2 * ti113x.h 1.16 1999/10/25 20:03:34
4 * The contents of this file are subject to the Mozilla Public License
5 * Version 1.1 (the "License"); you may not use this file except in
6 * compliance with the License. You may obtain a copy of the License
7 * at http://www.mozilla.org/MPL/
9 * Software distributed under the License is distributed on an "AS IS"
10 * basis, WITHOUT WARRANTY OF ANY KIND, either express or implied. See
11 * the License for the specific language governing rights and
12 * limitations under the License.
14 * The initial developer of the original code is David A. Hinds
15 * <dahinds@users.sourceforge.net>. Portions created by David A. Hinds
16 * are Copyright (C) 1999 David A. Hinds. All Rights Reserved.
18 * Alternatively, the contents of this file may be used under the
19 * terms of the GNU General Public License version 2 (the "GPL"), in which
20 * case the provisions of the GPL are applicable instead of the
21 * above. If you wish to allow the use of your version of this file
22 * only under the terms of the GPL and not to allow others to use
23 * your version of this file under the MPL, indicate your decision by
24 * deleting the provisions above and replace them with the notice and
25 * other provisions required by the GPL. If you do not delete the
26 * provisions above, a recipient may use your version of this file
27 * under either the MPL or the GPL.
30 #ifndef _LINUX_TI113X_H
31 #define _LINUX_TI113X_H
34 /* Register definitions for TI 113X PCI-to-CardBus bridges */
36 /* System Control Register */
37 #define TI113X_SYSTEM_CONTROL 0x0080 /* 32 bit */
38 #define TI113X_SCR_SMIROUTE 0x04000000
39 #define TI113X_SCR_SMISTATUS 0x02000000
40 #define TI113X_SCR_SMIENB 0x01000000
41 #define TI113X_SCR_VCCPROT 0x00200000
42 #define TI113X_SCR_REDUCEZV 0x00100000
43 #define TI113X_SCR_CDREQEN 0x00080000
44 #define TI113X_SCR_CDMACHAN 0x00070000
45 #define TI113X_SCR_SOCACTIVE 0x00002000
46 #define TI113X_SCR_PWRSTREAM 0x00000800
47 #define TI113X_SCR_DELAYUP 0x00000400
48 #define TI113X_SCR_DELAYDOWN 0x00000200
49 #define TI113X_SCR_INTERROGATE 0x00000100
50 #define TI113X_SCR_CLKRUN_SEL 0x00000080
51 #define TI113X_SCR_PWRSAVINGS 0x00000040
52 #define TI113X_SCR_SUBSYSRW 0x00000020
53 #define TI113X_SCR_CB_DPAR 0x00000010
54 #define TI113X_SCR_CDMA_EN 0x00000008
55 #define TI113X_SCR_ASYNC_IRQ 0x00000004
56 #define TI113X_SCR_KEEPCLK 0x00000002
57 #define TI113X_SCR_CLKRUN_ENA 0x00000001
59 #define TI122X_SCR_SER_STEP 0xc0000000
60 #define TI122X_SCR_INTRTIE 0x20000000
61 #define TIXX21_SCR_TIEALL 0x10000000
62 #define TI122X_SCR_CBRSVD 0x00400000
63 #define TI122X_SCR_MRBURSTDN 0x00008000
64 #define TI122X_SCR_MRBURSTUP 0x00004000
65 #define TI122X_SCR_RIMUX 0x00000001
67 /* Multimedia Control Register */
68 #define TI1250_MULTIMEDIA_CTL 0x0084 /* 8 bit */
69 #define TI1250_MMC_ZVOUTEN 0x80
70 #define TI1250_MMC_PORTSEL 0x40
71 #define TI1250_MMC_ZVEN1 0x02
72 #define TI1250_MMC_ZVEN0 0x01
74 #define TI1250_GENERAL_STATUS 0x0085 /* 8 bit */
75 #define TI1250_GPIO0_CONTROL 0x0088 /* 8 bit */
76 #define TI1250_GPIO1_CONTROL 0x0089 /* 8 bit */
77 #define TI1250_GPIO2_CONTROL 0x008a /* 8 bit */
78 #define TI1250_GPIO3_CONTROL 0x008b /* 8 bit */
79 #define TI1250_GPIO_MODE_MASK 0xc0
81 /* IRQMUX/MFUNC Register */
82 #define TI122X_MFUNC 0x008c /* 32 bit */
83 #define TI122X_MFUNC0_MASK 0x0000000f
84 #define TI122X_MFUNC1_MASK 0x000000f0
85 #define TI122X_MFUNC2_MASK 0x00000f00
86 #define TI122X_MFUNC3_MASK 0x0000f000
87 #define TI122X_MFUNC4_MASK 0x000f0000
88 #define TI122X_MFUNC5_MASK 0x00f00000
89 #define TI122X_MFUNC6_MASK 0x0f000000
91 #define TI122X_MFUNC0_INTA 0x00000002
92 #define TI125X_MFUNC0_INTB 0x00000001
93 #define TI122X_MFUNC1_INTB 0x00000020
94 #define TI122X_MFUNC3_IRQSER 0x00001000
97 /* Retry Status Register */
98 #define TI113X_RETRY_STATUS 0x0090 /* 8 bit */
99 #define TI113X_RSR_PCIRETRY 0x80
100 #define TI113X_RSR_CBRETRY 0x40
101 #define TI113X_RSR_TEXP_CBB 0x20
102 #define TI113X_RSR_MEXP_CBB 0x10
103 #define TI113X_RSR_TEXP_CBA 0x08
104 #define TI113X_RSR_MEXP_CBA 0x04
105 #define TI113X_RSR_TEXP_PCI 0x02
106 #define TI113X_RSR_MEXP_PCI 0x01
108 /* Card Control Register */
109 #define TI113X_CARD_CONTROL 0x0091 /* 8 bit */
110 #define TI113X_CCR_RIENB 0x80
111 #define TI113X_CCR_ZVENABLE 0x40
112 #define TI113X_CCR_PCI_IRQ_ENA 0x20
113 #define TI113X_CCR_PCI_IREQ 0x10
114 #define TI113X_CCR_PCI_CSC 0x08
115 #define TI113X_CCR_SPKROUTEN 0x02
116 #define TI113X_CCR_IFG 0x01
118 #define TI1220_CCR_PORT_SEL 0x20
119 #define TI122X_CCR_AUD2MUX 0x04
121 /* Device Control Register */
122 #define TI113X_DEVICE_CONTROL 0x0092 /* 8 bit */
123 #define TI113X_DCR_5V_FORCE 0x40
124 #define TI113X_DCR_3V_FORCE 0x20
125 #define TI113X_DCR_IMODE_MASK 0x06
126 #define TI113X_DCR_IMODE_ISA 0x02
127 #define TI113X_DCR_IMODE_SERIAL 0x04
129 #define TI12XX_DCR_IMODE_PCI_ONLY 0x00
130 #define TI12XX_DCR_IMODE_ALL_SERIAL 0x06
132 /* Buffer Control Register */
133 #define TI113X_BUFFER_CONTROL 0x0093 /* 8 bit */
134 #define TI113X_BCR_CB_READ_DEPTH 0x08
135 #define TI113X_BCR_CB_WRITE_DEPTH 0x04
136 #define TI113X_BCR_PCI_READ_DEPTH 0x02
137 #define TI113X_BCR_PCI_WRITE_DEPTH 0x01
139 /* Diagnostic Register */
140 #define TI1250_DIAGNOSTIC 0x0093 /* 8 bit */
141 #define TI1250_DIAG_TRUE_VALUE 0x80
142 #define TI1250_DIAG_PCI_IREQ 0x40
143 #define TI1250_DIAG_PCI_CSC 0x20
144 #define TI1250_DIAG_ASYNC_CSC 0x01
147 #define TI113X_DMA_0 0x0094 /* 32 bit */
148 #define TI113X_DMA_1 0x0098 /* 32 bit */
150 /* ExCA IO offset registers */
151 #define TI113X_IO_OFFSET(map) (0x36+((map)<<1))
153 /* EnE test register */
154 #define ENE_TEST_C9 0xc9 /* 8bit */
155 #define ENE_TEST_C9_TLTENABLE 0x02
156 #define ENE_TEST_C9_PFENABLE_F0 0x04
157 #define ENE_TEST_C9_PFENABLE_F1 0x08
158 #define ENE_TEST_C9_PFENABLE (ENE_TEST_C9_PFENABLE_F0 | ENE_TEST_C9_PFENABLE_F1)
159 #define ENE_TEST_C9_WPDISALBLE_F0 0x40
160 #define ENE_TEST_C9_WPDISALBLE_F1 0x80
161 #define ENE_TEST_C9_WPDISALBLE (ENE_TEST_C9_WPDISALBLE_F0 | ENE_TEST_C9_WPDISALBLE_F1)
164 * Texas Instruments CardBus controller overrides.
166 #define ti_sysctl(socket) ((socket)->private[0])
167 #define ti_cardctl(socket) ((socket)->private[1])
168 #define ti_devctl(socket) ((socket)->private[2])
169 #define ti_diag(socket) ((socket)->private[3])
170 #define ti_mfunc(socket) ((socket)->private[4])
171 #define ene_test_c9(socket) ((socket)->private[5])
174 * These are the TI specific power management handlers.
176 static void ti_save_state(struct yenta_socket *socket)
178 ti_sysctl(socket) = config_readl(socket, TI113X_SYSTEM_CONTROL);
179 ti_mfunc(socket) = config_readl(socket, TI122X_MFUNC);
180 ti_cardctl(socket) = config_readb(socket, TI113X_CARD_CONTROL);
181 ti_devctl(socket) = config_readb(socket, TI113X_DEVICE_CONTROL);
182 ti_diag(socket) = config_readb(socket, TI1250_DIAGNOSTIC);
184 if (socket->dev->vendor == PCI_VENDOR_ID_ENE)
185 ene_test_c9(socket) = config_readb(socket, ENE_TEST_C9);
188 static void ti_restore_state(struct yenta_socket *socket)
190 config_writel(socket, TI113X_SYSTEM_CONTROL, ti_sysctl(socket));
191 config_writel(socket, TI122X_MFUNC, ti_mfunc(socket));
192 config_writeb(socket, TI113X_CARD_CONTROL, ti_cardctl(socket));
193 config_writeb(socket, TI113X_DEVICE_CONTROL, ti_devctl(socket));
194 config_writeb(socket, TI1250_DIAGNOSTIC, ti_diag(socket));
196 if (socket->dev->vendor == PCI_VENDOR_ID_ENE)
197 config_writeb(socket, ENE_TEST_C9, ene_test_c9(socket));
201 * Zoom video control for TI122x/113x chips
204 static void ti_zoom_video(struct pcmcia_socket *sock, int onoff)
207 struct yenta_socket *socket = container_of(sock, struct yenta_socket, socket);
209 /* If we don't have a Zoom Video switch this is harmless,
210 we just tristate the unused (ZV) lines */
211 reg = config_readb(socket, TI113X_CARD_CONTROL);
213 /* Zoom zoom, we will all go together, zoom zoom, zoom zoom */
214 reg |= TI113X_CCR_ZVENABLE;
216 reg &= ~TI113X_CCR_ZVENABLE;
217 config_writeb(socket, TI113X_CARD_CONTROL, reg);
221 * The 145x series can also use this. They have an additional
222 * ZV autodetect mode we don't use but don't actually need.
223 * FIXME: manual says its in func0 and func1 but disagrees with
224 * itself about this - do we need to force func0, if so we need
225 * to know a lot more about socket pairings in pcmcia_socket than
229 static void ti1250_zoom_video(struct pcmcia_socket *sock, int onoff)
231 struct yenta_socket *socket = container_of(sock, struct yenta_socket, socket);
235 ti_zoom_video(sock, onoff);
237 reg = config_readb(socket, TI1250_MULTIMEDIA_CTL);
238 reg |= TI1250_MMC_ZVOUTEN; /* ZV bus enable */
240 if(PCI_FUNC(socket->dev->devfn)==1)
245 reg &= ~(1<<6); /* Clear select bit */
246 reg |= shift<<6; /* Favour our socket */
247 reg |= 1<<shift; /* Socket zoom video on */
251 reg &= ~(1<<6); /* Clear select bit */
252 reg |= (1^shift)<<6; /* Favour other socket */
253 reg &= ~(1<<shift); /* Socket zoon video off */
256 config_writeb(socket, TI1250_MULTIMEDIA_CTL, reg);
259 static void ti_set_zv(struct yenta_socket *socket)
261 if(socket->dev->vendor == PCI_VENDOR_ID_TI)
263 switch(socket->dev->device)
265 /* There may be more .. */
266 case PCI_DEVICE_ID_TI_1220:
267 case PCI_DEVICE_ID_TI_1221:
268 case PCI_DEVICE_ID_TI_1225:
269 case PCI_DEVICE_ID_TI_4510:
270 socket->socket.zoom_video = ti_zoom_video;
272 case PCI_DEVICE_ID_TI_1250:
273 case PCI_DEVICE_ID_TI_1251A:
274 case PCI_DEVICE_ID_TI_1251B:
275 case PCI_DEVICE_ID_TI_1450:
276 socket->socket.zoom_video = ti1250_zoom_video;
283 * Generic TI init - TI has an extension for the
284 * INTCTL register that sets the PCI CSC interrupt.
285 * Make sure we set it correctly at open and init
287 * - override: disable the PCI CSC interrupt. This makes
288 * it possible to use the CSC interrupt to probe the
290 * - init: set the interrupt to match our PCI state.
291 * This makes us correctly get PCI CSC interrupt
294 static int ti_init(struct yenta_socket *socket)
296 u8 new, reg = exca_readb(socket, I365_INTCTL);
298 new = reg & ~I365_INTR_ENA;
300 new |= I365_INTR_ENA;
302 exca_writeb(socket, I365_INTCTL, new);
306 static int ti_override(struct yenta_socket *socket)
308 u8 new, reg = exca_readb(socket, I365_INTCTL);
310 new = reg & ~I365_INTR_ENA;
312 exca_writeb(socket, I365_INTCTL, new);
319 static int ti113x_override(struct yenta_socket *socket)
323 cardctl = config_readb(socket, TI113X_CARD_CONTROL);
324 cardctl &= ~(TI113X_CCR_PCI_IRQ_ENA | TI113X_CCR_PCI_IREQ | TI113X_CCR_PCI_CSC);
326 cardctl |= TI113X_CCR_PCI_IRQ_ENA | TI113X_CCR_PCI_CSC | TI113X_CCR_PCI_IREQ;
327 config_writeb(socket, TI113X_CARD_CONTROL, cardctl);
329 return ti_override(socket);
333 /* irqrouting for func0, probes PCI interrupt and ISA interrupts */
334 static void ti12xx_irqroute_func0(struct yenta_socket *socket)
336 u32 mfunc, mfunc_old, devctl;
340 mfunc = mfunc_old = config_readl(socket, TI122X_MFUNC);
341 devctl = config_readb(socket, TI113X_DEVICE_CONTROL);
342 dev_printk(KERN_INFO, &socket->dev->dev,
343 "TI: mfunc 0x%08x, devctl 0x%02x\n", mfunc, devctl);
345 /* make sure PCI interrupts are enabled before probing */
348 /* test PCI interrupts first. only try fixing if return value is 0! */
349 pci_irq_status = yenta_probe_cb_irq(socket);
354 * We're here which means PCI interrupts are _not_ delivered. try to
355 * find the right setting (all serial or parallel)
357 dev_printk(KERN_INFO, &socket->dev->dev,
358 "TI: probing PCI interrupt failed, trying to fix\n");
360 /* for serial PCI make sure MFUNC3 is set to IRQSER */
361 if ((devctl & TI113X_DCR_IMODE_MASK) == TI12XX_DCR_IMODE_ALL_SERIAL) {
362 switch (socket->dev->device) {
363 case PCI_DEVICE_ID_TI_1250:
364 case PCI_DEVICE_ID_TI_1251A:
365 case PCI_DEVICE_ID_TI_1251B:
366 case PCI_DEVICE_ID_TI_1450:
367 case PCI_DEVICE_ID_TI_1451A:
368 case PCI_DEVICE_ID_TI_4450:
369 case PCI_DEVICE_ID_TI_4451:
370 /* these chips have no IRQSER setting in MFUNC3 */
374 mfunc = (mfunc & ~TI122X_MFUNC3_MASK) | TI122X_MFUNC3_IRQSER;
376 /* write down if changed, probe */
377 if (mfunc != mfunc_old) {
378 config_writel(socket, TI122X_MFUNC, mfunc);
380 pci_irq_status = yenta_probe_cb_irq(socket);
381 if (pci_irq_status == 1) {
382 dev_printk(KERN_INFO, &socket->dev->dev,
383 "TI: all-serial interrupts ok\n");
388 /* not working, back to old value */
390 config_writel(socket, TI122X_MFUNC, mfunc);
392 if (pci_irq_status == -1)
397 /* serial PCI interrupts not working fall back to parallel */
398 dev_printk(KERN_INFO, &socket->dev->dev,
399 "TI: falling back to parallel PCI interrupts\n");
400 devctl &= ~TI113X_DCR_IMODE_MASK;
401 devctl |= TI113X_DCR_IMODE_SERIAL; /* serial ISA could be right */
402 config_writeb(socket, TI113X_DEVICE_CONTROL, devctl);
405 /* parallel PCI interrupts: route INTA */
406 switch (socket->dev->device) {
407 case PCI_DEVICE_ID_TI_1250:
408 case PCI_DEVICE_ID_TI_1251A:
409 case PCI_DEVICE_ID_TI_1251B:
410 case PCI_DEVICE_ID_TI_1450:
411 /* make sure GPIO3 is set to INTA */
412 gpio3 = gpio3_old = config_readb(socket, TI1250_GPIO3_CONTROL);
413 gpio3 &= ~TI1250_GPIO_MODE_MASK;
414 if (gpio3 != gpio3_old)
415 config_writeb(socket, TI1250_GPIO3_CONTROL, gpio3);
419 gpio3 = gpio3_old = 0;
421 mfunc = (mfunc & ~TI122X_MFUNC0_MASK) | TI122X_MFUNC0_INTA;
422 if (mfunc != mfunc_old)
423 config_writel(socket, TI122X_MFUNC, mfunc);
426 /* time to probe again */
427 pci_irq_status = yenta_probe_cb_irq(socket);
428 if (pci_irq_status == 1) {
430 dev_printk(KERN_INFO, &socket->dev->dev,
431 "TI: parallel PCI interrupts ok\n");
433 /* not working, back to old value */
435 config_writel(socket, TI122X_MFUNC, mfunc);
436 if (gpio3 != gpio3_old)
437 config_writeb(socket, TI1250_GPIO3_CONTROL, gpio3_old);
441 if (pci_irq_status < 1) {
443 dev_printk(KERN_INFO, &socket->dev->dev,
444 "Yenta TI: no PCI interrupts. Fish. "
450 /* changes the irq of func1 to match that of func0 */
451 static int ti12xx_align_irqs(struct yenta_socket *socket, int *old_irq)
453 struct pci_dev *func0;
455 /* find func0 device */
456 func0 = pci_get_slot(socket->dev->bus, socket->dev->devfn & ~0x07);
461 *old_irq = socket->cb_irq;
462 socket->cb_irq = socket->dev->irq = func0->irq;
470 * ties INTA and INTB together. also changes the devices irq to that of
471 * the function 0 device. call from func1 only.
472 * returns 1 if INTRTIE changed, 0 otherwise.
474 static int ti12xx_tie_interrupts(struct yenta_socket *socket, int *old_irq)
479 sysctl = config_readl(socket, TI113X_SYSTEM_CONTROL);
480 if (sysctl & TI122X_SCR_INTRTIE)
484 ret = ti12xx_align_irqs(socket, old_irq);
489 sysctl |= TI122X_SCR_INTRTIE;
490 config_writel(socket, TI113X_SYSTEM_CONTROL, sysctl);
495 /* undo what ti12xx_tie_interrupts() did */
496 static void ti12xx_untie_interrupts(struct yenta_socket *socket, int old_irq)
498 u32 sysctl = config_readl(socket, TI113X_SYSTEM_CONTROL);
499 sysctl &= ~TI122X_SCR_INTRTIE;
500 config_writel(socket, TI113X_SYSTEM_CONTROL, sysctl);
502 socket->cb_irq = socket->dev->irq = old_irq;
506 * irqrouting for func1, plays with INTB routing
507 * only touches MFUNC for INTB routing. all other bits are taken
508 * care of in func0 already.
510 static void ti12xx_irqroute_func1(struct yenta_socket *socket)
512 u32 mfunc, mfunc_old, devctl, sysctl;
515 mfunc = mfunc_old = config_readl(socket, TI122X_MFUNC);
516 devctl = config_readb(socket, TI113X_DEVICE_CONTROL);
517 dev_printk(KERN_INFO, &socket->dev->dev,
518 "TI: mfunc 0x%08x, devctl 0x%02x\n",
521 /* if IRQs are configured as tied, align irq of func1 with func0 */
522 sysctl = config_readl(socket, TI113X_SYSTEM_CONTROL);
523 if (sysctl & TI122X_SCR_INTRTIE)
524 ti12xx_align_irqs(socket, NULL);
526 /* make sure PCI interrupts are enabled before probing */
529 /* test PCI interrupts first. only try fixing if return value is 0! */
530 pci_irq_status = yenta_probe_cb_irq(socket);
535 * We're here which means PCI interrupts are _not_ delivered. try to
536 * find the right setting
538 dev_printk(KERN_INFO, &socket->dev->dev,
539 "TI: probing PCI interrupt failed, trying to fix\n");
541 /* if all serial: set INTRTIE, probe again */
542 if ((devctl & TI113X_DCR_IMODE_MASK) == TI12XX_DCR_IMODE_ALL_SERIAL) {
545 if (ti12xx_tie_interrupts(socket, &old_irq)) {
546 pci_irq_status = yenta_probe_cb_irq(socket);
547 if (pci_irq_status == 1) {
548 dev_printk(KERN_INFO, &socket->dev->dev,
549 "TI: all-serial interrupts, tied ok\n");
553 ti12xx_untie_interrupts(socket, old_irq);
556 /* parallel PCI: route INTB, probe again */
560 switch (socket->dev->device) {
561 case PCI_DEVICE_ID_TI_1250:
562 /* the 1250 has one pin for IRQSER/INTB depending on devctl */
565 case PCI_DEVICE_ID_TI_1251A:
566 case PCI_DEVICE_ID_TI_1251B:
567 case PCI_DEVICE_ID_TI_1450:
569 * those have a pin for IRQSER/INTB plus INTB in MFUNC0
570 * we alread probed the shared pin, now go for MFUNC0
572 mfunc = (mfunc & ~TI122X_MFUNC0_MASK) | TI125X_MFUNC0_INTB;
576 mfunc = (mfunc & ~TI122X_MFUNC1_MASK) | TI122X_MFUNC1_INTB;
581 if (mfunc != mfunc_old) {
582 config_writel(socket, TI122X_MFUNC, mfunc);
584 pci_irq_status = yenta_probe_cb_irq(socket);
585 if (pci_irq_status == 1) {
586 dev_printk(KERN_INFO, &socket->dev->dev,
587 "TI: parallel PCI interrupts ok\n");
592 config_writel(socket, TI122X_MFUNC, mfunc);
594 if (pci_irq_status == -1)
598 /* still nothing: set INTRTIE */
599 if (ti12xx_tie_interrupts(socket, &old_irq)) {
600 pci_irq_status = yenta_probe_cb_irq(socket);
601 if (pci_irq_status == 1) {
602 dev_printk(KERN_INFO, &socket->dev->dev,
603 "TI: parallel PCI interrupts, tied ok\n");
607 ti12xx_untie_interrupts(socket, old_irq);
612 if (pci_irq_status < 1) {
614 dev_printk(KERN_INFO, &socket->dev->dev,
615 "TI: no PCI interrupts. Fish. Please report.\n");
620 /* Returns true value if the second slot of a two-slot controller is empty */
621 static int ti12xx_2nd_slot_empty(struct yenta_socket *socket)
623 struct pci_dev *func;
624 struct yenta_socket *slot2;
630 /* catch the two-slot controllers */
631 switch (socket->dev->device) {
632 case PCI_DEVICE_ID_TI_1220:
633 case PCI_DEVICE_ID_TI_1221:
634 case PCI_DEVICE_ID_TI_1225:
635 case PCI_DEVICE_ID_TI_1251A:
636 case PCI_DEVICE_ID_TI_1251B:
637 case PCI_DEVICE_ID_TI_1420:
638 case PCI_DEVICE_ID_TI_1450:
639 case PCI_DEVICE_ID_TI_1451A:
640 case PCI_DEVICE_ID_TI_1520:
641 case PCI_DEVICE_ID_TI_1620:
642 case PCI_DEVICE_ID_TI_4520:
643 case PCI_DEVICE_ID_TI_4450:
644 case PCI_DEVICE_ID_TI_4451:
646 * there are way more, but they need to be added in yenta_socket.c
647 * and pci_ids.h first anyway.
651 case PCI_DEVICE_ID_TI_XX12:
652 case PCI_DEVICE_ID_TI_X515:
653 case PCI_DEVICE_ID_TI_X420:
654 case PCI_DEVICE_ID_TI_X620:
655 case PCI_DEVICE_ID_TI_XX21_XX11:
656 case PCI_DEVICE_ID_TI_7410:
657 case PCI_DEVICE_ID_TI_7610:
659 * those are either single or dual slot CB with additional functions
660 * like 1394, smartcard reader, etc. check the TIEALL flag for them
661 * the TIEALL flag binds the IRQ of all functions toghether.
662 * we catch the single slot variants later.
664 sysctl = config_readl(socket, TI113X_SYSTEM_CONTROL);
665 if (sysctl & TIXX21_SCR_TIEALL)
670 /* single-slot controllers have the 2nd slot empty always :) */
676 devfn = socket->dev->devfn & ~0x07;
677 func = pci_get_slot(socket->dev->bus,
678 (socket->dev->devfn & 0x07) ? devfn : devfn | 0x01);
683 * check that the device id of both slots match. this is needed for the
684 * XX21 and the XX11 controller that share the same device id for single
685 * and dual slot controllers. return '2nd slot empty'. we already checked
686 * if the interrupt is tied to another function.
688 if (socket->dev->device != func->device)
691 slot2 = pci_get_drvdata(func);
696 yenta_get_status(&slot2->socket, &state);
697 if (state & SS_DETECT) {
708 * TI specifiy parts for the power hook.
710 * some TI's with some CB's produces interrupt storm on power on. it has been
711 * seen with atheros wlan cards on TI1225 and TI1410. solution is simply to
712 * disable any CB interrupts during this time.
714 static int ti12xx_power_hook(struct pcmcia_socket *sock, int operation)
716 struct yenta_socket *socket = container_of(sock, struct yenta_socket, socket);
717 u32 mfunc, devctl, sysctl;
720 /* only POWER_PRE and POWER_POST are interesting */
721 if ((operation != HOOK_POWER_PRE) && (operation != HOOK_POWER_POST))
724 devctl = config_readb(socket, TI113X_DEVICE_CONTROL);
725 sysctl = config_readl(socket, TI113X_SYSTEM_CONTROL);
726 mfunc = config_readl(socket, TI122X_MFUNC);
729 * all serial/tied: only disable when modparm set. always doing it
730 * would mean a regression for working setups 'cos it disables the
731 * interrupts for both both slots on 2-slot controllers
732 * (and users of single slot controllers where it's save have to
733 * live with setting the modparm, most don't have to anyway)
735 if (((devctl & TI113X_DCR_IMODE_MASK) == TI12XX_DCR_IMODE_ALL_SERIAL) &&
736 (pwr_irqs_off || ti12xx_2nd_slot_empty(socket))) {
737 switch (socket->dev->device) {
738 case PCI_DEVICE_ID_TI_1250:
739 case PCI_DEVICE_ID_TI_1251A:
740 case PCI_DEVICE_ID_TI_1251B:
741 case PCI_DEVICE_ID_TI_1450:
742 case PCI_DEVICE_ID_TI_1451A:
743 case PCI_DEVICE_ID_TI_4450:
744 case PCI_DEVICE_ID_TI_4451:
745 /* these chips have no IRQSER setting in MFUNC3 */
749 if (operation == HOOK_POWER_PRE)
750 mfunc = (mfunc & ~TI122X_MFUNC3_MASK);
752 mfunc = (mfunc & ~TI122X_MFUNC3_MASK) | TI122X_MFUNC3_IRQSER;
758 /* do the job differently for func0/1 */
759 if ((PCI_FUNC(socket->dev->devfn) == 0) ||
760 ((sysctl & TI122X_SCR_INTRTIE) &&
761 (pwr_irqs_off || ti12xx_2nd_slot_empty(socket)))) {
762 /* some bridges are different */
763 switch (socket->dev->device) {
764 case PCI_DEVICE_ID_TI_1250:
765 case PCI_DEVICE_ID_TI_1251A:
766 case PCI_DEVICE_ID_TI_1251B:
767 case PCI_DEVICE_ID_TI_1450:
768 /* those oldies use gpio3 for INTA */
769 gpio3 = config_readb(socket, TI1250_GPIO3_CONTROL);
770 if (operation == HOOK_POWER_PRE)
771 gpio3 = (gpio3 & ~TI1250_GPIO_MODE_MASK) | 0x40;
773 gpio3 &= ~TI1250_GPIO_MODE_MASK;
774 config_writeb(socket, TI1250_GPIO3_CONTROL, gpio3);
778 /* all new bridges are the same */
779 if (operation == HOOK_POWER_PRE)
780 mfunc &= ~TI122X_MFUNC0_MASK;
782 mfunc |= TI122X_MFUNC0_INTA;
783 config_writel(socket, TI122X_MFUNC, mfunc);
786 switch (socket->dev->device) {
787 case PCI_DEVICE_ID_TI_1251A:
788 case PCI_DEVICE_ID_TI_1251B:
789 case PCI_DEVICE_ID_TI_1450:
790 /* those have INTA elsewhere and INTB in MFUNC0 */
791 if (operation == HOOK_POWER_PRE)
792 mfunc &= ~TI122X_MFUNC0_MASK;
794 mfunc |= TI125X_MFUNC0_INTB;
795 config_writel(socket, TI122X_MFUNC, mfunc);
800 /* all new bridges are the same */
801 if (operation == HOOK_POWER_PRE)
802 mfunc &= ~TI122X_MFUNC1_MASK;
804 mfunc |= TI122X_MFUNC1_INTB;
805 config_writel(socket, TI122X_MFUNC, mfunc);
812 static int ti12xx_override(struct yenta_socket *socket)
816 /* make sure that memory burst is active */
817 val_orig = val = config_readl(socket, TI113X_SYSTEM_CONTROL);
818 if (disable_clkrun && PCI_FUNC(socket->dev->devfn) == 0) {
819 dev_printk(KERN_INFO, &socket->dev->dev,
820 "Disabling CLKRUN feature\n");
821 val |= TI113X_SCR_KEEPCLK;
823 if (!(val & TI122X_SCR_MRBURSTUP)) {
824 dev_printk(KERN_INFO, &socket->dev->dev,
825 "Enabling burst memory read transactions\n");
826 val |= TI122X_SCR_MRBURSTUP;
829 config_writel(socket, TI113X_SYSTEM_CONTROL, val);
832 * Yenta expects controllers to use CSCINT to route
833 * CSC interrupts to PCI rather than INTVAL.
835 val = config_readb(socket, TI1250_DIAGNOSTIC);
836 dev_printk(KERN_INFO, &socket->dev->dev,
837 "Using %s to route CSC interrupts to PCI\n",
838 (val & TI1250_DIAG_PCI_CSC) ? "CSCINT" : "INTVAL");
839 dev_printk(KERN_INFO, &socket->dev->dev,
840 "Routing CardBus interrupts to %s\n",
841 (val & TI1250_DIAG_PCI_IREQ) ? "PCI" : "ISA");
843 /* do irqrouting, depending on function */
844 if (PCI_FUNC(socket->dev->devfn) == 0)
845 ti12xx_irqroute_func0(socket);
847 ti12xx_irqroute_func1(socket);
849 /* install power hook */
850 socket->socket.power_hook = ti12xx_power_hook;
852 return ti_override(socket);
856 static int ti1250_override(struct yenta_socket *socket)
860 old = config_readb(socket, TI1250_DIAGNOSTIC);
861 diag = old & ~(TI1250_DIAG_PCI_CSC | TI1250_DIAG_PCI_IREQ);
863 diag |= TI1250_DIAG_PCI_CSC | TI1250_DIAG_PCI_IREQ;
866 dev_printk(KERN_INFO, &socket->dev->dev,
867 "adjusting diagnostic: %02x -> %02x\n",
869 config_writeb(socket, TI1250_DIAGNOSTIC, diag);
872 return ti12xx_override(socket);
877 * EnE specific part. EnE bridges are register compatible with TI bridges but
878 * have their own test registers and more important their own little problems.
879 * Some fixup code to make everybody happy (TM).
882 #ifdef CONFIG_YENTA_ENE_TUNE
884 * set/clear various test bits:
885 * Defaults to clear the bit.
886 * - mask (u8) defines what bits to change
887 * - bits (u8) is the values to change them to
889 * current = (current & ~mask) | bits
891 /* pci ids of devices that wants to have the bit set */
892 #define DEVID(_vend,_dev,_subvend,_subdev,mask,bits) { \
895 .subvendor = _subvend, \
896 .subdevice = _subdev, \
897 .driver_data = ((mask) << 8 | (bits)), \
899 static struct pci_device_id ene_tune_tbl[] = {
900 /* Echo Audio products based on motorola DSP56301 and DSP56361 */
901 DEVID(PCI_VENDOR_ID_MOTOROLA, 0x1801, 0xECC0, PCI_ANY_ID,
902 ENE_TEST_C9_TLTENABLE | ENE_TEST_C9_PFENABLE, ENE_TEST_C9_TLTENABLE),
903 DEVID(PCI_VENDOR_ID_MOTOROLA, 0x3410, 0xECC0, PCI_ANY_ID,
904 ENE_TEST_C9_TLTENABLE | ENE_TEST_C9_PFENABLE, ENE_TEST_C9_TLTENABLE),
909 static void ene_tune_bridge(struct pcmcia_socket *sock, struct pci_bus *bus)
911 struct yenta_socket *socket = container_of(sock, struct yenta_socket, socket);
913 struct pci_device_id *id = NULL;
914 u8 test_c9, old_c9, mask, bits;
916 list_for_each_entry(dev, &bus->devices, bus_list) {
917 id = (struct pci_device_id *) pci_match_id(ene_tune_tbl, dev);
922 test_c9 = old_c9 = config_readb(socket, ENE_TEST_C9);
924 mask = (id->driver_data >> 8) & 0xFF;
925 bits = id->driver_data & 0xFF;
927 test_c9 = (test_c9 & ~mask) | bits;
930 /* default to clear TLTEnable bit, old behaviour */
931 test_c9 &= ~ENE_TEST_C9_TLTENABLE;
933 dev_printk(KERN_INFO, &socket->dev->dev,
934 "EnE: chaning testregister 0xC9, %02x -> %02x\n",
936 config_writeb(socket, ENE_TEST_C9, test_c9);
939 static int ene_override(struct yenta_socket *socket)
941 /* install tune_bridge() function */
942 socket->socket.tune_bridge = ene_tune_bridge;
944 return ti1250_override(socket);
947 # define ene_override ti1250_override
948 #endif /* !CONFIG_YENTA_ENE_TUNE */
950 #endif /* _LINUX_TI113X_H */