5 this file has configuration informations - card-specific stuff
6 like the big tvcards array for the most part
8 Copyright (C) 1996,97,98 Ralph Metzler (rjkm@thp.uni-koeln.de)
9 & Marcus Metzler (mocm@thp.uni-koeln.de)
10 (c) 1999-2001 Gerd Knorr <kraxel@goldbach.in-berlin.de>
12 This program is free software; you can redistribute it and/or modify
13 it under the terms of the GNU General Public License as published by
14 the Free Software Foundation; either version 2 of the License, or
15 (at your option) any later version.
17 This program is distributed in the hope that it will be useful,
18 but WITHOUT ANY WARRANTY; without even the implied warranty of
19 MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
20 GNU General Public License for more details.
22 You should have received a copy of the GNU General Public License
23 along with this program; if not, write to the Free Software
24 Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA.
28 #include <linux/delay.h>
29 #include <linux/module.h>
30 #include <linux/kmod.h>
31 #include <linux/init.h>
32 #include <linux/pci.h>
33 #include <linux/vmalloc.h>
34 #include <linux/firmware.h>
35 #include <net/checksum.h>
40 #include <media/v4l2-common.h>
41 #include <media/tvaudio.h>
42 #include "bttv-audio-hook.h"
45 static void boot_msp34xx(struct bttv *btv, int pin);
46 static void boot_bt832(struct bttv *btv);
47 static void hauppauge_eeprom(struct bttv *btv);
48 static void avermedia_eeprom(struct bttv *btv);
49 static void osprey_eeprom(struct bttv *btv, const u8 ee[256]);
50 static void modtec_eeprom(struct bttv *btv);
51 static void init_PXC200(struct bttv *btv);
52 static void init_RTV24(struct bttv *btv);
54 static void rv605_muxsel(struct bttv *btv, unsigned int input);
55 static void eagle_muxsel(struct bttv *btv, unsigned int input);
56 static void xguard_muxsel(struct bttv *btv, unsigned int input);
57 static void ivc120_muxsel(struct bttv *btv, unsigned int input);
58 static void gvc1100_muxsel(struct bttv *btv, unsigned int input);
60 static void PXC200_muxsel(struct bttv *btv, unsigned int input);
62 static void picolo_tetra_muxsel(struct bttv *btv, unsigned int input);
63 static void picolo_tetra_init(struct bttv *btv);
65 static void tibetCS16_muxsel(struct bttv *btv, unsigned int input);
66 static void tibetCS16_init(struct bttv *btv);
68 static void kodicom4400r_muxsel(struct bttv *btv, unsigned int input);
69 static void kodicom4400r_init(struct bttv *btv);
71 static void sigmaSLC_muxsel(struct bttv *btv, unsigned int input);
72 static void sigmaSQ_muxsel(struct bttv *btv, unsigned int input);
74 static int terratec_active_radio_upgrade(struct bttv *btv);
75 static int tea5757_read(struct bttv *btv);
76 static int tea5757_write(struct bttv *btv, int value);
77 static void identify_by_eeprom(struct bttv *btv,
78 unsigned char eeprom_data[256]);
79 static int __devinit pvr_boot(struct bttv *btv);
81 /* config variables */
82 static unsigned int triton1;
83 static unsigned int vsfx;
84 static unsigned int latency = UNSET;
87 static unsigned int card[BTTV_MAX] = { [ 0 ... (BTTV_MAX-1) ] = UNSET };
88 static unsigned int pll[BTTV_MAX] = { [ 0 ... (BTTV_MAX-1) ] = UNSET };
89 static unsigned int tuner[BTTV_MAX] = { [ 0 ... (BTTV_MAX-1) ] = UNSET };
90 static unsigned int svhs[BTTV_MAX] = { [ 0 ... (BTTV_MAX-1) ] = UNSET };
91 static unsigned int remote[BTTV_MAX] = { [ 0 ... (BTTV_MAX-1) ] = UNSET };
92 static struct bttv *master[BTTV_MAX] = { [ 0 ... (BTTV_MAX-1) ] = NULL };
94 static unsigned int autoload = 1;
96 static unsigned int autoload;
98 static unsigned int gpiomask = UNSET;
99 static unsigned int audioall = UNSET;
100 static unsigned int audiomux[5] = { [ 0 ... 4 ] = UNSET };
103 module_param(triton1, int, 0444);
104 module_param(vsfx, int, 0444);
105 module_param(no_overlay, int, 0444);
106 module_param(latency, int, 0444);
107 module_param(gpiomask, int, 0444);
108 module_param(audioall, int, 0444);
109 module_param(autoload, int, 0444);
111 module_param_array(card, int, NULL, 0444);
112 module_param_array(pll, int, NULL, 0444);
113 module_param_array(tuner, int, NULL, 0444);
114 module_param_array(svhs, int, NULL, 0444);
115 module_param_array(remote, int, NULL, 0444);
116 module_param_array(audiomux, int, NULL, 0444);
118 MODULE_PARM_DESC(triton1,"set ETBF pci config bit "
119 "[enable bug compatibility for triton1 + others]");
120 MODULE_PARM_DESC(vsfx,"set VSFX pci config bit "
121 "[yet another chipset flaw workaround]");
122 MODULE_PARM_DESC(latency,"pci latency timer");
123 MODULE_PARM_DESC(card,"specify TV/grabber card model, see CARDLIST file for a list");
124 MODULE_PARM_DESC(pll,"specify installed crystal (0=none, 28=28 MHz, 35=35 MHz)");
125 MODULE_PARM_DESC(tuner,"specify installed tuner type");
126 MODULE_PARM_DESC(autoload,"automatically load i2c modules like tuner.o, default is 1 (yes)");
127 MODULE_PARM_DESC(no_overlay,"allow override overlay default (0 disables, 1 enables)"
128 " [some VIA/SIS chipsets are known to have problem with overlay]");
130 /* ----------------------------------------------------------------------- */
131 /* list of card IDs for bt878+ cards */
137 } cards[] __devinitdata = {
138 { 0x13eb0070, BTTV_BOARD_HAUPPAUGE878, "Hauppauge WinTV" },
139 { 0x39000070, BTTV_BOARD_HAUPPAUGE878, "Hauppauge WinTV-D" },
140 { 0x45000070, BTTV_BOARD_HAUPPAUGEPVR, "Hauppauge WinTV/PVR" },
141 { 0xff000070, BTTV_BOARD_OSPREY1x0, "Osprey-100" },
142 { 0xff010070, BTTV_BOARD_OSPREY2x0_SVID,"Osprey-200" },
143 { 0xff020070, BTTV_BOARD_OSPREY500, "Osprey-500" },
144 { 0xff030070, BTTV_BOARD_OSPREY2000, "Osprey-2000" },
145 { 0xff040070, BTTV_BOARD_OSPREY540, "Osprey-540" },
146 { 0xff070070, BTTV_BOARD_OSPREY440, "Osprey-440" },
148 { 0x00011002, BTTV_BOARD_ATI_TVWONDER, "ATI TV Wonder" },
149 { 0x00031002, BTTV_BOARD_ATI_TVWONDERVE,"ATI TV Wonder/VE" },
151 { 0x6606107d, BTTV_BOARD_WINFAST2000, "Leadtek WinFast TV 2000" },
152 { 0x6607107d, BTTV_BOARD_WINFASTVC100, "Leadtek WinFast VC 100" },
153 { 0x6609107d, BTTV_BOARD_WINFAST2000, "Leadtek TV 2000 XP" },
154 { 0x263610b4, BTTV_BOARD_STB2, "STB TV PCI FM, Gateway P/N 6000704" },
155 { 0x264510b4, BTTV_BOARD_STB2, "STB TV PCI FM, Gateway P/N 6000704" },
156 { 0x402010fc, BTTV_BOARD_GVBCTV3PCI, "I-O Data Co. GV-BCTV3/PCI" },
157 { 0x405010fc, BTTV_BOARD_GVBCTV4PCI, "I-O Data Co. GV-BCTV4/PCI" },
158 { 0x407010fc, BTTV_BOARD_GVBCTV5PCI, "I-O Data Co. GV-BCTV5/PCI" },
159 { 0xd01810fc, BTTV_BOARD_GVBCTV5PCI, "I-O Data Co. GV-BCTV5/PCI" },
161 { 0x001211bd, BTTV_BOARD_PINNACLE, "Pinnacle PCTV" },
162 /* some cards ship with byteswapped IDs ... */
163 { 0x1200bd11, BTTV_BOARD_PINNACLE, "Pinnacle PCTV [bswap]" },
164 { 0xff00bd11, BTTV_BOARD_PINNACLE, "Pinnacle PCTV [bswap]" },
165 /* this seems to happen as well ... */
166 { 0xff1211bd, BTTV_BOARD_PINNACLE, "Pinnacle PCTV" },
168 { 0x3000121a, BTTV_BOARD_VOODOOTV_200, "3Dfx VoodooTV 200" },
169 { 0x263710b4, BTTV_BOARD_VOODOOTV_FM, "3Dfx VoodooTV FM" },
170 { 0x3060121a, BTTV_BOARD_STB2, "3Dfx VoodooTV 100/ STB OEM" },
172 { 0x3000144f, BTTV_BOARD_MAGICTVIEW063, "(Askey Magic/others) TView99 CPH06x" },
173 { 0xa005144f, BTTV_BOARD_MAGICTVIEW063, "CPH06X TView99-Card" },
174 { 0x3002144f, BTTV_BOARD_MAGICTVIEW061, "(Askey Magic/others) TView99 CPH05x" },
175 { 0x3005144f, BTTV_BOARD_MAGICTVIEW061, "(Askey Magic/others) TView99 CPH061/06L (T1/LC)" },
176 { 0x5000144f, BTTV_BOARD_MAGICTVIEW061, "Askey CPH050" },
177 { 0x300014ff, BTTV_BOARD_MAGICTVIEW061, "TView 99 (CPH061)" },
178 { 0x300214ff, BTTV_BOARD_PHOEBE_TVMAS, "Phoebe TV Master (CPH060)" },
180 { 0x00011461, BTTV_BOARD_AVPHONE98, "AVerMedia TVPhone98" },
181 { 0x00021461, BTTV_BOARD_AVERMEDIA98, "AVermedia TVCapture 98" },
182 { 0x00031461, BTTV_BOARD_AVPHONE98, "AVerMedia TVPhone98" },
183 { 0x00041461, BTTV_BOARD_AVERMEDIA98, "AVerMedia TVCapture 98" },
184 { 0x03001461, BTTV_BOARD_AVERMEDIA98, "VDOMATE TV TUNER CARD" },
186 { 0x1117153b, BTTV_BOARD_TERRATVALUE, "Terratec TValue (Philips PAL B/G)" },
187 { 0x1118153b, BTTV_BOARD_TERRATVALUE, "Terratec TValue (Temic PAL B/G)" },
188 { 0x1119153b, BTTV_BOARD_TERRATVALUE, "Terratec TValue (Philips PAL I)" },
189 { 0x111a153b, BTTV_BOARD_TERRATVALUE, "Terratec TValue (Temic PAL I)" },
191 { 0x1123153b, BTTV_BOARD_TERRATVRADIO, "Terratec TV Radio+" },
192 { 0x1127153b, BTTV_BOARD_TERRATV, "Terratec TV+ (V1.05)" },
193 /* clashes with FlyVideo
194 *{ 0x18521852, BTTV_BOARD_TERRATV, "Terratec TV+ (V1.10)" }, */
195 { 0x1134153b, BTTV_BOARD_TERRATVALUE, "Terratec TValue (LR102)" },
196 { 0x1135153b, BTTV_BOARD_TERRATVALUER, "Terratec TValue Radio" }, /* LR102 */
197 { 0x5018153b, BTTV_BOARD_TERRATVALUE, "Terratec TValue" }, /* ?? */
198 { 0xff3b153b, BTTV_BOARD_TERRATVALUER, "Terratec TValue Radio" }, /* ?? */
200 { 0x400015b0, BTTV_BOARD_ZOLTRIX_GENIE, "Zoltrix Genie TV" },
201 { 0x400a15b0, BTTV_BOARD_ZOLTRIX_GENIE, "Zoltrix Genie TV" },
202 { 0x400d15b0, BTTV_BOARD_ZOLTRIX_GENIE, "Zoltrix Genie TV / Radio" },
203 { 0x401015b0, BTTV_BOARD_ZOLTRIX_GENIE, "Zoltrix Genie TV / Radio" },
204 { 0x401615b0, BTTV_BOARD_ZOLTRIX_GENIE, "Zoltrix Genie TV / Radio" },
206 { 0x1430aa00, BTTV_BOARD_PV143, "Provideo PV143A" },
207 { 0x1431aa00, BTTV_BOARD_PV143, "Provideo PV143B" },
208 { 0x1432aa00, BTTV_BOARD_PV143, "Provideo PV143C" },
209 { 0x1433aa00, BTTV_BOARD_PV143, "Provideo PV143D" },
210 { 0x1433aa03, BTTV_BOARD_PV143, "Security Eyes" },
212 { 0x1460aa00, BTTV_BOARD_PV150, "Provideo PV150A-1" },
213 { 0x1461aa01, BTTV_BOARD_PV150, "Provideo PV150A-2" },
214 { 0x1462aa02, BTTV_BOARD_PV150, "Provideo PV150A-3" },
215 { 0x1463aa03, BTTV_BOARD_PV150, "Provideo PV150A-4" },
217 { 0x1464aa04, BTTV_BOARD_PV150, "Provideo PV150B-1" },
218 { 0x1465aa05, BTTV_BOARD_PV150, "Provideo PV150B-2" },
219 { 0x1466aa06, BTTV_BOARD_PV150, "Provideo PV150B-3" },
220 { 0x1467aa07, BTTV_BOARD_PV150, "Provideo PV150B-4" },
222 { 0xa132ff00, BTTV_BOARD_IVC100, "IVC-100" },
223 { 0xa1550000, BTTV_BOARD_IVC200, "IVC-200" },
224 { 0xa1550001, BTTV_BOARD_IVC200, "IVC-200" },
225 { 0xa1550002, BTTV_BOARD_IVC200, "IVC-200" },
226 { 0xa1550003, BTTV_BOARD_IVC200, "IVC-200" },
227 { 0xa1550100, BTTV_BOARD_IVC200, "IVC-200G" },
228 { 0xa1550101, BTTV_BOARD_IVC200, "IVC-200G" },
229 { 0xa1550102, BTTV_BOARD_IVC200, "IVC-200G" },
230 { 0xa1550103, BTTV_BOARD_IVC200, "IVC-200G" },
231 { 0xa182ff00, BTTV_BOARD_IVC120, "IVC-120G" },
232 { 0xa182ff01, BTTV_BOARD_IVC120, "IVC-120G" },
233 { 0xa182ff02, BTTV_BOARD_IVC120, "IVC-120G" },
234 { 0xa182ff03, BTTV_BOARD_IVC120, "IVC-120G" },
235 { 0xa182ff04, BTTV_BOARD_IVC120, "IVC-120G" },
236 { 0xa182ff05, BTTV_BOARD_IVC120, "IVC-120G" },
237 { 0xa182ff06, BTTV_BOARD_IVC120, "IVC-120G" },
238 { 0xa182ff07, BTTV_BOARD_IVC120, "IVC-120G" },
239 { 0xa182ff08, BTTV_BOARD_IVC120, "IVC-120G" },
240 { 0xa182ff09, BTTV_BOARD_IVC120, "IVC-120G" },
241 { 0xa182ff0a, BTTV_BOARD_IVC120, "IVC-120G" },
242 { 0xa182ff0b, BTTV_BOARD_IVC120, "IVC-120G" },
243 { 0xa182ff0c, BTTV_BOARD_IVC120, "IVC-120G" },
244 { 0xa182ff0d, BTTV_BOARD_IVC120, "IVC-120G" },
245 { 0xa182ff0e, BTTV_BOARD_IVC120, "IVC-120G" },
246 { 0xa182ff0f, BTTV_BOARD_IVC120, "IVC-120G" },
248 { 0x41424344, BTTV_BOARD_GRANDTEC, "GrandTec Multi Capture" },
249 { 0x01020304, BTTV_BOARD_XGUARD, "Grandtec Grand X-Guard" },
251 { 0x18501851, BTTV_BOARD_CHRONOS_VS2, "FlyVideo 98 (LR50)/ Chronos Video Shuttle II" },
252 { 0xa0501851, BTTV_BOARD_CHRONOS_VS2, "FlyVideo 98 (LR50)/ Chronos Video Shuttle II" },
253 { 0x18511851, BTTV_BOARD_FLYVIDEO98EZ, "FlyVideo 98EZ (LR51)/ CyberMail AV" },
254 { 0x18521852, BTTV_BOARD_TYPHOON_TVIEW, "FlyVideo 98FM (LR50)/ Typhoon TView TV/FM Tuner" },
255 { 0x41a0a051, BTTV_BOARD_FLYVIDEO_98FM, "Lifeview FlyVideo 98 LR50 Rev Q" },
256 { 0x18501f7f, BTTV_BOARD_FLYVIDEO_98, "Lifeview Flyvideo 98" },
258 { 0x010115cb, BTTV_BOARD_GMV1, "AG GMV1" },
259 { 0x010114c7, BTTV_BOARD_MODTEC_205, "Modular Technology MM201/MM202/MM205/MM210/MM215 PCTV" },
261 { 0x10b42636, BTTV_BOARD_HAUPPAUGE878, "STB ???" },
262 { 0x217d6606, BTTV_BOARD_WINFAST2000, "Leadtek WinFast TV 2000" },
263 { 0xfff6f6ff, BTTV_BOARD_WINFAST2000, "Leadtek WinFast TV 2000" },
264 { 0x03116000, BTTV_BOARD_SENSORAY311, "Sensoray 311" },
265 { 0x00790e11, BTTV_BOARD_WINDVR, "Canopus WinDVR PCI" },
266 { 0xa0fca1a0, BTTV_BOARD_ZOLTRIX, "Face to Face Tvmax" },
267 { 0x82b2aa6a, BTTV_BOARD_SIMUS_GVC1100, "SIMUS GVC1100" },
268 { 0x146caa0c, BTTV_BOARD_PV951, "ituner spectra8" },
269 { 0x200a1295, BTTV_BOARD_PXC200, "ImageNation PXC200A" },
271 { 0x40111554, BTTV_BOARD_PV_BT878P_9B, "Prolink Pixelview PV-BT" },
272 { 0x17de0a01, BTTV_BOARD_KWORLD, "Mecer TV/FM/Video Tuner" },
274 { 0x01051805, BTTV_BOARD_PICOLO_TETRA_CHIP, "Picolo Tetra Chip #1" },
275 { 0x01061805, BTTV_BOARD_PICOLO_TETRA_CHIP, "Picolo Tetra Chip #2" },
276 { 0x01071805, BTTV_BOARD_PICOLO_TETRA_CHIP, "Picolo Tetra Chip #3" },
277 { 0x01081805, BTTV_BOARD_PICOLO_TETRA_CHIP, "Picolo Tetra Chip #4" },
279 { 0x15409511, BTTV_BOARD_ACORP_Y878F, "Acorp Y878F" },
281 { 0x53534149, BTTV_BOARD_SSAI_SECURITY, "SSAI Security Video Interface" },
282 { 0x5353414a, BTTV_BOARD_SSAI_ULTRASOUND, "SSAI Ultrasound Video Interface" },
284 /* likely broken, vendor id doesn't match the other magic views ...
285 * { 0xa0fca04f, BTTV_BOARD_MAGICTVIEW063, "Guillemot Maxi TV Video 3" }, */
287 /* Duplicate PCI ID, reconfigure for this board during the eeprom read.
288 * { 0x13eb0070, BTTV_BOARD_HAUPPAUGE_IMPACTVCB, "Hauppauge ImpactVCB" }, */
290 /* DVB cards (using pci function .1 for mpeg data xfer) */
291 { 0x001c11bd, BTTV_BOARD_PINNACLESAT, "Pinnacle PCTV Sat" },
292 { 0x01010071, BTTV_BOARD_NEBULA_DIGITV, "Nebula Electronics DigiTV" },
293 { 0x20007063, BTTV_BOARD_PC_HDTV, "pcHDTV HD-2000 TV"},
294 { 0x002611bd, BTTV_BOARD_TWINHAN_DST, "Pinnacle PCTV SAT CI" },
295 { 0x00011822, BTTV_BOARD_TWINHAN_DST, "Twinhan VisionPlus DVB" },
296 { 0xfc00270f, BTTV_BOARD_TWINHAN_DST, "ChainTech digitop DST-1000 DVB-S" },
297 { 0x07711461, BTTV_BOARD_AVDVBT_771, "AVermedia AverTV DVB-T 771" },
298 { 0x07611461, BTTV_BOARD_AVDVBT_761, "AverMedia AverTV DVB-T 761" },
299 { 0xdb1018ac, BTTV_BOARD_DVICO_DVBT_LITE, "DViCO FusionHDTV DVB-T Lite" },
300 { 0xdb1118ac, BTTV_BOARD_DVICO_DVBT_LITE, "Ultraview DVB-T Lite" },
301 { 0xd50018ac, BTTV_BOARD_DVICO_FUSIONHDTV_5_LITE, "DViCO FusionHDTV 5 Lite" },
302 { 0x00261822, BTTV_BOARD_TWINHAN_DST, "DNTV Live! Mini "},
303 { 0xd200dbc0, BTTV_BOARD_DVICO_FUSIONHDTV_2, "DViCO FusionHDTV 2" },
308 /* ----------------------------------------------------------------------- */
309 /* array with description for bt848 / bt878 tv/grabber cards */
311 struct tvcard bttv_tvcards[] = {
312 /* ---- card 0x00 ---------------------------------- */
313 [BTTV_BOARD_UNKNOWN] = {
314 .name = " *** UNKNOWN/GENERIC *** ",
319 .muxsel = { 2, 3, 1, 0 },
321 .tuner_addr = ADDR_UNSET,
322 .radio_addr = ADDR_UNSET,
324 [BTTV_BOARD_MIRO] = {
331 .muxsel = { 2, 3, 1, 1 },
332 .gpiomux = { 2, 0, 0, 0 },
336 .tuner_addr = ADDR_UNSET,
337 .radio_addr = ADDR_UNSET,
339 [BTTV_BOARD_HAUPPAUGE] = {
340 .name = "Hauppauge (bt848)",
346 .muxsel = { 2, 3, 1, 1 },
347 .gpiomux = { 0, 1, 2, 3 },
351 .tuner_addr = ADDR_UNSET,
352 .radio_addr = ADDR_UNSET,
355 .name = "STB, Gateway P/N 6000699 (bt848)",
361 .muxsel = { 2, 3, 1, 1 },
362 .gpiomux = { 4, 0, 2, 3 },
366 .tuner_type = TUNER_PHILIPS_NTSC,
367 .tuner_addr = ADDR_UNSET,
368 .radio_addr = ADDR_UNSET,
373 /* ---- card 0x04 ---------------------------------- */
374 [BTTV_BOARD_INTEL] = {
375 .name = "Intel Create and Share PCI/ Smart Video Recorder III",
381 .muxsel = { 2, 3, 1, 1 },
384 .tuner_type = TUNER_ABSENT,
385 .tuner_addr = ADDR_UNSET,
386 .radio_addr = ADDR_UNSET,
388 [BTTV_BOARD_DIAMOND] = {
389 .name = "Diamond DTV2000",
395 .muxsel = { 2, 3, 1, 0 },
396 .gpiomux = { 0, 1, 0, 1 },
400 .tuner_addr = ADDR_UNSET,
401 .radio_addr = ADDR_UNSET,
403 [BTTV_BOARD_AVERMEDIA] = {
404 .name = "AVerMedia TVPhone",
409 .muxsel = { 2, 3, 1, 1 },
411 .gpiomux = { 0x0c, 0x04, 0x08, 0x04 },
412 /* 0x04 for some cards ?? */
415 .tuner_addr = ADDR_UNSET,
416 .radio_addr = ADDR_UNSET,
417 .audio_mode_gpio= avermedia_tvphone_audio,
420 [BTTV_BOARD_MATRIX_VISION] = {
421 .name = "MATRIX-Vision MV-Delta",
427 .muxsel = { 2, 3, 1, 0, 0 },
431 .tuner_addr = ADDR_UNSET,
432 .radio_addr = ADDR_UNSET,
435 /* ---- card 0x08 ---------------------------------- */
436 [BTTV_BOARD_FLYVIDEO] = {
437 .name = "Lifeview FlyVideo II (Bt848) LR26 / MAXI TV Video PCI2 LR26",
443 .muxsel = { 2, 3, 1, 1 },
444 .gpiomux = { 0, 0xc00, 0x800, 0x400 },
449 .tuner_addr = ADDR_UNSET,
450 .radio_addr = ADDR_UNSET,
452 [BTTV_BOARD_TURBOTV] = {
453 .name = "IMS/IXmicro TurboTV",
459 .muxsel = { 2, 3, 1, 1 },
460 .gpiomux = { 1, 1, 2, 3 },
463 .tuner_type = TUNER_TEMIC_PAL,
464 .tuner_addr = ADDR_UNSET,
465 .radio_addr = ADDR_UNSET,
467 [BTTV_BOARD_HAUPPAUGE878] = {
468 .name = "Hauppauge (bt878)",
473 .gpiomask = 0x0f, /* old: 7 */
474 .muxsel = { 2, 0, 1, 1 },
475 .gpiomux = { 0, 1, 2, 3 },
480 .tuner_addr = ADDR_UNSET,
481 .radio_addr = ADDR_UNSET,
483 [BTTV_BOARD_MIROPRO] = {
484 .name = "MIRO PCTV pro",
490 .muxsel = { 2, 3, 1, 1 },
491 .gpiomux = { 0x20001,0x10001, 0, 0 },
495 .tuner_addr = ADDR_UNSET,
496 .radio_addr = ADDR_UNSET,
499 /* ---- card 0x0c ---------------------------------- */
500 [BTTV_BOARD_ADSTECH_TV] = {
501 .name = "ADS Technologies Channel Surfer TV (bt848)",
507 .muxsel = { 2, 3, 1, 1 },
508 .gpiomux = { 13, 14, 11, 7 },
511 .tuner_addr = ADDR_UNSET,
512 .radio_addr = ADDR_UNSET,
514 [BTTV_BOARD_AVERMEDIA98] = {
515 .name = "AVerMedia TVCapture 98",
521 .muxsel = { 2, 3, 1, 1 },
522 .gpiomux = { 13, 14, 11, 7 },
526 .tuner_type = TUNER_PHILIPS_PAL,
527 .tuner_addr = ADDR_UNSET,
528 .radio_addr = ADDR_UNSET,
529 .audio_mode_gpio= avermedia_tv_stereo_audio,
533 .name = "Aimslab Video Highway Xtreme (VHX)",
539 .muxsel = { 2, 3, 1, 1 },
540 .gpiomux = { 0, 2, 1, 3 }, /* old: {0, 1, 2, 3, 4} */
545 .tuner_addr = ADDR_UNSET,
546 .radio_addr = ADDR_UNSET,
548 [BTTV_BOARD_ZOLTRIX] = {
549 .name = "Zoltrix TV-Max",
555 .muxsel = { 2, 3, 1, 1 },
556 .gpiomux = { 0, 0, 1, 0 },
560 .tuner_addr = ADDR_UNSET,
561 .radio_addr = ADDR_UNSET,
564 /* ---- card 0x10 ---------------------------------- */
565 [BTTV_BOARD_PIXVIEWPLAYTV] = {
566 .name = "Prolink Pixelview PlayTV (bt878)",
571 .gpiomask = 0x01fe00,
572 .muxsel = { 2, 3, 1, 1 },
573 /* 2003-10-20 by "Anton A. Arapov" <arapov@mail.ru> */
574 .gpiomux = { 0x001e00, 0, 0x018000, 0x014000 },
575 .gpiomute = 0x002000,
580 [BTTV_BOARD_WINVIEW_601] = {
581 .name = "Leadtek WinView 601",
586 .gpiomask = 0x8300f8,
587 .muxsel = { 2, 3, 1, 1,0 },
588 .gpiomux = { 0x4fa007,0xcfa007,0xcfa007,0xcfa007 },
589 .gpiomute = 0xcfa007,
592 .tuner_addr = ADDR_UNSET,
593 .radio_addr = ADDR_UNSET,
594 .volume_gpio = winview_volume,
597 [BTTV_BOARD_AVEC_INTERCAP] = {
598 .name = "AVEC Intercapture",
604 .muxsel = { 2, 3, 1, 1 },
605 .gpiomux = { 1, 0, 0, 0 },
608 .tuner_addr = ADDR_UNSET,
609 .radio_addr = ADDR_UNSET,
611 [BTTV_BOARD_LIFE_FLYKIT] = {
612 .name = "Lifeview FlyVideo II EZ /FlyKit LR38 Bt848 (capture only)",
617 .gpiomask = 0x8dff00,
618 .muxsel = { 2, 3, 1, 1 },
622 .tuner_addr = ADDR_UNSET,
623 .radio_addr = ADDR_UNSET,
626 /* ---- card 0x14 ---------------------------------- */
627 [BTTV_BOARD_CEI_RAFFLES] = {
628 .name = "CEI Raffles Card",
633 .muxsel = { 2, 3, 1, 1 },
635 .tuner_addr = ADDR_UNSET,
636 .radio_addr = ADDR_UNSET,
638 [BTTV_BOARD_CONFERENCETV] = {
639 .name = "Lifeview FlyVideo 98/ Lucky Star Image World ConferenceTV LR50",
641 .audio_inputs = 2, /* tuner, line in */
645 .muxsel = { 2, 3, 1, 1 },
646 .gpiomux = { 0, 0x800, 0x1000, 0x1000 },
649 .tuner_type = TUNER_PHILIPS_PAL_I,
650 .tuner_addr = ADDR_UNSET,
651 .radio_addr = ADDR_UNSET,
653 [BTTV_BOARD_PHOEBE_TVMAS] = {
654 .name = "Askey CPH050/ Phoebe Tv Master + FM",
660 .muxsel = { 2, 3, 1, 1 },
661 .gpiomux = { 0, 1, 0x800, 0x400 },
666 .tuner_addr = ADDR_UNSET,
667 .radio_addr = ADDR_UNSET,
669 [BTTV_BOARD_MODTEC_205] = {
670 .name = "Modular Technology MM201/MM202/MM205/MM210/MM215 PCTV, bt878",
676 .muxsel = { 2, 3, -1 },
677 .digital_mode = DIGITAL_MODE_CAMERA,
678 .gpiomux = { 0, 0, 0, 0 },
681 .tuner_type = TUNER_ALPS_TSBB5_PAL_I,
682 .tuner_addr = ADDR_UNSET,
683 .radio_addr = ADDR_UNSET,
686 /* ---- card 0x18 ---------------------------------- */
687 [BTTV_BOARD_MAGICTVIEW061] = {
688 .name = "Askey CPH05X/06X (bt878) [many vendors]",
694 .muxsel = { 2, 3, 1, 1 },
695 .gpiomux = {0x400, 0x400, 0x400, 0x400 },
700 .tuner_addr = ADDR_UNSET,
701 .radio_addr = ADDR_UNSET,
704 [BTTV_BOARD_VOBIS_BOOSTAR] = {
705 .name = "Terratec TerraTV+ Version 1.0 (Bt848)/ Terra TValue Version 1.0/ Vobis TV-Boostar",
710 .gpiomask = 0x1f0fff,
711 .muxsel = { 2, 3, 1, 1 },
712 .gpiomux = { 0x20000, 0x30000, 0x10000, 0 },
715 .tuner_type = TUNER_PHILIPS_PAL,
716 .tuner_addr = ADDR_UNSET,
717 .radio_addr = ADDR_UNSET,
718 .audio_mode_gpio= terratv_audio,
720 [BTTV_BOARD_HAUPPAUG_WCAM] = {
721 .name = "Hauppauge WinCam newer (bt878)",
727 .muxsel = { 2, 0, 1, 1 },
728 .gpiomux = { 0, 1, 2, 3 },
732 .tuner_addr = ADDR_UNSET,
733 .radio_addr = ADDR_UNSET,
735 [BTTV_BOARD_MAXI] = {
736 .name = "Lifeview FlyVideo 98/ MAXI TV Video PCI2 LR50",
742 .muxsel = { 2, 3, 1, 1 },
743 .gpiomux = { 0, 0x800, 0x1000, 0x1000 },
746 .tuner_type = TUNER_PHILIPS_SECAM,
747 .tuner_addr = ADDR_UNSET,
748 .radio_addr = ADDR_UNSET,
751 /* ---- card 0x1c ---------------------------------- */
752 [BTTV_BOARD_TERRATV] = {
753 .name = "Terratec TerraTV+ Version 1.1 (bt878)",
758 .gpiomask = 0x1f0fff,
759 .muxsel = { 2, 3, 1, 1 },
760 .gpiomux = { 0x20000, 0x30000, 0x10000, 0x00000 },
763 .tuner_type = TUNER_PHILIPS_PAL,
764 .tuner_addr = ADDR_UNSET,
765 .radio_addr = ADDR_UNSET,
766 .audio_mode_gpio= terratv_audio,
768 External 20 pin connector (for Active Radio Upgrade board)
774 gpio05: om5610-stereo
778 gpio09+10: nIOR, nSEL ?? (bt878)
782 gpio16: u2-A0 (1st 4052bt)
785 gpio19: u4-A0 (2nd 4052)
789 00000 : Cdrom (internal audio input)
790 10000 : ext. Video audio input
799 [BTTV_BOARD_PXC200] = {
800 /* Jannik Fritsch <jannik@techfak.uni-bielefeld.de> */
801 .name = "Imagenation PXC200",
805 .svhs = 1, /* was: 4 */
807 .muxsel = { 2, 3, 1, 0, 0},
811 .tuner_addr = ADDR_UNSET,
812 .radio_addr = ADDR_UNSET,
813 .muxsel_hook = PXC200_muxsel,
816 [BTTV_BOARD_FLYVIDEO_98] = {
817 .name = "Lifeview FlyVideo 98 LR50",
822 .gpiomask = 0x1800, /* 0x8dfe00 */
823 .muxsel = { 2, 3, 1, 1 },
824 .gpiomux = { 0, 0x0800, 0x1000, 0x1000 },
828 .tuner_addr = ADDR_UNSET,
829 .radio_addr = ADDR_UNSET,
831 [BTTV_BOARD_IPROTV] = {
832 .name = "Formac iProTV, Formac ProTV I (bt848)",
838 .muxsel = { 2, 3, 1, 1 },
839 .gpiomux = { 1, 0, 0, 0 },
841 .tuner_type = TUNER_PHILIPS_PAL,
842 .tuner_addr = ADDR_UNSET,
843 .radio_addr = ADDR_UNSET,
846 /* ---- card 0x20 ---------------------------------- */
847 [BTTV_BOARD_INTEL_C_S_PCI] = {
848 .name = "Intel Create and Share PCI/ Smart Video Recorder III",
854 .muxsel = { 2, 3, 1, 1 },
857 .tuner_type = TUNER_ABSENT,
858 .tuner_addr = ADDR_UNSET,
859 .radio_addr = ADDR_UNSET,
861 [BTTV_BOARD_TERRATVALUE] = {
862 .name = "Terratec TerraTValue Version Bt878",
867 .gpiomask = 0xffff00,
868 .muxsel = { 2, 3, 1, 1 },
869 .gpiomux = { 0x500, 0, 0x300, 0x900 },
873 .tuner_type = TUNER_PHILIPS_PAL,
874 .tuner_addr = ADDR_UNSET,
875 .radio_addr = ADDR_UNSET,
877 [BTTV_BOARD_WINFAST2000] = {
878 .name = "Leadtek WinFast 2000/ WinFast 2000 XP",
883 .muxsel = { 2, 3, 1, 1, 0 }, /* TV, CVid, SVid, CVid over SVid connector */
884 /* Alexander Varakin <avarakin@hotmail.com> [stereo version] */
885 .gpiomask = 0xb33000,
886 .gpiomux = { 0x122000,0x1000,0x0000,0x620000 },
887 .gpiomute = 0x800000,
888 /* Audio Routing for "WinFast 2000 XP" (no tv stereo !)
889 gpio23 -- hef4052:nEnable (0x800000)
892 0x0000: external audio
896 Note: There exists another variant "Winfast 2000" with tv stereo !?
897 Note: eeprom only contains FF and pci subsystem id 107d:6606
902 .tuner_type = TUNER_PHILIPS_PAL, /* default for now, gpio reads BFFF06 for Pal bg+dk */
903 .tuner_addr = ADDR_UNSET,
904 .radio_addr = ADDR_UNSET,
905 .audio_mode_gpio= winfast2000_audio,
908 [BTTV_BOARD_CHRONOS_VS2] = {
909 .name = "Lifeview FlyVideo 98 LR50 / Chronos Video Shuttle II",
915 .muxsel = { 2, 3, 1, 1 },
916 .gpiomux = { 0, 0x800, 0x1000, 0x1000 },
920 .tuner_addr = ADDR_UNSET,
921 .radio_addr = ADDR_UNSET,
924 /* ---- card 0x24 ---------------------------------- */
925 [BTTV_BOARD_TYPHOON_TVIEW] = {
926 .name = "Lifeview FlyVideo 98FM LR50 / Typhoon TView TV/FM Tuner",
932 .muxsel = { 2, 3, 1, 1 },
933 .gpiomux = { 0, 0x800, 0x1000, 0x1000 },
937 .tuner_addr = ADDR_UNSET,
938 .radio_addr = ADDR_UNSET,
941 [BTTV_BOARD_PXELVWPLTVPRO] = {
942 .name = "Prolink PixelView PlayTV pro",
948 .muxsel = { 2, 3, 1, 1 },
949 .gpiomux = { 0x21, 0x20, 0x24, 0x2c },
954 .tuner_addr = ADDR_UNSET,
955 .radio_addr = ADDR_UNSET,
957 [BTTV_BOARD_MAGICTVIEW063] = {
958 .name = "Askey CPH06X TView99",
963 .gpiomask = 0x551e00,
964 .muxsel = { 2, 3, 1, 0 },
965 .gpiomux = { 0x551400, 0x551200, 0, 0 },
966 .gpiomute = 0x551c00,
969 .tuner_type = TUNER_PHILIPS_PAL_I,
970 .tuner_addr = ADDR_UNSET,
971 .radio_addr = ADDR_UNSET,
974 [BTTV_BOARD_PINNACLE] = {
975 .name = "Pinnacle PCTV Studio/Rave",
980 .gpiomask = 0x03000F,
981 .muxsel = { 2, 3, 1, 1 },
982 .gpiomux = { 2, 0xd0001, 0, 0 },
987 .tuner_addr = ADDR_UNSET,
988 .radio_addr = ADDR_UNSET,
991 /* ---- card 0x28 ---------------------------------- */
992 [BTTV_BOARD_STB2] = {
993 .name = "STB TV PCI FM, Gateway P/N 6000704 (bt878), 3Dfx VoodooTV 100",
999 .muxsel = { 2, 3, 1, 1 },
1000 .gpiomux = { 4, 0, 2, 3 },
1004 .tuner_type = TUNER_PHILIPS_NTSC,
1005 .tuner_addr = ADDR_UNSET,
1006 .radio_addr = ADDR_UNSET,
1010 [BTTV_BOARD_AVPHONE98] = {
1011 .name = "AVerMedia TVPhone 98",
1017 .muxsel = { 2, 3, 1, 1 },
1018 .gpiomux = { 13, 4, 11, 7 },
1021 .tuner_type = UNSET,
1022 .tuner_addr = ADDR_UNSET,
1023 .radio_addr = ADDR_UNSET,
1025 .audio_mode_gpio= avermedia_tvphone_audio,
1027 [BTTV_BOARD_PV951] = {
1028 .name = "ProVideo PV951", /* pic16c54 */
1034 .muxsel = { 2, 3, 1, 1},
1035 .gpiomux = { 0, 0, 0, 0},
1039 .tuner_type = TUNER_PHILIPS_PAL_I,
1040 .tuner_addr = ADDR_UNSET,
1041 .radio_addr = ADDR_UNSET,
1043 [BTTV_BOARD_ONAIR_TV] = {
1044 .name = "Little OnAir TV",
1050 .muxsel = { 2, 3, 1, 1 },
1051 .gpiomux = { 0xff9ff6, 0xff9ff6, 0xff1ff7, 0 },
1052 .gpiomute = 0xff3ffc,
1054 .tuner_type = UNSET,
1055 .tuner_addr = ADDR_UNSET,
1056 .radio_addr = ADDR_UNSET,
1059 /* ---- card 0x2c ---------------------------------- */
1060 [BTTV_BOARD_SIGMA_TVII_FM] = {
1061 .name = "Sigma TVII-FM",
1067 .muxsel = { 2, 3, 1, 1 },
1068 .gpiomux = { 1, 1, 0, 2 },
1072 .tuner_type = UNSET,
1073 .tuner_addr = ADDR_UNSET,
1074 .radio_addr = ADDR_UNSET,
1076 [BTTV_BOARD_MATRIX_VISION2] = {
1077 .name = "MATRIX-Vision MV-Delta 2",
1083 .muxsel = { 2, 3, 1, 0, 0 },
1087 .tuner_type = UNSET,
1088 .tuner_addr = ADDR_UNSET,
1089 .radio_addr = ADDR_UNSET,
1091 [BTTV_BOARD_ZOLTRIX_GENIE] = {
1092 .name = "Zoltrix Genie TV/FM",
1097 .gpiomask = 0xbcf03f,
1098 .muxsel = { 2, 3, 1, 1 },
1099 .gpiomux = { 0xbc803f, 0xbc903f, 0xbcb03f, 0 },
1100 .gpiomute = 0xbcb03f,
1103 .tuner_type = TUNER_TEMIC_4039FR5_NTSC,
1104 .tuner_addr = ADDR_UNSET,
1105 .radio_addr = ADDR_UNSET,
1107 [BTTV_BOARD_TERRATVRADIO] = {
1108 .name = "Terratec TV/Radio+",
1113 .gpiomask = 0x70000,
1114 .muxsel = { 2, 3, 1, 1 },
1115 .gpiomux = { 0x20000, 0x30000, 0x10000, 0 },
1116 .gpiomute = 0x40000,
1120 .tuner_type = TUNER_PHILIPS_PAL_I,
1121 .tuner_addr = ADDR_UNSET,
1122 .radio_addr = ADDR_UNSET,
1126 /* ---- card 0x30 ---------------------------------- */
1127 [BTTV_BOARD_DYNALINK] = {
1128 .name = "Askey CPH03x/ Dynalink Magic TView",
1134 .muxsel = { 2, 3, 1, 1 },
1135 .gpiomux = {2,0,0,0 },
1139 .tuner_type = UNSET,
1140 .tuner_addr = ADDR_UNSET,
1141 .radio_addr = ADDR_UNSET,
1143 [BTTV_BOARD_GVBCTV3PCI] = {
1144 .name = "IODATA GV-BCTV3/PCI",
1149 .gpiomask = 0x010f00,
1150 .muxsel = {2, 3, 0, 0 },
1151 .gpiomux = {0x10000, 0, 0x10000, 0 },
1154 .tuner_type = TUNER_ALPS_TSHC6_NTSC,
1155 .tuner_addr = ADDR_UNSET,
1156 .radio_addr = ADDR_UNSET,
1157 .audio_mode_gpio= gvbctv3pci_audio,
1159 [BTTV_BOARD_PXELVWPLTVPAK] = {
1160 .name = "Prolink PV-BT878P+4E / PixelView PlayTV PAK / Lenco MXTV-9578 CP",
1165 .gpiomask = 0xAA0000,
1166 .muxsel = { 2,3,1,1,-1 },
1167 .digital_mode = DIGITAL_MODE_CAMERA,
1168 .gpiomux = { 0x20000, 0, 0x80000, 0x80000 },
1169 .gpiomute = 0xa8000,
1172 .tuner_type = TUNER_PHILIPS_PAL_I,
1173 .tuner_addr = ADDR_UNSET,
1174 .radio_addr = ADDR_UNSET,
1176 /* GPIO wiring: (different from Rev.4C !)
1177 GPIO17: U4.A0 (first hef4052bt)
1179 GPIO20: U5.A1 (second hef4052bt)
1181 GPIO22: BT832 Reset Line
1182 GPIO23: A5,A0, U5,nEN
1183 Note: At i2c=0x8a is a Bt832 chip, which changes to 0x88 after being reset via GPIO22
1186 [BTTV_BOARD_EAGLE] = {
1187 .name = "Eagle Wireless Capricorn2 (bt878A)",
1193 .muxsel = { 2, 0, 1, 1 },
1194 .gpiomux = { 0, 1, 2, 3 },
1197 .tuner_type = UNSET /* TUNER_ALPS_TMDH2_NTSC */,
1198 .tuner_addr = ADDR_UNSET,
1199 .radio_addr = ADDR_UNSET,
1202 /* ---- card 0x34 ---------------------------------- */
1203 [BTTV_BOARD_PINNACLEPRO] = {
1204 /* David Härdeman <david@2gen.com> */
1205 .name = "Pinnacle PCTV Studio Pro",
1210 .gpiomask = 0x03000F,
1211 .muxsel = { 2, 3, 1, 1 },
1212 .gpiomux = { 1, 0xd0001, 0, 0 },
1214 /* sound path (5 sources):
1215 MUX1 (mask 0x03), Enable Pin 0x08 (0=enable, 1=disable)
1218 2= Mono TV sound from Tuner
1220 MUX2 (mask 0x30000):
1222 1= FM stereo Radio from Tuner */
1225 .tuner_type = UNSET,
1226 .tuner_addr = ADDR_UNSET,
1227 .radio_addr = ADDR_UNSET,
1229 [BTTV_BOARD_TVIEW_RDS_FM] = {
1230 /* Claas Langbehn <claas@bigfoot.com>,
1231 Sven Grothklags <sven@upb.de> */
1232 .name = "Typhoon TView RDS + FM Stereo / KNC1 TV Station RDS",
1238 .muxsel = { 2, 3, 1, 1 },
1239 .gpiomux = { 0, 0, 0x10, 8 },
1243 .tuner_type = TUNER_PHILIPS_PAL,
1244 .tuner_addr = ADDR_UNSET,
1245 .radio_addr = ADDR_UNSET,
1248 [BTTV_BOARD_LIFETEC_9415] = {
1249 /* Tim Röstermundt <rosterm@uni-muenster.de>
1250 in de.comp.os.unix.linux.hardware:
1251 options bttv card=0 pll=1 radio=1 gpiomask=0x18e0
1252 gpiomux =0x44c71f,0x44d71f,0,0x44d71f,0x44dfff
1253 options tuner type=5 */
1254 .name = "Lifeview FlyVideo 2000 /FlyVideo A2/ Lifetec LT 9415 TV [LR90]",
1260 .muxsel = { 2, 3, 1, 1 },
1261 .gpiomux = { 0x0000,0x0800,0x1000,0x1000 },
1263 /* For cards with tda9820/tda9821:
1264 0x0000: Tuner normal stereo
1265 0x0080: Tuner A2 SAP (second audio program = Zweikanalton)
1266 0x0880: Tuner A2 stereo */
1268 .tuner_type = UNSET,
1269 .tuner_addr = ADDR_UNSET,
1270 .radio_addr = ADDR_UNSET,
1272 [BTTV_BOARD_BESTBUY_EASYTV] = {
1273 /* Miguel Angel Alvarez <maacruz@navegalia.com>
1274 old Easy TV BT848 version (model CPH031) */
1275 .name = "Askey CPH031/ BESTBUY Easy TV",
1281 .muxsel = { 2, 3, 1, 0 },
1282 .gpiomux = { 2, 0, 0, 0 },
1286 .tuner_type = TUNER_TEMIC_PAL,
1287 .tuner_addr = ADDR_UNSET,
1288 .radio_addr = ADDR_UNSET,
1291 /* ---- card 0x38 ---------------------------------- */
1292 [BTTV_BOARD_FLYVIDEO_98FM] = {
1293 /* Gordon Heydon <gjheydon@bigfoot.com ('98) */
1294 .name = "Lifeview FlyVideo 98FM LR50",
1300 .muxsel = { 2, 3, 1, 1 },
1301 .gpiomux = { 0, 0x800, 0x1000, 0x1000 },
1304 .tuner_type = TUNER_PHILIPS_PAL,
1305 .tuner_addr = ADDR_UNSET,
1306 .radio_addr = ADDR_UNSET,
1308 /* This is the ultimate cheapo capture card
1309 * just a BT848A on a small PCB!
1310 * Steve Hosgood <steve@equiinet.com> */
1311 [BTTV_BOARD_GRANDTEC] = {
1312 .name = "GrandTec 'Grand Video Capture' (Bt848)",
1323 .tuner_type = UNSET,
1324 .tuner_addr = ADDR_UNSET,
1325 .radio_addr = ADDR_UNSET,
1327 [BTTV_BOARD_ASKEY_CPH060] = {
1328 /* Daniel Herrington <daniel.herrington@home.com> */
1329 .name = "Askey CPH060/ Phoebe TV Master Only (No FM)",
1335 .muxsel = { 2, 3, 1, 1},
1336 .gpiomux = { 0x400, 0x400, 0x400, 0x400 },
1340 .tuner_type = TUNER_TEMIC_4036FY5_NTSC,
1341 .tuner_addr = ADDR_UNSET,
1342 .radio_addr = ADDR_UNSET,
1344 [BTTV_BOARD_ASKEY_CPH03X] = {
1345 /* Matti Mottus <mottus@physic.ut.ee> */
1346 .name = "Askey CPH03x TV Capturer",
1351 .gpiomask = 0x03000F,
1352 .muxsel = { 2, 3, 1, 0 },
1353 .gpiomux = { 2, 0, 0, 0 },
1356 .tuner_type = TUNER_TEMIC_PAL,
1357 .tuner_addr = ADDR_UNSET,
1358 .radio_addr = ADDR_UNSET,
1361 /* ---- card 0x3c ---------------------------------- */
1362 [BTTV_BOARD_MM100PCTV] = {
1363 /* Philip Blundell <philb@gnu.org> */
1364 .name = "Modular Technology MM100PCTV",
1370 .muxsel = { 2, 3, 1, 1 },
1371 .gpiomux = { 2, 0, 0, 1 },
1374 .tuner_type = TUNER_TEMIC_PAL,
1375 .tuner_addr = ADDR_UNSET,
1376 .radio_addr = ADDR_UNSET,
1378 [BTTV_BOARD_GMV1] = {
1379 /* Adrian Cox <adrian@humboldt.co.uk */
1380 .name = "AG Electronics GMV1",
1391 .tuner_type = UNSET,
1392 .tuner_addr = ADDR_UNSET,
1393 .radio_addr = ADDR_UNSET,
1395 [BTTV_BOARD_BESTBUY_EASYTV2] = {
1396 /* Miguel Angel Alvarez <maacruz@navegalia.com>
1397 new Easy TV BT878 version (model CPH061)
1398 special thanks to Informatica Mieres for providing the card */
1399 .name = "Askey CPH061/ BESTBUY Easy TV (bt878)",
1405 .muxsel = { 2, 3, 1, 0 },
1406 .gpiomux = { 1, 0, 4, 4 },
1410 .tuner_type = TUNER_PHILIPS_PAL,
1411 .tuner_addr = ADDR_UNSET,
1412 .radio_addr = ADDR_UNSET,
1414 [BTTV_BOARD_ATI_TVWONDER] = {
1415 /* Lukas Gebauer <geby@volny.cz> */
1416 .name = "ATI TV-Wonder",
1422 .muxsel = { 2, 3, 1, 0 },
1423 .gpiomux = { 0xbffe, 0, 0xbfff, 0 },
1426 .tuner_type = TUNER_TEMIC_4006FN5_MULTI_PAL,
1427 .tuner_addr = ADDR_UNSET,
1428 .radio_addr = ADDR_UNSET,
1431 /* ---- card 0x40 ---------------------------------- */
1432 [BTTV_BOARD_ATI_TVWONDERVE] = {
1433 /* Lukas Gebauer <geby@volny.cz> */
1434 .name = "ATI TV-Wonder VE",
1440 .muxsel = { 2, 3, 0, 1 },
1441 .gpiomux = { 0, 0, 1, 0 },
1444 .tuner_type = TUNER_TEMIC_4006FN5_MULTI_PAL,
1445 .tuner_addr = ADDR_UNSET,
1446 .radio_addr = ADDR_UNSET,
1448 [BTTV_BOARD_FLYVIDEO2000] = {
1449 /* DeeJay <deejay@westel900.net (2000S) */
1450 .name = "Lifeview FlyVideo 2000S LR90",
1456 .muxsel = { 2, 3, 0, 1 },
1457 /* Radio changed from 1e80 to 0x800 to make
1458 FlyVideo2000S in .hu happy (gm)*/
1459 /* -dk-???: set mute=0x1800 for tda9874h daughterboard */
1460 .gpiomux = { 0x0000,0x0800,0x1000,0x1000 },
1462 .audio_mode_gpio= fv2000s_audio,
1467 .tuner_type = TUNER_PHILIPS_PAL,
1468 .tuner_addr = ADDR_UNSET,
1469 .radio_addr = ADDR_UNSET,
1471 [BTTV_BOARD_TERRATVALUER] = {
1472 .name = "Terratec TValueRadio",
1477 .gpiomask = 0xffff00,
1478 .muxsel = { 2, 3, 1, 1 },
1479 .gpiomux = { 0x500, 0x500, 0x300, 0x900 },
1483 .tuner_type = TUNER_PHILIPS_PAL,
1484 .tuner_addr = ADDR_UNSET,
1485 .radio_addr = ADDR_UNSET,
1488 [BTTV_BOARD_GVBCTV4PCI] = {
1489 /* TANAKA Kei <peg00625@nifty.com> */
1490 .name = "IODATA GV-BCTV4/PCI",
1495 .gpiomask = 0x010f00,
1496 .muxsel = {2, 3, 0, 0 },
1497 .gpiomux = {0x10000, 0, 0x10000, 0 },
1500 .tuner_type = TUNER_SHARP_2U5JF5540_NTSC,
1501 .tuner_addr = ADDR_UNSET,
1502 .radio_addr = ADDR_UNSET,
1503 .audio_mode_gpio= gvbctv3pci_audio,
1506 /* ---- card 0x44 ---------------------------------- */
1507 [BTTV_BOARD_VOODOOTV_FM] = {
1508 .name = "3Dfx VoodooTV FM (Euro)",
1509 /* try "insmod msp3400 simple=0" if you have
1510 * sound problems with this card. */
1515 .gpiomask = 0x4f8a00,
1516 /* 0x100000: 1=MSP enabled (0=disable again)
1517 * 0x010000: Connected to "S0" on tda9880 (0=Pal/BG, 1=NTSC) */
1518 .gpiomux = {0x947fff, 0x987fff,0x947fff,0x947fff },
1519 .gpiomute = 0x947fff,
1520 /* tvtuner, radio, external,internal, mute, stereo
1521 * tuner, Composit, SVid, Composit-on-Svid-adapter */
1522 .muxsel = { 2, 3 ,0 ,1 },
1523 .tuner_type = TUNER_MT2032,
1524 .tuner_addr = ADDR_UNSET,
1525 .radio_addr = ADDR_UNSET,
1529 [BTTV_BOARD_VOODOOTV_200] = {
1530 .name = "VoodooTV 200 (USA)",
1531 /* try "insmod msp3400 simple=0" if you have
1532 * sound problems with this card. */
1537 .gpiomask = 0x4f8a00,
1538 /* 0x100000: 1=MSP enabled (0=disable again)
1539 * 0x010000: Connected to "S0" on tda9880 (0=Pal/BG, 1=NTSC) */
1540 .gpiomux = {0x947fff, 0x987fff,0x947fff,0x947fff },
1541 .gpiomute = 0x947fff,
1542 /* tvtuner, radio, external,internal, mute, stereo
1543 * tuner, Composit, SVid, Composit-on-Svid-adapter */
1544 .muxsel = { 2, 3 ,0 ,1 },
1545 .tuner_type = TUNER_MT2032,
1546 .tuner_addr = ADDR_UNSET,
1547 .radio_addr = ADDR_UNSET,
1551 [BTTV_BOARD_AIMMS] = {
1552 /* Philip Blundell <pb@nexus.co.uk> */
1553 .name = "Active Imaging AIMMS",
1557 .tuner_type = UNSET,
1558 .tuner_addr = ADDR_UNSET,
1559 .radio_addr = ADDR_UNSET,
1564 [BTTV_BOARD_PV_BT878P_PLUS] = {
1565 /* Tomasz Pyra <hellfire@sedez.iq.pl> */
1566 .name = "Prolink Pixelview PV-BT878P+ (Rev.4C,8E)",
1572 .muxsel = { 2, 3, 1, 1 },
1573 .gpiomux = { 0, 0, 11, 7 }, /* TV and Radio with same GPIO ! */
1577 .tuner_type = TUNER_LG_PAL_I_FM,
1578 .tuner_addr = ADDR_UNSET,
1579 .radio_addr = ADDR_UNSET,
1582 GPIO0: U4.A0 (hef4052bt)
1584 GPIO2: U4.A1 (second hef4052bt)
1585 GPIO3: U4.nEN, U5.A0, A5.nEN
1589 [BTTV_BOARD_FLYVIDEO98EZ] = {
1590 .name = "Lifeview FlyVideo 98EZ (capture only) LR51",
1595 .muxsel = { 2, 3, 1, 1 }, /* AV1, AV2, SVHS, CVid adapter on SVHS */
1598 .tuner_type = UNSET,
1599 .tuner_addr = ADDR_UNSET,
1600 .radio_addr = ADDR_UNSET,
1603 /* ---- card 0x48 ---------------------------------- */
1604 [BTTV_BOARD_PV_BT878P_9B] = {
1605 /* Dariusz Kowalewski <darekk@automex.pl> */
1606 .name = "Prolink Pixelview PV-BT878P+9B (PlayTV Pro rev.9B FM+NICAM)",
1612 .muxsel = { 2, 3, 1, 1 },
1613 .gpiomux = { 0x01, 0x00, 0x03, 0x03 },
1619 .tuner_type = TUNER_PHILIPS_PAL,
1620 .tuner_addr = ADDR_UNSET,
1621 .radio_addr = ADDR_UNSET,
1622 .audio_mode_gpio= pvbt878p9b_audio, /* Note: not all cards have stereo */
1623 .has_radio = 1, /* Note: not all cards have radio */
1630 GPIO20,22,23: R30,R29,R28
1633 [BTTV_BOARD_SENSORAY311] = {
1634 /* Clay Kunz <ckunz@mail.arc.nasa.gov> */
1635 /* you must jumper JP5 for the card to work */
1636 .name = "Sensoray 311",
1642 .muxsel = { 2, 3, 1, 0, 0 },
1645 .tuner_type = UNSET,
1646 .tuner_addr = ADDR_UNSET,
1647 .radio_addr = ADDR_UNSET,
1649 [BTTV_BOARD_RV605] = {
1650 /* Miguel Freitas <miguel@cetuc.puc-rio.br> */
1651 .name = "RemoteVision MX (RV605)",
1657 .gpiomask2 = 0x07ff,
1658 .muxsel = { 0x33, 0x13, 0x23, 0x43, 0xf3, 0x73, 0xe3, 0x03,
1659 0xd3, 0xb3, 0xc3, 0x63, 0x93, 0x53, 0x83, 0xa3 },
1662 .tuner_type = UNSET,
1663 .tuner_addr = ADDR_UNSET,
1664 .radio_addr = ADDR_UNSET,
1665 .muxsel_hook = rv605_muxsel,
1667 [BTTV_BOARD_POWERCLR_MTV878] = {
1668 .name = "Powercolor MTV878/ MTV878R/ MTV878F",
1673 .gpiomask = 0x1C800F, /* Bit0-2: Audio select, 8-12:remote control 14:remote valid 15:remote reset */
1674 .muxsel = { 2, 1, 1, },
1675 .gpiomux = { 0, 1, 2, 2 },
1678 .tuner_type = TUNER_PHILIPS_PAL,
1679 .tuner_addr = ADDR_UNSET,
1680 .radio_addr = ADDR_UNSET,
1685 /* ---- card 0x4c ---------------------------------- */
1686 [BTTV_BOARD_WINDVR] = {
1687 /* Masaki Suzuki <masaki@btree.org> */
1688 .name = "Canopus WinDVR PCI (COMPAQ Presario 3524JP, 5112JP)",
1693 .gpiomask = 0x140007,
1694 .muxsel = { 2, 3, 1, 1 },
1695 .gpiomux = { 0, 1, 2, 3 },
1697 .tuner_type = TUNER_PHILIPS_NTSC,
1698 .tuner_addr = ADDR_UNSET,
1699 .radio_addr = ADDR_UNSET,
1700 .audio_mode_gpio= windvr_audio,
1702 [BTTV_BOARD_GRANDTEC_MULTI] = {
1703 .name = "GrandTec Multi Capture Card (Bt878)",
1709 .muxsel = { 2, 3, 1, 0 },
1714 .tuner_type = UNSET,
1715 .tuner_addr = ADDR_UNSET,
1716 .radio_addr = ADDR_UNSET,
1718 [BTTV_BOARD_KWORLD] = {
1719 .name = "Jetway TV/Capture JW-TV878-FBK, Kworld KW-TV878RF",
1725 .muxsel = { 2, 3, 1, 1 }, /* Tuner, SVid, SVHS, SVid to SVHS connector */
1726 .gpiomux = { 0, 0, 4, 4 },/* Yes, this tuner uses the same audio output for TV and FM radio!
1727 * This card lacks external Audio In, so we mute it on Ext. & Int.
1728 * The PCB can take a sbx1637/sbx1673, wiring unknown.
1729 * This card lacks PCI subsystem ID, sigh.
1730 * gpiomux =1: lower volume, 2+3: mute
1731 * btwincap uses 0x80000/0x80003
1737 .tuner_type = TUNER_PHILIPS_PAL,
1738 .tuner_addr = ADDR_UNSET,
1739 .radio_addr = ADDR_UNSET,
1740 /* Samsung TCPA9095PC27A (BG+DK), philips compatible, w/FM, stereo and
1741 radio signal strength indicators work fine. */
1744 GPIO0,1: HEF4052 A0,A1
1745 GPIO2: HEF4052 nENABLE
1747 GPIO8-13: IRDC357 data0-5 (data6 n.c. ?) [chip not present on my card]
1751 ?? : mtu8b56ep microcontroller for IR (GPIO wiring unknown)*/
1753 [BTTV_BOARD_DSP_TCVIDEO] = {
1754 /* Arthur Tetzlaff-Deas, DSP Design Ltd <software@dspdesign.com> */
1755 .name = "DSP Design TCVIDEO",
1758 .muxsel = { 2, 3, 1, 0 },
1760 .tuner_type = UNSET,
1761 .tuner_addr = ADDR_UNSET,
1762 .radio_addr = ADDR_UNSET,
1765 /* ---- card 0x50 ---------------------------------- */
1766 [BTTV_BOARD_HAUPPAUGEPVR] = {
1767 .name = "Hauppauge WinTV PVR",
1772 .muxsel = { 2, 0, 1, 1 },
1775 .tuner_type = UNSET,
1776 .tuner_addr = ADDR_UNSET,
1777 .radio_addr = ADDR_UNSET,
1782 [BTTV_BOARD_GVBCTV5PCI] = {
1783 .name = "IODATA GV-BCTV5/PCI",
1788 .gpiomask = 0x0f0f80,
1789 .muxsel = {2, 3, 1, 0 },
1790 .gpiomux = {0x030000, 0x010000, 0, 0 },
1791 .gpiomute = 0x020000,
1794 .tuner_type = TUNER_PHILIPS_NTSC_M,
1795 .tuner_addr = ADDR_UNSET,
1796 .radio_addr = ADDR_UNSET,
1797 .audio_mode_gpio= gvbctv5pci_audio,
1800 [BTTV_BOARD_OSPREY1x0] = {
1801 .name = "Osprey 100/150 (878)", /* 0x1(2|3)-45C6-C1 */
1802 .video_inputs = 4, /* id-inputs-clock */
1806 .muxsel = { 3, 2, 0, 1 },
1808 .tuner_type = UNSET,
1809 .tuner_addr = ADDR_UNSET,
1810 .radio_addr = ADDR_UNSET,
1815 [BTTV_BOARD_OSPREY1x0_848] = {
1816 .name = "Osprey 100/150 (848)", /* 0x04-54C0-C1 & older boards */
1821 .muxsel = { 2, 3, 1 },
1823 .tuner_type = UNSET,
1824 .tuner_addr = ADDR_UNSET,
1825 .radio_addr = ADDR_UNSET,
1831 /* ---- card 0x54 ---------------------------------- */
1832 [BTTV_BOARD_OSPREY101_848] = {
1833 .name = "Osprey 101 (848)", /* 0x05-40C0-C1 */
1840 .tuner_type = UNSET,
1841 .tuner_addr = ADDR_UNSET,
1842 .radio_addr = ADDR_UNSET,
1847 [BTTV_BOARD_OSPREY1x1] = {
1848 .name = "Osprey 101/151", /* 0x1(4|5)-0004-C4 */
1855 .tuner_type = UNSET,
1856 .tuner_addr = ADDR_UNSET,
1857 .radio_addr = ADDR_UNSET,
1862 [BTTV_BOARD_OSPREY1x1_SVID] = {
1863 .name = "Osprey 101/151 w/ svid", /* 0x(16|17|20)-00C4-C1 */
1870 .tuner_type = UNSET,
1871 .tuner_addr = ADDR_UNSET,
1872 .radio_addr = ADDR_UNSET,
1877 [BTTV_BOARD_OSPREY2xx] = {
1878 .name = "Osprey 200/201/250/251", /* 0x1(8|9|E|F)-0004-C4 */
1885 .tuner_type = UNSET,
1886 .tuner_addr = ADDR_UNSET,
1887 .radio_addr = ADDR_UNSET,
1893 /* ---- card 0x58 ---------------------------------- */
1894 [BTTV_BOARD_OSPREY2x0_SVID] = {
1895 .name = "Osprey 200/250", /* 0x1(A|B)-00C4-C1 */
1902 .tuner_type = UNSET,
1903 .tuner_addr = ADDR_UNSET,
1904 .radio_addr = ADDR_UNSET,
1909 [BTTV_BOARD_OSPREY2x0] = {
1910 .name = "Osprey 210/220/230", /* 0x1(A|B)-04C0-C1 */
1917 .tuner_type = UNSET,
1918 .tuner_addr = ADDR_UNSET,
1919 .radio_addr = ADDR_UNSET,
1924 [BTTV_BOARD_OSPREY500] = {
1925 .name = "Osprey 500", /* 500 */
1932 .tuner_type = UNSET,
1933 .tuner_addr = ADDR_UNSET,
1934 .radio_addr = ADDR_UNSET,
1939 [BTTV_BOARD_OSPREY540] = {
1940 .name = "Osprey 540", /* 540 */
1945 .tuner_type = UNSET,
1946 .tuner_addr = ADDR_UNSET,
1947 .radio_addr = ADDR_UNSET,
1953 /* ---- card 0x5C ---------------------------------- */
1954 [BTTV_BOARD_OSPREY2000] = {
1955 .name = "Osprey 2000", /* 2000 */
1962 .tuner_type = UNSET,
1963 .tuner_addr = ADDR_UNSET,
1964 .radio_addr = ADDR_UNSET,
1967 .no_tda7432 = 1, /* must avoid, conflicts with the bt860 */
1969 [BTTV_BOARD_IDS_EAGLE] = {
1970 /* M G Berberich <berberic@forwiss.uni-passau.de> */
1971 .name = "IDS Eagle",
1975 .tuner_type = UNSET,
1976 .tuner_addr = ADDR_UNSET,
1977 .radio_addr = ADDR_UNSET,
1980 .muxsel = { 0, 1, 2, 3 },
1981 .muxsel_hook = eagle_muxsel,
1986 [BTTV_BOARD_PINNACLESAT] = {
1987 .name = "Pinnacle PCTV Sat",
1992 .tuner_type = UNSET,
1993 .tuner_addr = ADDR_UNSET,
1994 .radio_addr = ADDR_UNSET,
2003 [BTTV_BOARD_FORMAC_PROTV] = {
2004 .name = "Formac ProTV II (bt878)",
2010 /* TV, Comp1, Composite over SVID con, SVID */
2011 .muxsel = { 2, 3, 1, 1 },
2012 .gpiomux = { 2, 2, 0, 0 },
2015 .tuner_type = TUNER_PHILIPS_PAL,
2016 .tuner_addr = ADDR_UNSET,
2017 .radio_addr = ADDR_UNSET,
2019 GPIO=0x00,0x01,0x03: mute (?)
2020 0x02: both TV and radio (tuner: FM1216/I)
2021 The card has onboard audio connectors labeled "cdrom" and "board",
2022 not soldered here, though unknown wiring.
2023 Card lacks: external audio in, pci subsystem id.
2027 /* ---- card 0x60 ---------------------------------- */
2028 [BTTV_BOARD_MACHTV] = {
2035 .muxsel = { 2, 3, 1, 1},
2036 .gpiomux = { 0, 1, 2, 3},
2039 .tuner_type = TUNER_PHILIPS_PAL,
2040 .tuner_addr = ADDR_UNSET,
2041 .radio_addr = ADDR_UNSET,
2044 [BTTV_BOARD_EURESYS_PICOLO] = {
2045 .name = "Euresys Picolo",
2054 .muxsel = { 2, 0, 1},
2056 .tuner_type = UNSET,
2057 .tuner_addr = ADDR_UNSET,
2058 .radio_addr = ADDR_UNSET,
2060 [BTTV_BOARD_PV150] = {
2061 /* Luc Van Hoeylandt <luc@e-magic.be> */
2062 .name = "ProVideo PV150", /* 0x4f */
2073 .tuner_type = UNSET,
2074 .tuner_addr = ADDR_UNSET,
2075 .radio_addr = ADDR_UNSET,
2077 [BTTV_BOARD_AD_TVK503] = {
2078 /* Hiroshi Takekawa <sian@big.or.jp> */
2079 /* This card lacks subsystem ID */
2080 .name = "AD-TVK503", /* 0x63 */
2085 .gpiomask = 0x001e8007,
2086 .muxsel = { 2, 3, 1, 0 },
2087 /* Tuner, Radio, external, internal, off, on */
2088 .gpiomux = { 0x08, 0x0f, 0x0a, 0x08 },
2093 .tuner_type = TUNER_PHILIPS_NTSC,
2094 .tuner_addr = ADDR_UNSET,
2095 .radio_addr = ADDR_UNSET,
2096 .audio_mode_gpio= adtvk503_audio,
2099 /* ---- card 0x64 ---------------------------------- */
2100 [BTTV_BOARD_HERCULES_SM_TV] = {
2101 .name = "Hercules Smart TV Stereo",
2107 .muxsel = { 2, 3, 1, 1 },
2111 .tuner_type = TUNER_PHILIPS_PAL,
2112 .tuner_addr = ADDR_UNSET,
2113 .radio_addr = ADDR_UNSET,
2115 - card lacks subsystem ID
2116 - stereo variant w/ daughter board with tda9874a @0xb0
2118 always from tda9874 independent of GPIO (?)
2119 external line in: unknown
2120 - Other chips: em78p156elp @ 0x96 (probably IR remote control)
2121 hef4053 (instead 4052) for unknown function
2124 [BTTV_BOARD_PACETV] = {
2125 .name = "Pace TV & Radio Card",
2130 .muxsel = { 2, 3, 1, 1 }, /* Tuner, CVid, SVid, CVid over SVid connector */
2134 .tuner_type = TUNER_PHILIPS_PAL_I,
2135 .tuner_addr = ADDR_UNSET,
2136 .radio_addr = ADDR_UNSET,
2139 /* Bt878, Bt832, FI1246 tuner; no pci subsystem id
2140 only internal line out: (4pin header) RGGL
2141 Radio must be decoded by msp3410d (not routed through)*/
2143 .digital_mode = DIGITAL_MODE_CAMERA, todo!
2146 [BTTV_BOARD_IVC200] = {
2147 /* Chris Willing <chris@vislab.usyd.edu.au> */
2152 .tuner_type = UNSET,
2153 .tuner_addr = ADDR_UNSET,
2154 .radio_addr = ADDR_UNSET,
2160 [BTTV_BOARD_XGUARD] = {
2161 .name = "Grand X-Guard / Trust 814PCI",
2166 .tuner_type = TUNER_ABSENT,
2167 .tuner_addr = ADDR_UNSET,
2168 .radio_addr = ADDR_UNSET,
2170 .muxsel = { 2,2,2,2, 3,3,3,3, 1,1,1,1, 0,0,0,0 },
2171 .muxsel_hook = xguard_muxsel,
2178 /* ---- card 0x68 ---------------------------------- */
2179 [BTTV_BOARD_NEBULA_DIGITV] = {
2180 .name = "Nebula Electronics DigiTV",
2184 .muxsel = { 2, 3, 1, 0 },
2189 .tuner_type = UNSET,
2190 .tuner_addr = ADDR_UNSET,
2191 .radio_addr = ADDR_UNSET,
2197 [BTTV_BOARD_PV143] = {
2198 /* Jorge Boncompte - DTI2 <jorge@dti2.net> */
2199 .name = "ProVideo PV143",
2205 .muxsel = { 2, 3, 1, 0 },
2210 .tuner_type = UNSET,
2211 .tuner_addr = ADDR_UNSET,
2212 .radio_addr = ADDR_UNSET,
2214 [BTTV_BOARD_VD009X1_MINIDIN] = {
2215 /* M.Klahr@phytec.de */
2216 .name = "PHYTEC VD-009-X1 MiniDIN (bt878)",
2219 .tuner = UNSET, /* card has no tuner */
2222 .muxsel = { 2, 3, 1, 0 },
2223 .gpiomux = { 0, 0, 0, 0 }, /* card has no audio */
2226 .tuner_type = UNSET,
2227 .tuner_addr = ADDR_UNSET,
2228 .radio_addr = ADDR_UNSET,
2230 [BTTV_BOARD_VD009X1_COMBI] = {
2231 .name = "PHYTEC VD-009-X1 Combi (bt878)",
2234 .tuner = UNSET, /* card has no tuner */
2237 .muxsel = { 2, 3, 1, 1 },
2238 .gpiomux = { 0, 0, 0, 0 }, /* card has no audio */
2241 .tuner_type = UNSET,
2242 .tuner_addr = ADDR_UNSET,
2243 .radio_addr = ADDR_UNSET,
2246 /* ---- card 0x6c ---------------------------------- */
2247 [BTTV_BOARD_VD009_MINIDIN] = {
2248 .name = "PHYTEC VD-009 MiniDIN (bt878)",
2251 .tuner = UNSET, /* card has no tuner */
2254 .gpiomask2 = 0x03, /* gpiomask2 defines the bits used to switch audio
2255 via the upper nibble of muxsel. here: used for
2256 xternal video-mux */
2257 .muxsel = { 0x02, 0x12, 0x22, 0x32, 0x03, 0x13, 0x23, 0x33, 0x01, 0x00 },
2258 .gpiomux = { 0, 0, 0, 0 }, /* card has no audio */
2261 .tuner_type = UNSET,
2262 .tuner_addr = ADDR_UNSET,
2263 .radio_addr = ADDR_UNSET,
2265 [BTTV_BOARD_VD009_COMBI] = {
2266 .name = "PHYTEC VD-009 Combi (bt878)",
2269 .tuner = UNSET, /* card has no tuner */
2272 .gpiomask2 = 0x03, /* gpiomask2 defines the bits used to switch audio
2273 via the upper nibble of muxsel. here: used for
2274 xternal video-mux */
2275 .muxsel = { 0x02, 0x12, 0x22, 0x32, 0x03, 0x13, 0x23, 0x33, 0x01, 0x01 },
2276 .gpiomux = { 0, 0, 0, 0 }, /* card has no audio */
2279 .tuner_type = UNSET,
2280 .tuner_addr = ADDR_UNSET,
2281 .radio_addr = ADDR_UNSET,
2283 [BTTV_BOARD_IVC100] = {
2288 .tuner_type = UNSET,
2289 .tuner_addr = ADDR_UNSET,
2290 .radio_addr = ADDR_UNSET,
2293 .muxsel = { 2, 3, 1, 0 },
2296 [BTTV_BOARD_IVC120] = {
2297 /* IVC-120G - Alan Garfield <alan@fromorbit.com> */
2300 .audio_inputs = 0, /* card has no audio */
2301 .tuner = UNSET, /* card has no tuner */
2302 .tuner_type = UNSET,
2303 .tuner_addr = ADDR_UNSET,
2304 .radio_addr = ADDR_UNSET,
2305 .svhs = UNSET, /* card has no svhs */
2311 .muxsel = { 0x01, 0x02, 0x03, 0x04, 0x05, 0x06, 0x07, 0x08,
2312 0x09, 0x0a, 0x0b, 0x0c, 0x0d, 0x0e, 0x0f, 0x10 },
2313 .muxsel_hook = ivc120_muxsel,
2317 /* ---- card 0x70 ---------------------------------- */
2318 [BTTV_BOARD_PC_HDTV] = {
2319 .name = "pcHDTV HD-2000 TV",
2324 .muxsel = { 2, 3, 1, 0 },
2325 .tuner_type = TUNER_PHILIPS_ATSC,
2326 .tuner_addr = ADDR_UNSET,
2327 .radio_addr = ADDR_UNSET,
2330 [BTTV_BOARD_TWINHAN_DST] = {
2331 .name = "Twinhan DST + clones",
2335 .tuner_type = TUNER_ABSENT,
2336 .tuner_addr = ADDR_UNSET,
2337 .radio_addr = ADDR_UNSET,
2341 [BTTV_BOARD_WINFASTVC100] = {
2342 .name = "Winfast VC100",
2347 .muxsel = { 3, 1, 1, 3 }, /* Vid In, SVid In, Vid over SVid in connector */
2351 .tuner_type = TUNER_ABSENT,
2352 .tuner_addr = ADDR_UNSET,
2353 .radio_addr = ADDR_UNSET,
2356 [BTTV_BOARD_TEV560] = {
2357 .name = "Teppro TEV-560/InterVision IV-560",
2363 .muxsel = { 2, 3, 1, 1 },
2364 .gpiomux = { 1, 1, 1, 1 },
2366 .tuner_type = TUNER_PHILIPS_PAL,
2367 .tuner_addr = ADDR_UNSET,
2368 .radio_addr = ADDR_UNSET,
2372 /* ---- card 0x74 ---------------------------------- */
2373 [BTTV_BOARD_SIMUS_GVC1100] = {
2374 .name = "SIMUS GVC1100",
2379 .tuner_type = UNSET,
2380 .tuner_addr = ADDR_UNSET,
2381 .radio_addr = ADDR_UNSET,
2383 .muxsel = { 2, 2, 2, 2 },
2385 .muxsel_hook = gvc1100_muxsel,
2387 [BTTV_BOARD_NGSTV_PLUS] = {
2388 /* Carlos Silva r3pek@r3pek.homelinux.org || card 0x75 */
2389 .name = "NGS NGSTV+",
2393 .gpiomask = 0x008007,
2394 .muxsel = { 2, 3, 0, 0 },
2395 .gpiomux = { 0, 0, 0, 0 },
2396 .gpiomute = 0x000003,
2398 .tuner_type = TUNER_PHILIPS_PAL,
2399 .tuner_addr = ADDR_UNSET,
2400 .radio_addr = ADDR_UNSET,
2403 [BTTV_BOARD_LMLBT4] = {
2404 /* http://linuxmedialabs.com */
2406 .video_inputs = 4, /* IN1,IN2,IN3,IN4 */
2410 .muxsel = { 2, 3, 1, 0 },
2415 .tuner_type = UNSET,
2416 .tuner_addr = ADDR_UNSET,
2417 .radio_addr = ADDR_UNSET,
2419 [BTTV_BOARD_TEKRAM_M205] = {
2420 /* Helmroos Harri <harri.helmroos@pp.inet.fi> */
2421 .name = "Tekram M205 PRO",
2425 .tuner_type = TUNER_PHILIPS_PAL,
2426 .tuner_addr = ADDR_UNSET,
2427 .radio_addr = ADDR_UNSET,
2431 .muxsel = { 2, 3, 1 },
2432 .gpiomux = { 0x68, 0x68, 0x61, 0x61 },
2436 /* ---- card 0x78 ---------------------------------- */
2437 [BTTV_BOARD_CONTVFMI] = {
2438 /* Javier Cendan Ares <jcendan@lycos.es> */
2439 /* bt878 TV + FM without subsystem ID */
2440 .name = "Conceptronic CONTVFMi",
2445 .gpiomask = 0x008007,
2446 .muxsel = { 2, 3, 1, 1 },
2447 .gpiomux = { 0, 1, 2, 2 },
2451 .tuner_type = TUNER_PHILIPS_PAL,
2452 .tuner_addr = ADDR_UNSET,
2453 .radio_addr = ADDR_UNSET,
2457 [BTTV_BOARD_PICOLO_TETRA_CHIP] = {
2458 /*Eric DEBIEF <debief@telemsa.com>*/
2459 /*EURESYS Picolo Tetra : 4 Conexant Fusion 878A, no audio, video input set with analog multiplexers GPIO controled*/
2460 /* adds picolo_tetra_muxsel(), picolo_tetra_init(), the folowing declaration strucure, and #define BTTV_BOARD_PICOLO_TETRA_CHIP*/
2462 .name = "Euresys Picolo Tetra",
2468 .gpiomask2 = 0x3C<<16,/*Set the GPIO[18]->GPIO[21] as output pin.==> drive the video inputs through analog multiplexers*/
2472 .muxsel = {2,2,2,2},/*878A input is always MUX0, see above.*/
2473 .gpiomux = { 0, 0, 0, 0 }, /* card has no audio */
2476 .muxsel_hook = picolo_tetra_muxsel,/*Required as it doesn't follow the classic input selection policy*/
2477 .tuner_type = UNSET,
2478 .tuner_addr = ADDR_UNSET,
2479 .radio_addr = ADDR_UNSET,
2481 [BTTV_BOARD_SPIRIT_TV] = {
2482 /* Spirit TV Tuner from http://spiritmodems.com.au */
2483 /* Stafford Goodsell <surge@goliath.homeunix.org> */
2484 .name = "Spirit TV Tuner",
2489 .gpiomask = 0x0000000f,
2490 .muxsel = { 2, 1, 1 },
2491 .gpiomux = { 0x02, 0x00, 0x00, 0x00 },
2492 .tuner_type = TUNER_TEMIC_PAL,
2493 .tuner_addr = ADDR_UNSET,
2494 .radio_addr = ADDR_UNSET,
2498 [BTTV_BOARD_AVDVBT_771] = {
2499 /* Wolfram Joost <wojo@frokaschwei.de> */
2500 .name = "AVerMedia AVerTV DVB-T 771",
2504 .tuner_type = TUNER_ABSENT,
2505 .tuner_addr = ADDR_UNSET,
2506 .radio_addr = ADDR_UNSET,
2507 .muxsel = { 3 , 3 },
2516 /* ---- card 0x7c ---------------------------------- */
2517 [BTTV_BOARD_AVDVBT_761] = {
2518 /* Matt Jesson <dvb@jesson.eclipse.co.uk> */
2519 /* Based on the Nebula card data - added remote and new card number - BTTV_BOARD_AVDVBT_761, see also ir-kbd-gpio.c */
2520 .name = "AverMedia AverTV DVB-T 761",
2524 .muxsel = { 3, 1, 2, 0 }, /* Comp0, S-Video, ?, ? */
2529 .tuner_type = UNSET,
2530 .tuner_addr = ADDR_UNSET,
2531 .radio_addr = ADDR_UNSET,
2536 [BTTV_BOARD_MATRIX_VISIONSQ] = {
2537 /* andre.schwarz@matrix-vision.de */
2538 .name = "MATRIX Vision Sigma-SQ",
2544 .muxsel = { 2, 2, 2, 2, 2, 2, 2, 2,
2545 3, 3, 3, 3, 3, 3, 3, 3 },
2546 .muxsel_hook = sigmaSQ_muxsel,
2550 .tuner_type = UNSET,
2551 .tuner_addr = ADDR_UNSET,
2552 .radio_addr = ADDR_UNSET,
2554 [BTTV_BOARD_MATRIX_VISIONSLC] = {
2555 /* andre.schwarz@matrix-vision.de */
2556 .name = "MATRIX Vision Sigma-SLC",
2562 .muxsel = { 2, 2, 2, 2 },
2563 .muxsel_hook = sigmaSLC_muxsel,
2567 .tuner_type = UNSET,
2568 .tuner_addr = ADDR_UNSET,
2569 .radio_addr = ADDR_UNSET,
2571 /* BTTV_BOARD_APAC_VIEWCOMP */
2572 [BTTV_BOARD_APAC_VIEWCOMP] = {
2573 /* Attila Kondoros <attila.kondoros@chello.hu> */
2574 /* bt878 TV + FM 0x00000000 subsystem ID */
2575 .name = "APAC Viewcomp 878(AMAX)",
2581 .muxsel = { 2, 3, 1, 1 },
2582 .gpiomux = { 2, 0, 0, 0 },
2586 .tuner_type = TUNER_PHILIPS_PAL,
2587 .tuner_addr = ADDR_UNSET,
2588 .radio_addr = ADDR_UNSET,
2589 .has_remote = 1, /* miniremote works, see ir-kbd-gpio.c */
2590 .has_radio = 1, /* not every card has radio */
2593 /* ---- card 0x80 ---------------------------------- */
2594 [BTTV_BOARD_DVICO_DVBT_LITE] = {
2595 /* Chris Pascoe <c.pascoe@itee.uq.edu.au> */
2596 .name = "DViCO FusionHDTV DVB-T Lite",
2604 .tuner_type = UNSET,
2605 .tuner_addr = ADDR_UNSET,
2606 .radio_addr = ADDR_UNSET,
2608 [BTTV_BOARD_VGEAR_MYVCD] = {
2609 /* Steven <photon38@pchome.com.tw> */
2610 .name = "V-Gear MyVCD",
2616 .muxsel = {2, 3, 1, 0 },
2617 .gpiomux = {0x31, 0x31, 0x31, 0x31 },
2621 .tuner_type = TUNER_PHILIPS_NTSC_M,
2622 .tuner_addr = ADDR_UNSET,
2623 .radio_addr = ADDR_UNSET,
2626 [BTTV_BOARD_SUPER_TV] = {
2627 /* Rick C <cryptdragoon@gmail.com> */
2628 .name = "Super TV Tuner",
2633 .muxsel = { 2, 3, 1, 0 },
2634 .tuner_type = TUNER_PHILIPS_NTSC,
2635 .tuner_addr = ADDR_UNSET,
2636 .radio_addr = ADDR_UNSET,
2637 .gpiomask = 0x008007,
2638 .gpiomux = { 0, 0x000001,0,0 },
2642 [BTTV_BOARD_TIBET_CS16] = {
2643 /* Chris Fanning <video4linux@haydon.net> */
2644 .name = "Tibet Systems 'Progress DVR' CS16",
2649 .muxsel = { 2, 2, 2, 2, 2, 2, 2, 2, 2, 2, 2, 2, 2, 2, 2, 2 },
2654 .tuner_type = UNSET,
2655 .tuner_addr = ADDR_UNSET,
2656 .radio_addr = ADDR_UNSET,
2657 .muxsel_hook = tibetCS16_muxsel,
2659 [BTTV_BOARD_KODICOM_4400R] = {
2660 /* Bill Brack <wbrack@mmm.com.hk> */
2662 * Note that, because of the card's wiring, the "master"
2663 * BT878A chip (i.e. the one which controls the analog switch
2664 * and must use this card type) is the 2nd one detected. The
2665 * other 3 chips should use card type 0x85, whose description
2666 * follows this one. There is a EEPROM on the card (which is
2667 * connected to the I2C of one of those other chips), but is
2668 * not currently handled. There is also a facility for a
2669 * "monitor", which is also not currently implemented.
2671 .name = "Kodicom 4400R (master)",
2675 .tuner_type = UNSET,
2676 .tuner_addr = ADDR_UNSET,
2677 .radio_addr = ADDR_UNSET,
2679 /* GPIO bits 0-9 used for analog switch:
2680 * 00 - 03: camera selector
2681 * 04 - 06: channel (controller) selector
2682 * 07: data (1->on, 0->off)
2685 * bit 16 is input from sync separator for the channel
2687 .gpiomask = 0x0003ff,
2689 .muxsel = { 3, 3, 3, 3, 3, 3, 3, 3, 3, 3, 3, 3, 3, 3, 3, 3 },
2694 .muxsel_hook = kodicom4400r_muxsel,
2696 [BTTV_BOARD_KODICOM_4400R_SL] = {
2697 /* Bill Brack <wbrack@mmm.com.hk> */
2698 /* Note that, for reasons unknown, the "master" BT878A chip (i.e. the
2699 * one which controls the analog switch, and must use the card type)
2700 * is the 2nd one detected. The other 3 chips should use this card
2703 .name = "Kodicom 4400R (slave)",
2707 .tuner_type = UNSET,
2708 .tuner_addr = ADDR_UNSET,
2709 .radio_addr = ADDR_UNSET,
2711 .gpiomask = 0x010000,
2713 .muxsel = { 3, 3, 3, 3, 3, 3, 3, 3, 3, 3, 3, 3, 3, 3, 3, 3 },
2718 .muxsel_hook = kodicom4400r_muxsel,
2720 /* ---- card 0x86---------------------------------- */
2721 [BTTV_BOARD_ADLINK_RTV24] = {
2722 /* Michael Henson <mhenson@clarityvi.com> */
2723 /* Adlink RTV24 with special unlock codes */
2724 .name = "Adlink RTV24",
2729 .muxsel = { 2, 3, 1, 0 },
2730 .tuner_type = UNSET,
2731 .tuner_addr = ADDR_UNSET,
2732 .radio_addr = ADDR_UNSET,
2735 /* ---- card 0x87---------------------------------- */
2736 [BTTV_BOARD_DVICO_FUSIONHDTV_5_LITE] = {
2737 /* Michael Krufky <mkrufky@m1k.net> */
2738 .name = "DViCO FusionHDTV 5 Lite",
2740 .tuner_type = TUNER_LG_TDVS_H06XF, /* TDVS-H064F */
2741 .tuner_addr = ADDR_UNSET,
2742 .radio_addr = ADDR_UNSET,
2746 .muxsel = { 2, 3, 1 },
2747 .gpiomask = 0x00e00007,
2748 .gpiomux = { 0x00400005, 0, 0x00000001, 0 },
2749 .gpiomute = 0x00c00007,
2755 /* ---- card 0x88---------------------------------- */
2756 [BTTV_BOARD_ACORP_Y878F] = {
2757 /* Mauro Carvalho Chehab <mchehab@infradead.org> */
2758 .name = "Acorp Y878F",
2763 .gpiomask = 0x01fe00,
2764 .muxsel = { 2, 3, 1, 1 },
2765 .gpiomux = { 0x001e00, 0, 0x018000, 0x014000 },
2766 .gpiomute = 0x002000,
2769 .tuner_type = TUNER_YMEC_TVF66T5_B_DFF,
2770 .tuner_addr = 0xc1 >>1,
2771 .radio_addr = 0xc1 >>1,
2774 /* ---- card 0x89 ---------------------------------- */
2775 [BTTV_BOARD_CONCEPTRONIC_CTVFMI2] = {
2776 .name = "Conceptronic CTVFMi v2",
2781 .gpiomask = 0x001c0007,
2782 .muxsel = { 2, 3, 1, 1 },
2783 .gpiomux = { 0, 1, 2, 2 },
2787 .tuner_type = TUNER_TENA_9533_DI,
2788 .tuner_addr = ADDR_UNSET,
2789 .radio_addr = ADDR_UNSET,
2793 /* ---- card 0x8a ---------------------------------- */
2794 [BTTV_BOARD_PV_BT878P_2E] = {
2795 .name = "Prolink Pixelview PV-BT878P+ (Rev.2E)",
2800 .gpiomask = 0x01fe00,
2801 .muxsel = { 2,3,1,1,-1 },
2802 .digital_mode = DIGITAL_MODE_CAMERA,
2803 .gpiomux = { 0x00400, 0x10400, 0x04400, 0x80000 },
2804 .gpiomute = 0x12400,
2807 .tuner_type = TUNER_LG_PAL_FM,
2808 .tuner_addr = ADDR_UNSET,
2809 .radio_addr = ADDR_UNSET,
2812 /* ---- card 0x8b ---------------------------------- */
2813 [BTTV_BOARD_PV_M4900] = {
2814 /* Sérgio Fortier <sergiofortier@yahoo.com.br> */
2815 .name = "Prolink PixelView PlayTV MPEG2 PV-M4900",
2821 .muxsel = { 2, 3, 1, 1 },
2822 .gpiomux = { 0x21, 0x20, 0x24, 0x2c },
2826 .tuner_type = TUNER_YMEC_TVF_5533MF,
2827 .tuner_addr = ADDR_UNSET,
2828 .radio_addr = ADDR_UNSET,
2832 /* ---- card 0x8c ---------------------------------- */
2833 /* Has four Bt878 chips behind a PCI bridge, each chip has:
2834 one external BNC composite input (mux 2)
2835 three internal composite inputs (unknown muxes)
2836 an 18-bit stereo A/D (CS5331A), which has:
2837 one external stereo unblanced (RCA) audio connection
2838 one (or 3?) internal stereo balanced (XLR) audio connection
2839 input is selected via gpio to a 14052B mux
2840 (mask=0x300, unbal=0x000, bal=0x100, ??=0x200,0x300)
2841 gain is controlled via an X9221A chip on the I2C bus @0x28
2842 sample rate is controlled via gpio to an MK1413S
2843 (mask=0x3, 32kHz=0x0, 44.1kHz=0x1, 48kHz=0x2, ??=0x3)
2844 There is neither a tuner nor an svideo input. */
2845 [BTTV_BOARD_OSPREY440] = {
2846 .name = "Osprey 440",
2848 .audio_inputs = 2, /* this is meaningless */
2851 .muxsel = { 2, 3, 0, 1 }, /* 3,0,1 are guesses */
2853 .gpiomute = 0x000, /* int + 32kHz */
2854 .gpiomux = { 0, 0, 0x000, 0x100},
2856 .tuner_type = UNSET,
2857 .tuner_addr = ADDR_UNSET,
2858 .radio_addr = ADDR_UNSET,
2863 /* ---- card 0x8d ---------------------------------- */
2864 [BTTV_BOARD_ASOUND_SKYEYE] = {
2865 .name = "Asound Skyeye PCTV",
2871 .muxsel = { 2, 3, 1, 1 },
2872 .gpiomux = { 2, 0, 0, 0 },
2876 .tuner_type = TUNER_PHILIPS_NTSC,
2877 .tuner_addr = ADDR_UNSET,
2878 .radio_addr = ADDR_UNSET,
2880 /* ---- card 0x8e ---------------------------------- */
2881 [BTTV_BOARD_SABRENT_TVFM] = {
2882 .name = "Sabrent TV-FM (bttv version)",
2887 .gpiomask = 0x108007,
2888 .muxsel = { 2, 3, 1, 1 },
2889 .gpiomux = { 100000, 100002, 100002, 100000 },
2894 .tuner_type = TUNER_TNF_5335MF,
2895 .tuner_addr = ADDR_UNSET,
2898 /* ---- card 0x8f ---------------------------------- */
2899 [BTTV_BOARD_HAUPPAUGE_IMPACTVCB] = {
2900 .name = "Hauppauge ImpactVCB (bt878)",
2905 .gpiomask = 0x0f, /* old: 7 */
2906 .muxsel = { 0, 1, 3, 2 }, /* Composite 0-3 */
2910 .tuner_type = UNSET,
2911 .tuner_addr = ADDR_UNSET,
2912 .radio_addr = ADDR_UNSET,
2914 [BTTV_BOARD_MACHTV_MAGICTV] = {
2915 /* Julian Calaby <julian.calaby@gmail.com>
2916 * Slightly different from original MachTV definition (0x60)
2918 * FIXME: RegSpy says gpiomask should be "0x001c800f", but it
2919 * stuffs up remote chip. Bug is a pin on the jaecs is not set
2920 * properly (methinks) causing no keyup bits being set */
2922 .name = "MagicTV", /* rebranded MachTV */
2928 .muxsel = { 2, 3, 1, 1 },
2929 .gpiomux = { 0, 1, 2, 3 },
2931 .tuner_type = TUNER_TEMIC_4009FR5_PAL,
2932 .tuner_addr = ADDR_UNSET,
2933 .radio_addr = ADDR_UNSET,
2938 [BTTV_BOARD_SSAI_SECURITY] = {
2939 .name = "SSAI Security Video Interface",
2944 .muxsel = { 0, 1, 2, 3 },
2945 .tuner_type = UNSET,
2946 .tuner_addr = ADDR_UNSET,
2947 .radio_addr = ADDR_UNSET,
2949 [BTTV_BOARD_SSAI_ULTRASOUND] = {
2950 .name = "SSAI Ultrasound Video Interface",
2955 .muxsel = { 2, 0, 1, 3 },
2956 .tuner_type = UNSET,
2957 .tuner_addr = ADDR_UNSET,
2958 .radio_addr = ADDR_UNSET,
2960 /* ---- card 0x94---------------------------------- */
2961 [BTTV_BOARD_DVICO_FUSIONHDTV_2] = {
2962 .name = "DViCO FusionHDTV 2",
2964 .tuner_type = TUNER_PHILIPS_ATSC, /* FCV1236D */
2965 .tuner_addr = ADDR_UNSET,
2966 .radio_addr = ADDR_UNSET,
2970 .muxsel = { 2, 3, 1 },
2971 .gpiomask = 0x00e00007,
2972 .gpiomux = { 0x00400005, 0, 0x00000001, 0 },
2973 .gpiomute = 0x00c00007,
2978 /* ---- card 0x95---------------------------------- */
2979 [BTTV_BOARD_TYPHOON_TVTUNERPCI] = {
2980 .name = "Typhoon TV-Tuner PCI (50684)",
2985 .gpiomask = 0x3014f,
2986 .muxsel = { 2, 3, 1, 1 },
2987 .gpiomux = { 0x20001,0x10001, 0, 0 },
2991 .tuner_type = TUNER_PHILIPS_PAL_I,
2992 .tuner_addr = ADDR_UNSET,
2993 .radio_addr = ADDR_UNSET,
2997 static const unsigned int bttv_num_tvcards = ARRAY_SIZE(bttv_tvcards);
2999 /* ----------------------------------------------------------------------- */
3001 static unsigned char eeprom_data[256];
3006 void __devinit bttv_idcard(struct bttv *btv)
3008 unsigned int gpiobits;
3012 /* read PCI subsystem ID */
3013 pci_read_config_word(btv->c.pci, PCI_SUBSYSTEM_ID, &tmp);
3014 btv->cardid = tmp << 16;
3015 pci_read_config_word(btv->c.pci, PCI_SUBSYSTEM_VENDOR_ID, &tmp);
3018 if (0 != btv->cardid && 0xffffffff != btv->cardid) {
3019 /* look for the card */
3020 for (type = -1, i = 0; cards[i].id != 0; i++)
3021 if (cards[i].id == btv->cardid)
3026 printk(KERN_INFO "bttv%d: detected: %s [card=%d], "
3027 "PCI subsystem ID is %04x:%04x\n",
3028 btv->c.nr,cards[type].name,cards[type].cardnr,
3029 btv->cardid & 0xffff,
3030 (btv->cardid >> 16) & 0xffff);
3031 btv->c.type = cards[type].cardnr;
3034 printk(KERN_INFO "bttv%d: subsystem: %04x:%04x (UNKNOWN)\n",
3035 btv->c.nr, btv->cardid & 0xffff,
3036 (btv->cardid >> 16) & 0xffff);
3037 printk(KERN_DEBUG "please mail id, board name and "
3038 "the correct card= insmod option to video4linux-list@redhat.com\n");
3042 /* let the user override the autodetected type */
3043 if (card[btv->c.nr] < bttv_num_tvcards)
3044 btv->c.type=card[btv->c.nr];
3046 /* print which card config we are using */
3047 printk(KERN_INFO "bttv%d: using: %s [card=%d,%s]\n",btv->c.nr,
3048 bttv_tvcards[btv->c.type].name, btv->c.type,
3049 card[btv->c.nr] < bttv_num_tvcards
3050 ? "insmod option" : "autodetected");
3052 /* overwrite gpio stuff ?? */
3053 if (UNSET == audioall && UNSET == audiomux[0])
3056 if (UNSET != audiomux[0]) {
3058 for (i = 0; i < ARRAY_SIZE(bttv_tvcards->gpiomux); i++) {
3059 bttv_tvcards[btv->c.type].gpiomux[i] = audiomux[i];
3060 gpiobits |= audiomux[i];
3063 gpiobits = audioall;
3064 for (i = 0; i < ARRAY_SIZE(bttv_tvcards->gpiomux); i++) {
3065 bttv_tvcards[btv->c.type].gpiomux[i] = audioall;
3068 bttv_tvcards[btv->c.type].gpiomask = (UNSET != gpiomask) ? gpiomask : gpiobits;
3069 printk(KERN_INFO "bttv%d: gpio config override: mask=0x%x, mux=",
3070 btv->c.nr,bttv_tvcards[btv->c.type].gpiomask);
3071 for (i = 0; i < ARRAY_SIZE(bttv_tvcards->gpiomux); i++) {
3072 printk("%s0x%x", i ? "," : "", bttv_tvcards[btv->c.type].gpiomux[i]);
3078 * (most) board specific initialisations goes here
3081 /* Some Modular Technology cards have an eeprom, but no subsystem ID */
3082 static void identify_by_eeprom(struct bttv *btv, unsigned char eeprom_data[256])
3086 if (0 == strncmp(eeprom_data,"GET MM20xPCTV",13))
3087 type = BTTV_BOARD_MODTEC_205;
3088 else if (0 == strncmp(eeprom_data+20,"Picolo",7))
3089 type = BTTV_BOARD_EURESYS_PICOLO;
3090 else if (eeprom_data[0] == 0x84 && eeprom_data[2]== 0)
3091 type = BTTV_BOARD_HAUPPAUGE; /* old bt848 */
3095 printk("bttv%d: detected by eeprom: %s [card=%d]\n",
3096 btv->c.nr, bttv_tvcards[btv->c.type].name, btv->c.type);
3100 static void flyvideo_gpio(struct bttv *btv)
3102 int gpio,has_remote,has_radio,is_capture_only,is_lr90,has_tda9820_tda9821;
3103 int tuner=UNSET,ttype;
3105 gpio_inout(0xffffff, 0);
3106 udelay(8); /* without this we would see the 0x1800 mask */
3108 /* FIXME: must restore OUR_EN ??? */
3110 /* all cards provide GPIO info, some have an additional eeprom
3111 * LR50: GPIO coding can be found lower right CP1 .. CP9
3112 * CP9=GPIO23 .. CP1=GPIO15; when OPEN, the corresponding GPIO reads 1.
3114 * LR90: GP9=GPIO23 .. GP1=GPIO15 (right above the bt878)
3116 * lowest 3 bytes are remote control codes (no handshake needed)
3117 * xxxFFF: No remote control chip soldered
3118 * xxxF00(LR26/LR50), xxxFE0(LR90): Remote control chip (LVA001 or CF45) soldered
3119 * Note: Some bits are Audio_Mask !
3121 ttype=(gpio&0x0f0000)>>16;
3123 case 0x0: tuner=2; /* NTSC, e.g. TPI8NSR11P */
3125 case 0x2: tuner=39;/* LG NTSC (newer TAPC series) TAPC-H701P */
3127 case 0x4: tuner=5; /* Philips PAL TPI8PSB02P, TPI8PSB12P, TPI8PSB12D or FI1216, FM1216 */
3129 case 0x6: tuner=37;/* LG PAL (newer TAPC series) TAPC-G702P */
3131 case 0xC: tuner=3; /* Philips SECAM(+PAL) FQ1216ME or FI1216MF */
3134 printk(KERN_INFO "bttv%d: FlyVideo_gpio: unknown tuner type.\n", btv->c.nr);
3137 has_remote = gpio & 0x800000;
3138 has_radio = gpio & 0x400000;
3139 /* unknown 0x200000;
3140 * unknown2 0x100000; */
3141 is_capture_only = !(gpio & 0x008000); /* GPIO15 */
3142 has_tda9820_tda9821 = !(gpio & 0x004000);
3143 is_lr90 = !(gpio & 0x002000); /* else LR26/LR50 (LR38/LR51 f. capture only) */
3145 * gpio & 0x001000 output bit for audio routing */
3148 tuner = TUNER_ABSENT; /* No tuner present */
3150 printk(KERN_INFO "bttv%d: FlyVideo Radio=%s RemoteControl=%s Tuner=%d gpio=0x%06x\n",
3151 btv->c.nr, has_radio? "yes":"no ", has_remote? "yes":"no ", tuner, gpio);
3152 printk(KERN_INFO "bttv%d: FlyVideo LR90=%s tda9821/tda9820=%s capture_only=%s\n",
3153 btv->c.nr, is_lr90?"yes":"no ", has_tda9820_tda9821?"yes":"no ",
3154 is_capture_only?"yes":"no ");
3156 if (tuner != UNSET) /* only set if known tuner autodetected, else let insmod option through */
3157 btv->tuner_type = tuner;
3158 btv->has_radio = has_radio;
3160 /* LR90 Audio Routing is done by 2 hef4052, so Audio_Mask has 4 bits: 0x001c80
3161 * LR26/LR50 only has 1 hef4052, Audio_Mask 0x000c00
3162 * Audio options: from tuner, from tda9821/tda9821(mono,stereo,sap), from tda9874, ext., mute */
3163 if(has_tda9820_tda9821) btv->audio_mode_gpio = lt9415_audio;
3164 /* todo: if(has_tda9874) btv->audio_mode_gpio = fv2000s_audio; */
3167 static int miro_tunermap[] = { 0,6,2,3, 4,5,6,0, 3,0,4,5, 5,2,16,1,
3168 14,2,17,1, 4,1,4,3, 1,2,16,1, 4,4,4,4 };
3169 static int miro_fmtuner[] = { 0,0,0,0, 0,0,0,0, 0,0,0,0, 0,0,0,1,
3170 1,1,1,1, 1,1,1,0, 0,0,0,0, 0,1,0,0 };
3172 static void miro_pinnacle_gpio(struct bttv *btv)
3177 gpio_inout(0xffffff, 0);
3179 id = ((gpio>>10) & 63) -1;
3180 msp = bttv_I2CRead(btv, I2C_ADDR_MSP3400, "MSP34xx");
3182 btv->tuner_type = miro_tunermap[id];
3183 if (0 == (gpio & 0x20)) {
3185 if (!miro_fmtuner[id]) {
3186 btv->has_matchbox = 1;
3187 btv->mbox_we = (1<<6);
3188 btv->mbox_most = (1<<7);
3189 btv->mbox_clk = (1<<8);
3190 btv->mbox_data = (1<<9);
3191 btv->mbox_mask = (1<<6)|(1<<7)|(1<<8)|(1<<9);
3197 if (btv->c.type == BTTV_BOARD_MIRO)
3198 btv->c.type = BTTV_BOARD_MIROPRO;
3199 if (btv->c.type == BTTV_BOARD_PINNACLE)
3200 btv->c.type = BTTV_BOARD_PINNACLEPRO;
3203 "bttv%d: miro: id=%d tuner=%d radio=%s stereo=%s\n",
3204 btv->c.nr, id+1, btv->tuner_type,
3205 !btv->has_radio ? "no" :
3206 (btv->has_matchbox ? "matchbox" : "fmtuner"),
3207 (-1 == msp) ? "no" : "yes");
3209 /* new cards with microtune tuner */
3214 info = "PAL / mono";
3215 btv->tda9887_conf = TDA9887_INTERCARRIER;
3218 info = "PAL+SECAM / stereo";
3220 btv->tda9887_conf = TDA9887_QSS;
3223 info = "NTSC / stereo";
3225 btv->tda9887_conf = TDA9887_QSS;
3228 info = "PAL+SECAM / mono";
3229 btv->tda9887_conf = TDA9887_QSS;
3232 info = "NTSC / mono";
3233 btv->tda9887_conf = TDA9887_INTERCARRIER;
3236 info = "NTSC / stereo";
3237 btv->tda9887_conf = TDA9887_INTERCARRIER;
3240 info = "PAL / stereo";
3241 btv->tda9887_conf = TDA9887_INTERCARRIER;
3244 info = "oops: unknown card";
3248 btv->c.type = BTTV_BOARD_PINNACLEPRO;
3250 "bttv%d: pinnacle/mt: id=%d info=\"%s\" radio=%s\n",
3251 btv->c.nr, id, info, btv->has_radio ? "yes" : "no");
3252 btv->tuner_type = TUNER_MT2032;
3256 /* GPIO21 L: Buffer aktiv, H: Buffer inaktiv */
3257 #define LM1882_SYNC_DRIVE 0x200000L
3259 static void init_ids_eagle(struct bttv *btv)
3261 gpio_inout(0xffffff,0xFFFF37);
3262 gpio_write(0x200020);
3264 /* flash strobe inverter ?! */
3265 gpio_write(0x200024);
3267 /* switch sync drive off */
3268 gpio_bits(LM1882_SYNC_DRIVE,LM1882_SYNC_DRIVE);
3270 /* set BT848 muxel to 2 */
3271 btaor((2)<<5, ~(2<<5), BT848_IFORM);
3274 /* Muxsel helper for the IDS Eagle.
3275 * the eagles does not use the standard muxsel-bits but
3276 * has its own multiplexer */
3277 static void eagle_muxsel(struct bttv *btv, unsigned int input)
3279 btaor((2)<<5, ~(3<<5), BT848_IFORM);
3280 gpio_bits(3,bttv_tvcards[btv->c.type].muxsel[input&7]);
3283 /* set chroma ADC to sleep */
3284 btor(BT848_ADC_C_SLEEP, BT848_ADC);
3285 /* set to composite video */
3286 btand(~BT848_CONTROL_COMP, BT848_E_CONTROL);
3287 btand(~BT848_CONTROL_COMP, BT848_O_CONTROL);
3289 /* switch sync drive off */
3290 gpio_bits(LM1882_SYNC_DRIVE,LM1882_SYNC_DRIVE);
3293 static void gvc1100_muxsel(struct bttv *btv, unsigned int input)
3295 static const int masks[] = {0x30, 0x01, 0x12, 0x23};
3296 gpio_write(masks[input%4]);
3299 /* LMLBT4x initialization - to allow access to GPIO bits for sensors input and
3302 GPIObit | 10 | 9 | 8 | 7 | 6 | 5 | 4 | 3 | 2 | 1 | 0 |
3303 assignment | TI | O3|INx| O2| O1|IN4|IN3|IN2|IN1| | |
3305 IN - sensor inputs, INx - sensor inputs and TI XORed together
3306 O1,O2,O3 - alarm outputs (relays)
3308 OUT ENABLE 1 1 0 . 1 1 0 0 . 0 0 0 0 = 0x6C0
3312 static void init_lmlbt4x(struct bttv *btv)
3314 printk(KERN_DEBUG "LMLBT4x init\n");
3315 btwrite(0x000000, BT848_GPIO_REG_INP);
3316 gpio_inout(0xffffff, 0x0006C0);
3317 gpio_write(0x000000);
3320 static void sigmaSQ_muxsel(struct bttv *btv, unsigned int input)
3322 unsigned int inmux = input % 8;
3323 gpio_inout( 0xf, 0xf );
3324 gpio_bits( 0xf, inmux );
3327 static void sigmaSLC_muxsel(struct bttv *btv, unsigned int input)
3329 unsigned int inmux = input % 4;
3330 gpio_inout( 3<<9, 3<<9 );
3331 gpio_bits( 3<<9, inmux<<9 );
3334 /* ----------------------------------------------------------------------- */
3336 static void bttv_reset_audio(struct bttv *btv)
3339 * BT878A has a audio-reset register.
3340 * 1. This register is an audio reset function but it is in
3341 * function-0 (video capture) address space.
3342 * 2. It is enough to do this once per power-up of the card.
3343 * 3. There is a typo in the Conexant doc -- it is not at
3344 * 0x5B, but at 0x058. (B is an odd-number, obviously a typo!).
3345 * --//Shrikumar 030609
3351 printk("bttv%d: BT878A ARESET\n",btv->c.nr);
3352 btwrite((1<<7), 0x058);
3357 /* initialization part one -- before registering i2c bus */
3358 void __devinit bttv_init_card1(struct bttv *btv)
3360 switch (btv->c.type) {
3361 case BTTV_BOARD_HAUPPAUGE:
3362 case BTTV_BOARD_HAUPPAUGE878:
3363 boot_msp34xx(btv,5);
3365 case BTTV_BOARD_VOODOOTV_200:
3366 case BTTV_BOARD_VOODOOTV_FM:
3367 boot_msp34xx(btv,20);
3369 case BTTV_BOARD_AVERMEDIA98:
3370 boot_msp34xx(btv,11);
3372 case BTTV_BOARD_HAUPPAUGEPVR:
3375 case BTTV_BOARD_TWINHAN_DST:
3376 case BTTV_BOARD_AVDVBT_771:
3377 case BTTV_BOARD_PINNACLESAT:
3378 btv->use_i2c_hw = 1;
3380 case BTTV_BOARD_ADLINK_RTV24:
3385 if (!bttv_tvcards[btv->c.type].has_dvb)
3386 bttv_reset_audio(btv);
3389 /* initialization part two -- after registering i2c bus */
3390 void __devinit bttv_init_card2(struct bttv *btv)
3392 int addr=ADDR_UNSET;
3394 btv->tuner_type = UNSET;
3396 if (BTTV_BOARD_UNKNOWN == btv->c.type) {
3397 bttv_readee(btv,eeprom_data,0xa0);
3398 identify_by_eeprom(btv,eeprom_data);
3401 switch (btv->c.type) {
3402 case BTTV_BOARD_MIRO:
3403 case BTTV_BOARD_MIROPRO:
3404 case BTTV_BOARD_PINNACLE:
3405 case BTTV_BOARD_PINNACLEPRO:
3407 miro_pinnacle_gpio(btv);
3409 case BTTV_BOARD_FLYVIDEO_98:
3410 case BTTV_BOARD_MAXI:
3411 case BTTV_BOARD_LIFE_FLYKIT:
3412 case BTTV_BOARD_FLYVIDEO:
3413 case BTTV_BOARD_TYPHOON_TVIEW:
3414 case BTTV_BOARD_CHRONOS_VS2:
3415 case BTTV_BOARD_FLYVIDEO_98FM:
3416 case BTTV_BOARD_FLYVIDEO2000:
3417 case BTTV_BOARD_FLYVIDEO98EZ:
3418 case BTTV_BOARD_CONFERENCETV:
3419 case BTTV_BOARD_LIFETEC_9415:
3422 case BTTV_BOARD_HAUPPAUGE:
3423 case BTTV_BOARD_HAUPPAUGE878:
3424 case BTTV_BOARD_HAUPPAUGEPVR:
3425 /* pick up some config infos from the eeprom */
3426 bttv_readee(btv,eeprom_data,0xa0);
3427 hauppauge_eeprom(btv);
3429 case BTTV_BOARD_AVERMEDIA98:
3430 case BTTV_BOARD_AVPHONE98:
3431 bttv_readee(btv,eeprom_data,0xa0);
3432 avermedia_eeprom(btv);
3434 case BTTV_BOARD_PXC200:
3437 case BTTV_BOARD_PICOLO_TETRA_CHIP:
3438 picolo_tetra_init(btv);
3440 case BTTV_BOARD_VHX:
3442 btv->has_matchbox = 1;
3443 btv->mbox_we = 0x20;
3445 btv->mbox_clk = 0x08;
3446 btv->mbox_data = 0x10;
3447 btv->mbox_mask = 0x38;
3449 case BTTV_BOARD_VOBIS_BOOSTAR:
3450 case BTTV_BOARD_TERRATV:
3451 terratec_active_radio_upgrade(btv);
3453 case BTTV_BOARD_MAGICTVIEW061:
3454 if (btv->cardid == 0x3002144f) {
3456 printk("bttv%d: radio detected by subsystem id (CPH05x)\n",btv->c.nr);
3459 case BTTV_BOARD_STB2:
3460 if (btv->cardid == 0x3060121a) {
3461 /* Fix up entry for 3DFX VoodooTV 100,
3462 which is an OEM STB card variant. */
3464 btv->tuner_type=TUNER_TEMIC_NTSC;
3467 case BTTV_BOARD_OSPREY1x0:
3468 case BTTV_BOARD_OSPREY1x0_848:
3469 case BTTV_BOARD_OSPREY101_848:
3470 case BTTV_BOARD_OSPREY1x1:
3471 case BTTV_BOARD_OSPREY1x1_SVID:
3472 case BTTV_BOARD_OSPREY2xx:
3473 case BTTV_BOARD_OSPREY2x0_SVID:
3474 case BTTV_BOARD_OSPREY2x0:
3475 case BTTV_BOARD_OSPREY440:
3476 case BTTV_BOARD_OSPREY500:
3477 case BTTV_BOARD_OSPREY540:
3478 case BTTV_BOARD_OSPREY2000:
3479 bttv_readee(btv,eeprom_data,0xa0);
3480 osprey_eeprom(btv, eeprom_data);
3482 case BTTV_BOARD_IDS_EAGLE:
3483 init_ids_eagle(btv);
3485 case BTTV_BOARD_MODTEC_205:
3486 bttv_readee(btv,eeprom_data,0xa0);
3489 case BTTV_BOARD_LMLBT4:
3492 case BTTV_BOARD_TIBET_CS16:
3493 tibetCS16_init(btv);
3495 case BTTV_BOARD_KODICOM_4400R:
3496 kodicom4400r_init(btv);
3500 /* pll configuration */
3501 if (!(btv->id==848 && btv->revision==0x11)) {
3502 /* defaults from card list */
3503 if (PLL_28 == bttv_tvcards[btv->c.type].pll) {
3504 btv->pll.pll_ifreq=28636363;
3505 btv->pll.pll_crystal=BT848_IFORM_XT0;
3507 if (PLL_35 == bttv_tvcards[btv->c.type].pll) {
3508 btv->pll.pll_ifreq=35468950;
3509 btv->pll.pll_crystal=BT848_IFORM_XT1;
3511 /* insmod options can override */
3512 switch (pll[btv->c.nr]) {
3514 btv->pll.pll_crystal = 0;
3515 btv->pll.pll_ifreq = 0;
3516 btv->pll.pll_ofreq = 0;
3518 case 1: /* 28 MHz */
3520 btv->pll.pll_ifreq = 28636363;
3521 btv->pll.pll_ofreq = 0;
3522 btv->pll.pll_crystal = BT848_IFORM_XT0;
3524 case 2: /* 35 MHz */
3526 btv->pll.pll_ifreq = 35468950;
3527 btv->pll.pll_ofreq = 0;
3528 btv->pll.pll_crystal = BT848_IFORM_XT1;
3532 btv->pll.pll_current = -1;
3534 /* tuner configuration (from card list / autodetect / insmod option) */
3535 if (ADDR_UNSET != bttv_tvcards[btv->c.type].tuner_addr)
3536 addr = bttv_tvcards[btv->c.type].tuner_addr;
3538 if (UNSET != bttv_tvcards[btv->c.type].tuner_type)
3539 if(UNSET == btv->tuner_type)
3540 btv->tuner_type = bttv_tvcards[btv->c.type].tuner_type;
3541 if (UNSET != tuner[btv->c.nr])
3542 btv->tuner_type = tuner[btv->c.nr];
3544 if (btv->tuner_type == TUNER_ABSENT ||
3545 bttv_tvcards[btv->c.type].tuner == UNSET)
3546 printk(KERN_INFO "bttv%d: tuner absent\n", btv->c.nr);
3547 else if(btv->tuner_type == UNSET)
3548 printk(KERN_WARNING "bttv%d: tuner type unset\n", btv->c.nr);
3550 printk(KERN_INFO "bttv%d: tuner type=%d\n", btv->c.nr,
3553 if (btv->tuner_type != UNSET) {
3554 struct tuner_setup tun_setup;
3556 tun_setup.mode_mask = T_ANALOG_TV | T_DIGITAL_TV;
3557 tun_setup.type = btv->tuner_type;
3558 tun_setup.addr = addr;
3560 bttv_call_i2c_clients(btv, TUNER_SET_TYPE_ADDR, &tun_setup);
3563 if (btv->tda9887_conf) {
3564 struct v4l2_priv_tun_config tda9887_cfg;
3566 tda9887_cfg.tuner = TUNER_TDA9887;
3567 tda9887_cfg.priv = &btv->tda9887_conf;
3569 bttv_call_i2c_clients(btv, TUNER_SET_CONFIG, &tda9887_cfg);
3572 btv->svhs = bttv_tvcards[btv->c.type].svhs;
3573 if (svhs[btv->c.nr] != UNSET)
3574 btv->svhs = svhs[btv->c.nr];
3575 if (remote[btv->c.nr] != UNSET)
3576 btv->has_remote = remote[btv->c.nr];
3578 if (bttv_tvcards[btv->c.type].has_radio)
3580 if (bttv_tvcards[btv->c.type].has_remote)
3582 if (!bttv_tvcards[btv->c.type].no_gpioirq)
3584 if (bttv_tvcards[btv->c.type].volume_gpio)
3585 btv->volume_gpio=bttv_tvcards[btv->c.type].volume_gpio;
3586 if (bttv_tvcards[btv->c.type].audio_mode_gpio)
3587 btv->audio_mode_gpio=bttv_tvcards[btv->c.type].audio_mode_gpio;
3589 if (bttv_tvcards[btv->c.type].digital_mode == DIGITAL_MODE_CAMERA) {
3590 /* detect Bt832 chip for quartzsight digital camera */
3591 if ((bttv_I2CRead(btv, I2C_ADDR_BT832_ALT1, "Bt832") >=0) ||
3592 (bttv_I2CRead(btv, I2C_ADDR_BT832_ALT2, "Bt832") >=0))
3599 if (bttv_tvcards[btv->c.type].tuner == UNSET)
3600 return; /* no tuner or related drivers to load */
3602 /* try to detect audio/fader chips */
3603 if (!bttv_tvcards[btv->c.type].no_msp34xx &&
3604 bttv_I2CRead(btv, I2C_ADDR_MSP3400, "MSP34xx") >=0)
3605 request_module("msp3400");
3607 if (bttv_tvcards[btv->c.type].msp34xx_alt &&
3608 bttv_I2CRead(btv, I2C_ADDR_MSP3400_ALT, "MSP34xx (alternate address)") >=0)
3609 request_module("msp3400");
3611 if (!bttv_tvcards[btv->c.type].no_tda9875 &&
3612 bttv_I2CRead(btv, I2C_ADDR_TDA9875, "TDA9875") >=0)
3613 request_module("tda9875");
3615 if (!bttv_tvcards[btv->c.type].no_tda7432 &&
3616 bttv_I2CRead(btv, I2C_ADDR_TDA7432, "TDA7432") >=0)
3617 request_module("tda7432");
3619 if (bttv_tvcards[btv->c.type].needs_tvaudio)
3620 request_module("tvaudio");
3622 if (btv->tuner_type != UNSET && btv->tuner_type != TUNER_ABSENT)
3623 request_module("tuner");
3627 /* ----------------------------------------------------------------------- */
3629 static void modtec_eeprom(struct bttv *btv)
3631 if( strncmp(&(eeprom_data[0x1e]),"Temic 4066 FY5",14) ==0) {
3632 btv->tuner_type=TUNER_TEMIC_4066FY5_PAL_I;
3633 printk("bttv%d: Modtec: Tuner autodetected by eeprom: %s\n",
3634 btv->c.nr,&eeprom_data[0x1e]);
3635 } else if (strncmp(&(eeprom_data[0x1e]),"Alps TSBB5",10) ==0) {
3636 btv->tuner_type=TUNER_ALPS_TSBB5_PAL_I;
3637 printk("bttv%d: Modtec: Tuner autodetected by eeprom: %s\n",
3638 btv->c.nr,&eeprom_data[0x1e]);
3639 } else if (strncmp(&(eeprom_data[0x1e]),"Philips FM1246",14) ==0) {
3640 btv->tuner_type=TUNER_PHILIPS_NTSC;
3641 printk("bttv%d: Modtec: Tuner autodetected by eeprom: %s\n",
3642 btv->c.nr,&eeprom_data[0x1e]);
3644 printk("bttv%d: Modtec: Unknown TunerString: %s\n",
3645 btv->c.nr,&eeprom_data[0x1e]);
3649 static void __devinit hauppauge_eeprom(struct bttv *btv)
3653 tveeprom_hauppauge_analog(&btv->i2c_client, &tv, eeprom_data);
3654 btv->tuner_type = tv.tuner_type;
3655 btv->has_radio = tv.has_radio;
3657 printk("bttv%d: Hauppauge eeprom indicates model#%d\n",
3658 btv->c.nr, tv.model);
3661 * Some of the 878 boards have duplicate PCI IDs. Switch the board
3662 * type based on model #.
3664 if(tv.model == 64900) {
3665 printk("bttv%d: Switching board type from %s to %s\n",
3667 bttv_tvcards[btv->c.type].name,
3668 bttv_tvcards[BTTV_BOARD_HAUPPAUGE_IMPACTVCB].name);
3669 btv->c.type = BTTV_BOARD_HAUPPAUGE_IMPACTVCB;
3673 static int terratec_active_radio_upgrade(struct bttv *btv)
3678 btv->has_matchbox = 1;
3679 btv->mbox_we = 0x10;
3680 btv->mbox_most = 0x20;
3681 btv->mbox_clk = 0x08;
3682 btv->mbox_data = 0x04;
3683 btv->mbox_mask = 0x3c;
3685 btv->mbox_iow = 1 << 8;
3686 btv->mbox_ior = 1 << 9;
3687 btv->mbox_csel = 1 << 10;
3690 tea5757_write(btv, 5 * freq + 0x358); /* write 0x1ed8 */
3691 if (0x1ed8 == tea5757_read(btv)) {
3692 printk("bttv%d: Terratec Active Radio Upgrade found.\n",
3695 btv->has_matchbox = 1;
3698 btv->has_matchbox = 0;
3704 /* ----------------------------------------------------------------------- */
3707 * minimal bootstrap for the WinTV/PVR -- upload altera firmware.
3709 * The hcwamc.rbf firmware file is on the Hauppauge driver CD. Have
3710 * a look at Pvr/pvr45xxx.EXE (self-extracting zip archive, can be
3711 * unpacked with unzip).
3713 #define PVR_GPIO_DELAY 10
3715 #define BTTV_ALT_DATA 0x000001
3716 #define BTTV_ALT_DCLK 0x100000
3717 #define BTTV_ALT_NCONFIG 0x800000
3719 static int __devinit pvr_altera_load(struct bttv *btv, u8 *micro, u32 microlen)
3725 gpio_inout(0xffffff,BTTV_ALT_DATA|BTTV_ALT_DCLK|BTTV_ALT_NCONFIG);
3727 udelay(PVR_GPIO_DELAY);
3729 gpio_write(BTTV_ALT_NCONFIG);
3730 udelay(PVR_GPIO_DELAY);
3732 for (n = 0; n < microlen; n++) {
3734 for (i = 0 ; i < 8 ; i++) {
3735 gpio_bits(BTTV_ALT_DCLK,0);
3737 gpio_bits(BTTV_ALT_DATA,BTTV_ALT_DATA);
3739 gpio_bits(BTTV_ALT_DATA,0);
3740 gpio_bits(BTTV_ALT_DCLK,BTTV_ALT_DCLK);
3744 gpio_bits(BTTV_ALT_DCLK,0);
3745 udelay(PVR_GPIO_DELAY);
3747 /* begin Altera init loop (Not necessary,but doesn't hurt) */
3748 for (i = 0 ; i < 30 ; i++) {
3749 gpio_bits(BTTV_ALT_DCLK,0);
3750 gpio_bits(BTTV_ALT_DCLK,BTTV_ALT_DCLK);
3752 gpio_bits(BTTV_ALT_DCLK,0);
3756 static int __devinit pvr_boot(struct bttv *btv)
3758 const struct firmware *fw_entry;
3761 rc = request_firmware(&fw_entry, "hcwamc.rbf", &btv->c.pci->dev);
3763 printk(KERN_WARNING "bttv%d: no altera firmware [via hotplug]\n",
3767 rc = pvr_altera_load(btv, fw_entry->data, fw_entry->size);
3768 printk(KERN_INFO "bttv%d: altera firmware upload %s\n",
3769 btv->c.nr, (rc < 0) ? "failed" : "ok");
3770 release_firmware(fw_entry);
3774 /* ----------------------------------------------------------------------- */
3775 /* some osprey specific stuff */
3777 static void __devinit osprey_eeprom(struct bttv *btv, const u8 ee[256])
3783 /* This code will nevery actually get called in this case.... */
3784 if (btv->c.type == BTTV_BOARD_UNKNOWN) {
3785 /* this might be an antique... check for MMAC label in eeprom */
3786 if (!strncmp(ee, "MMAC", 4)) {
3788 for (i = 0; i < 21; i++)
3790 if (checksum != ee[21])
3792 cardid = BTTV_BOARD_OSPREY1x0_848;
3793 for (i = 12; i < 21; i++)
3794 serial *= 10, serial += ee[i] - '0';
3797 unsigned short type;
3799 for (i = 4*16; i < 8*16; i += 16) {
3800 u16 checksum = ip_compute_csum(ee + i, 16);
3802 if ((checksum&0xff) + (checksum>>8) == 0xff)
3809 /* found a valid descriptor */
3810 type = be16_to_cpup((u16*)(ee+4));
3815 cardid = BTTV_BOARD_OSPREY1x0_848;
3818 cardid = BTTV_BOARD_OSPREY101_848;
3824 cardid = BTTV_BOARD_OSPREY1x0;
3828 cardid = BTTV_BOARD_OSPREY1x1;
3833 cardid = BTTV_BOARD_OSPREY1x1_SVID;
3839 cardid = BTTV_BOARD_OSPREY2xx;
3843 cardid = BTTV_BOARD_OSPREY2x0_SVID;
3846 cardid = BTTV_BOARD_OSPREY500;
3850 cardid = BTTV_BOARD_OSPREY540;
3851 /* bttv_osprey_540_init(btv); */
3856 cardid = BTTV_BOARD_OSPREY2x0;
3857 /* enable output on select control lines */
3858 gpio_inout(0xffffff,0x000303);
3861 cardid = BTTV_BOARD_OSPREY440;
3864 /* unknown...leave generic, but get serial # */
3865 printk(KERN_INFO "bttv%d: "
3866 "osprey eeprom: unknown card type 0x%04x\n",
3870 serial = be32_to_cpup((u32*)(ee+6));
3873 printk(KERN_INFO "bttv%d: osprey eeprom: card=%d '%s' serial=%u\n",
3875 cardid>0 ? bttv_tvcards[cardid].name : "Unknown", serial);
3877 if (cardid<0 || btv->c.type == cardid)
3880 /* card type isn't set correctly */
3881 if (card[btv->c.nr] < bttv_num_tvcards) {
3882 printk(KERN_WARNING "bttv%d: osprey eeprom: "
3883 "Not overriding user specified card type\n", btv->c.nr);
3885 printk(KERN_INFO "bttv%d: osprey eeprom: "
3886 "Changing card type from %d to %d\n", btv->c.nr,
3887 btv->c.type, cardid);
3888 btv->c.type = cardid;
3892 /* ----------------------------------------------------------------------- */
3893 /* AVermedia specific stuff, from bktr_card.c */
3895 static int tuner_0_table[] = {
3896 TUNER_PHILIPS_NTSC, TUNER_PHILIPS_PAL /* PAL-BG*/,
3897 TUNER_PHILIPS_PAL, TUNER_PHILIPS_PAL /* PAL-I*/,
3898 TUNER_PHILIPS_PAL, TUNER_PHILIPS_PAL,
3899 TUNER_PHILIPS_SECAM, TUNER_PHILIPS_SECAM,
3900 TUNER_PHILIPS_SECAM, TUNER_PHILIPS_PAL,
3901 TUNER_PHILIPS_FM1216ME_MK3 };
3903 static int tuner_1_table[] = {
3904 TUNER_TEMIC_NTSC, TUNER_TEMIC_PAL,
3905 TUNER_TEMIC_PAL, TUNER_TEMIC_PAL,
3906 TUNER_TEMIC_PAL, TUNER_TEMIC_PAL,
3907 TUNER_TEMIC_4012FY5, TUNER_TEMIC_4012FY5, /* TUNER_TEMIC_SECAM */
3908 TUNER_TEMIC_4012FY5, TUNER_TEMIC_PAL};
3910 static void __devinit avermedia_eeprom(struct bttv *btv)
3912 int tuner_make,tuner_tv_fm,tuner_format,tuner=0;
3914 tuner_make = (eeprom_data[0x41] & 0x7);
3915 tuner_tv_fm = (eeprom_data[0x41] & 0x18) >> 3;
3916 tuner_format = (eeprom_data[0x42] & 0xf0) >> 4;
3917 btv->has_remote = (eeprom_data[0x42] & 0x01);
3919 if (tuner_make == 0 || tuner_make == 2)
3920 if(tuner_format <=0x0a)
3921 tuner = tuner_0_table[tuner_format];
3922 if (tuner_make == 1)
3923 if(tuner_format <=9)
3924 tuner = tuner_1_table[tuner_format];
3926 if (tuner_make == 4)
3927 if(tuner_format == 0x09)
3928 tuner = TUNER_LG_NTSC_NEW_TAPC; /* TAPC-G702P */
3930 printk(KERN_INFO "bttv%d: Avermedia eeprom[0x%02x%02x]: tuner=",
3931 btv->c.nr,eeprom_data[0x41],eeprom_data[0x42]);
3933 btv->tuner_type=tuner;
3936 printk("Unknown type");
3937 printk(" radio:%s remote control:%s\n",
3938 tuner_tv_fm ? "yes" : "no",
3939 btv->has_remote ? "yes" : "no");
3942 /* used on Voodoo TV/FM (Voodoo 200), S0 wired to 0x10000 */
3943 void bttv_tda9880_setnorm(struct bttv *btv, int norm)
3945 /* fix up our card entry */
3946 if(norm==V4L2_STD_NTSC) {
3947 bttv_tvcards[BTTV_BOARD_VOODOOTV_FM].gpiomux[TVAUDIO_INPUT_TUNER]=0x957fff;
3948 bttv_tvcards[BTTV_BOARD_VOODOOTV_FM].gpiomute=0x957fff;
3949 bttv_tvcards[BTTV_BOARD_VOODOOTV_200].gpiomux[TVAUDIO_INPUT_TUNER]=0x957fff;
3950 bttv_tvcards[BTTV_BOARD_VOODOOTV_200].gpiomute=0x957fff;
3951 dprintk("bttv_tda9880_setnorm to NTSC\n");
3954 bttv_tvcards[BTTV_BOARD_VOODOOTV_FM].gpiomux[TVAUDIO_INPUT_TUNER]=0x947fff;
3955 bttv_tvcards[BTTV_BOARD_VOODOOTV_FM].gpiomute=0x947fff;
3956 bttv_tvcards[BTTV_BOARD_VOODOOTV_200].gpiomux[TVAUDIO_INPUT_TUNER]=0x947fff;
3957 bttv_tvcards[BTTV_BOARD_VOODOOTV_200].gpiomute=0x947fff;
3958 dprintk("bttv_tda9880_setnorm to PAL\n");
3960 /* set GPIO according */
3961 gpio_bits(bttv_tvcards[btv->c.type].gpiomask,
3962 bttv_tvcards[btv->c.type].gpiomux[btv->audio]);
3967 * reset/enable the MSP on some Hauppauge cards
3968 * Thanks to Kyösti Mälkki (kmalkki@cc.hut.fi)!
3973 static void __devinit boot_msp34xx(struct bttv *btv, int pin)
3975 int mask = (1 << pin);
3977 gpio_inout(mask,mask);
3980 gpio_bits(mask,mask);
3983 bttv_gpio_tracking(btv,"msp34xx");
3985 printk(KERN_INFO "bttv%d: Hauppauge/Voodoo msp34xx: reset line "
3986 "init [%d]\n", btv->c.nr, pin);
3989 static void __devinit boot_bt832(struct bttv *btv)
3993 /* ----------------------------------------------------------------------- */
3994 /* Imagenation L-Model PXC200 Framegrabber */
3995 /* This is basically the same procedure as
3996 * used by Alessandro Rubini in his pxc200
3997 * driver, but using BTTV functions */
3999 static void __devinit init_PXC200(struct bttv *btv)
4001 static int vals[] __devinitdata = { 0x08, 0x09, 0x0a, 0x0b, 0x0d, 0x0d,
4002 0x01, 0x02, 0x03, 0x04, 0x05, 0x06,
4008 /* Initialise GPIO-connevted stuff */
4009 gpio_inout(0xffffff, (1<<13));
4013 /* GPIO inputs are pulled up, so no need to drive
4014 * reset pin any longer */
4015 gpio_bits(0xffffff, 0);
4017 bttv_gpio_tracking(btv,"pxc200");
4019 /* we could/should try and reset/control the AD pots? but
4020 right now we simply turned off the crushing. Without
4021 this the AGC drifts drifts
4022 remember the EN is reverse logic -->
4023 setting BT848_ADC_AGC_EN disable the AGC
4024 tboult@eecs.lehigh.edu
4027 btwrite(BT848_ADC_RESERVED|BT848_ADC_AGC_EN, BT848_ADC);
4029 /* Initialise MAX517 DAC */
4030 printk(KERN_INFO "Setting DAC reference voltage level ...\n");
4031 bttv_I2CWrite(btv,0x5E,0,0x80,1);
4033 /* Initialise 12C508 PIC */
4034 /* The I2CWrite and I2CRead commmands are actually to the
4035 * same chips - but the R/W bit is included in the address
4036 * argument so the numbers are different */
4039 printk(KERN_INFO "Initialising 12C508 PIC chip ...\n");
4041 /* First of all, enable the clock line. This is used in the PXC200-F */
4042 val = btread(BT848_GPIO_DMA_CTL);
4043 val |= BT848_GPIO_DMA_CTL_GPCLKMODE;
4044 btwrite(val, BT848_GPIO_DMA_CTL);
4046 /* Then, push to 0 the reset pin long enough to reset the *
4047 * device same as above for the reset line, but not the same
4048 * value sent to the GPIO-connected stuff
4049 * which one is the good one? */
4050 gpio_inout(0xffffff,(1<<2));
4055 for (i = 0; i < ARRAY_SIZE(vals); i++) {
4056 tmp=bttv_I2CWrite(btv,0x1E,0,vals[i],1);
4059 "I2C Write(%2.2x) = %i\nI2C Read () = %2.2x\n\n",
4060 vals[i],tmp,bttv_I2CRead(btv,0x1F,NULL));
4064 printk(KERN_INFO "PXC200 Initialised.\n");
4069 /* ----------------------------------------------------------------------- */
4071 * The Adlink RTV-24 (aka Angelo) has some special initialisation to unlock
4072 * it. This apparently involves the following procedure for each 878 chip:
4074 * 1) write 0x00C3FEFF to the GPIO_OUT_EN register
4076 * 2) write to GPIO_DATA
4082 * read from GPIO_DATA into buf (uint_32)
4083 * - if ( data>>18 & 0x01 != 0) || ( buf>>19 & 0x01 != 1 )
4084 * error. ERROR_CPLD_Check_Failed stop.
4086 * 3) write to GPIO_DATA
4087 * - write 0x4400 + 0x0E
4089 * - write 0x4410 + 0x0E
4092 * read from GPIO_DATA into buf (uint_32)
4093 * - if ( buf>>18 & 0x01 ) || ( buf>>19 & 0x01 != 0 )
4094 * error. ERROR_CPLD_Check_Failed.
4096 /* ----------------------------------------------------------------------- */
4098 init_RTV24 (struct bttv *btv)
4100 uint32_t dataRead = 0;
4101 long watchdog_value = 0x0E;
4104 "bttv%d: Adlink RTV-24 initialisation in progress ...\n",
4107 btwrite (0x00c3feff, BT848_GPIO_OUT_EN);
4109 btwrite (0 + watchdog_value, BT848_GPIO_DATA);
4111 btwrite (0x10 + watchdog_value, BT848_GPIO_DATA);
4113 btwrite (0 + watchdog_value, BT848_GPIO_DATA);
4115 dataRead = btread (BT848_GPIO_DATA);
4117 if ((((dataRead >> 18) & 0x01) != 0) || (((dataRead >> 19) & 0x01) != 1)) {
4119 "bttv%d: Adlink RTV-24 initialisation(1) ERROR_CPLD_Check_Failed (read %d)\n",
4120 btv->c.nr, dataRead);
4123 btwrite (0x4400 + watchdog_value, BT848_GPIO_DATA);
4125 btwrite (0x4410 + watchdog_value, BT848_GPIO_DATA);
4127 btwrite (watchdog_value, BT848_GPIO_DATA);
4129 dataRead = btread (BT848_GPIO_DATA);
4131 if ((((dataRead >> 18) & 0x01) != 0) || (((dataRead >> 19) & 0x01) != 0)) {
4133 "bttv%d: Adlink RTV-24 initialisation(2) ERROR_CPLD_Check_Failed (read %d)\n",
4134 btv->c.nr, dataRead);
4140 "bttv%d: Adlink RTV-24 initialisation complete.\n", btv->c.nr);
4145 /* ----------------------------------------------------------------------- */
4146 /* Miro Pro radio stuff -- the tea5757 is connected to some GPIO ports */
4148 * Copyright (c) 1999 Csaba Halasz <qgehali@uni-miskolc.hu>
4149 * This code is placed under the terms of the GNU General Public License
4151 * Brutally hacked by Dan Sheridan <dan.sheridan@contact.org.uk> djs52 8/3/00
4154 static void bus_low(struct bttv *btv, int bit)
4156 if (btv->mbox_ior) {
4157 gpio_bits(btv->mbox_ior | btv->mbox_iow | btv->mbox_csel,
4158 btv->mbox_ior | btv->mbox_iow | btv->mbox_csel);
4165 if (btv->mbox_ior) {
4166 gpio_bits(btv->mbox_iow | btv->mbox_csel, 0);
4171 static void bus_high(struct bttv *btv, int bit)
4173 if (btv->mbox_ior) {
4174 gpio_bits(btv->mbox_ior | btv->mbox_iow | btv->mbox_csel,
4175 btv->mbox_ior | btv->mbox_iow | btv->mbox_csel);
4182 if (btv->mbox_ior) {
4183 gpio_bits(btv->mbox_iow | btv->mbox_csel, 0);
4188 static int bus_in(struct bttv *btv, int bit)
4190 if (btv->mbox_ior) {
4191 gpio_bits(btv->mbox_ior | btv->mbox_iow | btv->mbox_csel,
4192 btv->mbox_ior | btv->mbox_iow | btv->mbox_csel);
4195 gpio_bits(btv->mbox_iow | btv->mbox_csel, 0);
4198 return gpio_read() & (bit);
4201 /* TEA5757 register bits */
4202 #define TEA_FREQ 0:14
4203 #define TEA_BUFFER 15:15
4205 #define TEA_SIGNAL_STRENGTH 16:17
4207 #define TEA_PORT1 18:18
4208 #define TEA_PORT0 19:19
4210 #define TEA_BAND 20:21
4211 #define TEA_BAND_FM 0
4212 #define TEA_BAND_MW 1
4213 #define TEA_BAND_LW 2
4214 #define TEA_BAND_SW 3
4216 #define TEA_MONO 22:22
4217 #define TEA_ALLOW_STEREO 0
4218 #define TEA_FORCE_MONO 1
4220 #define TEA_SEARCH_DIRECTION 23:23
4221 #define TEA_SEARCH_DOWN 0
4222 #define TEA_SEARCH_UP 1
4224 #define TEA_STATUS 24:24
4225 #define TEA_STATUS_TUNED 0
4226 #define TEA_STATUS_SEARCHING 1
4228 /* Low-level stuff */
4229 static int tea5757_read(struct bttv *btv)
4231 unsigned long timeout;
4235 /* better safe than sorry */
4236 gpio_inout(btv->mbox_mask, btv->mbox_clk | btv->mbox_we);
4238 if (btv->mbox_ior) {
4239 gpio_bits(btv->mbox_ior | btv->mbox_iow | btv->mbox_csel,
4240 btv->mbox_ior | btv->mbox_iow | btv->mbox_csel);
4245 bttv_gpio_tracking(btv,"tea5757 read");
4247 bus_low(btv,btv->mbox_we);
4248 bus_low(btv,btv->mbox_clk);
4251 timeout= jiffies + msecs_to_jiffies(1000);
4253 /* wait for DATA line to go low; error if it doesn't */
4254 while (bus_in(btv,btv->mbox_data) && time_before(jiffies, timeout))
4256 if (bus_in(btv,btv->mbox_data)) {
4257 printk(KERN_WARNING "bttv%d: tea5757: read timeout\n",btv->c.nr);
4261 dprintk("bttv%d: tea5757:",btv->c.nr);
4262 for (i = 0; i < 24; i++) {
4264 bus_high(btv,btv->mbox_clk);
4266 dprintk("%c",(bus_in(btv,btv->mbox_most) == 0)?'T':'-');
4267 bus_low(btv,btv->mbox_clk);
4269 value |= (bus_in(btv,btv->mbox_data) == 0)?0:1; /* MSB first */
4270 dprintk("%c", (bus_in(btv,btv->mbox_most) == 0)?'S':'M');
4272 dprintk("\nbttv%d: tea5757: read 0x%X\n", btv->c.nr, value);
4276 static int tea5757_write(struct bttv *btv, int value)
4281 gpio_inout(btv->mbox_mask, btv->mbox_clk | btv->mbox_we | btv->mbox_data);
4283 if (btv->mbox_ior) {
4284 gpio_bits(btv->mbox_ior | btv->mbox_iow | btv->mbox_csel,
4285 btv->mbox_ior | btv->mbox_iow | btv->mbox_csel);
4289 bttv_gpio_tracking(btv,"tea5757 write");
4291 dprintk("bttv%d: tea5757: write 0x%X\n", btv->c.nr, value);
4292 bus_low(btv,btv->mbox_clk);
4293 bus_high(btv,btv->mbox_we);
4294 for (i = 0; i < 25; i++) {
4295 if (reg & 0x1000000)
4296 bus_high(btv,btv->mbox_data);
4298 bus_low(btv,btv->mbox_data);
4300 bus_high(btv,btv->mbox_clk);
4302 bus_low(btv,btv->mbox_clk);
4305 bus_low(btv,btv->mbox_we); /* unmute !!! */
4309 void tea5757_set_freq(struct bttv *btv, unsigned short freq)
4311 dprintk("tea5757_set_freq %d\n",freq);
4312 tea5757_write(btv, 5 * freq + 0x358); /* add 10.7MHz (see docs) */
4315 /* RemoteVision MX (rv605) muxsel helper [Miguel Freitas]
4317 * This is needed because rv605 don't use a normal multiplex, but a crosspoint
4318 * switch instead (CD22M3494E). This IC can have multiple active connections
4319 * between Xn (input) and Yn (output) pins. We need to clear any existing
4320 * connection prior to establish a new one, pulsing the STROBE pin.
4322 * The board hardwire Y0 (xpoint) to MUX1 and MUXOUT to Yin.
4323 * GPIO pins are wired as:
4324 * GPIO[0:3] - AX[0:3] (xpoint) - P1[0:3] (microcontroller)
4325 * GPIO[4:6] - AY[0:2] (xpoint) - P1[4:6] (microcontroller)
4326 * GPIO[7] - DATA (xpoint) - P1[7] (microcontroller)
4327 * GPIO[8] - - P3[5] (microcontroller)
4328 * GPIO[9] - RESET (xpoint) - P3[6] (microcontroller)
4329 * GPIO[10] - STROBE (xpoint) - P3[7] (microcontroller)
4330 * GPINTR - - P3[4] (microcontroller)
4332 * The microcontroller is a 80C32 like. It should be possible to change xpoint
4333 * configuration either directly (as we are doing) or using the microcontroller
4334 * which is also wired to I2C interface. I have no further info on the
4335 * microcontroller features, one would need to disassembly the firmware.
4336 * note: the vendor refused to give any information on this product, all
4337 * that stuff was found using a multimeter! :)
4339 static void rv605_muxsel(struct bttv *btv, unsigned int input)
4341 /* reset all conections */
4342 gpio_bits(0x200,0x200);
4344 gpio_bits(0x200,0x000);
4347 /* create a new conection */
4348 gpio_bits(0x480,0x080);
4349 gpio_bits(0x480,0x480);
4351 gpio_bits(0x480,0x080);
4355 /* Tibet Systems 'Progress DVR' CS16 muxsel helper [Chris Fanning]
4357 * The CS16 (available on eBay cheap) is a PCI board with four Fusion
4358 * 878A chips, a PCI bridge, an Atmel microcontroller, four sync seperator
4359 * chips, ten eight input analog multiplexors, a not chip and a few
4362 * 16 inputs on a secondary bracket are provided and can be selected
4363 * from each of the four capture chips. Two of the eight input
4364 * multiplexors are used to select from any of the 16 input signals.
4366 * Unsupported hardware capabilities:
4367 * . A video output monitor on the secondary bracket can be selected from
4368 * one of the 878A chips.
4369 * . Another passthrough but I haven't spent any time investigating it.
4370 * . Digital I/O (logic level connected to GPIO) is available from an
4373 * The on chip input mux should always be set to 2.
4374 * GPIO[16:19] - Video input selection
4375 * GPIO[0:3] - Video output monitor select (only available from one 878A)
4376 * GPIO[?:?] - Digital I/O.
4378 * There is an ATMEL microcontroller with an 8031 core on board. I have not
4379 * determined what function (if any) it provides. With the microcontroller
4380 * and sync seperator chips a guess is that it might have to do with video
4381 * switching and maybe some digital I/O.
4383 static void tibetCS16_muxsel(struct bttv *btv, unsigned int input)
4386 gpio_bits(0x0f0000, input << 16);
4389 static void tibetCS16_init(struct bttv *btv)
4391 /* enable gpio bits, mask obtained via btSpy */
4392 gpio_inout(0xffffff, 0x0f7fff);
4393 gpio_write(0x0f7fff);
4397 * The following routines for the Kodicom-4400r get a little mind-twisting.
4398 * There is a "master" controller and three "slave" controllers, together
4399 * an analog switch which connects any of 16 cameras to any of the BT87A's.
4400 * The analog switch is controlled by the "master", but the detection order
4401 * of the four BT878A chips is in an order which I just don't understand.
4402 * The "master" is actually the second controller to be detected. The
4403 * logic on the board uses logical numbers for the 4 controllers, but
4404 * those numbers are different from the detection sequence. When working
4405 * with the analog switch, we need to "map" from the detection sequence
4406 * over to the board's logical controller number. This mapping sequence
4407 * is {3, 0, 2, 1}, i.e. the first controller to be detected is logical
4408 * unit 3, the second (which is the master) is logical unit 0, etc.
4409 * We need to maintain the status of the analog switch (which of the 16
4410 * cameras is connected to which of the 4 controllers). Rather than
4411 * add to the bttv structure for this, we use the data reserved for
4412 * the mbox (unused for this card type).
4416 * First a routine to set the analog switch, which controls which camera
4417 * is routed to which controller. The switch comprises an X-address
4418 * (gpio bits 0-3, representing the camera, ranging from 0-15), and a
4419 * Y-address (gpio bits 4-6, representing the controller, ranging from 0-3).
4420 * A data value (gpio bit 7) of '1' enables the switch, and '0' disables
4421 * the switch. A STROBE bit (gpio bit 8) latches the data value into the
4422 * specified address. The idea is to set the address and data, then bring
4423 * STROBE high, and finally bring STROBE back to low.
4425 static void kodicom4400r_write(struct bttv *btv,
4426 unsigned char xaddr,
4427 unsigned char yaddr,
4428 unsigned char data) {
4431 udata = (data << 7) | ((yaddr&3) << 4) | (xaddr&0xf);
4432 gpio_bits(0x1ff, udata); /* write ADDR and DAT */
4433 gpio_bits(0x1ff, udata | (1 << 8)); /* strobe high */
4434 gpio_bits(0x1ff, udata); /* strobe low */
4438 * Next the mux select. Both the "master" and "slave" 'cards' (controllers)
4439 * use this routine. The routine finds the "master" for the card, maps
4440 * the controller number from the detected position over to the logical
4441 * number, writes the appropriate data to the analog switch, and housekeeps
4442 * the local copy of the switch information. The parameter 'input' is the
4443 * requested camera number (0 - 15).
4445 static void kodicom4400r_muxsel(struct bttv *btv, unsigned int input)
4450 static unsigned char map[4] = {3, 0, 2, 1};
4452 mctlr = master[btv->c.nr];
4453 if (mctlr == NULL) { /* ignore if master not yet detected */
4456 yaddr = (btv->c.nr - mctlr->c.nr + 1) & 3; /* the '&' is for safety */
4458 sw_status = (char *)(&mctlr->mbox_we);
4459 xaddr = input & 0xf;
4460 /* Check if the controller/camera pair has changed, else ignore */
4461 if (sw_status[yaddr] != xaddr)
4463 /* "open" the old switch, "close" the new one, save the new */
4464 kodicom4400r_write(mctlr, sw_status[yaddr], yaddr, 0);
4465 sw_status[yaddr] = xaddr;
4466 kodicom4400r_write(mctlr, xaddr, yaddr, 1);
4471 * During initialisation, we need to reset the analog switch. We
4472 * also preset the switch to map the 4 connectors on the card to the
4473 * *user's* (see above description of kodicom4400r_muxsel) channels
4476 static void kodicom4400r_init(struct bttv *btv)
4478 char *sw_status = (char *)(&btv->mbox_we);
4481 gpio_inout(0x0003ff, 0x0003ff);
4482 gpio_write(1 << 9); /* reset MUX */
4484 /* Preset camera 0 to the 4 controllers */
4485 for (ix = 0; ix < 4; ix++) {
4487 kodicom4400r_write(btv, ix, ix, 1);
4490 * Since this is the "master", we need to set up the
4491 * other three controller chips' pointers to this structure
4492 * for later use in the muxsel routine.
4494 if ((btv->c.nr<1) || (btv->c.nr>BTTV_MAX-3))
4496 master[btv->c.nr-1] = btv;
4497 master[btv->c.nr] = btv;
4498 master[btv->c.nr+1] = btv;
4499 master[btv->c.nr+2] = btv;
4502 /* The Grandtec X-Guard framegrabber card uses two Dual 4-channel
4503 * video multiplexers to provide up to 16 video inputs. These
4504 * multiplexers are controlled by the lower 8 GPIO pins of the
4505 * bt878. The multiplexers probably Pericom PI5V331Q or similar.
4507 * xxx0 is pin xxx of multiplexer U5,
4508 * yyy1 is pin yyy of multiplexer U2
4520 static void xguard_muxsel(struct bttv *btv, unsigned int input)
4522 static const int masks[] = {
4523 ENB0, ENB0|IN00, ENB0|IN10, ENB0|IN00|IN10,
4524 ENA0, ENA0|IN00, ENA0|IN10, ENA0|IN00|IN10,
4525 ENB1, ENB1|IN01, ENB1|IN11, ENB1|IN01|IN11,
4526 ENA1, ENA1|IN01, ENA1|IN11, ENA1|IN01|IN11,
4528 gpio_write(masks[input%16]);
4530 static void picolo_tetra_init(struct bttv *btv)
4532 /*This is the video input redirection fonctionality : I DID NOT USED IT. */
4533 btwrite (0x08<<16,BT848_GPIO_DATA);/*GPIO[19] [==> 4053 B+C] set to 1 */
4534 btwrite (0x04<<16,BT848_GPIO_DATA);/*GPIO[18] [==> 4053 A] set to 1*/
4536 static void picolo_tetra_muxsel (struct bttv* btv, unsigned int input)
4539 dprintk (KERN_DEBUG "bttv%d : picolo_tetra_muxsel => input = %d\n",btv->c.nr,input);
4540 /*Just set the right path in the analog multiplexers : channel 1 -> 4 ==> Analog Mux ==> MUX0*/
4541 /*GPIO[20]&GPIO[21] used to choose the right input*/
4542 btwrite (input<<20,BT848_GPIO_DATA);
4547 * ivc120_muxsel [Added by Alan Garfield <alan@fromorbit.com>]
4549 * The IVC120G security card has 4 i2c controlled TDA8540 matrix
4550 * swichers to provide 16 channels to MUX0. The TDA8540's have
4551 * 4 independent outputs and as such the IVC120G also has the
4552 * optional "Monitor Out" bus. This allows the card to be looking
4553 * at one input while the monitor is looking at another.
4555 * Since I've couldn't be bothered figuring out how to add an
4556 * independant muxsel for the monitor bus, I've just set it to
4557 * whatever the card is looking at.
4559 * OUT0 of the TDA8540's is connected to MUX0 (0x03)
4560 * OUT1 of the TDA8540's is connected to "Monitor Out" (0x0C)
4562 * TDA8540_ALT3 IN0-3 = Channel 13 - 16 (0x03)
4563 * TDA8540_ALT4 IN0-3 = Channel 1 - 4 (0x03)
4564 * TDA8540_ALT5 IN0-3 = Channel 5 - 8 (0x03)
4565 * TDA8540_ALT6 IN0-3 = Channel 9 - 12 (0x03)
4569 /* All 7 possible sub-ids for the TDA8540 Matrix Switcher */
4570 #define I2C_TDA8540 0x90
4571 #define I2C_TDA8540_ALT1 0x92
4572 #define I2C_TDA8540_ALT2 0x94
4573 #define I2C_TDA8540_ALT3 0x96
4574 #define I2C_TDA8540_ALT4 0x98
4575 #define I2C_TDA8540_ALT5 0x9a
4576 #define I2C_TDA8540_ALT6 0x9c
4578 static void ivc120_muxsel(struct bttv *btv, unsigned int input)
4581 int key = input % 4;
4582 int matrix = input / 4;
4584 dprintk("bttv%d: ivc120_muxsel: Input - %02d | TDA - %02d | In - %02d\n",
4585 btv->c.nr, input, matrix, key);
4587 /* Handles the input selection on the TDA8540's */
4588 bttv_I2CWrite(btv, I2C_TDA8540_ALT3, 0x00,
4589 ((matrix == 3) ? (key | key << 2) : 0x00), 1);
4590 bttv_I2CWrite(btv, I2C_TDA8540_ALT4, 0x00,
4591 ((matrix == 0) ? (key | key << 2) : 0x00), 1);
4592 bttv_I2CWrite(btv, I2C_TDA8540_ALT5, 0x00,
4593 ((matrix == 1) ? (key | key << 2) : 0x00), 1);
4594 bttv_I2CWrite(btv, I2C_TDA8540_ALT6, 0x00,
4595 ((matrix == 2) ? (key | key << 2) : 0x00), 1);
4597 /* Handles the output enables on the TDA8540's */
4598 bttv_I2CWrite(btv, I2C_TDA8540_ALT3, 0x02,
4599 ((matrix == 3) ? 0x03 : 0x00), 1); /* 13 - 16 */
4600 bttv_I2CWrite(btv, I2C_TDA8540_ALT4, 0x02,
4601 ((matrix == 0) ? 0x03 : 0x00), 1); /* 1-4 */
4602 bttv_I2CWrite(btv, I2C_TDA8540_ALT5, 0x02,
4603 ((matrix == 1) ? 0x03 : 0x00), 1); /* 5-8 */
4604 bttv_I2CWrite(btv, I2C_TDA8540_ALT6, 0x02,
4605 ((matrix == 2) ? 0x03 : 0x00), 1); /* 9-12 */
4607 /* Selects MUX0 for input on the 878 */
4608 btaor((0)<<5, ~(3<<5), BT848_IFORM);
4612 /* PXC200 muxsel helper
4613 * luke@syseng.anu.edu.au
4614 * another transplant
4615 * from Alessandro Rubini (rubini@linux.it)
4617 * There are 4 kinds of cards:
4618 * PXC200L which is bt848
4619 * PXC200F which is bt848 with PIC controlling mux
4620 * PXC200AL which is bt878
4621 * PXC200AF which is bt878 with PIC controlling mux
4623 #define PX_CFG_PXC200F 0x01
4624 #define PX_FLAG_PXC200A 0x00001000 /* a pxc200A is bt-878 based */
4625 #define PX_I2C_PIC 0x0f
4626 #define PX_PXC200A_CARDID 0x200a1295
4627 #define PX_I2C_CMD_CFG 0x00
4629 static void PXC200_muxsel(struct bttv *btv, unsigned int input)
4634 unsigned char buf[2];
4636 /* Read PIC config to determine if this is a PXC200F */
4640 rc=bttv_I2CWrite(btv,(PX_I2C_PIC<<1),buf[0],buf[1],1);
4642 printk(KERN_DEBUG "bttv%d: PXC200_muxsel: pic cfg write failed:%d\n", btv->c.nr,rc);
4643 /* not PXC ? do nothing */
4647 rc=bttv_I2CRead(btv,(PX_I2C_PIC<<1),NULL);
4648 if (!(rc & PX_CFG_PXC200F)) {
4649 printk(KERN_DEBUG "bttv%d: PXC200_muxsel: not PXC200F rc:%d \n", btv->c.nr,rc);
4654 /* The multiplexer in the 200F is handled by the GPIO port */
4655 /* get correct mapping between inputs */
4656 /* mux = bttv_tvcards[btv->type].muxsel[input] & 3; */
4657 /* ** not needed!? */
4660 /* make sure output pins are enabled */
4661 /* bitmask=0x30f; */
4663 /* check whether we have a PXC200A */
4664 if (btv->cardid == PX_PXC200A_CARDID) {
4665 bitmask ^= 0x180; /* use 7 and 9, not 8 and 9 */
4666 bitmask |= 7<<4; /* the DAC */
4668 btwrite(bitmask, BT848_GPIO_OUT_EN);
4670 bitmask = btread(BT848_GPIO_DATA);
4671 if (btv->cardid == PX_PXC200A_CARDID)
4672 bitmask = (bitmask & ~0x280) | ((mux & 2) << 8) | ((mux & 1) << 7);
4673 else /* older device */
4674 bitmask = (bitmask & ~0x300) | ((mux & 3) << 8);
4675 btwrite(bitmask,BT848_GPIO_DATA);
4678 * Was "to be safe, set the bt848 to input 0"
4679 * Actually, since it's ok at load time, better not messing
4680 * with these bits (on PXC200AF you need to set mux 2 here)
4682 * needed because bttv-driver sets mux before calling this function
4684 if (btv->cardid == PX_PXC200A_CARDID)
4685 btaor(2<<5, ~BT848_IFORM_MUXSEL, BT848_IFORM);
4686 else /* older device */
4687 btand(~BT848_IFORM_MUXSEL,BT848_IFORM);
4689 printk(KERN_DEBUG "bttv%d: setting input channel to:%d\n", btv->c.nr,(int)mux);
4692 /* ----------------------------------------------------------------------- */
4693 /* motherboard chipset specific stuff */
4695 void __init bttv_check_chipset(void)
4697 int pcipci_fail = 0;
4698 struct pci_dev *dev = NULL;
4700 if (pci_pci_problems & (PCIPCI_FAIL|PCIAGP_FAIL)) /* should check if target is AGP */
4702 if (pci_pci_problems & (PCIPCI_TRITON|PCIPCI_NATOMA|PCIPCI_VIAETBF))
4704 if (pci_pci_problems & PCIPCI_VSFX)
4706 #ifdef PCIPCI_ALIMAGIK
4707 if (pci_pci_problems & PCIPCI_ALIMAGIK)
4712 /* print warnings about any quirks found */
4714 printk(KERN_INFO "bttv: Host bridge needs ETBF enabled.\n");
4716 printk(KERN_INFO "bttv: Host bridge needs VSFX enabled.\n");
4718 printk(KERN_INFO "bttv: bttv and your chipset may not work "
4721 printk(KERN_INFO "bttv: overlay will be disabled.\n");
4724 printk(KERN_INFO "bttv: overlay forced. Use this "
4725 "option at your own risk.\n");
4728 if (UNSET != latency)
4729 printk(KERN_INFO "bttv: pci latency fixup [%d]\n",latency);
4730 while ((dev = pci_get_device(PCI_VENDOR_ID_INTEL,
4731 PCI_DEVICE_ID_INTEL_82441, dev))) {
4733 pci_read_config_byte(dev, 0x53, &b);
4735 printk(KERN_INFO "bttv: Host bridge: 82441FX Natoma, "
4736 "bufcon=0x%02x\n",b);
4740 int __devinit bttv_handle_chipset(struct bttv *btv)
4742 unsigned char command;
4744 if (!triton1 && !vsfx && UNSET == latency)
4749 printk(KERN_INFO "bttv%d: enabling ETBF (430FX/VP3 compatibilty)\n",btv->c.nr);
4750 if (vsfx && btv->id >= 878)
4751 printk(KERN_INFO "bttv%d: enabling VSFX\n",btv->c.nr);
4752 if (UNSET != latency)
4753 printk(KERN_INFO "bttv%d: setting pci timer to %d\n",
4757 if (btv->id < 878) {
4758 /* bt848 (mis)uses a bit in the irq mask for etbf */
4760 btv->triton1 = BT848_INT_ETBF;
4762 /* bt878 has a bit in the pci config space for it */
4763 pci_read_config_byte(btv->c.pci, BT878_DEVCTRL, &command);
4765 command |= BT878_EN_TBFX;
4767 command |= BT878_EN_VSFX;
4768 pci_write_config_byte(btv->c.pci, BT878_DEVCTRL, command);
4770 if (UNSET != latency)
4771 pci_write_config_byte(btv->c.pci, PCI_LATENCY_TIMER, latency);
projects / linux-2.6 / blob