2 * file_storage.c -- File-backed USB Storage Gadget, for USB development
4 * Copyright (C) 2003-2005 Alan Stern
7 * Redistribution and use in source and binary forms, with or without
8 * modification, are permitted provided that the following conditions
10 * 1. Redistributions of source code must retain the above copyright
11 * notice, this list of conditions, and the following disclaimer,
12 * without modification.
13 * 2. Redistributions in binary form must reproduce the above copyright
14 * notice, this list of conditions and the following disclaimer in the
15 * documentation and/or other materials provided with the distribution.
16 * 3. The names of the above-listed copyright holders may not be used
17 * to endorse or promote products derived from this software without
18 * specific prior written permission.
20 * ALTERNATIVELY, this software may be distributed under the terms of the
21 * GNU General Public License ("GPL") as published by the Free Software
22 * Foundation, either version 2 of that License or (at your option) any
25 * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS
26 * IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO,
27 * THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR
28 * PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT OWNER OR
29 * CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL,
30 * EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO,
31 * PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR
32 * PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF
33 * LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING
34 * NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS
35 * SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
40 * The File-backed Storage Gadget acts as a USB Mass Storage device,
41 * appearing to the host as a disk drive. In addition to providing an
42 * example of a genuinely useful gadget driver for a USB device, it also
43 * illustrates a technique of double-buffering for increased throughput.
44 * Last but not least, it gives an easy way to probe the behavior of the
45 * Mass Storage drivers in a USB host.
47 * Backing storage is provided by a regular file or a block device, specified
48 * by the "file" module parameter. Access can be limited to read-only by
49 * setting the optional "ro" module parameter. The gadget will indicate that
50 * it has removable media if the optional "removable" module parameter is set.
52 * The gadget supports the Control-Bulk (CB), Control-Bulk-Interrupt (CBI),
53 * and Bulk-Only (also known as Bulk-Bulk-Bulk or BBB) transports, selected
54 * by the optional "transport" module parameter. It also supports the
55 * following protocols: RBC (0x01), ATAPI or SFF-8020i (0x02), QIC-157 (0c03),
56 * UFI (0x04), SFF-8070i (0x05), and transparent SCSI (0x06), selected by
57 * the optional "protocol" module parameter. In addition, the default
58 * Vendor ID, Product ID, and release number can be overridden.
60 * There is support for multiple logical units (LUNs), each of which has
61 * its own backing file. The number of LUNs can be set using the optional
62 * "luns" module parameter (anywhere from 1 to 8), and the corresponding
63 * files are specified using comma-separated lists for "file" and "ro".
64 * The default number of LUNs is taken from the number of "file" elements;
65 * it is 1 if "file" is not given. If "removable" is not set then a backing
66 * file must be specified for each LUN. If it is set, then an unspecified
67 * or empty backing filename means the LUN's medium is not loaded.
69 * Requirements are modest; only a bulk-in and a bulk-out endpoint are
70 * needed (an interrupt-out endpoint is also needed for CBI). The memory
71 * requirement amounts to two 16K buffers, size configurable by a parameter.
72 * Support is included for both full-speed and high-speed operation.
76 * file=filename[,filename...]
77 * Required if "removable" is not set, names of
78 * the files or block devices used for
80 * ro=b[,b...] Default false, booleans for read-only access
81 * removable Default false, boolean for removable media
82 * luns=N Default N = number of filenames, number of
84 * stall Default determined according to the type of
85 * USB device controller (usually true),
86 * boolean to permit the driver to halt
88 * transport=XXX Default BBB, transport name (CB, CBI, or BBB)
89 * protocol=YYY Default SCSI, protocol name (RBC, 8020 or
90 * ATAPI, QIC, UFI, 8070, or SCSI;
92 * vendor=0xVVVV Default 0x0525 (NetChip), USB Vendor ID
93 * product=0xPPPP Default 0xa4a5 (FSG), USB Product ID
94 * release=0xRRRR Override the USB release number (bcdDevice)
95 * buflen=N Default N=16384, buffer size used (will be
96 * rounded down to a multiple of
99 * If CONFIG_USB_FILE_STORAGE_TEST is not set, only the "file", "ro",
100 * "removable", "luns", and "stall" options are available; default values
101 * are used for everything else.
103 * The pathnames of the backing files and the ro settings are available in
104 * the attribute files "file" and "ro" in the lun<n> subdirectory of the
105 * gadget's sysfs directory. If the "removable" option is set, writing to
106 * these files will simulate ejecting/loading the medium (writing an empty
107 * line means eject) and adjusting a write-enable tab. Changes to the ro
108 * setting are not allowed when the medium is loaded.
110 * This gadget driver is heavily based on "Gadget Zero" by David Brownell.
117 * The FSG driver is fairly straightforward. There is a main kernel
118 * thread that handles most of the work. Interrupt routines field
119 * callbacks from the controller driver: bulk- and interrupt-request
120 * completion notifications, endpoint-0 events, and disconnect events.
121 * Completion events are passed to the main thread by wakeup calls. Many
122 * ep0 requests are handled at interrupt time, but SetInterface,
123 * SetConfiguration, and device reset requests are forwarded to the
124 * thread in the form of "exceptions" using SIGUSR1 signals (since they
125 * should interrupt any ongoing file I/O operations).
127 * The thread's main routine implements the standard command/data/status
128 * parts of a SCSI interaction. It and its subroutines are full of tests
129 * for pending signals/exceptions -- all this polling is necessary since
130 * the kernel has no setjmp/longjmp equivalents. (Maybe this is an
131 * indication that the driver really wants to be running in userspace.)
132 * An important point is that so long as the thread is alive it keeps an
133 * open reference to the backing file. This will prevent unmounting
134 * the backing file's underlying filesystem and could cause problems
135 * during system shutdown, for example. To prevent such problems, the
136 * thread catches INT, TERM, and KILL signals and converts them into
139 * In normal operation the main thread is started during the gadget's
140 * fsg_bind() callback and stopped during fsg_unbind(). But it can also
141 * exit when it receives a signal, and there's no point leaving the
142 * gadget running when the thread is dead. So just before the thread
143 * exits, it deregisters the gadget driver. This makes things a little
144 * tricky: The driver is deregistered at two places, and the exiting
145 * thread can indirectly call fsg_unbind() which in turn can tell the
146 * thread to exit. The first problem is resolved through the use of the
147 * REGISTERED atomic bitflag; the driver will only be deregistered once.
148 * The second problem is resolved by having fsg_unbind() check
149 * fsg->state; it won't try to stop the thread if the state is already
150 * FSG_STATE_TERMINATED.
152 * To provide maximum throughput, the driver uses a circular pipeline of
153 * buffer heads (struct fsg_buffhd). In principle the pipeline can be
154 * arbitrarily long; in practice the benefits don't justify having more
155 * than 2 stages (i.e., double buffering). But it helps to think of the
156 * pipeline as being a long one. Each buffer head contains a bulk-in and
157 * a bulk-out request pointer (since the buffer can be used for both
158 * output and input -- directions always are given from the host's
159 * point of view) as well as a pointer to the buffer and various state
162 * Use of the pipeline follows a simple protocol. There is a variable
163 * (fsg->next_buffhd_to_fill) that points to the next buffer head to use.
164 * At any time that buffer head may still be in use from an earlier
165 * request, so each buffer head has a state variable indicating whether
166 * it is EMPTY, FULL, or BUSY. Typical use involves waiting for the
167 * buffer head to be EMPTY, filling the buffer either by file I/O or by
168 * USB I/O (during which the buffer head is BUSY), and marking the buffer
169 * head FULL when the I/O is complete. Then the buffer will be emptied
170 * (again possibly by USB I/O, during which it is marked BUSY) and
171 * finally marked EMPTY again (possibly by a completion routine).
173 * A module parameter tells the driver to avoid stalling the bulk
174 * endpoints wherever the transport specification allows. This is
175 * necessary for some UDCs like the SuperH, which cannot reliably clear a
176 * halt on a bulk endpoint. However, under certain circumstances the
177 * Bulk-only specification requires a stall. In such cases the driver
178 * will halt the endpoint and set a flag indicating that it should clear
179 * the halt in software during the next device reset. Hopefully this
180 * will permit everything to work correctly. Furthermore, although the
181 * specification allows the bulk-out endpoint to halt when the host sends
182 * too much data, implementing this would cause an unavoidable race.
183 * The driver will always use the "no-stall" approach for OUT transfers.
185 * One subtle point concerns sending status-stage responses for ep0
186 * requests. Some of these requests, such as device reset, can involve
187 * interrupting an ongoing file I/O operation, which might take an
188 * arbitrarily long time. During that delay the host might give up on
189 * the original ep0 request and issue a new one. When that happens the
190 * driver should not notify the host about completion of the original
191 * request, as the host will no longer be waiting for it. So the driver
192 * assigns to each ep0 request a unique tag, and it keeps track of the
193 * tag value of the request associated with a long-running exception
194 * (device-reset, interface-change, or configuration-change). When the
195 * exception handler is finished, the status-stage response is submitted
196 * only if the current ep0 request tag is equal to the exception request
197 * tag. Thus only the most recently received ep0 request will get a
198 * status-stage response.
200 * Warning: This driver source file is too long. It ought to be split up
201 * into a header file plus about 3 separate .c files, to handle the details
202 * of the Gadget, USB Mass Storage, and SCSI protocols.
210 #include <linux/config.h>
212 #include <asm/system.h>
213 #include <asm/uaccess.h>
215 #include <linux/bitops.h>
216 #include <linux/blkdev.h>
217 #include <linux/compiler.h>
218 #include <linux/completion.h>
219 #include <linux/dcache.h>
220 #include <linux/delay.h>
221 #include <linux/device.h>
222 #include <linux/fcntl.h>
223 #include <linux/file.h>
224 #include <linux/fs.h>
225 #include <linux/init.h>
226 #include <linux/kernel.h>
227 #include <linux/kref.h>
228 #include <linux/kthread.h>
229 #include <linux/limits.h>
230 #include <linux/list.h>
231 #include <linux/module.h>
232 #include <linux/moduleparam.h>
233 #include <linux/pagemap.h>
234 #include <linux/rwsem.h>
235 #include <linux/sched.h>
236 #include <linux/signal.h>
237 #include <linux/slab.h>
238 #include <linux/spinlock.h>
239 #include <linux/string.h>
240 #include <linux/suspend.h>
241 #include <linux/utsname.h>
243 #include <linux/usb_ch9.h>
244 #include <linux/usb_gadget.h>
246 #include "gadget_chips.h"
249 /*-------------------------------------------------------------------------*/
251 #define DRIVER_DESC "File-backed Storage Gadget"
252 #define DRIVER_NAME "g_file_storage"
253 #define DRIVER_VERSION "28 November 2005"
255 static const char longname[] = DRIVER_DESC;
256 static const char shortname[] = DRIVER_NAME;
258 MODULE_DESCRIPTION(DRIVER_DESC);
259 MODULE_AUTHOR("Alan Stern");
260 MODULE_LICENSE("Dual BSD/GPL");
262 /* Thanks to NetChip Technologies for donating this product ID.
264 * DO NOT REUSE THESE IDs with any other driver!! Ever!!
265 * Instead: allocate your own, using normal USB-IF procedures. */
266 #define DRIVER_VENDOR_ID 0x0525 // NetChip
267 #define DRIVER_PRODUCT_ID 0xa4a5 // Linux-USB File-backed Storage Gadget
271 * This driver assumes self-powered hardware and has no way for users to
272 * trigger remote wakeup. It uses autoconfiguration to select endpoints
273 * and endpoint addresses.
277 /*-------------------------------------------------------------------------*/
279 #define xprintk(f,level,fmt,args...) \
280 dev_printk(level , &(f)->gadget->dev , fmt , ## args)
281 #define yprintk(l,level,fmt,args...) \
282 dev_printk(level , &(l)->dev , fmt , ## args)
285 #define DBG(fsg,fmt,args...) \
286 xprintk(fsg , KERN_DEBUG , fmt , ## args)
287 #define LDBG(lun,fmt,args...) \
288 yprintk(lun , KERN_DEBUG , fmt , ## args)
289 #define MDBG(fmt,args...) \
290 printk(KERN_DEBUG DRIVER_NAME ": " fmt , ## args)
292 #define DBG(fsg,fmt,args...) \
294 #define LDBG(lun,fmt,args...) \
296 #define MDBG(fmt,args...) \
306 #define VDBG(fsg,fmt,args...) \
308 #define VLDBG(lun,fmt,args...) \
312 #define ERROR(fsg,fmt,args...) \
313 xprintk(fsg , KERN_ERR , fmt , ## args)
314 #define LERROR(lun,fmt,args...) \
315 yprintk(lun , KERN_ERR , fmt , ## args)
317 #define WARN(fsg,fmt,args...) \
318 xprintk(fsg , KERN_WARNING , fmt , ## args)
319 #define LWARN(lun,fmt,args...) \
320 yprintk(lun , KERN_WARNING , fmt , ## args)
322 #define INFO(fsg,fmt,args...) \
323 xprintk(fsg , KERN_INFO , fmt , ## args)
324 #define LINFO(lun,fmt,args...) \
325 yprintk(lun , KERN_INFO , fmt , ## args)
327 #define MINFO(fmt,args...) \
328 printk(KERN_INFO DRIVER_NAME ": " fmt , ## args)
331 /*-------------------------------------------------------------------------*/
333 /* Encapsulate the module parameter settings */
337 /* Arggh! There should be a module_param_array_named macro! */
338 static char *file[MAX_LUNS];
339 static int ro[MAX_LUNS];
349 char *transport_parm;
351 unsigned short vendor;
352 unsigned short product;
353 unsigned short release;
357 char *transport_name;
361 } mod_data = { // Default values
362 .transport_parm = "BBB",
363 .protocol_parm = "SCSI",
366 .vendor = DRIVER_VENDOR_ID,
367 .product = DRIVER_PRODUCT_ID,
368 .release = 0xffff, // Use controller chip type
373 module_param_array(file, charp, &mod_data.num_filenames, S_IRUGO);
374 MODULE_PARM_DESC(file, "names of backing files or devices");
376 module_param_array(ro, bool, &mod_data.num_ros, S_IRUGO);
377 MODULE_PARM_DESC(ro, "true to force read-only");
379 module_param_named(luns, mod_data.nluns, uint, S_IRUGO);
380 MODULE_PARM_DESC(luns, "number of LUNs");
382 module_param_named(removable, mod_data.removable, bool, S_IRUGO);
383 MODULE_PARM_DESC(removable, "true to simulate removable media");
385 module_param_named(stall, mod_data.can_stall, bool, S_IRUGO);
386 MODULE_PARM_DESC(stall, "false to prevent bulk stalls");
389 /* In the non-TEST version, only the module parameters listed above
391 #ifdef CONFIG_USB_FILE_STORAGE_TEST
393 module_param_named(transport, mod_data.transport_parm, charp, S_IRUGO);
394 MODULE_PARM_DESC(transport, "type of transport (BBB, CBI, or CB)");
396 module_param_named(protocol, mod_data.protocol_parm, charp, S_IRUGO);
397 MODULE_PARM_DESC(protocol, "type of protocol (RBC, 8020, QIC, UFI, "
400 module_param_named(vendor, mod_data.vendor, ushort, S_IRUGO);
401 MODULE_PARM_DESC(vendor, "USB Vendor ID");
403 module_param_named(product, mod_data.product, ushort, S_IRUGO);
404 MODULE_PARM_DESC(product, "USB Product ID");
406 module_param_named(release, mod_data.release, ushort, S_IRUGO);
407 MODULE_PARM_DESC(release, "USB release number");
409 module_param_named(buflen, mod_data.buflen, uint, S_IRUGO);
410 MODULE_PARM_DESC(buflen, "I/O buffer size");
412 #endif /* CONFIG_USB_FILE_STORAGE_TEST */
415 /*-------------------------------------------------------------------------*/
417 /* USB protocol value = the transport method */
418 #define USB_PR_CBI 0x00 // Control/Bulk/Interrupt
419 #define USB_PR_CB 0x01 // Control/Bulk w/o interrupt
420 #define USB_PR_BULK 0x50 // Bulk-only
422 /* USB subclass value = the protocol encapsulation */
423 #define USB_SC_RBC 0x01 // Reduced Block Commands (flash)
424 #define USB_SC_8020 0x02 // SFF-8020i, MMC-2, ATAPI (CD-ROM)
425 #define USB_SC_QIC 0x03 // QIC-157 (tape)
426 #define USB_SC_UFI 0x04 // UFI (floppy)
427 #define USB_SC_8070 0x05 // SFF-8070i (removable)
428 #define USB_SC_SCSI 0x06 // Transparent SCSI
430 /* Bulk-only data structures */
432 /* Command Block Wrapper */
433 struct bulk_cb_wrap {
434 __le32 Signature; // Contains 'USBC'
435 u32 Tag; // Unique per command id
436 __le32 DataTransferLength; // Size of the data
437 u8 Flags; // Direction in bit 7
438 u8 Lun; // LUN (normally 0)
439 u8 Length; // Of the CDB, <= MAX_COMMAND_SIZE
440 u8 CDB[16]; // Command Data Block
443 #define USB_BULK_CB_WRAP_LEN 31
444 #define USB_BULK_CB_SIG 0x43425355 // Spells out USBC
445 #define USB_BULK_IN_FLAG 0x80
447 /* Command Status Wrapper */
448 struct bulk_cs_wrap {
449 __le32 Signature; // Should = 'USBS'
450 u32 Tag; // Same as original command
451 __le32 Residue; // Amount not transferred
452 u8 Status; // See below
455 #define USB_BULK_CS_WRAP_LEN 13
456 #define USB_BULK_CS_SIG 0x53425355 // Spells out 'USBS'
457 #define USB_STATUS_PASS 0
458 #define USB_STATUS_FAIL 1
459 #define USB_STATUS_PHASE_ERROR 2
461 /* Bulk-only class specific requests */
462 #define USB_BULK_RESET_REQUEST 0xff
463 #define USB_BULK_GET_MAX_LUN_REQUEST 0xfe
466 /* CBI Interrupt data structure */
467 struct interrupt_data {
472 #define CBI_INTERRUPT_DATA_LEN 2
474 /* CBI Accept Device-Specific Command request */
475 #define USB_CBI_ADSC_REQUEST 0x00
478 #define MAX_COMMAND_SIZE 16 // Length of a SCSI Command Data Block
480 /* SCSI commands that we recognize */
481 #define SC_FORMAT_UNIT 0x04
482 #define SC_INQUIRY 0x12
483 #define SC_MODE_SELECT_6 0x15
484 #define SC_MODE_SELECT_10 0x55
485 #define SC_MODE_SENSE_6 0x1a
486 #define SC_MODE_SENSE_10 0x5a
487 #define SC_PREVENT_ALLOW_MEDIUM_REMOVAL 0x1e
488 #define SC_READ_6 0x08
489 #define SC_READ_10 0x28
490 #define SC_READ_12 0xa8
491 #define SC_READ_CAPACITY 0x25
492 #define SC_READ_FORMAT_CAPACITIES 0x23
493 #define SC_RELEASE 0x17
494 #define SC_REQUEST_SENSE 0x03
495 #define SC_RESERVE 0x16
496 #define SC_SEND_DIAGNOSTIC 0x1d
497 #define SC_START_STOP_UNIT 0x1b
498 #define SC_SYNCHRONIZE_CACHE 0x35
499 #define SC_TEST_UNIT_READY 0x00
500 #define SC_VERIFY 0x2f
501 #define SC_WRITE_6 0x0a
502 #define SC_WRITE_10 0x2a
503 #define SC_WRITE_12 0xaa
505 /* SCSI Sense Key/Additional Sense Code/ASC Qualifier values */
506 #define SS_NO_SENSE 0
507 #define SS_COMMUNICATION_FAILURE 0x040800
508 #define SS_INVALID_COMMAND 0x052000
509 #define SS_INVALID_FIELD_IN_CDB 0x052400
510 #define SS_LOGICAL_BLOCK_ADDRESS_OUT_OF_RANGE 0x052100
511 #define SS_LOGICAL_UNIT_NOT_SUPPORTED 0x052500
512 #define SS_MEDIUM_NOT_PRESENT 0x023a00
513 #define SS_MEDIUM_REMOVAL_PREVENTED 0x055302
514 #define SS_NOT_READY_TO_READY_TRANSITION 0x062800
515 #define SS_RESET_OCCURRED 0x062900
516 #define SS_SAVING_PARAMETERS_NOT_SUPPORTED 0x053900
517 #define SS_UNRECOVERED_READ_ERROR 0x031100
518 #define SS_WRITE_ERROR 0x030c02
519 #define SS_WRITE_PROTECTED 0x072700
521 #define SK(x) ((u8) ((x) >> 16)) // Sense Key byte, etc.
522 #define ASC(x) ((u8) ((x) >> 8))
523 #define ASCQ(x) ((u8) (x))
526 /*-------------------------------------------------------------------------*/
529 * These definitions will permit the compiler to avoid generating code for
530 * parts of the driver that aren't used in the non-TEST version. Even gcc
531 * can recognize when a test of a constant expression yields a dead code
535 #ifdef CONFIG_USB_FILE_STORAGE_TEST
537 #define transport_is_bbb() (mod_data.transport_type == USB_PR_BULK)
538 #define transport_is_cbi() (mod_data.transport_type == USB_PR_CBI)
539 #define protocol_is_scsi() (mod_data.protocol_type == USB_SC_SCSI)
543 #define transport_is_bbb() 1
544 #define transport_is_cbi() 0
545 #define protocol_is_scsi() 1
547 #endif /* CONFIG_USB_FILE_STORAGE_TEST */
556 unsigned int prevent_medium_removal : 1;
557 unsigned int registered : 1;
561 u32 unit_attention_data;
566 #define backing_file_is_open(curlun) ((curlun)->filp != NULL)
568 static inline struct lun *dev_to_lun(struct device *dev)
570 return container_of(dev, struct lun, dev);
574 /* Big enough to hold our biggest descriptor */
575 #define EP0_BUFSIZE 256
576 #define DELAYED_STATUS (EP0_BUFSIZE + 999) // An impossibly large value
578 /* Number of buffers we will use. 2 is enough for double-buffering */
579 #define NUM_BUFFERS 2
581 enum fsg_buffer_state {
590 enum fsg_buffer_state state;
591 struct fsg_buffhd *next;
593 /* The NetChip 2280 is faster, and handles some protocol faults
594 * better, if we don't submit any short bulk-out read requests.
595 * So we will record the intended request length here. */
596 unsigned int bulk_out_intended_length;
598 struct usb_request *inreq;
600 struct usb_request *outreq;
605 FSG_STATE_COMMAND_PHASE = -10, // This one isn't used anywhere
606 FSG_STATE_DATA_PHASE,
607 FSG_STATE_STATUS_PHASE,
610 FSG_STATE_ABORT_BULK_OUT,
612 FSG_STATE_INTERFACE_CHANGE,
613 FSG_STATE_CONFIG_CHANGE,
614 FSG_STATE_DISCONNECT,
619 enum data_direction {
620 DATA_DIR_UNKNOWN = 0,
627 /* lock protects: state, all the req_busy's, and cbbuf_cmnd */
629 struct usb_gadget *gadget;
631 /* filesem protects: backing files in use */
632 struct rw_semaphore filesem;
634 /* reference counting: wait until all LUNs are released */
637 struct usb_ep *ep0; // Handy copy of gadget->ep0
638 struct usb_request *ep0req; // For control responses
639 unsigned int ep0_req_tag;
640 const char *ep0req_name;
642 struct usb_request *intreq; // For interrupt responses
644 struct fsg_buffhd *intr_buffhd;
646 unsigned int bulk_out_maxpacket;
647 enum fsg_state state; // For exception handling
648 unsigned int exception_req_tag;
650 u8 config, new_config;
652 unsigned int running : 1;
653 unsigned int bulk_in_enabled : 1;
654 unsigned int bulk_out_enabled : 1;
655 unsigned int intr_in_enabled : 1;
656 unsigned int phase_error : 1;
657 unsigned int short_packet_received : 1;
658 unsigned int bad_lun_okay : 1;
660 unsigned long atomic_bitflags;
662 #define CLEAR_BULK_HALTS 1
665 struct usb_ep *bulk_in;
666 struct usb_ep *bulk_out;
667 struct usb_ep *intr_in;
669 struct fsg_buffhd *next_buffhd_to_fill;
670 struct fsg_buffhd *next_buffhd_to_drain;
671 struct fsg_buffhd buffhds[NUM_BUFFERS];
673 int thread_wakeup_needed;
674 struct completion thread_notifier;
675 struct task_struct *thread_task;
676 sigset_t thread_signal_mask;
679 u8 cmnd[MAX_COMMAND_SIZE];
680 enum data_direction data_dir;
682 u32 data_size_from_cmnd;
688 /* The CB protocol offers no way for a host to know when a command
689 * has completed. As a result the next command may arrive early,
690 * and we will still have to handle it. For that reason we need
691 * a buffer to store new commands when using CB (or CBI, which
692 * does not oblige a host to wait for command completion either). */
694 u8 cbbuf_cmnd[MAX_COMMAND_SIZE];
701 typedef void (*fsg_routine_t)(struct fsg_dev *);
703 static int inline exception_in_progress(struct fsg_dev *fsg)
705 return (fsg->state > FSG_STATE_IDLE);
708 /* Make bulk-out requests be divisible by the maxpacket size */
709 static void inline set_bulk_out_req_length(struct fsg_dev *fsg,
710 struct fsg_buffhd *bh, unsigned int length)
714 bh->bulk_out_intended_length = length;
715 rem = length % fsg->bulk_out_maxpacket;
717 length += fsg->bulk_out_maxpacket - rem;
718 bh->outreq->length = length;
721 static struct fsg_dev *the_fsg;
722 static struct usb_gadget_driver fsg_driver;
724 static void close_backing_file(struct lun *curlun);
725 static void close_all_backing_files(struct fsg_dev *fsg);
728 /*-------------------------------------------------------------------------*/
732 static void dump_msg(struct fsg_dev *fsg, const char *label,
733 const u8 *buf, unsigned int length)
735 unsigned int start, num, i;
740 DBG(fsg, "%s, length %u:\n", label, length);
744 num = min(length, 16u);
746 for (i = 0; i < num; ++i) {
749 sprintf(p, " %02x", buf[i]);
753 printk(KERN_DEBUG "%6x: %s\n", start, line);
760 static void inline dump_cdb(struct fsg_dev *fsg)
765 static void inline dump_msg(struct fsg_dev *fsg, const char *label,
766 const u8 *buf, unsigned int length)
769 static void inline dump_cdb(struct fsg_dev *fsg)
772 char cmdbuf[3*MAX_COMMAND_SIZE + 1];
774 for (i = 0; i < fsg->cmnd_size; ++i)
775 sprintf(cmdbuf + i*3, " %02x", fsg->cmnd[i]);
776 VDBG(fsg, "SCSI CDB: %s\n", cmdbuf);
779 #endif /* DUMP_MSGS */
782 static int fsg_set_halt(struct fsg_dev *fsg, struct usb_ep *ep)
786 if (ep == fsg->bulk_in)
788 else if (ep == fsg->bulk_out)
792 DBG(fsg, "%s set halt\n", name);
793 return usb_ep_set_halt(ep);
797 /*-------------------------------------------------------------------------*/
799 /* Routines for unaligned data access */
801 static u16 inline get_be16(u8 *buf)
803 return ((u16) buf[0] << 8) | ((u16) buf[1]);
806 static u32 inline get_be32(u8 *buf)
808 return ((u32) buf[0] << 24) | ((u32) buf[1] << 16) |
809 ((u32) buf[2] << 8) | ((u32) buf[3]);
812 static void inline put_be16(u8 *buf, u16 val)
818 static void inline put_be32(u8 *buf, u32 val)
827 /*-------------------------------------------------------------------------*/
830 * DESCRIPTORS ... most are static, but strings and (full) configuration
831 * descriptors are built on demand. Also the (static) config and interface
832 * descriptors are adjusted during fsg_bind().
834 #define STRING_MANUFACTURER 1
835 #define STRING_PRODUCT 2
836 #define STRING_SERIAL 3
837 #define STRING_CONFIG 4
838 #define STRING_INTERFACE 5
840 /* There is only one configuration. */
841 #define CONFIG_VALUE 1
843 static struct usb_device_descriptor
845 .bLength = sizeof device_desc,
846 .bDescriptorType = USB_DT_DEVICE,
848 .bcdUSB = __constant_cpu_to_le16(0x0200),
849 .bDeviceClass = USB_CLASS_PER_INTERFACE,
851 /* The next three values can be overridden by module parameters */
852 .idVendor = __constant_cpu_to_le16(DRIVER_VENDOR_ID),
853 .idProduct = __constant_cpu_to_le16(DRIVER_PRODUCT_ID),
854 .bcdDevice = __constant_cpu_to_le16(0xffff),
856 .iManufacturer = STRING_MANUFACTURER,
857 .iProduct = STRING_PRODUCT,
858 .iSerialNumber = STRING_SERIAL,
859 .bNumConfigurations = 1,
862 static struct usb_config_descriptor
864 .bLength = sizeof config_desc,
865 .bDescriptorType = USB_DT_CONFIG,
867 /* wTotalLength computed by usb_gadget_config_buf() */
869 .bConfigurationValue = CONFIG_VALUE,
870 .iConfiguration = STRING_CONFIG,
871 .bmAttributes = USB_CONFIG_ATT_ONE | USB_CONFIG_ATT_SELFPOWER,
872 .bMaxPower = 1, // self-powered
875 static struct usb_otg_descriptor
877 .bLength = sizeof(otg_desc),
878 .bDescriptorType = USB_DT_OTG,
880 .bmAttributes = USB_OTG_SRP,
883 /* There is only one interface. */
885 static struct usb_interface_descriptor
887 .bLength = sizeof intf_desc,
888 .bDescriptorType = USB_DT_INTERFACE,
890 .bNumEndpoints = 2, // Adjusted during fsg_bind()
891 .bInterfaceClass = USB_CLASS_MASS_STORAGE,
892 .bInterfaceSubClass = USB_SC_SCSI, // Adjusted during fsg_bind()
893 .bInterfaceProtocol = USB_PR_BULK, // Adjusted during fsg_bind()
894 .iInterface = STRING_INTERFACE,
897 /* Three full-speed endpoint descriptors: bulk-in, bulk-out,
898 * and interrupt-in. */
900 static struct usb_endpoint_descriptor
902 .bLength = USB_DT_ENDPOINT_SIZE,
903 .bDescriptorType = USB_DT_ENDPOINT,
905 .bEndpointAddress = USB_DIR_IN,
906 .bmAttributes = USB_ENDPOINT_XFER_BULK,
907 /* wMaxPacketSize set by autoconfiguration */
910 static struct usb_endpoint_descriptor
912 .bLength = USB_DT_ENDPOINT_SIZE,
913 .bDescriptorType = USB_DT_ENDPOINT,
915 .bEndpointAddress = USB_DIR_OUT,
916 .bmAttributes = USB_ENDPOINT_XFER_BULK,
917 /* wMaxPacketSize set by autoconfiguration */
920 static struct usb_endpoint_descriptor
922 .bLength = USB_DT_ENDPOINT_SIZE,
923 .bDescriptorType = USB_DT_ENDPOINT,
925 .bEndpointAddress = USB_DIR_IN,
926 .bmAttributes = USB_ENDPOINT_XFER_INT,
927 .wMaxPacketSize = __constant_cpu_to_le16(2),
928 .bInterval = 32, // frames -> 32 ms
931 static const struct usb_descriptor_header *fs_function[] = {
932 (struct usb_descriptor_header *) &otg_desc,
933 (struct usb_descriptor_header *) &intf_desc,
934 (struct usb_descriptor_header *) &fs_bulk_in_desc,
935 (struct usb_descriptor_header *) &fs_bulk_out_desc,
936 (struct usb_descriptor_header *) &fs_intr_in_desc,
939 #define FS_FUNCTION_PRE_EP_ENTRIES 2
942 #ifdef CONFIG_USB_GADGET_DUALSPEED
945 * USB 2.0 devices need to expose both high speed and full speed
946 * descriptors, unless they only run at full speed.
948 * That means alternate endpoint descriptors (bigger packets)
949 * and a "device qualifier" ... plus more construction options
950 * for the config descriptor.
952 static struct usb_qualifier_descriptor
954 .bLength = sizeof dev_qualifier,
955 .bDescriptorType = USB_DT_DEVICE_QUALIFIER,
957 .bcdUSB = __constant_cpu_to_le16(0x0200),
958 .bDeviceClass = USB_CLASS_PER_INTERFACE,
960 .bNumConfigurations = 1,
963 static struct usb_endpoint_descriptor
965 .bLength = USB_DT_ENDPOINT_SIZE,
966 .bDescriptorType = USB_DT_ENDPOINT,
968 /* bEndpointAddress copied from fs_bulk_in_desc during fsg_bind() */
969 .bmAttributes = USB_ENDPOINT_XFER_BULK,
970 .wMaxPacketSize = __constant_cpu_to_le16(512),
973 static struct usb_endpoint_descriptor
975 .bLength = USB_DT_ENDPOINT_SIZE,
976 .bDescriptorType = USB_DT_ENDPOINT,
978 /* bEndpointAddress copied from fs_bulk_out_desc during fsg_bind() */
979 .bmAttributes = USB_ENDPOINT_XFER_BULK,
980 .wMaxPacketSize = __constant_cpu_to_le16(512),
981 .bInterval = 1, // NAK every 1 uframe
984 static struct usb_endpoint_descriptor
986 .bLength = USB_DT_ENDPOINT_SIZE,
987 .bDescriptorType = USB_DT_ENDPOINT,
989 /* bEndpointAddress copied from fs_intr_in_desc during fsg_bind() */
990 .bmAttributes = USB_ENDPOINT_XFER_INT,
991 .wMaxPacketSize = __constant_cpu_to_le16(2),
992 .bInterval = 9, // 2**(9-1) = 256 uframes -> 32 ms
995 static const struct usb_descriptor_header *hs_function[] = {
996 (struct usb_descriptor_header *) &otg_desc,
997 (struct usb_descriptor_header *) &intf_desc,
998 (struct usb_descriptor_header *) &hs_bulk_in_desc,
999 (struct usb_descriptor_header *) &hs_bulk_out_desc,
1000 (struct usb_descriptor_header *) &hs_intr_in_desc,
1003 #define HS_FUNCTION_PRE_EP_ENTRIES 2
1005 /* Maxpacket and other transfer characteristics vary by speed. */
1006 #define ep_desc(g,fs,hs) (((g)->speed==USB_SPEED_HIGH) ? (hs) : (fs))
1010 /* If there's no high speed support, always use the full-speed descriptor. */
1011 #define ep_desc(g,fs,hs) fs
1013 #endif /* !CONFIG_USB_GADGET_DUALSPEED */
1016 /* The CBI specification limits the serial string to 12 uppercase hexadecimal
1018 static char manufacturer[64];
1019 static char serial[13];
1021 /* Static strings, in UTF-8 (for simplicity we use only ASCII characters) */
1022 static struct usb_string strings[] = {
1023 {STRING_MANUFACTURER, manufacturer},
1024 {STRING_PRODUCT, longname},
1025 {STRING_SERIAL, serial},
1026 {STRING_CONFIG, "Self-powered"},
1027 {STRING_INTERFACE, "Mass Storage"},
1031 static struct usb_gadget_strings stringtab = {
1032 .language = 0x0409, // en-us
1038 * Config descriptors must agree with the code that sets configurations
1039 * and with code managing interfaces and their altsettings. They must
1040 * also handle different speeds and other-speed requests.
1042 static int populate_config_buf(struct usb_gadget *gadget,
1043 u8 *buf, u8 type, unsigned index)
1045 #ifdef CONFIG_USB_GADGET_DUALSPEED
1046 enum usb_device_speed speed = gadget->speed;
1049 const struct usb_descriptor_header **function;
1054 #ifdef CONFIG_USB_GADGET_DUALSPEED
1055 if (type == USB_DT_OTHER_SPEED_CONFIG)
1056 speed = (USB_SPEED_FULL + USB_SPEED_HIGH) - speed;
1057 if (speed == USB_SPEED_HIGH)
1058 function = hs_function;
1061 function = fs_function;
1063 /* for now, don't advertise srp-only devices */
1064 if (!gadget->is_otg)
1067 len = usb_gadget_config_buf(&config_desc, buf, EP0_BUFSIZE, function);
1068 ((struct usb_config_descriptor *) buf)->bDescriptorType = type;
1073 /*-------------------------------------------------------------------------*/
1075 /* These routines may be called in process context or in_irq */
1077 /* Caller must hold fsg->lock */
1078 static void wakeup_thread(struct fsg_dev *fsg)
1080 /* Tell the main thread that something has happened */
1081 fsg->thread_wakeup_needed = 1;
1082 if (fsg->thread_task)
1083 wake_up_process(fsg->thread_task);
1087 static void raise_exception(struct fsg_dev *fsg, enum fsg_state new_state)
1089 unsigned long flags;
1091 /* Do nothing if a higher-priority exception is already in progress.
1092 * If a lower-or-equal priority exception is in progress, preempt it
1093 * and notify the main thread by sending it a signal. */
1094 spin_lock_irqsave(&fsg->lock, flags);
1095 if (fsg->state <= new_state) {
1096 fsg->exception_req_tag = fsg->ep0_req_tag;
1097 fsg->state = new_state;
1098 if (fsg->thread_task)
1099 send_sig_info(SIGUSR1, SEND_SIG_FORCED,
1102 spin_unlock_irqrestore(&fsg->lock, flags);
1106 /*-------------------------------------------------------------------------*/
1108 /* The disconnect callback and ep0 routines. These always run in_irq,
1109 * except that ep0_queue() is called in the main thread to acknowledge
1110 * completion of various requests: set config, set interface, and
1111 * Bulk-only device reset. */
1113 static void fsg_disconnect(struct usb_gadget *gadget)
1115 struct fsg_dev *fsg = get_gadget_data(gadget);
1117 DBG(fsg, "disconnect or port reset\n");
1118 raise_exception(fsg, FSG_STATE_DISCONNECT);
1122 static int ep0_queue(struct fsg_dev *fsg)
1126 rc = usb_ep_queue(fsg->ep0, fsg->ep0req, GFP_ATOMIC);
1127 if (rc != 0 && rc != -ESHUTDOWN) {
1129 /* We can't do much more than wait for a reset */
1130 WARN(fsg, "error in submission: %s --> %d\n",
1131 fsg->ep0->name, rc);
1136 static void ep0_complete(struct usb_ep *ep, struct usb_request *req)
1138 struct fsg_dev *fsg = (struct fsg_dev *) ep->driver_data;
1140 if (req->actual > 0)
1141 dump_msg(fsg, fsg->ep0req_name, req->buf, req->actual);
1142 if (req->status || req->actual != req->length)
1143 DBG(fsg, "%s --> %d, %u/%u\n", __FUNCTION__,
1144 req->status, req->actual, req->length);
1145 if (req->status == -ECONNRESET) // Request was cancelled
1146 usb_ep_fifo_flush(ep);
1148 if (req->status == 0 && req->context)
1149 ((fsg_routine_t) (req->context))(fsg);
1153 /*-------------------------------------------------------------------------*/
1155 /* Bulk and interrupt endpoint completion handlers.
1156 * These always run in_irq. */
1158 static void bulk_in_complete(struct usb_ep *ep, struct usb_request *req)
1160 struct fsg_dev *fsg = (struct fsg_dev *) ep->driver_data;
1161 struct fsg_buffhd *bh = (struct fsg_buffhd *) req->context;
1163 if (req->status || req->actual != req->length)
1164 DBG(fsg, "%s --> %d, %u/%u\n", __FUNCTION__,
1165 req->status, req->actual, req->length);
1166 if (req->status == -ECONNRESET) // Request was cancelled
1167 usb_ep_fifo_flush(ep);
1169 /* Hold the lock while we update the request and buffer states */
1171 spin_lock(&fsg->lock);
1173 bh->state = BUF_STATE_EMPTY;
1175 spin_unlock(&fsg->lock);
1178 static void bulk_out_complete(struct usb_ep *ep, struct usb_request *req)
1180 struct fsg_dev *fsg = (struct fsg_dev *) ep->driver_data;
1181 struct fsg_buffhd *bh = (struct fsg_buffhd *) req->context;
1183 dump_msg(fsg, "bulk-out", req->buf, req->actual);
1184 if (req->status || req->actual != bh->bulk_out_intended_length)
1185 DBG(fsg, "%s --> %d, %u/%u\n", __FUNCTION__,
1186 req->status, req->actual,
1187 bh->bulk_out_intended_length);
1188 if (req->status == -ECONNRESET) // Request was cancelled
1189 usb_ep_fifo_flush(ep);
1191 /* Hold the lock while we update the request and buffer states */
1193 spin_lock(&fsg->lock);
1194 bh->outreq_busy = 0;
1195 bh->state = BUF_STATE_FULL;
1197 spin_unlock(&fsg->lock);
1201 #ifdef CONFIG_USB_FILE_STORAGE_TEST
1202 static void intr_in_complete(struct usb_ep *ep, struct usb_request *req)
1204 struct fsg_dev *fsg = (struct fsg_dev *) ep->driver_data;
1205 struct fsg_buffhd *bh = (struct fsg_buffhd *) req->context;
1207 if (req->status || req->actual != req->length)
1208 DBG(fsg, "%s --> %d, %u/%u\n", __FUNCTION__,
1209 req->status, req->actual, req->length);
1210 if (req->status == -ECONNRESET) // Request was cancelled
1211 usb_ep_fifo_flush(ep);
1213 /* Hold the lock while we update the request and buffer states */
1215 spin_lock(&fsg->lock);
1216 fsg->intreq_busy = 0;
1217 bh->state = BUF_STATE_EMPTY;
1219 spin_unlock(&fsg->lock);
1223 static void intr_in_complete(struct usb_ep *ep, struct usb_request *req)
1225 #endif /* CONFIG_USB_FILE_STORAGE_TEST */
1228 /*-------------------------------------------------------------------------*/
1230 /* Ep0 class-specific handlers. These always run in_irq. */
1232 #ifdef CONFIG_USB_FILE_STORAGE_TEST
1233 static void received_cbi_adsc(struct fsg_dev *fsg, struct fsg_buffhd *bh)
1235 struct usb_request *req = fsg->ep0req;
1236 static u8 cbi_reset_cmnd[6] = {
1237 SC_SEND_DIAGNOSTIC, 4, 0xff, 0xff, 0xff, 0xff};
1239 /* Error in command transfer? */
1240 if (req->status || req->length != req->actual ||
1241 req->actual < 6 || req->actual > MAX_COMMAND_SIZE) {
1243 /* Not all controllers allow a protocol stall after
1244 * receiving control-out data, but we'll try anyway. */
1245 fsg_set_halt(fsg, fsg->ep0);
1246 return; // Wait for reset
1249 /* Is it the special reset command? */
1250 if (req->actual >= sizeof cbi_reset_cmnd &&
1251 memcmp(req->buf, cbi_reset_cmnd,
1252 sizeof cbi_reset_cmnd) == 0) {
1254 /* Raise an exception to stop the current operation
1255 * and reinitialize our state. */
1256 DBG(fsg, "cbi reset request\n");
1257 raise_exception(fsg, FSG_STATE_RESET);
1261 VDBG(fsg, "CB[I] accept device-specific command\n");
1262 spin_lock(&fsg->lock);
1264 /* Save the command for later */
1265 if (fsg->cbbuf_cmnd_size)
1266 WARN(fsg, "CB[I] overwriting previous command\n");
1267 fsg->cbbuf_cmnd_size = req->actual;
1268 memcpy(fsg->cbbuf_cmnd, req->buf, fsg->cbbuf_cmnd_size);
1271 spin_unlock(&fsg->lock);
1275 static void received_cbi_adsc(struct fsg_dev *fsg, struct fsg_buffhd *bh)
1277 #endif /* CONFIG_USB_FILE_STORAGE_TEST */
1280 static int class_setup_req(struct fsg_dev *fsg,
1281 const struct usb_ctrlrequest *ctrl)
1283 struct usb_request *req = fsg->ep0req;
1284 int value = -EOPNOTSUPP;
1285 u16 w_index = le16_to_cpu(ctrl->wIndex);
1286 u16 w_length = le16_to_cpu(ctrl->wLength);
1291 /* Handle Bulk-only class-specific requests */
1292 if (transport_is_bbb()) {
1293 switch (ctrl->bRequest) {
1295 case USB_BULK_RESET_REQUEST:
1296 if (ctrl->bRequestType != (USB_DIR_OUT |
1297 USB_TYPE_CLASS | USB_RECIP_INTERFACE))
1304 /* Raise an exception to stop the current operation
1305 * and reinitialize our state. */
1306 DBG(fsg, "bulk reset request\n");
1307 raise_exception(fsg, FSG_STATE_RESET);
1308 value = DELAYED_STATUS;
1311 case USB_BULK_GET_MAX_LUN_REQUEST:
1312 if (ctrl->bRequestType != (USB_DIR_IN |
1313 USB_TYPE_CLASS | USB_RECIP_INTERFACE))
1319 VDBG(fsg, "get max LUN\n");
1320 *(u8 *) req->buf = fsg->nluns - 1;
1326 /* Handle CBI class-specific requests */
1328 switch (ctrl->bRequest) {
1330 case USB_CBI_ADSC_REQUEST:
1331 if (ctrl->bRequestType != (USB_DIR_OUT |
1332 USB_TYPE_CLASS | USB_RECIP_INTERFACE))
1338 if (w_length > MAX_COMMAND_SIZE) {
1343 fsg->ep0req->context = received_cbi_adsc;
1348 if (value == -EOPNOTSUPP)
1350 "unknown class-specific control req "
1351 "%02x.%02x v%04x i%04x l%u\n",
1352 ctrl->bRequestType, ctrl->bRequest,
1353 le16_to_cpu(ctrl->wValue), w_index, w_length);
1358 /*-------------------------------------------------------------------------*/
1360 /* Ep0 standard request handlers. These always run in_irq. */
1362 static int standard_setup_req(struct fsg_dev *fsg,
1363 const struct usb_ctrlrequest *ctrl)
1365 struct usb_request *req = fsg->ep0req;
1366 int value = -EOPNOTSUPP;
1367 u16 w_index = le16_to_cpu(ctrl->wIndex);
1368 u16 w_value = le16_to_cpu(ctrl->wValue);
1370 /* Usually this just stores reply data in the pre-allocated ep0 buffer,
1371 * but config change events will also reconfigure hardware. */
1372 switch (ctrl->bRequest) {
1374 case USB_REQ_GET_DESCRIPTOR:
1375 if (ctrl->bRequestType != (USB_DIR_IN | USB_TYPE_STANDARD |
1378 switch (w_value >> 8) {
1381 VDBG(fsg, "get device descriptor\n");
1382 value = sizeof device_desc;
1383 memcpy(req->buf, &device_desc, value);
1385 #ifdef CONFIG_USB_GADGET_DUALSPEED
1386 case USB_DT_DEVICE_QUALIFIER:
1387 VDBG(fsg, "get device qualifier\n");
1388 if (!fsg->gadget->is_dualspeed)
1390 value = sizeof dev_qualifier;
1391 memcpy(req->buf, &dev_qualifier, value);
1394 case USB_DT_OTHER_SPEED_CONFIG:
1395 VDBG(fsg, "get other-speed config descriptor\n");
1396 if (!fsg->gadget->is_dualspeed)
1401 VDBG(fsg, "get configuration descriptor\n");
1402 #ifdef CONFIG_USB_GADGET_DUALSPEED
1405 value = populate_config_buf(fsg->gadget,
1412 VDBG(fsg, "get string descriptor\n");
1414 /* wIndex == language code */
1415 value = usb_gadget_get_string(&stringtab,
1416 w_value & 0xff, req->buf);
1421 /* One config, two speeds */
1422 case USB_REQ_SET_CONFIGURATION:
1423 if (ctrl->bRequestType != (USB_DIR_OUT | USB_TYPE_STANDARD |
1426 VDBG(fsg, "set configuration\n");
1427 if (w_value == CONFIG_VALUE || w_value == 0) {
1428 fsg->new_config = w_value;
1430 /* Raise an exception to wipe out previous transaction
1431 * state (queued bufs, etc) and set the new config. */
1432 raise_exception(fsg, FSG_STATE_CONFIG_CHANGE);
1433 value = DELAYED_STATUS;
1436 case USB_REQ_GET_CONFIGURATION:
1437 if (ctrl->bRequestType != (USB_DIR_IN | USB_TYPE_STANDARD |
1440 VDBG(fsg, "get configuration\n");
1441 *(u8 *) req->buf = fsg->config;
1445 case USB_REQ_SET_INTERFACE:
1446 if (ctrl->bRequestType != (USB_DIR_OUT| USB_TYPE_STANDARD |
1447 USB_RECIP_INTERFACE))
1449 if (fsg->config && w_index == 0) {
1451 /* Raise an exception to wipe out previous transaction
1452 * state (queued bufs, etc) and install the new
1453 * interface altsetting. */
1454 raise_exception(fsg, FSG_STATE_INTERFACE_CHANGE);
1455 value = DELAYED_STATUS;
1458 case USB_REQ_GET_INTERFACE:
1459 if (ctrl->bRequestType != (USB_DIR_IN | USB_TYPE_STANDARD |
1460 USB_RECIP_INTERFACE))
1468 VDBG(fsg, "get interface\n");
1469 *(u8 *) req->buf = 0;
1475 "unknown control req %02x.%02x v%04x i%04x l%u\n",
1476 ctrl->bRequestType, ctrl->bRequest,
1477 w_value, w_index, le16_to_cpu(ctrl->wLength));
1484 static int fsg_setup(struct usb_gadget *gadget,
1485 const struct usb_ctrlrequest *ctrl)
1487 struct fsg_dev *fsg = get_gadget_data(gadget);
1489 int w_length = le16_to_cpu(ctrl->wLength);
1491 ++fsg->ep0_req_tag; // Record arrival of a new request
1492 fsg->ep0req->context = NULL;
1493 fsg->ep0req->length = 0;
1494 dump_msg(fsg, "ep0-setup", (u8 *) ctrl, sizeof(*ctrl));
1496 if ((ctrl->bRequestType & USB_TYPE_MASK) == USB_TYPE_CLASS)
1497 rc = class_setup_req(fsg, ctrl);
1499 rc = standard_setup_req(fsg, ctrl);
1501 /* Respond with data/status or defer until later? */
1502 if (rc >= 0 && rc != DELAYED_STATUS) {
1503 rc = min(rc, w_length);
1504 fsg->ep0req->length = rc;
1505 fsg->ep0req->zero = rc < w_length;
1506 fsg->ep0req_name = (ctrl->bRequestType & USB_DIR_IN ?
1507 "ep0-in" : "ep0-out");
1508 rc = ep0_queue(fsg);
1511 /* Device either stalls (rc < 0) or reports success */
1516 /*-------------------------------------------------------------------------*/
1518 /* All the following routines run in process context */
1521 /* Use this for bulk or interrupt transfers, not ep0 */
1522 static void start_transfer(struct fsg_dev *fsg, struct usb_ep *ep,
1523 struct usb_request *req, int *pbusy,
1524 enum fsg_buffer_state *state)
1528 if (ep == fsg->bulk_in)
1529 dump_msg(fsg, "bulk-in", req->buf, req->length);
1530 else if (ep == fsg->intr_in)
1531 dump_msg(fsg, "intr-in", req->buf, req->length);
1533 spin_lock_irq(&fsg->lock);
1535 *state = BUF_STATE_BUSY;
1536 spin_unlock_irq(&fsg->lock);
1537 rc = usb_ep_queue(ep, req, GFP_KERNEL);
1540 *state = BUF_STATE_EMPTY;
1542 /* We can't do much more than wait for a reset */
1544 /* Note: currently the net2280 driver fails zero-length
1545 * submissions if DMA is enabled. */
1546 if (rc != -ESHUTDOWN && !(rc == -EOPNOTSUPP &&
1548 WARN(fsg, "error in submission: %s --> %d\n",
1554 static int sleep_thread(struct fsg_dev *fsg)
1558 /* Wait until a signal arrives or we are woken up */
1561 set_current_state(TASK_INTERRUPTIBLE);
1562 if (signal_pending(current)) {
1566 if (fsg->thread_wakeup_needed)
1570 __set_current_state(TASK_RUNNING);
1571 fsg->thread_wakeup_needed = 0;
1576 /*-------------------------------------------------------------------------*/
1578 static int do_read(struct fsg_dev *fsg)
1580 struct lun *curlun = fsg->curlun;
1582 struct fsg_buffhd *bh;
1585 loff_t file_offset, file_offset_tmp;
1586 unsigned int amount;
1587 unsigned int partial_page;
1590 /* Get the starting Logical Block Address and check that it's
1592 if (fsg->cmnd[0] == SC_READ_6)
1593 lba = (fsg->cmnd[1] << 16) | get_be16(&fsg->cmnd[2]);
1595 lba = get_be32(&fsg->cmnd[2]);
1597 /* We allow DPO (Disable Page Out = don't save data in the
1598 * cache) and FUA (Force Unit Access = don't read from the
1599 * cache), but we don't implement them. */
1600 if ((fsg->cmnd[1] & ~0x18) != 0) {
1601 curlun->sense_data = SS_INVALID_FIELD_IN_CDB;
1605 if (lba >= curlun->num_sectors) {
1606 curlun->sense_data = SS_LOGICAL_BLOCK_ADDRESS_OUT_OF_RANGE;
1609 file_offset = ((loff_t) lba) << 9;
1611 /* Carry out the file reads */
1612 amount_left = fsg->data_size_from_cmnd;
1613 if (unlikely(amount_left == 0))
1614 return -EIO; // No default reply
1618 /* Figure out how much we need to read:
1619 * Try to read the remaining amount.
1620 * But don't read more than the buffer size.
1621 * And don't try to read past the end of the file.
1622 * Finally, if we're not at a page boundary, don't read past
1624 * If this means reading 0 then we were asked to read past
1625 * the end of file. */
1626 amount = min((unsigned int) amount_left, mod_data.buflen);
1627 amount = min((loff_t) amount,
1628 curlun->file_length - file_offset);
1629 partial_page = file_offset & (PAGE_CACHE_SIZE - 1);
1630 if (partial_page > 0)
1631 amount = min(amount, (unsigned int) PAGE_CACHE_SIZE -
1634 /* Wait for the next buffer to become available */
1635 bh = fsg->next_buffhd_to_fill;
1636 while (bh->state != BUF_STATE_EMPTY) {
1637 if ((rc = sleep_thread(fsg)) != 0)
1641 /* If we were asked to read past the end of file,
1642 * end with an empty buffer. */
1644 curlun->sense_data =
1645 SS_LOGICAL_BLOCK_ADDRESS_OUT_OF_RANGE;
1646 curlun->sense_data_info = file_offset >> 9;
1647 bh->inreq->length = 0;
1648 bh->state = BUF_STATE_FULL;
1652 /* Perform the read */
1653 file_offset_tmp = file_offset;
1654 nread = vfs_read(curlun->filp,
1655 (char __user *) bh->buf,
1656 amount, &file_offset_tmp);
1657 VLDBG(curlun, "file read %u @ %llu -> %d\n", amount,
1658 (unsigned long long) file_offset,
1660 if (signal_pending(current))
1664 LDBG(curlun, "error in file read: %d\n",
1667 } else if (nread < amount) {
1668 LDBG(curlun, "partial file read: %d/%u\n",
1669 (int) nread, amount);
1670 nread -= (nread & 511); // Round down to a block
1672 file_offset += nread;
1673 amount_left -= nread;
1674 fsg->residue -= nread;
1675 bh->inreq->length = nread;
1676 bh->state = BUF_STATE_FULL;
1678 /* If an error occurred, report it and its position */
1679 if (nread < amount) {
1680 curlun->sense_data = SS_UNRECOVERED_READ_ERROR;
1681 curlun->sense_data_info = file_offset >> 9;
1685 if (amount_left == 0)
1686 break; // No more left to read
1688 /* Send this buffer and go read some more */
1689 bh->inreq->zero = 0;
1690 start_transfer(fsg, fsg->bulk_in, bh->inreq,
1691 &bh->inreq_busy, &bh->state);
1692 fsg->next_buffhd_to_fill = bh->next;
1695 return -EIO; // No default reply
1699 /*-------------------------------------------------------------------------*/
1701 static int do_write(struct fsg_dev *fsg)
1703 struct lun *curlun = fsg->curlun;
1705 struct fsg_buffhd *bh;
1707 u32 amount_left_to_req, amount_left_to_write;
1708 loff_t usb_offset, file_offset, file_offset_tmp;
1709 unsigned int amount;
1710 unsigned int partial_page;
1715 curlun->sense_data = SS_WRITE_PROTECTED;
1718 curlun->filp->f_flags &= ~O_SYNC; // Default is not to wait
1720 /* Get the starting Logical Block Address and check that it's
1722 if (fsg->cmnd[0] == SC_WRITE_6)
1723 lba = (fsg->cmnd[1] << 16) | get_be16(&fsg->cmnd[2]);
1725 lba = get_be32(&fsg->cmnd[2]);
1727 /* We allow DPO (Disable Page Out = don't save data in the
1728 * cache) and FUA (Force Unit Access = write directly to the
1729 * medium). We don't implement DPO; we implement FUA by
1730 * performing synchronous output. */
1731 if ((fsg->cmnd[1] & ~0x18) != 0) {
1732 curlun->sense_data = SS_INVALID_FIELD_IN_CDB;
1735 if (fsg->cmnd[1] & 0x08) // FUA
1736 curlun->filp->f_flags |= O_SYNC;
1738 if (lba >= curlun->num_sectors) {
1739 curlun->sense_data = SS_LOGICAL_BLOCK_ADDRESS_OUT_OF_RANGE;
1743 /* Carry out the file writes */
1745 file_offset = usb_offset = ((loff_t) lba) << 9;
1746 amount_left_to_req = amount_left_to_write = fsg->data_size_from_cmnd;
1748 while (amount_left_to_write > 0) {
1750 /* Queue a request for more data from the host */
1751 bh = fsg->next_buffhd_to_fill;
1752 if (bh->state == BUF_STATE_EMPTY && get_some_more) {
1754 /* Figure out how much we want to get:
1755 * Try to get the remaining amount.
1756 * But don't get more than the buffer size.
1757 * And don't try to go past the end of the file.
1758 * If we're not at a page boundary,
1759 * don't go past the next page.
1760 * If this means getting 0, then we were asked
1761 * to write past the end of file.
1762 * Finally, round down to a block boundary. */
1763 amount = min(amount_left_to_req, mod_data.buflen);
1764 amount = min((loff_t) amount, curlun->file_length -
1766 partial_page = usb_offset & (PAGE_CACHE_SIZE - 1);
1767 if (partial_page > 0)
1768 amount = min(amount,
1769 (unsigned int) PAGE_CACHE_SIZE - partial_page);
1773 curlun->sense_data =
1774 SS_LOGICAL_BLOCK_ADDRESS_OUT_OF_RANGE;
1775 curlun->sense_data_info = usb_offset >> 9;
1778 amount -= (amount & 511);
1781 /* Why were we were asked to transfer a
1787 /* Get the next buffer */
1788 usb_offset += amount;
1789 fsg->usb_amount_left -= amount;
1790 amount_left_to_req -= amount;
1791 if (amount_left_to_req == 0)
1794 /* amount is always divisible by 512, hence by
1795 * the bulk-out maxpacket size */
1796 bh->outreq->length = bh->bulk_out_intended_length =
1798 start_transfer(fsg, fsg->bulk_out, bh->outreq,
1799 &bh->outreq_busy, &bh->state);
1800 fsg->next_buffhd_to_fill = bh->next;
1804 /* Write the received data to the backing file */
1805 bh = fsg->next_buffhd_to_drain;
1806 if (bh->state == BUF_STATE_EMPTY && !get_some_more)
1807 break; // We stopped early
1808 if (bh->state == BUF_STATE_FULL) {
1810 fsg->next_buffhd_to_drain = bh->next;
1811 bh->state = BUF_STATE_EMPTY;
1813 /* Did something go wrong with the transfer? */
1814 if (bh->outreq->status != 0) {
1815 curlun->sense_data = SS_COMMUNICATION_FAILURE;
1816 curlun->sense_data_info = file_offset >> 9;
1820 amount = bh->outreq->actual;
1821 if (curlun->file_length - file_offset < amount) {
1823 "write %u @ %llu beyond end %llu\n",
1824 amount, (unsigned long long) file_offset,
1825 (unsigned long long) curlun->file_length);
1826 amount = curlun->file_length - file_offset;
1829 /* Perform the write */
1830 file_offset_tmp = file_offset;
1831 nwritten = vfs_write(curlun->filp,
1832 (char __user *) bh->buf,
1833 amount, &file_offset_tmp);
1834 VLDBG(curlun, "file write %u @ %llu -> %d\n", amount,
1835 (unsigned long long) file_offset,
1837 if (signal_pending(current))
1838 return -EINTR; // Interrupted!
1841 LDBG(curlun, "error in file write: %d\n",
1844 } else if (nwritten < amount) {
1845 LDBG(curlun, "partial file write: %d/%u\n",
1846 (int) nwritten, amount);
1847 nwritten -= (nwritten & 511);
1848 // Round down to a block
1850 file_offset += nwritten;
1851 amount_left_to_write -= nwritten;
1852 fsg->residue -= nwritten;
1854 /* If an error occurred, report it and its position */
1855 if (nwritten < amount) {
1856 curlun->sense_data = SS_WRITE_ERROR;
1857 curlun->sense_data_info = file_offset >> 9;
1861 /* Did the host decide to stop early? */
1862 if (bh->outreq->actual != bh->outreq->length) {
1863 fsg->short_packet_received = 1;
1869 /* Wait for something to happen */
1870 if ((rc = sleep_thread(fsg)) != 0)
1874 return -EIO; // No default reply
1878 /*-------------------------------------------------------------------------*/
1880 /* Sync the file data, don't bother with the metadata.
1881 * This code was copied from fs/buffer.c:sys_fdatasync(). */
1882 static int fsync_sub(struct lun *curlun)
1884 struct file *filp = curlun->filp;
1885 struct inode *inode;
1888 if (curlun->ro || !filp)
1890 if (!filp->f_op->fsync)
1893 inode = filp->f_dentry->d_inode;
1894 mutex_lock(&inode->i_mutex);
1895 current->flags |= PF_SYNCWRITE;
1896 rc = filemap_fdatawrite(inode->i_mapping);
1897 err = filp->f_op->fsync(filp, filp->f_dentry, 1);
1900 err = filemap_fdatawait(inode->i_mapping);
1903 current->flags &= ~PF_SYNCWRITE;
1904 mutex_unlock(&inode->i_mutex);
1905 VLDBG(curlun, "fdatasync -> %d\n", rc);
1909 static void fsync_all(struct fsg_dev *fsg)
1913 for (i = 0; i < fsg->nluns; ++i)
1914 fsync_sub(&fsg->luns[i]);
1917 static int do_synchronize_cache(struct fsg_dev *fsg)
1919 struct lun *curlun = fsg->curlun;
1922 /* We ignore the requested LBA and write out all file's
1923 * dirty data buffers. */
1924 rc = fsync_sub(curlun);
1926 curlun->sense_data = SS_WRITE_ERROR;
1931 /*-------------------------------------------------------------------------*/
1933 static void invalidate_sub(struct lun *curlun)
1935 struct file *filp = curlun->filp;
1936 struct inode *inode = filp->f_dentry->d_inode;
1939 rc = invalidate_inode_pages(inode->i_mapping);
1940 VLDBG(curlun, "invalidate_inode_pages -> %ld\n", rc);
1943 static int do_verify(struct fsg_dev *fsg)
1945 struct lun *curlun = fsg->curlun;
1947 u32 verification_length;
1948 struct fsg_buffhd *bh = fsg->next_buffhd_to_fill;
1949 loff_t file_offset, file_offset_tmp;
1951 unsigned int amount;
1954 /* Get the starting Logical Block Address and check that it's
1956 lba = get_be32(&fsg->cmnd[2]);
1957 if (lba >= curlun->num_sectors) {
1958 curlun->sense_data = SS_LOGICAL_BLOCK_ADDRESS_OUT_OF_RANGE;
1962 /* We allow DPO (Disable Page Out = don't save data in the
1963 * cache) but we don't implement it. */
1964 if ((fsg->cmnd[1] & ~0x10) != 0) {
1965 curlun->sense_data = SS_INVALID_FIELD_IN_CDB;
1969 verification_length = get_be16(&fsg->cmnd[7]);
1970 if (unlikely(verification_length == 0))
1971 return -EIO; // No default reply
1973 /* Prepare to carry out the file verify */
1974 amount_left = verification_length << 9;
1975 file_offset = ((loff_t) lba) << 9;
1977 /* Write out all the dirty buffers before invalidating them */
1979 if (signal_pending(current))
1982 invalidate_sub(curlun);
1983 if (signal_pending(current))
1986 /* Just try to read the requested blocks */
1987 while (amount_left > 0) {
1989 /* Figure out how much we need to read:
1990 * Try to read the remaining amount, but not more than
1992 * And don't try to read past the end of the file.
1993 * If this means reading 0 then we were asked to read
1994 * past the end of file. */
1995 amount = min((unsigned int) amount_left, mod_data.buflen);
1996 amount = min((loff_t) amount,
1997 curlun->file_length - file_offset);
1999 curlun->sense_data =
2000 SS_LOGICAL_BLOCK_ADDRESS_OUT_OF_RANGE;
2001 curlun->sense_data_info = file_offset >> 9;
2005 /* Perform the read */
2006 file_offset_tmp = file_offset;
2007 nread = vfs_read(curlun->filp,
2008 (char __user *) bh->buf,
2009 amount, &file_offset_tmp);
2010 VLDBG(curlun, "file read %u @ %llu -> %d\n", amount,
2011 (unsigned long long) file_offset,
2013 if (signal_pending(current))
2017 LDBG(curlun, "error in file verify: %d\n",
2020 } else if (nread < amount) {
2021 LDBG(curlun, "partial file verify: %d/%u\n",
2022 (int) nread, amount);
2023 nread -= (nread & 511); // Round down to a sector
2026 curlun->sense_data = SS_UNRECOVERED_READ_ERROR;
2027 curlun->sense_data_info = file_offset >> 9;
2030 file_offset += nread;
2031 amount_left -= nread;
2037 /*-------------------------------------------------------------------------*/
2039 static int do_inquiry(struct fsg_dev *fsg, struct fsg_buffhd *bh)
2041 u8 *buf = (u8 *) bh->buf;
2043 static char vendor_id[] = "Linux ";
2044 static char product_id[] = "File-Stor Gadget";
2046 if (!fsg->curlun) { // Unsupported LUNs are okay
2047 fsg->bad_lun_okay = 1;
2049 buf[0] = 0x7f; // Unsupported, no device-type
2053 memset(buf, 0, 8); // Non-removable, direct-access device
2054 if (mod_data.removable)
2056 buf[2] = 2; // ANSI SCSI level 2
2057 buf[3] = 2; // SCSI-2 INQUIRY data format
2058 buf[4] = 31; // Additional length
2059 // No special options
2060 sprintf(buf + 8, "%-8s%-16s%04x", vendor_id, product_id,
2066 static int do_request_sense(struct fsg_dev *fsg, struct fsg_buffhd *bh)
2068 struct lun *curlun = fsg->curlun;
2069 u8 *buf = (u8 *) bh->buf;
2073 * From the SCSI-2 spec., section 7.9 (Unit attention condition):
2075 * If a REQUEST SENSE command is received from an initiator
2076 * with a pending unit attention condition (before the target
2077 * generates the contingent allegiance condition), then the
2078 * target shall either:
2079 * a) report any pending sense data and preserve the unit
2080 * attention condition on the logical unit, or,
2081 * b) report the unit attention condition, may discard any
2082 * pending sense data, and clear the unit attention
2083 * condition on the logical unit for that initiator.
2085 * FSG normally uses option a); enable this code to use option b).
2088 if (curlun && curlun->unit_attention_data != SS_NO_SENSE) {
2089 curlun->sense_data = curlun->unit_attention_data;
2090 curlun->unit_attention_data = SS_NO_SENSE;
2094 if (!curlun) { // Unsupported LUNs are okay
2095 fsg->bad_lun_okay = 1;
2096 sd = SS_LOGICAL_UNIT_NOT_SUPPORTED;
2099 sd = curlun->sense_data;
2100 sdinfo = curlun->sense_data_info;
2101 curlun->sense_data = SS_NO_SENSE;
2102 curlun->sense_data_info = 0;
2106 buf[0] = 0x80 | 0x70; // Valid, current error
2108 put_be32(&buf[3], sdinfo); // Sense information
2109 buf[7] = 18 - 8; // Additional sense length
2116 static int do_read_capacity(struct fsg_dev *fsg, struct fsg_buffhd *bh)
2118 struct lun *curlun = fsg->curlun;
2119 u32 lba = get_be32(&fsg->cmnd[2]);
2120 int pmi = fsg->cmnd[8];
2121 u8 *buf = (u8 *) bh->buf;
2123 /* Check the PMI and LBA fields */
2124 if (pmi > 1 || (pmi == 0 && lba != 0)) {
2125 curlun->sense_data = SS_INVALID_FIELD_IN_CDB;
2129 put_be32(&buf[0], curlun->num_sectors - 1); // Max logical block
2130 put_be32(&buf[4], 512); // Block length
2135 static int do_mode_sense(struct fsg_dev *fsg, struct fsg_buffhd *bh)
2137 struct lun *curlun = fsg->curlun;
2138 int mscmnd = fsg->cmnd[0];
2139 u8 *buf = (u8 *) bh->buf;
2142 int changeable_values, all_pages;
2146 if ((fsg->cmnd[1] & ~0x08) != 0) { // Mask away DBD
2147 curlun->sense_data = SS_INVALID_FIELD_IN_CDB;
2150 pc = fsg->cmnd[2] >> 6;
2151 page_code = fsg->cmnd[2] & 0x3f;
2153 curlun->sense_data = SS_SAVING_PARAMETERS_NOT_SUPPORTED;
2156 changeable_values = (pc == 1);
2157 all_pages = (page_code == 0x3f);
2159 /* Write the mode parameter header. Fixed values are: default
2160 * medium type, no cache control (DPOFUA), and no block descriptors.
2161 * The only variable value is the WriteProtect bit. We will fill in
2162 * the mode data length later. */
2164 if (mscmnd == SC_MODE_SENSE_6) {
2165 buf[2] = (curlun->ro ? 0x80 : 0x00); // WP, DPOFUA
2168 } else { // SC_MODE_SENSE_10
2169 buf[3] = (curlun->ro ? 0x80 : 0x00); // WP, DPOFUA
2171 limit = 65535; // Should really be mod_data.buflen
2174 /* No block descriptors */
2176 /* The mode pages, in numerical order. The only page we support
2177 * is the Caching page. */
2178 if (page_code == 0x08 || all_pages) {
2180 buf[0] = 0x08; // Page code
2181 buf[1] = 10; // Page length
2182 memset(buf+2, 0, 10); // None of the fields are changeable
2184 if (!changeable_values) {
2185 buf[2] = 0x04; // Write cache enable,
2186 // Read cache not disabled
2187 // No cache retention priorities
2188 put_be16(&buf[4], 0xffff); // Don't disable prefetch
2189 // Minimum prefetch = 0
2190 put_be16(&buf[8], 0xffff); // Maximum prefetch
2191 put_be16(&buf[10], 0xffff); // Maximum prefetch ceiling
2196 /* Check that a valid page was requested and the mode data length
2197 * isn't too long. */
2199 if (!valid_page || len > limit) {
2200 curlun->sense_data = SS_INVALID_FIELD_IN_CDB;
2204 /* Store the mode data length */
2205 if (mscmnd == SC_MODE_SENSE_6)
2208 put_be16(buf0, len - 2);
2213 static int do_start_stop(struct fsg_dev *fsg)
2215 struct lun *curlun = fsg->curlun;
2218 if (!mod_data.removable) {
2219 curlun->sense_data = SS_INVALID_COMMAND;
2223 // int immed = fsg->cmnd[1] & 0x01;
2224 loej = fsg->cmnd[4] & 0x02;
2225 start = fsg->cmnd[4] & 0x01;
2227 #ifdef CONFIG_USB_FILE_STORAGE_TEST
2228 if ((fsg->cmnd[1] & ~0x01) != 0 || // Mask away Immed
2229 (fsg->cmnd[4] & ~0x03) != 0) { // Mask LoEj, Start
2230 curlun->sense_data = SS_INVALID_FIELD_IN_CDB;
2236 /* Are we allowed to unload the media? */
2237 if (curlun->prevent_medium_removal) {
2238 LDBG(curlun, "unload attempt prevented\n");
2239 curlun->sense_data = SS_MEDIUM_REMOVAL_PREVENTED;
2242 if (loej) { // Simulate an unload/eject
2243 up_read(&fsg->filesem);
2244 down_write(&fsg->filesem);
2245 close_backing_file(curlun);
2246 up_write(&fsg->filesem);
2247 down_read(&fsg->filesem);
2251 /* Our emulation doesn't support mounting; the medium is
2252 * available for use as soon as it is loaded. */
2253 if (!backing_file_is_open(curlun)) {
2254 curlun->sense_data = SS_MEDIUM_NOT_PRESENT;
2263 static int do_prevent_allow(struct fsg_dev *fsg)
2265 struct lun *curlun = fsg->curlun;
2268 if (!mod_data.removable) {
2269 curlun->sense_data = SS_INVALID_COMMAND;
2273 prevent = fsg->cmnd[4] & 0x01;
2274 if ((fsg->cmnd[4] & ~0x01) != 0) { // Mask away Prevent
2275 curlun->sense_data = SS_INVALID_FIELD_IN_CDB;
2279 if (curlun->prevent_medium_removal && !prevent)
2281 curlun->prevent_medium_removal = prevent;
2286 static int do_read_format_capacities(struct fsg_dev *fsg,
2287 struct fsg_buffhd *bh)
2289 struct lun *curlun = fsg->curlun;
2290 u8 *buf = (u8 *) bh->buf;
2292 buf[0] = buf[1] = buf[2] = 0;
2293 buf[3] = 8; // Only the Current/Maximum Capacity Descriptor
2296 put_be32(&buf[0], curlun->num_sectors); // Number of blocks
2297 put_be32(&buf[4], 512); // Block length
2298 buf[4] = 0x02; // Current capacity
2303 static int do_mode_select(struct fsg_dev *fsg, struct fsg_buffhd *bh)
2305 struct lun *curlun = fsg->curlun;
2307 /* We don't support MODE SELECT */
2308 curlun->sense_data = SS_INVALID_COMMAND;
2313 /*-------------------------------------------------------------------------*/
2315 static int halt_bulk_in_endpoint(struct fsg_dev *fsg)
2319 rc = fsg_set_halt(fsg, fsg->bulk_in);
2321 VDBG(fsg, "delayed bulk-in endpoint halt\n");
2323 if (rc != -EAGAIN) {
2324 WARN(fsg, "usb_ep_set_halt -> %d\n", rc);
2329 /* Wait for a short time and then try again */
2330 if (msleep_interruptible(100) != 0)
2332 rc = usb_ep_set_halt(fsg->bulk_in);
2337 static int pad_with_zeros(struct fsg_dev *fsg)
2339 struct fsg_buffhd *bh = fsg->next_buffhd_to_fill;
2340 u32 nkeep = bh->inreq->length;
2344 bh->state = BUF_STATE_EMPTY; // For the first iteration
2345 fsg->usb_amount_left = nkeep + fsg->residue;
2346 while (fsg->usb_amount_left > 0) {
2348 /* Wait for the next buffer to be free */
2349 while (bh->state != BUF_STATE_EMPTY) {
2350 if ((rc = sleep_thread(fsg)) != 0)
2354 nsend = min(fsg->usb_amount_left, (u32) mod_data.buflen);
2355 memset(bh->buf + nkeep, 0, nsend - nkeep);
2356 bh->inreq->length = nsend;
2357 bh->inreq->zero = 0;
2358 start_transfer(fsg, fsg->bulk_in, bh->inreq,
2359 &bh->inreq_busy, &bh->state);
2360 bh = fsg->next_buffhd_to_fill = bh->next;
2361 fsg->usb_amount_left -= nsend;
2367 static int throw_away_data(struct fsg_dev *fsg)
2369 struct fsg_buffhd *bh;
2373 while ((bh = fsg->next_buffhd_to_drain)->state != BUF_STATE_EMPTY ||
2374 fsg->usb_amount_left > 0) {
2376 /* Throw away the data in a filled buffer */
2377 if (bh->state == BUF_STATE_FULL) {
2379 bh->state = BUF_STATE_EMPTY;
2380 fsg->next_buffhd_to_drain = bh->next;
2382 /* A short packet or an error ends everything */
2383 if (bh->outreq->actual != bh->outreq->length ||
2384 bh->outreq->status != 0) {
2385 raise_exception(fsg, FSG_STATE_ABORT_BULK_OUT);
2391 /* Try to submit another request if we need one */
2392 bh = fsg->next_buffhd_to_fill;
2393 if (bh->state == BUF_STATE_EMPTY && fsg->usb_amount_left > 0) {
2394 amount = min(fsg->usb_amount_left,
2395 (u32) mod_data.buflen);
2397 /* amount is always divisible by 512, hence by
2398 * the bulk-out maxpacket size */
2399 bh->outreq->length = bh->bulk_out_intended_length =
2401 start_transfer(fsg, fsg->bulk_out, bh->outreq,
2402 &bh->outreq_busy, &bh->state);
2403 fsg->next_buffhd_to_fill = bh->next;
2404 fsg->usb_amount_left -= amount;
2408 /* Otherwise wait for something to happen */
2409 if ((rc = sleep_thread(fsg)) != 0)
2416 static int finish_reply(struct fsg_dev *fsg)
2418 struct fsg_buffhd *bh = fsg->next_buffhd_to_fill;
2421 switch (fsg->data_dir) {
2423 break; // Nothing to send
2425 /* If we don't know whether the host wants to read or write,
2426 * this must be CB or CBI with an unknown command. We mustn't
2427 * try to send or receive any data. So stall both bulk pipes
2428 * if we can and wait for a reset. */
2429 case DATA_DIR_UNKNOWN:
2430 if (mod_data.can_stall) {
2431 fsg_set_halt(fsg, fsg->bulk_out);
2432 rc = halt_bulk_in_endpoint(fsg);
2436 /* All but the last buffer of data must have already been sent */
2437 case DATA_DIR_TO_HOST:
2438 if (fsg->data_size == 0)
2439 ; // Nothing to send
2441 /* If there's no residue, simply send the last buffer */
2442 else if (fsg->residue == 0) {
2443 bh->inreq->zero = 0;
2444 start_transfer(fsg, fsg->bulk_in, bh->inreq,
2445 &bh->inreq_busy, &bh->state);
2446 fsg->next_buffhd_to_fill = bh->next;
2449 /* There is a residue. For CB and CBI, simply mark the end
2450 * of the data with a short packet. However, if we are
2451 * allowed to stall, there was no data at all (residue ==
2452 * data_size), and the command failed (invalid LUN or
2453 * sense data is set), then halt the bulk-in endpoint
2455 else if (!transport_is_bbb()) {
2456 if (mod_data.can_stall &&
2457 fsg->residue == fsg->data_size &&
2458 (!fsg->curlun || fsg->curlun->sense_data != SS_NO_SENSE)) {
2459 bh->state = BUF_STATE_EMPTY;
2460 rc = halt_bulk_in_endpoint(fsg);
2462 bh->inreq->zero = 1;
2463 start_transfer(fsg, fsg->bulk_in, bh->inreq,
2464 &bh->inreq_busy, &bh->state);
2465 fsg->next_buffhd_to_fill = bh->next;
2469 /* For Bulk-only, if we're allowed to stall then send the
2470 * short packet and halt the bulk-in endpoint. If we can't
2471 * stall, pad out the remaining data with 0's. */
2473 if (mod_data.can_stall) {
2474 bh->inreq->zero = 1;
2475 start_transfer(fsg, fsg->bulk_in, bh->inreq,
2476 &bh->inreq_busy, &bh->state);
2477 fsg->next_buffhd_to_fill = bh->next;
2478 rc = halt_bulk_in_endpoint(fsg);
2480 rc = pad_with_zeros(fsg);
2484 /* We have processed all we want from the data the host has sent.
2485 * There may still be outstanding bulk-out requests. */
2486 case DATA_DIR_FROM_HOST:
2487 if (fsg->residue == 0)
2488 ; // Nothing to receive
2490 /* Did the host stop sending unexpectedly early? */
2491 else if (fsg->short_packet_received) {
2492 raise_exception(fsg, FSG_STATE_ABORT_BULK_OUT);
2496 /* We haven't processed all the incoming data. Even though
2497 * we may be allowed to stall, doing so would cause a race.
2498 * The controller may already have ACK'ed all the remaining
2499 * bulk-out packets, in which case the host wouldn't see a
2500 * STALL. Not realizing the endpoint was halted, it wouldn't
2501 * clear the halt -- leading to problems later on. */
2503 else if (mod_data.can_stall) {
2504 fsg_set_halt(fsg, fsg->bulk_out);
2505 raise_exception(fsg, FSG_STATE_ABORT_BULK_OUT);
2510 /* We can't stall. Read in the excess data and throw it
2513 rc = throw_away_data(fsg);
2520 static int send_status(struct fsg_dev *fsg)
2522 struct lun *curlun = fsg->curlun;
2523 struct fsg_buffhd *bh;
2525 u8 status = USB_STATUS_PASS;
2528 /* Wait for the next buffer to become available */
2529 bh = fsg->next_buffhd_to_fill;
2530 while (bh->state != BUF_STATE_EMPTY) {
2531 if ((rc = sleep_thread(fsg)) != 0)
2536 sd = curlun->sense_data;
2537 sdinfo = curlun->sense_data_info;
2538 } else if (fsg->bad_lun_okay)
2541 sd = SS_LOGICAL_UNIT_NOT_SUPPORTED;
2543 if (fsg->phase_error) {
2544 DBG(fsg, "sending phase-error status\n");
2545 status = USB_STATUS_PHASE_ERROR;
2546 sd = SS_INVALID_COMMAND;
2547 } else if (sd != SS_NO_SENSE) {
2548 DBG(fsg, "sending command-failure status\n");
2549 status = USB_STATUS_FAIL;
2550 VDBG(fsg, " sense data: SK x%02x, ASC x%02x, ASCQ x%02x;"
2552 SK(sd), ASC(sd), ASCQ(sd), sdinfo);
2555 if (transport_is_bbb()) {
2556 struct bulk_cs_wrap *csw = (struct bulk_cs_wrap *) bh->buf;
2558 /* Store and send the Bulk-only CSW */
2559 csw->Signature = __constant_cpu_to_le32(USB_BULK_CS_SIG);
2560 csw->Tag = fsg->tag;
2561 csw->Residue = cpu_to_le32(fsg->residue);
2562 csw->Status = status;
2564 bh->inreq->length = USB_BULK_CS_WRAP_LEN;
2565 bh->inreq->zero = 0;
2566 start_transfer(fsg, fsg->bulk_in, bh->inreq,
2567 &bh->inreq_busy, &bh->state);
2569 } else if (mod_data.transport_type == USB_PR_CB) {
2571 /* Control-Bulk transport has no status phase! */
2574 } else { // USB_PR_CBI
2575 struct interrupt_data *buf = (struct interrupt_data *)
2578 /* Store and send the Interrupt data. UFI sends the ASC
2579 * and ASCQ bytes. Everything else sends a Type (which
2580 * is always 0) and the status Value. */
2581 if (mod_data.protocol_type == USB_SC_UFI) {
2582 buf->bType = ASC(sd);
2583 buf->bValue = ASCQ(sd);
2586 buf->bValue = status;
2588 fsg->intreq->length = CBI_INTERRUPT_DATA_LEN;
2590 fsg->intr_buffhd = bh; // Point to the right buffhd
2591 fsg->intreq->buf = bh->inreq->buf;
2592 fsg->intreq->dma = bh->inreq->dma;
2593 fsg->intreq->context = bh;
2594 start_transfer(fsg, fsg->intr_in, fsg->intreq,
2595 &fsg->intreq_busy, &bh->state);
2598 fsg->next_buffhd_to_fill = bh->next;
2603 /*-------------------------------------------------------------------------*/
2605 /* Check whether the command is properly formed and whether its data size
2606 * and direction agree with the values we already have. */
2607 static int check_command(struct fsg_dev *fsg, int cmnd_size,
2608 enum data_direction data_dir, unsigned int mask,
2609 int needs_medium, const char *name)
2612 int lun = fsg->cmnd[1] >> 5;
2613 static const char dirletter[4] = {'u', 'o', 'i', 'n'};
2617 /* Adjust the expected cmnd_size for protocol encapsulation padding.
2618 * Transparent SCSI doesn't pad. */
2619 if (protocol_is_scsi())
2622 /* There's some disagreement as to whether RBC pads commands or not.
2623 * We'll play it safe and accept either form. */
2624 else if (mod_data.protocol_type == USB_SC_RBC) {
2625 if (fsg->cmnd_size == 12)
2628 /* All the other protocols pad to 12 bytes */
2633 if (fsg->data_dir != DATA_DIR_UNKNOWN)
2634 sprintf(hdlen, ", H%c=%u", dirletter[(int) fsg->data_dir],
2636 VDBG(fsg, "SCSI command: %s; Dc=%d, D%c=%u; Hc=%d%s\n",
2637 name, cmnd_size, dirletter[(int) data_dir],
2638 fsg->data_size_from_cmnd, fsg->cmnd_size, hdlen);
2640 /* We can't reply at all until we know the correct data direction
2642 if (fsg->data_size_from_cmnd == 0)
2643 data_dir = DATA_DIR_NONE;
2644 if (fsg->data_dir == DATA_DIR_UNKNOWN) { // CB or CBI
2645 fsg->data_dir = data_dir;
2646 fsg->data_size = fsg->data_size_from_cmnd;
2648 } else { // Bulk-only
2649 if (fsg->data_size < fsg->data_size_from_cmnd) {
2651 /* Host data size < Device data size is a phase error.
2652 * Carry out the command, but only transfer as much
2653 * as we are allowed. */
2654 fsg->data_size_from_cmnd = fsg->data_size;
2655 fsg->phase_error = 1;
2658 fsg->residue = fsg->usb_amount_left = fsg->data_size;
2660 /* Conflicting data directions is a phase error */
2661 if (fsg->data_dir != data_dir && fsg->data_size_from_cmnd > 0) {
2662 fsg->phase_error = 1;
2666 /* Verify the length of the command itself */
2667 if (cmnd_size != fsg->cmnd_size) {
2669 /* Special case workaround: MS-Windows issues REQUEST SENSE
2670 * with cbw->Length == 12 (it should be 6). */
2671 if (fsg->cmnd[0] == SC_REQUEST_SENSE && fsg->cmnd_size == 12)
2672 cmnd_size = fsg->cmnd_size;
2674 fsg->phase_error = 1;
2679 /* Check that the LUN values are consistent */
2680 if (transport_is_bbb()) {
2681 if (fsg->lun != lun)
2682 DBG(fsg, "using LUN %d from CBW, "
2683 "not LUN %d from CDB\n",
2686 fsg->lun = lun; // Use LUN from the command
2689 if (fsg->lun >= 0 && fsg->lun < fsg->nluns) {
2690 fsg->curlun = curlun = &fsg->luns[fsg->lun];
2691 if (fsg->cmnd[0] != SC_REQUEST_SENSE) {
2692 curlun->sense_data = SS_NO_SENSE;
2693 curlun->sense_data_info = 0;
2696 fsg->curlun = curlun = NULL;
2697 fsg->bad_lun_okay = 0;
2699 /* INQUIRY and REQUEST SENSE commands are explicitly allowed
2700 * to use unsupported LUNs; all others may not. */
2701 if (fsg->cmnd[0] != SC_INQUIRY &&
2702 fsg->cmnd[0] != SC_REQUEST_SENSE) {
2703 DBG(fsg, "unsupported LUN %d\n", fsg->lun);
2708 /* If a unit attention condition exists, only INQUIRY and
2709 * REQUEST SENSE commands are allowed; anything else must fail. */
2710 if (curlun && curlun->unit_attention_data != SS_NO_SENSE &&
2711 fsg->cmnd[0] != SC_INQUIRY &&
2712 fsg->cmnd[0] != SC_REQUEST_SENSE) {
2713 curlun->sense_data = curlun->unit_attention_data;
2714 curlun->unit_attention_data = SS_NO_SENSE;
2718 /* Check that only command bytes listed in the mask are non-zero */
2719 fsg->cmnd[1] &= 0x1f; // Mask away the LUN
2720 for (i = 1; i < cmnd_size; ++i) {
2721 if (fsg->cmnd[i] && !(mask & (1 << i))) {
2723 curlun->sense_data = SS_INVALID_FIELD_IN_CDB;
2728 /* If the medium isn't mounted and the command needs to access
2729 * it, return an error. */
2730 if (curlun && !backing_file_is_open(curlun) && needs_medium) {
2731 curlun->sense_data = SS_MEDIUM_NOT_PRESENT;
2739 static int do_scsi_command(struct fsg_dev *fsg)
2741 struct fsg_buffhd *bh;
2743 int reply = -EINVAL;
2745 static char unknown[16];
2749 /* Wait for the next buffer to become available for data or status */
2750 bh = fsg->next_buffhd_to_drain = fsg->next_buffhd_to_fill;
2751 while (bh->state != BUF_STATE_EMPTY) {
2752 if ((rc = sleep_thread(fsg)) != 0)
2755 fsg->phase_error = 0;
2756 fsg->short_packet_received = 0;
2758 down_read(&fsg->filesem); // We're using the backing file
2759 switch (fsg->cmnd[0]) {
2762 fsg->data_size_from_cmnd = fsg->cmnd[4];
2763 if ((reply = check_command(fsg, 6, DATA_DIR_TO_HOST,
2766 reply = do_inquiry(fsg, bh);
2769 case SC_MODE_SELECT_6:
2770 fsg->data_size_from_cmnd = fsg->cmnd[4];
2771 if ((reply = check_command(fsg, 6, DATA_DIR_FROM_HOST,
2773 "MODE SELECT(6)")) == 0)
2774 reply = do_mode_select(fsg, bh);
2777 case SC_MODE_SELECT_10:
2778 fsg->data_size_from_cmnd = get_be16(&fsg->cmnd[7]);
2779 if ((reply = check_command(fsg, 10, DATA_DIR_FROM_HOST,
2781 "MODE SELECT(10)")) == 0)
2782 reply = do_mode_select(fsg, bh);
2785 case SC_MODE_SENSE_6:
2786 fsg->data_size_from_cmnd = fsg->cmnd[4];
2787 if ((reply = check_command(fsg, 6, DATA_DIR_TO_HOST,
2788 (1<<1) | (1<<2) | (1<<4), 0,
2789 "MODE SENSE(6)")) == 0)
2790 reply = do_mode_sense(fsg, bh);
2793 case SC_MODE_SENSE_10:
2794 fsg->data_size_from_cmnd = get_be16(&fsg->cmnd[7]);
2795 if ((reply = check_command(fsg, 10, DATA_DIR_TO_HOST,
2796 (1<<1) | (1<<2) | (3<<7), 0,
2797 "MODE SENSE(10)")) == 0)
2798 reply = do_mode_sense(fsg, bh);
2801 case SC_PREVENT_ALLOW_MEDIUM_REMOVAL:
2802 fsg->data_size_from_cmnd = 0;
2803 if ((reply = check_command(fsg, 6, DATA_DIR_NONE,
2805 "PREVENT-ALLOW MEDIUM REMOVAL")) == 0)
2806 reply = do_prevent_allow(fsg);
2811 fsg->data_size_from_cmnd = (i == 0 ? 256 : i) << 9;
2812 if ((reply = check_command(fsg, 6, DATA_DIR_TO_HOST,
2815 reply = do_read(fsg);
2819 fsg->data_size_from_cmnd = get_be16(&fsg->cmnd[7]) << 9;
2820 if ((reply = check_command(fsg, 10, DATA_DIR_TO_HOST,
2821 (1<<1) | (0xf<<2) | (3<<7), 1,
2823 reply = do_read(fsg);
2827 fsg->data_size_from_cmnd = get_be32(&fsg->cmnd[6]) << 9;
2828 if ((reply = check_command(fsg, 12, DATA_DIR_TO_HOST,
2829 (1<<1) | (0xf<<2) | (0xf<<6), 1,
2831 reply = do_read(fsg);
2834 case SC_READ_CAPACITY:
2835 fsg->data_size_from_cmnd = 8;
2836 if ((reply = check_command(fsg, 10, DATA_DIR_TO_HOST,
2837 (0xf<<2) | (1<<8), 1,
2838 "READ CAPACITY")) == 0)
2839 reply = do_read_capacity(fsg, bh);
2842 case SC_READ_FORMAT_CAPACITIES:
2843 fsg->data_size_from_cmnd = get_be16(&fsg->cmnd[7]);
2844 if ((reply = check_command(fsg, 10, DATA_DIR_TO_HOST,
2846 "READ FORMAT CAPACITIES")) == 0)
2847 reply = do_read_format_capacities(fsg, bh);
2850 case SC_REQUEST_SENSE:
2851 fsg->data_size_from_cmnd = fsg->cmnd[4];
2852 if ((reply = check_command(fsg, 6, DATA_DIR_TO_HOST,
2854 "REQUEST SENSE")) == 0)
2855 reply = do_request_sense(fsg, bh);
2858 case SC_START_STOP_UNIT:
2859 fsg->data_size_from_cmnd = 0;
2860 if ((reply = check_command(fsg, 6, DATA_DIR_NONE,
2862 "START-STOP UNIT")) == 0)
2863 reply = do_start_stop(fsg);
2866 case SC_SYNCHRONIZE_CACHE:
2867 fsg->data_size_from_cmnd = 0;
2868 if ((reply = check_command(fsg, 10, DATA_DIR_NONE,
2869 (0xf<<2) | (3<<7), 1,
2870 "SYNCHRONIZE CACHE")) == 0)
2871 reply = do_synchronize_cache(fsg);
2874 case SC_TEST_UNIT_READY:
2875 fsg->data_size_from_cmnd = 0;
2876 reply = check_command(fsg, 6, DATA_DIR_NONE,
2881 /* Although optional, this command is used by MS-Windows. We
2882 * support a minimal version: BytChk must be 0. */
2884 fsg->data_size_from_cmnd = 0;
2885 if ((reply = check_command(fsg, 10, DATA_DIR_NONE,
2886 (1<<1) | (0xf<<2) | (3<<7), 1,
2888 reply = do_verify(fsg);
2893 fsg->data_size_from_cmnd = (i == 0 ? 256 : i) << 9;
2894 if ((reply = check_command(fsg, 6, DATA_DIR_FROM_HOST,
2897 reply = do_write(fsg);
2901 fsg->data_size_from_cmnd = get_be16(&fsg->cmnd[7]) << 9;
2902 if ((reply = check_command(fsg, 10, DATA_DIR_FROM_HOST,
2903 (1<<1) | (0xf<<2) | (3<<7), 1,
2905 reply = do_write(fsg);
2909 fsg->data_size_from_cmnd = get_be32(&fsg->cmnd[6]) << 9;
2910 if ((reply = check_command(fsg, 12, DATA_DIR_FROM_HOST,
2911 (1<<1) | (0xf<<2) | (0xf<<6), 1,
2913 reply = do_write(fsg);
2916 /* Some mandatory commands that we recognize but don't implement.
2917 * They don't mean much in this setting. It's left as an exercise
2918 * for anyone interested to implement RESERVE and RELEASE in terms
2919 * of Posix locks. */
2920 case SC_FORMAT_UNIT:
2923 case SC_SEND_DIAGNOSTIC:
2927 fsg->data_size_from_cmnd = 0;
2928 sprintf(unknown, "Unknown x%02x", fsg->cmnd[0]);
2929 if ((reply = check_command(fsg, fsg->cmnd_size,
2930 DATA_DIR_UNKNOWN, 0xff, 0, unknown)) == 0) {
2931 fsg->curlun->sense_data = SS_INVALID_COMMAND;
2936 up_read(&fsg->filesem);
2938 if (reply == -EINTR || signal_pending(current))
2941 /* Set up the single reply buffer for finish_reply() */
2942 if (reply == -EINVAL)
2943 reply = 0; // Error reply length
2944 if (reply >= 0 && fsg->data_dir == DATA_DIR_TO_HOST) {
2945 reply = min((u32) reply, fsg->data_size_from_cmnd);
2946 bh->inreq->length = reply;
2947 bh->state = BUF_STATE_FULL;
2948 fsg->residue -= reply;
2949 } // Otherwise it's already set
2955 /*-------------------------------------------------------------------------*/
2957 static int received_cbw(struct fsg_dev *fsg, struct fsg_buffhd *bh)
2959 struct usb_request *req = bh->outreq;
2960 struct bulk_cb_wrap *cbw = (struct bulk_cb_wrap *) req->buf;
2962 /* Was this a real packet? */
2966 /* Is the CBW valid? */
2967 if (req->actual != USB_BULK_CB_WRAP_LEN ||
2968 cbw->Signature != __constant_cpu_to_le32(
2970 DBG(fsg, "invalid CBW: len %u sig 0x%x\n",
2972 le32_to_cpu(cbw->Signature));
2974 /* The Bulk-only spec says we MUST stall the bulk pipes!
2975 * If we want to avoid stalls, set a flag so that we will
2976 * clear the endpoint halts at the next reset. */
2977 if (!mod_data.can_stall)
2978 set_bit(CLEAR_BULK_HALTS, &fsg->atomic_bitflags);
2979 fsg_set_halt(fsg, fsg->bulk_out);
2980 halt_bulk_in_endpoint(fsg);
2984 /* Is the CBW meaningful? */
2985 if (cbw->Lun >= MAX_LUNS || cbw->Flags & ~USB_BULK_IN_FLAG ||
2986 cbw->Length < 6 || cbw->Length > MAX_COMMAND_SIZE) {
2987 DBG(fsg, "non-meaningful CBW: lun = %u, flags = 0x%x, "
2989 cbw->Lun, cbw->Flags, cbw->Length);
2991 /* We can do anything we want here, so let's stall the
2992 * bulk pipes if we are allowed to. */
2993 if (mod_data.can_stall) {
2994 fsg_set_halt(fsg, fsg->bulk_out);
2995 halt_bulk_in_endpoint(fsg);
3000 /* Save the command for later */
3001 fsg->cmnd_size = cbw->Length;
3002 memcpy(fsg->cmnd, cbw->CDB, fsg->cmnd_size);
3003 if (cbw->Flags & USB_BULK_IN_FLAG)
3004 fsg->data_dir = DATA_DIR_TO_HOST;
3006 fsg->data_dir = DATA_DIR_FROM_HOST;
3007 fsg->data_size = le32_to_cpu(cbw->DataTransferLength);
3008 if (fsg->data_size == 0)
3009 fsg->data_dir = DATA_DIR_NONE;
3010 fsg->lun = cbw->Lun;
3011 fsg->tag = cbw->Tag;
3016 static int get_next_command(struct fsg_dev *fsg)
3018 struct fsg_buffhd *bh;
3021 if (transport_is_bbb()) {
3023 /* Wait for the next buffer to become available */
3024 bh = fsg->next_buffhd_to_fill;
3025 while (bh->state != BUF_STATE_EMPTY) {
3026 if ((rc = sleep_thread(fsg)) != 0)
3030 /* Queue a request to read a Bulk-only CBW */
3031 set_bulk_out_req_length(fsg, bh, USB_BULK_CB_WRAP_LEN);
3032 start_transfer(fsg, fsg->bulk_out, bh->outreq,
3033 &bh->outreq_busy, &bh->state);
3035 /* We will drain the buffer in software, which means we
3036 * can reuse it for the next filling. No need to advance
3037 * next_buffhd_to_fill. */
3039 /* Wait for the CBW to arrive */
3040 while (bh->state != BUF_STATE_FULL) {
3041 if ((rc = sleep_thread(fsg)) != 0)
3045 rc = received_cbw(fsg, bh);
3046 bh->state = BUF_STATE_EMPTY;
3048 } else { // USB_PR_CB or USB_PR_CBI
3050 /* Wait for the next command to arrive */
3051 while (fsg->cbbuf_cmnd_size == 0) {
3052 if ((rc = sleep_thread(fsg)) != 0)
3056 /* Is the previous status interrupt request still busy?
3057 * The host is allowed to skip reading the status,
3058 * so we must cancel it. */
3059 if (fsg->intreq_busy)
3060 usb_ep_dequeue(fsg->intr_in, fsg->intreq);
3062 /* Copy the command and mark the buffer empty */
3063 fsg->data_dir = DATA_DIR_UNKNOWN;
3064 spin_lock_irq(&fsg->lock);
3065 fsg->cmnd_size = fsg->cbbuf_cmnd_size;
3066 memcpy(fsg->cmnd, fsg->cbbuf_cmnd, fsg->cmnd_size);
3067 fsg->cbbuf_cmnd_size = 0;
3068 spin_unlock_irq(&fsg->lock);
3074 /*-------------------------------------------------------------------------*/
3076 static int enable_endpoint(struct fsg_dev *fsg, struct usb_ep *ep,
3077 const struct usb_endpoint_descriptor *d)
3081 ep->driver_data = fsg;
3082 rc = usb_ep_enable(ep, d);
3084 ERROR(fsg, "can't enable %s, result %d\n", ep->name, rc);
3088 static int alloc_request(struct fsg_dev *fsg, struct usb_ep *ep,
3089 struct usb_request **preq)
3091 *preq = usb_ep_alloc_request(ep, GFP_ATOMIC);
3094 ERROR(fsg, "can't allocate request for %s\n", ep->name);
3099 * Reset interface setting and re-init endpoint state (toggle etc).
3100 * Call with altsetting < 0 to disable the interface. The only other
3101 * available altsetting is 0, which enables the interface.
3103 static int do_set_interface(struct fsg_dev *fsg, int altsetting)
3107 const struct usb_endpoint_descriptor *d;
3110 DBG(fsg, "reset interface\n");
3113 /* Deallocate the requests */
3114 for (i = 0; i < NUM_BUFFERS; ++i) {
3115 struct fsg_buffhd *bh = &fsg->buffhds[i];
3118 usb_ep_free_request(fsg->bulk_in, bh->inreq);
3122 usb_ep_free_request(fsg->bulk_out, bh->outreq);
3127 usb_ep_free_request(fsg->intr_in, fsg->intreq);
3131 /* Disable the endpoints */
3132 if (fsg->bulk_in_enabled) {
3133 usb_ep_disable(fsg->bulk_in);
3134 fsg->bulk_in_enabled = 0;
3136 if (fsg->bulk_out_enabled) {
3137 usb_ep_disable(fsg->bulk_out);
3138 fsg->bulk_out_enabled = 0;
3140 if (fsg->intr_in_enabled) {
3141 usb_ep_disable(fsg->intr_in);
3142 fsg->intr_in_enabled = 0;
3146 if (altsetting < 0 || rc != 0)
3149 DBG(fsg, "set interface %d\n", altsetting);
3151 /* Enable the endpoints */
3152 d = ep_desc(fsg->gadget, &fs_bulk_in_desc, &hs_bulk_in_desc);
3153 if ((rc = enable_endpoint(fsg, fsg->bulk_in, d)) != 0)
3155 fsg->bulk_in_enabled = 1;
3157 d = ep_desc(fsg->gadget, &fs_bulk_out_desc, &hs_bulk_out_desc);
3158 if ((rc = enable_endpoint(fsg, fsg->bulk_out, d)) != 0)
3160 fsg->bulk_out_enabled = 1;
3161 fsg->bulk_out_maxpacket = le16_to_cpu(d->wMaxPacketSize);
3163 if (transport_is_cbi()) {
3164 d = ep_desc(fsg->gadget, &fs_intr_in_desc, &hs_intr_in_desc);
3165 if ((rc = enable_endpoint(fsg, fsg->intr_in, d)) != 0)
3167 fsg->intr_in_enabled = 1;
3170 /* Allocate the requests */
3171 for (i = 0; i < NUM_BUFFERS; ++i) {
3172 struct fsg_buffhd *bh = &fsg->buffhds[i];
3174 if ((rc = alloc_request(fsg, fsg->bulk_in, &bh->inreq)) != 0)
3176 if ((rc = alloc_request(fsg, fsg->bulk_out, &bh->outreq)) != 0)
3178 bh->inreq->buf = bh->outreq->buf = bh->buf;
3179 bh->inreq->dma = bh->outreq->dma = bh->dma;
3180 bh->inreq->context = bh->outreq->context = bh;
3181 bh->inreq->complete = bulk_in_complete;
3182 bh->outreq->complete = bulk_out_complete;
3184 if (transport_is_cbi()) {
3185 if ((rc = alloc_request(fsg, fsg->intr_in, &fsg->intreq)) != 0)
3187 fsg->intreq->complete = intr_in_complete;
3191 for (i = 0; i < fsg->nluns; ++i)
3192 fsg->luns[i].unit_attention_data = SS_RESET_OCCURRED;
3198 * Change our operational configuration. This code must agree with the code
3199 * that returns config descriptors, and with interface altsetting code.
3201 * It's also responsible for power management interactions. Some
3202 * configurations might not work with our current power sources.
3203 * For now we just assume the gadget is always self-powered.
3205 static int do_set_config(struct fsg_dev *fsg, u8 new_config)
3209 /* Disable the single interface */
3210 if (fsg->config != 0) {
3211 DBG(fsg, "reset config\n");
3213 rc = do_set_interface(fsg, -1);
3216 /* Enable the interface */
3217 if (new_config != 0) {
3218 fsg->config = new_config;
3219 if ((rc = do_set_interface(fsg, 0)) != 0)
3220 fsg->config = 0; // Reset on errors
3224 switch (fsg->gadget->speed) {
3225 case USB_SPEED_LOW: speed = "low"; break;
3226 case USB_SPEED_FULL: speed = "full"; break;
3227 case USB_SPEED_HIGH: speed = "high"; break;
3228 default: speed = "?"; break;
3230 INFO(fsg, "%s speed config #%d\n", speed, fsg->config);
3237 /*-------------------------------------------------------------------------*/
3239 static void handle_exception(struct fsg_dev *fsg)
3245 struct fsg_buffhd *bh;
3246 enum fsg_state old_state;
3249 unsigned int exception_req_tag;
3252 /* Clear the existing signals. Anything but SIGUSR1 is converted
3253 * into a high-priority EXIT exception. */
3255 sig = dequeue_signal_lock(current, &fsg->thread_signal_mask,
3259 if (sig != SIGUSR1) {
3260 if (fsg->state < FSG_STATE_EXIT)
3261 DBG(fsg, "Main thread exiting on signal\n");
3262 raise_exception(fsg, FSG_STATE_EXIT);
3266 /* Cancel all the pending transfers */
3267 if (fsg->intreq_busy)
3268 usb_ep_dequeue(fsg->intr_in, fsg->intreq);
3269 for (i = 0; i < NUM_BUFFERS; ++i) {
3270 bh = &fsg->buffhds[i];
3272 usb_ep_dequeue(fsg->bulk_in, bh->inreq);
3273 if (bh->outreq_busy)
3274 usb_ep_dequeue(fsg->bulk_out, bh->outreq);
3277 /* Wait until everything is idle */
3279 num_active = fsg->intreq_busy;
3280 for (i = 0; i < NUM_BUFFERS; ++i) {
3281 bh = &fsg->buffhds[i];
3282 num_active += bh->inreq_busy + bh->outreq_busy;
3284 if (num_active == 0)
3286 if (sleep_thread(fsg))
3290 /* Clear out the controller's fifos */
3291 if (fsg->bulk_in_enabled)
3292 usb_ep_fifo_flush(fsg->bulk_in);
3293 if (fsg->bulk_out_enabled)
3294 usb_ep_fifo_flush(fsg->bulk_out);
3295 if (fsg->intr_in_enabled)
3296 usb_ep_fifo_flush(fsg->intr_in);
3298 /* Reset the I/O buffer states and pointers, the SCSI
3299 * state, and the exception. Then invoke the handler. */
3300 spin_lock_irq(&fsg->lock);
3302 for (i = 0; i < NUM_BUFFERS; ++i) {
3303 bh = &fsg->buffhds[i];
3304 bh->state = BUF_STATE_EMPTY;
3306 fsg->next_buffhd_to_fill = fsg->next_buffhd_to_drain =
3309 exception_req_tag = fsg->exception_req_tag;
3310 new_config = fsg->new_config;
3311 old_state = fsg->state;
3313 if (old_state == FSG_STATE_ABORT_BULK_OUT)
3314 fsg->state = FSG_STATE_STATUS_PHASE;
3316 for (i = 0; i < fsg->nluns; ++i) {
3317 curlun = &fsg->luns[i];
3318 curlun->prevent_medium_removal = 0;
3319 curlun->sense_data = curlun->unit_attention_data =
3321 curlun->sense_data_info = 0;
3323 fsg->state = FSG_STATE_IDLE;
3325 spin_unlock_irq(&fsg->lock);
3327 /* Carry out any extra actions required for the exception */
3328 switch (old_state) {
3332 case FSG_STATE_ABORT_BULK_OUT:
3334 spin_lock_irq(&fsg->lock);
3335 if (fsg->state == FSG_STATE_STATUS_PHASE)
3336 fsg->state = FSG_STATE_IDLE;
3337 spin_unlock_irq(&fsg->lock);
3340 case FSG_STATE_RESET:
3341 /* In case we were forced against our will to halt a
3342 * bulk endpoint, clear the halt now. (The SuperH UDC
3343 * requires this.) */
3344 if (test_and_clear_bit(CLEAR_BULK_HALTS,
3345 &fsg->atomic_bitflags)) {
3346 usb_ep_clear_halt(fsg->bulk_in);
3347 usb_ep_clear_halt(fsg->bulk_out);
3350 if (transport_is_bbb()) {
3351 if (fsg->ep0_req_tag == exception_req_tag)
3352 ep0_queue(fsg); // Complete the status stage
3354 } else if (transport_is_cbi())
3355 send_status(fsg); // Status by interrupt pipe
3357 /* Technically this should go here, but it would only be
3358 * a waste of time. Ditto for the INTERFACE_CHANGE and
3359 * CONFIG_CHANGE cases. */
3360 // for (i = 0; i < fsg->nluns; ++i)
3361 // fsg->luns[i].unit_attention_data = SS_RESET_OCCURRED;
3364 case FSG_STATE_INTERFACE_CHANGE:
3365 rc = do_set_interface(fsg, 0);
3366 if (fsg->ep0_req_tag != exception_req_tag)
3368 if (rc != 0) // STALL on errors
3369 fsg_set_halt(fsg, fsg->ep0);
3370 else // Complete the status stage
3374 case FSG_STATE_CONFIG_CHANGE:
3375 rc = do_set_config(fsg, new_config);
3376 if (fsg->ep0_req_tag != exception_req_tag)
3378 if (rc != 0) // STALL on errors
3379 fsg_set_halt(fsg, fsg->ep0);
3380 else // Complete the status stage
3384 case FSG_STATE_DISCONNECT:
3386 do_set_config(fsg, 0); // Unconfigured state
3389 case FSG_STATE_EXIT:
3390 case FSG_STATE_TERMINATED:
3391 do_set_config(fsg, 0); // Free resources
3392 spin_lock_irq(&fsg->lock);
3393 fsg->state = FSG_STATE_TERMINATED; // Stop the thread
3394 spin_unlock_irq(&fsg->lock);
3400 /*-------------------------------------------------------------------------*/
3402 static int fsg_main_thread(void *fsg_)
3404 struct fsg_dev *fsg = (struct fsg_dev *) fsg_;
3406 /* Allow the thread to be killed by a signal, but set the signal mask
3407 * to block everything but INT, TERM, KILL, and USR1. */
3408 siginitsetinv(&fsg->thread_signal_mask, sigmask(SIGINT) |
3409 sigmask(SIGTERM) | sigmask(SIGKILL) |
3411 sigprocmask(SIG_SETMASK, &fsg->thread_signal_mask, NULL);
3413 /* Arrange for userspace references to be interpreted as kernel
3414 * pointers. That way we can pass a kernel pointer to a routine
3415 * that expects a __user pointer and it will work okay. */
3419 while (fsg->state != FSG_STATE_TERMINATED) {
3420 if (exception_in_progress(fsg) || signal_pending(current)) {
3421 handle_exception(fsg);
3425 if (!fsg->running) {
3430 if (get_next_command(fsg))
3433 spin_lock_irq(&fsg->lock);
3434 if (!exception_in_progress(fsg))
3435 fsg->state = FSG_STATE_DATA_PHASE;
3436 spin_unlock_irq(&fsg->lock);
3438 if (do_scsi_command(fsg) || finish_reply(fsg))
3441 spin_lock_irq(&fsg->lock);
3442 if (!exception_in_progress(fsg))
3443 fsg->state = FSG_STATE_STATUS_PHASE;
3444 spin_unlock_irq(&fsg->lock);
3446 if (send_status(fsg))
3449 spin_lock_irq(&fsg->lock);
3450 if (!exception_in_progress(fsg))
3451 fsg->state = FSG_STATE_IDLE;
3452 spin_unlock_irq(&fsg->lock);
3455 spin_lock_irq(&fsg->lock);
3456 fsg->thread_task = NULL;
3457 spin_unlock_irq(&fsg->lock);
3459 /* In case we are exiting because of a signal, unregister the
3460 * gadget driver and close the backing file. */
3461 if (test_and_clear_bit(REGISTERED, &fsg->atomic_bitflags)) {
3462 usb_gadget_unregister_driver(&fsg_driver);
3463 close_all_backing_files(fsg);
3466 /* Let the unbind and cleanup routines know the thread has exited */
3467 complete_and_exit(&fsg->thread_notifier, 0);
3471 /*-------------------------------------------------------------------------*/
3473 /* If the next two routines are called while the gadget is registered,
3474 * the caller must own fsg->filesem for writing. */
3476 static int open_backing_file(struct lun *curlun, const char *filename)
3479 struct file *filp = NULL;
3481 struct inode *inode = NULL;
3485 /* R/W if we can, R/O if we must */
3488 filp = filp_open(filename, O_RDWR | O_LARGEFILE, 0);
3489 if (-EROFS == PTR_ERR(filp))
3493 filp = filp_open(filename, O_RDONLY | O_LARGEFILE, 0);
3495 LINFO(curlun, "unable to open backing file: %s\n", filename);
3496 return PTR_ERR(filp);
3499 if (!(filp->f_mode & FMODE_WRITE))
3503 inode = filp->f_dentry->d_inode;
3504 if (inode && S_ISBLK(inode->i_mode)) {
3505 if (bdev_read_only(inode->i_bdev))
3507 } else if (!inode || !S_ISREG(inode->i_mode)) {
3508 LINFO(curlun, "invalid file type: %s\n", filename);
3512 /* If we can't read the file, it's no good.
3513 * If we can't write the file, use it read-only. */
3514 if (!filp->f_op || !(filp->f_op->read || filp->f_op->aio_read)) {
3515 LINFO(curlun, "file not readable: %s\n", filename);
3518 if (!(filp->f_op->write || filp->f_op->aio_write))
3521 size = i_size_read(inode->i_mapping->host);
3523 LINFO(curlun, "unable to find file size: %s\n", filename);
3527 num_sectors = size >> 9; // File size in 512-byte sectors
3528 if (num_sectors == 0) {
3529 LINFO(curlun, "file too small: %s\n", filename);
3536 curlun->filp = filp;
3537 curlun->file_length = size;
3538 curlun->num_sectors = num_sectors;
3539 LDBG(curlun, "open backing file: %s\n", filename);
3543 filp_close(filp, current->files);
3548 static void close_backing_file(struct lun *curlun)
3551 LDBG(curlun, "close backing file\n");
3553 curlun->filp = NULL;
3557 static void close_all_backing_files(struct fsg_dev *fsg)
3561 for (i = 0; i < fsg->nluns; ++i)
3562 close_backing_file(&fsg->luns[i]);
3566 static ssize_t show_ro(struct device *dev, struct device_attribute *attr, char *buf)
3568 struct lun *curlun = dev_to_lun(dev);
3570 return sprintf(buf, "%d\n", curlun->ro);
3573 static ssize_t show_file(struct device *dev, struct device_attribute *attr, char *buf)
3575 struct lun *curlun = dev_to_lun(dev);
3576 struct fsg_dev *fsg = (struct fsg_dev *) dev_get_drvdata(dev);
3580 down_read(&fsg->filesem);
3581 if (backing_file_is_open(curlun)) { // Get the complete pathname
3582 p = d_path(curlun->filp->f_dentry, curlun->filp->f_vfsmnt,
3583 buf, PAGE_SIZE - 1);
3588 memmove(buf, p, rc);
3589 buf[rc] = '\n'; // Add a newline
3592 } else { // No file, return 0 bytes
3596 up_read(&fsg->filesem);
3601 static ssize_t store_ro(struct device *dev, struct device_attribute *attr, const char *buf, size_t count)
3604 struct lun *curlun = dev_to_lun(dev);
3605 struct fsg_dev *fsg = (struct fsg_dev *) dev_get_drvdata(dev);
3608 if (sscanf(buf, "%d", &i) != 1)
3611 /* Allow the write-enable status to change only while the backing file
3613 down_read(&fsg->filesem);
3614 if (backing_file_is_open(curlun)) {
3615 LDBG(curlun, "read-only status change prevented\n");
3619 LDBG(curlun, "read-only status set to %d\n", curlun->ro);
3621 up_read(&fsg->filesem);
3625 static ssize_t store_file(struct device *dev, struct device_attribute *attr, const char *buf, size_t count)
3627 struct lun *curlun = dev_to_lun(dev);
3628 struct fsg_dev *fsg = (struct fsg_dev *) dev_get_drvdata(dev);
3631 if (curlun->prevent_medium_removal && backing_file_is_open(curlun)) {
3632 LDBG(curlun, "eject attempt prevented\n");
3633 return -EBUSY; // "Door is locked"
3636 /* Remove a trailing newline */
3637 if (count > 0 && buf[count-1] == '\n')
3638 ((char *) buf)[count-1] = 0; // Ugh!
3640 /* Eject current medium */
3641 down_write(&fsg->filesem);
3642 if (backing_file_is_open(curlun)) {
3643 close_backing_file(curlun);
3644 curlun->unit_attention_data = SS_MEDIUM_NOT_PRESENT;
3647 /* Load new medium */
3648 if (count > 0 && buf[0]) {
3649 rc = open_backing_file(curlun, buf);
3651 curlun->unit_attention_data =
3652 SS_NOT_READY_TO_READY_TRANSITION;
3654 up_write(&fsg->filesem);
3655 return (rc < 0 ? rc : count);
3659 /* The write permissions and store_xxx pointers are set in fsg_bind() */
3660 static DEVICE_ATTR(ro, 0444, show_ro, NULL);
3661 static DEVICE_ATTR(file, 0444, show_file, NULL);
3664 /*-------------------------------------------------------------------------*/
3666 static void fsg_release(struct kref *ref)
3668 struct fsg_dev *fsg = container_of(ref, struct fsg_dev, ref);
3674 static void lun_release(struct device *dev)
3676 struct fsg_dev *fsg = (struct fsg_dev *) dev_get_drvdata(dev);
3678 kref_put(&fsg->ref, fsg_release);
3681 static void __exit fsg_unbind(struct usb_gadget *gadget)
3683 struct fsg_dev *fsg = get_gadget_data(gadget);
3686 struct usb_request *req = fsg->ep0req;
3688 DBG(fsg, "unbind\n");
3689 clear_bit(REGISTERED, &fsg->atomic_bitflags);
3691 /* Unregister the sysfs attribute files and the LUNs */
3692 for (i = 0; i < fsg->nluns; ++i) {
3693 curlun = &fsg->luns[i];
3694 if (curlun->registered) {
3695 device_remove_file(&curlun->dev, &dev_attr_ro);
3696 device_remove_file(&curlun->dev, &dev_attr_file);
3697 device_unregister(&curlun->dev);
3698 curlun->registered = 0;
3702 /* If the thread isn't already dead, tell it to exit now */
3703 if (fsg->state != FSG_STATE_TERMINATED) {
3704 raise_exception(fsg, FSG_STATE_EXIT);
3705 wait_for_completion(&fsg->thread_notifier);
3707 /* The cleanup routine waits for this completion also */
3708 complete(&fsg->thread_notifier);
3711 /* Free the data buffers */
3712 for (i = 0; i < NUM_BUFFERS; ++i) {
3713 struct fsg_buffhd *bh = &fsg->buffhds[i];
3716 usb_ep_free_buffer(fsg->bulk_in, bh->buf, bh->dma,
3720 /* Free the request and buffer for endpoint 0 */
3723 usb_ep_free_buffer(fsg->ep0, req->buf,
3724 req->dma, EP0_BUFSIZE);
3725 usb_ep_free_request(fsg->ep0, req);
3728 set_gadget_data(gadget, NULL);
3732 static int __init check_parameters(struct fsg_dev *fsg)
3737 /* Store the default values */
3738 mod_data.transport_type = USB_PR_BULK;
3739 mod_data.transport_name = "Bulk-only";
3740 mod_data.protocol_type = USB_SC_SCSI;
3741 mod_data.protocol_name = "Transparent SCSI";
3743 if (gadget_is_sh(fsg->gadget))
3744 mod_data.can_stall = 0;
3746 if (mod_data.release == 0xffff) { // Parameter wasn't set
3747 /* The sa1100 controller is not supported */
3748 if (gadget_is_sa1100(fsg->gadget))
3751 gcnum = usb_gadget_controller_number(fsg->gadget);
3753 mod_data.release = 0x0300 + gcnum;
3755 WARN(fsg, "controller '%s' not recognized\n",
3757 mod_data.release = 0x0399;
3761 prot = simple_strtol(mod_data.protocol_parm, NULL, 0);
3763 #ifdef CONFIG_USB_FILE_STORAGE_TEST
3764 if (strnicmp(mod_data.transport_parm, "BBB", 10) == 0) {
3765 ; // Use default setting
3766 } else if (strnicmp(mod_data.transport_parm, "CB", 10) == 0) {
3767 mod_data.transport_type = USB_PR_CB;
3768 mod_data.transport_name = "Control-Bulk";
3769 } else if (strnicmp(mod_data.transport_parm, "CBI", 10) == 0) {
3770 mod_data.transport_type = USB_PR_CBI;
3771 mod_data.transport_name = "Control-Bulk-Interrupt";
3773 ERROR(fsg, "invalid transport: %s\n", mod_data.transport_parm);
3777 if (strnicmp(mod_data.protocol_parm, "SCSI", 10) == 0 ||
3778 prot == USB_SC_SCSI) {
3779 ; // Use default setting
3780 } else if (strnicmp(mod_data.protocol_parm, "RBC", 10) == 0 ||
3781 prot == USB_SC_RBC) {
3782 mod_data.protocol_type = USB_SC_RBC;
3783 mod_data.protocol_name = "RBC";
3784 } else if (strnicmp(mod_data.protocol_parm, "8020", 4) == 0 ||
3785 strnicmp(mod_data.protocol_parm, "ATAPI", 10) == 0 ||
3786 prot == USB_SC_8020) {
3787 mod_data.protocol_type = USB_SC_8020;
3788 mod_data.protocol_name = "8020i (ATAPI)";
3789 } else if (strnicmp(mod_data.protocol_parm, "QIC", 3) == 0 ||
3790 prot == USB_SC_QIC) {
3791 mod_data.protocol_type = USB_SC_QIC;
3792 mod_data.protocol_name = "QIC-157";
3793 } else if (strnicmp(mod_data.protocol_parm, "UFI", 10) == 0 ||
3794 prot == USB_SC_UFI) {
3795 mod_data.protocol_type = USB_SC_UFI;
3796 mod_data.protocol_name = "UFI";
3797 } else if (strnicmp(mod_data.protocol_parm, "8070", 4) == 0 ||
3798 prot == USB_SC_8070) {
3799 mod_data.protocol_type = USB_SC_8070;
3800 mod_data.protocol_name = "8070i";
3802 ERROR(fsg, "invalid protocol: %s\n", mod_data.protocol_parm);
3806 mod_data.buflen &= PAGE_CACHE_MASK;
3807 if (mod_data.buflen <= 0) {
3808 ERROR(fsg, "invalid buflen\n");
3811 #endif /* CONFIG_USB_FILE_STORAGE_TEST */
3817 static int __init fsg_bind(struct usb_gadget *gadget)
3819 struct fsg_dev *fsg = the_fsg;
3824 struct usb_request *req;
3827 fsg->gadget = gadget;
3828 set_gadget_data(gadget, fsg);
3829 fsg->ep0 = gadget->ep0;
3830 fsg->ep0->driver_data = fsg;
3832 if ((rc = check_parameters(fsg)) != 0)
3835 if (mod_data.removable) { // Enable the store_xxx attributes
3836 dev_attr_ro.attr.mode = dev_attr_file.attr.mode = 0644;
3837 dev_attr_ro.store = store_ro;
3838 dev_attr_file.store = store_file;
3841 /* Find out how many LUNs there should be */
3844 i = max(mod_data.num_filenames, 1);
3846 ERROR(fsg, "invalid number of LUNs: %d\n", i);
3851 /* Create the LUNs, open their backing files, and register the
3852 * LUN devices in sysfs. */
3853 fsg->luns = kzalloc(i * sizeof(struct lun), GFP_KERNEL);
3860 for (i = 0; i < fsg->nluns; ++i) {
3861 curlun = &fsg->luns[i];
3863 curlun->dev.parent = &gadget->dev;
3864 curlun->dev.driver = &fsg_driver.driver;
3865 dev_set_drvdata(&curlun->dev, fsg);
3866 snprintf(curlun->dev.bus_id, BUS_ID_SIZE,
3867 "%s-lun%d", gadget->dev.bus_id, i);
3869 if ((rc = device_register(&curlun->dev)) != 0)
3870 INFO(fsg, "failed to register LUN%d: %d\n", i, rc);
3872 curlun->registered = 1;
3873 curlun->dev.release = lun_release;
3874 device_create_file(&curlun->dev, &dev_attr_ro);
3875 device_create_file(&curlun->dev, &dev_attr_file);
3876 kref_get(&fsg->ref);
3879 if (file[i] && *file[i]) {
3880 if ((rc = open_backing_file(curlun, file[i])) != 0)
3882 } else if (!mod_data.removable) {
3883 ERROR(fsg, "no file given for LUN%d\n", i);
3889 /* Find all the endpoints we will use */
3890 usb_ep_autoconfig_reset(gadget);
3891 ep = usb_ep_autoconfig(gadget, &fs_bulk_in_desc);
3894 ep->driver_data = fsg; // claim the endpoint
3897 ep = usb_ep_autoconfig(gadget, &fs_bulk_out_desc);
3900 ep->driver_data = fsg; // claim the endpoint
3903 if (transport_is_cbi()) {
3904 ep = usb_ep_autoconfig(gadget, &fs_intr_in_desc);
3907 ep->driver_data = fsg; // claim the endpoint
3911 /* Fix up the descriptors */
3912 device_desc.bMaxPacketSize0 = fsg->ep0->maxpacket;
3913 device_desc.idVendor = cpu_to_le16(mod_data.vendor);
3914 device_desc.idProduct = cpu_to_le16(mod_data.product);
3915 device_desc.bcdDevice = cpu_to_le16(mod_data.release);
3917 i = (transport_is_cbi() ? 3 : 2); // Number of endpoints
3918 intf_desc.bNumEndpoints = i;
3919 intf_desc.bInterfaceSubClass = mod_data.protocol_type;
3920 intf_desc.bInterfaceProtocol = mod_data.transport_type;
3921 fs_function[i + FS_FUNCTION_PRE_EP_ENTRIES] = NULL;
3923 #ifdef CONFIG_USB_GADGET_DUALSPEED
3924 hs_function[i + HS_FUNCTION_PRE_EP_ENTRIES] = NULL;
3926 /* Assume ep0 uses the same maxpacket value for both speeds */
3927 dev_qualifier.bMaxPacketSize0 = fsg->ep0->maxpacket;
3929 /* Assume that all endpoint addresses are the same for both speeds */
3930 hs_bulk_in_desc.bEndpointAddress = fs_bulk_in_desc.bEndpointAddress;
3931 hs_bulk_out_desc.bEndpointAddress = fs_bulk_out_desc.bEndpointAddress;
3932 hs_intr_in_desc.bEndpointAddress = fs_intr_in_desc.bEndpointAddress;
3935 if (gadget->is_otg) {
3936 otg_desc.bmAttributes |= USB_OTG_HNP,
3937 config_desc.bmAttributes |= USB_CONFIG_ATT_WAKEUP;
3942 /* Allocate the request and buffer for endpoint 0 */
3943 fsg->ep0req = req = usb_ep_alloc_request(fsg->ep0, GFP_KERNEL);
3946 req->buf = usb_ep_alloc_buffer(fsg->ep0, EP0_BUFSIZE,
3947 &req->dma, GFP_KERNEL);
3950 req->complete = ep0_complete;
3952 /* Allocate the data buffers */
3953 for (i = 0; i < NUM_BUFFERS; ++i) {
3954 struct fsg_buffhd *bh = &fsg->buffhds[i];
3956 bh->buf = usb_ep_alloc_buffer(fsg->bulk_in, mod_data.buflen,
3957 &bh->dma, GFP_KERNEL);
3962 fsg->buffhds[NUM_BUFFERS - 1].next = &fsg->buffhds[0];
3964 /* This should reflect the actual gadget power source */
3965 usb_gadget_set_selfpowered(gadget);
3967 snprintf(manufacturer, sizeof manufacturer, "%s %s with %s",
3968 system_utsname.sysname, system_utsname.release,
3971 /* On a real device, serial[] would be loaded from permanent
3972 * storage. We just encode it from the driver version string. */
3973 for (i = 0; i < sizeof(serial) - 2; i += 2) {
3974 unsigned char c = DRIVER_VERSION[i / 2];
3978 sprintf(&serial[i], "%02X", c);
3981 fsg->thread_task = kthread_create(fsg_main_thread, fsg,
3982 "file-storage-gadget");
3983 if (IS_ERR(fsg->thread_task)) {
3984 rc = PTR_ERR(fsg->thread_task);
3988 INFO(fsg, DRIVER_DESC ", version: " DRIVER_VERSION "\n");
3989 INFO(fsg, "Number of LUNs=%d\n", fsg->nluns);
3991 pathbuf = kmalloc(PATH_MAX, GFP_KERNEL);
3992 for (i = 0; i < fsg->nluns; ++i) {
3993 curlun = &fsg->luns[i];
3994 if (backing_file_is_open(curlun)) {
3997 p = d_path(curlun->filp->f_dentry,
3998 curlun->filp->f_vfsmnt,
4003 LINFO(curlun, "ro=%d, file: %s\n",
4004 curlun->ro, (p ? p : "(error)"));
4009 DBG(fsg, "transport=%s (x%02x)\n",
4010 mod_data.transport_name, mod_data.transport_type);
4011 DBG(fsg, "protocol=%s (x%02x)\n",
4012 mod_data.protocol_name, mod_data.protocol_type);
4013 DBG(fsg, "VendorID=x%04x, ProductID=x%04x, Release=x%04x\n",
4014 mod_data.vendor, mod_data.product, mod_data.release);
4015 DBG(fsg, "removable=%d, stall=%d, buflen=%u\n",
4016 mod_data.removable, mod_data.can_stall,
4018 DBG(fsg, "I/O thread pid: %d\n", fsg->thread_task->pid);
4020 set_bit(REGISTERED, &fsg->atomic_bitflags);
4022 /* Tell the thread to start working */
4023 wake_up_process(fsg->thread_task);
4027 ERROR(fsg, "unable to autoconfigure all endpoints\n");
4031 fsg->state = FSG_STATE_TERMINATED; // The thread is dead
4033 close_all_backing_files(fsg);
4038 /*-------------------------------------------------------------------------*/
4040 static void fsg_suspend(struct usb_gadget *gadget)
4042 struct fsg_dev *fsg = get_gadget_data(gadget);
4044 DBG(fsg, "suspend\n");
4045 set_bit(SUSPENDED, &fsg->atomic_bitflags);
4048 static void fsg_resume(struct usb_gadget *gadget)
4050 struct fsg_dev *fsg = get_gadget_data(gadget);
4052 DBG(fsg, "resume\n");
4053 clear_bit(SUSPENDED, &fsg->atomic_bitflags);
4057 /*-------------------------------------------------------------------------*/
4059 static struct usb_gadget_driver fsg_driver = {
4060 #ifdef CONFIG_USB_GADGET_DUALSPEED
4061 .speed = USB_SPEED_HIGH,
4063 .speed = USB_SPEED_FULL,
4065 .function = (char *) longname,
4067 .unbind = __exit_p(fsg_unbind),
4068 .disconnect = fsg_disconnect,
4070 .suspend = fsg_suspend,
4071 .resume = fsg_resume,
4074 .name = (char *) shortname,
4075 .owner = THIS_MODULE,
4083 static int __init fsg_alloc(void)
4085 struct fsg_dev *fsg;
4087 fsg = kzalloc(sizeof *fsg, GFP_KERNEL);
4090 spin_lock_init(&fsg->lock);
4091 init_rwsem(&fsg->filesem);
4092 kref_init(&fsg->ref);
4093 init_completion(&fsg->thread_notifier);
4100 static int __init fsg_init(void)
4103 struct fsg_dev *fsg;
4105 if ((rc = fsg_alloc()) != 0)
4108 if ((rc = usb_gadget_register_driver(&fsg_driver)) != 0)
4109 kref_put(&fsg->ref, fsg_release);
4112 module_init(fsg_init);
4115 static void __exit fsg_cleanup(void)
4117 struct fsg_dev *fsg = the_fsg;
4119 /* Unregister the driver iff the thread hasn't already done so */
4120 if (test_and_clear_bit(REGISTERED, &fsg->atomic_bitflags))
4121 usb_gadget_unregister_driver(&fsg_driver);
4123 /* Wait for the thread to finish up */
4124 wait_for_completion(&fsg->thread_notifier);
4126 close_all_backing_files(fsg);
4127 kref_put(&fsg->ref, fsg_release);
4129 module_exit(fsg_cleanup);
projects / linux-2.6 / blob