[TG3]: Add firmware version info

[linux-2.6] / drivers / net / irda / vlsi_ir.h

/*********************************************************************
 *
 *      vlsi_ir.h:      VLSI82C147 PCI IrDA controller driver for Linux
 *
 *      Version:        0.5
 *
 *      Copyright (c) 2001-2003 Martin Diehl
 *
 *      This program is free software; you can redistribute it and/or 
 *      modify it under the terms of the GNU General Public License as 
 *      published by the Free Software Foundation; either version 2 of 
 *      the License, or (at your option) any later version.
 *
 *      This program is distributed in the hope that it will be useful,
 *      but WITHOUT ANY WARRANTY; without even the implied warranty of
 *      MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
 *      GNU General Public License for more details.
 *
 *      You should have received a copy of the GNU General Public License 
 *      along with this program; if not, write to the Free Software 
 *      Foundation, Inc., 59 Temple Place, Suite 330, Boston, 
 *      MA 02111-1307 USA
 *
 ********************************************************************/

#ifndef IRDA_VLSI_FIR_H
#define IRDA_VLSI_FIR_H

/* ================================================================
 * compatibility stuff
 */

/* definitions not present in pci_ids.h */

#ifndef PCI_CLASS_WIRELESS_IRDA
#define PCI_CLASS_WIRELESS_IRDA         0x0d00
#endif

#ifndef PCI_CLASS_SUBCLASS_MASK
#define PCI_CLASS_SUBCLASS_MASK         0xffff
#endif

/* in recent 2.5 interrupt handlers have non-void return value */
#ifndef IRQ_RETVAL
typedef void irqreturn_t;
#define IRQ_NONE
#define IRQ_HANDLED
#define IRQ_RETVAL(x)
#endif

/* some stuff need to check kernelversion. Not all 2.5 stuff was present
 * in early 2.5.x - the test is merely to separate 2.4 from 2.5
 */
#include <linux/version.h>

#if LINUX_VERSION_CODE < KERNEL_VERSION(2,5,0)

/* PDE() introduced in 2.5.4 */
#ifdef CONFIG_PROC_FS
#define PDE(inode) ((inode)->u.generic_ip)
#endif

/* irda crc16 calculation exported in 2.5.42 */
#define irda_calc_crc16(fcs,buf,len)    (GOOD_FCS)

/* we use this for unified pci device name access */
#define PCIDEV_NAME(pdev)       ((pdev)->name)

#else /* 2.5 or later */

/* whatever we get from the associated struct device - bus:slot:dev.fn id */
#define PCIDEV_NAME(pdev)       (pci_name(pdev))

#endif

/* ================================================================ */

/* non-standard PCI registers */

enum vlsi_pci_regs {
        VLSI_PCI_CLKCTL         = 0x40,         /* chip clock input control */
        VLSI_PCI_MSTRPAGE       = 0x41,         /* addr [31:24] for all busmaster cycles */
        VLSI_PCI_IRMISC         = 0x42          /* mainly legacy UART related */
};

/* ------------------------------------------ */

/* VLSI_PCI_CLKCTL: Clock Control Register (u8, rw) */

/* Three possible clock sources: either on-chip 48MHz PLL or
 * external clock applied to EXTCLK pin. External clock may
 * be either 48MHz or 40MHz, which is indicated by XCKSEL.
 * CLKSTP controls whether the selected clock source gets
 * connected to the IrDA block.
 *
 * On my HP OB-800 the BIOS sets external 40MHz clock as source
 * when IrDA enabled and I've never detected any PLL lock success.
 * Apparently the 14.3...MHz OSC input required for the PLL to work
 * is not connected and the 40MHz EXTCLK is provided externally.
 * At least this is what makes the driver working for me.
 */

enum vlsi_pci_clkctl {

        /* PLL control */

        CLKCTL_PD_INV           = 0x04,         /* PD#: inverted power down signal,
                                                 * i.e. PLL is powered, if PD_INV set */
        CLKCTL_LOCK             = 0x40,         /* (ro) set, if PLL is locked */

        /* clock source selection */

        CLKCTL_EXTCLK           = 0x20,         /* set to select external clock input, not PLL */
        CLKCTL_XCKSEL           = 0x10,         /* set to indicate EXTCLK is 40MHz, not 48MHz */

        /* IrDA block control */

        CLKCTL_CLKSTP           = 0x80,         /* set to disconnect from selected clock source */
        CLKCTL_WAKE             = 0x08          /* set to enable wakeup feature: whenever IR activity
                                                 * is detected, PD_INV gets set(?) and CLKSTP cleared */
};

/* ------------------------------------------ */

/* VLSI_PCI_MSTRPAGE: Master Page Register (u8, rw) and busmastering stuff */

#define DMA_MASK_USED_BY_HW     0xffffffff
#define DMA_MASK_MSTRPAGE       0x00ffffff
#define MSTRPAGE_VALUE          (DMA_MASK_MSTRPAGE >> 24)

        /* PCI busmastering is somewhat special for this guy - in short:
         *
         * We select to operate using fixed MSTRPAGE=0, use ISA DMA
         * address restrictions to make the PCI BM api aware of this,
         * but ensure the hardware is dealing with real 32bit access.
         *
         * In detail:
         * The chip executes normal 32bit busmaster cycles, i.e.
         * drives all 32 address lines. These addresses however are
         * composed of [0:23] taken from various busaddr-pointers
         * and [24:31] taken from the MSTRPAGE register in the VLSI82C147
         * config space. Therefore _all_ busmastering must be
         * targeted to/from one single 16MB (busaddr-) superpage!
         * The point is to make sure all the allocations for memory
         * locations with busmaster access (ring descriptors, buffers)
         * are indeed bus-mappable to the same 16MB range (for x86 this
         * means they must reside in the same 16MB physical memory address
         * range). The only constraint we have which supports "several objects
         * mappable to common 16MB range" paradigma, is the old ISA DMA
         * restriction to the first 16MB of physical address range.
         * Hence the approach here is to enable PCI busmaster support using
         * the correct 32bit dma-mask used by the chip. Afterwards the device's
         * dma-mask gets restricted to 24bit, which must be honoured somehow by
         * all allocations for memory areas to be exposed to the chip ...
         *
         * Note:
         * Don't be surprised to get "Setting latency timer..." messages every
         * time when PCI busmastering is enabled for the chip.
         * The chip has its PCI latency timer RO fixed at 0 - which is not a
         * problem here, because it is never requesting _burst_ transactions.
         */

/* ------------------------------------------ */

/* VLSI_PCIIRMISC: IR Miscellaneous Register (u8, rw) */

/* legacy UART emulation - not used by this driver - would require:
 * (see below for some register-value definitions)
 *
 *      - IRMISC_UARTEN must be set to enable UART address decoding
 *      - IRMISC_UARTSEL configured
 *      - IRCFG_MASTER must be cleared
 *      - IRCFG_SIR must be set
 *      - IRENABLE_PHYANDCLOCK must be asserted 0->1 (and hence IRENABLE_SIR_ON)
 */

enum vlsi_pci_irmisc {

        /* IR transceiver control */

        IRMISC_IRRAIL           = 0x40,         /* (ro?) IR rail power indication (and control?)
                                                 * 0=3.3V / 1=5V. Probably set during power-on?
                                                 * unclear - not touched by driver */
        IRMISC_IRPD             = 0x08,         /* transceiver power down, if set */

        /* legacy UART control */

        IRMISC_UARTTST          = 0x80,         /* UART test mode - "always write 0" */
        IRMISC_UARTEN           = 0x04,         /* enable UART address decoding */

        /* bits [1:0] IRMISC_UARTSEL to select legacy UART address */

        IRMISC_UARTSEL_3f8      = 0x00,
        IRMISC_UARTSEL_2f8      = 0x01,
        IRMISC_UARTSEL_3e8      = 0x02,
        IRMISC_UARTSEL_2e8      = 0x03
};

/* ================================================================ */

/* registers mapped to 32 byte PCI IO space */

/* note: better access all registers at the indicated u8/u16 size
 *       although some of them contain only 1 byte of information.
 *       some of them (particaluarly PROMPT and IRCFG) ignore
 *       access when using the wrong addressing mode!
 */

enum vlsi_pio_regs {
        VLSI_PIO_IRINTR         = 0x00,         /* interrupt enable/request (u8, rw) */
        VLSI_PIO_RINGPTR        = 0x02,         /* rx/tx ring pointer (u16, ro) */
        VLSI_PIO_RINGBASE       = 0x04,         /* [23:10] of ring address (u16, rw) */
        VLSI_PIO_RINGSIZE       = 0x06,         /* rx/tx ring size (u16, rw) */
        VLSI_PIO_PROMPT         = 0x08,         /* triggers ring processing (u16, wo) */
        /* 0x0a-0x0f: reserved / duplicated UART regs */
        VLSI_PIO_IRCFG          = 0x10,         /* configuration select (u16, rw) */
        VLSI_PIO_SIRFLAG        = 0x12,         /* BOF/EOF for filtered SIR (u16, ro) */
        VLSI_PIO_IRENABLE       = 0x14,         /* enable and status register (u16, rw/ro) */
        VLSI_PIO_PHYCTL         = 0x16,         /* physical layer current status (u16, ro) */
        VLSI_PIO_NPHYCTL        = 0x18,         /* next physical layer select (u16, rw) */
        VLSI_PIO_MAXPKT         = 0x1a,         /* [11:0] max len for packet receive (u16, rw) */
        VLSI_PIO_RCVBCNT        = 0x1c          /* current receive-FIFO byte count (u16, ro) */
        /* 0x1e-0x1f: reserved / duplicated UART regs */
};

/* ------------------------------------------ */

/* VLSI_PIO_IRINTR: Interrupt Register (u8, rw) */

/* enable-bits:
 *              1 = enable / 0 = disable
 * interrupt condition bits:
 *              set according to corresponding interrupt source
 *              (regardless of the state of the enable bits)
 *              enable bit status indicates whether interrupt gets raised
 *              write-to-clear
 * note: RPKTINT and TPKTINT behave different in legacy UART mode (which we don't use :-)
 */

enum vlsi_pio_irintr {
        IRINTR_ACTEN    = 0x80, /* activity interrupt enable */
        IRINTR_ACTIVITY = 0x40, /* activity monitor (traffic detected) */
        IRINTR_RPKTEN   = 0x20, /* receive packet interrupt enable*/
        IRINTR_RPKTINT  = 0x10, /* rx-packet transfered from fifo to memory finished */
        IRINTR_TPKTEN   = 0x08, /* transmit packet interrupt enable */
        IRINTR_TPKTINT  = 0x04, /* last bit of tx-packet+crc shifted to ir-pulser */
        IRINTR_OE_EN    = 0x02, /* UART rx fifo overrun error interrupt enable */
        IRINTR_OE_INT   = 0x01  /* UART rx fifo overrun error (read LSR to clear) */
};

/* we use this mask to check whether the (shared PCI) interrupt is ours */

#define IRINTR_INT_MASK         (IRINTR_ACTIVITY|IRINTR_RPKTINT|IRINTR_TPKTINT)

/* ------------------------------------------ */

/* VLSI_PIO_RINGPTR: Ring Pointer Read-Back Register (u16, ro) */

/* _both_ ring pointers are indices relative to the _entire_ rx,tx-ring!
 * i.e. the referenced descriptor is located
 * at RINGBASE + PTR * sizeof(descr) for rx and tx
 * therefore, the tx-pointer has offset MAX_RING_DESCR
 */

#define MAX_RING_DESCR          64      /* tx, rx rings may contain up to 64 descr each */

#define RINGPTR_RX_MASK         (MAX_RING_DESCR-1)
#define RINGPTR_TX_MASK         ((MAX_RING_DESCR-1)<<8)

#define RINGPTR_GET_RX(p)       ((p)&RINGPTR_RX_MASK)
#define RINGPTR_GET_TX(p)       (((p)&RINGPTR_TX_MASK)>>8)

/* ------------------------------------------ */

/* VLSI_PIO_RINGBASE: Ring Pointer Base Address Register (u16, ro) */

/* Contains [23:10] part of the ring base (bus-) address
 * which must be 1k-alinged. [31:24] is taken from
 * VLSI_PCI_MSTRPAGE above.
 * The controller initiates non-burst PCI BM cycles to
 * fetch and update the descriptors in the ring.
 * Once fetched, the descriptor remains cached onchip
 * until it gets closed and updated due to the ring
 * processing state machine.
 * The entire ring area is split in rx and tx areas with each
 * area consisting of 64 descriptors of 8 bytes each.
 * The rx(tx) ring is located at ringbase+0 (ringbase+64*8).
 */

#define BUS_TO_RINGBASE(p)      (((p)>>10)&0x3fff)

/* ------------------------------------------ */

/* VLSI_PIO_RINGSIZE: Ring Size Register (u16, rw) */

/* bit mask to indicate the ring size to be used for rx and tx.
 *      possible values         encoded bits
 *               4                 0000
 *               8                 0001
 *              16                 0011
 *              32                 0111
 *              64                 1111
 * located at [15:12] for tx and [11:8] for rx ([7:0] unused)
 *
 * note: probably a good idea to have IRCFG_MSTR cleared when writing
 *       this so the state machines are stopped and the RINGPTR is reset!
 */

#define SIZE_TO_BITS(num)               ((((num)-1)>>2)&0x0f)
#define TX_RX_TO_RINGSIZE(tx,rx)        ((SIZE_TO_BITS(tx)<<12)|(SIZE_TO_BITS(rx)<<8))
#define RINGSIZE_TO_RXSIZE(rs)          ((((rs)&0x0f00)>>6)+4)
#define RINGSIZE_TO_TXSIZE(rs)          ((((rs)&0xf000)>>10)+4)


/* ------------------------------------------ */

/* VLSI_PIO_PROMPT: Ring Prompting Register (u16, write-to-start) */

/* writing any value kicks the ring processing state machines
 * for both tx, rx rings as follows:
 *      - active rings (currently owning an active descriptor)
 *        ignore the prompt and continue
 *      - idle rings fetch the next descr from the ring and start
 *        their processing
 */

/* ------------------------------------------ */

/* VLSI_PIO_IRCFG: IR Config Register (u16, rw) */

/* notes:
 *      - not more than one SIR/MIR/FIR bit must be set at any time
 *      - SIR, MIR, FIR and CRC16 select the configuration which will
 *        be applied on next 0->1 transition of IRENABLE_PHYANDCLOCK (see below).
 *      - besides allowing the PCI interface to execute busmaster cycles
 *        and therefore the ring SM to operate, the MSTR bit has side-effects:
 *        when MSTR is cleared, the RINGPTR's get reset and the legacy UART mode
 *        (in contrast to busmaster access mode) gets enabled.
 *      - clearing ENRX or setting ENTX while data is received may stall the
 *        receive fifo until ENRX reenabled _and_ another packet arrives
 *      - SIRFILT means the chip performs the required unwrapping of hardware
 *        headers (XBOF's, BOF/EOF) and un-escaping in the _receive_ direction.
 *        Only the resulting IrLAP payload is copied to the receive buffers -
 *        but with the 16bit FCS still encluded. Question remains, whether it
 *        was already checked or we should do it before passing the packet to IrLAP?
 */

enum vlsi_pio_ircfg {
        IRCFG_LOOP      = 0x4000,       /* enable loopback test mode */
        IRCFG_ENTX      = 0x1000,       /* transmit enable */
        IRCFG_ENRX      = 0x0800,       /* receive enable */
        IRCFG_MSTR      = 0x0400,       /* master enable */
        IRCFG_RXANY     = 0x0200,       /* receive any packet */
        IRCFG_CRC16     = 0x0080,       /* 16bit (not 32bit) CRC select for MIR/FIR */
        IRCFG_FIR       = 0x0040,       /* FIR 4PPM encoding mode enable */
        IRCFG_MIR       = 0x0020,       /* MIR HDLC encoding mode enable */
        IRCFG_SIR       = 0x0010,       /* SIR encoding mode enable */
        IRCFG_SIRFILT   = 0x0008,       /* enable SIR decode filter (receiver unwrapping) */
        IRCFG_SIRTEST   = 0x0004,       /* allow SIR decode filter when not in SIR mode */
        IRCFG_TXPOL     = 0x0002,       /* invert tx polarity when set */
        IRCFG_RXPOL     = 0x0001        /* invert rx polarity when set */
};

/* ------------------------------------------ */

/* VLSI_PIO_SIRFLAG: SIR Flag Register (u16, ro) */

/* register contains hardcoded BOF=0xc0 at [7:0] and EOF=0xc1 at [15:8]
 * which is used for unwrapping received frames in SIR decode-filter mode
 */

/* ------------------------------------------ */

/* VLSI_PIO_IRENABLE: IR Enable Register (u16, rw/ro) */

/* notes:
 *      - IREN acts as gate for latching the configured IR mode information
 *        from IRCFG and IRPHYCTL when IREN=reset and applying them when
 *        IREN gets set afterwards.
 *      - ENTXST reflects IRCFG_ENTX
 *      - ENRXST = IRCFG_ENRX && (!IRCFG_ENTX || IRCFG_LOOP)
 */

enum vlsi_pio_irenable {
        IRENABLE_PHYANDCLOCK    = 0x8000,  /* enable IR phy and gate the mode config (rw) */
        IRENABLE_CFGER          = 0x4000,  /* mode configuration error (ro) */
        IRENABLE_FIR_ON         = 0x2000,  /* FIR on status (ro) */
        IRENABLE_MIR_ON         = 0x1000,  /* MIR on status (ro) */
        IRENABLE_SIR_ON         = 0x0800,  /* SIR on status (ro) */
        IRENABLE_ENTXST         = 0x0400,  /* transmit enable status (ro) */
        IRENABLE_ENRXST         = 0x0200,  /* Receive enable status (ro) */
        IRENABLE_CRC16_ON       = 0x0100   /* 16bit (not 32bit) CRC enabled status (ro) */
};

#define   IRENABLE_MASK     0xff00  /* Read mask */

/* ------------------------------------------ */

/* VLSI_PIO_PHYCTL: IR Physical Layer Current Control Register (u16, ro) */

/* read-back of the currently applied physical layer status.
 * applied from VLSI_PIO_NPHYCTL at rising edge of IRENABLE_PHYANDCLOCK
 * contents identical to VLSI_PIO_NPHYCTL (see below)
 */

/* ------------------------------------------ */

/* VLSI_PIO_NPHYCTL: IR Physical Layer Next Control Register (u16, rw) */

/* latched during IRENABLE_PHYANDCLOCK=0 and applied at 0-1 transition
 *
 * consists of BAUD[15:10], PLSWID[9:5] and PREAMB[4:0] bits defined as follows:
 *
 * SIR-mode:    BAUD = (115.2kHz / baudrate) - 1
 *              PLSWID = (pulsetime * freq / (BAUD+1)) - 1
 *                      where pulsetime is the requested IrPHY pulse width
 *                      and freq is 8(16)MHz for 40(48)MHz primary input clock
 *              PREAMB: don't care for SIR
 *
 *              The nominal SIR pulse width is 3/16 bit time so we have PLSWID=12
 *              fixed for all SIR speeds at 40MHz input clock (PLSWID=24 at 48MHz).
 *              IrPHY also allows shorter pulses down to the nominal pulse duration
 *              at 115.2kbaud (minus some tolerance) which is 1.41 usec.
 *              Using the expression PLSWID = 12/(BAUD+1)-1 (multiplied by two for 48MHz)
 *              we get the minimum acceptable PLSWID values according to the VLSI
 *              specification, which provides 1.5 usec pulse width for all speeds (except
 *              for 2.4kbaud getting 6usec). This is fine with IrPHY v1.3 specs and
 *              reduces the transceiver power which drains the battery. At 9.6kbaud for
 *              example this amounts to more than 90% battery power saving!
 *
 * MIR-mode:    BAUD = 0
 *              PLSWID = 9(10) for 40(48) MHz input clock
 *                      to get nominal MIR pulse width
 *              PREAMB = 1
 *
 * FIR-mode:    BAUD = 0
 *              PLSWID: don't care
 *              PREAMB = 15
 */

#define PHYCTL_BAUD_SHIFT       10
#define PHYCTL_BAUD_MASK        0xfc00
#define PHYCTL_PLSWID_SHIFT     5
#define PHYCTL_PLSWID_MASK      0x03e0
#define PHYCTL_PREAMB_SHIFT     0
#define PHYCTL_PREAMB_MASK      0x001f

#define PHYCTL_TO_BAUD(bwp)     (((bwp)&PHYCTL_BAUD_MASK)>>PHYCTL_BAUD_SHIFT)
#define PHYCTL_TO_PLSWID(bwp)   (((bwp)&PHYCTL_PLSWID_MASK)>>PHYCTL_PLSWID_SHIFT)
#define PHYCTL_TO_PREAMB(bwp)   (((bwp)&PHYCTL_PREAMB_MASK)>>PHYCTL_PREAMB_SHIFT)

#define BWP_TO_PHYCTL(b,w,p)    ((((b)<<PHYCTL_BAUD_SHIFT)&PHYCTL_BAUD_MASK) \
                                 | (((w)<<PHYCTL_PLSWID_SHIFT)&PHYCTL_PLSWID_MASK) \
                                 | (((p)<<PHYCTL_PREAMB_SHIFT)&PHYCTL_PREAMB_MASK))

#define BAUD_BITS(br)           ((115200/(br))-1)

static inline unsigned
calc_width_bits(unsigned baudrate, unsigned widthselect, unsigned clockselect)
{
        unsigned        tmp;

        if (widthselect)        /* nominal 3/16 puls width */
                return (clockselect) ? 12 : 24;

        tmp = ((clockselect) ? 12 : 24) / (BAUD_BITS(baudrate)+1);

        /* intermediate result of integer division needed here */

        return (tmp>0) ? (tmp-1) : 0;
}

#define PHYCTL_SIR(br,ws,cs)    BWP_TO_PHYCTL(BAUD_BITS(br),calc_width_bits((br),(ws),(cs)),0)
#define PHYCTL_MIR(cs)          BWP_TO_PHYCTL(0,((cs)?9:10),1)
#define PHYCTL_FIR              BWP_TO_PHYCTL(0,0,15)

/* quite ugly, I know. But implementing these calculations here avoids
 * having magic numbers in the code and allows some playing with pulsewidths
 * without risk to violate the standards.
 * FWIW, here is the table for reference:
 *
 * baudrate     BAUD    min-PLSWID      nom-PLSWID      PREAMB
 *     2400       47       0(0)            12(24)          0
 *     9600       11       0(0)            12(24)          0
 *    19200        5       1(2)            12(24)          0
 *    38400        2       3(6)            12(24)          0
 *    57600        1       5(10)           12(24)          0
 *   115200        0      11(22)           12(24)          0
 *      MIR        0        -               9(10)          1
 *      FIR        0        -               0             15
 *
 * note: x(y) means x-value for 40MHz / y-value for 48MHz primary input clock
 */

/* ------------------------------------------ */


/* VLSI_PIO_MAXPKT: Maximum Packet Length register (u16, rw) */

/* maximum acceptable length for received packets */

/* hw imposed limitation - register uses only [11:0] */
#define MAX_PACKET_LENGTH       0x0fff

/* IrLAP I-field (apparently not defined elsewhere) */
#define IRDA_MTU                2048

/* complete packet consists of A(1)+C(1)+I(<=IRDA_MTU) */
#define IRLAP_SKB_ALLOCSIZE     (1+1+IRDA_MTU)

/* the buffers we use to exchange frames with the hardware need to be
 * larger than IRLAP_SKB_ALLOCSIZE because we may have up to 4 bytes FCS
 * appended and, in SIR mode, a lot of frame wrapping bytes. The worst
 * case appears to be a SIR packet with I-size==IRDA_MTU and all bytes
 * requiring to be escaped to provide transparency. Furthermore, the peer
 * might ask for quite a number of additional XBOFs:
 *      up to 115+48 XBOFS               163
 *      regular BOF                        1
 *      A-field                            1
 *      C-field                            1
 *      I-field, IRDA_MTU, all escaped  4096
 *      FCS (16 bit at SIR, escaped)       4
 *      EOF                                1
 * AFAICS nothing in IrLAP guarantees A/C field not to need escaping
 * (f.e. 0xc0/0xc1 - i.e. BOF/EOF - are legal values there) so in the
 * worst case we have 4269 bytes total frame size.
 * However, the VLSI uses 12 bits only for all buffer length values,
 * which limits the maximum useable buffer size <= 4095.
 * Note this is not a limitation in the receive case because we use
 * the SIR filtering mode where the hw unwraps the frame and only the
 * bare packet+fcs is stored into the buffer - in contrast to the SIR
 * tx case where we have to pass frame-wrapped packets to the hw.
 * If this would ever become an issue in real life, the only workaround
 * I see would be using the legacy UART emulation in SIR mode.
 */

#define XFER_BUF_SIZE           MAX_PACKET_LENGTH

/* ------------------------------------------ */

/* VLSI_PIO_RCVBCNT: Receive Byte Count Register (u16, ro) */

/* receive packet counter gets incremented on every non-filtered
 * byte which was put in the receive fifo and reset for each
 * new packet. Used to decide whether we are just in the middle
 * of receiving
 */

/* better apply the [11:0] mask when reading, as some docs say the
 * reserved [15:12] would return 1 when reading - which is wrong AFAICS
 */
#define RCVBCNT_MASK    0x0fff

/******************************************************************/

/* descriptors for rx/tx ring
 *
 * accessed by hardware - don't change!
 *
 * the descriptor is owned by hardware, when the ACTIVE status bit
 * is set and nothing (besides reading status to test the bit)
 * shall be done. The bit gets cleared by hw, when the descriptor
 * gets closed. Premature reaping of descriptors owned be the chip
 * can be achieved by disabling IRCFG_MSTR
 *
 * Attention: Writing addr overwrites status!
 *
 * ### FIXME: depends on endianess (but there ain't no non-i586 ob800 ;-)
 */

struct ring_descr_hw {
        volatile u16    rd_count;       /* tx/rx count [11:0] */
        u16             reserved;
        union {
                u32     addr;           /* [23:0] of the buffer's busaddress */
                struct {
                        u8              addr_res[3];
                        volatile u8     status;         /* descriptor status */
                } __attribute__((packed)) rd_s;
        } __attribute((packed)) rd_u;
} __attribute__ ((packed));

#define rd_addr         rd_u.addr
#define rd_status       rd_u.rd_s.status

/* ring descriptor status bits */

#define RD_ACTIVE               0x80    /* descriptor owned by hw (both TX,RX) */

/* TX ring descriptor status */

#define RD_TX_DISCRC            0x40    /* do not send CRC (for SIR) */
#define RD_TX_BADCRC            0x20    /* force a bad CRC */
#define RD_TX_PULSE             0x10    /* send indication pulse after this frame (MIR/FIR) */
#define RD_TX_FRCEUND           0x08    /* force underrun */
#define RD_TX_CLRENTX           0x04    /* clear ENTX after this frame */
#define RD_TX_UNDRN             0x01    /* TX fifo underrun (probably PCI problem) */

/* RX ring descriptor status */

#define RD_RX_PHYERR            0x40    /* physical encoding error */
#define RD_RX_CRCERR            0x20    /* CRC error (MIR/FIR) */
#define RD_RX_LENGTH            0x10    /* frame exceeds buffer length */
#define RD_RX_OVER              0x08    /* RX fifo overrun (probably PCI problem) */
#define RD_RX_SIRBAD            0x04    /* EOF missing: BOF follows BOF (SIR, filtered) */

#define RD_RX_ERROR             0x7c    /* any error in received frame */

/* the memory required to hold the 2 descriptor rings */
#define HW_RING_AREA_SIZE       (2 * MAX_RING_DESCR * sizeof(struct ring_descr_hw))

/******************************************************************/

/* sw-ring descriptors consists of a bus-mapped transfer buffer with
 * associated skb and a pointer to the hw entry descriptor
 */

struct ring_descr {
        struct ring_descr_hw    *hw;
        struct sk_buff          *skb;
        void                    *buf;
};

/* wrappers for operations on hw-exposed ring descriptors
 * access to the hw-part of the descriptors must use these.
 */

static inline int rd_is_active(struct ring_descr *rd)
{
        return ((rd->hw->rd_status & RD_ACTIVE) != 0);
}

static inline void rd_activate(struct ring_descr *rd)
{
        rd->hw->rd_status |= RD_ACTIVE;
}

static inline void rd_set_status(struct ring_descr *rd, u8 s)
{
        rd->hw->rd_status = s;   /* may pass ownership to the hardware */
}

static inline void rd_set_addr_status(struct ring_descr *rd, dma_addr_t a, u8 s)
{
        /* order is important for two reasons:
         *  - overlayed: writing addr overwrites status
         *  - we want to write status last so we have valid address in
         *    case status has RD_ACTIVE set
         */

        if ((a & ~DMA_MASK_MSTRPAGE)>>24 != MSTRPAGE_VALUE) {
                IRDA_ERROR("%s: pci busaddr inconsistency!\n", __FUNCTION__);
                dump_stack();
                return;
        }

        a &= DMA_MASK_MSTRPAGE;  /* clear highbyte to make sure we won't write
                                  * to status - just in case MSTRPAGE_VALUE!=0
                                  */
        rd->hw->rd_addr = cpu_to_le32(a);
        wmb();
        rd_set_status(rd, s);    /* may pass ownership to the hardware */
}

static inline void rd_set_count(struct ring_descr *rd, u16 c)
{
        rd->hw->rd_count = cpu_to_le16(c);
}

static inline u8 rd_get_status(struct ring_descr *rd)
{
        return rd->hw->rd_status;
}

static inline dma_addr_t rd_get_addr(struct ring_descr *rd)
{
        dma_addr_t      a;

        a = le32_to_cpu(rd->hw->rd_addr);
        return (a & DMA_MASK_MSTRPAGE) | (MSTRPAGE_VALUE << 24);
}

static inline u16 rd_get_count(struct ring_descr *rd)
{
        return le16_to_cpu(rd->hw->rd_count);
}

/******************************************************************/

/* sw descriptor rings for rx, tx:
 *
 * operations follow producer-consumer paradigm, with the hw
 * in the middle doing the processing.
 * ring size must be power of two.
 *
 * producer advances r->tail after inserting for processing
 * consumer advances r->head after removing processed rd
 * ring is empty if head==tail / full if (tail+1)==head
 */

struct vlsi_ring {
        struct pci_dev          *pdev;
        int                     dir;
        unsigned                len;
        unsigned                size;
        unsigned                mask;
        atomic_t                head, tail;
        struct ring_descr       *rd;
};

/* ring processing helpers */

static inline struct ring_descr *ring_last(struct vlsi_ring *r)
{
        int t;

        t = atomic_read(&r->tail) & r->mask;
        return (((t+1) & r->mask) == (atomic_read(&r->head) & r->mask)) ? NULL : &r->rd[t];
}

static inline struct ring_descr *ring_put(struct vlsi_ring *r)
{
        atomic_inc(&r->tail);
        return ring_last(r);
}

static inline struct ring_descr *ring_first(struct vlsi_ring *r)
{
        int h;

        h = atomic_read(&r->head) & r->mask;
        return (h == (atomic_read(&r->tail) & r->mask)) ? NULL : &r->rd[h];
}

static inline struct ring_descr *ring_get(struct vlsi_ring *r)
{
        atomic_inc(&r->head);
        return ring_first(r);
}

/******************************************************************/

/* our private compound VLSI-PCI-IRDA device information */

typedef struct vlsi_irda_dev {
        struct pci_dev          *pdev;
        struct net_device_stats stats;

        struct irlap_cb         *irlap;

        struct qos_info         qos;

        unsigned                mode;
        int                     baud, new_baud;

        dma_addr_t              busaddr;
        void                    *virtaddr;
        struct vlsi_ring        *tx_ring, *rx_ring;

        struct timeval          last_rx;

        spinlock_t              lock;
        struct semaphore        sem;

        u8                      resume_ok;      
        struct proc_dir_entry   *proc_entry;

} vlsi_irda_dev_t;

/********************************************************/

/* the remapped error flags we use for returning from frame
 * post-processing in vlsi_process_tx/rx() after it was completed
 * by the hardware. These functions either return the >=0 number
 * of transfered bytes in case of success or the negative (-)
 * of the or'ed error flags.
 */

#define VLSI_TX_DROP            0x0001
#define VLSI_TX_FIFO            0x0002

#define VLSI_RX_DROP            0x0100
#define VLSI_RX_OVER            0x0200
#define VLSI_RX_LENGTH          0x0400
#define VLSI_RX_FRAME           0x0800
#define VLSI_RX_CRC             0x1000

/********************************************************/

#endif /* IRDA_VLSI_FIR_H */