Introduce "hcall" pointer to indicate pending hypercall.

[linux-2.6] / drivers / lguest / x86 / core.c

/*
 * Copyright (C) 2006, Rusty Russell <rusty@rustcorp.com.au> IBM Corporation.
 * Copyright (C) 2007, Jes Sorensen <jes@sgi.com> SGI.
 *
 * This program is free software; you can redistribute it and/or modify
 * it under the terms of the GNU General Public License as published by
 * the Free Software Foundation; either version 2 of the License, or
 * (at your option) any later version.
 *
 * This program is distributed in the hope that it will be useful, but
 * WITHOUT ANY WARRANTY; without even the implied warranty of
 * MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, GOOD TITLE or
 * NON INFRINGEMENT.  See the GNU General Public License for more
 * details.
 *
 * You should have received a copy of the GNU General Public License
 * along with this program; if not, write to the Free Software
 * Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA.
 */
#include <linux/kernel.h>
#include <linux/start_kernel.h>
#include <linux/string.h>
#include <linux/console.h>
#include <linux/screen_info.h>
#include <linux/irq.h>
#include <linux/interrupt.h>
#include <linux/clocksource.h>
#include <linux/clockchips.h>
#include <linux/cpu.h>
#include <linux/lguest.h>
#include <linux/lguest_launcher.h>
#include <linux/lguest_bus.h>
#include <asm/paravirt.h>
#include <asm/param.h>
#include <asm/page.h>
#include <asm/pgtable.h>
#include <asm/desc.h>
#include <asm/setup.h>
#include <asm/lguest.h>
#include <asm/uaccess.h>
#include <asm/i387.h>
#include "../lg.h"

static int cpu_had_pge;

static struct {
        unsigned long offset;
        unsigned short segment;
} lguest_entry;

/* Offset from where switcher.S was compiled to where we've copied it */
static unsigned long switcher_offset(void)
{
        return SWITCHER_ADDR - (unsigned long)start_switcher_text;
}

/* This cpu's struct lguest_pages. */
static struct lguest_pages *lguest_pages(unsigned int cpu)
{
        return &(((struct lguest_pages *)
                  (SWITCHER_ADDR + SHARED_SWITCHER_PAGES*PAGE_SIZE))[cpu]);
}

static DEFINE_PER_CPU(struct lguest *, last_guest);

/*S:010
 * We are getting close to the Switcher.
 *
 * Remember that each CPU has two pages which are visible to the Guest when it
 * runs on that CPU.  This has to contain the state for that Guest: we copy the
 * state in just before we run the Guest.
 *
 * Each Guest has "changed" flags which indicate what has changed in the Guest
 * since it last ran.  We saw this set in interrupts_and_traps.c and
 * segments.c.
 */
static void copy_in_guest_info(struct lguest *lg, struct lguest_pages *pages)
{
        /* Copying all this data can be quite expensive.  We usually run the
         * same Guest we ran last time (and that Guest hasn't run anywhere else
         * meanwhile).  If that's not the case, we pretend everything in the
         * Guest has changed. */
        if (__get_cpu_var(last_guest) != lg || lg->last_pages != pages) {
                __get_cpu_var(last_guest) = lg;
                lg->last_pages = pages;
                lg->changed = CHANGED_ALL;
        }

        /* These copies are pretty cheap, so we do them unconditionally: */
        /* Save the current Host top-level page directory. */
        pages->state.host_cr3 = __pa(current->mm->pgd);
        /* Set up the Guest's page tables to see this CPU's pages (and no
         * other CPU's pages). */
        map_switcher_in_guest(lg, pages);
        /* Set up the two "TSS" members which tell the CPU what stack to use
         * for traps which do directly into the Guest (ie. traps at privilege
         * level 1). */
        pages->state.guest_tss.esp1 = lg->esp1;
        pages->state.guest_tss.ss1 = lg->ss1;

        /* Copy direct-to-Guest trap entries. */
        if (lg->changed & CHANGED_IDT)
                copy_traps(lg, pages->state.guest_idt, default_idt_entries);

        /* Copy all GDT entries which the Guest can change. */
        if (lg->changed & CHANGED_GDT)
                copy_gdt(lg, pages->state.guest_gdt);
        /* If only the TLS entries have changed, copy them. */
        else if (lg->changed & CHANGED_GDT_TLS)
                copy_gdt_tls(lg, pages->state.guest_gdt);

        /* Mark the Guest as unchanged for next time. */
        lg->changed = 0;
}

/* Finally: the code to actually call into the Switcher to run the Guest. */
static void run_guest_once(struct lguest *lg, struct lguest_pages *pages)
{
        /* This is a dummy value we need for GCC's sake. */
        unsigned int clobber;

        /* Copy the guest-specific information into this CPU's "struct
         * lguest_pages". */
        copy_in_guest_info(lg, pages);

        /* Set the trap number to 256 (impossible value).  If we fault while
         * switching to the Guest (bad segment registers or bug), this will
         * cause us to abort the Guest. */
        lg->regs->trapnum = 256;

        /* Now: we push the "eflags" register on the stack, then do an "lcall".
         * This is how we change from using the kernel code segment to using
         * the dedicated lguest code segment, as well as jumping into the
         * Switcher.
         *
         * The lcall also pushes the old code segment (KERNEL_CS) onto the
         * stack, then the address of this call.  This stack layout happens to
         * exactly match the stack of an interrupt... */
        asm volatile("pushf; lcall *lguest_entry"
                     /* This is how we tell GCC that %eax ("a") and %ebx ("b")
                      * are changed by this routine.  The "=" means output. */
                     : "=a"(clobber), "=b"(clobber)
                     /* %eax contains the pages pointer.  ("0" refers to the
                      * 0-th argument above, ie "a").  %ebx contains the
                      * physical address of the Guest's top-level page
                      * directory. */
                     : "0"(pages), "1"(__pa(lg->pgdirs[lg->pgdidx].pgdir))
                     /* We tell gcc that all these registers could change,
                      * which means we don't have to save and restore them in
                      * the Switcher. */
                     : "memory", "%edx", "%ecx", "%edi", "%esi");
}
/*:*/

/*H:040 This is the i386-specific code to setup and run the Guest.  Interrupts
 * are disabled: we own the CPU. */
void lguest_arch_run_guest(struct lguest *lg)
{
        /* Remember the awfully-named TS bit?  If the Guest has asked
         * to set it we set it now, so we can trap and pass that trap
         * to the Guest if it uses the FPU. */
        if (lg->ts)
                lguest_set_ts();

        /* SYSENTER is an optimized way of doing system calls.  We
         * can't allow it because it always jumps to privilege level 0.
         * A normal Guest won't try it because we don't advertise it in
         * CPUID, but a malicious Guest (or malicious Guest userspace
         * program) could, so we tell the CPU to disable it before
         * running the Guest. */
        if (boot_cpu_has(X86_FEATURE_SEP))
                wrmsr(MSR_IA32_SYSENTER_CS, 0, 0);

        /* Now we actually run the Guest.  It will pop back out when
         * something interesting happens, and we can examine its
         * registers to see what it was doing. */
        run_guest_once(lg, lguest_pages(raw_smp_processor_id()));

        /* The "regs" pointer contains two extra entries which are not
         * really registers: a trap number which says what interrupt or
         * trap made the switcher code come back, and an error code
         * which some traps set.  */

        /* If the Guest page faulted, then the cr2 register will tell
         * us the bad virtual address.  We have to grab this now,
         * because once we re-enable interrupts an interrupt could
         * fault and thus overwrite cr2, or we could even move off to a
         * different CPU. */
        if (lg->regs->trapnum == 14)
                lg->arch.last_pagefault = read_cr2();
        /* Similarly, if we took a trap because the Guest used the FPU,
         * we have to restore the FPU it expects to see. */
        else if (lg->regs->trapnum == 7)
                math_state_restore();

        /* Restore SYSENTER if it's supposed to be on. */
        if (boot_cpu_has(X86_FEATURE_SEP))
                wrmsr(MSR_IA32_SYSENTER_CS, __KERNEL_CS, 0);
}

/*H:130 Our Guest is usually so well behaved; it never tries to do things it
 * isn't allowed to.  Unfortunately, Linux's paravirtual infrastructure isn't
 * quite complete, because it doesn't contain replacements for the Intel I/O
 * instructions.  As a result, the Guest sometimes fumbles across one during
 * the boot process as it probes for various things which are usually attached
 * to a PC.
 *
 * When the Guest uses one of these instructions, we get trap #13 (General
 * Protection Fault) and come here.  We see if it's one of those troublesome
 * instructions and skip over it.  We return true if we did. */
static int emulate_insn(struct lguest *lg)
{
        u8 insn;
        unsigned int insnlen = 0, in = 0, shift = 0;
        /* The eip contains the *virtual* address of the Guest's instruction:
         * guest_pa just subtracts the Guest's page_offset. */
        unsigned long physaddr = guest_pa(lg, lg->regs->eip);

        /* The guest_pa() function only works for Guest kernel addresses, but
         * that's all we're trying to do anyway. */
        if (lg->regs->eip < lg->page_offset)
                return 0;

        /* Decoding x86 instructions is icky. */
        lgread(lg, &insn, physaddr, 1);

        /* 0x66 is an "operand prefix".  It means it's using the upper 16 bits
           of the eax register. */
        if (insn == 0x66) {
                shift = 16;
                /* The instruction is 1 byte so far, read the next byte. */
                insnlen = 1;
                lgread(lg, &insn, physaddr + insnlen, 1);
        }

        /* We can ignore the lower bit for the moment and decode the 4 opcodes
         * we need to emulate. */
        switch (insn & 0xFE) {
        case 0xE4: /* in     <next byte>,%al */
                insnlen += 2;
                in = 1;
                break;
        case 0xEC: /* in     (%dx),%al */
                insnlen += 1;
                in = 1;
                break;
        case 0xE6: /* out    %al,<next byte> */
                insnlen += 2;
                break;
        case 0xEE: /* out    %al,(%dx) */
                insnlen += 1;
                break;
        default:
                /* OK, we don't know what this is, can't emulate. */
                return 0;
        }

        /* If it was an "IN" instruction, they expect the result to be read
         * into %eax, so we change %eax.  We always return all-ones, which
         * traditionally means "there's nothing there". */
        if (in) {
                /* Lower bit tells is whether it's a 16 or 32 bit access */
                if (insn & 0x1)
                        lg->regs->eax = 0xFFFFFFFF;
                else
                        lg->regs->eax |= (0xFFFF << shift);
        }
        /* Finally, we've "done" the instruction, so move past it. */
        lg->regs->eip += insnlen;
        /* Success! */
        return 1;
}

/*H:050 Once we've re-enabled interrupts, we look at why the Guest exited. */
void lguest_arch_handle_trap(struct lguest *lg)
{
        switch (lg->regs->trapnum) {
        case 13: /* We've intercepted a GPF. */
                 /* Check if this was one of those annoying IN or OUT
                  * instructions which we need to emulate.  If so, we
                  * just go back into the Guest after we've done it. */
                if (lg->regs->errcode == 0) {
                        if (emulate_insn(lg))
                                return;
                }
                break;
        case 14: /* We've intercepted a page fault. */
                 /* The Guest accessed a virtual address that wasn't
                  * mapped.  This happens a lot: we don't actually set
                  * up most of the page tables for the Guest at all when
                  * we start: as it runs it asks for more and more, and
                  * we set them up as required. In this case, we don't
                  * even tell the Guest that the fault happened.
                  *
                  * The errcode tells whether this was a read or a
                  * write, and whether kernel or userspace code. */
                if (demand_page(lg, lg->arch.last_pagefault, lg->regs->errcode))
                        return;

                 /* OK, it's really not there (or not OK): the Guest
                  * needs to know.  We write out the cr2 value so it
                  * knows where the fault occurred.
                  *
                  * Note that if the Guest were really messed up, this
                  * could happen before it's done the INITIALIZE
                  * hypercall, so lg->lguest_data will be NULL */
                if (lg->lguest_data &&
                    put_user(lg->arch.last_pagefault, &lg->lguest_data->cr2))
                        kill_guest(lg, "Writing cr2");
                break;
        case 7: /* We've intercepted a Device Not Available fault. */
                /* If the Guest doesn't want to know, we already
                 * restored the Floating Point Unit, so we just
                 * continue without telling it. */
                if (!lg->ts)
                        return;
                break;
        case 32 ... 255:
                /* These values mean a real interrupt occurred, in which case
                 * the Host handler has already been run.  We just do a
                 * friendly check if another process should now be run, then
                 * return to run the Guest again */
                cond_resched();
                return;
        case LGUEST_TRAP_ENTRY:
                lg->hcall = lg->regs;
                return;
        }

        /* We didn't handle the trap, so it needs to go to the Guest. */
        if (!deliver_trap(lg, lg->regs->trapnum))
                /* If the Guest doesn't have a handler (either it hasn't
                 * registered any yet, or it's one of the faults we don't let
                 * it handle), it dies with a cryptic error message. */
                kill_guest(lg, "unhandled trap %li at %#lx (%#lx)",
                           lg->regs->trapnum, lg->regs->eip,
                           lg->regs->trapnum == 14 ? lg->arch.last_pagefault
                           : lg->regs->errcode);
}

/* Now we can look at each of the routines this calls, in increasing order of
 * complexity: do_hypercalls(), emulate_insn(), maybe_do_interrupt(),
 * deliver_trap() and demand_page().  After all those, we'll be ready to
 * examine the Switcher, and our philosophical understanding of the Host/Guest
 * duality will be complete. :*/
static void adjust_pge(void *on)
{
        if (on)
                write_cr4(read_cr4() | X86_CR4_PGE);
        else
                write_cr4(read_cr4() & ~X86_CR4_PGE);
}

/*H:020 Now the Switcher is mapped and every thing else is ready, we need to do
 * some more i386-specific initialization. */
void __init lguest_arch_host_init(void)
{
        int i;

        /* Most of the i386/switcher.S doesn't care that it's been moved; on
         * Intel, jumps are relative, and it doesn't access any references to
         * external code or data.
         *
         * The only exception is the interrupt handlers in switcher.S: their
         * addresses are placed in a table (default_idt_entries), so we need to
         * update the table with the new addresses.  switcher_offset() is a
         * convenience function which returns the distance between the builtin
         * switcher code and the high-mapped copy we just made. */
        for (i = 0; i < IDT_ENTRIES; i++)
                default_idt_entries[i] += switcher_offset();

        /*
         * Set up the Switcher's per-cpu areas.
         *
         * Each CPU gets two pages of its own within the high-mapped region
         * (aka. "struct lguest_pages").  Much of this can be initialized now,
         * but some depends on what Guest we are running (which is set up in
         * copy_in_guest_info()).
         */
        for_each_possible_cpu(i) {
                /* lguest_pages() returns this CPU's two pages. */
                struct lguest_pages *pages = lguest_pages(i);
                /* This is a convenience pointer to make the code fit one
                 * statement to a line. */
                struct lguest_ro_state *state = &pages->state;

                /* The Global Descriptor Table: the Host has a different one
                 * for each CPU.  We keep a descriptor for the GDT which says
                 * where it is and how big it is (the size is actually the last
                 * byte, not the size, hence the "-1"). */
                state->host_gdt_desc.size = GDT_SIZE-1;
                state->host_gdt_desc.address = (long)get_cpu_gdt_table(i);

                /* All CPUs on the Host use the same Interrupt Descriptor
                 * Table, so we just use store_idt(), which gets this CPU's IDT
                 * descriptor. */
                store_idt(&state->host_idt_desc);

                /* The descriptors for the Guest's GDT and IDT can be filled
                 * out now, too.  We copy the GDT & IDT into ->guest_gdt and
                 * ->guest_idt before actually running the Guest. */
                state->guest_idt_desc.size = sizeof(state->guest_idt)-1;
                state->guest_idt_desc.address = (long)&state->guest_idt;
                state->guest_gdt_desc.size = sizeof(state->guest_gdt)-1;
                state->guest_gdt_desc.address = (long)&state->guest_gdt;

                /* We know where we want the stack to be when the Guest enters
                 * the switcher: in pages->regs.  The stack grows upwards, so
                 * we start it at the end of that structure. */
                state->guest_tss.esp0 = (long)(&pages->regs + 1);
                /* And this is the GDT entry to use for the stack: we keep a
                 * couple of special LGUEST entries. */
                state->guest_tss.ss0 = LGUEST_DS;

                /* x86 can have a finegrained bitmap which indicates what I/O
                 * ports the process can use.  We set it to the end of our
                 * structure, meaning "none". */
                state->guest_tss.io_bitmap_base = sizeof(state->guest_tss);

                /* Some GDT entries are the same across all Guests, so we can
                 * set them up now. */
                setup_default_gdt_entries(state);
                /* Most IDT entries are the same for all Guests, too.*/
                setup_default_idt_entries(state, default_idt_entries);

                /* The Host needs to be able to use the LGUEST segments on this
                 * CPU, too, so put them in the Host GDT. */
                get_cpu_gdt_table(i)[GDT_ENTRY_LGUEST_CS] = FULL_EXEC_SEGMENT;
                get_cpu_gdt_table(i)[GDT_ENTRY_LGUEST_DS] = FULL_SEGMENT;
        }

        /* In the Switcher, we want the %cs segment register to use the
         * LGUEST_CS GDT entry: we've put that in the Host and Guest GDTs, so
         * it will be undisturbed when we switch.  To change %cs and jump we
         * need this structure to feed to Intel's "lcall" instruction. */
        lguest_entry.offset = (long)switch_to_guest + switcher_offset();
        lguest_entry.segment = LGUEST_CS;

        /* Finally, we need to turn off "Page Global Enable".  PGE is an
         * optimization where page table entries are specially marked to show
         * they never change.  The Host kernel marks all the kernel pages this
         * way because it's always present, even when userspace is running.
         *
         * Lguest breaks this: unbeknownst to the rest of the Host kernel, we
         * switch to the Guest kernel.  If you don't disable this on all CPUs,
         * you'll get really weird bugs that you'll chase for two days.
         *
         * I used to turn PGE off every time we switched to the Guest and back
         * on when we return, but that slowed the Switcher down noticibly. */

        /* We don't need the complexity of CPUs coming and going while we're
         * doing this. */
        lock_cpu_hotplug();
        if (cpu_has_pge) { /* We have a broader idea of "global". */
                /* Remember that this was originally set (for cleanup). */
                cpu_had_pge = 1;
                /* adjust_pge is a helper function which sets or unsets the PGE
                 * bit on its CPU, depending on the argument (0 == unset). */
                on_each_cpu(adjust_pge, (void *)0, 0, 1);
                /* Turn off the feature in the global feature set. */
                clear_bit(X86_FEATURE_PGE, boot_cpu_data.x86_capability);
        }
        unlock_cpu_hotplug();
};
/*:*/

void __exit lguest_arch_host_fini(void)
{
        /* If we had PGE before we started, turn it back on now. */
        lock_cpu_hotplug();
        if (cpu_had_pge) {
                set_bit(X86_FEATURE_PGE, boot_cpu_data.x86_capability);
                /* adjust_pge's argument "1" means set PGE. */
                on_each_cpu(adjust_pge, (void *)1, 0, 1);
        }
        unlock_cpu_hotplug();
}