
52 * Running the NOP-mode, the i82586 sometimes seems to forget to report
53 * every xmit-interrupt until we restart the CU.
54 * Another MAJOR bug is, that the RU sometimes seems to ignore the EL-Bit
55 * in the RBD-Struct which indicates an end of the RBD queue.
56 * Instead, the RU fetches another (randomly selected and
57 * usually used) RBD and begins to fill it. (Maybe, this happens only if
58 * the last buffer from the previous RFD fits exact into the queue and
59 * the next RFD can't fetch an initial RBD. Anyone knows more? )
61 * results from ftp performance tests with Linux 1.2.5
62 * send and receive about 350-400 KByte/s (peak up to 460 kbytes/s)
63 * sending in NOP-mode: peak performance up to 530K/s (but better don't run this mode)
67 * 29.Sept.96: virt_to_bus changes for new memory scheme
68 * 19.Feb.96: more Mcast changes, module support (MH)
70 * 18.Nov.95: Mcast changes (AC).
72 * 23.April.95: fixed(?) receiving problems by configuring a RFD more
73 * than the number of RBD's. Can maybe cause other problems.
74 * 18.April.95: Added MODULE support (MH)
75 * 17.April.95: MC related changes in init586() and set_multicast_list().
76 * removed use of 'jiffies' in init586() (MH)
78 * 19.Sep.94: Added Multicast support (not tested yet) (MH)
80 * 18.Sep.94: Workaround for 'EL-Bug'. Removed flexible RBD-handling.
81 * Now, every RFD has exact one RBD. (MH)
83 * 14.Sep.94: added promiscuous mode, a few cleanups (MH)
85 * 19.Aug.94: changed request_irq() parameter (MH)
87 * 20.July.94: removed cleanup bugs, removed a 16K-mem-probe-bug (MH)
89 * 19.July.94: lotsa cleanups .. (MH)
91 * 17.July.94: some patches ... verified to run with 1.1.29 (MH)
93 * 4.July.94: patches for Linux 1.1.24 (MH)
95 * 26.March.94: patches for Linux 1.0 and iomem-auto-probe (MH)
97 * 30.Sep.93: Added nop-chain .. driver now runs with only one Xmit-Buff, too (MH)
99 * < 30.Sep.93: first versions
102 static int debuglevel; /* debug-printk 0: off 1: a few 2: more */
103 static int automatic_resume; /* experimental .. better should be zero */
104 static int rfdadd; /* rfdadd=1 may be better for 8K MEM cards */
105 static int fifo=0x8; /* don't change */
107 #include <linux/module.h>
108 #include <linux/kernel.h>
109 #include <linux/string.h>
110 #include <linux/errno.h>
111 #include <linux/ioport.h>
112 #include <linux/slab.h>
113 #include <linux/interrupt.h>
114 #include <linux/delay.h>
115 #include <linux/init.h>
116 #include <linux/bitops.h>
119 #include <linux/netdevice.h>
120 #include <linux/etherdevice.h>
121 #include <linux/skbuff.h>
125 #define DRV_NAME "ni52"
127 #define DEBUG /* debug on */
128 #define SYSBUSVAL 1 /* 8 Bit */
130 #define ni_attn586() {outb(0,dev->base_addr+NI52_ATTENTION);}
131 #define ni_reset586() {outb(0,dev->base_addr+NI52_RESET);}
132 #define ni_disint() {outb(0,dev->base_addr+NI52_INTDIS);}
133 #define ni_enaint() {outb(0,dev->base_addr+NI52_INTENA);}
135 #define make32(ptr16) (p->memtop + (short) (ptr16) )
136 #define make24(ptr32) ( ((char *) (ptr32)) - p->base)
137 #define make16(ptr32) ((unsigned short) ((unsigned long)(ptr32) - (unsigned long) p->memtop ))
139 /******************* how to calculate the buffers *****************************
141 * IMPORTANT NOTE: if you configure only one NUM_XMIT_BUFFS, the driver works
142 * --------------- in a different (more stable?) mode. Only in this mode it's
143 * possible to configure the driver with 'NO_NOPCOMMANDS'
145 sizeof(scp)=12; sizeof(scb)=16; sizeof(iscp)=8;
146 sizeof(scp)+sizeof(iscp)+sizeof(scb) = 36 = INIT
147 sizeof(rfd) = 24; sizeof(rbd) = 12;
148 sizeof(tbd) = 8; sizeof(transmit_cmd) = 16;
151 * if you don't know the driver, better do not change these values: */
153 #define RECV_BUFF_SIZE 1524 /* slightly oversized */
154 #define XMIT_BUFF_SIZE 1524 /* slightly oversized */
155 #define NUM_XMIT_BUFFS 1 /* config for both, 8K and 16K shmem */
156 #define NUM_RECV_BUFFS_8 4 /* config for 8K shared mem */
157 #define NUM_RECV_BUFFS_16 9 /* config for 16K shared mem */
158 #define NO_NOPCOMMANDS /* only possible with NUM_XMIT_BUFFS=1 */
160 /**************************************************************************/
162 /* different DELAYs */
163 #define DELAY(x) mdelay(32 * x);
164 #define DELAY_16(); { udelay(16); }
165 #define DELAY_18(); { udelay(4); }
167 /* wait for command with timeout: */
168 #define WAIT_4_SCB_CMD() \
170 for(i=0;i<16384;i++) { \
171 if(!p->scb->cmd_cuc) break; \
174 printk("%s: scb_cmd timed out: %04x,%04x .. disabling i82586!!\n",dev->name,p->scb->cmd_cuc,p->scb->cus); \
175 if(!p->reseted) { p->reseted = 1; ni_reset586(); } } } }
177 #define WAIT_4_SCB_CMD_RUC() { int i; \
178 for(i=0;i<16384;i++) { \
179 if(!p->scb->cmd_ruc) break; \
182 printk("%s: scb_cmd (ruc) timed out: %04x,%04x .. disabling i82586!!\n",dev->name,p->scb->cmd_ruc,p->scb->rus); \
183 if(!p->reseted) { p->reseted = 1; ni_reset586(); } } } }
185 #define WAIT_4_STAT_COMPL(addr) { int i; \
186 for(i=0;i<32767;i++) { \
187 if((addr)->cmd_status & STAT_COMPL) break; \
188 DELAY_16(); DELAY_16(); } }
190 #define NI52_TOTAL_SIZE 16
191 #define NI52_ADDR0 0x02
192 #define NI52_ADDR1 0x07
193 #define NI52_ADDR2 0x01
195 static int ni52_probe1(struct net_device *dev,int ioaddr);
196 static irqreturn_t ni52_interrupt(int irq,void *dev_id);
197 static int ni52_open(struct net_device *dev);
198 static int ni52_close(struct net_device *dev);
199 static int ni52_send_packet(struct sk_buff *,struct net_device *);
200 static struct net_device_stats *ni52_get_stats(struct net_device *dev);
201 static void set_multicast_list(struct net_device *dev);
202 static void ni52_timeout(struct net_device *dev);
204 static void ni52_dump(struct net_device *,void *);
207 /* helper-functions */
208 static int init586(struct net_device *dev);
209 static int check586(struct net_device *dev,char *where,unsigned size);
210 static void alloc586(struct net_device *dev);
211 static void startrecv586(struct net_device *dev);
212 static void *alloc_rfa(struct net_device *dev,void *ptr);
213 static void ni52_rcv_int(struct net_device *dev);
214 static void ni52_xmt_int(struct net_device *dev);
215 static void ni52_rnr_int(struct net_device *dev);
219 struct net_device_stats stats;
224 volatile struct rfd_struct *rfd_last,*rfd_top,*rfd_first;
225 volatile struct scp_struct *scp; /* volatile is important */
226 volatile struct iscp_struct *iscp; /* volatile is important */
227 volatile struct scb_struct *scb; /* volatile is important */
228 volatile struct tbd_struct *xmit_buffs[NUM_XMIT_BUFFS];
229 #if (NUM_XMIT_BUFFS == 1)
230 volatile struct transmit_cmd_struct *xmit_cmds[2];
231 volatile struct nop_cmd_struct *nop_cmds[2];
233 volatile struct transmit_cmd_struct *xmit_cmds[NUM_XMIT_BUFFS];
234 volatile struct nop_cmd_struct *nop_cmds[NUM_XMIT_BUFFS];
236 volatile int nop_point,num_recv_buffs;
237 volatile char *xmit_cbuffs[NUM_XMIT_BUFFS];
238 volatile int xmit_count,xmit_last;
241 /**********************************************
244 static int ni52_close(struct net_device *dev)
246 free_irq(dev->irq, dev);
248 ni_reset586(); /* the hard way to stop the receiver */
250 netif_stop_queue(dev);
255 /**********************************************
258 static int ni52_open(struct net_device *dev)
268 ret = request_irq(dev->irq, &ni52_interrupt,0,dev->name,dev);
275 netif_start_queue(dev);
277 return 0; /* most done by init */
280 /**********************************************
281 * Check to see if there's an 82586 out there.
283 static int check586(struct net_device *dev,char *where,unsigned size)
286 struct priv *p = /* (struct priv *) dev->priv*/ &pb;
290 p->base = (unsigned long) isa_bus_to_virt((unsigned long)where) + size - 0x01000000;
291 p->memtop = isa_bus_to_virt((unsigned long)where) + size;
292 p->scp = (struct scp_struct *)(p->base + SCP_DEFAULT_ADDRESS);
293 memset((char *)p->scp,0, sizeof(struct scp_struct));
294 for(i=0;i<sizeof(struct scp_struct);i++) /* memory was writeable? */
295 if(((char *)p->scp)[i])
297 p->scp->sysbus = SYSBUSVAL; /* 1 = 8Bit-Bus, 0 = 16 Bit */
298 if(p->scp->sysbus != SYSBUSVAL)
301 iscp_addrs[0] = isa_bus_to_virt((unsigned long)where);
302 iscp_addrs[1]= (char *) p->scp - sizeof(struct iscp_struct);
306 p->iscp = (struct iscp_struct *) iscp_addrs[i];
307 memset((char *)p->iscp,0, sizeof(struct iscp_struct));
309 p->scp->iscp = make24(p->iscp);
314 DELAY(1); /* wait a while... */
316 if(p->iscp->busy) /* i82586 clears 'busy' after successful init */
322 /******************************************************************
323 * set iscp at the right place, called by ni52_probe1 and open586.
325 static void alloc586(struct net_device *dev)
327 struct priv *p = (struct priv *) dev->priv;
332 p->scp = (struct scp_struct *) (p->base + SCP_DEFAULT_ADDRESS);
333 p->scb = (struct scb_struct *) isa_bus_to_virt(dev->mem_start);
334 p->iscp = (struct iscp_struct *) ((char *)p->scp - sizeof(struct iscp_struct));
336 memset((char *) p->iscp,0,sizeof(struct iscp_struct));
337 memset((char *) p->scp ,0,sizeof(struct scp_struct));
339 p->scp->iscp = make24(p->iscp);
340 p->scp->sysbus = SYSBUSVAL;
341 p->iscp->scb_offset = make16(p->scb);
350 printk("%s: Init-Problems (alloc).\n",dev->name);
354 memset((char *)p->scb,0,sizeof(struct scb_struct));
357 /* set: io,irq,memstart,memend or set it when calling insmod */
360 static long memstart; /* e.g 0xd0000 */
361 static long memend; /* e.g 0xd4000 */
363 /**********************************************
364 * probe the ni5210-card
366 struct net_device * __init ni52_probe(int unit)
368 struct net_device *dev = alloc_etherdev(sizeof(struct priv));
369 static int ports[] = {0x300, 0x280, 0x360 , 0x320 , 0x340, 0};
374 return ERR_PTR(-ENOMEM);
377 sprintf(dev->name, "eth%d", unit);
378 netdev_boot_setup_check(dev);
381 memstart = dev->mem_start;
382 memend = dev->mem_end;
385 if (io > 0x1ff) { /* Check a single specified location. */
386 err = ni52_probe1(dev, io);
387 } else if (io > 0) { /* Don't probe at all. */
390 for (port = ports; *port && ni52_probe1(dev, *port) ; port++)
395 for (io = 0x200; io < 0x400 && ni52_probe1(dev, io); io += 8)
405 err = register_netdev(dev);
410 release_region(dev->base_addr, NI52_TOTAL_SIZE);
416 static int __init ni52_probe1(struct net_device *dev,int ioaddr)
420 dev->base_addr = ioaddr;
422 dev->mem_start = memstart;
423 dev->mem_end = memend;
425 if (!request_region(ioaddr, NI52_TOTAL_SIZE, DRV_NAME))
428 if( !(inb(ioaddr+NI52_MAGIC1) == NI52_MAGICVAL1) ||
429 !(inb(ioaddr+NI52_MAGIC2) == NI52_MAGICVAL2)) {
434 for(i=0;i<ETH_ALEN;i++)
435 dev->dev_addr[i] = inb(dev->base_addr+i);
437 if(dev->dev_addr[0] != NI52_ADDR0 || dev->dev_addr[1] != NI52_ADDR1
438 || dev->dev_addr[2] != NI52_ADDR2) {
443 printk(KERN_INFO "%s: NI5210 found at %#3lx, ",dev->name,dev->base_addr);
446 * check (or search) IO-Memory, 8K and 16K
449 size = dev->mem_end - dev->mem_start;
450 if(size != 0x2000 && size != 0x4000) {
451 printk("\n%s: Illegal memory size %d. Allowed is 0x2000 or 0x4000 bytes.\n",dev->name,size);
455 if(!check586(dev,(char *) dev->mem_start,size)) {
456 printk("?memcheck, Can't find memory at 0x%lx with size %d!\n",dev->mem_start,size);
461 if(dev->mem_start != 0) /* no auto-mem-probe */
463 size = 0x4000; /* check for 16K mem */
464 if(!check586(dev,(char *) dev->mem_start,size)) {
465 size = 0x2000; /* check for 8K mem */
466 if(!check586(dev,(char *) dev->mem_start,size)) {
467 printk("?memprobe, Can't find memory at 0x%lx!\n",dev->mem_start);
475 static long memaddrs[] = { 0xc8000,0xca000,0xcc000,0xce000,0xd0000,0xd2000,
476 0xd4000,0xd6000,0xd8000,0xda000,0xdc000, 0 };
480 printk("?memprobe, Can't find io-memory!\n");
484 dev->mem_start = memaddrs[i];
485 size = 0x2000; /* check for 8K mem */
486 if(check586(dev,(char *)dev->mem_start,size)) /* 8K-check */
488 size = 0x4000; /* check for 16K mem */
489 if(check586(dev,(char *)dev->mem_start,size)) /* 16K-check */
493 dev->mem_end = dev->mem_start + size; /* set mem_end showed by 'ifconfig' */
496 memset((char *) dev->priv,0,sizeof(struct priv));
498 ((struct priv *) (dev->priv))->memtop = isa_bus_to_virt(dev->mem_start) + size;
499 ((struct priv *) (dev->priv))->base = (unsigned long) isa_bus_to_virt(dev->mem_start) + size - 0x01000000;
502 /* set number of receive-buffs according to memsize */
504 ((struct priv *) dev->priv)->num_recv_buffs = NUM_RECV_BUFFS_8;
506 ((struct priv *) dev->priv)->num_recv_buffs = NUM_RECV_BUFFS_16;
508 printk("Memaddr: 0x%lx, Memsize: %d, ",dev->mem_start,size);
512 unsigned long irq_mask;
514 irq_mask = probe_irq_on();
519 dev->irq = probe_irq_off(irq_mask);
522 printk("?autoirq, Failed to detect IRQ line!\n");
526 printk("IRQ %d (autodetected).\n",dev->irq);
531 printk("IRQ %d (assigned and not checked!).\n",dev->irq);
534 dev->open = ni52_open;
535 dev->stop = ni52_close;
536 dev->get_stats = ni52_get_stats;
537 dev->tx_timeout = ni52_timeout;
538 dev->watchdog_timeo = HZ/20;
539 dev->hard_start_xmit = ni52_send_packet;
540 dev->set_multicast_list = set_multicast_list;
546 release_region(ioaddr, NI52_TOTAL_SIZE);
550 /**********************************************
551 * init the chip (ni52-interrupt should be disabled?!)
552 * needs a correct 'allocated' memory
555 static int init586(struct net_device *dev)
559 struct priv *p = (struct priv *) dev->priv;
560 volatile struct configure_cmd_struct *cfg_cmd;
561 volatile struct iasetup_cmd_struct *ias_cmd;
562 volatile struct tdr_cmd_struct *tdr_cmd;
563 volatile struct mcsetup_cmd_struct *mc_cmd;
564 struct dev_mc_list *dmi=dev->mc_list;
565 int num_addrs=dev->mc_count;
567 ptr = (void *) ((char *)p->scb + sizeof(struct scb_struct));
569 cfg_cmd = (struct configure_cmd_struct *)ptr; /* configure-command */
570 cfg_cmd->cmd_status = 0;
571 cfg_cmd->cmd_cmd = CMD_CONFIGURE | CMD_LAST;
572 cfg_cmd->cmd_link = 0xffff;
574 cfg_cmd->byte_cnt = 0x0a; /* number of cfg bytes */
575 cfg_cmd->fifo = fifo; /* fifo-limit (8=tx:32/rx:64) */
576 cfg_cmd->sav_bf = 0x40; /* hold or discard bad recv frames (bit 7) */
577 cfg_cmd->adr_len = 0x2e; /* addr_len |!src_insert |pre-len |loopback */
578 cfg_cmd->priority = 0x00;
580 cfg_cmd->time_low = 0x00;
581 cfg_cmd->time_high = 0xf2;
582 cfg_cmd->promisc = 0;
583 if(dev->flags & IFF_ALLMULTI) {
584 int len = ((char *) p->iscp - (char *) ptr - 8) / 6;
585 if(num_addrs > len) {
586 printk("%s: switching to promisc. mode\n",dev->name);
587 dev->flags|=IFF_PROMISC;
590 if(dev->flags&IFF_PROMISC)
593 dev->flags|=IFF_PROMISC;
595 cfg_cmd->carr_coll = 0x00;
597 p->scb->cbl_offset = make16(cfg_cmd);
600 p->scb->cmd_cuc = CUC_START; /* cmd.-unit start */
603 WAIT_4_STAT_COMPL(cfg_cmd);
605 if((cfg_cmd->cmd_status & (STAT_OK|STAT_COMPL)) != (STAT_COMPL|STAT_OK))
607 printk("%s: configure command failed: %x\n",dev->name,cfg_cmd->cmd_status);
612 * individual address setup
615 ias_cmd = (struct iasetup_cmd_struct *)ptr;
617 ias_cmd->cmd_status = 0;
618 ias_cmd->cmd_cmd = CMD_IASETUP | CMD_LAST;
619 ias_cmd->cmd_link = 0xffff;
621 memcpy((char *)&ias_cmd->iaddr,(char *) dev->dev_addr,ETH_ALEN);
623 p->scb->cbl_offset = make16(ias_cmd);
625 p->scb->cmd_cuc = CUC_START; /* cmd.-unit start */
628 WAIT_4_STAT_COMPL(ias_cmd);
630 if((ias_cmd->cmd_status & (STAT_OK|STAT_COMPL)) != (STAT_OK|STAT_COMPL)) {
631 printk("%s (ni52): individual address setup command failed: %04x\n",dev->name,ias_cmd->cmd_status);
636 * TDR, wire check .. e.g. no resistor e.t.c
639 tdr_cmd = (struct tdr_cmd_struct *)ptr;
641 tdr_cmd->cmd_status = 0;
642 tdr_cmd->cmd_cmd = CMD_TDR | CMD_LAST;
643 tdr_cmd->cmd_link = 0xffff;
646 p->scb->cbl_offset = make16(tdr_cmd);
647 p->scb->cmd_cuc = CUC_START; /* cmd.-unit start */
650 WAIT_4_STAT_COMPL(tdr_cmd);
652 if(!(tdr_cmd->cmd_status & STAT_COMPL))
654 printk("%s: Problems while running the TDR.\n",dev->name);
658 DELAY_16(); /* wait for result */
659 result = tdr_cmd->status;
661 p->scb->cmd_cuc = p->scb->cus & STAT_MASK;
662 ni_attn586(); /* ack the interrupts */
664 if(result & TDR_LNK_OK)
666 else if(result & TDR_XCVR_PRB)
667 printk("%s: TDR: Transceiver problem. Check the cable(s)!\n",dev->name);
668 else if(result & TDR_ET_OPN)
669 printk("%s: TDR: No correct termination %d clocks away.\n",dev->name,result & TDR_TIMEMASK);
670 else if(result & TDR_ET_SRT)
672 if (result & TDR_TIMEMASK) /* time == 0 -> strange :-) */
673 printk("%s: TDR: Detected a short circuit %d clocks away.\n",dev->name,result & TDR_TIMEMASK);
676 printk("%s: TDR: Unknown status %04x\n",dev->name,result);
682 if(num_addrs && !(dev->flags & IFF_PROMISC) )
684 mc_cmd = (struct mcsetup_cmd_struct *) ptr;
685 mc_cmd->cmd_status = 0;
686 mc_cmd->cmd_cmd = CMD_MCSETUP | CMD_LAST;
687 mc_cmd->cmd_link = 0xffff;
688 mc_cmd->mc_cnt = num_addrs * 6;
690 for(i=0;i<num_addrs;i++,dmi=dmi->next)
691 memcpy((char *) mc_cmd->mc_list[i], dmi->dmi_addr,6);
693 p->scb->cbl_offset = make16(mc_cmd);
694 p->scb->cmd_cuc = CUC_START;
697 WAIT_4_STAT_COMPL(mc_cmd);
699 if( (mc_cmd->cmd_status & (STAT_COMPL|STAT_OK)) != (STAT_COMPL|STAT_OK) )
700 printk("%s: Can't apply multicast-address-list.\n",dev->name);
704 * alloc nop/xmit-cmds
706 #if (NUM_XMIT_BUFFS == 1)
709 p->nop_cmds[i] = (struct nop_cmd_struct *)ptr;
710 p->nop_cmds[i]->cmd_cmd = CMD_NOP;
711 p->nop_cmds[i]->cmd_status = 0;
712 p->nop_cmds[i]->cmd_link = make16((p->nop_cmds[i]));
713 ptr = (char *) ptr + sizeof(struct nop_cmd_struct);
716 for(i=0;i<NUM_XMIT_BUFFS;i++)
718 p->nop_cmds[i] = (struct nop_cmd_struct *)ptr;
719 p->nop_cmds[i]->cmd_cmd = CMD_NOP;
720 p->nop_cmds[i]->cmd_status = 0;
721 p->nop_cmds[i]->cmd_link = make16((p->nop_cmds[i]));
722 ptr = (char *) ptr + sizeof(struct nop_cmd_struct);
726 ptr = alloc_rfa(dev,(void *)ptr); /* init receive-frame-area */
729 * alloc xmit-buffs / init xmit_cmds
731 for(i=0;i<NUM_XMIT_BUFFS;i++)
733 p->xmit_cmds[i] = (struct transmit_cmd_struct *)ptr; /*transmit cmd/buff 0*/
734 ptr = (char *) ptr + sizeof(struct transmit_cmd_struct);
735 p->xmit_cbuffs[i] = (char *)ptr; /* char-buffs */
736 ptr = (char *) ptr + XMIT_BUFF_SIZE;
737 p->xmit_buffs[i] = (struct tbd_struct *)ptr; /* TBD */
738 ptr = (char *) ptr + sizeof(struct tbd_struct);
739 if((void *)ptr > (void *)p->iscp)
741 printk("%s: not enough shared-mem for your configuration!\n",dev->name);
744 memset((char *)(p->xmit_cmds[i]) ,0, sizeof(struct transmit_cmd_struct));
745 memset((char *)(p->xmit_buffs[i]),0, sizeof(struct tbd_struct));
746 p->xmit_cmds[i]->cmd_link = make16(p->nop_cmds[(i+1)%NUM_XMIT_BUFFS]);
747 p->xmit_cmds[i]->cmd_status = STAT_COMPL;
748 p->xmit_cmds[i]->cmd_cmd = CMD_XMIT | CMD_INT;
749 p->xmit_cmds[i]->tbd_offset = make16((p->xmit_buffs[i]));
750 p->xmit_buffs[i]->next = 0xffff;
751 p->xmit_buffs[i]->buffer = make24((p->xmit_cbuffs[i]));
756 #ifndef NO_NOPCOMMANDS
761 * 'start transmitter'
763 #ifndef NO_NOPCOMMANDS
764 p->scb->cbl_offset = make16(p->nop_cmds[0]);
765 p->scb->cmd_cuc = CUC_START;
769 p->xmit_cmds[0]->cmd_link = make16(p->xmit_cmds[0]);
770 p->xmit_cmds[0]->cmd_cmd = CMD_XMIT | CMD_SUSPEND | CMD_INT;
776 p->scb->cmd_cuc = p->scb->cus & STAT_MASK;
785 /******************************************************
786 * This is a helper routine for ni52_rnr_int() and init586().
787 * It sets up the Receive Frame Area (RFA).
790 static void *alloc_rfa(struct net_device *dev,void *ptr)
792 volatile struct rfd_struct *rfd = (struct rfd_struct *)ptr;
793 volatile struct rbd_struct *rbd;
795 struct priv *p = (struct priv *) dev->priv;
797 memset((char *) rfd,0,sizeof(struct rfd_struct)*(p->num_recv_buffs+rfdadd));
800 for(i = 0; i < (p->num_recv_buffs+rfdadd); i++) {
801 rfd[i].next = make16(rfd + (i+1) % (p->num_recv_buffs+rfdadd) );
802 rfd[i].rbd_offset = 0xffff;
804 rfd[p->num_recv_buffs-1+rfdadd].last = RFD_SUSP; /* RU suspend */
806 ptr = (void *) (rfd + (p->num_recv_buffs + rfdadd) );
808 rbd = (struct rbd_struct *) ptr;
809 ptr = (void *) (rbd + p->num_recv_buffs);
811 /* clr descriptors */
812 memset((char *) rbd,0,sizeof(struct rbd_struct)*(p->num_recv_buffs));
814 for(i=0;i<p->num_recv_buffs;i++)
816 rbd[i].next = make16((rbd + (i+1) % p->num_recv_buffs));
817 rbd[i].size = RECV_BUFF_SIZE;
818 rbd[i].buffer = make24(ptr);
819 ptr = (char *) ptr + RECV_BUFF_SIZE;
822 p->rfd_top = p->rfd_first;
823 p->rfd_last = p->rfd_first + (p->num_recv_buffs - 1 + rfdadd);
825 p->scb->rfa_offset = make16(p->rfd_first);
826 p->rfd_first->rbd_offset = make16(rbd);
832 /**************************************************
833 * Interrupt Handler ...
836 static irqreturn_t ni52_interrupt(int irq,void *dev_id)
838 struct net_device *dev = dev_id;
844 printk ("ni5210-interrupt: irq %d for unknown device.\n",irq);
847 p = (struct priv *) dev->priv;
852 WAIT_4_SCB_CMD(); /* wait for last command */
854 while((stat=p->scb->cus & STAT_MASK))
856 p->scb->cmd_cuc = stat;
859 if(stat & STAT_FR) /* received a frame */
862 if(stat & STAT_RNR) /* RU went 'not ready' */
865 if(p->scb->rus & RU_SUSPEND) /* special case: RU_SUSPEND */
868 p->scb->cmd_ruc = RUC_RESUME;
870 WAIT_4_SCB_CMD_RUC();
874 printk("%s: Receiver-Unit went 'NOT READY': %04x/%02x.\n",dev->name,(int) stat,(int) p->scb->rus);
879 if(stat & STAT_CX) /* command with I-bit set complete */
882 #ifndef NO_NOPCOMMANDS
883 if(stat & STAT_CNA) /* CU went 'not ready' */
885 if(netif_running(dev))
886 printk("%s: oops! CU has left active state. stat: %04x/%02x.\n",dev->name,(int) stat,(int) p->scb->cus);
893 WAIT_4_SCB_CMD(); /* wait for ack. (ni52_xmt_int can be faster than ack!!) */
894 if(p->scb->cmd_cuc) /* timed out? */
896 printk("%s: Acknowledge timed out.\n",dev->name);
907 /*******************************************************
911 static void ni52_rcv_int(struct net_device *dev)
914 unsigned short totlen;
916 struct rbd_struct *rbd;
917 struct priv *p = (struct priv *) dev->priv;
922 for(;(status = p->rfd_top->stat_high) & RFD_COMPL;)
924 rbd = (struct rbd_struct *) make32(p->rfd_top->rbd_offset);
926 if(status & RFD_OK) /* frame received without error? */
928 if( (totlen = rbd->status) & RBD_LAST) /* the first and the last buffer? */
930 totlen &= RBD_MASK; /* length of this frame */
932 skb = (struct sk_buff *) dev_alloc_skb(totlen+2);
937 skb_copy_to_linear_data(skb,(char *) p->base+(unsigned long) rbd->buffer,totlen);
938 skb->protocol=eth_type_trans(skb,dev);
940 dev->last_rx = jiffies;
941 p->stats.rx_packets++;
942 p->stats.rx_bytes += totlen;
945 p->stats.rx_dropped++;
950 /* free all RBD's until RBD_LAST is set */
952 while(!((rstat=rbd->status) & RBD_LAST))
954 totlen += rstat & RBD_MASK;
957 printk("%s: Whoops .. no end mark in RBD list\n",dev->name);
961 rbd = (struct rbd_struct *) make32(rbd->next);
963 totlen += rstat & RBD_MASK;
965 printk("%s: received oversized frame! length: %d\n",dev->name,totlen);
966 p->stats.rx_dropped++;
969 else /* frame !(ok), only with 'save-bad-frames' */
971 printk("%s: oops! rfd-error-status: %04x\n",dev->name,status);
972 p->stats.rx_errors++;
974 p->rfd_top->stat_high = 0;
975 p->rfd_top->last = RFD_SUSP; /* maybe exchange by RFD_LAST */
976 p->rfd_top->rbd_offset = 0xffff;
977 p->rfd_last->last = 0; /* delete RFD_SUSP */
978 p->rfd_last = p->rfd_top;
979 p->rfd_top = (struct rfd_struct *) make32(p->rfd_top->next); /* step to next RFD */
980 p->scb->rfa_offset = make16(p->rfd_top);
989 p->scb->cmd_ruc = RUC_RESUME;
991 WAIT_4_SCB_CMD_RUC();
999 if(p->rfd_top->status)
1003 printk("%s: RU hasn't fetched next RFD (not busy/complete)\n",dev->name);
1012 volatile struct rfd_struct *rfds=p->rfd_top;
1013 volatile struct rbd_struct *rbds;
1014 printk("%s: received a FC intr. without having a frame: %04x %d\n",dev->name,status,old_at_least);
1015 for(i=0;i< (p->num_recv_buffs+4);i++)
1017 rbds = (struct rbd_struct *) make32(rfds->rbd_offset);
1018 printk("%04x:%04x ",rfds->status,rbds->status);
1019 rfds = (struct rfd_struct *) make32(rfds->next);
1021 printk("\nerrs: %04x %04x stat: %04x\n",(int)p->scb->rsc_errs,(int)p->scb->ovrn_errs,(int)p->scb->status);
1022 printk("\nerrs: %04x %04x rus: %02x, cus: %02x\n",(int)p->scb->rsc_errs,(int)p->scb->ovrn_errs,(int)p->scb->rus,(int)p->scb->cus);
1024 old_at_least = at_least_one;
1031 /**********************************************************
1032 * handle 'Receiver went not ready'.
1035 static void ni52_rnr_int(struct net_device *dev)
1037 struct priv *p = (struct priv *) dev->priv;
1039 p->stats.rx_errors++;
1041 WAIT_4_SCB_CMD(); /* wait for the last cmd, WAIT_4_FULLSTAT?? */
1042 p->scb->cmd_ruc = RUC_ABORT; /* usually the RU is in the 'no resource'-state .. abort it now. */
1044 WAIT_4_SCB_CMD_RUC(); /* wait for accept cmd. */
1046 alloc_rfa(dev,(char *)p->rfd_first);
1047 /* maybe add a check here, before restarting the RU */
1048 startrecv586(dev); /* restart RU */
1050 printk("%s: Receive-Unit restarted. Status: %04x\n",dev->name,p->scb->rus);
1054 /**********************************************************
1055 * handle xmit - interrupt
1058 static void ni52_xmt_int(struct net_device *dev)
1061 struct priv *p = (struct priv *) dev->priv;
1066 status = p->xmit_cmds[p->xmit_last]->cmd_status;
1067 if(!(status & STAT_COMPL))
1068 printk("%s: strange .. xmit-int without a 'COMPLETE'\n",dev->name);
1070 if(status & STAT_OK)
1072 p->stats.tx_packets++;
1073 p->stats.collisions += (status & TCMD_MAXCOLLMASK);
1077 p->stats.tx_errors++;
1078 if(status & TCMD_LATECOLL) {
1079 printk("%s: late collision detected.\n",dev->name);
1080 p->stats.collisions++;
1082 else if(status & TCMD_NOCARRIER) {
1083 p->stats.tx_carrier_errors++;
1084 printk("%s: no carrier detected.\n",dev->name);
1086 else if(status & TCMD_LOSTCTS)
1087 printk("%s: loss of CTS detected.\n",dev->name);
1088 else if(status & TCMD_UNDERRUN) {
1089 p->stats.tx_fifo_errors++;
1090 printk("%s: DMA underrun detected.\n",dev->name);
1092 else if(status & TCMD_MAXCOLL) {
1093 printk("%s: Max. collisions exceeded.\n",dev->name);
1094 p->stats.collisions += 16;
1098 #if (NUM_XMIT_BUFFS > 1)
1099 if( (++p->xmit_last) == NUM_XMIT_BUFFS)
1102 netif_wake_queue(dev);
1105 /***********************************************************
1106 * (re)start the receiver
1109 static void startrecv586(struct net_device *dev)
1111 struct priv *p = (struct priv *) dev->priv;
1114 WAIT_4_SCB_CMD_RUC();
1115 p->scb->rfa_offset = make16(p->rfd_first);
1116 p->scb->cmd_ruc = RUC_START;
1117 ni_attn586(); /* start cmd. */
1118 WAIT_4_SCB_CMD_RUC(); /* wait for accept cmd. (no timeout!!) */
1121 static void ni52_timeout(struct net_device *dev)
1123 struct priv *p = (struct priv *) dev->priv;
1124 #ifndef NO_NOPCOMMANDS
1125 if(p->scb->cus & CU_ACTIVE) /* COMMAND-UNIT active? */
1127 netif_wake_queue(dev);
1129 printk("%s: strange ... timeout with CU active?!?\n",dev->name);
1130 printk("%s: X0: %04x N0: %04x N1: %04x %d\n",dev->name,(int)p->xmit_cmds[0]->cmd_status,(int)p->nop_cmds[0]->cmd_status,(int)p->nop_cmds[1]->cmd_status,(int)p->nop_point);
1132 p->scb->cmd_cuc = CUC_ABORT;
1135 p->scb->cbl_offset = make16(p->nop_cmds[p->nop_point]);
1136 p->scb->cmd_cuc = CUC_START;
1139 dev->trans_start = jiffies;
1145 printk("%s: xmitter timed out, try to restart! stat: %02x\n",dev->name,p->scb->cus);
1146 printk("%s: command-stats: %04x %04x\n",dev->name,p->xmit_cmds[0]->cmd_status,p->xmit_cmds[1]->cmd_status);
1147 printk("%s: check, whether you set the right interrupt number!\n",dev->name);
1152 dev->trans_start = jiffies;
1155 /******************************************************
1159 static int ni52_send_packet(struct sk_buff *skb, struct net_device *dev)
1162 #ifndef NO_NOPCOMMANDS
1165 struct priv *p = (struct priv *) dev->priv;
1167 if(skb->len > XMIT_BUFF_SIZE)
1169 printk("%s: Sorry, max. framelength is %d bytes. The length of your frame is %d bytes.\n",dev->name,XMIT_BUFF_SIZE,skb->len);
1173 netif_stop_queue(dev);
1175 #if(NUM_XMIT_BUFFS > 1)
1176 if(test_and_set_bit(0,(void *) &p->lock)) {
1177 printk("%s: Queue was locked\n",dev->name);
1183 skb_copy_from_linear_data(skb, (char *) p->xmit_cbuffs[p->xmit_count], skb->len);
1185 if (len < ETH_ZLEN) {
1187 memset((char *)p->xmit_cbuffs[p->xmit_count]+skb->len, 0, len - skb->len);
1190 #if (NUM_XMIT_BUFFS == 1)
1191 # ifdef NO_NOPCOMMANDS
1194 if(p->scb->cus & CU_ACTIVE)
1196 printk("%s: Hmmm .. CU is still running and we wanna send a new packet.\n",dev->name);
1197 printk("%s: stat: %04x %04x\n",dev->name,p->scb->cus,p->xmit_cmds[0]->cmd_status);
1201 p->xmit_buffs[0]->size = TBD_LAST | len;
1204 p->xmit_cmds[0]->cmd_status = 0;
1206 if( (p->scb->cus & CU_STATUS) == CU_SUSPEND)
1207 p->scb->cmd_cuc = CUC_RESUME;
1210 p->scb->cbl_offset = make16(p->xmit_cmds[0]);
1211 p->scb->cmd_cuc = CUC_START;
1215 dev->trans_start = jiffies;
1219 if( (p->scb->cus & CU_ACTIVE)) /* test it, because CU sometimes doesn't start immediately */
1221 if(p->xmit_cmds[0]->cmd_status)
1224 printk("%s: Can't start transmit-command.\n",dev->name);
1227 next_nop = (p->nop_point + 1) & 0x1;
1228 p->xmit_buffs[0]->size = TBD_LAST | len;
1230 p->xmit_cmds[0]->cmd_link = p->nop_cmds[next_nop]->cmd_link
1231 = make16((p->nop_cmds[next_nop]));
1232 p->xmit_cmds[0]->cmd_status = p->nop_cmds[next_nop]->cmd_status = 0;
1234 p->nop_cmds[p->nop_point]->cmd_link = make16((p->xmit_cmds[0]));
1235 dev->trans_start = jiffies;
1236 p->nop_point = next_nop;
1240 p->xmit_buffs[p->xmit_count]->size = TBD_LAST | len;
1241 if( (next_nop = p->xmit_count + 1) == NUM_XMIT_BUFFS )
1244 p->xmit_cmds[p->xmit_count]->cmd_status = 0;
1245 /* linkpointer of xmit-command already points to next nop cmd */
1246 p->nop_cmds[next_nop]->cmd_link = make16((p->nop_cmds[next_nop]));
1247 p->nop_cmds[next_nop]->cmd_status = 0;
1249 p->nop_cmds[p->xmit_count]->cmd_link = make16((p->xmit_cmds[p->xmit_count]));
1250 dev->trans_start = jiffies;
1251 p->xmit_count = next_nop;
1254 unsigned long flags;
1257 if(p->xmit_count != p->xmit_last)
1258 netif_wake_queue(dev);
1260 restore_flags(flags);
1268 /*******************************************
1269 * Someone wanna have the statistics
1272 static struct net_device_stats *ni52_get_stats(struct net_device *dev)
1274 struct priv *p = (struct priv *) dev->priv;
1275 unsigned short crc,aln,rsc,ovrn;
1277 crc = p->scb->crc_errs; /* get error-statistic from the ni82586 */
1278 p->scb->crc_errs = 0;
1279 aln = p->scb->aln_errs;
1280 p->scb->aln_errs = 0;
1281 rsc = p->scb->rsc_errs;
1282 p->scb->rsc_errs = 0;
1283 ovrn = p->scb->ovrn_errs;
1284 p->scb->ovrn_errs = 0;
1286 p->stats.rx_crc_errors += crc;
1287 p->stats.rx_fifo_errors += ovrn;
1288 p->stats.rx_frame_errors += aln;
1289 p->stats.rx_dropped += rsc;
1294 /********************************************************
1298 static void set_multicast_list(struct net_device *dev)
1300 netif_stop_queue(dev);
1306 netif_wake_queue(dev);
1310 static struct net_device *dev_ni52;
1312 module_param(io, int, 0);
1313 module_param(irq, int, 0);
1314 module_param(memstart, long, 0);
1315 module_param(memend, long, 0);
1316 MODULE_PARM_DESC(io, "NI5210 I/O base address,required");
1317 MODULE_PARM_DESC(irq, "NI5210 IRQ number,required");
1318 MODULE_PARM_DESC(memstart, "NI5210 memory base address,required");
1319 MODULE_PARM_DESC(memend, "NI5210 memory end address,required");
1321 int __init init_module(void)
1323 if(io <= 0x0 || !memend || !memstart || irq < 2) {
1324 printk("ni52: Autoprobing not allowed for modules.\nni52: Set symbols 'io' 'irq' 'memstart' and 'memend'\n");
1327 dev_ni52 = ni52_probe(-1);
1328 if (IS_ERR(dev_ni52))
1329 return PTR_ERR(dev_ni52);
1333 void __exit cleanup_module(void)
1335 unregister_netdev(dev_ni52);
1336 release_region(dev_ni52->base_addr, NI52_TOTAL_SIZE);
1337 free_netdev(dev_ni52);
1343 * DUMP .. we expect a not running CMD unit and enough space
1345 void ni52_dump(struct net_device *dev,void *ptr)
1347 struct priv *p = (struct priv *) dev->priv;
1348 struct dump_cmd_struct *dump_cmd = (struct dump_cmd_struct *) ptr;
1351 p->scb->cmd_cuc = CUC_ABORT;
1354 WAIT_4_SCB_CMD_RUC();
1356 dump_cmd->cmd_status = 0;
1357 dump_cmd->cmd_cmd = CMD_DUMP | CMD_LAST;
1358 dump_cmd->dump_offset = make16((dump_cmd + 1));
1359 dump_cmd->cmd_link = 0xffff;
1361 p->scb->cbl_offset = make16(dump_cmd);
1362 p->scb->cmd_cuc = CUC_START;
1364 WAIT_4_STAT_COMPL(dump_cmd);
1366 if( (dump_cmd->cmd_status & (STAT_COMPL|STAT_OK)) != (STAT_COMPL|STAT_OK) )
1367 printk("%s: Can't get dump information.\n",dev->name);
1369 for(i=0;i<170;i++) {
1370 printk("%02x ",(int) ((unsigned char *) (dump_cmd + 1))[i]);
1377 MODULE_LICENSE("GPL");
1380 * END: linux/drivers/net/ni52.c