git.oblomov.eu Git - linux-2.6/blob - drivers/scsi/mesh.c

   1 /*
   2  * SCSI low-level driver for the MESH (Macintosh Enhanced SCSI Hardware)
   3  * bus adaptor found on Power Macintosh computers.
   4  * We assume the MESH is connected to a DBDMA (descriptor-based DMA)
   5  * controller.
   6  *
   7  * Paul Mackerras, August 1996.
   8  * Copyright (C) 1996 Paul Mackerras.
   9  *
  10  * Apr. 21 2002  - BenH         Rework bus reset code for new error handler
  11  *                              Add delay after initial bus reset
  12  *                              Add module parameters
  13  *
  14  * Sep. 27 2003  - BenH         Move to new driver model, fix some write posting
  15  *                              issues
  16  * To do:
  17  * - handle aborts correctly
  18  * - retry arbitration if lost (unless higher levels do this for us)
  19  * - power down the chip when no device is detected
  20  */
  21 #include <linux/config.h>
  22 #include <linux/module.h>
  23 #include <linux/kernel.h>
  24 #include <linux/delay.h>
  25 #include <linux/types.h>
  26 #include <linux/string.h>
  27 #include <linux/slab.h>
  28 #include <linux/blkdev.h>
  29 #include <linux/proc_fs.h>
  30 #include <linux/stat.h>
  31 #include <linux/interrupt.h>
  32 #include <linux/reboot.h>
  33 #include <linux/spinlock.h>
  34 #include <asm/dbdma.h>
  35 #include <asm/io.h>
  36 #include <asm/pgtable.h>
  37 #include <asm/prom.h>
  38 #include <asm/system.h>
  39 #include <asm/irq.h>
  40 #include <asm/hydra.h>
  41 #include <asm/processor.h>
  42 #include <asm/machdep.h>
  43 #include <asm/pmac_feature.h>
  44 #include <asm/pci-bridge.h>
  45 #include <asm/macio.h>
  46
  47 #include <scsi/scsi.h>
  48 #include <scsi/scsi_cmnd.h>
  49 #include <scsi/scsi_device.h>
  50 #include <scsi/scsi_host.h>
  51
  52 #include "mesh.h"
  53
  54 #if 1
  55 #undef KERN_DEBUG
  56 #define KERN_DEBUG KERN_WARNING
  57 #endif
  58
  59 MODULE_AUTHOR("Paul Mackerras (paulus@samba.org)");
  60 MODULE_DESCRIPTION("PowerMac MESH SCSI driver");
  61 MODULE_LICENSE("GPL");
  62
  63 static int sync_rate = CONFIG_SCSI_MESH_SYNC_RATE;
  64 static int sync_targets = 0xff;
  65 static int resel_targets = 0xff;
  66 static int debug_targets = 0;   /* print debug for these targets */
  67 static int init_reset_delay = CONFIG_SCSI_MESH_RESET_DELAY_MS;
  68
  69 module_param(sync_rate, int, 0);
  70 MODULE_PARM_DESC(sync_rate, "Synchronous rate (0..10, 0=async)");
  71 module_param(sync_targets, int, 0);
  72 MODULE_PARM_DESC(sync_targets, "Bitmask of targets allowed to set synchronous");
  73 module_param(resel_targets, int, 0);
  74 MODULE_PARM_DESC(resel_targets, "Bitmask of targets allowed to set disconnect");
  75 module_param(debug_targets, int, 0644);
  76 MODULE_PARM_DESC(debug_targets, "Bitmask of debugged targets");
  77 module_param(init_reset_delay, int, 0);
  78 MODULE_PARM_DESC(init_reset_delay, "Initial bus reset delay (0=no reset)");
  79
  80 static int mesh_sync_period = 100;
  81 static int mesh_sync_offset = 0;
  82 static unsigned char use_active_neg = 0;  /* bit mask for SEQ_ACTIVE_NEG if used */
  83
  84 #define ALLOW_SYNC(tgt)         ((sync_targets >> (tgt)) & 1)
  85 #define ALLOW_RESEL(tgt)        ((resel_targets >> (tgt)) & 1)
  86 #define ALLOW_DEBUG(tgt)        ((debug_targets >> (tgt)) & 1)
  87 #define DEBUG_TARGET(cmd)       ((cmd) && ALLOW_DEBUG((cmd)->device->id))
  88
  89 #undef MESH_DBG
  90 #define N_DBG_LOG       50
  91 #define N_DBG_SLOG      20
  92 #define NUM_DBG_EVENTS  13
  93 #undef  DBG_USE_TB              /* bombs on 601 */
  94
  95 struct dbglog {
  96         char    *fmt;
  97         u32     tb;
  98         u8      phase;
  99         u8      bs0;
 100         u8      bs1;
 101         u8      tgt;
 102         int     d;
 103 };
 104
 105 enum mesh_phase {
 106         idle,
 107         arbitrating,
 108         selecting,
 109         commanding,
 110         dataing,
 111         statusing,
 112         busfreeing,
 113         disconnecting,
 114         reselecting,
 115         sleeping
 116 };
 117
 118 enum msg_phase {
 119         msg_none,
 120         msg_out,
 121         msg_out_xxx,
 122         msg_out_last,
 123         msg_in,
 124         msg_in_bad,
 125 };
 126
 127 enum sdtr_phase {
 128         do_sdtr,
 129         sdtr_sent,
 130         sdtr_done
 131 };
 132
 133 struct mesh_target {
 134         enum sdtr_phase sdtr_state;
 135         int     sync_params;
 136         int     data_goes_out;          /* guess as to data direction */
 137         struct scsi_cmnd *current_req;
 138         u32     saved_ptr;
 139 #ifdef MESH_DBG
 140         int     log_ix;
 141         int     n_log;
 142         struct dbglog log[N_DBG_LOG];
 143 #endif
 144 };
 145
 146 struct mesh_state {
 147         volatile struct mesh_regs __iomem *mesh;
 148         int     meshintr;
 149         volatile struct dbdma_regs __iomem *dma;
 150         int     dmaintr;
 151         struct  Scsi_Host *host;
 152         struct  mesh_state *next;
 153         struct scsi_cmnd *request_q;
 154         struct scsi_cmnd *request_qtail;
 155         enum mesh_phase phase;          /* what we're currently trying to do */
 156         enum msg_phase msgphase;
 157         int     conn_tgt;               /* target we're connected to */
 158         struct scsi_cmnd *current_req;          /* req we're currently working on */
 159         int     data_ptr;
 160         int     dma_started;
 161         int     dma_count;
 162         int     stat;
 163         int     aborting;
 164         int     expect_reply;
 165         int     n_msgin;
 166         u8      msgin[16];
 167         int     n_msgout;
 168         int     last_n_msgout;
 169         u8      msgout[16];
 170         struct dbdma_cmd *dma_cmds;     /* space for dbdma commands, aligned */
 171         dma_addr_t dma_cmd_bus;
 172         void    *dma_cmd_space;
 173         int     dma_cmd_size;
 174         int     clk_freq;
 175         struct mesh_target tgts[8];
 176         struct macio_dev *mdev;
 177         struct pci_dev* pdev;
 178 #ifdef MESH_DBG
 179         int     log_ix;
 180         int     n_log;
 181         struct dbglog log[N_DBG_SLOG];
 182 #endif
 183 };
 184
 185 /*
 186  * Driver is too messy, we need a few prototypes...
 187  */
 188 static void mesh_done(struct mesh_state *ms, int start_next);
 189 static void mesh_interrupt(int irq, void *dev_id, struct pt_regs *ptregs);
 190 static void cmd_complete(struct mesh_state *ms);
 191 static void set_dma_cmds(struct mesh_state *ms, struct scsi_cmnd *cmd);
 192 static void halt_dma(struct mesh_state *ms);
 193 static void phase_mismatch(struct mesh_state *ms);
 194
 195
 196 /*
 197  * Some debugging & logging routines
 198  */
 199
 200 #ifdef MESH_DBG
 201
 202 static inline u32 readtb(void)
 203 {
 204         u32 tb;
 205
 206 #ifdef DBG_USE_TB
 207         /* Beware: if you enable this, it will crash on 601s. */
 208         asm ("mftb %0" : "=r" (tb) : );
 209 #else
 210         tb = 0;
 211 #endif
 212         return tb;
 213 }
 214
 215 static void dlog(struct mesh_state *ms, char *fmt, int a)
 216 {
 217         struct mesh_target *tp = &ms->tgts[ms->conn_tgt];
 218         struct dbglog *tlp, *slp;
 219
 220         tlp = &tp->log[tp->log_ix];
 221         slp = &ms->log[ms->log_ix];
 222         tlp->fmt = fmt;
 223         tlp->tb = readtb();
 224         tlp->phase = (ms->msgphase << 4) + ms->phase;
 225         tlp->bs0 = ms->mesh->bus_status0;
 226         tlp->bs1 = ms->mesh->bus_status1;
 227         tlp->tgt = ms->conn_tgt;
 228         tlp->d = a;
 229         *slp = *tlp;
 230         if (++tp->log_ix >= N_DBG_LOG)
 231                 tp->log_ix = 0;
 232         if (tp->n_log < N_DBG_LOG)
 233                 ++tp->n_log;
 234         if (++ms->log_ix >= N_DBG_SLOG)
 235                 ms->log_ix = 0;
 236         if (ms->n_log < N_DBG_SLOG)
 237                 ++ms->n_log;
 238 }
 239
 240 static void dumplog(struct mesh_state *ms, int t)
 241 {
 242         struct mesh_target *tp = &ms->tgts[t];
 243         struct dbglog *lp;
 244         int i;
 245
 246         if (tp->n_log == 0)
 247                 return;
 248         i = tp->log_ix - tp->n_log;
 249         if (i < 0)
 250                 i += N_DBG_LOG;
 251         tp->n_log = 0;
 252         do {
 253                 lp = &tp->log[i];
 254                 printk(KERN_DEBUG "mesh log %d: bs=%.2x%.2x ph=%.2x ",
 255                        t, lp->bs1, lp->bs0, lp->phase);
 256 #ifdef DBG_USE_TB
 257                 printk("tb=%10u ", lp->tb);
 258 #endif
 259                 printk(lp->fmt, lp->d);
 260                 printk("\n");
 261                 if (++i >= N_DBG_LOG)
 262                         i = 0;
 263         } while (i != tp->log_ix);
 264 }
 265
 266 static void dumpslog(struct mesh_state *ms)
 267 {
 268         struct dbglog *lp;
 269         int i;
 270
 271         if (ms->n_log == 0)
 272                 return;
 273         i = ms->log_ix - ms->n_log;
 274         if (i < 0)
 275                 i += N_DBG_SLOG;
 276         ms->n_log = 0;
 277         do {
 278                 lp = &ms->log[i];
 279                 printk(KERN_DEBUG "mesh log: bs=%.2x%.2x ph=%.2x t%d ",
 280                        lp->bs1, lp->bs0, lp->phase, lp->tgt);
 281 #ifdef DBG_USE_TB
 282                 printk("tb=%10u ", lp->tb);
 283 #endif
 284                 printk(lp->fmt, lp->d);
 285                 printk("\n");
 286                 if (++i >= N_DBG_SLOG)
 287                         i = 0;
 288         } while (i != ms->log_ix);
 289 }
 290
 291 #else
 292
 293 static inline void dlog(struct mesh_state *ms, char *fmt, int a)
 294 {}
 295 static inline void dumplog(struct mesh_state *ms, int tgt)
 296 {}
 297 static inline void dumpslog(struct mesh_state *ms)
 298 {}
 299
 300 #endif /* MESH_DBG */
 301
 302 #define MKWORD(a, b, c, d)      (((a) << 24) + ((b) << 16) + ((c) << 8) + (d))
 303
 304 static void
 305 mesh_dump_regs(struct mesh_state *ms)
 306 {
 307         volatile struct mesh_regs __iomem *mr = ms->mesh;
 308         volatile struct dbdma_regs __iomem *md = ms->dma;
 309         int t;
 310         struct mesh_target *tp;
 311
 312         printk(KERN_DEBUG "mesh: state at %p, regs at %p, dma at %p\n",
 313                ms, mr, md);
 314         printk(KERN_DEBUG "    ct=%4x seq=%2x bs=%4x fc=%2x "
 315                "exc=%2x err=%2x im=%2x int=%2x sp=%2x\n",
 316                (mr->count_hi << 8) + mr->count_lo, mr->sequence,
 317                (mr->bus_status1 << 8) + mr->bus_status0, mr->fifo_count,
 318                mr->exception, mr->error, mr->intr_mask, mr->interrupt,
 319                mr->sync_params);
 320         while(in_8(&mr->fifo_count))
 321                 printk(KERN_DEBUG " fifo data=%.2x\n",in_8(&mr->fifo));
 322         printk(KERN_DEBUG "    dma stat=%x cmdptr=%x\n",
 323                in_le32(&md->status), in_le32(&md->cmdptr));
 324         printk(KERN_DEBUG "    phase=%d msgphase=%d conn_tgt=%d data_ptr=%d\n",
 325                ms->phase, ms->msgphase, ms->conn_tgt, ms->data_ptr);
 326         printk(KERN_DEBUG "    dma_st=%d dma_ct=%d n_msgout=%d\n",
 327                ms->dma_started, ms->dma_count, ms->n_msgout);
 328         for (t = 0; t < 8; ++t) {
 329                 tp = &ms->tgts[t];
 330                 if (tp->current_req == NULL)
 331                         continue;
 332                 printk(KERN_DEBUG "    target %d: req=%p goes_out=%d saved_ptr=%d\n",
 333                        t, tp->current_req, tp->data_goes_out, tp->saved_ptr);
 334         }
 335 }
 336
 337
 338 /*
 339  * Flush write buffers on the bus path to the mesh
 340  */
 341 static inline void mesh_flush_io(volatile struct mesh_regs __iomem *mr)
 342 {
 343         (void)in_8(&mr->mesh_id);
 344 }
 345
 346
 347 /*
 348  * Complete a SCSI command
 349  */
 350 static void mesh_completed(struct mesh_state *ms, struct scsi_cmnd *cmd)
 351 {
 352         (*cmd->scsi_done)(cmd);
 353 }
 354
 355
 356 /* Called with  meshinterrupt disabled, initialize the chipset
 357  * and eventually do the initial bus reset. The lock must not be
 358  * held since we can schedule.
 359  */
 360 static void mesh_init(struct mesh_state *ms)
 361 {
 362         volatile struct mesh_regs __iomem *mr = ms->mesh;
 363         volatile struct dbdma_regs __iomem *md = ms->dma;
 364
 365         mesh_flush_io(mr);
 366         udelay(100);
 367
 368         /* Reset controller */
 369         out_le32(&md->control, (RUN|PAUSE|FLUSH|WAKE) << 16);   /* stop dma */
 370         out_8(&mr->exception, 0xff);    /* clear all exception bits */
 371         out_8(&mr->error, 0xff);        /* clear all error bits */
 372         out_8(&mr->sequence, SEQ_RESETMESH);
 373         mesh_flush_io(mr);
 374         udelay(10);
 375         out_8(&mr->intr_mask, INT_ERROR | INT_EXCEPTION | INT_CMDDONE);
 376         out_8(&mr->source_id, ms->host->this_id);
 377         out_8(&mr->sel_timeout, 25);    /* 250ms */
 378         out_8(&mr->sync_params, ASYNC_PARAMS);
 379
 380         if (init_reset_delay) {
 381                 printk(KERN_INFO "mesh: performing initial bus reset...\n");
 382
 383                 /* Reset bus */
 384                 out_8(&mr->bus_status1, BS1_RST);       /* assert RST */
 385                 mesh_flush_io(mr);
 386                 udelay(30);                     /* leave it on for >= 25us */
 387                 out_8(&mr->bus_status1, 0);     /* negate RST */
 388                 mesh_flush_io(mr);
 389
 390                 /* Wait for bus to come back */
 391                 msleep(init_reset_delay);
 392         }
 393
 394         /* Reconfigure controller */
 395         out_8(&mr->interrupt, 0xff);    /* clear all interrupt bits */
 396         out_8(&mr->sequence, SEQ_FLUSHFIFO);
 397         mesh_flush_io(mr);
 398         udelay(1);
 399         out_8(&mr->sync_params, ASYNC_PARAMS);
 400         out_8(&mr->sequence, SEQ_ENBRESEL);
 401
 402         ms->phase = idle;
 403         ms->msgphase = msg_none;
 404 }
 405
 406
 407 static void mesh_start_cmd(struct mesh_state *ms, struct scsi_cmnd *cmd)
 408 {
 409         volatile struct mesh_regs __iomem *mr = ms->mesh;
 410         int t, id;
 411
 412         id = cmd->device->id;
 413         ms->current_req = cmd;
 414         ms->tgts[id].data_goes_out = cmd->sc_data_direction == DMA_TO_DEVICE;
 415         ms->tgts[id].current_req = cmd;
 416
 417 #if 1
 418         if (DEBUG_TARGET(cmd)) {
 419                 int i;
 420                 printk(KERN_DEBUG "mesh_start: %p ser=%lu tgt=%d cmd=",
 421                        cmd, cmd->serial_number, id);
 422                 for (i = 0; i < cmd->cmd_len; ++i)
 423                         printk(" %x", cmd->cmnd[i]);
 424                 printk(" use_sg=%d buffer=%p bufflen=%u\n",
 425                        cmd->use_sg, cmd->request_buffer, cmd->request_bufflen);
 426         }
 427 #endif
 428         if (ms->dma_started)
 429                 panic("mesh: double DMA start !\n");
 430
 431         ms->phase = arbitrating;
 432         ms->msgphase = msg_none;
 433         ms->data_ptr = 0;
 434         ms->dma_started = 0;
 435         ms->n_msgout = 0;
 436         ms->last_n_msgout = 0;
 437         ms->expect_reply = 0;
 438         ms->conn_tgt = id;
 439         ms->tgts[id].saved_ptr = 0;
 440         ms->stat = DID_OK;
 441         ms->aborting = 0;
 442 #ifdef MESH_DBG
 443         ms->tgts[id].n_log = 0;
 444         dlog(ms, "start cmd=%x", (int) cmd);
 445 #endif
 446
 447         /* Off we go */
 448         dlog(ms, "about to arb, intr/exc/err/fc=%.8x",
 449              MKWORD(mr->interrupt, mr->exception, mr->error, mr->fifo_count));
 450         out_8(&mr->interrupt, INT_CMDDONE);
 451         out_8(&mr->sequence, SEQ_ENBRESEL);
 452         mesh_flush_io(mr);
 453         udelay(1);
 454
 455         if (in_8(&mr->bus_status1) & (BS1_BSY | BS1_SEL)) {
 456                 /*
 457                  * Some other device has the bus or is arbitrating for it -
 458                  * probably a target which is about to reselect us.
 459                  */
 460                 dlog(ms, "busy b4 arb, intr/exc/err/fc=%.8x",
 461                      MKWORD(mr->interrupt, mr->exception,
 462                             mr->error, mr->fifo_count));
 463                 for (t = 100; t > 0; --t) {
 464                         if ((in_8(&mr->bus_status1) & (BS1_BSY | BS1_SEL)) == 0)
 465                                 break;
 466                         if (in_8(&mr->interrupt) != 0) {
 467                                 dlog(ms, "intr b4 arb, intr/exc/err/fc=%.8x",
 468                                      MKWORD(mr->interrupt, mr->exception,
 469                                             mr->error, mr->fifo_count));
 470                                 mesh_interrupt(0, (void *)ms, NULL);
 471                                 if (ms->phase != arbitrating)
 472                                         return;
 473                         }
 474                         udelay(1);
 475                 }
 476                 if (in_8(&mr->bus_status1) & (BS1_BSY | BS1_SEL)) {
 477                         /* XXX should try again in a little while */
 478                         ms->stat = DID_BUS_BUSY;
 479                         ms->phase = idle;
 480                         mesh_done(ms, 0);
 481                         return;
 482                 }
 483         }
 484
 485         /*
 486          * Apparently the mesh has a bug where it will assert both its
 487          * own bit and the target's bit on the bus during arbitration.
 488          */
 489         out_8(&mr->dest_id, mr->source_id);
 490
 491         /*
 492          * There appears to be a race with reselection sometimes,
 493          * where a target reselects us just as we issue the
 494          * arbitrate command.  It seems that then the arbitrate
 495          * command just hangs waiting for the bus to be free
 496          * without giving us a reselection exception.
 497          * The only way I have found to get it to respond correctly
 498          * is this: disable reselection before issuing the arbitrate
 499          * command, then after issuing it, if it looks like a target
 500          * is trying to reselect us, reset the mesh and then enable
 501          * reselection.
 502          */
 503         out_8(&mr->sequence, SEQ_DISRESEL);
 504         if (in_8(&mr->interrupt) != 0) {
 505                 dlog(ms, "intr after disresel, intr/exc/err/fc=%.8x",
 506                      MKWORD(mr->interrupt, mr->exception,
 507                             mr->error, mr->fifo_count));
 508                 mesh_interrupt(0, (void *)ms, NULL);
 509                 if (ms->phase != arbitrating)
 510                         return;
 511                 dlog(ms, "after intr after disresel, intr/exc/err/fc=%.8x",
 512                      MKWORD(mr->interrupt, mr->exception,
 513                             mr->error, mr->fifo_count));
 514         }
 515
 516         out_8(&mr->sequence, SEQ_ARBITRATE);
 517
 518         for (t = 230; t > 0; --t) {
 519                 if (in_8(&mr->interrupt) != 0)
 520                         break;
 521                 udelay(1);
 522         }
 523         dlog(ms, "after arb, intr/exc/err/fc=%.8x",
 524              MKWORD(mr->interrupt, mr->exception, mr->error, mr->fifo_count));
 525         if (in_8(&mr->interrupt) == 0 && (in_8(&mr->bus_status1) & BS1_SEL)
 526             && (in_8(&mr->bus_status0) & BS0_IO)) {
 527                 /* looks like a reselection - try resetting the mesh */
 528                 dlog(ms, "resel? after arb, intr/exc/err/fc=%.8x",
 529                      MKWORD(mr->interrupt, mr->exception, mr->error, mr->fifo_count));
 530                 out_8(&mr->sequence, SEQ_RESETMESH);
 531                 mesh_flush_io(mr);
 532                 udelay(10);
 533                 out_8(&mr->interrupt, INT_ERROR | INT_EXCEPTION | INT_CMDDONE);
 534                 out_8(&mr->intr_mask, INT_ERROR | INT_EXCEPTION | INT_CMDDONE);
 535                 out_8(&mr->sequence, SEQ_ENBRESEL);
 536                 mesh_flush_io(mr);
 537                 for (t = 10; t > 0 && in_8(&mr->interrupt) == 0; --t)
 538                         udelay(1);
 539                 dlog(ms, "tried reset after arb, intr/exc/err/fc=%.8x",
 540                      MKWORD(mr->interrupt, mr->exception, mr->error, mr->fifo_count));
 541 #ifndef MESH_MULTIPLE_HOSTS
 542                 if (in_8(&mr->interrupt) == 0 && (in_8(&mr->bus_status1) & BS1_SEL)
 543                     && (in_8(&mr->bus_status0) & BS0_IO)) {
 544                         printk(KERN_ERR "mesh: controller not responding"
 545                                " to reselection!\n");
 546                         /*
 547                          * If this is a target reselecting us, and the
 548                          * mesh isn't responding, the higher levels of
 549                          * the scsi code will eventually time out and
 550                          * reset the bus.
 551                          */
 552                 }
 553 #endif
 554         }
 555 }
 556
 557 /*
 558  * Start the next command for a MESH.
 559  * Should be called with interrupts disabled.
 560  */
 561 static void mesh_start(struct mesh_state *ms)
 562 {
 563         struct scsi_cmnd *cmd, *prev, *next;
 564
 565         if (ms->phase != idle || ms->current_req != NULL) {
 566                 printk(KERN_ERR "inappropriate mesh_start (phase=%d, ms=%p)",
 567                        ms->phase, ms);
 568                 return;
 569         }
 570
 571         while (ms->phase == idle) {
 572                 prev = NULL;
 573                 for (cmd = ms->request_q; ; cmd = (struct scsi_cmnd *) cmd->host_scribble) {
 574                         if (cmd == NULL)
 575                                 return;
 576                         if (ms->tgts[cmd->device->id].current_req == NULL)
 577                                 break;
 578                         prev = cmd;
 579                 }
 580                 next = (struct scsi_cmnd *) cmd->host_scribble;
 581                 if (prev == NULL)
 582                         ms->request_q = next;
 583                 else
 584                         prev->host_scribble = (void *) next;
 585                 if (next == NULL)
 586                         ms->request_qtail = prev;
 587
 588                 mesh_start_cmd(ms, cmd);
 589         }
 590 }
 591
 592 static void mesh_done(struct mesh_state *ms, int start_next)
 593 {
 594         struct scsi_cmnd *cmd;
 595         struct mesh_target *tp = &ms->tgts[ms->conn_tgt];
 596
 597         cmd = ms->current_req;
 598         ms->current_req = NULL;
 599         tp->current_req = NULL;
 600         if (cmd) {
 601                 cmd->result = (ms->stat << 16) + cmd->SCp.Status;
 602                 if (ms->stat == DID_OK)
 603                         cmd->result += (cmd->SCp.Message << 8);
 604                 if (DEBUG_TARGET(cmd)) {
 605                         printk(KERN_DEBUG "mesh_done: result = %x, data_ptr=%d, buflen=%d\n",
 606                                cmd->result, ms->data_ptr, cmd->request_bufflen);
 607                         if ((cmd->cmnd[0] == 0 || cmd->cmnd[0] == 0x12 || cmd->cmnd[0] == 3)
 608                             && cmd->request_buffer != 0) {
 609                                 unsigned char *b = cmd->request_buffer;
 610                                 printk(KERN_DEBUG "buffer = %x %x %x %x %x %x %x %x\n",
 611                                        b[0], b[1], b[2], b[3], b[4], b[5], b[6], b[7]);
 612                         }
 613                 }
 614                 cmd->SCp.this_residual -= ms->data_ptr;
 615                 mesh_completed(ms, cmd);
 616         }
 617         if (start_next) {
 618                 out_8(&ms->mesh->sequence, SEQ_ENBRESEL);
 619                 mesh_flush_io(ms->mesh);
 620                 udelay(1);
 621                 ms->phase = idle;
 622                 mesh_start(ms);
 623         }
 624 }
 625
 626 static inline void add_sdtr_msg(struct mesh_state *ms)
 627 {
 628         int i = ms->n_msgout;
 629
 630         ms->msgout[i] = EXTENDED_MESSAGE;
 631         ms->msgout[i+1] = 3;
 632         ms->msgout[i+2] = EXTENDED_SDTR;
 633         ms->msgout[i+3] = mesh_sync_period/4;
 634         ms->msgout[i+4] = (ALLOW_SYNC(ms->conn_tgt)? mesh_sync_offset: 0);
 635         ms->n_msgout = i + 5;
 636 }
 637
 638 static void set_sdtr(struct mesh_state *ms, int period, int offset)
 639 {
 640         struct mesh_target *tp = &ms->tgts[ms->conn_tgt];
 641         volatile struct mesh_regs __iomem *mr = ms->mesh;
 642         int v, tr;
 643
 644         tp->sdtr_state = sdtr_done;
 645         if (offset == 0) {
 646                 /* asynchronous */
 647                 if (SYNC_OFF(tp->sync_params))
 648                         printk(KERN_INFO "mesh: target %d now asynchronous\n",
 649                                ms->conn_tgt);
 650                 tp->sync_params = ASYNC_PARAMS;
 651                 out_8(&mr->sync_params, ASYNC_PARAMS);
 652                 return;
 653         }
 654         /*
 655          * We need to compute ceil(clk_freq * period / 500e6) - 2
 656          * without incurring overflow.
 657          */
 658         v = (ms->clk_freq / 5000) * period;
 659         if (v <= 250000) {
 660                 /* special case: sync_period == 5 * clk_period */
 661                 v = 0;
 662                 /* units of tr are 100kB/s */
 663                 tr = (ms->clk_freq + 250000) / 500000;
 664         } else {
 665                 /* sync_period == (v + 2) * 2 * clk_period */
 666                 v = (v + 99999) / 100000 - 2;
 667                 if (v > 15)
 668                         v = 15; /* oops */
 669                 tr = ((ms->clk_freq / (v + 2)) + 199999) / 200000;
 670         }
 671         if (offset > 15)
 672                 offset = 15;    /* can't happen */
 673         tp->sync_params = SYNC_PARAMS(offset, v);
 674         out_8(&mr->sync_params, tp->sync_params);
 675         printk(KERN_INFO "mesh: target %d synchronous at %d.%d MB/s\n",
 676                ms->conn_tgt, tr/10, tr%10);
 677 }
 678
 679 static void start_phase(struct mesh_state *ms)
 680 {
 681         int i, seq, nb;
 682         volatile struct mesh_regs __iomem *mr = ms->mesh;
 683         volatile struct dbdma_regs __iomem *md = ms->dma;
 684         struct scsi_cmnd *cmd = ms->current_req;
 685         struct mesh_target *tp = &ms->tgts[ms->conn_tgt];
 686
 687         dlog(ms, "start_phase nmo/exc/fc/seq = %.8x",
 688              MKWORD(ms->n_msgout, mr->exception, mr->fifo_count, mr->sequence));
 689         out_8(&mr->interrupt, INT_ERROR | INT_EXCEPTION | INT_CMDDONE);
 690         seq = use_active_neg + (ms->n_msgout? SEQ_ATN: 0);
 691         switch (ms->msgphase) {
 692         case msg_none:
 693                 break;
 694
 695         case msg_in:
 696                 out_8(&mr->count_hi, 0);
 697                 out_8(&mr->count_lo, 1);
 698                 out_8(&mr->sequence, SEQ_MSGIN + seq);
 699                 ms->n_msgin = 0;
 700                 return;
 701
 702         case msg_out:
 703                 /*
 704                  * To make sure ATN drops before we assert ACK for
 705                  * the last byte of the message, we have to do the
 706                  * last byte specially.
 707                  */
 708                 if (ms->n_msgout <= 0) {
 709                         printk(KERN_ERR "mesh: msg_out but n_msgout=%d\n",
 710                                ms->n_msgout);
 711                         mesh_dump_regs(ms);
 712                         ms->msgphase = msg_none;
 713                         break;
 714                 }
 715                 if (ALLOW_DEBUG(ms->conn_tgt)) {
 716                         printk(KERN_DEBUG "mesh: sending %d msg bytes:",
 717                                ms->n_msgout);
 718                         for (i = 0; i < ms->n_msgout; ++i)
 719                                 printk(" %x", ms->msgout[i]);
 720                         printk("\n");
 721                 }
 722                 dlog(ms, "msgout msg=%.8x", MKWORD(ms->n_msgout, ms->msgout[0],
 723                                                 ms->msgout[1], ms->msgout[2]));
 724                 out_8(&mr->count_hi, 0);
 725                 out_8(&mr->sequence, SEQ_FLUSHFIFO);
 726                 mesh_flush_io(mr);
 727                 udelay(1);
 728                 /*
 729                  * If ATN is not already asserted, we assert it, then
 730                  * issue a SEQ_MSGOUT to get the mesh to drop ACK.
 731                  */
 732                 if ((in_8(&mr->bus_status0) & BS0_ATN) == 0) {
 733                         dlog(ms, "bus0 was %.2x explictly asserting ATN", mr->bus_status0);
 734                         out_8(&mr->bus_status0, BS0_ATN); /* explicit ATN */
 735                         mesh_flush_io(mr);
 736                         udelay(1);
 737                         out_8(&mr->count_lo, 1);
 738                         out_8(&mr->sequence, SEQ_MSGOUT + seq);
 739                         out_8(&mr->bus_status0, 0); /* release explicit ATN */
 740                         dlog(ms,"hace: after explicit ATN bus0=%.2x",mr->bus_status0);
 741                 }
 742                 if (ms->n_msgout == 1) {
 743                         /*
 744                          * We can't issue the SEQ_MSGOUT without ATN
 745                          * until the target has asserted REQ.  The logic
 746                          * in cmd_complete handles both situations:
 747                          * REQ already asserted or not.
 748                          */
 749                         cmd_complete(ms);
 750                 } else {
 751                         out_8(&mr->count_lo, ms->n_msgout - 1);
 752                         out_8(&mr->sequence, SEQ_MSGOUT + seq);
 753                         for (i = 0; i < ms->n_msgout - 1; ++i)
 754                                 out_8(&mr->fifo, ms->msgout[i]);
 755                 }
 756                 return;
 757
 758         default:
 759                 printk(KERN_ERR "mesh bug: start_phase msgphase=%d\n",
 760                        ms->msgphase);
 761         }
 762
 763         switch (ms->phase) {
 764         case selecting:
 765                 out_8(&mr->dest_id, ms->conn_tgt);
 766                 out_8(&mr->sequence, SEQ_SELECT + SEQ_ATN);
 767                 break;
 768         case commanding:
 769                 out_8(&mr->sync_params, tp->sync_params);
 770                 out_8(&mr->count_hi, 0);
 771                 if (cmd) {
 772                         out_8(&mr->count_lo, cmd->cmd_len);
 773                         out_8(&mr->sequence, SEQ_COMMAND + seq);
 774                         for (i = 0; i < cmd->cmd_len; ++i)
 775                                 out_8(&mr->fifo, cmd->cmnd[i]);
 776                 } else {
 777                         out_8(&mr->count_lo, 6);
 778                         out_8(&mr->sequence, SEQ_COMMAND + seq);
 779                         for (i = 0; i < 6; ++i)
 780                                 out_8(&mr->fifo, 0);
 781                 }
 782                 break;
 783         case dataing:
 784                 /* transfer data, if any */
 785                 if (!ms->dma_started) {
 786                         set_dma_cmds(ms, cmd);
 787                         out_le32(&md->cmdptr, virt_to_phys(ms->dma_cmds));
 788                         out_le32(&md->control, (RUN << 16) | RUN);
 789                         ms->dma_started = 1;
 790                 }
 791                 nb = ms->dma_count;
 792                 if (nb > 0xfff0)
 793                         nb = 0xfff0;
 794                 ms->dma_count -= nb;
 795                 ms->data_ptr += nb;
 796                 out_8(&mr->count_lo, nb);
 797                 out_8(&mr->count_hi, nb >> 8);
 798                 out_8(&mr->sequence, (tp->data_goes_out?
 799                                 SEQ_DATAOUT: SEQ_DATAIN) + SEQ_DMA_MODE + seq);
 800                 break;
 801         case statusing:
 802                 out_8(&mr->count_hi, 0);
 803                 out_8(&mr->count_lo, 1);
 804                 out_8(&mr->sequence, SEQ_STATUS + seq);
 805                 break;
 806         case busfreeing:
 807         case disconnecting:
 808                 out_8(&mr->sequence, SEQ_ENBRESEL);
 809                 mesh_flush_io(mr);
 810                 udelay(1);
 811                 dlog(ms, "enbresel intr/exc/err/fc=%.8x",
 812                      MKWORD(mr->interrupt, mr->exception, mr->error,
 813                             mr->fifo_count));
 814                 out_8(&mr->sequence, SEQ_BUSFREE);
 815                 break;
 816         default:
 817                 printk(KERN_ERR "mesh: start_phase called with phase=%d\n",
 818                        ms->phase);
 819                 dumpslog(ms);
 820         }
 821
 822 }
 823
 824 static inline void get_msgin(struct mesh_state *ms)
 825 {
 826         volatile struct mesh_regs __iomem *mr = ms->mesh;
 827         int i, n;
 828
 829         n = mr->fifo_count;
 830         if (n != 0) {
 831                 i = ms->n_msgin;
 832                 ms->n_msgin = i + n;
 833                 for (; n > 0; --n)
 834                         ms->msgin[i++] = in_8(&mr->fifo);
 835         }
 836 }
 837
 838 static inline int msgin_length(struct mesh_state *ms)
 839 {
 840         int b, n;
 841
 842         n = 1;
 843         if (ms->n_msgin > 0) {
 844                 b = ms->msgin[0];
 845                 if (b == 1) {
 846                         /* extended message */
 847                         n = ms->n_msgin < 2? 2: ms->msgin[1] + 2;
 848                 } else if (0x20 <= b && b <= 0x2f) {
 849                         /* 2-byte message */
 850                         n = 2;
 851                 }
 852         }
 853         return n;
 854 }
 855
 856 static void reselected(struct mesh_state *ms)
 857 {
 858         volatile struct mesh_regs __iomem *mr = ms->mesh;
 859         struct scsi_cmnd *cmd;
 860         struct mesh_target *tp;
 861         int b, t, prev;
 862
 863         switch (ms->phase) {
 864         case idle:
 865                 break;
 866         case arbitrating:
 867                 if ((cmd = ms->current_req) != NULL) {
 868                         /* put the command back on the queue */
 869                         cmd->host_scribble = (void *) ms->request_q;
 870                         if (ms->request_q == NULL)
 871                                 ms->request_qtail = cmd;
 872                         ms->request_q = cmd;
 873                         tp = &ms->tgts[cmd->device->id];
 874                         tp->current_req = NULL;
 875                 }
 876                 break;
 877         case busfreeing:
 878                 ms->phase = reselecting;
 879                 mesh_done(ms, 0);
 880                 break;
 881         case disconnecting:
 882                 break;
 883         default:
 884                 printk(KERN_ERR "mesh: reselected in phase %d/%d tgt %d\n",
 885                        ms->msgphase, ms->phase, ms->conn_tgt);
 886                 dumplog(ms, ms->conn_tgt);
 887                 dumpslog(ms);
 888         }
 889
 890         if (ms->dma_started) {
 891                 printk(KERN_ERR "mesh: reselected with DMA started !\n");
 892                 halt_dma(ms);
 893         }
 894         ms->current_req = NULL;
 895         ms->phase = dataing;
 896         ms->msgphase = msg_in;
 897         ms->n_msgout = 0;
 898         ms->last_n_msgout = 0;
 899         prev = ms->conn_tgt;
 900
 901         /*
 902          * We seem to get abortive reselections sometimes.
 903          */
 904         while ((in_8(&mr->bus_status1) & BS1_BSY) == 0) {
 905                 static int mesh_aborted_resels;
 906                 mesh_aborted_resels++;
 907                 out_8(&mr->interrupt, INT_ERROR | INT_EXCEPTION | INT_CMDDONE);
 908                 mesh_flush_io(mr);
 909                 udelay(1);
 910                 out_8(&mr->sequence, SEQ_ENBRESEL);
 911                 mesh_flush_io(mr);
 912                 udelay(5);
 913                 dlog(ms, "extra resel err/exc/fc = %.6x",
 914                      MKWORD(0, mr->error, mr->exception, mr->fifo_count));
 915         }
 916         out_8(&mr->interrupt, INT_ERROR | INT_EXCEPTION | INT_CMDDONE);
 917         mesh_flush_io(mr);
 918         udelay(1);
 919         out_8(&mr->sequence, SEQ_ENBRESEL);
 920         mesh_flush_io(mr);
 921         udelay(1);
 922         out_8(&mr->sync_params, ASYNC_PARAMS);
 923
 924         /*
 925          * Find out who reselected us.
 926          */
 927         if (in_8(&mr->fifo_count) == 0) {
 928                 printk(KERN_ERR "mesh: reselection but nothing in fifo?\n");
 929                 ms->conn_tgt = ms->host->this_id;
 930                 goto bogus;
 931         }
 932         /* get the last byte in the fifo */
 933         do {
 934                 b = in_8(&mr->fifo);
 935                 dlog(ms, "reseldata %x", b);
 936         } while (in_8(&mr->fifo_count));
 937         for (t = 0; t < 8; ++t)
 938                 if ((b & (1 << t)) != 0 && t != ms->host->this_id)
 939                         break;
 940         if (b != (1 << t) + (1 << ms->host->this_id)) {
 941                 printk(KERN_ERR "mesh: bad reselection data %x\n", b);
 942                 ms->conn_tgt = ms->host->this_id;
 943                 goto bogus;
 944         }
 945
 946
 947         /*
 948          * Set up to continue with that target's transfer.
 949          */
 950         ms->conn_tgt = t;
 951         tp = &ms->tgts[t];
 952         out_8(&mr->sync_params, tp->sync_params);
 953         if (ALLOW_DEBUG(t)) {
 954                 printk(KERN_DEBUG "mesh: reselected by target %d\n", t);
 955                 printk(KERN_DEBUG "mesh: saved_ptr=%x goes_out=%d cmd=%p\n",
 956                        tp->saved_ptr, tp->data_goes_out, tp->current_req);
 957         }
 958         ms->current_req = tp->current_req;
 959         if (tp->current_req == NULL) {
 960                 printk(KERN_ERR "mesh: reselected by tgt %d but no cmd!\n", t);
 961                 goto bogus;
 962         }
 963         ms->data_ptr = tp->saved_ptr;
 964         dlog(ms, "resel prev tgt=%d", prev);
 965         dlog(ms, "resel err/exc=%.4x", MKWORD(0, 0, mr->error, mr->exception));
 966         start_phase(ms);
 967         return;
 968
 969 bogus:
 970         dumplog(ms, ms->conn_tgt);
 971         dumpslog(ms);
 972         ms->data_ptr = 0;
 973         ms->aborting = 1;
 974         start_phase(ms);
 975 }
 976
 977 static void do_abort(struct mesh_state *ms)
 978 {
 979         ms->msgout[0] = ABORT;
 980         ms->n_msgout = 1;
 981         ms->aborting = 1;
 982         ms->stat = DID_ABORT;
 983         dlog(ms, "abort", 0);
 984 }
 985
 986 static void handle_reset(struct mesh_state *ms)
 987 {
 988         int tgt;
 989         struct mesh_target *tp;
 990         struct scsi_cmnd *cmd;
 991         volatile struct mesh_regs __iomem *mr = ms->mesh;
 992
 993         for (tgt = 0; tgt < 8; ++tgt) {
 994                 tp = &ms->tgts[tgt];
 995                 if ((cmd = tp->current_req) != NULL) {
 996                         cmd->result = DID_RESET << 16;
 997                         tp->current_req = NULL;
 998                         mesh_completed(ms, cmd);
 999                 }
1000                 ms->tgts[tgt].sdtr_state = do_sdtr;
1001                 ms->tgts[tgt].sync_params = ASYNC_PARAMS;
1002         }
1003         ms->current_req = NULL;
1004         while ((cmd = ms->request_q) != NULL) {
1005                 ms->request_q = (struct scsi_cmnd *) cmd->host_scribble;
1006                 cmd->result = DID_RESET << 16;
1007                 mesh_completed(ms, cmd);
1008         }
1009         ms->phase = idle;
1010         ms->msgphase = msg_none;
1011         out_8(&mr->interrupt, INT_ERROR | INT_EXCEPTION | INT_CMDDONE);
1012         out_8(&mr->sequence, SEQ_FLUSHFIFO);
1013         mesh_flush_io(mr);
1014         udelay(1);
1015         out_8(&mr->sync_params, ASYNC_PARAMS);
1016         out_8(&mr->sequence, SEQ_ENBRESEL);
1017 }
1018
1019 static irqreturn_t do_mesh_interrupt(int irq, void *dev_id, struct pt_regs *ptregs)
1020 {
1021         unsigned long flags;
1022         struct Scsi_Host *dev = ((struct mesh_state *)dev_id)->host;
1023
1024         spin_lock_irqsave(dev->host_lock, flags);
1025         mesh_interrupt(irq, dev_id, ptregs);
1026         spin_unlock_irqrestore(dev->host_lock, flags);
1027         return IRQ_HANDLED;
1028 }
1029
1030 static void handle_error(struct mesh_state *ms)
1031 {
1032         int err, exc, count;
1033         volatile struct mesh_regs __iomem *mr = ms->mesh;
1034
1035         err = in_8(&mr->error);
1036         exc = in_8(&mr->exception);
1037         out_8(&mr->interrupt, INT_ERROR | INT_EXCEPTION | INT_CMDDONE);
1038         dlog(ms, "error err/exc/fc/cl=%.8x",
1039              MKWORD(err, exc, mr->fifo_count, mr->count_lo));
1040         if (err & ERR_SCSIRESET) {
1041                 /* SCSI bus was reset */
1042                 printk(KERN_INFO "mesh: SCSI bus reset detected: "
1043                        "waiting for end...");
1044                 while ((in_8(&mr->bus_status1) & BS1_RST) != 0)
1045                         udelay(1);
1046                 printk("done\n");
1047                 handle_reset(ms);
1048                 /* request_q is empty, no point in mesh_start() */
1049                 return;
1050         }
1051         if (err & ERR_UNEXPDISC) {
1052                 /* Unexpected disconnect */
1053                 if (exc & EXC_RESELECTED) {
1054                         reselected(ms);
1055                         return;
1056                 }
1057                 if (!ms->aborting) {
1058                         printk(KERN_WARNING "mesh: target %d aborted\n",
1059                                ms->conn_tgt);
1060                         dumplog(ms, ms->conn_tgt);
1061                         dumpslog(ms);
1062                 }
1063                 out_8(&mr->interrupt, INT_CMDDONE);
1064                 ms->stat = DID_ABORT;
1065                 mesh_done(ms, 1);
1066                 return;
1067         }
1068         if (err & ERR_PARITY) {
1069                 if (ms->msgphase == msg_in) {
1070                         printk(KERN_ERR "mesh: msg parity error, target %d\n",
1071                                ms->conn_tgt);
1072                         ms->msgout[0] = MSG_PARITY_ERROR;
1073                         ms->n_msgout = 1;
1074                         ms->msgphase = msg_in_bad;
1075                         cmd_complete(ms);
1076                         return;
1077                 }
1078                 if (ms->stat == DID_OK) {
1079                         printk(KERN_ERR "mesh: parity error, target %d\n",
1080                                ms->conn_tgt);
1081                         ms->stat = DID_PARITY;
1082                 }
1083                 count = (mr->count_hi << 8) + mr->count_lo;
1084                 if (count == 0) {
1085                         cmd_complete(ms);
1086                 } else {
1087                         /* reissue the data transfer command */
1088                         out_8(&mr->sequence, mr->sequence);
1089                 }
1090                 return;
1091         }
1092         if (err & ERR_SEQERR) {
1093                 if (exc & EXC_RESELECTED) {
1094                         /* This can happen if we issue a command to
1095                            get the bus just after the target reselects us. */
1096                         static int mesh_resel_seqerr;
1097                         mesh_resel_seqerr++;
1098                         reselected(ms);
1099                         return;
1100                 }
1101                 if (exc == EXC_PHASEMM) {
1102                         static int mesh_phasemm_seqerr;
1103                         mesh_phasemm_seqerr++;
1104                         phase_mismatch(ms);
1105                         return;
1106                 }
1107                 printk(KERN_ERR "mesh: sequence error (err=%x exc=%x)\n",
1108                        err, exc);
1109         } else {
1110                 printk(KERN_ERR "mesh: unknown error %x (exc=%x)\n", err, exc);
1111         }
1112         mesh_dump_regs(ms);
1113         dumplog(ms, ms->conn_tgt);
1114         if (ms->phase > selecting && (in_8(&mr->bus_status1) & BS1_BSY)) {
1115                 /* try to do what the target wants */
1116                 do_abort(ms);
1117                 phase_mismatch(ms);
1118                 return;
1119         }
1120         ms->stat = DID_ERROR;
1121         mesh_done(ms, 1);
1122 }
1123
1124 static void handle_exception(struct mesh_state *ms)
1125 {
1126         int exc;
1127         volatile struct mesh_regs __iomem *mr = ms->mesh;
1128
1129         exc = in_8(&mr->exception);
1130         out_8(&mr->interrupt, INT_EXCEPTION | INT_CMDDONE);
1131         if (exc & EXC_RESELECTED) {
1132                 static int mesh_resel_exc;
1133                 mesh_resel_exc++;
1134                 reselected(ms);
1135         } else if (exc == EXC_ARBLOST) {
1136                 printk(KERN_DEBUG "mesh: lost arbitration\n");
1137                 ms->stat = DID_BUS_BUSY;
1138                 mesh_done(ms, 1);
1139         } else if (exc == EXC_SELTO) {
1140                 /* selection timed out */
1141                 ms->stat = DID_BAD_TARGET;
1142                 mesh_done(ms, 1);
1143         } else if (exc == EXC_PHASEMM) {
1144                 /* target wants to do something different:
1145                    find out what it wants and do it. */
1146                 phase_mismatch(ms);
1147         } else {
1148                 printk(KERN_ERR "mesh: can't cope with exception %x\n", exc);
1149                 mesh_dump_regs(ms);
1150                 dumplog(ms, ms->conn_tgt);
1151                 do_abort(ms);
1152                 phase_mismatch(ms);
1153         }
1154 }
1155
1156 static void handle_msgin(struct mesh_state *ms)
1157 {
1158         int i, code;
1159         struct scsi_cmnd *cmd = ms->current_req;
1160         struct mesh_target *tp = &ms->tgts[ms->conn_tgt];
1161
1162         if (ms->n_msgin == 0)
1163                 return;
1164         code = ms->msgin[0];
1165         if (ALLOW_DEBUG(ms->conn_tgt)) {
1166                 printk(KERN_DEBUG "got %d message bytes:", ms->n_msgin);
1167                 for (i = 0; i < ms->n_msgin; ++i)
1168                         printk(" %x", ms->msgin[i]);
1169                 printk("\n");
1170         }
1171         dlog(ms, "msgin msg=%.8x",
1172              MKWORD(ms->n_msgin, code, ms->msgin[1], ms->msgin[2]));
1173
1174         ms->expect_reply = 0;
1175         ms->n_msgout = 0;
1176         if (ms->n_msgin < msgin_length(ms))
1177                 goto reject;
1178         if (cmd)
1179                 cmd->SCp.Message = code;
1180         switch (code) {
1181         case COMMAND_COMPLETE:
1182                 break;
1183         case EXTENDED_MESSAGE:
1184                 switch (ms->msgin[2]) {
1185                 case EXTENDED_MODIFY_DATA_POINTER:
1186                         ms->data_ptr += (ms->msgin[3] << 24) + ms->msgin[6]
1187                                 + (ms->msgin[4] << 16) + (ms->msgin[5] << 8);
1188                         break;
1189                 case EXTENDED_SDTR:
1190                         if (tp->sdtr_state != sdtr_sent) {
1191                                 /* reply with an SDTR */
1192                                 add_sdtr_msg(ms);
1193                                 /* limit period to at least his value,
1194                                    offset to no more than his */
1195                                 if (ms->msgout[3] < ms->msgin[3])
1196                                         ms->msgout[3] = ms->msgin[3];
1197                                 if (ms->msgout[4] > ms->msgin[4])
1198                                         ms->msgout[4] = ms->msgin[4];
1199                                 set_sdtr(ms, ms->msgout[3], ms->msgout[4]);
1200                                 ms->msgphase = msg_out;
1201                         } else {
1202                                 set_sdtr(ms, ms->msgin[3], ms->msgin[4]);
1203                         }
1204                         break;
1205                 default:
1206                         goto reject;
1207                 }
1208                 break;
1209         case SAVE_POINTERS:
1210                 tp->saved_ptr = ms->data_ptr;
1211                 break;
1212         case RESTORE_POINTERS:
1213                 ms->data_ptr = tp->saved_ptr;
1214                 break;
1215         case DISCONNECT:
1216                 ms->phase = disconnecting;
1217                 break;
1218         case ABORT:
1219                 break;
1220         case MESSAGE_REJECT:
1221                 if (tp->sdtr_state == sdtr_sent)
1222                         set_sdtr(ms, 0, 0);
1223                 break;
1224         case NOP:
1225                 break;
1226         default:
1227                 if (IDENTIFY_BASE <= code && code <= IDENTIFY_BASE + 7) {
1228                         if (cmd == NULL) {
1229                                 do_abort(ms);
1230                                 ms->msgphase = msg_out;
1231                         } else if (code != cmd->device->lun + IDENTIFY_BASE) {
1232                                 printk(KERN_WARNING "mesh: lun mismatch "
1233                                        "(%d != %d) on reselection from "
1234                                        "target %d\n", code - IDENTIFY_BASE,
1235                                        cmd->device->lun, ms->conn_tgt);
1236                         }
1237                         break;
1238                 }
1239                 goto reject;
1240         }
1241         return;
1242
1243  reject:
1244         printk(KERN_WARNING "mesh: rejecting message from target %d:",
1245                ms->conn_tgt);
1246         for (i = 0; i < ms->n_msgin; ++i)
1247                 printk(" %x", ms->msgin[i]);
1248         printk("\n");
1249         ms->msgout[0] = MESSAGE_REJECT;
1250         ms->n_msgout = 1;
1251         ms->msgphase = msg_out;
1252 }
1253
1254 /*
1255  * Set up DMA commands for transferring data.
1256  */
1257 static void set_dma_cmds(struct mesh_state *ms, struct scsi_cmnd *cmd)
1258 {
1259         int i, dma_cmd, total, off, dtot;
1260         struct scatterlist *scl;
1261         struct dbdma_cmd *dcmds;
1262
1263         dma_cmd = ms->tgts[ms->conn_tgt].data_goes_out?
1264                 OUTPUT_MORE: INPUT_MORE;
1265         dcmds = ms->dma_cmds;
1266         dtot = 0;
1267         if (cmd) {
1268                 cmd->SCp.this_residual = cmd->request_bufflen;
1269                 if (cmd->use_sg > 0) {
1270                         int nseg;
1271                         total = 0;
1272                         scl = (struct scatterlist *) cmd->buffer;
1273                         off = ms->data_ptr;
1274                         nseg = pci_map_sg(ms->pdev, scl, cmd->use_sg,
1275                                           cmd->sc_data_direction);
1276                         for (i = 0; i <nseg; ++i, ++scl) {
1277                                 u32 dma_addr = sg_dma_address(scl);
1278                                 u32 dma_len = sg_dma_len(scl);
1279
1280                                 total += scl->length;
1281                                 if (off >= dma_len) {
1282                                         off -= dma_len;
1283                                         continue;
1284                                 }
1285                                 if (dma_len > 0xffff)
1286                                         panic("mesh: scatterlist element >= 64k");
1287                                 st_le16(&dcmds->req_count, dma_len - off);
1288                                 st_le16(&dcmds->command, dma_cmd);
1289                                 st_le32(&dcmds->phy_addr, dma_addr + off);
1290                                 dcmds->xfer_status = 0;
1291                                 ++dcmds;
1292                                 dtot += dma_len - off;
1293                                 off = 0;
1294                         }
1295                 } else if (ms->data_ptr < cmd->request_bufflen) {
1296                         dtot = cmd->request_bufflen - ms->data_ptr;
1297                         if (dtot > 0xffff)
1298                                 panic("mesh: transfer size >= 64k");
1299                         st_le16(&dcmds->req_count, dtot);
1300                         /* XXX Use pci DMA API here ... */
1301                         st_le32(&dcmds->phy_addr,
1302                                 virt_to_phys(cmd->request_buffer) + ms->data_ptr);
1303                         dcmds->xfer_status = 0;
1304                         ++dcmds;
1305                 }
1306         }
1307         if (dtot == 0) {
1308                 /* Either the target has overrun our buffer,
1309                    or the caller didn't provide a buffer. */
1310                 static char mesh_extra_buf[64];
1311
1312                 dtot = sizeof(mesh_extra_buf);
1313                 st_le16(&dcmds->req_count, dtot);
1314                 st_le32(&dcmds->phy_addr, virt_to_phys(mesh_extra_buf));
1315                 dcmds->xfer_status = 0;
1316                 ++dcmds;
1317         }
1318         dma_cmd += OUTPUT_LAST - OUTPUT_MORE;
1319         st_le16(&dcmds[-1].command, dma_cmd);
1320         memset(dcmds, 0, sizeof(*dcmds));
1321         st_le16(&dcmds->command, DBDMA_STOP);
1322         ms->dma_count = dtot;
1323 }
1324
1325 static void halt_dma(struct mesh_state *ms)
1326 {
1327         volatile struct dbdma_regs __iomem *md = ms->dma;
1328         volatile struct mesh_regs __iomem *mr = ms->mesh;
1329         struct scsi_cmnd *cmd = ms->current_req;
1330         int t, nb;
1331
1332         if (!ms->tgts[ms->conn_tgt].data_goes_out) {
1333                 /* wait a little while until the fifo drains */
1334                 t = 50;
1335                 while (t > 0 && in_8(&mr->fifo_count) != 0
1336                        && (in_le32(&md->status) & ACTIVE) != 0) {
1337                         --t;
1338                         udelay(1);
1339                 }
1340         }
1341         out_le32(&md->control, RUN << 16);      /* turn off RUN bit */
1342         nb = (mr->count_hi << 8) + mr->count_lo;
1343         dlog(ms, "halt_dma fc/count=%.6x",
1344              MKWORD(0, mr->fifo_count, 0, nb));
1345         if (ms->tgts[ms->conn_tgt].data_goes_out)
1346                 nb += mr->fifo_count;
1347         /* nb is the number of bytes not yet transferred
1348            to/from the target. */
1349         ms->data_ptr -= nb;
1350         dlog(ms, "data_ptr %x", ms->data_ptr);
1351         if (ms->data_ptr < 0) {
1352                 printk(KERN_ERR "mesh: halt_dma: data_ptr=%d (nb=%d, ms=%p)\n",
1353                        ms->data_ptr, nb, ms);
1354                 ms->data_ptr = 0;
1355 #ifdef MESH_DBG
1356                 dumplog(ms, ms->conn_tgt);
1357                 dumpslog(ms);
1358 #endif /* MESH_DBG */
1359         } else if (cmd && cmd->request_bufflen != 0 &&
1360                    ms->data_ptr > cmd->request_bufflen) {
1361                 printk(KERN_DEBUG "mesh: target %d overrun, "
1362                        "data_ptr=%x total=%x goes_out=%d\n",
1363                        ms->conn_tgt, ms->data_ptr, cmd->request_bufflen,
1364                        ms->tgts[ms->conn_tgt].data_goes_out);
1365         }
1366         if (cmd->use_sg != 0) {
1367                 struct scatterlist *sg;
1368                 sg = (struct scatterlist *)cmd->request_buffer;
1369                 pci_unmap_sg(ms->pdev, sg, cmd->use_sg, cmd->sc_data_direction);
1370         }
1371         ms->dma_started = 0;
1372 }
1373
1374 static void phase_mismatch(struct mesh_state *ms)
1375 {
1376         volatile struct mesh_regs __iomem *mr = ms->mesh;
1377         int phase;
1378
1379         dlog(ms, "phasemm ch/cl/seq/fc=%.8x",
1380              MKWORD(mr->count_hi, mr->count_lo, mr->sequence, mr->fifo_count));
1381         phase = in_8(&mr->bus_status0) & BS0_PHASE;
1382         if (ms->msgphase == msg_out_xxx && phase == BP_MSGOUT) {
1383                 /* output the last byte of the message, without ATN */
1384                 out_8(&mr->count_lo, 1);
1385                 out_8(&mr->sequence, SEQ_MSGOUT + use_active_neg);
1386                 mesh_flush_io(mr);
1387                 udelay(1);
1388                 out_8(&mr->fifo, ms->msgout[ms->n_msgout-1]);
1389                 ms->msgphase = msg_out_last;
1390                 return;
1391         }
1392
1393         if (ms->msgphase == msg_in) {
1394                 get_msgin(ms);
1395                 if (ms->n_msgin)
1396                         handle_msgin(ms);
1397         }
1398
1399         if (ms->dma_started)
1400                 halt_dma(ms);
1401         if (mr->fifo_count) {
1402                 out_8(&mr->sequence, SEQ_FLUSHFIFO);
1403                 mesh_flush_io(mr);
1404                 udelay(1);
1405         }
1406
1407         ms->msgphase = msg_none;
1408         switch (phase) {
1409         case BP_DATAIN:
1410                 ms->tgts[ms->conn_tgt].data_goes_out = 0;
1411                 ms->phase = dataing;
1412                 break;
1413         case BP_DATAOUT:
1414                 ms->tgts[ms->conn_tgt].data_goes_out = 1;
1415                 ms->phase = dataing;
1416                 break;
1417         case BP_COMMAND:
1418                 ms->phase = commanding;
1419                 break;
1420         case BP_STATUS:
1421                 ms->phase = statusing;
1422                 break;
1423         case BP_MSGIN:
1424                 ms->msgphase = msg_in;
1425                 ms->n_msgin = 0;
1426                 break;
1427         case BP_MSGOUT:
1428                 ms->msgphase = msg_out;
1429                 if (ms->n_msgout == 0) {
1430                         if (ms->aborting) {
1431                                 do_abort(ms);
1432                         } else {
1433                                 if (ms->last_n_msgout == 0) {
1434                                         printk(KERN_DEBUG
1435                                                "mesh: no msg to repeat\n");
1436                                         ms->msgout[0] = NOP;
1437                                         ms->last_n_msgout = 1;
1438                                 }
1439                                 ms->n_msgout = ms->last_n_msgout;
1440                         }
1441                 }
1442                 break;
1443         default:
1444                 printk(KERN_DEBUG "mesh: unknown scsi phase %x\n", phase);
1445                 ms->stat = DID_ERROR;
1446                 mesh_done(ms, 1);
1447                 return;
1448         }
1449
1450         start_phase(ms);
1451 }
1452
1453 static void cmd_complete(struct mesh_state *ms)
1454 {
1455         volatile struct mesh_regs __iomem *mr = ms->mesh;
1456         struct scsi_cmnd *cmd = ms->current_req;
1457         struct mesh_target *tp = &ms->tgts[ms->conn_tgt];
1458         int seq, n, t;
1459
1460         dlog(ms, "cmd_complete fc=%x", mr->fifo_count);
1461         seq = use_active_neg + (ms->n_msgout? SEQ_ATN: 0);
1462         switch (ms->msgphase) {
1463         case msg_out_xxx:
1464                 /* huh?  we expected a phase mismatch */
1465                 ms->n_msgin = 0;
1466                 ms->msgphase = msg_in;
1467                 /* fall through */
1468
1469         case msg_in:
1470                 /* should have some message bytes in fifo */
1471                 get_msgin(ms);
1472                 n = msgin_length(ms);
1473                 if (ms->n_msgin < n) {
1474                         out_8(&mr->count_lo, n - ms->n_msgin);
1475                         out_8(&mr->sequence, SEQ_MSGIN + seq);
1476                 } else {
1477                         ms->msgphase = msg_none;
1478                         handle_msgin(ms);
1479                         start_phase(ms);
1480                 }
1481                 break;
1482
1483         case msg_in_bad:
1484                 out_8(&mr->sequence, SEQ_FLUSHFIFO);
1485                 mesh_flush_io(mr);
1486                 udelay(1);
1487                 out_8(&mr->count_lo, 1);
1488                 out_8(&mr->sequence, SEQ_MSGIN + SEQ_ATN + use_active_neg);
1489                 break;
1490
1491         case msg_out:
1492                 /*
1493                  * To get the right timing on ATN wrt ACK, we have
1494                  * to get the MESH to drop ACK, wait until REQ gets
1495                  * asserted, then drop ATN.  To do this we first
1496                  * issue a SEQ_MSGOUT with ATN and wait for REQ,
1497                  * then change the command to a SEQ_MSGOUT w/o ATN.
1498                  * If we don't see REQ in a reasonable time, we
1499                  * change the command to SEQ_MSGIN with ATN,
1500                  * wait for the phase mismatch interrupt, then
1501                  * issue the SEQ_MSGOUT without ATN.
1502                  */
1503                 out_8(&mr->count_lo, 1);
1504                 out_8(&mr->sequence, SEQ_MSGOUT + use_active_neg + SEQ_ATN);
1505                 t = 30;         /* wait up to 30us */
1506                 while ((in_8(&mr->bus_status0) & BS0_REQ) == 0 && --t >= 0)
1507                         udelay(1);
1508                 dlog(ms, "last_mbyte err/exc/fc/cl=%.8x",
1509                      MKWORD(mr->error, mr->exception,
1510                             mr->fifo_count, mr->count_lo));
1511                 if (in_8(&mr->interrupt) & (INT_ERROR | INT_EXCEPTION)) {
1512                         /* whoops, target didn't do what we expected */
1513                         ms->last_n_msgout = ms->n_msgout;
1514                         ms->n_msgout = 0;
1515                         if (in_8(&mr->interrupt) & INT_ERROR) {
1516                                 printk(KERN_ERR "mesh: error %x in msg_out\n",
1517                                        in_8(&mr->error));
1518                                 handle_error(ms);
1519                                 return;
1520                         }
1521                         if (in_8(&mr->exception) != EXC_PHASEMM)
1522                                 printk(KERN_ERR "mesh: exc %x in msg_out\n",
1523                                        in_8(&mr->exception));
1524                         else
1525                                 printk(KERN_DEBUG "mesh: bs0=%x in msg_out\n",
1526                                        in_8(&mr->bus_status0));
1527                         handle_exception(ms);
1528                         return;
1529                 }
1530                 if (in_8(&mr->bus_status0) & BS0_REQ) {
1531                         out_8(&mr->sequence, SEQ_MSGOUT + use_active_neg);
1532                         mesh_flush_io(mr);
1533                         udelay(1);
1534                         out_8(&mr->fifo, ms->msgout[ms->n_msgout-1]);
1535                         ms->msgphase = msg_out_last;
1536                 } else {
1537                         out_8(&mr->sequence, SEQ_MSGIN + use_active_neg + SEQ_ATN);
1538                         ms->msgphase = msg_out_xxx;
1539                 }
1540                 break;
1541
1542         case msg_out_last:
1543                 ms->last_n_msgout = ms->n_msgout;
1544                 ms->n_msgout = 0;
1545                 ms->msgphase = ms->expect_reply? msg_in: msg_none;
1546                 start_phase(ms);
1547                 break;
1548
1549         case msg_none:
1550                 switch (ms->phase) {
1551                 case idle:
1552                         printk(KERN_ERR "mesh: interrupt in idle phase?\n");
1553                         dumpslog(ms);
1554                         return;
1555                 case selecting:
1556                         dlog(ms, "Selecting phase at command completion",0);
1557                         ms->msgout[0] = IDENTIFY(ALLOW_RESEL(ms->conn_tgt),
1558                                                  (cmd? cmd->device->lun: 0));
1559                         ms->n_msgout = 1;
1560                         ms->expect_reply = 0;
1561                         if (ms->aborting) {
1562                                 ms->msgout[0] = ABORT;
1563                                 ms->n_msgout++;
1564                         } else if (tp->sdtr_state == do_sdtr) {
1565                                 /* add SDTR message */
1566                                 add_sdtr_msg(ms);
1567                                 ms->expect_reply = 1;
1568                                 tp->sdtr_state = sdtr_sent;
1569                         }
1570                         ms->msgphase = msg_out;
1571                         /*
1572                          * We need to wait for REQ before dropping ATN.
1573                          * We wait for at most 30us, then fall back to
1574                          * a scheme where we issue a SEQ_COMMAND with ATN,
1575                          * which will give us a phase mismatch interrupt
1576                          * when REQ does come, and then we send the message.
1577                          */
1578                         t = 230;                /* wait up to 230us */
1579                         while ((in_8(&mr->bus_status0) & BS0_REQ) == 0) {
1580                                 if (--t < 0) {
1581                                         dlog(ms, "impatient for req", ms->n_msgout);
1582                                         ms->msgphase = msg_none;
1583                                         break;
1584                                 }
1585                                 udelay(1);
1586                         }
1587                         break;
1588                 case dataing:
1589                         if (ms->dma_count != 0) {
1590                                 start_phase(ms);
1591                                 return;
1592                         }
1593                         /*
1594                          * We can get a phase mismatch here if the target
1595                          * changes to the status phase, even though we have
1596                          * had a command complete interrupt.  Then, if we
1597                          * issue the SEQ_STATUS command, we'll get a sequence
1598                          * error interrupt.  Which isn't so bad except that
1599                          * occasionally the mesh actually executes the
1600                          * SEQ_STATUS *as well as* giving us the sequence
1601                          * error and phase mismatch exception.
1602                          */
1603                         out_8(&mr->sequence, 0);
1604                         out_8(&mr->interrupt,
1605                               INT_ERROR | INT_EXCEPTION | INT_CMDDONE);
1606                         halt_dma(ms);
1607                         break;
1608                 case statusing:
1609                         if (cmd) {
1610                                 cmd->SCp.Status = mr->fifo;
1611                                 if (DEBUG_TARGET(cmd))
1612                                         printk(KERN_DEBUG "mesh: status is %x\n",
1613                                                cmd->SCp.Status);
1614                         }
1615                         ms->msgphase = msg_in;
1616                         break;
1617                 case busfreeing:
1618                         mesh_done(ms, 1);
1619                         return;
1620                 case disconnecting:
1621                         ms->current_req = NULL;
1622                         ms->phase = idle;
1623                         mesh_start(ms);
1624                         return;
1625                 default:
1626                         break;
1627                 }
1628                 ++ms->phase;
1629                 start_phase(ms);
1630                 break;
1631         }
1632 }
1633
1634
1635 /*
1636  * Called by midlayer with host locked to queue a new
1637  * request
1638  */
1639 static int mesh_queue(struct scsi_cmnd *cmd, void (*done)(struct scsi_cmnd *))
1640 {
1641         struct mesh_state *ms;
1642
1643         cmd->scsi_done = done;
1644         cmd->host_scribble = NULL;
1645
1646         ms = (struct mesh_state *) cmd->device->host->hostdata;
1647
1648         if (ms->request_q == NULL)
1649                 ms->request_q = cmd;
1650         else
1651                 ms->request_qtail->host_scribble = (void *) cmd;
1652         ms->request_qtail = cmd;
1653
1654         if (ms->phase == idle)
1655                 mesh_start(ms);
1656
1657         return 0;
1658 }
1659
1660 /*
1661  * Called to handle interrupts, either call by the interrupt
1662  * handler (do_mesh_interrupt) or by other functions in
1663  * exceptional circumstances
1664  */
1665 static void mesh_interrupt(int irq, void *dev_id, struct pt_regs *ptregs)
1666 {
1667         struct mesh_state *ms = (struct mesh_state *) dev_id;
1668         volatile struct mesh_regs __iomem *mr = ms->mesh;
1669         int intr;
1670
1671 #if 0
1672         if (ALLOW_DEBUG(ms->conn_tgt))
1673                 printk(KERN_DEBUG "mesh_intr, bs0=%x int=%x exc=%x err=%x "
1674                        "phase=%d msgphase=%d\n", mr->bus_status0,
1675                        mr->interrupt, mr->exception, mr->error,
1676                        ms->phase, ms->msgphase);
1677 #endif
1678         while ((intr = in_8(&mr->interrupt)) != 0) {
1679                 dlog(ms, "interrupt intr/err/exc/seq=%.8x",
1680                      MKWORD(intr, mr->error, mr->exception, mr->sequence));
1681                 if (intr & INT_ERROR) {
1682                         handle_error(ms);
1683                 } else if (intr & INT_EXCEPTION) {
1684                         handle_exception(ms);
1685                 } else if (intr & INT_CMDDONE) {
1686                         out_8(&mr->interrupt, INT_CMDDONE);
1687                         cmd_complete(ms);
1688                 }
1689         }
1690 }
1691
1692 /* Todo: here we can at least try to remove the command from the
1693  * queue if it isn't connected yet, and for pending command, assert
1694  * ATN until the bus gets freed.
1695  */
1696 static int mesh_abort(struct scsi_cmnd *cmd)
1697 {
1698         struct mesh_state *ms = (struct mesh_state *) cmd->device->host->hostdata;
1699
1700         printk(KERN_DEBUG "mesh_abort(%p)\n", cmd);
1701         mesh_dump_regs(ms);
1702         dumplog(ms, cmd->device->id);
1703         dumpslog(ms);
1704         return FAILED;
1705 }
1706
1707 /*
1708  * Called by the midlayer with the lock held to reset the
1709  * SCSI host and bus.
1710  * The midlayer will wait for devices to come back, we don't need
1711  * to do that ourselves
1712  */
1713 static int mesh_host_reset(struct scsi_cmnd *cmd)
1714 {
1715         struct mesh_state *ms = (struct mesh_state *) cmd->device->host->hostdata;
1716         volatile struct mesh_regs __iomem *mr = ms->mesh;
1717         volatile struct dbdma_regs __iomem *md = ms->dma;
1718         unsigned long flags;
1719
1720         printk(KERN_DEBUG "mesh_host_reset\n");
1721
1722         spin_lock_irqsave(ms->host->host_lock, flags);
1723
1724         /* Reset the controller & dbdma channel */
1725         out_le32(&md->control, (RUN|PAUSE|FLUSH|WAKE) << 16);   /* stop dma */
1726         out_8(&mr->exception, 0xff);    /* clear all exception bits */
1727         out_8(&mr->error, 0xff);        /* clear all error bits */
1728         out_8(&mr->sequence, SEQ_RESETMESH);
1729         mesh_flush_io(mr);
1730         udelay(1);
1731         out_8(&mr->intr_mask, INT_ERROR | INT_EXCEPTION | INT_CMDDONE);
1732         out_8(&mr->source_id, ms->host->this_id);
1733         out_8(&mr->sel_timeout, 25);    /* 250ms */
1734         out_8(&mr->sync_params, ASYNC_PARAMS);
1735
1736         /* Reset the bus */
1737         out_8(&mr->bus_status1, BS1_RST);       /* assert RST */
1738         mesh_flush_io(mr);
1739         udelay(30);                     /* leave it on for >= 25us */
1740         out_8(&mr->bus_status1, 0);     /* negate RST */
1741
1742         /* Complete pending commands */
1743         handle_reset(ms);
1744
1745         spin_unlock_irqrestore(ms->host->host_lock, flags);
1746         return SUCCESS;
1747 }
1748
1749 static void set_mesh_power(struct mesh_state *ms, int state)
1750 {
1751         if (_machine != _MACH_Pmac)
1752                 return;
1753         if (state) {
1754                 pmac_call_feature(PMAC_FTR_MESH_ENABLE, macio_get_of_node(ms->mdev), 0, 1);
1755                 msleep(200);
1756         } else {
1757                 pmac_call_feature(PMAC_FTR_MESH_ENABLE, macio_get_of_node(ms->mdev), 0, 0);
1758                 msleep(10);
1759         }
1760 }
1761
1762
1763 #ifdef CONFIG_PM
1764 static int mesh_suspend(struct macio_dev *mdev, pm_message_t state)
1765 {
1766         struct mesh_state *ms = (struct mesh_state *)macio_get_drvdata(mdev);
1767         unsigned long flags;
1768
1769         if (state.event == mdev->ofdev.dev.power.power_state.event || state.event < 2)
1770                 return 0;
1771
1772         scsi_block_requests(ms->host);
1773         spin_lock_irqsave(ms->host->host_lock, flags);
1774         while(ms->phase != idle) {
1775                 spin_unlock_irqrestore(ms->host->host_lock, flags);
1776                 msleep(10);
1777                 spin_lock_irqsave(ms->host->host_lock, flags);
1778         }
1779         ms->phase = sleeping;
1780         spin_unlock_irqrestore(ms->host->host_lock, flags);
1781         disable_irq(ms->meshintr);
1782         set_mesh_power(ms, 0);
1783
1784         mdev->ofdev.dev.power.power_state = state;
1785
1786         return 0;
1787 }
1788
1789 static int mesh_resume(struct macio_dev *mdev)
1790 {
1791         struct mesh_state *ms = (struct mesh_state *)macio_get_drvdata(mdev);
1792         unsigned long flags;
1793
1794         if (mdev->ofdev.dev.power.power_state.event == PM_EVENT_ON)
1795                 return 0;
1796
1797         set_mesh_power(ms, 1);
1798         mesh_init(ms);
1799         spin_lock_irqsave(ms->host->host_lock, flags);
1800         mesh_start(ms);
1801         spin_unlock_irqrestore(ms->host->host_lock, flags);
1802         enable_irq(ms->meshintr);
1803         scsi_unblock_requests(ms->host);
1804
1805         mdev->ofdev.dev.power.power_state.event = PM_EVENT_ON;
1806
1807         return 0;
1808 }
1809
1810 #endif /* CONFIG_PM */
1811
1812 /*
1813  * If we leave drives set for synchronous transfers (especially
1814  * CDROMs), and reboot to MacOS, it gets confused, poor thing.
1815  * So, on reboot we reset the SCSI bus.
1816  */
1817 static int mesh_shutdown(struct macio_dev *mdev)
1818 {
1819         struct mesh_state *ms = (struct mesh_state *)macio_get_drvdata(mdev);
1820         volatile struct mesh_regs __iomem *mr;
1821         unsigned long flags;
1822
1823         printk(KERN_INFO "resetting MESH scsi bus(es)\n");
1824         spin_lock_irqsave(ms->host->host_lock, flags);
1825         mr = ms->mesh;
1826         out_8(&mr->intr_mask, 0);
1827         out_8(&mr->interrupt, INT_ERROR | INT_EXCEPTION | INT_CMDDONE);
1828         out_8(&mr->bus_status1, BS1_RST);
1829         mesh_flush_io(mr);
1830         udelay(30);
1831         out_8(&mr->bus_status1, 0);
1832         spin_unlock_irqrestore(ms->host->host_lock, flags);
1833
1834         return 0;
1835 }
1836
1837 static struct scsi_host_template mesh_template = {
1838         .proc_name                      = "mesh",
1839         .name                           = "MESH",
1840         .queuecommand                   = mesh_queue,
1841         .eh_abort_handler               = mesh_abort,
1842         .eh_host_reset_handler          = mesh_host_reset,
1843         .can_queue                      = 20,
1844         .this_id                        = 7,
1845         .sg_tablesize                   = SG_ALL,
1846         .cmd_per_lun                    = 2,
1847         .use_clustering                 = DISABLE_CLUSTERING,
1848 };
1849
1850 static int mesh_probe(struct macio_dev *mdev, const struct of_device_id *match)
1851 {
1852         struct device_node *mesh = macio_get_of_node(mdev);
1853         struct pci_dev* pdev = macio_get_pci_dev(mdev);
1854         int tgt, *cfp, minper;
1855         struct mesh_state *ms;
1856         struct Scsi_Host *mesh_host;
1857         void *dma_cmd_space;
1858         dma_addr_t dma_cmd_bus;
1859
1860         switch (mdev->bus->chip->type) {
1861         case macio_heathrow:
1862         case macio_gatwick:
1863         case macio_paddington:
1864                 use_active_neg = 0;
1865                 break;
1866         default:
1867                 use_active_neg = SEQ_ACTIVE_NEG;
1868         }
1869
1870         if (macio_resource_count(mdev) != 2 || macio_irq_count(mdev) != 2) {
1871                 printk(KERN_ERR "mesh: expected 2 addrs and 2 intrs"
1872                        " (got %d,%d)\n", mesh->n_addrs, mesh->n_intrs);
1873                 return -ENODEV;
1874         }
1875
1876         if (macio_request_resources(mdev, "mesh") != 0) {
1877                 printk(KERN_ERR "mesh: unable to request memory resources");
1878                 return -EBUSY;
1879         }
1880         mesh_host = scsi_host_alloc(&mesh_template, sizeof(struct mesh_state));
1881         if (mesh_host == NULL) {
1882                 printk(KERN_ERR "mesh: couldn't register host");
1883                 goto out_release;
1884         }
1885
1886         /* Old junk for root discovery, that will die ultimately */
1887 #if !defined(MODULE)
1888         note_scsi_host(mesh, mesh_host);
1889 #endif
1890
1891         mesh_host->base = macio_resource_start(mdev, 0);
1892         mesh_host->irq = macio_irq(mdev, 0);
1893         ms = (struct mesh_state *) mesh_host->hostdata;
1894         macio_set_drvdata(mdev, ms);
1895         ms->host = mesh_host;
1896         ms->mdev = mdev;
1897         ms->pdev = pdev;
1898
1899         ms->mesh = ioremap(macio_resource_start(mdev, 0), 0x1000);
1900         if (ms->mesh == NULL) {
1901                 printk(KERN_ERR "mesh: can't map registers\n");
1902                 goto out_free;
1903         }
1904         ms->dma = ioremap(macio_resource_start(mdev, 1), 0x1000);
1905         if (ms->dma == NULL) {
1906                 printk(KERN_ERR "mesh: can't map registers\n");
1907                 iounmap(ms->mesh);
1908                 goto out_free;
1909         }
1910
1911         ms->meshintr = macio_irq(mdev, 0);
1912         ms->dmaintr = macio_irq(mdev, 1);
1913
1914         /* Space for dma command list: +1 for stop command,
1915          * +1 to allow for aligning.
1916          */
1917         ms->dma_cmd_size = (mesh_host->sg_tablesize + 2) * sizeof(struct dbdma_cmd);
1918
1919         /* We use the PCI APIs for now until the generic one gets fixed
1920          * enough or until we get some macio-specific versions
1921          */
1922         dma_cmd_space = pci_alloc_consistent(macio_get_pci_dev(mdev),
1923                                              ms->dma_cmd_size,
1924                                              &dma_cmd_bus);
1925         if (dma_cmd_space == NULL) {
1926                 printk(KERN_ERR "mesh: can't allocate DMA table\n");
1927                 goto out_unmap;
1928         }
1929         memset(dma_cmd_space, 0, ms->dma_cmd_size);
1930
1931         ms->dma_cmds = (struct dbdma_cmd *) DBDMA_ALIGN(dma_cmd_space);
1932         ms->dma_cmd_space = dma_cmd_space;
1933         ms->dma_cmd_bus = dma_cmd_bus + ((unsigned long)ms->dma_cmds)
1934                 - (unsigned long)dma_cmd_space;
1935         ms->current_req = NULL;
1936         for (tgt = 0; tgt < 8; ++tgt) {
1937                 ms->tgts[tgt].sdtr_state = do_sdtr;
1938                 ms->tgts[tgt].sync_params = ASYNC_PARAMS;
1939                 ms->tgts[tgt].current_req = NULL;
1940         }
1941
1942         if ((cfp = (int *) get_property(mesh, "clock-frequency", NULL)))
1943                 ms->clk_freq = *cfp;
1944         else {
1945                 printk(KERN_INFO "mesh: assuming 50MHz clock frequency\n");
1946                 ms->clk_freq = 50000000;
1947         }
1948
1949         /* The maximum sync rate is clock / 5; increase
1950          * mesh_sync_period if necessary.
1951          */
1952         minper = 1000000000 / (ms->clk_freq / 5); /* ns */
1953         if (mesh_sync_period < minper)
1954                 mesh_sync_period = minper;
1955
1956         /* Power up the chip */
1957         set_mesh_power(ms, 1);
1958
1959         /* Set it up */
1960         mesh_init(ms);
1961
1962         /* Request interrupt */
1963         if (request_irq(ms->meshintr, do_mesh_interrupt, 0, "MESH", ms)) {
1964                 printk(KERN_ERR "MESH: can't get irq %d\n", ms->meshintr);
1965                 goto out_shutdown;
1966         }
1967
1968         /* Add scsi host & scan */
1969         if (scsi_add_host(mesh_host, &mdev->ofdev.dev))
1970                 goto out_release_irq;
1971         scsi_scan_host(mesh_host);
1972
1973         return 0;
1974
1975  out_release_irq:
1976         free_irq(ms->meshintr, ms);
1977  out_shutdown:
1978         /* shutdown & reset bus in case of error or macos can be confused
1979          * at reboot if the bus was set to synchronous mode already
1980          */
1981         mesh_shutdown(mdev);
1982         set_mesh_power(ms, 0);
1983         pci_free_consistent(macio_get_pci_dev(mdev), ms->dma_cmd_size,
1984                             ms->dma_cmd_space, ms->dma_cmd_bus);
1985  out_unmap:
1986         iounmap(ms->dma);
1987         iounmap(ms->mesh);
1988  out_free:
1989         scsi_host_put(mesh_host);
1990  out_release:
1991         macio_release_resources(mdev);
1992
1993         return -ENODEV;
1994 }
1995
1996 static int mesh_remove(struct macio_dev *mdev)
1997 {
1998         struct mesh_state *ms = (struct mesh_state *)macio_get_drvdata(mdev);
1999         struct Scsi_Host *mesh_host = ms->host;
2000
2001         scsi_remove_host(mesh_host);
2002
2003         free_irq(ms->meshintr, ms);
2004
2005         /* Reset scsi bus */
2006         mesh_shutdown(mdev);
2007
2008         /* Shut down chip & termination */
2009         set_mesh_power(ms, 0);
2010
2011         /* Unmap registers & dma controller */
2012         iounmap(ms->mesh);
2013         iounmap(ms->dma);
2014
2015         /* Free DMA commands memory */
2016         pci_free_consistent(macio_get_pci_dev(mdev), ms->dma_cmd_size,
2017                             ms->dma_cmd_space, ms->dma_cmd_bus);
2018
2019         /* Release memory resources */
2020         macio_release_resources(mdev);
2021
2022         scsi_host_put(mesh_host);
2023
2024         return 0;
2025 }
2026
2027
2028 static struct of_device_id mesh_match[] =
2029 {
2030         {
2031         .name           = "mesh",
2032         },
2033         {
2034         .type           = "scsi",
2035         .compatible     = "chrp,mesh0"
2036         },
2037         {},
2038 };
2039 MODULE_DEVICE_TABLE (of, mesh_match);
2040
2041 static struct macio_driver mesh_driver =
2042 {
2043         .name           = "mesh",
2044         .match_table    = mesh_match,
2045         .probe          = mesh_probe,
2046         .remove         = mesh_remove,
2047         .shutdown       = mesh_shutdown,
2048 #ifdef CONFIG_PM
2049         .suspend        = mesh_suspend,
2050         .resume         = mesh_resume,
2051 #endif
2052 };
2053
2054
2055 static int __init init_mesh(void)
2056 {
2057
2058         /* Calculate sync rate from module parameters */
2059         if (sync_rate > 10)
2060                 sync_rate = 10;
2061         if (sync_rate > 0) {
2062                 printk(KERN_INFO "mesh: configured for synchronous %d MB/s\n", sync_rate);
2063                 mesh_sync_period = 1000 / sync_rate;    /* ns */
2064                 mesh_sync_offset = 15;
2065         } else
2066                 printk(KERN_INFO "mesh: configured for asynchronous\n");
2067
2068         return macio_register_driver(&mesh_driver);
2069 }
2070
2071 static void __exit exit_mesh(void)
2072 {
2073         return macio_unregister_driver(&mesh_driver);
2074 }
2075
2076 module_init(init_mesh);
2077 module_exit(exit_mesh);