1 # drivers/sound/Config.in
3 # 18 Apr 1998, Michael Elizabeth Chastain, <mailto:mec@shout.net>
4 # More hacking for modularisation.
6 # Prompt user for primary drivers.
8 config SOUND_BCM_CS4297A
9 tristate "Crystal Sound CS4297a (for Swarm)"
10 depends on SIBYTE_SWARM
12 The BCM91250A has a Crystal CS4297a on synchronous serial
13 port B (in addition to the DB-9 serial port). Say Y or M
14 here to enable the sound chip instead of the UART. Also
15 note that CONFIG_KGDB should not be enabled at the same
16 time, since it also attempts to use this UART port.
19 tristate "SGI Visual Workstation Sound"
22 Say Y or M if you have an SGI Visual Workstation and you want to be
23 able to use its on-board audio. Read
24 <file:Documentation/sound/oss/vwsnd> for more info on this driver's
27 config SOUND_AU1550_AC97
28 tristate "Au1550/Au1200 AC97 Sound"
29 depends on SOC_AU1550 || SOC_AU1200
32 tristate "Support for Turtle Beach MultiSound Classic, Tahiti, Monterey"
33 depends on (m || !STANDALONE) && ISA
35 Say M here if you have a Turtle Beach MultiSound Classic, Tahiti or
36 Monterey (not for the Pinnacle or Fiji).
38 See <file:Documentation/sound/oss/MultiSound> for important information
39 about this driver. Note that it has been discontinued, but the
40 Voyetra Turtle Beach knowledge base entry for it is still available
41 at <http://www.turtlebeach.com/site/kb_ftp/790.asp>.
43 comment "Compiled-in MSND Classic support requires firmware during compilation."
44 depends on SOUND_PRIME && SOUND_MSNDCLAS=y
46 config MSNDCLAS_HAVE_BOOT
48 depends on SOUND_MSNDCLAS=y && !STANDALONE
51 config MSNDCLAS_INIT_FILE
52 string "Full pathname of MSNDINIT.BIN firmware file"
53 depends on SOUND_MSNDCLAS
54 default "/etc/sound/msndinit.bin"
56 The MultiSound cards have two firmware files which are required for
57 operation, and are not currently included. These files can be
58 obtained from Turtle Beach. See
59 <file:Documentation/sound/oss/MultiSound> for information on how to
62 config MSNDCLAS_PERM_FILE
63 string "Full pathname of MSNDPERM.BIN firmware file"
64 depends on SOUND_MSNDCLAS
65 default "/etc/sound/msndperm.bin"
67 The MultiSound cards have two firmware files which are required for
68 operation, and are not currently included. These files can be
69 obtained from Turtle Beach. See
70 <file:Documentation/sound/oss/MultiSound> for information on how to
74 int "MSND Classic IRQ 5, 7, 9, 10, 11, 12"
75 depends on SOUND_MSNDCLAS=y
78 Interrupt Request line for the MultiSound Classic and related cards.
81 hex "MSND Classic memory B0000, C8000, D0000, D8000, E0000, E8000"
82 depends on SOUND_MSNDCLAS=y
85 Memory-mapped I/O base address for the MultiSound Classic and
89 hex "MSND Classic I/O 210, 220, 230, 240, 250, 260, 290, 3E0"
90 depends on SOUND_MSNDCLAS=y
93 I/O port address for the MultiSound Classic and related cards.
96 tristate "Support for Turtle Beach MultiSound Pinnacle, Fiji"
97 depends on (m || !STANDALONE) && ISA
99 Say M here if you have a Turtle Beach MultiSound Pinnacle or Fiji.
100 See <file:Documentation/sound/oss/MultiSound> for important information
101 about this driver. Note that it has been discontinued, but the
102 Voyetra Turtle Beach knowledge base entry for it is still available
103 at <http://www.turtlebeach.com/site/kb_ftp/600.asp>.
105 comment "Compiled-in MSND Pinnacle support requires firmware during compilation."
106 depends on SOUND_PRIME && SOUND_MSNDPIN=y
108 config MSNDPIN_HAVE_BOOT
110 depends on SOUND_MSNDPIN=y
113 config MSNDPIN_INIT_FILE
114 string "Full pathname of PNDSPINI.BIN firmware file"
115 depends on SOUND_MSNDPIN
116 default "/etc/sound/pndspini.bin"
118 The MultiSound cards have two firmware files which are required
119 for operation, and are not currently included. These files can be
120 obtained from Turtle Beach. See
121 <file:Documentation/sound/oss/MultiSound> for information on how to
124 config MSNDPIN_PERM_FILE
125 string "Full pathname of PNDSPERM.BIN firmware file"
126 depends on SOUND_MSNDPIN
127 default "/etc/sound/pndsperm.bin"
129 The MultiSound cards have two firmware files which are required for
130 operation, and are not currently included. These files can be
131 obtained from Turtle Beach. See
132 <file:Documentation/sound/oss/MultiSound> for information on how to
136 int "MSND Pinnacle IRQ 5, 7, 9, 10, 11, 12"
137 depends on SOUND_MSNDPIN=y
140 Interrupt request line for the primary synthesizer on MultiSound
141 Pinnacle and Fiji sound cards.
144 hex "MSND Pinnacle memory B0000, C8000, D0000, D8000, E0000, E8000"
145 depends on SOUND_MSNDPIN=y
148 Memory-mapped I/O base address for the primary synthesizer on
149 MultiSound Pinnacle and Fiji sound cards.
152 hex "MSND Pinnacle I/O 210, 220, 230, 240, 250, 260, 290, 3E0"
153 depends on SOUND_MSNDPIN=y
156 Memory-mapped I/O base address for the primary synthesizer on
157 MultiSound Pinnacle and Fiji sound cards.
159 config MSNDPIN_DIGITAL
160 bool "MSND Pinnacle has S/PDIF I/O"
161 depends on SOUND_MSNDPIN=y
163 If you have the S/PDIF daughter board for the Pinnacle or Fiji,
164 answer Y here; otherwise, say N. If you have this, you will be able
165 to play and record from the S/PDIF port (digital signal). See
166 <file:Documentation/sound/oss/MultiSound> for information on how to make
167 use of this capability.
169 config MSNDPIN_NONPNP
170 bool "MSND Pinnacle non-PnP Mode"
171 depends on SOUND_MSNDPIN=y
173 The Pinnacle and Fiji card resources can be configured either with
174 PnP, or through a configuration port. Say Y here if your card is NOT
175 in PnP mode. For the Pinnacle, configuration in non-PnP mode allows
176 use of the IDE and joystick peripherals on the card as well; these
177 do not show up when the card is in PnP mode. Specifying zero for any
178 resource of a device will disable the device. If you are running the
179 card in PnP mode, you must say N here and use isapnptools to
180 configure the card's resources.
182 comment "MSND Pinnacle DSP section will be configured to above parameters."
183 depends on SOUND_MSNDPIN=y && MSNDPIN_NONPNP
186 hex "MSND Pinnacle config port 250,260,270"
187 depends on MSNDPIN_NONPNP
190 This is the port which the Pinnacle and Fiji uses to configure the
191 card's resources when not in PnP mode. If your card is in PnP mode,
192 then be sure to say N to the previous option, "MSND Pinnacle Non-PnP
195 comment "Pinnacle-specific Device Configuration (0 disables)"
196 depends on SOUND_MSNDPIN=y && MSNDPIN_NONPNP
198 config MSNDPIN_MPU_IO
199 hex "MSND Pinnacle MPU I/O (e.g. 330)"
200 depends on MSNDPIN_NONPNP
203 Memory-mapped I/O base address for the Kurzweil daughterboard
204 synthesizer on MultiSound Pinnacle and Fiji sound cards.
206 config MSNDPIN_MPU_IRQ
207 int "MSND Pinnacle MPU IRQ (e.g. 9)"
208 depends on MSNDPIN_NONPNP
211 Interrupt request number for the Kurzweil daughterboard
212 synthesizer on MultiSound Pinnacle and Fiji sound cards.
214 config MSNDPIN_IDE_IO0
215 hex "MSND Pinnacle IDE I/O 0 (e.g. 170)"
216 depends on MSNDPIN_NONPNP
219 CD-ROM drive 0 memory-mapped I/O base address for the MultiSound
220 Pinnacle and Fiji sound cards.
222 config MSNDPIN_IDE_IO1
223 hex "MSND Pinnacle IDE I/O 1 (e.g. 376)"
224 depends on MSNDPIN_NONPNP
227 CD-ROM drive 1 memory-mapped I/O base address for the MultiSound
228 Pinnacle and Fiji sound cards.
230 config MSNDPIN_IDE_IRQ
231 int "MSND Pinnacle IDE IRQ (e.g. 15)"
232 depends on MSNDPIN_NONPNP
235 Interrupt request number for the IDE CD-ROM interface on the
236 MultiSound Pinnacle and Fiji sound cards.
238 config MSNDPIN_JOYSTICK_IO
239 hex "MSND Pinnacle joystick I/O (e.g. 200)"
240 depends on MSNDPIN_NONPNP
243 Memory-mapped I/O base address for the joystick port on MultiSound
244 Pinnacle and Fiji sound cards.
247 int "MSND buffer size (kB)"
248 depends on SOUND_MSNDPIN=y || SOUND_MSNDCLAS=y
251 Configures the size of each audio buffer, in kilobytes, for
252 recording and playing in the MultiSound drivers (both the Classic
253 and Pinnacle). Larger values reduce the chance of data overruns at
254 the expense of overall latency. If unsure, use the default.
257 tristate "OSS sound modules"
258 depends on ISA_DMA_API && VIRT_TO_BUS
260 OSS is the Open Sound System suite of sound card drivers. They make
261 sound programming easier since they provide a common API. Say Y or
262 M here (the module will be called sound) if you haven't found a
263 driver for your sound card above, then pick your driver from the
268 config SOUND_TRACEINIT
269 bool "Verbose initialisation"
271 Verbose soundcard initialization -- affects the format of autoprobe
272 and initialization messages at boot time.
275 bool "Persistent DMA buffers"
277 Linux can often have problems allocating DMA buffers for ISA sound
278 cards on machines with more than 16MB of RAM. This is because ISA
279 DMA buffers must exist below the 16MB boundary and it is quite
280 possible that a large enough free block in this region cannot be
281 found after the machine has been running for a while. If you say Y
282 here the DMA buffers (64Kb) will be allocated at boot time and kept
283 until the shutdown. This option is only useful if you said Y to
284 "OSS sound modules", above. If you said M to "OSS sound modules"
285 then you can get the persistent DMA buffer functionality by passing
286 the command-line argument "dmabuf=1" to the sound module.
288 Say Y unless you have 16MB or more RAM or a PCI sound card.
291 tristate "Ensoniq SoundScape support"
293 Answer Y if you have a sound card based on the Ensoniq SoundScape
294 chipset. Such cards are being manufactured at least by Ensoniq, Spea
295 and Reveal (Reveal makes also other cards).
297 If you compile the driver into the kernel, you have to add
298 "sscape=<io>,<irq>,<dma>,<mpuio>,<mpuirq>" to the kernel command
303 tristate "Loopback MIDI device support"
305 Support for MIDI loopback on port 1 or 2.
308 tristate "MediaTrix AudioTrix Pro support"
310 Answer Y if you have the AudioTriX Pro sound card manufactured
313 config TRIX_HAVE_BOOT
314 bool "Have TRXPRO.HEX firmware file"
315 depends on SOUND_TRIX=y && !STANDALONE
317 The MediaTrix AudioTrix Pro has an on-board microcontroller which
318 needs to be initialized by downloading the code from the file
319 TRXPRO.HEX in the DOS driver directory. If you don't have the
320 TRXPRO.HEX file handy you may skip this step. However, the SB and
321 MPU-401 modes of AudioTrix Pro will not work without this file!
323 config TRIX_BOOT_FILE
324 string "Full pathname of TRXPRO.HEX firmware file"
325 depends on TRIX_HAVE_BOOT
326 default "/etc/sound/trxpro.hex"
328 Enter the full pathname of your TRXPRO.HEX file, starting from /.
331 tristate "Microsoft Sound System support"
333 Again think carefully before answering Y to this question. It's
334 safe to answer Y if you have the original Windows Sound System card
335 made by Microsoft or Aztech SG 16 Pro (or NX16 Pro). Also you may
336 say Y in case your card is NOT among these:
338 ATI Stereo F/X, AdLib, Audio Excell DSP16, Cardinal DSP16,
339 Ensoniq SoundScape (and compatibles made by Reveal and Spea),
340 Gravis Ultrasound, Gravis Ultrasound ACE, Gravis Ultrasound Max,
341 Gravis Ultrasound with 16 bit option, Logitech Sound Man 16,
342 Logitech SoundMan Games, Logitech SoundMan Wave, MAD16 Pro (OPTi
343 82C929), Media Vision Jazz16, MediaTriX AudioTriX Pro, Microsoft
344 Windows Sound System (MSS/WSS), Mozart (OAK OTI-601), Orchid
345 SW32, Personal Sound System (PSS), Pro Audio Spectrum 16, Pro
346 Audio Studio 16, Pro Sonic 16, Roland MPU-401 MIDI interface,
347 Sound Blaster 1.0, Sound Blaster 16, Sound Blaster 16ASP, Sound
348 Blaster 2.0, Sound Blaster AWE32, Sound Blaster Pro, TI TM4000M
349 notebook, ThunderBoard, Turtle Beach Tropez, Yamaha FM
350 synthesizers (OPL2, OPL3 and OPL4), 6850 UART MIDI Interface.
352 For cards having native support in VoxWare, consult the card
353 specific instructions in <file:Documentation/sound/oss/README.OSS>.
354 Some drivers have their own MSS support and saying Y to this option
355 will cause a conflict.
357 If you compile the driver into the kernel, you have to add
358 "ad1848=<io>,<irq>,<dma>,<dma2>[,<type>]" to the kernel command
362 tristate "MPU-401 support (NOT for SB16)"
364 Be careful with this question. The MPU401 interface is supported by
365 all sound cards. However, some natively supported cards have their
366 own driver for MPU401. Enabling this MPU401 option with these cards
367 will cause a conflict. Also, enabling MPU401 on a system that
368 doesn't really have a MPU401 could cause some trouble. If your card
369 was in the list of supported cards, look at the card specific
370 instructions in the <file:Documentation/sound/oss/README.OSS> file. It
371 is safe to answer Y if you have a true MPU401 MIDI interface card.
373 If you compile the driver into the kernel, you have to add
374 "mpu401=<io>,<irq>" to the kernel command line.
377 tristate "ProAudioSpectrum 16 support"
379 Answer Y only if you have a Pro Audio Spectrum 16, ProAudio Studio
380 16 or Logitech SoundMan 16 sound card. Answer N if you have some
381 other card made by Media Vision or Logitech since those are not
382 PAS16 compatible. Please read <file:Documentation/sound/oss/PAS16>.
383 It is not necessary to add Sound Blaster support separately; it
384 is included in PAS support.
386 If you compile the driver into the kernel, you have to add
387 "pas2=<io>,<irq>,<dma>,<dma2>,<sbio>,<sbirq>,<sbdma>,<sbdma2>
388 to the kernel command line.
391 bool "Enable PAS16 joystick port"
392 depends on SOUND_PAS=y
394 Say Y here to enable the Pro Audio Spectrum 16's auxiliary joystick
398 tristate "PSS (AD1848, ADSP-2115, ESC614) support"
400 Answer Y or M if you have an Orchid SW32, Cardinal DSP16, Beethoven
401 ADSP-16 or some other card based on the PSS chipset (AD1848 codec +
402 ADSP-2115 DSP chip + Echo ESC614 ASIC CHIP). For more information on
403 how to compile it into the kernel or as a module see the file
404 <file:Documentation/sound/oss/PSS>.
406 If you compile the driver into the kernel, you have to add
407 "pss=<io>,<mssio>,<mssirq>,<mssdma>,<mpuio>,<mpuirq>" to the kernel
411 bool "Enable PSS mixer (Beethoven ADSP-16 and other compatible)"
414 Answer Y for Beethoven ADSP-16. You may try to say Y also for other
415 cards if they have master volume, bass, treble, and you can't
416 control it under Linux. If you answer N for Beethoven ADSP-16, you
417 can't control master volume, bass, treble and synth volume.
419 If you said M to "PSS support" above, you may enable or disable this
420 PSS mixer with the module parameter pss_mixer. For more information
421 see the file <file:Documentation/sound/oss/PSS>.
424 bool "Have DSPxxx.LD firmware file"
425 depends on SOUND_PSS && !STANDALONE
427 If you have the DSPxxx.LD file or SYNTH.LD file for you card, say Y
428 to include this file. Without this file the synth device (OPL) may
432 string "Full pathname of DSPxxx.LD firmware file"
433 depends on PSS_HAVE_BOOT
434 default "/etc/sound/dsp001.ld"
436 Enter the full pathname of your DSPxxx.LD file or SYNTH.LD file,
440 tristate "100% Sound Blaster compatibles (SB16/32/64, ESS, Jazz16) support"
442 Answer Y if you have an original Sound Blaster card made by Creative
443 Labs or a 100% hardware compatible clone (like the Thunderboard or
444 SM Games). For an unknown card you may answer Y if the card claims
445 to be Sound Blaster-compatible.
447 Please read the file <file:Documentation/sound/oss/Soundblaster>.
449 You should also say Y here for cards based on the Avance Logic
450 ALS-007 and ALS-1X0 chips (read <file:Documentation/sound/oss/ALS>) and
451 for cards based on ESS chips (read
452 <file:Documentation/sound/oss/ESS1868> and
453 <file:Documentation/sound/oss/ESS>). If you have an SB AWE 32 or SB AWE
454 64, say Y here and also to "AWE32 synth" below and read
455 <file:Documentation/sound/oss/INSTALL.awe>. If you have an IBM Mwave
456 card, say Y here and read <file:Documentation/sound/oss/mwave>.
458 If you compile the driver into the kernel and don't want to use
459 isapnp, you have to add "sb=<io>,<irq>,<dma>,<dma2>" to the kernel
462 You can say M here to compile this driver as a module; the module is
466 tristate "Yamaha FM synthesizer (YM3812/OPL-3) support"
468 Answer Y if your card has a FM chip made by Yamaha (OPL2/OPL3/OPL4).
469 Answering Y is usually a safe and recommended choice, however some
470 cards may have software (TSR) FM emulation. Enabling FM support with
471 these cards may cause trouble (I don't currently know of any such
472 cards, however). Please read the file
473 <file:Documentation/sound/oss/OPL3> if your card has an OPL3 chip.
475 If you compile the driver into the kernel, you have to add
476 "opl3=<io>" to the kernel command line.
480 config SOUND_UART6850
481 tristate "6850 UART support"
483 This option enables support for MIDI interfaces based on the 6850
484 UART chip. This interface is rarely found on sound cards. It's safe
485 to answer N to this question.
487 If you compile the driver into the kernel, you have to add
488 "uart6850=<io>,<irq>" to the kernel command line.
491 tristate "Gallant Audio Cards (SC-6000 and SC-6600 based)"
493 Answer Y if you have a Gallant's Audio Excel DSP 16 card. This
494 driver supports Audio Excel DSP 16 but not the III nor PnP versions
497 The Gallant's Audio Excel DSP 16 card can emulate either an SBPro or
498 a Microsoft Sound System card, so you should have said Y to either
499 "100% Sound Blaster compatibles (SB16/32/64, ESS, Jazz16) support"
500 or "Microsoft Sound System support", above, and you need to answer
501 the "MSS emulation" and "SBPro emulation" questions below
502 accordingly. You should say Y to one and only one of these two
505 Read the <file:Documentation/sound/oss/README.OSS> file and the head of
506 <file:sound/oss/aedsp16.c> as well as
507 <file:Documentation/sound/oss/AudioExcelDSP16> to get more information
508 about this driver and its configuration.
511 bool "SC-6600 based audio cards (new Audio Excel DSP 16)"
512 depends on SOUND_AEDSP16
514 The SC6600 is the new version of DSP mounted on the Audio Excel DSP
515 16 cards. Find in the manual the FCC ID of your audio card and
516 answer Y if you have an SC6600 DSP.
519 bool "Activate SC-6600 Joystick Interface"
522 Say Y here in order to use the joystick interface of the Audio Excel
526 int "SC-6600 CDROM Interface (4=None, 3=IDE, 1=Panasonic, 0=?Sony?)"
530 This is used to activate the CD-ROM interface of the Audio Excel
531 DSP 16 card. Enter: 0 for Sony, 1 for Panasonic, 2 for IDE, 4 for no
534 config SC6600_CDROMBASE
535 hex "SC-6600 CDROM Interface I/O Address"
539 Base I/O port address for the CD-ROM interface of the Audio Excel
543 tristate "VIDC 16-bit sound"
544 depends on ARM && (ARCH_ACORN || ARCH_CLPS7500)
546 16-bit support for the VIDC onboard sound hardware found on Acorn
549 config SOUND_WAVEARTIST
550 tristate "Netwinder WaveArtist"
551 depends on ARM && ARCH_NETWINDER
553 Say Y here to include support for the Rockwell WaveArtist sound
554 system. This driver is mainly for the NetWinder.
557 tristate "XpressAudio Sound Blaster emulation"
562 config SOUND_SH_DAC_AUDIO
563 tristate "SuperH DAC audio support"
564 depends on CPU_SH3 && HIGH_RES_TIMERS
566 config SOUND_SH_DAC_AUDIO_CHANNEL
569 depends on SOUND_SH_DAC_AUDIO