ide-disk: use ata_id_hpa_enabled()

[linux-2.6] / drivers / scsi / scsi_scan.c

/*
 * scsi_scan.c
 *
 * Copyright (C) 2000 Eric Youngdale,
 * Copyright (C) 2002 Patrick Mansfield
 *
 * The general scanning/probing algorithm is as follows, exceptions are
 * made to it depending on device specific flags, compilation options, and
 * global variable (boot or module load time) settings.
 *
 * A specific LUN is scanned via an INQUIRY command; if the LUN has a
 * device attached, a scsi_device is allocated and setup for it.
 *
 * For every id of every channel on the given host:
 *
 *      Scan LUN 0; if the target responds to LUN 0 (even if there is no
 *      device or storage attached to LUN 0):
 *
 *              If LUN 0 has a device attached, allocate and setup a
 *              scsi_device for it.
 *
 *              If target is SCSI-3 or up, issue a REPORT LUN, and scan
 *              all of the LUNs returned by the REPORT LUN; else,
 *              sequentially scan LUNs up until some maximum is reached,
 *              or a LUN is seen that cannot have a device attached to it.
 */

#include <linux/module.h>
#include <linux/moduleparam.h>
#include <linux/init.h>
#include <linux/blkdev.h>
#include <linux/delay.h>
#include <linux/kthread.h>
#include <linux/spinlock.h>

#include <scsi/scsi.h>
#include <scsi/scsi_cmnd.h>
#include <scsi/scsi_device.h>
#include <scsi/scsi_driver.h>
#include <scsi/scsi_devinfo.h>
#include <scsi/scsi_host.h>
#include <scsi/scsi_transport.h>
#include <scsi/scsi_eh.h>

#include "scsi_priv.h"
#include "scsi_logging.h"

#define ALLOC_FAILURE_MSG       KERN_ERR "%s: Allocation failure during" \
        " SCSI scanning, some SCSI devices might not be configured\n"

/*
 * Default timeout
 */
#define SCSI_TIMEOUT (2*HZ)

/*
 * Prefix values for the SCSI id's (stored in sysfs name field)
 */
#define SCSI_UID_SER_NUM 'S'
#define SCSI_UID_UNKNOWN 'Z'

/*
 * Return values of some of the scanning functions.
 *
 * SCSI_SCAN_NO_RESPONSE: no valid response received from the target, this
 * includes allocation or general failures preventing IO from being sent.
 *
 * SCSI_SCAN_TARGET_PRESENT: target responded, but no device is available
 * on the given LUN.
 *
 * SCSI_SCAN_LUN_PRESENT: target responded, and a device is available on a
 * given LUN.
 */
#define SCSI_SCAN_NO_RESPONSE           0
#define SCSI_SCAN_TARGET_PRESENT        1
#define SCSI_SCAN_LUN_PRESENT           2

static const char *scsi_null_device_strs = "nullnullnullnull";

#define MAX_SCSI_LUNS   512

#ifdef CONFIG_SCSI_MULTI_LUN
static unsigned int max_scsi_luns = MAX_SCSI_LUNS;
#else
static unsigned int max_scsi_luns = 1;
#endif

module_param_named(max_luns, max_scsi_luns, uint, S_IRUGO|S_IWUSR);
MODULE_PARM_DESC(max_luns,
                 "last scsi LUN (should be between 1 and 2^32-1)");

#ifdef CONFIG_SCSI_SCAN_ASYNC
#define SCSI_SCAN_TYPE_DEFAULT "async"
#else
#define SCSI_SCAN_TYPE_DEFAULT "sync"
#endif

static char scsi_scan_type[6] = SCSI_SCAN_TYPE_DEFAULT;

module_param_string(scan, scsi_scan_type, sizeof(scsi_scan_type), S_IRUGO);
MODULE_PARM_DESC(scan, "sync, async or none");

/*
 * max_scsi_report_luns: the maximum number of LUNS that will be
 * returned from the REPORT LUNS command. 8 times this value must
 * be allocated. In theory this could be up to an 8 byte value, but
 * in practice, the maximum number of LUNs suppored by any device
 * is about 16k.
 */
static unsigned int max_scsi_report_luns = 511;

module_param_named(max_report_luns, max_scsi_report_luns, uint, S_IRUGO|S_IWUSR);
MODULE_PARM_DESC(max_report_luns,
                 "REPORT LUNS maximum number of LUNS received (should be"
                 " between 1 and 16384)");

static unsigned int scsi_inq_timeout = SCSI_TIMEOUT/HZ+3;

module_param_named(inq_timeout, scsi_inq_timeout, uint, S_IRUGO|S_IWUSR);
MODULE_PARM_DESC(inq_timeout, 
                 "Timeout (in seconds) waiting for devices to answer INQUIRY."
                 " Default is 5. Some non-compliant devices need more.");

/* This lock protects only this list */
static DEFINE_SPINLOCK(async_scan_lock);
static LIST_HEAD(scanning_hosts);

struct async_scan_data {
        struct list_head list;
        struct Scsi_Host *shost;
        struct completion prev_finished;
};

/**
 * scsi_complete_async_scans - Wait for asynchronous scans to complete
 *
 * When this function returns, any host which started scanning before
 * this function was called will have finished its scan.  Hosts which
 * started scanning after this function was called may or may not have
 * finished.
 */
int scsi_complete_async_scans(void)
{
        struct async_scan_data *data;

        do {
                if (list_empty(&scanning_hosts))
                        return 0;
                /* If we can't get memory immediately, that's OK.  Just
                 * sleep a little.  Even if we never get memory, the async
                 * scans will finish eventually.
                 */
                data = kmalloc(sizeof(*data), GFP_KERNEL);
                if (!data)
                        msleep(1);
        } while (!data);

        data->shost = NULL;
        init_completion(&data->prev_finished);

        spin_lock(&async_scan_lock);
        /* Check that there's still somebody else on the list */
        if (list_empty(&scanning_hosts))
                goto done;
        list_add_tail(&data->list, &scanning_hosts);
        spin_unlock(&async_scan_lock);

        printk(KERN_INFO "scsi: waiting for bus probes to complete ...\n");
        wait_for_completion(&data->prev_finished);

        spin_lock(&async_scan_lock);
        list_del(&data->list);
        if (!list_empty(&scanning_hosts)) {
                struct async_scan_data *next = list_entry(scanning_hosts.next,
                                struct async_scan_data, list);
                complete(&next->prev_finished);
        }
 done:
        spin_unlock(&async_scan_lock);

        kfree(data);
        return 0;
}

/* Only exported for the benefit of scsi_wait_scan */
EXPORT_SYMBOL_GPL(scsi_complete_async_scans);

#ifndef MODULE
/*
 * For async scanning we need to wait for all the scans to complete before
 * trying to mount the root fs.  Otherwise non-modular drivers may not be ready
 * yet.
 */
late_initcall(scsi_complete_async_scans);
#endif

/**
 * scsi_unlock_floptical - unlock device via a special MODE SENSE command
 * @sdev:       scsi device to send command to
 * @result:     area to store the result of the MODE SENSE
 *
 * Description:
 *     Send a vendor specific MODE SENSE (not a MODE SELECT) command.
 *     Called for BLIST_KEY devices.
 **/
static void scsi_unlock_floptical(struct scsi_device *sdev,
                                  unsigned char *result)
{
        unsigned char scsi_cmd[MAX_COMMAND_SIZE];

        printk(KERN_NOTICE "scsi: unlocking floptical drive\n");
        scsi_cmd[0] = MODE_SENSE;
        scsi_cmd[1] = 0;
        scsi_cmd[2] = 0x2e;
        scsi_cmd[3] = 0;
        scsi_cmd[4] = 0x2a;     /* size */
        scsi_cmd[5] = 0;
        scsi_execute_req(sdev, scsi_cmd, DMA_FROM_DEVICE, result, 0x2a, NULL,
                         SCSI_TIMEOUT, 3);
}

/**
 * scsi_alloc_sdev - allocate and setup a scsi_Device
 * @starget: which target to allocate a &scsi_device for
 * @lun: which lun
 * @hostdata: usually NULL and set by ->slave_alloc instead
 *
 * Description:
 *     Allocate, initialize for io, and return a pointer to a scsi_Device.
 *     Stores the @shost, @channel, @id, and @lun in the scsi_Device, and
 *     adds scsi_Device to the appropriate list.
 *
 * Return value:
 *     scsi_Device pointer, or NULL on failure.
 **/
static struct scsi_device *scsi_alloc_sdev(struct scsi_target *starget,
                                           unsigned int lun, void *hostdata)
{
        struct scsi_device *sdev;
        int display_failure_msg = 1, ret;
        struct Scsi_Host *shost = dev_to_shost(starget->dev.parent);
        extern void scsi_evt_thread(struct work_struct *work);

        sdev = kzalloc(sizeof(*sdev) + shost->transportt->device_size,
                       GFP_ATOMIC);
        if (!sdev)
                goto out;

        sdev->vendor = scsi_null_device_strs;
        sdev->model = scsi_null_device_strs;
        sdev->rev = scsi_null_device_strs;
        sdev->host = shost;
        sdev->id = starget->id;
        sdev->lun = lun;
        sdev->channel = starget->channel;
        sdev->sdev_state = SDEV_CREATED;
        INIT_LIST_HEAD(&sdev->siblings);
        INIT_LIST_HEAD(&sdev->same_target_siblings);
        INIT_LIST_HEAD(&sdev->cmd_list);
        INIT_LIST_HEAD(&sdev->starved_entry);
        INIT_LIST_HEAD(&sdev->event_list);
        spin_lock_init(&sdev->list_lock);
        INIT_WORK(&sdev->event_work, scsi_evt_thread);

        sdev->sdev_gendev.parent = get_device(&starget->dev);
        sdev->sdev_target = starget;

        /* usually NULL and set by ->slave_alloc instead */
        sdev->hostdata = hostdata;

        /* if the device needs this changing, it may do so in the
         * slave_configure function */
        sdev->max_device_blocked = SCSI_DEFAULT_DEVICE_BLOCKED;

        /*
         * Some low level driver could use device->type
         */
        sdev->type = -1;

        /*
         * Assume that the device will have handshaking problems,
         * and then fix this field later if it turns out it
         * doesn't
         */
        sdev->borken = 1;

        sdev->request_queue = scsi_alloc_queue(sdev);
        if (!sdev->request_queue) {
                /* release fn is set up in scsi_sysfs_device_initialise, so
                 * have to free and put manually here */
                put_device(&starget->dev);
                kfree(sdev);
                goto out;
        }

        sdev->request_queue->queuedata = sdev;
        scsi_adjust_queue_depth(sdev, 0, sdev->host->cmd_per_lun);

        scsi_sysfs_device_initialize(sdev);

        if (shost->hostt->slave_alloc) {
                ret = shost->hostt->slave_alloc(sdev);
                if (ret) {
                        /*
                         * if LLDD reports slave not present, don't clutter
                         * console with alloc failure messages
                         */
                        if (ret == -ENXIO)
                                display_failure_msg = 0;
                        goto out_device_destroy;
                }
        }

        return sdev;

out_device_destroy:
        transport_destroy_device(&sdev->sdev_gendev);
        put_device(&sdev->sdev_gendev);
out:
        if (display_failure_msg)
                printk(ALLOC_FAILURE_MSG, __func__);
        return NULL;
}

static void scsi_target_destroy(struct scsi_target *starget)
{
        struct device *dev = &starget->dev;
        struct Scsi_Host *shost = dev_to_shost(dev->parent);
        unsigned long flags;

        transport_destroy_device(dev);
        spin_lock_irqsave(shost->host_lock, flags);
        if (shost->hostt->target_destroy)
                shost->hostt->target_destroy(starget);
        list_del_init(&starget->siblings);
        spin_unlock_irqrestore(shost->host_lock, flags);
        put_device(dev);
}

static void scsi_target_dev_release(struct device *dev)
{
        struct device *parent = dev->parent;
        struct scsi_target *starget = to_scsi_target(dev);

        kfree(starget);
        put_device(parent);
}

static struct device_type scsi_target_type = {
        .name =         "scsi_target",
        .release =      scsi_target_dev_release,
};

int scsi_is_target_device(const struct device *dev)
{
        return dev->type == &scsi_target_type;
}
EXPORT_SYMBOL(scsi_is_target_device);

static struct scsi_target *__scsi_find_target(struct device *parent,
                                              int channel, uint id)
{
        struct scsi_target *starget, *found_starget = NULL;
        struct Scsi_Host *shost = dev_to_shost(parent);
        /*
         * Search for an existing target for this sdev.
         */
        list_for_each_entry(starget, &shost->__targets, siblings) {
                if (starget->id == id &&
                    starget->channel == channel) {
                        found_starget = starget;
                        break;
                }
        }
        if (found_starget)
                get_device(&found_starget->dev);

        return found_starget;
}

/**
 * scsi_alloc_target - allocate a new or find an existing target
 * @parent:     parent of the target (need not be a scsi host)
 * @channel:    target channel number (zero if no channels)
 * @id:         target id number
 *
 * Return an existing target if one exists, provided it hasn't already
 * gone into STARGET_DEL state, otherwise allocate a new target.
 *
 * The target is returned with an incremented reference, so the caller
 * is responsible for both reaping and doing a last put
 */
static struct scsi_target *scsi_alloc_target(struct device *parent,
                                             int channel, uint id)
{
        struct Scsi_Host *shost = dev_to_shost(parent);
        struct device *dev = NULL;
        unsigned long flags;
        const int size = sizeof(struct scsi_target)
                + shost->transportt->target_size;
        struct scsi_target *starget;
        struct scsi_target *found_target;
        int error;

        starget = kzalloc(size, GFP_KERNEL);
        if (!starget) {
                printk(KERN_ERR "%s: allocation failure\n", __func__);
                return NULL;
        }
        dev = &starget->dev;
        device_initialize(dev);
        starget->reap_ref = 1;
        dev->parent = get_device(parent);
        sprintf(dev->bus_id, "target%d:%d:%d",
                shost->host_no, channel, id);
#ifndef CONFIG_SYSFS_DEPRECATED
        dev->bus = &scsi_bus_type;
#endif
        dev->type = &scsi_target_type;
        starget->id = id;
        starget->channel = channel;
        INIT_LIST_HEAD(&starget->siblings);
        INIT_LIST_HEAD(&starget->devices);
        starget->state = STARGET_CREATED;
        starget->scsi_level = SCSI_2;
 retry:
        spin_lock_irqsave(shost->host_lock, flags);

        found_target = __scsi_find_target(parent, channel, id);
        if (found_target)
                goto found;

        list_add_tail(&starget->siblings, &shost->__targets);
        spin_unlock_irqrestore(shost->host_lock, flags);
        /* allocate and add */
        transport_setup_device(dev);
        if (shost->hostt->target_alloc) {
                error = shost->hostt->target_alloc(starget);

                if(error) {
                        dev_printk(KERN_ERR, dev, "target allocation failed, error %d\n", error);
                        /* don't want scsi_target_reap to do the final
                         * put because it will be under the host lock */
                        scsi_target_destroy(starget);
                        return NULL;
                }
        }
        get_device(dev);

        return starget;

 found:
        found_target->reap_ref++;
        spin_unlock_irqrestore(shost->host_lock, flags);
        if (found_target->state != STARGET_DEL) {
                put_device(parent);
                kfree(starget);
                return found_target;
        }
        /* Unfortunately, we found a dying target; need to
         * wait until it's dead before we can get a new one */
        put_device(&found_target->dev);
        flush_scheduled_work();
        goto retry;
}

static void scsi_target_reap_usercontext(struct work_struct *work)
{
        struct scsi_target *starget =
                container_of(work, struct scsi_target, ew.work);

        transport_remove_device(&starget->dev);
        device_del(&starget->dev);
        scsi_target_destroy(starget);
}

/**
 * scsi_target_reap - check to see if target is in use and destroy if not
 * @starget: target to be checked
 *
 * This is used after removing a LUN or doing a last put of the target
 * it checks atomically that nothing is using the target and removes
 * it if so.
 */
void scsi_target_reap(struct scsi_target *starget)
{
        struct Scsi_Host *shost = dev_to_shost(starget->dev.parent);
        unsigned long flags;
        enum scsi_target_state state;
        int empty;

        spin_lock_irqsave(shost->host_lock, flags);
        state = starget->state;
        empty = --starget->reap_ref == 0 &&
                list_empty(&starget->devices) ? 1 : 0;
        spin_unlock_irqrestore(shost->host_lock, flags);

        if (!empty)
                return;

        BUG_ON(state == STARGET_DEL);
        starget->state = STARGET_DEL;
        if (state == STARGET_CREATED)
                scsi_target_destroy(starget);
        else
                execute_in_process_context(scsi_target_reap_usercontext,
                                           &starget->ew);
}

/**
 * sanitize_inquiry_string - remove non-graphical chars from an INQUIRY result string
 * @s: INQUIRY result string to sanitize
 * @len: length of the string
 *
 * Description:
 *      The SCSI spec says that INQUIRY vendor, product, and revision
 *      strings must consist entirely of graphic ASCII characters,
 *      padded on the right with spaces.  Since not all devices obey
 *      this rule, we will replace non-graphic or non-ASCII characters
 *      with spaces.  Exception: a NUL character is interpreted as a
 *      string terminator, so all the following characters are set to
 *      spaces.
 **/
static void sanitize_inquiry_string(unsigned char *s, int len)
{
        int terminated = 0;

        for (; len > 0; (--len, ++s)) {
                if (*s == 0)
                        terminated = 1;
                if (terminated || *s < 0x20 || *s > 0x7e)
                        *s = ' ';
        }
}

/**
 * scsi_probe_lun - probe a single LUN using a SCSI INQUIRY
 * @sdev:       scsi_device to probe
 * @inq_result: area to store the INQUIRY result
 * @result_len: len of inq_result
 * @bflags:     store any bflags found here
 *
 * Description:
 *     Probe the lun associated with @req using a standard SCSI INQUIRY;
 *
 *     If the INQUIRY is successful, zero is returned and the
 *     INQUIRY data is in @inq_result; the scsi_level and INQUIRY length
 *     are copied to the scsi_device any flags value is stored in *@bflags.
 **/
static int scsi_probe_lun(struct scsi_device *sdev, unsigned char *inq_result,
                          int result_len, int *bflags)
{
        unsigned char scsi_cmd[MAX_COMMAND_SIZE];
        int first_inquiry_len, try_inquiry_len, next_inquiry_len;
        int response_len = 0;
        int pass, count, result;
        struct scsi_sense_hdr sshdr;

        *bflags = 0;

        /* Perform up to 3 passes.  The first pass uses a conservative
         * transfer length of 36 unless sdev->inquiry_len specifies a
         * different value. */
        first_inquiry_len = sdev->inquiry_len ? sdev->inquiry_len : 36;
        try_inquiry_len = first_inquiry_len;
        pass = 1;

 next_pass:
        SCSI_LOG_SCAN_BUS(3, sdev_printk(KERN_INFO, sdev,
                                "scsi scan: INQUIRY pass %d length %d\n",
                                pass, try_inquiry_len));

        /* Each pass gets up to three chances to ignore Unit Attention */
        for (count = 0; count < 3; ++count) {
                memset(scsi_cmd, 0, 6);
                scsi_cmd[0] = INQUIRY;
                scsi_cmd[4] = (unsigned char) try_inquiry_len;

                memset(inq_result, 0, try_inquiry_len);

                result = scsi_execute_req(sdev,  scsi_cmd, DMA_FROM_DEVICE,
                                          inq_result, try_inquiry_len, &sshdr,
                                          HZ / 2 + HZ * scsi_inq_timeout, 3);

                SCSI_LOG_SCAN_BUS(3, printk(KERN_INFO "scsi scan: INQUIRY %s "
                                "with code 0x%x\n",
                                result ? "failed" : "successful", result));

                if (result) {
                        /*
                         * not-ready to ready transition [asc/ascq=0x28/0x0]
                         * or power-on, reset [asc/ascq=0x29/0x0], continue.
                         * INQUIRY should not yield UNIT_ATTENTION
                         * but many buggy devices do so anyway. 
                         */
                        if ((driver_byte(result) & DRIVER_SENSE) &&
                            scsi_sense_valid(&sshdr)) {
                                if ((sshdr.sense_key == UNIT_ATTENTION) &&
                                    ((sshdr.asc == 0x28) ||
                                     (sshdr.asc == 0x29)) &&
                                    (sshdr.ascq == 0))
                                        continue;
                        }
                }
                break;
        }

        if (result == 0) {
                sanitize_inquiry_string(&inq_result[8], 8);
                sanitize_inquiry_string(&inq_result[16], 16);
                sanitize_inquiry_string(&inq_result[32], 4);

                response_len = inq_result[4] + 5;
                if (response_len > 255)
                        response_len = first_inquiry_len;       /* sanity */

                /*
                 * Get any flags for this device.
                 *
                 * XXX add a bflags to scsi_device, and replace the
                 * corresponding bit fields in scsi_device, so bflags
                 * need not be passed as an argument.
                 */
                *bflags = scsi_get_device_flags(sdev, &inq_result[8],
                                &inq_result[16]);

                /* When the first pass succeeds we gain information about
                 * what larger transfer lengths might work. */
                if (pass == 1) {
                        if (BLIST_INQUIRY_36 & *bflags)
                                next_inquiry_len = 36;
                        else if (BLIST_INQUIRY_58 & *bflags)
                                next_inquiry_len = 58;
                        else if (sdev->inquiry_len)
                                next_inquiry_len = sdev->inquiry_len;
                        else
                                next_inquiry_len = response_len;

                        /* If more data is available perform the second pass */
                        if (next_inquiry_len > try_inquiry_len) {
                                try_inquiry_len = next_inquiry_len;
                                pass = 2;
                                goto next_pass;
                        }
                }

        } else if (pass == 2) {
                printk(KERN_INFO "scsi scan: %d byte inquiry failed.  "
                                "Consider BLIST_INQUIRY_36 for this device\n",
                                try_inquiry_len);

                /* If this pass failed, the third pass goes back and transfers
                 * the same amount as we successfully got in the first pass. */
                try_inquiry_len = first_inquiry_len;
                pass = 3;
                goto next_pass;
        }

        /* If the last transfer attempt got an error, assume the
         * peripheral doesn't exist or is dead. */
        if (result)
                return -EIO;

        /* Don't report any more data than the device says is valid */
        sdev->inquiry_len = min(try_inquiry_len, response_len);

        /*
         * XXX Abort if the response length is less than 36? If less than
         * 32, the lookup of the device flags (above) could be invalid,
         * and it would be possible to take an incorrect action - we do
         * not want to hang because of a short INQUIRY. On the flip side,
         * if the device is spun down or becoming ready (and so it gives a
         * short INQUIRY), an abort here prevents any further use of the
         * device, including spin up.
         *
         * On the whole, the best approach seems to be to assume the first
         * 36 bytes are valid no matter what the device says.  That's
         * better than copying < 36 bytes to the inquiry-result buffer
         * and displaying garbage for the Vendor, Product, or Revision
         * strings.
         */
        if (sdev->inquiry_len < 36) {
                printk(KERN_INFO "scsi scan: INQUIRY result too short (%d),"
                                " using 36\n", sdev->inquiry_len);
                sdev->inquiry_len = 36;
        }

        /*
         * Related to the above issue:
         *
         * XXX Devices (disk or all?) should be sent a TEST UNIT READY,
         * and if not ready, sent a START_STOP to start (maybe spin up) and
         * then send the INQUIRY again, since the INQUIRY can change after
         * a device is initialized.
         *
         * Ideally, start a device if explicitly asked to do so.  This
         * assumes that a device is spun up on power on, spun down on
         * request, and then spun up on request.
         */

        /*
         * The scanning code needs to know the scsi_level, even if no
         * device is attached at LUN 0 (SCSI_SCAN_TARGET_PRESENT) so
         * non-zero LUNs can be scanned.
         */
        sdev->scsi_level = inq_result[2] & 0x07;
        if (sdev->scsi_level >= 2 ||
            (sdev->scsi_level == 1 && (inq_result[3] & 0x0f) == 1))
                sdev->scsi_level++;
        sdev->sdev_target->scsi_level = sdev->scsi_level;

        return 0;
}

/**
 * scsi_add_lun - allocate and fully initialze a scsi_device
 * @sdev:       holds information to be stored in the new scsi_device
 * @inq_result: holds the result of a previous INQUIRY to the LUN
 * @bflags:     black/white list flag
 * @async:      1 if this device is being scanned asynchronously
 *
 * Description:
 *     Initialize the scsi_device @sdev.  Optionally set fields based
 *     on values in *@bflags.
 *
 * Return:
 *     SCSI_SCAN_NO_RESPONSE: could not allocate or setup a scsi_device
 *     SCSI_SCAN_LUN_PRESENT: a new scsi_device was allocated and initialized
 **/
static int scsi_add_lun(struct scsi_device *sdev, unsigned char *inq_result,
                int *bflags, int async)
{
        int ret;

        /*
         * XXX do not save the inquiry, since it can change underneath us,
         * save just vendor/model/rev.
         *
         * Rather than save it and have an ioctl that retrieves the saved
         * value, have an ioctl that executes the same INQUIRY code used
         * in scsi_probe_lun, let user level programs doing INQUIRY
         * scanning run at their own risk, or supply a user level program
         * that can correctly scan.
         */

        /*
         * Copy at least 36 bytes of INQUIRY data, so that we don't
         * dereference unallocated memory when accessing the Vendor,
         * Product, and Revision strings.  Badly behaved devices may set
         * the INQUIRY Additional Length byte to a small value, indicating
         * these strings are invalid, but often they contain plausible data
         * nonetheless.  It doesn't matter if the device sent < 36 bytes
         * total, since scsi_probe_lun() initializes inq_result with 0s.
         */
        sdev->inquiry = kmemdup(inq_result,
                                max_t(size_t, sdev->inquiry_len, 36),
                                GFP_ATOMIC);
        if (sdev->inquiry == NULL)
                return SCSI_SCAN_NO_RESPONSE;

        sdev->vendor = (char *) (sdev->inquiry + 8);
        sdev->model = (char *) (sdev->inquiry + 16);
        sdev->rev = (char *) (sdev->inquiry + 32);

        if (*bflags & BLIST_ISROM) {
                sdev->type = TYPE_ROM;
                sdev->removable = 1;
        } else {
                sdev->type = (inq_result[0] & 0x1f);
                sdev->removable = (inq_result[1] & 0x80) >> 7;
        }

        switch (sdev->type) {
        case TYPE_RBC:
        case TYPE_TAPE:
        case TYPE_DISK:
        case TYPE_PRINTER:
        case TYPE_MOD:
        case TYPE_PROCESSOR:
        case TYPE_SCANNER:
        case TYPE_MEDIUM_CHANGER:
        case TYPE_ENCLOSURE:
        case TYPE_COMM:
        case TYPE_RAID:
                sdev->writeable = 1;
                break;
        case TYPE_ROM:
        case TYPE_WORM:
                sdev->writeable = 0;
                break;
        default:
                printk(KERN_INFO "scsi: unknown device type %d\n", sdev->type);
        }

        if (sdev->type == TYPE_RBC || sdev->type == TYPE_ROM) {
                /* RBC and MMC devices can return SCSI-3 compliance and yet
                 * still not support REPORT LUNS, so make them act as
                 * BLIST_NOREPORTLUN unless BLIST_REPORTLUN2 is
                 * specifically set */
                if ((*bflags & BLIST_REPORTLUN2) == 0)
                        *bflags |= BLIST_NOREPORTLUN;
        }

        /*
         * For a peripheral qualifier (PQ) value of 1 (001b), the SCSI
         * spec says: The device server is capable of supporting the
         * specified peripheral device type on this logical unit. However,
         * the physical device is not currently connected to this logical
         * unit.
         *
         * The above is vague, as it implies that we could treat 001 and
         * 011 the same. Stay compatible with previous code, and create a
         * scsi_device for a PQ of 1
         *
         * Don't set the device offline here; rather let the upper
         * level drivers eval the PQ to decide whether they should
         * attach. So remove ((inq_result[0] >> 5) & 7) == 1 check.
         */ 

        sdev->inq_periph_qual = (inq_result[0] >> 5) & 7;
        sdev->lockable = sdev->removable;
        sdev->soft_reset = (inq_result[7] & 1) && ((inq_result[3] & 7) == 2);

        if (sdev->scsi_level >= SCSI_3 ||
                        (sdev->inquiry_len > 56 && inq_result[56] & 0x04))
                sdev->ppr = 1;
        if (inq_result[7] & 0x60)
                sdev->wdtr = 1;
        if (inq_result[7] & 0x10)
                sdev->sdtr = 1;

        sdev_printk(KERN_NOTICE, sdev, "%s %.8s %.16s %.4s PQ: %d "
                        "ANSI: %d%s\n", scsi_device_type(sdev->type),
                        sdev->vendor, sdev->model, sdev->rev,
                        sdev->inq_periph_qual, inq_result[2] & 0x07,
                        (inq_result[3] & 0x0f) == 1 ? " CCS" : "");

        if ((sdev->scsi_level >= SCSI_2) && (inq_result[7] & 2) &&
            !(*bflags & BLIST_NOTQ))
                sdev->tagged_supported = 1;

        /*
         * Some devices (Texel CD ROM drives) have handshaking problems
         * when used with the Seagate controllers. borken is initialized
         * to 1, and then set it to 0 here.
         */
        if ((*bflags & BLIST_BORKEN) == 0)
                sdev->borken = 0;

        if (*bflags & BLIST_NO_ULD_ATTACH)
                sdev->no_uld_attach = 1;

        /*
         * Apparently some really broken devices (contrary to the SCSI
         * standards) need to be selected without asserting ATN
         */
        if (*bflags & BLIST_SELECT_NO_ATN)
                sdev->select_no_atn = 1;

        /*
         * Maximum 512 sector transfer length
         * broken RA4x00 Compaq Disk Array
         */
        if (*bflags & BLIST_MAX_512)
                blk_queue_max_sectors(sdev->request_queue, 512);

        /*
         * Some devices may not want to have a start command automatically
         * issued when a device is added.
         */
        if (*bflags & BLIST_NOSTARTONADD)
                sdev->no_start_on_add = 1;

        if (*bflags & BLIST_SINGLELUN)
                scsi_target(sdev)->single_lun = 1;

        sdev->use_10_for_rw = 1;

        if (*bflags & BLIST_MS_SKIP_PAGE_08)
                sdev->skip_ms_page_8 = 1;

        if (*bflags & BLIST_MS_SKIP_PAGE_3F)
                sdev->skip_ms_page_3f = 1;

        if (*bflags & BLIST_USE_10_BYTE_MS)
                sdev->use_10_for_ms = 1;

        /* set the device running here so that slave configure
         * may do I/O */
        ret = scsi_device_set_state(sdev, SDEV_RUNNING);
        if (ret) {
                ret = scsi_device_set_state(sdev, SDEV_BLOCK);

                if (ret) {
                        sdev_printk(KERN_ERR, sdev,
                                    "in wrong state %s to complete scan\n",
                                    scsi_device_state_name(sdev->sdev_state));
                        return SCSI_SCAN_NO_RESPONSE;
                }
        }

        if (*bflags & BLIST_MS_192_BYTES_FOR_3F)
                sdev->use_192_bytes_for_3f = 1;

        if (*bflags & BLIST_NOT_LOCKABLE)
                sdev->lockable = 0;

        if (*bflags & BLIST_RETRY_HWERROR)
                sdev->retry_hwerror = 1;

        transport_configure_device(&sdev->sdev_gendev);

        if (sdev->host->hostt->slave_configure) {
                ret = sdev->host->hostt->slave_configure(sdev);
                if (ret) {
                        /*
                         * if LLDD reports slave not present, don't clutter
                         * console with alloc failure messages
                         */
                        if (ret != -ENXIO) {
                                sdev_printk(KERN_ERR, sdev,
                                        "failed to configure device\n");
                        }
                        return SCSI_SCAN_NO_RESPONSE;
                }
        }

        /*
         * Ok, the device is now all set up, we can
         * register it and tell the rest of the kernel
         * about it.
         */
        if (!async && scsi_sysfs_add_sdev(sdev) != 0)
                return SCSI_SCAN_NO_RESPONSE;

        return SCSI_SCAN_LUN_PRESENT;
}

static inline void scsi_destroy_sdev(struct scsi_device *sdev)
{
        scsi_device_set_state(sdev, SDEV_DEL);
        if (sdev->host->hostt->slave_destroy)
                sdev->host->hostt->slave_destroy(sdev);
        transport_destroy_device(&sdev->sdev_gendev);
        put_device(&sdev->sdev_gendev);
}

#ifdef CONFIG_SCSI_LOGGING
/** 
 * scsi_inq_str - print INQUIRY data from min to max index, strip trailing whitespace
 * @buf:   Output buffer with at least end-first+1 bytes of space
 * @inq:   Inquiry buffer (input)
 * @first: Offset of string into inq
 * @end:   Index after last character in inq
 */
static unsigned char *scsi_inq_str(unsigned char *buf, unsigned char *inq,
                                   unsigned first, unsigned end)
{
        unsigned term = 0, idx;

        for (idx = 0; idx + first < end && idx + first < inq[4] + 5; idx++) {
                if (inq[idx+first] > ' ') {
                        buf[idx] = inq[idx+first];
                        term = idx+1;
                } else {
                        buf[idx] = ' ';
                }
        }
        buf[term] = 0;
        return buf;
}
#endif

/**
 * scsi_probe_and_add_lun - probe a LUN, if a LUN is found add it
 * @starget:    pointer to target device structure
 * @lun:        LUN of target device
 * @bflagsp:    store bflags here if not NULL
 * @sdevp:      probe the LUN corresponding to this scsi_device
 * @rescan:     if nonzero skip some code only needed on first scan
 * @hostdata:   passed to scsi_alloc_sdev()
 *
 * Description:
 *     Call scsi_probe_lun, if a LUN with an attached device is found,
 *     allocate and set it up by calling scsi_add_lun.
 *
 * Return:
 *     SCSI_SCAN_NO_RESPONSE: could not allocate or setup a scsi_device
 *     SCSI_SCAN_TARGET_PRESENT: target responded, but no device is
 *         attached at the LUN
 *     SCSI_SCAN_LUN_PRESENT: a new scsi_device was allocated and initialized
 **/
static int scsi_probe_and_add_lun(struct scsi_target *starget,
                                  uint lun, int *bflagsp,
                                  struct scsi_device **sdevp, int rescan,
                                  void *hostdata)
{
        struct scsi_device *sdev;
        unsigned char *result;
        int bflags, res = SCSI_SCAN_NO_RESPONSE, result_len = 256;
        struct Scsi_Host *shost = dev_to_shost(starget->dev.parent);

        /*
         * The rescan flag is used as an optimization, the first scan of a
         * host adapter calls into here with rescan == 0.
         */
        sdev = scsi_device_lookup_by_target(starget, lun);
        if (sdev) {
                if (rescan || !scsi_device_created(sdev)) {
                        SCSI_LOG_SCAN_BUS(3, printk(KERN_INFO
                                "scsi scan: device exists on %s\n",
                                sdev->sdev_gendev.bus_id));
                        if (sdevp)
                                *sdevp = sdev;
                        else
                                scsi_device_put(sdev);

                        if (bflagsp)
                                *bflagsp = scsi_get_device_flags(sdev,
                                                                 sdev->vendor,
                                                                 sdev->model);
                        return SCSI_SCAN_LUN_PRESENT;
                }
                scsi_device_put(sdev);
        } else
                sdev = scsi_alloc_sdev(starget, lun, hostdata);
        if (!sdev)
                goto out;

        result = kmalloc(result_len, GFP_ATOMIC |
                        ((shost->unchecked_isa_dma) ? __GFP_DMA : 0));
        if (!result)
                goto out_free_sdev;

        if (scsi_probe_lun(sdev, result, result_len, &bflags))
                goto out_free_result;

        if (bflagsp)
                *bflagsp = bflags;
        /*
         * result contains valid SCSI INQUIRY data.
         */
        if (((result[0] >> 5) == 3) && !(bflags & BLIST_ATTACH_PQ3)) {
                /*
                 * For a Peripheral qualifier 3 (011b), the SCSI
                 * spec says: The device server is not capable of
                 * supporting a physical device on this logical
                 * unit.
                 *
                 * For disks, this implies that there is no
                 * logical disk configured at sdev->lun, but there
                 * is a target id responding.
                 */
                SCSI_LOG_SCAN_BUS(2, sdev_printk(KERN_INFO, sdev, "scsi scan:"
                                   " peripheral qualifier of 3, device not"
                                   " added\n"))
                if (lun == 0) {
                        SCSI_LOG_SCAN_BUS(1, {
                                unsigned char vend[9];
                                unsigned char mod[17];

                                sdev_printk(KERN_INFO, sdev,
                                        "scsi scan: consider passing scsi_mod."
                                        "dev_flags=%s:%s:0x240 or 0x1000240\n",
                                        scsi_inq_str(vend, result, 8, 16),
                                        scsi_inq_str(mod, result, 16, 32));
                        });

                }

                res = SCSI_SCAN_TARGET_PRESENT;
                goto out_free_result;
        }

        /*
         * Some targets may set slight variations of PQ and PDT to signal
         * that no LUN is present, so don't add sdev in these cases.
         * Two specific examples are:
         * 1) NetApp targets: return PQ=1, PDT=0x1f
         * 2) USB UFI: returns PDT=0x1f, with the PQ bits being "reserved"
         *    in the UFI 1.0 spec (we cannot rely on reserved bits).
         *
         * References:
         * 1) SCSI SPC-3, pp. 145-146
         * PQ=1: "A peripheral device having the specified peripheral
         * device type is not connected to this logical unit. However, the
         * device server is capable of supporting the specified peripheral
         * device type on this logical unit."
         * PDT=0x1f: "Unknown or no device type"
         * 2) USB UFI 1.0, p. 20
         * PDT=00h Direct-access device (floppy)
         * PDT=1Fh none (no FDD connected to the requested logical unit)
         */
        if (((result[0] >> 5) == 1 || starget->pdt_1f_for_no_lun) &&
            (result[0] & 0x1f) == 0x1f &&
            !scsi_is_wlun(lun)) {
                SCSI_LOG_SCAN_BUS(3, printk(KERN_INFO
                                        "scsi scan: peripheral device type"
                                        " of 31, no device added\n"));
                res = SCSI_SCAN_TARGET_PRESENT;
                goto out_free_result;
        }

        res = scsi_add_lun(sdev, result, &bflags, shost->async_scan);
        if (res == SCSI_SCAN_LUN_PRESENT) {
                if (bflags & BLIST_KEY) {
                        sdev->lockable = 0;
                        scsi_unlock_floptical(sdev, result);
                }
        }

 out_free_result:
        kfree(result);
 out_free_sdev:
        if (res == SCSI_SCAN_LUN_PRESENT) {
                if (sdevp) {
                        if (scsi_device_get(sdev) == 0) {
                                *sdevp = sdev;
                        } else {
                                __scsi_remove_device(sdev);
                                res = SCSI_SCAN_NO_RESPONSE;
                        }
                }
        } else
                scsi_destroy_sdev(sdev);
 out:
        return res;
}

/**
 * scsi_sequential_lun_scan - sequentially scan a SCSI target
 * @starget:    pointer to target structure to scan
 * @bflags:     black/white list flag for LUN 0
 * @scsi_level: Which version of the standard does this device adhere to
 * @rescan:     passed to scsi_probe_add_lun()
 *
 * Description:
 *     Generally, scan from LUN 1 (LUN 0 is assumed to already have been
 *     scanned) to some maximum lun until a LUN is found with no device
 *     attached. Use the bflags to figure out any oddities.
 *
 *     Modifies sdevscan->lun.
 **/
static void scsi_sequential_lun_scan(struct scsi_target *starget,
                                     int bflags, int scsi_level, int rescan)
{
        unsigned int sparse_lun, lun, max_dev_lun;
        struct Scsi_Host *shost = dev_to_shost(starget->dev.parent);

        SCSI_LOG_SCAN_BUS(3, printk(KERN_INFO "scsi scan: Sequential scan of"
                                    "%s\n", starget->dev.bus_id));

        max_dev_lun = min(max_scsi_luns, shost->max_lun);
        /*
         * If this device is known to support sparse multiple units,
         * override the other settings, and scan all of them. Normally,
         * SCSI-3 devices should be scanned via the REPORT LUNS.
         */
        if (bflags & BLIST_SPARSELUN) {
                max_dev_lun = shost->max_lun;
                sparse_lun = 1;
        } else
                sparse_lun = 0;

        /*
         * If less than SCSI_1_CSS, and no special lun scaning, stop
         * scanning; this matches 2.4 behaviour, but could just be a bug
         * (to continue scanning a SCSI_1_CSS device).
         *
         * This test is broken.  We might not have any device on lun0 for
         * a sparselun device, and if that's the case then how would we
         * know the real scsi_level, eh?  It might make sense to just not
         * scan any SCSI_1 device for non-0 luns, but that check would best
         * go into scsi_alloc_sdev() and just have it return null when asked
         * to alloc an sdev for lun > 0 on an already found SCSI_1 device.
         *
        if ((sdevscan->scsi_level < SCSI_1_CCS) &&
            ((bflags & (BLIST_FORCELUN | BLIST_SPARSELUN | BLIST_MAX5LUN))
             == 0))
                return;
         */
        /*
         * If this device is known to support multiple units, override
         * the other settings, and scan all of them.
         */
        if (bflags & BLIST_FORCELUN)
                max_dev_lun = shost->max_lun;
        /*
         * REGAL CDC-4X: avoid hang after LUN 4
         */
        if (bflags & BLIST_MAX5LUN)
                max_dev_lun = min(5U, max_dev_lun);
        /*
         * Do not scan SCSI-2 or lower device past LUN 7, unless
         * BLIST_LARGELUN.
         */
        if (scsi_level < SCSI_3 && !(bflags & BLIST_LARGELUN))
                max_dev_lun = min(8U, max_dev_lun);

        /*
         * We have already scanned LUN 0, so start at LUN 1. Keep scanning
         * until we reach the max, or no LUN is found and we are not
         * sparse_lun.
         */
        for (lun = 1; lun < max_dev_lun; ++lun)
                if ((scsi_probe_and_add_lun(starget, lun, NULL, NULL, rescan,
                                            NULL) != SCSI_SCAN_LUN_PRESENT) &&
                    !sparse_lun)
                        return;
}

/**
 * scsilun_to_int: convert a scsi_lun to an int
 * @scsilun:    struct scsi_lun to be converted.
 *
 * Description:
 *     Convert @scsilun from a struct scsi_lun to a four byte host byte-ordered
 *     integer, and return the result. The caller must check for
 *     truncation before using this function.
 *
 * Notes:
 *     The struct scsi_lun is assumed to be four levels, with each level
 *     effectively containing a SCSI byte-ordered (big endian) short; the
 *     addressing bits of each level are ignored (the highest two bits).
 *     For a description of the LUN format, post SCSI-3 see the SCSI
 *     Architecture Model, for SCSI-3 see the SCSI Controller Commands.
 *
 *     Given a struct scsi_lun of: 0a 04 0b 03 00 00 00 00, this function returns
 *     the integer: 0x0b030a04
 **/
int scsilun_to_int(struct scsi_lun *scsilun)
{
        int i;
        unsigned int lun;

        lun = 0;
        for (i = 0; i < sizeof(lun); i += 2)
                lun = lun | (((scsilun->scsi_lun[i] << 8) |
                              scsilun->scsi_lun[i + 1]) << (i * 8));
        return lun;
}
EXPORT_SYMBOL(scsilun_to_int);

/**
 * int_to_scsilun: reverts an int into a scsi_lun
 * @lun:        integer to be reverted
 * @scsilun:    struct scsi_lun to be set.
 *
 * Description:
 *     Reverts the functionality of the scsilun_to_int, which packed
 *     an 8-byte lun value into an int. This routine unpacks the int
 *     back into the lun value.
 *     Note: the scsilun_to_int() routine does not truly handle all
 *     8bytes of the lun value. This functions restores only as much
 *     as was set by the routine.
 *
 * Notes:
 *     Given an integer : 0x0b030a04,  this function returns a
 *     scsi_lun of : struct scsi_lun of: 0a 04 0b 03 00 00 00 00
 *
 **/
void int_to_scsilun(unsigned int lun, struct scsi_lun *scsilun)
{
        int i;

        memset(scsilun->scsi_lun, 0, sizeof(scsilun->scsi_lun));

        for (i = 0; i < sizeof(lun); i += 2) {
                scsilun->scsi_lun[i] = (lun >> 8) & 0xFF;
                scsilun->scsi_lun[i+1] = lun & 0xFF;
                lun = lun >> 16;
        }
}
EXPORT_SYMBOL(int_to_scsilun);

/**
 * scsi_report_lun_scan - Scan using SCSI REPORT LUN results
 * @starget: which target
 * @bflags: Zero or a mix of BLIST_NOLUN, BLIST_REPORTLUN2, or BLIST_NOREPORTLUN
 * @rescan: nonzero if we can skip code only needed on first scan
 *
 * Description:
 *   Fast scanning for modern (SCSI-3) devices by sending a REPORT LUN command.
 *   Scan the resulting list of LUNs by calling scsi_probe_and_add_lun.
 *
 *   If BLINK_REPORTLUN2 is set, scan a target that supports more than 8
 *   LUNs even if it's older than SCSI-3.
 *   If BLIST_NOREPORTLUN is set, return 1 always.
 *   If BLIST_NOLUN is set, return 0 always.
 *
 * Return:
 *     0: scan completed (or no memory, so further scanning is futile)
 *     1: could not scan with REPORT LUN
 **/
static int scsi_report_lun_scan(struct scsi_target *starget, int bflags,
                                int rescan)
{
        char devname[64];
        unsigned char scsi_cmd[MAX_COMMAND_SIZE];
        unsigned int length;
        unsigned int lun;
        unsigned int num_luns;
        unsigned int retries;
        int result;
        struct scsi_lun *lunp, *lun_data;
        u8 *data;
        struct scsi_sense_hdr sshdr;
        struct scsi_device *sdev;
        struct Scsi_Host *shost = dev_to_shost(&starget->dev);
        int ret = 0;

        /*
         * Only support SCSI-3 and up devices if BLIST_NOREPORTLUN is not set.
         * Also allow SCSI-2 if BLIST_REPORTLUN2 is set and host adapter does
         * support more than 8 LUNs.
         */
        if (bflags & BLIST_NOREPORTLUN)
                return 1;
        if (starget->scsi_level < SCSI_2 &&
            starget->scsi_level != SCSI_UNKNOWN)
                return 1;
        if (starget->scsi_level < SCSI_3 &&
            (!(bflags & BLIST_REPORTLUN2) || shost->max_lun <= 8))
                return 1;
        if (bflags & BLIST_NOLUN)
                return 0;

        if (!(sdev = scsi_device_lookup_by_target(starget, 0))) {
                sdev = scsi_alloc_sdev(starget, 0, NULL);
                if (!sdev)
                        return 0;
                if (scsi_device_get(sdev))
                        return 0;
        }

        sprintf(devname, "host %d channel %d id %d",
                shost->host_no, sdev->channel, sdev->id);

        /*
         * Allocate enough to hold the header (the same size as one scsi_lun)
         * plus the max number of luns we are requesting.
         *
         * Reallocating and trying again (with the exact amount we need)
         * would be nice, but then we need to somehow limit the size
         * allocated based on the available memory and the limits of
         * kmalloc - we don't want a kmalloc() failure of a huge value to
         * prevent us from finding any LUNs on this target.
         */
        length = (max_scsi_report_luns + 1) * sizeof(struct scsi_lun);
        lun_data = kmalloc(length, GFP_ATOMIC |
                           (sdev->host->unchecked_isa_dma ? __GFP_DMA : 0));
        if (!lun_data) {
                printk(ALLOC_FAILURE_MSG, __func__);
                goto out;
        }

        scsi_cmd[0] = REPORT_LUNS;

        /*
         * bytes 1 - 5: reserved, set to zero.
         */
        memset(&scsi_cmd[1], 0, 5);

        /*
         * bytes 6 - 9: length of the command.
         */
        scsi_cmd[6] = (unsigned char) (length >> 24) & 0xff;
        scsi_cmd[7] = (unsigned char) (length >> 16) & 0xff;
        scsi_cmd[8] = (unsigned char) (length >> 8) & 0xff;
        scsi_cmd[9] = (unsigned char) length & 0xff;

        scsi_cmd[10] = 0;       /* reserved */
        scsi_cmd[11] = 0;       /* control */

        /*
         * We can get a UNIT ATTENTION, for example a power on/reset, so
         * retry a few times (like sd.c does for TEST UNIT READY).
         * Experience shows some combinations of adapter/devices get at
         * least two power on/resets.
         *
         * Illegal requests (for devices that do not support REPORT LUNS)
         * should come through as a check condition, and will not generate
         * a retry.
         */
        for (retries = 0; retries < 3; retries++) {
                SCSI_LOG_SCAN_BUS(3, printk (KERN_INFO "scsi scan: Sending"
                                " REPORT LUNS to %s (try %d)\n", devname,
                                retries));

                result = scsi_execute_req(sdev, scsi_cmd, DMA_FROM_DEVICE,
                                          lun_data, length, &sshdr,
                                          SCSI_TIMEOUT + 4 * HZ, 3);

                SCSI_LOG_SCAN_BUS(3, printk (KERN_INFO "scsi scan: REPORT LUNS"
                                " %s (try %d) result 0x%x\n", result
                                ?  "failed" : "successful", retries, result));
                if (result == 0)
                        break;
                else if (scsi_sense_valid(&sshdr)) {
                        if (sshdr.sense_key != UNIT_ATTENTION)
                                break;
                }
        }

        if (result) {
                /*
                 * The device probably does not support a REPORT LUN command
                 */
                ret = 1;
                goto out_err;
        }

        /*
         * Get the length from the first four bytes of lun_data.
         */
        data = (u8 *) lun_data->scsi_lun;
        length = ((data[0] << 24) | (data[1] << 16) |
                  (data[2] << 8) | (data[3] << 0));

        num_luns = (length / sizeof(struct scsi_lun));
        if (num_luns > max_scsi_report_luns) {
                printk(KERN_WARNING "scsi: On %s only %d (max_scsi_report_luns)"
                       " of %d luns reported, try increasing"
                       " max_scsi_report_luns.\n", devname,
                       max_scsi_report_luns, num_luns);
                num_luns = max_scsi_report_luns;
        }

        SCSI_LOG_SCAN_BUS(3, sdev_printk (KERN_INFO, sdev,
                "scsi scan: REPORT LUN scan\n"));

        /*
         * Scan the luns in lun_data. The entry at offset 0 is really
         * the header, so start at 1 and go up to and including num_luns.
         */
        for (lunp = &lun_data[1]; lunp <= &lun_data[num_luns]; lunp++) {
                lun = scsilun_to_int(lunp);

                /*
                 * Check if the unused part of lunp is non-zero, and so
                 * does not fit in lun.
                 */
                if (memcmp(&lunp->scsi_lun[sizeof(lun)], "\0\0\0\0", 4)) {
                        int i;

                        /*
                         * Output an error displaying the LUN in byte order,
                         * this differs from what linux would print for the
                         * integer LUN value.
                         */
                        printk(KERN_WARNING "scsi: %s lun 0x", devname);
                        data = (char *)lunp->scsi_lun;
                        for (i = 0; i < sizeof(struct scsi_lun); i++)
                                printk("%02x", data[i]);
                        printk(" has a LUN larger than currently supported.\n");
                } else if (lun > sdev->host->max_lun) {
                        printk(KERN_WARNING "scsi: %s lun%d has a LUN larger"
                               " than allowed by the host adapter\n",
                               devname, lun);
                } else {
                        int res;

                        res = scsi_probe_and_add_lun(starget,
                                lun, NULL, NULL, rescan, NULL);
                        if (res == SCSI_SCAN_NO_RESPONSE) {
                                /*
                                 * Got some results, but now none, abort.
                                 */
                                sdev_printk(KERN_ERR, sdev,
                                        "Unexpected response"
                                        " from lun %d while scanning, scan"
                                        " aborted\n", lun);
                                break;
                        }
                }
        }

 out_err:
        kfree(lun_data);
 out:
        scsi_device_put(sdev);
        if (scsi_device_created(sdev))
                /*
                 * the sdev we used didn't appear in the report luns scan
                 */
                scsi_destroy_sdev(sdev);
        return ret;
}

struct scsi_device *__scsi_add_device(struct Scsi_Host *shost, uint channel,
                                      uint id, uint lun, void *hostdata)
{
        struct scsi_device *sdev = ERR_PTR(-ENODEV);
        struct device *parent = &shost->shost_gendev;
        struct scsi_target *starget;

        if (strncmp(scsi_scan_type, "none", 4) == 0)
                return ERR_PTR(-ENODEV);

        starget = scsi_alloc_target(parent, channel, id);
        if (!starget)
                return ERR_PTR(-ENOMEM);

        mutex_lock(&shost->scan_mutex);
        if (!shost->async_scan)
                scsi_complete_async_scans();

        if (scsi_host_scan_allowed(shost))
                scsi_probe_and_add_lun(starget, lun, NULL, &sdev, 1, hostdata);
        mutex_unlock(&shost->scan_mutex);
        scsi_target_reap(starget);
        put_device(&starget->dev);

        return sdev;
}
EXPORT_SYMBOL(__scsi_add_device);

int scsi_add_device(struct Scsi_Host *host, uint channel,
                    uint target, uint lun)
{
        struct scsi_device *sdev = 
                __scsi_add_device(host, channel, target, lun, NULL);
        if (IS_ERR(sdev))
                return PTR_ERR(sdev);

        scsi_device_put(sdev);
        return 0;
}
EXPORT_SYMBOL(scsi_add_device);

void scsi_rescan_device(struct device *dev)
{
        struct scsi_driver *drv;
        
        if (!dev->driver)
                return;

        drv = to_scsi_driver(dev->driver);
        if (try_module_get(drv->owner)) {
                if (drv->rescan)
                        drv->rescan(dev);
                module_put(drv->owner);
        }
}
EXPORT_SYMBOL(scsi_rescan_device);

static void __scsi_scan_target(struct device *parent, unsigned int channel,
                unsigned int id, unsigned int lun, int rescan)
{
        struct Scsi_Host *shost = dev_to_shost(parent);
        int bflags = 0;
        int res;
        struct scsi_target *starget;

        if (shost->this_id == id)
                /*
                 * Don't scan the host adapter
                 */
                return;

        starget = scsi_alloc_target(parent, channel, id);
        if (!starget)
                return;

        if (lun != SCAN_WILD_CARD) {
                /*
                 * Scan for a specific host/chan/id/lun.
                 */
                scsi_probe_and_add_lun(starget, lun, NULL, NULL, rescan, NULL);
                goto out_reap;
        }

        /*
         * Scan LUN 0, if there is some response, scan further. Ideally, we
         * would not configure LUN 0 until all LUNs are scanned.
         */
        res = scsi_probe_and_add_lun(starget, 0, &bflags, NULL, rescan, NULL);
        if (res == SCSI_SCAN_LUN_PRESENT || res == SCSI_SCAN_TARGET_PRESENT) {
                if (scsi_report_lun_scan(starget, bflags, rescan) != 0)
                        /*
                         * The REPORT LUN did not scan the target,
                         * do a sequential scan.
                         */
                        scsi_sequential_lun_scan(starget, bflags,
                                                 starget->scsi_level, rescan);
        }

 out_reap:
        /* now determine if the target has any children at all
         * and if not, nuke it */
        scsi_target_reap(starget);

        put_device(&starget->dev);
}

/**
 * scsi_scan_target - scan a target id, possibly including all LUNs on the target.
 * @parent:     host to scan
 * @channel:    channel to scan
 * @id:         target id to scan
 * @lun:        Specific LUN to scan or SCAN_WILD_CARD
 * @rescan:     passed to LUN scanning routines
 *
 * Description:
 *     Scan the target id on @parent, @channel, and @id. Scan at least LUN 0,
 *     and possibly all LUNs on the target id.
 *
 *     First try a REPORT LUN scan, if that does not scan the target, do a
 *     sequential scan of LUNs on the target id.
 **/
void scsi_scan_target(struct device *parent, unsigned int channel,
                      unsigned int id, unsigned int lun, int rescan)
{
        struct Scsi_Host *shost = dev_to_shost(parent);

        if (strncmp(scsi_scan_type, "none", 4) == 0)
                return;

        mutex_lock(&shost->scan_mutex);
        if (!shost->async_scan)
                scsi_complete_async_scans();

        if (scsi_host_scan_allowed(shost))
                __scsi_scan_target(parent, channel, id, lun, rescan);
        mutex_unlock(&shost->scan_mutex);
}
EXPORT_SYMBOL(scsi_scan_target);

static void scsi_scan_channel(struct Scsi_Host *shost, unsigned int channel,
                              unsigned int id, unsigned int lun, int rescan)
{
        uint order_id;

        if (id == SCAN_WILD_CARD)
                for (id = 0; id < shost->max_id; ++id) {
                        /*
                         * XXX adapter drivers when possible (FCP, iSCSI)
                         * could modify max_id to match the current max,
                         * not the absolute max.
                         *
                         * XXX add a shost id iterator, so for example,
                         * the FC ID can be the same as a target id
                         * without a huge overhead of sparse id's.
                         */
                        if (shost->reverse_ordering)
                                /*
                                 * Scan from high to low id.
                                 */
                                order_id = shost->max_id - id - 1;
                        else
                                order_id = id;
                        __scsi_scan_target(&shost->shost_gendev, channel,
                                        order_id, lun, rescan);
                }
        else
                __scsi_scan_target(&shost->shost_gendev, channel,
                                id, lun, rescan);
}

int scsi_scan_host_selected(struct Scsi_Host *shost, unsigned int channel,
                            unsigned int id, unsigned int lun, int rescan)
{
        SCSI_LOG_SCAN_BUS(3, shost_printk (KERN_INFO, shost,
                "%s: <%u:%u:%u>\n",
                __func__, channel, id, lun));

        if (((channel != SCAN_WILD_CARD) && (channel > shost->max_channel)) ||
            ((id != SCAN_WILD_CARD) && (id >= shost->max_id)) ||
            ((lun != SCAN_WILD_CARD) && (lun > shost->max_lun)))
                return -EINVAL;

        mutex_lock(&shost->scan_mutex);
        if (!shost->async_scan)
                scsi_complete_async_scans();

        if (scsi_host_scan_allowed(shost)) {
                if (channel == SCAN_WILD_CARD)
                        for (channel = 0; channel <= shost->max_channel;
                             channel++)
                                scsi_scan_channel(shost, channel, id, lun,
                                                  rescan);
                else
                        scsi_scan_channel(shost, channel, id, lun, rescan);
        }
        mutex_unlock(&shost->scan_mutex);

        return 0;
}

static void scsi_sysfs_add_devices(struct Scsi_Host *shost)
{
        struct scsi_device *sdev;
        shost_for_each_device(sdev, shost) {
                if (!scsi_host_scan_allowed(shost) ||
                    scsi_sysfs_add_sdev(sdev) != 0)
                        scsi_destroy_sdev(sdev);
        }
}

/**
 * scsi_prep_async_scan - prepare for an async scan
 * @shost: the host which will be scanned
 * Returns: a cookie to be passed to scsi_finish_async_scan()
 *
 * Tells the midlayer this host is going to do an asynchronous scan.
 * It reserves the host's position in the scanning list and ensures
 * that other asynchronous scans started after this one won't affect the
 * ordering of the discovered devices.
 */
static struct async_scan_data *scsi_prep_async_scan(struct Scsi_Host *shost)
{
        struct async_scan_data *data;
        unsigned long flags;

        if (strncmp(scsi_scan_type, "sync", 4) == 0)
                return NULL;

        if (shost->async_scan) {
                printk("%s called twice for host %d", __func__,
                                shost->host_no);
                dump_stack();
                return NULL;
        }

        data = kmalloc(sizeof(*data), GFP_KERNEL);
        if (!data)
                goto err;
        data->shost = scsi_host_get(shost);
        if (!data->shost)
                goto err;
        init_completion(&data->prev_finished);

        mutex_lock(&shost->scan_mutex);
        spin_lock_irqsave(shost->host_lock, flags);
        shost->async_scan = 1;
        spin_unlock_irqrestore(shost->host_lock, flags);
        mutex_unlock(&shost->scan_mutex);

        spin_lock(&async_scan_lock);
        if (list_empty(&scanning_hosts))
                complete(&data->prev_finished);
        list_add_tail(&data->list, &scanning_hosts);
        spin_unlock(&async_scan_lock);

        return data;

 err:
        kfree(data);
        return NULL;
}

/**
 * scsi_finish_async_scan - asynchronous scan has finished
 * @data: cookie returned from earlier call to scsi_prep_async_scan()
 *
 * All the devices currently attached to this host have been found.
 * This function announces all the devices it has found to the rest
 * of the system.
 */
static void scsi_finish_async_scan(struct async_scan_data *data)
{
        struct Scsi_Host *shost;
        unsigned long flags;

        if (!data)
                return;

        shost = data->shost;

        mutex_lock(&shost->scan_mutex);

        if (!shost->async_scan) {
                printk("%s called twice for host %d", __func__,
                                shost->host_no);
                dump_stack();
                mutex_unlock(&shost->scan_mutex);
                return;
        }

        wait_for_completion(&data->prev_finished);

        scsi_sysfs_add_devices(shost);

        spin_lock_irqsave(shost->host_lock, flags);
        shost->async_scan = 0;
        spin_unlock_irqrestore(shost->host_lock, flags);

        mutex_unlock(&shost->scan_mutex);

        spin_lock(&async_scan_lock);
        list_del(&data->list);
        if (!list_empty(&scanning_hosts)) {
                struct async_scan_data *next = list_entry(scanning_hosts.next,
                                struct async_scan_data, list);
                complete(&next->prev_finished);
        }
        spin_unlock(&async_scan_lock);

        scsi_host_put(shost);
        kfree(data);
}

static void do_scsi_scan_host(struct Scsi_Host *shost)
{
        if (shost->hostt->scan_finished) {
                unsigned long start = jiffies;
                if (shost->hostt->scan_start)
                        shost->hostt->scan_start(shost);

                while (!shost->hostt->scan_finished(shost, jiffies - start))
                        msleep(10);
        } else {
                scsi_scan_host_selected(shost, SCAN_WILD_CARD, SCAN_WILD_CARD,
                                SCAN_WILD_CARD, 0);
        }
}

static int do_scan_async(void *_data)
{
        struct async_scan_data *data = _data;
        do_scsi_scan_host(data->shost);
        scsi_finish_async_scan(data);
        return 0;
}

/**
 * scsi_scan_host - scan the given adapter
 * @shost:      adapter to scan
 **/
void scsi_scan_host(struct Scsi_Host *shost)
{
        struct task_struct *p;
        struct async_scan_data *data;

        if (strncmp(scsi_scan_type, "none", 4) == 0)
                return;

        data = scsi_prep_async_scan(shost);
        if (!data) {
                do_scsi_scan_host(shost);
                return;
        }

        p = kthread_run(do_scan_async, data, "scsi_scan_%d", shost->host_no);
        if (IS_ERR(p))
                do_scan_async(data);
}
EXPORT_SYMBOL(scsi_scan_host);

void scsi_forget_host(struct Scsi_Host *shost)
{
        struct scsi_device *sdev;
        unsigned long flags;

 restart:
        spin_lock_irqsave(shost->host_lock, flags);
        list_for_each_entry(sdev, &shost->__devices, siblings) {
                if (sdev->sdev_state == SDEV_DEL)
                        continue;
                spin_unlock_irqrestore(shost->host_lock, flags);
                __scsi_remove_device(sdev);
                goto restart;
        }
        spin_unlock_irqrestore(shost->host_lock, flags);
}

/*
 * Function:    scsi_get_host_dev()
 *
 * Purpose:     Create a scsi_device that points to the host adapter itself.
 *
 * Arguments:   SHpnt   - Host that needs a scsi_device
 *
 * Lock status: None assumed.
 *
 * Returns:     The scsi_device or NULL
 *
 * Notes:
 *      Attach a single scsi_device to the Scsi_Host - this should
 *      be made to look like a "pseudo-device" that points to the
 *      HA itself.
 *
 *      Note - this device is not accessible from any high-level
 *      drivers (including generics), which is probably not
 *      optimal.  We can add hooks later to attach 
 */
struct scsi_device *scsi_get_host_dev(struct Scsi_Host *shost)
{
        struct scsi_device *sdev = NULL;
        struct scsi_target *starget;

        mutex_lock(&shost->scan_mutex);
        if (!scsi_host_scan_allowed(shost))
                goto out;
        starget = scsi_alloc_target(&shost->shost_gendev, 0, shost->this_id);
        if (!starget)
                goto out;

        sdev = scsi_alloc_sdev(starget, 0, NULL);
        if (sdev) {
                sdev->sdev_gendev.parent = get_device(&starget->dev);
                sdev->borken = 0;
        } else
                scsi_target_reap(starget);
        put_device(&starget->dev);
 out:
        mutex_unlock(&shost->scan_mutex);
        return sdev;
}
EXPORT_SYMBOL(scsi_get_host_dev);

/*
 * Function:    scsi_free_host_dev()
 *
 * Purpose:     Free a scsi_device that points to the host adapter itself.
 *
 * Arguments:   SHpnt   - Host that needs a scsi_device
 *
 * Lock status: None assumed.
 *
 * Returns:     Nothing
 *
 * Notes:
 */
void scsi_free_host_dev(struct scsi_device *sdev)
{
        BUG_ON(sdev->id != sdev->host->this_id);

        scsi_destroy_sdev(sdev);
}
EXPORT_SYMBOL(scsi_free_host_dev);