git.oblomov.eu Git - linux-2.6/blob - drivers/char/synclink_gt.c

   1 /*
   2  * $Id: synclink_gt.c,v 4.36 2006/08/28 20:47:14 paulkf Exp $
   3  *
   4  * Device driver for Microgate SyncLink GT serial adapters.
   5  *
   6  * written by Paul Fulghum for Microgate Corporation
   7  * paulkf@microgate.com
   8  *
   9  * Microgate and SyncLink are trademarks of Microgate Corporation
  10  *
  11  * This code is released under the GNU General Public License (GPL)
  12  *
  13  * THIS SOFTWARE IS PROVIDED ``AS IS'' AND ANY EXPRESS OR IMPLIED
  14  * WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES
  15  * OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
  16  * DISCLAIMED.  IN NO EVENT SHALL THE AUTHOR BE LIABLE FOR ANY DIRECT,
  17  * INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
  18  * (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR
  19  * SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION)
  20  * HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT,
  21  * STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE)
  22  * ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED
  23  * OF THE POSSIBILITY OF SUCH DAMAGE.
  24  */
  25
  26 /*
  27  * DEBUG OUTPUT DEFINITIONS
  28  *
  29  * uncomment lines below to enable specific types of debug output
  30  *
  31  * DBGINFO   information - most verbose output
  32  * DBGERR    serious errors
  33  * DBGBH     bottom half service routine debugging
  34  * DBGISR    interrupt service routine debugging
  35  * DBGDATA   output receive and transmit data
  36  * DBGTBUF   output transmit DMA buffers and registers
  37  * DBGRBUF   output receive DMA buffers and registers
  38  */
  39
  40 #define DBGINFO(fmt) if (debug_level >= DEBUG_LEVEL_INFO) printk fmt
  41 #define DBGERR(fmt) if (debug_level >= DEBUG_LEVEL_ERROR) printk fmt
  42 #define DBGBH(fmt) if (debug_level >= DEBUG_LEVEL_BH) printk fmt
  43 #define DBGISR(fmt) if (debug_level >= DEBUG_LEVEL_ISR) printk fmt
  44 #define DBGDATA(info, buf, size, label) if (debug_level >= DEBUG_LEVEL_DATA) trace_block((info), (buf), (size), (label))
  45 //#define DBGTBUF(info) dump_tbufs(info)
  46 //#define DBGRBUF(info) dump_rbufs(info)
  47
  48
  49 #include <linux/module.h>
  50 #include <linux/version.h>
  51 #include <linux/errno.h>
  52 #include <linux/signal.h>
  53 #include <linux/sched.h>
  54 #include <linux/timer.h>
  55 #include <linux/interrupt.h>
  56 #include <linux/pci.h>
  57 #include <linux/tty.h>
  58 #include <linux/tty_flip.h>
  59 #include <linux/serial.h>
  60 #include <linux/major.h>
  61 #include <linux/string.h>
  62 #include <linux/fcntl.h>
  63 #include <linux/ptrace.h>
  64 #include <linux/ioport.h>
  65 #include <linux/mm.h>
  66 #include <linux/slab.h>
  67 #include <linux/netdevice.h>
  68 #include <linux/vmalloc.h>
  69 #include <linux/init.h>
  70 #include <linux/delay.h>
  71 #include <linux/ioctl.h>
  72 #include <linux/termios.h>
  73 #include <linux/bitops.h>
  74 #include <linux/workqueue.h>
  75 #include <linux/hdlc.h>
  76
  77 #include <asm/system.h>
  78 #include <asm/io.h>
  79 #include <asm/irq.h>
  80 #include <asm/dma.h>
  81 #include <asm/types.h>
  82 #include <asm/uaccess.h>
  83
  84 #include "linux/synclink.h"
  85
  86 #if defined(CONFIG_HDLC) || (defined(CONFIG_HDLC_MODULE) && defined(CONFIG_SYNCLINK_GT_MODULE))
  87 #define SYNCLINK_GENERIC_HDLC 1
  88 #else
  89 #define SYNCLINK_GENERIC_HDLC 0
  90 #endif
  91
  92 /*
  93  * module identification
  94  */
  95 static char *driver_name     = "SyncLink GT";
  96 static char *driver_version  = "$Revision: 4.36 $";
  97 static char *tty_driver_name = "synclink_gt";
  98 static char *tty_dev_prefix  = "ttySLG";
  99 MODULE_LICENSE("GPL");
 100 #define MGSL_MAGIC 0x5401
 101 #define MAX_DEVICES 32
 102
 103 static struct pci_device_id pci_table[] = {
 104         {PCI_VENDOR_ID_MICROGATE, SYNCLINK_GT_DEVICE_ID, PCI_ANY_ID, PCI_ANY_ID,},
 105         {PCI_VENDOR_ID_MICROGATE, SYNCLINK_GT2_DEVICE_ID, PCI_ANY_ID, PCI_ANY_ID,},
 106         {PCI_VENDOR_ID_MICROGATE, SYNCLINK_GT4_DEVICE_ID, PCI_ANY_ID, PCI_ANY_ID,},
 107         {PCI_VENDOR_ID_MICROGATE, SYNCLINK_AC_DEVICE_ID, PCI_ANY_ID, PCI_ANY_ID,},
 108         {0,}, /* terminate list */
 109 };
 110 MODULE_DEVICE_TABLE(pci, pci_table);
 111
 112 static int  init_one(struct pci_dev *dev,const struct pci_device_id *ent);
 113 static void remove_one(struct pci_dev *dev);
 114 static struct pci_driver pci_driver = {
 115         .name           = "synclink_gt",
 116         .id_table       = pci_table,
 117         .probe          = init_one,
 118         .remove         = __devexit_p(remove_one),
 119 };
 120
 121 static int pci_registered;
 122
 123 /*
 124  * module configuration and status
 125  */
 126 static struct slgt_info *slgt_device_list;
 127 static int slgt_device_count;
 128
 129 static int ttymajor;
 130 static int debug_level;
 131 static int maxframe[MAX_DEVICES];
 132 static int dosyncppp[MAX_DEVICES];
 133
 134 module_param(ttymajor, int, 0);
 135 module_param(debug_level, int, 0);
 136 module_param_array(maxframe, int, NULL, 0);
 137 module_param_array(dosyncppp, int, NULL, 0);
 138
 139 MODULE_PARM_DESC(ttymajor, "TTY major device number override: 0=auto assigned");
 140 MODULE_PARM_DESC(debug_level, "Debug syslog output: 0=disabled, 1 to 5=increasing detail");
 141 MODULE_PARM_DESC(maxframe, "Maximum frame size used by device (4096 to 65535)");
 142 MODULE_PARM_DESC(dosyncppp, "Enable synchronous net device, 0=disable 1=enable");
 143
 144 /*
 145  * tty support and callbacks
 146  */
 147 #define RELEVANT_IFLAG(iflag) (iflag & (IGNBRK|BRKINT|IGNPAR|PARMRK|INPCK))
 148
 149 static struct tty_driver *serial_driver;
 150
 151 static int  open(struct tty_struct *tty, struct file * filp);
 152 static void close(struct tty_struct *tty, struct file * filp);
 153 static void hangup(struct tty_struct *tty);
 154 static void set_termios(struct tty_struct *tty, struct ktermios *old_termios);
 155
 156 static int  write(struct tty_struct *tty, const unsigned char *buf, int count);
 157 static void put_char(struct tty_struct *tty, unsigned char ch);
 158 static void send_xchar(struct tty_struct *tty, char ch);
 159 static void wait_until_sent(struct tty_struct *tty, int timeout);
 160 static int  write_room(struct tty_struct *tty);
 161 static void flush_chars(struct tty_struct *tty);
 162 static void flush_buffer(struct tty_struct *tty);
 163 static void tx_hold(struct tty_struct *tty);
 164 static void tx_release(struct tty_struct *tty);
 165
 166 static int  ioctl(struct tty_struct *tty, struct file *file, unsigned int cmd, unsigned long arg);
 167 static int  read_proc(char *page, char **start, off_t off, int count,int *eof, void *data);
 168 static int  chars_in_buffer(struct tty_struct *tty);
 169 static void throttle(struct tty_struct * tty);
 170 static void unthrottle(struct tty_struct * tty);
 171 static void set_break(struct tty_struct *tty, int break_state);
 172
 173 /*
 174  * generic HDLC support and callbacks
 175  */
 176 #if SYNCLINK_GENERIC_HDLC
 177 #define dev_to_port(D) (dev_to_hdlc(D)->priv)
 178 static void hdlcdev_tx_done(struct slgt_info *info);
 179 static void hdlcdev_rx(struct slgt_info *info, char *buf, int size);
 180 static int  hdlcdev_init(struct slgt_info *info);
 181 static void hdlcdev_exit(struct slgt_info *info);
 182 #endif
 183
 184
 185 /*
 186  * device specific structures, macros and functions
 187  */
 188
 189 #define SLGT_MAX_PORTS 4
 190 #define SLGT_REG_SIZE  256
 191
 192 /*
 193  * conditional wait facility
 194  */
 195 struct cond_wait {
 196         struct cond_wait *next;
 197         wait_queue_head_t q;
 198         wait_queue_t wait;
 199         unsigned int data;
 200 };
 201 static void init_cond_wait(struct cond_wait *w, unsigned int data);
 202 static void add_cond_wait(struct cond_wait **head, struct cond_wait *w);
 203 static void remove_cond_wait(struct cond_wait **head, struct cond_wait *w);
 204 static void flush_cond_wait(struct cond_wait **head);
 205
 206 /*
 207  * DMA buffer descriptor and access macros
 208  */
 209 struct slgt_desc
 210 {
 211         unsigned short count;
 212         unsigned short status;
 213         unsigned int pbuf;  /* physical address of data buffer */
 214         unsigned int next;  /* physical address of next descriptor */
 215
 216         /* driver book keeping */
 217         char *buf;          /* virtual  address of data buffer */
 218         unsigned int pdesc; /* physical address of this descriptor */
 219         dma_addr_t buf_dma_addr;
 220 };
 221
 222 #define set_desc_buffer(a,b) (a).pbuf = cpu_to_le32((unsigned int)(b))
 223 #define set_desc_next(a,b) (a).next   = cpu_to_le32((unsigned int)(b))
 224 #define set_desc_count(a,b)(a).count  = cpu_to_le16((unsigned short)(b))
 225 #define set_desc_eof(a,b)  (a).status = cpu_to_le16((b) ? (le16_to_cpu((a).status) | BIT0) : (le16_to_cpu((a).status) & ~BIT0))
 226 #define desc_count(a)      (le16_to_cpu((a).count))
 227 #define desc_status(a)     (le16_to_cpu((a).status))
 228 #define desc_complete(a)   (le16_to_cpu((a).status) & BIT15)
 229 #define desc_eof(a)        (le16_to_cpu((a).status) & BIT2)
 230 #define desc_crc_error(a)  (le16_to_cpu((a).status) & BIT1)
 231 #define desc_abort(a)      (le16_to_cpu((a).status) & BIT0)
 232 #define desc_residue(a)    ((le16_to_cpu((a).status) & 0x38) >> 3)
 233
 234 struct _input_signal_events {
 235         int ri_up;
 236         int ri_down;
 237         int dsr_up;
 238         int dsr_down;
 239         int dcd_up;
 240         int dcd_down;
 241         int cts_up;
 242         int cts_down;
 243 };
 244
 245 /*
 246  * device instance data structure
 247  */
 248 struct slgt_info {
 249         void *if_ptr;           /* General purpose pointer (used by SPPP) */
 250
 251         struct slgt_info *next_device;  /* device list link */
 252
 253         int magic;
 254         int flags;
 255
 256         char device_name[25];
 257         struct pci_dev *pdev;
 258
 259         int port_count;  /* count of ports on adapter */
 260         int adapter_num; /* adapter instance number */
 261         int port_num;    /* port instance number */
 262
 263         /* array of pointers to port contexts on this adapter */
 264         struct slgt_info *port_array[SLGT_MAX_PORTS];
 265
 266         int                     count;          /* count of opens */
 267         int                     line;           /* tty line instance number */
 268         unsigned short          close_delay;
 269         unsigned short          closing_wait;   /* time to wait before closing */
 270
 271         struct mgsl_icount      icount;
 272
 273         struct tty_struct       *tty;
 274         int                     timeout;
 275         int                     x_char;         /* xon/xoff character */
 276         int                     blocked_open;   /* # of blocked opens */
 277         unsigned int            read_status_mask;
 278         unsigned int            ignore_status_mask;
 279
 280         wait_queue_head_t       open_wait;
 281         wait_queue_head_t       close_wait;
 282
 283         wait_queue_head_t       status_event_wait_q;
 284         wait_queue_head_t       event_wait_q;
 285         struct timer_list       tx_timer;
 286         struct timer_list       rx_timer;
 287
 288         unsigned int            gpio_present;
 289         struct cond_wait        *gpio_wait_q;
 290
 291         spinlock_t lock;        /* spinlock for synchronizing with ISR */
 292
 293         struct work_struct task;
 294         u32 pending_bh;
 295         int bh_requested;
 296         int bh_running;
 297
 298         int isr_overflow;
 299         int irq_requested;      /* nonzero if IRQ requested */
 300         int irq_occurred;       /* for diagnostics use */
 301
 302         /* device configuration */
 303
 304         unsigned int bus_type;
 305         unsigned int irq_level;
 306         unsigned long irq_flags;
 307
 308         unsigned char __iomem * reg_addr;  /* memory mapped registers address */
 309         u32 phys_reg_addr;
 310         int reg_addr_requested;
 311
 312         MGSL_PARAMS params;       /* communications parameters */
 313         u32 idle_mode;
 314         u32 max_frame_size;       /* as set by device config */
 315
 316         unsigned int raw_rx_size;
 317         unsigned int if_mode;
 318
 319         /* device status */
 320
 321         int rx_enabled;
 322         int rx_restart;
 323
 324         int tx_enabled;
 325         int tx_active;
 326
 327         unsigned char signals;    /* serial signal states */
 328         int init_error;  /* initialization error */
 329
 330         unsigned char *tx_buf;
 331         int tx_count;
 332
 333         char flag_buf[MAX_ASYNC_BUFFER_SIZE];
 334         char char_buf[MAX_ASYNC_BUFFER_SIZE];
 335         BOOLEAN drop_rts_on_tx_done;
 336         struct  _input_signal_events    input_signal_events;
 337
 338         int dcd_chkcount;       /* check counts to prevent */
 339         int cts_chkcount;       /* too many IRQs if a signal */
 340         int dsr_chkcount;       /* is floating */
 341         int ri_chkcount;
 342
 343         char *bufs;             /* virtual address of DMA buffer lists */
 344         dma_addr_t bufs_dma_addr; /* physical address of buffer descriptors */
 345
 346         unsigned int rbuf_count;
 347         struct slgt_desc *rbufs;
 348         unsigned int rbuf_current;
 349         unsigned int rbuf_index;
 350
 351         unsigned int tbuf_count;
 352         struct slgt_desc *tbufs;
 353         unsigned int tbuf_current;
 354         unsigned int tbuf_start;
 355
 356         unsigned char *tmp_rbuf;
 357         unsigned int tmp_rbuf_count;
 358
 359         /* SPPP/Cisco HDLC device parts */
 360
 361         int netcount;
 362         int dosyncppp;
 363         spinlock_t netlock;
 364 #if SYNCLINK_GENERIC_HDLC
 365         struct net_device *netdev;
 366 #endif
 367
 368 };
 369
 370 static MGSL_PARAMS default_params = {
 371         .mode            = MGSL_MODE_HDLC,
 372         .loopback        = 0,
 373         .flags           = HDLC_FLAG_UNDERRUN_ABORT15,
 374         .encoding        = HDLC_ENCODING_NRZI_SPACE,
 375         .clock_speed     = 0,
 376         .addr_filter     = 0xff,
 377         .crc_type        = HDLC_CRC_16_CCITT,
 378         .preamble_length = HDLC_PREAMBLE_LENGTH_8BITS,
 379         .preamble        = HDLC_PREAMBLE_PATTERN_NONE,
 380         .data_rate       = 9600,
 381         .data_bits       = 8,
 382         .stop_bits       = 1,
 383         .parity          = ASYNC_PARITY_NONE
 384 };
 385
 386
 387 #define BH_RECEIVE  1
 388 #define BH_TRANSMIT 2
 389 #define BH_STATUS   4
 390 #define IO_PIN_SHUTDOWN_LIMIT 100
 391
 392 #define DMABUFSIZE 256
 393 #define DESC_LIST_SIZE 4096
 394
 395 #define MASK_PARITY  BIT1
 396 #define MASK_FRAMING BIT0
 397 #define MASK_BREAK   BIT14
 398 #define MASK_OVERRUN BIT4
 399
 400 #define GSR   0x00 /* global status */
 401 #define JCR   0x04 /* JTAG control */
 402 #define IODR  0x08 /* GPIO direction */
 403 #define IOER  0x0c /* GPIO interrupt enable */
 404 #define IOVR  0x10 /* GPIO value */
 405 #define IOSR  0x14 /* GPIO interrupt status */
 406 #define TDR   0x80 /* tx data */
 407 #define RDR   0x80 /* rx data */
 408 #define TCR   0x82 /* tx control */
 409 #define TIR   0x84 /* tx idle */
 410 #define TPR   0x85 /* tx preamble */
 411 #define RCR   0x86 /* rx control */
 412 #define VCR   0x88 /* V.24 control */
 413 #define CCR   0x89 /* clock control */
 414 #define BDR   0x8a /* baud divisor */
 415 #define SCR   0x8c /* serial control */
 416 #define SSR   0x8e /* serial status */
 417 #define RDCSR 0x90 /* rx DMA control/status */
 418 #define TDCSR 0x94 /* tx DMA control/status */
 419 #define RDDAR 0x98 /* rx DMA descriptor address */
 420 #define TDDAR 0x9c /* tx DMA descriptor address */
 421
 422 #define RXIDLE      BIT14
 423 #define RXBREAK     BIT14
 424 #define IRQ_TXDATA  BIT13
 425 #define IRQ_TXIDLE  BIT12
 426 #define IRQ_TXUNDER BIT11 /* HDLC */
 427 #define IRQ_RXDATA  BIT10
 428 #define IRQ_RXIDLE  BIT9  /* HDLC */
 429 #define IRQ_RXBREAK BIT9  /* async */
 430 #define IRQ_RXOVER  BIT8
 431 #define IRQ_DSR     BIT7
 432 #define IRQ_CTS     BIT6
 433 #define IRQ_DCD     BIT5
 434 #define IRQ_RI      BIT4
 435 #define IRQ_ALL     0x3ff0
 436 #define IRQ_MASTER  BIT0
 437
 438 #define slgt_irq_on(info, mask) \
 439         wr_reg16((info), SCR, (unsigned short)(rd_reg16((info), SCR) | (mask)))
 440 #define slgt_irq_off(info, mask) \
 441         wr_reg16((info), SCR, (unsigned short)(rd_reg16((info), SCR) & ~(mask)))
 442
 443 static __u8  rd_reg8(struct slgt_info *info, unsigned int addr);
 444 static void  wr_reg8(struct slgt_info *info, unsigned int addr, __u8 value);
 445 static __u16 rd_reg16(struct slgt_info *info, unsigned int addr);
 446 static void  wr_reg16(struct slgt_info *info, unsigned int addr, __u16 value);
 447 static __u32 rd_reg32(struct slgt_info *info, unsigned int addr);
 448 static void  wr_reg32(struct slgt_info *info, unsigned int addr, __u32 value);
 449
 450 static void  msc_set_vcr(struct slgt_info *info);
 451
 452 static int  startup(struct slgt_info *info);
 453 static int  block_til_ready(struct tty_struct *tty, struct file * filp,struct slgt_info *info);
 454 static void shutdown(struct slgt_info *info);
 455 static void program_hw(struct slgt_info *info);
 456 static void change_params(struct slgt_info *info);
 457
 458 static int  register_test(struct slgt_info *info);
 459 static int  irq_test(struct slgt_info *info);
 460 static int  loopback_test(struct slgt_info *info);
 461 static int  adapter_test(struct slgt_info *info);
 462
 463 static void reset_adapter(struct slgt_info *info);
 464 static void reset_port(struct slgt_info *info);
 465 static void async_mode(struct slgt_info *info);
 466 static void sync_mode(struct slgt_info *info);
 467
 468 static void rx_stop(struct slgt_info *info);
 469 static void rx_start(struct slgt_info *info);
 470 static void reset_rbufs(struct slgt_info *info);
 471 static void free_rbufs(struct slgt_info *info, unsigned int first, unsigned int last);
 472 static void rdma_reset(struct slgt_info *info);
 473 static int  rx_get_frame(struct slgt_info *info);
 474 static int  rx_get_buf(struct slgt_info *info);
 475
 476 static void tx_start(struct slgt_info *info);
 477 static void tx_stop(struct slgt_info *info);
 478 static void tx_set_idle(struct slgt_info *info);
 479 static unsigned int free_tbuf_count(struct slgt_info *info);
 480 static void reset_tbufs(struct slgt_info *info);
 481 static void tdma_reset(struct slgt_info *info);
 482 static void tx_load(struct slgt_info *info, const char *buf, unsigned int count);
 483
 484 static void get_signals(struct slgt_info *info);
 485 static void set_signals(struct slgt_info *info);
 486 static void enable_loopback(struct slgt_info *info);
 487 static void set_rate(struct slgt_info *info, u32 data_rate);
 488
 489 static int  bh_action(struct slgt_info *info);
 490 static void bh_handler(struct work_struct *work);
 491 static void bh_transmit(struct slgt_info *info);
 492 static void isr_serial(struct slgt_info *info);
 493 static void isr_rdma(struct slgt_info *info);
 494 static void isr_txeom(struct slgt_info *info, unsigned short status);
 495 static void isr_tdma(struct slgt_info *info);
 496 static irqreturn_t slgt_interrupt(int irq, void *dev_id);
 497
 498 static int  alloc_dma_bufs(struct slgt_info *info);
 499 static void free_dma_bufs(struct slgt_info *info);
 500 static int  alloc_desc(struct slgt_info *info);
 501 static void free_desc(struct slgt_info *info);
 502 static int  alloc_bufs(struct slgt_info *info, struct slgt_desc *bufs, int count);
 503 static void free_bufs(struct slgt_info *info, struct slgt_desc *bufs, int count);
 504
 505 static int  alloc_tmp_rbuf(struct slgt_info *info);
 506 static void free_tmp_rbuf(struct slgt_info *info);
 507
 508 static void tx_timeout(unsigned long context);
 509 static void rx_timeout(unsigned long context);
 510
 511 /*
 512  * ioctl handlers
 513  */
 514 static int  get_stats(struct slgt_info *info, struct mgsl_icount __user *user_icount);
 515 static int  get_params(struct slgt_info *info, MGSL_PARAMS __user *params);
 516 static int  set_params(struct slgt_info *info, MGSL_PARAMS __user *params);
 517 static int  get_txidle(struct slgt_info *info, int __user *idle_mode);
 518 static int  set_txidle(struct slgt_info *info, int idle_mode);
 519 static int  tx_enable(struct slgt_info *info, int enable);
 520 static int  tx_abort(struct slgt_info *info);
 521 static int  rx_enable(struct slgt_info *info, int enable);
 522 static int  modem_input_wait(struct slgt_info *info,int arg);
 523 static int  wait_mgsl_event(struct slgt_info *info, int __user *mask_ptr);
 524 static int  tiocmget(struct tty_struct *tty, struct file *file);
 525 static int  tiocmset(struct tty_struct *tty, struct file *file,
 526                      unsigned int set, unsigned int clear);
 527 static void set_break(struct tty_struct *tty, int break_state);
 528 static int  get_interface(struct slgt_info *info, int __user *if_mode);
 529 static int  set_interface(struct slgt_info *info, int if_mode);
 530 static int  set_gpio(struct slgt_info *info, struct gpio_desc __user *gpio);
 531 static int  get_gpio(struct slgt_info *info, struct gpio_desc __user *gpio);
 532 static int  wait_gpio(struct slgt_info *info, struct gpio_desc __user *gpio);
 533
 534 /*
 535  * driver functions
 536  */
 537 static void add_device(struct slgt_info *info);
 538 static void device_init(int adapter_num, struct pci_dev *pdev);
 539 static int  claim_resources(struct slgt_info *info);
 540 static void release_resources(struct slgt_info *info);
 541
 542 /*
 543  * DEBUG OUTPUT CODE
 544  */
 545 #ifndef DBGINFO
 546 #define DBGINFO(fmt)
 547 #endif
 548 #ifndef DBGERR
 549 #define DBGERR(fmt)
 550 #endif
 551 #ifndef DBGBH
 552 #define DBGBH(fmt)
 553 #endif
 554 #ifndef DBGISR
 555 #define DBGISR(fmt)
 556 #endif
 557
 558 #ifdef DBGDATA
 559 static void trace_block(struct slgt_info *info, const char *data, int count, const char *label)
 560 {
 561         int i;
 562         int linecount;
 563         printk("%s %s data:\n",info->device_name, label);
 564         while(count) {
 565                 linecount = (count > 16) ? 16 : count;
 566                 for(i=0; i < linecount; i++)
 567                         printk("%02X ",(unsigned char)data[i]);
 568                 for(;i<17;i++)
 569                         printk("   ");
 570                 for(i=0;i<linecount;i++) {
 571                         if (data[i]>=040 && data[i]<=0176)
 572                                 printk("%c",data[i]);
 573                         else
 574                                 printk(".");
 575                 }
 576                 printk("\n");
 577                 data  += linecount;
 578                 count -= linecount;
 579         }
 580 }
 581 #else
 582 #define DBGDATA(info, buf, size, label)
 583 #endif
 584
 585 #ifdef DBGTBUF
 586 static void dump_tbufs(struct slgt_info *info)
 587 {
 588         int i;
 589         printk("tbuf_current=%d\n", info->tbuf_current);
 590         for (i=0 ; i < info->tbuf_count ; i++) {
 591                 printk("%d: count=%04X status=%04X\n",
 592                         i, le16_to_cpu(info->tbufs[i].count), le16_to_cpu(info->tbufs[i].status));
 593         }
 594 }
 595 #else
 596 #define DBGTBUF(info)
 597 #endif
 598
 599 #ifdef DBGRBUF
 600 static void dump_rbufs(struct slgt_info *info)
 601 {
 602         int i;
 603         printk("rbuf_current=%d\n", info->rbuf_current);
 604         for (i=0 ; i < info->rbuf_count ; i++) {
 605                 printk("%d: count=%04X status=%04X\n",
 606                         i, le16_to_cpu(info->rbufs[i].count), le16_to_cpu(info->rbufs[i].status));
 607         }
 608 }
 609 #else
 610 #define DBGRBUF(info)
 611 #endif
 612
 613 static inline int sanity_check(struct slgt_info *info, char *devname, const char *name)
 614 {
 615 #ifdef SANITY_CHECK
 616         if (!info) {
 617                 printk("null struct slgt_info for (%s) in %s\n", devname, name);
 618                 return 1;
 619         }
 620         if (info->magic != MGSL_MAGIC) {
 621                 printk("bad magic number struct slgt_info (%s) in %s\n", devname, name);
 622                 return 1;
 623         }
 624 #else
 625         if (!info)
 626                 return 1;
 627 #endif
 628         return 0;
 629 }
 630
 631 /**
 632  * line discipline callback wrappers
 633  *
 634  * The wrappers maintain line discipline references
 635  * while calling into the line discipline.
 636  *
 637  * ldisc_receive_buf  - pass receive data to line discipline
 638  */
 639 static void ldisc_receive_buf(struct tty_struct *tty,
 640                               const __u8 *data, char *flags, int count)
 641 {
 642         struct tty_ldisc *ld;
 643         if (!tty)
 644                 return;
 645         ld = tty_ldisc_ref(tty);
 646         if (ld) {
 647                 if (ld->receive_buf)
 648                         ld->receive_buf(tty, data, flags, count);
 649                 tty_ldisc_deref(ld);
 650         }
 651 }
 652
 653 /* tty callbacks */
 654
 655 static int open(struct tty_struct *tty, struct file *filp)
 656 {
 657         struct slgt_info *info;
 658         int retval, line;
 659         unsigned long flags;
 660
 661         line = tty->index;
 662         if ((line < 0) || (line >= slgt_device_count)) {
 663                 DBGERR(("%s: open with invalid line #%d.\n", driver_name, line));
 664                 return -ENODEV;
 665         }
 666
 667         info = slgt_device_list;
 668         while(info && info->line != line)
 669                 info = info->next_device;
 670         if (sanity_check(info, tty->name, "open"))
 671                 return -ENODEV;
 672         if (info->init_error) {
 673                 DBGERR(("%s init error=%d\n", info->device_name, info->init_error));
 674                 return -ENODEV;
 675         }
 676
 677         tty->driver_data = info;
 678         info->tty = tty;
 679
 680         DBGINFO(("%s open, old ref count = %d\n", info->device_name, info->count));
 681
 682         /* If port is closing, signal caller to try again */
 683         if (tty_hung_up_p(filp) || info->flags & ASYNC_CLOSING){
 684                 if (info->flags & ASYNC_CLOSING)
 685                         interruptible_sleep_on(&info->close_wait);
 686                 retval = ((info->flags & ASYNC_HUP_NOTIFY) ?
 687                         -EAGAIN : -ERESTARTSYS);
 688                 goto cleanup;
 689         }
 690
 691         info->tty->low_latency = (info->flags & ASYNC_LOW_LATENCY) ? 1 : 0;
 692
 693         spin_lock_irqsave(&info->netlock, flags);
 694         if (info->netcount) {
 695                 retval = -EBUSY;
 696                 spin_unlock_irqrestore(&info->netlock, flags);
 697                 goto cleanup;
 698         }
 699         info->count++;
 700         spin_unlock_irqrestore(&info->netlock, flags);
 701
 702         if (info->count == 1) {
 703                 /* 1st open on this device, init hardware */
 704                 retval = startup(info);
 705                 if (retval < 0)
 706                         goto cleanup;
 707         }
 708
 709         retval = block_til_ready(tty, filp, info);
 710         if (retval) {
 711                 DBGINFO(("%s block_til_ready rc=%d\n", info->device_name, retval));
 712                 goto cleanup;
 713         }
 714
 715         retval = 0;
 716
 717 cleanup:
 718         if (retval) {
 719                 if (tty->count == 1)
 720                         info->tty = NULL; /* tty layer will release tty struct */
 721                 if(info->count)
 722                         info->count--;
 723         }
 724
 725         DBGINFO(("%s open rc=%d\n", info->device_name, retval));
 726         return retval;
 727 }
 728
 729 static void close(struct tty_struct *tty, struct file *filp)
 730 {
 731         struct slgt_info *info = tty->driver_data;
 732
 733         if (sanity_check(info, tty->name, "close"))
 734                 return;
 735         DBGINFO(("%s close entry, count=%d\n", info->device_name, info->count));
 736
 737         if (!info->count)
 738                 return;
 739
 740         if (tty_hung_up_p(filp))
 741                 goto cleanup;
 742
 743         if ((tty->count == 1) && (info->count != 1)) {
 744                 /*
 745                  * tty->count is 1 and the tty structure will be freed.
 746                  * info->count should be one in this case.
 747                  * if it's not, correct it so that the port is shutdown.
 748                  */
 749                 DBGERR(("%s close: bad refcount; tty->count=1, "
 750                        "info->count=%d\n", info->device_name, info->count));
 751                 info->count = 1;
 752         }
 753
 754         info->count--;
 755
 756         /* if at least one open remaining, leave hardware active */
 757         if (info->count)
 758                 goto cleanup;
 759
 760         info->flags |= ASYNC_CLOSING;
 761
 762         /* set tty->closing to notify line discipline to
 763          * only process XON/XOFF characters. Only the N_TTY
 764          * discipline appears to use this (ppp does not).
 765          */
 766         tty->closing = 1;
 767
 768         /* wait for transmit data to clear all layers */
 769
 770         if (info->closing_wait != ASYNC_CLOSING_WAIT_NONE) {
 771                 DBGINFO(("%s call tty_wait_until_sent\n", info->device_name));
 772                 tty_wait_until_sent(tty, info->closing_wait);
 773         }
 774
 775         if (info->flags & ASYNC_INITIALIZED)
 776                 wait_until_sent(tty, info->timeout);
 777         if (tty->driver->flush_buffer)
 778                 tty->driver->flush_buffer(tty);
 779         tty_ldisc_flush(tty);
 780
 781         shutdown(info);
 782
 783         tty->closing = 0;
 784         info->tty = NULL;
 785
 786         if (info->blocked_open) {
 787                 if (info->close_delay) {
 788                         msleep_interruptible(jiffies_to_msecs(info->close_delay));
 789                 }
 790                 wake_up_interruptible(&info->open_wait);
 791         }
 792
 793         info->flags &= ~(ASYNC_NORMAL_ACTIVE|ASYNC_CLOSING);
 794
 795         wake_up_interruptible(&info->close_wait);
 796
 797 cleanup:
 798         DBGINFO(("%s close exit, count=%d\n", tty->driver->name, info->count));
 799 }
 800
 801 static void hangup(struct tty_struct *tty)
 802 {
 803         struct slgt_info *info = tty->driver_data;
 804
 805         if (sanity_check(info, tty->name, "hangup"))
 806                 return;
 807         DBGINFO(("%s hangup\n", info->device_name));
 808
 809         flush_buffer(tty);
 810         shutdown(info);
 811
 812         info->count = 0;
 813         info->flags &= ~ASYNC_NORMAL_ACTIVE;
 814         info->tty = NULL;
 815
 816         wake_up_interruptible(&info->open_wait);
 817 }
 818
 819 static void set_termios(struct tty_struct *tty, struct ktermios *old_termios)
 820 {
 821         struct slgt_info *info = tty->driver_data;
 822         unsigned long flags;
 823
 824         DBGINFO(("%s set_termios\n", tty->driver->name));
 825
 826         /* just return if nothing has changed */
 827         if ((tty->termios->c_cflag == old_termios->c_cflag)
 828             && (RELEVANT_IFLAG(tty->termios->c_iflag)
 829                 == RELEVANT_IFLAG(old_termios->c_iflag)))
 830                 return;
 831
 832         change_params(info);
 833
 834         /* Handle transition to B0 status */
 835         if (old_termios->c_cflag & CBAUD &&
 836             !(tty->termios->c_cflag & CBAUD)) {
 837                 info->signals &= ~(SerialSignal_RTS + SerialSignal_DTR);
 838                 spin_lock_irqsave(&info->lock,flags);
 839                 set_signals(info);
 840                 spin_unlock_irqrestore(&info->lock,flags);
 841         }
 842
 843         /* Handle transition away from B0 status */
 844         if (!(old_termios->c_cflag & CBAUD) &&
 845             tty->termios->c_cflag & CBAUD) {
 846                 info->signals |= SerialSignal_DTR;
 847                 if (!(tty->termios->c_cflag & CRTSCTS) ||
 848                     !test_bit(TTY_THROTTLED, &tty->flags)) {
 849                         info->signals |= SerialSignal_RTS;
 850                 }
 851                 spin_lock_irqsave(&info->lock,flags);
 852                 set_signals(info);
 853                 spin_unlock_irqrestore(&info->lock,flags);
 854         }
 855
 856         /* Handle turning off CRTSCTS */
 857         if (old_termios->c_cflag & CRTSCTS &&
 858             !(tty->termios->c_cflag & CRTSCTS)) {
 859                 tty->hw_stopped = 0;
 860                 tx_release(tty);
 861         }
 862 }
 863
 864 static int write(struct tty_struct *tty,
 865                  const unsigned char *buf, int count)
 866 {
 867         int ret = 0;
 868         struct slgt_info *info = tty->driver_data;
 869         unsigned long flags;
 870
 871         if (sanity_check(info, tty->name, "write"))
 872                 goto cleanup;
 873         DBGINFO(("%s write count=%d\n", info->device_name, count));
 874
 875         if (!info->tx_buf)
 876                 goto cleanup;
 877
 878         if (count > info->max_frame_size) {
 879                 ret = -EIO;
 880                 goto cleanup;
 881         }
 882
 883         if (!count)
 884                 goto cleanup;
 885
 886         if (info->params.mode == MGSL_MODE_RAW ||
 887             info->params.mode == MGSL_MODE_MONOSYNC ||
 888             info->params.mode == MGSL_MODE_BISYNC) {
 889                 unsigned int bufs_needed = (count/DMABUFSIZE);
 890                 unsigned int bufs_free = free_tbuf_count(info);
 891                 if (count % DMABUFSIZE)
 892                         ++bufs_needed;
 893                 if (bufs_needed > bufs_free)
 894                         goto cleanup;
 895         } else {
 896                 if (info->tx_active)
 897                         goto cleanup;
 898                 if (info->tx_count) {
 899                         /* send accumulated data from send_char() calls */
 900                         /* as frame and wait before accepting more data. */
 901                         tx_load(info, info->tx_buf, info->tx_count);
 902                         goto start;
 903                 }
 904         }
 905
 906         ret = info->tx_count = count;
 907         tx_load(info, buf, count);
 908         goto start;
 909
 910 start:
 911         if (info->tx_count && !tty->stopped && !tty->hw_stopped) {
 912                 spin_lock_irqsave(&info->lock,flags);
 913                 if (!info->tx_active)
 914                         tx_start(info);
 915                 spin_unlock_irqrestore(&info->lock,flags);
 916         }
 917
 918 cleanup:
 919         DBGINFO(("%s write rc=%d\n", info->device_name, ret));
 920         return ret;
 921 }
 922
 923 static void put_char(struct tty_struct *tty, unsigned char ch)
 924 {
 925         struct slgt_info *info = tty->driver_data;
 926         unsigned long flags;
 927
 928         if (sanity_check(info, tty->name, "put_char"))
 929                 return;
 930         DBGINFO(("%s put_char(%d)\n", info->device_name, ch));
 931         if (!info->tx_buf)
 932                 return;
 933         spin_lock_irqsave(&info->lock,flags);
 934         if (!info->tx_active && (info->tx_count < info->max_frame_size))
 935                 info->tx_buf[info->tx_count++] = ch;
 936         spin_unlock_irqrestore(&info->lock,flags);
 937 }
 938
 939 static void send_xchar(struct tty_struct *tty, char ch)
 940 {
 941         struct slgt_info *info = tty->driver_data;
 942         unsigned long flags;
 943
 944         if (sanity_check(info, tty->name, "send_xchar"))
 945                 return;
 946         DBGINFO(("%s send_xchar(%d)\n", info->device_name, ch));
 947         info->x_char = ch;
 948         if (ch) {
 949                 spin_lock_irqsave(&info->lock,flags);
 950                 if (!info->tx_enabled)
 951                         tx_start(info);
 952                 spin_unlock_irqrestore(&info->lock,flags);
 953         }
 954 }
 955
 956 static void wait_until_sent(struct tty_struct *tty, int timeout)
 957 {
 958         struct slgt_info *info = tty->driver_data;
 959         unsigned long orig_jiffies, char_time;
 960
 961         if (!info )
 962                 return;
 963         if (sanity_check(info, tty->name, "wait_until_sent"))
 964                 return;
 965         DBGINFO(("%s wait_until_sent entry\n", info->device_name));
 966         if (!(info->flags & ASYNC_INITIALIZED))
 967                 goto exit;
 968
 969         orig_jiffies = jiffies;
 970
 971         /* Set check interval to 1/5 of estimated time to
 972          * send a character, and make it at least 1. The check
 973          * interval should also be less than the timeout.
 974          * Note: use tight timings here to satisfy the NIST-PCTS.
 975          */
 976
 977         if (info->params.data_rate) {
 978                 char_time = info->timeout/(32 * 5);
 979                 if (!char_time)
 980                         char_time++;
 981         } else
 982                 char_time = 1;
 983
 984         if (timeout)
 985                 char_time = min_t(unsigned long, char_time, timeout);
 986
 987         while (info->tx_active) {
 988                 msleep_interruptible(jiffies_to_msecs(char_time));
 989                 if (signal_pending(current))
 990                         break;
 991                 if (timeout && time_after(jiffies, orig_jiffies + timeout))
 992                         break;
 993         }
 994
 995 exit:
 996         DBGINFO(("%s wait_until_sent exit\n", info->device_name));
 997 }
 998
 999 static int write_room(struct tty_struct *tty)
1000 {
1001         struct slgt_info *info = tty->driver_data;
1002         int ret;
1003
1004         if (sanity_check(info, tty->name, "write_room"))
1005                 return 0;
1006         ret = (info->tx_active) ? 0 : HDLC_MAX_FRAME_SIZE;
1007         DBGINFO(("%s write_room=%d\n", info->device_name, ret));
1008         return ret;
1009 }
1010
1011 static void flush_chars(struct tty_struct *tty)
1012 {
1013         struct slgt_info *info = tty->driver_data;
1014         unsigned long flags;
1015
1016         if (sanity_check(info, tty->name, "flush_chars"))
1017                 return;
1018         DBGINFO(("%s flush_chars entry tx_count=%d\n", info->device_name, info->tx_count));
1019
1020         if (info->tx_count <= 0 || tty->stopped ||
1021             tty->hw_stopped || !info->tx_buf)
1022                 return;
1023
1024         DBGINFO(("%s flush_chars start transmit\n", info->device_name));
1025
1026         spin_lock_irqsave(&info->lock,flags);
1027         if (!info->tx_active && info->tx_count) {
1028                 tx_load(info, info->tx_buf,info->tx_count);
1029                 tx_start(info);
1030         }
1031         spin_unlock_irqrestore(&info->lock,flags);
1032 }
1033
1034 static void flush_buffer(struct tty_struct *tty)
1035 {
1036         struct slgt_info *info = tty->driver_data;
1037         unsigned long flags;
1038
1039         if (sanity_check(info, tty->name, "flush_buffer"))
1040                 return;
1041         DBGINFO(("%s flush_buffer\n", info->device_name));
1042
1043         spin_lock_irqsave(&info->lock,flags);
1044         if (!info->tx_active)
1045                 info->tx_count = 0;
1046         spin_unlock_irqrestore(&info->lock,flags);
1047
1048         tty_wakeup(tty);
1049 }
1050
1051 /*
1052  * throttle (stop) transmitter
1053  */
1054 static void tx_hold(struct tty_struct *tty)
1055 {
1056         struct slgt_info *info = tty->driver_data;
1057         unsigned long flags;
1058
1059         if (sanity_check(info, tty->name, "tx_hold"))
1060                 return;
1061         DBGINFO(("%s tx_hold\n", info->device_name));
1062         spin_lock_irqsave(&info->lock,flags);
1063         if (info->tx_enabled && info->params.mode == MGSL_MODE_ASYNC)
1064                 tx_stop(info);
1065         spin_unlock_irqrestore(&info->lock,flags);
1066 }
1067
1068 /*
1069  * release (start) transmitter
1070  */
1071 static void tx_release(struct tty_struct *tty)
1072 {
1073         struct slgt_info *info = tty->driver_data;
1074         unsigned long flags;
1075
1076         if (sanity_check(info, tty->name, "tx_release"))
1077                 return;
1078         DBGINFO(("%s tx_release\n", info->device_name));
1079         spin_lock_irqsave(&info->lock,flags);
1080         if (!info->tx_active && info->tx_count) {
1081                 tx_load(info, info->tx_buf, info->tx_count);
1082                 tx_start(info);
1083         }
1084         spin_unlock_irqrestore(&info->lock,flags);
1085 }
1086
1087 /*
1088  * Service an IOCTL request
1089  *
1090  * Arguments
1091  *
1092  *      tty     pointer to tty instance data
1093  *      file    pointer to associated file object for device
1094  *      cmd     IOCTL command code
1095  *      arg     command argument/context
1096  *
1097  * Return 0 if success, otherwise error code
1098  */
1099 static int ioctl(struct tty_struct *tty, struct file *file,
1100                  unsigned int cmd, unsigned long arg)
1101 {
1102         struct slgt_info *info = tty->driver_data;
1103         struct mgsl_icount cnow;        /* kernel counter temps */
1104         struct serial_icounter_struct __user *p_cuser;  /* user space */
1105         unsigned long flags;
1106         void __user *argp = (void __user *)arg;
1107
1108         if (sanity_check(info, tty->name, "ioctl"))
1109                 return -ENODEV;
1110         DBGINFO(("%s ioctl() cmd=%08X\n", info->device_name, cmd));
1111
1112         if ((cmd != TIOCGSERIAL) && (cmd != TIOCSSERIAL) &&
1113             (cmd != TIOCMIWAIT) && (cmd != TIOCGICOUNT)) {
1114                 if (tty->flags & (1 << TTY_IO_ERROR))
1115                     return -EIO;
1116         }
1117
1118         switch (cmd) {
1119         case MGSL_IOCGPARAMS:
1120                 return get_params(info, argp);
1121         case MGSL_IOCSPARAMS:
1122                 return set_params(info, argp);
1123         case MGSL_IOCGTXIDLE:
1124                 return get_txidle(info, argp);
1125         case MGSL_IOCSTXIDLE:
1126                 return set_txidle(info, (int)arg);
1127         case MGSL_IOCTXENABLE:
1128                 return tx_enable(info, (int)arg);
1129         case MGSL_IOCRXENABLE:
1130                 return rx_enable(info, (int)arg);
1131         case MGSL_IOCTXABORT:
1132                 return tx_abort(info);
1133         case MGSL_IOCGSTATS:
1134                 return get_stats(info, argp);
1135         case MGSL_IOCWAITEVENT:
1136                 return wait_mgsl_event(info, argp);
1137         case TIOCMIWAIT:
1138                 return modem_input_wait(info,(int)arg);
1139         case MGSL_IOCGIF:
1140                 return get_interface(info, argp);
1141         case MGSL_IOCSIF:
1142                 return set_interface(info,(int)arg);
1143         case MGSL_IOCSGPIO:
1144                 return set_gpio(info, argp);
1145         case MGSL_IOCGGPIO:
1146                 return get_gpio(info, argp);
1147         case MGSL_IOCWAITGPIO:
1148                 return wait_gpio(info, argp);
1149         case TIOCGICOUNT:
1150                 spin_lock_irqsave(&info->lock,flags);
1151                 cnow = info->icount;
1152                 spin_unlock_irqrestore(&info->lock,flags);
1153                 p_cuser = argp;
1154                 if (put_user(cnow.cts, &p_cuser->cts) ||
1155                     put_user(cnow.dsr, &p_cuser->dsr) ||
1156                     put_user(cnow.rng, &p_cuser->rng) ||
1157                     put_user(cnow.dcd, &p_cuser->dcd) ||
1158                     put_user(cnow.rx, &p_cuser->rx) ||
1159                     put_user(cnow.tx, &p_cuser->tx) ||
1160                     put_user(cnow.frame, &p_cuser->frame) ||
1161                     put_user(cnow.overrun, &p_cuser->overrun) ||
1162                     put_user(cnow.parity, &p_cuser->parity) ||
1163                     put_user(cnow.brk, &p_cuser->brk) ||
1164                     put_user(cnow.buf_overrun, &p_cuser->buf_overrun))
1165                         return -EFAULT;
1166                 return 0;
1167         default:
1168                 return -ENOIOCTLCMD;
1169         }
1170         return 0;
1171 }
1172
1173 /*
1174  * proc fs support
1175  */
1176 static inline int line_info(char *buf, struct slgt_info *info)
1177 {
1178         char stat_buf[30];
1179         int ret;
1180         unsigned long flags;
1181
1182         ret = sprintf(buf, "%s: IO=%08X IRQ=%d MaxFrameSize=%u\n",
1183                       info->device_name, info->phys_reg_addr,
1184                       info->irq_level, info->max_frame_size);
1185
1186         /* output current serial signal states */
1187         spin_lock_irqsave(&info->lock,flags);
1188         get_signals(info);
1189         spin_unlock_irqrestore(&info->lock,flags);
1190
1191         stat_buf[0] = 0;
1192         stat_buf[1] = 0;
1193         if (info->signals & SerialSignal_RTS)
1194                 strcat(stat_buf, "|RTS");
1195         if (info->signals & SerialSignal_CTS)
1196                 strcat(stat_buf, "|CTS");
1197         if (info->signals & SerialSignal_DTR)
1198                 strcat(stat_buf, "|DTR");
1199         if (info->signals & SerialSignal_DSR)
1200                 strcat(stat_buf, "|DSR");
1201         if (info->signals & SerialSignal_DCD)
1202                 strcat(stat_buf, "|CD");
1203         if (info->signals & SerialSignal_RI)
1204                 strcat(stat_buf, "|RI");
1205
1206         if (info->params.mode != MGSL_MODE_ASYNC) {
1207                 ret += sprintf(buf+ret, "\tHDLC txok:%d rxok:%d",
1208                                info->icount.txok, info->icount.rxok);
1209                 if (info->icount.txunder)
1210                         ret += sprintf(buf+ret, " txunder:%d", info->icount.txunder);
1211                 if (info->icount.txabort)
1212                         ret += sprintf(buf+ret, " txabort:%d", info->icount.txabort);
1213                 if (info->icount.rxshort)
1214                         ret += sprintf(buf+ret, " rxshort:%d", info->icount.rxshort);
1215                 if (info->icount.rxlong)
1216                         ret += sprintf(buf+ret, " rxlong:%d", info->icount.rxlong);
1217                 if (info->icount.rxover)
1218                         ret += sprintf(buf+ret, " rxover:%d", info->icount.rxover);
1219                 if (info->icount.rxcrc)
1220                         ret += sprintf(buf+ret, " rxcrc:%d", info->icount.rxcrc);
1221         } else {
1222                 ret += sprintf(buf+ret, "\tASYNC tx:%d rx:%d",
1223                                info->icount.tx, info->icount.rx);
1224                 if (info->icount.frame)
1225                         ret += sprintf(buf+ret, " fe:%d", info->icount.frame);
1226                 if (info->icount.parity)
1227                         ret += sprintf(buf+ret, " pe:%d", info->icount.parity);
1228                 if (info->icount.brk)
1229                         ret += sprintf(buf+ret, " brk:%d", info->icount.brk);
1230                 if (info->icount.overrun)
1231                         ret += sprintf(buf+ret, " oe:%d", info->icount.overrun);
1232         }
1233
1234         /* Append serial signal status to end */
1235         ret += sprintf(buf+ret, " %s\n", stat_buf+1);
1236
1237         ret += sprintf(buf+ret, "\ttxactive=%d bh_req=%d bh_run=%d pending_bh=%x\n",
1238                        info->tx_active,info->bh_requested,info->bh_running,
1239                        info->pending_bh);
1240
1241         return ret;
1242 }
1243
1244 /* Called to print information about devices
1245  */
1246 static int read_proc(char *page, char **start, off_t off, int count,
1247                      int *eof, void *data)
1248 {
1249         int len = 0, l;
1250         off_t   begin = 0;
1251         struct slgt_info *info;
1252
1253         len += sprintf(page, "synclink_gt driver:%s\n", driver_version);
1254
1255         info = slgt_device_list;
1256         while( info ) {
1257                 l = line_info(page + len, info);
1258                 len += l;
1259                 if (len+begin > off+count)
1260                         goto done;
1261                 if (len+begin < off) {
1262                         begin += len;
1263                         len = 0;
1264                 }
1265                 info = info->next_device;
1266         }
1267
1268         *eof = 1;
1269 done:
1270         if (off >= len+begin)
1271                 return 0;
1272         *start = page + (off-begin);
1273         return ((count < begin+len-off) ? count : begin+len-off);
1274 }
1275
1276 /*
1277  * return count of bytes in transmit buffer
1278  */
1279 static int chars_in_buffer(struct tty_struct *tty)
1280 {
1281         struct slgt_info *info = tty->driver_data;
1282         if (sanity_check(info, tty->name, "chars_in_buffer"))
1283                 return 0;
1284         DBGINFO(("%s chars_in_buffer()=%d\n", info->device_name, info->tx_count));
1285         return info->tx_count;
1286 }
1287
1288 /*
1289  * signal remote device to throttle send data (our receive data)
1290  */
1291 static void throttle(struct tty_struct * tty)
1292 {
1293         struct slgt_info *info = tty->driver_data;
1294         unsigned long flags;
1295
1296         if (sanity_check(info, tty->name, "throttle"))
1297                 return;
1298         DBGINFO(("%s throttle\n", info->device_name));
1299         if (I_IXOFF(tty))
1300                 send_xchar(tty, STOP_CHAR(tty));
1301         if (tty->termios->c_cflag & CRTSCTS) {
1302                 spin_lock_irqsave(&info->lock,flags);
1303                 info->signals &= ~SerialSignal_RTS;
1304                 set_signals(info);
1305                 spin_unlock_irqrestore(&info->lock,flags);
1306         }
1307 }
1308
1309 /*
1310  * signal remote device to stop throttling send data (our receive data)
1311  */
1312 static void unthrottle(struct tty_struct * tty)
1313 {
1314         struct slgt_info *info = tty->driver_data;
1315         unsigned long flags;
1316
1317         if (sanity_check(info, tty->name, "unthrottle"))
1318                 return;
1319         DBGINFO(("%s unthrottle\n", info->device_name));
1320         if (I_IXOFF(tty)) {
1321                 if (info->x_char)
1322                         info->x_char = 0;
1323                 else
1324                         send_xchar(tty, START_CHAR(tty));
1325         }
1326         if (tty->termios->c_cflag & CRTSCTS) {
1327                 spin_lock_irqsave(&info->lock,flags);
1328                 info->signals |= SerialSignal_RTS;
1329                 set_signals(info);
1330                 spin_unlock_irqrestore(&info->lock,flags);
1331         }
1332 }
1333
1334 /*
1335  * set or clear transmit break condition
1336  * break_state  -1=set break condition, 0=clear
1337  */
1338 static void set_break(struct tty_struct *tty, int break_state)
1339 {
1340         struct slgt_info *info = tty->driver_data;
1341         unsigned short value;
1342         unsigned long flags;
1343
1344         if (sanity_check(info, tty->name, "set_break"))
1345                 return;
1346         DBGINFO(("%s set_break(%d)\n", info->device_name, break_state));
1347
1348         spin_lock_irqsave(&info->lock,flags);
1349         value = rd_reg16(info, TCR);
1350         if (break_state == -1)
1351                 value |= BIT6;
1352         else
1353                 value &= ~BIT6;
1354         wr_reg16(info, TCR, value);
1355         spin_unlock_irqrestore(&info->lock,flags);
1356 }
1357
1358 #if SYNCLINK_GENERIC_HDLC
1359
1360 /**
1361  * called by generic HDLC layer when protocol selected (PPP, frame relay, etc.)
1362  * set encoding and frame check sequence (FCS) options
1363  *
1364  * dev       pointer to network device structure
1365  * encoding  serial encoding setting
1366  * parity    FCS setting
1367  *
1368  * returns 0 if success, otherwise error code
1369  */
1370 static int hdlcdev_attach(struct net_device *dev, unsigned short encoding,
1371                           unsigned short parity)
1372 {
1373         struct slgt_info *info = dev_to_port(dev);
1374         unsigned char  new_encoding;
1375         unsigned short new_crctype;
1376
1377         /* return error if TTY interface open */
1378         if (info->count)
1379                 return -EBUSY;
1380
1381         DBGINFO(("%s hdlcdev_attach\n", info->device_name));
1382
1383         switch (encoding)
1384         {
1385         case ENCODING_NRZ:        new_encoding = HDLC_ENCODING_NRZ; break;
1386         case ENCODING_NRZI:       new_encoding = HDLC_ENCODING_NRZI_SPACE; break;
1387         case ENCODING_FM_MARK:    new_encoding = HDLC_ENCODING_BIPHASE_MARK; break;
1388         case ENCODING_FM_SPACE:   new_encoding = HDLC_ENCODING_BIPHASE_SPACE; break;
1389         case ENCODING_MANCHESTER: new_encoding = HDLC_ENCODING_BIPHASE_LEVEL; break;
1390         default: return -EINVAL;
1391         }
1392
1393         switch (parity)
1394         {
1395         case PARITY_NONE:            new_crctype = HDLC_CRC_NONE; break;
1396         case PARITY_CRC16_PR1_CCITT: new_crctype = HDLC_CRC_16_CCITT; break;
1397         case PARITY_CRC32_PR1_CCITT: new_crctype = HDLC_CRC_32_CCITT; break;
1398         default: return -EINVAL;
1399         }
1400
1401         info->params.encoding = new_encoding;
1402         info->params.crc_type = new_crctype;
1403
1404         /* if network interface up, reprogram hardware */
1405         if (info->netcount)
1406                 program_hw(info);
1407
1408         return 0;
1409 }
1410
1411 /**
1412  * called by generic HDLC layer to send frame
1413  *
1414  * skb  socket buffer containing HDLC frame
1415  * dev  pointer to network device structure
1416  *
1417  * returns 0 if success, otherwise error code
1418  */
1419 static int hdlcdev_xmit(struct sk_buff *skb, struct net_device *dev)
1420 {
1421         struct slgt_info *info = dev_to_port(dev);
1422         struct net_device_stats *stats = hdlc_stats(dev);
1423         unsigned long flags;
1424
1425         DBGINFO(("%s hdlc_xmit\n", dev->name));
1426
1427         /* stop sending until this frame completes */
1428         netif_stop_queue(dev);
1429
1430         /* copy data to device buffers */
1431         info->tx_count = skb->len;
1432         tx_load(info, skb->data, skb->len);
1433
1434         /* update network statistics */
1435         stats->tx_packets++;
1436         stats->tx_bytes += skb->len;
1437
1438         /* done with socket buffer, so free it */
1439         dev_kfree_skb(skb);
1440
1441         /* save start time for transmit timeout detection */
1442         dev->trans_start = jiffies;
1443
1444         /* start hardware transmitter if necessary */
1445         spin_lock_irqsave(&info->lock,flags);
1446         if (!info->tx_active)
1447                 tx_start(info);
1448         spin_unlock_irqrestore(&info->lock,flags);
1449
1450         return 0;
1451 }
1452
1453 /**
1454  * called by network layer when interface enabled
1455  * claim resources and initialize hardware
1456  *
1457  * dev  pointer to network device structure
1458  *
1459  * returns 0 if success, otherwise error code
1460  */
1461 static int hdlcdev_open(struct net_device *dev)
1462 {
1463         struct slgt_info *info = dev_to_port(dev);
1464         int rc;
1465         unsigned long flags;
1466
1467         DBGINFO(("%s hdlcdev_open\n", dev->name));
1468
1469         /* generic HDLC layer open processing */
1470         if ((rc = hdlc_open(dev)))
1471                 return rc;
1472
1473         /* arbitrate between network and tty opens */
1474         spin_lock_irqsave(&info->netlock, flags);
1475         if (info->count != 0 || info->netcount != 0) {
1476                 DBGINFO(("%s hdlc_open busy\n", dev->name));
1477                 spin_unlock_irqrestore(&info->netlock, flags);
1478                 return -EBUSY;
1479         }
1480         info->netcount=1;
1481         spin_unlock_irqrestore(&info->netlock, flags);
1482
1483         /* claim resources and init adapter */
1484         if ((rc = startup(info)) != 0) {
1485                 spin_lock_irqsave(&info->netlock, flags);
1486                 info->netcount=0;
1487                 spin_unlock_irqrestore(&info->netlock, flags);
1488                 return rc;
1489         }
1490
1491         /* assert DTR and RTS, apply hardware settings */
1492         info->signals |= SerialSignal_RTS + SerialSignal_DTR;
1493         program_hw(info);
1494
1495         /* enable network layer transmit */
1496         dev->trans_start = jiffies;
1497         netif_start_queue(dev);
1498
1499         /* inform generic HDLC layer of current DCD status */
1500         spin_lock_irqsave(&info->lock, flags);
1501         get_signals(info);
1502         spin_unlock_irqrestore(&info->lock, flags);
1503         if (info->signals & SerialSignal_DCD)
1504                 netif_carrier_on(dev);
1505         else
1506                 netif_carrier_off(dev);
1507         return 0;
1508 }
1509
1510 /**
1511  * called by network layer when interface is disabled
1512  * shutdown hardware and release resources
1513  *
1514  * dev  pointer to network device structure
1515  *
1516  * returns 0 if success, otherwise error code
1517  */
1518 static int hdlcdev_close(struct net_device *dev)
1519 {
1520         struct slgt_info *info = dev_to_port(dev);
1521         unsigned long flags;
1522
1523         DBGINFO(("%s hdlcdev_close\n", dev->name));
1524
1525         netif_stop_queue(dev);
1526
1527         /* shutdown adapter and release resources */
1528         shutdown(info);
1529
1530         hdlc_close(dev);
1531
1532         spin_lock_irqsave(&info->netlock, flags);
1533         info->netcount=0;
1534         spin_unlock_irqrestore(&info->netlock, flags);
1535
1536         return 0;
1537 }
1538
1539 /**
1540  * called by network layer to process IOCTL call to network device
1541  *
1542  * dev  pointer to network device structure
1543  * ifr  pointer to network interface request structure
1544  * cmd  IOCTL command code
1545  *
1546  * returns 0 if success, otherwise error code
1547  */
1548 static int hdlcdev_ioctl(struct net_device *dev, struct ifreq *ifr, int cmd)
1549 {
1550         const size_t size = sizeof(sync_serial_settings);
1551         sync_serial_settings new_line;
1552         sync_serial_settings __user *line = ifr->ifr_settings.ifs_ifsu.sync;
1553         struct slgt_info *info = dev_to_port(dev);
1554         unsigned int flags;
1555
1556         DBGINFO(("%s hdlcdev_ioctl\n", dev->name));
1557
1558         /* return error if TTY interface open */
1559         if (info->count)
1560                 return -EBUSY;
1561
1562         if (cmd != SIOCWANDEV)
1563                 return hdlc_ioctl(dev, ifr, cmd);
1564
1565         switch(ifr->ifr_settings.type) {
1566         case IF_GET_IFACE: /* return current sync_serial_settings */
1567
1568                 ifr->ifr_settings.type = IF_IFACE_SYNC_SERIAL;
1569                 if (ifr->ifr_settings.size < size) {
1570                         ifr->ifr_settings.size = size; /* data size wanted */
1571                         return -ENOBUFS;
1572                 }
1573
1574                 flags = info->params.flags & (HDLC_FLAG_RXC_RXCPIN | HDLC_FLAG_RXC_DPLL |
1575                                               HDLC_FLAG_RXC_BRG    | HDLC_FLAG_RXC_TXCPIN |
1576                                               HDLC_FLAG_TXC_TXCPIN | HDLC_FLAG_TXC_DPLL |
1577                                               HDLC_FLAG_TXC_BRG    | HDLC_FLAG_TXC_RXCPIN);
1578
1579                 switch (flags){
1580                 case (HDLC_FLAG_RXC_RXCPIN | HDLC_FLAG_TXC_TXCPIN): new_line.clock_type = CLOCK_EXT; break;
1581                 case (HDLC_FLAG_RXC_BRG    | HDLC_FLAG_TXC_BRG):    new_line.clock_type = CLOCK_INT; break;
1582                 case (HDLC_FLAG_RXC_RXCPIN | HDLC_FLAG_TXC_BRG):    new_line.clock_type = CLOCK_TXINT; break;
1583                 case (HDLC_FLAG_RXC_RXCPIN | HDLC_FLAG_TXC_RXCPIN): new_line.clock_type = CLOCK_TXFROMRX; break;
1584                 default: new_line.clock_type = CLOCK_DEFAULT;
1585                 }
1586
1587                 new_line.clock_rate = info->params.clock_speed;
1588                 new_line.loopback   = info->params.loopback ? 1:0;
1589
1590                 if (copy_to_user(line, &new_line, size))
1591                         return -EFAULT;
1592                 return 0;
1593
1594         case IF_IFACE_SYNC_SERIAL: /* set sync_serial_settings */
1595
1596                 if(!capable(CAP_NET_ADMIN))
1597                         return -EPERM;
1598                 if (copy_from_user(&new_line, line, size))
1599                         return -EFAULT;
1600
1601                 switch (new_line.clock_type)
1602                 {
1603                 case CLOCK_EXT:      flags = HDLC_FLAG_RXC_RXCPIN | HDLC_FLAG_TXC_TXCPIN; break;
1604                 case CLOCK_TXFROMRX: flags = HDLC_FLAG_RXC_RXCPIN | HDLC_FLAG_TXC_RXCPIN; break;
1605                 case CLOCK_INT:      flags = HDLC_FLAG_RXC_BRG    | HDLC_FLAG_TXC_BRG;    break;
1606                 case CLOCK_TXINT:    flags = HDLC_FLAG_RXC_RXCPIN | HDLC_FLAG_TXC_BRG;    break;
1607                 case CLOCK_DEFAULT:  flags = info->params.flags &
1608                                              (HDLC_FLAG_RXC_RXCPIN | HDLC_FLAG_RXC_DPLL |
1609                                               HDLC_FLAG_RXC_BRG    | HDLC_FLAG_RXC_TXCPIN |
1610                                               HDLC_FLAG_TXC_TXCPIN | HDLC_FLAG_TXC_DPLL |
1611                                               HDLC_FLAG_TXC_BRG    | HDLC_FLAG_TXC_RXCPIN); break;
1612                 default: return -EINVAL;
1613                 }
1614
1615                 if (new_line.loopback != 0 && new_line.loopback != 1)
1616                         return -EINVAL;
1617
1618                 info->params.flags &= ~(HDLC_FLAG_RXC_RXCPIN | HDLC_FLAG_RXC_DPLL |
1619                                         HDLC_FLAG_RXC_BRG    | HDLC_FLAG_RXC_TXCPIN |
1620                                         HDLC_FLAG_TXC_TXCPIN | HDLC_FLAG_TXC_DPLL |
1621                                         HDLC_FLAG_TXC_BRG    | HDLC_FLAG_TXC_RXCPIN);
1622                 info->params.flags |= flags;
1623
1624                 info->params.loopback = new_line.loopback;
1625
1626                 if (flags & (HDLC_FLAG_RXC_BRG | HDLC_FLAG_TXC_BRG))
1627                         info->params.clock_speed = new_line.clock_rate;
1628                 else
1629                         info->params.clock_speed = 0;
1630
1631                 /* if network interface up, reprogram hardware */
1632                 if (info->netcount)
1633                         program_hw(info);
1634                 return 0;
1635
1636         default:
1637                 return hdlc_ioctl(dev, ifr, cmd);
1638         }
1639 }
1640
1641 /**
1642  * called by network layer when transmit timeout is detected
1643  *
1644  * dev  pointer to network device structure
1645  */
1646 static void hdlcdev_tx_timeout(struct net_device *dev)
1647 {
1648         struct slgt_info *info = dev_to_port(dev);
1649         struct net_device_stats *stats = hdlc_stats(dev);
1650         unsigned long flags;
1651
1652         DBGINFO(("%s hdlcdev_tx_timeout\n", dev->name));
1653
1654         stats->tx_errors++;
1655         stats->tx_aborted_errors++;
1656
1657         spin_lock_irqsave(&info->lock,flags);
1658         tx_stop(info);
1659         spin_unlock_irqrestore(&info->lock,flags);
1660
1661         netif_wake_queue(dev);
1662 }
1663
1664 /**
1665  * called by device driver when transmit completes
1666  * reenable network layer transmit if stopped
1667  *
1668  * info  pointer to device instance information
1669  */
1670 static void hdlcdev_tx_done(struct slgt_info *info)
1671 {
1672         if (netif_queue_stopped(info->netdev))
1673                 netif_wake_queue(info->netdev);
1674 }
1675
1676 /**
1677  * called by device driver when frame received
1678  * pass frame to network layer
1679  *
1680  * info  pointer to device instance information
1681  * buf   pointer to buffer contianing frame data
1682  * size  count of data bytes in buf
1683  */
1684 static void hdlcdev_rx(struct slgt_info *info, char *buf, int size)
1685 {
1686         struct sk_buff *skb = dev_alloc_skb(size);
1687         struct net_device *dev = info->netdev;
1688         struct net_device_stats *stats = hdlc_stats(dev);
1689
1690         DBGINFO(("%s hdlcdev_rx\n", dev->name));
1691
1692         if (skb == NULL) {
1693                 DBGERR(("%s: can't alloc skb, drop packet\n", dev->name));
1694                 stats->rx_dropped++;
1695                 return;
1696         }
1697
1698         memcpy(skb_put(skb, size),buf,size);
1699
1700         skb->protocol = hdlc_type_trans(skb, info->netdev);
1701
1702         stats->rx_packets++;
1703         stats->rx_bytes += size;
1704
1705         netif_rx(skb);
1706
1707         info->netdev->last_rx = jiffies;
1708 }
1709
1710 /**
1711  * called by device driver when adding device instance
1712  * do generic HDLC initialization
1713  *
1714  * info  pointer to device instance information
1715  *
1716  * returns 0 if success, otherwise error code
1717  */
1718 static int hdlcdev_init(struct slgt_info *info)
1719 {
1720         int rc;
1721         struct net_device *dev;
1722         hdlc_device *hdlc;
1723
1724         /* allocate and initialize network and HDLC layer objects */
1725
1726         if (!(dev = alloc_hdlcdev(info))) {
1727                 printk(KERN_ERR "%s hdlc device alloc failure\n", info->device_name);
1728                 return -ENOMEM;
1729         }
1730
1731         /* for network layer reporting purposes only */
1732         dev->mem_start = info->phys_reg_addr;
1733         dev->mem_end   = info->phys_reg_addr + SLGT_REG_SIZE - 1;
1734         dev->irq       = info->irq_level;
1735
1736         /* network layer callbacks and settings */
1737         dev->do_ioctl       = hdlcdev_ioctl;
1738         dev->open           = hdlcdev_open;
1739         dev->stop           = hdlcdev_close;
1740         dev->tx_timeout     = hdlcdev_tx_timeout;
1741         dev->watchdog_timeo = 10*HZ;
1742         dev->tx_queue_len   = 50;
1743
1744         /* generic HDLC layer callbacks and settings */
1745         hdlc         = dev_to_hdlc(dev);
1746         hdlc->attach = hdlcdev_attach;
1747         hdlc->xmit   = hdlcdev_xmit;
1748
1749         /* register objects with HDLC layer */
1750         if ((rc = register_hdlc_device(dev))) {
1751                 printk(KERN_WARNING "%s:unable to register hdlc device\n",__FILE__);
1752                 free_netdev(dev);
1753                 return rc;
1754         }
1755
1756         info->netdev = dev;
1757         return 0;
1758 }
1759
1760 /**
1761  * called by device driver when removing device instance
1762  * do generic HDLC cleanup
1763  *
1764  * info  pointer to device instance information
1765  */
1766 static void hdlcdev_exit(struct slgt_info *info)
1767 {
1768         unregister_hdlc_device(info->netdev);
1769         free_netdev(info->netdev);
1770         info->netdev = NULL;
1771 }
1772
1773 #endif /* ifdef CONFIG_HDLC */
1774
1775 /*
1776  * get async data from rx DMA buffers
1777  */
1778 static void rx_async(struct slgt_info *info)
1779 {
1780         struct tty_struct *tty = info->tty;
1781         struct mgsl_icount *icount = &info->icount;
1782         unsigned int start, end;
1783         unsigned char *p;
1784         unsigned char status;
1785         struct slgt_desc *bufs = info->rbufs;
1786         int i, count;
1787         int chars = 0;
1788         int stat;
1789         unsigned char ch;
1790
1791         start = end = info->rbuf_current;
1792
1793         while(desc_complete(bufs[end])) {
1794                 count = desc_count(bufs[end]) - info->rbuf_index;
1795                 p     = bufs[end].buf + info->rbuf_index;
1796
1797                 DBGISR(("%s rx_async count=%d\n", info->device_name, count));
1798                 DBGDATA(info, p, count, "rx");
1799
1800                 for(i=0 ; i < count; i+=2, p+=2) {
1801                         ch = *p;
1802                         icount->rx++;
1803
1804                         stat = 0;
1805
1806                         if ((status = *(p+1) & (BIT1 + BIT0))) {
1807                                 if (status & BIT1)
1808                                         icount->parity++;
1809                                 else if (status & BIT0)
1810                                         icount->frame++;
1811                                 /* discard char if tty control flags say so */
1812                                 if (status & info->ignore_status_mask)
1813                                         continue;
1814                                 if (status & BIT1)
1815                                         stat = TTY_PARITY;
1816                                 else if (status & BIT0)
1817                                         stat = TTY_FRAME;
1818                         }
1819                         if (tty) {
1820                                 tty_insert_flip_char(tty, ch, stat);
1821                                 chars++;
1822                         }
1823                 }
1824
1825                 if (i < count) {
1826                         /* receive buffer not completed */
1827                         info->rbuf_index += i;
1828                         mod_timer(&info->rx_timer, jiffies + 1);
1829                         break;
1830                 }
1831
1832                 info->rbuf_index = 0;
1833                 free_rbufs(info, end, end);
1834
1835                 if (++end == info->rbuf_count)
1836                         end = 0;
1837
1838                 /* if entire list searched then no frame available */
1839                 if (end == start)
1840                         break;
1841         }
1842
1843         if (tty && chars)
1844                 tty_flip_buffer_push(tty);
1845 }
1846
1847 /*
1848  * return next bottom half action to perform
1849  */
1850 static int bh_action(struct slgt_info *info)
1851 {
1852         unsigned long flags;
1853         int rc;
1854
1855         spin_lock_irqsave(&info->lock,flags);
1856
1857         if (info->pending_bh & BH_RECEIVE) {
1858                 info->pending_bh &= ~BH_RECEIVE;
1859                 rc = BH_RECEIVE;
1860         } else if (info->pending_bh & BH_TRANSMIT) {
1861                 info->pending_bh &= ~BH_TRANSMIT;
1862                 rc = BH_TRANSMIT;
1863         } else if (info->pending_bh & BH_STATUS) {
1864                 info->pending_bh &= ~BH_STATUS;
1865                 rc = BH_STATUS;
1866         } else {
1867                 /* Mark BH routine as complete */
1868                 info->bh_running   = 0;
1869                 info->bh_requested = 0;
1870                 rc = 0;
1871         }
1872
1873         spin_unlock_irqrestore(&info->lock,flags);
1874
1875         return rc;
1876 }
1877
1878 /*
1879  * perform bottom half processing
1880  */
1881 static void bh_handler(struct work_struct *work)
1882 {
1883         struct slgt_info *info = container_of(work, struct slgt_info, task);
1884         int action;
1885
1886         if (!info)
1887                 return;
1888         info->bh_running = 1;
1889
1890         while((action = bh_action(info))) {
1891                 switch (action) {
1892                 case BH_RECEIVE:
1893                         DBGBH(("%s bh receive\n", info->device_name));
1894                         switch(info->params.mode) {
1895                         case MGSL_MODE_ASYNC:
1896                                 rx_async(info);
1897                                 break;
1898                         case MGSL_MODE_HDLC:
1899                                 while(rx_get_frame(info));
1900                                 break;
1901                         case MGSL_MODE_RAW:
1902                         case MGSL_MODE_MONOSYNC:
1903                         case MGSL_MODE_BISYNC:
1904                                 while(rx_get_buf(info));
1905                                 break;
1906                         }
1907                         /* restart receiver if rx DMA buffers exhausted */
1908                         if (info->rx_restart)
1909                                 rx_start(info);
1910                         break;
1911                 case BH_TRANSMIT:
1912                         bh_transmit(info);
1913                         break;
1914                 case BH_STATUS:
1915                         DBGBH(("%s bh status\n", info->device_name));
1916                         info->ri_chkcount = 0;
1917                         info->dsr_chkcount = 0;
1918                         info->dcd_chkcount = 0;
1919                         info->cts_chkcount = 0;
1920                         break;
1921                 default:
1922                         DBGBH(("%s unknown action\n", info->device_name));
1923                         break;
1924                 }
1925         }
1926         DBGBH(("%s bh_handler exit\n", info->device_name));
1927 }
1928
1929 static void bh_transmit(struct slgt_info *info)
1930 {
1931         struct tty_struct *tty = info->tty;
1932
1933         DBGBH(("%s bh_transmit\n", info->device_name));
1934         if (tty)
1935                 tty_wakeup(tty);
1936 }
1937
1938 static void dsr_change(struct slgt_info *info)
1939 {
1940         get_signals(info);
1941         DBGISR(("dsr_change %s signals=%04X\n", info->device_name, info->signals));
1942         if ((info->dsr_chkcount)++ == IO_PIN_SHUTDOWN_LIMIT) {
1943                 slgt_irq_off(info, IRQ_DSR);
1944                 return;
1945         }
1946         info->icount.dsr++;
1947         if (info->signals & SerialSignal_DSR)
1948                 info->input_signal_events.dsr_up++;
1949         else
1950                 info->input_signal_events.dsr_down++;
1951         wake_up_interruptible(&info->status_event_wait_q);
1952         wake_up_interruptible(&info->event_wait_q);
1953         info->pending_bh |= BH_STATUS;
1954 }
1955
1956 static void cts_change(struct slgt_info *info)
1957 {
1958         get_signals(info);
1959         DBGISR(("cts_change %s signals=%04X\n", info->device_name, info->signals));
1960         if ((info->cts_chkcount)++ == IO_PIN_SHUTDOWN_LIMIT) {
1961                 slgt_irq_off(info, IRQ_CTS);
1962                 return;
1963         }
1964         info->icount.cts++;
1965         if (info->signals & SerialSignal_CTS)
1966                 info->input_signal_events.cts_up++;
1967         else
1968                 info->input_signal_events.cts_down++;
1969         wake_up_interruptible(&info->status_event_wait_q);
1970         wake_up_interruptible(&info->event_wait_q);
1971         info->pending_bh |= BH_STATUS;
1972
1973         if (info->flags & ASYNC_CTS_FLOW) {
1974                 if (info->tty) {
1975                         if (info->tty->hw_stopped) {
1976                                 if (info->signals & SerialSignal_CTS) {
1977                                         info->tty->hw_stopped = 0;
1978                                         info->pending_bh |= BH_TRANSMIT;
1979                                         return;
1980                                 }
1981                         } else {
1982                                 if (!(info->signals & SerialSignal_CTS))
1983                                         info->tty->hw_stopped = 1;
1984                         }
1985                 }
1986         }
1987 }
1988
1989 static void dcd_change(struct slgt_info *info)
1990 {
1991         get_signals(info);
1992         DBGISR(("dcd_change %s signals=%04X\n", info->device_name, info->signals));
1993         if ((info->dcd_chkcount)++ == IO_PIN_SHUTDOWN_LIMIT) {
1994                 slgt_irq_off(info, IRQ_DCD);
1995                 return;
1996         }
1997         info->icount.dcd++;
1998         if (info->signals & SerialSignal_DCD) {
1999                 info->input_signal_events.dcd_up++;
2000         } else {
2001                 info->input_signal_events.dcd_down++;
2002         }
2003 #if SYNCLINK_GENERIC_HDLC
2004         if (info->netcount) {
2005                 if (info->signals & SerialSignal_DCD)
2006                         netif_carrier_on(info->netdev);
2007                 else
2008                         netif_carrier_off(info->netdev);
2009         }
2010 #endif
2011         wake_up_interruptible(&info->status_event_wait_q);
2012         wake_up_interruptible(&info->event_wait_q);
2013         info->pending_bh |= BH_STATUS;
2014
2015         if (info->flags & ASYNC_CHECK_CD) {
2016                 if (info->signals & SerialSignal_DCD)
2017                         wake_up_interruptible(&info->open_wait);
2018                 else {
2019                         if (info->tty)
2020                                 tty_hangup(info->tty);
2021                 }
2022         }
2023 }
2024
2025 static void ri_change(struct slgt_info *info)
2026 {
2027         get_signals(info);
2028         DBGISR(("ri_change %s signals=%04X\n", info->device_name, info->signals));
2029         if ((info->ri_chkcount)++ == IO_PIN_SHUTDOWN_LIMIT) {
2030                 slgt_irq_off(info, IRQ_RI);
2031                 return;
2032         }
2033         info->icount.dcd++;
2034         if (info->signals & SerialSignal_RI) {
2035                 info->input_signal_events.ri_up++;
2036         } else {
2037                 info->input_signal_events.ri_down++;
2038         }
2039         wake_up_interruptible(&info->status_event_wait_q);
2040         wake_up_interruptible(&info->event_wait_q);
2041         info->pending_bh |= BH_STATUS;
2042 }
2043
2044 static void isr_serial(struct slgt_info *info)
2045 {
2046         unsigned short status = rd_reg16(info, SSR);
2047
2048         DBGISR(("%s isr_serial status=%04X\n", info->device_name, status));
2049
2050         wr_reg16(info, SSR, status); /* clear pending */
2051
2052         info->irq_occurred = 1;
2053
2054         if (info->params.mode == MGSL_MODE_ASYNC) {
2055                 if (status & IRQ_TXIDLE) {
2056                         if (info->tx_count)
2057                                 isr_txeom(info, status);
2058                 }
2059                 if ((status & IRQ_RXBREAK) && (status & RXBREAK)) {
2060                         info->icount.brk++;
2061                         /* process break detection if tty control allows */
2062                         if (info->tty) {
2063                                 if (!(status & info->ignore_status_mask)) {
2064                                         if (info->read_status_mask & MASK_BREAK) {
2065                                                 tty_insert_flip_char(info->tty, 0, TTY_BREAK);
2066                                                 if (info->flags & ASYNC_SAK)
2067                                                         do_SAK(info->tty);
2068                                         }
2069                                 }
2070                         }
2071                 }
2072         } else {
2073                 if (status & (IRQ_TXIDLE + IRQ_TXUNDER))
2074                         isr_txeom(info, status);
2075
2076                 if (status & IRQ_RXIDLE) {
2077                         if (status & RXIDLE)
2078                                 info->icount.rxidle++;
2079                         else
2080                                 info->icount.exithunt++;
2081                         wake_up_interruptible(&info->event_wait_q);
2082                 }
2083
2084                 if (status & IRQ_RXOVER)
2085                         rx_start(info);
2086         }
2087
2088         if (status & IRQ_DSR)
2089                 dsr_change(info);
2090         if (status & IRQ_CTS)
2091                 cts_change(info);
2092         if (status & IRQ_DCD)
2093                 dcd_change(info);
2094         if (status & IRQ_RI)
2095                 ri_change(info);
2096 }
2097
2098 static void isr_rdma(struct slgt_info *info)
2099 {
2100         unsigned int status = rd_reg32(info, RDCSR);
2101
2102         DBGISR(("%s isr_rdma status=%08x\n", info->device_name, status));
2103
2104         /* RDCSR (rx DMA control/status)
2105          *
2106          * 31..07  reserved
2107          * 06      save status byte to DMA buffer
2108          * 05      error
2109          * 04      eol (end of list)
2110          * 03      eob (end of buffer)
2111          * 02      IRQ enable
2112          * 01      reset
2113          * 00      enable
2114          */
2115         wr_reg32(info, RDCSR, status);  /* clear pending */
2116
2117         if (status & (BIT5 + BIT4)) {
2118                 DBGISR(("%s isr_rdma rx_restart=1\n", info->device_name));
2119                 info->rx_restart = 1;
2120         }
2121         info->pending_bh |= BH_RECEIVE;
2122 }
2123
2124 static void isr_tdma(struct slgt_info *info)
2125 {
2126         unsigned int status = rd_reg32(info, TDCSR);
2127
2128         DBGISR(("%s isr_tdma status=%08x\n", info->device_name, status));
2129
2130         /* TDCSR (tx DMA control/status)
2131          *
2132          * 31..06  reserved
2133          * 05      error
2134          * 04      eol (end of list)
2135          * 03      eob (end of buffer)
2136          * 02      IRQ enable
2137          * 01      reset
2138          * 00      enable
2139          */
2140         wr_reg32(info, TDCSR, status);  /* clear pending */
2141
2142         if (status & (BIT5 + BIT4 + BIT3)) {
2143                 // another transmit buffer has completed
2144                 // run bottom half to get more send data from user
2145                 info->pending_bh |= BH_TRANSMIT;
2146         }
2147 }
2148
2149 static void isr_txeom(struct slgt_info *info, unsigned short status)
2150 {
2151         DBGISR(("%s txeom status=%04x\n", info->device_name, status));
2152
2153         slgt_irq_off(info, IRQ_TXDATA + IRQ_TXIDLE + IRQ_TXUNDER);
2154         tdma_reset(info);
2155         reset_tbufs(info);
2156         if (status & IRQ_TXUNDER) {
2157                 unsigned short val = rd_reg16(info, TCR);
2158                 wr_reg16(info, TCR, (unsigned short)(val | BIT2)); /* set reset bit */
2159                 wr_reg16(info, TCR, val); /* clear reset bit */
2160         }
2161
2162         if (info->tx_active) {
2163                 if (info->params.mode != MGSL_MODE_ASYNC) {
2164                         if (status & IRQ_TXUNDER)
2165                                 info->icount.txunder++;
2166                         else if (status & IRQ_TXIDLE)
2167                                 info->icount.txok++;
2168                 }
2169
2170                 info->tx_active = 0;
2171                 info->tx_count = 0;
2172
2173                 del_timer(&info->tx_timer);
2174
2175                 if (info->params.mode != MGSL_MODE_ASYNC && info->drop_rts_on_tx_done) {
2176                         info->signals &= ~SerialSignal_RTS;
2177                         info->drop_rts_on_tx_done = 0;
2178                         set_signals(info);
2179                 }
2180
2181 #if SYNCLINK_GENERIC_HDLC
2182                 if (info->netcount)
2183                         hdlcdev_tx_done(info);
2184                 else
2185 #endif
2186                 {
2187                         if (info->tty && (info->tty->stopped || info->tty->hw_stopped)) {
2188                                 tx_stop(info);
2189                                 return;
2190                         }
2191                         info->pending_bh |= BH_TRANSMIT;
2192                 }
2193         }
2194 }
2195
2196 static void isr_gpio(struct slgt_info *info, unsigned int changed, unsigned int state)
2197 {
2198         struct cond_wait *w, *prev;
2199
2200         /* wake processes waiting for specific transitions */
2201         for (w = info->gpio_wait_q, prev = NULL ; w != NULL ; w = w->next) {
2202                 if (w->data & changed) {
2203                         w->data = state;
2204                         wake_up_interruptible(&w->q);
2205                         if (prev != NULL)
2206                                 prev->next = w->next;
2207                         else
2208                                 info->gpio_wait_q = w->next;
2209                 } else
2210                         prev = w;
2211         }
2212 }
2213
2214 /* interrupt service routine
2215  *
2216  *      irq     interrupt number
2217  *      dev_id  device ID supplied during interrupt registration
2218  */
2219 static irqreturn_t slgt_interrupt(int irq, void *dev_id)
2220 {
2221         struct slgt_info *info;
2222         unsigned int gsr;
2223         unsigned int i;
2224
2225         DBGISR(("slgt_interrupt irq=%d entry\n", irq));
2226
2227         info = dev_id;
2228         if (!info)
2229                 return IRQ_NONE;
2230
2231         spin_lock(&info->lock);
2232
2233         while((gsr = rd_reg32(info, GSR) & 0xffffff00)) {
2234                 DBGISR(("%s gsr=%08x\n", info->device_name, gsr));
2235                 info->irq_occurred = 1;
2236                 for(i=0; i < info->port_count ; i++) {
2237                         if (info->port_array[i] == NULL)
2238                                 continue;
2239                         if (gsr & (BIT8 << i))
2240                                 isr_serial(info->port_array[i]);
2241                         if (gsr & (BIT16 << (i*2)))
2242                                 isr_rdma(info->port_array[i]);
2243                         if (gsr & (BIT17 << (i*2)))
2244                                 isr_tdma(info->port_array[i]);
2245                 }
2246         }
2247
2248         if (info->gpio_present) {
2249                 unsigned int state;
2250                 unsigned int changed;
2251                 while ((changed = rd_reg32(info, IOSR)) != 0) {
2252                         DBGISR(("%s iosr=%08x\n", info->device_name, changed));
2253                         /* read latched state of GPIO signals */
2254                         state = rd_reg32(info, IOVR);
2255                         /* clear pending GPIO interrupt bits */
2256                         wr_reg32(info, IOSR, changed);
2257                         for (i=0 ; i < info->port_count ; i++) {
2258                                 if (info->port_array[i] != NULL)
2259                                         isr_gpio(info->port_array[i], changed, state);
2260                         }
2261                 }
2262         }
2263
2264         for(i=0; i < info->port_count ; i++) {
2265                 struct slgt_info *port = info->port_array[i];
2266
2267                 if (port && (port->count || port->netcount) &&
2268                     port->pending_bh && !port->bh_running &&
2269                     !port->bh_requested) {
2270                         DBGISR(("%s bh queued\n", port->device_name));
2271                         schedule_work(&port->task);
2272                         port->bh_requested = 1;
2273                 }
2274         }
2275
2276         spin_unlock(&info->lock);
2277
2278         DBGISR(("slgt_interrupt irq=%d exit\n", irq));
2279         return IRQ_HANDLED;
2280 }
2281
2282 static int startup(struct slgt_info *info)
2283 {
2284         DBGINFO(("%s startup\n", info->device_name));
2285
2286         if (info->flags & ASYNC_INITIALIZED)
2287                 return 0;
2288
2289         if (!info->tx_buf) {
2290                 info->tx_buf = kmalloc(info->max_frame_size, GFP_KERNEL);
2291                 if (!info->tx_buf) {
2292                         DBGERR(("%s can't allocate tx buffer\n", info->device_name));
2293                         return -ENOMEM;
2294                 }
2295         }
2296
2297         info->pending_bh = 0;
2298
2299         memset(&info->icount, 0, sizeof(info->icount));
2300
2301         /* program hardware for current parameters */
2302         change_params(info);
2303
2304         if (info->tty)
2305                 clear_bit(TTY_IO_ERROR, &info->tty->flags);
2306
2307         info->flags |= ASYNC_INITIALIZED;
2308
2309         return 0;
2310 }
2311
2312 /*
2313  *  called by close() and hangup() to shutdown hardware
2314  */
2315 static void shutdown(struct slgt_info *info)
2316 {
2317         unsigned long flags;
2318
2319         if (!(info->flags & ASYNC_INITIALIZED))
2320                 return;
2321
2322         DBGINFO(("%s shutdown\n", info->device_name));
2323
2324         /* clear status wait queue because status changes */
2325         /* can't happen after shutting down the hardware */
2326         wake_up_interruptible(&info->status_event_wait_q);
2327         wake_up_interruptible(&info->event_wait_q);
2328
2329         del_timer_sync(&info->tx_timer);
2330         del_timer_sync(&info->rx_timer);
2331
2332         kfree(info->tx_buf);
2333         info->tx_buf = NULL;
2334
2335         spin_lock_irqsave(&info->lock,flags);
2336
2337         tx_stop(info);
2338         rx_stop(info);
2339
2340         slgt_irq_off(info, IRQ_ALL | IRQ_MASTER);
2341
2342         if (!info->tty || info->tty->termios->c_cflag & HUPCL) {
2343                 info->signals &= ~(SerialSignal_DTR + SerialSignal_RTS);
2344                 set_signals(info);
2345         }
2346
2347         flush_cond_wait(&info->gpio_wait_q);
2348
2349         spin_unlock_irqrestore(&info->lock,flags);
2350
2351         if (info->tty)
2352                 set_bit(TTY_IO_ERROR, &info->tty->flags);
2353
2354         info->flags &= ~ASYNC_INITIALIZED;
2355 }
2356
2357 static void program_hw(struct slgt_info *info)
2358 {
2359         unsigned long flags;
2360
2361         spin_lock_irqsave(&info->lock,flags);
2362
2363         rx_stop(info);
2364         tx_stop(info);
2365
2366         if (info->params.mode != MGSL_MODE_ASYNC ||
2367             info->netcount)
2368                 sync_mode(info);
2369         else
2370                 async_mode(info);
2371
2372         set_signals(info);
2373
2374         info->dcd_chkcount = 0;
2375         info->cts_chkcount = 0;
2376         info->ri_chkcount = 0;
2377         info->dsr_chkcount = 0;
2378
2379         slgt_irq_on(info, IRQ_DCD | IRQ_CTS | IRQ_DSR);
2380         get_signals(info);
2381
2382         if (info->netcount ||
2383             (info->tty && info->tty->termios->c_cflag & CREAD))
2384                 rx_start(info);
2385
2386         spin_unlock_irqrestore(&info->lock,flags);
2387 }
2388
2389 /*
2390  * reconfigure adapter based on new parameters
2391  */
2392 static void change_params(struct slgt_info *info)
2393 {
2394         unsigned cflag;
2395         int bits_per_char;
2396
2397         if (!info->tty || !info->tty->termios)
2398                 return;
2399         DBGINFO(("%s change_params\n", info->device_name));
2400
2401         cflag = info->tty->termios->c_cflag;
2402
2403         /* if B0 rate (hangup) specified then negate DTR and RTS */
2404         /* otherwise assert DTR and RTS */
2405         if (cflag & CBAUD)
2406                 info->signals |= SerialSignal_RTS + SerialSignal_DTR;
2407         else
2408                 info->signals &= ~(SerialSignal_RTS + SerialSignal_DTR);
2409
2410         /* byte size and parity */
2411
2412         switch (cflag & CSIZE) {
2413         case CS5: info->params.data_bits = 5; break;
2414         case CS6: info->params.data_bits = 6; break;
2415         case CS7: info->params.data_bits = 7; break;
2416         case CS8: info->params.data_bits = 8; break;
2417         default:  info->params.data_bits = 7; break;
2418         }
2419
2420         info->params.stop_bits = (cflag & CSTOPB) ? 2 : 1;
2421
2422         if (cflag & PARENB)
2423                 info->params.parity = (cflag & PARODD) ? ASYNC_PARITY_ODD : ASYNC_PARITY_EVEN;
2424         else
2425                 info->params.parity = ASYNC_PARITY_NONE;
2426
2427         /* calculate number of jiffies to transmit a full
2428          * FIFO (32 bytes) at specified data rate
2429          */
2430         bits_per_char = info->params.data_bits +
2431                         info->params.stop_bits + 1;
2432
2433         info->params.data_rate = tty_get_baud_rate(info->tty);
2434
2435         if (info->params.data_rate) {
2436                 info->timeout = (32*HZ*bits_per_char) /
2437                                 info->params.data_rate;
2438         }
2439         info->timeout += HZ/50;         /* Add .02 seconds of slop */
2440
2441         if (cflag & CRTSCTS)
2442                 info->flags |= ASYNC_CTS_FLOW;
2443         else
2444                 info->flags &= ~ASYNC_CTS_FLOW;
2445
2446         if (cflag & CLOCAL)
2447                 info->flags &= ~ASYNC_CHECK_CD;
2448         else
2449                 info->flags |= ASYNC_CHECK_CD;
2450
2451         /* process tty input control flags */
2452
2453         info->read_status_mask = IRQ_RXOVER;
2454         if (I_INPCK(info->tty))
2455                 info->read_status_mask |= MASK_PARITY | MASK_FRAMING;
2456         if (I_BRKINT(info->tty) || I_PARMRK(info->tty))
2457                 info->read_status_mask |= MASK_BREAK;
2458         if (I_IGNPAR(info->tty))
2459                 info->ignore_status_mask |= MASK_PARITY | MASK_FRAMING;
2460         if (I_IGNBRK(info->tty)) {
2461                 info->ignore_status_mask |= MASK_BREAK;
2462                 /* If ignoring parity and break indicators, ignore
2463                  * overruns too.  (For real raw support).
2464                  */
2465                 if (I_IGNPAR(info->tty))
2466                         info->ignore_status_mask |= MASK_OVERRUN;
2467         }
2468
2469         program_hw(info);
2470 }
2471
2472 static int get_stats(struct slgt_info *info, struct mgsl_icount __user *user_icount)
2473 {
2474         DBGINFO(("%s get_stats\n",  info->device_name));
2475         if (!user_icount) {
2476                 memset(&info->icount, 0, sizeof(info->icount));
2477         } else {
2478                 if (copy_to_user(user_icount, &info->icount, sizeof(struct mgsl_icount)))
2479                         return -EFAULT;
2480         }
2481         return 0;
2482 }
2483
2484 static int get_params(struct slgt_info *info, MGSL_PARAMS __user *user_params)
2485 {
2486         DBGINFO(("%s get_params\n", info->device_name));
2487         if (copy_to_user(user_params, &info->params, sizeof(MGSL_PARAMS)))
2488                 return -EFAULT;
2489         return 0;
2490 }
2491
2492 static int set_params(struct slgt_info *info, MGSL_PARAMS __user *new_params)
2493 {
2494         unsigned long flags;
2495         MGSL_PARAMS tmp_params;
2496
2497         DBGINFO(("%s set_params\n", info->device_name));
2498         if (copy_from_user(&tmp_params, new_params, sizeof(MGSL_PARAMS)))
2499                 return -EFAULT;
2500
2501         spin_lock_irqsave(&info->lock, flags);
2502         memcpy(&info->params, &tmp_params, sizeof(MGSL_PARAMS));
2503         spin_unlock_irqrestore(&info->lock, flags);
2504
2505         change_params(info);
2506
2507         return 0;
2508 }
2509
2510 static int get_txidle(struct slgt_info *info, int __user *idle_mode)
2511 {
2512         DBGINFO(("%s get_txidle=%d\n", info->device_name, info->idle_mode));
2513         if (put_user(info->idle_mode, idle_mode))
2514                 return -EFAULT;
2515         return 0;
2516 }
2517
2518 static int set_txidle(struct slgt_info *info, int idle_mode)
2519 {
2520         unsigned long flags;
2521         DBGINFO(("%s set_txidle(%d)\n", info->device_name, idle_mode));
2522         spin_lock_irqsave(&info->lock,flags);
2523         info->idle_mode = idle_mode;
2524         if (info->params.mode != MGSL_MODE_ASYNC)
2525                 tx_set_idle(info);
2526         spin_unlock_irqrestore(&info->lock,flags);
2527         return 0;
2528 }
2529
2530 static int tx_enable(struct slgt_info *info, int enable)
2531 {
2532         unsigned long flags;
2533         DBGINFO(("%s tx_enable(%d)\n", info->device_name, enable));
2534         spin_lock_irqsave(&info->lock,flags);
2535         if (enable) {
2536                 if (!info->tx_enabled)
2537                         tx_start(info);
2538         } else {
2539                 if (info->tx_enabled)
2540                         tx_stop(info);
2541         }
2542         spin_unlock_irqrestore(&info->lock,flags);
2543         return 0;
2544 }
2545
2546 /*
2547  * abort transmit HDLC frame
2548  */
2549 static int tx_abort(struct slgt_info *info)
2550 {
2551         unsigned long flags;
2552         DBGINFO(("%s tx_abort\n", info->device_name));
2553         spin_lock_irqsave(&info->lock,flags);
2554         tdma_reset(info);
2555         spin_unlock_irqrestore(&info->lock,flags);
2556         return 0;
2557 }
2558
2559 static int rx_enable(struct slgt_info *info, int enable)
2560 {
2561         unsigned long flags;
2562         DBGINFO(("%s rx_enable(%d)\n", info->device_name, enable));
2563         spin_lock_irqsave(&info->lock,flags);
2564         if (enable) {
2565                 if (!info->rx_enabled)
2566                         rx_start(info);
2567                 else if (enable == 2) {
2568                         /* force hunt mode (write 1 to RCR[3]) */
2569                         wr_reg16(info, RCR, rd_reg16(info, RCR) | BIT3);
2570                 }
2571         } else {
2572                 if (info->rx_enabled)
2573                         rx_stop(info);
2574         }
2575         spin_unlock_irqrestore(&info->lock,flags);
2576         return 0;
2577 }
2578
2579 /*
2580  *  wait for specified event to occur
2581  */
2582 static int wait_mgsl_event(struct slgt_info *info, int __user *mask_ptr)
2583 {
2584         unsigned long flags;
2585         int s;
2586         int rc=0;
2587         struct mgsl_icount cprev, cnow;
2588         int events;
2589         int mask;
2590         struct  _input_signal_events oldsigs, newsigs;
2591         DECLARE_WAITQUEUE(wait, current);
2592
2593         if (get_user(mask, mask_ptr))
2594                 return -EFAULT;
2595
2596         DBGINFO(("%s wait_mgsl_event(%d)\n", info->device_name, mask));
2597
2598         spin_lock_irqsave(&info->lock,flags);
2599
2600         /* return immediately if state matches requested events */
2601         get_signals(info);
2602         s = info->signals;
2603
2604         events = mask &
2605                 ( ((s & SerialSignal_DSR) ? MgslEvent_DsrActive:MgslEvent_DsrInactive) +
2606                   ((s & SerialSignal_DCD) ? MgslEvent_DcdActive:MgslEvent_DcdInactive) +
2607                   ((s & SerialSignal_CTS) ? MgslEvent_CtsActive:MgslEvent_CtsInactive) +
2608                   ((s & SerialSignal_RI)  ? MgslEvent_RiActive :MgslEvent_RiInactive) );
2609         if (events) {
2610                 spin_unlock_irqrestore(&info->lock,flags);
2611                 goto exit;
2612         }
2613
2614         /* save current irq counts */
2615         cprev = info->icount;
2616         oldsigs = info->input_signal_events;
2617
2618         /* enable hunt and idle irqs if needed */
2619         if (mask & (MgslEvent_ExitHuntMode+MgslEvent_IdleReceived)) {
2620                 unsigned short val = rd_reg16(info, SCR);
2621                 if (!(val & IRQ_RXIDLE))
2622                         wr_reg16(info, SCR, (unsigned short)(val | IRQ_RXIDLE));
2623         }
2624
2625         set_current_state(TASK_INTERRUPTIBLE);
2626         add_wait_queue(&info->event_wait_q, &wait);
2627
2628         spin_unlock_irqrestore(&info->lock,flags);
2629
2630         for(;;) {
2631                 schedule();
2632                 if (signal_pending(current)) {
2633                         rc = -ERESTARTSYS;
2634                         break;
2635                 }
2636
2637                 /* get current irq counts */
2638                 spin_lock_irqsave(&info->lock,flags);
2639                 cnow = info->icount;
2640                 newsigs = info->input_signal_events;
2641                 set_current_state(TASK_INTERRUPTIBLE);
2642                 spin_unlock_irqrestore(&info->lock,flags);
2643
2644                 /* if no change, wait aborted for some reason */
2645                 if (newsigs.dsr_up   == oldsigs.dsr_up   &&
2646                     newsigs.dsr_down == oldsigs.dsr_down &&
2647                     newsigs.dcd_up   == oldsigs.dcd_up   &&
2648                     newsigs.dcd_down == oldsigs.dcd_down &&
2649                     newsigs.cts_up   == oldsigs.cts_up   &&
2650                     newsigs.cts_down == oldsigs.cts_down &&
2651                     newsigs.ri_up    == oldsigs.ri_up    &&
2652                     newsigs.ri_down  == oldsigs.ri_down  &&
2653                     cnow.exithunt    == cprev.exithunt   &&
2654                     cnow.rxidle      == cprev.rxidle) {
2655                         rc = -EIO;
2656                         break;
2657                 }
2658
2659                 events = mask &
2660                         ( (newsigs.dsr_up   != oldsigs.dsr_up   ? MgslEvent_DsrActive:0)   +
2661                           (newsigs.dsr_down != oldsigs.dsr_down ? MgslEvent_DsrInactive:0) +
2662                           (newsigs.dcd_up   != oldsigs.dcd_up   ? MgslEvent_DcdActive:0)   +
2663                           (newsigs.dcd_down != oldsigs.dcd_down ? MgslEvent_DcdInactive:0) +
2664                           (newsigs.cts_up   != oldsigs.cts_up   ? MgslEvent_CtsActive:0)   +
2665                           (newsigs.cts_down != oldsigs.cts_down ? MgslEvent_CtsInactive:0) +
2666                           (newsigs.ri_up    != oldsigs.ri_up    ? MgslEvent_RiActive:0)    +
2667                           (newsigs.ri_down  != oldsigs.ri_down  ? MgslEvent_RiInactive:0)  +
2668                           (cnow.exithunt    != cprev.exithunt   ? MgslEvent_ExitHuntMode:0) +
2669                           (cnow.rxidle      != cprev.rxidle     ? MgslEvent_IdleReceived:0) );
2670                 if (events)
2671                         break;
2672
2673                 cprev = cnow;
2674                 oldsigs = newsigs;
2675         }
2676
2677         remove_wait_queue(&info->event_wait_q, &wait);
2678         set_current_state(TASK_RUNNING);
2679
2680
2681         if (mask & (MgslEvent_ExitHuntMode + MgslEvent_IdleReceived)) {
2682                 spin_lock_irqsave(&info->lock,flags);
2683                 if (!waitqueue_active(&info->event_wait_q)) {
2684                         /* disable enable exit hunt mode/idle rcvd IRQs */
2685                         wr_reg16(info, SCR,
2686                                 (unsigned short)(rd_reg16(info, SCR) & ~IRQ_RXIDLE));
2687                 }
2688                 spin_unlock_irqrestore(&info->lock,flags);
2689         }
2690 exit:
2691         if (rc == 0)
2692                 rc = put_user(events, mask_ptr);
2693         return rc;
2694 }
2695
2696 static int get_interface(struct slgt_info *info, int __user *if_mode)
2697 {
2698         DBGINFO(("%s get_interface=%x\n", info->device_name, info->if_mode));
2699         if (put_user(info->if_mode, if_mode))
2700                 return -EFAULT;
2701         return 0;
2702 }
2703
2704 static int set_interface(struct slgt_info *info, int if_mode)
2705 {
2706         unsigned long flags;
2707         unsigned short val;
2708
2709         DBGINFO(("%s set_interface=%x)\n", info->device_name, if_mode));
2710         spin_lock_irqsave(&info->lock,flags);
2711         info->if_mode = if_mode;
2712
2713         msc_set_vcr(info);
2714
2715         /* TCR (tx control) 07  1=RTS driver control */
2716         val = rd_reg16(info, TCR);
2717         if (info->if_mode & MGSL_INTERFACE_RTS_EN)
2718                 val |= BIT7;
2719         else
2720                 val &= ~BIT7;
2721         wr_reg16(info, TCR, val);
2722
2723         spin_unlock_irqrestore(&info->lock,flags);
2724         return 0;
2725 }
2726
2727 /*
2728  * set general purpose IO pin state and direction
2729  *
2730  * user_gpio fields:
2731  * state   each bit indicates a pin state
2732  * smask   set bit indicates pin state to set
2733  * dir     each bit indicates a pin direction (0=input, 1=output)
2734  * dmask   set bit indicates pin direction to set
2735  */
2736 static int set_gpio(struct slgt_info *info, struct gpio_desc __user *user_gpio)
2737 {
2738         unsigned long flags;
2739         struct gpio_desc gpio;
2740         __u32 data;
2741
2742         if (!info->gpio_present)
2743                 return -EINVAL;
2744         if (copy_from_user(&gpio, user_gpio, sizeof(gpio)))
2745                 return -EFAULT;
2746         DBGINFO(("%s set_gpio state=%08x smask=%08x dir=%08x dmask=%08x\n",
2747                  info->device_name, gpio.state, gpio.smask,
2748                  gpio.dir, gpio.dmask));
2749
2750         spin_lock_irqsave(&info->lock,flags);
2751         if (gpio.dmask) {
2752                 data = rd_reg32(info, IODR);
2753                 data |= gpio.dmask & gpio.dir;
2754                 data &= ~(gpio.dmask & ~gpio.dir);
2755                 wr_reg32(info, IODR, data);
2756         }
2757         if (gpio.smask) {
2758                 data = rd_reg32(info, IOVR);
2759                 data |= gpio.smask & gpio.state;
2760                 data &= ~(gpio.smask & ~gpio.state);
2761                 wr_reg32(info, IOVR, data);
2762         }
2763         spin_unlock_irqrestore(&info->lock,flags);
2764
2765         return 0;
2766 }
2767
2768 /*
2769  * get general purpose IO pin state and direction
2770  */
2771 static int get_gpio(struct slgt_info *info, struct gpio_desc __user *user_gpio)
2772 {
2773         struct gpio_desc gpio;
2774         if (!info->gpio_present)
2775                 return -EINVAL;
2776         gpio.state = rd_reg32(info, IOVR);
2777         gpio.smask = 0xffffffff;
2778         gpio.dir   = rd_reg32(info, IODR);
2779         gpio.dmask = 0xffffffff;
2780         if (copy_to_user(user_gpio, &gpio, sizeof(gpio)))
2781                 return -EFAULT;
2782         DBGINFO(("%s get_gpio state=%08x dir=%08x\n",
2783                  info->device_name, gpio.state, gpio.dir));
2784         return 0;
2785 }
2786
2787 /*
2788  * conditional wait facility
2789  */
2790 static void init_cond_wait(struct cond_wait *w, unsigned int data)
2791 {
2792         init_waitqueue_head(&w->q);
2793         init_waitqueue_entry(&w->wait, current);
2794         w->data = data;
2795 }
2796
2797 static void add_cond_wait(struct cond_wait **head, struct cond_wait *w)
2798 {
2799         set_current_state(TASK_INTERRUPTIBLE);
2800         add_wait_queue(&w->q, &w->wait);
2801         w->next = *head;
2802         *head = w;
2803 }
2804
2805 static void remove_cond_wait(struct cond_wait **head, struct cond_wait *cw)
2806 {
2807         struct cond_wait *w, *prev;
2808         remove_wait_queue(&cw->q, &cw->wait);
2809         set_current_state(TASK_RUNNING);
2810         for (w = *head, prev = NULL ; w != NULL ; prev = w, w = w->next) {
2811                 if (w == cw) {
2812                         if (prev != NULL)
2813                                 prev->next = w->next;
2814                         else
2815                                 *head = w->next;
2816                         break;
2817                 }
2818         }
2819 }
2820
2821 static void flush_cond_wait(struct cond_wait **head)
2822 {
2823         while (*head != NULL) {
2824                 wake_up_interruptible(&(*head)->q);
2825                 *head = (*head)->next;
2826         }
2827 }
2828
2829 /*
2830  * wait for general purpose I/O pin(s) to enter specified state
2831  *
2832  * user_gpio fields:
2833  * state - bit indicates target pin state
2834  * smask - set bit indicates watched pin
2835  *
2836  * The wait ends when at least one watched pin enters the specified
2837  * state. When 0 (no error) is returned, user_gpio->state is set to the
2838  * state of all GPIO pins when the wait ends.
2839  *
2840  * Note: Each pin may be a dedicated input, dedicated output, or
2841  * configurable input/output. The number and configuration of pins
2842  * varies with the specific adapter model. Only input pins (dedicated
2843  * or configured) can be monitored with this function.
2844  */
2845 static int wait_gpio(struct slgt_info *info, struct gpio_desc __user *user_gpio)
2846 {
2847         unsigned long flags;
2848         int rc = 0;
2849         struct gpio_desc gpio;
2850         struct cond_wait wait;
2851         u32 state;
2852
2853         if (!info->gpio_present)
2854                 return -EINVAL;
2855         if (copy_from_user(&gpio, user_gpio, sizeof(gpio)))
2856                 return -EFAULT;
2857         DBGINFO(("%s wait_gpio() state=%08x smask=%08x\n",
2858                  info->device_name, gpio.state, gpio.smask));
2859         /* ignore output pins identified by set IODR bit */
2860         if ((gpio.smask &= ~rd_reg32(info, IODR)) == 0)
2861                 return -EINVAL;
2862         init_cond_wait(&wait, gpio.smask);
2863
2864         spin_lock_irqsave(&info->lock, flags);
2865         /* enable interrupts for watched pins */
2866         wr_reg32(info, IOER, rd_reg32(info, IOER) | gpio.smask);
2867         /* get current pin states */
2868         state = rd_reg32(info, IOVR);
2869
2870         if (gpio.smask & ~(state ^ gpio.state)) {
2871                 /* already in target state */
2872                 gpio.state = state;
2873         } else {
2874                 /* wait for target state */
2875                 add_cond_wait(&info->gpio_wait_q, &wait);
2876                 spin_unlock_irqrestore(&info->lock, flags);
2877                 schedule();
2878                 if (signal_pending(current))
2879                         rc = -ERESTARTSYS;
2880                 else
2881                         gpio.state = wait.data;
2882                 spin_lock_irqsave(&info->lock, flags);
2883                 remove_cond_wait(&info->gpio_wait_q, &wait);
2884         }
2885
2886         /* disable all GPIO interrupts if no waiting processes */
2887         if (info->gpio_wait_q == NULL)
2888                 wr_reg32(info, IOER, 0);
2889         spin_unlock_irqrestore(&info->lock,flags);
2890
2891         if ((rc == 0) && copy_to_user(user_gpio, &gpio, sizeof(gpio)))
2892                 rc = -EFAULT;
2893         return rc;
2894 }
2895
2896 static int modem_input_wait(struct slgt_info *info,int arg)
2897 {
2898         unsigned long flags;
2899         int rc;
2900         struct mgsl_icount cprev, cnow;
2901         DECLARE_WAITQUEUE(wait, current);
2902
2903         /* save current irq counts */
2904         spin_lock_irqsave(&info->lock,flags);
2905         cprev = info->icount;
2906         add_wait_queue(&info->status_event_wait_q, &wait);
2907         set_current_state(TASK_INTERRUPTIBLE);
2908         spin_unlock_irqrestore(&info->lock,flags);
2909
2910         for(;;) {
2911                 schedule();
2912                 if (signal_pending(current)) {
2913                         rc = -ERESTARTSYS;
2914                         break;
2915                 }
2916
2917                 /* get new irq counts */
2918                 spin_lock_irqsave(&info->lock,flags);
2919                 cnow = info->icount;
2920                 set_current_state(TASK_INTERRUPTIBLE);
2921                 spin_unlock_irqrestore(&info->lock,flags);
2922
2923                 /* if no change, wait aborted for some reason */
2924                 if (cnow.rng == cprev.rng && cnow.dsr == cprev.dsr &&
2925                     cnow.dcd == cprev.dcd && cnow.cts == cprev.cts) {
2926                         rc = -EIO;
2927                         break;
2928                 }
2929
2930                 /* check for change in caller specified modem input */
2931                 if ((arg & TIOCM_RNG && cnow.rng != cprev.rng) ||
2932                     (arg & TIOCM_DSR && cnow.dsr != cprev.dsr) ||
2933                     (arg & TIOCM_CD  && cnow.dcd != cprev.dcd) ||
2934                     (arg & TIOCM_CTS && cnow.cts != cprev.cts)) {
2935                         rc = 0;
2936                         break;
2937                 }
2938
2939                 cprev = cnow;
2940         }
2941         remove_wait_queue(&info->status_event_wait_q, &wait);
2942         set_current_state(TASK_RUNNING);
2943         return rc;
2944 }
2945
2946 /*
2947  *  return state of serial control and status signals
2948  */
2949 static int tiocmget(struct tty_struct *tty, struct file *file)
2950 {
2951         struct slgt_info *info = tty->driver_data;
2952         unsigned int result;
2953         unsigned long flags;
2954
2955         spin_lock_irqsave(&info->lock,flags);
2956         get_signals(info);
2957         spin_unlock_irqrestore(&info->lock,flags);
2958
2959         result = ((info->signals & SerialSignal_RTS) ? TIOCM_RTS:0) +
2960                 ((info->signals & SerialSignal_DTR) ? TIOCM_DTR:0) +
2961                 ((info->signals & SerialSignal_DCD) ? TIOCM_CAR:0) +
2962                 ((info->signals & SerialSignal_RI)  ? TIOCM_RNG:0) +
2963                 ((info->signals & SerialSignal_DSR) ? TIOCM_DSR:0) +
2964                 ((info->signals & SerialSignal_CTS) ? TIOCM_CTS:0);
2965
2966         DBGINFO(("%s tiocmget value=%08X\n", info->device_name, result));
2967         return result;
2968 }
2969
2970 /*
2971  * set modem control signals (DTR/RTS)
2972  *
2973  *      cmd     signal command: TIOCMBIS = set bit TIOCMBIC = clear bit
2974  *              TIOCMSET = set/clear signal values
2975  *      value   bit mask for command
2976  */
2977 static int tiocmset(struct tty_struct *tty, struct file *file,
2978                     unsigned int set, unsigned int clear)
2979 {
2980         struct slgt_info *info = tty->driver_data;
2981         unsigned long flags;
2982
2983         DBGINFO(("%s tiocmset(%x,%x)\n", info->device_name, set, clear));
2984
2985         if (set & TIOCM_RTS)
2986                 info->signals |= SerialSignal_RTS;
2987         if (set & TIOCM_DTR)
2988                 info->signals |= SerialSignal_DTR;
2989         if (clear & TIOCM_RTS)
2990                 info->signals &= ~SerialSignal_RTS;
2991         if (clear & TIOCM_DTR)
2992                 info->signals &= ~SerialSignal_DTR;
2993
2994         spin_lock_irqsave(&info->lock,flags);
2995         set_signals(info);
2996         spin_unlock_irqrestore(&info->lock,flags);
2997         return 0;
2998 }
2999
3000 /*
3001  *  block current process until the device is ready to open
3002  */
3003 static int block_til_ready(struct tty_struct *tty, struct file *filp,
3004                            struct slgt_info *info)
3005 {
3006         DECLARE_WAITQUEUE(wait, current);
3007         int             retval;
3008         int             do_clocal = 0, extra_count = 0;
3009         unsigned long   flags;
3010
3011         DBGINFO(("%s block_til_ready\n", tty->driver->name));
3012
3013         if (filp->f_flags & O_NONBLOCK || tty->flags & (1 << TTY_IO_ERROR)){
3014                 /* nonblock mode is set or port is not enabled */
3015                 info->flags |= ASYNC_NORMAL_ACTIVE;
3016                 return 0;
3017         }
3018
3019         if (tty->termios->c_cflag & CLOCAL)
3020                 do_clocal = 1;
3021
3022         /* Wait for carrier detect and the line to become
3023          * free (i.e., not in use by the callout).  While we are in
3024          * this loop, info->count is dropped by one, so that
3025          * close() knows when to free things.  We restore it upon
3026          * exit, either normal or abnormal.
3027          */
3028
3029         retval = 0;
3030         add_wait_queue(&info->open_wait, &wait);
3031
3032         spin_lock_irqsave(&info->lock, flags);
3033         if (!tty_hung_up_p(filp)) {
3034                 extra_count = 1;
3035                 info->count--;
3036         }
3037         spin_unlock_irqrestore(&info->lock, flags);
3038         info->blocked_open++;
3039
3040         while (1) {
3041                 if ((tty->termios->c_cflag & CBAUD)) {
3042                         spin_lock_irqsave(&info->lock,flags);
3043                         info->signals |= SerialSignal_RTS + SerialSignal_DTR;
3044                         set_signals(info);
3045                         spin_unlock_irqrestore(&info->lock,flags);
3046                 }
3047
3048                 set_current_state(TASK_INTERRUPTIBLE);
3049
3050                 if (tty_hung_up_p(filp) || !(info->flags & ASYNC_INITIALIZED)){
3051                         retval = (info->flags & ASYNC_HUP_NOTIFY) ?
3052                                         -EAGAIN : -ERESTARTSYS;
3053                         break;
3054                 }
3055
3056                 spin_lock_irqsave(&info->lock,flags);
3057                 get_signals(info);
3058                 spin_unlock_irqrestore(&info->lock,flags);
3059
3060                 if (!(info->flags & ASYNC_CLOSING) &&
3061                     (do_clocal || (info->signals & SerialSignal_DCD)) ) {
3062                         break;
3063                 }
3064
3065                 if (signal_pending(current)) {
3066                         retval = -ERESTARTSYS;
3067                         break;
3068                 }
3069
3070                 DBGINFO(("%s block_til_ready wait\n", tty->driver->name));
3071                 schedule();
3072         }
3073
3074         set_current_state(TASK_RUNNING);
3075         remove_wait_queue(&info->open_wait, &wait);
3076
3077         if (extra_count)
3078                 info->count++;
3079         info->blocked_open--;
3080
3081         if (!retval)
3082                 info->flags |= ASYNC_NORMAL_ACTIVE;
3083
3084         DBGINFO(("%s block_til_ready ready, rc=%d\n", tty->driver->name, retval));
3085         return retval;
3086 }
3087
3088 static int alloc_tmp_rbuf(struct slgt_info *info)
3089 {
3090         info->tmp_rbuf = kmalloc(info->max_frame_size + 5, GFP_KERNEL);
3091         if (info->tmp_rbuf == NULL)
3092                 return -ENOMEM;
3093         return 0;
3094 }
3095
3096 static void free_tmp_rbuf(struct slgt_info *info)
3097 {
3098         kfree(info->tmp_rbuf);
3099         info->tmp_rbuf = NULL;
3100 }
3101
3102 /*
3103  * allocate DMA descriptor lists.
3104  */
3105 static int alloc_desc(struct slgt_info *info)
3106 {
3107         unsigned int i;
3108         unsigned int pbufs;
3109
3110         /* allocate memory to hold descriptor lists */
3111         info->bufs = pci_alloc_consistent(info->pdev, DESC_LIST_SIZE, &info->bufs_dma_addr);
3112         if (info->bufs == NULL)
3113                 return -ENOMEM;
3114
3115         memset(info->bufs, 0, DESC_LIST_SIZE);
3116
3117         info->rbufs = (struct slgt_desc*)info->bufs;
3118         info->tbufs = ((struct slgt_desc*)info->bufs) + info->rbuf_count;
3119
3120         pbufs = (unsigned int)info->bufs_dma_addr;
3121
3122         /*
3123          * Build circular lists of descriptors
3124          */
3125
3126         for (i=0; i < info->rbuf_count; i++) {
3127                 /* physical address of this descriptor */
3128                 info->rbufs[i].pdesc = pbufs + (i * sizeof(struct slgt_desc));
3129
3130                 /* physical address of next descriptor */
3131                 if (i == info->rbuf_count - 1)
3132                         info->rbufs[i].next = cpu_to_le32(pbufs);
3133                 else
3134                         info->rbufs[i].next = cpu_to_le32(pbufs + ((i+1) * sizeof(struct slgt_desc)));
3135                 set_desc_count(info->rbufs[i], DMABUFSIZE);
3136         }
3137
3138         for (i=0; i < info->tbuf_count; i++) {
3139                 /* physical address of this descriptor */
3140                 info->tbufs[i].pdesc = pbufs + ((info->rbuf_count + i) * sizeof(struct slgt_desc));
3141
3142                 /* physical address of next descriptor */
3143                 if (i == info->tbuf_count - 1)
3144                         info->tbufs[i].next = cpu_to_le32(pbufs + info->rbuf_count * sizeof(struct slgt_desc));
3145                 else
3146                         info->tbufs[i].next = cpu_to_le32(pbufs + ((info->rbuf_count + i + 1) * sizeof(struct slgt_desc)));
3147         }
3148
3149         return 0;
3150 }
3151
3152 static void free_desc(struct slgt_info *info)
3153 {
3154         if (info->bufs != NULL) {
3155                 pci_free_consistent(info->pdev, DESC_LIST_SIZE, info->bufs, info->bufs_dma_addr);
3156                 info->bufs  = NULL;
3157                 info->rbufs = NULL;
3158                 info->tbufs = NULL;
3159         }
3160 }
3161
3162 static int alloc_bufs(struct slgt_info *info, struct slgt_desc *bufs, int count)
3163 {
3164         int i;
3165         for (i=0; i < count; i++) {
3166                 if ((bufs[i].buf = pci_alloc_consistent(info->pdev, DMABUFSIZE, &bufs[i].buf_dma_addr)) == NULL)
3167                         return -ENOMEM;
3168                 bufs[i].pbuf  = cpu_to_le32((unsigned int)bufs[i].buf_dma_addr);
3169         }
3170         return 0;
3171 }
3172
3173 static void free_bufs(struct slgt_info *info, struct slgt_desc *bufs, int count)
3174 {
3175         int i;
3176         for (i=0; i < count; i++) {
3177                 if (bufs[i].buf == NULL)
3178                         continue;
3179                 pci_free_consistent(info->pdev, DMABUFSIZE, bufs[i].buf, bufs[i].buf_dma_addr);
3180                 bufs[i].buf = NULL;
3181         }
3182 }
3183
3184 static int alloc_dma_bufs(struct slgt_info *info)
3185 {
3186         info->rbuf_count = 32;
3187         info->tbuf_count = 32;
3188
3189         if (alloc_desc(info) < 0 ||
3190             alloc_bufs(info, info->rbufs, info->rbuf_count) < 0 ||
3191             alloc_bufs(info, info->tbufs, info->tbuf_count) < 0 ||
3192             alloc_tmp_rbuf(info) < 0) {
3193                 DBGERR(("%s DMA buffer alloc fail\n", info->device_name));
3194                 return -ENOMEM;
3195         }
3196         reset_rbufs(info);
3197         return 0;
3198 }
3199
3200 static void free_dma_bufs(struct slgt_info *info)
3201 {
3202         if (info->bufs) {
3203                 free_bufs(info, info->rbufs, info->rbuf_count);
3204                 free_bufs(info, info->tbufs, info->tbuf_count);
3205                 free_desc(info);
3206         }
3207         free_tmp_rbuf(info);
3208 }
3209
3210 static int claim_resources(struct slgt_info *info)
3211 {
3212         if (request_mem_region(info->phys_reg_addr, SLGT_REG_SIZE, "synclink_gt") == NULL) {
3213                 DBGERR(("%s reg addr conflict, addr=%08X\n",
3214                         info->device_name, info->phys_reg_addr));
3215                 info->init_error = DiagStatus_AddressConflict;
3216                 goto errout;
3217         }
3218         else
3219                 info->reg_addr_requested = 1;
3220
3221         info->reg_addr = ioremap(info->phys_reg_addr, SLGT_REG_SIZE);
3222         if (!info->reg_addr) {
3223                 DBGERR(("%s cant map device registers, addr=%08X\n",
3224                         info->device_name, info->phys_reg_addr));
3225                 info->init_error = DiagStatus_CantAssignPciResources;
3226                 goto errout;
3227         }
3228         return 0;
3229
3230 errout:
3231         release_resources(info);
3232         return -ENODEV;
3233 }
3234
3235 static void release_resources(struct slgt_info *info)
3236 {
3237         if (info->irq_requested) {
3238                 free_irq(info->irq_level, info);
3239                 info->irq_requested = 0;
3240         }
3241
3242         if (info->reg_addr_requested) {
3243                 release_mem_region(info->phys_reg_addr, SLGT_REG_SIZE);
3244                 info->reg_addr_requested = 0;
3245         }
3246
3247         if (info->reg_addr) {
3248                 iounmap(info->reg_addr);
3249                 info->reg_addr = NULL;
3250         }
3251 }
3252
3253 /* Add the specified device instance data structure to the
3254  * global linked list of devices and increment the device count.
3255  */
3256 static void add_device(struct slgt_info *info)
3257 {
3258         char *devstr;
3259
3260         info->next_device = NULL;
3261         info->line = slgt_device_count;
3262         sprintf(info->device_name, "%s%d", tty_dev_prefix, info->line);
3263
3264         if (info->line < MAX_DEVICES) {
3265                 if (maxframe[info->line])
3266                         info->max_frame_size = maxframe[info->line];
3267                 info->dosyncppp = dosyncppp[info->line];
3268         }
3269
3270         slgt_device_count++;
3271
3272         if (!slgt_device_list)
3273                 slgt_device_list = info;
3274         else {
3275                 struct slgt_info *current_dev = slgt_device_list;
3276                 while(current_dev->next_device)
3277                         current_dev = current_dev->next_device;
3278                 current_dev->next_device = info;
3279         }
3280
3281         if (info->max_frame_size < 4096)
3282                 info->max_frame_size = 4096;
3283         else if (info->max_frame_size > 65535)
3284                 info->max_frame_size = 65535;
3285
3286         switch(info->pdev->device) {
3287         case SYNCLINK_GT_DEVICE_ID:
3288                 devstr = "GT";
3289                 break;
3290         case SYNCLINK_GT2_DEVICE_ID:
3291                 devstr = "GT2";
3292                 break;
3293         case SYNCLINK_GT4_DEVICE_ID:
3294                 devstr = "GT4";
3295                 break;
3296         case SYNCLINK_AC_DEVICE_ID:
3297                 devstr = "AC";
3298                 info->params.mode = MGSL_MODE_ASYNC;
3299                 break;
3300         default:
3301                 devstr = "(unknown model)";
3302         }
3303         printk("SyncLink %s %s IO=%08x IRQ=%d MaxFrameSize=%u\n",
3304                 devstr, info->device_name, info->phys_reg_addr,
3305                 info->irq_level, info->max_frame_size);
3306
3307 #if SYNCLINK_GENERIC_HDLC
3308         hdlcdev_init(info);
3309 #endif
3310 }
3311
3312 /*
3313  *  allocate device instance structure, return NULL on failure
3314  */
3315 static struct slgt_info *alloc_dev(int adapter_num, int port_num, struct pci_dev *pdev)
3316 {
3317         struct slgt_info *info;
3318
3319         info = kmalloc(sizeof(struct slgt_info), GFP_KERNEL);
3320
3321         if (!info) {
3322                 DBGERR(("%s device alloc failed adapter=%d port=%d\n",
3323                         driver_name, adapter_num, port_num));
3324         } else {
3325                 memset(info, 0, sizeof(struct slgt_info));
3326                 info->magic = MGSL_MAGIC;
3327                 INIT_WORK(&info->task, bh_handler);
3328                 info->max_frame_size = 4096;
3329                 info->raw_rx_size = DMABUFSIZE;
3330                 info->close_delay = 5*HZ/10;
3331                 info->closing_wait = 30*HZ;
3332                 init_waitqueue_head(&info->open_wait);
3333                 init_waitqueue_head(&info->close_wait);
3334                 init_waitqueue_head(&info->status_event_wait_q);
3335                 init_waitqueue_head(&info->event_wait_q);
3336                 spin_lock_init(&info->netlock);
3337                 memcpy(&info->params,&default_params,sizeof(MGSL_PARAMS));
3338                 info->idle_mode = HDLC_TXIDLE_FLAGS;
3339                 info->adapter_num = adapter_num;
3340                 info->port_num = port_num;
3341
3342                 setup_timer(&info->tx_timer, tx_timeout, (unsigned long)info);
3343                 setup_timer(&info->rx_timer, rx_timeout, (unsigned long)info);
3344
3345                 /* Copy configuration info to device instance data */
3346                 info->pdev = pdev;
3347                 info->irq_level = pdev->irq;
3348                 info->phys_reg_addr = pci_resource_start(pdev,0);
3349
3350                 info->bus_type = MGSL_BUS_TYPE_PCI;
3351                 info->irq_flags = IRQF_SHARED;
3352
3353                 info->init_error = -1; /* assume error, set to 0 on successful init */
3354         }
3355
3356         return info;
3357 }
3358
3359 static void device_init(int adapter_num, struct pci_dev *pdev)
3360 {
3361         struct slgt_info *port_array[SLGT_MAX_PORTS];
3362         int i;
3363         int port_count = 1;
3364
3365         if (pdev->device == SYNCLINK_GT2_DEVICE_ID)
3366                 port_count = 2;
3367         else if (pdev->device == SYNCLINK_GT4_DEVICE_ID)
3368                 port_count = 4;
3369
3370         /* allocate device instances for all ports */
3371         for (i=0; i < port_count; ++i) {
3372                 port_array[i] = alloc_dev(adapter_num, i, pdev);
3373                 if (port_array[i] == NULL) {
3374                         for (--i; i >= 0; --i)
3375                                 kfree(port_array[i]);
3376                         return;
3377                 }
3378         }
3379
3380         /* give copy of port_array to all ports and add to device list  */
3381         for (i=0; i < port_count; ++i) {
3382                 memcpy(port_array[i]->port_array, port_array, sizeof(port_array));
3383                 add_device(port_array[i]);
3384                 port_array[i]->port_count = port_count;
3385                 spin_lock_init(&port_array[i]->lock);
3386         }
3387
3388         /* Allocate and claim adapter resources */
3389         if (!claim_resources(port_array[0])) {
3390
3391                 alloc_dma_bufs(port_array[0]);
3392
3393                 /* copy resource information from first port to others */
3394                 for (i = 1; i < port_count; ++i) {
3395                         port_array[i]->lock      = port_array[0]->lock;
3396                         port_array[i]->irq_level = port_array[0]->irq_level;
3397                         port_array[i]->reg_addr  = port_array[0]->reg_addr;
3398                         alloc_dma_bufs(port_array[i]);
3399                 }
3400
3401                 if (request_irq(port_array[0]->irq_level,
3402                                         slgt_interrupt,
3403                                         port_array[0]->irq_flags,
3404                                         port_array[0]->device_name,
3405                                         port_array[0]) < 0) {
3406                         DBGERR(("%s request_irq failed IRQ=%d\n",
3407                                 port_array[0]->device_name,
3408                                 port_array[0]->irq_level));
3409                 } else {
3410                         port_array[0]->irq_requested = 1;
3411                         adapter_test(port_array[0]);
3412                         for (i=1 ; i < port_count ; i++) {
3413                                 port_array[i]->init_error = port_array[0]->init_error;
3414                                 port_array[i]->gpio_present = port_array[0]->gpio_present;
3415                         }
3416                 }
3417         }
3418 }
3419
3420 static int __devinit init_one(struct pci_dev *dev,
3421                               const struct pci_device_id *ent)
3422 {
3423         if (pci_enable_device(dev)) {
3424                 printk("error enabling pci device %p\n", dev);
3425                 return -EIO;
3426         }
3427         pci_set_master(dev);
3428         device_init(slgt_device_count, dev);
3429         return 0;
3430 }
3431
3432 static void __devexit remove_one(struct pci_dev *dev)
3433 {
3434 }
3435
3436 static const struct tty_operations ops = {
3437         .open = open,
3438         .close = close,
3439         .write = write,
3440         .put_char = put_char,
3441         .flush_chars = flush_chars,
3442         .write_room = write_room,
3443         .chars_in_buffer = chars_in_buffer,
3444         .flush_buffer = flush_buffer,
3445         .ioctl = ioctl,
3446         .throttle = throttle,
3447         .unthrottle = unthrottle,
3448         .send_xchar = send_xchar,
3449         .break_ctl = set_break,
3450         .wait_until_sent = wait_until_sent,
3451         .read_proc = read_proc,
3452         .set_termios = set_termios,
3453         .stop = tx_hold,
3454         .start = tx_release,
3455         .hangup = hangup,
3456         .tiocmget = tiocmget,
3457         .tiocmset = tiocmset,
3458 };
3459
3460 static void slgt_cleanup(void)
3461 {
3462         int rc;
3463         struct slgt_info *info;
3464         struct slgt_info *tmp;
3465
3466         printk("unload %s %s\n", driver_name, driver_version);
3467
3468         if (serial_driver) {
3469                 if ((rc = tty_unregister_driver(serial_driver)))
3470                         DBGERR(("tty_unregister_driver error=%d\n", rc));
3471                 put_tty_driver(serial_driver);
3472         }
3473
3474         /* reset devices */
3475         info = slgt_device_list;
3476         while(info) {
3477                 reset_port(info);
3478                 info = info->next_device;
3479         }
3480
3481         /* release devices */
3482         info = slgt_device_list;
3483         while(info) {
3484 #if SYNCLINK_GENERIC_HDLC
3485                 hdlcdev_exit(info);
3486 #endif
3487                 free_dma_bufs(info);
3488                 free_tmp_rbuf(info);
3489                 if (info->port_num == 0)
3490                         release_resources(info);
3491                 tmp = info;
3492                 info = info->next_device;
3493                 kfree(tmp);
3494         }
3495
3496         if (pci_registered)
3497                 pci_unregister_driver(&pci_driver);
3498 }
3499
3500 /*
3501  *  Driver initialization entry point.
3502  */
3503 static int __init slgt_init(void)
3504 {
3505         int rc;
3506
3507         printk("%s %s\n", driver_name, driver_version);
3508
3509         slgt_device_count = 0;
3510         if ((rc = pci_register_driver(&pci_driver)) < 0) {
3511                 printk("%s pci_register_driver error=%d\n", driver_name, rc);
3512                 return rc;
3513         }
3514         pci_registered = 1;
3515
3516         if (!slgt_device_list) {
3517                 printk("%s no devices found\n",driver_name);
3518                 pci_unregister_driver(&pci_driver);
3519                 return -ENODEV;
3520         }
3521
3522         serial_driver = alloc_tty_driver(MAX_DEVICES);
3523         if (!serial_driver) {
3524                 rc = -ENOMEM;
3525                 goto error;
3526         }
3527
3528         /* Initialize the tty_driver structure */
3529
3530         serial_driver->owner = THIS_MODULE;
3531         serial_driver->driver_name = tty_driver_name;
3532         serial_driver->name = tty_dev_prefix;
3533         serial_driver->major = ttymajor;
3534         serial_driver->minor_start = 64;
3535         serial_driver->type = TTY_DRIVER_TYPE_SERIAL;
3536         serial_driver->subtype = SERIAL_TYPE_NORMAL;
3537         serial_driver->init_termios = tty_std_termios;
3538         serial_driver->init_termios.c_cflag =
3539                 B9600 | CS8 | CREAD | HUPCL | CLOCAL;
3540         serial_driver->init_termios.c_ispeed = 9600;
3541         serial_driver->init_termios.c_ospeed = 9600;
3542         serial_driver->flags = TTY_DRIVER_REAL_RAW;
3543         tty_set_operations(serial_driver, &ops);
3544         if ((rc = tty_register_driver(serial_driver)) < 0) {
3545                 DBGERR(("%s can't register serial driver\n", driver_name));
3546                 put_tty_driver(serial_driver);
3547                 serial_driver = NULL;
3548                 goto error;
3549         }
3550
3551         printk("%s %s, tty major#%d\n",
3552                 driver_name, driver_version,
3553                 serial_driver->major);
3554
3555         return 0;
3556
3557 error:
3558         slgt_cleanup();
3559         return rc;
3560 }
3561
3562 static void __exit slgt_exit(void)
3563 {
3564         slgt_cleanup();
3565 }
3566
3567 module_init(slgt_init);
3568 module_exit(slgt_exit);
3569
3570 /*
3571  * register access routines
3572  */
3573
3574 #define CALC_REGADDR() \
3575         unsigned long reg_addr = ((unsigned long)info->reg_addr) + addr; \
3576         if (addr >= 0x80) \
3577                 reg_addr += (info->port_num) * 32;
3578
3579 static __u8 rd_reg8(struct slgt_info *info, unsigned int addr)
3580 {
3581         CALC_REGADDR();
3582         return readb((void __iomem *)reg_addr);
3583 }
3584
3585 static void wr_reg8(struct slgt_info *info, unsigned int addr, __u8 value)
3586 {
3587         CALC_REGADDR();
3588         writeb(value, (void __iomem *)reg_addr);
3589 }
3590
3591 static __u16 rd_reg16(struct slgt_info *info, unsigned int addr)
3592 {
3593         CALC_REGADDR();
3594         return readw((void __iomem *)reg_addr);
3595 }
3596
3597 static void wr_reg16(struct slgt_info *info, unsigned int addr, __u16 value)
3598 {
3599         CALC_REGADDR();
3600         writew(value, (void __iomem *)reg_addr);
3601 }
3602
3603 static __u32 rd_reg32(struct slgt_info *info, unsigned int addr)
3604 {
3605         CALC_REGADDR();
3606         return readl((void __iomem *)reg_addr);
3607 }
3608
3609 static void wr_reg32(struct slgt_info *info, unsigned int addr, __u32 value)
3610 {
3611         CALC_REGADDR();
3612         writel(value, (void __iomem *)reg_addr);
3613 }
3614
3615 static void rdma_reset(struct slgt_info *info)
3616 {
3617         unsigned int i;
3618
3619         /* set reset bit */
3620         wr_reg32(info, RDCSR, BIT1);
3621
3622         /* wait for enable bit cleared */
3623         for(i=0 ; i < 1000 ; i++)
3624                 if (!(rd_reg32(info, RDCSR) & BIT0))
3625                         break;
3626 }
3627
3628 static void tdma_reset(struct slgt_info *info)
3629 {
3630         unsigned int i;
3631
3632         /* set reset bit */
3633         wr_reg32(info, TDCSR, BIT1);
3634
3635         /* wait for enable bit cleared */
3636         for(i=0 ; i < 1000 ; i++)
3637                 if (!(rd_reg32(info, TDCSR) & BIT0))
3638                         break;
3639 }
3640
3641 /*
3642  * enable internal loopback
3643  * TxCLK and RxCLK are generated from BRG
3644  * and TxD is looped back to RxD internally.
3645  */
3646 static void enable_loopback(struct slgt_info *info)
3647 {
3648         /* SCR (serial control) BIT2=looopback enable */
3649         wr_reg16(info, SCR, (unsigned short)(rd_reg16(info, SCR) | BIT2));
3650
3651         if (info->params.mode != MGSL_MODE_ASYNC) {
3652                 /* CCR (clock control)
3653                  * 07..05  tx clock source (010 = BRG)
3654                  * 04..02  rx clock source (010 = BRG)
3655                  * 01      auxclk enable   (0 = disable)
3656                  * 00      BRG enable      (1 = enable)
3657                  *
3658                  * 0100 1001
3659                  */
3660                 wr_reg8(info, CCR, 0x49);
3661
3662                 /* set speed if available, otherwise use default */
3663                 if (info->params.clock_speed)
3664                         set_rate(info, info->params.clock_speed);
3665                 else
3666                         set_rate(info, 3686400);
3667         }
3668 }
3669
3670 /*
3671  *  set baud rate generator to specified rate
3672  */
3673 static void set_rate(struct slgt_info *info, u32 rate)
3674 {
3675         unsigned int div;
3676         static unsigned int osc = 14745600;
3677
3678         /* div = osc/rate - 1
3679          *
3680          * Round div up if osc/rate is not integer to
3681          * force to next slowest rate.
3682          */
3683
3684         if (rate) {
3685                 div = osc/rate;
3686                 if (!(osc % rate) && div)
3687                         div--;
3688                 wr_reg16(info, BDR, (unsigned short)div);
3689         }
3690 }
3691
3692 static void rx_stop(struct slgt_info *info)
3693 {
3694         unsigned short val;
3695
3696         /* disable and reset receiver */
3697         val = rd_reg16(info, RCR) & ~BIT1;          /* clear enable bit */
3698         wr_reg16(info, RCR, (unsigned short)(val | BIT2)); /* set reset bit */
3699         wr_reg16(info, RCR, val);                  /* clear reset bit */
3700
3701         slgt_irq_off(info, IRQ_RXOVER + IRQ_RXDATA + IRQ_RXIDLE);
3702
3703         /* clear pending rx interrupts */
3704         wr_reg16(info, SSR, IRQ_RXIDLE + IRQ_RXOVER);
3705
3706         rdma_reset(info);
3707
3708         info->rx_enabled = 0;
3709         info->rx_restart = 0;
3710 }
3711
3712 static void rx_start(struct slgt_info *info)
3713 {
3714         unsigned short val;
3715
3716         slgt_irq_off(info, IRQ_RXOVER + IRQ_RXDATA);
3717
3718         /* clear pending rx overrun IRQ */
3719         wr_reg16(info, SSR, IRQ_RXOVER);
3720
3721         /* reset and disable receiver */
3722         val = rd_reg16(info, RCR) & ~BIT1; /* clear enable bit */
3723         wr_reg16(info, RCR, (unsigned short)(val | BIT2)); /* set reset bit */
3724         wr_reg16(info, RCR, val);                  /* clear reset bit */
3725
3726         rdma_reset(info);
3727         reset_rbufs(info);
3728
3729         /* set 1st descriptor address */
3730         wr_reg32(info, RDDAR, info->rbufs[0].pdesc);
3731
3732         if (info->params.mode != MGSL_MODE_ASYNC) {
3733                 /* enable rx DMA and DMA interrupt */
3734                 wr_reg32(info, RDCSR, (BIT2 + BIT0));
3735         } else {
3736                 /* enable saving of rx status, rx DMA and DMA interrupt */
3737                 wr_reg32(info, RDCSR, (BIT6 + BIT2 + BIT0));
3738         }
3739
3740         slgt_irq_on(info, IRQ_RXOVER);
3741
3742         /* enable receiver */
3743         wr_reg16(info, RCR, (unsigned short)(rd_reg16(info, RCR) | BIT1));
3744
3745         info->rx_restart = 0;
3746         info->rx_enabled = 1;
3747 }
3748
3749 static void tx_start(struct slgt_info *info)
3750 {
3751         if (!info->tx_enabled) {
3752                 wr_reg16(info, TCR,
3753                          (unsigned short)((rd_reg16(info, TCR) | BIT1) & ~BIT2));
3754                 info->tx_enabled = TRUE;
3755         }
3756
3757         if (info->tx_count) {
3758                 info->drop_rts_on_tx_done = 0;
3759
3760                 if (info->params.mode != MGSL_MODE_ASYNC) {
3761                         if (info->params.flags & HDLC_FLAG_AUTO_RTS) {
3762                                 get_signals(info);
3763                                 if (!(info->signals & SerialSignal_RTS)) {
3764                                         info->signals |= SerialSignal_RTS;
3765                                         set_signals(info);
3766                                         info->drop_rts_on_tx_done = 1;
3767                                 }
3768                         }
3769
3770                         slgt_irq_off(info, IRQ_TXDATA);
3771                         slgt_irq_on(info, IRQ_TXUNDER + IRQ_TXIDLE);
3772                         /* clear tx idle and underrun status bits */
3773                         wr_reg16(info, SSR, (unsigned short)(IRQ_TXIDLE + IRQ_TXUNDER));
3774
3775                         if (!(rd_reg32(info, TDCSR) & BIT0)) {
3776                                 /* tx DMA stopped, restart tx DMA */
3777                                 tdma_reset(info);
3778                                 /* set 1st descriptor address */
3779                                 wr_reg32(info, TDDAR, info->tbufs[info->tbuf_start].pdesc);
3780                                 switch(info->params.mode) {
3781                                 case MGSL_MODE_RAW:
3782                                 case MGSL_MODE_MONOSYNC:
3783                                 case MGSL_MODE_BISYNC:
3784                                         wr_reg32(info, TDCSR, BIT2 + BIT0); /* IRQ + DMA enable */
3785                                         break;
3786                                 default:
3787                                         wr_reg32(info, TDCSR, BIT0); /* DMA enable */
3788                                 }
3789                         }
3790
3791                         if (info->params.mode == MGSL_MODE_HDLC)
3792                                 mod_timer(&info->tx_timer, jiffies +
3793                                                 msecs_to_jiffies(5000));
3794                 } else {
3795                         tdma_reset(info);
3796                         /* set 1st descriptor address */
3797                         wr_reg32(info, TDDAR, info->tbufs[info->tbuf_start].pdesc);
3798
3799                         slgt_irq_off(info, IRQ_TXDATA);
3800                         slgt_irq_on(info, IRQ_TXIDLE);
3801                         /* clear tx idle status bit */
3802                         wr_reg16(info, SSR, IRQ_TXIDLE);
3803
3804                         /* enable tx DMA */
3805                         wr_reg32(info, TDCSR, BIT0);
3806                 }
3807
3808                 info->tx_active = 1;
3809         }
3810 }
3811
3812 static void tx_stop(struct slgt_info *info)
3813 {
3814         unsigned short val;
3815
3816         del_timer(&info->tx_timer);
3817
3818         tdma_reset(info);
3819
3820         /* reset and disable transmitter */
3821         val = rd_reg16(info, TCR) & ~BIT1;          /* clear enable bit */
3822         wr_reg16(info, TCR, (unsigned short)(val | BIT2)); /* set reset bit */
3823
3824         slgt_irq_off(info, IRQ_TXDATA + IRQ_TXIDLE + IRQ_TXUNDER);
3825
3826         /* clear tx idle and underrun status bit */
3827         wr_reg16(info, SSR, (unsigned short)(IRQ_TXIDLE + IRQ_TXUNDER));
3828
3829         reset_tbufs(info);
3830
3831         info->tx_enabled = 0;
3832         info->tx_active  = 0;
3833 }
3834
3835 static void reset_port(struct slgt_info *info)
3836 {
3837         if (!info->reg_addr)
3838                 return;
3839
3840         tx_stop(info);
3841         rx_stop(info);
3842
3843         info->signals &= ~(SerialSignal_DTR + SerialSignal_RTS);
3844         set_signals(info);
3845
3846         slgt_irq_off(info, IRQ_ALL | IRQ_MASTER);
3847 }
3848
3849 static void reset_adapter(struct slgt_info *info)
3850 {
3851         int i;
3852         for (i=0; i < info->port_count; ++i) {
3853                 if (info->port_array[i])
3854                         reset_port(info->port_array[i]);
3855         }
3856 }
3857
3858 static void async_mode(struct slgt_info *info)
3859 {
3860         unsigned short val;
3861
3862         slgt_irq_off(info, IRQ_ALL | IRQ_MASTER);
3863         tx_stop(info);
3864         rx_stop(info);
3865
3866         /* TCR (tx control)
3867          *
3868          * 15..13  mode, 010=async
3869          * 12..10  encoding, 000=NRZ
3870          * 09      parity enable
3871          * 08      1=odd parity, 0=even parity
3872          * 07      1=RTS driver control
3873          * 06      1=break enable
3874          * 05..04  character length
3875          *         00=5 bits
3876          *         01=6 bits
3877          *         10=7 bits
3878          *         11=8 bits
3879          * 03      0=1 stop bit, 1=2 stop bits
3880          * 02      reset
3881          * 01      enable
3882          * 00      auto-CTS enable
3883          */
3884         val = 0x4000;
3885
3886         if (info->if_mode & MGSL_INTERFACE_RTS_EN)
3887                 val |= BIT7;
3888
3889         if (info->params.parity != ASYNC_PARITY_NONE) {
3890                 val |= BIT9;
3891                 if (info->params.parity == ASYNC_PARITY_ODD)
3892                         val |= BIT8;
3893         }
3894
3895         switch (info->params.data_bits)
3896         {
3897         case 6: val |= BIT4; break;
3898         case 7: val |= BIT5; break;
3899         case 8: val |= BIT5 + BIT4; break;
3900         }
3901
3902         if (info->params.stop_bits != 1)
3903                 val |= BIT3;
3904
3905         if (info->params.flags & HDLC_FLAG_AUTO_CTS)
3906                 val |= BIT0;
3907
3908         wr_reg16(info, TCR, val);
3909
3910         /* RCR (rx control)
3911          *
3912          * 15..13  mode, 010=async
3913          * 12..10  encoding, 000=NRZ
3914          * 09      parity enable
3915          * 08      1=odd parity, 0=even parity
3916          * 07..06  reserved, must be 0
3917          * 05..04  character length
3918          *         00=5 bits
3919          *         01=6 bits
3920          *         10=7 bits
3921          *         11=8 bits
3922          * 03      reserved, must be zero
3923          * 02      reset
3924          * 01      enable
3925          * 00      auto-DCD enable
3926          */
3927         val = 0x4000;
3928
3929         if (info->params.parity != ASYNC_PARITY_NONE) {
3930                 val |= BIT9;
3931                 if (info->params.parity == ASYNC_PARITY_ODD)
3932                         val |= BIT8;
3933         }
3934
3935         switch (info->params.data_bits)
3936         {
3937         case 6: val |= BIT4; break;
3938         case 7: val |= BIT5; break;
3939         case 8: val |= BIT5 + BIT4; break;
3940         }
3941
3942         if (info->params.flags & HDLC_FLAG_AUTO_DCD)
3943                 val |= BIT0;
3944
3945         wr_reg16(info, RCR, val);
3946
3947         /* CCR (clock control)
3948          *
3949          * 07..05  011 = tx clock source is BRG/16
3950          * 04..02  010 = rx clock source is BRG
3951          * 01      0 = auxclk disabled
3952          * 00      1 = BRG enabled
3953          *
3954          * 0110 1001
3955          */
3956         wr_reg8(info, CCR, 0x69);
3957
3958         msc_set_vcr(info);
3959
3960         /* SCR (serial control)
3961          *
3962          * 15  1=tx req on FIFO half empty
3963          * 14  1=rx req on FIFO half full
3964          * 13  tx data  IRQ enable
3965          * 12  tx idle  IRQ enable
3966          * 11  rx break on IRQ enable
3967          * 10  rx data  IRQ enable
3968          * 09  rx break off IRQ enable
3969          * 08  overrun  IRQ enable
3970          * 07  DSR      IRQ enable
3971          * 06  CTS      IRQ enable
3972          * 05  DCD      IRQ enable
3973          * 04  RI       IRQ enable
3974          * 03  reserved, must be zero
3975          * 02  1=txd->rxd internal loopback enable
3976          * 01  reserved, must be zero
3977          * 00  1=master IRQ enable
3978          */
3979         val = BIT15 + BIT14 + BIT0;
3980         wr_reg16(info, SCR, val);
3981
3982         slgt_irq_on(info, IRQ_RXBREAK | IRQ_RXOVER);
3983
3984         set_rate(info, info->params.data_rate * 16);
3985
3986         if (info->params.loopback)
3987                 enable_loopback(info);
3988 }
3989
3990 static void sync_mode(struct slgt_info *info)
3991 {
3992         unsigned short val;
3993
3994         slgt_irq_off(info, IRQ_ALL | IRQ_MASTER);
3995         tx_stop(info);
3996         rx_stop(info);
3997
3998         /* TCR (tx control)
3999          *
4000          * 15..13  mode, 000=HDLC 001=raw 010=async 011=monosync 100=bisync
4001          * 12..10  encoding
4002          * 09      CRC enable
4003          * 08      CRC32
4004          * 07      1=RTS driver control
4005          * 06      preamble enable
4006          * 05..04  preamble length
4007          * 03      share open/close flag
4008          * 02      reset
4009          * 01      enable
4010          * 00      auto-CTS enable
4011          */
4012         val = 0;
4013
4014         switch(info->params.mode) {
4015         case MGSL_MODE_MONOSYNC: val |= BIT14 + BIT13; break;
4016         case MGSL_MODE_BISYNC:   val |= BIT15; break;
4017         case MGSL_MODE_RAW:      val |= BIT13; break;
4018         }
4019         if (info->if_mode & MGSL_INTERFACE_RTS_EN)
4020                 val |= BIT7;
4021
4022         switch(info->params.encoding)
4023         {
4024         case HDLC_ENCODING_NRZB:          val |= BIT10; break;
4025         case HDLC_ENCODING_NRZI_MARK:     val |= BIT11; break;
4026         case HDLC_ENCODING_NRZI:          val |= BIT11 + BIT10; break;
4027         case HDLC_ENCODING_BIPHASE_MARK:  val |= BIT12; break;
4028         case HDLC_ENCODING_BIPHASE_SPACE: val |= BIT12 + BIT10; break;
4029         case HDLC_ENCODING_BIPHASE_LEVEL: val |= BIT12 + BIT11; break;
4030         case HDLC_ENCODING_DIFF_BIPHASE_LEVEL: val |= BIT12 + BIT11 + BIT10; break;
4031         }
4032
4033         switch (info->params.crc_type & HDLC_CRC_MASK)
4034         {
4035         case HDLC_CRC_16_CCITT: val |= BIT9; break;
4036         case HDLC_CRC_32_CCITT: val |= BIT9 + BIT8; break;
4037         }
4038
4039         if (info->params.preamble != HDLC_PREAMBLE_PATTERN_NONE)
4040                 val |= BIT6;
4041
4042         switch (info->params.preamble_length)
4043         {
4044         case HDLC_PREAMBLE_LENGTH_16BITS: val |= BIT5; break;
4045         case HDLC_PREAMBLE_LENGTH_32BITS: val |= BIT4; break;
4046         case HDLC_PREAMBLE_LENGTH_64BITS: val |= BIT5 + BIT4; break;
4047         }
4048
4049         if (info->params.flags & HDLC_FLAG_AUTO_CTS)
4050                 val |= BIT0;
4051
4052         wr_reg16(info, TCR, val);
4053
4054         /* TPR (transmit preamble) */
4055
4056         switch (info->params.preamble)
4057         {
4058         case HDLC_PREAMBLE_PATTERN_FLAGS: val = 0x7e; break;
4059         case HDLC_PREAMBLE_PATTERN_ONES:  val = 0xff; break;
4060         case HDLC_PREAMBLE_PATTERN_ZEROS: val = 0x00; break;
4061         case HDLC_PREAMBLE_PATTERN_10:    val = 0x55; break;
4062         case HDLC_PREAMBLE_PATTERN_01:    val = 0xaa; break;
4063         default:                          val = 0x7e; break;
4064         }
4065         wr_reg8(info, TPR, (unsigned char)val);
4066
4067         /* RCR (rx control)
4068          *
4069          * 15..13  mode, 000=HDLC 001=raw 010=async 011=monosync 100=bisync
4070          * 12..10  encoding
4071          * 09      CRC enable
4072          * 08      CRC32
4073          * 07..03  reserved, must be 0
4074          * 02      reset
4075          * 01      enable
4076          * 00      auto-DCD enable
4077          */
4078         val = 0;
4079
4080         switch(info->params.mode) {
4081         case MGSL_MODE_MONOSYNC: val |= BIT14 + BIT13; break;
4082         case MGSL_MODE_BISYNC:   val |= BIT15; break;
4083         case MGSL_MODE_RAW:      val |= BIT13; break;
4084         }
4085
4086         switch(info->params.encoding)
4087         {
4088         case HDLC_ENCODING_NRZB:          val |= BIT10; break;
4089         case HDLC_ENCODING_NRZI_MARK:     val |= BIT11; break;
4090         case HDLC_ENCODING_NRZI:          val |= BIT11 + BIT10; break;
4091         case HDLC_ENCODING_BIPHASE_MARK:  val |= BIT12; break;
4092         case HDLC_ENCODING_BIPHASE_SPACE: val |= BIT12 + BIT10; break;
4093         case HDLC_ENCODING_BIPHASE_LEVEL: val |= BIT12 + BIT11; break;
4094         case HDLC_ENCODING_DIFF_BIPHASE_LEVEL: val |= BIT12 + BIT11 + BIT10; break;
4095         }
4096
4097         switch (info->params.crc_type & HDLC_CRC_MASK)
4098         {
4099         case HDLC_CRC_16_CCITT: val |= BIT9; break;
4100         case HDLC_CRC_32_CCITT: val |= BIT9 + BIT8; break;
4101         }
4102
4103         if (info->params.flags & HDLC_FLAG_AUTO_DCD)
4104                 val |= BIT0;
4105
4106         wr_reg16(info, RCR, val);
4107
4108         /* CCR (clock control)
4109          *
4110          * 07..05  tx clock source
4111          * 04..02  rx clock source
4112          * 01      auxclk enable
4113          * 00      BRG enable
4114          */
4115         val = 0;
4116
4117         if (info->params.flags & HDLC_FLAG_TXC_BRG)
4118         {
4119                 // when RxC source is DPLL, BRG generates 16X DPLL
4120                 // reference clock, so take TxC from BRG/16 to get
4121                 // transmit clock at actual data rate
4122                 if (info->params.flags & HDLC_FLAG_RXC_DPLL)
4123                         val |= BIT6 + BIT5;     /* 011, txclk = BRG/16 */
4124                 else
4125                         val |= BIT6;    /* 010, txclk = BRG */
4126         }
4127         else if (info->params.flags & HDLC_FLAG_TXC_DPLL)
4128                 val |= BIT7;    /* 100, txclk = DPLL Input */
4129         else if (info->params.flags & HDLC_FLAG_TXC_RXCPIN)
4130                 val |= BIT5;    /* 001, txclk = RXC Input */
4131
4132         if (info->params.flags & HDLC_FLAG_RXC_BRG)
4133                 val |= BIT3;    /* 010, rxclk = BRG */
4134         else if (info->params.flags & HDLC_FLAG_RXC_DPLL)
4135                 val |= BIT4;    /* 100, rxclk = DPLL */
4136         else if (info->params.flags & HDLC_FLAG_RXC_TXCPIN)
4137                 val |= BIT2;    /* 001, rxclk = TXC Input */
4138
4139         if (info->params.clock_speed)
4140                 val |= BIT1 + BIT0;
4141
4142         wr_reg8(info, CCR, (unsigned char)val);
4143
4144         if (info->params.flags & (HDLC_FLAG_TXC_DPLL + HDLC_FLAG_RXC_DPLL))
4145         {
4146                 // program DPLL mode
4147                 switch(info->params.encoding)
4148                 {
4149                 case HDLC_ENCODING_BIPHASE_MARK:
4150                 case HDLC_ENCODING_BIPHASE_SPACE:
4151                         val = BIT7; break;
4152                 case HDLC_ENCODING_BIPHASE_LEVEL:
4153                 case HDLC_ENCODING_DIFF_BIPHASE_LEVEL:
4154                         val = BIT7 + BIT6; break;
4155                 default: val = BIT6;    // NRZ encodings
4156                 }
4157                 wr_reg16(info, RCR, (unsigned short)(rd_reg16(info, RCR) | val));
4158
4159                 // DPLL requires a 16X reference clock from BRG
4160                 set_rate(info, info->params.clock_speed * 16);
4161         }
4162         else
4163                 set_rate(info, info->params.clock_speed);
4164
4165         tx_set_idle(info);
4166
4167         msc_set_vcr(info);
4168
4169         /* SCR (serial control)
4170          *
4171          * 15  1=tx req on FIFO half empty
4172          * 14  1=rx req on FIFO half full
4173          * 13  tx data  IRQ enable
4174          * 12  tx idle  IRQ enable
4175          * 11  underrun IRQ enable
4176          * 10  rx data  IRQ enable
4177          * 09  rx idle  IRQ enable
4178          * 08  overrun  IRQ enable
4179          * 07  DSR      IRQ enable
4180          * 06  CTS      IRQ enable
4181          * 05  DCD      IRQ enable
4182          * 04  RI       IRQ enable
4183          * 03  reserved, must be zero
4184          * 02  1=txd->rxd internal loopback enable
4185          * 01  reserved, must be zero
4186          * 00  1=master IRQ enable
4187          */
4188         wr_reg16(info, SCR, BIT15 + BIT14 + BIT0);
4189
4190         if (info->params.loopback)
4191                 enable_loopback(info);
4192 }
4193
4194 /*
4195  *  set transmit idle mode
4196  */
4197 static void tx_set_idle(struct slgt_info *info)
4198 {
4199         unsigned char val;
4200         unsigned short tcr;
4201
4202         /* if preamble enabled (tcr[6] == 1) then tx idle size = 8 bits
4203          * else tcr[5:4] = tx idle size: 00 = 8 bits, 01 = 16 bits
4204          */
4205         tcr = rd_reg16(info, TCR);
4206         if (info->idle_mode & HDLC_TXIDLE_CUSTOM_16) {
4207                 /* disable preamble, set idle size to 16 bits */
4208                 tcr = (tcr & ~(BIT6 + BIT5)) | BIT4;
4209                 /* MSB of 16 bit idle specified in tx preamble register (TPR) */
4210                 wr_reg8(info, TPR, (unsigned char)((info->idle_mode >> 8) & 0xff));
4211         } else if (!(tcr & BIT6)) {
4212                 /* preamble is disabled, set idle size to 8 bits */
4213                 tcr &= ~(BIT5 + BIT4);
4214         }
4215         wr_reg16(info, TCR, tcr);
4216
4217         if (info->idle_mode & (HDLC_TXIDLE_CUSTOM_8 | HDLC_TXIDLE_CUSTOM_16)) {
4218                 /* LSB of custom tx idle specified in tx idle register */
4219                 val = (unsigned char)(info->idle_mode & 0xff);
4220         } else {
4221                 /* standard 8 bit idle patterns */
4222                 switch(info->idle_mode)
4223                 {
4224                 case HDLC_TXIDLE_FLAGS:          val = 0x7e; break;
4225                 case HDLC_TXIDLE_ALT_ZEROS_ONES:
4226                 case HDLC_TXIDLE_ALT_MARK_SPACE: val = 0xaa; break;
4227                 case HDLC_TXIDLE_ZEROS:
4228                 case HDLC_TXIDLE_SPACE:          val = 0x00; break;
4229                 default:                         val = 0xff;
4230                 }
4231         }
4232
4233         wr_reg8(info, TIR, val);
4234 }
4235
4236 /*
4237  * get state of V24 status (input) signals
4238  */
4239 static void get_signals(struct slgt_info *info)
4240 {
4241         unsigned short status = rd_reg16(info, SSR);
4242
4243         /* clear all serial signals except DTR and RTS */
4244         info->signals &= SerialSignal_DTR + SerialSignal_RTS;
4245
4246         if (status & BIT3)
4247                 info->signals |= SerialSignal_DSR;
4248         if (status & BIT2)
4249                 info->signals |= SerialSignal_CTS;
4250         if (status & BIT1)
4251                 info->signals |= SerialSignal_DCD;
4252         if (status & BIT0)
4253                 info->signals |= SerialSignal_RI;
4254 }
4255
4256 /*
4257  * set V.24 Control Register based on current configuration
4258  */
4259 static void msc_set_vcr(struct slgt_info *info)
4260 {
4261         unsigned char val = 0;
4262
4263         /* VCR (V.24 control)
4264          *
4265          * 07..04  serial IF select
4266          * 03      DTR
4267          * 02      RTS
4268          * 01      LL
4269          * 00      RL
4270          */
4271
4272         switch(info->if_mode & MGSL_INTERFACE_MASK)
4273         {
4274         case MGSL_INTERFACE_RS232:
4275                 val |= BIT5; /* 0010 */
4276                 break;
4277         case MGSL_INTERFACE_V35:
4278                 val |= BIT7 + BIT6 + BIT5; /* 1110 */
4279                 break;
4280         case MGSL_INTERFACE_RS422:
4281                 val |= BIT6; /* 0100 */
4282                 break;
4283         }
4284
4285         if (info->signals & SerialSignal_DTR)
4286                 val |= BIT3;
4287         if (info->signals & SerialSignal_RTS)
4288                 val |= BIT2;
4289         if (info->if_mode & MGSL_INTERFACE_LL)
4290                 val |= BIT1;
4291         if (info->if_mode & MGSL_INTERFACE_RL)
4292                 val |= BIT0;
4293         wr_reg8(info, VCR, val);
4294 }
4295
4296 /*
4297  * set state of V24 control (output) signals
4298  */
4299 static void set_signals(struct slgt_info *info)
4300 {
4301         unsigned char val = rd_reg8(info, VCR);
4302         if (info->signals & SerialSignal_DTR)
4303                 val |= BIT3;
4304         else
4305                 val &= ~BIT3;
4306         if (info->signals & SerialSignal_RTS)
4307                 val |= BIT2;
4308         else
4309                 val &= ~BIT2;
4310         wr_reg8(info, VCR, val);
4311 }
4312
4313 /*
4314  * free range of receive DMA buffers (i to last)
4315  */
4316 static void free_rbufs(struct slgt_info *info, unsigned int i, unsigned int last)
4317 {
4318         int done = 0;
4319
4320         while(!done) {
4321                 /* reset current buffer for reuse */
4322                 info->rbufs[i].status = 0;
4323                 switch(info->params.mode) {
4324                 case MGSL_MODE_RAW:
4325                 case MGSL_MODE_MONOSYNC:
4326                 case MGSL_MODE_BISYNC:
4327                         set_desc_count(info->rbufs[i], info->raw_rx_size);
4328                         break;
4329                 default:
4330                         set_desc_count(info->rbufs[i], DMABUFSIZE);
4331                 }
4332
4333                 if (i == last)
4334                         done = 1;
4335                 if (++i == info->rbuf_count)
4336                         i = 0;
4337         }
4338         info->rbuf_current = i;
4339 }
4340
4341 /*
4342  * mark all receive DMA buffers as free
4343  */
4344 static void reset_rbufs(struct slgt_info *info)
4345 {
4346         free_rbufs(info, 0, info->rbuf_count - 1);
4347 }
4348
4349 /*
4350  * pass receive HDLC frame to upper layer
4351  *
4352  * return 1 if frame available, otherwise 0
4353  */
4354 static int rx_get_frame(struct slgt_info *info)
4355 {
4356         unsigned int start, end;
4357         unsigned short status;
4358         unsigned int framesize = 0;
4359         int rc = 0;
4360         unsigned long flags;
4361         struct tty_struct *tty = info->tty;
4362         unsigned char addr_field = 0xff;
4363         unsigned int crc_size = 0;
4364
4365         switch (info->params.crc_type & HDLC_CRC_MASK) {
4366         case HDLC_CRC_16_CCITT: crc_size = 2; break;
4367         case HDLC_CRC_32_CCITT: crc_size = 4; break;
4368         }
4369
4370 check_again:
4371
4372         framesize = 0;
4373         addr_field = 0xff;
4374         start = end = info->rbuf_current;
4375
4376         for (;;) {
4377                 if (!desc_complete(info->rbufs[end]))
4378                         goto cleanup;
4379
4380                 if (framesize == 0 && info->params.addr_filter != 0xff)
4381                         addr_field = info->rbufs[end].buf[0];
4382
4383                 framesize += desc_count(info->rbufs[end]);
4384
4385                 if (desc_eof(info->rbufs[end]))
4386                         break;
4387
4388                 if (++end == info->rbuf_count)
4389                         end = 0;
4390
4391                 if (end == info->rbuf_current) {
4392                         if (info->rx_enabled){
4393                                 spin_lock_irqsave(&info->lock,flags);
4394                                 rx_start(info);
4395                                 spin_unlock_irqrestore(&info->lock,flags);
4396                         }
4397                         goto cleanup;
4398                 }
4399         }
4400
4401         /* status
4402          *
4403          * 15      buffer complete
4404          * 14..06  reserved
4405          * 05..04  residue
4406          * 02      eof (end of frame)
4407          * 01      CRC error
4408          * 00      abort
4409          */
4410         status = desc_status(info->rbufs[end]);
4411
4412         /* ignore CRC bit if not using CRC (bit is undefined) */
4413         if ((info->params.crc_type & HDLC_CRC_MASK) == HDLC_CRC_NONE)
4414                 status &= ~BIT1;
4415
4416         if (framesize == 0 ||
4417                  (addr_field != 0xff && addr_field != info->params.addr_filter)) {
4418                 free_rbufs(info, start, end);
4419                 goto check_again;
4420         }
4421
4422         if (framesize < (2 + crc_size) || status & BIT0) {
4423                 info->icount.rxshort++;
4424                 framesize = 0;
4425         } else if (status & BIT1) {
4426                 info->icount.rxcrc++;
4427                 if (!(info->params.crc_type & HDLC_CRC_RETURN_EX))
4428                         framesize = 0;
4429         }
4430
4431 #if SYNCLINK_GENERIC_HDLC
4432         if (framesize == 0) {
4433                 struct net_device_stats *stats = hdlc_stats(info->netdev);
4434                 stats->rx_errors++;
4435                 stats->rx_frame_errors++;
4436         }
4437 #endif
4438
4439         DBGBH(("%s rx frame status=%04X size=%d\n",
4440                 info->device_name, status, framesize));
4441         DBGDATA(info, info->rbufs[start].buf, min_t(int, framesize, DMABUFSIZE), "rx");
4442
4443         if (framesize) {
4444                 if (!(info->params.crc_type & HDLC_CRC_RETURN_EX)) {
4445                         framesize -= crc_size;
4446                         crc_size = 0;
4447                 }
4448
4449                 if (framesize > info->max_frame_size + crc_size)
4450                         info->icount.rxlong++;
4451                 else {
4452                         /* copy dma buffer(s) to contiguous temp buffer */
4453                         int copy_count = framesize;
4454                         int i = start;
4455                         unsigned char *p = info->tmp_rbuf;
4456                         info->tmp_rbuf_count = framesize;
4457
4458                         info->icount.rxok++;
4459
4460                         while(copy_count) {
4461                                 int partial_count = min(copy_count, DMABUFSIZE);
4462                                 memcpy(p, info->rbufs[i].buf, partial_count);
4463                                 p += partial_count;
4464                                 copy_count -= partial_count;
4465                                 if (++i == info->rbuf_count)
4466                                         i = 0;
4467                         }
4468
4469                         if (info->params.crc_type & HDLC_CRC_RETURN_EX) {
4470                                 *p = (status & BIT1) ? RX_CRC_ERROR : RX_OK;
4471                                 framesize++;
4472                         }
4473
4474 #if SYNCLINK_GENERIC_HDLC
4475                         if (info->netcount)
4476                                 hdlcdev_rx(info,info->tmp_rbuf, framesize);
4477                         else
4478 #endif
4479                                 ldisc_receive_buf(tty, info->tmp_rbuf, info->flag_buf, framesize);
4480                 }
4481         }
4482         free_rbufs(info, start, end);
4483         rc = 1;
4484
4485 cleanup:
4486         return rc;
4487 }
4488
4489 /*
4490  * pass receive buffer (RAW synchronous mode) to tty layer
4491  * return 1 if buffer available, otherwise 0
4492  */
4493 static int rx_get_buf(struct slgt_info *info)
4494 {
4495         unsigned int i = info->rbuf_current;
4496         unsigned int count;
4497
4498         if (!desc_complete(info->rbufs[i]))
4499                 return 0;
4500         count = desc_count(info->rbufs[i]);
4501         switch(info->params.mode) {
4502         case MGSL_MODE_MONOSYNC:
4503         case MGSL_MODE_BISYNC:
4504                 /* ignore residue in byte synchronous modes */
4505                 if (desc_residue(info->rbufs[i]))
4506                         count--;
4507                 break;
4508         }
4509         DBGDATA(info, info->rbufs[i].buf, count, "rx");
4510         DBGINFO(("rx_get_buf size=%d\n", count));
4511         if (count)
4512                 ldisc_receive_buf(info->tty, info->rbufs[i].buf,
4513                                   info->flag_buf, count);
4514         free_rbufs(info, i, i);
4515         return 1;
4516 }
4517
4518 static void reset_tbufs(struct slgt_info *info)
4519 {
4520         unsigned int i;
4521         info->tbuf_current = 0;
4522         for (i=0 ; i < info->tbuf_count ; i++) {
4523                 info->tbufs[i].status = 0;
4524                 info->tbufs[i].count  = 0;
4525         }
4526 }
4527
4528 /*
4529  * return number of free transmit DMA buffers
4530  */
4531 static unsigned int free_tbuf_count(struct slgt_info *info)
4532 {
4533         unsigned int count = 0;
4534         unsigned int i = info->tbuf_current;
4535
4536         do
4537         {
4538                 if (desc_count(info->tbufs[i]))
4539                         break; /* buffer in use */
4540                 ++count;
4541                 if (++i == info->tbuf_count)
4542                         i=0;
4543         } while (i != info->tbuf_current);
4544
4545         /* last buffer with zero count may be in use, assume it is */
4546         if (count)
4547                 --count;
4548
4549         return count;
4550 }
4551
4552 /*
4553  * load transmit DMA buffer(s) with data
4554  */
4555 static void tx_load(struct slgt_info *info, const char *buf, unsigned int size)
4556 {
4557         unsigned short count;
4558         unsigned int i;
4559         struct slgt_desc *d;
4560
4561         if (size == 0)
4562                 return;
4563
4564         DBGDATA(info, buf, size, "tx");
4565
4566         info->tbuf_start = i = info->tbuf_current;
4567
4568         while (size) {
4569                 d = &info->tbufs[i];
4570                 if (++i == info->tbuf_count)
4571                         i = 0;
4572
4573                 count = (unsigned short)((size > DMABUFSIZE) ? DMABUFSIZE : size);
4574                 memcpy(d->buf, buf, count);
4575
4576                 size -= count;
4577                 buf  += count;
4578
4579                 /*
4580                  * set EOF bit for last buffer of HDLC frame or
4581                  * for every buffer in raw mode
4582                  */
4583                 if ((!size && info->params.mode == MGSL_MODE_HDLC) ||
4584                     info->params.mode == MGSL_MODE_RAW)
4585                         set_desc_eof(*d, 1);
4586                 else
4587                         set_desc_eof(*d, 0);
4588
4589                 set_desc_count(*d, count);
4590         }
4591
4592         info->tbuf_current = i;
4593 }
4594
4595 static int register_test(struct slgt_info *info)
4596 {
4597         static unsigned short patterns[] =
4598                 {0x0000, 0xffff, 0xaaaa, 0x5555, 0x6969, 0x9696};
4599         static unsigned int count = sizeof(patterns)/sizeof(patterns[0]);
4600         unsigned int i;
4601         int rc = 0;
4602
4603         for (i=0 ; i < count ; i++) {
4604                 wr_reg16(info, TIR, patterns[i]);
4605                 wr_reg16(info, BDR, patterns[(i+1)%count]);
4606                 if ((rd_reg16(info, TIR) != patterns[i]) ||
4607                     (rd_reg16(info, BDR) != patterns[(i+1)%count])) {
4608                         rc = -ENODEV;
4609                         break;
4610                 }
4611         }
4612         info->gpio_present = (rd_reg32(info, JCR) & BIT5) ? 1 : 0;
4613         info->init_error = rc ? 0 : DiagStatus_AddressFailure;
4614         return rc;
4615 }
4616
4617 static int irq_test(struct slgt_info *info)
4618 {
4619         unsigned long timeout;
4620         unsigned long flags;
4621         struct tty_struct *oldtty = info->tty;
4622         u32 speed = info->params.data_rate;
4623
4624         info->params.data_rate = 921600;
4625         info->tty = NULL;
4626
4627         spin_lock_irqsave(&info->lock, flags);
4628         async_mode(info);
4629         slgt_irq_on(info, IRQ_TXIDLE);
4630
4631         /* enable transmitter */
4632         wr_reg16(info, TCR,
4633                 (unsigned short)(rd_reg16(info, TCR) | BIT1));
4634
4635         /* write one byte and wait for tx idle */
4636         wr_reg16(info, TDR, 0);
4637
4638         /* assume failure */
4639         info->init_error = DiagStatus_IrqFailure;
4640         info->irq_occurred = FALSE;
4641
4642         spin_unlock_irqrestore(&info->lock, flags);
4643
4644         timeout=100;
4645         while(timeout-- && !info->irq_occurred)
4646                 msleep_interruptible(10);
4647
4648         spin_lock_irqsave(&info->lock,flags);
4649         reset_port(info);
4650         spin_unlock_irqrestore(&info->lock,flags);
4651
4652         info->params.data_rate = speed;
4653         info->tty = oldtty;
4654
4655         info->init_error = info->irq_occurred ? 0 : DiagStatus_IrqFailure;
4656         return info->irq_occurred ? 0 : -ENODEV;
4657 }
4658
4659 static int loopback_test_rx(struct slgt_info *info)
4660 {
4661         unsigned char *src, *dest;
4662         int count;
4663
4664         if (desc_complete(info->rbufs[0])) {
4665                 count = desc_count(info->rbufs[0]);
4666                 src   = info->rbufs[0].buf;
4667                 dest  = info->tmp_rbuf;
4668
4669                 for( ; count ; count-=2, src+=2) {
4670                         /* src=data byte (src+1)=status byte */
4671                         if (!(*(src+1) & (BIT9 + BIT8))) {
4672                                 *dest = *src;
4673                                 dest++;
4674                                 info->tmp_rbuf_count++;
4675                         }
4676                 }
4677                 DBGDATA(info, info->tmp_rbuf, info->tmp_rbuf_count, "rx");
4678                 return 1;
4679         }
4680         return 0;
4681 }
4682
4683 static int loopback_test(struct slgt_info *info)
4684 {
4685 #define TESTFRAMESIZE 20
4686
4687         unsigned long timeout;
4688         u16 count = TESTFRAMESIZE;
4689         unsigned char buf[TESTFRAMESIZE];
4690         int rc = -ENODEV;
4691         unsigned long flags;
4692
4693         struct tty_struct *oldtty = info->tty;
4694         MGSL_PARAMS params;
4695
4696         memcpy(&params, &info->params, sizeof(params));
4697
4698         info->params.mode = MGSL_MODE_ASYNC;
4699         info->params.data_rate = 921600;
4700         info->params.loopback = 1;
4701         info->tty = NULL;
4702
4703         /* build and send transmit frame */
4704         for (count = 0; count < TESTFRAMESIZE; ++count)
4705                 buf[count] = (unsigned char)count;
4706
4707         info->tmp_rbuf_count = 0;
4708         memset(info->tmp_rbuf, 0, TESTFRAMESIZE);
4709
4710         /* program hardware for HDLC and enabled receiver */
4711         spin_lock_irqsave(&info->lock,flags);
4712         async_mode(info);
4713         rx_start(info);
4714         info->tx_count = count;
4715         tx_load(info, buf, count);
4716         tx_start(info);
4717         spin_unlock_irqrestore(&info->lock, flags);
4718
4719         /* wait for receive complete */
4720         for (timeout = 100; timeout; --timeout) {
4721                 msleep_interruptible(10);
4722                 if (loopback_test_rx(info)) {
4723                         rc = 0;
4724                         break;
4725                 }
4726         }
4727
4728         /* verify received frame length and contents */
4729         if (!rc && (info->tmp_rbuf_count != count ||
4730                   memcmp(buf, info->tmp_rbuf, count))) {
4731                 rc = -ENODEV;
4732         }
4733
4734         spin_lock_irqsave(&info->lock,flags);
4735         reset_adapter(info);
4736         spin_unlock_irqrestore(&info->lock,flags);
4737
4738         memcpy(&info->params, &params, sizeof(info->params));
4739         info->tty = oldtty;
4740
4741         info->init_error = rc ? DiagStatus_DmaFailure : 0;
4742         return rc;
4743 }
4744
4745 static int adapter_test(struct slgt_info *info)
4746 {
4747         DBGINFO(("testing %s\n", info->device_name));
4748         if (register_test(info) < 0) {
4749                 printk("register test failure %s addr=%08X\n",
4750                         info->device_name, info->phys_reg_addr);
4751         } else if (irq_test(info) < 0) {
4752                 printk("IRQ test failure %s IRQ=%d\n",
4753                         info->device_name, info->irq_level);
4754         } else if (loopback_test(info) < 0) {
4755                 printk("loopback test failure %s\n", info->device_name);
4756         }
4757         return info->init_error;
4758 }
4759
4760 /*
4761  * transmit timeout handler
4762  */
4763 static void tx_timeout(unsigned long context)
4764 {
4765         struct slgt_info *info = (struct slgt_info*)context;
4766         unsigned long flags;
4767
4768         DBGINFO(("%s tx_timeout\n", info->device_name));
4769         if(info->tx_active && info->params.mode == MGSL_MODE_HDLC) {
4770                 info->icount.txtimeout++;
4771         }
4772         spin_lock_irqsave(&info->lock,flags);
4773         info->tx_active = 0;
4774         info->tx_count = 0;
4775         spin_unlock_irqrestore(&info->lock,flags);
4776
4777 #if SYNCLINK_GENERIC_HDLC
4778         if (info->netcount)
4779                 hdlcdev_tx_done(info);
4780         else
4781 #endif
4782                 bh_transmit(info);
4783 }
4784
4785 /*
4786  * receive buffer polling timer
4787  */
4788 static void rx_timeout(unsigned long context)
4789 {
4790         struct slgt_info *info = (struct slgt_info*)context;
4791         unsigned long flags;
4792
4793         DBGINFO(("%s rx_timeout\n", info->device_name));
4794         spin_lock_irqsave(&info->lock, flags);
4795         info->pending_bh |= BH_RECEIVE;
4796         spin_unlock_irqrestore(&info->lock, flags);
4797         bh_handler(&info->task);
4798 }
4799