git.oblomov.eu Git - linux-2.6/blob - arch/arm/mach-pxa/pcm990-baseboard.c

   1 /*
   2  *  arch/arm/mach-pxa/pcm990-baseboard.c
   3  *  Support for the Phytec phyCORE-PXA270 Development Platform (PCM-990).
   4  *
   5  *  Refer
   6  *   http://www.phytec.com/products/rdk/ARM-XScale/phyCORE-XScale-PXA270.html
   7  *  for additional hardware info
   8  *
   9  *  Author:     Juergen Kilb
  10  *  Created:    April 05, 2005
  11  *  Copyright:  Phytec Messtechnik GmbH
  12  *  e-Mail:     armlinux@phytec.de
  13  *
  14  *  based on Intel Mainstone Board
  15  *
  16  *  Copyright 2007 Juergen Beisert @ Pengutronix (j.beisert@pengutronix.de)
  17  *
  18  *  This program is free software; you can redistribute it and/or modify
  19  *  it under the terms of the GNU General Public License version 2 as
  20  *  published by the Free Software Foundation.
  21  */
  22
  23 #include <linux/irq.h>
  24 #include <linux/platform_device.h>
  25 #include <linux/ide.h>
  26 #include <linux/i2c.h>
  27 #include <linux/pwm_backlight.h>
  28
  29 #include <media/soc_camera.h>
  30
  31 #include <asm/gpio.h>
  32 #include <asm/arch/i2c.h>
  33 #include <asm/arch/camera.h>
  34 #include <asm/mach/map.h>
  35 #include <asm/arch/pxa-regs.h>
  36 #include <asm/arch/audio.h>
  37 #include <asm/arch/mmc.h>
  38 #include <asm/arch/ohci.h>
  39 #include <asm/arch/pcm990_baseboard.h>
  40 #include <asm/arch/pxafb.h>
  41 #include <asm/arch/mfp-pxa27x.h>
  42
  43 #include "devices.h"
  44 #include "generic.h"
  45
  46 static unsigned long pcm990_pin_config[] __initdata = {
  47         /* MMC */
  48         GPIO32_MMC_CLK,
  49         GPIO112_MMC_CMD,
  50         GPIO92_MMC_DAT_0,
  51         GPIO109_MMC_DAT_1,
  52         GPIO110_MMC_DAT_2,
  53         GPIO111_MMC_DAT_3,
  54         /* USB */
  55         GPIO88_USBH1_PWR,
  56         GPIO89_USBH1_PEN,
  57         /* PWM0 */
  58         GPIO16_PWM0_OUT,
  59 };
  60
  61 /*
  62  * pcm990_lcd_power - control power supply to the LCD
  63  * @on: 0 = switch off, 1 = switch on
  64  *
  65  * Called by the pxafb driver
  66  */
  67 #ifndef CONFIG_PCM990_DISPLAY_NONE
  68 static void pcm990_lcd_power(int on, struct fb_var_screeninfo *var)
  69 {
  70         if (on) {
  71                 /* enable LCD-Latches
  72                  * power on LCD
  73                  */
  74                 __PCM990_CTRL_REG(PCM990_CTRL_PHYS + PCM990_CTRL_REG3) =
  75                         PCM990_CTRL_LCDPWR + PCM990_CTRL_LCDON;
  76         } else {
  77                 /* disable LCD-Latches
  78                  * power off LCD
  79                  */
  80                 __PCM990_CTRL_REG(PCM990_CTRL_PHYS + PCM990_CTRL_REG3) = 0x00;
  81         }
  82 }
  83 #endif
  84
  85 #if defined(CONFIG_PCM990_DISPLAY_SHARP)
  86 static struct pxafb_mode_info fb_info_sharp_lq084v1dg21 = {
  87         .pixclock               = 28000,
  88         .xres                   = 640,
  89         .yres                   = 480,
  90         .bpp                    = 16,
  91         .hsync_len              = 20,
  92         .left_margin            = 103,
  93         .right_margin           = 47,
  94         .vsync_len              = 6,
  95         .upper_margin           = 28,
  96         .lower_margin           = 5,
  97         .sync                   = 0,
  98         .cmap_greyscale         = 0,
  99 };
 100
 101 static struct pxafb_mach_info pcm990_fbinfo __initdata = {
 102         .modes                  = &fb_info_sharp_lq084v1dg21,
 103         .num_modes              = 1,
 104         .lccr0                  = LCCR0_PAS,
 105         .lccr3                  = LCCR3_PCP,
 106         .pxafb_lcd_power        = pcm990_lcd_power,
 107 };
 108 #elif defined(CONFIG_PCM990_DISPLAY_NEC)
 109 struct pxafb_mode_info fb_info_nec_nl6448bc20_18d = {
 110         .pixclock               = 39720,
 111         .xres                   = 640,
 112         .yres                   = 480,
 113         .bpp                    = 16,
 114         .hsync_len              = 32,
 115         .left_margin            = 16,
 116         .right_margin           = 48,
 117         .vsync_len              = 2,
 118         .upper_margin           = 12,
 119         .lower_margin           = 17,
 120         .sync                   = 0,
 121         .cmap_greyscale         = 0,
 122 };
 123
 124 static struct pxafb_mach_info pcm990_fbinfo __initdata = {
 125         .modes                  = &fb_info_nec_nl6448bc20_18d,
 126         .num_modes              = 1,
 127         .lccr0                  = LCCR0_Act,
 128         .lccr3                  = LCCR3_PixFlEdg,
 129         .pxafb_lcd_power        = pcm990_lcd_power,
 130 };
 131 #endif
 132
 133 static struct platform_pwm_backlight_data pcm990_backlight_data = {
 134         .pwm_id         = 0,
 135         .max_brightness = 1023,
 136         .dft_brightness = 1023,
 137         .pwm_period_ns  = 78770,
 138 };
 139
 140 static struct platform_device pcm990_backlight_device = {
 141         .name           = "pwm-backlight",
 142         .dev            = {
 143                 .parent = &pxa27x_device_pwm0.dev,
 144                 .platform_data = &pcm990_backlight_data,
 145         },
 146 };
 147
 148 /*
 149  * The PCM-990 development baseboard uses PCM-027's hardware in the
 150  * following way:
 151  *
 152  * - LCD support is in use
 153  *  - GPIO16 is output for back light on/off with PWM
 154  *  - GPIO58 ... GPIO73 are outputs for display data
 155  *  - GPIO74 is output output for LCDFCLK
 156  *  - GPIO75 is output for LCDLCLK
 157  *  - GPIO76 is output for LCDPCLK
 158  *  - GPIO77 is output for LCDBIAS
 159  * - MMC support is in use
 160  *  - GPIO32 is output for MMCCLK
 161  *  - GPIO92 is MMDAT0
 162  *  - GPIO109 is MMDAT1
 163  *  - GPIO110 is MMCS0
 164  *  - GPIO111 is MMCS1
 165  *  - GPIO112 is MMCMD
 166  * - IDE/CF card is in use
 167  *  - GPIO48 is output /POE
 168  *  - GPIO49 is output /PWE
 169  *  - GPIO50 is output /PIOR
 170  *  - GPIO51 is output /PIOW
 171  *  - GPIO54 is output /PCE2
 172  *  - GPIO55 is output /PREG
 173  *  - GPIO56 is input /PWAIT
 174  *  - GPIO57 is output /PIOS16
 175  *  - GPIO79 is output PSKTSEL
 176  *  - GPIO85 is output /PCE1
 177  * - FFUART is in use
 178  *  - GPIO34 is input FFRXD
 179  *  - GPIO35 is input FFCTS
 180  *  - GPIO36 is input FFDCD
 181  *  - GPIO37 is input FFDSR
 182  *  - GPIO38 is input FFRI
 183  *  - GPIO39 is output FFTXD
 184  *  - GPIO40 is output FFDTR
 185  *  - GPIO41 is output FFRTS
 186  * - BTUART is in use
 187  *  - GPIO42 is input BTRXD
 188  *  - GPIO43 is output BTTXD
 189  *  - GPIO44 is input BTCTS
 190  *  - GPIO45 is output BTRTS
 191  * - IRUART is in use
 192  *  - GPIO46 is input STDRXD
 193  *  - GPIO47 is output STDTXD
 194  * - AC97 is in use*)
 195  *  - GPIO28 is input AC97CLK
 196  *  - GPIO29 is input AC97DatIn
 197  *  - GPIO30 is output AC97DatO
 198  *  - GPIO31 is output AC97SYNC
 199  *  - GPIO113 is output AC97_RESET
 200  * - SSP is in use
 201  *  - GPIO23 is output SSPSCLK
 202  *  - GPIO24 is output chip select to Max7301
 203  *  - GPIO25 is output SSPTXD
 204  *  - GPIO26 is input SSPRXD
 205  *  - GPIO27 is input for Max7301 IRQ
 206  *  - GPIO53 is input SSPSYSCLK
 207  * - SSP3 is in use
 208  *  - GPIO81 is output SSPTXD3
 209  *  - GPIO82 is input SSPRXD3
 210  *  - GPIO83 is output SSPSFRM
 211  *  - GPIO84 is output SSPCLK3
 212  *
 213  * Otherwise claimed GPIOs:
 214  * GPIO1 -> IRQ from user switch
 215  * GPIO9 -> IRQ from power management
 216  * GPIO10 -> IRQ from WML9712 AC97 controller
 217  * GPIO11 -> IRQ from IDE controller
 218  * GPIO12 -> IRQ from CF controller
 219  * GPIO13 -> IRQ from CF controller
 220  * GPIO14 -> GPIO free
 221  * GPIO15 -> /CS1 selects baseboard's Control CPLD (U7, 16 bit wide data path)
 222  * GPIO19 -> GPIO free
 223  * GPIO20 -> /SDCS2
 224  * GPIO21 -> /CS3 PC card socket select
 225  * GPIO33 -> /CS5  network controller select
 226  * GPIO78 -> /CS2  (16 bit wide data path)
 227  * GPIO80 -> /CS4  (16 bit wide data path)
 228  * GPIO86 -> GPIO free
 229  * GPIO87 -> GPIO free
 230  * GPIO90 -> LED0 on CPU module
 231  * GPIO91 -> LED1 on CPI module
 232  * GPIO117 -> SCL
 233  * GPIO118 -> SDA
 234  */
 235
 236 static unsigned long pcm990_irq_enabled;
 237
 238 static void pcm990_mask_ack_irq(unsigned int irq)
 239 {
 240         int pcm990_irq = (irq - PCM027_IRQ(0));
 241         PCM990_INTMSKENA = (pcm990_irq_enabled &= ~(1 << pcm990_irq));
 242 }
 243
 244 static void pcm990_unmask_irq(unsigned int irq)
 245 {
 246         int pcm990_irq = (irq - PCM027_IRQ(0));
 247         /* the irq can be acknowledged only if deasserted, so it's done here */
 248         PCM990_INTSETCLR |= 1 << pcm990_irq;
 249         PCM990_INTMSKENA  = (pcm990_irq_enabled |= (1 << pcm990_irq));
 250 }
 251
 252 static struct irq_chip pcm990_irq_chip = {
 253         .mask_ack       = pcm990_mask_ack_irq,
 254         .unmask         = pcm990_unmask_irq,
 255 };
 256
 257 static void pcm990_irq_handler(unsigned int irq, struct irq_desc *desc)
 258 {
 259         unsigned long pending = (~PCM990_INTSETCLR) & pcm990_irq_enabled;
 260
 261         do {
 262                 GEDR(PCM990_CTRL_INT_IRQ_GPIO) =
 263                                         GPIO_bit(PCM990_CTRL_INT_IRQ_GPIO);
 264                 if (likely(pending)) {
 265                         irq = PCM027_IRQ(0) + __ffs(pending);
 266                         desc = irq_desc + irq;
 267                         desc_handle_irq(irq, desc);
 268                 }
 269                 pending = (~PCM990_INTSETCLR) & pcm990_irq_enabled;
 270         } while (pending);
 271 }
 272
 273 static void __init pcm990_init_irq(void)
 274 {
 275         int irq;
 276
 277         /* setup extra PCM990 irqs */
 278         for (irq = PCM027_IRQ(0); irq <= PCM027_IRQ(3); irq++) {
 279                 set_irq_chip(irq, &pcm990_irq_chip);
 280                 set_irq_handler(irq, handle_level_irq);
 281                 set_irq_flags(irq, IRQF_VALID | IRQF_PROBE);
 282         }
 283
 284         PCM990_INTMSKENA = 0x00;        /* disable all Interrupts */
 285         PCM990_INTSETCLR = 0xFF;
 286
 287         set_irq_chained_handler(PCM990_CTRL_INT_IRQ, pcm990_irq_handler);
 288         set_irq_type(PCM990_CTRL_INT_IRQ, PCM990_CTRL_INT_IRQ_EDGE);
 289 }
 290
 291 static int pcm990_mci_init(struct device *dev, irq_handler_t mci_detect_int,
 292                         void *data)
 293 {
 294         int err;
 295
 296         err = request_irq(PCM027_MMCDET_IRQ, mci_detect_int, IRQF_DISABLED,
 297                              "MMC card detect", data);
 298         if (err)
 299                 printk(KERN_ERR "pcm990_mci_init: MMC/SD: can't request MMC "
 300                                 "card detect IRQ\n");
 301
 302         return err;
 303 }
 304
 305 static void pcm990_mci_setpower(struct device *dev, unsigned int vdd)
 306 {
 307         struct pxamci_platform_data *p_d = dev->platform_data;
 308
 309         if ((1 << vdd) & p_d->ocr_mask)
 310                 __PCM990_CTRL_REG(PCM990_CTRL_PHYS + PCM990_CTRL_REG5) =
 311                                                 PCM990_CTRL_MMC2PWR;
 312         else
 313                 __PCM990_CTRL_REG(PCM990_CTRL_PHYS + PCM990_CTRL_REG5) =
 314                                                 ~PCM990_CTRL_MMC2PWR;
 315 }
 316
 317 static void pcm990_mci_exit(struct device *dev, void *data)
 318 {
 319         free_irq(PCM027_MMCDET_IRQ, data);
 320 }
 321
 322 #define MSECS_PER_JIFFY (1000/HZ)
 323
 324 static struct pxamci_platform_data pcm990_mci_platform_data = {
 325         .detect_delay   = 250 / MSECS_PER_JIFFY,
 326         .ocr_mask       = MMC_VDD_32_33 | MMC_VDD_33_34,
 327         .init           = pcm990_mci_init,
 328         .setpower       = pcm990_mci_setpower,
 329         .exit           = pcm990_mci_exit,
 330 };
 331
 332 /*
 333  * init OHCI hardware to work with
 334  *
 335  * Note: Only USB port 1 (host only) is connected
 336  *
 337  * GPIO88 (USBHPWR#1): overcurrent in, overcurrent when low
 338  * GPIO89 (USBHPEN#1): power-on out, on when low
 339  */
 340 static int pcm990_ohci_init(struct device *dev)
 341 {
 342         /*
 343          * disable USB port 2 and 3
 344          * power sense is active low
 345          */
 346         UHCHR = ((UHCHR) | UHCHR_PCPL | UHCHR_PSPL | UHCHR_SSEP2 |
 347                                 UHCHR_SSEP3) & ~(UHCHR_SSEP1 | UHCHR_SSE);
 348         /*
 349          * wait 10ms after Power on
 350          * overcurrent per port
 351          * power switch per port
 352          */
 353         UHCRHDA = (5<<24) | (1<<11) | (1<<8);   /* FIXME: Required? */
 354
 355         return 0;
 356 }
 357
 358 static struct pxaohci_platform_data pcm990_ohci_platform_data = {
 359         .port_mode      = PMM_PERPORT_MODE,
 360         .init           = pcm990_ohci_init,
 361         .exit           = NULL,
 362 };
 363
 364 /*
 365  * PXA27x Camera specific stuff
 366  */
 367 #if defined(CONFIG_VIDEO_PXA27x) || defined(CONFIG_VIDEO_PXA27x_MODULE)
 368 static unsigned long pcm990_camera_pin_config[] = {
 369         /* CIF */
 370         GPIO98_CIF_DD_0,
 371         GPIO105_CIF_DD_1,
 372         GPIO104_CIF_DD_2,
 373         GPIO103_CIF_DD_3,
 374         GPIO95_CIF_DD_4,
 375         GPIO94_CIF_DD_5,
 376         GPIO93_CIF_DD_6,
 377         GPIO108_CIF_DD_7,
 378         GPIO107_CIF_DD_8,
 379         GPIO106_CIF_DD_9,
 380         GPIO42_CIF_MCLK,
 381         GPIO45_CIF_PCLK,
 382         GPIO43_CIF_FV,
 383         GPIO44_CIF_LV,
 384 };
 385
 386 static int pcm990_pxacamera_init(struct device *dev)
 387 {
 388         pxa2xx_mfp_config(ARRAY_AND_SIZE(pcm990_camera_pin_config));
 389         return 0;
 390 }
 391
 392 /*
 393  * CICR4: PCLK_EN:      Pixel clock is supplied by the sensor
 394  *      MCLK_EN:        Master clock is generated by PXA
 395  *      PCP:            Data sampled on the falling edge of pixel clock
 396  */
 397 struct pxacamera_platform_data pcm990_pxacamera_platform_data = {
 398         .init   = pcm990_pxacamera_init,
 399         .flags  = PXA_CAMERA_MASTER | PXA_CAMERA_DATAWIDTH_8 | PXA_CAMERA_DATAWIDTH_10 |
 400                 PXA_CAMERA_PCLK_EN | PXA_CAMERA_MCLK_EN/* | PXA_CAMERA_PCP*/,
 401         .mclk_10khz = 1000,
 402 };
 403
 404 #include <linux/i2c/pca953x.h>
 405
 406 static struct pca953x_platform_data pca9536_data = {
 407         .gpio_base      = NR_BUILTIN_GPIO + 1,
 408 };
 409
 410 static struct soc_camera_link iclink[] = {
 411         {
 412                 .bus_id = 0, /* Must match with the camera ID above */
 413                 .gpio   = NR_BUILTIN_GPIO + 1,
 414         }, {
 415                 .bus_id = 0, /* Must match with the camera ID above */
 416         }
 417 };
 418
 419 /* Board I2C devices. */
 420 static struct i2c_board_info __initdata pcm990_i2c_devices[] = {
 421         {
 422                 /* Must initialize before the camera(s) */
 423                 I2C_BOARD_INFO("pca9536", 0x41),
 424                 .platform_data = &pca9536_data,
 425         }, {
 426                 I2C_BOARD_INFO("mt9v022", 0x48),
 427                 .platform_data = &iclink[0], /* With extender */
 428         }, {
 429                 I2C_BOARD_INFO("mt9m001", 0x5d),
 430                 .platform_data = &iclink[0], /* With extender */
 431         },
 432 };
 433 #endif /* CONFIG_VIDEO_PXA27x ||CONFIG_VIDEO_PXA27x_MODULE */
 434
 435 /*
 436  * enable generic access to the base board control CPLDs U6 and U7
 437  */
 438 static struct map_desc pcm990_io_desc[] __initdata = {
 439         {
 440                 .virtual        = PCM990_CTRL_BASE,
 441                 .pfn            = __phys_to_pfn(PCM990_CTRL_PHYS),
 442                 .length         = PCM990_CTRL_SIZE,
 443                 .type           = MT_DEVICE     /* CPLD */
 444         }, {
 445                 .virtual        = PCM990_CF_PLD_BASE,
 446                 .pfn            = __phys_to_pfn(PCM990_CF_PLD_PHYS),
 447                 .length         = PCM990_CF_PLD_SIZE,
 448                 .type           = MT_DEVICE     /* CPLD */
 449         }
 450 };
 451
 452 /*
 453  * system init for baseboard usage. Will be called by pcm027 init.
 454  *
 455  * Add platform devices present on this baseboard and init
 456  * them from CPU side as far as required to use them later on
 457  */
 458 void __init pcm990_baseboard_init(void)
 459 {
 460         pxa2xx_mfp_config(ARRAY_AND_SIZE(pcm990_pin_config));
 461
 462         /* register CPLD access */
 463         iotable_init(ARRAY_AND_SIZE(pcm990_io_desc));
 464
 465         /* register CPLD's IRQ controller */
 466         pcm990_init_irq();
 467
 468 #ifndef CONFIG_PCM990_DISPLAY_NONE
 469         set_pxa_fb_info(&pcm990_fbinfo);
 470 #endif
 471         platform_device_register(&pcm990_backlight_device);
 472
 473         /* MMC */
 474         pxa_set_mci_info(&pcm990_mci_platform_data);
 475
 476         /* USB host */
 477         pxa_set_ohci_info(&pcm990_ohci_platform_data);
 478
 479         pxa_set_i2c_info(NULL);
 480         pxa_set_ac97_info(NULL);
 481
 482 #if defined(CONFIG_VIDEO_PXA27x) || defined(CONFIG_VIDEO_PXA27x_MODULE)
 483         pxa_set_camera_info(&pcm990_pxacamera_platform_data);
 484
 485         i2c_register_board_info(0, ARRAY_AND_SIZE(pcm990_i2c_devices));
 486 #endif
 487
 488         printk(KERN_INFO "PCM-990 Evaluation baseboard initialized\n");
 489 }