1 USB device persistence during system suspend
3 Alan Stern <stern@rowland.harvard.edu>
5 September 2, 2006 (Updated May 29, 2007)
10 According to the USB specification, when a USB bus is suspended the
11 bus must continue to supply suspend current (around 1-5 mA). This
12 is so that devices can maintain their internal state and hubs can
13 detect connect-change events (devices being plugged in or unplugged).
14 The technical term is "power session".
16 If a USB device's power session is interrupted then the system is
17 required to behave as though the device has been unplugged. It's a
18 conservative approach; in the absence of suspend current the computer
19 has no way to know what has actually happened. Perhaps the same
20 device is still attached or perhaps it was removed and a different
21 device plugged into the port. The system must assume the worst.
23 By default, Linux behaves according to the spec. If a USB host
24 controller loses power during a system suspend, then when the system
25 wakes up all the devices attached to that controller are treated as
26 though they had disconnected. This is always safe and it is the
27 "officially correct" thing to do.
29 For many sorts of devices this behavior doesn't matter in the least.
30 If the kernel wants to believe that your USB keyboard was unplugged
31 while the system was asleep and a new keyboard was plugged in when the
32 system woke up, who cares? It'll still work the same when you type on
35 Unfortunately problems _can_ arise, particularly with mass-storage
36 devices. The effect is exactly the same as if the device really had
37 been unplugged while the system was suspended. If you had a mounted
38 filesystem on the device, you're out of luck -- everything in that
39 filesystem is now inaccessible. This is especially annoying if your
40 root filesystem was located on the device, since your system will
43 Loss of power isn't the only mechanism to worry about. Anything that
44 interrupts a power session will have the same effect. For example,
45 even though suspend current may have been maintained while the system
46 was asleep, on many systems during the initial stages of wakeup the
47 firmware (i.e., the BIOS) resets the motherboard's USB host
48 controllers. Result: all the power sessions are destroyed and again
49 it's as though you had unplugged all the USB devices. Yes, it's
50 entirely the BIOS's fault, but that doesn't do _you_ any good unless
51 you can convince the BIOS supplier to fix the problem (lots of luck!).
53 On many systems the USB host controllers will get reset after a
54 suspend-to-RAM. On almost all systems, no suspend current is
55 available during hibernation (also known as swsusp or suspend-to-disk).
56 You can check the kernel log after resuming to see if either of these
57 has happened; look for lines saying "root hub lost power or was reset".
59 In practice, people are forced to unmount any filesystems on a USB
60 device before suspending. If the root filesystem is on a USB device,
61 the system can't be suspended at all. (All right, it _can_ be
62 suspended -- but it will crash as soon as it wakes up, which isn't
68 Setting CONFIG_USB_PERSIST will cause the kernel to work around these
69 issues. It enables a mode in which the core USB device data
70 structures are allowed to persist across a power-session disruption.
71 It works like this. If the kernel sees that a USB host controller is
72 not in the expected state during resume (i.e., if the controller was
73 reset or otherwise had lost power) then it applies a persistence check
74 to each of the USB devices below that controller for which the
75 "persist" attribute is set. It doesn't try to resume the device; that
76 can't work once the power session is gone. Instead it issues a USB
77 port reset and then re-enumerates the device. (This is exactly the
78 same thing that happens whenever a USB device is reset.) If the
79 re-enumeration shows that the device now attached to that port has the
80 same descriptors as before, including the Vendor and Product IDs, then
81 the kernel continues to use the same device structure. In effect, the
82 kernel treats the device as though it had merely been reset instead of
85 If no device is now attached to the port, or if the descriptors are
86 different from what the kernel remembers, then the treatment is what
87 you would expect. The kernel destroys the old device structure and
88 behaves as though the old device had been unplugged and a new device
89 plugged in, just as it would without the CONFIG_USB_PERSIST option.
91 The end result is that the USB device remains available and usable.
92 Filesystem mounts and memory mappings are unaffected, and the world is
93 now a good and happy place.
95 Note that even when CONFIG_USB_PERSIST is set, the "persist" feature
96 will be applied only to those devices for which it is enabled. You
97 can enable the feature by doing (as root):
99 echo 1 >/sys/bus/usb/devices/.../power/persist
101 where the "..." should be filled in the with the device's ID. Disable
102 the feature by writing 0 instead of 1. For hubs the feature is
103 automatically and permanently enabled, so you only have to worry about
104 setting it for devices where it really matters.
107 Is this the best solution?
109 Perhaps not. Arguably, keeping track of mounted filesystems and
110 memory mappings across device disconnects should be handled by a
111 centralized Logical Volume Manager. Such a solution would allow you
112 to plug in a USB flash device, create a persistent volume associated
113 with it, unplug the flash device, plug it back in later, and still
114 have the same persistent volume associated with the device. As such
115 it would be more far-reaching than CONFIG_USB_PERSIST.
117 On the other hand, writing a persistent volume manager would be a big
118 job and using it would require significant input from the user. This
119 solution is much quicker and easier -- and it exists now, a giant
122 Furthermore, the USB_PERSIST option applies to _all_ USB devices, not
123 just mass-storage devices. It might turn out to be equally useful for
124 other device types, such as network interfaces.
127 WARNING: Using CONFIG_USB_PERSIST can be dangerous!!
129 When recovering an interrupted power session the kernel does its best
130 to make sure the USB device hasn't been changed; that is, the same
131 device is still plugged into the port as before. But the checks
132 aren't guaranteed to be 100% accurate.
134 If you replace one USB device with another of the same type (same
135 manufacturer, same IDs, and so on) there's an excellent chance the
136 kernel won't detect the change. Serial numbers and other strings are
137 not compared. In many cases it wouldn't help if they were, because
138 manufacturers frequently omit serial numbers entirely in their
141 Furthermore it's quite possible to leave a USB device exactly the same
142 while changing its media. If you replace the flash memory card in a
143 USB card reader while the system is asleep, the kernel will have no
144 way to know you did it. The kernel will assume that nothing has
145 happened and will continue to use the partition tables, inodes, and
146 memory mappings for the old card.
148 If the kernel gets fooled in this way, it's almost certain to cause
149 data corruption and to crash your system. You'll have no one to blame
152 YOU HAVE BEEN WARNED! USE AT YOUR OWN RISK!
154 That having been said, most of the time there shouldn't be any trouble
155 at all. The "persist" feature can be extremely useful. Make the most
projects / linux-2.6 / blob